Documente Academic
Documente Profesional
Documente Cultură
In partial fulfilment of the requirements of the Final Year Project in Mechanical Engineering for the degree of Baccalaureus in Arte Ingeniaria (BAI) Department of Mechanical and Manufacturing Engineering Trinity College Dublin 2012
Abstract
T-Junction geometry is a very generic flow configuration in industry and one of the greatest problems recognised with this type of geometry is the generation of vibration due to the acoustic excitation of the flow. This is caused by a flow-acoustic coupling in a sound field and is brought about at certain flow rates and T-Junction geometries. A review of past and present literature on the subject is presented in order to understand the context of acoustic resonance in T-Junctions and pipes in general. The factors that affect the future of CFD and whether it is feasible enough to be considered a stand-alone alternative to experimentation are explored. The acoustic resonance is numerically modelled using a commercial CFD package to determine the feasibility of CFD for this complex flow. In order to achieve reasonable accuracy, it was essential to determine the most suitable turbulence model and mesh. A series of tests are carried out in order to assess this. Initial tests revealed that the SST - model was the clear winner for modelling the turbulent flow in this geometry and a meshing scheme using inflation layers produced the most computationally efficient results. Successful modelling of the vortex shedding in a T-Junction was eventually achieved by artificially fluctuating the velocity at the inlets using a sine wave function.
ii
For Sneha
iii
iv
Table of Contents
Abstract ............................................................................................................................. i List of Figures .................................................................................................................vii List of Tables ................................................................................................................... ix Abbreviations ................................................................................................................... x Nomenclature ................................................................................................................... x 1 Introduction.............................................................................................................. 1 1.1 1.2 2 3 Project Background .................................................................................................. 2 T-Junction Geometry ............................................................................................... 4
Literature Review ...................................................................................................... 6 Computational Fluid Dynamics (CFD)................................................................. 15 3.1 3.2 3.3 CFD Strategy ........................................................................................................... 15 Software ................................................................................................................... 15 Turbulence Modelling ........................................................................................... 16 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.4 Introduction ............................................................................................... 16 - Two-Equation Model ......................................................................... 17 SST - Two-Equation Model................................................................. 19 Reynolds Stress Model (RSM).................................................................. 20 Large Eddy Simulation (LES) ................................................................... 21
Turbulence Model Testing .................................................................................... 23 Geometry ................................................................................................................. 27 Meshing ................................................................................................................... 29 Problem Setup......................................................................................................... 32 Analysis and Post-Processing ............................................................................... 34 Mesh Influence ....................................................................................................... 35 Effect of Convergence Criteria ............................................................................. 38 T-Junction with Chamfered Inlets ....................................................................... 40 Rectangular Duct T-Junction (Steady) ................................................................ 41 v
5.5 5.6 6
Rectangular Duct T-Junction (Unsteady)............................................................ 44 Rectangular Duct T-Junction (Unsteady with UDF) ......................................... 46
Conclusion .............................................................................................................. 50
List of References ........................................................................................................... 52 Appendix ........................................................................................................................ 57 T-Junction Geometries ..................................................................................................... 57 Unsteady flow UDF .......................................................................................................... 60
vi
List of Figures
Figure 1.1 Gas and Oil pipelines in Ireland and the UK [2] ................................................. 2 Figure 1.2 Different flow possibilities in a T-junction ........................................................... 3 Figure 1.3 Turbine bypass piping system. (1) Steam turbine isolation valve; (2) Bypass isolation valve; (3) Bypass control valve; (4) T-junction [1] ................................................. 4 Figure 1.4 (b) T-Junction without a transition zone (c) T-Junction with asymmetric transition zone [1] ...................................................................................................................... 5 Figure 2.1 Rectangular duct T-Junction test setup [1]........................................................... 7 Figure 2.2 Flow visualisation arrangement [1] ....................................................................... 7 Figure 2.3 Typical responses for Case A T-Junctions with and without a transition zone [1] ................................................................................................................................................. 8 Figure 2.4 Responses for the four Case A T-Junction geometries [1] ................................. 8 Figure 2.5 Flow-induced acoustic resonance at the safety relief valve (SRV) side branch [7] ................................................................................................................................................. 9 Figure 2.6 The possible outcomes of Howe's equation [10]................................................ 10 Figure 2.7 LES/SI method [14] ............................................................................................... 12 Figure 2.8 Experimental results (solid blue lines) vs. numerical results (dashed red lines) [14] ............................................................................................................................................. 12 Figure 2.9 3D mesh structure in the plane of symmetry and cross-section of the TJunction used in [16]................................................................................................................ 13 Figure 2.10 Contours of Mach number at the plane of symmetry [16] ............................. 13 Figure 2.11 Computations per kilowatt-hour over time [20] ............................................. 14 Figure 3.1 Visualisation of the continuous and discrete domain [21] ............................... 15 Figure 3.2 ANSYS Workbench workflow.............................................................................. 16 Figure 3.3 Residual plots of various turbulence models with a convergence criterion of 1 x 10-3 ........................................................................................................................................... 25 Figure 3.4 Velocity contours of three different turbulence models ................................... 26 Figure 4.1 Primary branch acoustic mode [1] ...................................................................... 27 Figure 4.2 (left) 3D flow in a pipe of cylindrical cross section [43] (right) 2D flow in a pipe of cylindrical cross section at the central axis but is the same for a rectangular duct [44] ............................................................................................................................................. 28
vii
Figure 4.3 (left) Dimensions of T-Junction with cylindrical geometry [1] (right) Table displaying the dimensions and relationships between L and D [1] .................................... 28 Figure 4.4 T-Junction geometry created using ANSYS DesignModeler ............................ 29 Figure 4.5 Two different meshing approaches ...................................................................... 31 Figure 5.1 Bad meshing and resulting y+ values .................................................................... 35 Figure 5.2 A more ideal mesh and resulting y+ values .......................................................... 36 Figure 5.3 Difference in velocity contours between the bad mesh (left) and the better mesh (right) ............................................................................................................................... 37 Figure 5.4 Results of a simulation between convergence criteria of 1 x 10-3 (left) 1 x 10-6 (right).......................................................................................................................................... 38 Figure 5.5 Residual plot for convergence criteria of 1 x 10-6 ............................................... 39 Figure 5.6 Vorticity contours of a T-Junction with chamfer (left) and without (right) .. 40 Figure 5.7 3D velocity profile of the flow in a rectangular duct .......................................... 41 Figure 5.8 Four cases of rectangular geometry T-Junctions based on the template on the left [1] ......................................................................................................................................... 41 Figure 5.9 Velocity swirling vector contour map of the flow in a T-Junction .................. 42 Figure 5.10 Vorticity contours of the flow development in the branch pipe (flow from right to left) ................................................................................................................................ 43 Figure 5.11 Vorticity contours of the four cases. Vortex formation is strongest in the red regions ........................................................................................................................................ 43 Figure 5.12 Normalised acoustic pressure as a function of reduced velocity for the four test cases [1] ............................................................................................................................... 44 Figure 5.13 Velocity plots of the four cases at various locations of the T-Junction ......... 45 Figure 5.14 Oscillation of branch velocity with time............................................................ 47 Figure 5.15 Instantaneous flow structure images and sketches for a complete cycle of Mode A oscillation (VR = 1.65 and f = 118 Hz) [1] ............................................................... 47 Figure 5.16 Velocity plots of the four cases at various locations of the T-Junction (with UDF) ........................................................................................................................................... 48 Figure 5.17 Combined vector and streamline map of regions of recirculation (blue regions)....................................................................................................................................... 48 Figure 5.18 Vorticity (500 1000 s-1) (left) and dynamic pressure (500 1000 Pa) (right) contour maps at different phase angles for Case 1 ............................................................... 49 Figure 6.1 Three different modelling approaches ................................................................. 51 Figure 6.2 RANS vs. LES .......................................................................................................... 51 viii
Figure 0.1 Geometry #1 ........................................................................................................... 57 Figure 0.2 Geometry #2 ........................................................................................................... 58 Figure 0.3 Geometry #3 (Case 1) ............................................................................................ 59 Figure 0.4 Geometry #3 (Case 2) ............................................................................................ 59 Figure 0.5 Geometry #3 (Case 3) ............................................................................................ 59 Figure 0.6 Geometry #3 (Case 4) ............................................................................................ 59
List of Tables
Table 3.1 Iterations required for different turbulence models with a convergence criterion of 1 x 10-3 ................................................................................................................... 24 Table 4.1 Hydraulic diameters calculated for the cylindrical pipe and the rectangular duct ............................................................................................................................................. 33 Table 5.1 Section 5.1 pipe parameters (See Appendix) ....................................................... 35 Table 5.2 Section 5.2 pipe parameters.................................................................................... 38 Table 5.3 Section 5.3 pipe parameters.................................................................................... 40 Table 5.4 Section 5.4 pipe parameters (see Appendix) ........................................................ 41
ix
Abbreviations
CFD DNS LES RANS RSM SFS SIMPLE SMG SST UDF URANS Computational Fluid Dynamics Direct Numerical Simulation Large Eddy Simulation Reynolds-Averaged Navier-Stokes Reynolds Stress Model Sub-filter Scale Semi-Implicit Method For Pressure-Linked Equations Standard Smagorinsky Model Shear Stress Transport User-Defined Function Unsteady Reynolds-Averaged Navier-Stokes
Nomenclature
A D d dh f L LB LM p Q r Re t Cross-sectional area Diameter or height of the transition zone and main pipe Diameter or height of branch pipe Hydraulic diameter Frequency (Hz) Half-length of the transition zone Characteristic length Length of branch pipe Length of main pipe Pressure Volume flow rate Radius Reynolds number Time V VB VM VR y+ y A Velocity Velocity of fluid in the branch pipe Velocity of fluid in the main pipe Reduced Velocity Non-dimensional wall distance First inflation layer height Wavelength Viscosity Kinematic viscosity Density Time step size Time step Vorticity Frequency (rad/s)
S.I. units used throughout. The symbols shown above are valid throughout unless specified otherwise.
Introduction
The basis of this study was motivated by the works of Ziada et al. [1] where the
flow in T-Junctions of various geometry and flow configuration was investigated. This study focuses on modelling the unsteady flow in a T-Junction with a symmetric transition zone using computational methods in order to gauge the feasibility of computational fluid dynamics (CFD) compared to the actual experiment. A certain element of trial-and-error is involved in CFD which raises the question as to whether a solution can be considered as accurate as an actual experiment. Is CFD is a feasible alternative for accurately representing the flow in a T-Junction? What are the difficulties involved and the downfalls of CFD? Does CFD take into account effects such as acoustic vibration? These are some of the questions that the study hopes to answer. All T-Junction geometry created for simulations follow the dimensions of the geometry of the pipes and ducts described in [1]. The flow is to be simulated using an unsteady Reynolds-Averaged Navier-Stokes (URANS) model in ANSYS Fluent, a commercial CFD package. This is explored in greater depth in the section on turbulence modelling. A URANS model is used due to its relatively low computational cost and reasonable accuracy compared to direct numerical simulation (DNS) or models such as the Reynolds stress model (RSM). The remainder of this section will briefly discuss the background of the project, the geometry of the T-junction and some of the physics behind the flow. The following chapter will review the relevant literature in this field. This includes the work has been done and the work that is being done in relation to the coupling of acoustic resonance in fluid flows in a T-Junction. Later, an introduction into turbulence modelling is presented and it concludes upon the model most suited for this simulation. Once all the relevant information has been detailed, the methodology required to carry out the simulations can be described and subsequently, the results can be analysed.
Figure 1.1 Gas and Oil pipelines in Ireland and the UK [2]
Pipe networks are prevalent in any major industry and therefore, many of the components and flow configurations are widespread. One such flow configuration is a T-junction. This is a generic design that allows two flows to converge into one flow or one flow to diverge into two. Depending on the direction of fluid flow, a few different possibilities are possible and are shown in Figure 1.2.
In many such T-junctions, one issue that arises time and time again is the generation of acoustic resonance. This is caused when the sound field generated is coupled with the unsteady separated fluid flow. Resonances cause high noise levels and excessive vibration that can damage pipe networks by overstressing its components as well as cause significant efficiency losses which results in fatigue failure over time. This is a well-documented problem and is often encountered in high-pressure piping systems transporting steam or natural gas. This resonance is caused by unstable flow structures such as free shear layers, jets and wakes. Small vorticity disturbances at the regions of flow separation rapidly grow into vortex-like structures as they travel downstream with the flow [1]. Vorticity is a vector field and is defined as the curl of the velocity as shown below: Where is the vorticity, is the gradient and V is the velocity. When these vortex-like
= V
structures travel downstream within a sound field, acoustic energy is either absorbed or produced. In the case of the T-junction, the excessive creation of acoustic energy causes resonance. Howes work on the dissipation of acoustic energy [2] describes the dissipation of acoustic energy between unsteady vorticity and acoustic fields by the following integral over the fluid volume :
= (V u )d
where is the vorticity, V is the flow velocity, is the density of the fluid and u is the acoustic particle velocity of the sound field. The integral of the instantaneous acoustic 3
power over a complete acoustic cycle may result in either positive or negative acoustic energy. Acoustic resonances will only be excited by separated flows if the integral of the above equation is positive over a complete acoustic cycle. [1]. Various studies have used Howes equations to understand and explain the flow-sound interactions in various flow configurations eg. [3]. A study conducted by Ziada et al. [1] was based on a specific vibration problem involving a steam turbine bypass piping system in a power plant. It was observed that fluid flowing through the valves at certain flow rates induced strong vibrations in the bypass piping downstream of the valves (highlighted in red in Figure 1.3). The mechanism of this failure was found to be the unsteady coupling of vortex shedding at the mouth of the valve along with the side branch acoustic resonance.
Figure 1.3 Turbine bypass piping system. (1) Steam turbine isolation valve; (2) Bypass isolation valve; (3) Bypass control valve; (4) T-junction [1]
pipe exiting (or downstream of) the T-Junction will be called the main pipe and the expanded portion of the T-junction will be called the expansion zone or the transition zone. This terminology is exactly the same terminology used by Ziada et al. [1, 3] in their experiments. Alternative T-Junction geometry have also made an appearance in their experiments [1, 3] with a range of dimensions and flow directions. One such example is a T-Junction without a transition zone where the branch pipes and the main pipe are of the same diameter. This is the simplest possible T-Junction geometry as there is no transition zone. Another variation of the T-Junction is where the transition zone is asymmetric about the centreline of the main pipe (Figure 1.4).
Figure 1.4 (b) T-Junction without a transition zone (c) T-Junction with asymmetric transition zone [1]
The flow in each geometry is different and the addition of a transition zone affects the flow and sometimes induces resonance. Furthermore, symmetry or asymmetry of the transition zone influences the flow in the main pipe and the behaviour of the resonance previously mentioned.
Literature Review
This basis for this project branched out from the work of Ziada et al. [1, 3] which
investigated the flow-acoustic coupling between separated flow in a T-Junction at the lowest acoustic mode. These works focused on physically modelling the flow in a TJunction. The premise was that acoustic resonances are excited due to the coupling between an acoustic mode and an unsteady flow. Acoustic resonances can lead to excessive noise and dangerous levels of vibration. This vibration is caused as a result of small vorticity perturbations growing rapidly into vortex-like structures at the flowseparation region. The convection of these vortex-like structures within a sound field results in the production or absorption of acoustic energy. This is a well-recognised and documented phenomenon in industry especially with gases and steam in high-pressure piping systems. Chen and Florjancic [4] identified the source of failure in many safety relief valves to be flow-induced vibration. The mechanism of this vibration was found to be the unstable coupling of acoustic resonance and vortex shedding. The U.S. Nuclear Regulatory Commission reported the failure of a steam dryer in Quad Cities nuclear power plant where flow-induced vibration caused damage to components and supports for the main steam and feedwater lines [5]. The present study in [1], although instigated by a specific vibration problem of a steam turbine bypass piping system, addresses a generic T-Junction flow configuration found commonly in industry. It was found that at certain flow rates, strong vibrations were experienced by the piping. The experimentation in this study was carried out on TJunctions with an expansion zone so that the diameters of the two inlet pipes can be matched. Two separate types of pipes were used. The first was a cylindrical pipe (Case A) and T-Junction whereas in the second case a rectangular duct (Case B) was used. The majority of the data obtained was from the rectangular duct case as flow visualisation was only conducted in this case. Case A mainly focused on obtaining data using 6
commercial piping and geometries such as using PVC piping and chamfered T-Junction inlets. Figure 2.1 and Figure 2.2 shows the experimental setup for Case B. Case B was used for flow visualisation because it allowed for the capture of reasonably clear images due to the two-dimensional nature of the T-Junction (flat side walls).
The results of the study revealed that in Case A, the onset of acoustic resonance was noticeable at a VM between 25 m/s and 45 m/s and a significantly stronger resonance was observed at VM = 65 m/s at ~118 Hz. But perhaps what was most interesting was that acoustic resonance was only present in T-Junctions with a transition zone as opposed to T-Junctions without a transition zone (Figure 2.3. The data for the T-Junction without a transition zone comes from a previous study from Ziada et al. [3]. 7
The results of Case B also show a similar trend as in Figure 2.3 (Figure 2.4) where little to no resonance was observed when the transition zone was omitted.
Figure 2.3 Typical responses for Case A T-Junctions with and without a transition zone [1]
Figure 2.4 Responses for the four Case A T-Junction geometries [1]
The main finding here was that the flow excitation is caused by the instability of the shear layers separating from the step expansions at the inlets of the T-Junction. This is also mentioned in a previous study by the same author [3]. Experiments by Michalke [6] have shown that shear layers are unstable relative to disturbances within a certain 8
frequency range. It was also found that introducing geometrical asymmetry in the transition zone produced little effect on the intensity of the acoustic resonance. The study provides a guideline range of velocities that are outside the resonance range for a range of L/D ratios. The previous study by Ziada et al. [3] was a precursor to the current study as it laid the foundations for most of the experimentation. The T-Junctions tested in this case did not have an expansion zone and the results were similar to those in case 4 for the rectangular duct in [1]. In the context of this project, the works of Ziada et al. [1, 3] have been the most influential. Okuyama et al. [7] investigated the acoustic resonance at the entrances to one or two side branches. The context here was similar to the case of the Quad Cities Unit 2 Nuclear Power Plant [5]. The geometry of the pipes used here can be compared to a TJunction in some respects, but different to [1] in terms of flow directions and dimensional proportions. Three pipe configurations were used: a single branch pipe (Figure 2.5), coaxial branch pipe and the final case where the branch pipes were in tandem.
Figure 2.5 Flow-induced acoustic resonance at the safety relief valve (SRV) side branch [7]
It was found that as the ratio of the cross-sectional area of the main pipes and the branch pipes decreased, the amplitude of resonance increased. This was because the radiation loss from the branch pipe to the main pipe increased at higher values of the 9
cross-sectional ratio. This is one of the reasons why the vibration due to acoustic resonance was relatively much stronger in [1, 3] . Karlssons [8] doctoral thesis provides rigorous insight into the aeroacoustics of duct branches in the context of silencers in cars. It focuses heavily on the acoustics and it concludes upon the practical importance of the work when it comes to designing complex flow duct networks. The study was motivated by the general concern of global warming and the interest of developing new silencer concepts that can sufficiently reduce exhaust noise in an internal combustion engine as well as being as compact as possible and having minimal energy losses. The research focused on minimising the flow losses in flow expansions (such as an expansion zone in a T-Junction), contractions and reversals. Howes equation [2] (see section 1.1) is mentioned in [8] to determine whether acoustic energy is produced or absorbed. If the equation is positive, sound is generated; if the equation is negative, sound is dissipated (Figure 2.6). Acoustic resonances will only be generated by separated flows if the integral of Howes equation is positive over a complete cycle. Howes equation has been used by numerous authors [9-11] to describe the effects of flow-sound interaction mechanisms for various flow configurations such as deep cavities exposed to grazing flows.
Karlssons work [8] was also relevant to this project because it investigated the use of steady simulations using CFD to interpret the aeroacoustic phenomena. He mentions that steady-state CFD simulations are a computationally effective tool for 10
rapid design cycles and this is indeed true as CFD cuts down on expensive and time consuming experimentation. The contour maps generated from the simulations are surprisingly similar to the results obtained in the project in terms of the flow pattern and behaviour. However, it is interesting to note that the - model is used here. The - model models free stream flows with a reasonable amount of accuracy but its quite a bad option to model flows at walls and boundary layers. The SST (Shear Stress Transport) - model is a much better option in comparison as it combines the strengths of the - model at the near-wall and boundary layers but avoids oversensitivity in the free stream because as it switches to - formulation here. The section 3 on computational fluid dynamics explores the strengths and weaknesses of different turbulence models. The above research is of practical important in the design of complex flow duct networks as it provides as formalism for including flow-acoustic interaction effects in linear multiports with the goal of measuring the amplification and reducing the incident sound and also predicting non-linear phenomena such as whistling. This can be related to this project as vortex shedding at the inlet of the T-Junction (which can be considered a sharp-edged orifice) is very closely related to whistling. Other works such as [12] and [13], both by Karlsson and Abom investigated aeroacoustics in T-Junctions using a new method that they proposed and developed a quasi-steady model to describe the acoustic scattering properties in a T-Junction in the low Strouhal number limit respectively. [13] is applicable in the design of automotive intake and exhaust systems and the basis for this is from Karlssons doctoral thesis [8]. Whistling of pipes and orifices and experimentally and numerically investigated in [14]. The numerical approach involved using Large Eddy Simulation (LES) with an acoustic signal analysis. LES is a very computationally expensive but a highly accurate turbulence model and is explored in greater depth in section 3. The LES simulation was coupled with a System Identification (SI) method for the acoustic signal analysis. This was termed the LES/SI method and is shown in Figure 2.7. The solver used in this study was AVBP developed by CERFACS [15]. This study was interesting because it involved 11
numerical simulation as opposed to most other research in the area relying on experimentation. The numerical results are then compared with the experimental results and it shows how a numerical simulation can almost be as accurate as actual experimentation (Figure 2.8) which once again reinforces Karlssons conclusion regarding CFD simulations [8]. Another important note in [14] is regarding the y+ values used to model the flow. Low y+ values are used in the simulation as it was important to generate a mesh that was not too coarse. Section 5.1 of this thesis on the influence of meshing on the solution provides more insight regarding y+ values and the accuracy of the solution.
Figure 2.8 Experimental results (solid blue lines) vs. numerical results (dashed red lines) [14]
12
A study by Prez-Garcia et al. [16] investigated the internal compressive flow in T-Junctions in much greater detail from a numerical point of view than the studies previously mentioned here. The study compared a range of turbulence models in order to determine which was best suited for the problem at hand. The methodology used closely resembles the methodology used in this project. Similarities include the choice of turbulence models and the mesh generated (Figure 2.9) (see section 4.2 for the mesh used in this project). One of the conclusions of [16] was that the SST - model agreed best with the experimental and reference data. A similar conclusion on the choice of turbulence models is reached in this project as well. A contour map of Mach numbers at the plane of symmetry obtained in [16] was almost exactly the same as the contour maps of velocity obtained in this project (section 5.2).
Figure 2.9 3D mesh structure in the plane of symmetry and cross-section of the T-Junction used in [16]
13
Numerous other studies have been conducted in the field for flow-acoustic coupling and vibration in pipes. Examples of this include the works of Tonon et al. [17, 18]. However, the push towards numerical simulations of flows is a relatively recent development. Prez-Garcia et al. [16] mention that the computational time required for each simulation was about a week on a Compaq HPC160 16 1 GHz processor. As computational technologies advance, the computational time for simulations reduces and numerical simulations become a much more feasible option. Moores law, in practical terms states that the performance of a personal computer doubles every 18 months . This trend has held steadfast for decades. However, a better correlation between electrical efficiency of computation and time has been developed by Koomey et al. [20]. It states that The electrical efficiency of computation has doubled roughly every year and a half for more than six decades, a pace of change comparable to that for computer performance and electrical efficiency in the microprocessor era.
14
The governing partial differential equations and boundary conditions are defined in terms of the continuous variables p, V etc. These can be approximated in the discrete domain in terms of the discrete variables pi, Vi etc. The discrete system is a large set of coupled, algebraic equations in the discrete variables. Solving and setting up this system requires a very large number of repetitive calculations which can easily be solved by a computer. The size of the grid or mesh determines the accuracy of the solution and the computational power required.
3.2 Software
This project exclusively involved the use of CFD software for all simulations. The software used was ANSYS, a commercial engineering simulation package. The ANSYS Workbench suite offers a wide range of engineering simulation solution sets that cover almost every aspect of engineering simulation required by a design process. 15
The geometry of the T-Junction was created in DesignModeler and an appropriate mesh was created using the Meshing application which was the next step of the workflow. Once these steps were completed, the fluid dynamics application in ANSYS could be launched to run simulations. After the simulations have converged, the results can be analysed using Fluent or analysed and presented using CFD-Post. Shown below is a typical ANSYS Workbench fluid flow analysis workflow.
Figure 3.2 ANSYS Workbench workflow Geometry DesignModeler Mesh Meshing Setup Fluent Results CFD-Post
Of the four main steps in the workflow, the setup and analysis using Fluent was the most important part. For this, a good understanding of turbulence modelling is required. Fluent offers many turbulence models, each with its strengths and weaknesses.
In CFD, turbulence appears to be dominant over all other flow phenomena when present. Properly modelling the turbulence in a given problem greatly increases the quality of simulations [22]. There are many turbulence models available today, each with its set of assumptions, advantages, disadvantages, mesh implications and computational requirements. Given the time constraints of this project, it was necessary to find a turbulence model that was both reasonably accurate and computationally inexpensive. A basic understanding of some of the commercially used turbulence models provided by Fluent was essential for the advancement of this project.
the Boussinesq hypothesis is that while it is true in simple flows like straight boundary layers such as boundary layers and wakes, it is not valid in more complex flows such as those involving accelerations and decelerations. Therefore, problems arise when twoequation models try to predict strongly rotating flows and other flows where curvature effects are significant. Some other flows where the - model may not be suitable are: Flows with boundary layer separation Flows with sudden changes in the mean strain rate Flows in rotation fluids
However, the - model has been shown to be useful for free-shear flows with relatively small pressure gradients. It is also less stable than models such as the SST - model. Furthermore, where the - model sacrifices a certain amount of accuracy, it makes up for it in lower computational requirements. The standard - model and the realizable - model are suitable for coarse meshes where the wall-cell y+ values are typically 30 and above. The realizable model usually gives better results than the standard model. The standard two-layer - model and the realizable two-layer - model offer the greatest flexibility in regards to the mesh. Compared to other - models, they produce the least inaccuracies for intermediate meshes (1 < y+ < 30) . The y+ value is the non-dimensional wall distance for a bounded flow and can be defined as follows:
y+
u* y
where u+ is the friction velocity at the nearest wall, y is the distance to the nearest wall and is the kinematic viscosity of the fluid . y+ is simply referred to as y plus and is commonly used in boundary layer theory. The two major shortcomings of the - model are that it over-predicts the shear stress in adverse pressure gradient flows because the length scale is too large and that it requires near-wall modification [27]. Despite this, when an uncertainty arises as to which turbulence model is to be used in a certain scenario, the realizable - model is a reasonable choice. 18
prevented the -equation from replacing the -equation as the standard scale-equation in turbulence modelling [29]. This makes the SST model very attractive for simulations in this project because of the need to model near wall as well as free stream flows. Once again the Boussinesq hypothesis is the main assumption in the SST - model because it is a two-equation model. It assumes that the Reynolds stress tensor, ij, is proportional to the trace-less mean strain rate tensor, S*ij.
dimensions and five additional equations to be solved in two dimensions. However, Large Eddy Simulation (LES) requires greater computational power than all of these. Obviously this greater computational power requirement is due to RSM including more physics than a two-equation turbulence model. Because of the computational complexity of the RSM, they have not been widely used for engineering applications. It would seem that the RSM would have the best chance of emerging as the ultimate turbulence model because it is not restricted by the Boussinesq hypothesis and because the closure contains the greatest number of model PDEs and constants of all the models considered.
operation when applied to the Navier-Stokes equations eliminates small scales of the solution. In large eddies, most energy and fluxes are explicitly calculated. In small eddies, little energy and fluxes are parameterized SFS (sub-filter scale) model. LES is supposed to be insensitive to the SFS model [37]. This reduces the computational cost of the simulation. The governing equations are thus transformed, and the solution is a filtered velocity field. LES resolves large scales of the flow field solution allowing better fidelity than alternative approaches such as RANS methods. It also models the smallest scales of the solution rather than resolving them as DNS does [38]. Because of this, it makes the computational cost for practical engineering systems with complex geometry or flow configurations attainable using supercomputers. In LES, the standard Smagorinsky model (SMG) is still widely used due to its algorithmic and numerical simplicity. However, the major drawback associated with this model is that the optimal model parameter is flow-dependent and ad hoc modifications of this parameter are required near solid surfaces [39]. The most compelling case for LES can be made for momentum, heat and mass transfer in free shear flows at high Reynolds numbers. There is good reason to expect LES to be successful, primarily because both the quantities of interest and the rate controlling process are determined by the resolved large scales. In a study by Y. Cheng et al. [39] in the context of turbulent flow over a matrix of cubes, a detailed comparison between the RANS (- model) and LES was carried out. Some of the conclusions that were drawn from the study were: The RANS results (more specifically, predictions provided by the standard - model) were found to be considerably different from the LES predictions and the experimental measurements. The size of the recirculation zone was overestimated in the RANS simulation. This creates a severe underestimation of the mean streamwise velocity component. The complex features (vortex shedding, large separation zones etc.) of the fully developed flow within and above an array of cubes are reproduced better with LES calculations, albeit at the disadvantage of much greater computation times. 22
In the present study, the computational cost associated with LES is about 100 times greater than that incurred with the - RANS model. The setup and use of turbulent flow simulations requires a profound knowledge of fluid mechanics, numerical techniques and the application under consideration. The susceptibility of LES to errors in modelling, in numerics, and in the treatment of boundary conditions, can be quite large due to nonlinear accumulation of different contributions over time, leading to an intricate and unpredictable situation[40]. One of the main difficulties arising in the evaluation of errors in LES is the non-linear accumulation of different error sources. The worst is the possible interaction between SGS modelling errors and numerical errors. In physical LES as described in [41], good numerical accuracy comes at a higher computational price. With the numerical methods usually employed, halving the grid spacing increases the computational cost by about a factor of 24 = 16. In conclusion, LES seeks to solve large spatial scales (like DNS) while modelling the smaller scales (-). Firstly, the larger scales carry the majority of the energy and therefore are more important methodology is a hybrid between these two methods which allows for the generation of useful solutions to transient flows, while still maintaining computationally realistic problems [42].
more accurate the result becomes. However, setting a steep convergence criterion also means that the simulation takes much longer to run. For these simulations, the convergence criteria were set at 1 x 10-3 as this was the default and anything higher would be an unnecessary, time-consuming investment for this project. The residual plots from six different simulations are shown below. The inlet velocities in all cases were 30m/s. Model Standard - Realizable - RNG - Standard - SST - RSM Iterations 99 104 262 235 296 1235
Table 3.1 Iterations required for different turbulence models with a convergence criterion of 1 x 10-3
(a) Standard -
(b) Realizable -
(c) RNG -
(d) Standard -
24
(e) SST -
(f) RSM
Figure 3.3 Residual plots of various turbulence models with a convergence criterion of 1 x 10-3
The obtained results were as theory indicated. The standard - required the least number of iterations for the solution to converge. The Reynolds stress model simulation was at the other end of the scale with 1235 iterations. This is because there are five additional transport equations that must be solved in a 2D flow. Given the time constraints of this project, this was an unrealistic model to use. Furthermore, the velocity contours of the -, - and RSM models were compared to finalise the choice for the most suitable turbulence model. The choice was immediately clear. The - model, while fast in obtaining results, produces results that are quite inaccurate. This can be seen in Figure 3.4 (a) where the velocity at the central axis of each branch pipe is in the region of ~40 m/s to ~48 m/s. This is simply not true because the inlet velocity is specified at 30m/s and this value cannot be higher unless influenced by another flow or geometry. The RSM produces results that are quite accurate in terms of the velocity contours. The velocity profile on the main pipe is what would normally be expected and the velocity in the branch pipes are around 30m/s. However, as mentioned previously, the weakness of RSM is that it is very computationally expensive. The SST - model was found to be an excellent compromise between the two. The velocity profile, while not as accurate as the RSM, it comes very close as can be seen in Figure 3.4 (b) & (c).
25
(a) Standard -
(b) SST -
(c) RSM Figure 3.4 Velocity contours of three different turbulence models
In conclusion, the SST - model was chosen because it incorporates the free stream behaviour of the - model and the near wall behaviour of the - model. The velocity profile obtained from the SST - model very closely matched the velocity profile from the RSM simulation. Additionally, it was able to solve the problem in an acceptable timeframe and computational requirement (296 iterations) whereas RSM required nearly four times as many iterations.
26
Method
The procedure for setting up and running each simulation was the same.
Different simulations sometimes shared the same geometry and meshing and therefore a standard geometry and mesh could be created and transferred over to each simulation. The workflow involved the following steps.
4.1 Geometry
The geometry was first created in DesignModeler, the geometry creation application in ANSYS Workbench. DesignModeler is a parametric modelling application. Parametric modelling allows for the use of parameters to define a geometry or model. As a result, the geometry can be altered with ease as opposed to direct modelling. Direct modelling is analogous to using constants in defining dimensions whereas in parametric modelling, variables are used. While direct modelling is a perfectly viable modelling approach, for complex parts or assemblies or parts that have multiple dimensions and variations, parametric modelling is a better choice. The geometry of the T-Junction was identical to the geometries described in the cylindrical pipe and rectangular duct cases by Ziada et al. in [1]. The cylindrical duct 2D cross-sectional geometry was only used for a few initial simulations as the behaviour of the flow would be drastically different in a 3D scenario because the flow is cylindrical (Figure 4.2). Therefore a 2D simulation would not be an accurate representation. On the other hand, the cross-section of the rectangular duct could be considered the same in the z-direction and so a 2D representation of the flow would be reasonably accurate at the central axis of the pipe. The most important dimension of the pipe setup was the length of the branch pipe as this was determined by the wavelength of the primary branch acoustic node as shown in Figure 4.1.
Figure 4.1 Primary branch acoustic mode [1]
27
Figure 4.2 (left) 3D flow in a pipe of cylindrical cross section [43] (right) 2D flow in a pipe of cylindrical cross section at the central axis but is the same for a rectangular duct [44]
Figure 4.4 shows one of the first geometries created for this project. This geometry was created using the geometry described for the cylindrical pipe case in [1] as shown in Figure 4.3. The half-length of this specific transition zone was determined using the relationship:
L = 1 D
where L is the half-length of the transition zone and D is the diameter of the transition zone and the main pipe. The length of the branch pipe, LB was 1.42 m. These figures are obtained from a table from [1] that details the dimensions of eight cylindrical pipe cases (Figure 4.3(right)). The 45 chamfer shown in the dotted circle in Figure 4.3(left) was ignored so that the flow separation and vortex formation could be better visualised. The diameter of the branch pipe, d was 0.076 m and D was 0.102m. The length of the transition zone 2L was calculated to be 0.204 m. The length of the main pipe was 1.5LB. This is derived from the fact that the wavelength of the primary acoustic node , was equal to 2LB and the length of the main pipe LM was equal to 3/4.
Figure 4.3 (left) Dimensions of T-Junction with cylindrical geometry [1] (right) Table displaying the dimensions and relationships between L and D [1]
28
4.2 Meshing
Perhaps the part of the workflow that influences the accuracy of the solution most is the mesh. The mesh represents the continuous domain as a discrete domain. In order to analyse fluid flows, the flow domain is split into smaller subdomains. The governing equations are then discretized and solved inside each of these subdomains. The subdomains are generally called cells or elements and a collection of these is called a mesh or grid. The subdomains are made of basic geometry such as hexahedra and tetrahedra in 3D and quadrilaterals and triangles in 2D. The mesh density has a direct correlation to the accuracy of the solution. The greater the mesh density, the more accurate the solution becomes. However, greater mesh densities result in more computationally expensive simulations. Therefore, the ideal mesh must be dense enough to obtain a reasonably accurate solution but not 29
excessively dense that a simulation requires an unreasonable amount of time. Meshes can be optimised so that the density is greater in areas of interest or areas of important flow structures. This allows for efficient use of computational resources. Mesh creation in ANSYS is achieved using the Meshing application. This is the second step of the workflow. Initially, the geometry shown in Figure 4.4 was meshed using a quadrilateral based mapped face meshing method. Mapped face meshing creates a very uniform mesh of either quadrilaterals or triangles as specified. In order to achieve greater mesh complexity, the edge sizing tool was used in conjunction with mapped face meshing. This gave greater control over the mesh as it allowed for the manual division of cells at each region or wall. The other meshing scheme that was used involved the use of inflation layers. This is a much better meshing approach as inflation layers are useful for greater resolution at the boundary layers of the flow. This means that the mesh density is much greater at the boundary layer and every layer after the first layer grows in height by a growth rate that can be specified. The first layer height y is calculated as follows:
y = L y 80 Re
13 14
, where Re =
V d
This equation for y is from the ANSYS 11 documentation [45]. y+ is the desired y+ value which is 1 for - turbulence models . is the density of the fluid, V is the velocity, d is the diameter of the pipe and is the viscosity. Using this, the first layer height was calculated to be 2x10-4 m. However, the first layer height was set at 1x10-4m as this was to capture the boundary layer with a good level of accuracy. For this case, a growth rate of 1.1 was used, i.e. each layer was 10% taller than the layer before it. The mesh density was lower in other parts of the flow such as the central region of the TJunction and around the central axis of the branch and main pipes. In this region, triangles were used rather than the quadrilateral scheme in the inflation layers. The results for both methods were expected to be different in that the method using inflation layers should result in a much more accurate solution. This is detailed in the results section. Figure 4.5 shows the two different meshing approaches. 30
(c) Inflation layers at the edge of the geometry magnified. Figure 4.5 Two different meshing approaches
31
4. Next, the cell zone conditions were set. This step assigned the material selected in step 2 to the geometry. Since air was the default material, this was changed to methane. 5. The boundary conditions for the problem can now be set. The main user inputs here are the inlet velocity and the turbulence specification. For all the simulations in the project, the velocity was input as components and the turbulence was specified by the turbulent intensity and the hydraulic diameter. Only the x-velocity is entered as the flow is considered horizontal at the inlets. The turbulence intensity was set at the default value of 10%. The values of hydraulic diameter were calculated depending on the cross sectional profile of the pipe or duct. The hydraulic diameter was calculated using the following equations from :
dh =
width of the duct. All dimensions in m. Cylindrical Pipe dh, branch 0.076 dh, main 0.102 Rectangular Duct dh, branch 0.07 dh, main 0.090254
Table 4.1 Hydraulic diameters calculated for the cylindrical pipe and the rectangular duct
6. The pressure-velocity coupling scheme was set to SIMPLE (Semi-implicit method for pressure-linked equations) and the spatial discretization method for the momentum, turbulent kinetic energy, and the specific dissipation rate were set to Second Order Upwind. Upwind schemes are a class of numerical discretisation methods for solving hyperbolic partial differential equations. The origin of upwind methods can be credited to the work of Courant, Isaacson and Rees [48]. The order of discretization refers to the convective terms of the equations. Second order discretization generally yields better accuracy while the convergence is more robust in first order discretization. 33
7. In the monitors tab, the convergence criteria for the residuals of the solution can be set for the values of continuity, x-velocity, y-velocity, and . As mentioned before, residuals are a measure of how well a solution satisfies the discrete form of each governing equation. Some tutorials suggest a steep convergence criterion such as 1x10-6 . Initially for the simulations, the convergence criteria were set at 1x10-6. However, it was soon discovered that such a high degree of accuracy was not absolutely required and was an unnecessary time investment. This is demonstrated in the results section. The monitors tab also allows the user to create surface and volume monitors. This enables the creation of very useful custom plots that retrieve data from a desired location in the flow. 8. The solution must now be initialized. Since the method of solving a problem in Fluent is an iterative process, it requires an initial set of values to begin the calculation. These values can be obtained from one or all of the parts of the flow as specified in the drop down menu. The initial values were computed all zones for all simulations. 9. For a transient simulation, Fluent gives the user the option of recording animations of the solution once the solution has been initialized. This is an extremely useful tool in the analysis of the results. 10. Finally, the calculation can be run. The number of iterations of the solution to be calculated for and a few other plotting options can be specified here.
34
Results
The difference in mesh density and composition can Geometry # L LB D d Chamfer VB 1 0.102 m 0.482 m 0.102 m 0.076 m No 30 m/s
35
Although there were more nodes in the case of the better mesh (64,338 elements vs. 18,223 elements), the bad mesh required a greater amount of iterations (254 vs. 205 for the better mesh) for the solution to converge. However, the time required per iteration was greater in the case of the better mesh. This leads to the conclusion that the number of iterations required are not an indication of how complex the mesh is, but rather a characteristic of the quality of the mesh. An extremely dense mesh is extremely wasteful and although the calculation may finish in fewer iterations, the time required per iteration would be much higher. Therefore, it is necessary to generate a mesh which has enough complexity where required (such as near-wall and boundary layers) but also reduced density in areas where the flow does not have to be modelled at such a fine level. 36
A velocity contour map reveals drastic differences between the two meshes. It is evident that near-wall and boundary layer fluid behaviour is badly modelled in the case of the bad mesh. The contours are much more realistic in the contour map on the right. Notice the areas of separated areas high velocities (indicated by the orange to red areas) on the contour map on the large mesh. It makes more sense that the areas would be connected and the resulting velocity would be greater at the entrance to the main pipe as a result of continuity. The continuity equation states that the flow rate into a system is equal to the flow rate out of a system so the reduction in area would mean an increase in velocity from the following equations.
Q = Ai i and Qin = Qout
where Q is the volume flow rate, A is the area of the cross section of the flow and V is the velocity of the fluid. Figure 5.3 clearly shows that the mesh used on the left is a very poor choice when it comes to modelling near-wall behaviour. Therefore, it is logical to say that better results can be achieved with a denser mesh near the walls of the T-Junction. From my experience, I believe that the time invested in generating a well-tailored mesh is rewarding when it comes to the solution generated. In this case, the mesh used on the right required a lot more time to create than the one on the left.
Figure 5.3 Difference in velocity contours between the bad mesh (left) and the better mesh (right)
37
Figure 5.4 Results of a simulation between convergence criteria of 1 x 10-3 (left) 1 x 10-6 (right)
According to Figure 5.4 above, it is clear that the flows upstream and at the TJunction are almost identical in both cases. The difference is that the simulation with convergence criteria of 1 x 10-6, the flow downstream of the T-Junction is more accurately modelled, but at an unjustifiable computational cost as the region beyond the T-Junction is not being analysed in this project. Although there is a marginal increase in accuracy in the flow coming into the junction, it is offset by the computational cost. Therefore, it was decided that convergence criteria of 1 x 10-3 would be used throughout 38
the project. The solution had converged after 205 iterations for the 1 x 10-3 case whereas the 1 x 10-6 required 1621 iterations. Figure 5.5 shows this and a few conclusions can be drawn from this plot. Firstly, I believe that if time is not an issue, opting for a lower convergence criteria is a good choice. Therefore, for a particular geometry, with the same mesh, a pilot simulation with unreasonably low convergence criteria should be run. From the residual plot of this, the point at which all the residuals reduce with a steady slope (after ~920 iterations in this case) is a good indicator as to what convergence criteria must be used. Following simulations can be run with the convergence criteria corresponding to ~920 iterations. According to the plot below, 5x10-5 is a good convergence criteria provided time is not an issue. The difference between 5x10-5 and 1 x 10-6 is small compared to the difference in iterations between the two points. From other simulations conducted, the plot continues with the same slope indefinitely.
It is important to note that for these simulations, although LB = 1.42 m, it didnt necessarily have to be so. Ignoring the effects of acoustics, LB only needed to be long enough so that the fluid at the inlet would not have a significant influence on the fluid flow in the T-Junction as would be the case if LB was too short. 39
Junction without chamfered inlets is the reduction of vorticity. The simplest definition of vorticity is the tendency of an element in a fluid to turn. It is also known as the curl of the velocity vector. In the context of fluid dynamics, vorticity can be related to the amount of circulation in a fluid flow [50].
Figure 5.6 Vorticity contours of a T-Junction with chamfer (left) and without (right)
The contours were set at a range from 0-1000 s-1. Therefore, it is clear from Figure 5.6 that the maximum vorticity is a greater value in the T-Junction on the right. It is important to minimise the amount of vorticity because it excites acoustic resonance. However, for the purposes of simulations, T-Junctions without chamfered inlets will be used because it is easier to generate oscillation. This is also one of the reasons why a majority of the experimentation in [1] was carried out in non-chamfered T-Junctions. 40
geometries of the same basic template and dimensions were used (Figure 5.8).
Figure 5.8 Four cases of rectangular geometry T-Junctions based on the template on the left [1]
Geometry # L (m) LB (m) D (m) d (m) Chamfer VB (m/s) dh, branch (m) dh, main (m)
41
The geometry in this series of simulations followed those described in [1]. The T-Junction had a length (2L) that was 3.5 times the width (see Figure 5.8). The length of each branch pipe was 1.22 m. VB was calculated using the following equation from [1]:
VR = VB VB = 43.27 m / s f
Where VR is the reduced velocity (1.65), f is the frequency of the lowest acoustic mode of the branches (118 Hz) and is the characteristic length which was equal to the halflength of the transition zone (0.22225 m). In this configuration, VB was about 9% [1] lower than VM. VM can be calculated using the continuity equation as was found to be 9.3% lower than the calculated VB.
2 Q B = QM
Figure 5.9 Velocity swirling vector contour map of the flow in a T-Junction
42
Figure 5.10 Vorticity contours of the flow development in the branch pipe (flow from right to left)
(a) Case 1
(b) Case 2
(c) Case 3
(d) Case 4
Figure 5.11 Vorticity contours of the four cases. Vortex formation is strongest in the red regions
The geometry that is most prone to vortex shedding and interaction is Case 1. The transition zone means that strong vortices are allowed to develop in the upper half of the T-Junction especially around the central axis as shown in Figure 5.11 (Case 1). 43
Although Case 2 and Case 3 are identical in terms of cross section, the placement of the transition zone has a major influence on the flow. Vortex formation is extremely mild in Case 2 because there is no significant vortex formation taking place in the upper portion of the T-Junction. The vortex being formed in the lower portion, though not ideal, is acceptable because it is contained in the corner and not allowed to interact with other vortices by the flow. However, in Case 4 we see the least amount of vortex formation. Therefore, perhaps it would not be completely wrong to assume that a T-Junction without a transition zone is the best type of T-Junction. This is best reinforced by the fact that these results correspond with the data obtained in [1] as shown below.
Figure 5.12 Normalised acoustic pressure as a function of reduced velocity for the four test cases [1]
parameters for these simulations are exactly the same as shown in Table 5-3. A time step of 0.000847 s is calculated from the frequency of the lowest acoustic mode (f = 118 Hz) mentioned in section 5.4.
1 f 10
where is the time step. f is multiplied by 10 so that a tenth of each period can be visualised, otherwise only the beginning of every period can be captured. The results obtained from these simulations were disappointing for the fact that the flow was completely symmetric. Periodic vortex shedding was expected but the velocity in each simulation, after reaching a steady state, simply flat lined. Vorticity contours in this case, after reaching a steady state would resemble images such as those shown in Figure 5.11.
(a) Case 1
(b) Case 2
(c) Case 3 (d) Case 4 Figure 5.13 Velocity plots of the four cases at various locations of the T-Junction
Many other simulations were performed, some with slightly different inlet velocities. In all cases, there was no periodic vortex shedding at the T-Junction. One of the reasons for this was that since the flow was contained in a small pipe, any oscillation in the flow would be contained by the walls. Also, since the flow is being sucked down the duct, the effect of vortices would be negated. This is unlike external flows across a 45
cylinder or a flat plate where periodic vortex shedding is easily induced and can be simulated with ease. The slightest difference in flow symmetry creates a snowballing effect and this brings about periodic vortex shedding. The other reason that an oscillation could not be induced was that unlike the real world where there can be imperfections and asymmetries, Fluent models both branch pipes as completely identical and perfect. This means that the flow is exactly the same on both sides if the parameters at both inlets are the same.
VB = VInlet + a Sin( A t )
where A was the frequency in rad/s (A = 118 x 2 = 741.42 rad/s), a was the amplification factor and t was the current time of the simulation. This increases in increments of time step. The amplification factor simply increases the amplitude of the oscillation in flow velocity. The effect of this UDF on the inlet velocity at the branch pipe is shown in Figure 5.14. The velocity oscillated around 43.27 m/s at both inlets with an amplitude of 2.86 m/s (this is controlled by a). Figure 5.15 shows the results
46
obtained by Ziada et al. [1]. The effect of using a UDF is immediately evident (Figure 5.16). The sampling point in Case 3 was placed in a region of almost no oscillation.
0.025
0.02
0.01
Velocity at branch pipe inlets relative to the central axis of the T-Junction (m/s) Figure 5.14 Oscillation of branch velocity with time
Figure 5.15 Instantaneous flow structure images and sketches for a complete cycle of Mode A oscillation (VR = 1.65 and f = 118 Hz) [1]
47
(a) Case 1
(b) Case 2
(c) Case 3
(d) Case 4
Figure 5.16 Velocity plots of the four cases at various locations of the T-Junction (with UDF)
Comparing Figure 5.18 to Figure 5.15 it was evident that the simulation was quite successful at modelling the periodic vortex
shedding observed in [1]. The regions bordered by red contours in the vorticity contour maps in Figure 5.18 represent areas with the
strongest vortex shedding. The dynamic pressure contours also fluctuate at the specified frequency. The lower, upper and central
Figure 5.17 Combined vector and streamline map of regions of recirculation (blue regions)
regions of the T-Junction and the walls at the entrance of the main pipe show regions of recirculation (Figure 5.17).
48
(a) 0
(b) 90
(c) 180
(d) 270
Figure 5.18 Vorticity (500 1000 s-1) (left) and dynamic pressure (500 1000 Pa) (right) contour maps at different phase angles for Case 1
49
Conclusion
This project initially set out with the goal of computationally simulating the fluid
flow in a T-Junction as investigated by Ziada et al. [1]. During the course of the project however, it became a question as to whether CFD is actually viable for a flow configuration such as this given the complexity of the physics involved. The most practical model for numerical simulation of flow in T-Junctions was found to be the SST - model as it produced results that were almost as good as the RSM while only requiring a reasonable amount of computational power. It was also better suited for this problem as it took on the traits of the - models reduced sensitivity at the free stream and the - models accuracy at near wall and boundary layers. The effects of meshing on the solution are also presented which shows the importance of inflation layers for simulating the flow in a very efficient manner. This study has shown that while it is possible to replicate the flow in a TJunction using CFD, the solution greatly depends on the amount of information that can be conveyed to the software. Simulating external flows are easier in comparison as the onset of vortex shedding is brought about by the slightest instability. The flow in a T-Junction is inherently stable but at certain flow rates, acoustic resonance is generated and this could not be modelled by Fluent using a simple simulation. Therefore, a UDF was used to generate an oscillation in the flow which would initiate periodic vortex shedding. Using a UDF proved to be a viable method of imitating the flow. The effect of flow-acoustic coupling was artificially simulated using a sin wave function which created a periodic oscillation in the inlet velocities. The results of the simulations were surprisingly close to the results from experiments [1]. Despite this, the fact remains that this modelling was only possible because the flow characteristics were known. This is not ideal when creating optimal T-Junction geometry as the user may not be aware of the flow-acoustic coupling phenomenon. Therefore, the results of CFD alone cannot be 50
considered the definitive authority in this problem, at least from this study. However, if the effects of flow-acoustic coupling are understood, then Fluent becomes a much more potent tool especially when used in conjunction with actual experimentation. Furthermore, as computational technologies advance the computational effort required for simulations decrease. Koomeys Law [20] describes how the computational efficiency doubles roughly every 1.5 years. Considering these, CFD has a very promising future. Further study in this area should focus on modelling the acoustic aspect of the flow. The end result i.e. the unsteady flow in this study was modelled by artificially stimulating vortex shedding as RANS produces inherently stable results. Then perhaps, an LES is a better modelling approach. LES offers a much better representation of turbulent flow structures (Figure 6.1, Figure 6.2). The reason for using a RANS model is its relatively low computational cost. However, when this is not an issue, LES is a superior option. Obviously, if one desires greater accuracy still, DNS can be used but the computational power required is simply unrealistic.
51
List of References
1. Ziada, S., McLaren, K.W., and Li, Y., Flow-Acoustic Coupling in T-Junctions: Effect of T-Junction Geometry. Journal of Pressure Vessel Technology, 2009. 131(4): p. 041302. 2. Howe, M.S., On the Absorption of Sound by Turbulence and Other Hydrodynamic Flows. Journal of Applied Mathematics, 1984. 32: p. 181-209. 3. Ziada, S., Scott, A., and Arthurs, D., Acoustic Excitation by Flow in T-Junctions. Journal of Pressure Vessel Technology, 2007. 129: p. 14-20. 4. Chen, Y.N. and Florjancic, D., Vortex-Induced Resonance in a Pipe System Due to Branching. Proceedings of the IMechE conference on Vibration and Noise in Pump, fan and Compressor Installations, 1975: p. 79-86. 5. Additional Flow-Induced Vibration Failures After A Recent Power Uprate. U.S. Nuclear Regulatory Commission NRC Information Notice 2002-26, 2002. 6. Michalke, A., On Spatially Growing Disturbances in an Inviscid Shear Layer. Journal of Fluid Mechanics, 1965. 23(3): p. 521-544. 7. Okuyama, K., et al., Flow-induced acoustic resonance at the mouth of one or two side branches. Nuclear Engineering and Design, 2011. 8. Karlsson, M., Aeroacoustic studies of duct branches - with applications to silencers. Doctoral Thesis, 2011. 9. Bruggeman, J.C., et al., Self-sustained aero-acoustic pulsations in gas transport systems: Experimental study of the influence of closed side branches. Journal of Sound and Vibration, 1991. 150(3): p. 371-393. 10. 11. Bruggeman, J.C., Flow-Induced Pulsations in Pipe Systems. Ph.D. Thesis, 1987. Ziada, S., A FlowVisualizationStudy of Flow- Acoustic Coupling at the Mouth of a Resonant Side-Branch. Journal of Fluids and Structures, 1994. 8(4): p. 391-416. 12. Karlsson, M. and Abom, M., Aeroacoustics of T-Junctions - An Experimental Investigation. Journal of Sound and Vibration, 2010. 329(10): p. 1793-1808. 52
13.
Karlsson, M. and Abom, M., Quasi-steady model of the acoustic scattering properties of a T-Junction. Journal of Sound and Vibration, 2011. 330(21): p. 5131-5137.
14.
Lacombe, R., et al., Experimental and Numerical Investigations on the Whistling Ability of an Orifice in a Flow Duct The 17th International Congress on Sound & Vibration, 2010.
15.
[Accessed:
20 March 2012];
http://www.cerfacs.fr/4-26334-The-AVBP-code.php. 16. Garcia, J.P., et al., Numerical and experimental investigations on internal compressible flow at T-type junctions. Experimental Thermal and Fluid Science, 2006. 31(1): p. 61-74. 17. Tonon, D., Willems, J.F.H., and Hirschberg, A., Self-sustained oscillations in pipe systems with multiple deep side branches: Preduction and reduction by detuning. Journal of Sound and Vibration, 2011. 330(24): p. 5894-5912. 18. Tonon, D., et al., Whistling of a pipe system with multiple side branches: Comparison with corrugated pipes. Journal of Sound and Vibration, 2010. 329(8): p. 1007-1024. 19. The Economist A deeper law than Moore's? http://www.economist.com/node/21531350. 20. Koomey, J.G., et al., Implications of Historical Trends in the Electrical Efficiency of Computing Annals of the History of Computing, 2011. 33(3): p. 46-54. 21. 22. 23. Bhaskaran, R. and Collins, L. Introduction to CFD Basics. Sodja, J., Turbulence Models in CFD. University of Ljubljana, 2007. CFD Online. Two equation turbulence models. [Accessed: 1 March 2012]; www.cfd-online.com/Wiki/Two_equation_turbulence_models. 24. Rahman, M.M., Karim, M.M., and Alim, M.A., Numerical investigation of unsteady flow past a circular cylinder using 2-D finite volume method. Journal of Naval Architecture and Marine Engineering 2007. 4(1): p. 30. 53 [Accessed: 20 March 2012];
25.
kxcad. How Do I Choose a K-Epsilon Model and Wall Treatment? . [Accessed: 2 March 2012]; http://www.kxcad.net/STAR-CCM/online/139-
kEpsilonTurbulence-15.html. 26. CFD Online. Dimensionless wall distance (y plus). [Accessed: 5 March 2012]; http://www.cfd-online.com/Wiki/Dimensionless_wall_distance_%28y_plus%29. 27. 28. Davidson, L., The SST Model. MTF270 Turbulence Modelling, 2006: p. 93. Menter, F.R., Two-equation eddy-viscosity turbulence models for engineering applications. AIAA Journal, 1994. 32(8): p. 1598-1605. 29. Menter, F.R., Kuntz, M., and Langtry, R., Ten Years of Industrial Experience with the SST Turbulence Model. Proceedings of the 4th International Symposium on Turbulence, Heat and Mass Transfer, 2003: p. 625-632. 30. 31. ANSYS, Turbulence Modelling. ANSYS Brochure, 2011. Karim, M.M., Rahman, M.M., and Alim, M.A., Performance of SST k- Turbulence Model for Computation of Viscous Drag of Axisymmetric Underwater Bodies. International Journal of Engineering, 2011. 24(2): p. 139-146. 32. Lauder, B.E., Reece, G.J., and Rodi, W., Progress in the development of a Reynolds-stress turbulence closure. Journal of Fluid Mechanics, 1975. 68(3): p. 537-566 33. Rao, P.S., Modeling of Turbulent Flows and Boundary Layer. Computational Fluid Dynamics, 2010: p. 285-306. 34. Fluent Inc. The Reynolds Stress Model (RSM). 2003 [Accessed: 12 February 2012]; http://jullio.pe.kr/fluent6.1/help/html/ug/node413.htm. 35. Smagorinsky, J., General Circulation Experiments with the Primitive Equations. Monthly Weather Review, 1963. 91(3): p. 99164. 36. Fureby, C. and Grinstein, F.F., Large Eddy Simulation of High-Reynolds-Number Free and Wall-Bounded Flows. Journal of Computational Physics, 2002. 181(1): p. 68-97. 37. 54 Moeng, C.-H., Large Eddy Simulation. 2003.
38. 39.
Pope, S.B., Turbulent Flows. 2000. Cheng, Y., et al., A comparison of large Eddy simulations with a standard - Reynolds-averaged Navier-Stokes model for the prediction of a fully developed turbulent flow over a matrix of cubes. Journal of Wind Engineering and Industrial Aerodynamics, 2003. 91(11): p. 1301-1328.
40.
Meyers, J., Gaurts, B., and Saguat, P., Quality and Reliability of Large-Eddy Simulations. 2008: p. 380.
41.
Pope, S.B., Ten questions concerning the large-eddy simulation of turbulent flows. New Journal of Physics, 2004. 6(35).
42. 43.
Richardson, P.S., Improving the thermal processing of foods. 2004: p. 99. Accuracy Aesthetics. Streamlining. 2007 http://accuracyandaesthetics.com/?p=401. [Accessed: 5 March 2012];
44.
Drilling-Mud.org. Annular Velocity affects Hole Cleaning. 2011 [Accessed: 5 March 2012]; http://www.drilling-mud.org/annular-velocity-affects-hole-
cleaning/. 45. ANSYS First Layer thickness. 2011 [Accessed: 8 March 2012];
http://www.kxcad.net/ansys/ANSYS/workbench/cm_firstprismheight.html. 46. CFD Online. Near-wall treatment for k-omega models. [Accessed: 8 March 2012]; omega_models. 47. The Engineering Toolbox. Hydraulic Diameter. [Accessed: 8 March 2012]; http://www.engineeringtoolbox.com/hydraulic-equivalent-diameterd_458.html. 48. Courant, R., Isaacson, E., and Rees, M., On the Solution of Nonlinear Hyperbolic Differential Equations by Finite Differences. Communications of Pure and Applied Mathematics, 1952. 5(3): p. 243-255. http://www.cfd-online.com/Wiki/Near-wall_treatment_for_k-
55
49.
[Accessed:
10 March 2012];
https://confluence.cornell.edu/display/SIMULATION/FLUENT++Turbulent+Pipe+Flow+-+Step+5+*New. 50. 51. Clancy, L.J., Aerodynamics. 2006. 1st ed. Fluent Inc. . Fluent 6.3 UDF Manual. 2006 http://www.hipecc.wichita.edu/pdfs/fludf.pdf. 52. ANSYS. Boundary Conditions. 2009 [Accessed: 15 March 2012]; [Accessed: 15 March 2012];
www.sharcnet.ca/Software/Fluent12/html/udf/node243.htm.
56
Appendix
T-Junction Geometries
All dimensions in m.
57
58
59
begin_f_loop (f, thread) { F_PROFILE (f, thread, position) = 43.27 + 3*sin(741.42*t); } end_f_loop (f, thread) }
begin_f_loop (f, thread) { F_PROFILE (f, thread, position) = -43.27 + 3*sin(741.42*t); } end_f_loop (f, thread) }
60