Documente Academic
Documente Profesional
Documente Cultură
1 (13)
2 (13)
MGW
ZJVI; --- All the VMGWs should be in registered condition -----------------------------------------------------------------------------------------------------------------------------------
Fallback
Fallback in (HDD) in MSS/MGW
ZWQO:CR; ----- To see created software package. ZWQO:RUN; -----To see running package. One package should be in BU condition . ZWQD:NAME=<PACKAGE NAME>:DIRE,::; ---------To delete old software package ZWKS:MODE=FULL,NAME=FB160309,DIRE=FB160309::; --- To start fallback in HDD ZWKI::; ---------- To see fallback progress
Unit Checking
ZUSI; ---- To see unit state in MSS and MGW ZUSI:COMP; --------- To see all computer units in MSS ZUSI:<UNIT NAME>; ----- To see specific unit state in MSS and MGW
ZUDH:SIGU,5:::; --- To see the diagonesis history If DGN result of unit not showing OK
3 (13)
Check the Physical location of unit: ZWTI :P:SIGU,6:; Replace the working UNIT: ZUSC:SIGU,6;TE ZUSC:SIGU,6:SE(SE-OU) ZUSC:SIGU,6:SE(SE-NH) Now replace the Unit again do the 3(ZUDU,ZUDQ,ZUDH) Command. If ok. ZUSC:SIGU,5:SP/WO
4 (13)
ZNEL; --- To see all signaling links ZNEL:: STATE=UA; --- To see unavailable signaling links ZOLT; ---- To see link load ZNCC:LINK NO:PCM-TSL,BIT RATE,NO OF TSL,1:UNIT,INDEX:0:; --- To create a signaling link For example if we give the below mention command link number 1 will be created with bitrate 64 Kbps and PCM no-124 and TSL-16 in CCSU unit 2. ZNCC: 1:124-16, 64, 1, 1: CCSU, 2:0:; ZNEL: 1; --- To see signaling link ZNSC:NA1,D'1234,TEST:1,0:; ---- To create link SET ZNSI:NA1,D'1234:; --- To see link set data ZNSA:NA1,D'1234,TEST:2,1:; --- To add link to a link set -------------------------------------------------------------------------------------------------------------------------------------------
Clock SYNCHRONIZATION
ZDRI; ----------- To see external clock synchronization STATE should be connected in MSS ZUSI:CLS; --- To see internal clock one should bw WO-EX and another should be in SP-EX in MSS ZUSI:TBU; -- To see internal clock one should bw WO-EX and another should be in SP-EX in MGW ZDYI; -- To see external clock synchronization STATE should be connected in MGW ZDCD; --- To see the real time of MSS/MGW ----------------------------------------------------------------------------------------------------------------------------------------
5 (13)
RESULT ANALYSIS SS7 GTI TT NP NAI DIGITS RECORD TYPE ---- --- --- --- --- ------------------------ ------ -------ITU 4 0 1 4 9197169 6 BASIC
ZNAI:RES=6; ---- To see the SPC for Result Record To create Result Record we have to create Signalling Route with MML Command as below:ZNRC:NA1,D'1234,TEST,0,A,N:NA1,D'1234,TEST,7::::; ZNRI: NA1, D1234:; --- To see route set data ZNVA:NA1,D'1234:NA1,D'1234:; ZNVC:NA1,D'1234:NA1,D'1234:ACT; Then we have to define SCCP with following command:ZNFD:NA1,D'1234,0:6,MAPH,0,:7,MAPV,0,:8,MAPM,0,:92,CAP,0,::; ZNHI: NA1, D1234; --- To see SCCP data ZNHI: NA1, D1234; --- To see SCCP data ZNGC:NA1,D'1234:ACT; ZNHC:NA1,D'1234:6:ACT;
6 (13)
ZNHC:NA1,D'1234:7:ACT; ZNHC:NA1,D'1234:8:ACT; ZNHC:NA1,D'1234:92:ACT; Then use following command to create Result Record ZNAC:NET=NA0,DPC=D'1234,RI=GT,:::; --- To create Result Record ZNAI:RES=<RESULT RECORD NUMBER>; ---- To see the output For example ZNAI:RES=6; INQUIRING GLOBAL TITLE TRANSLATION RESULT RESULT LS SP ENTITY LS RECORD STA IND NET SP CODE H/D NAME RI STATE PR WGHT ------ --- --- --- ------------------ ----- --- ------ -- ---00006 ACT NO NA1 13C4/05060 HLR01 SSN AV-EX - For example RES 6 is routed to SPC- 5060(HLR01). Then we will check with the following command ZNRI:NA1,D5060; INTERROGATING SIGNALLING POINT DATA NET SP CODE H/D NAME RS STATE PAR SET --- ------------------ ----- -------- ------NA1 13C4/05060 HLR01 AV 6 LOAD SHARING BETWEEN SIGNALLING ROUTES ALLOWED ROUTES: SP CODE H/D NAME STATE PRIO ------------------ ----- ------ ---13C4/05060 HLR01 AV-EX 7
CGR Commands
ZRCI; --- To see all the CGRs in MSS/MGW ZCEL:CGR=404; --- To see calls in a CGR in MSS ZCII:CGR=555; --- To see calls in a CGR in MGW
7 (13)
ZRCI:SEA=3:CGR=404:PRINT=2; ---- To see Circuit Group parameters ZRCI:SEA=3:CGR=404:PRINT=5; ZRCI:SEA=3:CGR=404:PRINT=4; --- To see all CGR parameters --- To see all circuits in CGR
If you want to know a PCM is connected to which CGR then give the below mentioned command:ZRCI:SEA=4:CRCT=264-1&&-31; -- Where 264 is the PCM number To change the state of the circuits in a CGR first give the below mentioned command ZRCI:SEA=3:CGR=404:PRINT=4; Kindly note down the PCM numbers and then the below command ZRCI:SEA=3:CGR=404:PRINT=2;
MAIN LEVEL COMMAND <___> < RCI:SEA=3:CGR=404:PRINT=2; LOADING PROGRAM VERSION 12.52-0 CIRCUIT GROUP(S) CGR : 404 NCGR : BSCVIK1E
TYPE : ECCS STATE : WO-EX HUNTED : YES FORMAT : TERMID HM1 : LF HM2 : LF NBCRCT : 1392 TREE : DIR : OUT LSI : AIF02 INR :NCCP : METHOD : NET : NA1 SPC(H/D) : 1C8B/07307 ASI :UPART : BSSAP MGW : MSS01MGW0103 FQDN :-
AUTOMATIC CONGESTION CONTROL REJ11 : REJ12 : REJ21 : REJ22 : ACT11 : NO ACTION ACT12 : NO ACTION ACT21 : NO ACTION ACT22 : NO ACTION SELECTIVE CIRCUIT RESERVATION TRES1 : DR1A : DR1B : DR1C : TRES2 : DR2A : DR2B : DR2C : ART1A : ART1B : ART1C : ART2A : ART2B : ART2C : ACTA : NO ACTION ACTB : NO ACTION ACTC : NO ACTION
COMMAND EXECUTED
Then copy the VMGW name (MSS01MGW0103) and then give the below command in MSS only
8 (13)
ZCEC:MGW=MSS01MGW0103,TERMID=10274-1&&-31,:BA; --- To bar the circuits where 10274 is the PCM number ZCEC:MGW=MSS01MGW0103,TERMID=10274-1&&-31,:NU; --- To not use the circuits in MSS ZCIM:CRCT=1234-1&&-31:WO; -- To change the state of the circuit in MGW ZRCC:TYPE=ECCS,CGR=329,NCGR=BSC34SUR:DIR=OUT,NET=NA1,SPC=D'7034,LSI=AIF02, UPART=5:MGW=ASMGW202:; --- To create CGR 329, with Name- BSC34SUR, SPC-7034, and VMGW- ASMGW202 ZRCC:TYPE=SPE,CGR=329,NCGR= BSC34SUR:USE=VMGW:; -- To create CGR in MGW ZCRM:CGR=329:WO; ---- To change the STATE of the CGR in MSS ZCIM:CGR=329:WO; ---- To change the STATE of the CGR in MGW ZRRC:EXT:ROU=329,OUTR=OMCG0,NCCP=MAS,STP=1,TON=UNK,NCGR=BSC34SUR; create Traffic ROUTE in MSS only --- To
ZRCA:CGR=404:TERMID=10234-1&&-31,:CCSPCM=0::UNIT=BSU,INDEX=8:; --- To add circuits in a CGR in MSS only ZRCA:CGR=329:CRCT=1234-1&&-31; To add circuits in a CGR in MGW only -------------------------------------------------------------------------------------------------------------------------------------------
NUMBER MODIFICATION RULES: START POINT OF REMOVED DIGITS : 1 NUMBER OF DIGITS REMOVED : 5 START POINT OF ADDED DIGITS : 1 ADDED DIGITS : 55031
ZCFD:TYPE=IMSI:DIG=72431;
From the IMSI analysis o/p check the GT analysis properly with command ZNBI:::55031;
9 (13)
USERNAME USER USER MML SESSION SYSTEM I/O-DEVICE NUMBER SYSTEM 220366 MSS01_GGN OMU-VTP20 RI 01244 SYSOP1 220366 MSS01_GGN OMU-VTP15 QN 01237
220366 MSS01_GGN
COMMAND EXECUTED
From above o/p the logged VTP would be VTP-15 , because in its right side it is showing QN command which you fired last. Then give the command LOGICAL FILE MODIFIED: SYSTEM = MSS01_GGN UNIT = OMU PAGE 1 LOG LOG SPARE PHYSICAL OBJ SYSTEM FILE FILE FILE FILE IND NAME NAME NBR NAME & CLASS MODE NAME 93 GSMME1PR P /TRACE/ GSMME1PR.TXT,0 (** RING FILE **) COMMAND EXECUTED UNIT DEVICE/ LOGICAL FILE WDU-SB VTP-23 VTP-15
ZIIS::GSMME1PR::DEV=VTP-15;
Please note! In device list WDU-SB should be always connected to OMU. At a time max 4 devices can be connected one is WDU-SB of OMU and three are different VTP or LPT. If you find that 4 devices are already connected and you want to connect another device then you have to give the followind command:ZIIS::GSMME1PR:IND=3:DEV=VTP-15; In this case IND=3 position VTP would be disconnected and new VTP would be added.
10 (13)
You can also give IND=2 or IND=4 according to the situation. Please do not disconnect the WDU-SB from OMU. We can also take trace using the below mentioned command at the time of call test ZMCJ:IMSI=<IMSI NUMBER>::TYPE=D;
DIAGNOSTIC in MSS/MGW
To do diagonesis of an unit it should be in test mode. For example if we want to diagonose a ET no 258 then we have to change its working state with to TE with command as below:ZUSC:ET,258:BL; ---- To block the ET ZUSC:ET,258:TE; --- To change in to test mode ZUDU:ET,258:::; ---- To start the daigonesis of the ET ZUDQ; ---- To see current diagonesis test
WORKING STATE OF UNITS UNIT PHYS STATE LOCATION OMU-0 0000 WO-EX OMU-1 0001 SP-EX TOTAL OF 2 UNITS
COMMAND EXECUTED
Now if we want to change the state of OMU to WO-EX from SP-EX then we have to give the following command:ZUSC:OMU,0:SP,:; --- To switchover the OMU 1 from SP-EX to Wo-EX. After the command execution the O/P will be as follows:WORKING STATE OF UNITS UNIT PHYS STATE LOCATION OMU-0 0000 SP-EX OMU-1 0001 WO-EX TOTAL OF 2 UNITS INFO
11 (13)
COMMAND EXECUTED
DOCUMENTTYPE TypeUnitOrDepartmentHere TypeYourNameHere ZMIM:IMSI=<IMSI NUMBER>:CAT=TP; Now make the desired circuits in TE-ID mode with command ZCEC:MGW=MSS01MGW0103,TERMID=10274-1&&-31,:TE; Now do test call and check the circuit with command ZMCJ:IMSI=<IMSI NUMBER>; TypeDateHere
12 (13)
13 (13)
If we create a new CGR then we have to add the CGR in object lis for measurement The commands are as follows:ZTGC:CGR,1:CGR=400:; ---- CGR 400 would be added in object list 1