Documente Academic
Documente Profesional
Documente Cultură
Living
Outside
Play
Technology
Workshop
Table of Contents
RUBBER BAND POWERED FOAM PLATE AIRPLANE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. THE ALL-IMPORTANT RUBBER BAND
2. 3 BENDY STRAWS (CAN BE NON-BENDY)
3. A MODEL PLANE PROPELLER (CAN BE FOUND IN HOBBY SHOPS)
4. 4 NON-BENDY STRAWS (CAN BE BENDY)
5. 2 PAPPER CLIPS (NEEDS TO BE 1 1/2" LONG)
6. A PIECE OF THIN CARD BOARD
7. 3 FOAM PLATES (NOT PAPER)
Image Notes
1. ALSO A PUSH-PIN...
2. TAPE
3. A PAIR OF SCISSORS
4. A ONE FOOT RULER WITH INCHES
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. THIS WILL END UP AS PART OF THE TAIL AND THE BODY OF THE PLANE
Image Notes
1. ONE WING
Image Notes
1. THE RUDDER.
2. PART OF THE TAIL.
3. PART OF THE BODY.
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Step 3: -CUTTING THE CARDBOARDLook at the pictures, in order from left to right, to see what you need to do in order to finish this step.
Image Notes
1. STEP A.
2. CUT ALONG THE BLACK LINES.
3. THIS SHOULD BE 1 INCH LONG.
Image Notes
1. THIS IS PART OF STEP A.
2. 2 INCHES HIGH.
Image Notes
1. STEP B.
2. CUT HERE...
3. AND HERE.
4. CUT HERE AS WELL...
5. AND HERE...
Image Notes
1. FOLD ON RED DOTS.
2. FOLD HERE.
3. STEP C.
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. PLACE TAPE HERE.
2. STEP D.
Image Notes
1. YOU MAY HAVE TO CUT PIECES OFF, OR YOU MAY NOT.
2. STEP E.
3. FOLD ALL 4 TABS AS SHOWN.
Image Notes
1. STEP F.
2. AFTER STEP E, IT SHOULD LOOK LIKE THIS.
Image Notes
1. STEP G.
2. END UP WITH THIS.
Image Notes
1. A PUSH-PIN
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Step 4: -THE PAPER CLIPLook at the pictures in order from left to right again...
Image Notes
1. THIS SIZE IS GOOD. (ABOUT 1 1/4 INCHES)
2. TOO SMALL...
3. TOO BIG...
Image Notes
1. UN-FOLD...
Image Notes
1. LENGTH = 3 1/4 INCHES
2. UN-FOLD SOME MORE...
Image Notes
1. PLACE INSIDE "THE BOX"
Step 5: -BUILDING THE TAIL & BODYOnce again look at the pictures to complete this step.
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. 3 STRAWS (BENDY OR NON BENDY, IT REALY DOES NOT MATTER)
2. PART OF THE FOAR PLATE YOU CUT EARLIER. (WILL END UP
SUPPORTING THE WINGS AND PROPELLER.)
3. TAIL SECTION... (MADE FROM FOAM PLATE.)
4. THE RUDDER.
Image Notes
1. TAPE HERE.... (THE BLACK LINES SHOW THE CORNERS AND EDGES
OF THE TAPE)
2. IF USING BENDY STRAWS, HAVE THE BENDY PART HERE.
Image Notes
1. TAPE
2. END OF SAME PIECE OF TAPE
3. MAKE SURE THIS IS A 90 DEGREE ANGLE
Image Notes
1. DO SAME HERE AS ON OTHER SIDE
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. ROLL TAPE AROUND THE STRAWS INCLUDEING THE 3RD BLUE STRAW
2. ROLL TAPE AROUND ALL 3 STRAWS HERE AS WELL
Image Notes
1. PLACE TAPE (X4) HERE.
Image Notes
1. CUT THIS OFF AND SAVE FOR LATER.
2. SHOULD BE SAME LENGTH
Image Notes
1. INSERT ONE STRAW INTO THE OTHER
Image Notes
1. TAPE SHOULD GO HERE...
2. TAPE HERE ALSO.
Image Notes
1. FLIP...
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. "THE BOX"
2. TAPE HERE TWICE...
3. AND HERE TWICE.
4. AFTER YOU HAVE "THE BOX" VERY SUCCURE, MAKE SURE PAPER CLIP
MOVES FREELY
Image Notes
1. WING ONE
2. WING TWO
3. HOLE B.
4. HOLE A.
5. INSERT HOLE A. HERE
6. HOLE B. GOES HERE
Image Notes
1. A CLOSE UP
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. THE STRAW IS BEHIND HERE.
2. STRAW IS BEHIND HERE AS WELL.
Image Notes
1. CUT OFF
2. IN HERE.
3. INSERT THIS...
4. ALREADY CUT
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. TAPE
2. TAPE
3. TAPE
4. TAPE
Image Notes
1. TAPE
2. TAPE
3. THESE 2 STRAWS ARE IN THE FRONT.
4. THESE STRAWS ARE IN THE BACK.
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. STRAW CUT-OFFS FROM BEFORE
Image Notes
1. 1 INCH
2. 1/4 OF AN INCH (OR 1 CM)
3. 1 INCH (OR 1 CM)
4. 1 CM
Image Notes
1. 1st. A STRAW...
2. 2nd. INSIDE A STRAW...
3. 3rd. INSIDE A STRAW...
Image Notes
1. PLACE TROUGH CENTER OF....
2. THE THREE STRAWS... (YOU COULD ALSO USE 2 SMALL BEADS)
3. AND THE PROPELLER.
4. THEN BEND THE LEFT OVER PAPER CLIP 90 DEGREES.
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. A PAPER CLIP.
2. PLACE SOME TAPE HERE.
3. PLACE TAPE HERE.
4. THE TAIL
Step 8: -THE ALL IMPORTANT RUBBER BANDThis is what makes the plane fly.
Look at pics.
Image Notes
1. "THE BOX"
Image Notes
1. "THE BOX"
2. THE TAIL
3. THE RUBBER BAND
Step 9: FINISHED!!!
Now all that needs to be done is to go outside and fly that brand new plane of yours!!! (Or stay in the house, just be very careful!)
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. If your plane still flies odd, even after you add the flaps, than it might be off-balanced.
2. #1. Put one point here, and another in the same spot on the opposite wing. These points will show you whether your plane is balanced or not. (The "points" I used
were two identical glue bottles. But you can use any two things that are the same height, and also have a single tip.)
3. #2. Put the other point here.
Image Notes
1. IF YOUR PLANE'S PROPELLER HITS IT'S WINGS, CUT THE WING A
LITTLE ON BOTH SIDES
2. KEEP THE HOLE INTACT
Image Notes
1. HERE WE SEE IT CUT AWAY PROPERLY.
2. LEAVE SOME PLATE BETWEEN THE HOLE AND WHERE YOU CUT AWAY
AT.
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Image Notes
1. IF YOUR PLANE FLYS FUNNY ADD SOME FLAPS TO HELP CORRECT
IT.
2. ONE HERE
3. HERE
4. HERE
5. HERE
6. AND HERE.
Image Notes
1. If your plane still flies odd, even after you add the flaps, than it might be offbalanced.
2. #1. Put one point here, and another in the same spot on the opposite wing.
These points will show you whether your plane is balanced or not. (The "points" I
used were two identical glue bottles. But you can use any two things that are the
same height, and also have a single tip.)
3. #2. Put the other point here.
4. #3. If the tail goes up, than add some weight to point "A" (but not a whole lot) If
the tail goes down, than add some weight to points "B" and "C" (again don't add to
much) (the weights I used were small washers, but you could use duck tape)
5. Point "A"
6. Point "B"
7. Point "C"
Related Instructables
rubberband
airplane by
thyssimon
Knex Paper
Airplane
Launchers by
Hitchtopher
Office Supplies
Airplane by Kurt
E. Clothier
AIRPLANE by
Thomas_V
How To Make A
Foam Glider
(Photos) by
macketymac
Paper Plane
Launcher by
Clukey98
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
Advertisements
Comments
27 comments Add Comment
njjack86 says:
kehinde1 says:
MegaMaker says:
Draxis says:
MegaMaker says:
walterh9 says:
I AGREE LOL
Draxis says:
lol
Dante9030 says:
Dante9030 says:
walterh9 says:
http://www.sciencetoymaker.org/plane/propeller.htm
here is a link to a site that teaches you how to make a propeller, i used this it turned out pretty good.
jid4611 says:
how long should the propeller be?
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/
jid4611 says:
jid4611 says:
dombeef says:
CAPS ARE FUN!!!!! Can you change that, it makes you sound like Billy Mays all the time
india94 says:
Mattrox says:
MegaMaker says:
watson9194 says:
Jupitane says:
Darn too bad.. i was gonna make a plane out of foam =(... mabye i will try hhhmmm?........
Draxis says:
meddler says:
Kiteman says:
dombeef says:
YEAH IT IS VERY ANNOYING IF YOU DO IT! (lol)
http://www.instructables.com/id/RUBBER-BAND-POWERED-FOAM-PLATE-AIRPLANE/