Documente Academic
Documente Profesional
Documente Cultură
3.3 in.
(159mm)
6.9 in.
(126mm)
6.2 in.
(174mm)
3.3 in.
(84mm)
Safety Technology6.3International
(Europe) Ltd.
in.
6.9 in.
(176mm)
.9 in.
Unit
49G Pipers Road (159mm)
Park Farm Industrial Estate Redditch
(23mm)
Worcestershire
B98 0HU 5.6
England
Tel: 44 (0) 1527 520 999
in.
91051 COVER
B 2.6 in.
FRAME TABS
3.3 in.
(207mm)
3.3 in.
6.9 in.
9105 FRAME
3.2 in.
(81mm)
(65mm)
8.2 in.
(174mm)
6.2 in.
(84mm)
(126mm)
(159mm)
.9 in.
(23mm)
6.3 in.
6.9 in.
(176mm)
(159mm)
5.6 in.
EXISTING FLUSH
MOUNT THERMOSTAT
(141mm)
VIEW A
91051 COVER
FRAME TABS
9105 FRAME
6.2 in.
(126mm)
(159mm)
EXISTING FLUSH
MOUNT THERMOSTAT
3.2 in.
(81mm)
3.3 in.
(84mm)
.9 in.
(23mm)
19013 SCREW
(4) PROVIDED
VIEW A
91051 COVER
FRAME TABS
19033 ANCHOR
(4) PROVIDED
9105 FRAME
CENTER FRAME OVER
EXISTING THERMOSTAT
EXISTING FLUSH
MARK AND DRILL (4) 1/4MOUNT
in.
THERMOSTAT
(6.3mm) HOLES AND COMPLETE
ASSEMBLY AS SHOWN.
9105 FRAME
19013 SCREW
(4) PROVIDED
A
STI-9105 (CLEAR)
STI-9105-S (SMOKE)
VIEW A
THE THREE (3)
KEYCOVER
(2) PROVIDED
TABS MUST FACE
PARTUPWARD.
OF COVER ASSEMBLY
SEE VIEW A ABOVE
INSTALLATION INSTRUCTIONS
9105 FRAME
CENTERPrior
FRAMEto
OVER
1. Do not remove thermostat.
drilling anchor holes,
19013cover
SCREW thermostat
EXISTING THERMOSTAT
91051
COVER AND
with a damp cloth
to
prevent
dust
from
penetrating
the
sensor.
(4)
PROVIDED
MARK AND DRILL (4) 1/4 in.
LOCK ASSEMBLY
2. Center frame over
existing
(6.3mm)
HOLES thermostat.
AND COMPLETE Mark and drill (4) anchor holes using
AS SHOWN.
a 1/4 in. (6.3mm) drillASSEMBLY
bit. Insert
the (4) anchors and complete installation
STI-9105 (CLEAR)
as shown.
STI-9105-S (SMOKE)
NOTE: The (3) tabs on the frame must face upward (View
A).
3. Insert the (3) slots on the cover over tabs on the top surface of frame.
Rotate cover downward onto the frame and turn key to lock.
9105 FRAME
CENTER FRAME OVER
EXISTING THERMOSTAT
MARK AND DRILL (4) 1/4 in.
(6.3mm) HOLES AND COMPLETE
ASSEMBLY AS SHOWN.
INSTALLATIONS
19033 ANCHOR
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
CLEANING INSTRUCTIONS
To clean cover, remove from wall. Rinse with water to remove abrasive dust and
dirt. Wash with soap or mild detergent using a soft cloth (DO NOT SCRUB). Rinse
once more, then dry with a soft cloth or chamois. To remove grease or wet paint,
rub gently with a cloth wetted thoroughly with naphtha. Then wash and rinse. DO
NOT USE RAZOR BLADES.KEY (2) PROVIDED
PART OF COVER ASSEMBLY
All specifications and information shown were current as of publication and are subject to change without notice.
91051 COVER AND
LOCK ASSEMBLY
9105IS NOV2005