Documente Academic
Documente Profesional
Documente Cultură
Tham)
MEASUREMENTS
MEASUREMENTS
STORAGE or DISPLAY
ANALOG CONTROLLERS
MEASUREMENTS
ANALOG CONTROLLERS
SETPOINTS
1 of 18
CHEMICAL PROCESS
PROCESS COMPUTER
Scheduling Computer
Optimising Computer
Optimising Computer
Supervisory Computer 1
DDC Computer 1
Supervisory Computer 2
DDC Computer 2
Hierarchical Computer Based Operation We are interested in the use of computers to control process plants, within either a DDC or Supervisory control framework. The principles of controller design are identical in both cases. Typical scenarios where computer based process control may be beneficial are: Plants with large throughput - because utilities consumption is approximately proportional to throughput, a small improvement can result in large savings Plants subject to frequent upsets - some plants requires quick responses to process upsets that operators can not provide Complex plants -some processes are too complex for operators to deal with the relationships between process variables and hence are unable to determine the best operating conditions, and maintaining consistent operation is difficult Batch processes - some batch processes require frequent cycling or changes in product specification, and computer control can increase production rate and decrease labour cost
2 of 18
Introduction to Digital Control ( 2005 M. Tham) New processes - in plants with 40-50 control loops, a DCS may prove to be cheaper than an equivalent analog system. SAMPLED DATA SYSTEMS Because of the nature of digital devices, signals from plant have to be converted into a suitable form before it can be transferred for processing by a computer. Similarly, signals generated by a computer must be presented in a form suitable for receipt by the plant. The important pieces of hardware that achieve these tasks are the: sampler analog-to-digital converter (ADC) digital-to-analog converter (DAC) signal hold devices The Sampler The sampler is essentially a switch, operating usually at fixed intervals of time. When the 'switch' closes, it grabs or samples the output of the transmitting device. It then transfers the sampled signal to a receiver. The sampler can operate on both continuous or discrete signals. Thus if the source signal is continuous, the output of the sampler is a series of pulses, and the magnitude of each pulse is equal to the magnitude of the continuous signal at the instant of sampling as shown in the figure below.
Ts
Ts Ts Ts
CONTINUOUS SIGNAL
SAMPLING AT Ts INTERVALS
SAMPLED SIGNAL
ADCs and DACs ADCs converts sampled voltage or current signals to their binary equivalent while DACs converts binary signals to continuous signals such as voltages or currents. These converters provide the interface between a computer and the external environment. Signal Hold Devices The output of a sampler is a train of pulses, regardless of whether the source is continuous or discrete. Thus the output of a computer after digital-to-analog conversion is also a train of pulses. If this is a control signal, then unless the device receiving this signal, say a pump or valve, has integration capabilities, then the process will be driven by pulses. This is obviously not acceptable. So, in process control applications, the signal from the DAC is always 'held' using hardware known as signal hold devices. The 3 of 18
Introduction to Digital Control ( 2005 M. Tham) most common is the Zero-Order-Hold, where each pulse is held until the next pulse comes along, that is:
Ts COMPUTER SAMPLING AT Ts INTERVALS
Ts
SAMPLED SIGNAL
Ts
Ts
ZEROORDER HOLD
HELD SIGNAL
Result of Zero-Order-Hold MATHEMATICS OF SAMPLED DATA SYSTEMS Before proceeding into a discussion on digital controller design, the mathematical tools required will first be covered. The design and analysis of continuous time control systems are usually done using Laplace Transforms, simplifying tremendously, the solution of equations involving time-differentials. Laplace Transforms are therefore continuous transforms. There are two routes to the design and analysis of Digital Controllers. One is to approximate the Laplace operator s to derive difference equations while the other is to use a variant of the Laplace Transforms that is applicable to sampled data systems. These are respectively known as: a) Approximation of differentials b) z-Transforms Approximation of Differentials The use of this technique has its roots in numerical integration, and the two commonly used approaches are: backward difference method bilinear transformation a) Backward Difference Method Starting in the Laplace domain, the Laplace operator s is replaced by a first order difference operator, i.e. s where (1 z 1 ) = t Ts
x ( t ) = x ( t ) x ( t Ts ) ,
4 of 18
't' denotes current time, and the term z 1 is regarded as a time shift operator. The index indicates how many integer multiples of the sampling interval is involved in the time shift, with the sign of the index denoting whether it is a forward (plus sign) or backward (minus sign) shift. For example, z n x(t ) = x(t nTs ) or z n x (t ) = x (t + nTs ) To simplify notation, this can be written as z n x (t ) = x (t n) or z n x (t ) = x (t + n) that is, the sampling interval is treated as a 'unit' of time. Since the Laplace operator s is equivalent to the differential operator
d in the time domain, it dt should be obvious that the backward difference method is the well known Euler's approximation to a differential. As such, the use of this approximation suffers from the same accuracy limitations. The sampling interval must be sufficiently small for accurate conversion from the continuous time domain to the discrete time domain. A more forgiving conversion, especially with high order systems, is the Bilinear Transform.
b) Bilinear Transform The Bilinear Transform is also known as Tustin's Rule as well as the more familiar Trapezoidal Rule used in numerical integration. Here, the Laplace operator s is replaced by: 2(1 z 1 ) s Ts (1 + z 1 ) where the z 1 term has the same meaning as before. Using this transformation, the sampling interval can be much larger, although the ensuing algebraic manipulations become more tedious. The benefit of using this transformation is only obvious with high order systems that have poles of quite different magnitudes. Example: As an example, consider a first-order ODE, relating some output y(t) to an input u(t),
5 of 18
Introduction to Digital Control ( 2005 M. Tham) a) using the backward difference method,
y (t ) = u( t )
K 1 z 1 1 + Ts
Ts + (1 z 1 )
KTs
T y (t 1) + s Ku(t ) y (t ) = Ts + Ts +
b) using the Bilinear Transform, y (t ) = u( t ) KTs (1 + z 1 ) KTs (1 + z 1 ) K = = 2 1 z 1 Ts (1 + z 1 ) + 2 (1 z 1 ) (Ts + 2 ) + ( Ts 2 ) z 1 1+ Ts 1 + z 1
i.e. y (t ) =
Therefore, given the Laplace transfer function of a continuous system, the application of either approximation method will quickly yield discretised models. Both methods are useful in that any continuous time controller design may be quickly discretised using either conversion techniques.
The z-Transform
Here we consider the most commonly used tool for the analysis of sampled data systems. Suppose we sample a continuous time variable f(t). Because the sampled signal exists only at the sampling instants, the sequence of pulses can be represented mathematically as:
f (t ) for n = 0,1,2,... f (nTs ) = otherwise 0
Again, to simplify notation, let the sampled sequence be denoted by f * (t ) . Now the Laplace transform of f(t) is defined as:
F ( s) = f (t )e st dt
0
Since the sampled signal f * (t ) is a subset of f(t), we can also apply the Laplace transform to it:
6 of 18
F ( s) = f * (t )e st dt
* 0
Since f * (t ) only exists at sampling instants, this means that we can replace the integral with a summation, that is,
F ( s) = f (t )e dt = f (nTs ) e snTs
* * st 0 n=0
This is the definition of the z-transform of a continuous time signal f(t) sampled with a sampling interval of Ts, i.e.
Z{ f ( t )} = F ( z ) = f ( nTs ) z n
n=0
Thus, the z-transform is merely the Laplace Transform of a sampled data sequence and as such, inherits many of the properties of the Laplace Transform.
Properties
Some of the more important properties of the z-transforms are as follows: a) Linearity The z-transform is a linear transform. That is, given constants a and b and time variables f(t) and g(t):
Z {af (t ) + bg (t )} = aZ { f (t )} + bZ { g (t )} = aF ( z) + bG( z)
b) z-transforms of time delays If f(t-kTs) is f(t) delayed by k sampling intervals (k is an integer), and f(t) = 0 for t < 0, then the z-transform of f(t-kTs) is given by: Z { f (t kTs )} = z k F ( z) c) Final Value Theorem This theorem allows the calculation of the final value of a z-transformed function and is stated as:
lim f (t ) = lim(1 z 1 ) F ( z)
t z1
7 of 18
The mapping from the s-plane to the z-plane is accomplished through the relationship z = e sTs This function maps the whole of the left side of the s-plane to a unit circle on the z-plane/
s-plane z-plane
z-transform
In the case of Laplace transfer functions, systems are stable if they do no possess poles on the right half of the s-plane. In the case of sampled data systems, they are stable if they do not possess poles that lie outside the unit-circle in the z-plane.
Example z-transforms
Thus Z { f (t )} = F ( z ) = f (nTs ) z n
n=0
That is,
which is an infinite series, illustrating that the z-transforms operates on an infinite sequence. Fortunately, there is also a 'closed-form' equivalent, as it can be shown that
z 1 1 + z 2 +K+ z n +K = 1 = 1 + z z 1 1 z
8 of 18
Introduction to Digital Control ( 2005 M. Tham) b) z-transform of an exponential decay The time function in this case is: f ( t ) = exp( t / ) Thus F ( z ) = exp( nTs / ) z n = 1 + exp( Ts / ) z 1 + exp( 2Ts / ) z 2 +K
n=0
which is another infinite series. Again the closed-form solution is available and can be verified by long division to be:
F ( z) = z 1 1 = z exp( Ts / ) 1 exp( Ts / ) z
Inversion of z-transforms
Like Laplace transforms, z-transforms can be inverted back into the time domain. Given a transfer function, we can either apply long division to obtain the series form of the sampled signal or make use of the tables. The first is simple but tedious and the result may not be suitable for further analysis. Thus tables are often used. In this case, the transfer function is factored into lower order components using partial fraction expansion, and tables are used to look up the corresponding time functions of each component. The final result is obtained by adding up these individual time function. However, due to the nature of the problem, it is not often that z-transform functions need to be converted back to the time domain. Given the range of simulation tools available nowadays, it is usually simpler to simulate the response of the discrete system to enable visualisation of response characteristics.
Relationship to Approximation Methods
With both the backward difference and bilinear transform discretisation methods, a stable continuous system will map to a stable discrete system, with stability in the discrete domain meaning that there are no system poles that lie outside the unit circle in the z-plane. However, the manner in which the mapping to the z-plane occurs is very different. a) Backward difference Noting that z = e sTs , then the first-order series expansion will give z 1 = exp( sTs ) 1 sTs s = 1 z 1 Ts
Thus, the backward difference discretisation method is a first order series approximation to the z-transform and this discretisation maps the left-half of the s-plane to a circle of radius on the right half of the z-plane.
9 of 18
1 z 1 z 1 = Ts zTs
0. 5
b) Bilinear Transform If we use the first order Pade approximation for z-1 instead of a first-order series approximation, then Ts s 1 2 s = 2 (1 z ) = exp( sTs ) T Ts (1 + z 1 ) 1+ s s 2 1
z 1
The mapping from the s-plane to the z-plane is shown in the following diagram.
s-plane
s 2 (1 z 1 ) 2 ( z 1) = Ts (1 + z 1 ) Ts ( z + 1)
z-plane
Like the z-transform, the bilinear transform maps the left-half of the s-plane to the entire unit circle in the z-plane. In this sense, it is a better approximation to use, although it still does not preserve the frequency response characteristics of the original z-transform.
10 of 18
The manipulation of block diagrams of sampled data systems are very similar to that for block diagrams of systems expressed in the Laplace domain. However, because of the presence of samplers, some extra rules have to be adhered to. Consider a continuous process under digital control via the classical feedback framework. The detailed block diagram of this system including the presence of the samplers is,
E(z) W(s)
Ts
U(z) D(z)
Ts
W(z)
CONTROLLER
Y(z)
Ts
Note that the samplers determine the type of signal propagating through the system. Hence the position of the samplers are important. In particular, note that the transfer function between Y(z) and U(z) for the following two systems are different.
System A
U(z) Ts
F(s)
Ts
G(s)
Ts
Y(z)
F(s)
G(s)
Ts
Y(z)
With this system, the relationship between Y(z) and U(z) is given by:
Y ( z) = Z { F ( s)G ( s)}U ( z ) = FG ( z )U ( z)
In general, Z { F ( s)} Z {G ( s)} Z { F ( s)G ( s)} .
11 of 18
Before discussing the design of digital control algorithms, let us consider discrete equivalents of analog controllers. Analog control refers to the design and implementation of controllers in the continuous domain. This includes electronic controllers, which although discrete in nature, implements control by emulating the continuous nature of analog control strategies. A typical example is the electronic PI/PID algorithm. There are a number of ways by which this ubiquitous controller can be implemented in discretised form. a) PI/PID Controller Design from the Time domain Consider the ideal PID controller written in the continuous time domain form:
and
KT u( t ) = K c e( t ) + c s Ti
e(i ) +
i=0
K c Td ( e( t ) e( t 1)) + u0 Ts
which is now in the form of a difference equation, suitable for coding in an appropriate programming language. This particular form of the PID algorithm is known as the 'positional' PID controller, because the control signal is calculated with reference to a base level, uo. b) PI/PID Controller Design from the Laplace Domain We can also formulate discrete PID controllers directly from the Laplace domain. Here, the PID algorithm is written as:
U ( s) 1 = Kc 1 + + Td s E ( s) Ti s
Now we can apply either the backward difference or bilinear transform methods to get an equivalent discrete PID controller. Say we apply the backward difference method. Then,
backward difference (1 z 1 ) Ts U ( s) 1 = K c 1 + + Td s u(t ) = e(t ) K c 1 + + Td 1 E ( s) Ts Ti (1 z ) Ti s
12 of 18
This PID controller is different in structure to that obtained from time-domain considerations and is known as the 'velocity' PID algorithm. As opposed to the fixed control reference used in the positional algorithm, here, the calculation of current control uses the previous control value as reference. In essence, the control is calculated as a change, hence the term 'velocity form'. Application of the Bilinear Transform will yield a similar velocity form algorithm, due to the presence of the (1 z 1 ) term in the approximation.
Positional and Velocity PID Algorithms
Although the structures of the positional and velocity PID algorithms appear very different, they are in fact related. The positional algorithm as derived is:
u ( t ) = K c e( t ) +
Kc Ts Ti
e(i ) +
i =0
K c Ts u(t 1) = Kc e(t 1) + Ti
e(i ) +
i =0
t 1
Subtracting this from the original, we end up with the velocity form, i.e.
u(t ) = u(t 1) + K c [e( t ) e( t 1)] + KT K c Ts e( t ) + c d [e(t ) 2e( t 1) + e( t 2)] Ti Ts
a) Commissioning discrete PID Controllers To calculate control, the positional PID requires knowledge of uo, which is some steady-state control output level. This may have implications during commissioning. With the velocity form however, the previous control can be set to any reasonable arbitrary level, and hence commissioning is simpler. b) Integral Windup A more important aspect is the use of a summation to calculate the contribution of the integral term. This can lead to problems leading to a phenomenon known as integral windup, causing long periods of overshoots in the controlled response. This can be caused by a poorly tuned controller or the controller output is overly constrained (for some safety reasons or inappropriately sized final control element say), or a combination of both factors. What happens is this. Say a positive set-point change occurs, and the controlled process has a positive gain. The controller will then try to reduce the error between set-point and output, 13 of 18
Introduction to Digital Control ( 2005 M. Tham) which is initially positive. The integral component will sum these positive errors to generate the necessary integral action. An overshoot occurs, whereupon the errors become negative. However, the direction of the control signal will not change to compensate if the sum of previously positive error dominates, in which case the overshoot becomes prolonged. The direction of control action will change only when the contribution of negative errors cancels the accumulated positive errors sufficiently. This phenomenon is illustrated in the following figures, where the set on the right has a tighter limit on the control signal (1.5 instead of 2) and shows clearly, the effects of integral windup.
With the velocity PID algorithm, because it does not make use of a sum of errors to generate integral action, the problem of integral windup will not occur, even if the control signal is constrained. This difference is illustrated in the following set of figures which shows the performances of the positional and velocity PID algorithms applied to the same process, and constrained by the same control limits.
14 of 18
1.2
1.2
0.8
0.8
0.6
0.6
0.4
0.4
0.2
0.2
50
100
150
Sample number
Sample number
Controlled output
1.5
1.5
Controlled output
Control signal
0.5
0.5
Control signal
50
100
150
50
100
150
Sample number
Sample number
Control signal
Control signal
c) Proportional and Derivative Kicks Kicks refer to a sudden and large change in control signal and is usually the result of a sudden change in either the setpoint or a disturbance. Compared to the positional PID, the velocity PID is quite susceptible to kicks. In the velocity PID, the proportional and derivative components act on differenced error signals. In particular, the derivative component acts on a doubly differenced error signal. These error differences can be significant when a large step change in set-point is introduced and will cause the controller to compute large changes in control manipulations which may perturb the controlled process excessively. Fortunately, because ofKicks can be mitigated by making a slight modification to the velocity PID algorithm. In the derivation of the velocity algorithm, assume that set-point remains constant for at least 2 sampling instants, i.e.
w( kT ) = w( kT T ) = w( kT 2T ) . Then,
15 of 18
Introduction to Digital Control ( 2005 M. Tham) e( kT ) e( kT T ) = w( kT ) y ( kT ) w( kT T ) + y ( kT T ) = y ( kT ) + y ( kT T ) Using this in the formulation of the velocity PID controller lead to the so-called PYID algorithm, viz.
u( kT ) = u( kT T ) K c [ y ( kT ) y ( kT T )] + Kc T Kc D e( kT ) [ y( kT ) 2 y( kT T ) + y( kT 2T )] T I
The difference in performances between the velocity PID and PYID controllers are shown in the figures below. Note that both controllers were implemented with the same settings.
Velocity PID
1.5 1.5
PYID
0.5
50
100
150
Sample number
Sample number
Controlled output
3.5 3.5
Controlled output
2.5
2.5
Control signal
Control signal
0 50 100 150
1.5
1.5
0.5
0.5
50
100
150
Sample number
Sample number
Control signal
Control signal
When the setpoint change occurred, the signal from the velocity PID controller went beyond 3 whereas the PYIDs control signal was significantly smaller. These are reflected in the respective controlled output responses where the overshoot from the PYID controlled process is smaller. Both closed loops have almost identical settling times.
16 of 18
d) Controller tuning All the tuning procedures for continuous time PID controllers apply. These range from the empirical Ziegler-Nichol ultimate gain method, to the recipe based integral of error criteria. With recipe based methods, a factor of 0.5Ts is usually added to the process dead-time to account for the delay caused by the sampler.
Choice of Sampling Interval
Another important aspect in sampled data control systems is the choice of sampling intervals. With electronic controllers that emulate continuous time algorithms, this choice is simple: sample as fast as possible. This is because of the approximations that are used to generate the difference equations describing the controllers. Smaller sampling intervals mean that the properties of the underlying controller design will be less distorted, hence more predictable and better performances. A good example is the discretised PID controllers. They perform best when sampling intervals are small. However, too fast a sampling is wasteful of resources. the cost of implementation will increase because more capable components must be installed a DCS typically has many hundreds of input-output channels to administer. The functioning of the DCS will degrade significantly if every control loop is to sample at the highest frequency possible. fast sampling intervals will mean that high frequency components such as noise will also be captured in the signal, and this is not necessarily beneficial to the performance of the control loop. If the sampling interval is too long, then signal loss will occur. An extreme case is the phenomenon known as 'aliasing'. This is a situation whereby the sampled versions of two very different signals are indistinguishable. As illustrated in the figure below, the sampled representation of a step (dotted horizontal line) and a periodic wave are identical.
1.5
0.5
Ts
0 1 2 3 4 5 6
-0.5
-1
-1.5
17 of 18
Introduction to Digital Control ( 2005 M. Tham) Flow loops Level loops Temperature loops 1s 5s 30s to 10 mins.
These are however, merely rough guidelines. The choice of an appropriate sampling interval should be based on the dynamics of the process being controlled. The sampling operation must return the key dynamic characteristics of the process. From experience, a sampling interval of approximately 10% of the dominant time constant works well in practise. The position of the poles and zeros of the discrete transfer functions depend on the sampling interval used. Although this characteristic is not of great significance in PID type algorithms, it becomes important when discrete process models are used directly in the design of digital controllers. We shall cover this in more detail when we discuss model based digital controller design.
18 of 18