Documente Academic
Documente Profesional
Documente Cultură
10/09/2013
ZTE CABINETS
ZTE CABINETS
10/09/2013
1161
69
43
31
27
BTS V 2.0
BS21(V2.0)
M8206
BS30(V1.2)
ZTE CABINETS
WORKING PRINCIPLE
10/09/2013
Data link
B S C
Abis
RF signal
Um interface
System clock
220V
Heat exchanger
ZTE CABINETS
WORKING PRINCIPLE
10/09/2013
Data link
B S C
Abis
RF signal
Um interface
System clock
Downlink: The BTS receives data from BSC, including voice and signaling data. Power Supply Module 220V The transmission unit sends signaling data to the operation & maintenance unit for processing. The voice data are then sent to baseband processor for processing of rate conversion, encryption and interleaving. Heat exchanger Data are then sent to RF unit for modulation to high-frequency signals. Finally, data are then transmitted through the antenna feeder processor.
ZTE CABINETS
WORKING PRINCIPLE
10/09/2013
Data link
B S C
Abis
RF signal
Um interface
System clock
Uplink: The antenna feeder processor receives the RF signals from the MS. It then Module sends these signals to Power Supply the RF unit to 220V convert into digital signals. The signals are then transmitted to baseband processor for rate signals conversion, decryption and de-interleaving. Heat exchanger After conversion to the code pattern, suitable for long-distance transmission, the signals are sent to the BSC through the Abis interface.
ZTE CABINETS
10/09/2013
ZTE CABINETS
MMI
TR/ETRM1
BSC
Abis
TR/ETRM2 TR/ETRM3
A E M
Um
ZTE CABINETS
MMI
BSC
Abis
The CMM TR/ETRM1 (Control & Maintenance Module) performs the following functions: Abis interface processing A BTS operation & maintenance TR/ETRM2 E Clock synchronization and generation M Collection of internal/external alarms Fan management and the TR/ETRM3 active/standby function
Um
ZTE CABINETS
MMI
BSC
The TRM/ETRM ( Transceiver Module ) performs the following functions: Runs and Controls radio channels in Abis GSM system CMM Sends/receives radio channel data Modulates/demodulates baseband signals on the radio carrier frequency PDM Sends/receives radio carrier signals and collects alarms of the fans and AEMs.
FCM BTM
ZTE CABINETS
MMI
TR/ETRM1
BSC
Abis
TR/ETRM2 TR/ETRM3
A E M
Um
The BTM (Backplane Transmission Module) contains Motherboard of CMM (MCMM), Motherboard of Transceiver Module (MTRM).
ZTE CABINETS
MMI
BSC
Abis
AEM (Antenna Equipment Module) provides the following functions: Combines the transmit signals of multiple CMM TR/ETRM2 carriers. Provides bidirectional signal channels from the BTS to the antenna for the transmitting PDM band and from the antenna TR/ETRM3 to the BTS for the receiving band. Gives an alarm when the VSWR of the antenna port deteriorates. FCM Suppresses the interference out of the working band and spurious emission. Flexibly configures carriers. BTM Implements diversity receiving.
TR/ETRM1
A E M
Um
ZTE CABINETS
MMI
TR/ETRM1
BSC
Abis
TR/ETRM2
A E M
Um
The PDM (Power Distribution Module) TR/ETRM3 performs the following functions: Distributes -48 V DC power to all the modules Provides overload protection Stabilizes the input power
ZTE CABINETS
MMI
TR/ETRM1
BSC
Abis
The FCM (Fan Control Module) monitors and CMM TR/ETRM2 collects the temperature in the carrier shelves and dissipates heat through fans.
A E M
Um
TR/ETRM3
ZTE CABINETS
10/09/2013
ZTE CABINETS
HW signal
Optical interface
RX
E1
TX
Internal FAN
PWM
HTM
AC 220V
ZTE CABINETS
HW signal
Optical interface
RX
E1
TX The transceiver for station module (TSM), consist of controller & maintenance module (CMM), transceiver module (TRM) and backboard Internal connection unit (BCU) PWM HTM FAN AC 220V
ZTE CABINETS
HW signal
Optical interface
RX
E1
TX The DPM (Duplexer Module ) provides bidirectional channels for signals between the BTS and the antenna, suppresses the interference and spurious radiation beyond the working band, and implements SWR PWM at the antenna HTM port. alarm detection
Internal FAN
AC 220V
ZTE CABINETS
HW signal
Optical interface
RX
E1 CMM (Controller & Maintenance Module ) provides such functions as Abis interface processing, BS operation & maintenance, clock synchronization and generation, and internal/external alarm collection and processing. CMM consists of a control O&M board.
TX
Internal FAN
PWM
HTM
AC 220V
ZTE CABINETS
HW signal
Optical interface
RX
E1
CMM Dup The ZXG10 BS30 supports built-in SDH transmission equipment, which is implemented by configuring STM. The STM is the T150 researched and manufactured by ZTE. T150 provides the ZXG10 BS30 with 155 Mbits/s SDH interface, providing diversified BS transmission interfaces.
Internal FAN
TX
PWM
HTM
AC 220V
ZTE CABINETS
HW signal
Optical interface
DPM LNA
E1
PWM (Power Supply Module ) provides Receiving rectification, filtering and voltage filter CMM stabilizing protection of 220 VAC (singleDup phase three-lines), supplies 220 VAC for HTM, TSM, STM and internal/external fans, and provides 220 VAC input over/undervoltage dry contact alarm.
RX
TX
Internal FAN
PWM
HTM
AC 220V
ZTE CABINETS
HW signal
Optical interface
RX
E1
TX HTM (Heater Module) consists of a heater and a fan. It serves to control internal temperature and ensure the normal operation of the equipment.
Internal FAN
PWM
HTM
AC 220V
ZTE CABINETS
10/09/2013
ZTE CABINETS
Delay ALM
SYS CLK / 13M CLK
LMT
3E1/T1
Abis ODU
48V
ZTE CABINETS
48V
MDUP
MDUP
MPAU
M P W R 48V
ZTE CABINETS
MTRB
MTRB (Micro Base Station Transceiver MDUP Board) consists of transmitter, receiver, local oscillator and base band processor. Main functions of MTRB are as follows: Transmission and reception of radio signal and uplink/downlink conversion. Processing the dual-carriers radio channels in downlink. Implement rate adaptation, channel encoding, interleaving, and encryption. Also generates TDMA burst pulse and implements M GMSK/8PSK modulation. R Receives the system clock fromP CMB. I Implements and saves hardware management W ID. B R type, and Board version. Implements RF hopping.
MDUP
MPAU
MTRB
48V
ZTE CABINETS
MDUP
MPAU (Micro Base Station Power Amplifier Unit) is power amplifying unit and amplifies the downlink signal power. MPAU consists of two power amplifier boards which are installed on the bottom of base station cabinet respectively.
MDUP
MPAU
M P W R 48V
ZTE CABINETS
R I B
MTRB
MDUP
MDUP
M P W R 48V
ZTE CABINETS
This unit works as a duplexer and consists of transceiver duplexer, antenna interface VSWR detection unit and Low Noise Amplifier (LNA). It detects VSWR alarms in three levels
RTU Interface Board
MPAU
MTRB
MDUP
MDUP
MPAU
MPWR performs power distribution function. It provides different values of voltage according to the requirements in different parts of the RTU.
M P W R 48V
MTRB
ZTE CABINETS
48V
Heater
MEIB
5E1/T1
48V
T150 IDU
ZTE CABINETS
Monitors, controls and maintains the whole BTS system. Provides 8 channels E1/T1 interfaces, but only 5 channels are used in this system. PWR Implements the synchronization of radio clock and transmission clock. Provides transparent path for external environment alarm. Implements shared PCM link for multi-BTS. 48V Supports cascaded capacity expansion of many Heater physical cabinets in one site. Provides various clocks required in BTS Administers the intra-system program of each board and version of FPGA configuration file. Supports near 48V end and far end version upgrade. Provides protection from reverse current. Its front panel provides reset button and forced power OFF button.
CIB MCMB
5E1/T1 Test MMI
MEIB
5E1/T1
T150 IDU
ZTE CABINETS
CIB PWR Board) CIFB (CTU Interface implements the signal conversion between CMB and the bottom interface. 48V MCMB
5E1/T1 Test MMI
Heater
MEIB
5E1/T1
48V
T150 IDU
ZTE CABINETS
MEIB (Micro Base Station E1 Interface Board) performs the following functions: Provides circuit impedance matching for CIB five E1/T1 channels. PWR Maximum three E1/T1 channels can be MCMB used to connect embedded transmission equipment (optical or microwave Test transmission). Maximum three can be 5E1/T1 used for cascading. 48V MEIB Provides link bypass function for E1/T1 Heater channels during the power down of 5E1/T1 cascading system (i.e. channel A bypass to channel C). T150 Provides lightening protection, and 48V signal isolation in the circuits. IDU It provides Abis interface board type information to CMB.
MMI
ZTE CABINETS
T150 is a PWR small capacity AU-4 path STM-1 level SDH equipment. It is usually used MCMB outdoors and is the auxiliary transmission equipment of GSM and CDMA BTSs. The Test function and interfaces are optimized5E1/T1 according to the48V actual requirement of MEIB HeaterSTM-1 GSM and CDMA. It provides (155520 Kbps) link, which is equal to the 5E1/T1 capacity of four E1 links.
CIB
MMI
48V
T150 IDU
ZTE CABINETS
10/09/2013
ZTE CABINETS
BTM B S C Abis T M M
TRM AEM
Um interface
CMM TRM
PSM
Heater
ZTE CABINETS
BTM B S C Abis T M M
TRM AEM
Um interface
CMM
The CMM (Controller & Maintenance PSM Module) implements such functions as Abis interface processing, BTS operation & Heater maintenance, clock synchronization and generation, internal/external alarm collection and processing.
TRM
ZTE CABINETS
BTM B S C Abis T M M
TRM AEM
Um interface
The BTM (Backboard Transmission CMM Module) is responsible for transmitting messages between the CMM, TRM and AEM and at the same time provides TRM interfaces for inputting and outputting PSM external signals.
Heater
ZTE CABINETS
BTM B S C Abis T M M
TRM AEM
Um interface
The TMM (Transmission Management CMM Module) is an outsourcing device, and the BS21 only provides one standard chassis (19 inches 3U) used for theTRM built-in SDH, microwave PSM and other transmission equipment.
Heater
ZTE CABINETS
10/09/2013
ZTE CABINETS
BTM B S C Abis T M M
TRM AEM
Um interface
CMM TRM
PSM
Heater
ZTE CABINETS
10/09/2013
Thank you!