Documente Academic
Documente Profesional
Documente Cultură
SERVICE MANUAL
COLOR TELEVISION RECEIVER
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
IMPORTANT
Inferior silicon grease can damage IC's and transistors. When replacing an IC's or transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon.
A1-1
CONTENTS
SERVICING NOTICES ON CHECKING .......................................................................................................... A1-1 HOW TO ORDER PARTS ............................................................................................................................... A1-1 IMPORTANT .................................................................................................................................................... A1-1 CONTENTS ..................................................................................................................................................... A2-1 GENERAL SPECIFICATIONS ........................................................................................................................ A3-1~A3-4 DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ................................................................................................................. B1-1 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................................... B2-1, B2-2 SERVICE MODE LIST ..................................................................................................................................... C-1 CONFIRMATION OF HOURS USED .............................................................................................................. C-1 WHEN REPLACING EEPROM (MEMORY) IC ............................................................................................... C-1 ELECTRICAL ADJUSTMENTS ....................................................................................................................... D-1~D-5 BLOCK DIAGRAM ........................................................................................................................................... E-1, E-2 PRINTED CIRCUIT BOARDS MAIN/CRT .................................................................................................................................................... F-1~F-4 SCHEMATIC DIAGRAMS MICON/CHROMA/TUNER ........................................................................................................................... G-1, G-2 DEFLECTION/CRT ...................................................................................................................................... G-3, G-4 POWER ....................................................................................................................................................... G-5, G-6 SOUND ....................................................................................................................................................... G-7, G-8 COMB/FILTER ............................................................................................................................................. G-9, G-10 AV..................................................................................................................................................................G-11, G-12 WAVEFORMS .................................................................................................................................................. H-1, H-2 MECHANICAL EXPLODED VIEW ................................................................................................................... I-1 MECHANICAL REPLACEMENT PARTS LIST ............................................................................................... J1-1 ELECTRICAL REPLACEMENT PARTS LIST ................................................................................................. J2-1, J2-2
A2-1
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Deflection Magnetic Field BV/BH 27 inch / 676.0mmV Normal 108 degree +0.45G/0.18G NTSC 2Speaker Front 2.0 x 3.5 Inch 8 ohm 2.5 + 2.5 W 2.0 + 2.0 W No US System M 1Tuner Other F-Synth VHF/UHF 75 ohm 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No Yes Yes 120V AC 60Hz at AC Stand by (at AC) Per Year Power Fuse Safety Radiation X-Radiation Operation Storage 125 W at AC 120 V 60 Hz 5 W at AC 120 V 60 Hz -kWh/Year Yes UL FCC DHHS +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH Yes Character Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes No No No Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes No Yes Yes No
G-2
T u n in g System
System Destination Tuning System Input Impedance CH Coverage Picture(FP) Sound(FS) FP-FS
Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting Power Source Power Consumption
G-3
Power
AC DC
Menu Type Picture Contrast Brightness Color Tint Sharpness Audio Bass Treble Balance BBE On/Off Stable Sound On/Off Surround On/Off CH Set Up TV/CATV Auto CH Memory Add/Delete Language V-chip CH Label Favorite CH Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream
A3-1
GENERAL SPECIFICATIONS
Channel(TV/Cable) CH Label Sleep Timer Sound Mute V-chip Rating G-8 G-9 OSD Language Clock and Timer Sleep Timer Max Time Step Program(On Timer / Off Timer) Yes No Yes Yes Yes English
French
Spanish
G-10
Remote Control
G-11
Features
On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode) more than Unit Glow in Dark Remocon Format Custom Code Power Source Voltage(D.C) UM size x pcs Total Keys Keys Power 1 2 3 4 5 6 7 8 9 0 100 CH Up CH Down Volume Up Volume Down TV/Caption/Text CH1/CH2 TV/Video(TV/AV) CH RTN/CH ENT(Quick View) Sleep RE Call(Call) Reset Menu Enter Mute Exit MTS(Audio Select) Set + Set Multi Brand Keys CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) CH Enter Code Set (Code) FF Rew Rec Play Stop TV VCR Cable Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type BBE Auto Search CH Allocation SAP
120 Min 10 Min No No -Min RC-GT No NEC 86-05 h 3V UM-4 x 2 pcs 28 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes No No No No No No No No No No No No No No Yes Yes No Yes No No Yes Yes Yes USA, ORION Type No No No Yes
Sec
A3-2
GENERAL SPECIFICATIONS
Tone Control Channel Lock Just Clock Function Game Position CH Label VM Circuit Full OSD Premiere Comb Filter Auto CH Memory Hotel Lock Closed Caption Stable Sound Surround Energy Star Power On Memory Favorite CH Owner's Manual Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safeguard Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card Information Sheet PTB Sheet 300 ohm to 75 ohm Antenna Adapter Switch Front Power System Select Main Power SW Sub Power Channel Up/Reset Channel Down/Enter Volume Up/Set Up Volume Down/Set Down Menu: Vol Up + Vol Down Rear AC/DC TV/CATV Selector Degauss Main Power SW Indicator Power Stand-by On Timer Terminals Front Video Input Audio Input Other Terminal Rear Video Input(Rear1) Video Input(Rear2) Audio Input(Rear1) Audio Input(Rear2) Video Output Audio Output S-Input Color Stream Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input No No No No No No No No No No No No No No No No No No No Yes No No No Yes Yes Yes Yes Yes No No No No No No No RCA RCA x 2 No RCA No RCA x 2 No RCA RCA x 2 Yes No No No No F Type No Yes No No No No No No No No Lines Yes No Yes Yes Yes No No No English / Spanish Yes Yes No
G-12
Accessories
G-13
Interface
A3-3
GENERAL SPECIFICATIONS
G-14 G-15 G-16 Set Size Weight Carton Master Carton Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Dimensions W x D x H(mm) Design Description of Origin Drop Test Height (cm) Container Stuffing Cabinet Cabinet Front Cabinet Rear PCB Non-Halogen Demand Eyelet Demand AC Outlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) No 650 x 500.5 x 571.5 36.5kg ( 80.5 lbs) 40.5Kg (89.3 lbs) No ---Sets -/--- x -- x -No Yes Double/WHITE CORRUGATED CARTON 731 x 580 x 665 As per Buyer's Yes Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces 31 192 Sets/40' container PS 94V0 DECABROM PS 94V0 DECABROM No No
G-17
Material
A3-4
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.)
* *
After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged.
REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 1-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated screwdriver, touch the support of the Anode with the tip of the screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap
Fig. 1-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Screwdriver
Fig. 1-1
Fig. 1-4 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5.
2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 1-2.) Rubber Cap
CRT
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts.
B1-1
DISASSEMBLY INSTRUCTIONS
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC
REMOVAL 1. Put the Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 2-1.) NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Blower type IC desoldering machine
3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) NOTE Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
IC
Tweezers
Fig. 2-1
IC
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 2-2.) NOTE Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely.
Fig. 2-3 4. Peel off the Masking Tape. 5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Soldering Iron
IC pattern IC
Fig. 2-4
Fig. 2-2
B2-1
DISASSEMBLY INSTRUCTIONS
INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 2-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 2-8.)
IC
Soldering Iron
Fig. 2-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case.
Solder temporarily
Solder temporarily
Fig. 2-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.)
Solder
Soldering Iron
IC
Fig. 2-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
Fig. 2-7
B2-2
INIT
00
50
CRT ON 0010
FIG. 1
C-1
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL ADJUSTMENTS
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION Use an isolation transformer when performing any service on this chassis. Before removing the anode cap, discharge electricity because it contains high voltage. When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. When you exchange IC and Transistor for a heat sink, apply the silicon grease (YG6260M) on the contract section of the heat sink, Before applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.) Prepare the following measurement tools for electrical adjustments. 1. Oscilloscope 2. Digital Voltmeter 3. Pattern Generator On-Screen Display Adjustment 1. In the condition of NO indication on the screen. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 1 second to appear the adjustment mode on the screen as shown in Fig. 1-1.
2. BASIC ADJUSTMENTS
2-1: CONSTANT VOLTAGE 1. 2. 3. 4. Place the set with Aging Test for more than 15 minutes. Set condition is AV MODE without signal. Connect the digital voltmeter to the TP401. Using the adjustment control, set the brightness and contrast to normal position. 5. Adjust the VR502 until the digital voltmeter is 140 0.2V. 2-2: CUT OFF 1. Adjust the unit to the following settings. R.DRIVE=64, B.DRIVE=64, R.BIAS=64, G.BIAS=64, B.BIAS=64, BRI.CENT=90, CONT.MAX=100. 2. Place the set with Aging Test for more than 15 minutes. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select "CUT OFF". 4. Adjust the Screen Volume until a dim raster is obtained. 2-3: FOCUS 1. Receive the monoscope pattern. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct. 2-4: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set with Aging Test for more than 10 minutes. 2. Receive the white 100% signal from the Pattern Generator. 3. Using the adjustment control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (10) on the remote control to select "R.BIAS". 5. Using the VOL. UP/DOWN button on the remote control, adjust the R.BIAS. 6. Press the CH. UP/DOWN button on the remote control to select the "R.DRIVE", "B.DRIVE", "G.BIAS" or "B.BIAS". 7. Using the VOL. UP/DOWN button on the remote control, adjust the R.DRIVE, B.DRIVE, G.BIAS or B.BIAS. 8. Perform the above adjustments 6 and 7 until the white color is looked like a white. 2-5: VERTICAL SHIFT, VERTICAL LINEARITY 1. Receive an 70dB monoscope pattern. 2. Using the adjustment control, set the brightness and contrast to normal position. 3. Check the step No. V. SHIFT is "00" 4. Adjust the VR401 until the horizontal line becomes fit to the notch of the shadow mask. 5. Adjust the VR402 until the SHIFT quantity of the OVER SCAN on uside and downside becomes minimum. 2-6: VERTICAL SIZE 1. Receive the crosshatch signal from the Pattern Generator. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (06) on the remote control to select "V.SIZE". 3. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes 10~11%. 4. Receive a broadcast and check if the picture is normal. D-1
TV
00 OSD
17 Fig. 1-1
2. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 3. Press the MENU button on the remote control to end the adjustments.
NO. 00 01 04 05 06 07 08 09 10 11 12 13 14 15 FUNCTION OSD H CUT OFF H.VCO H.PHASE V.SIZE V.SHIFT R.DRIVE B.DRIVE R.BIAS G.BIAS B.BIAS BRIGHT CENT BRIGHT MAX BRIGHT MIN NO. 16 17 18 19 20 21 22 23 24 25 26 27 28 29 FUNCTION CONTRAST CENT CONTRAST MAX CONTRAST MIN COLOR CENT COLOR MAX COLOR MIN TINT SHARPNESS FM LEVEL LEVEL SEPARATION 1 SEPARATION 2 TEST MONO TEST STEREO
Fig. 1-2
ELECTRICAL ADJUSTMENTS
2-7: OSD 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-1) 2-11: SEPARATION 1, 2 Please do the method (1) or method (2) adjustment. Method (1) 1. Set the multi-sound signal generator for each different L-ch and R-ch frequency (Ex. L-ch=2KHz, R-ch=400Hz) and receive the RF. 2. Connect the oscilloscope to the pin 6 and pin 7 of CP601. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (26) on the remote control to select ''SEP 1''. 4. Press the VOL. UP/DOWN button on the remote control to adjust it until the audio output wave becomes a fine sine wave. 5. Press the CH UP button once the set to "SEP 2" mode. Then perform the above adjustment 4. Method (2) 1. Set the multi-sound signal generator L-ch=1KHz, R-ch =Non input and receive the RF. 2. Connect the oscilloscope to the pin 6 and pin 7 of CP601 3. Press the AUDIO SELECT button on the remote control to set to the stereo mode. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (26) on the remote control to select ''SEP 1''. 5. Press the VOL. UP/DOWN button on the remote control to adjust it until the R-ch output becomes minimum. 6. Set the multi-sound signal generator L-ch=Non input, R-ch=1KHz and receive the RF. 7. Connect the oscilloscope to the pin 6 and pin 7 of CP601 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (27) on the remote control to select ''SEP 2''. 9. Press the VOL. UP/DOWN button on the remote control to adjust it until the L-ch output becomes minimum. 2-12: HORIZONTAL PHASE 1. Receive the center cross signal from the Pattern Generator. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (05) on the remote control to select "H.PHAS". 3. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum.
TV
17 B
Fig. 2-1
1. Receive an over 70dB monoscope pattern. 2. Connect the AC voltmeter to the pin 6 of CP601. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (25) on the remote control to select "LEVEL". 4. Press the VOL. UP/DOWN button on the remote control until the AC voltmeter is 80 2mV. 2-9: SUB BRIGHTNESS 1. Receive an over 70dB monoscope pattern. 2. Using the adjustment control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (13) on the remote control to select "BRI.CENT". 4. Press the VOL. UP/DOWN button on the remote control until the screen begin to shine. 5. Press the TV/AV button on the remote to set to the AV mode. Then perform the above adjustment 2~4. 2-10: CONTRAST MAX 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select "CONT MAX". 4. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "100". 5. Receive a broadcast and check if the picture is normal. 6. Receive the color bar pattern. (Audio Video Input) 7. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~5.
D-2
ELECTRICAL ADJUSTMENTS
2-13: SUB TINT/SUB COLOR 1. Receive the color bar pattern. 2. Connect the oscilloscope to TP024. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select "TINT". 4. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes as straight line (Refer to Fig. 2-2) 5. Connect the oscilloscope to TP022. 6. Activate the adjustment mode display of Fig. 1-1 and press the channel button (19) on the remote control to select "COL.CENT". 7. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 110 10% of the white level. (Refer to Fig. 2-3) 8. Receive the color bar pattern. (Audio Video Input) 9. Press the TV/AV button on the remote control to set to the AV mode. 10. Connect the oscilloscope to TP024. 11. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select "TINT". 12. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes as straight line (Refer to Fig. 2-4) 13. Connect the oscilloscope to TP022. 14. Activate the adjustment mode display of Fig. 1-1 and press the channel button (19) on the remote control to select "COL.CENT". 15. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 110 10% of the white level. (Refer to Fig. 2-3)
"A"
Fig. 2-4 2-14: Confirmation of Fixed Value (step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. NO. 04 14 15 16 18 20 21 23 24 28 29 FUNCTION H VCO BRIGHT MAX BRIGHT MIN CONT CENT CONT MIN COLOR MAX COLOR MIN SHARPNESS FM LEVEL TEST MONO TEST STERIO RF 04 130 70 35 25 65 00 45 01 00 00 AV 04 130 70 35 25 65 00 45 01 00 00
Fig. 2-3
D-3
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-2: PURITY NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue colors. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 3-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB RGB
R G B
R G B RIGHT/LEFT SLANT
WEDGE
WEDGE
D-4
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CRT PCB
J801
CP806
CP
80
CP802B CP803B
CR
CD
80
CD802
CD803
CR T
VR401
FB401
CP 401
VR502
TP401
EG
AU
SS
IL
CP1001
CD1001 SPEAKER
C P5
02
CP802A
J712
J711
J710
MAIN PCB
D-5
BLOCK DIAGRAM
J705 3
CH. DOWN VOL. DOWN CH. UP VOL. UP POWER 67 68 OS101 1 78 69 70
I/O IIC TIM INT PWM AD
7
4 6
12 8 6
1 9
16
NC 20 29 30
14
3
5
13
RGB Proc.2 OSD SW CONTRAST BRIGHTNESS
Chroma Proc. ACC/C-BPF APC/KILLER TINT/DEMO
Q801, Q804
RGB OUTPUT Stage DRIVE CUT OFF HV BLK
50 51 52
MCU CLK
Q607
H.CTL
Hor.Proc. SYNC SEPA/Hor. VCO Hor.COUNT DOWN AFC-1/H COINCIDENT AFC-2 H PHASE
46 45 Q402 H. DRIVE Q401
VCXO
H. OUTPUT
57
37 38
16
X601 3.579545MHz
11
B Heater
6
G
8
R CRT
IC501 LTV-817M-VB
FEED BACK Q502 BUFFER Q501 SWITCHING
V-OUT IC IC401 LA78041 Q507 FEED BACK SW 1 2 4 5 6 MEMORY IC SDA SCL IC199 S-24C04BDP-LA PUMP UP AMP + 7 1 VCC 2 6 5 FB401 9 1 2 F S HV DY
10
RY501 RELAY
10
J707
2 J701 3 30 3 4 6
5 3
2
J710
F501 TH501
SPEAKER SP1001
2 2
AC IN J711
16 19
12 9 7
E-1
E-2
OS101
SW105
C123
W132
J712 C701
W042
W043
6.3A125VOR250V F501
SW101
SW104
SW103 W036
R124
W041
W040
R605
W037
W853
FH501 S501A
C8
TP022
02
W010
W009
J801
R6
Q607
29_
1
Q608 D604 Q603 W007 W815 Q602 W008 W006 W005 Q610 W002 W003 W139
W035
R500 CP503
P8
CD501
06
803
R1522 TP023
R608
W034 C653
S501B Q806
C1524
C630 Q606
C620
R606
D603
C632_1
R80
7
Q804
R806 Q805
C621
W004
C624
TH
D501 D504
C530_1 D502 S801X C502 Q502 C507 HS501 IC501 Q507 D528 R547 D525 FB401 W821 C512 C522 VR502
50 1
C533_1 C506
W847 R817 C1527_2 R1524 C1505 D1502 R1519 W103 Q1508 D1501 W104 W053 C712 W102 W101 C706 C718 C633 D803
C617
C628
C623
W019
C652
D801
D802
C P5 02
C503 RY501 R503 D503 D509 R501 W870 ICP501 D508 R512 B501 C509 W830 D521 C514_1 S802X R507 S801Y Q501 D506 R543 R554 W849 C504 C520_1 R514 R555 W135 D515
W015
R812
Q802 R818 D516 S802Y T501 D523 W133 R508 R504 TP401 C511_1 C402
Q801
W100
R702
W052
IC702
W116
W099 C732
C610
CP
R132
C719
W115
C601
W114
C103_1
W013
W836
C501
Q702
W810
W012
Q601
R125
W141
C1008
R516
CP1001
W839 R001
R5
C521
21
D417 C513_1
D511
R1009
W834
C518
W142
W829
C1009
W148
C1017
C455 Q402_1
C440 W061
W062
C1016 C1013
C1014
W837
R446
C52 8
R1004
C414
D419 D412
R402 W121
R51 9
C453 W134 L401 R450 D407 W136 R421_1 C420 D410 C401 R422
C1018_1
R1015
W147 W020
W126 D418 R418 HS401 C403 R434 Q401 W124 D406 IC401 R435 R417 W081 C417 W861 C449 W122 C452_1 C433 W123
R1010
C911
C910
C915
C907
C905
C903 R006
W082
C904
W032
W031
W078
W077
W080
W079 W868
W150 C921
C412
R419
W110
R439
C316
W874
R308
R423
R420
C345
C303
C324
CP 401 _1
C315
W119
C302
R433
R412
C328
C317
W149
W094 R410 R415 W131 R411 W130 R408 VR401 W093 W092 W091 W088 W087 W085 C721 D404 Q707 J707 C705 Q705 R721 C726
C322
C321 W089
TU001
W027
C325
C002
C704 W086
C729
C722_1
C730
C720
C727
CP601
J701
D411 C434
C728
J705
D405
CD803A CP803A
W127
R720
F-1
F-2
F-3
R903 C716_1 R908 R601 C647 C603 IC901 R604 C609 25 C913 C1004 C918 C917 C912 C914 C916 C908 R905 R909 R733 R902 R901 R907 C327 R319 C005 C001 C006 R004 R003 R728 R724_1 R707 R723 IC302 C343 R1006 C724_1 C344 C323 R711 C307 C301 R314 C309 R726 R725 R722 R734 C604 C715_1 C102 R607 41 R120 C113 R103 C107 C104 R102 C108 C105
IC 10
C1007
1
1
C629
C318 C319
R123 R113 R115 R131 R112 R110 R105 R616 R617 R106 R109 C101
R621 R712 C1520 R1523 R1512 R715 R1521 C1521 R1520 IC1502 R731 R710 R1518 C707 C708
R703 R704
C408 R437
SOLDER SIDE
R128
C811 C810
R816 C813
F-4
B
0 1 2 E1 0 3 E2 0 4 VSS 0
E0
MODE
VCC
8 4.9
7 0
6 4.8
SDA 5
SCL
27K
4.8
R617
W828
P.CON+5V
W823
H_OUT
H_CTL
8.2K
1/4W
1K
R618
R620
B.OUT
7
C101 TM101 RC-GT010 0.01 F
H_SYNC
FROM/TO DEFLECTION/CRT R608 100 1/4W C653 50V 1 YK CLAMP V_OUT GND V_FEEDBACK ABCL P.CON+8V[B] W847 H_OUT X-RAY R.OUT UNREG+12V G.OUT B.OUT H_SYNC
H_CTL
ABCL
G.OUT
R.OUT
11E1-EIC
C632_1 100 1/4W 100 1/4W 100 1/4W R610 5.6K 10V 470 YK C630 10K 1/4W 16V 100 KA R609 120K C629 0.01 F R627 10K
D606
R616 6.8K
R615
R614
R613
R611
C628
C627
C624
41 NC 42 HVCO F/B 43 AFC FILTER 44 DEF GND 45 FBP IN 46 H OUT 47 DEF VCC 48 NC 49 HI VCC 50 R OUT 51 G OUT 52 B OUT 53 ACL 54 NC 55 PROTECT 56 SDA 57 H_CTL 58 SCL 59 NC 60 NC 61 NC 62 DEGAUSS_H 63 STANDBY_H 64 VOLUME 65 NC 66 AFT 67 KEY1 68 KEY2 69 POWER_ON 70 REMOCON 71 AV2 72 AV1 73 AUDIO_MUTE 74 X-RAY 75 IIC_OFF 76 ON_TIMER 77 SYNC 78 POWER FAIL 79 X-RAY_TEST 80 EXT_MUTE AT+5V R125 R131 2.2K R123 2.2K R113 2.2K R115 22K
SDA SCL
C626
R108 R107
100 1/4W 100 1/4W R106 3.3K R130 0 22K 1/4W 64 0 65 4.8 66 4.9 67 4.9 68 4.9 69 4.9 70 4.9 71 4.9 72 4.9 73 1.8 74 R127 4.9 75
50V 1 KA
47K
0.01 F
0.01
1 MKT
7.9 C623 16V 100 YK 7.9 8.5 11.3 8.5 11.3 8V REG Q606 KTC3203_Y
5 VSS 6 MCU VCC 7 TEST0 8 FILT 9 HLT 10 VHOLD 11 CVIN 12 RESET IN 13 MCU RESET OUT 14 Y SW OUT 15 V/C GND 16 3.58 XTAL
0 63
0 62
0 61
0 60
0 4.8 59 58
0 5.1 57 56
0 3.5 3.7 44 43 42
ON_TIMER R112 AFT KEY1 KEY2 POWER_ON REMOCON AV2 AV1 AUDIO_MUTE X-RAY 100K
R607 100
6
FROM/TO POWER POWER_FAIL C652 UNREG+12V +B 50V 0.22 KA DEGAUSS_H GND
39
MCU GND PGB OUTPUT Stage DRIVE CUT-OFF HV BLK Hor.Proc. SYNC SEPA/Hor.VCO Hor.COUNT DOWN AFC-1/H COINCIDENT AFC-2 H PHASE Ver SYNC SEP Ver.COUNT DOWN V RAMP
4
V_OUT R606 22K V_FEEDBACK
ROM RAM
37
SDA/SCL OSD
38
1/4W
36 I/O 34 RGB Proc.2 OSD SW CONTRAST BRIGHTNESS RGB Proc.1 RGB MATRIX COLOR CONT 35
17 C-APC 18 MCU5.7V REG OUT 19 NC 20 CVBS IN3 21 AUDIO IN3 22 V/C VCC 23 MCU TEST 24 CVBS IN2 25 AUDIO IN2 26 CVBS IN1 27 AUDIO IN1 28 5.7V REG OUT 29 C(Y/C) IN
32
P-ON CONT
33
0.01 F
1K 1/4W
0 NC 0 NC 4.9
CLK CONT
MCU CLK
31
76
77
ATT 27
78
0 79 4.8 80
VCO 26 XO VCXO 25
30 Y(Y/C) IN 31 VREG VCC 32 FSC OUT 33 MONITOR OUT 34 AUDIO ATT OUT 35 AUDIO ATT FILTER 36 NC 37 V RAMP F/B 38 V RAMP OUT 39 V RAMP CAP 40 8.7V REG OUT
1 0
2 4.8
3 NC
4 5.0 4.9
5 0 C102 0.01 F
6 4.9
7 0 C104
9 0 50V 1 KA C108
10 0.2 0.001 B
11 2.8
12 4.9 C601
14 2.5
15 0 X601
16 3.3
17 2.9 R602
18 5.5
19 NC 0 100 1/4W
20 NC 1.9
21 NC
22 2.3 5.1
23 0
24 NC 1.9
1 2
NC NC C002
C001 0.01 F
STEREO+5V C_IN GND W815 FROM/TO SOUND TUNER+5V TU_AUDIO AUDIO_OUT_L SCL SDA GND AUDIO_MUTE STEREO+5V P.CON+8V[B] AUDIO_OUT_R TEST POINT CP601 TKC-M07X-A1 R004 AUDIO_OUT_R SCL SDA AFT AUDIO_OUT_L IIC_OFF SDA SCL TU_AUDIO AUDIO_R AUDIO_L GND IIC_OFF SDA SCL GND 7 6 5 4 3 2 1
6.3V 1000 YK
W809
10V 470 YK
R102
560P CH
470 C113
0.1 F
R120
C603
C606
10V 220 YK
C103_1
470P B
R103 1K
C609 0.01 F
C105
C107
8.2K 50V 1 KA
C605 0.022 F
220P B
1M 1/4W
R104
C604
POWER_ON
REMOCON
KEY2
KEY1
W810
AT+5V
R601
R003 100 11 100 12 5.5 4.9 R603_1 8.8 120 1/2W 13 100 1/4W 14 15 0.022 F 16 NC C004 R006 NC R001 560 1/4W 68K 1/2W R002 68K 1/2W R005
R143 16V 10 KA
47 1/4W C123
R128
560 R126 2.7K VOL DOWN SW101 EVQ21505R SW103 EVQ21505R CH DOWN SW102 EVQ21505R VOL UP
2
+B
R101
560 1/4W SW104 EVQ21505R SW105 EVQ21505R
4.9
4.8
POWER
CH UP
MTZJ33B
TU001 ENG36A01G
20
B+ 3
GND 2
17 D001
21
Vout
OS101 RPM7138-H5
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
ETANT ATTENTION:LES PIECES REPAREES PAR UN SECURITE DANGEREUSES AN POINT DE VUE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
ARE
R.SIGNAL G.SIGNAL B.SIGNAL DEFLECTION SIGNAL AUDIO SIGNAL TUNER VIDEO SIGNAL
G H
G-1
G-2
180V
R811
2.7K
25V 1000 YK
11E1-EIC C414
D412
R412
270 1/2W
MTZJ33B
1 1/2W
R419
C418
R407
R436
D418
GND
1 1/2W
C403
18
R437 2.7K
6.8K 1/4W
2
C433 35V 2200 YK
MTZJ33B
1 1/2W
27K 1/4W
V-LINER
3.2 100.6
3.2 98.4
3.2 95.4
1 1/2W
1/2W
D419
2.7
560P CH 68 1/4W R813 R812
2.7
560P CH 68 1/4W R816 R817
2.7
560P CH 68 1/4W R815 R818
R434
R435
C417
GND
R433
R406
270
270
1SS133
1SS133
D801
D802
D803
5.9
5.9
1SS133
11 6 8 10 9
B G R
C811
C810
C809
270
5 7 1
2.7K
R814
R420
1.2K
1.2K
19
CD801 CU822501
130.6
130.6
R801
220
R808
R810
220
C452_1
220
V801 A68AJB82X10
TP022
20 C449 1/4W
TP023
22 2.7K 1/4W
TP024
21 2.7K 1/4W
12K 2W
MTZJ5.1B
3.9K +-1%
R802
R803
D404
R408
100V 22 YK
C434
W861
X-RAY R424
D411
AU02A-EIC
R429_1
18K +-1%
FB401
1 1W
1K 1W R402 C402
112.0
2KV 0.001 R
ELH5L4113
15
L401
COL
17
T401 ETH19Y203AY 5 1 4 H.OUTPUT Q401 2SD2499(LBOEC1)
128.0 128.0
6 2 9
VIDEO B+
F S GND 11 ABL 7
12K 2W
R807
TO MICON/CHROMA/TUNER
2.7K
R806
R805
250V 0.47
PMS
12K 2W R804
4
C801 FORCUS SCREEN 1 CP806 005P-2100 330P CH
470P MPP
470 1/2W
16
2
114.0 0
100 1/4W
R446
C453
R427
1.25KV
0
D405 MTZJ9.1B C401 500V 100P B
GND GND 8 E8
HS401 763WAA0214
-27.0 5 NC
2KV 0.001 B
3
27.0 0.3
H.DRIVE Q402_1 KTC3227_Y
6.4 9 0 101.6
F
0 6 4
500V 0.0022
AU02A-EIC
D410
C420
2
FROM POWER UNREG+18V B_SHORT +B GND D417 11E1-EIC B+ +B TP401
99.6
250V
10
YK
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. D
ETANT ATTENTION:LES PIECES REPAREES PAR UN SECURITE DANGEREUSES AN POINT DE VUE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
ARE
G-3
G-4
(TV MT PCB)
RELAY DRIVE Q504 KTC3198 0.2 0.6 0 TO DEFLECTION/CRT
D516 1SS133
10K 1/4W
R515
2 3
RY501 ALKS321 T501 8140065S 9 P1 7 ICP501 20N_5000FSW R501 140.5 6 144.0 5 P2 11 0 12 NC 11.6 2.7M 1/4W 13 11.7 3 0 2 W870 11.8 1 16 W836 C521 15 W5RH3.5X5X1.0 0 160V 220 YXF FE201-6L49 14 95.4 B504 0 C517 2KV 0.0027 D510 R W851 D505 30DF6-FC 10 15.6 NC 15.6 W848 C516 500V 0.0022 B 35V 1000 YK 126 KX 8 KX 5A 250V C533_1 140.5 2.7M 1/2W +-10%
C530_1
R500
0.001
0.001
250V
CP502 A1561WV2-2P
250V
C501
CP503 003P-2100
1.2 RM11C-EIC RM11C-EIC D502 TH501 B59203-S1060-B14 COIL LINE FILTER L501 2R2A752F28Y ECQUL ECQUL
7W R503
6
FROM/TO AV GND
D501
MTZJ18B
1/2W
3 1
4 C506 2
C507
FROM/TO COMB FILTER GND 50V 22 YK MTZJ5.1B R516 1/4W C513_1 FROM/TO MICON/CHROMA/TUNER UNREG+12V DEGAUSS_H POWER_FAIL D511
C505_2
275V 0.22
R520
D509
275V 0.1
1.5M
250V
0.0022 KX
W5RH3.5X5X1.0
B501
1N4937
5.6K
S801X 6.3A125V
C527
C528
100 1/4W
R508
1SS133
W830
D508
S501A 144.0 D R543 G 4.8 2KV 0.0012 R C514_1 SWTCHING 0.1 S Q501 2SK3326(2) 330 1W R512 10K 270 1/4W D521 CH S802X 1SS133 470P S801Y C511_1 1/2W S501B C509 100V 0.047 MMTS C522 0.01 B R504
1SS133
1K 1/4W
1SS133
R532
820
D517
0.15 1W
D506
MTZJ18B
R519
4.8
25V 47 YK
W821
C519
NC
100V 0.01
+B ADJ
VR502 22K
27K
S802Y
R554
1K
R534
1/4W
100K 1/4W
MTZJ8.2B
D525
D518
500V 470P B
1SS133
MTZJ4.7B
C518
D514 D515
+B
GND
WHITE
R507
R555
HS501 763WAA0023
5.4
MTZJ5.6B
D528
6.3A 125V
5A 250V
REPLACE ONLY WITH THE SAME TYPE FUSE 6.3A 125V(F501)AND 5A 250V(ICP501).
LES RISQUES ATTENTION:POUR UNE PROTECTION CONTINUEMEME TYPE DINCEIE NUTOLISER QUE DES FUSIBLE DE
6.8K
R514
1/4W
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
ETANT ATTENTION:LES PIECES REPAREES PAR UN SECURITE DANGEREUSES AN POINT DE VUE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
ARE
G-5
G-6
C316
7
50V 10 KA C919 C301 26 3.2 2.3 BUFFER Q901 KTA1266 0 R902 R905 39K 220 C920 50V 1 KA C921 TONE CONTROL IC IC302 AN5891SA-E1V 50V 1 KA 0.047 B C914 0.1 F C917 F C912 0.1 27 0.033 B
R319 1K
50V 0.1 KA
R909
R907
R901
0.015 B
C307
C315
50V 10
220
56K
56K
7
YK C345 50V 10 C324 2.8 15 16 Balance /MUTE 50V 10 0 YK VD L ONT
50V 10 YK
0.033 B
C343
C303
C344
C309
0.01 B
4.1 1 PF1 2
1.9 3 AGC
4.1 L IN
4.2 10 LT
4.2 11 LB
NC
0 12 NC
NC
0 13 NC
2.0 14 BD
3.2
AGC
SURR
Tone Control
R908
39K
2.3 22
2.3 21
OUT SW
2.3
DAC
NC 20
0 19
5.0 18
5.0
GND
0 17 16
3.7 15
St.PLL
3.6 14
Det Pilot Filter Noise Filter Spectral RMS Det Spectral
2.6 13
Det SAP VCA Input
3.7
ZAP IIC Decoder L-R Filter L+R Filter L-R Demod L+R Demod
6
SDA 18 0 SCL 17 4.8
KA
0.01 F
C321
50V 10 YK
50V 0.33 KA
C325
50V 4.7 KA
25V 10 KA
R903
220K
C907
C915
16V 100 YK
50V 0.1 KA
50V 4.7 KA
C322
50V 4.7 KA
C903
0.001 B
0.022 B
0.1 F
C905
C908
C913
C916
W875
W868
FROM/TO AV REAR_AUDIO_R REAR_AUDIO_L 100uH 0305 FRONT_AUDIO_R FRONT_AUDIO_L AUDIO_OUT_R AUDIO_OUT_L L902
W874 W869
GND
C332
50V 10 YK
50V 10
0.01 F C328
C302
C327
100P CH
0.1 F
C904
C911
C918
YK
C319
GND
50V 3.3 KA
100P CH C318
2.3
2.3
2.2
2.2
0.4
5.1
2.4
2.4
0.4
2.3
3.4
50V 1
C323
10
11
12
C320
FROM/TO DEFLECTION/CRT
Vcc
50V 10 YK
Expand Spectral
Det Noise
L301
100uH 0305
Switch De-Emph (L-R)/SAP 75us Filter Cancel SAPout Offset Expand Cancel Wide Band Offset
Cancel Pilot
Demod SAP
50V 10 YK
Filter Stereo
Filter SAP
R IN
Vref
NC 27 0 NC
BB 26 4.1
RB 25 4.2
RT 24 4.2
BLD 23 3.0
NC TD 22 21 2.0 0 NC
4
SOUND AMP IC R1014 5.6K IC1001 AN5276 + + NC CH1 IN 1 2 ATT. + RIPPLE FILTER CH2 GND RF IN 3 4 5 0 17.6 0 1.0 + ATT.CONT.
5.6K
GND 9 0.3 0
STAND CH1 VCC -BY OUT 10 11 12 18.9 8.7 16.8 C1009 CP1001 A2502WV2-4P SP OUT R+ 25V 1000 YK SP OUT RW853 SP OUT LSP OUT L+ 1 2 3 4 1 2 3 4 SPEAKER SP1001 S0509F12-D 8 OHM SPEAKER SP1001 S0509F12-D 8 OHM
NC
500V 470P B
25V 100
C1016
C1004
R1006
R1008
1.8K
1.8K
0.01
16V 47
HS1001 763WAA0160
C1014
YK
50V 2.2
0.01 F
33 32 W834
2
R1002 4.7K
C1017
10 KA
2
W837
16V
PCB010 TMC567
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
ARE
ETANT ATTENTION:LES PIECES REPAREES PAR UN SECURITE DANGEREUSES AN POINT DE VUE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
AUDIO SIGNAL
G-7
G-8
(TV MT PCB)
Y_IN
VI_C_IN
VIDEO_OUT VI_Y_IN S_VIDEO AV/S SW IC IC1502 NJM2283M C1505 50V 4.7 KA R1512 1K 2 7.5 4.5 N L 15 16 1 4.5 0 C1521 4.5 14 3 N 13 4 5.0 7.5 12 5 L 11 6 10P CH R1520 1K C1527_2 16V 10 KANP FROM MICON/CROMA/TUNER AV1 ON_TIMER 4.5 0 FROM/TO POWER 4.5 9 R1524 KA 1K 1/4W C1524 GND GND ON_TIMER GND
5
R1523 1K W807 C1520 56P CH R1521 820
3.8 0
3.8 3.8
1K 1/4W
R1522
4.5
10
7.5
R1518
R1519
1/4W
560
560
16V 10
D1502 1SS133
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
PCB010 TMC567
G-9
G-10
AV SCHEMATIC DIAGRAM
8
(TV MT PCB)
R733
C702 16V 10 KA
NC
VIDEO_3_IN
7
R734 1K R740
NC
C701 16V 10 KA
1K
7
2 AV (FRONT) J711 HTJ-032-03AW
H
L3_IN
0.0033 B
C715_1
C716_1
0.0033
75
NC
R3_IN
R707
1.2K
C729 50V 10 YK C720 16V 47 YK R725 R727 3.3K 1/4W 8.2K 1/4W R729 1.5K BUFFER Q701 KTC3198 2.5 C730 0.8 16V 47 YK R731 16V 47 YK R728 R710 C719 1.5K 1K 2.2K 2.5 1.8 C732 5.0 BUFFER Q702 KTC3198
GND
75
1.6
R722
75
VIDEO AMP IC
IC702
NJM2246L
0.1
SW1 2
Vin2 3 5.0
V+ 6 9.0
Vout 7 4.0
5.9
16V 10 KA
C706
C718
C712
C707
10
16V
0.1
4
REAR_AV-IN (STEREO) J701 MSP-213V2-432_PBSN
H1 NC H1 H2
C717
TU_VIDEO 16V 10 KA R711 1K R709 1K C704 R702 16V 10 KA 10 1/4W C703 16V 10 KA R720 R721 1K 1/4W R719 0.0033 B 0.0033 B 75 10V C721 470 YK R760 390 1/4W MUTE Q705 KTC3198 0 0 0 MUTE 0 Q707 KTC3198 0 1K 1/4W C728 16V 10 KA C726 16V 10 KA FROM/TO COMB FILTER
3
A_OUT_R A_OUT_L V_OUT
3
ON_TIMER S_VIDEO VI_Y_IN VIDEO_IN VI_C_IN
H2
H1
C723_1
5.2 C724_1
R712
75
V1_SW
VIDEO_OUT GND
PCB010 TMC567
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
G-11
G-12
WAVEFORMS
MICON/CHROMA/TUNER
20V 20s/div
7 1V 20s/div
17 200V 20s/div
200mV 20s/div
8 200mV 20s/div
18 10V 5ms/div
DEFLECTION/CRT
0.5V 5ms/div
14 0.5V 5ms/div
19 10V 5ms/div
1V 20s/div
15 20V 20s/div
20 50V 20s/div
6 1V 20s/div
16 2V 20s/div
21 50V 20s/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-1
WAVEFORMS
22 50V 20s/div
31 200mV 1ms/div
SOUND
25 0.5V 1ms/div
32 0.5V 1ms/div
26 200mV 1ms/div
33 0.5V 1ms/div
27 200mV 1ms/div
28 200mV 1ms/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-2
106
206 206
112 206
206
108
207
109
205
109
J801 207 207
102
206
105
206 108 207 110 FB401 202 204 204 202 TU001
203 103 104
109
V801
109
201
201
SP1001
111
203
101B
204
107
101C
101
101A
I-1
DESCRIPTION
CABINET,FRONT ASS'Y CABINET,FRONT GUIDE,REMOCON BADGE,BRAND BUTTON,ASS'Y CABINET,BACK ASS'Y FELT,SHEET FELT SHEET SPRING,EARTH SHEET,RATING SHEET,CAUTION FELT,SHEET HOLDER,CRT WIRE
5x30xT0.5 5x150xT0.5
18x350xT=0.5
899HV3T000 HOLDER,ANODE WIRE 8995034000 CORD CLIP UL CO. 800WQ00066 FELT,SHEET 8107630804 8109I30A04 8109630802 8110630A24 8110630A04 8117540B04 8141J50D54 791AHA0026 792AHA0101 792AHA0102 793ACDA172 J3N42401A JB5L0100 A3N424E975 SCREW,TAP TITE(S) SCREW,TAP TITE(B) SCREW,TAP TITE(B) SCREW,TAP TITE(P) SCREW,TAP TITE(P) SCREW,TAPPING(B0) SCREW,TAP TITE(P) FILM,BAG PACKAGE,BOTTOM PACKAGE,TOP GIFT BOX INSTRUCTION BOOK POLYBAG,INSTRUCTION INSTRUCTION BOOK KIT BRAZIER WH7 BRAZIER BRAZIER BRAZIER TRUSS GW20
J1-1
DESCRIPTION RESISTORS
R,METAL OXIDE RC RC RC RC R,FUSE RC R,METAL OXIDE RC R,CEMENT R.METAL OXIDE R,METAL OXIDE RC R.METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE 1K OHM 1W 330 OHM 1/4W 6.8K OHM 1/4W 82K OHM 1/4W 82K OHM 1/4W 1 OHM 1W 1 OHM 1/2W 68 OHM 1W 2.7M OHM 1/2W 1.2 OHM 7W 0.39 OHM 2W 0.15 OHM 1W 1.5M OHM 1/2W 150 OHM 2W 330 OHM 1W 27 OHM 3W 12K OHM 2W 12K OHM 2W 12K OHM 2W
DESCRIPTION DIODES
DIODE SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON 1N4937 MTZJ8.2B T-77 MTZJ5.6B T-77 1SS133T-77 MTZJ8.2B T-77 11E1-EIC 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 OEC7091A S-24C04BDP-LA AN5891SA-E1V LA78041 LTV-817M-VB NJM2246L AN5829S AN5276 NJM2283M 2SD2499(LB0EC1) KTC3227_Y-AT 2SK3326(2) KTC3203_Y-AT KTC3198-AT(Y,GR) KTC3198-AT(Y,GR) KTC3203_Y-AT KTC3209_Y-AT KTC3203_Y-AT KTC3203_Y-AT KTC3198-AT(Y,GR) KTC3209_Y-AT KTC3203_Y-AT KTC3198-AT(Y,GR) KTC3198-AT(Y,GR) KTC3198-AT(Y,GR) KTC3198-AT(Y,GR) KTA1266-AT(Y,GR) KTC3198-AT(Y,GR) KTC3199_Y-AT KTC3199_Y-AT KTC3199_Y-AT KTC4217(O,Y) KTC4217(O,Y) KTC4217(O,Y) KTA1266-AT(Y,GR) KTA1266-AT(Y,GR) KRC102MAT 100 UH ELH5L4113 2R2A752F28Y 8R270010 100 UH ETH19Y203AY 8140065S MSP-213V2-432 PBSN YKF51-5503 MSP-213V1-432 PBSN HTJ-032-03AY HTJ-032-03AW HTJ-032-03AR ISHS53S EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVNCYAA03BE3 EVNCYAA03BQ2 EVNCYAA03BE4
or
! ! ! ! ! !
ICS
IC IC IC IC PHOTO COUPLER IC IC IC IC
! ! !
CAPACITORS
! ! ! ! CC CC CP CE CC CE CMPP CMPP CMPP CE CMP CMP CE CE CE CC CC CC CE CC CC CE CC CC CC CC CE 0.001 UF 2KV R 150 PF 50V CH 0.033 UF 50V 1000 UF 25V 0.0022UF 500V B 2200 UF 35V 0.47 UF 250V PMS 0.015 UF 1.25KV 470 PF 1.25KV 1000 UF 35V 0.22 UF 275V ECQUL 0.1 UF 275V ECQUL 470 UF 200V 47 UF 25V or 47 UF 25V 0.0012UF 2KV R 0.0027UF 2KV R 470 PF 50V CH 220 UF 160V 0.01 UF 50V B or 0.01 UF 50V B 2200 UF 16V 0.0022UF 250V 0.001 UF 250V 0.001 UF 250V 0.001 UF 2KV B 2200 UF 35V
TRANSISTORS
TRANSISTOR SILICON TRANSISTOR SILICON FET TRANSISTOR, SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR, SILICON TRANSISTOR SILICON TRANSISTOR, SILICON TRANSISTOR, SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR, SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR COIL COIL,LINEARITY COIL,LINE FILTER COIL,DEGAUSS COIL TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING
! ! ! !
C514 C517 C519 ! C521 C522 C527 C528 C530 C533 C802 C1016 D001 D404 D405 D406 D407 D410 D411 D412 D417 D418 D419 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D511 D512 D514 D515 D516 D517 D518 D521
DIODES
DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE,ZENER DIODE,ZENER DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE RECTIFIER DIODE,ZENER DIODE SILICON DIODE,SILICON DIODE,ZENER DIODE SILICON DIODE,ZENER DIODE SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON MTZJ33B T-77 MTZJ5.1B T-77 MTZJ9.1B T-77 11E1-EIC AU02A-EIC AU02A-EIC AU02A-EIC 11E1-EIC 11E1-EIC MTZJ33B T-77 MTZJ33B T-77 RM11C-EIC RM11C-EIC RM11C-EIC RM11C-EIC 30DF6-FC MTZJ18B T-77 11E1-EIC 1SS133T-77 MTZJ18B T-77 FE201-6L49 MTZJ5.1B T-77 SB290S 1SS133T-77 MTZJ4.7B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77
! !
COILS &TRANSFORMERS
JACKS
RCA JACK JACK RCA JACK RCA JACK RCA JACK RCA JACK SOCKET,CATHODE RAY,TUBE
! ! ! !
SWITCHES
SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT
! ! !
VARIABLE RESISTORS
V1163H3BTC VOLUME,SEMI FIXED V1163Q2BTC VOLUME,SEMI FIXED V1163H4BTC VOLUME,SEMI FIXED
J2-1
MISCELLANEOUS
024HT03553 024HT03553 1209415911 06CU822501 WDL6052038 WBL6038038 069W340018 069S420110 069D01001A 0697270650 069S320010 069W010010 069S140419 067U006049 067U006049 067U004029 067U004029 124116281A 124120301A 081PC6R305 043227009R 06710T0006 06710T0006 0835A05005 0773071001 0560V20115 070Y435005 D8EE0B1400 076N0GT010 0163100002 098T270601 100CT3R505 CORE,BEADS CORE,BEADS CORD AC BUSH CORD CONNECTOR FLAT CABLE AWM2468 FLAT CABEL AWM2468 CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER WIRE HOLDER WIRE HOLDER EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE MICRO FUSE REMOTE RECEIVER RELAY SPEAKER DEGAUSS ELEMENT TRANSMITTER RF UNIT CRT W/DY CRYSTAL
! !
! ! ! ! !
RESISTOR RC................... CARBON RESISTOR CAPACITORS CC................... CERAMIC CAPACITOR CE................... ALUMI ELECTROLYTIC CAPACITOR CP................... POLYESTER CAPACITOR CPP.................. POLYPROPYLENE CAPACITOR CPL.................. PLASTIC CAPACITOR CMP................... METAL POLYESTER CAPACITOR CMPL................ METAL PLASTIC CAPACITOR CMPP................ METAL POLYPROPYLENE CAPACITOR
J2-2
M3N4-24E A373606