Documente Academic
Documente Profesional
Documente Cultură
Pipe Size and Weight: Pipe Grade: Range: Tool Joint: New (Nominal) 5.000 0.362 4.276 17.932 712,100 74,100 59,300 17,105 15,672
5.000" 19.50ppf 0.362" wall IEU S-135 2 6.625" X 3.250" NC50 New (Nominal) 5.275 19.635 14.360 5.708 11.415 API Premium 4.154 18.514 14.360 4.476 8.953
Pipe Body 95% RBW 4.964 0.344 4.276 16.968 673,800 70,000 56,000 18,571 14,292 90% RBW 4.928 0.326 4.276 16.012 635,900 66,000 52,800 17,593 12,892 Premium 4.855 0.290 4.276 14.121 560,800 58,100 46,500 15,638 10,029
OD (in) Wall Thickness (in) Nominal ID (in) Calculated Plain End Weight (lbs/ft) Tensile Strength (lbs) Torsional Strength (ft-lbs) 80% Torsional Strength (ft-lbs) Burst Pressure (psi) Collapse Pressure (psi)
Cross Sectional Area of Pipe Body (in2) 2 Cross Sectional Area of OD (in ) Cross Sectional Area of ID (in2) 3 Section Modulus (in ) Polar Section Modulus (in3)
Notes: Pipe Properties are calculated based on uniform OD and wall thickness New = 100% RBW. Premium = 80% RBW Burst Pressure for New based on 87.5% RBW per API
Tool Joint 120,000 psi Material Yield Strength NC50 (4-1/2" IF)
OD (in) ID (in)
6.625 3.250
Drill Pipe Assembly with Grant Prideco NC50 Conventional Connection New
(New guaranteed 95% RBW Pipe with IPC)
Pin Tong Length (in) Box Tong Length (in) *Torsional Strength (ft-lbs) Max Recommended Make-up Torque (ft-lbs) Min Recommended Make-up Torque (ft-lbs) Tensile Strength at Max Recommended MUT (lbs) Tool Joint/Drill Pipe Torsional Ratio (New Pipe) Tool joint/Drill Pipe Torsional Ratio (Premium Pipe) Balance OD (in) Minimum OD for Premium (in)
9.0 12.0 51,200 30,700 25,600 1,133,400 0.69 0.88 6.390 6.313
Adjusted Weight (lbs/ft) Approximate Length (ft) Fluid Displacement (gal/ft) Fluid Capacity (gal/ft) Fluid Capacity (bls/ft) Drift Size (in) Max Upset OD (in)
0.71 0.0169
*Connection torsional strength is less than 80% pipe body torsional strength
Notes: The Drill Pipe Assembly adjusted weight, capacity and displacement calculations account for the adjusted ID in the manufacture of 95% RBW guaranteed pipe with 0.009" internal plastic coating. These values may vary with actual values due to pipe body mill tolerances, internal plastic coating tolerances, and other factors. New pipe guaranteed to 95% RBW will have a smaller ID (4.218'') than new pipe guaranteed to 87.5% RBW
Elevator capacity based on assumed Elevator Bore, no wear factor, and contact stress of 110,100 psi A raised elevator OD increases elevator capacity without affecting make-up torque
The technical information contained herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT. JCT12-06-11
TorqueTensionGraph
Connection:NC50(6.625(in)ODX3.250(in)ID)SMYS=120,000(psi) PipeBody:80%InspectionClass,5.000(in)OD,0.362(in)wallthickness,S135PipeGrade (safetyfactor=1.0)
1,400,000
PipeBodyinCombinedLoading
PipeBodyYieldat80% InspectionClass
1,200,000
ConnectionPerformance(basedonMUT)
ToolJointYield 1,000,000 ToolJointShoulderSeparation TJOperationalLimit(RecMUT)
Tens sion(lbs)
TJOperationalLimit(MinMUT) 800,000
600,000
400,000
200,000
Torque(ftlbs)
ConnectionWearforNC50(6.625(in)ODX3.250(in)ID)
MaterialSMYS(specifiedminimumyieldstrength)=120,000(psi)
60,000
50,000
40,000
Connection
TorsionalStrength
T Torque(ftlbs)
RecommendedMUT
30,000
MinimumMUT
PipeBody
20,000
80% ofPremiumPipe BodyTorsionalStrength
PipeBody:5.000(in)OD,0.362(in)wall thickness,S135PipeGrade
10,000
ToolJointOD(in)