Documente Academic
Documente Profesional
Documente Cultură
2
3
4
5
6
8
9
10
11
Shell Inputs:
SA-240 304 Material
20,000 Sv [psi] - allowable stress
1.00 E1 - efficiency of shell at nozzle
24.000
0.204
0.015
0.015
12
13
14
15
16
17
18
19
4.000
0.160
1.000
1.000
0.015
12.5%
50.0
21
22
23
24
25
26
35
Reinforcement:
SA-240 304
20,000
0.250
6.000
0.200
0.200
0.200
0.250
36
Variables:
28
29
30
31
32
33
34
37
38
39
40
41
42
43
44
45
46
47
Nozzle Inputs:
SA-312 304 Material
20,000 Sn [psi] - allowable stress
1.00 E - nozzle efficiency
20
27
Page 1 of 2
UT [in] =
Rn [in] =
ti [in] =
h [in] =
tn [in] =
d [in] =
Material
Sp [psi] - allowable stress of repad
te [in] - repad thickness
Dp [in] - outside diameter
Leg41 [in] - fillet size
Leg42 [in] - fillet size
Leg43 [in] - fillet size
LegG [in] - depth of groove
Nwall*UTP
Do/2 - (Nwall-nca) + UT
Nwall-2*nca
MIN(Ip-sca,2.5*nt,2.5*ti)
Nwall-nca
Do-2*tn
0.16*0.1 =
4/2 - (0.16-0.015) + 0.02 =
0.16-2*0.015 =
MIN(1-0.015,2.5*0.204,2.5*0.13) =
0.16-0.015 =
4-2*0.145 =
0.020
1.875
0.130
0.325
0.145
3.710
Acceptable 0.078
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
1*3.71*0.015*1+2*0.145*0.015*1*(1-1) =
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
MAX(3.71, 2*(0.204+0.145)) * (1*0.204-1*0.015)-2*0.145*(1*0.204-1*0.015)*(1-1) =
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
MIN((0.145-0.005)*1*MIN(5*0.204,2*1),(0.145-0.005)*(MIN(2.5*0.145+0.25,2*1)*1*2)) =
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
MIN(5*0.204*0.13*1,5*0.13*0.13*1,2*0.325*0.13*1) =
A5 [in^2] = (Dp-d-2*tn)*te*fr4
(6-3.71-2*0.145)*0.25*1 =
A41 [in^2] = Leg41^2*fr3
0.2^2*1 =
A42 [in^2] = Leg42^2*fr4
0.2^2*1 =
A43 [in^2] = (Leg43-nca)^2*fr2
(0.2-0.015)^2*1 =
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
0.701+0.143+0.085+0.5+0.04+0.04+0.034 =
CheckA = Aa >= Ar ~~ check area replacement
1.543 >= 0.056 =
The UG-16(b) minimum thickness requirement has not been taken into consideration here.
The required weld size is not checked on this sheet
This sheet cannot be used to check for allowable exterior pressure loads.
This sheet is for educational use only - use at your own risk.
0.056
0.701
0.143
0.085
0.500
0.040
0.040
0.034
1.543
Acceptable