Documente Academic
Documente Profesional
Documente Cultură
ANALYSIS / COMPARATIVE STUDY OF EXISTING 25+4.0m Extended Latticed MONOPOLE TOWER (LTE Project 2011)
ZND090
ZND090-AMT-Td-0001 Rev.A
COVER PAGE TABLE OF CONTENTS INTRODUCTION CONCLUSION TOWER COMPARATIVE STUDY TABLE I - WIND LOAD ON ANTENNA SUPPORT PIPE AND OTHER MOUNTED POLE STRUCTURE
TABLE II - STANDARD 25m SELF-SUPPORT MONOPOLE WIND LOAD
1 2 3 3 4 6 7 8 9
TOWER DEFLECTION TOWER INFORMATION ATTACHMENT ORIGINAL TOWER LOAD DESIGN CALCULATION TOWER PROFILE
Analyzed by:
Checked by:
Approved by:
Page 2 of 11
ZND090-AMT-Td-0001 Rev.A
ZND090
INTRODUCTION
Tower load comparative study for main site no. ZND090 was performed to compare the design load against the actual load to determine its feasibility to support the existing and the proposed new antenna loading to be used for LTE Project 2011. Refer to pages 4 to 7 for the detailed comparative study of the tower original design loading and actual loading. Tower existing loading condition and proposed new antennas and tower physical condition and other relevant information are tabulated on pages 9 to 11. For information on tower mast geometry and member sizes, see attachment.
CONCLUSION
The results show that the tower meet the criteria of 39 m/s (140KPH) basic wind speed. The original design load of the tower is greater than the present actual load and it is indicative that there is no increase in antenna loads. Hence, we can conclude that the tower can safely support the existing and the proposed microwave antenna loading for LTE Project 2011 .
Page 3 of 11
ZND090-AMT-Td-0001 Rev.A
Comparison between original design loads and actual loads for standard 25.0m Monopole tower
Tower height = Gh =
25 m 1.690
Dept
Qty, n
Elevation (m)
25.0 25.0 25.0 N/A 4 N/A 4 N/A 4
Kz
1.299 1.299 1.299 1.000 1.000 1.000
Fa (kN)
0.89 1.39 5.56 N/A 4 N/A 4 N/A 4
Fa*Gh*Kz*n (kN)
17.51 6.10 12.21 N/A 4 N/A 4 N/A 4
5672.52
1 25.0m high Monopole Tubular Pole 2 2.0 m high Mounted Pole 3 4.0m high Cantileverd Lattice 4 Previously gusted (i.e. K Z and Gh equal to 1.0), see Tables I, II & III
Page 4 of 11
ZND090-AMT-Td-0001 Rev.A
Kz
1.3687 1.3555 1.3420 1.3139 1.2842 1.2992 1.2992 1.2842 1.2687 1.2687 1.2607 1.2687
1.314 1.000 1.000 1.000
Dept
GSM GSM MW GSM MW GSM GSM MW MW MW MW MW GSM GSM GSM GSM
Fa (kN)
0.016 0.713 0.120 0.534 0.120 0.713 0.538 0.120 0.350 0.120 0.120 0.120 0.538 N/A 2 N/A 2 N/A 2
900 MHZ 0.30 DIA. 1800 MHZ 0.30 DIA. 900 MHZ 2100 MHZ 0.30 DIA. 0.60 DIA. 0.30 DIA. 0.30 DIA. 0.30 DIA.
25.0m high 2.0M high 4.0m high
30 29 28 26 24 25 25 24 23 23 22.5 23
26.00 N/A 2 N/A 2 N/A 2
Total Base Moment = % Comparison of original design loads versus actual loads =
1 2
4267.11 0.7522
New GSM antenna Previously gusted (i.e. K Z and Gh equal to 1.0), see Tables I & II
Conclusion : Since there is no increase in antenna loads, therefore the tower can safely support the existing plus the proposed new loading.
Page 5 of 11
ZND090-AMT-Td-0001 Rev.A
Table I - Wind load on antenna support pipe and other mounted pole & latticed structures.
Tower ht. = Wind speed = Gh1 =
Actual Loads
25 m 39 m/s
1.5625 1.00 </=GH</=1.25 Sec.2.3.4.1 of TIA-EIA-222-F
Size
Dept
Kz
CF (C<4.40)
LR
20mmx2.0m
GSM
2000
29.80
1.366
0.912
1.200
multiplied by 1.25, to compensate for the greater gust response for mounted pole structure (EIA/TIA-222-E, Sec. 2.3.4.4)
Table I - Wind load on antenna support pipe and other mounted pole structures.
Tower ht. = Wind speed = Gh1 =
Actual Loads
25 m 35 m/s
1.5625 1.00 </=GH</=1.25 Sec.2.3.4.1 of TIA-EIA-222-F
Size
Dept
Length, l Diameter, d Appurtenance (mm) (mm) 20.0 c/l Elev., (m) 29.80
Kz
CF (C<4.40)
LR
20mmx2.0m
GSM
2000
1.365
0.818
1.200
multiplied by 1.25, to compensate for the greater gust response for mounted pole structure (EIA/TIA-222-E, Sec. 2.3.4.4)
ZND090-AMT-Td-0001 Rev.A
Total Base Moment = 1042.59
Page 7 of 11
LTE Project 2011 TABLE II - 25.0M SELF-SUPPORTING MONOPOLE TOWER Typical tower wind load distribution as per section in normal to the tower face.
H= V= GH = 25
39 1.69 m m/s
ZND090-AMT-Td-0001 Rev.A
Heightof Monopole
SECTION 1 2 3
F=qz*GH*CF*AR(kNs) GH*qZ*AG zequivalent(m) OTM(kN-m) 18456.99 130.95 20.482 2682.12 17668.57 140.46 11.520 1618.10 14372.05 97.22 3.458 336.187 Total =
4636.41
kN-m
TABLE II - 25.0M SELF-SUPPORTING MONOPOLE TOWER Typical tower wind load distribution as per section in normal to the tower face.
H= V= GH = 25 m
m/s
Heightof Monopole
35
1.69
SECTION 1 2 3
F=qz*GH*CF*AR(kNs) GH*qZ*AG zequivalent(m) OTM(kN-m) 14865.10 105.47 20.482 2160.24 14230.11 113.12 11.520 1303.14 11575.13 78.30 3.458 270.761 Total =
3734.14
kN-m
MT-Td-0001 Rev.A
ZND090-AMT-Td-0001 Rev.A
ELEV. (m)
36.00
79.70
0.24
44.00
0.13
0.50
The above shown tower deflection is based on the original design loads (attached); considering that the existing + proposed antenna loads are less than the original design loads, thus actual tower deflection will be lesser than the deflection due to original design loads.
Page 8 of 11
Page 8 of 11
ZND090-AMT-Td-0001 Rev.A
Page 9 of 11
ZND090-AMT-Td-0001 Rev.A
NOTES:
ANTENNA DATA: No. Assign a number to each antenna, starting at top of tower and working down. TYPE Paraboloid (Dish): S- Solid, G- Grid, HP- High Performance (Flat Shielded), R- with Radome T.V.- UHF, BC- Broadcast, Y- Yagi, D- Directional (cellular), O- Omnidirectional, P- Paging Reflectors: CHR- Conical Horn Reflector, FPR- Flat Plate Passive Reflectors. G.S.M.: A- ALLGON, ADC- ADC Dual Polarized. MISC.: S/S- Self Supporting Tower, G/T- Guyed Tower, P/M- Pole Mount. SIZE: Indicate diameter in meters for parabolic (microwave dishes), size for other types. ELEV. Height above ground in meters (Elevation). AZIM. Azimuth: Show antenna orientation in degrees or compass reading (N, NE, E,SE, S, etc.). F/L Indicate antenna mount: Face (F) or leg (L). REMARKS Existing or proposed new antenna(s) designation. FEEDLINES/ LADDER DATA QTY: Quantity. SIZE: Diameter or size in (mm). TYPE: W- Waveguide, C- Coax, H- Heliax, L- Ladder. COMMENTS
Page 10 of 11
ZND090-AMT-Td-0001 Rev.A
NOTES:
ANTENNA DATA: No. Assign a number to each antenna, starting at top of tower and working down. TYPE Paraboloid (Dish): S- Solid, G- Grid, HP- High Performance (Flat Shielded), R- with Radome T.V.- UHF, BC- Broadcast, Y- Yagi, D- Directional (cellular), O- Omnidirectional, P- Paging Reflectors: CHR- Conical Horn Reflector, FPR- Flat Plate Passive Reflectors. G.S.M.: A- ALLGON, ADC- ADC Dual Polarized. MISC.: S/S- Self Supporting Tower, G/T- Guyed Tower, P/M- Pole Mount. SIZE: Indicate diameter in meters for parabolic (microwave dishes), size for other types. ELEV. Height above ground in meters (Elevation). AZIM. Azimuth: Show antenna orientation in degrees or compass reading (N, NE, E,SE, S, etc.). F/L Indicate antenna mount: Face (F) or leg (L). REMARKS Existing or proposed new antenna(s) designation. FEEDLINES/ LADDER DATA QTY: Quantity. SIZE: Diameter or size in (mm). TYPE: W- Waveguide, C- Coax, H- Heliax, L- Ladder. COMMENTS
Page 10A of 11
ZND090-AMT-Td-0001 Rev.A
None 36.0 M
Tower Base outside width 6.70 m Tower Type Tower Cross-Section Tower Members 25 dia. mm x Self Supporting Triangular Tubular Angle Solid Rd Anchor Bolt Size BasePlate Thickness 4.0 cm Guyed Mast x Rectangular Legs x BasePlate dimensions 40x40 cm Monopole Diagonals x Struts x Tower Conditions: Guy Wires Structural x Good, no visible rust or kinks, straight members Yes No Average, some surface rust, no other damage x Ladder Exists Below Average, rusty, needs maintenance x Enclosed Ladder Poor, severe rust, bent/ missing members, bolts or strands x Painted Red/White, No. of bands 7 Loose or corroded bolts or anchor bolts or Guy Hardware Sagging Guy wires, Tower Out of Plumbness or Twisted Foundation Type Condition Cement Grout Piers x Good, no visible cracks or damage x Good x Raft Average, edges rough, no cracks, edge wear Fair Piles Below Average, surface cracks, edge wear Poor, missing Roof Mount Poor cracks, spalding, deteriorating Others Guy Anchor Size N/A . x Pedestal Size 70 x 70 cm Distance from tower to anchor block N/A Comments :
Page 11 of 11