Documente Academic
Documente Profesional
Documente Cultură
As of 27 June 2001
This standard specifies the requirements for hot-rolled deformed rerolled steel bars used for
concrete reinforcement.
2 References
3 Classification
Deformed rerolled steel bars shall be classified into grades 170 and 230.
4 Requirements
4.1 Materials - Rerolled steel bars shall be manufactured by rerolling any of the following
materials:
4.2 Mechanical properties - Rerolled steel bars shall conform to the mechanical requirements
specified in table 1.
4.3 Appearance
4.3.1 The steel bars shall be free from defects injurious to use.
CDPNS 211:2001
4.3.2 Rust, seams, surface irregularities, or mill scale shall not cause rejection, provided the mass,
dimensions, cross-sectional area and tensile properties are not less than the requirements of this
standard.
The surface protrusions, (the axial protrusion among surface protrusions is called a rib and any
other, a lug) shape, size, mass and tolerances of deformed steel bars shall conform to the following:
4.4.1 The lugs shall be distributed over the entire length of the rerolled deformed bar at uniform
distances, and shall have the same shape and dimensions. When characters or the like are
embossed, the lugs at these locations may be omitted.
4.4.2 The angle of the lugs to the axis of the bar shall not be less than 45 degrees.
4.4.3 The spacing between the neighboring lugs of deformed bar shall be 7 mm.
4.4.4 The sum of the gaps of deformed bar shall not be more than 25% of the nominal perimeter
of deformed bar.
NOTE: If the rib and the lug are separated, and the deformed bar has no rib, the width of defect of
the lug shall be considered the gap, and if the lug and the rib are connected, the width of the rib shall
be considered to be the gap of the lug.
4.4.5 The minimum height of lug shall be 4.0% of the nominal diameter.
4.4.6 The size, unit mass and permissible limits of lugs shall conform to table 3.
2
CDPNS 211:2001
4.5.1 The length of the individual steel bar shall be 6 m and the tolerance shall be ? 40 mm.
4.5.2 The mass tolerance of one piece of steel bar shall be ? 10 percent.
4.5.3 The mass tolerance of one lot of steel bars shall be ? 7 percent.
5 Sampling
6 Test methods
6.1 The deformation measurements shall be determined in accordance with annex B of PNS 49.
6.2 The steel bar shall be tested for mechanical properties in accordance with annex C of PNS
49.
7 Markings
7.1 Deformed bars shall bear the manufacturer’s mark and bar sizes as follows:
7.1.1 Name of company - A logo or symbol registered with the Bureau of Product Standards
(BPS) and/or the Intellectual Property Office (IPO).
7.1.3.1 For 6 mm - There shall be one filled space between deformations to be placed beside the
logo.
Logo Space Filled
Space
3
CDPNS 211:2001
7.1.3.2 For 7 mm, there shall be two filled spaces between deformations to be placed beside the
logo.
7.1.3.3 For 8 mm, there shall be three filled spaces between deformations to be placed beside the
logo.
The height of the filled space shall be the same height as the deformations shown in figures 1, 2, and
3.
Each set of marks shall be placed at a distance not exceeding one meter from each other throughout
the active length of each bar.
7.2 The following color codes for deformed bar sizes shall be painted on the surface of both ends
of each bar:
6 blue
7 orange
8 violet
7.4 Other marks shall be indicated on the tag securely attached to each bundle of bars, each
bundle shall be composed of bars of the same size and grade.