Documente Academic
Documente Profesional
Documente Cultură
Precision Timer
Features
Mono multi vibrator can be constructed with one resistor and one capacitor. Astable multi vibrator can be constructed with two resistors and one capacitor. Delay time can be established widely from several seconds to several hours. Pulse Duty can be controlled. The maximum value of both sink current and source current is 200mA. Direct connection of output to TTL is possible. Temperature/delay time ratio is 50 ppm/C (typ). Output is normally in the on and off states.
Ordering Information
Application Industrial use Type No. HA17555PS HA17555FP Commercial use HA17555 HA17555F Package DP-8 FP-8D DP-8 FP-8D
HA17555 Series
Applications
Delay Time Generator (Mono Multi Vibrator) Pulse Generator (Astable Multi Vibrator) Pulse Width Modulator Pulse Location Modulator Miss Pulse Detector
Pin Arrangement
1 2 3 4
8 7 6 5
(Top View)
Pin Description
Pin No. 1 2 3 4 5 6 7 8 Function Ground pin Trigger pin Output pin Reset pin Control voltage pin Threshold pin Discharge pin VCC pin
HA17555 Series
Circuit Schematic
Control Voltage VCC R1 Q5 R2 Q6 Q7 R3 Q8 Q9 R7 R4 Q19 R13 Q23 Threshold Q1 Q2 Q3 Q18 R8 R11 Q11 Q12 Trigger R5 Q10 Q13 Q16 Q17 R16 R15 Q14 Q4 Q20 R14 Q24 Discharge Output R12 Q21 Q22
R6 R9
Q15 GND
Reset
Q25
Block Diagram
VCC
Threshold Control
Trigger
S CLR
Output Discharge
Reset
HA17555 Series
Absolute Maximum Ratings (Ta = 25C)
Item Supply voltage Discharge current Output source current Output sink current Power dissipation*
1
Unit V mA mA mA mW C C
1. For the HA17555/PS, This value applies up to Ta = 50C; at temperatures above this, 8.3mW/C derating should be applied. For the HA17555F/FP, This value applies up to Ta = 25C; at temperatures above this, 3.85mW/C derating should be applied. See notes on SOP Package Usage in Reliability section.
HA17555 Series
Maximum Power Dissipation PTmax (W) 0.7 0.6 0.5 3.85 mW/C 0.4 0.3 0.2 0.1 b. 0.385 W a. 0.6 W 8.3 mW/C a. HA17555PS b. HA17555FP
40 20 0 20 40 60 70 80 100 120 Ambient Temperature Ta (C) Maximum Power Dissipation PTmax (W) a. HA17555 b. HA17555F a. 0.6 W 8.3 mW/C 3.85 mW/C 0.4 0.3 0.2 0.1 b. 0.385 W
HA17555 Series
Electrical Characteristics (VCC = 5 to 15 V, Ta = 25C)
Item Supply voltage* Supply current
1
Typ 3.0 10 1.0 50 0.01 2/3 5.0 1.67 0.5 0.5 0.1 0.1 10 3.33 0.1 0.4 2.0 2.5 0.25 12.5
Max 16.0 6.0 15 1.0 0.25 11 4.0 0.25 0.75 2.5 0.35
Timing error* (Inherent error) Timing error*2 (Ta dependency) Timing error*2 (Voltage dependency) Threshold voltage Trigger voltage
Et Et Et Vth VT VT
Ta = 20 to + 75C VCC = 5 to 15 V
VCC = 15 V VCC = 5 V
Trigger current Reset voltage Reset current Threshold current Control voltage
9 2.6
VCC = 15 V VCC = 5 V VCC = 15 V, Isink = 10 mA VCC = 15 V, Isink = 50 mA VCC = 15 V, Isink = 100 mA VCC = 15 V, Isink = 200 mA VCC = 5 V, Isink = 5 mA VCC = 15 V, Isource = 200 mA VCC = 15 V, Isource = 100 mA VCC = 5 V, Isource = 100 mA No loading No loading
Output voltage
VOL
Output voltage
VOH
12.75 13.3 2.75 Output rise time Output fall time Oscillation pulse width* Notes: 1. 2. 3. 4.
4
tr tf tw
10.0
When output is low (When it is high, ICC is lower by 1 mA typically.) RA, RB = 1 k to 100 k, C = 0.1 F, V CC = 5 V or 15 V. (RA + RB) at VCC = 15 V is determined by the value of Ith. It is 20 M Max. Output pulse width at mono multi circuit. Output high level pulse width at astable circuit.
HA17555 Series
Characteristic Curves
Quiescent Current vs. Supply Voltage 12.0 Vout : Low Level 10.0
Quiescent Current ICC (mA) Supply Voltage VCC Output Voltage VOH (V)
Supply Voltage (VCC) Output Voltage (VOH) vs. Source Current 2.0 Ta = 20C 1.6 25C 1.2 75C
4.0
0.8
2.0
0.4
0 5.0
0 1 3 10 30 Source Current Isource (mA) Output Voltage (VOL) vs. Sink Current (2) 10 VCC = 10 V
Output Voltage VOL (V)
15.0
100
VCC = 5 V
1,000
1,000
3 1.0 0.3 0.1 0.03 0.01 1 3 10 30 100 300 Sink Current Isink (mA) 1,000 Ta = 75C
20C 25C
HA17555 Series
Relative Delay Time vs. Ambient Temperature 1.015 1.010 Relative Delay Time 1.005 1.000 0.995 0.990 0.985 20 0 20 40 60 80 Ambient Temperature Ta (C) Minimum Trigger Pulse Width (ns) 200 Minimum Trigger Pulse Width vs. Low Level Trigger Voltage
150
100 Ta = 20C 50 25C 75C 0 0.1 0.2 0.3 0.4 Low Level Trigger Voltage (VCC)
Propagation Delay Time vs. Low Level Trigger Voltage 300 Propagation Delay Time (ns)
200
Ta = 20C
0.4
HA17555 Series
Package Dimensions
Unit: mm
9.6 10.6 Max 8 5
6.3 7.4 Max
1 0.89
4 1.3
2.54 Min 5.06 Max
1.27 Max
7.62
0.1 Min
0.25 0.05 0 15
Hitachi Code JEDEC EIAJ Mass (reference value)
+ 0.10
2.54 0.25
0.48 0.10
Unit: mm
4.85 5.25 Max 5 8
4.4
4
*0.22 0.05 0.20 0.04 2.03 Max
0.75 Max
1.05 0 8
0.10 0.10
0.15 0.12 M
*Dimension including the plating thickness Base material dimension Hitachi Code JEDEC EIAJ Mass (reference value) FP-8D Conforms 0.10 g
HA17555 Series
Cautions
1. Hitachi neither warrants nor grants licenses of any rights of Hitachis or any third partys patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third partys rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact Hitachis sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the Hitachi product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Hitachi. 7. Contact Hitachis sales office for any questions regarding this document or Hitachi semiconductor products.
Hitachi, Ltd.
Semiconductor & Integrated Circuits. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109
URL
: : : :
10