Documente Academic
Documente Profesional
Documente Cultură
Prepared By
PRABHU KUMAR SURARAPU
Assistant Professor
Department of Electronics and Communication
Vel Tech Dr.RR&Dr.SR Techincal University
Chennai
U4ECB10
Page 2
U4ECB10
EXP NO:1
AIM:
To design an Inverting and noninverting Amplifier for the given specifications using Op-Amp IC
741.
THEORY:
The inverting amplifier is shown in the following Fig1.1.
invertinginput of the op-amp through resistor R1 . The op-amp has an open-loop gain of A, so
that the output signal is much larger than the error voltage. Because of the phase inversion, the
output signal is 180 out-of-phase with the input signal. This means that the feed back signal
opposes the input signal and the feedback is negative or degenerative.
Figure 1.1
Basic Inverting Amplifier
Page 3
U4ECB10
PIN DIAGRAM:
Figure 1.2
Pin diagram of IC 741
DESIGN:
We know for an inverting Amplifier ACL = RF / R1
Assume R1 ( approx. 10 K ) and find Rf
Hence Vo = - ACL Vi .
Design the Inverting amplifier with the specifications: 1. R1=5 K,2.R1=2 K and 3.22 K
CIRCUIT DIAGRAM
Figure 1.3
Inverting Amplifier Connection Diagram
APPARATUS REQUIRED:
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 4
U4ECB10
S.No
1.
2.
3.
4.
5.
6.
7.
Range
3 MHz
30 MHz
0 30 V
IC 741
As per requirement
As per design
As required
Quantity
1
1
1
1
1
As per design
As required
PROCEDURE:
1. Connections are given as per the circuit diagram.
2. + Vcc and - Vcc supply is given to the power supply terminal of the Op-Amp IC.
3. By adjusting the amplitude and frequency knobs of the function generator,
appropriate input voltage is applied to the inverting input terminal of the Op-Amp.
4.
The output voltage is obtained in the CRO and the input and output voltage
waveforms are plotted in a graph sheet.
THEORY:
NON-INVERTING AMPLIFIER:
A typical non-inverting amplifier with input resistor R1 and a feedback resistor Rf is shown in the
following figure 1.5 . The input voltage is given to the positive terminal.
V O=(1+ (R f / R1))Vid
DESIGN:
Page 5
U4ECB10
Figure 1.4
Non Inverting Amplifier Connection Diagram
OBSERVATION TABLE:
S.No
1.
2.
Input
Output
Practical
Theoretical
Amplitude
( No. of div x Volts per div )
Time period
( No. of div x Time per div )
MODEL GRAPH
(Inverting Amplifier)
Page 6
U4ECB10
Figure 1.5(a)
Figure 1.5(b)
MODEL GRAPH:
(Non inverting amplifier)
Figure 1.6(a)
Input wave form
Figure 1.6(b)
Output wave form
Page 7
U4ECB10
RESULT:
The design and testing of the inverting and non inverting
Page 8
U4ECB10
EXP.NO: 1(b)
AIM:
To construct an Adder and Subtractor using OP-AMP and verify its working.
THEORY:
ADDER:
The gain for each input to the adder depends upon the ratio of the feedback resistance
of the circuit to the value of the resistor at that input. The adder is sometimes called a weighted
adder because it provides a means of multiplying each of the inputs by a separate constant
before adding them all together. It can be used to add any number of inputs and multiply each
input by a different constant. This makes it useful inapplications like audio mixers.
Figure 2.1
Circuit diagram for Adder
Its behavior is governed by the following equation:
Page 9
U4ECB10
SUBTRACTOR:
It amplifies the difference between the two input voltages by Rf/Rin, which is the
overall gain for the circuit. Note that the ability of this amplifier to effectively take the
difference between two signals depends on the fact that it uses two pairs of identical
resistances. Also note that the signal that is subtracted goes into the negative input to the opamp. Be careful with the term differential. In spite of its similarity to the term
differentiation, the differential amplifier does not differentiate its input.
The circuit in the following Figure 12.2 is a differential amplifier, also called a
difference amplifier.
Figure 2.2
Circuit Diagram for Sub tractor
Its behavior is governed by the following equation:
Page 10
U4ECB10
CIRCUIT DIAGRAM:
ADDER:
SUBTRACTOR:
Page 11
U4ECB10
APPARATUS REQUIRED:
S.No
1.
2.
3.
4.
5.
6.
7.
Range
3 MHz
30 MHz
0 30 V
IC 741
2K
As required
Quantity
2
1
1
1
1
4
-
PROCEDURE:
1. Connections are given as per the circuit diagram.
2. + Vcc and - Vcc supply is given to the power supply terminal of the Op-Amp IC.
3. The output voltage is obtained in the CRO and the input and output voltage waveforms
are plotted in a graph sheet.
RESULT:
The Adder and Subtractor circuits are constructed and their functions are verified.
VIVA QUESTIONS:
1. Is it possible to construct an adder in non-inverting mode? How?
2. Why same values of resistors are used in the circuits?
3. Can you construct an Adder just with resistors?
4. Is your subtractor same as Differential amplifier? How?
Page 12
U4ECB10
EXP NO:2
AIM:
To design a Integrator and Differentiator circuit for the given specifications using Op-Amp IC
741.
DIFFERENTIATOR
THEORY:
Here the negative sign indicates that the output voltage is 1800out of phase with the
input signal.
A resistor Rcomp = Rf is normally connected to the non-inverting input terminal of the opamp to compensate for the input bias current. A workable differentiator can be
designed by implementing the following steps:
1. Select fa equal to the highest frequency of the input signal to be differentiated. Then,
assuming a value of C1< 1 F, calculate the value of Rf.
2. Choose fb= 20 fa and calculate the values of R1 and Cf so that R1C1 = Rf Cf.
Page 13
U4ECB10
DIFFERENTIATOR DESIGN:
[To design a differentiator circuit to differentiate an input signal that varies in frequency from 10
Hz to about 1 KHz.
Page 14
U4ECB10
CIRCUIT DIAGRAM:
Figure 2.1
Differentiator Connection Diagram
APPARATUS REQUIRED:
S.No
1.
2.
3.
4.
5.
6.
7.
8.
Range
3 MHz
30 MHz
0 30 V
IC 741
As per design
As per design
As required
Quantity
1
1
1
1
1
As per design
As per design
As required
PROCEDURE:
1. Connections are given as per the circuit diagram.
2. + Vcc and - Vcc supply is given to the power supply terminal of the Op-Amp IC.
3. By adjusting the amplitude and frequency knobs of the function generator, appropriate
input voltage is applied to the inverting input terminal of the Op-Amp.
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 15
U4ECB10
4. The output voltage is obtained in the CRO and the input and output voltage waveforms
are plotted in a graph sheet.
INTEGRATOR
THEORY:
A circuit in which the output voltage waveform is the integral of the input voltage
waveform is the integrator.
Here the negative sign indicates that the output voltage is 180
signal.
Normally between fa and fb the circuit acts as an integrator. Generally, the value of fa<
fb . The input signal will be integrated properly if the Time period T of the signal is larger
than or equal to Rf Cf . That is,
T Rf Cf
INTEGRATOR
DESIGN:
In the circuit of figure 2.2.(a),R1 Cf =1 second, and the input is a step (dc) voltage,2V. Determine
the output voltage.
Let the input function is constant beging at t=0 second ,0<=t<=4
Given Vin=2V
V0 =- 2 dt (t=0 to 4)
=(2+2+2+2)
=-8V
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 16
U4ECB10
CIRCUIT DIAGRAM:
INTEGRATOR
Figure 2.2
Integrator Connection Diagram
APPARATUS REQUIRED:
S.No
1.
2.
3.
4.
5.
6.
7.
8.
Range
3 MHz
30 MHz
0 30 V
IC 741
10K
0.1f
As required
Quantity
1
1
1
1
1
1
1
As required
PROCEDURE:
1. Connections are given as per the circuit diagram.
2. + Vcc and - Vcc supply is given to the power supply terminal of the Op-Amp IC.
Page 17
U4ECB10
3. By adjusting the amplitude and frequency knobs of the function generator, appropriate
input voltage is applied to the inverting input terminal of the Op-Amp.
4. The output voltage is obtained in the CRO and the input and output voltage waveforms
are plotted in a graph sheet.
OBSERVATION TABLE: (Differentiator)
S.No
1.
2.
Input
Output
Amplitude
( No. of div x Volts per div )
Time period
( No. of div x Time per div )
OBSERVATION TABLE:(Integrator)
S.No
1.
2.
Input
Output
Amplitude
( No. of div x Volts per div )
Time period
( No. of div x Time per div )
MODEL GRAPH:
DIFFERENTIATOR
Page 18
U4ECB10
Figure 2.3
Figure 2.4
MODEL GRAPH
Figure 2.2(b)
Input and output wave form
Page 19
U4ECB10
VIVA QUESTIONS:
1. What is integrator?
2. Write the disadvantages of ideal integrator?
3. What is differentiator?
4. What will happen if R1 not present?
5. Write the application of differentiator?
6. Why compensation resistance is needed in differentiator.?
7. Why integrators are preferred over differentiators in analog comparators?
Page 20
U4ECB10
EXP NO: 3
AIM:
To design and test the operation of Differential amplifier and Schmitt trigger.
DIFFRENTIAL AMPLIFIER
THEORY:
A Circuit that amplifies the difference between two signals is called a differential
amplifier.
For differential amplifier, though the circuit is not symmetric, but because of the
mismatch, the gain at the output with respect to positive terminal is slightly different in
magnitude to that of negative terminal.
So even with the same voltage applied to both the inputs, the output is not zero.
Page 21
U4ECB10
Figure 3.1
Differential Amplifier connection diagram
APPARATUS REQUIRED:
S.No
Name of the Apparatus
1.
Function Generator
2.
CRO
3.
Dual RPS
4.
Op-Amp
5.
Bread Board
6.
Resistors
7.
Connecting wires and probes
PROCEDURE:
Range
3 MHz
30 MHz
0 30 V
IC 741
As per design
As required
Quantity
2
1
1
1
1
As per design
As required
VI(V)
V2(V)
VO(V)
NO
Page 22
U4ECB10
SCHMITT TRIGGER
THEORY:
The Schmitt trigger is a comparator with positive feedback. It converts slowly varying
waveforms into square wave.
The input voltage is applied to the inverting terminal and the feedback circuit is
connected to the non-inverting terminal. The input voltage triggers the output every
time it exceeds certain voltage levels.
These voltage levels are called as upper threshold voltage (VUT) and lower threshold
voltage (VLT). As long as the input voltage is less than VUT the output remains at +Vsat.
When Vi is just greater than VUT, the output regenerative switches to - Vsat and remains
at this level. When the input voltage becomes lesser than VLT, the output switches from Vsatto + Vsat.
FORMULA:
R2
Vsat
VUT
R
R
1
2
R2
( Vsat )
VLT
R1 R2
SCHMITT TRIGGER DESIGN:
Vsat=0.9Vcc=0.9X12V=10.8V
To find R1 and R2 values
Choose R2 = 1K
R1 Vsat
1
R2 VUT
R1 = 47K for VUT = 0.225V
Page 23
U4ECB10
Figure 3.2
Schmitt Triger
PROCEDURE:
1. Connect the circuit as per the circuit diagram.
2. Set the input voltage as 1Vpp.
3. Measure the amplitude of the output signal.
4. Note down the upper and lower threshold voltages by superimposing the square wave
on the input sine wave.
5. Plot the input and output waveforms.
TABULATION: Schmitt Triger
Waveform
Nature
Input waveform
Sine wave
Output waveform
Square wave
Amplitudes(Volts)
Time period(ms)
Page 24
U4ECB10
MODEL GRAPH:
Figure 3.3
Schmitt trigger output graph
RESULT:
VIVA QUESTIONS:
1.
2.
3.
4.
5.
6.
7.
What is hysteresis?
8.
9.
10.
11.
Define CMRR.
12.
Page 25
U4ECB10
EXP NO: 4
AIM:
To design the Wien Bridge and Phase shift oscillator using OP-AMP IC for the given
specification.
WEIN BRIDGE
THEORY:
The Wien bridge oscillator is the most commonly used audio frequency oscillator
because of its simplicity and stability. Figure shows the Wien bridge oscillator in which
Wien bridge circuit is connected between the amplifiers input terminals and the output
terminal. The bridge has a series RC network in one arm and a parallel RC network in the
adjoining arm. In the remaining two arms of the bridge, resistors R1 and Rf are
connected.
The phase angle criterion for oscillation is that the total phase shift around the circuit
must be 00. This condition occurs only when the bridge is balanced. The frequency of
oscillation fois exactly the resonant frequency of the balanced Wien bridge and is given
by, fo = 1/(2 R C )
WEIN BRIDGE
DESIGN
fo=1kHz
fo = 1/(2 R C ) and Rf = 2R1
Choose C=0.05 F
So R= 1/ (2 10000.05 F) =3.1K
Take R1=10R=30 K and
Rf=2R1= 60 K (use100 K pot to get the exact value by varying the pot)
1. Design the oscillator that f0 =965Hz
Page 26
U4ECB10
CIRCUIT DIAGRAM
Figure 4.1
Wien Bridge Oscillator
APPARATUS REQUIRED:
S.No
Name of the Apparatus
1.
Function Generator
2.
CRO
3.
Dual RPS
4.
Op-Amp
5.
Bread Board
6.
Resistors
7.
Capacitors
8.
Connecting wires and probes
Range
3 MHz
30 MHz
0 30 V
IC 741
As per design
As per design
As required
Quantity
2
1
1
1
1
As per design
As per design
As required
PROCEDURE:
1. Construct the circuit with the values obtained in the design.
2. Observe the output wave form on an Oscilloscope.
3. Measure the frequency of oscillator and voltage amplitude.
Model Graph:
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 27
U4ECB10
Figure 4.2
Wein bridge Output graph
phase-shift oscillator
THEORY:
A phase-shift oscillator is a linear electronic oscillator circuit that produces a sine wave output.
It consists of an inverting amplifie
amplifier element such as a transistor or op amp with its output fed
back to its input through a phase
phase-shift network consisting of resistors and capacitors. The
feedback network 'shifts' the phase of the amplifier output by 180 degrees at the oscillation
frequency to give positive feedback
feedback. Phase-shift oscillators are often used at audio
udio frequency as
audio oscillators.
CIRCUIT DIAGRAM:
Figure 4.3
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 28
U4ECB10
Figure 4.4
RC Phase shift oscillator output graph
TABULATION:
AMPLITUDE (V)
TIME PERIOD
FREQUENCY
Page 29
U4ECB10
RESULT:
VIVA QUESTIONS:
1. What happens at the output if Rf is changed?
2. How is phase shift oscillator different from RC phase shift oscillator?
3. What are the applications of phase shift oscillator?
4. What happens at the output if Rf is changed?
5. How is Wein bridge oscillator different from RC phase shift oscillator?
6. What are the applications of Wein bridge oscillator?
7. What is the condition for the bridge to be balanced?
Page 30
U4ECB10
EXP NO:5
AIM:
To design and construct an Astable and Monostable multivibrators using IC Operational
amplifier 741.
ASTABLE MULTIVIBRATOR
THEORY:
Multivibrators are group of regenerative circuits. They are widely used in timing
applications.
An electronic circuit that generates square waves (or other non-sinusoidal such a
rectangular, saw tooth waves) is known as a multivibrator.
ASTABLE MULTIVIBRATOR:
Astable circuits are used to generate square waves. It is also known as free running
multivibrator.
The circuit has two quasi stable states (no stable state). Thus, there is an oscillation
between two states and no external signals are required to produce the change in state.
OPERATION:
In a free running mode, the two states of the multivibrator are momentarily stable and
the circuit switches respectively between these two states.
Page 31
U4ECB10
In one state the amplifier output goes to positive saturation level while in the other
state it goes into negative saturation. The amplifier output is thus a square wave; the
period of a square wave is determined by the time constant R & C.
Figure 5.1
ASTABLE MULTIVIBRATOR USING OP AMP Circuit Diagram
Page 32
U4ECB10
APPARATUS REQUIRED:
S.No
1.
2.
3.
4.
5.
6.
7.
8.
Range
3 MHz
30 MHz
0 30 V
IC 741
As per design
As per design
As required
Quantity
2
1
1
1
1
As per design
As per design
As required
PROCEDURE:
1. Get the required components and check the condition of them.
2. Connect the circuit as per the circuit diagram.
3. Switch on the power supply and look at the output with CRO.
4. Measure the width and time period of the output waveform.
5. Look at the voltage across the capacitor, an exponentially rising and falling wave
between 5V and 10V is noted.
6. After completing the experiments, reduce the supply to zero potential and disconnect
the circuit diagram.
OBSERVATION TABLE:
Parameters
Amplitude(Volts)
Time period(ms)
Output voltage
Capacitor voltage
Page 33
U4ECB10
Figure 5.2
MONOSTABLE
THEORY:
It is also known as one shot multivibrator.
The circuit remains in a quasistable state for a fixed interval of time and then reverts to
its original stable state.
An internal trigger signal is generated which produces the transition to the stable state.
Usually, the charging and discharging of a capacitor provides this internal trigger signal.
MONOSTABLE DESIGN:
SPECIFICATION:
Vcc = 10V, V (Sat) = 10V, pulse width T = 1msec
1. To find R1 and R2
= R1 R1+R2
Assume R1=R2, so = 0.5
2. To find charging period of capacitor,
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 34
U4ECB10
R2 = R1=10k.
T = R * C (0.69)
T = 0.69 RC
Choose T = 1ms, & C = 0.1f, find out the value of R, Therefore R = 12kohms.
CIRCUIT DIAGRAM:
Figure 5.3
Monostable Multivibrator
PROCEDURE:
1. Get the required components and check the condition of them.
2. Connect the circuit as per the circuit diagram.
3. Switch on the power supply and look at the output with CRO.
4. Measure the width and time period of the output waveform.
Page 35
U4ECB10
OBSERVATION TABLE:
Parameters
Amplitude(Volts)
Time period(ms)
Output voltage
Capacitor voltage
MODEL GRAPH:
Figure 5.4
Monostable multivibrator Output graphs
RESULT:
VIVA QUESTIONS:
1. What is a multivibrator?
2. Give the principle of operation of Multivibrators?
3. What is another name for astable multivibrator?
4. What do you mean by astable multivibrator?
5. Differentiate astable and monostable multivibrator?
6. Give the application of astable multivibrator.
Page 36
U4ECB10
Page 37
U4ECB10
EXP NO: 6 SECOND ORDER ACTIVE LOW PASS HIGH PASS AND BAND PASS FILTER
AIM:
To design a second order low pass, high pass and band pass filter and also to
THEORY:
LOWPASS FILTER:
An improved filter response can be obtained by using a second order active filter. A second
order filter consists of two RC pairs and has a roll-off rate of -40 dB/decade. A general second
order filter (Sallen Kay filter) is used to analyze different LP, HP, BP and BSF.
HIGHPASS FILTER:
The high pass filter is the complement of the low pass filter. Thus the high pass filter canbe
obtained by interchanging R and C in the circuit of low pass configuration. A high pass
filterallows only frequencies above a certain bread point to pass through and it terminates the
lowfrequency components. The range of frequencies beyond its lower cut off frequency fL is
calledstop band.
BANDPASS FILTER:
The BPF is the combination of high and low pass filters and this allows a specified range of
frequencies to pass through. It has two stop bands in range of frequencies between 0 to fL
andbeyond fH. The band b/w fL and fH is called pass band. Hence its bandwidth is (fL-fH). This
filter has a maximum gain at the resonant frequency (fr) which is defined as
Page 38
U4ECB10
DESIGN:
Given: fH = 1 KHz = 1/ (2RC)
Let C = 0.1 F, R = 1.6 K
For n = 2, (damping factor) = 1.414,
Pass band gain = Ao = 3 - =3 1.414 = 1.586.
Transfer function of second order Butterworth LPF as:
1.586
H(s) = --------------------------S2 + 1.414 s + 1
Now
Page 39
U4ECB10
HPF:
Figure 6.2
High pass filter connection Diagram
BPF:
Figure 6.3
Band pass filter connection Diagram
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 40
U4ECB10
APPARATUS REQUIRED:
S.No
Name of the Apparatus
1.
Function Generator
2.
CRO
3.
Dual RPS
4.
Op-Amp
5.
Bread Board
6.
Resistors
7.
Capacitors
8.
Connecting wires and probes
Range
3 MHz
30 MHz
0 30 V
IC 741
As per design
As per design
As required
Quantity
2
1
1
1
1
As per design
As per design
As required
PROCEDURE:
1. The connections are made as shown in the circuit diagram.
2. The signal which has to be made sine is applied to the RC filter pair circuit with the noninverting terminal.
3. The supply voltage is switched ON and the o/p voltages are recorded through CRO by
varying different frequencies and tabulate the readings.
4. Calculating Gain through the formula and plotting the frequency response
characteristics using Semi-log graph sheet and finding out the 3 dB line for fc.
MODEL GRAPH:
LPF:
Frequency Response Characteristics: (Use Semi log Graph):
Gain
In
dB
- 3 dB
fc = 1KHz
Frequency (Hz)
Figure 6.4
Page 41
U4ECB10
HPF:
Figure 6.5
BPF:
Figure 6.6
Page 42
U4ECB10
OBSERVATION TABLE:
VIN =
S.No.
FREQUNCY
Hz
Volts
O/P voltage
(VO )Volts
RESULT:
VIVA QUESTIONS:
1. What is pass band and stop band?
2. What has to be done in the circuit, if you want your filter to exactly follow the cut-off
frequency?
3. Can a Band pass filter be constructed just by coupling a low pass filter and high pass
filter, how?
4. Why do we draw a line at 3 dB below the peak gain to calculate the pass band of a filter?
Page 43
U4ECB10
EXP NO: 7
AIM
To design and test a 4 bit Successive approximation type A/D and 3 bit R-2R ladder D/A
converter
THEORY
The analog to digital converter is normally required at the input of a digital system for
the measurement or control of analog quantities. In A/D converters, the input is an analog
voltage and the output is a digital code. A/D converters are more complex and time consuming
than D/A converters.
A/D converters can be designed with or without the use of D/A converters as part of
their circuitry. The commonly used types of A/D converters are
(a) Successive- approximation converter
(b) Counting or digital ramp converter.
PROCEDURE
1. Make the connections as per the circuit diagram.
2. Switch on the power supply.
3. Give voltage to the IC.
4. Note the sequence of LED blinking.
APPARATUS REQURIED
SL. No
Apparatus
Range
Qty
1.
Operational amplifier
IC 741
2.
RPS
(0-30V)
3.
Resistors
1k,
20k
1
4
Page 44
U4ECB10
CIRCUIT DIAGRAM
Figure 7.1
Schematic Diagram for A/D converter
APPARATUS REQUIRED:
S.No
Apparatus
Range
Qty
4.
Operational amplifier
IC 741
5.
RPS
(0-30V)
6.
Resistors
Each 1
Each 4
7.
Voltmeter
(0-10V)MC
Page 45
U4ECB10
D/A
THEORY
The decoder is one, which converts the digital information from the digital processing
unit to analog output. We call the digital to analog converter or in short D/A converter. The D/A
converter decode the digital information to analog form.
The input to a digital to analog converter is a binary signal available in parallel form.
These digital signals are available at the output of the latches or registers and correspond to
logic 0 and logic 1. These voltages are not directly applied to the converter but are used to
operate digitally controlled switches. The switch is put into two positions depending on the
digital signal 1 or 0, which connect the fixed voltages. Let us suppose we want to convert the
binary form the processing unit to a 0 to 3 volts output. We must first set up a truth table for all
possible situations. The following table shows four inputs into a D/A converter.
PROCRDURE
1. Make the connections as per the circuit diagram.
2. Switch ON the power supply.
3. Set the digital input by using switches SW1 to SW8
4. The output analog equivalent for the digital data can be viewed from pin6
5. Verify the analog output theoretically by sing the formula given below
6. Repeat the steps 4 to 6 for different digital inputs
FORMULA USED
Vanalog = VR [(b1 . 21 ) + (b . 2 ) + (b3 . 23 ) + + (bn . 2n )]
Where,
Page 46
U4ECB10
CIRCUIT DIAGRAM
Figure 7.2
D/A Converter circuit diagram
RESULT
Thus the R-2R ladder DAC and a binary weighted DAC has been tested for various digital inputs.
Page 47
U4ECB10
EXP NO: 8
AIM:
To design, construct and test the astable multivibrator and monostable multivibrator using
IC 555.
THEORY:
IC555 is a combination of linear comparators and digital flip flops. The output of
comparators is used to set/reset the FF.
The output FF circuit is brought out through an amplifier stage. The FF output is also
give to a transistor to discharge a timing capacitor.
The 555 timer has two basic operational modes: astable and monostable.
Astable operation:
The capacitor charges toward the supply voltage through the two resistors, R1 and R2.
The discharge pin (7) connected to the internal transistor is connected to the junction of
those two resistors.
Monostable operation:
The trigger input is initially high (about 1/3 of +V). When a negative-going trigger pulse
is applied to the trigger input, the threshold on the lower comparator is exceeded.
The lower comparator, therefore, sets the flip-flop. That causes T1 to cut off, acting as
an open circuit. The setting of the flip-flop also causes a positive-going output level
which is the beginning of the output timing pulse.
The capacitor now begins to charge through the external resistor. As soon as the charge
on the capacitor equal 2/3 of the supply voltage, the upper comparator triggers and
resets the control flip-flop.
Page 48
U4ECB10
That terminates the output pulse which switches back to zero. At this time, T1 again
conducts thereby discharging the capacitor.
Whenever a trigger pulse is applied to the input, the 555 will generate its singleduration output pulse. Depending upon the values of external resistance and
capacitance used, the output timing pulse may be adjusted and the duration of the
output pulse is approximately equal to T = 1.1 x R x C
DESIGN:
ASTABLE MULTIVIBRATOR:
T= 0.693(RA+2RB) C
0.7 (RA+2RB) C
Let RA=RB=R
T= 2.1 RC
Assume R=10K and C = 0.1F for T=2.1msec
Also TON = 0.7(RA+RB)C =1.4msec
TOFF = 0.7RBC=0.7msec
MONOSTABLE MULTIVIBRATOR:
TON= 1.1 RC
Assume R=10K and C=0.1F for TON=1.1msec
CIRCUIT DIAGRAM
ASTABLE MULTIVIBRATOR
Figure 8.1
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 49
U4ECB10
MONOSTABLE MULTIVIBRATOR
APPARATUS REQUIRED:
S.No
1.
2.
3.
4.
5.
6.
7.
8.
Figure 8.2
Range
3 MHz
30 MHz
0 30 V
IC 741
As per design
As per design
As required
Quantity
1
1
1
1
1
As per design
As per design
As required
PROCEDURE:
1. Connect the circuit as per the circuit diagram.
2. Measure the width and time period of the output waveform.
3. Observe the voltage across the capacitor and note down the amplitude.
4. Tabulate the readings
5. Plot the graph
Page 50
U4ECB10
TABULATION:
ASTABLE MULTIVIBRATOR :
PARAMETERS
AMPLITUDE(VOLTS)
TIME PERIOD(MS)
OUTPUT VOLTAGE
CAPACITOR VOLTAGE
MONOSTABLE MULTIVIBRATOR :
PARAMETERS
AMPLITUDE(VOLTS)
TIME PERIOD(MS)
OUTPUT VOLTAGE
CAPACITOR VOLTAGE
MODEL GRAPH:
ASTABLE MULTIVIBRATOR
Figure 8.3
Page 51
U4ECB10
MONOSTABLE MULTIVIBRATOR
Figure 8.4
RESULT:Thus the design of Astable multivibrator and Monostable multivibrator was done and
output was verified.
VIVA QUESTIONS:
1. What are the modes of operation of 555 timers?
2. Explain the function of reset.
3. Define duty cycle.
4. Mention the applications of IC555.
5. Give the methods for obtaining symmetrical square wave.
6. What is the other name for monostable multivibrator?
7. Explain the operation of IC555 in astable mode.
8. Explain the operation of IC555 in monostable mode.
9. Why negative pulse is used as trigger?
10. What is the charging time for capacitor in monostable mode?
Page 52
U4ECB10
EXP.NO:9
AIM:
To study the operation of NE 565 PLL as a frequency multiplier.
THEORY:
Figure shows the block diagram of a frequency multiplier using the 565 PLL. The frequency
counter is inserted between the VCO and the phase comparator. Since the output of the divider
is locked to the input frequency fIN, the VCO is actually running at a multiple of the input
frequency.
The desired amount of multiplication can be obtained by selecting a proper divide by N
network, where N is an integer. For example, to obtain the output frequency fOUT =5 fIN, a divide
by N = 5 network is needed. The 4 bit binary counter (7490) is configured as a divide by 5
circuit. The transistor Q is used as a driver stage to increase the driving capability of the NE 565.
C3 is used to eliminate possible oscillation. C2 should be large enough to stabilize the VCO
frequency.
BLOCK DIAGRAM:
Figure 9.1
Block Diaram for PLL
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 53
U4ECB10
CIRCUIT DIAGRAM:
Figure 9.2
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 54
U4ECB10
APPARATUS REQUIRED:
S.NO
ITEM
RANGE
QTY
IC
IC NE565
IC 7490
1
1
Resistors
As required
3
4
Capacitor
CRO
As required
30MHz
RPS
DUAL(0-30) V
Transistor
2N3391
Bread Board
8.
Connecting wires
As required
PROCEDURE:
1. Connect the circuit as shown in figure.
2. The free running frequency fOUT of VCO is varied by adjusting R1 and C1 and the output
frequency is determined and it should be 5 times the input frequency.
3. Determine the output frequency for different input frequency of 1 KHz and 1.5 KHz.
TABULATION:
INPUT
AMPLITUDE
OUTPUT
FREQUENCY
AMPLITUDE
FREQUENCY
RESULT:
The frequency multiplier using PLL principle is studied and the output waveform is observed.
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 55
U4ECB10
VIVA QUESTIONS:
1. What are the other applications of PLL?
2. Explain the working of the transistor 2N3391?
3. What is VCO? Explain its working.
4. What are the characteristics of PLL?
5. What is IC 7490?
Page 56
U4ECB10
EXP NO:10
AIM:To design an Instrumentation Amplifie for the given specifications using Op-Amp IC 741.
THEORY:
An instrumentationamplifier is a type of differential amplifier that has been outfitted with input
buffers, which eliminate the need for input impedance matching and thus make the amplifier
particularly suitable for use in measurement and test equipment.
Although the instrumentation amplifier is usually shown schematically identical to a standard
op-amp, the electronic instrumentation amp is almost always internally composed of 3 opamps. These are arranged so that there is one op-amp to buffer each input (+,), and one to
produce the desired output with adequate impedance matching for the function.
Figure 3.1
Typical instrumentation amplifier schematic
Page 57
U4ECB10
The most commonly used instrumentation amplifier circuit is shown in the figure. The gain of
the circuit is
The rightmost amplifier, along with the resistors labeled R2 and R3 is just the standard
differential amplifier circuit, with gain = R3 / R2 and differential input resistance = 2R
2 2. The two
amplifiers on the left are the buffers. With Rgain removed (open circuited), they are simple unity
gain buffers; the circuit will work in that state, with gain simply equal to R3 / R2 and high input
impedance
nce because of the buffers. The buffer gain could be increased by putting resistors
between the buffer inverting inputs and ground to shunt away some of the negative feedback;
however, the single resistor Rgain between the two inverting inputs is a much more
mo elegant
method: it increases the differential
differential-mode
mode gain of the buffer pair while leaving the commoncommon
mode gain equal to 1. This increases the common
common-mode
mode rejection ratio (CMRR) of the circuit
and also enables the buffers to handle much larger common
common-mode signals without clipping than
would be the case if they were separate and had the same gain. Another benefit of the method
is that it boosts the gain using a single resistor rather than a pair, thus avoiding a resistorresistor
matching problem (although the two R1s need to be matched), and very conveniently allowing
the gain of the circuit to be changed by changing the value of a single resistor. A set of switchswitch
selectable resistors or even a potentiometer can be used for Rgain, providing easy changes to the
gain of the circuit, without the complexity of having to switch matched pairs of resistors.
The ideal common-mode
mode gain of an instrumentation amplifier is zero. In the circuit shown,
common-mode
mode gain is caused by mismatches in the values of the equally
equally-numbered
numbered resistors
and by the mis-match
match in common mode gains of the two input op
op-amps.
amps. Obtaining very closely
matched resistors is a significant difficulty in fabricating these circuits, as is optimizing the
common mode performance of the input op
op-amps.
Page 58
U4ECB10
An instrumentation
entation amp can also be built with 2 op
op-amps
amps to save on cost and increase CMRR,
but the gain must be higher than 2 (+6 dB).
Design :
Design the instrumentation amplifier having overall gain of 100
Stage1:let AV1 =AV2
A=Suare root of (100)
=10
Stage 2:Designing the resistor values:
Asuume =R3/ R2 =10; and (1+2R/Rgain) = 10; taking R2 =1k ,R3 =10
Taking Rgain=10k
on solving R1 =4.5 k
1.Design
Design the instrumentation ampl
amplifier having overall gain of 25.
2. Design the instrumentation ampl
amplifier having overall gain of 81.
3. Design the instrumentation ampl
amplifier having overall gain of 225.
Page 59
U4ECB10
CIRCUIT DIAGRAM:
Figure 3.2
Instrumentation Amplifier
APPARATUS REQUIRED:
S.No
1.
2.
3.
4.
5.
6.
7.
Range
3 MHz
30 MHz
0 30 V
IC 741
As per design
As required
Quantity
2
1
1
1
1
As per design
As required
Page 60
U4ECB10
PROCEDURE:
1.Patch the connections and connect the design resistance Rg extending to have the desired
gain.
2.Measure the input voltage at Vin1 and Vin2 using digital multimeter.
3.The difference in Vin2- Vin1 is amplified and indicated in LCD display.
4.Check the theoretical value with the experimental value.
TABULATION:
S.No
THEORETICAL VALUE
GAIN
VIN1
VIN2
VIN2 - VIN1
SETTING (mv)
(mv)
Vout
(mv)
PRACTICAL VALUE
GAIN = Vout/ VIN2 - VIN1
RESULT:
Thus the instrumentation amplifier with digital indication was designed and the working of this
was studied.
VIVA QUESTIONS:
1. Why the above circuit is called Instrumentation amplifier?
2. What would happen if the Op-amps were fed back positively, in the above circuit?
3. What changes would you get if you increase or decrease the Rgainvalue?
4. What happens to the output when you change the values of R1, R2, and R3
separately?
5. What is the difference between Instrumentation amplifier and Differential amplifier?
Page 61
U4ECB10
EXP NO:
VOLTAGE REGULATORS
AIM:
1) To design a adjustable voltage regulator using IC LM 317 to vary the output from 1V to
4V.
2) To design a voltage regulator to give output voltage of 4-5V using LM723.
THEORY:
The internal circuitry of the LM317 can only handle 1.5 A of current as an absolute
maximum.
The LM317 is a linear regulator. This means that it dissipates the excess voltage as heat,
with more heat produced as the voltage is set lower and lower. Thus heat sink must be
mounted on the regulator that is capable of dissipating the heat produced.
but external transistors can be added to provide any desired load current. The circuit
features extremely low standby current drain, and provision is made for either linear or
fold back current limiting.
The LM723/LM723C is also useful in a wide range of other applications such as a shunt
regulator, a current regulator or a temperature controller.
DESIGN:
CALCULATION:
LM317
The output voltage of the LM317 is
Vout = 1.25V * (1 + R2/R1) + Iadj * R2
If Iadj is negligible then
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 62
U4ECB10
= 1.81V.
CIRCUIT DIAGRAM:
LM317
Figure 10.1
Voltage Regulator usnig LM317
APPARATUS REQUIRED:
APPARATUS
RANGE
QUANTITY
Power supply
(0-30v)
Resistors
5k,220
LM317
Voltmeter
1
(0-30v)
Page 63
U4ECB10
PROCEDURE:
1. Make the circuit connection as per the circuit diagram.
2. Set the amplitude of input signal as 12 Volt
3. Vary the DRB value.
4. Measure the output voltage.
5. Tabulate the readings.
TABULATION:
Adjustable DC Power supply using LM317
Vi=10Volts
Sl
DRB Value
No
in K
Theoretical
Practical
Page 64
U4ECB10
(II)LM 723
CIRCUIT DIAGRAM
Figure 10.2
Voltage Regulator Using LM 723
DESIGN:
LM723
Assume R3=1kohms, R4 = 2.2Kohms
Vo = 7.15[1 + (R3/R4)]
= 7.15[1 + (1/2.2)]
= 4.95V
Page 65
U4ECB10
APPARATUS REQUIRED:
S.No.
ITEM
SPECIFICATION
QTY
IC 723
Resistors
1kohms
Capacitors
100 pF,0.1microfarad
1 each
R. P. S
(0- 30) V, 1 mA
DRB
1,as
Connecting Wires
required
PROCEDURE:
1. Make the circuit connection as per the circuit diagram.
2. Set the amplitude of input signal as 12 Volt
3. Vary the DRB value.
4. Measure the output voltage.
5. Tabulate the readings.
DC Power supply using LM723
Vi=10 Volts
Sl
DRB Value
No
in K
Theoretical
Practical
Page 66
U4ECB10
Page 67
U4ECB10
EXP NO:
STUDY OF SMPS
AIM: Study the power supply ( SMPS) and their voltage levels by multi-meter with proper
attention to measure various voltage .
THEORY:
Switch mode power supplies (SMPS) have become the architecture of choice for power
conversion because of their economy, higher efficiency and lighter weight. In this lab you will
investigate the basic operating principles of a switch mode power supply, and then design,
build and test a simple supply given a few basic components.
A considerable amount of background theory and design advice is included following the
Procedure description below.
Block Diagram:
Figure 11.1
Block Diagram of SMPS
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 68
U4ECB10
Design Objective:
Your objective will be to build either a 5V or 12V, 5W regulated supply with a maximum
1% ripple at full load, maintained over a 10% input voltage variation. If the available
components are such that you must design for a slightly different output voltage, discuss this
change in objective with your supervisor. It is more important that you understand the design
process and characterize the supply you build than to have a specific output voltage. Note that
you will also have to test your supply to verify the specifications, and to characterize other
parameters such as its response to step changes in load current and how long it can maintain
the output if the input supply is interrupted.
SMPS Investigation and Analysis
The first part of this lab involves investigating the principles of operation of a SMPS and the
parameters that you will employ in the design.
Design and testing of a regulated SMPS
For the remainder of this lab, you will be asked to design, build and test a regulated Switch
Mode Power Supply. The restrictions you will be required to work within are as follows:
the input must be from the 120/24VAC step-down transformers available in the
laboratory
the integrated regulator circuit available to you is from STMicroelectronicss
UC384xB family: specifically, the UC3845B
RESULT:
The study of SMPS is done by measuring the quantities.
Page 69
U4ECB10
EXP NO:
Page 70
U4ECB10
DESIGN:
Given: fH = 1 KHz = 1/ (2RC)
Let C = 0.1 F, R = 1.6 K
For n = 2, (damping factor) = 1.414,
Pass band gain = Ao = 3 - =3 1.414 = 1.586.
Transfer function of second order Butterworth LPF as:
1.586
H(s) = --------------------------S2 + 1.414 s + 1
Now
Page 71
U4ECB10
HPF:
Figure 5.2
High pass filter connection Diagram
BPF:
Figure 5.3
Band pass filter connection Diagram
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 72
U4ECB10
APPARATUS REQUIRED:
S.No
Name of the Apparatus
1.
Function Generator
2.
CRO
3.
Dual RPS
4.
Op-Amp
5.
Bread Board
6.
Resistors
7.
Capacitors
8.
Connecting wires and probes
Range
3 MHz
30 MHz
0 30 V
IC 741
As per design
As per design
As required
Quantity
2
1
1
1
1
As per design
As per design
As required
PROCEDURE:
Solution:
1. Select programs->microsim eval8->design manager. click on tools->schematics. select draw>get new part->advanced.
2.To create the circuit we need a uA 741 op-amp, two dc supplies(VDC),four labels(GLOBAL),six
ground terminals(AGND),five resistors(R),two capacitors(c),and VAC. using part browser
advanced. select all the above parts one at a time and place them in the work space. now
close the get new part option by clicking on place and close.
3. Arrange the parts in the work area the way they appear. Interconnect the parts using draw>wire.
4.The parts in the circuit that require setting new attributes are the two dc supplies, five
resistors, two capacitors, and VAC.A parts attribute is changed by first double-clicking on the
part of the label and then entering the new value. set the attributes and change the attribute
values of above parts. Also,set the GLOBAL labels, two each as +Vcc and VEE. To set up VAC
attributes double-click on the symbol and then in pop-up window change magnitude and as
shown below.
ACMAG->1v->saveattr->change display->both name and value->0k
ACPHASE->0->save attr->0k
Add the location of V0 to the out of the circuit.
5. Since a plot of V0 versus frequency is desired,open analysis->probe setup and click on
automatically run probe after simulation.
6.Open analysis->setup->Enable AC sweep
Open AC sweep->decade
->pts/decade->10
->start freq->10HZ
->end freq->10HZ
7. Save the circuit as a file.
8.Open analysis->create netlist to make sure that there are no wiring errors.Aworning will
appear if there are any errors.click onOK ana a list ofthe error locations will be displayed.if
there are no errors,the circuit is ready for simulation.
VEL TECHDR.RR&DR.SR TECHNICAL UNIVERSITY
Page 73
U4ECB10
Gain
In
dB
- 3 dB
fc = 1KHz
Frequency (Hz)
HPF:
Page 74
U4ECB10
BPF:
RESULT:
Active filter are simulated by using Pspice and Characteristics are observed in the out put.
Page 75
U4ECB10
Page 76