Documente Academic
Documente Profesional
Documente Cultură
Flexible
Couplings
Lowest Cost
T O TA L S o l u t i o n
FC
SECTION
F1
SURE-FLEX
ELASTOMERIC
COUPLINGS
F11
SURE-FLEX CAPABILITIES
4-WAY FLEXING ACTION
absorbs all types of
shock, vibration and misalignment
TORSIONAL
Sure-Flex coupling sleeves have an exceptional ability to
absorb torsional shock and dampen torsional vibrations.
The EPDM and Neoprene sleeves wind-up approximately 15 torsionally at their rated torque. Hytrel
sleeves will wind-up about 7.
ANGULAR
The unique design of the Sure-Flex couplings teeth
allows for the absorption of angular misalignment without
wear. Refer to page F118 for actual allowable
misalignment limits. These limits allow for the alignment
of the coupling using only a scale and calipers.
PARALLEL
Parallel misalignment is absorbed without wear or
appreciable energy losses. The lateral flexibility of the
coupling sleeve minimizes radial bearing loads normally
associated with parallel misalignment. This feature also
allows for easier installation by the use of components
bored for slip fits without fretting corrosion occurring at
the shaft. Refer to page F118 for parallel misalignment
limits. Only a straight-edge and feeler gage are required
to obtain these limits.
AXIAL
Sure-Flex couplings may be used in applications with
limited axial shaft movements. The axial compressibility
of the EPDM and Neoprene sleeves allows for shaft endfloat without the absolute transfer of thrust loads.
F12
SURE-FLEX FEATURES
EASY, QUICK
INSTALLATION
NO LUBRICATION,
TROUBLE-FREE OPERATION
SURE-FLEX SELECTION
Sure-Flex couplings are selected as component parts.
1.
2.
3.
PROD. NUMBER
PROD. DESCRIPTION
6S138
6S1
6J
6Sx1-3/8
6Sx1
6JE
9SC5011
9SC50
11SCH238
9SCHS118
9H
9SC50-11
9SC50
11SCH x 2-3/8
9SCHS x 1-1/8
9H
F13
Sure-Flex Sleeves are available in four materials or compounds and various shape configurations.
EPDM
Neoprene
Hytrel
Urethane
JE
JES
E
JN
JNS
N
HS
General
Purpose
Oil Resist
Non-flame
General
Purpose
Stiffness
REL. RATING
WIND-UP ANGULAR
MISALIGN
1X
15
1
1X
15
1
4X
7
1/4
4X
3
1/4
TEMPERATURE (F)
maximum
minimum
+275
30
+200
0
+250
65
+200
80
CONSTRUCTIONS
AVAILABLE
1 pc, unsplit
1 pc, split
2 piece
TYPICAL USE
SURE-FLEX SLEEVES
Product
No.
Product
Description
Product
No.
Product
Description
Product
No.
3J
4J
5J
6J
7J
8J
9J
10J
3JE EPDM
4JE EPDM
5JE EPDM
6JE EPDM
7JE EPDM
8JE EPDM
9JE EPDM
10JE EPDM
4
5
6
7
8
9
10
11
12
13
14
16
4E EPDM
5E EPDM
6E EPDM
7E EPDM
8E EPDM
9E EPDM
10E EPDM
11E EPDM
12E EPDM
13E EPDM
14E EPDM
16E EPDM
6H
7H
8H
9H
10H
11H
12H
F14
3JS
4JS
5JS
6JS
7JS
8JS
9JS
10JS
3JN
4JN
5JN
6JN
7JN
8JN
3JN
4JN
5JN
6JN
7JN
8JN
3JNS
4JNS
5JNS
6JNS
7JNS
8JNS
3JNS
4JNS
5JNS
6JNS
7JNS
8JNS
Neoprene
Neoprene
Neoprene
Neoprene
Neoprene
Neoprene
Neoprene
Neoprene
Neoprene
Neoprene
Neoprene
Neoprene
Split
Split
Split
Split
Split
Split
4N
5N
6N
7N
8N
9N
10N
11N
12N
13N
14N
4N Neoprene
5N Neoprene
6N Neoprene
7N Neoprene
8N Neoprene
9N Neoprene
10N Neoprene
11N Neoprene
12N Neoprene
13N Neoprene
14N Neoprene
6HS
7HS
8HS
9HS
10HS
11HS
12HS
13HS
14HS
10U
11U
12U
Product
Description
6H Hytrel
7H Hytrel
8H Hytrel
9H Hytrel
10H Hytrel
11H Hytrel
12H Hytrel
6HS Split Hytrel
7HS Split Hytrel
8HS Split Hytrel
9HS Split Hytrel
10HS Split Hytrel
11HS Split Hytrel
12HS Split Hytrel
13HS Split Hytrel
14HS Split Hytrel
10U Urethane
11U Urethane
12U Urethane
JE, JN
E-N
These sleeves are of two-piece design
with a retaining ring. They are available
in either EPDM (E) or Neoprene (N).
They may be used with any flange
within a given size. Sleeves are shown
here assembled and disassembled.
E and N
(Assembled)
Types E and N
(Disassembled)
H-HS-U
H (Hytrel) and U (Urethane) sleeves,
designed for high-torque applications,
transmit four times as much power as an
equivalent EPDM or Neoprene sleeve.
Available in one-piece solid construction
(H or U) or two-piece split construction
(HS), these can be used only with S, C
and SC flanges. They cannot be used with
J or B flanges or as direct replacements
for EPDM or Neoprene sleeves.
HS
H or U
DIMENSIONS (in.)
Coupling
Size
3
4
5
6
7
8
9*
10*
11
12
13
14
16
1
1 1/4
1 9/16
1 7/8
2 3/16
2 1/2
3
3 7/16
...
...
...
...
...
.06
.10
.20
.40
.62
1.13
1.46
2.32
...
...
...
...
...
E and N Sleeves
EPDM & Neoprene
H, U & HS Sleeves
Hytrel & Urethane
Wt.
(lbs.)
Wt.
(lbs.)
...
2 5/16
2 15/16
3 3/4
4 11/32
5 1/16
6
7 1/16
8 3/16
9 9/16
11 3/16
13 3/32
17 29/32
...
1 1/4
1 9/16
1 7/8
2 3/16
2 1/2
3
3 7/16
4
4 11/16
5 1/2
6 1/2
8 3/4
...
.11
.25
.49
.77
1.4
2.0
3.2
5.1
8.1
13.0
21.1
45.3
...
...
...
3 3/4
4 11/32
5 1/16
6
7 1/16
8 3/16
9 9/16
11 3/16
13 3/32
...
...
...
...
1 7/8
2 3/16
2 1/2
3
3 7/16
4
4 11/16
5 1/2
6 1/2
...
...
...
...
.44
.69
1.4
1.8
2.9
4.5
7.3
11.8
19.3
...
F15
Load Symbol
Application
Load Symbol
Application
Load Symbol
MILLS
Ball, Pebble, Rod, Tube, Rubber Tumbling. H
Dryer and Cooler. . . . . . . . . . . . . . . . . . . . M
MIXERS
Concrete, Muller . . . . . . . . . . . . . . . . . . . . M
Banbury . . . . . . . . . . . . . . . . . . . . . . . . . . H
ORE CRUSHER . . . . . . . . . . . . . . . . . . . . . . H
OVEN CONVEYOR . . . . . . . . . . . . . . . . . . . . L
PLANER (metal or wood) . . . . . . . . . . . . . . . M
PRESSES
Brick, Briquette Machine . . . . . . . . . . . . . . H
Notching, Paper, Punch, Printing . . . . . . . . M
PUG MILL. . . . . . . . . . . . . . . . . . . . . . . . . . . M
PULP GRINDER (paper) . . . . . . . . . . . . . . . . H
PULVERIZERS
Hammermilllight duty, Roller. . . . . . . . . . M
Hammermillheavy duty, Hog. . . . . . . . . . H
PUMPS
Centrifugal, Axial . . . . . . . . . . . . . . . . . . . . L
Gear, Lobe, Vane . . . . . . . . . . . . . . . . . . . M
Reciprocatingsgl. or dbl. acting,
cylinder . . . . . . . . . . . . . . . . . . . . . . . . . *
REEL, REWINDER (paper) CABLE. . . . . . . . M
ROD MILL. . . . . . . . . . . . . . . . . . . . . . . . . . . H
SAWDUST CONVEYOR . . . . . . . . . . . . . . . . L
SCREENS
Air Washing, Water . . . . . . . . . . . . . . . . . . L
Rotary for coal or sand . . . . . . . . . . . . . . . M
Vibrating . . . . . . . . . . . . . . . . . . . . . . . . . . H
SCREW CONVEYOR . . . . . . . . . . . . . . . . . . L
SLAB CONVEYOR (lumber) . . . . . . . . . . . . . M
SLITTERS (metal). . . . . . . . . . . . . . . . . . . . . M
SOAPERS (textile). . . . . . . . . . . . . . . . . . . . . L
SORTING TABLE (lumber) . . . . . . . . . . . . . . M
SPINNER (textile) . . . . . . . . . . . . . . . . . . . . . M
STOKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . L
SUCTION ROLL (paper) . . . . . . . . . . . . . . . . M
TENTER FRAMES (textile) . . . . . . . . . . . . . . M
TIRE BUILDING MACHINES. . . . . . . . . . . . . H
TIRE & TUBE PRESS OPENER . . . . . . . . . . L
TUMBLING BARRELS . . . . . . . . . . . . . . . . . H
WASHER and THICKENER (paper) . . . . . . . M
WINCHES . . . . . . . . . . . . . . . . . . . . . . . . . . M
WINDERS, Paper, Textile, Wire. . . . . . . . . . . M
WINDLASS. . . . . . . . . . . . . . . . . . . . . . . . . . M
WIRE
Drawing. . . . . . . . . . . . . . . . . . . . . . . . . . . H
Winding . . . . . . . . . . . . . . . . . . . . . . . . . . M
WOODWORKING MACHINERY . . . . . . . . . . L
L
Light
M
Medium
H
Heavy
Standard AC Motor
DC Shunt Motor
*Engine, 8 or more cylinders
1.25
1.5
2.0
1.5
2.0
2.5
2.0
2.5
3.0
Turbine
1.0
1.25
1.5
*On applications involving varying torque loads, design around the maximum load. Then determine the resulting
service factor at minimum load. If this value is greater than 4.0, special coupling alignment will be required (see
page F118).
Caution: Applications involving reciprocating engines and reciprocating driven devices are
subject to rotational vibrational critical speeds which may destroy the coupling. The factory can
determine these speeds when the rotational inertia (WR2) of the driveR and driveN units is
known.
F16
COUPLING RATINGS
Size
EPDM
Sleeves
Neoprene
Sleeves
3
4
5
6
7
8
9
10
11
12
13
14
16
JE,JES
E,JE,JES
E,JE,JES
E,JE,JES
E,JE,JES
E,JE,JES
E,JE,JES
E,JE,JES
E
E
E
E
E
JN,JNS
N,JN,JNS
N,JN,JNS
N,JN,JNS
N,JN,JNS
N,JN,JNS
N
N
N
N
N
N
Size
Hytrel
Sleeves
Urethane
Sleeves
6
7
8
9
10
11
12
13
14
H, HS
H, HS
H, HS
H, HS
H, HS
H, HS
H, HS
HS
HS
U
U
U
HP @ RPM
100
0.1
0.2
0.4
0.7
1.2
1.8
2.9
4.6
7.2
11.4
18.0
28.6
75.0
1160
1750
3500
1.1
2.2
4.4
8.3
13
20
33
53
83
132
209
331
870
1.7
3.3
6.7
12.5
20
32
50
80
126
200
315
500
3.3
6.7
13
25
40
63
100
160
252
HP @ RPM
100
2.9
4.6
7.2
11.4
18.0
28.6
50.0
75.0
115.0
1160
33
53
84
132
209
331
580
870
1334
1750
50
80
126
200
315
500
875
1312
2013
3500
100
160
252
400
630
1000
Torque
(in. lbs.)
60
120
240
450
725
1135
1800
2875
4530
7200
11350
18000
47250
Torque
(in. lbs.)
1800
2875
4530
7200
11350
18000
31500
47268
72480
Stiffness
(in. lbs./rad)
229
458
916
1718
2769
4335
6875
10980
17300
27500
43350
68755
180480
Stiffness
(in. lbs./rad)
10000
20000
30000
47500
100000*
125000*
225000*
368900
593250
Max
RPM
9200
7600
7600
6000
5250
4500
3750
3600
3600
2800
2400
2200
1500
Max
RPM
6000
5250
4500
3750
3600
3600
2800
2400
2200
F17
1
11/2
2
3
3
4
4
5
3
4
4
5
5
3
4
4
5
5
4
4
5
5
6
4
5
5
6
6
3
5
7 1/2
10
15
5
6
7
7
8
6
6
7
8
9
6
7
8
8
9
6
7
8
9
10
20
25
30
40
50
9
9
10
10
11
9
10
10
11
11
10
10
11
11
12
60
75
100
125
150
11
12
12
13
13
12
12
13
13
14
200
250
300
350
400
14
14
16
16
16
450
500
600
700
800
3/4
1
11/2
2
3
3
3
4
4
3
3
4
4
5
3
4
4
5
5
3
4
4
5
5
4
4
5
5
6
7
8
9
9
10
3
5
7 1/2
10
15
5
6
6
7
8
5
6
7
7
8
6
6
7
8
9
6
7
8
8
9
10
11
11
12
12
11
11
12
12
13
20
25
30
40
50
8
9
9
10
10
9
9
10
10
11
9
10
10
11
11
12
13
13
14
14
13
13
14
14
16
13 60
14 75
14 100
. . . 125
16 150
11
11
12
12
13
11
12
12
13
13
14
16
16
16
16
16
16
16
16
16
16 16
16 16
16 . . .
... ...
... ...
200
250
300
350
400
13
14
14
16
16
16 16
16 16
16 . . .
... ...
... ...
...
...
...
...
...
...
...
...
...
...
450
500
600
700
800
...
...
...
...
...
3/4
1
11/2
2
3
3
3
3
4
3
3
3
4
4
3
3
3
4
4
3
3
4
4
5
3
4
4
5
5
1
11/2
2
6
7
8
9
10
3
5
7 1/2
10
15
4
5
6
6
7
5
5
6
6
7
5
6
6
7
8
5
6
7
7
8
6
6
7
8
9
3
5
7 1/2
10
15
3
4
5
5
6
4
4
5
5
6
4
5
5
6
6
4
5
6
6
7
5
5
6
6
7
10
10
11
11
12
10
11
11
12
12
20
25
30
40
50
7
8
8
9
9
8
8
9
9
10
8
9
9
10
10
9
9
10
10
11
9
10
10
11
11
20
25
30
40
50
6
6
7
7
8
6
7
7
8
8
7
7
8
8
9
7
8
8
9
9
8
8
9
9
10
12
12
13
13
14
12
13
13
14
14
13
13
14
14
16
60
75
100
125
150
10
10
11
11
12
10
11
11
12
12
11
11
12
12
13
11
12
12
13
13
12
12
13
13
14
60
75
100
125
150
8
9
9
10
10
9
9
10
10
11
9
10
10
11
11
10 10
10 11
11 11
11 . . .
... ...
14
14
16
16
16
14
16
16
16
16
16
16
16
16
16
16
16
16
16
...
200
250
300
350
400
12
13
13
14
14
13
13
14
14
14
13 14
14 14
14 . . .
... ...
... ...
14
...
...
...
...
200
250
300
350
400
11
11
...
...
...
11
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
16 16
16 16
16 . . .
... ...
... ...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
450
500
600
700
800
14
14
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
450
500
600
700
800
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
3/4
...
...
...
...
...
3/4
7 1/2 . . . . . . . . . . . . . . .
10
6
6
6
6
6
15
6
6
6
6
7
20
6
6
6
7
7
25
6
6
7
7
8
7 1/2 . . . . . . . . . . . . . . .
10 . . . . . . . . . . . . . . .
15
6
6
6
6
6
20
6
6
6
6
6
25
6
6
6
6
7
7 1/2
10
15
20
25
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
7 1/2
10
15
20
25
6
6
6
6
6
6
6
6
6
7
6
6
6
7
7
6
6
7
7
8
6
6
7
8
8
30
40
50
60
75
7
7
8
8
9
7
8
8
9
9
8
8
9
9
10
8
9
9
10
10
9
9
10
10
11
30
40
50
60
75
6
7
7
8
8
7
7
8
8
9
7
8
8
9
9
8
8
9
9
10
8
9
9
10
10
30
40
50
60
75
6
6
6
7
7
6
6
7
7
8
6
7
7
8
8
7
7
8
8
9
7
8
8
9
9
30
40
50
60
75
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
6
6
6
7
7
6
6
7
7
8
100
125
150
200
250
9
10
10
11
11
10
10
11
11
12
10
11
11
12
12
11
11
12
12
13
11
12
12
13
13
100
125
150
200
250
9
9
10
10
11
9
10
10
11
11
10
10
11
11
12
10
11
11
12
12
11
11
12
12
13
100
125
150
200
250
8
8
9
9
10
8
9
9
10
10
9
9
10
10
11
9
10
10
11
11
10
10
11
11
12
100
125
150
200
250
6
7
7
8
8
7
7
8
8
9
7
8
8
9
9
8
8
9
9
10
8
9
9
10
10
300
350
400
500
600
12
12
12
13
13
12
12
13
13
14
13
13
13
14
14
13 14
14 14
14 14
14 . . .
... ...
300
350
400
500
600
11
12
12
12
13
12
12
12
13
13
12
12
13
13
13
13
13
13
14
14
13
14
14
14
...
300
350
400
500
600
10
11
11
11
12
11
11
11
12
12
11
12
12
12
13
12
12
12
13
13
12
12
13
13
14
300
350
400
500
600
9
9
9
10
10
9
10
10
10
11
10
10
10
11
11
10 11
11 11
11 11
11 . . .
... ...
14 14
14 14
14 . . .
... ...
...
...
...
...
...
...
...
...
. . . 700
. . . 800
. . . 900
. . . 1000
13
13
14
14
13
14
14
14
14
14
14
...
14
...
...
...
. . . 700
. . . 800
. . . 900
. . . 1000
12
12
13
13
12
13
13
13
13
13
14
14
14
14
14
14
14 700
14 800
. . . 900
. . . 1000
11
11
11
11
11
11
...
...
...
...
...
...
...
...
...
...
700
800
900
1000
F18
...
...
...
...
TYPE J SURE-FLEX
BTS FOR CLOSE COUPLED APPLICATIONS
FLANGES
Type
COUPLINGS
DIMENSIONS (in.)
STOCK BORES*
Product
No.
3J
4J
5J
6J
Dimensions
C
51/64
55/64
1-3/64
1-5/16
D
2.062
2.460
3.250
4.000
E
13/32
27/64
29/64
9/16
G
3/8
5/8
3/4
7/8
H
1-1/2
1-5/8
1-7/8
2-1/2
L
1-31/32
2-11/32
2-27/32
3-1/2
T
25/64
7/16
19/32
3/4
X
5/8
5/8
59/64
1-3/32
Wt.
(lbs.)
3/8
0.3 X
0.4
0.9
1.2
(Inches)
1/2
X
X
X
5/8
X
X
X
X
3/4
X
X
X
X
7/8 15/16 1
X
X X X
X X X
X X X
Max
Bore 9
1-3/8
1-1/8 1-3/16 1-1/4
7/8 ...
1 ...
1-1/8 ...
X
X X
X X 1-3/8 ...
Millimeters
11
X
...
...
...
12
X
...
...
...
14
X
X
...
...
15
X
X
...
...
16
X
X
...
...
19
X
X
...
...
20 24 25
X X X
... ... ...
... ... ...
*We do not recommend reboring the 3J and 4J Flanges. See page F113 for standard keyseat
dimensions & F110 for bore tolerances.
Approximate weight for each flange.
F19
TYPE S SURE-FLEX
BTS FOR CLOSE COUPLED APPLICATIONS
FLANGES
Type S flanges are made of highstrength cast iron and are bored-tosize for slip fit on standard shafts.
They are easy to install and remove,
and are available from stock in a
wide range of bore sizes. Type S
couplings may be used with any of
the sleeves shown on page F15.
Bore (in.)
Up to and
including 2
Over 2
Tolerance (in.)
+ .0005 to + .0015
+ .0005 to +.0020
DIMENSIONS (in.)
5S 1-11/32
1-5/8
6S 1-5/16
1-9/16
DIMENSIONS
D
3.250
4.000
4.000
4.000
29/64
17/32
17/32
25/32
23/32
7/8
7/8
7/8
1-7/8 2-13/16
2-1/2 3-1/2
2-1/2 3-1/2
2-13/16 4
Wt.
(lbs.)
T
19/32
25/32
25/32
25/32
31/32
1-3/32
1-3/32
1-3/32
STOCK BORES
Inches
1/2
5/8
3/4
13/16
7/8
15/16
1
1 1/16
1 1/8
1 3/16
1 1/4
1 5/16
1 3/8
1 7/16
1 1/2
1 9/16
1 5/8
1 11/16
1 3/4
1 7/8
1 15/16
2
2 1/16
2 1/8
2 3/16
2 1/4
2 3/8
2 7/16
2 1/2
2 5/8
2 3/4
2 7/8
3
3 3/8
3 7/16
3 5/8
3 7/8
3 15/16
Coupling
Size C
1.1 o X X X X X X X X X X
1.9
oX X X XX XX X X X X X
1.8
1.8
2.6
8S
4.4
3.7
9S
6.8
6.2
oX XX X
10.5
9.8
16.6
16.4
26.6
oX
2-23/32
2-11/16
3-7/16
11S
3-1/16
12S 4
10S
7.500
7.500
8.625
8.625
10.000
13/16
1-15/32
1-1/8
1-9/16
1-9/32
1-5/8
1-5/8
1-7/8
1-7/8
2-5/16
oX
o
18.875
4-3/4
X
X X
X
X X XX X X XX X X X XX X X
X
X
X X X XX X XX X X X X X X X X XX X XX X
X
X XX
X X
X X X
X X
X X
XX
o X
X
X
X in the chart denotes finished bore with keyseat and 2 setscrews; O is plain bore suitable for reboring.
Approximate weight for each flange.
F110
XX X XX X XX X X X X
X
XX X X XX X X XX X XX X X XX
13S 4-3/8 11.750 1-5/16 2-11/16 6-3/4 9-1/4 1-31/32 3-1/16 45.2
14S 4-1/2 13.875 1-1/16 3-1/4 7-1/2 9-7/8 2-1/4 3-1/2 69.1
16S
o
o
X X XX X
X X X X XX X
X X X
X
TYPE S SURE-FLEX
BTS FOR CLOSE COUPLED APPLICATIONS
COUPLINGS
Type S Sure-Flex couplings are
normally supplied with the twopiece E sleeve. However, any of the
sleeves shown on page F15 can
be used with Type S flanges.
Spacing between internal flange
hubs equals L minus 2 times C.
Spacing between shafts should be
greater than 1/8 in. and less than L
minus .85 times the sum of the two
bore diameters.
To order complete couplings,
specify coupling size with flange
symbol (S) giving bore and keyseat.
Refer to page F13 to order the
required coupling.
DIMENSIONS (in.)
STOCK BORES
Millimeters
Max. Bore
Standard Shallow
14 15 16 19 20 24 25 28 30 32 35 38 42 45 48 50 52 55 60 65 70 80 90 Keyseat Keyseat
Bore
K.S.
X X X XX X X X
X
Key
Bore K.S.
Bore
K.S.
Key
...
...
...
...
...
...
...
...
...
...
1-3/16
1-1/4
1-1/4
1/4 X 1/16
XX X X X XX X X
1-7/16
1-1/2
...
...
...
...
1-5/8
1-3/4
1-7/8
1-7/8
3/8 X 1/8
...
1/2 X 1/8
...
...
3/8 x 5/16 X 1-3/4 3/8 X 1/16 3/8 X 1/4 X 1-1/4 ...
...
...
...
...
1-7/8 1/2 X 1/8 1/2 X 3/8 X 1-9/16
1/2 X 3/8 X 1-7/8 ...
...
...
...
...
...
1-15/16
...
2-1/4
2-3/8
2-1/8
...
1/2 X 3/16
...
...
...
...
...
2-1/2
...
2-3/4
2-7/8
...
2-7/8
...
3-/4 X 1/8
...
3/4 X 1/2 X 2-1/4
...
...
...
...
...
...
2-3/4
...
3-1/8
3-3/8
2-7/8
...
3/4 X 1/4
...
...
...
...
...
...
...
3-3/8
...
3-7/16
3-7/8
3-7/16
3-7/8
7/8 X 3/16
1 X 1/4
X X X X X 3-7/8
3-15/16
...
...
...
4-1/2
...
...
...
...
...
...
X X X XX X X X
X X XX X X X X
X
XX
X X X X
XX X X X X XX X XX
X X X X
X X
Key
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
5-1/2
6
...
...
...
...
...
...
...
...
See charts on page F113
Some large bore Type S flanges are supplied with shallow keyseats. In these cases, a rectangular key is furnished. The bores involved are listed above.
1-5/8 for 1-1/2 bore, 1-5/16 for 1-5/8 bore.
...
F111
TYPE B BUSHED-FLEX
QD FOR CLOSE COUPLED APPLICATIONS
FLANGES
Type B flanges are made of highstrength cast iron the same as Types
S, C and SC Sure-Flex flanges. Type
B, however, is designed to
accommodate Woods Sure-Grip
Bushing for easy installation and
removal.
BUSHINGS
Sure-Grip Bushings offer convenient
mounting of the flange to the shaft
securely without setscrews. They
are tapered and are split through
both the bushing flange and taper to
provide a clamp fit, eliminating
wobble, vibration and fretting
corrosion. This is the same bushing
used in Woods sheaves and pulleys
and is readily available everywhere.
DIMENSIONS (in.)
Product Bushing
No.
Required
Dimensions
E
Max. *
Bore
15/
32
2
2
7/
8
2 11/16
3 3/16
1 1/8
1 7/16
3 3/8
3 1/2
4 1/16
4 3/4
25/
32
1 1/4
1 13/16
4.000
4.625
5.450
6.350
1 1/32
1 3/32
1 5/16
1 1/2
1 3/4
1 1/4
1 1/4
1 5/8
1 15/16
1.4
1.9
2.9
4.8
.8
.8
1.0
1.5
1 7/8
2
2 5/8
3 5/8
3 5/8
4 1/2
7.500
8.625
10.000
11.750
13.875
18.875
23/
32
3 7/8
4 5/8
6
6 5/8
6 5/8
7 1/4
1 5/8
1 7/8
2 5/16
2 11/16
3 1/4
4 3/4
5 1/2
6 1/4
7 1/2
8 3/4
9 7/8
12 3/4
1 7/32
1 1/2
1 11/16
1 31/32
2 1/4
2 3/4
2 1/2
2 15/16
3 1/2
3 15/16
3 15/16
4 1/2
7.8
12.0
18.0
31 .2
51.4
120.0
2.0
3.5
9.0
14.0
14.0
22.0
C1
C2
1
1
6B
7B
8B
9B
10B
JA
JA
SH
SD
SK
1 7/32
1 5/8
1 29/32
2 1/4
1 15/16
11B
12B
13B
14B
16B
SF
E
F
F
J
2 3/16
2 23/32
3 3/4
3 3/4
4 13/16
F112
Weight
(lbs.)
Flange Bushing
15/
32
9/
16
5/
8
11/
16
29/
32
1 1/16
1 1/16
1 1/4
25/
32
29/
32
2 3/8
2 11/16
3
3 1/2
4 1/4
TYPE B BUSHED-FLEX
QD FOR CLOSE COUPLED APPLICATIONS
COUPLINGS
Type B Sure-Flex Couplings are
normally supplied with the twopiece E sleeve, and can use any
EPDM or Neoprene sleeves. DO
NOT use Hytrel sleeves with Type B
couplings.
Spacing between internal flange
hubs equals L minus 2 times C.
Spacing between shafts should be
greater than 1/8 in. and less than G.
To
order
complete
couplings,
SURE-GRIP BUSHING
KEYSEAT DIMENSIONS (in.)
Bushing
JA
Bores
1/
2
1/
16
1
1/
2
SH
11 /
16
1
1
SD
7/
8
5/
8
SK
1/
16
1/
32
Standard
3/
8
11 /
16
Standard
3/
8
1/
8
13/
16
1/
2
1/
8
1/
2
1/
16
Bores
1/
2
SF
15/
16
5/
1
13/
16
15/
16
7/
8
Standard
15/
16
7/
8
Standard
5/
16
3
3
7/
8
1/
2
9/
16
1/
8
1/
16
5/
8
7/
8
3/
16
3/
32
5/
8
1/
16
15/
16
1/
4
1/
8
3/
4
1/
16
5/
16
3/
8
5/
16
5/
32
3/
4
1/
32
7/
16
3/
4
3/
8
3/
16
1/
2
7/
8
13/
16
15/
16
3/
16
1/
4
1/
2
1/
8
13/
16
1/
2
5/
8
7/
16
5/
16
1/
16
5/
8
No K.S.
15/
16
9/
16
7/
8
44
13/
16
5/
16
1/
16
13/
16
1x
1/
2
1/
4
1/
4
1/
2
1/
4
5/
8
5/
16
3/
4
3/
8
7/
8
7/
16
1/
2
5/
16
13/
16
1/
8
9/
16
1/
2
1/
4
5/
8
9/
16
1/
2
1/
2
3/
4
Standard
1x
3/
8
1x
1/
8
1/
4
3/
4
3/
16
No K.S.
Standard
7/
8
1/
8
Standard
3/
4
Depth
3/
16
1/
4
Width
3/
4
5/
16
Shaft Dia.
5/
8
1/
4
13
No K.S.
1/
8
1/
4
1
6 2 /2
9
3
2 /16 2 /4
Keyseat
1/
16
3/
4
Bushing
No K.S.
1/
2
1/
4
1/
4
3/
8
Standard
3/
16
1/
4
7/
16
1/
2
Keyseat
3/
4
1/
2
F113
Coupling
Size
4JSC
5SC
6SC
7SC
Required
Distance
Between
Shafts
3-1/2
3-1/2
3-1/2
4-3/8
5
3-1/2
4-3/8
5
3-1/2
8SC
4-3/8
5
3-1/2
4-3/8
9SC
10SC
11SC
5
7
7-3/4
4-3/4
5
7
7-3/4
10
4-3/4
5
7
7-3/4
10
7
12SC
13SC
14SC
7-3/4
10
7-3/4
7-3/4
Use
Flange
No.
4JSC35
5SC35
6SC35
6SC44
6SC50
7SC35
7SC44
7SC50
8SC35
8SC35-10
8SC44
8SC50
8SC50-10
9SC35
9SC44
9SC50
9SC50-11
9SC70-11
9SC78-11
10SC48
10SC50
10SC70-13
10SC78-13
10SC100-13
11SC48
11SC50
11SC70-14
11SC78-14
11SC100-14
12SC70
12SC70-14
12SC78
12SC78-14
12SC100-14
13SC78
14SC78
Use
Hub
No.
....
5SCH
6SCH-6SCHS
6SCH-6SCHS
6SCH-6SCHS
7SCH-7SCHS
7SCH-7SCHS
7SCH-7SCHS
8SCH-8SCHS
10SCH-10SCHS
8SCH-8SCHS
8SCH-8SCHS
10SCH-10SCHS
9SCH-9SCHS
9SCH-9SCHS
9SCH-9SCHS
11SCH-11SCHS
11SCH-11SCHS
11SCH-11SCHS
10SCH-10SCHS
10SCH-10SCHS
13SCH-13SCHS
13SCH-13SCHS
13SCH-13SCHS
11SCH-11SCHS
11SCH-11SCHS
14SCH
14SCH
14SCH
12SCH-12SCHS
14SCH
12SCH-12SCHS
14SCH
14SCH
13SCH-13SCHS
14SCH
Max. Bore
Std. KS
Dimensions
D
L (2)
Wt.
(lbs.)
1-1/8 (1)
1-1/8
1-3/8
1-3/8
1-3/8
1-5/8
1-5/8
1-5/8
1-7/8
2-3/8
1-7/8
1-7/8
2-3/8
2-1/8
2-1/8
2-1/8
2-7/8
2-7/8
2-7/8
2-3/8
2-3/8
3-3/8
3-3/8
3-3/8
2-7/8
2-7/8
3-7/8
3-7/8
3-7/8
2-7/8
3-7/8
2-7/8
3-7/8
3-7/8
3-3/8
3-7/8
2.460
3.250
4.000
4.000
4.000
4.625
4.625
4.625
5.450
5.450
5.450
5.450
5.450
6.350
6.350
6.350
6.350
6.350
6.350
7.500
7.500
7.500
7.500
7.500
8.625
8.625
8.625
8.625
8.625
10.000
10.000
10.000
10.000
10.000
11.750
13.875
5-5/8
5-5/8
5-7/8
6-3/4
7-3/8
6-3/8
7-1/4
7-7/8
6-7/8
8-1/8
7-3/4
8-3/8
9-5/8
7-1/2
8-1/4
8-7/8
10-3/8
12-3/8
13-1/8
9-3/8
9-5/8
13-5/8
14-3/8
16-5/8
10-5/16
10-3/8
14-5/8
15-3/8
17-5/8
12-7/8
14-5/8
13-5/8
15-3/8
17-5/8
14-3/8
15-3/8
5/8
3/4
7/8
7/8
7/8
1
1
1
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-7/16
1-7/16
1-7/16
1-7/16
1-7/16
1-7/16
1-5/8
1-5/8
1-5/8
1-5/8
1-5/8
1-7/8
1-7/8
1-7/8
1-7/8
1-7/8
2-5/16
2-5/16
2-5/16
2-5/16
2-5/16
2-11/16
3-1/4
....
9/16
3/4
3/4
3/4
5/8
5/8
5/8
13/16
13/16
13/16
1-3/16
1-3/16
1-1/16
1-1/16
1-1/16
1-3/16
1-3/16
1-3/16
1-3/16
1-3/16
1-7/8
1-7/8
1-7/8
1-3/16
1-3/16
2
2
2
1-1/2
2
1-1/2
2
2
1-7/8
2
2.7
4.5
7.3
8.1
8.7
9.9
10.8
11.4
15.2
23.2
16.4
17.4
27.2
18.6
22.2
23.2
40.4
48.2
51.0
37.6
38.4
72.0
76.0
88.0
54.5
54.7
86.1
90.3
102.7
88.1
99.1
91.9
103.3
115.7
129.6
179.9
Flange
No.
4JSC
5SC
4JSC35
5SC35
6SC35
6SC44
6SC50
7SC35
7SC44
7SC50
8SC35
8SC35-10
8SC44
8SC50
8SC50-10
9SC35
9SC44
9SC50
9SC50-11
9SC70-11
9SC78-11
10SC48
10SC50
10SC70-13
10SC78-13
10SC100-13
11SC48
11SC50
11SC70-14
11SC78-14
11SC100-14
12SC70
12SC70-14
12SC78
12SC78-14
12SC100-14
13SC78
14SC78
6SC
7SC
8SC
9SC
10SC
11SC
12SC
13SC
14SC
For
Distance
Between
Shafts*
3-1/8
3-1/2
3-1/2
4-3/8
5
3-1/2
4-3/8
5
3-1/2
3-1/2
4-3/8
5
5
3-1/2
4-3/8
5
5
7
7-3/4
4-3/4
5
7
7-3/4
10
4-3/4
5
7
7-3/4
10
7
7
7-3/4
7-3/4
10
7-3/4
7-3/4
For
Hub
Dimensions
...
5SCH
6SCH-6SCHS
6SCH-6SCHS
6SCH-6SCHS
7SCH-7SCHS
7SCH-7SCHS
7SCH-7SCHS
8SCH-8SCHS
10SCH-10SCHS
8SCH-8SCHS
8SCH-8SCHS
10SCH-10SCHS
9SCH-9SCHS
9SCH-9SCHS
9SCH-9SCHS
11SCH-11SCHS
11SCH-11SCHS
11SCH-11SCHS
10SCH-10SCHS
10SCH-10SCHS
13SCH-13SCHS
13SCH-13SCHS
13SCH-13SCHS
11SCH-11SCHS
11SCH-11SCHS
14SCH
14SCH
14SCH
12SCH-12SCHS
14SCH
12SCH-12SCHS
14SCH
14SCH
13SCH-13SCHS
14SCH
D
2.460
3.250
4.000
4.000
4.000
4.625
4.625
4.625
5.450
5.450
5.450
5.450
5.450
6.350
6.350
6.350
6.350
6.350
6.350
7.500
7.500
7.500
7.500
7.500
8.625
8.625
8.625
8.625
8.625
10.000
10.000
10.000
10.000
10.000
11.750
13.875
E
2-1/16
51/64
19/32
1-1/32
1-11/32
15/32
29/32
1-7/32
9/32
9/32
23/32
1-1/32
1-1/32
1/16
7/16
3/4
3/4
1-3/4
2-1/8
11/32
15/32
1-15/32
1-27/32
2-31/32
1/32
1/16
1-1/16
1-7/16
2-9/16
21/32
21/32
1-1/32
1-1/32
2-5/32
9/16
1/32
* Flanges can be mixed to form different Between-Shaft Dimensions. See chart page F116.
If using 10HS hub, 7/16-14NC x 2-1/4 long capscrew needed (not furnished).
H
2
2
2-1/2
2-1/2
2-1/2
2-13/16
2-13/16
2-13/16
3-1/4
4-3/8
3-1/4
3-1/4
4-3/8
3-5/8
3-5/8
3-5/8
5-1/4
5-1/4
5-1/4
4-3/8
4-3/8
6-1/8
6-1/8
6-1/8
5-1/4
5-1/4
6-1/2
6-1/2
6-1/2
5-3/4
6-1/2
5-3/4
6-1/2
6-1/2
6-1/8
6-1/2
Hub
No.
Max.
Bore
Plain
Bore
4JSC
5SC
6SC
5SCH
6SCH
6SCHS
7SCH
7SCHS
8SCH
1-1/8
1-1/8
1-3/8
7/8
1-5/8
7/8
1-7/8
...
1/2
5/8
...
5/8
...
3/4
8SCHS
9SCH
7/8
2-1/8
...
7/8
9SCHS
10SCH
10SCHS
11SCH
11SCHS
12SCH
12SCHS
13SCH
13SCHS
14SCH
1-1/2
2-3/8
1-5/8
2-7/8
1-7/8
2-7/8
2-1/2
3-3/8
2-1/2
3-7/8
...
1-1/8
...
1-1/8
...
1-3/8
...
1-3/8
...
1-5/8
7SC
8SC
9SC
10SC
11SC
12SC
13SC
14SC
FOR 4JSC the hub is an integral part of the flange. 4JSC x 1-1/8 has 1/4 x 1/16 shallow keyseat.
* See page F110 for bore tolerances F113 for std. keyseat dimensions.
T
7/16
19/32
23/32
23/32
23/32
25/32
25/32
25/32
29/32
29/32
29/32
29/32
29/32
1-1/32
1-1/32
1-1/32
1-1/32
1-1/32
1-1/32
1-7/32
1-7/32
1-7/32
1-7/32
1-7/32
1-1/2
1-1/2
1-1/2
1-1/2
1-1/2
1-11/16
1-11/16
1-11/16
1-11/16
1-11/16
1-31/32
2-1/4
1.3
1.3
2.0
2.4
2.7
2.5
3.0
3.3
3.7
3.5
4.3
4.8
5.5
4.1
5.9
6.4
7.0
10.9
12.3
9.8
10.2
14.5
16.5
22.5
12.5
12.6
16.3
18.4
24.6
23.4
21.3
25.3
23.4
29.6
38.4
55.2
STOCK BORES *
Coupling
Size
L
2-1/2
1-11/16
1-5/8
2-1/16
2-3/8
1-5/8
2-1/16
2-3/8
1-5/8
1-5/8
2-1/16
2-3/8
2-3/8
1-11/16
2-1/16
2-3/8
2-3/8
3-3/8
3-3/4
2-1/4
2-3/8
3-3/8
3-3/4
4-7/8
1-1/2
1-9/16
2-9/16
2-15/16
4-1/16
2-15/32
2-15/32
2-27/32
2-27/32
3-31/32
3-1/4
2-23/32
Wt.
(lbs.)
Dimensions
Wt.
(lbs.)
Cap Screws
Furnished
1-1/16
1-3/32
1-7/32
31/32
1-15/32
1-3/32
2
2
2-1/2
2-1/2
2-13/16
2-13/16
...
410 x 1-1/2
41/4 x 1-3/4
41/4 x 1-1/2
41/4 x 1-7/8
41/4 x 1-1/2
...
.8
1.4
1.1
2.0
1.5
1-23/32
1-7/32
3-1/4
3-1/4
45/16 x 2-1/4
45/16 x 1-3/4
3.2
2.0
1-31/32
1-17/32
2-11/32
1-21/32
2-23/32
1-29/32
2-31/32
2-17/32
3-11/32
2-15/32
3-27/32
3-5/8
3-5/8
4-3/8
4-3/8
5-1/4
5-1/4
5-3/4
5-3/4
6-1/8
6-1/8
6-1/2
43/8 x 2-3/4
43/8 x 2-1/4
47/16 x 3-1/4
47/16 x 2-1/2
41/2 x 3-1/2
41/2 x 2-3/4
45/8 x 4
45/8 x 3-1/2
45/8 x 4-1/2
45/8 x 3-1/2
45/8 x 5
4.2
3.7
7.4
5.5
12.2
9.3
16.6
14.1
19.9
16.0
24.2
F115
3-1/2
4-3/8
5
7
7-3/4
10
Use Flanges*
Spacing
Use Flanges*
2-(
2-(
2-(
2-(
2-(
2-(
3-15/16
4-1/4
4-11/16
5-1/4
5-5/8
5-11/16
6
6-1/16
6-3/8
6-3/4
7-3/16
7-3/8
7-1/2
8-1/2
8-7/8
) SC35
) SC44
) SC50
) SC70
) SC78
) SC100
SEMI-SPACER
COMBINATION
STANDARD
Spacing
Spacing
1-7/8
2-5/16
2-5/8
3-5/8
4
5-1/8
F116
Use Flanges*
S & SC35
S & SC44
S & SC50
S & SC70
S & SC78
S & SC100
TYPE C SURE-FLEX
A
Dimensions
D
4.000
4.625
1.16
1.41
5.450
1.59
6.350
7.500
8 625
1.97
2.28
25
7/8
3
1-1/16 3-1/4
4-3/4
5-7/16
1
1-3/16
1-1/8
3-7/8
6-1/ 8
1-3/8
1-7/16 4-1/4
1-11/16 5
1 7/8 5 3/8
7-7/16
8-11/16
9 7/ 8
1-9/16
1-13/16
2 1/8
DIMENSIONS (in.)
Flange
Size
6C
7C
8C
9C
10C
11C
12C
Stock Bores
Distance
Maximum Bore
Min.
Between
Bore Standard Shallow
Shafts
Keyseat Keyseat Min. Max.
7/8
1-1/8
1-5/8
1-7/8
1-7/8
2
2-5/16
2-3/4
3-7/16
1-3/8
2-1/4
2-3/8
2-9/16
1-5/8
1-5/8
1-7/8
1-7/8
2-1/2
2-7/8
3-3/8
3-3/ 8
2-11/16
3-1/16
3-9/16
4-1/8
4-7/8
4-5/8
5-1/4
5-7/8
6-1/2
Approx.
Wt.
(lbs.)*
Dimensions
C
1-15/16 4.000
2-3/16 4.625
1.16
1.41
7/8
3
1-1/16 3-1/4
4-3/4
5-7/16
1
1-3/16
2.6
3.6
5.450
1.59
1-1/8
3-7/8
6-1/ 8
1-3/8
6.5
3
6.350
3 -1/2 7.500
4
8.625
4-3/8 10.000
1.97
2.28
2.5
2.69
1-7/16 4-1/4
1-11/16 5
1-7/8 5-3/8
2-3/8
6
7-7/16
8-11/16
9-7/ 8
11-1/8
1-9/16
1-13/16
2-1/8
2-3/8
9.8
16.6
26.0
38.3
2-1/2
For Standard keyseat dimensions, see chart page F113. * Weight of one flange.
Bore (in.)
Tolerance (in.)
Up to and
including 2
+.0005 to +.0015
Over 2
+.0005 to +.0020
Size
Bore Range
KS
Key Furnished
6C
8C
9C
1-11/16 to 1-7/8
2-5/16 to 2-3/8
2-7/16 to 2-11/16
1/2 X 1/16
5/8 x 1/16
5/8 x 3/16
SURE-FLEX COUPLINGS
Installation Instructions
Sure-Flex flanges (outer metallic parts) and sleeves (inner
elastomeric members) come in many sizes and types. First,
determine the size and type of components being used.
Remove all components from their boxes, and loosely
assemble the coupling on any convenient surface. (Do not
attempt to install the wire ring on the two-piece E or N sleeve
at this time.) Also check maximum RPM values in the table
against operating speed. All rubber sleeves (EPDM and
Neoprene) have the same ratings for a given size and may be
used interchangeably. However, because rubber and Hytrel
sleeves have completely different ratings, they never should be
used interchangeably.
Inspect all coupling components and remove any protective
coatings or lubricants from bores, mating surfaces and
fasteners. Remove any existing burrs, etc. from the shafts.
Slide one coupling flange onto each shaft, using snugfitting keys where required. When using Type B flanges,
follow the instructions furnished with the Sure-Grip bushing.
Position the flanges on the shafts to approximately achieve
the Y dimension shown in the table. It is usually best to
have an equal length of shaft extending into each flange. Move
one flange to its final position. Torque fasteners to proper
values. Slide the other flange far enough away to install the
sleeve. With a two-piece sleeve, do not move the wire ring to its
final position; allow it to hang loosely in the groove adjacent to
the teeth.
1
2
3
Parallel
4
5
F118
Angular
9200
7600
7600
6000
5250
4500
3750
3600
3600
2800
2400
2200
1500
(Dimensions in inches)
Types JE, JN,
JES, JNS, E & N
Parallel Angular
.010
.010
.015
.015
.020
.020
.025
.025
.032
.032
.040
.045
.062
.035
.043
.056
.070
.081
.094
.109
.128
.151
.175
.195
.242
.330
Y
1.188
1.500
1.938
2.375
2.563
2.938
3.500
4.063
4.875
4.688
6.688
7.750
10.250
*Type H & HS
Parallel Angular
...
...
...
.010
.012
.015
.017
.020
.022
.025
.030
.035
...
...
...
...
.016
.020
.025
.028
.032
.037
.042
.050
.060
...
Y
...
...
...
2.375
2.563
2.938
3.500
4.063
4.875
5.688
6.625
7.750
...
DURA-FLEX COUPLINGS
SECTION
F2
FEATURES
Designed from the ground up using finite element analysis to maximize flex life.
Easy two piece element installation. No need to move the hubs during replacement.
One spacer size to handle most different between shaft spacings.
Light weight element absorbs shock loading and torsional vibration.
Same hubs used on both spacer and standard elements.
No lubrication.
Good chemical resistance.
Stock bore-to-size (BTS), Sure-Grip bushed (QD) and Taper-Lock bushed (TL) Hubs.
Class
A
B
C
Load
Uniform
Characteristics
Even loads - no shock - non
reversing - infrequent starts (up
to 10 per hour) - low starting
torques
Beaters, Blowers (lobe, vane), Compressors (centrifugal, rotary), Moderate Uneven loads - moderate shock
Conveyors - non uniformly loaded or fed (belt, bucket, chain,
shock Infrequent reversing-moderate
screw), Dredge Pumps, Fans (forced draft, propeller), Kilns,
torques
Paper Mills (calendars, converting machines, conveyors, dryers,
mixers, winders), Printing Presses, Pumps (gear, rotary),
Shredders, Textile Machinery (dryers, dyers)
Cranes (bridge, hoist, trolley), Fans (cooling tower), Generators
(welding), Hammer Mills, Mills (ball, pebble, rolling, tube,
tumbling), Pumps (oil well), Wire Drawing Machines
Heavy
shock
Prime Mover
Class
A
B
C
1.0
1.5
2.0
1.5
2.0
2.5
2.0
2.5
3.0
Note: The above applications depict the generally accepted conditions encountered in industry. Conditions subject to extreme
temperatures, abrasive dusts, corrosive liquids, excessively high starting torques, etc., must be considered as extra heavy
shock loads. These conditions will increase service factors. Consult TB Woods for these selections.
WE2 - WE80
WES2 - WES80
WE[2-80] x Bore
WE[4-80] - Bushing
WE[3-80] - TL Bushing
WE[20-80]R
Description
Standard element, sizes 2 through 80
Spacer element, sizes 2 through 80
BTS hubs - stock bore (specify bore size)
QD hubs (sizes 4 through 80, bushing not included)
TL hubs (sizes 3 through 80, bushing not included)
High speed rings - sizes 20-80 (standard for sizes 2-10)
Size 20 Example
WE20
WES20
WE20H138
WE20H
WE20HTL
WE20R
(continued)
Torque
(IN LBS)
Stiffness
in lbs/
Radian
Standard
10.55
20.27
30.54
51.37
80.52
127.73
202.70
305.43
424.83
694.17
1229.20
2194.50
190
365
550
925
1450
2300
3650
5500
7650
12500
22125
39500
3170
4710
5370
9820
15800
27600
42200
65200
123000
167000
205000
305000
7500
7500
7500
7500
7500
6600
5800
5000
4200
3800
3600
2000
HP @ RPM
Coupling
Size
100
1160
1750
WE2
WE3
WE4
WE5
WE10
WE20
WE30
WE40
WE50
WE60
WE70
WE80
.30
.58
.88
1.48
2.30
3.65
5.79
8.85
12.14
19.84
35.12
62.70
3.50
6.72
10.12
17.02
26.69
42.33
67.18
101.23
140.80
230.07
407.39
727.32
5.28
10.13
15.27
25.68
40.26
63.86
101.35
152.72
212.42
347.08
614.60
1097.30
Maximum Rpm
Spacer*
Max. Misalignment
Parallel
Angular
1/16
1/16
1/16
1/16
1/16
3/32
3/32
3/32
3/32
1/8
1/8
1/8
4
4
4
4
4
3
3
3
3
2
2
2
7500
7500
7500
7500
7500
4800
4200
3600
3100
2800
2600
1800
*Maximum spacer RPM = Maximum standard RPM if using optional high speed rings. Operating temperature range is 40 F to 200 F.
WE2H
O
X
XS
XS
WE3H
O
X
XS
XS
XS
XS
XS
XS
WE4H
WE5H
WE10H
WE20H
WE30H
WE40H
O
X
XS
XS
XS
XS
X
X
XS
XS
XS
XS
XS
XS
X
X
XS
X
S
X
XS
X
XS
XS
X
X
XS
X
XS
XS
XS
X
XS
XS
XS
WE50H
WE60H
WE70H
WE80H
OX
XS
X
XS
XS
X
X
X
XS
X
X
X
XS
X
XS
XS
X
X
XS
X
X
X
XS
X
X
XS
X
X
XS
XS
XS
X
X
XS
XS
O
X
XS
XS
XS
X
XS
X
X
X
XS
XS
XS
XS
XS
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1-1/8
1-3/8
1-11/16
1-7/8
2-1/8
2-3/8
O NO KEYSEAT
X STANDARD KEYSEAT
S STEEL HUB OPTION
MAX. BORE INCLUDES STANDARD KEYSEAT
* PRODUCT NUMBER EXAMPLE
2-7/8
3-3/8
3-5/8
4-1/2
X
6
TOLERANCE
+.0005 to +.0015
+.0005 to +.0020
F23
&
&
&
&
&
&
&
&
&
&
&
&
WES2
WES3
WES4
WES5
WES10
WES20
WES30
WES40
WES50
WES60
WES70
WES80
Max. Bore
3.70
4.24
4.52
5.40
6.48
7.36
8.41
9.71
11.34
12.53
14.00
16.00
1.85
2.32
2.6
3.13
3.65
4.48
5.42
6.63
8.13
8.75
9.25
11.3
0.94
1.50
1.69
1.75
1.88
2.06
2.31
2.50
2.75
3.25
3.62
4.87
1-1/8
1-3/8
1-5/8
1-7/8
2-1/8
2-3/8
2-7/8
3-3/8
3-5/8
4
4-1/2
6
OAL
MAX
OAL
MIN
Maximum
DBSE
Weight
lbs.
WE2
WE3
WE4
WE5
WE10
WE20
WE30
WE40
WE50
WE60
WE70
WE80
3.78
4.32
4.68
5.30
5.57
6.82
7.61
8.16
9.21
10.70
11.00
14.75
3.22
3.80
3.82
4.32
4.13
4.30
4.63
5.08
5.79
6.44
7.20
9.30
1.90
1.32
1.30
1.80
1.81
2.70
2.99
3.16
3.71
4.20
4.86
6.64
1.5
3.3
4.4
7.4
11.2
16.3
27.7
45.4
59.0
82.6
109.0
242.0
OAL
MAX
OAL
MIN
Maximum
DBSE
Weight
lbs.
WES2
WES3
WES4
WES5
WES10
WES20
WES30
WES40
WES50
WES60
WES70
WES80
5.72
8.02
8.38
8.50
8.76
11.17
11.65
11.89
12.31
16.28
16.81
19.73
5.72
7.28
7.28
7.28
7.28
9.35
9.35
9.35
9.35
12.40
12.50
12.50
4.04
5.02
5.00
5.00
5.00
7.05
7.03
6.89
6.81
9.78
9.57
9.77
2.5
4.8
6.1
9.4
13.6
19.2
31.0
48.9
63.5
91.0
128
258
Shaft Spacing from 1/4 up to the MAX DBSE can be accomodated by positioning hubs IN or OUT or by using various existing hole
patterns. OAL - Over All Length does Not include bolt heads
F24
&
&
&
&
&
&
&
&
&
&
WES4
WES5
WES10
WES20
WES30
WES40
WES50
WES60
WES70
WES80
Bushing
Max. Bore
4.52
5.40
6.48
7.36
8.41
9.71
11.34
12.53
14.00
16.00
2.60
3.13
3.65
4.48
5.42
6.63
8.13
8.75
9.25
11.3
1.00
1.25
1.31
1.88
2.00
2.63
2.63
3.63
4.50
6.75
JA
SH
SDS
SK
SF
E
E
F
J
M
1-1/4
1-11/16
2
2-5/8
2-15/16
3-1/2
3-1/2
4
4-1/2
5-1/2
OAL
MAX
OAL
MIN
Maximum
DBSE
Weight
lbs.
WE4
WE5
WE10
WE20
WE30
WE40
WE50
WE60
WE70
WE80
3.88
4.50
4.95
6.37
5.94
6.75
7.88
8.88
10.47
14.72
3.24
4.24
3.83
4.38
5.43
6.50
6.61
8.68
10.12
13.97
1.88
1.88
2.31
2.62
2.19
1.74
2.89
1.96
1.72
1.47
3.8
6.0
8.8
15.9
25.1
47.0
48.0
79.4
124
268
OAL
MAX
OAL
MIN
Maximum
DBSE
Weight
lbs.
WES4
WES5
WES10
WES20
WES30
WES40
WES50
WES60
WES70
WES80
7.58
7.71
8.14
10.72
9.98
10.48
10.98
14.46
15.41
17.85
7.28
7.28
7.28
9.35
9.35
9.35
9.35
12.40
12.50
14.35
5.58
5.08
5.50
6.97
6.23
5.47
5.99
7.54
6.65
4.60
5.5
8.0
11.2
18.8
28.4
50.5
52.5
106.8
143
284
Shaft Spacing from 1/4 up to the MAX DBSE can be accomodated by positioning hubs IN or OUT or by using various existing hole
patterns. OAL - Over All Length does Not include bolt heads
F25
&
&
&
&
&
&
&
&
&
&
&
WES3
WES4
WES5
WES10
WES20
WES30
WES40
WES50
WES60
WES70
WES80
Bushing
Max. Bore
4.24
4.52
5.40
6.48
7.36
8.41
9.71
11.34
12.53
14.00
16.00
2.32
2.60
3.13
3.65
4.48
5.42
6.63
8.13
8.75
9.25
11.3
0.88
0.88
0.88
1.00
1.00
1.25
1.75
1.75
2.00
3.50
4.00
TL1008
TL1008
TL1108
TL1310
TL1610
TL2012
TL2517
TL2517
TL3020
TL3535
TL4040
1
1
1-1/8
1-7/16
1-11/16
2-1/8
2-11/16
2-11/16
3-1/4
3-15/16
4-7/16
OAL
Maximum
DBSE
Weight
lbs.
WE3
WE4
WE5
WE10
WE20
WE30
WE40
WE50
WE60
WE70
WE80
3.44
3.44
3.94
4.06
4.50
5.06
5.88
6.50
7.31
9.38
11.75
1.69
1.69
2.19
2.06
2.50
2.56
2.38
3.00
3.31
2.38
3.75
1.8
2.6
4.0
6.0
9.0
13.6
21.8
31.5
46.6
66.7
82.0
OAL
MAX
OAL
MIN
WES3
WES4
WES5
WES10
WES20
WES30
WES40
WES50
WES60
WES70
WES80
7.28
7.28
7.28
7.28
9.35
9.35
9.59
9.59
12.90
14.34
14.84
7.28
7.28
7.28
7.28
9.35
9.35
9.35
9.35
12.40
12.50
14.35
Maximum Weight
DBSE
lbs.
5.38
5.38
5.38
5.25
6.87
6.60
6.11
6.11
8.90
7.34
6.84
3.2
4.2
6.0
7.9
11.9
18.0
26.8
37.4
60.7
81.4
93.2
F26
FEATURES
Metric Hardware
Designed from the ground up using finite element analysis to maximize flex life.
Easy two piece element installation. No need to move the hubs during replacement.
One spacer size to handle most different between shaft spacings.
Light weight element absorbs shock loading and torsional vibration.
Same hubs used on both spacer and standard elements.
No lubrication.
Good chemical resistance.
F27
Class
A
B
C
Load
Uniform
Characteristics
Even loads - no shock - non
reversing - infrequent starts (up
to 10 per hour) - low starting
torques
Beaters, Blowers (lobe, vane), Compressors (centrifugal, rotary), Moderate Uneven loads - moderate shock
Conveyors - non uniformly loaded or fed (belt, bucket, chain,
shock Infrequent reversing-moderate
screw), Dredge Pumps, Fans (forced draft, propeller), Kilns,
torques
Paper Mills (calendars, converting machines, conveyors, dryers,
mixers, winders), Printing Presses, Pumps (gear, rotary),
Shredders, Textile Machinery (dryers, dyers)
Cranes (bridge, hoist, trolley), Fans (cooling tower), Generators
(welding), Hammer Mills, Mills (ball, pebble, rolling, tube,
tumbling), Pumps (oil well), Wire Drawing Machines
Heavy
shock
Prime Mover
Class
A
B
C
1.0
1.5
2.0
1.5
2.0
2.5
2.0
2.5
3.0
Note: The above applications depict the generally accepted conditions encountered in industry. Conditions subject to extreme
temperatures, abrasive dusts, corrosive liquids, excessively high starting torques, etc., must be considered as extra heavy
shock loads. These conditions will increase service factors. Consult TB Woods for these selections.
F28
Part #
Description
Size 20 Example
Element (1)
WE2M WE80M
WES2M WES80M
WE20M
WES20M
Hubs (2)
WE[2-80] MPB
WE[3-80] TL Bushing
WE20MMPB
WE20MTL
HS Rings (1)
WE[20-80]R
WE20RM
KW @ RPM
100
970
1450
3000
WE2M
0.22
2.17
3.24
6.71
WE3M
0.43
4.20
6.27
12.98
WE4M
.66
6.37
9.52
19.69
WE5M
1.10 10.71 16.00
33.11
WE10M 1.72 16.64 24.87
51.45
WE20M 2.72 26.40 39.47
81.65
WE30M 4.32 41.88 62.61 129.53
WE40M 6.60 64.01 95.69 197.98
WE50M 9.05 87.81 131.27 271.58
WE60M 14.79 143.51 214.52 443.84
WE70M 26.19 254.03 379.74 785.67
WE80M 46.76 453.53 677.95 1402.66
Torque Stiffness
(Nm) NM/RAD
21.47
41.24
62.14
104.5
163.8
259.9
412.4
621.4
864.3
1412
2500
4463
358
532
607
1110
1790
3120
4770
7370
13900
18900
23200
34500
Maximum Rpm
Standard Spacer*
7500
7500
7500
7500
7500
6600
5800
5000
4200
3800
3600
2000
7500
7500
7500
7500
7500
4800
4200
3600
3100
2800
2600
1800
Max. Misalignment
Parallel
(MM)
1.6
1.6
1.6
1.6
1.6
2.4
2.4
2.4
2.4
3.2
3.2
3.2
Angular
4
4
4
4
4
3
3
3
3
2
2
2
*Maximum spacer RPM = Maximum standard RPM if using optional high speed rings
F29
Max Bore
94
108
115
137
165
187
214
247
288
318
356
406
47
59
66
80
93
114
138
168
207
222
235
287
24
38
43
44
48
52
59
64
70
83
92
124
29
35
41
48
54
60
73
86
92
102
114
152
OAL
MAX
OAL
MIN
Maximum
DBSE
Weight
kg
WE2M
WE3M
WE4M
WE5M
WE10M
WE20M
WE30M
WE40M
WE50M
WE60M
WE70M
WE80M
96
110
119
135
141
173
193
207
234
272
279
375
82
97
97
110
105
109
118
129
147
164
183
236
48
34
33
46
46
69
76
80
94
107
123
169
.07
1.5
2.0
3.4
5.1
7.4
12.6
20.6
26.8
37.5
49.4
110
OAL
MAX
OAL
MIN
Maximum
DBSE
Weight
kg
WES2M
WES3M
WES4M
WES5M
WES10M
WES20M
WES30M
WES40M
WES50M
WES60M
WES70M
WES80M
145
204
213
216
223
284
296
302
313
414
427
501
145
185
185
185
185
237
237
237
237
315
318
318
103
128
127
127
127
180
180
175
173
248
243
248
1.1
2.2
2.8
4.3
6.2
8.7
14.1
22.2
28.8
41.3
58.1
117
F210
Bushing
Max Bore
108
115
137
165
187
214
247
288
318
356
406
59
66
80
93
114
138
168
207
222
235
287
22
22
22
25
25
32
44
44
51
89
102
TL1008
TL1008
TL1108
TL1310
TL1610
TL2012
TL2517
TL2517
TL3020
TL3535
TL4040
26
26
29
36
44
55
68
68
82
100
113
OAL
Maximum
DBSE
Weight
kg
WE3M
WE4M
WE5M
WE10M
WE20M
WE30M
WE40M
WE50M
WE60M
WE70M
WE80M
87
87
100
103
114
129
149
165
186
238
298
43
43
56
52
64
65
60
76
84
60
95
0.8
1.2
1.8
2.7
4.1
6.2
9.9
14.3
21.1
30.3
37.2
OAL
MAX
OAL
MIN
Maximum
DBSE
Weight
kg
WES3M
WES4M
WES5M
WES10M
WES20M
WES30M
WES40M
WES50M
WES60M
WES70M
WES80M
185
185
185
185
237
237
244
244
328
364
377
185
185
185
185
237
237
237
237
315
318
318
137
137
137
133
174
168
155
155
226
186
174
1.5
1.9
2.7
3.6
5.4
8.2
12.2
17.0
27.5
36.9
42.3
F211
Sure-Flex
Operates in shear
No lubrication
Four-way flexibility
Easy installation
Up to 115 HP
@ 100 rpm
Gear Couplings
High Torque Capacity
Torsionally Stiff
Good Inherent Balance
Rated for Higher Speeds
Many Types and Configurations
Up to 2714 HP
@ 100 rpm
Jaw Couplings
Form-Flex
All metal construction
No lubrication
Wide temperature range
Zero backlash
API offering
Economical
No maintenance
Industry standard
Large inventories
Up to 3175 HP
@ 100 rpm
Up to 30 HP
@ 100 rpm
SECTION
F3
L-JAW
Straight Jaw
100% interchangeable with
industry standard
4 Insert materials available
Large selection of sizes
C-JAW
Straight Jaw
Uses individual cushions
For higher torque loads
Cushions easily replaced
F31
Class
A
B
C
Load
Characteristics
Prime Mover
Class
A
B
C
F32
L-JAW
Product No.
Description
Driver Hub
Driven Hub
L09958
L09912NK
L099 x 5/8
L099 x 1/2
Insert
L099N
L099 Buna-N
Cover
none
none
no keyseat
C-JAW
Product No.
Description
C280178
C280158
C280 x 1-7/8
C280 x 1-5/8
C280N
C280 Buna-N
C280CH
C280 Cover
(contains 6 cushions)
w/ hardware
L-JAW TYPE
PRODUCT
NO.
MAX
BORE
MAX
RPM
TORQUE
IN. LBS
L035
L050
L070
L075
L090
1. L095
L099
2. L100
L110
L150
L190
L225
L276
3/8
5/8
3/4
7/8
1
1-1/8
1-3/16
1-7/16
1-5/8
1-7/8
2-1/8
2-5/8
2-7/8
31000
18000
14000
11000
9000
9000
7000
7000
5000
5000
5000
4600
4200
3.5
26.3
43.2
90.0
144.0
194.0
318.0
417.0
792.0
1240.0
1726.0
2340.0
4716.0
0.006
0.042
0.069
0.143
0.228
0.308
0.505
0.662
1.257
1.967
2.739
3.713
7.483
0.07
0.50
0.82
1.71
2.74
3.69
6.05
7.94
15.08
23.61
32.86
44.55
89.79
0.10
0.75
1.23
2.57
4.11
5.54
9.08
11.91
22.62
35.41
49.29
66.83
134.69
0.20
1.50
2.47
5.14
8.23
11.08
18.16
23.82
45.24
70.83
98.59
133.66
269.38
TORQUE
IN. LBS.
50.0
114
227
401
561
792
1134
2268
3708
4680
6228
0.079
0.181
0.360
0.636
0.890
1.257
1.799
3.599
5.883
7.426
9.882
0.95
2.17
4.32
7.64
10.68
15.08
21.59
43.18
70.60
89.11
118.58
1.43
3.26
6.48
11.45
16.02
22.62
32.39
64.77
105.90
133.66
177.87
2.86
6.51
12.97
22.91
32.04
45.24
64.77
129.55
211.80
267.32
355.74
C-JAW TYPE
PRODUCT
NO.
MAX
BORE
MAX
RPM
TORQUE
IN. LBS
C226
C276
C280
C285
C295
C2955
2-1/2
2-7/8
3
4
3-1/2
4
4800
4200
3500
3200
2300
2300
2988.0
4716.0
7560.0
9182.0
11340.0
18900.0
4.700
7.500
12.000
14.600
18.000
30.000
56.40
90.00
144.00
175.20
216.00
360.00
84.60
135.00
216.00
262.80
324.00
540.00
169.20
270.00
432.00
525.60
648.00
1080.00
SPIDER CHARACTERISTICS
CHARACTERISTICS
OIL RESISTANCE
CHEMICAL RESISTANCE
FLEXIBILITY
TEMPERATURE
F
RANGE
C
TORSIONAL STIFFNESS
AVERAGE HARDNESS
(SHORE NUMBER)
MAX. MISALIGNMENT
ANGULAR
PARALLEL
AVAILABILITY L-JAW
C-JAW
BUNA-N (N)
URETHANE (U)
HYTREL (H)
BRONZE (B)
GOOD
POOR
EXCELLENT
40 TO +212
40 TO +100
FULL SOFT
GOOD
GOOD
GOOD
30 TO +160
35 TO +71
MEDIUM SOFT
EXCELLENT
EXCELLENT
FAIR
60 TO +250
51 TO +121
HARD
EXCELLENT
EXCELLENT
POOR
40 TO +450
40 TO +232
HARD
80A
90A
55D
1
.015
X
X
1
.015
X
1/2
.015
X
1/2
.010
X
TO ORDER SPIDER
OR CUSHION SET
SPECIFY THE
COUPLING SIZE WITH
THE MATERIAL
SUFFIX.
EXAMPLE:
L150H =
HYTREL SPIDER FOR
L150 COUPLING
F33
STOCK BORES
STOCK L-JAW INCH HUBS
BORE
(IN.)
PRODUCT
NO.
1/8
3/16
1/4
5/16
3/8
7/16
1/2
9/16
5/8
11/16
3/4
7/8
15/16
1
1 1/16
1 1/8
1 3/16
1 1/4
1 5/16
1 3/8
1 7/16
1 1/2
1 9/16
1 5/8
1 11/16
1 3/4
1 13/16
1 7/8
1 15/16
2
2 1/16
2 1/8
2 3/16
2 1/4
2 3/8
2 1/2
2 5/8
2 7/8
18
3/16
14
5/16
38
7/16
12
9/16
58
11/16
34
78
15/16
1
1116
118
1316
114
1516
138
1716
112
1916
158
11116
134
11316
178
11516
2
2116
218
2316
214
238
212
258
278
0 NO KEYSEAT
L035
0
0
X
0
X
L050
L070
L075
L090
X
0
X
X
X
1
X
X
X
X
X
X
1
X
1
1
X
0
X
X
X
X
1
1
1
1
X
X
X
X
X
1
1
1
X
1
1
1
L095
L099
L100
X
X
1
1
1
1
1
1
1
1
1
X
X
1
1
1
1
1
1
1
X
X
X
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
L110
L150
L190
L225
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
X
1
1
1
X
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
L276
1
1
1
1
1
1
1
1
1 STANDARD KEYSEAT
BORE TOLERANCES
F34
BORE SIZE
TOLERANCE
UP TO AND
INCLUDING 2
+.0005
+.0015
OVER 2
+.0005
+.0020
Width
Depth
1/2 - 9/16
5/8 - 7/8
15/16 - 1-1/4
1-5/16 - 1-3/8
1/8
3/16
1/4
5/16
1/16
3/32
1/8
5/32
1-7/16 - 1-3/4
1-13/16 - 2-1/4
2-5/16 - 2-3/4
2-13/16 - 3-1/4
3/8
1/2
5/8
3/4
3/16
1/4
5/16
3/8
3-5/16 - 3-3/4
3-13/16 - 4-1/2
4-9/16 - 5-1/2
5-9/16 - 6-1/2
7/8
1
1-1/4
1-1/2
7/16
1/2
5/8
3/4
STOCK BORES
STOCK L-JAW METRIC BORE HUBS
BORE
(MM)
PRODUCT
NO.
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
22
24
25
28
30
32
35
38
40
42
45
48
50
55
60
65
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
22
24
25
28
30
32
35
38
40
42
45
48
50
55
60
65
0 NO KEYSEAT
L035
L050
L070
L075
L090
L095
L099
L100
L110
C-JAW HUBS
L150
L190
L225
L276
0
1
0
0
0
X
1
1
X
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 STANDARD KEYSEAT
BORE
SIZE
SOLID
1/8
3/16
1/4
5/16
3/8
7/16
1/2
9/16
5/8
11/16
3/4
7/8
15/16
1
1 1/16
1 1/8
1 3/16
1 1/4
1 5/16
1 3/8
1 7/16
1 1/2
1 9/16
1 5/8
1 11/16
1 3/4
1 7/8
1 15/16
2
2 1/8
2 1/4
2 3/8
2 1/2
2 5/8
2 7/8
3
3 3/8
3 1/2
3 5/8
3 3/4
3 7/8
PRODUCT
C226
NO.
S
18
3/16
14
5/16
38
7/16
12
9/16
58
11/16
34
78
15/16
1
1116
118
1316
114
1516
138
1716
112
1916
158
11116
134
178
11516
2
218
214
238
212
258
278
3
338
312
358
334
378
C276
C280
C285
C295
C2955
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
BORE TOLERANCES
BORE SIZE
TOLERANCE
UP TO AND
INCLUDING 2
+.0005
+.0015
OVER 2
+.0005
+.0020
Shaft Dia.
Width
Depth
1/2 - 9/16
5/8 - 7/8
15/16 - 1-1/4
1-5/16 - 1-3/8
1/8
3/16
1/4
5/16
1/16
3/32
1/8
5/32
1-7/16 - 1-3/4
1-13/16 - 2-1/4
2-5/16 - 2-3/4
2-13/16 - 3-1/4
3/8
1/2
5/8
3/4
3/16
1/4
5/16
3/8
3-5/16 - 3-3/4
3-13/16 - 4-1/2
4-9/16 - 5-1/2
5-9/16 - 6-1/2
7/8
1
1-1/4
1-1/2
7/16
1/2
5/8
3/4
F35
COUPLING DIMENSIONS
L-JAW DIMENSIONS
Coupling Hub
Size
Matl
L035
L050
L070
L075
L090
L095
L099
L100
L110
L150
L190
L225
L276
S.I.
S.I.
S.I.
S.I.
S.I.
S.I.
S.I.
S.I.
S.I.
S.I.
C.I.
C.I.
C.I.
OD
DIMENSIONS
HD
LTB
B
0.63
1.08
1.36
1.75
2.11
2.11
2.53
2.53
3.33
3.75
4.50
5.00
6.19
0.63
1.08
1.36
1.75
2.11
2.11
2.53
2.53
3.33
3.75
4.00
4.25
5.00
0.27
0.63
0.75
0.81
0.81
1.00
1.06
1.38
1.69
1.75
1.94
2.19
3.13
0.81
1.72
2.00
2.13
2.13
2.50
2.88
3.50
4.23
4.50
4.88
5.38
7.88
Weight
Lbs*
0.28
0.47
0.50
0.50
0.50
0.50
0.75
0.75
0.85
1.00
1.00
1.00
1.63
0.10
0.30
0.60
1.00
1.50
1.80
2.50
3.50
6.60
9.10
17.00
23.00
47.00
Weight
Lbs*
1.50
1.63
1.63
1.63
1.88
1.88
29.00
47.00
61.00
87.00
97.00
117.00
C-JAW DIMENSIONS
Coupling Hub
Size
Matl
C226
C276
C280
C285
C295
C2955
C.I.
C.I.
C.I.
C.I.
C.I.
C.I.
OD
HD
5.15
6.18
7.50
8.50
9.12
9.12
4.12
5.00
5.50
6.50
6.31
7.12
DIMENSIONS
LTB
B
2.75
3.12
3.12
3.75
3.75
4.25
7.00
7.87
7.87
9.13
9.38
10.38
F36
HD ELASTOMERIC COUPLINGS
SECTION
F4
Couplings require no lubrication and have proven to be technically superior, low in cost, simple in design, rugged,
corrosion resistant, and maintenance-free. These couplings will tolerate substantial misalignment, and control shock
loads. Replacement of the urethane rolls, if required, is a simple operation, taking a matter of minutes and involving no
special skills or tools. Installation and alignment is quick and easy.
ROLL UNDER
LIGHT LOAD.
ROLL UNDER
HEAVY LOAD.
HOW IT WORKS
The Elastomeric line of couplings uses the strength
continuously roll and adjust their positions to
and resiliency of urethane, plus the rolling ability of the
accommodate whatever misalignment is present.
cylindrical elements, to transmit torque without causing
Increasing torque deforms the rolls bringing more and
lateral forces or moments to be applied to either shaft.
more urethane into play. This means that the torqueMisalignment is permitted by the generous clearances deflection characteristics of the coupling are non linear, a
within the metallic parts of the coupling. The urethane
fact that gives the coupling a distinct advantage in
rolls key the male and female hubs together and seek their
controlling torsional vibrations.
own position in the pockets formed by the hubs. They
F41
STANDARD SERIES HD
ELASTOMERIC COUPLINGS
The standard HD elastomeric coupling consists of one male and one female hub with a set of eight straight rolls.
This coupling is used for straight shaft connections. The hubs are cast iron. The rolls are made of urethane.
Finished bored coupling hubs are provided with a class 1 clearance fit, standard keyway, and setscrew over
the keyway.
SIZE
HD2
HD3
HD4
HD5
HD6
HD7
HD8
MAX BORE
MALE
FEMALE
0.88
1.00
1.18
1.38
1.63
1.88
2.25
2.50
2.75
3.00
3.75
3.93
5.13
5.50
A
3.00
4.09
5.38
7.00
8.38
11.00
15.25
DIMENSIONS IN INCHES
C
D
E
1.31
0.09
1.19
1.68
0.12
1.62
2.25
0.12
2.19
2.43
0.18
2.44
2.93
0.18
2.93
3.93
0.25
3.93
5.44
0.38
5.44
B
2.59
3.42
4.56
5.05
6.04
8.11
11.26
MAX RPM
F
1.50
2.00
2.75
3.50
4.25
5.75
8.00
G
1.75
2.25
3.00
4.00
4.75
6.25
8.50
3600
3600
3600
3600
2900
2100
1800
WEIGHT
LBS
2.25
5.25
11.00
23.00
41.00
88.00
250.00
PARALLEL
OFFSET-MAX
0.03
0.03
0.04
0.04
0.05
0.05
0.06
F42
ELECTRIC MOTOR
OR STEAM TURBINE
ENGINEMORE
THAN 6 CYLINDERS
ENGINELESS
THAN 6 CYLINDERS
1.0
1.5
2.0
1.5
2.0
2.5
2.0
2.5
3.0
COUPLING DATA
RATED TORQUE:................................................. 3600 IN. LBS.
FREE END FLOAT:............................................... +/- .100
MAXIMUM DBSE:................................................. 162 INCHES
MAX INSTALLATION CLEARANCE:..................... 5 DEGREES
WEIGHTLBS @ 36 DBSE:................................ 16.1 LBS.
WEIGHTLBS ADD PER INCH:........................... 0.11 LBS.
CLASS
A
C
E
MATERIALS USED
HUB
HARDWARE
STEEL
STEEL
ZINC PLATED STEEL
304 STAINLESS STEEL
304 STAINLESS STEEL 304 STAINLESS STEEL
HD FLYWHEEL COUPLING
The HD Flywheel coupling is designed for
use on close coupled engine driven
equipment. This coupling is designed with
limited clearance between the roll and the
male and female coupling halves to assure
long life when used with reciprocating
engine drivers. Heavy duty rolls are
long life when used with reciprocating
engine drivers. Heavy duty rolls are
standard on this series. The male half and
rolls may be installed blind into the female
half bolted to an engine flywheel.
Hubs are made of steel material.
Flywheel adapters are cast iron.
SIZE
SIZE
HD5.5
HD6.5
HD7.5
RATED TORQUE
IN LBS
HP/100RPM
12000
22000
55440
19.0
34.9
88.0
HD5.5
HD6.5
HD7.5
WEIGHT
lbs
27.9
32.9
49.2
MAX
BORE
2.62
3.25
4.25
7.00
8.38
11.00
3.25
3.63
4.50
WR2
LB IN2
571.5
648.0
1071.0
TQ/RAD
X106 IN LBS/RAD
.120
.249
.786
MISALIGNMENT RATINGS
ANGULAR
PARALLEL
AXIAL
1 DEG.
+/-.020
+/-.060
1 DEG.
+/-.020
+/-.060
1 DEG.
+/-.020
+/-.060
DIMENSIONS IN INCHES
C
D
F
0.50
0.63
0.63
0.50
0.25
0.25
2.75
3.38
4.25
1.83
2.25
2.91
3.80
4.48
6.14
1.31
1.56
2.06
RATED TORQUE:
180 IN LBS
RATED MISALIGNMENT:
F43
Neoprene R
EPDM
Urethane
Hytrel
B
A
A(158F)
X
A
B(158F)
A
C
C
C
A
C
X
C
C
B
A(158F)
A(158F)
A
B
A(158F)
A
A
B
A
B
C
B(158F)
A(158F)
A
C
B
C
B
T
A
T
A
C
C
C
C
C
X
C
B
C
X
C
T
...
A
A
X
B-C
T
...
T
T
T
X
...
X
T
X
C
T
A
T
T
C
T
A
T
A(158F)
B(158F)
A
B(122F)
C
C(158F)
A
C(122F)
X
C
X
B
C
B
B
B
A
B
B
T
C
C
X
B
C
A
B
C
C
C
T
B
...
T
A
A
A
A
A
B
B
A
C
X
C
...
...
A
A
A
A
A
A
B
T
A
T
B
A
A
A
A
B
C
C
...
B-C
A(158F)
A
B(158F)
A(158F)
B-C
A
C
C
C
A(212F)
X
X
T
A
T
T
T
T
C
X
C
A(158F)
C
X
A
T
A
T
C
A
C(122F)
C
C
A(122F)
C
X
A
A
T
A
C
T
B
C
...
A(158F)
B
SECTION
F5
FORM-FLEX
FLEXIBLE DISC
COUPLINGS
Long Life
Low Maintenance
Design Flexibility
F51
F52
Form-Flex floating shaft couplings are a costeffective, maintenance free alternative to cardan
U-joints for vertical pump drivelines. Form-Flex
couplings are available with either steel or composite
spacer tubing. Composite spacer tubing can reduce
total cost by eliminating the need for bearings and
support structures.
OVER 30 YEARS
EXPERIENCE IN
METAL DISC
COUPLINGS
HIGH STRENGTH
STAINLESS STEEL
FLEX DISCS
-HIGH TORSIONAL STIFFNESS
-NO LUBRICATION REQUIRED
APPLICATIONS
-PUMPS
-COMPRESSORS
-PRINTING
TYPICAL APPLICATIONS
PUMPS
Form-Flex spacer and close couple designs are ideally
suited for all types of pump applications
PRINTING
Form-Flex couplings high torsional stiffness allows
precise registration for high quality printing lineshaft
applications
POSITIONING SYSTEMS
Zero backlash and high torsional stiffness make
Form-Flex the first choice for servo and stepper drives
F53
DISC STYLE
DESIGN FEATURES
4 BOLT
(A, M SERIES)
WHERE USED
Zero backlash.
8 BOLT
(D, F, H SERIES)
Zero backlash.
Heavy duty cast construction.
Alloy or stainless steel flex discs.
Flywheel mount designs.
MATERIAL CLASSES
APPLIES TO 4 AND 6 BOLT DESIGNS
COUPLING
DESCRIPTION
Mild steel hubs and spacer, alloy steel hardware, 300 series SS flex disc
Zinc plated steel hubs and spacer, alloy steel hardware, 300 series SS flex disc
Zinc plated steel hubs and spacer, 300 series SS flex disc and hardware
AR, AK, AP
AX, AY
BH, BP, BY
DP*
BF
BA, DA*
A5, A7
CLEARANCE
INTERFERENCE
CLEARANCE
SET SCREWS
STANDARD
OPTIONAL
STANDARD
PULLER HOLES
OPTIONAL
STANDARD
OPTIONAL
HFTH
AGMA 7
AGMA 8
AGMA 9
OPTIONAL
AGMA 7
INTERFERENCE
OPTIONAL
STANDARD
*Alloy steel flex disc is standard for DA and DP series. Stainless steel is optional.
F5-4
B5
OPTIONAL
ALLOY STEEL
N/A
PER TBW COMMERCIAL STANDARD
N/A
N/A
COUPLING/APPLICATION TYPES
COUPLING
TYPE
SINGLE
FLEX
CLOSE
COUPLE
DOUBLE
FLEX
SPACER
COUPLINGS
DOUBLE
FLEX
TYPICAL APPLICATIONS
PAGE
AR
BH
HH
F512
F513
F514
AX
AA
AY
BY
BA
DA
F515
F516
F517
F518
F519
F519
AK
AP
BP
BF
DP
HSH
FSH
F520
F520
F521
F523
F522
F524
F525
A5
A7
B5
HFTH
C/S
F526
F527
F528
F529
F530, 31
MA
MB
MC
F532
F532
F532
FLOATING
SHAFT
COUPLINGS
PAGES
SERIES
MICRO
COUPLINGS
DOUBLE
FLEX
F5-5
F5-6
DRIVEN EQUIPMENT
FANS
Centrifugal
Cooling Tower
FEEDERS
Apron
Belt
Disc
Reciprocating
Screw
FOOD INDUSTRY
Cereal Cookers
Dough Mixers
Meat Grinders
Slicers
LUMBER INDUSTRY
Barkers-Drum Type
Edger Feeders
Live Rolls
Log Haul
Off Bearing Rolls
Planers
Slab Conveyors
Sorting Table
Trimmer Feed
MACHINE TOOLS
Bending Roll
Plate Planer
Spindle Drives
Table/Axis Drives
Tapping Machines
PAPER MILLS
Beater & Pulper
Bleacher
Calendars
Converting Machines
S.F.
1.75
2.00
1.75
1.75
1.25
2.00
2.00
1.50
1.50
1.75
1.50
1.50
1.50
1.00
2.00
2.25
1.75
1.50
1.25
1.75
1.50
1.50
1.75
1.50
1.25
1.50
1.25
1.25
1.25
1.50
1.50
STEADY
MOTOR OR
TURBINE
DRIVEN
MODERATE
MOTOR OR
TURBINE
DRIVEN
MEDIUM
MOTOR OR
TURBINE
DRIVEN
HEAVY-HIGH
TQ. MOTOR
OR ENGINE
DRIVEN
EXTRA
HEAVY
ENGINE
DRIVEN
EXTREMELY
HEAVY
ENGINE
DRIVEN
SOFT
START
WITH
STEADY
LOAD
AVERAGE
STARTING
LOADS AND
SLIGHT
TORQUE
VARIATIONS
ABOVE
AVERAGE
STARTING
LOADS AND
MODERATE
LOAD
VARIATIONS
HIGH
STARTING
TORQUES
AND
MEDIUM TO
HEAVY
LOAD
VARIATIONS
MILD SHOCK
LOADING
ENGINES.
DRIVING
SMOOTH
LOADS.
EXTREME
RELIABILITY
HEAVY
SHOCK
LOADING
OR LIGHT
REVERSING
EXTREME
SHOCK
LOADING.
FREQUENT
WIDE
TORQUE
VARIATIONS
.
1.5
2.0
3.25
4.0
TYPE/SIZE
RATED MAX
TORQUE RPM
LB*IN
01
9
02
17
03
35
04
87
300
A SERIES 05
4 BOLT
10
800
15
1,575
20
2,200
25
3,800
30
6,930
35
11,340
40
18,270
45
30,240
3,050
B SERIES 33
6 BOLT
38
6,860
43
13,500
48
18,400
53
24,000
58
41,000
63
48,000
68
72,000
73
125,000
78
233,000
9,500
D SERIES 22
8 BOLT
26
16,000
31
24,000
35
44,000
37
60,000
42
73,000
45
99,000
50
128,000
55
189,000
60
261,000
70
415,000
75
533,000
80
685,000
85
829,000
92 1,040,000
105 1,250,000
160 2,000,000
MICRO
4 BOLT
20,000
20,000
20,000
20,000
8,500
7,500
6,700
6,200
5,500
5,000
4,400
4,000
3,700
17,400
14,300
12,700
11,000
10,700
9,475
8,590
7,800
6,740
5,600
3,800
3,300
2,800
2,600
2,500
2,400
2,250
2,000
1,800
1,600
1,400
1,300
1,200
1,100
1,000
1,000
900
O.D.
MAX
BORE
1.0
SERVICE FACTOR
2.5
3.0
1.02
1.26
1.65
2.24
2.65
3.19
3.65
4.08
4.95
5.63
6.63
7.64
8.43
4.69
5.87
6.7
7.5
7.87
9
10
10.75
12.5
15.05
6.00
6.88
8.13
9.13
10.06
11.00
11.88
13.44
15.00
16.75
18.94
20.63
22.38
23.75
25.75
29.25
33.50
0.38
0.59
0.79
0.79
0.87
1.25
1.37
1.62
2.00
2.37
2.87
3.25
3.75
2.50
3.25
3.75
4.38
4.50
5.13
5.50
6.00
6.50
7.50
2.25
2.63
3.13
3.63
3.75
4.50
4.75
5.50
6.25
7.12
7.87
8.75
9.12
9.62
11.00
12.00
17.00
0.01
0.03
0.06
0.14
0.48
1.27
2.50
3.49
6.03
11.00
18.00
29.00
48.00
4.84
10.89
21.43
29.21
38.10
65.08
76.19
114.29
198.41
369.84
15.08
25.40
38.10
69.84
95.24
115.87
157.14
203.17
300.00
414.29
658.73
846.03
1,087.30
1,315.87
1,650.79
1,984.13
3,174.60
0.01
0.02
0.04
0.09
0.32
0.85
1.67
2.33
4.02
7.33
12.00
19.33
32.00
3.23
7.26
14.29
19.47
25.40
43.39
50.79
76.19
132.28
246.56
10.05
16.93
25.40
46.56
63.49
77.25
104.76
135.45
200.00
276.19
439.15
564.02
724.87
877.25
1,100.53
1,322.75
2,116.40
0.01
0.01
0.03
0.07
0.24
0.63
1.25
1.75
3.02
5.50
9.00
14.50
24.00
2.42
5.44
10.71
14.60
19.05
32.54
38.10
57.14
99.21
184.92
7.54
12.70
19.05
34.92
47.62
57.94
78.57
101.59
150.00
207.14
329.37
423.02
543.65
657.94
825.40
992.06
1,587.30
0.19
0.51
1.00
1.40
2.41
4.40
7.20
11.60
19.20
1.94
4.36
8.57
11.68
15.24
26.03
30.48
45.71
79.37
147.94
6.03
10.16
15.24
27.94
38.10
46.35
62.86
81.27
120.00
165.71
263.49
338.41
434.92
526.35
660.32
793.65
1,269.84
NOT RECOMMENDED
FOR THESE
APPLICATIONS
1.61
3.63
7.14
9.74
12.70
21.69
25.40
38.10
66.14
123.28
5.03
8.47
12.70
23.28
31.75
38.62
52.38
67.72
100.00
138.10
219.58
282.01
362.43
438.62
550.26
661.38
1,058.20
1.49
3.35
6.59
8.99
11.72
20.02
23.44
35.16
61.05
113.80
4.64
7.81
11.72
21.49
29.30
35.65
48.35
62.52
92.31
127.47
202.69
260.32
334.55
404.88
507.94
610.50
976.80
3.77
6.35
9.52
17.46
23.81
28.97
39.29
50.79
75.00
103.57
164.68
211.51
271.83
328.97
412.70
496.03
793.65
F5-7
SIZE
05
10
15
20
25
30
35
40
45
MAX
BORE
0.87
1.25
1.37
1.62
2.00
2.38
2.88
3.25
3.75
A
2.65
3.19
3.65
4.08
4.95
5.63
6.63
7.64
8.43
B
0.25
0.30
0.35
0.35
0.45
0.55
0.55
0.65
0.65
F
1.00
1.00
1.13
1.32
1.62
1.88
2.25
2.50
3.00
H
1.30
1.30
2.00
2.40
2.80
3.30
4.15
4.65
5.40
J
0.38
0.38
0.41
0.50
0.63
0.69
0.88
0.94
1.20
STD SET
SCREW SIZE
10-24 UNC
1/4-20 UNC
1/4-20 UNC
1/4-20 UNC
5/16-18 UNC
5/16-18 UNC
1/2-13 UNC
1/2-13 UNC
1/2-13 UNC
SIZE
05
10
15
20
25
30
35
40
45
MAX
BORE
1.13
1.63
1.88
2.13
2.38
2.88
3.75
4.00
4.63
A
2.65
3.19
3.65
4.08
4.95
5.63
6.63
7.64
8.43
B
0.25
0.30
0.35
0.35
0.45
0.55
0.55
0.65
0.65
F
1.00
1.00
1.13
1.32
1.62
1.88
2.25
2.50
3.00
H
1.88
2.37
2.69
3.13
3.75
4.25
5.25
6.02
6.75
J
0.38
0.38
0.41
0.50
0.63
0.69
0.88
0.94
1.20
QD BORED HUBS
CPLG
SIZE
15
20
25
30
35
40
1.17
1.17
1.50
2.06
2.19
2.38
1.00
1.00
1.25
1.81
1.87
2.06
.56
.56
.75
1.25
1.25
1.37
2.00
2.40
2.80
3.30
4.15
4.65
BOLT
SIZE
UNC
#10
#10
1/4
1/4
5/16
3/8
CPLG
SIZE
BUSH
SIZE
15
20
25
30
35
40
N/A
1108
1215
1310
2012
2525
REGULAR MOUNT
BUSH
MAX
TQ
BORE
LB*IN
...
...
1300
1.12
3550
1.25
3850
1.37
7150
2.00
11300
2.50
BUSH
SIZE
...
0.87
1.50
1.00
1.25
2.50
1108
1215
1310
1615
2517
2525
STD SET
SCREW SIZE
10-24 UNC
1/4-20 UNC
1/4-20 UNC
1/4-20 UNC
5/16-18 UNC
5/16-18 UNC
1/2-13 UNC
1/2-13 UNC
1/2-13 UNC
REVERSE MOUNT
BUSH
MAX
TQ
BORE
LB*IN
1300
1.12
3550
1.25
3850
1.37
4300
1.62
11600
2.50
11300
2.50
SIZE
MAX BORE
AC
AD
SCREW SIZE
05
1.00
0.87
2.65
1.13
.50
2.06
1/4-20 UNC
10
1.00
1.50
1.00
1.75
1.31
2.12
2.13
2.50
0.87
1.25
0.87
1.37
1.00
1.62
1.62
1.87
3.19
1.18
1.36
1.27
1.46
1.32
1.52
1.62
1.86
.50
.69
.50
.69
.55
.75
.64
.88
2.06
2.75
2.06
3.00
2.38
3.50
3.50
4.00
1/4-20 UNC
5/16-18 UNC
1/4-20 UNC
5/16-18 UNC
1/4-20 UNC
3/8-16 UNC
5/16-18 UNC
3/8-16 UNC
15
20
25
3.65
4.08
4.95
NOTE: AC and AL Hubs do not carry full torque capacity. Please consult engineering.
F5-8
SIZE
05
10
15
20
25
HUB
TYPE
AJ
AZ
AJ
AZ
AJ
AZ
AJ
AZ
AJ
AZ
BORE SIZE-mm
MIN
MAX
6
13
14
19
12
18
19
30
12
22
24
35
22
30
32
42
22
32
35
50
B
1.00
1.00
1.00
1.00
1.13
1.13
1.32
1.32
1.63
1.63
F
1.32
1.42
1.42
1.42
1.55
1.55
1.78
1.83
2.05
2.23
G
.32
.42
.42
.42
.42
.42
.42
.51
.42
.60
F
0.87
1.50
1.00
1.50
1.75
2.50
SCREW SIZE
10-32 UNF
1/4-28 UNF
1/4-28 UNF
1/4-28 UNF
1/4-28 UNF
1/4-28 UNF
1/4-28 UNF
5/16-24 UNF
1/4-28 UNF
3/8-24 UNF
SIZE
33
38
43
48
53
58
63
68
73
78
MAX
BORE
2.25
3.00
3.25
3.75
3.88
4.25
4.88
5.00
5.25
6.50
A
4.69
5.87
6.70
7.50
7.87
9.00
10.00
10.75
12.50
15.05
B
0.30
0.35
0.42
0.40
0.55
0.65
0.65
0.75
1.00
1.15
F
1.75
2.25
2.50
2.75
2.88
3.25
3.38
3.75
5.13
6.38
H
3.14
4.13
4.63
5.40
5.65
6.22
7.14
7.33
7.80
9.50
J
0.88
1.13
1.25
1.50
1.44
1.63
1.69
1.88
2.50
3.12
SIZE
22
26
31
35
37
42
45
50
55
60
70
75
80
85
92
OPTIONAL SET
SCREW SIZE
1/4-20 UNC
3/8-16 UNC
3/8-16 UNC
1/2-13 UNC
1/2-13 UNC
1/2-13 UNC
3/4-10 UNC
3/4-10 UNC
3/4-10 UNC
3/4-10 UNC
MAX BORE
IRON STEEL
2.25
2.62
3.12
3.62
3.75
4.25
4.50
4.50
4.75
5.12
5.50
5.62
6.25
6.50
7.12
7.00
7.87
7.75
8.75
8.00
9.12
8.50
9.62
10.00
11.00
A
6.00
6.87
8.12
9.12
10.06
11.00
11.87
13.43
15.00
16.75
18.93
20.62
22.37
23.75
25.75
B
0.53
0.62
0.69
0.88
0.88
1.00
1.13
1.25
1.25
1.44
1.75
1.75
2.09
2.13
2.62
F
2.50
2.88
3.38
3.75
4.00
4.25
4.50
5.00
5.50
6.25
7.00
7.25
7.75
8.25
9.00
H
3.88
4.50
5.50
6.12
6.50
7.00
7.43
8.38
9.50
10.50
11.75
13.00
13.75
14.50
15.87
4 BOLT DISCS
6 BOLT DISCS
8 BOLT DISCS
SIZE
WIDTH
I.D.
B.C.
DIA
1-7/8
2-3/8
2-5/8
CHORD
1
1-3/16
1-1/4
HOLE
DIA
1/4
1/4
5/16
1-5/16
1-5/8
1-7/8
DISC SET
THICKNESS
0.06
0.09
0.12
5
10
15
1-13/16
2-3/16
2-9/16
20
25
30
2-13/16
3-9/16
4
1-5/8
1-3/4
2-1/16
5/16
7/16
1/2
3-1/8
3-3/4
4-1/4
2-3/16
2-5/8
3
0.14
0.15
0.18
35
40
45
4-3/4
5-1/2
6-1/16
2-3/4
3
3-1/2
1/2
5/8
5/8
5-1/4
6
6-3/4
3-3/4
4-1/4
4-3/4
0.28
0.30
0.40
50
55
7
7-3/4
4
4-1/4
3/4
1
7-3/4
8-1/2
5-1/2
6
0.43
0.51
SIZE
WIDTH
I.D.
3-3/4
4-13/16
5-11/6
2-3/4
3-9/16
3-15/16
B.C.
DIA
3-3/4
4-7/8
5-9/16
CHORD
33
38
43
HOLE
DIA
1/4
5/16
7/16
1-7/8
2-7/16
2-7/8
DISC SET
THICKNESS
0.10
0.13
0.16
48
53
58
6-3/8
6-3/4
7-3/4
4-5/8
4-3/4
5-1/4
7/16
1/2
5/8
6-3/8
6-5/8
7-7/16
3-3/16
3-5/16
3-3/4
0.19
0.24
0.25
63
68
8-1/2
9-1/4
6
6-1/4
5/8
3/4
8-3/8
9-15/16
4-3/16
5
0.30
0.34
SIZE
WIDTH
I.D.
5-5/8
6-9/16
7-3/4
3-7/8
4-7/16
5-1/4
B.C.
DIA
4-3/4
5-1/2
6-1/2
CHORD
22
26
31
HOLE
DIA
5/16
13/32
15/32
1-13/16
2-1/8
2-1/2
DISC SET
THICKNESS
0.17
0.23
0.25
35
37
42
8-5/8
9-5/8
10-1/2
5-3/4
6-5/16
6-3/4
17/32
5/8
11/16
7-1/4
8
8-5/8
2-3/4
3-1/16
3-5/16
0.29
0.31
0.31
45
50
55
11-1/4
12-13/16
14-3/8
7-1/4
8-1/2
9
3/4
7/8
1
9-1/4
10-1/2
11-3/4
3-1/2
4
4-1/2
0.37
0.46
0.54
60
70
75
15-15/16
18-/8
19-3/4
9-15/16
11-1/8
12
1-1/8
1-5/16
1-7/16
13
14-3/4
16
5
5-5/8
6-1/8
0.59
0.78
0.80
80
85
92
21-7/16
22-7/8
24-7/8
13-1/8
14
15
1-9/16
1-3/4
1-7/8
17-3/8
18-1/2
20
6-5/8
7-1/8
7-5/8
0.81
0.87
1.00
F5-9
ENGINEERING STANDARDS
FORM - FLEX COUPLINGS
INDUSTRY STANDARDS REFERENCED
AGMA 9002-A86BORES AND KEYWAYS FOR FLEXIBLE COUPLINGS
AGMA 9000-C90FLEXIBLE COUPLINGS POTENTIAL UNBALANCED CLASSIFICATION
AGMA 514.02LOAD CLASSIFICATION AND SERVICE FACTORS FOR FLEXIBLE COUPLINGS
API610CENTRIFUGAL PUMPS FOR GENERAL REFINERY SERVICE, 7th EditionBF and BP series meet the requirements of
API610, 7th Edition when supplied with interference fit bores. Other coupling series can be altered to comply with API610.
NEMA MG1-14.37 AND MG1-21.81All Form-Flex metal disc couplings meet these standards without limited end float devices
Certain tables and data in this catalog were extracted from the reference AGMA standards with the permission of the publisher, the American
Gear Manufacturers Associations, 1901 North Meyer Drive, Arlington, VA 22209.
MATERIAL CLASSES APPLICABLE TO 4 AND 6 BOLT DESIGNS
CLASS A
Mild steel hubs and spacer, alloy steel hardware, 300 series stainless steel flex discs.
CLASS B
Zinc plated mild steel hubs and spacer, alloy steel hardware, 300 series stainless steel flex discs.
CLASS C
Zinc plated mild steel hubs and spacer, 300 series stainless steel hardware and flex discs.
CLASS E
All 300 series stainless steel construction.
DYNAMIC BALANCING RECOMMENDATIONS
Use this graph to determine the appropriate balance class based on
coupling weight and operating speed. The balance classes listed on
the graph are for equipment with average sensitivity to coupling
unbalance. The user should determine how sensitive the equipment
train is to coupling unbalance. Use one balance class higher if your
system has higher than average sensitivity to unbalance. Use one
balance class lower if your system has lower than average sensitivity to
unbalance. Use this guide to check your coupling selection against the
recommended balance class for your operating conditions.
The following factors should be considered when determining a machines
sensitivity to coupling unbalance.
1) Shaft End Deflection: Machines having flexible shaft extensions are
relatively sensitive to coupling unbalance.
2) Bearing Load Due to Coupling Weight Relative to Total Bearing Load:
Machines having lightly loaded bearings, bearings that are primarily
loaded by the weight of the coupling or other overhung weight are
relatively sensitive to coupling unbalance.
3) Bearing, Bearing Support and Foundation Flexibility: Machines
or systems with flexible foundations for supports for the rotating
elements are relatively sensitive to coupling unbalance.
4) System Natural Frequencies: Machines operating at or near natural
frequencies are sensitive to coupling unbalance.
5) Machine Separation: System having widely separated machines are
relatively sensitive to coupling unbalance.
6) Shaft Extension Relative to Bearing Span: Machines having a short
bearing span relative to their shaft extensions are sensitive to
static unbalance.
HOW FORM-FLEX COUPLINGS ACCOMMODATE MISALIGNMENT
Double flexing metal disc couplings may be used to accommodate angular,
parallel and axial misalignment. Single flexing couplings may only be used to
accommodate angular and axial misalignment. A metal disc type coupling uses
a double hinge effect through two flexible discs and the spacer to compensate
for parallel offset misalignment between shafts. Parallel misalignment
imposes the same angular deflection (A) on each flex disc. Angular
misalignment of either connected shaft, (B), creates additional angular
deflections which are added to the angular offset due to parallel misalignment.
The total misalignment angle, (C), at the flex disc is equal to the angular offset
due to parallel misalignment (A) plus the angular offset due to angular
misalignment (B). The maximum misalignment angle (C) should never exceed
the rated misalignment capacity of the coupling type being used. Machinery
equipment changes in actual operation and over the life of the equipment. We
recommend that the machinery misalignment be set as close to zero as
possible when a coupling is installed. We recommend keeping the measured
misalignment below 25% of the rated misalignment capacity of the
coupling type used when the machinery is installed and aligned. The remaining
coupling misalignment capacity will then be available to accommodate additional
misalignment caused by foundation shifts, vibrations, thermal growth or other causes.
F5-10
ENGINEERING STANDARDS
FORM-FLEX COUPLINGS
PRODUCT FEATURES AND OPTIONS
FEATURE
AR, AK, AP
AX, AY
CLEARANCE
STANDARD
OPTIONAL
BH, BP, BY
BF
BA, DA*
A5, A7
B5
HFTH
HH, HSH, FSH
DP*
STANDARD BORE FIT
INTERFERENCE
CLEARANCE
INTERFERENCE
SET SCREWS
OPTIONAL
STANDARD
OPTIONAL
PULLER HOLES
STANDARD
OPTIONAL
STANDARD
OPTIONAL
STANDARD FLEX DISCS
300 SERIES STAINLESS STEEL*
ALLOY STEEL
BALANCE CLASS
AGMA 7
AGMA 8
AGMA 9
AGMA 7
N/A
N/A
DYNAMIC BALANCE
OPTIONAL
PER TBW COMMERCIAL STANDARD
N/A
*Alloy steel flex disc is standard for DA and DP series. Stainless steel is optional.
SIZE
BORE TOLERANCE
12
58
34
78
15/16
KEYWAY
SIZE
1/8 X 1/16
3/16 X 3/32
3/16 X 3/32
3/16 X 3/32
1/4 X 1/8
CLEARANCE FIT
.500/.501
.625/.626
.750/.751
.875/.876
.9375/.9385
INTERFERENCE FIT
...
...
.7490/.7495
.8740/.8745
.9365/.9370
1
1-1/8
1-3/16
1-1/4
1-3/8
1-7/16
1-1/2
1-5/8
1-3/4
1-7/8
1-15/16
1
118
1316
114
138
1716
112
158
134
178
11516
1/4 X 1/8
1/4 X 1/8
1/4 X 1/8
1/4 X 1/8
5/16 X 5/32
3/8 X 3/16
3/8 X 3/16
3/8 X 3/16
3/8 X 3/16
1/2 X 1/4
1/2 X 1/4
1.000/1.001
1.125/1.126
1.1875/1.1885
1.250/1.251
1.375/1.376
1.4375/1.4385
1.500/1.501
1.625/1.626
1.750/1.751
1.875/1.876
1.9375/1.9385
.9990/.9995
1.1240/1.1245
1.1865/1.1870
1.2490/1.2495
1.3740/1.3745
1.4365/1.4370
1.4990/1.4995
1.623/1.624
1.748/1.749
1.873/1.874
1.9355/1.9365
2
2-1/8
2-1/4
2-3/8
2-7/16
2-1/2
2-5/8
2-3/4
2-7/8
2-15/16
2
218
214
238
2716
212
258
234
278
21516
1/2 X 1/4
1/2 X 1/4
1/2 X 1/4
5/8 X 5/16
5/8 X 5/16
5/8 X 5/16
5/8 X 5/16
5/8 X 5/16
3/4 X 3/8
3/4 X 3/8
2.000/2.001
2.1250/2.1265
2.2500/2.2515
2.3750/2.3765
2.4375/2.4390
2.5000/2.5015
2.6250/2.6265
2.7500/2.7515
2.8750/2.8765
2.9375/2.9390
1.998/1.999
2.123/2.124
2.248/2.249
2.373/2.374
2.4355/2.4365
2.498/2.499
2.623/2.624
2.748/2.749
2.873/2.874
2.9355/2.9365
3
3-1/4
3-3/8
3-1/2
3-5/8
3-3/4
3
314
338
312
358
334
3/4 X 3/8
3/4 X 3/8
7/8 X 7/16
7/8 X 7/16
7/8 X 7/16
7/8 X 7/16
3.000/3.0015
3.2500/3.2515
3.3750/3.3765
3.5000/3.5015
3.6250/3.6265
3.7500/3.7515
2.998/2.999
3.2470/3.2485
3.3720/3.3735
3.4970/3.4985
3.6220/3.6235
3.7470/3.7485
4
4-1/4
4-1/2
4-3/4
4
414
412
434
1 X 1/2
1 X 1/2
1 X 1/2
1-1/4 X 5/8
4.0000/4.0015
4.2500/4.2515
4.5000/4.5015
4.7500/4.7515
3.9970.3.9985
4.2465/4.2480
4.4965/4.4980
4.7465/4.7480
5
5-1/4
5-1/2
5-3/4
5
514
512
534
1-1/4
1-1/4
1-1/4
1-1/2
X
X
X
X
5/8
5/8
5/8
3/4
.
.
.
.
.
.
.
.
.
.
.
.
4.9965/4.9980
5.2460/5.2475
5.4960/5.4975
5.7460/5.7475
METRIC
SIZE
6
8
10
12
13
14
15
16
18
20
22
24
25
28
30
32
35
38
40
45
48
50
55
60
65
70
75
80
85
90
95
100
110
SIZE
CODE
6MM
8MM
10MM
12MM
13MM
14MM
15MM
16MM
18MM
20MM
22MM
24MM
25MM
28MM
30MM
32MM
35MM
38MM
40MM
45MM
48MM
50MM
55MM
60MM
65MM
70MM
75MM
80MM
85MM
90MM
95MM
100MM
110MM
KEYWAY
SIZE
2X1
2X1
3 X 1.4
4 X 1.8
5 X 2.3
5 X 2.3
5 X 2.3
5 X 2.3
6 X 2.8
6 X 2.8
6 X 2.8
8 X 3.3
8 X 3.3
8 X 3.3
8 X 3.3
10 X 3.3
10 X 3.3
10 X 3.3
12 X 3.3
14 X 3.8
14 X 3.8
14 X 3.8
16 X 4.3
18 X 4.4
18 X 4.4
20 X 4.9
20 X 4.9
22 X 5.4
22 X 5.4
25 X 5.4
25 X 5.4
28 X 6.4
28 X 6.4
BORE TOLERANCE
CLEARANCE FIT
.236/.237
.315/.316
.394/.395
.4725/.4735
.512/.513
.551/.552
.591/.592
.630/.631
.709/.710
.7875/.7885
.866/.867
.945/.946
.984/.985
1.1025/1.1035
1.181/1.182
1.260/1.261
1.378/1.379
1.496/1.497
1.575/1.576
1.772/1.773
1.890/1.891
1.969/1.970
2.1655/2.1670
2.3620/2.3635
2.5590/2.5605
2.7560/2.7575
2.9530/2.9545
3.1500/3.1515
3.3465/3.3480
3.5435/3.5450
3.7400/3.7415
3.9370/3.9385
4.3310/4.3325
KEYWAY TOLERANCES
WIDTH
ENGLISH
METRIC
HEIGHT
BORE < = 3.375
AT SIDE
OF KW
BORE > 3.375
+ .002/ 0.000
+ .001/ 0.000
+ .015/ 0.000
+ .020/ 0.000
F511
SIZE
05
10
15
20
25
30
35
40
SIZE
05-45
05-45
15-40
05-25
05-25
MAX BORE
AJ
AZ
0.87
1.13
1.25
1.63
1.37
1.88
1.62
2.13
2.00
2.38
2.38
2.88
2.88
3.75
3.25
4.00
MATERIAL
CLASSES
CLASS
SIZE
A
05-45
B
05-45
C
15-45
E
15-45
SEE PAGE F54
A
2.65
3.19
3.65
4.08
4.95
5.63
6.63
7.64
DIMENSIONS IN INCHES*
D
B
DBSE
2.24
0.24
2.27
0.27
2.58
0.32
2.98
0.34
3.69
0.45
4.23
0.47
5.05
0.55
5.60
0.60
1.00
1.00
1.13
1.32
1.62
1.88
2.25
2.50
1.30
1.80
2.00
2.40
2.80
3.30
4.15
4.65
0.54
0.59
0.88
0.79
1.00
1.14
0.97
1.30
FREE END
FLOAT
+/- INCH
0.015
0.020
0.021
0.027
0.030
0.032
0.042
0.050
SIZE
05
10
15
20
25
30
35
40
HP PER
100 RPM
1.0 S.F
0.48
1.27
2.50
3.49
6.03
11.00
18.00
29.00
RATED TORQUE
( lb. in.)
300
800
1,575
2,200
3,800
6,930
11,340
18,270
PEAK O/L
TORQUE
(lb. in.)
600
1,600
3,150
4,400
7,600
13,860
22,680
36,540
AGMA 7
MAX
RPM
8,500
7,500
6,700
6,200
5,500
5,000
4,400
4,000
MAX
RADIAL
LOAD (lbs.)
34
56
125
183
275
400
600
850
WEIGHT
(lbs.)
WR2
(lb. in.2)
1.24
1.96
2.98
4.07
7.01
10.8
17.2
25.6
0.96
2.35
4.62
7.48
20.4
41.5
88.3
178.
NOTE:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR AJ HUBS AT MAXIMUM BORE SIZE.
F512
TQ/RAD
X106
(lb. in./rad)
0.28
0.84
1.47
2.11
3.62
5.91
11.0
17.0
FLEX
ASSY
PART #
AxxRKA
AxxRKA
AxxRKE
AxxRKE
xx = SIZE
SIZE
33
38
43
48
53
58
63
68
MAX
BORE
2.25
3.00
3.25
3.75
3.88
4.25
4.88
5.00
DIMENSIONS IN INCHES
D
A
B
DBSE
4.69
5.87
6.70
7.50
7.87
9.00
10.00
10.75
3.79
4.84
5.47
6.00
6.28
7.06
7.36
8.35
0.29
0.34
0.47
0.50
0.52
0.56
0.60
0.85
1.75
2.25
2.50
2.75
2.88
3.25
3.38
3.75
3.14
4.13
4.63
5.40
5.65
6.22
7.14
7.33
MATERIAL
CLASSES
CLASS
SIZE
A
33-78
B
33-78
C
38-63
E
MTO 38-63
SEE PAGE F54
FLEX
ASSY
PART #
BOxxRKA
BOxxRKA
BOxxRKE
BOxxRKE
xx = SIZE
SIZE
33
38
43
48
53
58
63
68
HP PER
100 RPM
1.0 S.F
4.84
10.08
19.84
26.98
38.10
53.97
76.19
114.29
RATED TORQUE
(lb. in.)
3,050
6,350
12,500
17,000
24,000
34,000
48,000
72,000
PEAK O/L
TORQUE
(lb. in.)
6,100
12,500
25,000
34,000
48,000
68,000
96,000
144,000
AGMA 8
MAX
RPM
8,400
7,500
6,800
6,500
6,000
5,500
5,200
4,800
MAX
RADIAL
LOAD (lbs.)
150
240
420
655
720
930
1,125
1,530
WEIGHT
(lbs.)
WR2
(lb. in.2)
5.76
11.4
17.3
25.2
29.8
45.4
58.4
73.4
14.5
46.6
91.7
171
226
443
715
984
TQ/RAD
FREE END
FLOAT
X106
(lb. in./rad)
+/- inch
4.57
0.03
9.41
0.04
17.8
0.05
25.5
0.06
29.8
0.06
50.0
0.06
76.6
0.07
96.7
0.07
NOTE:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR BH HUBS AT MAXIMUM BORE SIZE.
F513
SIZE
22
26
31
35
37
42
45
50
55
60
70
75
80
85
92
105
160
SIZE
22
26
31
35
37
42
45
50
55
60
70
75
80
85
92
105
160
MAX BORE
IRON
STEEL
2.25
2.62
3.12
3.63
3.62
4.00
3.75
4.50
4.25
4.75
4.50
5.13
5.12
5.50
5.62
6.25
6.50
7.12
7.00
7.87
7.75
8.75
8.00
9.12
8.50
9.62
10.00
11.00
10.50
12.00
16.00
17.00
HP PER
100 RPM
1.0S.F
15.08
25.40
38.10
69.84
95.24
115.87
157.14
203.17
300.00
414.29
658.73
846.03
1,087.30
1,315.87
1,650.79
1,984.13
3,174.60
DIMENSIONS IN INCHES
D
A (2)
B
DBSE
6.00
6.87
8.12
9.12
10.06
11.00
11.87
13.43
15.00
16.75
18.93
20.62
22.37
23.75
25.75
29.25
33.50
RATED TORQUE
(lb. in.)
9,500
16,000
24,000
44,000
60,000
73,000
99,000
128,000
189,000
261,000
415,000
533,000
685,000
829,000
1,040,000
1,250,000
2,000,000
5.43
6.29
7.38
8.16
8.81
9.31
9.87
11.06
12.25
13.84
15.50
16.05
17.06
18.12
19.75
22.75
26.25
PEAK O/L
TORQUE
(lb. in.)
14.250
24,000
36,000
66,000
90,000
109,500
148,500
192,000
283,500
391,500
622,500
799,500
1,027,500
1,243,500
1,560,000
1,875,000
3,000,000
0.43
0.53
0.62
0.66
0.81
0.81
0.87
1.06
1.25
1.34
1.50
1.55
1.56
1.62
1.75
1.75
2.25
AGMA 8
MAX
RPM
3,800
3,300
2,800
2,600
2,500
2,400
2,250
2,000
1,800
1,600
1,400
1,300
1,200
1,100
1,000
1,000
900
2.50
2.88
3.38
3.75
4.00
4.25
4.50
5.00
5.50
6.25
7.00
7.25
7.75
8.25
9.00
10.50
12.00
3.87
4.50
5.50
6.12
6.50
7.00
7.43
9.50
9.50
10.50
11.75
13.00
13.75
14.50
15.87
20.00
24.00
MAX
RADIAL
LOAD (lbs.)
338
570
700
930
1,170
1,300
1,700
2,250
3,200
4,000
6,100
6,900
7,500
8,700
11,100
8,460
11,300
HUB OPTIONS
HUB TYPE
SIZE
C.I.
26-160
STL
31-160
SEE PAGE F59
WEIGHT
(lbs.)
WR2
(lb. in.2)
17
26
43
61
77
95
115
163
228
328
451
588
732
840
1,160
1,780
2,310
62
129
304
557
820
1,250
1,810
3,290
5,570
10,300
18,200
27,400
42,100
54,700
89,400
160,000
325,000
NOTE:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR CAST IRON HUBS AT MAXIMUM BORE SIZE.
2) HUB FLANGE O.D. MAY VARY WITH STEEL HUBS.
F514
TQ/RAD
FREE END
X10 6
FLOAT
(lb. in./rad)
+/- inch
12.7
0.018
22.1
0.022
36.4
0.026
52.8
0.028
69.6
0.031
84
0.034
106
0.036
147
0.041
243
0.046
349
0.051
482
0.058
682
0.062
779
0.068
911
0.070
1220
0.078
3200
0.085
5140
0.125
RATED MISALIGNMENT:
1.0 DEG/DISC
AD HUB
SHOWN
HUB OPTIONS
HUB TYPE
AJ - STANDARD
AZ - OVERSIZE
QD BUSHING MOUNT
AC/AD CLAMP
AL LOCK ELEMENT
SEE PAGE F58
SIZE
05
10
15
20
25
30
35
40
SIZE
05-45
05-45
15-40
05-25
05-25
MAX BORE
AJ
AZ
0.87
1.13
1.25
1.63
1.37
1.88
1.62
2.13
2.00
2.38
2.38
2.88
2.88
3.75
3.25
4.00
MATERIAL
CLASSES
CLASS
SIZE
A
05-45
B
05-45
C
N/A
E
N/A
SEE PAGE F54
2.65
3.19
3.65
4.08
4.95
5.63
6.63
7.64
3.34
3.40
3.80
4.22
5.36
6.30
7.17
8.30
DIMENSIONS IN INCHES*
DBSE
F
Dmin
Dmax
0.38
1.34
1.00
0.44
1.40
1.00
0.63
1.54
1.13
0.63
1.58
1.32
0.75
2.12
1.62
1.00
2.54
1.88
1.13
2.67
2.25
1.13
3.30
2.50
SPACER
ASSEMBLY
PART #
AXxxSAA
AXxxSAB
N/A
N/A
xx = SIZE
0.48
0.48
0.44
0.48
0.69
0.77
0.77
1.08
1.30
1.30
2.00
2.40
2.80
3.30
4.15
4.65
1.68
1.79
1.85
1.66
2.39
3.18
2.81
4.03
DISC
I.D.**
1.00
1.17
1.28
1.65
1.78
2.01
2.71
3.00
SIZE
05
10
15
20
25
30
35
40
HP PER
100 RPM
1.0 S.F
0.48
1.27
2.50
3.49
6.03
11.00
18.00
29.00
RATED TORQUE
(lb. in.)
300
800
1,575
2,200
3,800
6,930
11,340
18,270
PEAK O/L
TORQUE
(lb. in.)
450
1,200
2,363
3,300
5,700
10,395
17,010
27,405
AGMA 7
MAX
RPM
8,500
7,500
6,700
6,200
5,500
5,000
4,400
4,000
WEIGHT
(lbs.)
WR2
(lb. in.2)
1.63
2.48
3.84
5.10
9.13
13.8
21.1
32.0
1.26
2.90
5.80
9.16
26.1
51.7
108
222
TQ/RAD
X10 6
(lb. in./rad)
0.04
0.06
0.21
0.25
0.56
0.79
1.48
1.68
FREE END
FLOAT
+/- inch
0.030
0.040
0.042
0.055
0.060
0.065
0.085
0.100
NOTES
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR AJ HUBS AT MAXIMUM BORE SIZE.
F515
RATED MISALIGNMENT:
1.0 DEG/DISC
HUB OPTIONS
HUB TYPE
AJ - STANDARD
AZ - OVERSIZE
QD BUSHING MOUNT
AC/AD CLAMP
AL LOCK ELEMENT
SEE PAGE F58
SIZE
05
10
15
20
25
30
35
40
SIZE
05-45
05-45
15-40
05-25
05-25
MAX BORE
AJ
AZ
0.87
1.13
1.25
1.63
1.37
1.88
1.62
2.13
2.00
2.38
2.38
2.88
2.88
3.75
3.25
4.00
MATERIAL
CLASSES
CLASS
SIZE
A
05-45
B
05-45
C
15-45
E
N/A
SEE PAGE F54
2.65
3.19
3.65
4.08
4.95
5.63
6.63
7.64
3.23
3.73
3.82
4.38
5.26
6.24
6.91
7.70
DIMENSIONS IN INCHES*
DBSE
F
Dmin
Dmax
0.25
1.23
1.00
0.25
1.73
1.00
0.31
1.56
1.13
0.41
1.74
1.32
0.41
2.02
1.62
0.56
2.48
1.88
0.66
2.41
2.25
0.75
2.70
2.50
0.24
0.27
0.32
0.34
0.45
0.47
0.55
0.60
1.30
1.80
2.00
2.40
2.80
3.30
4.15
4.65
0.54
0.56
0.88
0.79
1.00
1.14
0.97
1.30
SIZE
05
10
15
20
25
30
35
40
HP PER
100 RPM
1.0 S.F
0.48
1.27
2.50
3.49
6.03
11.00
18.00
29.00
RATED TORQUE
(lb. in.)
300
800
1,575
2,200
3,800
6,930
11,340
18,270
PEAK O/L
TORQUE
(lb. in.)
450
1,200
2,363
3,300
5,700
10,395
17,010
27,405
MAX
RPM
WEIGHT
(lbs.)
WR2
(lb. in.2)
3,600
3,500
3,450
3,350
3,200
3,000
2,800
2,650
1.76
2.77
4.24
5.48
9.81
15.0
22.4
34.3
1.40
3.35
6.66
10.2
29.4
59
121
250
TQ/RAD
X106
(lb. in./rad)
0.06
0.10
0.26
0.25
0.62
0.94
1.44
2.43
NOTES:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR AJ HUBS AT MAXIMUM BORE SIZE.
2) MAX RPM SHOWN BASED ON CAST IRON SPACER MATERIAL.
F516
SPACER
ASSEMBLY
PART #
AAxxSAA
AAxxSAB
AAxxSAC
N/A
xx = SIZE
FREE END
FLOAT
+/- inch
0.030
0.040
0.042
0.055
0.060
0.065
0.085
0.100
DISC
I.D.**
1.00
1.17
1.28
1.65
1.78
2.01
2.71
3.00
AL
HUB SHOWN
SIZE
05
10
15
20
25
SIZE
05-25
05-25
15-25
05-25
05-25
MAX BORE
AJ
AZ
0.87
1.13
1.25
1.63
1.37
1.88
1.62
2.13
2.00
2.38
MATERIAL
CLASSES
CLASS
SIZE
A
05-25
B
05-25
C
N/A
E
N/A
SEE PAGE F54
2.65
3.19
3.65
4.08
4.95
2.85
2.91
3.33
3.76
4.77
DIMENSIONS IN INCHES*
DBSE
Dmin
Dmax
0.49
0.85
0.50
0.91
0.56
1.07
0.56
1.12
0.87
1.53
1.00
1.00
1.13
1.32
1.62
0.24
0.27
0.32
0.34
0.45
1.30
1.80
2.00
2.40
2.80
SPACER
ASSEMBLY
PART #
AYxxSAA
AYxxSAB
N/A
N/A
xx = SIZE
DISC
I.D.**
1.00
1.17
1.28
1.65
1.78
SIZE
05
10
15
20
25
HP PER
100 RPM
1.0 S.F
0.48
1.27
2.50
3.49
6.03
RATED TORQUE
(lb. in.)
300
800
1,575
2,200
3,800
PEAK O/L
TORQUE
(lb. in.)
600
1,600
3,150
4,400
7,600
AGMA 7
MAX
RPM
8,500
7,500
6,700
6,200
5,500
WEIGHT
(lbs.)
1.64
2.68
4.23
5.49
9.78
WR2
(lb. in.2)
(lb. in./rad)
1.24
3.08
6.41
9.92
27.6
TQ/RAD
X106
0.13
0.35
0.64
0.83
1.56
FREE END
FLOAT
+/- inch
0.030
0.040
0.042
0.055
0.060
NOTE:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR AJ HUBS AT MAXIMUM BORE SIZE.
F517
SIZE
33
38
43
48
53
58
63
68
MAX BORE
BY inv BH ext
2.00
2.25
2.63
3.00
2.88
3.25
3.25
3.75
3.63
3.88
4.00
4.25
4.50
4.88
4.75
5.00
SIZE
33
38
43
48
53
58
63
68
A
4.69
5.87
6.70
7.50
7.87
9.00
10.00
10.75
B1
B2
B3
4.13
4.45
5.41
5.64
6.77
7.60
8.40
9.20
4.530
5.260
6.265
6.630
7.600
8.700
9.230
10.450
4.93
6.07
7.12
7.62
8.43
9.80
10.06
11.70
PEAK O/L
TORQUE
(lb. in.)
4,575
9,525
18,750
25,500
36,000
51,000
72,000
108,000
AGMA 8
MAX
RPM
8,400
7,500
6,800
6,500
6,000
5,500
5,200
4,800
DIMENSIONS IN INCHES
DBSE
C
D1
D2
1.350
0.43
0.930
1.440
0.57
1.070
1.645
0.81
1.465
1.760
0.76
1.440
2.050
1.01
1.840
2.150
1.20
2.250
2.550
1.20
2.250
2.500
1.60
2.900
WEIGHT
(lbs.)
WR2
(lb. in.2)
8.06
13.9
23.2
31.1
40.3
65.4
82.8
106
22.3
65.1
144
241
345
734
1150
1760
D3
1.43
1.57
2.12
2.12
2.67
3.30
3.30
4.20
Fe
Ji
1.85
1.94
2.30
2.44
2.88
3.20
3.60
3.80
1.75
2.25
2.50
2.75
2.88
3.25
3.38
3.75
3.14
4.13
4.63
5.40
5.65
6.22
7.14
7.33
1.46
1.61
2.51
2.34
2.93
4.40
4.00
5.28
TQ/RAD
FREE END
X106
FLOAT
(lb. in./rad)
+/- inch
0.94
0.060
2.98
0.084
4.99
0.090
5.42
0.108
9.10
0.108
15.4
0.118
25.8
0.140
37.4
0.144
NOTE:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR BY HUBS AT MAXIMUM BORE SIZE.
F518
Fi
Je
1.06
0.80
1.60
1.35
2.10
3.30
3.17
4.03
MATERIAL
SPACER
CLASSES
ASSEMBLY
CLASS SIZE
PART #
A
33-68 BYxxSAA
B
33-68 BYxxSAB
C
N/A
N/A
E
N/A
N/A
SEE PAGE F54 xx = SIZE
SIZE
BA33
BA38
BA43
DA31
DA35
DA37
DA42
DA45
DA50
DA55
DA60
DA70
SIZE
BA33
BA38
BA43
DA31
DA35
DA37
DA42
DA45
DA50
DA55
DA60
DA70
MAX
BORE
1.75
2.50
2.63
3.38
3.75
4.19
4.50
4.75
5.00
5.50
6.00
7.00
DIMENSIONS IN INCHES
D
A
B
DBSE
4.69
5.87
6.70
7.81
8.69
9.69
10.50
11.31
12.88
14.44
16.00
18.25
HP PER
100 RPM
1.0 S.F
6.29
13.10
25.79
38.10
54.13
81.11
114.76
130.48
196.83
300.00
390.48
549.21
3.88
4.38
5.00
5.87
6.81
7.37
8.19
9.31
9.75
11.00
12.38
14.38
0.12
0.12
0.12
0.19
0.25
0.25
0.25
0.31
0.31
0.38
0.38
0.38
RATED TORQUE
(lb. in.)
3,965
8,255
16,250
24,000
34,100
51,100
72,300
82,200
124,000
189,000
246,000
346,000
F
1.88
2.13
2.44
2.84
3.28
3.56
3.97
4.50
4.72
5.31
6.00
7.00
PEAK O/L
TORQUE
(lb. in.)
7,930
16,510
32,500
48,000
68,200
102,200
144,600
164,400
248,000
378,000
492,000
692,000
G
0.33
0.40
0.48
0.44
0.54
0.69
0.69
0.75
0.96
1.04
1.10
1.40
H
2.71
3.55
3.91
5.22
5.71
6.18
6.70
7.20
7.93
8.95
9.89
11.08
MAX RPM
UNBALANCED
BALANCED
4,200
3,800
3,700
3,000
2,800
2,500
2,300
2,200
2,000
1,900
1,800
1,700
7,000
6,300
6,000
5,000
4,500
4,000
3,700
3,400
3,300
2,800
2,500
2,500
WEIGHT
(lbs.)
WR2
(lb. in.2)
10.7
18.1
30.2
45.5
63.4
87
114
152
215
317
450
664
29.2
81.7
158
372
627
1,110
1,670
2,550
4,610
8,550
14,900
28,800
FREE END
FLOAT
+/- inch
0.060
0.084
0.090
0.052
0.056
0.062
0.067
0.072
0.082
0.092
0.102
0.115
NOTE:
1) WEIGHTS AND WR2 VALUES SHOWN ARE AT MAXIMUM BORE SIZE.
F519
SPACER 4 BOLT
AK SERIES-STOCK LENGTH COUPLING
AP SERIES-CUSTOM LENGTH COUPLING
The AK and AP series couplings are standard design spacer couplings. They are made up of two hubs, a
one-piece machined spool spacer and two sets of flex discs with standard hardware, including stainless
steel flex discs. The AK is the stocked minimum length spacer. The AP is made-to-order to any custom
spacer length. AP series pricing is standard for any spacer length up to 9 inches.
RATED MISALIGNMENT: 1.0 DEG/DISC
HUB OPTIONS
HUB TYPE
AJ - STANDARD
AZ - OVERSIZE
QD BUSHING MT.
AC/AD CLAMP
AL LOCK ELEMENT
SEE PAGE F58
SIZE
05
10
15
20
25
30
35
40
SIZE
05-45
05-45
15-40
05-25
05-25
MAX BORE
AJ
AZ
0.87
1.13
1.25
1.63
1.37
1.88
1.62
2.13
2.00
2.38
2.38
2.88
2.88
3.75
3.25
4.00
A
2.65
3.19
3.65
4.08
4.95
5.63
6.63
7.64
DIMENSIONS IN INCHES*
Bmin
Dmin
F
(AK)
(AK)
3.72
1.72
1.00
4.06
2.06
1.00
4.67
2.41
1.13
5.02
2.38
1.32
6.16
2.92
1.62
7.57
3.81
1.88
8.81
4.31
2.25
9.88
4.88
2.50
MATERIAL
CLASSES
CLASS
SIZE
A
05-45
B
05-45
C
15-45
E
MTO 15-45
SEE PAGE F54
0.24
0.27
0.32
0.34
0.45
0.47
0.55
0.60
1.30
1.80
2.00
2.40
2.80
3.30
4.15
4.65
0.54
0.56
0.88
0.79
1.00
1.14
0.97
1.30
SPACER ASSEMBLY
PART #
AK
AP
AKxxSAA APxxAddd
AKxxSAB APxxBddd
AKxxSAC APxxCddd
AKxxSAE APxxEddd
xx = SIZE ddd=DBSE
FREE END
FLOAT
+/- inch
0.030
0.040
0.042
0.055
0.060
0.065
0.085
0.100
SIZE
05
10
15
20
25
30
35
40
HP PER
100 RPM
1.0 S.F
0.48
1.27
2.50
3.49
6.03
11.00
18.00
29.00
RATED TORQUE
LB*IN
(lb. in.)
300
800
1,575
2,200
3,800
6,930
11,340
18,270
PEAK O/L
TORQUE
(lb. in.)
600
1,600
3,150
4,400
7,600
13,860
22,680
36,540
AGMA 7
MAX
RPM
8,500
7,500
6,700
6,200
5,500
5,000
4,400
4,000
WEIGHT (lbs.)
AT MIN
ADD PER
D
in. OF D
2.32
0.14
3.62
0.22
5.44
0.26
6.96
0.32
12.7
0.41
19.0
0.46
27.6
0.63
42.1
0.76
WR2-(lb. in.2)
AT MIN
ADD PER
D
in. OF D
1.87
0.05
4.48
0.11
8.86
0.19
13.8
0.34
38.8
0.62
77.7
0.92
156
2.29
322
3.55
NOTES:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR AJ HUBS AT MAXIMUM BORE SIZE.
2) TO CALCULATE TORSIONAL STIFFNESS FOR A GIVEN SPACER LENGTH, LET L= D - Dmin
TORSIONAL STIFFNESS = 1/[(1/K) + (L/Y)]
F520
TORS. STIFFNESS
106 (lb. in./rad)
K factor
Y factor
0.15
2.00
0.43
4.64
0.74
7.51
1.08
13.8
1.74
25.1
2.89
37.4
5.34
93
8.21
144
SPACER BP SERIES
6 BOLT SPACER COUPLING
The BP series coupling is a standard design spacer coupling using the 6 bolt disc design. The coupling is
made up of two hubs, a one-piece machined spool spacer and two sets of flex discs with standard
hardware, including stainless steel flex discs. The BP is made-to-order to any custom spacer length.
BP series pricing is standard for any spacer length up to 9 inches.
DIMENSIONS IN INCHES
33
38
43
48
53
58
2.25
3.00
3.25
3.75
3.88
4.25
4.69
5.87
6.70
7.50
7.87
9.00
2.09
2.37
2.95
3.00
3.91
4.80
1.75
2.25
2.50
2.75
2.88
3.25
0.285
0.335
0.465
0.495
0.520
0.555
3.14
4.13
4.63
5.40
5.65
6.22
FREE
END
FLOAT
+/- inch
0.060
0.084
0.090
0.108
0.108
0.118
63
68
4.88
5.00
10.00
10.75
4.88
6.20
3.38
3.75
0.600
0.849
7.14
7.33
0.140
0.144
SIZE
SIZE
33
MAX
BORE
HP PER
100 RPM
1.0 S.F
4.84
Dmin
RATED TORQUE
LB*IN
(lb. in.)
3,050
PEAK O/L
TORQUE
(lb. in.)
6,100
AGMA 8
MAX
RPM
8,400
MATERIAL
CLASSES
CLASS
SIZE
A
33-73
B
33-78
C
38-63
E
N/A
SEE PAGE F54
WEIGHT (lbs.)
AT MIN
ADD PER
D
in. OF D
8.49
0.47
38
43
10.08
19.84
6,350
12,500
12,700
25,000
7,500
6,800
15.9
24.3
0.63
0.74
48
53
58
63
68
26.98
38.10
53.97
76.19
114.29
17,000
24,000
34,000
48,000
72,000
34,000
48,000
68,000
96,000
144,000
6,500
6,000
5,500
5,200
4,800
33.2
41.7
65.1
80.5
104
0.87
0.93
0.98
1.14
1.17
WR2-(lb. in.2)
AT MIN
ADD PER
D
in. OF D
23.3
0.91
71.8
143
248
354
707
1,100
1,560
2.24
3.59
5.79
6.93
8.14
13.0
14.7
SPACER
ASSEMBLY
PART #
BPxxAddd
BPxxBddd
BPxxCddd
N/A
ddd = DBSE
TORS. STIFFNESS
x106 (lb. in./rad)
K factor
Y factor
2.42
37.1
4.93
9.40
13.2
15.1
23.7
34.9
44.0
90.8
146.
235.
281.
330.
528.
597.
NOTES:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR BH HUBS AT MAXIMUM BORE SIZE.
2) TO CALCULATE TORSIONAL STIFFNESS FOR A GIVEN SPACER LENGTH, LET L= D - Dmin
TORSIONAL STIFFNESS = 1/[(1/K) + (L/Y)]
F521
SPACER DP SERIES
8 BOLT SPACER COUPLINGS
The DP series coupling is a fully machined spacer coupling using the 8 bolt disc design used for high
torque applications at higher speeds. The coupling is made up of two hubs, a one-piece machined spool
spacer and two sets of flex discs and hardware. The DP is made-to-order to any customer spacer length.
Both stainless and high strength alloy flex disc materials are available.
SIZE
DP31
DP35
DP37
DP42
DP45
DP50
DP55
DP60
DP70
MAX BORE
DA
DH
3.38
3.63
3.75
4.00
4.00
4.50
4.50
4.75
4.75
5.13
5.00
5.38
5.50
6.00
6.00
6.50
7.00
7.50
7.81
8.69
9.69
10.50
11.31
12.88
14.44
16.00
18.25
SIZE
HP PER
100 RPM
1.0 S.F
RATED TORQUE
LB*IN
(lb. in.)
DP31
DP35
DP37
DP42
DP45
DP50
DP55
DP60
DP70
50.75
76.12
107.84
146.69
157.00
260.08
396.47
586.77
840.51
32,000
48,000
68,000
92,500
99,000
164,000
250,000
370,000
530,000
DIMENSIONS IN INCHES
Dmin
F1
F2
DBSE
DA
DH
4.38
2.84
3.37
4.75
3.28
3.75
5.00
3.56
4.00
5.13
3.97
4.25
5.25
4.50
4.50
7.25
4.72
5.00
7.62
5.31
5.50
8.13
6.00
6.00
9.25
7.00
7.00
PEAK O/L
TORQUE
(lb. in.)
64,000
96,000
136,000
185,000
198,000
328,000
510,000
740,000
1,060,000
AGMA 8
MAX
RPM
6,500
5,700
5,400
5,100
4,800
4,300
4,100
3,600
3,300
G
0.44
0.54
0.69
0.69
0.75
0.96
1.04
1.10
1.40
WEIGHT (lbs.)
AT MIN
ADD PER
D
in. OF D
37.2
54.5
69.3
91.4
118
175
260
367
559
0.60
0.97
1.05
1.54
1.66
2.28
3.03
4.01
5.46
H1
DA
5.22
5.71
6.18
6.70
7.20
7.93
8.95
9.89
11.06
WR2-(lb. in.2)
AT MIN
ADD PER
D
in. OF D
289
525
839
1,270
1,910
3,560
6,690
11,600
23,500
NOTES:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR DA HUBS AT MAXIMUM BORE SIZE.
2) TO CALCULATE TORSIONAL STIFFNESS FOR A GIVEN SPACER LENGTH, LET L= D - Dmin
TORSIONAL STIFFNESS = 1/[(1/K) + (L/Y)]
F5-22
H2
DH
5.50
5.88
6.50
7.00
7.44
8.38
9.44
10.25
11.75
4.30
8.16
10.7
18.2
23.4
38.3
63.2
101
172
FREE END
FLOAT
+/- inch
0.052
0.056
0.062
0.067
0.072
0.082
0.092
0.102
0.115
TORS. STIFFNESS
x106 (lb. in./rad)
K factor
Y factor
16.7
26.7
34.7
47.2
61.0
78.7
133
187
285
168
318
417
711
912
1,490
2,470
3,950
6,690
SPACER BF SERIES
6 BOLT DROP OUT SPACER COUPLING
The BF series is designed for moderate service in higher speed applications. The coupling consists of
factory assembled spacer unit which mounts between two hubs. The spacer assembly drops out as one
unit for easy maintenance. The BF has all steel construction with standard stainless steel flex discs.
The coupling is manufactured to meet AGMA class 9 balance requirements. Dynamic balancing for higher
speed operation is also available. Standard length spacers are stocked. Pricing is standard for any spacer
length up to the Dmax value listed. Longer spacer lengths are also available.
SIZE
15(3)
20(3)
33
38
43
48
53
58
63
68
73
78
STD
EXT
1.50
1.88
2.25
3.00
3.50
3.75
4.13
4.63
5.13
5.63
6.50
7.50
MAX BORE
INTERM. LARGE
HUB
HUB
1.88
2.38
2.13
2.75
3.25
4.00
4.50
5.00
-
Dmin
3.65
4.19
4.93
6.00
6.77
7.62
8.00
9.00
10.00
11.00
12.75
15.30
3.43
3.43
3.09
3.50
4.43
4.50
5.69
6.88
6.93
7.56
11.00
11.08
Fe
EXT
Fl
LRG
G
MAX
1.69
2.06
2.50
3.25
3.75
4.00
4.38
5.00
5.38
6.00
6.38
7.38
1.63
1.81
2.06
2.75
3.00
3.25
-
2.09
2.56
3.13
4.13
5.00
5.38
5.75
6.50
7.25
8.00
8.38
10.19
Hs
STD
EXT
2.33
2.81
3.38
4.43
5.25
5.63
6.13
6.88
7.63
8.38
9.38
10.75
Hm
INTERM.
2.75
3.00
-
SIZE
(4)
15
20
33
38
43
48
53
58
63
68
73
78
1,575
2,200
3,950
8,255
13,500
18,400
24,000
41,000
48,000
72,000
125,000
233,000
13,500
12,500
11,000
9,800
8,800
8,300
7,800
7,000
6,700
6,200
5,700
5,000
7.22
9.31
13.1
24.3
44.5
54.3
72
107
134
188
272
475
0.12
0.19
0.47
0.63
0.70
0.79
0.88
0.98
1.14
1.48
2.02
3.21
TORSIONAL STIFFNESS
WR2-(lb. in.2)
AT MIN. ADD PER
x106 (lb. in./rad)
D
(in.) OF D K factor
Y factor
11.9
19.9
39.3
114.0
276
422
633
1,200
1,870
3,020
5,890
14,700
0.05
0.15
0.91
2.23
3.05
4.61
5.92
8.14
13.0
16.2
27.0
63.8
0.52
0.92
3.32
6.91
9.66
12.8
14.9
23.4
33.5
44.7
75.1
142
2.09
3.72
37.0
90.7
124
187
240
330
528
569
1,100
2,590
FREE END
FLOAT
+/- inch
0.045
0.055
0.060
0.076
0.090
0.108
0.108
0.118
0.140
0.144
0.156
0.170
NOTES:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR STANDARD HUBS AT MAXIMUM BORE SIZE.
2) TO CALCULATE TORSIONAL STIFFNESS FOR A GIVEN SPACER LENGTH, LET L= D - Dmin
TORSIONAL STIFFNESS = 1/[(1/K) + (L/Y)]
3) CONSULT FACTORY FOR HIGHER SPEED OPERATION
4) SIZES 15-20 ARE A 4-BOLT DISC DESIGN, SIZES 33-68 ARE A 6-BOLT DISC DESIGN AND SIZES 73-78 ARE AN 8-BOLT DESIGN.
F5-23
SIZE
22
26
31
35
37
42
45
50
55
60
70
75
80
85
92
105
160
SIZE
22
26
31
35
37
42
45
50
55
60
70
75
80
85
92
105
160
MAX BORE
IRON
STEEL
2.25
2.62
3.12
3.63
3.62
4.00
3.75
4.50
4.25
4.75
4.50
5.13
5.12
5.50
5.62
6.25
6.50
7.12
7.00
7.87
7.75
8.75
8.00
9.12
8.50
9.62
10.00
11.00
10.50
12.00
16.00
17.00
HP PER
100 RPM
1.0S.F
15.08
25.40
38.10
69.84
95.24
115.90
157.10
203.20
300.00
414.30
658.70
846.00
1,087.00
1,316.00
1,651.00
1,984.00
3,175.00
DIMENSIONS IN INCHES
D
A (2)
B
DBSE
6.00
6.87
8.12
9.12
10.06
11.00
11.87
13.43
15.00
16.75
18.93
20.62
22.37
23.75
25.75
29.25
33.50
RATED TORQUE
(lb. in.)
9,500
16,000
24,000
44,000
60,000
73,000
99,000
128,000
189,000
261,000
415,000
533,000
685,000
829,000
1,040,000
1,250,000
2,000,000
8.00
9.50
10.87
12.06
13.12
13.93
14.75
16.81
18.68
20.93
23.62
25.00
26.87
28.62
31.00
34.25
40.25
PEAK O/L
TORQUE
(lb. in.)
14.250
24,000
36,000
66,000
90,000
109,500
148,500
192,000
283,500
391,500
622,500
799,500
1,027,500
1,243,500
1,560,000
1,875,000
3,000,000
3.00
3.50
4.12
4.56
5.12
5.43
5.75
6.81
7.68
8.43
9.62
10.50
11.37
12.12
13.00
13.25
16.25
MAX
RPM
3,800
3,300
2,800
2,600
2,500
2,400
2,250
2,000
1,800
1,600
1,400
1,300
1,200
1,100
1,000
1,000
900
2.50
2.88
3.37
3.75
4.00
4.25
4.50
5.00
5.50
6.25
7.00
7.25
7.75
8.25
9.00
10.50
12.00
0.43
0.55
0.62
0.66
0.81
0.81
0.87
1.06
1.25
1.34
1.50
1.53
1.56
1.62
1.75
1.75
2.25
3.87
4.50
5.50
6.12
6.50
7.00
7.43
9.50
9.50
10.50
11.75
13.00
13.75
14.50
15.87
20.00
24.00
WEIGHT
(lbs.)
(1)
22
33
56
81
103
133
161
223
302
435
640
839
1,070
1,240
1,710
C/F
C/F
WR2
(lb. in.2)
(1)
80
161
401
750
1,130
1,740
2,510
4,580
7,480
13,800
25,900
38,600
59,800
79,400
131,000
C/F
C/F
ORDERING: HSH
Series couplings are sold
as complete assemblies.
Please specify hub type,
bore sizes, and flex disc
materials. A coupling will
be configured to meet
your specifications.
TQ/RAD
X10 6 (1)
(lb. in./rad)
1.5
2.3
2.9
6.5
9.9
6.9
14.8
44.3
54.2
80.1
144
148
205
204
384
C/F
C/F
NOTE:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR CAST IRON HUBS AT MAXIMUM BORE SIZE.
2) HUB FLANGE DIAMETER MAY VARY WITH STEEL HUBS
F524
HUB TYPES
C.I.
STL
SEE PAGE
FREE END
FLOAT
+/- inch
0.036
0.044
0.052
0.056
0.062
0.067
0.072
0.082
0.092
0.102
0.115
0.125
0.136
0.140
0.156
0.170
0.250
SIZES
22-160
31-160
F59
HUB TYPES
C.I.
STL.
SEE PAGE
SIZE
OD
10
12
14
18
20
22
26
28
10.375
12.375
13.875
18.375
20.375
22.500
26.500
28.875
SIZE
31
35
37
42
45
50
55
60
70
75
80
85
92
105
SIZE
31
35
37
42
45
50
55
60
70
75
80
85
92
105
SIZES
31-105
31-105
F59
MAX BORE
IRON
STEEL
3.12
3.63
3.62
4.00
3.75
4.50
4.25
4.75
4.50
5.13
5.12
5.50
5.62
6.25
6.50
7.12
7.00
7.87
7.75
8.75
8.00
9.12
8.50
9.62
10.00
11.00
10.50
12.00
HP PER
100 RPM
1.0S.F
38.10
69.84
95.24
115.9
157.1
203.2
300.0
414.3
658.7
846.0
1087
1316
1651
1984
A(3)
8.12
9.12
10.06
11.00
11.87
13.43
15.00
16.75
18.93
20.62
22.37
23.75
25.75
29.25
RATED TORQUE
(lb. in.)
24,000
44,000
60,000
73,000
99,000
128,000
189,000
261,000
415,000
533,000
685,000
829,000
1,040,000
1,250,000
DIMENSIONS IN INCHES
D
B
F
DBSE
8.68
5.31
3.37
9.62
5.87
3.75
10.62
6.62
4.00
11.37
7.12
4.25
12.00
7.50
4.50
13.75
8.75
5.00
15.38
9.87
5.50
17.12
10.87
6.25
19.43
12.43
7.00
20.75
13.50
7.25
22.50
14.75
7.75
23.93
15.68
8.25
26.25
17.25
9.00
27.77
17.27
10.50
PEAK O/L
TORQUE
(lb. in.)
36,000
66,000
90,000
109,500
148,500
192,000
283,500
391,500
622,500
799,500
1,027,500
1,243,500
1,560,000
1,875,000
MAX
RPM
(2)
2,800
2,600
2,500
2,400
2,250
2,000
1,800
1,600
1,400
1,300
1,200
1,100
1,000
1,000
WEIGHT
(lbs.)
(1)
48
64
87
115
138
202
263
359
559
766
930
1,110
1,460
C/F
0.62
0.66
0.81
0.81
0.87
1.06
1.25
1.34
1.50
1.53
1.56
1.62
1.75
1.75
5.50
6.12
6.50
7.00
7.43
8.37
9.50
10.50
11.75
13.00
13.75
14.50
15.87
20.00
0.50
0.50
0.56
0.63
0.69
0.75
0.88
1.00
1.00
1.13
1.25
1.25
1.38
1.75
WR2
(lb. in.2)
(1)
442
661
1,170
1,860
2,500
5,550
8,000
12,700
26,200
43,600
60,100
83,000
124,000
C/F
TQ/RAD
X10 6 (1)
(lb. in./rad)
2.95
6.69
10.3
7.03
15.4
48.8
58.6
86.5
161
160
225
222
433
C/F
FREE END
FLOAT
+/- inch
0.052
0.056
0.062
0.067
0.072
0.082
0.092
0.102
0.115
0.125
0.136
0.140
0.156
0.170
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR CAST IRON HUBS AT MAXIMUM BORE SIZE AND MINIMUM
AVAILABLE ADAPTER O.D.
2) MAX RPM LISTED IS FOR SMALLEST ADAPTER SIZE. CONSULT FACTORY FOR SPEED RATINGS BY ADAPTER SIZE.
3) HUB FLANGE DIAMETER MAY VARY WITH STEEL HUBS.
F525
HUB OPTIONS
HUB TYPE
AJ - STANDARD
AZ - OVERSIZE
QD BUSHING MOUNT
AC/AD CLAMP
AL LOCK ELEMENT
SEE PAGE F58
SIZE
05-45
05-45
15-40
05-25
05-25
ORDERING: A5 Series couplings are sold as complete assemblies. Please specify hub
types and bore sizes, DBSE (D) dimension, speed for dynamic balancing, and material class.
A coupling will be configured to meet your specifications.
ORDERING TYPE A6 FOR VERTICAL APPLICATIONS LONGER THAN 30 DBSE.
A THRUST BUTTON WILL BE ADDED ON THE LOWER END OF THE SPACER TO
SUPPORT THE WEIGHT OF THE SPACER
DIMENSIONS IN INCHES*
SIZE
05
10
15
20
25
30
35
40
MAX BORE
AJ
AZ
0.87
1.13
1.25
1.63
1.37
1.88
1.62
2.13
2.00
2.38
2.38
2.88
2.88
3.75
3.25
4.00
Dmin
2.65
3.19
3.65
4.08
4.95
5.63
6.63
7.64
4.00
4.00
5.00
5.00
5.00
6.00
7.00
7.00
1.00
1.00
1.13
1.32
1.62
1.88
2.25
2.50
0.24
0.27
0.32
0.34
0.45
0.47
0.55
0.60
1.30
1.80
2.00
2.40
2.80
3.30
4.15
4.65
1800
51
62
64
73
79
85
97
103
MATERIAL
CLASSES
CLASS SIZE
A
05-45
B
05-45
C
15-45
E
15-45
SEE PAGE F54
600
87
107
111
126
137
147
168
178
SIZE
05
10
15
20
25
30
35
40
HP PER
100 RPM
1.0 S.F
0.48
1.27
2.50
3.49
6.03
11.00
18.00
29.00
RATED TORQUE
(lb. in.)
300
800
1,575
2,200
3,800
6,930
11,340
18,270
PEAK O/L
TORQUE
(lb. in.)
600
1,600
3,150
4,400
7,600
13,860
22,680
36,540
WEIGHT (lbs.)
AT
ADD PER
D = 20
in. OF D
4.37
0.11
5.64
0.10
7.48
0.10
11.5
0.21
17.0
0.20
25.7
0.29
34.8
0.40
49.9
0.46
WR2-(lb. in.2)
AT
ADD PER
D = 20
in. OF D
2.38
0.03
5.88
0.07
10.3
0.07
18.3
0.22
45.0
0.29
90.6
0.56
180
1.32
356
1.95
NOTES:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR AJ HUBS AT MAXIMUM BORE SIZE.
2) TO CALCULATE TORSIONAL STIFFNESS FOR A GIVEN SPACER LENGTH, LET L= D - 20
TORSIONAL STIFFNESS = 1/[(1/K) + (L/Y)]
F526
TORS. STIFFNESS
106 (lb. in./rad)
K factor
Y factor
0.04
1.12
0.11
2.81
0.13
2.81
0.35
8.77
0.52
12.0
0.98
22.7
1.99
53.9
3.14
79.3
FREE END
FLOAT
+/- inch
0.030
0.040
0.042
0.055
0.060
0.065
0.085
0.100
HUB OPTIONS
HUB TYPE
AJ - STANDARD
AZ - OVERSIZE
QD BUSHING MOUNT
AC/AD CLAMP
AL LOCK ELEMENT
SEE PAGE F58
SIZE
05-45
05-45
15-40
05-25
05-25
ORDERING: A7 Series couplings are sold as complete assemblies. Please specify hub
types and bore sizes, DBSE (D) dimension, speed for dynamic balancing, and material class.
A coupling will be configured to meet your specifications.
DIMENSIONS IN INCHES*
SIZE
10
15
20
25
30
35
40
MAX BORE
AJ
AZ
1.25
1.63
1.37
1.88
1.62
2.13
2.00
2.38
2.38
2.88
2.88
3.75
3.25
4.00
Dmin
3.19
3.65
4.08
4.95
5.63
6.63
7.64
20
20
20
20
20
20
20
1.00
1.13
1.32
1.62
1.88
2.25
2.50
0.27
0.32
0.34
0.45
0.47
0.55
0.60
1.80
2.00
2.40
2.80
3.30
4.15
4.65
1.25
1.25
1.50
1.75
2.00
2.50
3.00
16.50
16.06
15.75
15.25
14.50
13.25
12.75
3.50
3.94
4.25
4.75
5.50
6.75
7.25
KEYWAY
SIZE
.25 x .12
.25 x .12
.37 x .18
.37 x .18
.50 x .25
.62 x .31
.75 x .37
MATERIAL
CLASSES
CLASS SIZE
A
10-45
B
05-45
C
15-45
E
15-45
SEE PAGE F54
600
107
111
126
137
147
168
178
SIZE
10
15
20
25
30
35
40
HP PER
100 RPM
1.0 S.F
1.27
2.50
3.49
6.03
11.00
18.00
29.00
RATED TORQUE
(lb. in.)
800
1,575
2,200
3,800
6,930
11,340
18,270
PEAK O/L
TORQUE
(lb. in.)
1,600
3,150
4,400
7,600
13,860
22,680
36,540
MAX
RADIAL
LOAD-(lbs.)
34
56
125
183
275
400
600
WEIGHT (lbs.)
AT
ADD/ (in.)
D = 20
OF D
5.37
0.10
6.65
0.10
11.0
0.21
14.7
0.20
19.7
0.29
34.7
0.40
51.6
0.46
WR2-(lb. in.2)
AT MIN
ADD/ (in.)
D = 20
OF D
3.30
0.07
5.72
0.07
11.0
0.22
24.9
0.29
52.4
0.56
106
1.32
211
1.95
TORS. STIFFNESS
106 (lb. in./rad)
K factor
Y factor
0.26
2.81
0.28
2.81
0.56
8.77
0.91
12.0
1.52
22.7
3.03
53.9
5.26
79.3
FREE END
FLOAT
+/- inch
0.020
0.021
0.027
0.030
0.032
0.042
0.050
NOTES:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR AJ HUBS AT MAXIMUM BORE SIZE.
2) TO CALCULATE TORSIONAL STIFFNESS FOR A GIVEN SPACER LENGTH, LET L= D - 20
TORSIONAL STIFFNESS = 1/[(1/K) + (L/Y)]
F527
MATERIAL
CLASSES
CLASS SIZE
A
33-78
B
33-78
C
38-63
E
N/A
SEE PAGE F54
ORDERING: B5 Series couplings are sold as complete assemblies. Please specify hub
types and bore sizes, DBSE (D) dimension, speed for dynamic balancing, and material class.
A coupling will be configured to meet your specifications.
DIMENSIONS IN INCHES*
SIZE
33
38
43
48
53
58
63
68
SIZE
33
38
43
48
53
58
63
68
MAX
BORE
2.25
3.00
3.25
3.75
3.88
4.25
4.88
5.00
Dmin
4.69
5.87
6.70
7.50
7.87
9.00
10.00
10.75
4.25
6.00
7.00
7.50
7.50
7.50
7.50
8.00
1.75
2.25
2.50
2.75
2.88
3.25
3.38
3.75
HP PER
100 RPM
1.0 S.F
4.84
10.08
19.84
26.98
38.10
53.97
76.19
114.29
RATED TORQUE
LB*IN
(in. lbs.)
3,050
6,350
12,500
17,000
24,000
34,000
48,000
72,000
PEAK O/L
TORQUE
(in. lbs.)
6,100
12,700
25,000
34,000
48,000
68,000
96,000
144,000
G
0.285
0.335
0.465
0.495
0.520
0.555
0.600
0.849
H
3.14
4.13
4.63
5.40
5.65
6.22
7.14
7.33
WEIGHT (lbs.)
AT
ADD PER
D = 20
in. OF D
14.4
0.20
29.1
0.39
41.0
0.44
60.0
0.52
67.4
0.52
85.5
0.63
108
0.63
140
1.15
1800
79
97
103
113
113
123
123
130
WR2-(lb. in.2)
AT
ADD PER
D = 20
in. OF D
32.7
0.29
113
1.28
210
1.88
402
3.10
494
3.10
874
5.43
1340
5.43
1940
13.37
NOTES:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR BH HUBS AT MAXIMUM BORE SIZE.
2) TO CALCULATE TORSIONAL STIFFNESS FOR A GIVEN SPACER LENGTH, LET L= D - 20
TORSIONAL STIFFNESS = 1/[(1/K) + (L/Y)]
F528
750
122
150
160
175
175
186
186
201
TORS. STIFFNESS
x106 (in. lbs./rad)
K factor
Y factor
0.48
12.0
1.77
51.9
2.89
76.4
4.57
126
5.52
126
8.44
220
9.52
220
19.9
543
600
137
168
178
196
196
208
208
225
FREE END
FLOAT
+/- inch
0.060
0.084
0.090
0.108
0.108
0.118
0.140
0.144
DIMENSIONS IN INCHES*
SIZE
35
37
42
45
50
55
60
70
75
80
85
92
105
160
SIZE
35
37
42
45
50
55
60
70
75
80
85
92
105
160
MAX BORE
STEEL
4.00
4.50
4.75
5.13
5.50
6.25
7.12
7.87
8.75
9.12
9.62
11.00
12.00
17.00
HP PER
100 RPM
1.0 S.F
76.12
107.8
146.7
157.0
260.1
396.5
586.8
840.5
1142
1507
1903
2062
2855
3806
Dmin
9.12
10.06
11.00
11.87
13.43
15.00
16.75
18.93
20.62
22.37
25.75
25.75
29.25
33.50
10.0
10.0
10.0
10.0
10.0
10.0
15.0
15.0
15.0
15.0
20.0
20.0
20.0
20.0
3.75
4.00
4.25
4.50
5.00
5.50
6.25
7.00
7.25
7.75
8.25
9.00
10.50
12.00
RATED TORQUE
(lb. in.)
48,000
68,000
92,500
99,000
164,000
250,000
370,000
530,000
720,000
950,000
1,200,000
1,300,000
1,800,000
2,400,000
PEAK O/L
TORQUE
(lb. in.)
96,000
136,000
185,000
198,000
328,000
500,000
740,000
1,060,000
1,440,000
1,900,000
2,400,000
2,600,000
3,600,000
4,800,000
G
0.66
0.81
0.81
0.87
1.06
1.25
1.34
1.50
1.55
1.56
1.62
1.75
1.75
2.25
H
6.12
6.50
7.00
7.43
8.37
9.50
10.50
11.75
13.00
13.75
14.50
15.87
20.00
24.00
1800
114
121
128
130
139
145
153
161
172
182
600
197
210
222
226
242
252
266
279
299
315
CONSULT TB WOODS
CONSULT TB WOODS
FREE END
FLOAT
+/- inch
0.056
.062
0.067
0.072
0.082
0.092
0.102
0.115
0.125
0.136
0.140
0.166
0.170
0.250
NOTES:
1) WEIGHT, WR2 AND TORSIONAL STIFFNESS VALUES SHOWN ARE FOR BH HUBS AT MAXIMUM BORE SIZE.
2) TO CALCULATE TORSIONAL STIFFNESS FOR A GIVEN SPACER LENGTH, LET L= D - 20
TORSIONAL STIFFNESS = 1/[(1/K) + (L/Y)]
F529
True-Tube composite tubes are high-strength, lightweight torque tubes for long span drive shafts. These
tubes are filament wound carbon or glass fiber construction in an oven cured epoxy matrix. True-Tube
composites offer the following advantages over steel tubing.
LONGER SPANS
TrueTube composite tubes have a higher stiffness to weight ratio than steel tubing. That
increases the critical speed of the tubing and allows longer spans without center bearings.
LIGHT WEIGHT
TrueTube drive shafts weigh up to 80% less than equivalent steel driveshafts. That
means better balance and reduced vibration. Bearing life may be improved by
minimizing overhung weight.
DESIGN FLEXIBILITY
TrueTube composite tubes may be custom designed to meet your requirements for
torsional stiffness, critical speed or torque capacity. With TrueTube, a designer can tune
torsional or lateral critical speeds out of a machine system.
All TrueTube products include an ultraviolet barrier that is wound into the structure of the tube before
it is cured. This UV barrier eliminates the need for paints or other protective coatings and results in a
smooth, durable finish that other composite tubes dont offer. TrueTube products are cured in an enclosed
oven to assure consistent strength and quality. Design data is shown below for standard series tubes.
Standard series tubes are designed for maximum length at moderate torques. High torque designs are also
available.
MODEL
NUMBER
TUBE
I.D.
INCHES
TUBE
O.D.
INCHES
SLEEVE
O.D.
INCHES
SL2.0
SL3.0
SL4.0
SL6.0
SL8.0
SL10.0
SL12.0
2.00
3.00
4.00
6.00
8.00
10.00
12.00
2.30
3.25
4.23
6.25
8.25
10.25
12.25
2.40
3.50
4.50
6.63
8.63
10.75
12.75
SS2.0
SS3.0
SS4.0
SS6.0
SS8.0
SS10.0
SS12.0
2.00
3.00
4.00
6.00
8.00
10.00
12.00
2.30
3.25
4.23
6.25
8.25
10.25
12.25
2.40
3.50
4.50
6.63
8.63
10.75
12.75
LS2.0
LS3.0
LS4.0
LS6.0
LS8.0
LS10.0
LS12.0
2.00
3.00
4.00
6.00
8.00
10.00
12.00
2.30
3.25
4.23
6.25
8.25
10.25
12.25
2.40
3.50
4.50
6.63
8.63
10.75
12.75
RATED
TUBE
TORSIONAL
TORQUE
WEIGHT
STIFFNESS
LB*IN
(lb./in.)
x106 LB*IN/RAD
SERIES SL ALL CARBON CONSTRUCTION
6,500
0.05
1.26
12,000
0.08
3.61
22,000
0.11
8.60
42,000
0.20
34.4
63,000
0.24
80.2
80,000
0.32
155
100,000
0.38
258
SERIES SS CARBON/GLASS CONSTRUCTION
5,500
0.06
0.97
10,500
0.08
2.86
22,000
0.12
7.28
42,000
0.20
26.4
58,000
0.28
57.3
73,000
0.34
115
88,000
0.42
206
SERIES LS ALL GLASS CONSTRUCTION
5,000
0.07
0.75
10,000
0.09
2.06
18,000
0.14
5.04
39,000
0.23
18.9
51,000
0.30
43.0
64,000
0.37
86.0
77,000
0.46
149
F530
2000
RPM
MAX TUBE
LENGTH
INCHES
90
110
127
152
180
199
215
95
116
134
160
190
210
227
104
127
147
175
208
230
249
127
155
180
214
255
281
304
82
128
145
177
192
232
232
79
97
112
135
151
173
189
83
102
118
142
160
183
199
91
112
129
155
176
200
218
111
137
158
190
216
245
267
82
128
145
177
192
232
232
66
80
93
110
128
142
155
70
84
98
116
135
150
163
77
92
107
127
148
164
178
94
113
131
155
181
201
218
82
128
145
177
192
232
232
RATED
COUPLING TORQUE
TYPE
LB IN
MAXIMUM DBSE-INCHES
HP PER
100 RPM
COUPLING
PRODUCT NO.
MAX
A520-CS2G
A520-CS2R
A525-CS2G
A525-CS2R
A530-CS3R
A530-CS3B
A535-CS4R
A535-CS4B
A535-CS6R
A535-CS6B
A535-CS8R
A535-CS8B
A540-CS4R
A540-CS4B
B558-CS6R
B558-CS6B
B558-CS6X
B558-CS8R
B558-CS8B
B558-CS10R**
B558-CS10B**
83
83
83
83
128
128
146
146
179
179
196
196
146
146
179
179
182
196
196
236
236
A520
2,200
3.49
A525
3,800
6.03
A530
6,930
11.00
A535
11,340
18.00
A540
18,270
29.00
B558
34,000
54.00
1800
RPM
1500
RPM
70
83
70
83
102
116
118
134
142
160
175
190
118
134
142
160
165
175
190
206
210
77
83*
77
83*
112
127
129
146*
155
175
191
207*
129
146*
155
175
181
191
207
224
230
DIMENSIONS IN INCHES
MAXIMUM BORE
A
2.125
4.08
1.32
0.34
2.40
2.000
2.375
4.95
1.62
0.45
2.80
2.375
2.875
5.63
1.88
0.47
3.30
2.875
3.750
6.63
2.25
0.55
4.15
3.250
4.000
7.63
2.50
0.60
4.65
3.75
9.00
2.75
0.56
5.43
2.30
2.30
2.30
2.30
3.25
3.25
4.25
4.25
6.30
6.30
8.31
8.31
4.25
4.25
6.30
6.30
6.30
8.31
8.31
10.31
10.31
STD HUB
AZ HUB
1.625
COMPOSITE TUBE
CONSTRUCTION
COUPLING
MODEL
A520-CS2G
HD4-CS2G***
A525-CS2G
A525-CS2R
HD4-CS2R***
A525-CS2R
A530-CS3R
A530-CS3B
A535-CS4R
A540-CS4R
A535-CS4B
A540-CS4B
A535-CS6R
B558-CS6R
A535-CS6B
B558-CS6B
B558-CS6X
A535-CS8R
B558-CS8R
A535-CS8B
B558-CS8B
B558-CS10R
B558-CS10B
B558-CS12B
1500 RPM
MAX HP
DBSE
25
77
42
42
25
83*
42
42
83
112
83
127
125
129
208
125
146*
208
125
155
333
125
175
333
333
181
125
191
333
125
207
333
333
224
333
230
333
236*
MODEL
CODE
TUBE MATERIAL
OF CONSTRUCTION
G
R
B
X,Z
GLASS
CARBON/GLASS HYBRID
STANDARD CARBON
HIGH MODULUS CARBON
HUB
STEEL
STEEL
ZINC PLT
304SS
MATERIAL USED
HARDWARE
SPACER FLANGES
STEEL
COMPOSITE OR STEEL
STEEL, ZINC PLT
COMPOSITE OR
304SS
ZINC PLATED STEEL
304SS
COMPOSITE OR 304SS
F531
Form-Flex M series microcouplings are a more compact and lighter design than traditional A Series couplings. They
are free from backlash and their high torsional stiffness makes them ideally suited for small servo and tachometer
drives. Aluminum hub construction meets low inertia requirements while the bolted assembly provides superior life
when compared to riveted types.
STYLE MA
STYLE MB
DIMENSIONS IN INCHES
STYLE
STYLE MC
RATED
TORQUE
STD SET
SCREW SIZE (in. lbs.)
PEAK O/L
TORQUE
(in. lbs.)
WR2
OZ. (in.2)
TORSIONAL
STIFFNESS
(in. lbs./rad)
87
174
6.11
64.7X10^3
1.5
0.60
M4X0.7
M4X0.7
M6X1.0
17
35
87
34
70
174
0.29
1.33
4.99
2.9X10^3
14.9X10^3
64.7X10^3
1.5
1.5
1.5
0.40
0.50
0.60
M3X0.5
M4X0.7
M4X0.7
9
17
35
18
34
70
0.17
0.35
1.34
2.4X10^3
2.9X10^3
14.9X10^3
1.5
1.5
1.5
0.25
0.40
0.50
D
DBSE
SIZE
MAX
BORE
04
0.79
2.24
2.93
1.36
0.79
1.22
M6X1.0
02
03
04
0.38
0.63
0.79
1.26
1.65
2.24
1.39
1.80
2.38
0.45
0.54
0.81
0.47
0.63
0.79
0.71
1.02
1.22
01
02
03
0.38
0.59
0.79
1.02
1.26
1.65
1.08
1.53
1.53
0.45
0.45
0.54
0.32
0.32
0.50
RATED
FREE END
MISALIGNMENT
FLOAT
deg/disc
(in.)
MA
MB
MC
NOTE: STYLE MBO4 COUPLING HUBS WILL HAVE ROUND FLANGES AS SHOWN FOR TYPE MA.
F5-32
Repair kits consist of flex discs and all the necessary installation hardware. SINGLE REPAIR KITS have one set of
flex discs and all required hardware. Two single repair kits are required for a double flexing coupling. DOUBLE
REPAIR KITS have two sets of flex discs and all required hardware. HARDWARE KITS have all the components of a
repair kit except the flex discs. FLEX DISCS are also sold individually.
A SERIES (4 BOLT) COUPLING PARTS
KIT TYPE
SGL/DBL
USED ON
MATL CLASS
REPAIR
A,B
05
10
15
20
25
30
35
40
45
A05RKA
A10RKA
A15RKA
A20RKA
A25RKA
A30RKA
A35RKA
A40RKA
A45RKA
HARDWARE
SINGLE
AA, AK, AP, AR, A5, A7
C,E
A,B
...
...
A15RKE
A20RKE
A25RKE
A30RKE
A35RKE
A40RKE
A45RKE
REPAIR
HDWR
DOUBLE
AX
A05HKA
A10HKA
A10HKA
A20HKA
A25HKA
A30HKA
A35HKA
A10HKA
A45HKA
REPAIR
C,E
A,B
A,B
...
...
A15HKE
A20HKE
A25HKE
A30HKE
A35HKE
A15HKE
A45HKE
AX05RKA
AX10RKA
AX15RKA
AX20RKA
AX25RKA
AX30RKA
AX35RKA
AX40RKA
AX45RKA
AX05HKA
AX10HKA
AX15HKA
AX20HKA
AX25HKA
AX30HKA
AX35HKA
AX40HKA
AX45HKA
REPAIR
HDWR
REPAIR
HDWR
DOUBLE
AY
A,B
A,B
AY05RKA
AY10RKA
AY15RKA
AY20RKA
AY25RKA
...
...
...
...
AY05HKA
AY10HKA
AY15HKA
AY20HKA
AY25HKA
...
...
...
...
A0054101
A0104101
A0154101
A0204101
A0254101
A0304101
A0354101
A0404101
A0454101
(EXCEPT BA)
KIT TYPE
SGL/DBL
USED ON
MATL CLASS
HARDWARE
A,B
A,B
A,B
A,B
15
20
33
38
43
48
53
58
63
68
73
78
...
...
B033RKA
B038RKA
B043RKA
B048RKA
B053RKA
B058RKA
B063RKA
B068RKA
...
...
...
...
...
B038RKE
B043RKE
B048RKE
B053RKE
B058RKE
B063RKE
...
...
...
...
...
B033HKA
B038HKA
B043HKA
B048HKA
B053HKA
B058HKA
B063HKA
B068HKA
...
...
...
...
...
B038HKE
B043HKE
B048HKE
B053HKE
B058HKE
B063HKE
...
...
...
BF15RKA
BF20RKA
BF33RKA
BF38RKA
BF43RKA
BF48RKA
BF53RKA
BF58RKA
BF63RKA
BF68RKA
BF73RKA
BF78RKA
BF15HKA
BF20HKA
BF33HKA
BF38HKA
BF43HKA
BF48HKA
BF53HKA
BF58HKA
BF63HKA
BF68HKA
...
...
...
...
BY33RKA
BY38RKA
BY43RKA
BY48RKA
BY53RKA
BY58RKA
BY63RKA
BY68RKA
...
...
...
...
BY33HKA
BY38HKA
BY43HKA
BY48HKA
BY53HKA
BY58HKA
BY63HKA
BY68HKA
...
...
BOLT
WASHER
NUT
D22-6H
D26-6H
D31-6H
D35-6H
D37-6H
D42-6H4*
D45-6H4*
D50-6H4*
D55-6H4*
D60-6H4*
D70-6H
D75-6H4*
D80-6H4*
D85-6H
D92-6H
D22-7
D26-7
D31-7
D35-7
D37-7
D42-7
D45-7
D50-7
D55-7
D60-7
D70-7
D75-74*
D80-7
D85-7
D92-7
D22-6N
D26-6N
D31-6N
D35-6N
D37-6N
D42-6N
D45-6N
D50-6N
D55-6N
D60-6N
D70-6N
D75-6N4*
D80-6N
D85-6N
D92-6N
SINGLE
BH, BP, B5
FLEX
DISC
ALL
ALL
SINGLE
BF
REPAIR
HDWR
DOUBLE
BY
A,B
A,B
FLEX
DISC
ALL
ALL
A0154101
A0204101
B0334101
B0384101
B0434101
B0484101
B0534101
B0584101
B0634101
B0684101
...
...
CPLG
SIZE
22
26
31
35
37
42
45
50
55
60
70
75
80
85
92
SS DISC
D22-DF
D26-DF
D31-DF
D35-DF
D37-DF
D42-DF4*
D45-DF4*
D50-DF4*
D55-DF4*
D60-DF4*
D70-DF
D75-DF4*
D80-DF4*
D85-DF
D92-DF
D22-DF-SS
D26-DF-SS
D31-DF-SS
D35-DF-SS
D37-DF-SS
D42-DF4-SS*
D45-DF4-SS*
D50-DF4-SS*
D55-DF4-SS*
D60-DF4-SS*
D70-DF-SS
D75-DF4-SS*
D80-DF4-SS*
D85-DF-SS
D92-DF-SS
SINGLE
HDWR
KIT
D22-BNW
D26-BNW
D31-BNW
D35-BNW
D37-BNW
D42-BNW4*
D45-BNW4*
D50-BNW4*
D55-BNW4*
D60-BNW4*
D70-BNW
D75-BNW4*
D80-BNW4*
D85-BNW
D92-BNW
FLEX DISC
STD
SS
D22-5
D26-5
D31-5
D35-5
D37-5
D42-5
D45-5
D50-5
D55-5
D60-5
D70-5
D75-5
D80-5
D85-5
D92-5
D22-5-SS
D26-5-SS
D31-5-SS
D35-5-SS
D37-5-SS
D42-5-SS
D45-5-SS
D50-5-SS
D55-5-SS
D60-5-SS
D70-5-SS
D75-5-SS
D80-5-SS
D85-5-SS
D92-5-SS
*ITEMS MARKED * HAVE NEW STYLE BOLTS. BOLT HEAD HEX MAY NOT FIT FSH TYPE FLYWHEEL ADAPTERS MANUFACTURED IN 1994 OR EARLIER. TO
RECEIVE OLD STYLE BOLTS, DELETE THE 4 FROM THESE PART NUMBERS.
F5-33
F534
SECTION
F6
GEAR
COUPLINGS
High Torque Capacity
Torsionally Stiff
Good Inherent Balance
Rated for Higher Speeds
Many Types and Configurations
F61
INDEX
Selection
Selection Process...................................................
Service Factor Table ...............................................
Standard Bore Tolerances ......................................
C Series
Continuous Sleeve Gear Coupling ..........................
F Series
Full Flex ..................................................................
Flex Rigid ...............................................................
Floating Shaft .........................................................
Flange Details.........................................................
Short Slide .............................................................
Mill Motor ..............................................................
Limited End Float ...................................................
Vertical Type...........................................................
Stock Spacers, F, MXB, or K100 Series..................
Deck-Flex and Deck-Flex Mite .......................................
F6-2
F6-3
F6-4
F6-5
F6-6
F6-7
F6-7
F6-8
F6-9
F6-10
F6-11
F6-12
F6-13
F6-14
Ordering
Standard gear coupling product is sold by component
See examples on individual pages
F62
Freight
A26 Gravity Discharge
FANS
Centrifugal
Cooling Towers Forced Draft
Induced Draft w/o Damper Control
FEEDERS
Apron
Belt
Disc
Reciprocating
Screw
FOOD INDUSTRY
Beet Slicer
Cereal Cooker
Dough Mixer
Meat Grinder
Bottling, Can Filling Machine
GENERATORS - Not Welding
HAMMER MILLS
LAUNDRY WASHERS - Reversing
LAUNDRY TUMBLERS
LUMBER INDUSTRY
Barkers - Drum Type
Edger Feeder
Live Rolls
Log Haul - Incline
Log Haul - Well Type
Off Bearing Rolls
Planer Feed Chains
Planer Floor Chains
Planer Tilting Hoist
Slab Conveyor
Sorting Table
Trimmer Feed
MACHINE TOOLS
Bending Roll
Plate Planer
Punch Press - Gear Driven
Tapping Machine
Other Machine Tools - Main Drive
Other Machine Tools - Aux. Drive
METAL MILLS
Draw Bench - Carriage
Draw Bench - Main Drive
Forming Machines
Slitters
Table Conveyors - Non-Reversing
Table Conveyors - Reversing
Wire Drawing & Flattening Mach.
Wire Winding Machine
MILLS, ROTARY TYPES
Ball
Cement Kilns
Dryers & Coolers
Kilns
Pebble
Rod
Tumbling Barrels
MIXERS
Concrete Mixers
Drum Type
OIL INDUSTRY
Chillers
Oil Well Pumping
2.00
1.50
1.00
2.00
2.00
1.25
1.25
1.25
2.50
1.25
1.75
1.25
1.75
1.75
1.00
1.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
1.75
1.75
1.75
1.50
1.50
1.75
2.00
1.50
2.00
2.50
1.50
1.25
2.00
2.00
2.00
1.50
2.25
2.50
2.00
1.75
2.25
2.00
2.00
2.00
2.00
2.00
2.00
1.75
1.50
1.25
2.00
1.75
2.00
2.00
2.00
2.25
1.75
1.00
2.00
1.50
1.75
2.00
1.75
1.75
1.25
2.00
1.75
2.00
2.00
1.50
1.50
1.75
1.50
1.50
1.50
2.00
1.00
2.00
2.25
1.75
1.50
2.50
2.00
2.25
2.00
2.50
1.00
2.00
1.00
1.50
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.00
1.00
1.25
1.75
1.50
1.50
1.75
1.50
Above service factors recommended when using electric motors, hydraulic motors, etc.
Add 1.0 to Service Factor shown for internal combustion engines, etc.
F63
Interference Fits
Class I
Class II
Square
Over
To
(Incl.)
Shaft
Tol.(2)
(Minus)
Bore
Tol.
(Plus)
Fit
Tol.
(Plus)
Bore
Tol.
(Plus)
Fit
Tol.
(Plus)
0.4375
0.5625
0.8750
1.2500
1.3750
0.5625
0.8750
1.2500
1.3750
1.5000
0.0005
0.0005
0.0005
0.0005
0.0005
0.0010
0.0010
0.0010
0.0010
0.0010
0.0015
0.0015
0.0015
0.0015
0.0015
0.0020
0.0020
0.0020
0.0020
0.0020
0.0025
0.0025
0.0025
0.0025
0.0025
0.0005
0.0005
0.0005
0.0005
0.0005
0.0010
0.0010
0.0010
0.0010
0.0010
0.0000
0.0000
0.0000
0.0000
0.0000
1.5000
1.7500
2.0000
2.2500
1.7500
2.0000
2.2500
2.7500
0.0010
0.0010
0.0010
0.0010
0.0010
0.0010
0.0015
0.0015
0.0020
0.0020
0.0025
0.0025
0.0020
0.0020
0.0020
0.0020
0.0030
0.0030
0.0030
0.0030
0.0010
0.0010
0.0010
0.0010
0.0020
0.0020
0.0020
0.0020
2.7500
3.0000
3.2500
3.7500
3.0000
3.2500
3.7500
4.0000
0.0010
0.0010
0.0010
0.0010
0.0015
0.0015
0.0015
0.0015
0.0025
0.0025
0.0025
0.0025
0.0020
0.0030
0.0030
0.0030
0.0030
0.0040
0.0040
0.0040
0.0010
0.0015
0.0015
0.0015
4.0000
4.5000
5.0000
5.5000
4.5000
5.0000
5.5000
6.5000
0.0010
0.0010
0.0010
0.0010
0.0015
0.0015
0.0015
0.0015
0.0025
0.0025
0.0025
0.0025
0.0040
0.0040
0.0040
0.0040
0.0050
0.0050
0.0050
0.0050
6.5000
7.0000
7.5000
8.0000
7.0000
7.5000
8.0000
9.0000
0.0010
0.0010
0.0010
0.0010
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
Bore Tolerance
Range
(Minus)
Fit Tolerance
Range
(Minus)
Rectangular
Width
Depth
Width
Depth
0.0010
0.0010
0.0010
0.0010
0.0010
0.1250
0.1875
0.2500
0.3125
0.3750
0.0625
0.0937
0.1250
0.1562
0.1875
0.1250
0.1875
0.2500
0.3125
0.3750
0.0468
0.0625
0.0937
0.1250
0.1250
0.0000
0.0000
0.0000
0.0000
0.0020
0.0020
0.0020
0.0020
0.3750
0.5000
0.5000
0.6250
0.1875
0.2500
0.2500
0.3125
0.3750
0.5000
0.5000
0.6250
0.1250
0.1875
0.1875
0.2187
0.0020
0.0030
0.0030
0.0030
0.0000
0.0005
0.0005
0.0005
0.0020
0.0030
0.0030
0.0030
0.7500
0.7500
0.8750
1.0000
0.3750
0.3750
0.4375
0.5000
0.7500
0.7500
0.8750
1.0000
0.2500
0.2500
0.3125
0.3750
0.0020
0.0020
0.0025
0.0025
0.0035
0.0035
0.0040
0.0040
0.0010
0.0010
0.0015
0.0015
0.0035
0.0035
0.0040
0.0040
1.0000
1.2500
1.2500
1.5000
0.5000
0.6250
0.6250
0.7500
1.0000
1.2500
1.2500
1.5000
0.3750
0.4375
0.4375
0.5000
0.0025
0.0030
0.0030
0.0035
0.0040
0.0050
0.0050
0.0055
0.0015
0.0020
0.0020
0.0025
0.0040
0.0050
0.0050
0.0055
1.7500
1.7500
2.0000
2.0000
0.8750
0.8750
1.0000
1.0000
1.7500
1.7500
2.0000
2.0000
0.7500
0.7500
0.7500
0.7500
2.000 to 2.001
Shaft Size
2.000 to 1.999
____________
Resulting Fit
Loose 0.000 to 0.002
F64
2.000 to 2.002
Shaft Size
2.000 to 1.999
____________
Bore Size
Resulting Fit
Resulting Fit
2.000 to 1.999
1.998 to 1.999
____________
Tight 0.002 to 0.000
Flex-Rigid
Single Engagement (CFR)
STANDARD DIMENSIONS
Size
7/8
1-1/2
2
2-1/2
3
3-1/2
4
4-1/2
5
6
7
9
11
12
A
3.31
3.75
4.75
5.50
6.62
7.50
8.75
9.50
10.75
12.25
14.00
16.25
19.25
20.50
B
3.12
3.75
4.25
4.75
5.50
8.75
9.00
10.25
12.25
13.00
14.88
19.00
22.50
25.00
C
2.00
2.53
2.56
3.06
3.75
4.00
4.62
4.88
5.75
6.50
7.50
8.12
8.12
8.38
D
2.00
2.38
3.25
3.94
4.75
5.38
6.25
7.25
8.25
9.50
10.50
12.62
15.62
16.50
E
1.50
1.81
2.06
2.25
2.62
4.25
4.38
5.00
6.00
6.38
7.25
9.25
11.00
12.25
F
1.00
1.27
1.28
1.53
1.88
2.00
2.31
2.44
2.88
3.25
3.75
4.06
4.06
4.19
G
0.12
0.12
0.12
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.38
0.50
0.50
0.50
G1
0.38
0.50
0.50
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.88
1.00
1.00
1.00
H (1)
3.75
4.59
4.88
5.72
6.88
9.25
9.50
10.38
12.25
13.38
15.38
19.00
22.50
25.00
J
0.12
0.19
0.19
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
K
1.94
2.25
3.00
3.75
4.75
5.50
6.50
7.25
8.12
9.25
9.75
12.50
15.50
16.00
Approx.
Wt. (Lbs.)
Solid Bore
5
8
13
20
33
63
91
126
195
267
320
520
925
1200
RATINGS
SIZE
HP @
100 RPM
TORQUE
in. lbs.
MIN
BORE
7/8
1-1/2
2
2-1/2
3
3-1/2
4
4-1/2
5
6
7
9
11
12
4
12
32
48
80
140
200
292
430
600
950
2000
3500
4000
2520
7560
20160
30240
50400
88200
126000
183960
270900
378000
598500
1260000
2205900
2520000
0.44
0.44
0.56
0.81
1.19
1.56
1.81
1.81
2.56
4.06
4.56
5.94
7.81
9.81
MISALIGNMENT
(3)
MAX
MAX
MAX
ANGULAR PARALLEL
BORE
RPM
RPM
DEGREES
IN
STD KEY UNBALANCED BALANCED PER MESH INCHES (2)
1.25
6000
18000
0.50
0.005
1.62
5000
15000
0.50
0.007
2.12
4200
12600
0.50
0.007
2.62
3750
11250
0.50
0.010
3.12
3000
9000
0.50
0.012
3.62
2800
8400
0.50
0.012
4.12
2400
7200
0.25
0.007
4.75
2200
6600
0.25
0.007
5.75
2100
0.25
0.009
6.62
2000
0.25
0.010
7.50
1000
0.25
0.011
9.50
800
Consult
0.25
0.013
11.50
600
Factory
0.25
0.014
12.50
550
0.25
0.014
*When ordering please specify bore diameter with tolerances for both hubs, keyway sizes, set screws if applicable,
speed, horsepower, and application details.
Below is an ordering example of a Full Flex 4 C Coupling
Item (Qty)
Part Number Description
Flex Hub (2)
G4CRB
4 C Rough Bore Flex Hub
Sleeve (1)
G4CS
4 C Sleeve
Seals & Lockrings for C4 Coupling
Accessory Kit (1) G4CAK
F65
Two Hubs
High quality carbon steel
H (1)
1
1 1/2
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
9
4.56
6.00
7.00
8.38
9.44
11.00
12.50
13.62
15.31
16.75
18.00
20.75
23.25
26.00
3.50
4.00
5.00
6.25
7.38
8.62
9.75
10.94
12.38
14.12
15.12
17.75
22.38
23.50
3.00
3.88
4.81
5.81
6.81
7.84
9.19
10.31
11.44
12.69
13.94
15.75
18.50
20.38
2.31
3.00
4.00
4.62
5.62
6.50
7.50
8.50
9.50
10.50
11.50
13.00
15.50
17.00
1.69
1.94
2.44
3.03
3.59
4.19
4.75
5.31
6.03
6.91
7.41
8.69
11.00
11.50
0.12
0.12
0.12
0.19
0.19
0.25
0.25
0.31
0.31
0.31
0.31
0.38
0.38
0.50
4.19
4.75
6.00
7.12
8.12
9.38
10.25
11.50
13.00
14.38
17.00
20.00
25.00
26.50
Max. Parallel
Approx. Wt.
Misalign(Lbs.) Solid
ment (4)
Bore
0.055
0.060
0.085
0.105
0.115
0.130
0.150
0.175
0.200
0.220
0.120
0.135
0.160
0.165
RATINGS (4)
(1) H Dimension Clearance to
align coupling
SIZE
HP @ 100
RPM
TORQUE
in. lbs.
FLEXIBLE HUBS
MIN BORE MAX BORE MAX BORE
STD KEY
SHALLOW
KEY
MAX RPM
UNBALANCED
MAX RPM
BALANCED
AGMA CL. 8
(2)
1
1 1/2
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
9
12
30
50
90
150
240
350
480
690
910
1190
1600
2085
2714
7563
18900
31500
56700
94500
151300
220600
302500
434900
573500
750000
1008400
1323500
1827700
0.44
0.44
0.56
0.81
1.19
1.56
1.81
1.81
2.31
3.06
4.06
4.56
5.06
5.94
1.62
2.13
2.75
3.25
4.00
4.62
5.50
6.00
6.88
7.75
8.63
9.50
11.00
12.00
1.75
2.25
3.00
3.38
4.25
5.00
5.62
6.44
7.00
7.88
8.75
9.75
---
6000
5500
5000
4400
4000
3500
3000
2700
2500
2200
2100
2000
1900
1800
9500
8500
7800
6800
6200
5500
4600
4100
3900
CONSULT
ENGINEERING
F66
Item (Qty)
Part Number
Description
G4FRB
Sleeves (2)
G4FSEB or
G4FSSB
G4AEB or
G4ASB
9
19
34
55
86
135
195
268
394
526
687
1017
1560
2015
Size
1
1 1/2
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
A
4.56
6.00
7.00
8.38
9.44
11.00
12.50
13.62
15.31
16.75
18.00
20.75
B
3.37
3.91
4.85
6.12
7.18
8.40
9.43
10.61
12.02
13.33
14.96
17.75
C
3.00
3.88
4.81
5.81
6.81
7.84
9.19
10.31
11.44
12.69
13.94
15.75
D
2.31
3.00
4.00
4.62
5.62
6.50
7.50
8.50
9.50
10.50
11.50
13
E
1.69
1.94
2.44
3.03
3.59
4.19
4.75
5.31
6.03
6.91
7.41
8.69
E1
1.56
1.84
2.28
2.9
3.4
3.96
4.43
4.99
5.68
6.11
7.24
8.68
G
0.12
0.13
0.13
0.19
0.19
0.25
0.25
0.31
0.31
0.31
0.31
0.38
H
4.19
4.75
6.00
7.12
8.12
9.38
10.25
11.50
13.00
14.38
17.00
20.00
Note 1. Horsepower,
Torque Capacity and
Parallel misalignment
capacity for sizes 1
through 5-1/2 are based
on 1-1/2 degrees
angular misalignment
per gear mesh and
maximum bore. Sizes 6
and 7 are based on 3/4
degrees angular
misalignment.
Approx. Wt.
(Lbs.) Solid
Bore
9
17
34
55
86
135
195
268
394
526
687
1017
RATINGS
FLEXIBLE HUBS
SIZE
1
1 1/2
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
HP
@
100
TORQUE MIN
RPM
in. lbs.
BORE
12
30
50
90
150
240
350
480
690
910
1190
1600
7563
18900
31500
56700
94500
151300
220600
302500
434900
573500
750000
1008400
0.44
0.44
0.56
0.81
1.19
1.56
1.81
1.81
2.31
3.06
4.06
4.56
MAX BORE
MAX BORE SHALLOW MIN
STD KEY
KEY
BORE
1.62
2.13
2.75
3.25
4.00
4.62
5.50
6.00
6.88
7.75
8.63
9.50
1.75
2.25
3.00
3.38
4.25
4.88
5.62
6.44
7.00
7.88
8.75
9.75
0.44
0.44
0.56
0.81
1.19
1.56
1.81
1.81
2.56
3.06
4.06
4.56
RIGID HUBS
MAX
BORE MAX BORE
STD
SHALLOW MAX RPM
UNBALANCED
KEY
KEY
2.19
2.81
3.50
4.25
4.88
5.63
6.50
7.38
8.38
9.25
10.13
11.25
2.31
3.06
3.75
4.50
5.25
6.13
6.88
8.00
8.88
9.88
11.00
12.25
DETERMINED
MAX RPM
BALANCED
AGMA
CLASS 8
BY BSE
F67
EXPOSED BOLTS
SIZE
SIZE
SHROUDED BOLTS
DIA.GRIP
THD. LENGTH (MAX)
DIA.GRIP
THD. LENGTH (MAX)
SIZE
F-1
1/4-28
1-1/2
F-1
1/4-28
3/4
5/16
F-1-1/2
3/8-24
1-3/8
F-1-1/2; 2
3/8-24
7/16
F-2
1/2-20
2-1/4
1-3/16
F-2-1/2; 3
1/2-20
1-3/16 17/32
F-2-1/2; 3
5/8-18
2-3/4
1-5/8
F-3-1/2; 4; 4-1/2
5/8-18
1-1/2
21/32
F-3-1/2; 4; 4-1/2
3/4-16
3-1/4
2-1/16
F-5
3/4-16
F-5; 5-1/2
7/8-14
4-1/4
2-3/4
F-6
7/8-14
3-1/4
1-3/4
F-7
1-14
3-1/2
No.
EXPOSED BOLTS
B.C. DIA
No.
2.875
3.687
4.625
1-21/32
1-7/8
2-3/8
(6)
(8)
(6)
3.750
4.812
5.875
.250
.375
.500
(6)
(8)
(10)
3.750
4.812
5.812
.250
.375
.375
41/64
13/16
13/16
3/16
1/4
1/4
15/16
15/16
1-1/8
5.437
6.437
7.375
2-7/8
3-5/16
3-13/16
(6)
(8)
(8)
7.125
8.125
9.500
.625
.625
.750
(10)
(12)
(12)
7.000
8.000
9.281
.500
.500
.625
1-1/16
1-1/16
1-5/16
5/16
5/16
3/8
3/16
3/16
3/16
1-1/8
1-1/8
1-1/2
8.750
9.750
10.750
4-1/4
4-13/16
5-1/2
(8)
(10)
(8)
11.000
12.000
13.500
.750
.750
.875
(14)
(14)
(14)
10.625
11.750
13.188
.625
.625
.750
1-5/16
1-5/16
1-9/16
3/8
3/8
9/16
3/16
3/16
1/4
1-1/2
1
1-1/8
12.125
13.375
14.625
6
6-11/16
7-3/8
(14)
(14)
(16)
14.500
15.750
18.250
.875
.875
1.00
(16)
14.437
.750
1-9/16
9/16
G1F
G15F
G2F
4-9/16
6
7
3/32
3/32
3/32
9/16
3/4
3/4
G25F
G3F
G35F
8-3/8
9-7/16
11
3/32
3/32
3/32
G4F
G45F
G5F
12-1/2
13-5/8
15-5/16
G55F
G6F
G7F
16-3/4
18
20-3/4
SHROUDED BOLTS
B.C. DIA
S
CD
Dimensions in inches
TB Woods bolt circle meets AGMA 516.01 flexible gear type couplings flange dimensions.
F68
SIZE
B1
G1F
G15F
G2F
3-1/2
4
5
3-13/16
4-1/4
5-11/16
G25F
G3F
G35F
6-1/4
7-3/8
8-5/8
G4F
G45F
G5F
G55F
G6F
G7F
B2
G1
G2
Q1
4-1/8
4-1/2
6-3/8
1-11/16
1-15/16
2-7/16
1/8
1/8
1/8
7/16
3/8
13/16
3/4
5/8
1-1/2
2-1/8
2-5/16
3-1/4
1/16
1/16
1/16
3/32
1/8
1/8
13/32
3/8
13/16
7-1/32
8-1/32
9-3/16
7-13/16
8-11/16
9-3/4
3-1/32
3-19/32
4-3/16
3/16
3/16
1/4
31/32
27/32
13/16
1-3/4
1-1/2
1-3/8
4
4-7/16
5
3/32
3/32
3/32
1/4
3/8
1/2
1-1/32
1-1/32
1-1/16
9-3/4
10-15/16
12-3/8
10-7/16
12
13-23/32
11-1/8
13-1/16
15-1/16
4-3/4
5-5/16
6-1/32
1/4
5/16
5/16
15/16
1-3/8
1-21/32
1-5/8
2-7/16
3
5-11/16
6-11/16
7-11/16
1/8
1/8
3/16
5/8
21/32
11/16
1-5/16
1-23/32
2-1/32
14-1/8
15-1/8
17-3/4
15-11/32
16-17/32
19-1/16
16-9/16
17-15/16
20-3/8
6-29/32
7-13/32
8-11/16
5/16
5/16
3/8
1-17/32
1-23/32
1-11/16
2-3/4
3-1/8
3
8-7/16
9-1/8
10-3/8
3/16
5/32
3/16
1-1/16
7/8
1-1/2
2-9/32
2-9/32
2-13/16
FSL-1
FSL-2
FSL-3
FSL-4
F69
AISE
Size Frame
FMM Number
602 / 802
1-1/2 603 / 803
604 / 804
603 / 803
2 604 / 804
606 / 806
603 / 803
2-1/2 604 / 804
606 / 806
608 / 808
606 / 806
3 608 / 808
610 / 810
612 / 812
608 / 808
3-1/2 610 / 810
612 / 812
614 / 814
610 / 810
612 / 812
4 614 / 814
616 / 816
618 / 818
614 / 814
4-1/2 616 / 816
618 / 818
614 / 814
5 616 / 816
618 / 818
620
616 / 816
5-1/2 618 / 818
620
622
616 / 816
6 618 / 818
620
622
6.00
6.563
7.00
8.063
8.38
9.719
9.44
10.781
11.00 11.938
12.50 13.250
13.62 14.625
15.31 15.844
16.75 17.719
18.00 18.969
B1
6.0000
6.5625
6.5625
7.1667
7.1667
7.6875
7.7188
7.7188
8.3438
8.9688
8.9063
9.5313
9.6563
10.2813
10.1875
10.3125
10.9375
11.0625
10.8750
11.5000
11.6250
12.2500
12.3125
12.2500
12.8750
12.9375
12.9700
13.5900
13.6563
14.8438
14.4688
14.5313
15.7188
16.8438
14.9688
15.0313
16.2188
17.3438
E1
3.88
4.81
5.81
6.81
7.84
9.19
E2
3.00
3.50
3.50
3.50
3.50
4.00
3.50
3.50
4.00
4.50
4.00
4.50
4.50
5.00
4.50
4.50
5.00
5.00
4.50
5.00
5.00
5.50
6.00
5.00
5.50
6.00
5.00
5.50
6.00
6.75
5.50
6.00
6.75
7.25
5.50
6.00
6.75
7.25
1.7485/1.7495
1.998/1.999
1.998/1.999
1.998/1.999
1.998/1.999
2.498/2.499
1.998/1.999
1.998/1.999
2.498/2.499
2.998/2.999
2.498/2.499
2.998/2.999
3.248/3.249
3.623/3.624
2.998/2.999
3.248/3.249
3.623/3.624
4.2470/4.2485
3.248/3.249
3.623/3.624
4.2470/4.2485
4.6220/4.6235
4.9970/4.9985
4.2470/4.2485
4.6220/4.6235
4.9970/4.9985
4.2470/4.2485
4.6220/4.6235
4.9970/4.9985
5.8720/5.8735
4.6220/4.6235
4.9970/4.9985
5.8720/5.8735
6.2470/6.2485
4.6220/4.6235
4.9970/4.9985
5.8720/5.8735
6.2470/6.2485
0.13
0.13
0.19
0.19
0.25
0.25
0.31
0.31
0.31
0.31
G1
1.062
1.125
1.125
1.125
1.125
1.25
1.188
1.188
1.313
1.438
1.313
1.438
1.563
1.688
1.500
1.625
1.750
1.875
1.625
1.750
1.875
2.000
1.563
1.938
2.063
1.625
1.938
2.063
1.625
2.063
2.063
1.625
2.063
2.688
2.063
1.625
2.063
2.688
0.125
0.125
0.125
0.250
0.250
0.125
0.530
0.530
0.410
0.285
0.560
0.440
0.310
0.190
0.630
0.500
0.380
0.250
0.780
0.660
0.530
0.410
0.840
0.910
0.780
1.220
1.310
1.190
1.630
1.190
1.440
1.880
1.440
0.810
1.470
1.910
1.470
0.840
KEYWAY KEYWAY
WIDTH
HEIGHT
0.500
0.500
0.500
0.500
0.500
0.500
0.500
0.500
0.500
0.750
0.500
0.750
0.750
0.750
0.750
0.750
0.750
1.000
0.750
0.750
1.000
1.250
1.250
1.000
1.250
1.250
1.000
1.250
1.250
1.500
1.250
1.250
1.500
1.500
1.250
1.250
1.500
1.500
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.375
0.375
0.250
0.375
0.375
0.375
0.500
0.375
0.375
0.500
0.375
0.375
0.500
0.750
0.375
0.500
0.750
0.750
0.375
0.500
0.750
0.750
*ALL KEYWAYS SHOWN ARE PARALLEL TO THE TAPER. TAPER IS 1-1/4 INCH PER FOOT ON DIAMETER.
F610
MAX
BORE
STD HP/100
MAXIMUM RPM
HALF RPM
TORQUE UNBALANCED
MAX PARALLEL
MISALIGNMENT
2.13
30
18900
5500
0.060
2.75
50
31500
5000
0.085
3.25
90
56700
4400
0.105
4.00
150
94500
4000
0.115
4.62
240
151300
3500
0.130
5.50
350
220600
3000
0.150
6.00
480
302500
2700
0.175
6.88
690
434900
2500
0.200
7.75
910
573500
2200
0.220
8.65
1190
750000
2100
0.120
Size
G1
G2
H(1)
LEF (5)
1
1 1/2
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
4.56
6.00
7.00
8.38
9.44
11.00
12.50
13.62
15.31
16.75
18.00
20.75
3.56
4.06
5.06
6.34
7.47
8.69
9.91
11.13
12.59
14.34
15.31
18.00
3.00
3.88
4.81
5.81
6.81
7.84
9.19
10.31
11.44
12.69
13.94
15.75
2.31
3.00
4.00
4.62
5.62
6.50
7.50
8.50
9.50
10.50
11.50
13.00
1.69
1.94
2.44
3.03
3.59
4.19
4.75
5.31
6.03
6.91
7.41
8.69
0.19
0.19
0.19
0.28
0.28
0.31
0.41
0.50
0.53
0.53
0.50
0.63
0.13
0.13
0.13
0.19
0.19
0.19
0.31
0.38
0.38
0.38
0.38
0.50
.031
.031
.031
.047
.047
.063
.047
.063
.078
.078
.063
.063
4.19
4.75
6.00
7.12
8.12
9.38
10.25
11.50
13.00
14.38
17.00
20.00
0.13
0.13
0.13
0.19
0.19
0.25
0.19
0.25
0.31
0.31
0.25
0.25
Approx.
Parallel
Wt. (Lbs.)
Misalignment
Solid
Capacity (4)
Bore
0.06
0.06
0.09
0.11
0.12
0.13
0.15
0.18
0.20
0.22
0.12
0.14
9
19
34
54
80
130
190
250
380
520
650
950
RATINGS (4)
FLEXIBLE HUBS
SIZE
HP @
RPM
TORQUE
in. lbs.
MIN
BORE
MAX BORE
STD KEY
1
1 1/2
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
12
30
50
90
150
240
350
480
690
910
1190
1600
7563
18900
31500
56700
94500
151300
220600
302500
434900
57350
75000
1008400
0.44
0.44
0.56
0.81
1.19
1.56
1.81
1.81
2.31
3.06
4.06
4.56
1.62
2.13
2.75
3.25
4.00
4.62
5.50
6.00
6.88
7.75
8.63
9.50
MAX RPM
MAX RPM
BALANCED
MAX BORE
AGMA
SHALLOW UNBALANCED
CLASS 8 (2)
KEY
1.75
2.25
3.00
3.38
4.25
4.88
5.62
6.44
7.00
7.88
8.75
9.75
6000
5500
5000
4400
4000
3500
3000
2700
2500
2200
2100
2000
9500
8500
7800
6800
6200
5500
4600
4100
3900
CONSULT
FACTORY
Notes:
(1) H Dimension Clearance to align coupling.
(2) AGMA CLASS 8 balance requires the manufacture
of two special flexible hubs.
(3) When ordering please specify bore diameter with
tolerances for both hubs, keyway sizes, set screws if
applicable, speed, horsepower, application details,
amount of thrust on either or both shafts, and
amount of end float desired.
(4) Horsepower, Torque Capacity and Parallel
Misalignment Capacity for sizes 1 through 5-1/2 are
based on 1-1/2 degrees angular misalignment per
gear mesh and maximum bore. Sizes 6 & 7 are
based on 3/4 degree angular misalignment. Consult
Engineering for greater HP capacity.
(5) Dimension is total end float. (May be modified to suit
customer requirements.)
Part Number
G4FRB
G4FSEB or
G4FSSB
G4AEB or
G4ASB
G4LEF
Description
4F Rough Bore Flex Hubs
4F Sleeve with Exposed Bolts
4F Sleeve with Shrouded Bolts
Hardware and Gasket for 4F with Exposed Bolts
Hardware and Gasket for 4F with Shrouded Bolts
4F LEF Plate
F611
Notes:
(1) When ordering please specify bore diameter with tolerances for both hubs, keyway sizes, set screws if applicable, speed, horsepower, and application details.
(2) Horsepower, Torque capacity, and parallel misalignment capacity for sizes 1 through 5-1/2 are based on 1-1/2 degrees angular misalignment per gear mesh and
maximum bore. Sizes 6 through 9 are based on 3/4 degree angular misalignment. Consult engineering for greater HP capacity.
(3) H Dimension Clearance to align coupling.
(4) AGMA class 8 balance requires the manufacture of two special flexible hubs. Many configurations of F Series couplings are available to fit your unique application.
Consult Woods mechanical application engineers for design.
F612
STOCK SPACERS
For Use With F, MXB, or K100 Series Couplings
Coupling
Size
DBSE
1 1/2
1 1/2
2
2
2
2 1/2
2 1/2
3
3
3 1/2
3 1/2
4 3/8
5
4 3/8
5
7
5
7
5
7
5
7
G15EBX438
G15EBX5
G2EBX438
G2EBX5
G2EBX7
G25EBX5
G25EBX7
G3EBX5
G3EBX7
G35EBX5
G35EBX7
4.25
4.88
4.25
4.88
6.88
4.81
6.81
4.81
6.81
4.75
6.75
8.394
9.024
9.37
10
12
11.25
13.25
12.37
14.37
13.63
15.63
8.37
9
9.37
10
12
11.25
13.25
12.37
14.37
13.63
15.63
MAX
RPM
Approx.
Spacer
weight
5500
5500
5000
5000
5000
4400
4400
4000
4000
3500
3500
9.8
10.7
13.4
14.1
16.6
24
27
29
33
45
51
Other Sizes, DBSEs, and shrouded bolt patterns are Available as Specials.
C Series Spacer couplings are also available, consult factory.
Below is an ordering example of a 2 FSP Coupling
Item (Qty)
Part Number Description
Flex Hub (2)
G2FRB
2 F Rough Bore Flex Hub
Sleeve (2)
G2FSEB
2 F Sleeve with Exposed Bolts
G2EBX5
2 X 5" DBSE Spacer with Exposed Bolts
Spacer (1)
Hardware and Gasket for 2 F with Exposed Bolts
Accessory Kit (2) G2AEB
F613
Deck-Flex Mite
Deck-Flex Mite
Steel
Stainless Steel
RPM
Torque
(in lbs)
HP
Torque
(in lbs)
HP
Torque
(in lbs)
HP
1420
1110
900
630
530
2.2
20.3
25.0
35.3
42.0
360
282
270
254
243
0.6
5.1
7.5
13.8
19.4
240
188
180
169
162
0.4
3.4
5.0
9.2
12.8
100
1150
1750
3500
5000
2 spirolox type
retaining rings
nylon sleeve
2 hubs
Dimensions
Ordering Example
Deck-Flex
3.75
3.38
1.88
2.38
1.62
0.12
Deck-Flex Mite
2.88
2.38
1.31
1.75
1.12
0.12
Deck-Flex Mite
Item (Qty)
Part Number
Description
Sleeve (1)
GDFMS
Hubs (2)
GDFM34
GDFMAK
Deck-Flex
Item (Qty)
Part Number
Description
Sleeve (1)
GDFS
Deck-Flex Sleeve
Hubs (2)
GDF34
GDFAK
No Lubrication
Operation up to 5000 rpm
Light Weight
Can be altered for blind assembly
Nylon couplings operate up to 150F
Misalignment 5 for Deck Flex
3 for Deck Flex Mite
F614
Stock Bores
Bore
Deck-Flex Mite
5/16
3/8
1/2
5/8
3/4
7/8
1
1-1/8
1-1/4
1-5/16
1-3/8
1-7/16
1-1/2
1-5/8
Rough Bore
...
1/8 x 1/16
3/16 x 3/32
3/16 x 3/32
3/16 x 3/32
1/4 x 1/8
1/4 x 1/8
Deck-Flex
Rough Bore
1/8 x 1/16
3/16 x 3/32
3/16 x 3/32
3/16 x 3/32
1/4 x 1/8
1/4 x 1/8
1/4 x 1/8
5/16 x 5/32
5/16 x 5/32
3/8 x 3/16
3/8 x 3/16
3/8 x 3/16
+.000/+.001
RIGID COUPLINGS
Ribbed Type Compression Couplings are recommended for emergency and
regular service on heavily loaded shafts.
These couplings are bored true to shaft size, and the halves are separated during
boring operation to allow for clamping when halves are drawn together. Bolt heads
and nuts are protected by flanges. End flanges are faced square with bore, and
outer diameters are turned.
To facilitate the use of V-belt drives, sufficient space may be left between shaft
ends when mounting the coupling to permit easy replacement of belts.
SECTION
F7
RIBBED
COMPRESSION
NO. 257
BOLTS
Product
No.
Shaft
Size
Max.
RPM
Approx.
Diam.
Length
No.
Size
2571316
257114
2571716
257112
25711116
257134
25711516
2572
2572316
257214
2572716
257212
25721116
25721516
2573
2573316
2573716
257312
25731516
2574716
25741516
1-3/16
1-1/4
1-7/16
1-1/2
1-11/16
1-3/4
1-15/16
2
2-3/16
2-1/4
2-7/16
2-1/2
2-11/16
2-15/16
3
3-3/16
3-7/16
3-1/2
3-15/16
4-7/16
4-15/16
4630
4630
4070
4070
3820
3820
3250
3250
3050
3050
2680
2680
2610
2210
2210
2100
1920
1920
1830
1600
1390
4-1/8
4-1/8
4-11/16
4-11/16
5
5
5-7/8
5-7/8
6-1/4
6-1/4
7-1/8
7-1/8
7-5/16
8-5/8
8-5/8
9-1/16
9-15/16
9-15/16
10-7/16
11-7/8
13-11/16
5-3/8
5-3/8
6-1/8
6-1/8
6-3/4
6-3/4
8
8
8-3/4
8-3/4
9-5/8
9-5/8
10-5/8
11-5/8
11-5/8
12-3/4
13-5/8
13-5/8
14-5/8
16-1/2
18-1/8
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
3/8
3/8
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
3/4
3/4
3/4
3/4
3/4
3/4
7/8
7/8
7/8
1
1-1/8
Wrench(1) Weight
Torque ft.-lb. Lbs.
19
19
45
45
45
45
93
93
93
93
150
150
150
150
150
150
202
202
202
300
474
11
11
18
18
20
20
34
33
38
38
57
54
62
95
95
126
157
157
171
273
395
NOTE: Capacity of Coupling exceeds capacity of shaft based on 6000 PSI Shaft Stress.
(1) Do not lubricate CAP Screws. Other shaft sizes available on a MTO Basis.
Coupling may require balancing to reduce vibration when operating within these speeds.
F71
RIGID COUPLINGS
This coupling is designed to provide a simple method of rigidly connecting two pieces of shafting. The
standard Sure-Grip tapered bushing is used, one on each shaft, to securely clamp the two shafts together.
The precision tapered fit lines up the two shafts. No press or shrink fits are necessary.
Product
No.
Max.
RPM
Maximum Bore
Light (1) Heavy (2) Bushing
Loads
Loads
44SD
44SF
6200
4500
1-13/16
2-3/8
1-7/16
1-7/8
SD
SF
44E
3600
2-15/16
2-1/4
44J
44M
3000
2450
3-13/16
4-3/4
3
3-11/16
J
M*
DIMENSIONS
A
Weight
Including
Bushings
4
5-1/2
6-7/8
8-1/4
4-5/8
5-1/4
6-3/4
11
3/8
1/2
5/8
3/4
1/4
1/4
1/4
1/2
1-13/16
2
2-5/8
4-1/2
11
22
54
122
10
16
1/2
6-3/4
270
F72
USA SALES
INTERNATIONAL SALES
Canada
T.B. Woods Canada Ltd.
750 Douro Street
Stratford, Ontario, Canada N5A 6V6
Telephone: 519-271-5380
FAX: 519-271-3094
Germany
Berges electronic GmbH
Industriestrae 13
D-51709 Marienheide, Germany
Telephone: 49-2264-17-0
FAX: 49-2264-17-126
India
TB Woods (India) Private Limited
No. 27A, 2nd Cross
Electronic City, Hosur Road
Bangalore, 561 229 India
Telephone: 91-80-8520-123
FAX: 91-80-8520-124
Italy
Berges electronic s.r.l
Via Zona Industriale, 11
I-39025 Naturno, Italy
Telephone: 39-0473-67-1911
FAX: 39-0473-67-1909
Mexico
Industrial Blaju S.A. de C.V.
Oriente 237 No. 171
Colonia Agricola Oriental
08500 Mexico, D.F. Mexico
Telephone: 52-55-55-58-16-20
FAX: 52-55-57-56-06-74
FC 12/03-10M