Documente Academic
Documente Profesional
Documente Cultură
0)
You will need the following tools: The rework jig, the SS-93, metal tweezers, a torx plus screwdriver size 6, the SS-42 camera removal tool, a dental pick and a DC plug.
Gently release both plastic clips of the A-COVER ASSEMBLY with the SS-93.
Release the KEYMAT and cover the inner side window with a plastic film.
Carefully release the four hooks of the UI PWB HOLDER and lift it out.
Push down on the locking clip as shown. The UI PWB can now be slid out.
Use the dental pick to ease up the EARPIECE, and remove it with tweezers
Carefully unlock the VOLUME KEY with a twisting and pushing motion of the SS-93 and remove it.
Release the clips securing the IHF LID ASSEMBLY with the dental pick and remove the assembly.
Use the dental pick to ease up the IHF speaker, and remove it with tweezers.
Use the other end of the SS-42 to lift the CAMERA MODULE out.
ASSEMBLY
You will need the following tools: The soldering jig, the SRT-6, the SS-93, metal tweezers, a torque screwdriver with a torx plus size 6 bit and a DC Plug.
Use the rework jig while working with the CAMERA MODULE.
Insert the CAMERA MODULE into its seating, paying attention to the alignment tab.
Note the alignment tab. Press the speaker gently into position when it is aligned.
Fit the IHF LID ASSEMBLY: push it lightly into place and ensure that all snaps are engaged.
Remove the protective film and place the LCD in the UI SHIELD.
Place the UI SHIELD ASSEMBLY on the engine module, snap it into position, ensuring that the display connector is closed correctly.
Insert the four screws of the engine module.To prevent damage to the plastic threads, first turn the screws slightly to the left to engage the threads, then tighten them lightly.
Place the assembly in the B-COVER and click all the snaps into place.
Fit the A-COVER, beginning from the top and snap it closed.
Complete the assembly with the C-COVER, beginning from the top.
Exploded view
Troubleshooting
Power & connections
Power on
Battery Connector Check and clean the spring contacts of the Battery Connector.
Power Switch Check the mechanical and electrical condition of the Power Switch. Replace the Power Switch if necessary (Level 2 only).
Power Key Check the mechanical condition of the Power Key. Replace the Power Switch if necessary.
Charging
DC Jack Check and clean the spring contacts of the DC-Jack. Replace the DC-Jack if necessary.
DC Jack pads Check and clean the pads on the Engine Module.
Battery Connector Check and clean the spring contacts of the Battery Connector.
Fuse (L2) Check the resistance of the Fuse 0 .If the value does not match, replace the Fuse (Level 2 only).
Service GSM
GSM Antenna Pins Check and clean the GSM Antenna Pins on the Antenna Assy. Replace the Antenna Assy if necessary.
SIM
SIM Connector (Level 2 only) Check and clean the contacts of the SIM Connector on the Engine Module. Replace the SIM Connector (Level 2 only) if necessary.
SIM Grip Check the mechanical condition of the SIM Grip. Replace the SIM Grip if necessary.
Display Connector (Level 2 only) Check and clean the Display Connector on the Engine Module. Replace the display connector (Level 2 only) if necessary.
LCD Module Check and clean the LCD Module and Connector. Replace the LCD Module if necessary.
Keymat
Board to Board Connector Check and clean the Board to Board Connector on the Engine Module. Replace the board to board connector (Level 2 only) if necessary.
UI Module Assy Check and clean the pads on the UI Module Assy. Replace the UI Module Assy if necessary
Domesheet Check and clean the Domesheet on the UI Module Assy. Replace the UI Module Assy if necessary.
UI B2B Holder Check the mechanical condition of the UI PWB Holder. Replace the UI PWB Holder if necessary.
Keymat Check the mechanical condition of the Keymat. Replace the Keymat if necessary.
Earpiece
Earpiece pads Check and clean the Earpiece Pads on the Engine Module.
Earpiece Check and clean the spring contacts of the Earpiece. Replace the UI Shield Assy if necessary.
IHF Speaker
IHF Speaker pads Check and clean the IHF Pads on the Engine Module.
IHF Pin Check and clean the IHF Pin in the IHF Lid Assy. Replace the IHF Lid Assy if necessary.
IHF Speaker Check and clean the spring contacts of the IHF Speaker. Replace the IHF Speaker if necessary.
Microphone
Microphone Pads Check and clean the Microphone Pads on the Engine Module.
Microphone Check and clean the spring contacts of the Microphone. Replace the Microphone if necessary.
Volume
Switch (Level 2 only) Check the mechanical and electrical condition of the Switch. Replace the Switch (Level 2 only) if necessary.
Volume Key Check the mechanical condition of the Volume Key and Actuator. Replace the Volume Key if necessary.
Camera Connector Check and clean the VGA Camera Connector on the Engine Module.
Camera Check and clean the Lens and pads of the VGA Camera Module. Replace the Camera Module if necessary.
Vibra
Vibra Pads Check and clean the Vibra Pads on the Engine Module.
Vibra Motor Check and clean the spring contacts of the Vibra. Replace the Vibra if necessary.