Documente Academic
Documente Profesional
Documente Cultură
Pgina 1 de 4
Memory specifications
The HP LaserJet 2100 products support the following DIMM types: EDO: (Extended Data Output) technology that retains data in memory while the processor continues with other operations. This memory is single-tasking. Specifications: EDO: 100 pin, 32 bit, 60ns, 3.3 volts, 1K refresh rate top
Ordering information
Memory DIMMs can be ordered directly from www.hp.com . Part number 4 MB C4135A 8 MB C4136A 16 MB C4137A
Description or use The HP LaserJet 2100 printer comes with 4 MB of memory and can be expanded to 52 MB with the three available memory (DIMM) slots. The HP LaserJet 2100M and 2100TN printers come with 8 MB of memory and can be expanded to 40 MB with the two available memory (DIMM) slots.
The PS DIMM includes 4 MB of memory. This comes C3098installed in the HP LaserJet 2100M, and 2100TN printers. 60001
https://h30125.www3.hp.com/hpcsn/km/utils/ViewDocument.aspx?code=TINF:8:AR... 31/05/2009
Pgina 2 de 4
Installing memory
CAUTION:Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic wrist strap or frequently touch the surface of the DIMMs' antistatic package and then touch bare metal on the printer. 1. Print a configuration page to find out how much memory is installed in the printer before adding additional memory. After the configuration page prints, turn the printer off and disconnect the power cord (Figure 1). Figure 1: Disconnecting the power cord
2.
3.
Open the interface cable door (Figure 2) by pressing on the release tabs. Disconnect all interface cables. Figure 2: Opening the interface cable door
4.
Open the top cover. (Figure 3) Figure 3: Opening the top cover
5.
Press the RELEASE button and slide the right side panel forward until the alignment arrows line up. (Figure 4) Figure 4: Aligning the side panel
6.
Pull the panel away from the printer (Figure 5), exposing the available DIMM slots. Figure 5: Pulling the panel away from the printer
https://h30125.www3.hp.com/hpcsn/km/utils/ViewDocument.aspx?code=TINF:8:AR... 31/05/2009
Pgina 3 de 4
7.
Remove the DIMM from the antistatic package. (Figure 6) Figure 6: Removing the DIMM from the package
8.
Holding the DIMM by the edges, align the notches on the DIMM with the DIMM slot (check that the locks on each side of the DIMM slot are open). (Figure 7) Figure 7: Aligning the DIMM
9.
NOTE: For best results, use DIMM Slots in 1-2-3 order. Press the DIMM straight into the slot (press firmly). (Figure 8) Make sure that the locks on each side of the DIMM snap inward into place. (To remove a DIMM, the locks must be released.) Repeat Steps 6, 7, and 8 for each DIMM that is being installed. Figure 8: Pressing the DIMM into the slot
10.
To replace the side panel, line up the alignment arrows and slide the panel backwards until the RELEASE button latches into place. Close the top cover. (Figure 9) Figure 9: Replacing the side panel
https://h30125.www3.hp.com/hpcsn/km/utils/ViewDocument.aspx?code=TINF:8:AR... 31/05/2009
Pgina 4 de 4
11.
Reinstall the interface cable(s) and power cord.(Figure 10) Turn on the printer. Figure 10: Reinstalling the cables
top
2. 3.
4.
https://h30125.www3.hp.com/hpcsn/km/utils/ViewDocument.aspx?code=TINF:8:AR... 31/05/2009