Documente Academic
Documente Profesional
Documente Cultură
VOLUME
DOWN UP
REMOTE SENSOR
CHANNEL
DOWN UP
POWER
SUFFIX B
5721-37CN030T (370KSB22(SYB)) 4993-052
SUFFIX C
5721-026TT37N (A34JFQ90X) 4993-110
SUFFIX D
5721-030ZT37N (A34JXV70X) 4993-124
DY501
2. From the menu screen, press the + or - button on the Remote Control to select the item to be adjusted. 3. Press the MENU button on the Remote Control to enter adjustment mode for the item selected, and the display shown below appears :
Example: 4. Use the + or - button on the Remote Control to adjust the data for the item selected. 5. When adjustment has been completed, press the SHIFT + ADJ. MODE buttons on the Remote Control simultaneously to return to the main menu.
-3-
VIDEO
-4-
TRANSISTORS Q101 DTC143ZS Q102 2SC945(P) Q173 2SC945(P) Q301 2SC945(P) Q302 2SA733(P) Q303 2SC945(P) Q351 DTC143ZS Q451 2SC1473A(R) Vertical Synchronizing Horizontal Synchronizing SD Signal Buffer SIF Signal Buffer Video Buffer Amplifier Video Out Service Mode Switching Red Color Driver Q452 2SC1473A(R) Q453 2SC1473A(R) Q551 2SC1473A(R) Q552 2SD 1 877 Q601 2SC945(P) Q801 2SC945(P) Q802 2SA950(0) Q803 2SC2120(0) Blue Color Driver Green Color Driver Horizontal Driver Horizontal Driver Power On/Off Relay Driver Audio Amplifier Audio Amplifier Audio Amplifier
PICTURE TUBE V451 37GDA86X CRT (SUFFIX A) V451 370KSB22(SYB) CRT (SUFFIX B) V451 V451 A34JFQ90X A34JXV70X CRT (SUFFIX C) CRT (SUFFIX D)
CHASSIS REMOVAL 1. 2. 3. 4. 5. 6. Remove 4 screws (183) from Cabinet Back (AB) and remove Cabinet Back from rear. Discharge anode lead at CRT chassis ground through a 10kohm resistor. Disconnect anode lead from CRT. Disconnect CRT Socket P.C. board (PCB-2) from CRT(V451). Disconnect 3 connectors (CN501 (DY501), CN601 (L601) and LCN801) from Main P.C. board (PCB-1). When replacing chassis, reverse the above procedure making certain that all leads are fastened in their original places.
CRT REMOVAL CAUTION: Wear shatterproof goggles and exercise proper handling precautions when working around high vacuum picture tubes. 1. Remove chassis per instructions under CHASSIS REMOVAL. 2. Remove Convergence Magnet Assembly (MG451) from neck of CRT. 3. Remove Deflection Yoke (DY501) from neck of CRT 4. Remove 3 wedges (158) from CRT 5. Remove Degaussing Coil (L601) from CRT 6. Remove braid wire (331) and spring (157) from CRT 7. Lay cabinet face down on some protective material. 8. Remove 4 CRT mounting screws (174). 9. Remove CRT from Cabinet Front (AA). 10. To install new CRT, reverse above procedure. 11. Perform purity and convergence adjustments.
-5-
FIG. 1
FIG. 2
-6-
SOUND IF ADJUSTMENT
1. Connect TV Test Pattern Generator (NTSC signal, 70dB u , channel 2) to EXT. Antenna Terminal (TE1) through TV Channel Signal Generator. (Standard modulation is 400Hz at 25kHz deviation for sound signal. Connect positive lead of DC Digital Voltmeter to TP7 and negative lead to TP9. Adjust T203 so that the DC Digital Voltmeter reading is 4.0V.
2. 3.
3.
Set the Contrast control to minimum position and Brightness control as far maximum as possible without causing the picture to bloom. 4. Apply green raster signal from Dot/Bar Generator to receiver. 5. Loosen the deflection yoke clamp screw and pull the deflection yoke toward the rear of the CRT. 6. Begin the following adjustment with the tabs on the round purity magnet rings set together. Slowly separate the two tabs while at the same time rotating them to adjust for a uniform green vertical band at the center of the CRT screen. 7. Carefully slide the deflection yoke forward to achieve green purity (Uniform green screen). NOTE: Center purity is obtained by adjusting the tabs on the round purity magnet rings. Outer edge purity is obtained by sliding the deflection yoke forward. 8. Check for red and blue field purity by applying red and blue raster signal alternately from Dot/Bar Generator to receiver. Repeat steps 2 through 7, if required. 9. Tighten deflection yoke clamp screw. 10. Perform BLACK AND WHITE ADJUSTMENT procedure. ( CW : clockwise, CCW : counterclockwise )
FIG. 3 -7-
FIG. 4
-8-
WEDGE B
WEDGE C
RED GREEN BLUE
WEDGE A
WEDGE A
WEDGE B
BLUE GREEN RED
WEDGE B
WEDGE C
BLUE GREEN RED
WEDGE A
(B)
(D)
Fig. 5 FOCUS ADJUSTMENT Adjust focus control, located on the Horizontal Output Transformer (T671), for maximum overall definition and fine picture detail with Brightness and Contrast controls set at normal viewing levels. BLACK AND WHITE ADJUSTMENT (CUTOFF / WHITE BALANCE) The purpose of this procedure is to adjust the bias applied to the color picture tube for reproducing a quality monochrome picture at all brightness levels and also to achieve maximum usable brightness. Confirm that proper purity and AGC adjustments have been completed before starting this adjustment. Connect the TV test pattern generator (Monoscope pattern) to the EXT. antenna terminal via TV VHF/UHF signal generator (NTSC signal, 70dB u). 2. Select Cutoff Mode by remote control, (refer to page 4 for remote control key combination and position) and CUT OFF will be displayed on top-right screen for about 3 seconds. At the same time the data readings for Cutoff and Gain in Adjustment Mode (2) will become as follows: R CUTOFF: 50, G CUTOFF: 50, B CUTOFF: 50, G GAIN: 127, B GAIN: 127 3. Select Service Mode by remote control, (refer to page 4 for remote control key combination and position) and TV screen becomes horizontal line. 4. Turn the Screen control (located under the flyback transformer) clockwise until any blue, green or red color line appears. 5. Check the color of the line which appeared first, then turn the Screen control (located under the flyback transformer) fully counterclockwise. 6. Adjust the cutoff level of the color which appeared first by remote control, (refer to page 4 for remote control key combination and position) so that voltage between TP16 and TP15 (blue), TP14 (green) or TP13 (red) is 20 1V. 7. Turn the Screen control (located under the flyback transformer) clockwise so that the bright color line can just be seen. 8. Adjust cutoff levels other than the above by remote control, (refer to page 4 for remote control key combination and position) so that the line color is white. 9. Press again Service Mode key by remote control, (refer to page 4 for remote control key combination and position) to return to TV position. Monoscope pattern will appear on TV screen. 10. Adjust the contrast and brightness controls to make the picture dim. Adjust the Green and Blue Cutoff levels by remote control, (refer to page 4 for remote control key combination and position) so that the picture is white. 11. Adjust the contrast and brightness controls to make the picture bright. Adjust the Green and Blue Gain levels by remote control, (refer to page 4 for remote control key combination and position) so that the picture is white. 12. Repeat steps 10 and 11 so that the picture is white in both dim and bright conditions. 1.
-9-
HORIZONTAL PHASE ADJUSTMENT 1. Connect TV Test pattern Generator (NTSC signal 70dB u, Monoscope Pattern) to Antenna T erminal (TE) through TV Channel Generator. (NOTE: For steps 2, 3 and 4 below, refer to page 3 for Adjustment By Remote Control Method). 2. Go to Adjustment Mode (2) by remote control. 3. Select H. PHASE from Adjustment Mode (2) menu screen. 4. Adjust H. PHASE level (by using + or - button on remote control) so that horizontal reading of test pattern becomes the same value. VERTICAL PHASE ADJUSTMENT 1. Connect TV Test pattern Generator (NTSC signal 70dB u, Monoscope Pattern) to Antenna Terminal (TE) through TV Channel Generator. (NOTE: For steps 2, 3 and 4 below, refer to page 3 for Adjustment By Remote Control Method). 2. Go to Adjustment Mode (2) by remote control. 3. Select V. PHASE from Adjustment Mode (2) menu screen. 4. Adjust V. PHASE level (by using + or - button on remote control) so that vertical reading of test pattern becomes the same value. VERTICAL AMPLITUDE ADJUSTMENT 1. Connect TV Test pattern Generator (NTSC signal 70dB u, Monoscope Pattern) to Antenna Terminal (TE) through TV Channel Generator. (NOTE: For steps 2, 3 and 4 below, refer to page 3 for Adjustment By Remote Control Method). 2. Go to Adjustment Mode (2) by remote control. 3. Select V. AMP from Adjustment Mode (2) menu screen. 4. Adjust V. AMP level (by using + or - button on remote control) so that picture fills the picture opening from top to bottom and is proportionate to the width. RF AGC ADJUSTMENT 1. Connect TV Channel Signal Generator to Antenna Terminal (TE). 2. Connect positive lead of DC Digital Voltmeter to TP5 and negative lead of DC Digital Voltmeter to TP4. 3. Adjust level of TV Channel signal Generator so that the output level is 57dB u. (Monoscope Pattern) (NOTE: For steps 4, 5 and 6 below, refer to page 3 for Adjustment By Remote Control Method). 4. Go to Adjustment Mode (2) by remote control. 5. Select RF AGC from Adjustment Mode (2) menu screen. 6. Adjust RF AGC level (by using + or - button on remote control) so that the DC Digital Voltmeter reading is 6.0V 0.2V. SUB BRIGHTNESS ADJUSTMENT 1. Connect TV Test Pattern Generator (NTSC signal, Color Bar Signal, 70dB u) to EXT. Antenna Terminal through TV Channel Signal Generator. (NOTE: For steps 3, 4 and 5 below, refer to page 3 for Adjustment By Remote Control Method). 2. Go to Adjustment Mode (1) by remote control. 3. Set the COLOR and CONTRAST of the TV set to minimum and the SUB CONTRAST and SUB BRIGHT to '0' (using + or - button on remote control). 4. Adjust SUB BRIGHT level (by using + or - button on remote control) to obtain a dim pattern. (Refer to Fig.6)
DIM LIGHT
Fig. 6 - 10 -
TEST POINT
- 11 -
IC101
IC102 IC301
TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt
1 4.9 11 0.0 21 0.0 31 2.1 41 0.7 1 0.0 1 0.0 11 6.3 21 2.3 31 0.7 41 3.1 51 0.0 1 12.1 1 0.0 1 0.0 1 10.3
9 23.8
B Volt 0.1 -0.7 -0.1 3.9 1.5 1.6 0.0 2.5 2.3
E Volt 0.0 0.0 0.0 3.3 2.1 1.0 0.0 2.3 2.2
C Volt 4.7 3.9 4.5 9.0 0.0 9.0 9.0 122.6 129.3
- 12 -
CHASSIS WAVEFORM
- 13 -
SCHEMATIC DIAGRAM
PCB1 MAIN 4551-2011601D
R142 1k 1/4W VOUT C180 100p B VCC GND R126 22k RX101 REMOTE SENSOR
PCB2 CRT
R451 15k 1W MTL
! SU451
9 8 7
C454 1000p /2kV
! V451 CRT
R146 1 k 5V C109 R119 1k 1/4W 8.2p CH C107 100 /10V C104 27p CH C105 27p CH C106 30p CH 5V C108 0.022 ZF R101 4.7k R102 4.7k
C126 560p B
R G B R136 100k Q101 DTC143ZS C127 1000p B R137 15k R127 270k 1/4W
JL101A 5P
JL101B 5P R G B
6 5 4 3
Q102 2SC945 (P) R129 10k R120 1k R121 5.6k 1/4W BLK R122 B 5.6k 1/4W R123 G 5.6k 1/4W R124 R 5.6k 1/4W
9V JL101
9V
R459 R460 330 1.5k 1/6W 1/6W C452 470p B R472 220
R461 R462 330 1.5k 1/6W 1/4W C453 470p B R473 220
4.7/50V
R103 100 C103 R104 100 C101 0.1 C102 0.1 C112 680pB C111 680pB
X101 8MHz
L101 47uH
C177 270p
42
41
VIDEO INPUT
40
VIDEO INPUT
39
GND
38
SDA
37
SCL
36
H. SYNC
35
REMOTE
34
GND
33
RESET
32
XOUT
31
XIN
30
TEST
29
OSC1
28
OSC2
27
VD-OSD
26
ADJ MODE 3 HD-OSD
25
BLK
24
B
23
G
22
R
D306 1SS133
R181 33k
VCC
MENU COLOR
OSD CONT 1
OSD CONT 2
LANGUAGE
VCHIP SEL
POWER IN
MAIN/SAP
ST/MONO
TV/VIDEO
V-BLOCK
SERVICE
WF-2
4551-2011602D
POWER
KEY IN
V-SYS
GND
NC
NC
NC
AFC
NC
10
11
12
13
14
15
16
17
18
19
20
21
R106 22k
R105 1k
R110 22k
WF-7
C129 100p B
TP10 GND
JL102B
JL102
CN501
WF-5
L301 15 uH C511 100 /25V Q303 2SC945 (P) R307 330
WF-1
VIDEO TP8 R328 2.2k R329 5.6k R336 2.2k
R308 1k
C308 10 /50V C306 0.1 MYL D301 1S2473 R335 C304 0.01 68k 1/6W D303 1S2473 R340 1M C315 2.2 /50V D302 1SS133 X551 503KHz R331 180k 1/6W R570 390 C305 1 /50V H. VCC C562 1 /50V R551 2.2k 1/4W C551 0.01 ZF
4
OUTPUT STAGE
9
FLYBACK GENERATOR PULSE SHAPER
DRIVER STAGE
8
R563 330 2W MTL !
R305 3.3k
S101 POWER
R361 1k
C555 10 /50V
1000p MYL
C214 0.01 ZF
C361
R131 3.3k
VCC
SDA
SCL
S102 CH-UP
L361 5.6uH
R555 15k
C556 10 /50V
R132 3.3k
VSS
E0
E1
E2
R501 1k
R362 39K
IC102 M24C02
C213 4700p B
C231 0.01 ZF
R220 1k
C331 0.01
R675 1M
C130 100p
C674 10 /250V
T202 VCO
R554 47k
D552 RD6R8ES2
C512 100p B
WC
24V
R302 1.8k
C317 0.01
D553 1SS133
C504 470p B
R504 15k
C218 47p CH
WF-4
TP11 X-RAY R556 5.6k
C362 100p
2
C505 0.1 MYL
7
C508 1000 /25V
R113 10k
D501 1N4002E
C506 100/25V
WF-6
R463 3.3 ! 1W CEM FUSE
R509 1.5 1/4W C673 ! 3300p R673 /400V 2.2 1/4W 160V D673 1F4-E
56
55
54
53
52
51
SIF GND
50
49
48
SIF VCC
47
46
VCC
45
BPF AFT
44
43
CLAMP
42
41
40
39
38
37
36
35
34
33
32
H-OUT
31
30
29
X-RAY H.RAMP C510 3.3 /50V
S103 CH-DOWN
VCO 90 Q DET
WF-3
R133 5.6k
LIMIT
S104 VOL-UP
1 DET
9 6 5 7
AFC1
AFC2
ACC
R134 12k
TINT
LPF
BRIGHT MATRIX
11V
S105 VOL-DOWN
SW
CUTOFF
V. RAMP H.VCC
BUS
4
D672 1F4-E C671 3300p /400V
F 3 1 G 2 8
C326 1 /250V
S
R332 1k 1/4W TP1
3
T203
6
C211 4.7 /50V
10
11
12
13
X301 3.58MHz D312 1SS133
14
C341 0.1 /50V
15
16
C342 0.1 /50V
17
C343 0.1 /50V
18
19
R319 220 R320 220
20
R321 220
21
22
23
24
C552 2.2 /50V
25
26
R192 1k
27
R191 1k
28
OUT C664 100 /16V R614 680 1/4W 3 9V 1 2 IN R558 330 IC311 NJ7809FA VOLTAGE REGULATOR R612 4.7k 2W MTL Q551 2SC1473A (R)
WF-8
R562 C558 0.5 560p /500V T552 1/2W 3 4 1 6
D671 1F4-E
R322 3.3k
TP2
D308 1S2473
R212 10k
C320 0.022 ZF
C319 10p CH
D309 1SS133
D310 1SS133
D311 1SS133
R343 820
R342 820
D607 1SS133
WF-9
R559 330
Q552 2SD1877 !
R344 10k
TP3 IF
R341 820
SF201 45.75MHz
D559 RD9R1ES2
R613 4.7k 2W MTL 130V R674 1.8k 1W MTL C614 0.01 /250V KH IC601 ! STR30130 ! D601 RS104 ! C604 0.01 /250V KH !
C381 0.01ZF
R351 220
TP5 AGC
TP4 GND
Q351 DTC143ZS
C553 0.01 ZF
C221 0.01 ZF
C609 33 /160V
! L602 FILTER
3 2 4 1
R151 1k 1/4W
R1 220 1/4W
R3 10k
R152 1k 1/4W
C1 10 /50V
C4 4.7 /50V
R4 180k
C7 330 /16V
RL601 ! RELAY
33V R615 D606 47 1/4W 1S2473 R805 470 C8 22 /50V Q803 2SC2120 (O) C806 1000 /16V D801 1SS133 R808 1 1/6W ! R812 10 1/2W IC671 NJ7805LD PROTECT C804 220 /16V R810 2.2 C805 0.1 CN801 VOUT ! LCN801 ERROR F. BACK ROUT G CD START V RESET VIN !
1
R606 47 1/4W
5
R603 270 10W ! CEM
AGC UHV/VHF 75
SCL ! TU1
SDA
BM
BP
BT
IF
D8 HZT33
C802 47 /16V
C608 22 /160V
R806 150
! !
VHF/UHF/CATV
TUNER
R807 150
D602 1N4004E
R804 10k
4
C681 0.1 MYL
1
C678 100 /25V R611 680 1/2W D605 RD12ES2 C611 1000 /25V
! TE 1
SAFETY
THE DESIGN OF RECEIVER CONTAINS MANY CIRCUITS AND COMPONENTS INCLUDED SPECIFICALLY FOR SAFETY PURPOSES. FOR CONTINUED PROTECTION. NO CHANGES SHOULD BE MADE TO THE ORIGINAL DESIGN AND COMPONENTS SHOWN IN ! ON THE SCHEMATIC SHOULD BE REPLACED WITH EXACT FACTORY REPLA CEMENT PARTS. THE USE OF UNAUTHORIZED SUBSTITUTE PARTS MAY CREATE A SHOCKFIRE X-RAY RADIATION OR OTHER HAZARD. SERVICE SHOULD BE PERFORMED BY QUALIFIED PERSONNEL ONLY. RELIABLE AND PERFORMANCE FOR CONTINUED RELIABILITY AND PERFORMANCE EXACT FACTORY REPL ACEMENTS ARE RECOMMENDED FOR ALL OTHER PARTS REPLACED. IF A SUBSTITUT MUST BE USED E BE SURE ITS QUALITY AND SPECIFICATIONS ARE IDENTICAL TO THEORIGINAL PART.
SAFETY REQUIREMENTS COMPONENTS IN ACCORDANCE WITH PRESENT SAFETY REGULATIONS. THESE COMPONENTS. MOST ONLY BE REPLACED BY ORIGINAL PARTS.
16
L601 DEGAUSSING
5V
TH601
D315 1SS133
DEMO
WPL
V-SEP.
VC/D
R672 2.2 1W