Documente Academic
Documente Profesional
Documente Cultură
xmcd(R)
Project = "10' x 6' under 3' fill" DesignedBy = "Design Example" CheckedBy = "Design Example"
b w = 1 ft This program analyzes a one foot wide cross section
Note: AASHTO section references are shown at right margin, where appropriate, in bold-italic font
Design Parameters
Geometry and Box Dimensions Tb = 12 in Extension = 0 bottom slab thickness, (8 inch min.) extension type 0 new box no exten. 1 left extension 2 right extension
Skewbox =
0 deg 0
Environmental Class 1-slightly aggresive 2-moderate 3-extreme concrete strength lbf ft
3
density of concrete
iwbeg := if [ ( Extension 2 ) , 0 , 1 ] iwend := if [ ( Extension 1 ) , 1 , 0 ] iw := iwbeg .. iwend index for number of cutoff walls
02/10/2011
4CutoffwallHeadwall.xmcd v3.2
0 deg 0
index for number of cutoff walls iwbeg := if ( Extension 2 , 0 , 1 ) iwend := if ( Extension 1 , 1 , 0 ) iw := iwbeg .. iwend iw =
0 1
Enter Cutoff Wall Dimensions Note: changes in height or width of the Cutoff Wall or Headwall requires a recalculation of the Loads file (2Box&HeadwallLoads.mcd). Height of Cutoff Wall includes the thickness of the bottom slab. Cutoff walls exceeding 2 feet below the bottom slab is beyond the intent of this program. Values currently being used by the program Change Group values (gray) or change individual values (white) newBcw.left := XX in Cutoff wall width & height Bcw =
12 in 12
Hcw =
24 in 24
newBcw := XX in newHcw := XX in
newBcw.right := XX in newHcw.left := XX in newHcw.right := XX in BarSizeD8 := XX NumD8 := XX NumD8 := XX NumD8 := XX NumD8 := XX SD8 := XX SD8 := XX := XX := XX := XX
Note: Height of Cutoff Wall includes the thickness of the bottom slab Enter Cutoff Wall Reinforcing
07 08 10 11 09 12
07 08 10 11
left Cutoff wall, top 4 left Cutoff wall, bot 4 right Cutoff wall, top BarSizecw = 4 right Cutoff wall, bot
2 2 Numcw = 2 2 15 in 15
newBarSizecw := XX newNumcw := XX
StirSizecw =
3 3
Sstirrup.cw =
newStirSizecw := XX newSstirrup.cw := XX in
BarSizeD8 BarSizeD8
09 12
:= XX in := XX in
02/10/2011
4CutoffwallHeadwall.xmcd v3.2
checkCrackingmidspan.cw = checkCrackingsupport.cw =
CheckCrackingmidspan.cw = CheckCrackingsupport.cw =
Moment, minimum steel, and spacing checks CheckMmidspan.cw = CheckMsupport.cw = CheckAsmin.top.cw = CheckAsmin.bot.cw =
CheckS stirrup.cw =
"ok" "ok"
Skewbox =
0 deg 0
BarrierDLhw = 0
kip ft
Additional dead load if a barrier is located on top of the headwall This variable sets whether a line of truck wheels is considered as a loading. A 1 value means it is considered and a 0 means it is not
ConsiderLLhw = 1
Note: Height of Headwall includes the thickness of the top slab Enter Headwall Dimensions Values currently being used by the program Headwall height Hhw =
24 in 24 14 in 14
Bhw =
02/10/2011
4CutoffwallHeadwall.xmcd v3.2
BarSizeD8 left Headwall, top 6 left Headwall, bot 6 right Headwall, top BarSizehw = 6 right Headwall, bot
01 02 04 05 03 06
01 02 04 05
:= XX := XX := XX := XX
2 3 Numhw = 2 3
newBarSizehw := XX newNumhw := XX
3 StirSizehw = 3
12 in Sstirrup.hw = 12
newStirSizehw := XX newSstirrup.hw := XX in
BarSizeD8 BarSizeD8
03 06
:= XX in := XX in
Section 5 - Headwall Design, 8 pages Shear generally controls wall size CheckV ext.support.hw = CheckV int.support.hw = cracking generally controls reinforcement area
CheckCrackingmidspan.hw = CheckCrackingsupport.hw =
CheckAsmin.bot.hw = CheckAsmin.top.hw =
CheckS stirrup.hw =
"ok" "ok"
Assign the data values read in to the ones to be read out, then change only the ones modified in this file DataOut := Bcw in DataOut := := Hcw in Sstirrup.cw in DataOut := BarSizecw := Bhw in
41
42
43
44
DataOut DataOut
45 50
DataOut
46
DataOut
48
DataOut
51
DataOut DataOut
52 57
DataOut
53
DataOut := ReinfCW
56
92
02/10/2011
4CutoffwallHeadwall.xmcd v3.2