Documente Academic
Documente Profesional
Documente Cultură
CaMMERClAli
p Indianapolis, Indiana 46206
.ENGlNE
BULLETIN
April 6, 1972 GEARBOX ASSEMBLY, NEW PINION BEARING CAGE-INSTALL PLANNING INFORMATION: EFFECTIVlTY: All 250-Cl8 and Cl8B Gearboxes prior to CAG22455. All 250-Cl8A and Cl8C Gearboxes prior to CAG 23552. All 250-B17 Gearboxes prior to CAG 60012. All 250-C20 Gearboxes prior to CAG 30390. Converted 250-C20 Gearboxes (identified by the letters BA following the gearbox serial number)-inspect and comply if necessary. REASGN: To prevent excessive bearing looseness and resulting wear in the pinion bearing cage. Cage wear can result in loose bearing fit, shaft spline wear and metal generation. Former cages, when manufactured and when repaired by plating the ID at overhaul, were finish machined in a fixture prior to being pressed into,the gearbox cover. The new pinion bearing cages have machining stock and are to be finish machiied after installation in the cover. Using this procedure of sizing the cages allows the pinion bearing fit to be improved to 0. OOOlL to 0.0007L on all engines. To accomplish these changes, the old pinion bearing cage is removed and the new cage is installed. The new cage ID is then finish machined while installed in the cover to provide 0. OOOIL to 0.0007L fit for the pinion bearing. Following incorporation of the new cage, the gearbox cover is reidentified. Revision No. 1 May 30, 1972
DESCRIPTION:
COMMERCIAL
ENGINE
BULLETIN
GEARBOX ASSEMBLY, NEW PINION BEARING CAGE-INSTALL COMPLLANCE: To be accomplished at overhaul when existing salvage procedures cannot be used to restore cage to limits and new cages are available. FAA-DER Approved No significant additional time will be required to accomplish this bulletin at time of overhaul.
AVAILABILITY: Model 250-Cl8 250-Bl?, C20 New P/N 6876941-1,2,3 6876936-1,2,3 Nomenclature Pinion Bearing Cage Pinion Bearing Cage i3z 1 1
TGGLING:
COMMERC
IAL
ENGINE
BULLETIN
Disassemble gearbox assembly as necessary to remove gearbox cover assembly. A. Remove P/N 6843359 Pmion Bearing Cage from P/N 6870734 or P/N 8851928 Cover (Cl8), P/N 6875494 Pinion Bearing Cage from P/N 6875493 Cover (Bl7, C20) or P/N 6875494 Pinion Bearing Cage from P/N 6876584 Cover (Converted C2Os). L Instsll new P/N 6876941 Cage in P/N 6870734 or P/N 6851928 Cover (Cl8) or new P/N 6876936 Cage in P/N 6875493 (Bl7> C20) or P/N 6876584 (converted C20) Cover. Select oversize as necessary per the following: Part No. 6876941-l 6876941-2 6878941-3 6876936-l
6876936-2 6876936-3
Oversize Mark
me----
+0.003 +0.006
mmDDem
Finish machine ID of installed cage to provide 0. OOOlL to 0.0007L pinion bearing fit. Cage IDs are as follows: 250-C18, Cl8A, Serviceable 2.4413 250-Bl7, C20 Nominal 2.6777
zmm
Cl8B,
Cl8C
Nominal 2.4413
zz?fm
Serviceable 2.6777
COMMERCIAL
ENGINE
BULLETIN
GEARBOX ASSEMBLY, NEW PINION BEARING CAGE-INSTALL B. Obliterate former cover assembly part number and reidentify follows per AS478-2Dl or 2E: Model Cl8 B17, C20 Converted C20 IL Former P/N 6851928 or 6870734 6875493 6876584 Reidentify As 6876940 6876935 6877707 as
Record compliance with 250 CEB-137 (Cl8), 250 CEB-1010 (C20) or 250 TP CEB-1008(Bl7) in the Gearbox Assembly (yellow pages), Modification Record, Part III of the Engine Log Book.
,, LlO LlLl5-lJl
C20 CEB-1010
COMMERCIAL
GEARBOX MATERIAL ASSEM.BLY,
ENGINE
NEW PINION
BULLETiNB1cEg;;;
BEARING CAGE-INSTALL
INFORMATION: !iEz
New P/N
1
1 1 1 1
Qty Alt I 1
1
Disposition 1 1
1
Assy, Gearbox
6843359-1,2,3 6875494-1,2,3
1 1
2 2
Stock Disposition 1. 2.
When necessary,