Documente Academic
Documente Profesional
Documente Cultură
633204
Fly
WORKSHOP MANUAL
Fly
The descriptions and illustrations given in this publication are not binding. While the basic specifications as described and illustrated in this manual remain unchanged, PIAGGIO-GILERA reserves the right, at any time and without being required to update this publication beforehand, to make any changes to components, parts or accessories, which it considers necessary to improve the product or which are required for manufacturing or construction reasons. Not all versions/models shown in this publication are available in all countries. The availability of each model should be checked at the official Piaggio sales network. " Copyright 2008 - PIAGGIO & C. S.p.A. Pontedera. All rights reserved. Reproduction of this publication in whole or in part is prohibited." PIAGGIO & C. S.p.A. - After sales V.le Rinaldo Piaggio, 23 - 56025 PONTEDERA (Pi)
WORKSHOP MANUAL
Fly
This workshop manual has been drawn up by Piaggio & C. Spa to be used by the workshops of PiaggioGilera dealers. This manual is addressed to Piaggio service mechanics who are supposed to have a basic knowledge of mechanics principles and of vehicle fixing techniques and procedures. Any important changes made to the vehicles or to specific fixing operations will be promptly reported by updates to this manual. Nevertheless, no fixing work can be satisfactory if the necessary equipment and tools are unavailable. It is therefore advisable to read the sections of this manual relating to specific tools, along with the specific tool catalogue.
N.B. Provides key information to make the procedure easier to understand and carry out.
CAUTION Refers to specific procedures to carry out for preventing damages to the vehicle.
WARNING Refers to specific procedures to carry out to prevent injuries to the repairer.
Personal safety Failure to completely observe these instructions will result in serious risk of personal injury.
Safeguarding the environment Sections marked with this symbol indicate the correct use of the vehicle to prevent damaging the environment.
Vehicle intactness The incomplete or non-observance of these regulations leads to the risk of serious damage to the vehicle and sometimes even the invalidity of the guarantee.
INDEX OF TOPICS
CHARACTERISTICS TOOLING MAINTENANCE TROUBLESHOOTING ELECTRICAL SYSTEM ENGINE FROM VEHICLE ENGINE SUSPENSIONS BRAKING SYSTEM CHASSIS PRE-DELIVERY TIME
CHAR TOOL MAIN TROUBL ELE SYS ENG VE ENG SUSP BRAK SYS CHAS PRE DE TIME
INDEX OF TOPICS
CHARACTERISTICS
CHAR
Fly
Characteristics
Rules
This section describes general safety rules for any maintenance operations performed on the vehicle.
Safety rules
- If work can only be done on the vehicle with the engine running, make sure that the premises are wellventilated, using special extractors if necessary; never let the engine run in an enclosed area. Exhaust fumes are toxic. - The battery electrolyte contains sulphuric acid. Protect your eyes, clothes and skin. Sulphuric acid is highly corrosive; in the event of contact with your eyes or skin, rinse thoroughly with abundant water and seek immediate medical attention. - The battery produces hydrogen, a gas that can be highly explosive. Do not smoke and avoid sparks or flames near the battery, especially when charging it. - Fuel is highly flammable and it can be explosive given some conditions. Do not smoke in the working area, and avoid naked flames or sparks. - Clean the brake pads in a well-ventilated area, directing the jet of compressed air in such a way that you do not breathe in the dust produced by the wear of the friction material. Even though the latter contains no asbestos, inhaling dust is harmful.
Maintenance rules
- Use original PIAGGIO spare parts and lubricants recommended by the Manufacturer. Non-original or non-conforming spare parts may damage the vehicle. - Use only the appropriate tools designed for this vehicle. - Always use new gaskets, sealing rings and split pins upon refitting. - After removal, clean the components using non-flammable or low flash-point solvents. Lubricate all the work surfaces, except tapered couplings, before refitting these parts. - After refitting, make sure that all the components have been installed correctly and work properly. - For removal, overhaul and refit operations use only tools with metric measures. Metric bolts, nuts and screws are not interchangeable with coupling members with English measurement. Using unsuitable coupling members and tools may damage the vehicle. - When carrying out maintenance operations on the vehicle that involve the electrical system, make sure the electric connections have been done properly, particularly the ground and battery connections.
CHAR - 7
Characteristics
Fly
Vehicle identification
VEHICLE IDENTIFICATION
Specification Frame prefix Engine prefix Desc./Quantity ZAPM44100 1001 C441M 1001
CHAR - 8
Fly
Characteristics
Engine
ENGINE
Specification Engine type Bore x stroke Cubic capacity Compression ratio Carburettor CO adjustment Engine idle speed Air filter Starting system Lubrication Desc./Quantity Two-stroke, single cylinder Piaggio Hi-PER2 40 X 39.3 mm 49.40 cc 10,3 :1 DELL'ORTO PHVA 17.5 3.5% 0.5 1800 to 2000 r.p.m. Sponge, soaked in a mixture (50% SELENIA Air Filter Oil and 50% unleaded petrol). electric starter/kick-starter With blend and variable oil variable according to the engine revolutions and the throttle valve opening by means of a pump controlled by the driving shaft with toothed belt. Gravity feed, with unleaded petrol (with a minimum octane rating of 95) with carburettor. forced coolant circulation system
CHAR - 9
Characteristics
Fly
Transmission
TRANSMISSION
Specification Transmission Desc./Quantity With automatic expandable pulley variator, torque server, Vbelt, automatic clutch, gear reduction unit.
Capacities
CAPACITIES
Specification Rear hub oil oil mixer tank Fuel tank capacity Desc./Quantity Quantity: approx. 85 cc Plastic, capacity ~ 1.2 l approx. 7.2 litres (of which 1.5 l is reserve)
Electrical system
ELECTRICAL SYSTEM
Specification Type of ignition Ignition advance (before TDC) Recommended spark plug Battery Main fuse Generator Desc./Quantity Capacitive discharge type electronic ignition, with incorporated high voltage coil Fixed 17 1 CHAMPION RN2C 12V-4Ah 7.5 A In alternate current with three output sections
Brakes
FRENI
Specification Front brake Rear brake Desc./Quantity Disc brake ( 200 mm) with hydraulic control (lever on the right end of the handlebar) and floating calliper. drum brake ( 140 mm) with mechanical linkage.(l.h. brake lever).
CHAR - 10
Fly
Characteristics
Specification Rear wheel rim Rear tyre Front tyre pressure Rear tyre pressure Rear wheel pressure (rider and passenger):
Desc./Quantity Die-cast aluminium alloy: 3.00"x12" Tubeless, 120/70 - 12" 1.8 bar 2 bar 2.3 bar
Secondary air
Follow these steps to clean the sponge filters of the secondary air system: 1) Remove the snap-on plastic cover (1) on the transmission cover using a small screwdriver as a lever on the retaining tongues in order to insert one of the three slots found on that cap. 2) Wash the polyurethane sponge with water and soap, dry all components with compressed air and refit to place. Refit the intake cap respecting the angle reference. 3) Undo the two fixing screws (2) on the aluminium cover of the secondary air housing in order to reach the polyurethane sponge inside that housing; clean as indicated in point 2) and refit all elements after checking the steel tab is not deformed and/or does not guarantee correct tightness at its fitting; replace if necessary.
N.B. UPON REFITTING, MAKE SURE TO CORRECTLY FIT THE TAB IN ITS FITTING ON THE TWO PLASTIC AND ALUMINIUM COVERS. CAUTION WHILE CARRYING OUT OPERATION 3), ALWAYS CHECK THE TWO RUBBER COUPLINGS (3) ON ONE END OF THE SECONDARY AIR PIPE FOR CORRECT TIGHTNESS AND CONTINUITY; IF NECESSARY, REPLACE THEM AND USE NEW CLAMPS TO FIX THEM.
CHAR - 11
Characteristics
Fly
Dell'Orto
DELLORTO CARBURETTOR
Specification Type Diffuser diameter Regulation reference number Maximum nozzle: Maximum air nozzle (on the body): Tapered pin stamped code: Pin position (notches from above): Diffuser: Minimum nozzle: Minimum air nozzle (on the body): Initial minimum mix screw opening: Starter jet Starter air nozzle (on the body): Stroke of starter pin: Gasoline inlet hole Desc./Quantity PHVA 17.5 RD 17.5 8423 53 1.5 A22 1 209 HA 32 Free 1 1/2 50 1.5 11 mm 1.5
Tightening Torques
FRONT BRAKE
Name Brake fluid pump - hose fitting Brake fluid pipe-calliper fitting Calliper tightening screw Disc tightening screw Oil bleed screw Torque in Nm 16 20 Nm 19 24 24 27 8 10 7 10
FRONT SUSPENSION
Name Lower fork fixing screw Front wheel axle nut Torque in Nm 15 20 45 - 50
STEERING ASSEMBLY
Name Upper steering ring nut Steering lower ring nut Handlebar fixing screw Torque in Nm 35 40 8 10 50 55
ENGINE ASSEMBLY
Name Clutch bell nut (**) Clutch lock ring nut Nut locking driving pulley on crankshaft (**) Start-up lever screw Flywheel nut (**) Flywheel fan screws Half-crank case joint bolts Bolts holding exhaust pipe to the crankcase Screws holding the filter box to the crank case Head nuts Starter screws Ignition spark plug Hub oil drainage cap Oil hub level dipstick Rear hub cap screws Transmission cover screws Inlet manifold screws Torque in Nm 40 44 55 60 40 44 Nm 12 13 40 44 34 12 13 22 24 45 10 11 12 13 25 30 35 Manual 12 13 12 13 89
CHAR - 12
Fly
Characteristics
Name Flywheel hood fixing screws Cylinder hood fixing screws Stator clamping screws Pick-Up clamping screw Mixer clamping screws Screw fixing brake lever to the journal on the engine
Torque in Nm 12 3.5 5 34 45 34 12 13
CHASSIS
Name Swinging arm - engine pin* Frame/swing-arm bolt (*) Shock absorber - chassis nut (*) shock absorber - engine pin (*) Rear wheel axle (*) Centre-stand mounting bracket bolt Centre-stand mounting bracket screw Side stand fixing screw Side stand bracket fixing screw Torque in Nm 33 41 6472 20 to 25 Nm 33 to 41 Nm 104126 Nm 2530 Nm 2025 Nm 12 20 15 20
CHAR - 13
Characteristics
Fly
Piston rings
SEALING RING
Name Compression ring Compression ring 1st oversize Compression ring 2nd Oversize Description Dimensions 40 40.2 40.4 Initials A A A Quantity 0.10 to 0.25 0.10 to 0.25 0.10 to 0.25
13.75+0.040
13.75+0.040
40.64
11.800-0.35
Fly
Characteristics
For 25 km/h engine type versions, use 2 gaskets between cylinder and crankcase.
Products
RECOMMENDED PRODUCTS TABLE
Product AGIP ROTRA 80W-90 AGIP CITY HI TEC 4T Specifications SAE 80W/90 Oil that exceeds the requirements of API GL3 specifications Oil to lubricate flexible transmissions Oil for 2-stroke engines: SAE 5W-40, API (brake, throttle control and mixer, odomSL, ACEA A3, JASO MA eter) Oil for air filter sponge Mineral oil with specific additives for increased adhesiveness Mixer oil synthetic oil for 2-stroke engines: JASO FC, ISO-L-EGD Brake fluid FMVSS DOT 4 Synthetic fluid Grease for driven pulley shaft adjusting Grease with Molybdenum disulphide ring and movable driven pulley housing Grease for steering bearings, pin seats White anhydrous-calcium based grease and swinging arm to protect roller bearings; temperature range between -20 C and +120 C; with NLGI 2; ISO-L-XBCIB2. Grease for odometer transmission gear Lithium grease with NLGI 2 molybdenum case disulphide; ISO-L-XBCHB2, DIN KF2K-20 Grease for brake control levers, throttle, White calcium complex soap-based stand spray grease with NLGI 2; ISO-L-XBCIB2 Description Rear hub oil
AGIP FILTER OIL AGIP CITY TEC 2T AGIP BRAKE 4 MONTBLANC MOLYBDENUM GREASE AGIP GREASE PV2
AGIP GREASE SM 2
AGIP GP 330
CHAR - 15
INDEX OF TOPICS
TOOLING
TOOL
Fly
Tooling
TOOLS
Stores code 001330Y Description Tool for fitting steering seats
001467Y006
001467Y007
001467Y009
001467Y013
001467Y014
TOOL - 17
Tooling
Fly
001467Y021
002465Y
006029Y
020004Y
020055Y
020150Y
TOOL - 18
Fly
Tooling
020162Y
Flywheel extractor
020163Y
020164Y
020165Y
020166Y
TOOL - 19
Tooling
Fly
020262Y
020265Y
020325Y
020329Y
020330Y
TOOL - 20
Fly
Tooling
020332Y
020333Y
020334Y
TOOL - 21
Tooling
Fly
020350Y
020357Y 020359Y
020376Y
Adaptor handle
020412Y
15-mm guide
TOOL - 22
Fly
Tooling
Description 24 mm adaptor
020483Y
30-mm guide
020565Y
494929Y
TOOL - 23
INDEX OF TOPICS
MAINTENANCE
MAIN
Fly
Maintenance
Maintenance chart
EVERY 2 YEARS
Action Brake fluid - change
AFTER 1000 KM
50'
Action Hub oil - change Oil mixer/throttle linkage - adjustment Odometer gear - greasing Steering - adjustment Brake control levers - greasing Brake fluid level - check Safety locks - check Electrical system and battery - check Tyre pressure and wear - check Vehicle and brake test - road test
Maintenance
Fly
Action Hub oil level - check Spark plug/electrode gap - replacement Air filter - cleaning Oil mixer/throttle linkage - adjustment Driving belt - replacement Brake control levers - greasing Brake pads - check condition and wear Brake fluid level - check Electrical system and battery - check Tyre pressure and wear - check SAS box (sponge) (**) - cleaning Vehicle and brake test - road test (**) See regulations in the Secondary air system section
AFTER 30000 KM
130'
Action Hub oil - change Spark plug/electrode gap - replacement Air filter - clean Idling speed (*) - adjustment Oil mixer/throttle linkage - adjustment Driving belt - replacement Variable speed rollers - replacement Odometer gear - greasing Steering - adjustment Brake control levers - greasing Brake pads - check condition and wear Flexible brake tubes - replacement Brake fluid level - check Transmission elements - lubrication Safety locks - check Suspensions - check Electrical system and battery - check Headlight - adjustment Tyre pressure and wear - check SAS box (sponge) (**) - cleaning Vehicle and brake test - road test
MAIN - 26
Fly
Maintenance
(*) See regulations in the Adjusting the idle speed section (**) See regulations in the Secondary air system section
AFTER 60000 KM
150'
Action Hub oil - change Spark plug/electrode gap - replacement Air filter - clean Idling speed (*) - adjustment Cylinder cooling system - check/cleaning Oil mixer/throttle linkage - adjustment Driving belt - replacement Variable speed rollers - replacement Mixer belt - replacement Odometer gear - greasing Steering - adjustment Brake control levers - greasing Brake pads - check condition and wear Flexible brake tubes - replacement Brake fluid level - check Transmission elements - lubrication Safety locks - check Suspensions - check Electrical system and battery - check Headlight - adjustment Tyre pressure and wear - check SAS box (sponge) (**) - cleaning Vehicle and brake test - road test (*) See regulations in the Adjusting the idle speed section (**) See regulations in the Secondary air system section
Carburettor
- Disassemble the carburettor in its parts, wash all of them with solvent, dry all body grooves with compressed air to ensure adequate cleaning. - Check carefully that the parts are in good condition. -The throttle valve should move freely in the chamber. Replace valve in case of wear due to excessive clearance. - If there are wear marks in the chamber causing inadequate tightness or a free valve slide (even if it is new), replace the carburettor. - It is advisable to replace the gaskets at every refit.
WARNING PETROL IS HIGHLY EXPLOSIVE ALWAYS REPLACE THE GASKETS TO AVOID PETROL LEAKS
MAIN - 27
Maintenance
Fly
1. Automatic starter - 2. Idle air set screw - 3. Idle speed set screw - 4. Throttle valve spring - 5. Throttle valve tapered pin - 6. Throttle valve - 7. Carburettor body - 8. Pin - 9. Min. jet - 10. Float - 11. Max. jet - 12. Float chamber
Specific tooling
020330Y Stroboscopic light to check timing
Spark plug
Place the vehicle on its central stand - Remove the central cover, indicated in the figure, by undoing the 2 fixing screws; - Disconnect spark plug HV wire hood; -Undo the spark plug using the socket wrench; -Examine the condition of the spark plug, check that the insulating material is whole and measure the distance between the electrodes using a thickness gauge. -Adjust the distance if necessary by bending the side electrode very carefully. In the case of defects, replace the spark plug with one of the specified type;
MAIN - 28
Fly
Maintenance
- Engage the spark plug with the due inclination and screw it right down by hand, then do it up with the wrench at the prescribed torque; -Put the hood on the sparking plug as far as it will go; - Refit the central flap.
CAUTION THE SPARK PLUG MUST BE REMOVED WHEN THE MOTOR IS COLD. THE SPARK PLUG MUST BE REPLACED EVERY 5000 KM. USE OF STARTERS NOT CONFORMING OR SPARK PLUGS NOT THOSE DESCRIBED CAN SERIOUSLY DAMAGE THE ENGINE.
Characteristic
Recommended spark plug CHAMPION RN2C
Electric characteristic
Electrode gap 0.6 to 0.7 mm.
Recommended products
AGIP ROTRA 80W-90 Rear hub oil SAE 80W/90 Oil that exceeds the requirements of API GL3 specifications
MAIN - 29
Maintenance
Fly
Replacement
- Remove the oil filler cap A. - Loosen the oil draining cap B and let the oil completely drain the tank. - Tighten the draining cap and refill the hub with oil (approx. 75 cc).
Air filter
-Remove the cap of the purifier, unscrewing the six clamping screws and removing the filter. Cleaning: -Wash with water and neutral soap. - Dry with a clean cloth and short blasts of compressed air. -Saturate with a 50% mixture of gasoline and oil. -Drip dry the filter and then squeeze it between the hands without wringing. -Let it dry and refit it again.
CAUTION NEVER RUN THE ENGINE WITHOUT THE AIR FILTER, THIS WOULD RESULT IN AN EXCESSIVE WEAR OF THE PISTON AND CYLINDER.
Recommended products
AGIP FILTER OIL Oil for air filter sponge Mineral oil with specific additives for increased adhesiveness
MAIN - 30
Fly
Maintenance
Recommended products
AGIP CITY TEC 2T Mixer oil synthetic oil for 2-stroke engines: JASO FC, ISOL-EGD
Braking system
MAIN - 31
Maintenance
Fly
Level check
Proceed as follows: - Rest the vehicle on its centre stand with the handlebars perfectly horizontal; - Check the level of liquid with the related warning light A. A certain lowering of the level is caused by wear on the pads.
Top-up
Proceed as follows: - Remove the tank cap by loosening the two screws, remove the gasket and top up using only the liquid specified without exceeding the maximum level.
CAUTION ONLY USE DOT 4-CLASSIFIED BRAKE FLUID. CAUTION
AVOID CONTACT OF THE BRAKE FLUID WITH YOUR EYES, SKIN, AND CLOTHING. IN CASE OF ACCIDENTAL CONTACT, WASH WITH WATER. CAUTION BRAKING CIRCUIT FLUID IS HIGHLY CORROSIVE; MAKE SURE THAT IT DOES NOT COME INTO CONTACT WITH THE PAINTWORK. CAUTION THE BRAKE FLUID IS HYGROSCOPIC, IN OTHER WORDS, IT ABSORBS MOISTURE FROM THE SURROUNDING AIR. IF THE CONTENT OF MOISTURE IN THE BRAKING FLUID EXCEEDS A CERTAIN VALUE, BRAKING WILL BE INEFFICIENT. NEVER USE BRAKE LIQUID IN OPEN OR PARTIALLY USED CONTAINERS. UNDER NORMAL CLIMATIC CONDITIONS, THE FLUID MUST BE CHANGED EVERY 20,000 KM OR ANYWAY EVERY TWO YEARS. N.B. SEE THE BRAKING SYSTEM CHAPTER WITH REGARD TO THE CHANGING OF BRAKE FLUID AND THE BLEEDING OF AIR FROM THE CIRCUITS.
Recommended products
AGIP BRAKE 4 Brake fluid FMVSS DOT 4 Synthetic fluid
MAIN - 32
Fly
Maintenance
Headlight adjustment
Proceed as follows: 1. Place the vehicle, in running order and with the tyres inflated to the prescribed pressure, on a flat surface 10-m away from a white screen situated in a shaded area, making sure that the longitudinal axis of the scooter is perpendicular to the screen; 2. Turn on the headlight and check that the borderline of the projected light beam on the screen is not higher than 9/10 or lower than 7/10 of the distance from the ground to the centre of vehicle headlamp; 3. If otherwise, adjust the right headlight with screw A.
N.B. THE ABOVE PROCEDURE COMPLIES WITH THE EUROPEAN STANDARDS REGARDING MAXIMUM AND MINIMUM HEIGHT OF LIGHT BEAMS. REFER TO THE STATUTORY REGULATIONS IN FORCE IN EVERY COUNTRY WHERE THE VEHICLE IS USED.
CO check
In the event that the exhaust on the vehicle being tested does not have an exhaust gases collection port, proceed as follows: - Remove the R.H. side fairing - Remove the secondary air box cover with the aluminium cap by acting upon the clamp shown in the figure.
Attach the exhaust gas collection tube to the secondary air rubber manifold. Such joint must be sealed in order to guarantee accurate CO readings.
- Start the engine, adjust the idle speed to 1,700 100 rpm and check the CO value is equal 3.5 1% MAIN - 33
Maintenance
Fly
- If the parameters found do not agree with the above figures, act upon the idle adjusting screw. Otherwise, check the automatic choke device
Specific tooling
020320Y Exhaust gases analyser 020332Y Digital rpm indicator
The check must be carried out after having carefully cleaned all carburettor components, with the air filter clean, and the spark plug in good conditions. - Remove the R.H. side fairing - Warn-up the engine by riding the vehicle on the road for at least 10 minutes - Shut down the engine - Remove the 2 secondary air box screws shown in the figure Place a plastic sheet between the one-way valve and the aluminium outlet as shown in the figure
Ensure the one-way valve packing properly seals the aluminium outlet fitting. Refit the aluminium outlet onto the SAS box as shown in the picture.
MAIN - 34
Fly
Maintenance
- Attach the special tool and move the joints as shown in the figure. - Start the engine, adjust the idle speed to 1,700 100 rpm and check the CO value is equal 3.5 1% - If the parameters found do not agree with the above figures, act upon the idle adjusting screw. Otherwise, check the automatic choke device.
Specific tooling
020320Y Exhaust gases analyser 020332Y Digital rpm indicator 020625Y Kit for sampling gas from the exhaust manifold
MAIN - 35
INDEX OF TOPICS
TROUBLESHOOTING
TROUBL
Fly
Troubleshooting
This section makes it possible to find the solutions to use in troubleshooting. For each breakdown, a list of the possible causes and respective interventions is given.
Driving belt worn Carburettor nozzles clogged Fuel filter on vacuum operated cock blocked Roller wear; Presence of oil; Dirt
Starting difficulties
DIFFICULTY STARTING
Possible Cause Carburettor nozzles clogged or dirty Faulty fuel cock Operation Dismantle, wash with solvent and dry with compressed air Check that, at ignition and with throttle untwisted, no petrol flows out the delivery pipe; otherwise, replace the vacuum-operated cock Check: electric wiring, circuit continuity, mechanical sliding and power supply Check and if necessary replace the spark plug and the electrode gap Check the state of the battery. If it shows signs of sulphation replace it and bring the new battery into service charging it for eight hours at a current of 1/10 of the capacity of the battery itself Start the vehicle keeping the throttle fully open alternately making the engine run for approx. five seconds and stopping for other five seconds. If however it does not start, remove the spark plug, the engine over with the throttle open being careful
Starter inefficient Defective spark plug or with incorrect electrode gap Battery flat
- Engine flooded.
TROUBL - 37
Troubleshooting
Fly
Possible Cause
Operation to keep the cap in contact with the spark plug and the spark plug grounded but away from its hole. Refit a dry spark plug and start the vehicle. Drain off the fuel no longer up to standard; then, refill Remove the encrustation, restore the plug gap or replace being sure to use the types of spark plug recommended at all times. Bear in mind that many problems engines have, derive from the use of the wrong spark plug Replace intake joint and check for correct sealing on the head Replace
TROUBL - 38
Fly
Troubleshooting
SAS malfunctions
SLACKENING OF THE RUBBER JOINT OF THE SECONDARY AIR PIPE ON THE MUFFLER
Possible Cause Secondary air reed blocking Secondary air filter clogging Blockage of the secondary air fitting on the muffler Operation Replace Clean the filter and the housing Remove the encrustations from the joint being careful not to let the debris fall into the muffler
Insufficient braking
BRAKING SYSTEM MALFUNCTION
Possible Cause Poor braking Operation The rear (drum type) brake is adjusted by regulating the special adjustment (on the wheel) bearing in mind that, with the control levers in the rest position, the wheels must turn freely. The braking action should begin when the brake levers are pressed by about a third. Check the brake pad wear. If it is not possible to remove any problems by simply adjusting the transmissions, check the brake pads and front brake disc, the brake shoes and the rear drum. If you encounter excessive wear or scoring, make the necessary replacements. Carefully bleed the hydraulic braking system, (there must be no flexible movement of the brake lever). Elastic fittings, piston seals or brake pump breakdown, replace Replace the front brake fluid and top up to the correct level in the pump Lubricate or substitute Check the wear of the brake pads and/or shoes
Air bubbles inside the hydraulic braking system Fluid leakage in hydraulic braking system The brake fluid has lost its properties Defective sliding of the cables in their sheathes Brake noise
TROUBL - 39
Troubleshooting
Fly
Brakes overheating
BRAKES OVERHEATING
Possible Cause Defective piston sliding Brake disc or drum deformed Operation Check calliper and replace any damaged part. Using a dial gauge, check the planarity of the disk with the wheel correctly fitted or the concentricity of the rear drum.
Heavy steering
STEERING HARDENING
Possible Cause Torque not conforming Operation Check the tightening of the top and bottom ring nuts. If irregularities continue in turning the steering even after making the above adjustments, check the seats in which the ball bearings rotate: replace if they are recessed.
TROUBL - 40
Fly
Troubleshooting
Noisy suspension
NOISY SUSPENSION
Possible Cause NOISY SUSPENSION Operation If the front suspension is noisy, check: the efficiency of the front shock absorbers; the condition of the ball bearings and relevant lock-nuts, the limit switch rubber buffers and the movement bushings.
TROUBL - 41
INDEX OF TOPICS
ELECTRICAL SYSTEM
ELE SYS
Fly
Electrical system
1 2 3 4 5 6 7 8 9 10 11
Specification Stop button on rear brake Light switch Turn indicator switch Horn button Horn Front turn indicator bulbs Front left turn indicator Heater control device Magneto flywheel Electronic ignition device Starter motor
Desc./Quantity
ELE SYS - 43
Electrical system
Fly
12 13 14 15 16
Specification Fuse box Battery rear left turn indicator Rear turn indicator bulbs Stop and tail light bulb
Desc./Quantity 12V - 4Ah Two, 12V-10W, spherical Type: Spherical Power: 12V 21/5W Quantity: 1
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
Rear light assembly rear right turn indicator Voltage regulator Mixer oil warning light control Start-up remote control switch Ground lead (-) starter motor wire unit Automatic starter Carburettor heater Chassis wire unit Fuel level transmitter front right turn indicator Key switch Starter button Front brake stop button Headlight Headlight bulb Front tail light bulb
35 36 37 38
Left turn indicator warning light Headlight warning light High-beam warning light Instrument panel light bulbs
12V-35/35W Type: All glass Power: 12V 5W Quantity: 1 12V - 2W 12V 1.2W 12V - 1.2W Type: All glass Power: 12V 1.2W Quantity: 3 12V - 2W 12V - 1.2W
39 40 41 42
Low fuel warning light Right turn indicator warning light Low oil warning light Odometer with warning lights and level indicator
Ar = Orange, Az = Sky Blue, Bi = White, Bl = Blue, Gi = Yellow, Gr = Grey, Ma = Brown, Ne = Black, Ro = Pink, Rs = Red, Ve = Green, Vi = Purple
Conceptual diagrams
ELE SYS - 44
Fly
Electrical system
Ignition
IGNITION
1 2 3 4 5 Specification Electronic control unit Magneto flywheel Pick - up Key switch Spark plug Desc./Quantity
ELE SYS - 45
Electrical system
Fly
LIGHTS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Specification Voltage regulator Magneto flywheel Light switch Rear light bulb Headlight bulb High-beam warning light N3 instrument lighting bulbs Taillight bulb Headlight warning light Heater control device Key switch contacts Fuse 7,5A Carburettor heater Automatic starter Battery Desc./Quantity
12V - 4Ah
ELE SYS - 46
Fly
Electrical system
12V - 4Ah
ELE SYS - 47
Electrical system
Fly
ELE SYS - 48
Fly
Electrical system
12V - 2W 12V-10W
Electrical system
Fly
- Rated voltage 12V. - Rated power 0.25 kW. - Left-hand rotation view from pinion side. - Connected to the engine by pinion and crown wheel on crankshaft, transmission side. - Push-button control. - Battery used for the test:12V-3,6Ah.
N.B.
THESE VALUES MUST BE MEASURED WITH A CHARGED BATTERY AND AFTER THE STARTER HAS BEEN ROTATING FOR 30" UNDER CONDITIONS OF POINT 1 In case the cause of ignition failure or malfunction cannot be easily identified at sight, first of all replace the control unit by another one in operating conditions. Remember that the engine must be off to disconnect and replace the control unit. If after replacement the vehicle starts properly, the control unit is failing and must be replaced. If the failure persists, check the generator and the stator components as follows: After visually checking the electrical connections, use a specific tester to measurement the stator winding and the pickup (see table). If any failure is found after checking the loading coil and the pick-up, replace the stator and the damaged parts. Disconnect the connector on the flywheel cover and measure the resistance between either contact and the earthing.
Specific tooling
020331Y Digital multimeter
PICK-UP CHECK
1 Specification 1) Brown cable and earth Desc./Quantity ~ 170
ELE SYS - 50
Fly
Electrical system
Ignition circuit
1) Check the state of the spark plug (clean it with a metallic brush, remove all incrustations, blow it with compressed air, and replace it if necessary). 2) Without removing the stator, perform the checks described below: After a visual inspection of the electrical connections, carry out the measurements on the charging coil and pick-up (see table), and check for continuity using the special tester, 020331Y. If the continuity checks or the inspections on the coil and pick-up are incorrect, proceed by replacing the stator, otherwise replace the ECU. Remember to detach the ECU wirings when the engine is not running.
Specific tooling
020331Y Digital multimeter
CONTINUITY CHECK
1 2 Specification White cable - Engine White cable - Frame Desc./Quantity Continuity Continuity
ELE SYS - 51
Electrical system
Fly
Stator check
- Using a tester, check the resistance between the stator wiring.
N.B. VALUES ARE STATED AT AMBIENT TEMPERATURE. A CHECK WITH THE STATOR AT OPERATING TEMPERATURE LEADS TO VALUES HIGHER THAN THOSE STATED.
Electric characteristic
Stator : Grey Ground ~ 1 ohm Stator : White Ground ~ 1 ohm Stator : Green - Ground ~ 1Kohm Stator : Blue Yellow ~ 1 ohm Pick-Up: Red - ground ~ 170 (Pick-Up)
ELE SYS - 52
Fly
Electrical system
FAULT 2: a) Make sure the stator is supplying voltage correctly: disconnect the regulator connector and place tester 020331 y between the grey-blue wire (2) and the black wire (6) to measure the alternating voltage and make sure that the voltage supplied at 3000 rpm, is between 25 and 30V (FIG> A). If there are any anomalies, replace the stator. b) If the tests do not reveal any anomalies, replace the regulator. c) If replacement of the regulator does not restore correct operation, check the connections of the electrical system. FAULT 3 After checking that there are no short circuits in the system towards earthing with the engine off and the regulator connector detached, replace the regulator because it is certainly inefficient, and replace the protection fuse. Following the replacement, measure the current and the recharging voltage on the battery ends (FIG. B). The values detected must be 1.5 2 A and 13 V at 3000 rpm. FAULT 4 a) By positioning tester 020331Y between the yellow wire terminal (8) on the regulator and the black wire (6) (FIG. D), check the generator output voltage is within 26 and 30 V at 3,000 rpm (this measurement must be carried out with the battery detached). In the event of anomalies, replace the stator; otherwise proceed to point b). b) Yellow wire (1) attached to the regulator. Insert an ammeter between the stator's blue wire (2) and the battery, and check, using tester 020331Y, that the current output, at 3,000 rpm and with the battery kept between 12 and 13V, is approx. 1.5 - 2 A (FIG. C).
ELE SYS - 53
Electrical system
Fly
If the values thus obtained are lower than prescribed, proceed by replacing the regulator. Before carrying out inspections on the regulator and its electrical system, it is always advisable to check for continuity between the black wire and earth.
FAULT 5 (FIG. E) If the turn indicators do not work, proceed as follows: - Remove the regulator connector, and insert the tester probes between the contact 5 (yellow-red) and the ground lead. - Turn the key switch to ON and check that the battery is getting voltage. If no voltage is detected, check the wiring and the contacts on the key switch and on the battery. (FIG. F) Repeat the procedure now placing the tester probes between contacts 5 (yellow/ red) and 6 (black), and check the presence of the battery voltage with the key switch set to ON. If there is no voltage, check the regulator ground wiring.
(FIG. G) If the above tests have positive results, jump the contacts 5 (yellow/red) and 7 (blue/black) on the connector, set the key switch to ON and shift the turn indicator switch to the right and left to see when the lights are steadily on (as they are powered directly from the battery). If even after this operation the turn indicators fail to turn on, check that the wiring is not damaged and the switch works properly. If these last two tests have a positive result, replace the regulator because it is certainly not functioning properly.
ELE SYS - 54
Fly
Electrical system
FAULT 6 Oil reserve check warning light not working (FIG H) - Disconnect the voltage regulator connector. - Supply 12V to the terminal marked with number 5; with a digital tester check that the terminal number 4 has a similar output (12V) for about 5 seconds. - If no voltage is detected for terminal number 4, replace the regulator. - If there is voltage for terminal number 4, check both the installation and the bulb of the oil warning light.
Specific tooling
020331Y Digital multimeter
Sealed battery
INSTRUCTIONS FOR REFRESHING THE STOCK CHARGE OF AN OPEN CIRCUIT 1) Voltage check Before installing the battery on the vehicle, check the open circuit voltage with a normal tester. - If the voltage exceeds 12.60 V, the battery may be installed without any renewal recharge. - If voltage is below 12.60 V, a renewal recharge is required as explained in 2). 2) Constant voltage battery charge mode -Constant voltage equal to 14.4014.70V -Initial charge voltage equal to 0.30.5 for nominal capacity -Duration of the charge: 10 to 12 h recommended Minimum 6 h Maximum 24 h 3) Constant current battery charge mode -Charge current equal to 1/10 of the nominal capacity of the battery -Duration of the charge: 5 h ELE SYS - 55
Electrical system
Fly
WARNING -WHEN THE BATTERY IS REALLY FLAT (WELL BELOW 12.6V) IT MIGHT BE THAT 5 HOURS OF RECHARGING ARE NOT ENOUGH TO ACHIEVE OPTIMAL PERFORMANCE. IN THESE CONDITIONS IT IS HOWEVER ESSENTIAL NOT TO EXCEED EIGHT HOURS OF CONTINUOUS RECHARGING SO AS NOT TO DAMAGE THE BATTERY ITSELF.
1 Hold the vertical tube 2 Look at the level 3 The float must be freed
Dry-charge battery
The battery is an electrical device which requires careful monitoring and diligent maintenance. The maintenance rules are: 1) Check the level of the electrolyte The electrolyte level must be checked frequently and must reach the upper level. Only use distilled water, to restore this level. If it is necessary to add water too frequently, check the vehicle's electrical system: the battery works overcharged and is subject to quick wear. 2)Load status check After restoring the electrolyte level, check its density using an appropriate densitometer (see the figure). When the battery is charged, you should detect a density of 30 to 32 B corresponding to a specific weight of 1.26 to 1.28 at a temperature of no lower than 15 C. A density reading of less than 20 B indicates that the battery is completely flat and it must therefore be recharged. After charging the battery, check each element electrolyte level and density. If the scooter is not used for a given time (1 month or more) it will be necessary to periodically recharge the battery. The battery runs down completely in the course of three months. If it is necessary to refit the battery in the vehicle, be careful not to reverse the connections, remembering that the earth wire (black) marked (-) must be connected to the - negative terminal while the other two red wires marked (+) must be connected to the terminal marked with the + positive sign. Regular bench charging must be carried out with the specific battery charger, (single) or (multiple), setting the battery charger selector to the type of battery to be recharged. Connections to the power supply source must be implemented by connecting the corresponding poles (+ to+ and - to -). 4) Cleaning the battery The battery should always be kept clean, especially on its top side, and the terminals should be coated with Vaseline.
WARNING
- Before recharging the battery, remove the plugs of each cell. Keep the battery away from naked flames or sparks when charging. Remove the battery from the vehicle removing the negative clamp first.
CAUTION
ELE SYS - 56
Fly
Electrical system
NEVER USE FUSES WITH A CAPACITY HIGHER THAN THAT RECOMMENDED. USING A FUSE OF UNSUITABLE RATING MAY SERIOUSLY DAMAGE THE VEHICLE OR EVEN CAUSE A FIRE.
CAUTION
DRINKING WATER CONTAINS MINERALS THAT CAN BE EXTREMELY HARMFUL TO THE BATTERY: USE DISTILLED WATER ONLY.
CAUTION
TO ENSURE MAXIMUM PERFORMANCE THE BATTERY MUST BE CHARGED BEFORE USE. INADEQUATE CHARGING OF THE BATTERY WITH A LOW ELECTROLYTE LEVEL BEFORE IT IS FIRST USED SHORTENS THE LIFE OF THE BATTERY.
Specific tooling
020333Y Single battery charger 020334Y Multiple battery charger
WARNING
- Battery electrolyte is toxic and it may cause serious burns. It contains sulphuric acid. Avoid contact with eyes, skin and clothing. In case of contact with eyes or skin, flush abundantly with water for about 15 minutes and seek immediate medical attention. In the event of accidental ingestion of the fluid, immediately drink large quantities of water or milk. Follow with milk of magnesia, beaten egg or vegetable oil. Seek immediate medical attention Batteries produce explosive gases; keep clear of free flames, sparks or cigarettes; ventilate the area when recharging the battery indoors. Always protect your eyes when working close to batteries. Keep out of the reach of children. 1)- Remove the short closed tube and the caps, then pour sulphuric acid into the cells using the type specified for batteries, with a specific gravity of 1.26, corresponding to 30 B, at a minimum temperature of 15C until the upper level is reached. 2) - Leave to rest for at least 2 hours; then, restore the level with sulphuric acid. 3)- Within the following 24 hours, recharge with the specific battery charger (single) or (multiple) at a density of about 1/10 of the battery nominal capacity and until the acid density is about 1.27, corresponding to 31 B, and these values are stabilised. 4) - Once the charge is over, level the acid (by adding distilled water). Close and clean carefully. 5)- Once the above operations have been performed, install the battery in the vehicle ensuring the connections between the wiring and the battery terminals are correct.
WARNING
- ONCE THE BATTERY HAS BEEN INSTALLED IN THE VEHICLE IT IS NECESSARY TO REPLACE THE SHORT TUBE (WITH CLOSED END) NEAR THE + POSITIVE TERMINAL WITH THE CORRESPONDING LONG TUBE (WITH OPEN END), THAT YOU FIND FITTED TO THE VEHICLE, TO ENSURE THAT THE GASES THAT FORM CAN ESCAPE PROPERLY.
Specific tooling
020333Y Single battery charger 020334Y Multiple battery charger
ELE SYS - 57
INDEX OF TOPICS
ENG VE
Fly
When installing the battery, first attach the positive cable and then the negative cable.
WARNING
ENG VE - 59
INDEX OF TOPICS
ENGINE
ENG
Fly
Engine
Kickstart
- Remove the seeger ring located on the exterior of the crankshaft. - Dismantle the dog gear from its seat, slackening the tension that the toothed sector applies to it by means of the spring; to do this, it is necessary to rotate the toothed sector slightly (see the figure).
CAUTION WHILE REMOVING THE TOOTHED SECTOR, BE VERY CAREFUL OF THE SPRING TENSION: IT COULD CONSTITUTE A HAZARD FOR THE OPERATOR.
- Upon refitting, apply the recommended grease to the bushing, to the spring and along the toothed sector. - Use the special tool for the charging of the spring, as shown in the figure. - Refit the seeger ring after checking that it is in good condition.
Specific tooling
020261Y Starter spring fitting
Recommended products
AGIP GREASE MU3 Grease for odometer transmission gear case
ENG - 61
Engine
Fly
- Remove the screws shown in the figure and remove the engine starting lever. - For the assembly, work in reverse and tighten the screws to the prescribed torque..
WHEN REMOVING/REFITTING THE BEARING, TAKE CARE NOT TO DAMAGE THE PAINTED SURFACE.
ENG - 62
Fly
Engine
Specific tooling
020565Y Flywheel lock calliper spanner
Characteristic
Clutch bell diameter/standard value 107+0.2 +0 mm Clutch bell diameter/max. value allowed after use 107.5 mm Eccentricity measured /max. 0.20 mm
ENG - 63
Engine
Fly
- Using a 34 mm socket wrench remove the clutch locking nut. - Loosen the central screw thereby undoing the driven pulley unit - Separate the components.
Specific tooling
020444Y Tool for fitting/ removing the driven pulley clutch
Characteristic
Check minimum thickness 1 mm
ENG - 64
Fly
Engine
- Remove the three guide pins and the mobile half pulley.
Specific tooling
001467Y029 Bell for bearings, O.D. 38 mm - Remove the ball bearing retention snap ring. - Expel the ball bearing from the side of the clutch housing by means of the special tool.
N.B. PROPERLY SUPPORT THE HALF-PULLEY SO AS NOT TO DEFORM THE SLIDING SURFACE OF THE DRIVING BELT
Specific tooling
020376Y Adaptor handle 020363Y 20-mm guide
Characteristic
ENG - 65
Engine
Fly
Stationary driven half-pulley/Standard diameter 33.965 to 33.985 mm Stationary driven half-pulley / Minimum diameter admitted after use 33.96 mm
Characteristic
Mobile driven half-pulley/ Maximum diameter allowed 34.08 mm - Check the belt contact surfaces. - Insert the new oil seal and O-rings on the mobile half-pulley. - Fitting the half-pulley on the bushing.
Recommended products
AGIP GREASE SM 2 Grease for the C-ring of the tone wheel Soap-based lithium grease containing NLGI 2 Molybdenum disulphide; ISO-L-XBCHB2, DIN KF2K-20 - Make sure the pins and collar are not worn, reassemble the pins and collar. - Use a greaser with a curved spout to lubricate the driven pulley unit with around 6 g of grease. This operation must be done through one of the holes inside the bushing until grease comes out of the opposite hole. This procedure is necessary to prevent the presence of grease beyond the O-ring.
Recommended products
AGIP GREASE SM 2 Grease for the C-ring of the tone wheel Soap-based lithium grease containing NLGI 2 Molybdenum disulphide; ISO-L-XBCHB2, DIN KF2K-20
ENG - 66
Fly
Engine
Specific tooling
020376Y Adaptor handle 020456Y 24 mm adaptor 020362Y 12 mm guide 020171Y Punch for 17 mm roller case
Characteristic
Standard length 118 mm Minimum length allowed after use XXXX
ENG - 67
Engine
Fly
- Reassemble the nut securing the clutch and tighten to the prescribed torque.
CAUTION SO AS NOT TO DAMAGE THE CLUTCH NUT USE A SOCKET WRENCH WITH SMALL CHAMFER. CAUTION POSITION THE NON-CHAMFERED SURFACES OF THE NUT IN CONTACT WITH THE CLUTCH
Specific tooling
020565Y Flywheel lock calliper spanner
Drive-belt
- Make sure the driving belt is not damaged and does not have cracks in the toothed grooves. - Check the width of the belt.
Characteristic
Transmission belt/Minimum width 17.5 mm
ENG - 68
Fly
Engine
- Remove the belt, washer and remove the mobile half-pulley with its bushing, being careful that the rollers and contrast plate fitted loosely on it do not come off.
Specific tooling
020451Y Starting ring gear lock
Engine
Fly
4) Check the integrity of the sliding blocks of the contact plate. - Check that the internal bushing shown in the figure is not abnormally worn and measure inside diameter A. - Measure outside diameter B of the pulley sliding bushing shown in the figure.
CAUTION DO NOT LUBRICATE OR CLEAN THE BUSHING.
Characteristic
Driving pulley / Maximum diameter: 20.12 mm Driving pulley/ Standard diameter: 20.021 mm Driving pulley bushing/ Diameter maximum: XXX mm Driving pulley bushing/ Standard diameter: 20 -0.020/-0.041mm
- Refit the components of the assembly (roller container assembly with bushing, limiting washer, stationary half-pulley, cooling fan belt with drive, washer and nut). - With the specific tool, tighten the lock nut to 20 Nm and then perform a final 90 locking in order to prevent the rotation of the driving pulley.
N.B. REPLACE THE NUT WITH A NEW ONE AT EVERY REFIT CAUTION UPON FITTING THE DRIVING PULLEY UNIT IT IS OF UTMOST IMPORTANCE THAT THE BELT IS FREE INSIDE IN
ENG - 70
Fly
Engine
ORDER TO AVOID WRONG TIGHTENING AND CONSEQUENTLY DAMAGING THE CRANKSHAFT KNURLING.
Specific tooling
020451Y Starting ring gear lock
Specific tooling
020363Y 20-mm guide 020376Y Adaptor handle ENG - 71
Engine
Fly
020477Y 37 mm adaptor
ENG - 72
Fly
Engine
- Remove the bearing off the driven pulley shaft using the specific tool and a press
N.B. USE THE SPECIFIC TOOL ON THE SIDE WITH THE SMALLER INTERNAL DIAMETER
Specific tooling
020452Y Tube for removing and refitting the driven pulley shaft
ENG - 73
Engine
Fly
Specific tooling
020452Y Tube for removing and refitting the driven pulley shaft
- Slightly heat the hub cover and then fit the bearing with the specific drift. - Fit the circlip with the concave or radial part facing the bearing.
N.B. FIT THE BALL BEARING WITH THE SHIELD FACING THE OIL SEAL.
Specific tooling
020151Y Air heater 020376Y Adaptor handle 020439Y 17-mm guide 020358Y 37x40-mm Adaptor
Specific tooling
020150Y Air heater mounting 020151Y Air heater 020376Y Adaptor handle
ENG - 74
Fly
Engine
Recommended products
Loctite 510 Liquid sealant
ENG - 75
Engine
Fly
Gasket
- Remove the oil piping retention band from the hood - Remove the 2 screws shown in the figure
Cooling fan
- Remove the cooling fan by acting on the three fixings indicated in the figure.
ENG - 76
Fly
Engine
THE PICK-UP CABLE MUST BE POSITIONED ADHERING TO THE FUSION TONGUE ON THE CRANKSHAFT IN SUCH A WAY AS TO AVOID BEING CRUSHED BY THE FAN COVER ASSEMBLY.
ENG - 77
Engine
Fly
Specific tooling
020565Y Flywheel lock calliper spanner 020162Y Flywheel extractor
ENG - 78
Fly
Engine
N.B. A VARIATION OF THE AIR GAP DISTANCE CAN LEAD TO A VARIATION IN THE IGNITION ADVANCE SUCH AS TO CAUSE PINGING, KNOCKING ETC.
ENG - 79
Engine
Fly
Characteristic
Rod small end: standard diameter 17 +0.011-0.001 Rod small end: maximum allowable diameter 17,060 mm
ENG - 80
Fly
Engine
Characteristic
Wrist pin: standard diameter 12 +0.005 +0.001 mm
Characteristic
Wrist pin housing: standard diameter 12 +0.007 +0.012 Wrist pin housing: standard clearance 0.002 0.011 mm - Measure the outer diameter of the piston, perpendicular to the pin axis. - Take the measurement in the position shown in the figure To classify the cylinder-piston fitting, check the appropriate table
See also
Cylinder - piston assy.
ENG - 81
Engine
Fly
See also
Cylinder - piston assy.
REFIT THE REMAINING PARTS FOLLOWING THE OPERATIONS IN REVERSE ORDER FROM THE REMOVAL OPERATIONS
Specific tooling
020166Y Pin lock fitting tool
ENG - 82
Fly
Engine
- Use new wrist pin snap rings. - Use new cylinder base gasket. - Before refitting carefully clean all the surfaces. - Use oil to be mixed during the fitting of the piston and the cylinder.
CAUTION POSITION THE ARROW PRINTED ON THE PISTON CROWN TOWARDS THE EXHAUST OPENING. THE WRIST PIN SNAP RINGS MUST BE POSITIONED ON THE PISTON WITH THE SPECIFIC TOOL
Recommended products
AGIP CITY TEC 2T Oil Recommended oil
ENG - 83
Engine
Fly
Install the special strip on the half crankcase on the flywheel side and separate the half crankcase on the flywheel side from the transmission side
Specific tooling
020163Y Crankcase splitting plate
ENG - 84
Fly
Engine
Specific tooling
020163Y Crankcase splitting plate
Specific tooling
004499Y001 Bearing extractor bell 004499Y006 Bearing extractor ring 004499Y002 Bearing extractor screw 004499Y007 Half rings - Using the specific tool remove any bearings left on the half crankcase
Specific tooling
001467Y007 Driver for OD 54 mm bearing 001467Y006 Pliers to extract 20 mm bearings
ENG - 85
Engine
Fly
Specific tooling
020265Y Bearing fitting base
Specific tooling
020335Y Magnetic mounting for dial gauge 020074Y Mounting base for checking crankshaft alignment
ENG - 86
Fly
Engine
- Firmly insert the crankshaft until the bearing reaches the end-of-stroke stop
- Let the temperature of the half crankcase settle at the temperature of the crankshaft. - Again install the special crankcase separation plate NOT installing the crankshaft protection - During the assembly phase keep the central thrust screw loose. - Take the four clamping screws to the end of the stroke and loosen them again with the same angle (e.g. 90) - When the temperature has settled, preload the thrust screw of the tool manually until the ball bearing clearance is cancelled out.
Specific tooling
020163Y Crankcase splitting plate
Recommended products
Loctite 510 Liquid sealant Gasket
ENG - 87
Engine
Fly
- Keeping the half crankcase on the transmission side, insert the flywheel side half crankcase with a clean precise movement - Insert at least three clamping screws and tighten up rapidly - Insert the other 5 screws and tighten them to the specified torque.
Specific tooling
020335Y Magnetic mounting for dial gauge
Characteristic
Axial clearance with warm crankcase 0.10 0.12 mm Axial clearance with cold crankcase 0.06 to 0.08 mm Limit value with cold crankcase 0.02 0.03 mm
ENG - 88
Fly
Engine
Refitting
- Install a new flywheel-side oil seal only with the special tool's punch The flywheel-side oil seal is recognised by its smaller diameter
N.B. THE USE OF THE SPECIFIC TOOL IS NOT COMPATIBLE WITH THE FITTED WRENCH
Specific tooling
020340Y Flywheel and transmission oil seals fitting punch - Install a new transmission side oil seal using the special tool with adapter ring. The transmission-side oil seal is recognised by the larger diameter
Specific tooling
020340Y Flywheel and transmission oil seals fitting punch
ENG - 89
Engine
Fly
Remove the tube passage seal from the crankcase shown in the figure
Refitting
To refit, perform the steps in the reverse direction to disassembly Remember to drain after refitting using the screw shown in the figure
Fuel supply
- Completely empty the fuel tank. - Remove the petrol delivery pipe and the lowpressure pipe. - Loosen the clip and remove the cock. - Clean the tank and the filter of the cock with a specific solvent. - Refit the cock making sure that there is an ORing. - Turn the cock to the direction it had before it was removed and block the clip.
N.B. THE FILTER CAN BE UNSCREWED FROM THE COCK TO FACILITATE CLEANING.
ENG - 90
Fly
Engine
- Disconnect the fuel supply and the suction taking pipe from the carburettor. - Check that there are no fuel leaks between the two tubes. - Close the fuel outlet pipe. - By means of the MITYVAC pump apply 0.1 bar of suction to the tap. - Make sure that the suction is kept stable and that and that there are no fuel leaks. - Reconnect the suction pipe to the manifold. - Position the fuel pipe with the outlet at the point of the tap. - Turn the engine by using the starter for five seconds with the carburettor at minimum. - Take up the fuel by means of a graded burette.
N.B. THE MEASUREMENT MAY BE FALSIFIED BY THE INCORRECT NUMBER OF REVS OR BY THE WRONG POSITION OF THE TUBE. IN THIS CASE, THE TENDENCY IS TO OBTAIN A REDUCED FUEL FLOW RATE. THE SUCTION OUTLET ON THE MANIFOLD HAS A SECTION INTENTIONALLY REDUCED FOR THE PURPOSE OF ENHANCING THE SUCTION PULSATION AND THEREBY GUARANTEE A CONSTANT TAP FLOW RATE.
Specific tooling
020329Y Mity-Vac vacuum-operated pump
Characteristic
Minimum flow rate 20 cc
ENG - 91
INDEX OF TOPICS
SUSPENSIONS
SUSP
Fly
Suspensions
This section is devoted to operations that can be carried out on the suspensions.
- Remove the internal spacer - Use appropriate handle, adaptor and guide and hit with a mallet to extract the bearing and the spacer bushing on the brake disc side; insert handle on the side the rpm indicator detects movement, as shown in the photo
SUSP - 93
Suspensions
Fly
- Check that the bearings do not show flaws or jamming. Otherwise, replace them. - Check that the internal spacer does not show abnormal wear. Otherwise, replace it. - With a hot air gun heat the seat of the bearing on the brake calliper side - With an appropriate tool remove the bearing on the brake disc side - Insert the spacer bushing on the brake disc side
- With a hot air gun heat the seat of the bearing on the side the rpm indicator detects movement - Insert the internal spacer with the centring ring facing to the brake disc side, as shown in the photo - Use an appropriate tool to insert the bearing on the side the rpm indicator detects movement
Specific tooling
001467Y009 Driver for OD 42-mm bearings 001467Y014 Pliers to extract 15-mm bearings 020357Y 32x35-mm Adaptor 020376Y Adaptor handle 020412Y 15-mm guide 020456Y 24 mm adaptor
SUSP - 94
Fly
Suspensions
Handlebar Removal
Handlebars removal Remove the handlebar cover before carrying out this operation,. - After removing the transmissions and disconnecting the electrical terminals, remove the terminal fixing the handlebar to the steering. - Check all components and replace faulty parts.
N.B. IF THE HANDLEBAR IS BEING REMOVED TO REMOVE THE STEERING, TILT THE HANDLEBAR FORWARD TO AVOIDING DAMAGING THE TRANSMISSIONS.
Refitting
Carry out the removal operations but in the reverse order, observing the prescribed tightening torque.
Suspensions
Fly
- Remove the upper screw (2). - Add 30 cc 1 "Fork PG" oil (SAE 20W oil for forks). - Refit all components.
Steering bearing
Steering locking ring nut Steering lock ring nut
Top washer and upper bearing housing - Lubricate race and balls with Z2 grease. - Tighten to the specified torque and then rotate the tool through 80 - 90 in an anticlockwise direction.
Removal
Lower and upper races from frame
SUSP - 96
Fly
Suspensions
To remove the bearing seats from the chassis, use the appropriate tool as shown in the figure.
N.B. To remove the lower seating of the lower bearing just use a screwdriver as a lever between the seating and the shell.
Top washer and upper bearing housing After removing the upper seating, tilt the vehicle to a side and take out the steering tube making sure mudflaps have been removed and the calliper disconnected.
SUSP - 97
Suspensions
Fly
Centre-stand
Centre-stand bolt refitting and caulking to mounting bracket - Caulk the end of the pin P between the two punches shown in the figure. - After caulking it must be possible for the stand to turn freely.
N.B. UPON REFITTING USE NEW O-RING AND PIN, GREASE THE SPRING ATTACHMENTS AND THE PIN.
Fly
Suspensions
- Work on the screws shown in the figure. - When refitting, secure to the prescribed torque.
SUSP - 99
INDEX OF TOPICS
BRAKING SYSTEM
BRAK SYS
Fly
Braking system
Once the muffler and the wheel have been removed, follow these steps: 1.Remove the shoe spring using the specific spanner. 2. Remove the shoe with the aid of a lever. 3. Refit the new shoes giving a few taps with the mallet. 4. Attach the spring using the specific pliers.
Specific tooling
020325Y Pliers for brake-shoe springs
ALL THE INTERNAL COMPONENTS MUST BE REPLACED EVERY TIME THE CALLIPER IS SERVICED.
Specific tooling
020335Y Magnetic mounting for dial gauge
Braking system
Fly
Fill Front
-Once the bleed valve is closed, fill the system with brake liquid to the maximum level. -Undo the bleed screw. -Apply the tube of the special tool to the bleed screws. When bleeding it is necessary to fill the oil tank in continuation while working with a MITYVAC pump on the bleed screws until no more air comes out of the system. The operation is finished when just oil comes out of the bleed screws. -Do up the bleed screw. -When the operation is over, tighten up the oil bleed screw to the prescribed torque.
N.B. IF AIR CONTINUES TO COME OUT DURING PURGING, EXAMINE ALL THE FITTINGS: IF SAID FITTINGS DO NOT SHOW SIGNS OF BEING FAULTY, LOOK FOR THE AIR INPUT AMONG THE VARIOUS SEALS ON THE PUMP AND CALLIPER PISTONS. CAUTION - DURING THE OPERATIONS, THE VEHICLE MUST BE ON THE STAND AND LEVEL. N.B.
Fly
Braking system
DURING PURGING FREQUENTLY CHECK THE LEVEL TO PREVENT AIR GETTING INTO THE SYSTEM THROUGH THE PUMP. WARNING - BRAKING CIRCUIT FLUID IS HYGROSCOPIC. IT ABSORBS HUMIDITY FROM THE SURROUNDING AIR. IF THE LEVEL OF HUMIDITY IN THE BRAKING FLUID EXCEEDS A GIVEN VALUE, BRAKING EFFICIENCY WILL BE REDUCED. THEREFORE, ALWAYS USE FLUID FROM SEALED CONTAINERS. UNDER NORMAL DRIVING AND CLIMATIC CONDITIONS YOU SHOULD CHANGE THIS LIQUID EVERY TWO YEARS. IF THE BRAKES ARE USED INTENSELY AND/OR IN HARSH CONDITIONS, CHANGE THE FLUID MORE FREQUENTLY. CAUTION WHEN CARRYING OUT THE OPERATION, BRAKE FLUID MAY LEAK FROM BETWEEN THE BLEED SCREW AND ITS SEAT ON THE CALLIPER. CAREFULLY DRY THE CALLIPER AND DEGREASE THE DISC SHOULD THERE BE OIL ON IT.
Specific tooling
020329Y Mity-Vac vacuum-operated pump
Recommended products
AGIP BRAKE 4 Brake fluid FMVSS DOT 4 Synthetic fluid
Braking system
Fly
Removal
- Bleed the circuit and drain the brake fluid through the bleeding screw located on the calliper and actuate the brake lever until no more fluid flows out. -Remove the oil pump from the handlebar; remove the brake lever and then remove the wheel cylinder. 1 - Tank cap screw. 2. Tank cover. 3. Diaphragm. 4. Bellows. 5. Sealing ring. 6. Piston. 7. Gasket. 8 - Spring
CAUTION - THE PRESENCE OF BRAKE FLUID ON THE DISC OR BRAKE PADS REDUCES THE BRAKING EFFICIENCY. IN THIS CASE, REPLACE THE PADS AND CLEAN THE DISC WITH A HIGH-QUALITY SOLVENT. CONTACT WITH BRAKE FLUID WILL DAMAGE PAINTED SURFACES. RUBBER PARTS SHOULD NEVER BE LEFT IN ALCOHOL FOR LONGER THAN 20 SECONDS. AFTER WASHING, THE PIECES MUST BE DRIED WITH A BLAST OF COMPRESSED AIR AND A CLEAN CLOTH. THE SEALING RINGS MUST BE IMMERSED IN THE OPERATING LIQUID.
Refitting
Before fitting, the parts must be perfectly clean and free of traces of oil, diesel fuel, grease, etc.. They should be washed thoroughly in denatured alcohol before proceeding. - Reinstall the individual parts in the reverse order to the removal, paying attention to the correct positioning of the rubber parts in order to ensure leak tightness. 1 - Tank cap screw. 2. Tank cover. 3. Diaphragm. 4. Bellows.
Fly
Braking system
INDEX OF TOPICS
CHASSIS
CHAS
Fly
Chassis
Carrozzeria
Footrest
- Remove the side fairings - Remove the shield back plate - Remove the 6 screws shown in the photograph
CHAS - 107
Chassis
Fly
Rear mudguard
- Remove the side fairings - Remove the 4 screws shown in the photograph
Helmet bay
- Remove the side fairings - Remove the helmet compartment by undoing the 4 screws indicated in the figure
CHAS - 108
Fly
Chassis
Fuel tank
- Remove the side fairings - Remove the rear mudguard - Remove the crews shown in the photograph - Remove the shock absorber upper clamping in order to create the necessary space to take out the tank.
CHAS - 109
INDEX OF TOPICS
PRE-DELIVERY
PRE DE
Fly
Pre-delivery
Aesthetic inspection
Appearance check: - Paintwork - Fitting of plastics - Scratches - Dirt
Electrical system
Electrical system: - Main switch - Headlamps: high-beam lights, low-beam lights, tail and parking lights and their warning lights - Adjusting the headlights according to the regulations currently in force - Rear light, parking light, stop light - Front and rear stop light switches - Turn indicators and their warning lights - Instrument panel lights - Instrument panel: fuel gauge - Instrument panel warning lights - Horn - Starter PRE DE - 111
Pre-delivery
Fly
CAUTION
TO ENSURE MAXIMUM PERFORMANCE, THE BATTERY MUST BE CHARGED BEFORE USE. INADEQUATE CHARGING OF THE BATTERY WITH A LOW LEVEL OF ELECTROLYTE BEFORE IT IS FIRST USED SHORTENS THE LIFE OF THE BATTERY.
WARNING
BEFORE RECHARGING THE BATTERY, REMOVE THE CAPS OF EACH CELL. KEEP THE BATTERY AWAY FROM NAKED FLAMES OR SPARKS WHILE IT IS CHARGED. REMOVE THE BATTERY FROM THE SCOOTER, DISCONNECTING THE NEGATIVE TERMINAL FIRST.
CAUTION
WHEN INSTALLING THE BATTERY, ATTACH THE POSITIVE LEAD FIRST AND THEN THE NEGATIVE ONE.
WARNING
BATTERY ELECTROLYTE IS TOXIC AND IT MAY CAUSE SERIOUS BURNS. IT CONTAINS SULPHURIC ACID. AVOID CONTACT WITH YOUR EYES, SKIN AND CLOTHING. IN CASE OF CONTACT WITH YOUR EYES OR SKIN, RINSE WITH ABUNDANT WATER FOR ABOUT 15 MINUTES AND SEEK IMMEDIATE MEDICAL ATTENTION. IF IT ACCIDENTALLY SWALLOWED, IMMEDIATELY DRINK LARGE QUANTITIES OF WATER OR VEGETABLE OIL. SEEK IMMEDIATE MEDICAL ATTENTION. BATTERIES PRODUCE EXPLOSIVE GASES; KEEP THEM AWAY FROM NAKED FLAMES, SPARKS AND CIGARETTES. IF THE BATTERY IS CHARGED IN A CLOSED PLACE, TAKE CARE TO ENSURE ADEQUATE VENTILATION. ALWAYS PROTECT YOUR EYES WHEN WORKING CLOSE TO BATTERIES. KEEP OUT OF THE REACH OF CHILDREN
CAUTION
NEVER USE FUSES WITH A CAPACITY HIGHER THAN THAT RECOMMENDED. USING A FUSE OF UNSUITABLE RATING MAY SERIOUSLY DAMAGE THE VEHICLE OR EVEN CAUSE A FIRE.
Levels check
Level check: - Hydraulic braking system fluid level. - Rear hub oil level - Engine coolant level.
Road test
Test ride - Cold start - Instrument operations - Response to the throttle control - Stability on acceleration and braking - Rear and front brake efficiency - Rear and front suspension efficiency - Abnormal noise
Static test
Static control after the test ride: PRE DE - 112
Fly
Pre-delivery
- Starting when warm - Starter operation - Minimum hold (turning the handlebar) - Uniform turning of the steering - Possible leaks
CAUTION
Functional inspection
Functional check up: Braking system (hydraulic) - Lever travel Braking system (mechanical) - Lever travel Clutch - Proper functioning check Engine - Throttle travel check Others - Check documentation - Check the frame and engine numbers - Tool kit - License plate fitting - Check locks - Check tyre pressures - Installation of mirrors and any accessories
PRE DE - 113
INDEX OF TOPICS
TIME
TIME
Fly
Time
This section is devoted to the time necessary to carry out repairs. The description and code for each operation is indicated.
Engine
ENGINE
Code 001001
Duration
TIME - 115
Time
Fly
Crankcase
CRANKCASE
1 Code 001133 Action Engine crankcase - Replacement Duration
TIME - 116
Fly
Time
Crankshaft
CRANKSHAFT
1 2 3 4 Code 001118 001100 001099 001117 Action Main bearings - Replacement Clutch-side oil seal - Replacement Oil seal, flywheel side - Replacement Crankshaft - Replacement Duration
TIME - 117
Time
Fly
Cylinder assy.
CYLINDER- PISTON
1 2 Code 001002 001107 Action Cylinder-Piston - Replacement Cylinder / piston - Inspection / cleaning Duration
TIME - 118
Fly
Time
HEAD
1 2 3 4 5 Code 001097 001093 001126 001013 001178 Action Cooling hood - Replacement Spark plug - Replacement Head - Replacement Intake manifold - Replacement Disc pack - Replacement Duration
TIME - 119
Time
Fly
Driven pulley
TIME - 120
Fly
Time
Oil pump
OIL PUMP
1 2 3 Code 001028 001019 001018 Action Mix movement gear socket - Replacement Mixer belt - replacement Mixer - Replacement Duration
TIME - 121
Time
Fly
Driving pulley
DRIVING PULLEY
1 2 3 4 Code 001066 001086 001011 001177 Action Driving pulley - Removal and refitting Driving half-pulley - replace Driving belt - Replacement Variator rollers / shoes - Replacement Duration
TIME - 122
Fly
Time
Transmission cover
TRANSMISSION COVER
1 2 3 Code 001087 001135 001096 Action Flywheel cover - Replacement Transmission cover bearing - Replacement Transmission crankcase cover - Replacement Duration
TIME - 123
Time
Fly
Flywheel magneto
FLYWHEEL - FAN
1 2 3 4 Code 001109 001173 001067 001058 Action Cooling fan - Replacement Rotor - Replacement Stator - Fitting and Refitting Flywheel - Replacement Duration
TIME - 124
Fly
Time
Carburettor
CARBURATOR
1 2 3 4 Code 001008 001063 007020 001081 Action Carburettor - Inspection Carburettor - Replacement Carburettor heating tubing - replacement Automatic choke - Replacement Duration
TIME - 125
Time
Fly
Exhaust pipe
MUFFLER
1 2 3 Code 001009 001095 001136 Action Muffler - Replacement Muffler guard - Replacement Exhaust emissions - Adjustment Duration
TIME - 126
Fly
Time
Air cleaner
AIR CLEANER
1 2 3 Code 004122 001014 001015 Action Air cleaner carburettor fitting - Replacement Air filter - Replacement / cleaning Air filter box - Replacement Duration
TIME - 127
Time
Fly
Frame
STAND
1 2 3 Code 004001 004004 001053 Action Frame - replace Stand - Replacement Stand bolt - Replacement Duration
TIME - 128
Fly
Time
Legshield spoiler
TIME - 129
Time
Fly
Rear cover
REAR SHIELD
1 2 3 Code 004174 004065 004081 Action Trunk levers - Replacement Legshield, rear part - Removal and refitting Top box lid - Replacement Duration
TIME - 130
Fly
Time
Central cover
CENTRAL COVER
1 2 3 4 5 Code 004059 004106 004085 004105 004131 Action Spark plug inspection flap - Replacement Under-saddle band - Replacement Fairing (1) - Replacement Right side clamp - Replacement Luggage rack support - Replacement Duration
TIME - 131
Time
Fly
Mudguard
MUDGUARDS
1 2 Code 004002 004009 Action Front mudguard - Replacement Rear mudguard - Replacement Duration
TIME - 132
Fly
Time
Fuel tank
FUEL TANK
1 2 3 4 5 6 Code 004168 005010 004112 004005 004007 004109 Action Fuel tank cap - Replacement Tank float - Replacement Cock-carburettor hose - Replacement Fuel tank - Replacement Fuel valve - Replacement Fuel tank breather - change Duration
TIME - 133
Time
Fly
Tank oil
OIL RESERVOIR
1 2 3 4 Code 005018 004017 004095 004091 Action Oil reservoir float - Replacement Oil reservoir - Replacement Oil reservoir cock - Replacement Oil reservoir hose - Replacement Duration
Rear shock-absorber
TIME - 134
Fly
Time
TIME - 135
Time
Fly
Handlebar covers
HANDLEBAR COVERS
1 2 3 4 5 6 Code 004019 004018 005078 005076 005014 005038 Action Handlebar rear section - Replacement Handlebar front section - Replacement Odometer glass - Replacement Clock / Cell - Replacement Odometer - Replacement Instrument panel warning light bulbs - Replacement Duration
TIME - 136
Fly
Time
Handlebar components
HANDLEBAR COMPONENTS
1 2 3 4 5 6 7 8 9 10 Code 004066 002037 002071 003001 005017 002024 002054 002060 004162 002059 Action Driving mirror - Replacement Brake or clutch lever - Replacement Left hand grip - Replacement Handlebar - Replacement Stop switch - Replacement Front brake pump - Removal and Refitting Throttle or splitter transmission complete - Replacement Complete throttle control - Replacement Mirror support and/or brake pump fitting U-bolt - Replacement Right hand grip - Replacement Duration
TIME - 137
Time
Fly
Swing-arm
SWINGING ARM
1 Code 001072 Action Engine-frame connection swinging arm - Replacement Duration
TIME - 138
Fly
Time
Seat
SADDLE
1 2 Code 004003 004068 Action Saddle - Replacement Passenger handgrip - Replacement Duration
TIME - 139
Time
Fly
TIME - 140
Fly
Time
Front wheel
FRONT WHEEL
1 2 3 4 5 6 7 Code 003038 002011 003040 003047 003037 004123 002041 Action Front wheel axle - Remov. and refitt. Odometer movement sensor - Replacement Front wheel bearings - Replacement Front tyre - Replacement Front wheel rim - Removal and Refitting Front wheel - Replacement Front brake disc - Replacement Duration
Grease tone wheel or drive Please take note that the code has been introduced: 900001 - Tone wheel / drive greasing - 15'. Never mistake the codes 002011 (movement sensor replacement) and 005089 (tone wheel replacement) in the event of noise of the indicated components. The grease recommended is TUTELA MRM 2 (soap-based lithium grease with Molybdenum disulphide). In the following points we indicate with an arrow the area to be greased (1 - Drive, 2 - Tone wheel)
TIME - 141
Time
Fly
Rear wheel
REAR WHEEL
1 2 3 4 Code 004126 001071 001016 002002 Action Rear wheel tyre - Replacement Rear wheel rim - Removal and Refitting Rear wheel - Replacement Rear brake pads/shoes - Repl. Duration
TIME - 142
Fly
Time
Electric start
ELECTRICAL START-UP
1 2 3 4 5 6 Code 001020 005045 001017 001021 008008 001084 Action Starter motor - Replacement Starter motor cable harness - Replacement Starter sprocket wheel - Replacement Kick starter - Inspection Starter spring pack - Replacement Starter lever - Replacement Duration
TIME - 143
Time
Fly
Electric devices
ELECTRICAL DEVICES
1 2 3 4 Code 005007 005011 005052 005054 Action Battery - change Start-up contactor - Replacement Fuse (1) - Replacement Fuse block (1) - Replacement Duration
TIME - 144
Fly
Time
ELECTRICAL DEVICES
1 2 3 4 5 Code 005001 005009 001094 001023 005114 Action Electrical system - Replacement Voltage regulator - Replacement Spark plug cap - Replacement Control unit - Replacement Electrical system - Service Duration
TIME - 145
Time
Fly
Electronic controls
ELECTRIC CONTROLS
1 2 3 4 5 6 7 Code 005039 005006 005040 005003 005041 005016 004096 Action Lights switch - Replacement Light or turning indicator switch - Replacement Horn button - Replacement Horn - Replacement Starter button - Replacement Key switch - Replacement Lock series - Replacement Duration
TIME - 146
Fly
Time
Transmissions
TRANSMISSION
1 2 3 4 5 6 7 Code 002051 002012 002057 002058 002053 002049 003061 Action Odometer transmission assembly Replacement Splitter - Replacement Carburettor / splitter transmission complete - Replacement Mix / splitter transmission complete Replacement Rear brake transmission complete Replacement Odometer cable - Replacement Accelerator transmission - adjust Duration
TIME - 147
Time
Fly
Brake callipers
CALLIPER
1 2 3 4 Code 002021 002007 002039 002047 Action Front brake hose - Remov. and Refitt. Front brake shoes/pads - Remov. and Refitt Front brake calliper - Removal and Refitting Front brake fluid and air bleed system - Replacement Duration
TIME - 148
Fly
Time
Steering column
STEERING
1 2 3 4 Code 003048 003076 003079 003010 Action Fork oil seal - Replacement Fork sheath - Replacement Fork stem - Replacement Front suspension - Service Duration
TIME - 149
Time
Fly
Helmet bay
HELMET COMPARTMENT
1 2 Code 004016 005046 Action Helmet compartment - Removal and Refitting Battery cover - change Duration
TIME - 150
Fly
Time
TIME - 151
Time
Fly
TIME - 152
A
Air filter: 30
B
Battery: 40, 47, 55, 56 Brake: 101103, 148
C
Carburettor: 11, 27, 125
E
Engine stop:
F
Fuel: 39, 90, 109, 133
H
Headlight: 33 Horn: Hub oil: 29
I
Identification: 8
M
Maintenance: 7, 25
S
Saddle: Shock absorbers: 98 Spark plug: 28 Stand: Start-up:
T
Tank: 109, 133, 134 Transmission: 10, 39, 61, 123 Turn indicators: Tyres: 10