Documente Academic
Documente Profesional
Documente Cultură
02SEP2008
Subject: Implementation of revised standard IS 513:2008 for Cold Reduced Low Carbon Steel sheet and Strip and Revised STI Doc: STI/513/7 Nov. 2008. IS 513:1994 has been revised as IS 513:2008. Following modifications have been made in this revision : a) ISO designations have been adopted.. b) Table 1 and table 3 have been modified. c) New Grade CR5 Extra deep drawing (Stabilized interstitial free) has been added. d) Correlation of Old designation with new designation has been given for information( Annex A). e) A new clause on references has been incorporated. f) Amendments No. 1 and 2 have been incorporated. g) IS 8910:1978 has been adopted for general technical delivery requirements. h) Clause on retest has been modified. j) Values for plastic anisotropy (r) and strain hardening exponent(n) have been incorporated. k) Applicable period of mechanical and physical properties has been included. l) Requirements of dimensional and shape tolerances have been separated from the standard and adopted IS/ISO 16162:2005 Continuously cold rolled steel sheet products- Dimensional and shape tolerances and m) A clause for alternate test method specified in relevant ISO/IEC standard has been added. The draft revised STI was circulated vide CMD Note of even number dated 9 July 2008 for seeking comments of ROs/BOs. However comments were received from IOJ only. Accordingly, STI has been revised as Doc: STI/513/7 Nov. 2008 ( copy of STI available on BIS Intranet). In order to implement, revised standard and Scheme of Testing and Inspection following procedure shall be adopted: For existing licensees: 1. Based on actual situation in respect of the operating licences applicability of the changes may be examined and verified if required. 2. Endorsement in the licence as per revised standard shall be made after obtaining the Acceptance of revised STI. 3. Action shall be taken as per OMPC 2004, if the licensee fails to submit the acceptance of STI in stipulated time.
For Applicants: 1. During the period upto 30th October 2008 applications may be recorded and processed for GOL as per IS 513:1994. An undertaking may be obtained from the firm that the action required to switchover to IS 513:2008 shall be completed before 1st November 2008.
REVISED STANDARD IS 513:2008 AND REVISED STI Doc: STI/513/7 Nov. 2008 WILL BE IMPLEMENTED w.e.f 1st November 2008. All ROs/BOs are requested to take necessary action. STI may be downloaded from BIS Intranet.
DDGM sd/--04.09.2008
In addition efforts should be made to gradually introduce the Quality Management System in accordance with IS/ISO 9001.
3.1 4 STANDARD MARK - The Standard Mark, as given in Column (1) of the first schedule of the licence is specified for cold rolled low carbon steel sheets and strips specified in IS 513:2008. The grade designation shall be mentioned in the Test Certificate (See Annexure 1). 4.1 TEST CERTIFICATE For each consignment of BIS Certified material conforming to IS 513:2008 there shall be a test certificate which shall contain the Standard Mark, the cast number, coil number, the quality designation and the corresponding test results (as given in Annexure I). 4.2 MARKING The following shall be legibly marked on the top of each bundle or package of sheets and strips or shown on a tag attached to each coil : a) b) c) d) e) f) g) Manufacturers name or trade mark, Quality designation (designation, name ,temper and surface finish) Product dimensions, Cast or identification mark by which the sheet or strip may be traced to the cast or casts from which they were made, Mass/Net weight and Date of dispatch. Licence No. (CM/L.)
Page 1 of 8
Page 2 of 8
5.2.7.3 The angle of bend and internal diameter of the bend for the different grades of material shall be as given in Table 6 & 7 (Ref. cl. 7.4.2) of IS 513:2008. The axis of bend shall be in the direction of rolling. 5.2.8 CUPPING TEST - Cupping test shall be carried out for sheets ,strips and coils of CR 2, CR 3, and CR 4 grades having thickness from 0.5 mm to 2.00 mm. 5.2.8.1 Cupping test shall be carried out in accordance with IS 10175(Part.1). The minimum erichson cupping test values shall be as given in fig. 1 of IS 513:2008. The shape of the cup fracture may be as mutually agreed between the purchaser and supplier. 5.2.9 HARDNESS TEST - In case material is supplied after heat treatment, hardness test shall be conducted for each heat treated batch or a lot of 50 tonnes, whichever is less. In case of coil, one sample from each coil shall be taken. 5.2.9.1 Hardness test shall be carried out in accordance with IS 1586 and IS:1501 as applicable. A visible deformation on the back side of the specimen is permitted. the values determines in this way shall be identified by using symbols HRB and HR30T, (Ref. Table 4 &5 of IS 513:2008) so as to differentiate these from the hardness values determined on thicker products (which are not allowed to exhibit a visible deformation on the back side of the specimen. 5.2.10 Plastic Srain Ratio, r -The plastic strain ratio is an index of draw ability (r), shall be applicable only to thickness between 0.5 to2.0 mm. For thicknesses more than 2.0 mm, the r value is reduced by 0.2. Page 3 of 8
Sr.No. 1. a)
b) 2.
3. 4 5
6.
7 8.
Page 5 of 8
ANNEXURE I (Para 4.1 of the Scheme of Testing and Inspection) XYZ IRON AND STEEL COMPANY (Registered office Address and works address) TEST CERTIFICATE FOR COLD REDUCED CARBON STEEL SHEET AND STRIP
STANDARD MARK
It is certified that the material described below fully conforms to IS 513:2008 Chemical composition and Mechanical properties of the product, as tested in accordance with the Scheme of Testing and Inspection contained in the BIS Certification Marks Licence No.CM/L_____________________ are as indicated below against each order No. etc. (PLEASE REFER TO IS 513:2008 FOR DETAILS OF SPECIFICATION REQUIREMENTS)
TEST RESULTS Ord er No. & Dat e design ation, name, temper and surface finish Ca st No . Qua ntity tonn es CHEMICAL ANALYSIS C Mn S P Cu Al ** PHYSICAL PROPERTIES Yiel Tensi Elo Be d nd le nStre Stren gati Test ss gth on Mp MPa+ a % % % N Si Non agei ng Cha r. Plas tic strai n Rati o, r Tensile strain hardeni ng compon ent, n Rema rks
Cuppi ng Value
% %
% % %
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
The material supplied conforms to the standard rolling and weight tolerances. ** For Copper bearing quality REMARK SHIPPING ADVICE No. WAGON NOS. (It is suggested that size A-4 paper (210 x 297 mm) be used for this Test Certificate) Page 6 of 8 + If specified by the purchaser.
PERFORMA - 1
PROFORMA FOR OBTAINING PRODUCTION DETAILS Period covered Name of Licensee CM/L No. Name of Articles (s) Grade/Type/Size/Variety/Class/Rating IS No.
1.1 2.0
Brand/Trade/Name(s) of BIS Certification Marked Products Total production of the articles(s) licensed for certification marking Total production of the article(s) conforming to Indian Standard Production covered with BIS Certification Mark and its value a) b) Quantity Value (Rs.)
2.1
3.0
3.1 3.2 a) b) c)
Brand Name used on production covered under BIS Certification Mark Calculation of marking fee on unit-rate basis; Marking Fee per unit Unit Quantity covered with BIS Certification Mark Marking fee rounded off in whole rupees as obtained by applying unit rates given in (a) on quantity given in (b)
Note : Incase a clause is not applicable, suitable remarks may be given against it. Page 7 of 8
4.0
Quantity not covered with BIS Certification Mark. If any, and the reasons for such non-coverage Brand Name under with non certified goods were sold Quantity Exported with BIS Standard Mark and its value Brand Name under which BIS Certified goods are exported Authentication by Chartered Accountant or by the manufacturer by giving an affidavit/undertaking
Page 8 of 8