Documente Academic
Documente Profesional
Documente Cultură
website:http://biz.LGservice.com
MODEL : 32LG300C
CAUTION
32LG300C-ZA
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
CONTENTS .............................................................................................. 2 PRODUCT SAFETY ..................................................................................3 SPECIFICATION ........................................................................................6 ADJUSTMENT INSTRUCTION ...............................................................10 TROUBLE SHOOTING ............................................................................14 BLOCK DIAGRAM...................................................................................25 EXPLODED VIEW .................................................................................. 26 SVC. SHEET ...............................................................................................
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-2-
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.
AC Volt-meter
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.
0.15uF
1.5 Kohm/10W
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-3-
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First. General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver. Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.) General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500F to 600F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature. (500F to 600F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suctiontype solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuit board printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature (500F to 600F) b. First, hold the soldering iron tip and solder the strand against the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.
-4-
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above. Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas). "Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection. Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink. Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder. Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top. 3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered. At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections). 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire. At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board. 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.
-5-
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This specification is applied to the LCD TV used LD85A chassis.
3. Test method
1) Performance: LGE TV test method followed 2) Demanded other specification - Safety: CE, IEC specification - EMC: CE, IEC
Model 32LG300C-ZA EU Market Appliance Safety : IEC/EN60065 EMI : EN55013 EMS : EN55020
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-6-
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-7-
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-8-
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-9-
ADJUSTMENT INSTRUCTION
1. Application Range
This specification sheet is applied to all of the LCD TV with LD85A chassis. 5. Click Auto tab and set as below 6. Click Run. 7. After downloading, check OK message.
(5) filexxx.bin
2. Designation
1) The adjustment is according to the order which is designated and which must be followed, according to the plan which can be changed only on agreeing. 2) Power Adjustment: Free Voltage 3) Magnetic Field Condition: Nil. 4) Input signal Unit: Product Specification Standard 5) Reserve after operation: Above 5 Minutes (Heat Run) Temperature : at 255C Relative humidity : 6510% Input voltage : 220V, 60Hz 6) Adjustment equipments: Color Analyzer (CA-210 or CA110), Pattern Generator (MSPG-925L or Equivalent), DDC Adjustment Jig equipment, SVC remote controller 7) Dont push the IN STOP KEY after completing the function inspection.
(7) ........ OK
(6)
* USB DOWNLOAD
1) Put the USB Stick to the USB socket. 2) Automatically detecting update file in USB Stick - If your downloaded program version in USB Stick is Low, it didnt work. But your downloaded version is High, USB data is automatically detecting. 3) Show the message Copying files from memory.
* Download
1) Execute ISP program Mstar ISP Utility and then click Config tab. 2) Set as below, and then click Auto Detect and check OK message. If display Error, Check connect computer, jig and set. 3) Click Connect tab. If display Cant, Check connect computer, jig, and set.
(1) (3)
4) Updating is staring.
Please Check Speed : To us speed between from 200 KHz to 400 KHz (2) OK
4) Click Read tab, and then load download file(XXXX.bin) by clicking Read.
(4)
filexxx.bin
5) Updating Completed, The TV will restart automatically. 6) If your TV is turned on, check your updated version and Tool option. (explain the Tool option, next stage) * If downloading version is more high than your TV have, TV can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didnt have a DTV/ATV test on production line.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 10 -
<MSPG-1025 Series> Model : 321 in Pattern Generator (480i Mode) Pattern: 65 in Pattern Generator Model : 327 in Pattern Generator (1080i Mode) Pattern: 65 in Pattern Generator
<Fig. 2> Adjustment pattern(COMPONENT) - Adjust by commanding AUTO_COLOR_ADJUST. 2) Confirmation - We confirm whether 0xB3 (480i)/0xBC (1080i) address of EEPROM 0xA2 is 0xAA or not. - If 0xB3 (480i)/0xBC(1080i) address of EEPROM 0xA2 isnt 0xAA, we adjust once more. - We can confirm the ADC values from 0xAD~0XB2 (480i)/0XB6~BB (1080i) addresses in a page 0xA2. * Manual ADC process using Service Remote control. After enter Service Mode by pushing ADJ key, execute ADC Adjust by pushing G key at ADC CALIBRATION : COMPONENT. 480i Mode
<Fig. 1> Adjustment pattern(PC) - Adjust by commanding AUTO_COLOR_ADJUST. 2) Confirmation - We confirm whether 0xAA (RGB) address of EEPROM 0xA2 is 0xAA or not. - If 0xAA (RGB) address of EEPROM 0xA2 isnt 0xAA, we adjust once more - We can confirm the ADC values from 0xA4~0XA9 (RGB) addresses in a page 0xA2 * Manual ADC process using Service Remote control. After enter Service Mode by pushing ADJ key, execute ADC Adjust by pushing G key at ADC CALIBRATION : RGB-PC.
1080i Mode
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 11 -
(5) Adjust Process will finish by execute I2C Command (Inner pattern (Inner pattern (0xF3,0x00)).
1
** Caution ** Color Temperature: COOL, Medium, Warm One of R Gain/G Gain/ B Gain should be kept on 0xC0, and adjust other two lower than C0. (when R/G/B Gain are all C0, it is the FULL Dynamic Range of Module) * Manual W/B process using adjusts Remote control. After enter Service Mode by pushing ADJ key, enter White Pattern off of service mode, and change off -> on. Enter W/B ADJUST by pushing G key at 3.W/B ADJUST.
2 3
4) Enter the IN-START mode, and select RJP Pin Check. 5) The check result is displayed after 1~2 seconds.
* After done all adjustments, Press In-start button and compare Tool option and Area option value with its BOM, if it is correctly same then unplug the AC cable. If it is not same, then correct it same with BOM and unplug AC cable. For correct it to the models module from factory JIG model. * Dont push The IN STOP KEY after completing the function inspection.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 12 -
Confirm whether is normal or not when between power board's ac block and GND is impacted on 1.5kV(dc) or 2.2kV(dc) for one second
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 13 -
TROUBLESHOOTING
1. No Power
(1) Symptom
1) It is not discharged minutely from the module. 2) Light does not come into the front LED.
Yes
No
Connect the Cable.(SC100)
No
Replace the Fuse.
Yes
No
Connect the Cable P1100.
Yes
After all cables connect is removed to PSU, the AC voltage marking is authorized on manual. When ST-BY 5V, +15V are not operated, replace PSU.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 14 -
2. No Raster
(1) Symptom
1) No OSD and image occur at screen. 2) It maintains the condition where the front LED is blue.
No
No
Replace the Power board.
Yes Yes
Check the LCD Module.
No
Yes
No
Is the IC801s output normal? Replace the VSC.
No
Yes
No No
Check the Tuner.
Yes
No
Cable inserts well.
Yes
Change the IC(IC100).
BLOCK A
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 15 -
No
Yes
No Yes
Same as Block A.
No
Check the Tuner. Check the Power.
- RGB Input
No
Check the input source. Is video input of the RGB Jack normal?(Check JK601 _Pin7,11,15)
No
Check the input source.
Yes
Same as Block A.
Yes
No
Check the IC700.
No
Same as Block A.
No
Check the input source.
Yes
Same as Block A.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 16 -
No
Check the input source.
Yes
Same as Block A.
No
Check the input source.
Yes
No
Check the IC700.
No
Same as Block A.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 17 -
No
Check the input source.
Yes
No
Check the IC900, IC901.
Yes
No
Check the IC902.
Yes
No
Check the IC902.
No
Same as Block A.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 18 -
10. No Sound
(1) Symptom
1) LED is blue 2) Screen display but sound is not output.
No
Set on speaker on menu.
Yes
Yes
No
Download the EDID data.
No
Check th Speaker cable.
Yes
Yes
No
Only RF or DTV is no sound? Check the Tuner in/Out.
No
Replace IC100.
Yes
No
Replace IC1000.
Yes
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 19 -
No
Check the input source.
Yes
No
Re-solder or replace the IC100.
Yes
No
Re-solder or replace the IC1001.
Yes
No
Replace the external speaker
No
Check the speaker wire.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 20 -
No
Set YES on SVC menu.
Yes
No
Re-solder or replace the defect part.
Yes
No
Re-solder or replace the defect part.
No
Check the RS-232C Pin7(5V_OUT). Check the RS232C Pin(12V_OUT).
No
Replace the Preamp of IR assy.
Yes
No
Re-solder or replace the defect part.
No
Check the RS-232C Pin4.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 21 -
Yes
No
Yes
No
Check the clock cable.
Yes
No
Re-solder or replace the defect part.
Yes
No
Check the LED clock. Replace the LED clock.
No
Check the Clock assy.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 22 -
No
- Change the Clocky display item from No to Yes. - Change the PR. for TTX Clock item from No to Yes.
Yes
No
Check the clock cable.
Yes
No
Re-solder or replace the defect part.
Yes
No
Check the LED clock. Replace the LED clock.
No
Check the Clock assy.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 23 -
No
Yes
No
Check the supply Power.
Yes
No
Check the I2C line of IC103.
No
No
Yes
No
Set to the alarm time.
Yes
No
Re-solder or replace the defect part.
No
Check the Buzzer(BU1300) & Replace the Buzzer.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 24 -
: Ho t el Func tio n
LVDS RESET R/G/B I2C 24C512 ( IC105) I/ O Exp and er ( IC103) I2C_A_TU KIA7427 ( IC104)
DTV/ TV_VOUT
LCD HD Panel
STMAV340 ( IC700)
DSUB_R/ G/ B
EEPROM
DSUB_H/ V_SYNC
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
PC_L/ R_IN
LGE7363C
( IC100)
I2C
DDR Memo ry
TV Tuner
SIF
TU_TS_DATA PWM
BLOCK DIAGRAM
I2C_D_TU / I2C_A_TU
COMP_Y/ Pb / Pr
COMP_L/ R_IN
5V o r 12V OUT ( To RS232 JACK) Co nt ro l 4b it RJ45 ( JK1300) LED_G/ R & IR KEY1/ 2 IR & Co nt ro l B/ D IR_OUT ( To RS232 JACK) TPA6011A ( IC1001) MUTE EXT_SPK ( JK600) SP ( L)
USB_DM/ DP
MAX3232 ( IC702)
TMDS * 2
CI Slo t
( P800)
CI_CD_1/ 2 IIS KIC7SZ32FU ( IC802)
HDMI_I2C
Sid e_Y/ C/ V/ L/ R
EEPROM EEPROM
5V_HDMI
CEC HPD* 2
NTP3000A ( IC1000)
SP ( R)
EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
401
400
521
540
530
821
550
910
904 901
830
804
803
800
802
801
805
200
120
122
902
905
510
121
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
300
500
- 26 -
900
903
IC100 LGE7363C-LF
R131 R150 22 22
+5V_GENERAL
C4 D4 V15 W15 T15 U15 E4 U16 R17 U18 N18 R18 T16 P17 U17 V17 M16 L16 T14 E16 G18 F18 K17 J17 M18 L18 Y3 V5 U5 Y4 W4 V4 U4 W3 V3 D6 C6 D5 C5 H18 J18 E6 A2 A1 P4 N4 C7 Y15 W5 Y5 T13 B2 B1 C2 C1 D2 D1 E2 E1 G5 E3 E5 F5 E17 G1 G2 F3 F2 F1 H1 H2 H3 J1 J2 J3 K1 K2 F4 K3 L1 J4 K4 L4 L2 L3 M1 G4 N3 M4 N2 G3 M2 N1 P1 P2 R1 R2 R3 R4 T1 T2 T3 T4 R5 U3 U2 U1 V1 V2 W1 W2 Y1 Y2 W13 Y13 W14 Y14 U13 V13 U14 V14 G17 E15 D17 C17 G16 F16 F17 M3 W9 Y18 Y16 Y19 Y17
+5V_CI_Vs
GPIO0/UART_RX1/CEC
EEPROM
TP1335
+5V_ST
RS232C_RXD RS232C_TXD SYSTEM_SDA SYSTEM_SCL DDC_SDA/UART_TX DDC_SCL/UART_RX 5V_MNT EEPROM_WP USB_CTL 5V_CI_CTL BOOSTER Flash_WP_2 DDR_PWR_CTRL AGC_SPEED CLOCK_INT SPI_CSN_2 R227 10K OPT SDA_A_TU SCL_A_TU INV_CTL HPD2 EXT5V_CTRL MUTE RGB_SW EXT12V_CTRL LED_BLUE TU_RESET_N SUB_MUTE HDMI_SW USB_OCD 5V_HDMI_2 5V_HDMI_1 AC_DET EXT5V_DET +3.3V_VDDP_ST R196 0 R244 1M C139 R219 22 4.7uF16V 3216 IR_MST HDMI_CLKHDMI_CLK+ HDMI_RX0HDMI_RX0+ HDMI_RX1HDMI_RX1+ HDMI_RX2HDMI_RX2+ HPD1 OUT R222 10K IC104 KIA7427F 3 2 GND 1 VCC C141 0.22uF 50V
TS_D[0] TS_D[1] TS_D[2] TS_D[3] AR804 33 BUF_TS_CLK,BUF_TS_DATA[0],BUF_TS_SYNC,TU_ERROR_&_BUF_TS_VAL,TU_TS_DATA[1-7]
IC105 AT24C512W-10SI-2.7
A0
R114 0 5V_EEPROM
8 VCC
P800 10067972-050LF
35 36 37 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 G2 2 G1 1 AR832 33 PCM_D[7] PCM_D[0] PCM_D[1] PCM_D[2] AR837 33 2010_A4 C809 0.1uF 16V R830 47 R822 OPT C808 0.1uF 16V OPT R825 100 R827 10K PCM_IRQA_N R823 47 PCM_WE_N R824 47 PCM_OE_N R826 10K OPT R829 47 AR831 33 PCM_D[3] PCM_D[4] PCM_D[5] PCM_D[6] PCM_A[0-14] PCM_CE_N 2010_A4 AR834 PCM_D[0-7]
R132 R151 R152 R136 R137 R153 R138 R139 R154 R134 R135 R158 R280 R279 R141 R142 R143 R149 R159 R160 R161 R162 R144 R145 R163 R146 R164 R165 R166 R147 R148 R167 R140 R130 R278 R277 0
100 100 100 100 100 100 100 10K 100 100 OPT 100 OPT 100 0 0 100 100 100 100 22 100 100 22 100 100 470 100 100 100 100 100 100 100 100
A1
WP
C101 0.1uF
SD/MS_D2 SD/MS_D3
Flash_WP_1
R119 4.7K
SD_SPDZ SD_CMD SD/MS_CLK SD_OCDT SD_PWRCTL SD_MS_INS SD_CDZ INT/GPIO4 GPIO14/UART_TX1 I2S_IN_BCK/GPIO24 I2S_IN_WS/GPIO23 LVSYNC/GPIO22 LHSYNC/GPIO21 LDE/GPIO20 LCK/GPIO19 DOUT_CLK/GPIO20 DIN_D3/GPIO28 DIN_D2/GPIO27 DIN_D1/GPIO26 DIN_D0/GPIO25 DOUT_3/GPIO24 DOUT_2/GPIO23 DOUT_1/GPIO22 DOUT_0/GPIO21 TCON_EXT3/GPIO19 TCON_EXT2/GPIO18 TCON_EXT1/GPIO17
33
38 39 40 41 R816 10K 42 43 44 45 46 47 48 49 50 C802 0.1uF 16V R819 OPT 51 52 53 54 55 56 R814 10K OPT 57 58 59 60 61 62 63 64
OPT R100 0
NC
SCL
GND
SDA
R128 100
R237 10K OPT R228 10K B OPT E C Q100 2SC3052 OPT POWER_ON/OFF1
PCM_IORD_N PCM_IOWR_N BUF_TS_DATA[0] TU_TS_DATA[1] TU_TS_DATA[2] TU_TS_DATA[3]
33
R806 R807
47 47 AR801 33
FLASH MEMORY
R236 0
TU_TS_DATA[4] TU_TS_DATA[5] TU_TS_DATA[6] TU_TS_DATA[7] AR802 33
+5V_GENERAL
+3.3V_VDDP_ST
IC106 S25FL064A
HOLD SCK
TCON_EXT0/GPIO16
16
R116 100
INT2/GPIO26 IRIN2/GPIO25
SPI_SCK SPI_SDI
TESTPIN XTALI XTALO USB_DP USB_DM USB_REXT RESET XIN_RTC XOUT_RTC IRIN/GPIO3 RXCN RXCP RX0N RX0P RX1N RX1P
47 47 47
VCC
15
SI
NC_1
14
NC_8
R117 100
0 0
NC_2
13
NC_7
R183
910
1%
USB_DP USB_DM
NC_3
12
NC_6
NC_4
11
NC_5
CS
10
GND
AR803 33
65 66 67 68
SO
Flash_WP_1
HDMI
RX2N RX2P HOTPLUGA REXT DDCDA_DA DDCDA_CK I2S_OUT_MUTE/CEC HSYNC1 VSYNC1 VCLP
+3.3V_AVDD_DVI
R817 100
R820 OPT
CI_CD2
+3.3V_VDDP_ST
IC107 S25FL064A
HOLD SCK
+5V_GENERAL
B+ G+ R+ COMP_Pb COMP_Y C138 1uF 25V C140 4.7uF 16V 3216 C142 0.1uF 50V C143 10uF 16V 3216 R235 0 2012
BUF_TS_SYNC TU_ERROR_&_BUF_TS_VAL AR805 33 R812 OPT 10K R811 10K C803 0.1uF 16V TU_ERROR_N R828 0 BUF_TS_VAL
IC801 NL17SZ08DFT2G
+3.3V_CI
VCC
15
C112 C113 C114 C115 C105 C106 C107 0.047uF 0.047uF 0.047uF R173 R174 R171 R169 R170 R172 1.2K C122 C124 C125 C126 C127 R182 47 C128 C129 C130 C131 C132 C133 C134 C135 C136 C137 C111 0.1uF R233 R234 R231 R232 100 OPT 100 100 0.1uF 0.1uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF R204 R205 16V 16V 16V 16V 16V 16V 16V 16V 0 0 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF R198 R200 R201 R202 R203 47 47 47 47 47 47 C116 47 C117 C118 47 C119 100 100
NC_1
14
NC_8
NC_2
13
NC_7
NC_3
12
NC_6
NC_4
11
NC_5
VIDEO IN
RIN0M RIN0P HSYNC0 VSYNC0 C1(CVBS7P) Y1(CVBS5P) C0(CVBS6P) Y0(CVBS4P) CVBS3P CVBS2P CVBS1P VCOM1 CVBS0P VCOM0 CVBS_OUT SIF_IN1P SIF_IN1M LINE_IN_0L LINE_IN_0R LINE_IN_1L LINE_IN_1R LINE_IN_2L LINE_IN_2R LINE_IN_3L LINE_IN_3R VIM0 AUVRM
3 BUF_TS_CLK
4 TU_ERROR_&_BUF_TS_VAL
COMP_Pr
CS
10
GND
SO
Flash_WP_2
SIDE_CVBS_IN SC_CVBS_IN TV_CVBS+ DTV/TV_OUT SIF+ SC_L_IN SC_R_IN PC_L_IN PC_R_IN COMP_L_IN COMP_R_IN SIDE_L_IN SIDE_R_IN
R241 C149
IC800 74LVC541A(PW)
VCC
R833 0
+3.3V_CI
20 OPT C813 47uF 16V S C804 0.1uF 50V
OPT
C146 R242
56000pF
A0
19
OE2
IC802 KIC7SZ32FU
+3.3V_CI
5 VCC C811 0.1uF 16V R838 47 PCM_CD_N
AUDIO IN
I/0 EXPANSION
IC103 JLC1562BFEL
R121 0
18
+5V_TU
R240
22K
17
C147
R821 22K
R832 10K
56000pF
TU_TS_CLK
GND
3 CMOS
OUT_Y
A3
C103 0.1uF
1 A0 VDD 16
16
A4
2 A1
SDA 15
15
A5
14
Y4
3 A2
SCL 14
AUDIO OUT
R110 100 RJP_CTRL_0 R107 100 COMP_DET R111 100 RJP_CTRL_1 R108 100 DSUB_DET
4 D0
VDAC 13
5 D1
D7 12
PWM0 PWM1
PWM2 PWM3 SPDIF_IN SPDIF_OUT I2S_OUT_SD I2S_OUT_BCK I2S_OUT_WS I2S_OUT_MCK I2S_IN_SD NC_1 NC_2 SPI_CK1 SPI_DI1
6 D2
D6 11
7 D3
D5 10
8 Vss
D4 9
R179 R180 R194 R195 R184 R185 R197 R175 R176 R177 R178 R181 R199
OPT 100 100 100 100 470 100 100 100 100 100 100 100
KEY1 KEY2 MODULE_SEL BUZZ_PWM A_DIM PWM_DIM LED_RED CLOCK/AMP_SCL AMP_RST MS_LRCH MS_SCK MS_LRCK AUDIO_MCLK CLOCK/AMP_SDA SPI_SCK SPI_SDI SPI_SDO SPI_CSN_1 //BOOTSTRAP PWM[1:0]=10 +3.3V_VDDP_ST
A6
13
Y5
A7
+3.3V_VDDP_ST R208 1K OPT BUZZ_PWM A_DIM MODULE_SEL R209 1K R218 1K OPT R221 0 22" R217 1K 26"/32"/37"/42" R220 3.3K 26"/32"/37"/42" R224 3.3K
R221 OX X X X
R220
R224 X
12
Y6
O O O
X O X
10
11
Y7
FLASH
SPI_DO1 SPI_CZ1
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
22LG300C-ZA MAIN_1
2007.10.27
13
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
XXLG300C-ZA
2007.08.07
PCMCIA
8 13
+5V_TU
LED CLOCK
B +5V_ST
L501 E Q1300 2SA1504S B C C E Q1301 2SA1504S B C E Q1302 2SA1504S B C E Q1303 2SA1504S B C 12 E Q1304 2SA1504S 13 LEMC3225T-6R8M
R567 0 +5V_TU_A
L508 LEMC3225T-6R8M
11 L1300 MBW3216-501TF 8 VCC C1303 0.1uF C1304 10uF 16V R1331 4.7K OPT R1306 22 R1308 22 R1307 22 R1332 0 CLOCK_INT R1309 33K CLOCK/AMP_SCL R1338 220 1 2 G C1306 100pF 50V RA2/AN2/VREF1 18 RA1/AN1 I IC1303 PIC16F819-I/SO IC1305 KID65003AF 6 I1 1 16 O1 R1320 10 5 I2 2 15 O2 R1319 10 4 RA0/AN0 I3 3 14 O3 R1325 10 3 RA7/OSC1/CLKI I4 4 13 O4 R1321 10 2 RA6/OSC2/CLKO +5V_ST I5 5 12 O5 R1322 10 1 VDD I6 6 11 O6 R1324 10 R1323 10 +5V_ST 12505WS-12A00 P1301 COMMON 7 8 C1307 47uF 16V
TU500 TDFV-G135D1
ANT[5V] BB[CTR] GND_1 +B[5V] NC_1 RF_AGC TP[VT] NC_2 R518 GND_2 SDA_T SCL_T AIF_1 AIF_2 NC_3 VIDEO AUDIO SIF SDA SCL C502 100pF 50V R516 33 R500 0 C512 47pF 50V C511 47pF 50V R519 47 47 R501 C504 0.1uF 50V 0 C510 1000pF 50V C513 0.1uF 50V C516 0.1uF 50V C519 100uF 16V
10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
XI
XO
IRQ/FT/OUT/SQW
L500 LEMC3225T-6R8M
Q500 2SC3052 E
VBAT
SCL
VSS R1300 1K
SDA
IC1302 KIA7042AF 3
+5V_TU_A SDA_A_TU C527 4.7uF 16V R559 270 R563 TV_CVBS+ R521 4.7K R523 4.7K +5V_TU R560 270 E B R558 OPT SDA_D_TU SCL_D_TU 1.2K R522 R517 33 B R542 4.7K C C 2SA1530A-T112-1R Q503 0 C528 270pF 50V OPT +5V_TU_A
BA1300 BATTERY 2 1
SCL_A_TU
RA3/AN3/VREF+
17
RA4/AN4/T0CKI
16
RA5/MCLR/VPP
15
VSS +5V_ST
14
R544 470 E
RJP
R1301 10K
+5V_SUBAMP
13
RB7/T1OSI/PGD
I7
10
O7
RB1/SDI/SDA
R1302 10K
R1303 10K
R1304 10K
12
RB6/T1OSO/T1CKI/PGC
1.2K R520
GND
RST 3.3V 1.8V ERR MCL D7 D6 D5 D4 D3 D2 D1 D0 VAL SYNC C500 0.1uF 50V C501 0.1uF 50V C503 47pF 50V
+3.3V_TU
22 23
+3.3V_TU R503 R504 R505 R506 R507 R508 R509 R510 R511 R512 R513 33 33 33 33 33 33 33 33 33 33 33 TU_TS_CLK TU_TS_DATA[7] TU_TS_DATA[6] TU_TS_DATA[5] TU_TS_DATA[4] TU_TS_DATA[3] TU_TS_DATA[2] TU_TS_DATA[1] TU_TS_DATA[0] TU_TS_VAL TU_TS_SYNC +3.3V_TU TU_TS_CLK,TU_TS_DATA[0-7],TU_TS_SYNC,TU_TS_VAL C505 1000pF 50V C509 0.1uF 50V C515 0.1uF 50V C518 100uF 16V +1.8V_TU
IC500 TPS2042ADRG4
RJP_CTRL_0
RB3/CCP1/PGM
10
RJP_CTRL_1
R528 100
R533 4.7K TU_RESET_N C521 0.1uF 50V OPT R578 R561 0 0 R595 R596 0 0 R586 0 R590 0 OPT R587 0 R588 0 OPT 0 R591 OPT R592 0 OPT R593 0 OPT GND GND_TU GND
RJP_CTRL_2
RJP_CTRL_3
RJP_DET
7 6
GND_TU
ZD1300
ZD1301
ZD1302
ZD1303
8 9
USB 5V
+5V
WIRED IR BUZZER
+5V_ST IC1300 74LX1G14CTR ** Polarity Notation in PCB C1302 0.1uF 16V 1Y BU1300 PKLCS1212E4001-R1 6A 7A NC 1 5 VCC 4 5 7B 1 6B 2 8 T_TERMINAL2 SHIELD_PLATE T_TERMINAL1 B_TERMINAL1 R_SPRING T_SPRING B_TERMINAL2 JK1301 PEJ024-01 3 E_SPRING
SHIELD
IR_IN IR_OUT
+5V_ST
R1313 O X
R1314 O X
R1315 X O
R1316 X O
R1337 O X
A0 1
IC1304 74AC08SJ
+5V_ST
14
VCC R1318 4.7K C1309 0.1uF R1327 10K B2 R1326 22 C R1329 10K GND_TU C506 1000pF 50V C508 0.1uF 50V C514 0.1uF 50V C517 100uF 16V
GND
OC1
IN
OUT1
EN1
B0
13
A2
OUT2
EN2
OC2
O0
12
A1
11
O2
Q1305 2SC3875S E
IR_MST
B1
10
A3
1A BUZZ_PWM GND
Q1306 2SC3875S
IROUT_JK
O1
B3
GND
O3 IROUT_HDMI1
IROUT_HDMI2
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
XXLG300C-ZA
2007.08.07
Tuner
5 13
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
XXLG300C-ZA Commercial
2007.10.27 13 13
LGE Internal Use Only
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
LGE7363C-LF
+3.3V_VDDP VD33_1 VD33_2 VD33_3 VD33_4 VD33_2_1 VD33_2_2 AVDD_33_1 AVDD_33_2 AVDD_33_3 AVDD_33_4 AVDD_33_5 AVDD_33_6 AVDD_MPLL P11 P12 P13 P14 P9 P10 G6 H6 J6 K6 L6 G7 E7 B14 D7 G12 L17 P6 P3 G13 G11 G10 A15 G8 G9 M6 N6 G14 H14 J14 K14 L14 M14 N14 P7 P8 C250 0.1uF 50V C251 0.1uF 50V C261 0.1uF 50V C266 0.1uF 50V +1.25V_AVDD_DVI C252 0.1uF 50V C254 0.1uF 50V OPT C285 0.1uF 50V +2.5V_DDR C286 OPT 0.1uF 50V 0.1uF C271 C270 1000pF +3.3V_AVDD_MPLL +3.3V_AVDD_MEMPLL C263 0.1uF 50V +3.3V_AVDD_OTG C272 0.1uF 50V +3.3V_AVDD_LPLL C281 0.1uF 50V +3.3V_AVDD_AU C283 0.1uF 50V C257 0.1uF 50V C258 0.1uF 50V +3.3V_AVDD_ADC ST_BY 3.3V C259 0.1uF 50V C260 0.1uF 50V
SDR_CKL+ SDR_CLKSDR_DQS_0 SDR_DQM_0 SDR_DQ_0 SDR_DQ_1 SDR_DQ_2 SDR_DQ_3 SDR_DQ_4 SDR_DQ_5 SDR_DQ_6 SDR_DQ_7 SDR_DQS_1 SDR_DQM_1 SDR_DQ_8 SDR_DQ_9 SDR_DQ_10 SDR_DQ_11 SDR_DQ_12 SDR_DQ_13 SDR_DQ_14 SDR_DQ_15 SDR_DQS_2 SDR_DQM_2 SDR_DQ_16 SDR_DQ_17 SDR_DQ_18 SDR_DQ_19 SDR_DQ_20
C15 B15 B7 A7 B3 A3 B4 A4 B5 A5 B6 A6 B12 A12 B8 A8 B9 A9 B10 A10 B11 A11 A20 B20 B16 A16 B17 A17 B18 A18 B19 A19 G19 G20 C19 C20 D19 D20 E19 E20 F19 F20 E10 D10 C10 E11 D11 E13 D13 E12 D12 C12 C11 C13 B13 A13 E14 D14 C14 D15 H19 H20 J19 J20 K19 K20 L19 L20 M19 M20 N19 N20 P19 P20 R19 R20 T19 T20 U19 U20 V19 V20 W19 W20 J16 H16 H17 K18 Y7 W7 V7 U7 T7 Y6 W6 V6 U6 T5 T6 Y12 W12 V12 U12 Y11 W11 V11 U11 T11 Y10 W10 V10 U10 T10 Y9 V9 U9 T9 Y8 W8 V8 U8 T8 P16 R16 M17 N17 T17 V18 P18 T18 N16 K16 AR251 22 AR250 22 AR253 22 AR252 22 AR255 22 AR254 22
B R641 75 C622 100uF 16V R623 R605 22 SC_FB 10 SC_R R644 1K E R646 300
21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
AVDD_MEMPLL AVDD_USB AVDD_LPLL_1 AVDD_LPLL_2 AVDD_AU AVDD_SIF AVDD_DDR_1 AVDD_DDR_2 AVDD_DDR_3 MVREF AVDD_DVI_1 AVDD_DVI_2 VDDC_1 VDDC_2 VDDC_3 VDDC_4 VDDC_5 VDDC_6 VDDC_7 VDDC_8 VDDC_9 VDD_PWR AVDD_RTC
SDR_DQ_21 SDR_DQ_22 SDR_DQ_23 SDR_DQS_3 SDR_DQM_3 SDR_DQ_24 SDR_DQ_25 SDR_DQ_26 SDR_DQ_27 SDR_DQ_28 SDR_DQ_29 SDR_DQ_30 SDR_DQ_31 SDR_CASZ SDR_RASZ SDR_WEZ SDR_BA0 SDR_BA1 SDR_AD12 SDR_AD11 SDR_AD10 SDR_AD9 SDR_AD8 SDR_AD7 SDR_AD6 SDR_AD5 SDR_AD4 SDR_AD3 SDR_AD2 SDR_AD1 SDR_AD0 RXO0RXO0+
. GND . G . .
75
1%
CONTROL
R419 100 1%
R603 75 1%
IR
SC_L_IN D615 5.6V OPT R645 470K C628 OPT R660 12K C639 560pF 50V L612 MBW3216-501TF +16V_SC
KEY1
KEY2
1/16W
R582 0 OPT
1/16W
E 2SA1530A-T112-1R Q610 B C L607 BG2012B080TF C631 22uF 16V Q612 2SC3052 R653 1.5K E R659 470 C642 10uF 6.3V LVB_3P LVB_4P B DTV/TV_L_OUT R665 15K C645 OPT
VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VSS_12 VSS_13 VSS_14 VSS_15 VSS_16 VSS_17 VSS_18 VSS_19 VSS_20 VSS_21 VSS_22 VSS_23 VSS_24 VSS_25 VSS_26 VSS_27 VSS_28 VSS_29 VSS_30 VSS_31 VSS_32 VSS_33 VSS_34 VSS_35 VSS_36 VSS_37 VSS_38 VSS_39 VSS_40
RXO3+ RXO4RXO4+ RXE0RXE0+ RXE1RXE1+ RXE2RXE2+ RXECRXEC+ RXE3RXE3+ RXE4RXE4+ TS1_CLK TS1_SYNC TS1_VLD TS1_D0 TS0_CLK TS0_SYNC TS0_VLD TS0_D7 TS0_D6 TS0_D5 TS0_D4 TS0_D3 TS0_D2 TS0_D1 TS0_D0 PCM_A0 PCM_A1 PCM_A2 PCM_A3 PCM_A4 PCM_A5 PCM_A6 PCM_A7 PCM_A8 PCM_A9 PCM_A10 PCM_A11 PCM_A12 PCM_A13 PCM_A14 PCM_D0 PCM_D1 PCM_D2 PCM_D3 PCM_D4 PCM_D5 PCM_D6 PCM_D7 PCM_IORD PCM_IOWR PCM_OE_N PCM_WE_N PCM_REG_N PCM_CE_N PCM_IRQA PCM_WAIT_N PCM_RESET PCM_CD_N
LVB_CKP
LVB_1P
M9 M8 L12 L11 L10 L9 L8 K12 K11 K10 K9 K8 J12 J11 J10 J9 J8 C3 D3 H4 C8 C9 D8 D9 E8 E9 C16 D16 C18 D18 E18 T12 V16 W16 W17 W18 Y20
1/16W
1/16W
SC_R_IN D613 5.6V OPT R643 470K C624 OPT C630 330pF 50V R657 12K C637 560pF 50V
LVB_3M
LVB_2M
LVB_1M
LVB_CKM
LVB_0M
LVB_4M
R407 1.3K
PCM_A[0] PCM_A[1] PCM_A[2] PCM_A[3] PCM_A[4] PCM_A[5] PCM_A[6] PCM_A[7] PCM_A[8] PCM_A[9] PCM_A[10] PCM_A[11] PCM_A[12] PCM_A[13] PCM_A[14]
C B E R656 470
C640 10uF 6.3V DTV/TV_R_OUT R662 15K C643 0.1uF 16V OPT
R408 1.3K
R433 1.3K
R434 1.3K
TS_D[0-7]
R435 0
R655 1K
R661 47K
PCM_A[0-14]
C402 47uF 25V
PCMCIA
PCM_D[0-7]
PCM_IORD_N PCM_IOWR_N PCM_OE_N PCM_WE_N PCM_REG_N PCM_CE_N PCM_IRQA_N PCM_WAIT_N PCM_RESET PCM_CD_N
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
SCART
13
[22"]
P401 22" VDD(5V) VDD(5V) VDD(5V) PANEL_POWER 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 GND 5 4 3 2 GND GND GND RXOC+ RXEC+ RXO0+ RXO1+ RXO2+ RXO3+ RXOCRXE0+ RXE1+ RXE2+ RXE3+ RXECRXO0RXO1RXO2RXO3RXE0RXE1RXE2RXE3NC 1
Module
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
XXLG300C-ZA MAIN_2
2007.08.07 2 13
LVB_3P
LVB_1P
LVA_2M
LVB_3M
LVB_2M
LVA_3P
LVA_1P
LVA_2P
LVA_0P
LVB_2P
LVB_1M
LVB_0P
LVA_CKP
LVB_CKP
LVA_3M
LVA_1M
LVA_0M
COMPONENT
+5V_GENERAL JK701 PPJ209-02 2A 4A 3A 2B [GN]1P_CAN [GN]CONTACT [GN]O_SPRING [BL]1P_CAN [BL]C_LUG_L [RD]1P_CAN1 [RD]C_LUG_L [WH]1P_CAN [WH]C_LUG_L [RD]1P_CAN2 [RD]CONTACT [RD]O_SPRING D713 CDS3C05GTA 5.6V OPT D712 CDS3C05GTA 5.6V OPT R729 470K D711 CDS3C30GTH 30V OPT R728 75 D710 CDS3C30GTH 30V OPT R727 75 D709 CDS3C30GTH 30V OPT R726 75 D714 CDS3C05GTA 5.6V OPT C712 0.1uF 50V C713 0.1uF 50V C714 0.1uF 50V R737 10K COMP_L_IN C715 100pF 50V R736 10K COMP_R_IN R730 470K C716 100pF 50V R743 12K R742 12K R735 22 COMP_Pr R734 22 COMP_Pb R733 22 COMP_Y R724 10K R725 1K COMP_DET
RS232C
+3.3V_VDDP_ST
R755 4.7K
RS232C_TXD
1uF
1B
16
VCC
+2.5V_DDR
LVA_CKM
LVB_CKM
LVB_0M
50V
16V
DSUB_G
1uF
1C
15
OE_N
ROUT2
RIN2
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF C308
C301
0.1uF
C302
C303
C304
C305
C306
C307
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
C313
C317
C314
C315
C318
C320
DSUB_B
MAX3232CDR
C702
1uF
2C
13
1A
G+
2C 5C
DIN1 1 6 2 7 3 8 4 9 5 10 0 R769 EXT12V_9P OPT 30V CDS3C30GTH D727 VCC OPT 30V CDS3C30GTH D726 R766 0 R768 0 OPT_EXT12V_7P R764 100 DOUT1 R761 100 ROUT1
11 IC702
ADDRESS TOTAL LENGTH < 3000 mil (76.2mm) DDR1 & DDR2 different length range = +/- 25 mil (max +/- 50 mil)
SC_R
C703
1uF
3B
12
2A
12
B+ 2D R+ 5D
C2-
+2.5V_DDR
IC300
+2.5V_DDR
+2.5V_DDR
IC301
+2.5V_DDR
C705 DSUB_R
1uF
3C
11
3A
RIN1
13
C2+
4B
10
4A 2E GND 4E 3E
14
C1-
HY5DU561622FTP-4-C
HY5DU561622FTP-4-C
4C R701 0
GND
15
V+
AR300 22 1/16W
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34
VSS_3 DQ15 VSSQ_5 DQ14 DQ13 VDDQ_5 DQ12 DQ11 VSSQ_4 DQ10 DQ9 VDDQ_4 DQ8 NC_6 VSSQ_3 UDQS NC_5 VREF VSS_2 UDM /CLK CLK CKE NC_4 A12 A11 A9 A8 A7 A6 A5 A4 VSS_1 1% R301 56 1% R304 300 R324 05 % R323 05% R322 56 1% R305 56 1% AR308 22 1/16W AR307 22 1/16W
AR311 22 1/16W
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34
VSS_3 DQ15 VSSQ_5 DQ14 DQ13 VDDQ_5 DQ12 DQ11 VSSQ_4 DQ10 DQ9 VDDQ_4 DQ8 NC_6 VSSQ_3 UDQS NC_5 VREF VSS_2 UDM /CLK CLK CKE NC_4 A12 A11 A9 A8 A7 A6 A5 A4 VSS_1 1% R328 56 1% R315 300 R325 1% R327 05 % R326 05 % 56 R316 56 1% C316 0.1uF 50V C319 0.1uF 50V R320 1K 1% AR319 22 AR318 22
16
C1+
Side AV
JK618 PPJ218-01 4A 5A 2A 3B 2B 4C 5C 2C [YL]O_SPRING [YL]CONTACT [YL]U_CAN [WH]C_LUG [WH]U_CAN [RD]O_SPRING [RD]CONTACT [RD]U_CAN CDS3C05GTA D701 R705 5.6V 470K C734 OPT CDS3C05GTA D700 R708 5.6V 470K CDS3C05GTA D705 5.6V R712 10K R703 CDS3C30GTH D706 30V R713 75 C736 330pF 50V OPT +5V_GENERAL
L704 3.3uH
USB
JK700 UB01123-4HHS-4F
AR301 22 1/16W
AR312 22 1/16W
+5V_USB
D723 ENKMC2838-T112 A1
+5V_ST
PC(RGB)
C724 0.1uF
IC701 AT24C02BN-10SU-1.8
C A2
R716 10K SIDE_L_IN C737 330pF 50V R709 10K C708 330pF R718 12K C732 560pF R715 12K C707 560pF
NC_1
USB_DM
A0
R754 4.7K
8 VCC
R757 4.7K
VDDQ_3 R302 56 LDQS NC_2 VDD_2 NC R300 56 LDM /WE /CAS /RAS /CS NC_3 BA0
+2.5V_DDR DQS0
C311 0.1uF 50V C325 0.1uF 50V R309 1K 1% R310 1K 1%
0.1uF
SC_B
RGB_SW
5B
0.1uF
C701
1uF
14
C321
2B
JK704 KCN-DS-1-0088
DIN2
DOUT2
0.1uF C322
10
+2.5V_DDR
XXLG300C-ZA
2007.08.07
R313 56
DQS1
USB_DP
A1
1%
DQS3
1%
SIDE_R_IN
WP
A2
SCL
GND
SDA
C725 18pF 50V R746 10K D717 30V C720 22pF 50V R752 10K D718 30V CDS3C30GTH
R758 22
R760 22
1%
DQM0 MCLKMCLK+ CLKE MADR[12] MADR[11] MADR[9] MADR[8] MADR[7] MADR[6] MADR[5] MADR[4]
R303 56
1%
R744 100
EXT_SPEAKER
JK600 PEJ024-01 3 6A 7A 4 5 7B 6B 8 E_SPRING T_TERMINAL1 B_TERMINAL1 R_SPRING T_SPRING EXT_SPK_L+ B_TERMINAL2 T_TERMINAL2 SHIELD_PLATE OPT C739 1uF 10V R771 0 OPT C738 1uF 10V R770 0 EXT_SPK_L-
PC AUDIO
JK702 PEJ024-01 3 6A 7A 4 5 7B 6B 8 E_SPRING T_TERMINAL1 B_TERMINAL1 R_SPRING T_SPRING B_TERMINAL2 T_TERMINAL2 SHIELD_PLATE D716 CDS3C05GTA 5.6V OPT C718 100pF 50V D715 CDS3C05GTA 5.6V OPT C717 100pF 50V R738 10K PC_R_IN R731 470K R740 5.1K
DSUB_VSYNC DSUB_HSYNC
R747 22 R753 75 C721 OPT D719 CDS3C30GTH 30V R762 0 R748 22 OPT
R739 10K PC_L_IN R732 470K R741 5.1K DSUB_R R751 75 C723 OPT D721 CDS3C30GTH 30V R749 22
10
16
JK703 KCN-DS-1-0089
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
D
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
XXLG300C-ZA
2007.08.07
Interface
7 13
LGE Internal Use Only
+3.3V_CI
+2.5V_DD R DQS2
R321 1K 1%
DQM2 MCLKMCLK+ CLKE MADR[12] MADR[11] MADR[9] MADR[8] MADR[7] MADR[6] MADR[5] MADR[4]
XXLG300C-ZA
2007.08.07 3 13
DDR
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
26"/32"/37"/42"
TS SIGNAL
33 33 33 33
20
18
16
14
12
26
24
22
10
L608 BG2012B080TF
R652 10K
[26"/32"/37"/42"]
1/16W
25
23
21
19
17
15
13
11
26"/32"/37"/42"
M10
LVB_0P
LVDS
LVB_2P
M11
R401 0
M12
RXO3-
1/16W
26"/32"/37"/42"
R585 0
R658 1K
R664 47K
26"/32"/37"/42"
IC100 LGE7363C-LF
RXO1-
LVB_0M LVB_0P LVB_1M LVB_1P LVB_2M LVB_2P LVB_CKM LVB_CKP LVB_3M LVB_3P LVB_4M LVB_4P LVA_0M LVA_0P LVA_1M LVA_1P LVA_2M LVA_2P LVA_CKM LVA_CKP LVA_3M LVA_3P
R583 0
JK601
R584 0 OPT
LED_BLUE
LED_RED
R654 10K
R422 OPT
R607 10
R420 100 1%
R421 3.3K
SC_B
IR & LED
+1.25V_VDDC
R269 R266 R267 R268 R265 R264 R260 R261 R262 R263 R259 R256 R257 R258 R252 R253 R254 R255
DQS3 DQM3 MDATA[24] MDATA[25] MDATA[26] MDATA[27] MDATA[28] MDATA[29] MDATA[30] MDATA[31] 56 56 56 56 56 56 56 56 56 56 56 56 56 56 56 56 56 56
L403 BG2012B080TF
L405 BG2012B080TF
10 SC_G
+3.3V_VDDP_ST
M_CAS M_RAS M_WE BA0 BA1 MADR[12] MADR[11] MADR[10] MADR[9] MADR[8] MADR[7] MADR[6] MADR[5] MADR[4] MADR[3] MADR[2] MADR[1] MADR[0]
SC_ID
R669 11K
+3.3V_VDDP_ST
R666 56K
SC_ID
R423 3.3K
+5V_ST
R670 1K
L404 BG2012B080TF
SCART_DET
L406 BG2012B080TF
L407 BG2012B080TF
D402 CDS3C05GTA
R667 10K
5.6V
R601
R610 75 1%
L410 MBW3216-501TF
+5V_GENERAL
Module&Ctl
XXLG300C-ZA
DQS2 DQM2 MDATA[16] MDATA[17] MDATA[18] MDATA[19] MDATA[20] MDATA[21] MDATA[22] MDATA[23]
GND SC_FB
50V
DDR MEMORY
C410 0.1uF
D400 CDS3C05GTA
GND
5.6V
DQS0 DQM0 MDATA[0] MDATA[1] MDATA[2] MDATA[3] MDATA[4] MDATA[5] MDATA[6] MDATA[7] DQS1 DQM1 MDATA[8] MDATA[9] MDATA[10] MDATA[11] MDATA[12] MDATA[13] MDATA[14] MDATA[15]
12505WS-08A00
MCLK+ MCLK-
2007.08.07
C409 1000pF 50V
IC100 LGE7363C-LF
IC100
SDR_CKE
A14
CLKE
R274 22 R275 22
+16V_SC
R671 0 SC_CVBS_IN R648 75 1% D611 30V OPT 50V 56pF C635 OPT C641 220pF 50V E 2SA1530A-T112-1R Q607 C B R647 470 Q608 2SC3052 C
GND 22
R649 47K
4 13
+16V_AMP +3.3V_VDDP_ST 5V_HDMI_1 R968 47K OPT B E R967 10K HPD1 IC900 AT24C02BN-10SU-1.8 A2 A1 ENKMC2838-T112 D900 100 DDC_SDA_1 R976 R978 R903 100 DDC_SCL_1 0 22 0 R965 CK-_HDMI1 CK+ D0D0_GND 0 0.1uF C905 0.1uF C906 0.1uF C907 0.1uF C909 0.1uF C911 0.1uF C912 0.1uF C910 0.1uF C913 D0+ D1D1_GND D1+ D2D2_GND D2+ GND GND 0 R958 D2+_HDMI1 SDA3 SCL3 GND_1 B31 A31 VCC_1 B32 JK900 GND A32 GND_2 B33 A33 VCC_2 +3.3V_VDDP_ST 5V_HDMI_2 R905 47K OPT R908 3.9K B E R901 10K HPD2 B34 A34 GND_3 VSADJ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 IC902 TMDS351PAG 0R 960 GND_7 VCC_8 VCC_7 D1+_HDMI1 HPD3 A24 B24 0R 959 D2-_HDMI1 HPD2 SDA2 SCL2 VDD A23 B23 A22 B22 A21 B21 0 R962 D0+_HDMI1 R914 0 R961 D1-_HDMI1 C915 10uF 6.3V AUDIO_MCLK EEPROM_WP IC901 A2 A1 AT24C02BN-10SU-1.8 ENKMC2838-T112 D901 C A0 1 8 VCC R910 0 5V_HDMI_2 +5V_ST +1.8V_AMP MLB-201209-0120P-N2 +1.8V_AMP +1.8V_AMP OPT R1048 0 L1014 R1049 0 C1003 100pF 50V C1007 1000pF 50V R1002 3.3K +3.3V_CI 0 R964 CK+_HDMI1 0 R963 D0-_HDMI1 DDC_SDA_1 CK-_HDMI1 DDC_SCL_1 CK+_HDMI1 D0+_HDMI1 MMBD301LT1G D905 D2+_HDMI1 D1+_HDMI1 IROUT_HDMI1 CEC_REMOTE D2-_HDMI1 D1-_HDMI1 D0-_HDMI1 +5V_ST A1 2 7 WP R911 0 C902 0.1uF R912 47K SCL R971 22 DDC_SCL_1 PGND1A_2 PGND1A_1 PGND1B_2 PGND1B_1 PVDD1A_2 PVDD1A_1 PVDD1B_2 PVDD1B_1 GND OUT1A_2 OUT1A_1 OUT1B_2 OUT1B_1 4 5 SDA R972 22 DDC_SDA_1 AMP_RST C1006 1000pF 50V R1001 100 R915 47K C1011 22000pF 50V A0 1 8 VCC C C1012 220uF 35V EEPROM_WP 5V_HDMI_1 +16V +5V_ST L1206 MBW3216-501TF +16V_AMP +16V_AMP +16V_AMP OPT C1030 1000pF 50V R1011 5.6 OPT D1004 1N4148W 100V OPT C1051 1000pF 50V R1010 5.6 OPT D1003 1N4148W 100V L1010 DA-8580 EAP38319001 2F C1040 0.1uF 50V 1S 1F C1038 0.47uF 50V C1041 0.1uF 50V R1023 4.7K SPK_L+ C1044 0.01uF 50V R1028 3.3 R1029 3.3 C1045 0.01uF 50V SPK_L-
22 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 20 21
R1014 5.6 C1034 1000pF 50V C1035 1000pF 50V R1015 5.6
2S
R1022 4.7K
R1005 3.3 C1013 0.01uF 50V C1017 0.1uF 50V C1021 0.1uF 50V C1050 0.1uF 50V
SPEAKER_L
+3.3V_CI
A2
C1015 22000pF 50V +16V_AMP C1016 1uF 16V OPT C1031 1000pF 50V OPT R1012 5.6 C1049 22000pF 50V +16V_AMP D1005 1N4148W 100V C1046 0.01uF 50V C1039 0.47uF 50V C1042 0.1uF 50V R1024 4.7K R1030 3.3 R1031 3.3 C1043 0.1uF 50V R1025 4.7K C1047 0.01uF 50V
R980 OPT
0 30V
56
55
54
53
52
51 50
49
48
47
46
45
44
C1009 1uF
BST1A VDR1A AD VSS_IO CLK_I CLK_O VDD_IO DGNDPLL AGNDPLL LFM AVDDPLL DVDDPLL NC_1
43
VDR1B
BST1B
42 41 40 39 38 37 36 35 34 33 32 31 30 29
SPK_R+ R1016 5.6 C1036 1000pF 50V C1037 1000pF 50V R1017 5.6
0.1uF
C904
10V /RESET
PGND2A_2 PGND2A_1 OUT2A_2 OUT2A_1 PVDD2A_2 PVDD2A_1 PVDD2B_2 PVDD2B_1 OUT2B_2 OUT2B_1 PGND2B_2
MLB-201209-0120P-N2
OPT C1032 1000pF 50V OPT R1013 5.6 D1006 1N4148W 100V
L1013
1S
1F
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
A14 B14 VCC_6 A13 B13 GND_6 A12 B12 VCC_5 A11 B11 SCL1 SDA1 HPD1 EQ S2 +3.3V_VDDP_ST 0 R921
A1 D2+_HDMI2 D2-_HDMI2 A2 D1+_HDMI2 D1-_HDMI2 D0+_HDMI2 D0-_HDMI2 CK+_HDMI2 CK-_HDMI2 DDC_SCL_2 DDC_SDA_2 R920 4.7K GND
WP
C903 0.1uF
64
63
62
61
60
59
58
57
56
55
54
53
52
51 50
49
R913 47K
SPK_R-
SCL R973 22
+16V_AMP
DVSS
BCK
SDA
SCL
PROTECT
SDATA
VDR2B
BST2B
DVDD
WCK
PWM_3B/PWM_HP2
PWM_3A/PWM_HP1
PGND2B_1
FAULT
C Q901 2SC3052 C900 0.1uF 50V R940 2K R900 1K R969 R970 R979 R907 100
MS_LRCH MS_LRCK MS_SCK R1003 R1004 100 100 C1061 33pF 50V C1062 33pF 50V
22000pF 50V L1015 C1024 10uF 16V AC_DET IC1001 0 MUTE +5V_ST TPA6011A4PWPRG4
Z4
Z3
Z2
Z1
S1
Y4
Y3
Y2
Y1
VCC_3
GND_4
VCC_4
GND_5
SCL_SINK
HPD_SINK
SDA_SINK
C1025 0.1uF
PGND_1 R1056 33K IC1002 KIA7042AF R1057 0 ROUT+16V_SC 1 2 G C1366 100pF 50V C1064 0.1uF RHPIN I PVDD_1
24
ROUT+
DDC_SDA_2 100 DDC_SCL_2 0 22 0R 957 CK-_HDMI2 IROUT_HDMI2 HDMI_RX2+ HDMI_RX1+ HDMI_RX0+ HDMI_RX2HDMI_RX1HDMI_RX0HDMI_CLKCEC_REMOTE HDMI_CLK+
23
SE/BTL
WAFER-ANGLE L1002 500-ohm SPK_L+ L1003 500-ohm SPK_LR928 68K A R935 27K MMBD301LT1G SPK_R+ L1004 500-ohm SPK_R0 OPT HDMI_CEC L1009 500-ohm 1 P1001 L1005 500-ohm L1008 500-ohm 2 L1007 500-ohm 3 L1006 500-ohm 4
22
HP/LINE
+3.3V_VDDP_ST
21
VOLUME
SUB_MUTE
R1037 10K
RLINEIN
20
19
SEMAX
D904 30V
R934
VDD
18
AGND
17
BYPASS
R1055 6.8K
S BSS83 Q900 G
BD
R1038 2.2K
16
FADE
0R 950 D2+_HDMI2
R1041 390
LHPIN
10
15
SHUTDOWN
PVDD_2
11
14
LOUTEXT_SPK_L-
12
13
JK901
R1046 1K GND
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
XXLG300C-ZA
2007.08.07
HDMI
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
XXLG300C-ZA
2007.08.07
9 13
+3.3V_VDDP_ST
AUDIO
10
13
22"
P1100 WAFER-STRAIGHT
+3.3V_AVDD_MEMPLL +3.3V_VDDP_ST L1120 MBW3216-501TF +3.3V_VDDP L1125 MBW3216-501TF C1183 0.01uF 50V L1126 MBW3216-501TF C1187 0.01uF 50V C1174 0.1uF 50V +3.3V_VDDP_ST C1192 0.1uF 50V C1188 0.1uF 50V +3.3V_AVDD_DVI
22" IC1200 MP2355DN-LF-Z +5V_ST RUN R1213 10K C1209 2700pF 50V 22" 22" R1214 59K 22" LX 1/16W R1212 6.8K 22" C1210 22uF 16V 22" 22" COMP R1217 10K P_12V
SWITCH +16V/+12V
P_15V
1 C1105 330uF 25V +5V_ST 3 L1102 CB4532UK121E C1117 220uF 16V R1102 0 22" R1116 100 C 22" Q1100 R1104 2SC3052 0 PWM_DIM E C1106 1uF 25V OPT +5V_GENERAL 22" R1109 10K OPT C1107 1uF 25V OPT 4.7K R1114 R1336 0 26"/32"/37"/42" P_12V 26"/32"/37"/42" P1101 SMW200-24C L1131 MLB-201209-0120P-N2 1 LPL37"/CMO26" C1101 0.1uF 16V OPT 0 0 CMO32" +5V_ST C1102 16V 0.1uF OPT 26"/32"/37"/42" 26"/32"/37"/42" R1110 0 3 5 7 9 11 13 15 R1265 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 C1115 0.1uF 16V R1260 68K 26"/32"/37"/42" R1111 0 C1119 100uF 16V C1199 0.1uF 16V +5V A_DIM ** Consider BOOTSTRAP PWM ** C1109 1uF 25V
Stand-by +3.3V_+1.25V_MST_Core
22" R1238 22K R1239 2.2K R1232 10K POWER_ON/OFF1 C1226 4.7uF 16V Q1214
+3.3V_AVDD_MPLL +5V_ST
DC-DC CONVERTER
IC1101 MP2305DS
R1155 100K BS SS C1198 0.1uF 50V
BST
C B E
P_12V 22" C1227 4.7uF 16V
SI4925BDY
+16V
VIN
FB
Q1212 S1 G1 S2 G2
L1204 1 8 D1_2 C1224 100uF 25V L1205 3 6 D2_2 C1225 100uF 16V C1223 0.1uF
+5V_GENERAL +5V_GENERAL
R1118 10K R1120 10K R1119 10K D1102 1N4148W OPT INV_CTL R1121 10K OPT C1196 0.47uF 25V
+3.3V_AVDD_ADC
GND
D1_1
+12V
+1.25V_AVDD_DVI R1134 0
COMP
D2_1
GND
FB
1% 12.4K R1157
IC1102 AZ1085S-ADJTR/E1 INPUT C1128 0.1uF 50V R1128 0 5% 3 1 ADJ/GND R1130 402 R1 1% 2 OUTPUT
A_DIM_1
1%
R1158 33K
EXT_5V/EXT_12V
+1.25V_VDDC C1140 100uF 16V C1143 0.1uF 50V R1133 0 1/4W 5% C1148 0.01uF 50V C1151 0.1uF 50V C1154 10uF 16V 3216 +5V_ST R1205 4.7K EXT5V_DET C R1210 1K 2SA1504S Q1207 C E OPT R1220 0 R1227 11K S C1217 0.1uF 50V OPT R1233 10K R1237 22K +5V_ST OPT R1215 0
L1111 22uH
R2
V0 = 1.25(1+R2/R1) IC1103 AZ1117D-3.3TRE1 INPUT C1126 100uF 16V C1129 0.1uF 50V 3 1 ADJ/GND 2 OUTPUT C1134 100uF 16V C1139 0.1uF 50V +3.3V_TU L1113 MBW3216-501TF C1146 0.1uF 50V AC_DET +16V L1108 MBW3216-501TF C1121 PWM_DIM A_DIM_1 C1123 0.1uF 50V 1 ADJ/GND C1149 100uF 16V C1195 0.1uF 50V C1186 0.01uF 50V C1191 0.1uF 50V +5V_ST OPT R1228 4.7K EXT12V_CTRL R1201 100K 0.01uF 50V C1122 0.1uF 50V +16V_SC L1114 MBW3216-501TF C1147 0.1uF 50V INPUT IC1108 AZ1117D-1.8TRE1 3 2 OUTPUT +1.8V_AMP L1130 MBW3216-501TF +3.3V_AVDD_LPLL P_12V R1200 0 C1202 100pF 50V +3.3V_CI C1184 IC1104 AZ1117D-1.8TRE1 INPUT 3 1 ADJ/GND C1135 100uF 16V 2 OUTPUT L1112 MBW3216-501TF +1.8V_TU 0.01uF 50V L1129 MBW3216-501TF C1145 0.1uF 50V C1189 0.1uF 50V +3.3V_AVDD_AU +5V_ST OPT R1226 4.7K C1190 0.1uF 50V EXT5V_CTRL R1202 100K 5.1V ZD1201
Q1204 2SC3875S E
PWM_DIM
TUNER_CI +3.3V_+1.8V
R1231 4.7K
+3.3V_AVDD_SIF R1218 1K POWER_ON/OFF1 R1203 0 C1204 100pF 50V R1204 10K C B E Q1200 2SC3875S C B E S2 R1207 10K C B C1203 4.7uF 16V +3.3V_AVDD E B C1208 1uF 16V 3 6 D2_2 EXT_12V S1 Q1202 2SC3875S G1 1 8 D1_2 C1212 22uF 16V C1215 0.1uF 50V R1223 10K R1206 10K C1207 1uF 16V R1224 0 EXT_5V EXT12V_CTRL A1
5V_MNT ERROR_OUT
+5V_ST
ZD1203 5.1V
A2
Q1205 SI4925BDY
26"/32"/37"/42" R1262 0
C A2 EXT12V_CTRL
Q1107 2SC3875S
1/4W
POWER_ON/OFF1
26"/32"/37"/42" D1101 A1
R1153 1K
D1_1
+12V RJP
+12V +12V_RJP
G2
+5V_+12V
+12V 26"/32"/37"/42" L1109 MBW3216-501TF +5V_ST L1110 MBW3216-501TF 22" C1131 0.01uF 50V +5V_ST 26" C1136-*1 4.7uF 16V C1132 0.1uF 50V C1110 0.1uF 50V
Q1104 SI4925BDY
Q1201 2SC3875S
+5V_ST
R1222 10K R1225 0 C1216 0.1uF 50V R1230 10K RJP_DET Q1209 RSR025P03 S D C1218 0.1uF 50V R1240 10K L1202 MBW3216-501TF
+12V
+3.3V_MST
+5V C1160 0.1uF 50V +5V_GENERAL C1158 100uF 16V +5V_CI IC1106 AZ1117D-3.3TRE1 INPUT C1161 0.1uF 50V 3 1 ADJ/GND 2 OUTPUT C1176 100uF 16V C1177 0.1uF 50V EXT12V_DET ZD1200 5.1V
DC-DC CONVERTER
+5V_GENERAL
R1219 1K ZD1202 5.1V +5V_ST R1211 4.7K C Q1208 2SA1504S B E R1216 1K OPT R1221 0 C E +5V_ST B R1229 11K
+5V_ST
IC1100 MP2305DS
BS SS R1107 100K OPT C1114 0.1uF 50V
R1125 10K
G1
D1_1
C1159 100uF 16V C1152 100uF 16V L1117 MBW3216-501TF C1163 100uF 16V PANEL_POWER
R1126 EN R1108 1K POWER_ON/OFF1 COMP C1111 5600pF 50V R1113 9.1K 1% 12.4K R1115 L1107 MBW3216-501TF C1116 0.1uF 50V C1118 0.1uF 50V OPT R1123 10K POWER_ON/OFF1 R1122 10K Q1101 2SC3052 B
S2
D2_2
560 C
G2 4 5 D2_1
+2.5V_DDR
C1164 0.1uF 50V +3.3V_VDDP_ST S C1172 0.1uF 50V OPT R1141 0 IC1107 AZ1117D-2.5TRE1 D C1175 0.1uF 50V INPUT 3 1 OPT R1159 10K G C1178 10uF 16V R1139 0 ADJ/GND OPT R1140 C1193 100uF 16V C1194 0.1uF 50V 2 OUTPUT +2.5V_DDR 1/4W 5% Q1105 RSR025P03 OPT R1208 0
Q1206 2SC3875S
R1235 4.7K
E +5V_TU
GND
FB
R1127 22K
R1131 10K
22"
56K R1105
1%
B C
Q1103 2SC3052
L1105 22uH
PANEL_CTL
B R1124 10K E
Q1102 2SC3052
DDR_PWR_CTRL
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
XXLG300C-ZA EXT-Power
2007.10.27 12 13
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
XXLG300C-ZA
2007.08.07
Power
11 13
LGE Internal Use Only
P/NO : MFL39166103