Documente Academic
Documente Profesional
Documente Cultură
Page 1 of 23
Service
Engine Warranty Maintenance Statement
Maintenance, repair, or replacement of the emission control devices and systems on this engine, which are being done at the customers expense, may be performed by any nonroad engine repair establishment or individual. Warranty repairs must be performed by an authorized John Deere dealer.
Service Intervals
Check engine oil. Check hardware. Adjust belt guides. Replace auger drive belt. Replace traction drive belt. Replace shear bolt. Adjust chute worm drive. Before Each Use Or As Required Adjust chute control rod. Adjust spout control lever. Adjust carburetor. Adjust friction wheel. Replace friction wheel. Reverse scraper blade. Clean fuel cap vents. Check gearbox lubricant. After First 2 Hours Of Operation Change engine oil.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service Adjusting Carburetor Checking Gearbox Lubricant Adjusting Auger Drive Belt Adjusting Belt Guides Replacing Auger Drive Belt Replacing Traction Drive Belt Adjusting Friction Wheel Replacing Shear Bolt Reversing Scraper Blade Adjusting Traction and Auger Drive Cable Lubricating Friction Disc Hub Lubricate Auger Shaft Lubricate Wheel Axle Filling Fuel Tank Safely Filling Fuel Tank Check Tire Pressure DATE SERVICE PERFORMED 10 Hours Lubricate snowblower Adjust auger drive belt Check spark plug. Change engine oil. Check tire pressure. 25 Hours Or At End Of Season Lubricate friction disk hub zerk. Check auger and traction cable adjustments. Lubricate auger shaft. Lubricate wheel axle. Check hardware. Lubricate snowblower. Check auger drive belt adjustment. Check traction and auger cable adjustments.
Page 2 of 23
Service Record
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 3 of 23
Avoid Fumes
c CAUTION: Avoid injury! Engine exhaust fumes can cause sickness or death: If it is necessary to run an engine in an enclosed area, use an exhaust pipe extension to remove the fumes. Always try to work in a well ventilated area.
Engine Oil
Use oil viscosity based on the expected air temperature range during the period between oil changes. The following John Deere oil is preferred:
The following John Deere oils are also recommended, based on their specified temperature range: TURF-GARD (SAE 10W-30) PLUS-4 (SAE 10W-30)
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service TORQ-GARD SUPREME (SAE 30) Other oils may be used if above John Deere oil is not available, provided they meet one of the following specifications: SAE 5W-30-API Service Classification SG or higher SAE 10W-30-API Service Classification SG or higher SAE 30-API Service Classification SC or higher
Page 4 of 23
Grease
Use grease based on the expected air temperature range during the service interval. The following greases are preferred: John Deere Moly High Temperature EP Grease. John Deere High Temperature EP Grease. John Deere GREASE-GARD. Other greases may be used are: SAE Multipurpose EP Grease with 3 to 5 percent molybdenum disulfide. SAE Multipurpose EP Grease. Greases meeting Military Specification MIL-G-10924C may be used as arctic grease.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service TS1417
Page 5 of 23
M96036 2. Remove dipstick (A). Wipe it. 3. Check engine oil: Install and tighten dipstick.
M71567 Remove dipstick. Check oil level. Oil should be between ADD and FULL marks on dipstick. 4. Add oil if necessary. (See Engine Oil in this section for correct oil.) 5. Install and tighten dipstick.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Page 6 of 23
M96036 5. Remove dipstick (B). 6. Drain oil into container. Install drain cap. 7. Add 0.6 L (19 oz) of oil through dipstick tube. (See Engine Oil in this section). 8. Install and tighten dipstick.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service M71567 9. Remove dipstick. Check oil level. Oil should be between ADD and FULL marks on dipstick. 10. Install and tighten dipstick.
Page 7 of 23
c CAUTION: Avoid injury! Before you remove spark plug: STOP engine Let engine cool
M96036 1. Disconnect spark plug wire (A). Remove plug (B). 2. Inspect plug for wear or damage. Replace plug if needed. 3. Adjust gap: 0.76 mm (0.030 in.). 4. Install and tighten plug to 27 Nm (20 lb-ft). 5. Connect plug wire.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service Let engine cool. DO NOT smoke while working on fuel system.
Page 8 of 23
M62527 1. Remove cap. 2. Clean vents (A) in nonflammable solvent. 3. Install cap.
Adjusting Carburetor
NOTE: The carburetor is calibrated by the engine manufacturer and should not require any adjustments. If engine is operated at altitudes above 1829 m (6,000 ft.), some carburetors may require a special high altitude main jet. See your John Deere dealer. Possible engine surging will occur at high rpm when the machine is in neutral ("N") and the auger is disengaged. This is a normal condition due to the emission control system. If engine is hard to start or runs rough, check the TROUBLESHOOTING section of this manual. After performing the checks in the troubleshooting section and your engine is still not performing correctly, contact your John Deere dealer.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 9 of 23
M71588 1. Remove check plug (A). 2. If you cannot see grease, use a wire or plastic tie strap to check for grease. If you can see grease on wire or tie strap, do not add grease. 3. If necessary, add John Deere High Temperature EP Grease 100 gr (3-1/2 oz) maximum when gearbox is empty or an equivalent, such as: Benalene No. 372 Shell Darina 1 Mobiltem 78 Texaco Thermatex EP1 4. Install check plug.
NOTE: If you do not operate snowblower 25 hours during season, adjust auger drive belt at end of season. 1. Disconnect spark plug wire.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 10 of 23
M60921 2. Loosen screw (A) on each side of belt cover (B). Remove cover.
M71569a 3. Hold down auger drive lever so idler pulley (C) is engaged. Check belt deflection. Belt should deflect 13 mm (1/2 in.) (D) with moderate thumb pressure. 4. Adjust belt, if necessary:
M96038 Loosen nut (E). Move pulley (F) toward belt 3 mm (1/8 in.).
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service Tighten nut. Check deflection again. 5. Check belt guides (G) adjustment. (See Adjusting Belt Guides in this section.) 6. Install belt cover.
Page 11 of 23
M60921 2. Loosen screw (A) on each side of cover (B). Remove cover. 3. Hold auger drive control lever down to handle.
M71575a 4. Measure distance between belt guide (C) and belt. Distance should be 3 mm (3/32 in.). If it is not, loosen guide mounting bolt (D), adjust guide, and tighten bolt.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 12 of 23
M60921 1. Disconnect spark plug wire. 2. Loosen screw (A) on each side of cover (B). Remove cover.
M96038 3. Loosen nut (C). Move pulley (D) away from belt.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 13 of 23
M96038 5. Remove belt (F) from engine drive pulley (G). 6. Remove top two housing bolts (H), and loosen bottom two bolts (I). Separate auger housing from engine frame hinging on bottom 2 bolts. 7. Remove brake arm (J) from housing. DO NOT remove spring. 8. Remove old belt. 9. Position new belt on auger pulley. 10. Install brake arm. Be sure brake arm is pushed into housing, and brake pad is seated in pulley groove. 11. Position belt onto engine drive pulley. 12. Install auger housing to engine frame with top two bolts. Tighten bottom two bolts. 13. Adjust belt. (See Adjusting Auger Drive Belt in this section.) 14. Adjust belt guides. (See Adjusting Belt Guides in this section.) 15. Install cover. Connect plug wire. 16. Check auger drive cable adjustment. (See Adjusting Auger And Traction Drive Cable in this section.)
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 14 of 23
M60921 2. Loosen screw (A) on each side of cover (B). Remove cover. 3. Loosen belt guides. Move them away from belt.
M96038 4. Loosen nut (C) and move pulley away from auger drive belt (D). 5. Take auger drive belt off of engine pulley (E). 6. Pull and hold idler pulley (F) away from traction drive belt (G). Pull belt past pulley. 7. Remove belt from engine pulley. 8. Remove belt from between bottom of large pulleys. 9. Install new belt on bottom of large pulley and onto engine pulley. 10. Pull idler pulley toward you and slip belt past pulley. 11. Release idler. 12. Install auger drive belt on engine pulley.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 15 of 23
13. Adjust auger drive belt pulley. (See Adjusting Auger Drive Belt in this section.) 14. Adjust belt guides. (See Adjusting Belt Guides in this section.) 15. Install cover. Connect plug wire. 16. Check traction drive cable adjustment. (See Adjusting Traction And Auger Drive Cable in this section.)
c CAUTION: Avoid injury! Snowblower may be heavy. If necessary, have another person help you stand snowblower on end. NOTE: Do this service when there is only a small amount of fuel in fuel tank. 1. Move speed selector lever to first (1) speed. 2. Stand snowblower on end of auger housing. 3. Remove bottom panel:
M60926 Remove rear bolts (A). Loosen bolts (B). Remove panel.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 16 of 23
M71581 4. Check position of friction wheel. Right side of disc drive plate (C) should be 76 mm (3 in.) (D) from center of friction wheel (E).
M60925 5. To adjust position of friction wheel: Loosen two nuts (F) on speed selector lever. Move friction wheel to proper position. When position is correct, tighten nuts. 6. Install bottom panel.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service NOTE: Two extra shear bolts are in the bag of parts included with your snowblower. 1. Stop engine.
Page 17 of 23
M71588 2. Remove broken shear bolt (A), if necessary. 3. To help prevent auger from rusting, lubricate auger shaft at two shear bolt points and at end of each shaft with a lightweight oil. Turn auger on shaft several turns to help distribute oil. 4. Line up holes in auger with hole in auger shaft.
M71579 5. Install new bolt with spacer (B) under bolt head. Fasten bolt with lock nut (C).
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 18 of 23
M71585 2. Remove five nuts (A), lock washers, and bolts. 3. Reverse blade. Install and tighten hardware. 4. Remove blocks.
To check adjustment:
M71572 Pull on spring and remove cable end (Z fitting) (A) from bracket hole. Push control lever all the way forward so it contacts the plastic bumper. Pull cable straight and put end of cable-the Z fitting- on top of hole. Center of Z fitting should be between center and top of hole (B). To adjust cable:
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Page 19 of 23
M71586 Turn nut (C) to adjust cable to correct length. Install cable end in bracket hole.
M71581 Lubricate friction disc hub zerk (A) with one or two shots of John Deere Moly High Temperature EP Grease or an equivalent. (See Grease in this section.)
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 20 of 23
M71588 Remove two shear bolts (A). To help prevent auger from rusting, lubricate auger shaft at two shear bolt points and at the end of each shaft with a lightweight oil. Turn auger on shaft several turns to help distribute oil.
c CAUTION: Avoid injury! Snowblower may be too heavy for you. If necessary, have another person help you stand snowblower on end. NOTE: Do this service when there is only a small amount of fuel in fuel tank. 1. Stand snowblower on end of auger housing. 2. Remove both wheels.
M71573 3. Lubricate both axles (A) with John Deere Moly High Temperature EP Grease or an equivalent. (See Grease in this section.) 4. Install wheels.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 21 of 23
c CAUTION: Avoid injury! Handle fuel with care, it is highly flammable: DO NOT refuel machine while you smoke, when machine is near an open flame or sparks, or when engine is running. STOP engine. Fill fuel tank outdoors. Prevent fires: clean oil, grease and dirt from machine. Clean up spilled fuel immediately. Do not store machine with fuel in tank in a building where fumes may reach an open flame or spark. To prevent fire and explosion caused by static electric discharge, while you fill tank, use a non-metal fuel container. If you use a funnel, MAKE SURE it is PLASTIC. Avoid using a funnel which has a metal screen or filter. Use only clean approved containers and funnels. Store oil and fuel in an area protected from dust, moisture and other contamination.
IMPORTANT: Avoid damage! Avoid spilling fuel. Fuel can damage plastic and painted surfaces. DO NOT mix oil with gasoline. Unleaded gasoline with an octane rating of 87 or higher is recommended. Fuel tank capacity is 1.9 L (2 qt.).
Use only clean, fresh, unleaded regular grade gasoline. Remove any trash from top of fuel tank drain area. Use summer blended fuel for warm weather operation and winter blended fuel for cold weather. Never use fuel that is stale or has been stored for a long period of time: Warm Weather - Maximum 60 days. Cold Weather - Maximum of 90 days.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service Fill fuel tank at the end of each day's operation. This helps to keep condensation out of fuel tank. Oxygenated Fuel
Page 22 of 23
Oxygenates (either ethanol or MTBE) are added to the gasoline. If you use the oxygenated fuel be sure it is unleaded and meets the minimum octane rating requirement. The following are the EPA approved percentages of fuel oxygenates: ETHANOL (Ethyl or Grain Alcohol): You may use gasoline containing up to 10 percent ethanol by volume. MTBE (Methyl Tertiary Butyl Ether): You may use gasoline containing up to 15 percent MTBE by volume.
c CAUTION: Avoid injury! Allow engine to cool before refueling machine. 1. STOP engine. If engine is hot let it cool several minutes before you add fuel.
3. Fill fuel tank to 13 mm (1/2 in.) below bottom of filler neck to allow room for gasoline to expand. 4. Install fuel tank cap.
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013
Service
Page 23 of 23
M62509 Check tires for damage. Check tire pressure with an accurate gauge. Tire pressure should be 110 kpa (15 psi).
http://manuals.deere.com/cceomview/OMM137000_G8/Output/OMM137000_G87.html
2/10/2013