Documente Academic
Documente Profesional
Documente Cultură
Remedy: To remove this problem, the soldering rivet Z 601 has to be soldered again
Modifications reserved !
Schneider AG
Service - Info
Unit : Chassis TV 9.xx No.: 246
Concern: Failure of the horizontal deflection Q 304 Remedy: Following parts have to be componented, controled or removed: 1.) A cap cable high voltage - transformer diode split has to be componented 2.) The software IC 902 has to be changed through the latest version 3.) A circuit connection has to be soldered in from Pin 1 / IC 701 to ground (look the sketch) 4.) A circuit connection has to be soldered in from C 704 to ground (look the sketch) 5.) The chip Z 703 has to be removed 6.) A circuit connection has to be componented like the sketch (six centimetre long) 7.) A circuit connection has to be soldered in from IC 701 / Pin 24 to Pin 25 8.) A circuit connection has to be soldered in from IC 701 / Pin 55 to Pin 56 9.) Two Diode BZT55C 5,6V have to be soldered in from IC 701 / Pin 3 and 4 to ground (anode to ground)
Attention: The modifications was already integrated in production, therefore a modification isnt necessary in all cases. The changing of IC 902 is only necessary, if the Diode BZT55C wasnt componented in pro duction. Part number cap cable high voltage: 0105922 Part number Diode BZT55C: 0100789 Part number IC 902: The IC 902 has to be ordered by means of the TV part number. Modifications reserved !
Schneider AG
Concern:
Remedy:
The high frequency whistling may be caused by coming into contact of the fitting clip / diode D 305 with the capacitor in position C 314. For remedy the capacitor in position C 314 has to be replaced by a smaller version.
Part number capacitor for chassis TV 9.1: Part number capacitor for chassis TV 9.3:
0100865 0109085
Modifications reserved !
date: 14.09.00
Service information !
Concern: Rectifier / Chassis TV 9.XX ( pos. D 102 )
for checkback:: TV-Hotline: 0049 8245-51 108 Spare part department: 0049 8245-51 71
In case of service the rectifier in position D 102 has to be replaced by the replacement version alike the below declared sketches.
Modification reserved!
date: 18.09.00
Service information !
Unit type : Concern: Chassis TV 9.xx Multipage Blocking control function by receiving low level or disturbed antenna signal
for checkback:: TV-Hotline: 0049 8245-51 108 Spare part department: 0049 8245-51 71
Concern : Blocking control function by receiving low level or disturbed antenna signal.
Remedy : In case of service the IC in position IC 902 has to be replaced by the latest version.
Attention : Due to several chassis version the IC in position IC 902 has to be ordered depending on the set identification number.
Modification reserved!
Schneider AG
Remedy: The chip-capacitors C 403 and C 404 ( 100 nF/25V ) has to be removed and replaced by a 220 nF / 50V version.
0100057
Modifications reserved !
Schneider AG
Remedy: The chip-resistor in position CR 410 has to be removed, and the chip-capacitor in position CC701 has to be altered in a 1nF version.
0100034
Attention: The modification concerning the chip-capacitors was already integrated in production, therefore a modification may be not necessary in all cases.
Modifications reserved !
Schneider AG
Remedy: One 10k chip resistor has to be componented additional between pin 12 / IC 701 and the chip capacitor C 704 ( use the printed line to Pin 5 and Pin 1 from IC 701).
C 704
PIN 12
0038967
Schneider AG
Chassis TV 9 No.:236
Attention: The modification 1, 2 and 5 are already integrated up to board number 0109040.
Modifications reserved !
Schneider AG
Remedy: The horizontal RGB position can be altered in the servicemode / alignment parameter Horizontal Pos. RGB .
Service-Mode: Simultaneously press and then release the red and blue button on the remote control. Simultaneously press and then release within 5 seconds the buttons program + and volume - at the local control panel. The main service menu appears on the screen : 4 : 3 Service Mode TV 9 OK . . save Version TV . . leave menu XX
Select the parameter Horizontal Pos. RGB with the button 5/6( program + / - ) on the remote control. The RGB menu appears on the screen: 4 : 3 Horizontal OK . . save Pos. RGB - 10 TV . . leave menu
Alter with the buttons3/4( volume + / - ) the on the remote control the horizontal position best possible. Press the button OK on the remote control to store it. Press the button TV to leave the service mode.
Modifications reserved !
Schneider AG DUAL GmbH Silvastrae 1 D-86842 TRKHEIM Date: 17.07.00 Service-Info Concern : TV 9 NVM values depending on the set type Info 241
The chassis TV 9 exists in different versions and was used with several picture tubes. After an EEPROM swap or after a new initialisation the geometry, video and program parameter will be deleted and replaced by standard values. Therefore these parameter have to be set again. But attention, at first the set has to be set into the delivery status ( info menu / parameter reset ) alike the instruction manual. After that, the below declared NVM addresses have to be observed and if necessary to be altered according the below declared table:
NVM-Values for Chassis TV9.1 B/G + TV9.1 B/G-PIP Picture tube:
A59EMZ07X... + A59TMZ43X... A59EMZ05X... A59ECF50X... A66EAK552X.. + A66EAK071X... A66EHJ43X... A63EQQ50X... A66EMZ43X... A66ECF50X..
0059
0F 31 0E 0F -
005A
00 01 00 -
005E
31 2D 31 -
0062
17 17 16 16 16 16 17 -
0E30
FE FE 2C 2C C8 FE FE 2C
0E31
00 00 01 01 00 00 00 01
0E40
BC CA B4 B4 D5 D1 C4 C2
0E44
2D 2D 64 90 5F 64 47 55
0066
0F 0F 0F 0F 0F 0F 0F -
0080
69 69 69 69 69 69 69 -
0E50
2C 30 30 2B 30 2C 2C 2B
0E80
01 01 01 01 01 01 01 01
0082
A59EMZ07X... + A59TMZ43X... A59EMZ05X... A59ECF50X... A66EAK552X.. + A66EAK071X... A66EHJ43X... A63EQQ50X... A66EMZ43X... A66ECF50X.. 00 00 00 00 00 00 00 00
0068
B9 B0 AA A1 B9 B2
0069
01 01 01 01 01 01
006A
C5 BB B0 B1 C5 BE
006B
01 01 01 01 01 01
0078
6D 6D 70 6D 6D 6D
0200
1D 1D 1D 1D 1D 1B 1D 1D
0201
18 18 18 18 18 16 18 18
0202
15 15 15 15 15 15 15 15
0049
00 00 00 00 00 00 00 00
0E1D
04 04 04 04 04 04 04 04
1/4
0082
00
0068
B9
0069
01
006A
C5
006B
01
0078
6D
0200
1D
0201
18
0202
15
0049
00
0E1D
04
0059
0F
005A
00
005E
31
0062
17
0E30
FE
0E31
00
0E40
BC
0E44
2D
0066
0F
0080
69
0E20
01
0E50
2C
0C03*
A59EMZ07X... + A59TMZ43X... A59EMZ05X... A59ECF50X... A66EAK552X.. + A66EAK071X... A66EHJ43X... A63EQQ50X... A66EMZ43X... A66ECF50X.. 2A 2A 2A 2A 2A 2A 2A 2A
0068
B9
0069
01
006A
C5
006B
01
0078
6D
0200
1D
0201
18
0202
15
0049
00
0E1D
04
B0
01
BB
01
6D
1D 1D 1D
18 18 18
15 15 15
00 00
04 04 04
AA A1 B9 B2
01 01 01 01
B0 B1 C5 BE
01 01 01 01
70 6D 6D 6D
1D 1B 1D 1D
18 16 18 18
15 15 15 15
00 00 00 00
04 04 04 04
0049 00 00 0D03 01 01
0068 AA B2 0E00 11 11
0069 01 01 0E20 01 01
006A B0 BE 0E30 C8 2C
006B 01 01 0E31 00 01
0078 70 6D 0E40 D5 C2
0200 1D 1D 0E44 7F 5F
0201 18 18 0E50 2B 2B
0202 15 15
0300 11 11
050F 01 01
0D19 01 01
0D1A 00 00
0D1C 00 00
0D02 03 03
0066
0F 0F 0F
0080
69 69 69
0E20
01 01 01
0E50
2F 2F 2A
0059
0E -
0062
16 16 16
0E30
C8 2C C8
0E31
00 01 00
0E40
D5 B4 D7
0E44
5F 64 54
0E1E
01 01 01
00AB
CC
2/4
008A
3D 0E7E 5E
0D19
01 0E7F 01
0E24
C3 0E84 AA
0E26
3D 0E86 5A
0E28
89 0E88 88
0E50
2C 0E8A B0
0E60
26 0E8C 50
0E64
D3 0E8E 00
0E6C
56 0E8F 04
0E70
99 0E90 00
0E78
B0 0E91 04
0E79
00 0E22 01
0E7A
B0 0E30 13
0E7B
00 0E31 01
0E7C
5E 0E48 30
0E7D
01 0E4A 17
0049
00
0066
0F
0080
69
005C
3C
00AB
90
0200
1A
0201
1A
0202
17
0203
17
0E30
B0
0E31
00
0E40
DF
0E44
04
0E50
31
0E80
01
0049
00 00 00 00
0059
0F
0062
17
0068
98 A0 A0 A0
0069
01 01 01 01
006A
A7 AC AC AC
006B
01 01 01 01
00C2
1A 1A 1A 1A
00C3
1D 1D 1D 1D
0200
1D 1D 1D 1D
0201
18 18 18 18
0202
15 15 15 15
031C
03 03 03 03
0E60
C8 2C FE FE
0E61
00 01 00 00
0E70
A66 EHJ 43X... A66 EAK 71X... A66 EMZ 43X... A66 ECF 50X... 33 54 4F 4F
0E74
60 19 51 51
0E78
10 10 10 10
0E7A
33 33 33 33
0E80
29 2B 2B 2B
0EBE
04 04 04 04
0EB0
01 01 01 01
0ED4
64 64 64 64
0EE1
FF FF FF FF
0EE2
02 02 02 02
0049
00 00 00 00
0059
0F
0062
17
0068
98 A0 A0 A0
0069
01 01 01 01
006A
A7 AC AC AC
006B
01 01 01 01
00C2
1A 1A 1A 1A
00C3
1D 1D 1D 1D
0200
1D 1D 1D 1D
0201
18 18 18 18
0202
15 15 15 15
031C
03 03 03 03
0E60
C8 2C FE FE
0E61
00 01 00 00
0E70
A66 EHJ 43X... A66 EAK 71X... A66 EMZ 43X... A66 ECF 50X... 33 54 4F 4F
0E74
60 19 51 51
0E78
10 10 10 10
0E7A
33 33 33 33
0E80
29 2B 2B 2B
0EBE
04 04 04 04
0ED4
64 64 64 64
04B7
01 01 01 01
04BA
02 02 02 02
04CE
03 03 03 03
OE50
01 01 01 01
0EE1
FF FF FF FF
0EE2
02 02 02 02
3/4
0049
00 00
0059
0E 0F
0062
17
0066
0F 0F
0068
CD E5
0069
01 01
006A
DB F0
006B
01 01
00A6
01 01
00C3
17 17
0200
1D 1D
0201
18 18
0202
15 15
031C
03 03
0E4E
01 01
0E60
A66 EHJ 43X... A66 EMZ 43X... C8 FE
0E70
D5 -
0E74
5F 47
0E80
2C
For information: If the sound disappear after the IC swap ( IC 904 ) the new initialisation of the channel positions has to be taken according service manual TV 9. Additonal the NVM address 0ED2 has to be set according the following table depending on the tuner type:
Set the NVM-address: 0ED2 To NVM-Data : 00 = Tuner 5002 PH5 or 01 = Tuner 6002 PH5
Service-Mode:
Simultaneously press and then release the red ( picture menu ) and blue ( videotext ) button on the remote control. Simultaneously press and then release within 5 seconds the buttons program - and volume + at the local control panel. The NVM menu appears on the screen. Select with the buttons n / o on the remote control the parameter NVM addr. The NVM menu appears on the screen. The settings can be selected with the red ( picture menu ) button on the remote control and changed with buttons volume + and volume -. Each changing of an address has to be stored separately with the button OK on the remote control. After the changing of the addresses leave the service mode with the button TV . To activate the modification switch off the set with the main power switch and start it again.
Modifications reserved !
4/4
Schneider AG
- The chip resistor in position CR 745 ( 100 ) has to be removed and replaced by a 0 version - Between emitter and basis from transistor a 0 chip resistor has to be componented additional ( like illustration )
0100060
Modification reserved !
Schneider AG
Service - Info Unit type Concern part no. KD0002K : TV 9. : Software 0101511 No.: 251
Remedy: To avoid the failure Teletext or digital pixel on the screen the integrated software ( IC 902 ) has to be the version 2.AA or higher .
Modifications reserved !
Schneider AG
Service info
Unit type: Chassis TV 9.6 no.: 260
Concern: Remedy:
Lapsing of the 500 pages videotext memory. To eliminate this fault the below declared NVM address has to be altered in the service-mode.
Service-Mode: Simultaneously press and then release the red ( picture menu ) and blue ( videotext ) button on the remote control. Simultaneously press and then release within five seconds the buttons "program -" and "volume +" at the local control panel. The main service menu appears on the screen:
4 : 3 Service Mode TV 9 OK . . save Version TV . . leave menu XX
Call up with the buttons program + / - on the remote control the parameter NVM addr.. The NVM menu appears on the screen:
4 : 3 NVM OK . . save addr. 0000 data FF TV . . leave menu
The several positions of the NVM address and NVM data can be selected with the red ( picture menu ) button and changed with the buttons volume + / - on the remote control . Each changing of an address has to be stored separately with the button OK on the remote control. Select the following NVM address and set it according the following table:
Set the NVM address 0EE2 to NVM data 02
After the changing of the address leave the service-mode with the button TV on the remote control. To activate the modification switch off the TV and start it again. Attention: The changing of other addresses can effect further failure.
Modifications reserved !
Schneider AG
Concern:
Attention:
The chassis TV 9.4 was produced in combination with several picture tubes. Therefore the operating voltage has to be set according following information :
Chassis TV 9.4 in combination with picture tube A 51 JSY 63X13 = 136V (0,5V) Chassis TV 9.4 in combination with picture tube A 51 EER 131X78 = 130V (0,5V)
Modification reserved !
No.: 0105942
date: 05.10.00
Service information !
Chassis TV 9.3 in connection with picture tube type W 66 ECK 001X13 Unsynchronizing PIP picture ( PIP-module version 3 )
Concern:
for checkback:: TV-Hotline: 0049 8245-51 108 Spare part department: 0049 8245-51 71
PIP-module version 3: The Chip resistor in position R 1204 has to be removed and replaced by a 270 Ohm / 150V chip resistor. The chip diode BZT55C in position D1202 has to be componented in addition. Spare part number: Chip resistor 270 Ohm Chip diode BZT55C 0100090 0100683
Modification reserved!
Schneider AG
Service info Unit type: KD0002K : Chassis TV 9 / TV 9.1 / TV 9.2 / TV 9.3 no.: 224
Concern: Neutralization of the child lock. Remedy: The child lock can be neutralized as follows: Switch to the service mode and inspect, if the parameter KISI ruecksetzen is displayed on the screen. Is this parameter available, proceed like point , otherwise like point . Service-Mode: Simultaneously press and then release the red and blue button on the transmitter. Simultaneously press within five seconds the buttons "Programme -" and "Volume +" at the local control panel. The main service menu is displayed on the screen:
4 : 3 Service Mode TV 9 OK . . save Version TV . . leave menu XX
Call up with the keys / , the tuning parameter NVM addr. . The nvm menu is displayed on the screen:
4 : 3 NVM OK . . save addr. 0000 data FF TV . . leave menu
The several positions of the nvm address and nvm data can be selected with the red button and changed with the buttons volume +/ -. Each address changing has to be stored separately with the key OK. Select following nvm addresses and adjust them to following values:
After the adress changing, leave service mode with the key TV. To save the adress changing in the eeprom, switch the television OFF and soon after ON. Attention: The changing of other addresses can effect secondary failure. Call up the tuning parameter Kisi rcksetzen and set the value from 0 to 1. The changing has to be stored with the key OK. Leave service mode with the key TV.
Modifications reserved !