Documente Academic
Documente Profesional
Documente Cultură
WTP-150
TABLE OF CONTENTS
1. Parts Identications 2. Setting up the printer 2.1 Unpacking 2.2 Connecting the cables 2.3 Loading the roll paper 2.4 Dip switch setting 3. Control panel and other functions 3.1 Control panel 3.2 Error Indicating 4. Self Test 5. Hexadecimal Dump 6. Specications 6.1. General Specications 6.2. Auto Cutter Specications 6.3. Interface 6.4. Electrical Characteristics 6.5. Environmental Requirements 6.6. Reliability 6.7. Certication 7. Command List 3 4 4 5 9 11 18 18 18 19 20 21 21 23 23 23 24 24 24 25
The Printer
User's Manual
Roll Paper
Adaptor(Option)
Interface Cable(optional)
Before connecting any of the cables, make sure that both the printer and the computer are turned off.
<Centronics Parallel>
<USB B Type>
<Ethernet>
Ethernet Interface
PIN 1 2 3 4 5 6 7 8
<USB COMBO>
<Wi->
Serial Interface
PIN 2 3 4, 20 6 1, 7 PIN 1 2 3 4 SIGNAL TXD RXD DTR DSR GND SIGNAL +5V DATADATA+ GND I/O Output Input Output Input I/O DESCRIPTION Printer transmit data line RS-232C level Printer receive data line RS-232C level Printer handshake to host line RS-232C level Data Send Ready System Ground DESCRIPTION +5V Printer transmit data line Printer transmit data line System Ground
SIGNAL Data Out + Data Out GND Data IN + Data IN N.C N.C N.C
I/O Output Data + Output Data Ground Input Data + Input Data -
USB Interface
PIN 1 2 3 4 5 6
SIGNAL Signal GND Drawer kick-out drive signal 1 Drawer open/close signal +24V Drawer kick-out drive signal 2 Signal GND
Caution : To avoid an overcurrent, the resistance of the drawer kick-out solenoid must be 24 or more. 3. Remove the used paper roll core if there is one inside. 4. Insert new paper roll as shown.
6. Pull out a small amount of paper, as shown. Then, close the cover.
Note : Power off. And open the cover of Dip Switch and change setting.
Baudrate selection
7. Tear off the paper as shown.
Transmission speed 4800 bps 9600 bps 19200 bps 38400 bps Print Density Low Power Normal Normal Dark
10
11
Baudrate selection
Transmission speed 4800 bps 9600 bps 19200 bps 38400 bps Print Density Low Power Normal Normal Dark
Transmission speed 4800 bps 9600 bps 19200 bps 38400 bps Print Density Low Power Normal Normal Dark
Print Density
--------------------------------------------------------------------------------------------------
12
13
Cutter
ON FULL CUT
Emulation
(*1) The detecting function of [Paper Low] is an option. Please set Dip Switch (2-6) [OFF] if you don't need any option. If Dip Switch is [ON] without any special option purpose. Printer detects [Paper is Low] and it could cause error.
14
15
3. Turn screw with drivers to a direction until paper is released from the cutter.
3. Set the switches using a pointed tool, such as tweezers or a small screwdriver. 4. Replace the DIP switch cover. Then, secure it with the screw. The new settings take effect when you turn on the printer.
16
17
Control Panel
Button
This section explains the different patterns signaled by the three LED indicators located on the top cover of the printer. STATUS Power off Power on On line Cover open Paper empty Paper near end Test mode PAPER RED OFF OFF OFF OFF OFF ON OFF ERROR RED OFF OFF OFF ON ON OFF OFF POWER GREEN OFF ON ON ON ON ON ON REMARKS Normal power is not supplied to the printer Normal power is supplied to the printer Normal error-free mode Close cover Insert new paper roll Paper is low Ignored error led
18
19
Hexadecimal Dump
(5) Number of print columns. No. of columns Font A 180 DPI 203 DPI (6) Roll paper 42 48 Font B 56 64
Refer to chapter 2 for details on the recommended roll Paper. Paper width : 50mm~82.5mm Roll diameter : Max. 83mm 1.7Kg
(7) Weight
20
21
RS232C Serial Interface, Centronics Parallel Interface(IEEE1284), USB Interface USB COMBO Interface, Ethernet Interface(10Mbps), Wi-(802.11b) (1) Input Voltage
6-3. Interface
DC 24V 10%
Operating: Approx. 1.5 A (at ASC printing) Peak : Approx. 10 A (at print duty 100%, For 10 seconds or less) Stand-by : Approx. 0.15 A
22
23
Important!
(2) Transport/Storage (except paper) Temperature -20C to 60C Humidity 10% to 90% RH (without condensation)
(1) MCBF
6-6. Reliability
60 million lines (based on an average printing rate of 12.5% with paper thickness in the range of from 65m - 75m) 35 million lines (based on an average printing rate of 12.5% with paper thickness in the range of from 76m - 150m) 100 million pulses, 100Km 1.0 million cuttings (if the paper thickness is between 65 and 90m)
(1) FCC PART15 CLASS A (2) CE EMCD/LVD (3) UL/cUL (4) MIC
6-7. Certication
24
25
1 2 3 4 5 6 7 8 9 10
FS 2 c1 d1dk
FS C FS S 1 2 FS W
Full cut Partial cut Set print mode(s) for Kanji characters Select Kanji character mode Turn underline mode on/off for Kanji character Cancel Kanji character mode Dene user-dened Kanji characters Select Kanji character code system Set Kanji character spacing Turn quadruple-size mode on/off for Kanji character
26
www.miniprinter.com
Rev. 3.0