Documente Academic
Documente Profesional
Documente Cultură
2:1999
PREFACE
This Standard was prepared by the Joint Standards Australia/Standards New Zealand
Standards Committee SF/43, High Pressure Water Safety.
The purpose of this Standard is to provide manufacturers and users with the minimum
requirements for equipment and associated componetry for high pressure water jetting
systems.
The term ‘normative’ has been used in this Standard to define the application of the
appendix to which it applies. A ‘normative’ appendix is an integral part of a Standard.
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
CONTENTS
Page
2.3 PIPEWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4 PRESSURE VESSELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5 ELECTRICAL EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.6 SAFETY AND PRESSURE RELIEF VALVES (RELIEF DEVICES) . . . . . . 8
2.7 HOT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.8 GUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SECTION 4 HOSES
4.1 CLASS A JETTING SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 CLASS B JETTING SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SECTION 6 MARKING
6.1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.2 PUMPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.3 HOSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.4 ADAPTORS AND END FITTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.5 HOSE ASSEMBLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.6 RE-ENDED AND RETESTED HOSES . . . . . . . . . . . . . . . . . . . . . . . . . . 14
S E C T I O N 1 S C O P E A N D G E N E R A L
1.1 SCOPE This Standard sets out requirements for the design, construction testing,
inspection and safeguarding of high pressure water jetting systems.
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
1.3 APPLICATION This Standard provides requirements for high pressure water
jetting systems with an output capability greater than 800 bar litres per minute and less
than 5600 bar litres per minute (identified as Class A) and systems with an output
capability in excess of 5600 bar litres per minutes (identified as Class B.)
Guidance for safe operation and maintenance of pressurized water jetting systems is not
covered by this Standard but is given in AS/NZS 4233.1.
COPYRIGHT
This is a free preview. Purchase the entire publication at the link below: