. Bind the Iinks between DLS1 and ALS1 in an EtherChanneI and configure the two switches to activeIy negotiate a PAgP Iink.
Make sure that you have a trunk link active for those two links ALS1# show interfaces trunk LS1(config)# interface range fastEthernet 0/7 - 8 LS1(config-if-range)# channel-group 1 mode desirable LS1(config-if-range)#exit LS1(config)# interface port-channel 1 LS1(config-if)# switchport mode trunk LS1# show etherchanneI summary ALS1# show interfaces trunk
LS1# show interfaces trunk DLS1(config)# interface range fastEthernet 0/7 - 8 DLS1(config-if-range)# channel-group 1 mode desirable DLS1(config)# interface port-channel 1 DLS1(config-if)# switchport mode trunk LS1# show etherchanneI summary LS1# show interfaces trunk
f the EtherChannel does not come up, you might want to try "flapping the physical interfaces on both ends of the EtherChannel. This involves using the shut command on those interfaces, followed by a no shut command a few seconds later.
6. PIace aII switches in the VTP domain CISCO with DLS1 as the VTP server using VTP version 2. Configure aII other switches as VTP cIients.
uLS1# vtp tatu uLS1(confla)# vtp da|n CI5CC uLS1(confla)# vtp ver|n 2 uLS1(confla)# vtp de erver
. On DLS1, create VLAN 10 named CLIENT, VLAN 20 named VOICE, VLAN 30 named SERVER and VLAN 99 named MGMT. Choose a 192.168.X.0/24 network for each VLAN for use in subsequent steps
9. Configure the Rapid PVST (PVRST+) protocoI on aII switches. Ensure that DLS1 becomes the spanning tree root of VLANs 10 and 20 and DLS2 becomes the backup. Ensure that DLS2 becomes the spanning tree root of VLANs 30 and 99 and DLS1 becomes the backup.
10. On DLS1 and DLS2 configure SVIs and HSRP to provide gateway redundancy for access Iayer cIients in VLANs 10, 20, 30 and 99. Create an SVI in VLANs 10, 20, 30 and 99, each with an IP address and mask from their respective networks chosen in Step 6. 11. Configure DLS1 as the active HSRP router for VLANs 10 and 20 and configure DLS2 as backup. Configure DLS2 as the active router for VLANs 30 and 99 and configure DLS1 as backup.
S1(config)#interface vlan 10 S1(config-if)#ip add 192.168.10.3 255.255.255.0 S1(config-if)#no sh
S1(config)#interface vlan 20 S1(config-if)#ip add 192.168.20.3 255.255.255.0 S1(config-if)#no sh
S1(config)#interface vlan 30 S1(config-if)#ip add 192.168.30.3 255.255.255.0 S1(config-if)#no sh
S1(config)#interface vlan 99 S1(config-if)#ip add 192.168.99.3 255.255.255.0 S1(config-if)#no sh
S2(config)#interface vlan 10 S2(config-if)#ip add 192.168.10.4 255.255.255.0 S2(config-if)#no sh
S2(config)#interface vlan 20 S2(config-if)#ip add 192.168.20.4 255.255.255.0 S2(config-if)#no sh
S2(config)#interface vlan 30 S2(config-if)#ip add 192.168.30.4 255.255.255.0 S2(config-if)#no sh
S2(config)#interface vlan 99 S2(config-if)#ip add 192.168.99.4 255.255.255.0 S2(config-if)#no sh
12. On ALS1 and ALS2 create an SVI for MGMT VLAN 99 with an IP address from the VLAN 99 network assigned in Step 6. ALS1(config)#interface vlan 99 ALS1(config-if)#ip add 192.168.99.5 255.255.255.0 ALS1(config-if)#no sh ALS2(config)#interface vlan 99 ALS2(config-if)#ip add 192.168.99.6 255.255.255.0 ALS2(config-if)#no sh
13. For ALS1 and ALS2, specify the HSRP gateway address of VLAN 99 as the defauIt gateway. LS1(config)# ip default-gateway 192.168.99.1 LS2(config)# ip default-gateway 192.168.99.1
14. EnabIe PortFast on aII access Iayer switch ports.
1. Permit the Iinks between DLS2 and ALS2 to carry traffic onIy for the VLANs created in Step 6. ALS2(config)# (config)#interface range fastEthernet 0/7 - 8 ALS2(config-if)#switchport trunk allowed vlan 10,20,30,99 LS2(config)# (config)#interface range fastEthernet 0/7 - 8 LS2(config-if)#switchport trunk allowed vlan 10,20,30,99
ALS1# show mIs qos interface fastEthernet 0/6 ALS1# show run interface fastEthernet 0/6
18. On ALS1, configure port Fa0/6 with port security. Allow up to two MAC addresses to be learned for P phone support. Enable sticky learning. Shut down the port if a violation occurs.
20. Configure P routing on LS1 and LS2, and use EGRP to advertise 192.168.0.0/16 with automatic summarization disabled. LS1(config)#ip routing LS1(config)#router eigrp 1 LS1(config-router)#no auto-summary LS1(config-router)#network 192.168.0.0