Documente Academic
Documente Profesional
Documente Cultură
Washer
( ) Suggested Dimension
Unit:mm
5. Water Shutoff Valve Installation Please refer to the Installation manual of SW760B and SW761B for the
Warning
1. Please do not use any cleaning agent in the water tank, th prevent damage to product or building. Cleaning agents con Calcium Hypochlorite will damage the internal fittings of the
prevent damage to product or building. Cleaning agents con Calcium Hypochlorite will damage the internal fittings of the tank and this will cause tank leakage or damage to the buildi structure.
2. All the information in this manual are correct at the point printing, TOTO reserved the rights to make any changes to th product or content.
3. Please do not use cement on the product as cement will c bowl to crack and TOTO is not responsible for any of this dam
4. Please use the drain connector provided by TOTO. The pro performance might be affected if building is using anti curve piping. Apply anti-mold silicone on the surface where the bowl and the ground is in contact. Note: Do not use epoxy resin or sealing gel that will enlarge after drying, as our company will not be 5. Water supply pressure should be 0.05MPa ~ 0.75MPa.
Customer Note 1. Please clean your toilet bowl once a week with natural detergent if your local water quality is hard type to ensure the flushing outlet is clean. Use a long brush to clean the flushing outlet and drain outlet to prevent deposit from accumulating. Most cleaning agents will not damage the surface of the ceramic but please follow closely the instruction of the cleaning agent manufacturer. Please do not use acidic or corrosive agents. 2. Please do not dispose items such as newspaper, diapers, sanitary napkin that will clog the bowl. 3. Ceramic bowl is fragile product, please do not exert strong force on the ceramic to prevent it from damage and leakage. 4. Please do not use or store the product in an environment under 0C. 5. During first use, open the water shutoff valve slowly and at the same time conduct checks that there is no water leakage from the connection between the connecting pipe and the tank inlet and the water shutoff valve. 6. If the water level in the tank is not at the standard water line, this will affect the flushing performance. 7. Apply anti-mold silicone on the surface where the bowl and the ground is in contact. Note: Do not use epoxy resin or sealing gel. 8. If the water pressure is too high, please adjust the water shutoff valve to close accordingly to prevent the water shutoff valve's flexible hose from coming off. 9. Please do not use cleaning agents such as stain remover, very acidic or alkaline cleaner and nylon brush to clean the water shutoff valve and flexible hose.
Note:
1. Confirm the location of the water shutoff valve according to the dimension in diagram. 2. For CW761B and SW760B, please ensure the bowl and tank have been completely coupled before mounting to the locatio unable to install. 3. For CW761B and SW761B, please refer to the installation manual in SW761B packing for the tank installation and water s 4. Installation of Drain Connector and Mounting Bolt 1. Installation Location Screw Installed 2. Check Dimension
nd clean the surface. If installing a new toilet bowl, to prevent the drain hole from choking with rubbish. Drain Connector Mounting Bolt Item Mounting Quantity Drawing 3. Drain Connector Installation Center Line 4. Mark the outline of bowl and center
Screw
Decorative Cap Manual Warranty Seal (Not Included) Leave 10mm of Pipe from floor (suggested)
Mounting Hole
Outline of Bowl Position the bowl according to the marking of outline and centerline of the bowl and mounting. 6. Fitment of the Bowl
Install the drain connector according to diagram 3. Water Shutoff Valve 5. Location of Mounting attachment and Installation
Outline of Bowl
1. Connect the drain hole with the drain connector and ins mounting attachment. 2. Adjust the bowl into specific location and fit the screws.
ease do not use any cleaning agent in the water tank, this is to ent damage to product or building. Cleaning agents containing um Hypochlorite will damage the internal fittings of the water
ent damage to product or building. Cleaning agents containing um Hypochlorite will damage the internal fittings of the water and this will cause tank leakage or damage to the building
the information in this manual are correct at the point of ing, TOTO reserved the rights to make any changes to the
ease do not use cement on the product as cement will cause the to crack and TOTO is not responsible for any of this damage.
ease use the drain connector provided by TOTO. The product ormance might be affected if building is using anti-backflow
No need.
n SW761B packing for the tank installation and water shut off valve.
Finished Wall
Drain Hole
Center Line
Mounting Hole
Position the bowl according to the marking of outline and centerline of the bowl and mounting. Fitment of the Bowl
onnect the drain hole with the drain connector and install the
Adjust the bowl into specific location and fit the screws.
Please hand the installation manual to customer. Please install the product according to the manual for proper operation 1. Installation Parts Push Button Description 2. Packing List
Diagram
Flush Valve
Installation
Note: please use the actual product as standard, as it might varies fro 2-1. Flush Valve Installation 2-2. Adjustment of Float
Level Arrow Flush Valve Tank base Flush Valve Packing Lock Nut
Fit the Fill valve onto outlet valve attach point. Note: Ensure no contact between the fill valve float and the ceramic wall.
Fit the flush valve packing under the Flush valve and tighten the flush valve through the bottom of the tank with the lock nut. Note: 1. Please do not over tighten the nut as it might be damage. 2. Please position the overflow tube toward the front of tank
Ceramic
According to the diagram, insert the flush valve main unit into the groove of the flush valve base unit and turn clockwise 1/8 of a turn to complete the flush valve assembly.
Fit the flush button assembly, half the left, onto the tank lid and tighten it with the lock n rod for Yellow button and Blue rod for Blue button
Note: Adjust the water line by turning the float rod. Higher float means more fl lower float means less flushing volume. The water line cannot be higher than th
After Installation Test Mounting Bolt Tank Base Tank Fitment Defect Installed on Bowl
Water line is too low or too
Please flush the toilet 2 - 3 times to ensure the system is working no 4. Troubleshooting
1. Check whether is the water inlet open. 2. Check whether is the float of the fill valve
Firstly, fix the bolts onto the bowl as shown, next fix the gasket onto the flush valve opening and secure the tank and bowl with the mounting bolts. 5. Water Shutoff Valve Installation: (Not Included)
1. Please install the water shutoff valve according to the dimension and location in the manual. Actual water shutoff valve may vary from the manual. 2. Please ensure the flexible hose is properly connected to the fill valve opening with no leakage. Please do not use a flexible hose before the connection inlet of the water shutoff valve. Please close the water shutoff valve if not in use over a long period. Note: 1. Please clean any debris inside the water shutoff valve before installation. 2. Please maintain the original bend of the flexible hose. If the bend of the flexible hose is smaller than R60, over bending, twisting, stretching might damage the flexible hose and cause leakage. 3. If the water pressure is too high, please adjust the water shutoff valve to close accordingly to prevent the water shutoff valve's flexible hose from coming off. 4. Please install the water shutoff valve according to the diagram, TOTO is not responsible for any damage if a different installation method or parts are used by customer.
1. Check the nut of water inlet is tighten. 2. Reinstall the flush valve according to the st 3. Is the push button rod too long, that cause to be open. 1. Check whether is the flapper not to be fully open.
Customer Note:
1. Please clean your toilet bowl once a week with natural detergent if your local water ensure the flushing outlet is clean. Use a long brush to clean the flushing outlet and drain outlet to prevent deposit from a Most cleaning agents will not damage the surface of the ceramic but please follow clos cleaning agent manufacturer. Please do not use acidic or corrosive agents. 2. Please do not dispose items such as newspaper, diapers, sanitary napkin that will clo 3. Ceramic bowl is fragile product, please do not exert strong force on the ceramic to p and leakage. 4. Please do not use or store the product in an environment under 0 5. During first use, open the water shutoff valve slowly and at the same time conduct c water leakage from the connection between the connecting pipe and the tank inlet and 6. If the water level in the tank is not at the standard water line, this will affect the flush 7. Apply anti-mold silicone on the surface where the bowl and the ground is in contact. Note: Do not use epoxy resin or sealing gel. 8. If the water pressure is too high, please adjust the water shutoff valve to close accor water shutoff valve's flexible hose from coming off. 9. Please do not use cleaning agents such as stain remover, very acidic or alkaline clean clean the water shutoff valve and flexible hose.
- Please refer to the installation manual for water shutoff valve if customer choose to couple with a washlet.
1. Please do not use any cleaning agent in the water tank, this is to prevent d or building. Cleaning agents containing Calcium Hypochlorite will damage the of the water tank and this will cause tank leakage or damage to the building 2. All the information in this manual are correct at the point of printing, TOTO rights to make any changes to the product or content. 3. Please do not use cement on the product as cement will cause the bowl to not responsible for any of this damage. 4. Please use the drain connector provided by TOTO. The product performan affected if building is using anti-backflow curve piping. 5. Water supply pressure should be 0.05MPa ~ 0.75MPa.
No need.
Packing List Description Ceramic Quantity 1 set Remarks Water Tank and Lid
Fill Valve
1 piece
Installed
Flush Valve
1 piece
Installed
use the actual product as standard, as it might varies from diagram. 2. Adjustment of Float
h valve and tighten the flush valve through Please adjust the float with the arrow pointing at level 8. as it might be damage.
the flush button assembly, half-flush on the right and full-flush on the left, onto the tank lid and tighten it with the lock nut. Note: White rod for Yellow button and Blue rod for Blue button
turning the float rod. Higher float means more flushing volume, ns less flushing volume. The water line cannot be higher than the overflow
Solution
Please refer to Step 6 for adjustment of water line 1. Check whether is the water inlet open. 2. Check whether is the float of the fill valve pressed against 1. Check the nut of water inlet is tighten. 2. Reinstall the flush valve according to the steps. 3. Is the push button rod too long, that cause the flush flapper to be open. 1. Check whether is the push rod too short which cause the flush flapper not to be fully open.
your toilet bowl once a week with natural detergent if your local water quality is hard type to
h to clean the flushing outlet and drain outlet to prevent deposit from accumulating. gents will not damage the surface of the ceramic but please follow closely the instruction of the
dispose items such as newspaper, diapers, sanitary napkin that will clog the bowl. is fragile product, please do not exert strong force on the ceramic to prevent it from damage
use or store the product in an environment under 0C. se, open the water shutoff valve slowly and at the same time conduct checks that there is no om the connection between the connecting pipe and the tank inlet and the water shutoff valve. evel in the tank is not at the standard water line, this will affect the flushing performance. old silicone on the surface where the bowl and the ground is in contact.
ressure is too high, please adjust the water shutoff valve to close accordingly to prevent the alve's flexible hose from coming off. use cleaning agents such as stain remover, very acidic or alkaline cleaner and nylon brush to shutoff valve and flexible hose.
ot use any cleaning agent in the water tank, this is to prevent damage to product eaning agents containing Calcium Hypochlorite will damage the internal fittings ank and this will cause tank leakage or damage to the building structure. mation in this manual are correct at the point of printing, TOTO reserved the e any changes to the product or content. ot use cement on the product as cement will cause the bowl to crack and TOTO is e for any of this damage. he drain connector provided by TOTO. The product performance might be backflow curve piping. ly pressure should be 0.05MPa ~ 0.75MPa.