Sunteți pe pagina 1din 13

General Information

The Teccor SIDACtor is a solid state transient voltage protector designed for use in telephony, data, and some AC applications. The SIDACtor is a bidirectional device that is normally connected to the high side of a circuit and a common. The SIDACtor remains in a high off-state impedance (leakage current <5A) until it senses a voltage exceeding its voltage breakover (VBO). Upon sensing an overvoltage, the SIDACtor will clamp the voltage and transition through a positive or negative zener region until enough current is present to allow the device to crowbar into a low impedance state. The typical voltage drop across the device during full conduction is typically less than 5 volts. The SIDACtor will return to its high impedance state when the current is interrupted or falls below the minimum holding current of the device. SIDACtor performance does not degrade with time, bias, number of operations or surges within the devices Peak Pulse Current rating. It should be noted that the SIDACtor will fail short if the device is subjected to a surge that exceeds its rated Peak Pulse Current (IPP) or Peak One Cycle Surge Current (ITSM). SIDACtors are available in breakdown voltages ranging from 30 to 540 volts and Peak Pulse Current ratings up to 500 amps (2x10S). Tape-and-reel packaging is available for the TO-92 and TO-220 packages along with embossed carrier reel packing for the DO-214AA.

Please consult the factory for more information.

Features
Bidirectional Transient Voltage Protection Breakover Voltages from 27 - 540 Volts Patented Multi chip packages Robust Surge Current Capabilities ION Implant Technology Clamping speeds of nanoseconds Electrically Isolated Package Glass-passivated Junctions

Teccor Electronics, Inc.

Electrical Parameter Terminology

VBO Breakover Voltage VBO (MIN) Minimum voltage point at which the SIDACtor may begin to conduct VBO (MAX) Maximum voltage required to begin conduction IBO Breakover Current Current through the SIDACtor at the breakover point (VBO) IPP Peak Pulse Current Maximum rated impulse current ITSM Peak One Cycle Surge Current SIDACtors maximum one cycle AC surge current rating IT On-state Current Continuous on-state current rating of the SIDACtor VT On-state Voltage Voltage drop across the device at rated on-state current IH Holding Current Minimum current required to maintain the SIDACtor in the on state CO Off-state Capacitance SIDACtors typical off-state capacitance di/dt Critical Rate-of-rise On-state Current Maximum rated rate-of-rise current VF Forward Voltage Maximum forward voltage across the P0641SA SIDACtor while in the on state (See Figure 3C on page 13.)

Teccor Electronics, Inc.

Ordering Information
Part Number Definition

Device Packing Options


Package Type TO-92 Bulk Pack Tape and Reel Pack Tape and Ammo Pack TO-220 Bulk Pack Clear Plastic Magazine or Tube Pack Tape and Reel Pack Tape and Reel Pack for Type 61 Leadform DO-214AA Embossed Carrier Reel Pack Bulk Pack Description Packing Quantity 2000 2000 2000 500 50 700 700 2500 5000 TP RP RP RP RP AP Added Suffix Optional Standard Option Option Standard Option Option Option Standard Option Industry Standard None EIA RS-468-A EIA RS-468-A None None EIA RS-468-A EIA RS-468-A EIA-481-1 None

Detailed packaging drawings are available from the factory upon request. *Standard lead spacing is .200" for TO-92 Reel Pack. For other spacing requirements please contact the factory.

Teccor Electronics, Inc.

Testing
Quality Assurance
100% Testing is a constant monitor for Quality Assurance.

Test Description
1. Surge (IPP)

Condition
@ Rated Current VBO and absolute peak in forward and reverse directions Measured for a minimum value as rated Measured with 1 Amp RMS or DC current Breakover leakage and off-state leakage

Comments
Repeated 2 times in the normal sequence of testing, except for TO-220 which is repeated 4 times. All devices fully characterized on voltage to ensure proper operation and reliability This ensures proper delatch (turnoff) after surge current condition.

2. Breakover Voltage (VBO) 3. Holding Current (IH) 4. Peak On-State Voltage (VTM) 5. Leakage Current (IDRM)

These tests ensure long term reliability.

Teccor Electronics, Inc.

Electrical Specifications

VBO
Breakover Voltage (Instantaneous Clamping Voltage) (1)(3)(13) Volts PINS 1 to 3
MIN P0300EA70 P0640EA70 P0720EA70 27 58 65 75 90 120 140 190 220 275 300 190 220 275 300 140 MAX 36 70 80 95 125 145 170 265 300 350 400 265 300 350 400 170

IBO
Breakover Current

IPP
Peak Pulse Current TJ 150C (5) (10)

ITSM
Peak One Cycle (Sinusoidal) Surge Current (14)

Package Type

Package

Part Number

Amps
MAX 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10

2x10 s
MAX

10x160 s
MAX 100 150 150 150 100 100 100 100 100 100 100 150 150 150 150

Amps 10x560 s
MAX 50 75 75 75 50 50 50 50 50 50 50 100 100 100 100 100

10x1000s
MAX 50 75 75 75 50 50 50 50 50 50 50 100 100 100 100 100

Amps
60Hz 30 30 30 30 30 30 30 30 30 30 30 60 60 60 60 60 50Hz 25 25 25 25 25 25 25 25 25 25 25 50 50 50 50 50

E TYPE 70

P0800EA70 P1100EA70 P1300EA70 P1500EA70 P2300EA70 (12) P2600EA70 (12) P3100EA70 (12) P3500EA70 (12)

B TYPE 70

P2300BA70 (12) P2600BA70 (12) P3100BA70 (12) P3500BA70 (12) P1500EC70 (12)

500

200

General Notes
All measurements are made at 60Hz with a resistive load at an ambient temperature of +25C unless otherwise specified. Storage temperature range (TS) is -65oC to a +150oC. The case temperature (TC) is measured as shown on the dimensional outline drawings. See Package Dimensions section. Junction temperature range (TJ) is -40C to +150C on all devices except for P0300EA70, P0300SA and P0602AA where TJ is -40C to +125C. The maximum Lead solder temperature (for any soldering process) is +230C for 10 seconds maximum: _ > 1/16" (1.59mm) from case. All SIDACtors are Bidirectional and all Electrical Parameters apply to both the forward and reverse polarities. All SIDACtors are recognized under UL 497B Protectors for Data Communications and Fire Alarm Circuits, UL File #E133083. All SIDACtor Leads are Tin/Lead plated with no less than 5% lead content. All SIDACtors meet the surge requirements of the following standards:
CCITT K17 - K20 VDE 0433 10/700 s 5/310 s 10/700 s 5/200 s CNET 0.5/700 s 0.2/310 s 1.5 kV 38 A 2 kV 50 A 1.5 kV 38 A

Electrical Isolation
Teccor's electrically isolated TO-92 and modified TO-220 SIDACtor will withstand a high potential test of 1600 VAC RMS from leads to case over the operating temperature range.

Teccor Electronics, Inc.

Electrical Specifications

IT
Continuous OnState DC or RMS Current (6)(15)

IH
Holding Current (2)

VT
Peak On-State Voltage IT = 1 Amp (17) Off-State Capacitance at 1kHz 1VAC with 50VDC Bias (4)

CO
Off-State Capacitance at 1MHz 15mVAC with 50VDC Bias (4)

di/dt
Critical Rate of Rise of On-State Current

Amps
MAX 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0

mAmps
MIN 50 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150

Volts
MAX 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0

pF
TYP 90 70 70 70 50 45 35 50 40 40 40 50 40 40 40 45

pF
TYP 90 70 70 70 50 45 35 50 40 40 40 50 40 40 40 45

Amps/s
MAX 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100

Applications Guide
See Referenced Device Application Notes for Device Recommendations
Application FCC Part 68 UL 1459 Bellcore TR-NWT-001089 Bellcore TR-NWT-000974 SLIC PTC ISDN T1 Description Connection of Terminal Equipment to the Telephone Network Telephone Equipment Safety Application Note AN1010 AN1011 AN1010 AN1011

Compatibility and Safety for Network TelecommuAN1012 nications Equipment Telecommunications Primary Line Protector Units Call factory for assistance for Central Office and Station Subscriber Line Interface Circuit Using PTCs to Pass FCC Part 68 and UL145 ISDN U & T Interfaces T1 Digital Line Card AN1013 AN1020 AN1025 AN1023

Teccor Electronics, Inc.

Electrical Specifications
VBO IBO
Breakover Current

IPP
Peak Pulse Current TJ 150C (5) (10) Amps 10x160 10x560 s s
MAX 100 150 150 150 150 100 100 100 100 100 100 100 150 150 150 150 500 200 MAX 50 75 75 75 75 50 50 50 50 50 50 50 100 100 100 100 100

ISTM
Peak One Cycle (Sinusoidal) Surge Current (14)

Package Type

Breakover Voltage

Package

Part Number
Volts
MIN P0300SA P0640SA P0641SA (16) P0720SA P0800SA P1100SA P1300SA 27 58 58 65 75 90 120 140 190 220 275 300 190 220 275 300 140 MAX 36 70 70 80 95 125 145 170 265 300 350 400 265 300 350 400 170

Amps
MIN 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10

2x10 s
MAX

10x1000 s
MAX 50 75 75 75 75 50 50 50 50 50 50 50 100 100 100 100 100 60Hz 30 30 30 30 30 30 30 30 30 30 30 30 60 60 60 60 60

Amps
50Hz 25 25 25 25 25 25 25 25 25 25 25 25 50 50 50 50 50

P1500SA P2300SA (11) P2600SA (11) P3100SA (11) P3500SA (11) P2300SB (11) P2600SB (11) P3100SB (11) P3500SB (11) P1500SC (11)

DO-214 Part Numbers and Part Markings


Standardized Part Number
P0300SA P0640SA P0641SA P0720SA P0800SA P1300SA P1500SA P1500SC P2300SA P2300SB P2600SA P2600SB P3100SA P3100SB P3500SA P3500SB

Notes To Electrical Specifications


Symbolized Part Number
P03A P06A P61A P07A P08A P13A P15A P15C P23A P23B P26A P26B P31B P31B P35A P35B

NOTE: On the DO-214 package, Date Code is located below the Symbolized Part Number. TO-92 and TO-220 devices have full part numbers and a Date Code printed on the part.

1. See Figure 4. for VBO change vs. junction temperature. 2. See Figure 2. For IH vs case temperature. 3. All devices have a negative resistance slope unless otherwise noted. Negative resistance slope devices VB0 is measured at an applied rate-of-rise of voltage 1 kV/Sec. See Figure 3A for V-I characteristics. 4. Capacitance imbalance between forward and reverse polarities is typically 15 pF. 5. See Figure 1 (A, B, C) for Pulse Wave Form. 6. Maximum TC is 110C for TO-92 and 115C for modified TO-220, except maximum TC is 75C for P0300SA, P0300EA70 and 95C for P0602AA. 7. During simultaneous surging of pins 1 & 3, the current rating of Pin 2 doubles (2X). 8. Between Pins 2 to 1 and Pins 2 to 3. 9. Between any two pins.

Teccor Electronics, Inc.

Electrical Specifications
IT
Continuous On-State DC or RMS Current (6)(15)

IH
Holding Current (2)

VF
Forward Voltage Drop

VT
Peak On-State Voltage IT = 1 Amp (17) Volts
MAX 5.0 5.0

CO
Off-State Capacitance at 1kHz 1VAC with 50VDC Bias (4) Off-State Capacitance at 15mVAC with 50VDC Bias (4) pF
TYP 90 70 113 70 70 50 45 35 50 40 40 40 50 40 40 40 40

di/dt
Critical Rate of Rise of On-State Current

Amps
MAX 1.0 1.0. 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0

mAmps
MIN 50 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 200

Volts

pF
TYP 90 70 40 70 70 50 45 35 50 40 40 40 50 40 40 40 42

Amps/s
MAX 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100

5.0

5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0

10. The current wave virtual front duration is 1.25X rise time from 10% to 90% of crest. Virtual zero is defined as the intersection with zero axis of a straight line drawn through points on the front of the current wave of 10% and 90% crest. Waveforms defined per IEEE/ANSI C62.1. 11. See Figure 3B for V-I characteristics. 12. 260mA minimum IH is available from the factory on special request. 13.The UL497B rate-of-rise of voltage requirements for VB0 testing is 100V/s, 100V/s, 500V/s, and 1kV/s. All SIDACtors VB0's to be 10% of ratings. 14. For more than one full cycle rating, see Figure 7.

15. Thermal Resistance:


PxxxSA PxxxSB PxxxEA70 PxxxBA70 PxxxAA PxxxAB DO214-AA RJC = 28C/Watt and RJA = 90C/Watt DO214-AA RJC = 26C/Watt and RJA = 85C/Watt TO-92 TO-92 TO-220 TO-220 RJC = 28C/Watt and RJA = 90C/Watt RJC = 26C/Watt and RJA = 85C/Watt RJC = 12C/Watt and RJA = 50C/Watt RJC = 12C/Watt and RJA = 50C/Watt

16. See Figure 3C for V-I characteristics. 17. See Figure 5. 18. See Figure 6.

Teccor Electronics, Inc.

Electrical Specifications

VBO Package Type

IBO

IPP
Peak Pulse Current TJ 150C (5) (10) Amps 10x160 10x560 s s (7) (7)
MAX 100 100 100 100 100 100 100 100 100 100 100 100 100 150 150 150 150 150 150 100 100 100 100 100 100 150 150 150 150 150 150 500 500 200 200 MAX 50 50 50 50 50 50 50 50 50 50 50 50 50 100 100 100 100 100 100 50 50 50 50 50 50 100 100 100 100 100 100 100 100

ITSM
Peak One Cycle (Sinusoidal) Surge Current (14) 10x1000 s (7)
MAX 50 50 50 50 50 50 50 50 50 50 50 50 50 100 100 100 100 100 100 50 50 50 50 50 50 100 100 100 100 100 100 150 150

Package

Part Number

Breakover Voltage Break(Instantaneous Clamping over Voltage) Current (1)(3)(13) Volts PINS 1 to 3
MIN MAX 215 230 250 280 330 360 72 190 250 300 320 580 720 190 250 300 320 580 720 170 240 265 300 350 380 170 340 265 300 350 380 330 350 27 60 95 120 140 220 270 60 95 120 140 220 270 140 180 210 240 280 300 140 180 210 240 280 300 135 280 36 95 125 150 160 290 360 95 125 150 160 290 360 170 240 265 300 350 380 170 240 265 300 350 380 165 350

PINS 3 to 2 1 to 2
MIN MAX

Amps
MAX 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10

2x10 s (7)
MIN

Amps
60Hz 30 30 30 30 30 30 30 30 30 30 30 30 30 60 60 60 60 60 60 30 30 30 30 30 30 60 60 60 60 60 60 60 60 50Hz 25 25 25 25 25 25 25 25 25 25 25 25 25 50 50 50 50 50 50 25 25 25 25 25 25 50 50 50 50 50 50 50 50

P2000AA61

190 205 220 240 270 300 54 120 190 240 280 440 540 120 190 240 280 440 540 140 180 210 240 280 300 140 180 210 240 280 300 270 280

A TYPE 61

P2200AA61 P2400AA61 P2500AA61 P3000AA61 P3300AA61 P0602AA P1602AA P2202AA P2702AA P3002AA P4802AA (11) P6002AA (11) P1602AB P2202AB P2702AB P3002AB P4802AB(11) P6002AB(11)

P1553AA P2103AA P2353AA P2703AA P3203AA P3403AA P1553AB P2103AB P2353AB P2703AB P3203AB P3403AB P3002AC P3202AC

10

Teccor Electronics, Inc.

Electrical Specifications
IT
Continuous OnState DC or RMS Current (6)

IH
Holding Current (2) (9)

VT
Peak On-State Voltage IT =1Amp (18) Volts PINS 3 to 2 1 to 2
MAX

Co
Off-State Capacitance at 1kHz 1VAC with 50 VDC Bias (4) pF PINS 3 to 2 1 to 2 PINS 1 to 3 Off-State Capacitance at 1MHz 15mVAC with 50 VDC Bias (4) pF PINS 3 to 2 1 to 2
TYP 30 30 30 30 25 25 90 140 50 45 40 50 50 140 90 80 75 50 50 50 45 40 35 50 50 100 80 70 60 50 50 45 40 45 85 30 30 25 35 30 85 60 50 45 35 30 40 35 30 25 40 40 80 60 55 50 40 40 30 30 90 140 50 45 40 50 50 140 90 80 75 50 50 50 45 40 35 50 50 100 80 70 60 50 50 45 40

di/dt
Critical Rate of Rise of On-State Current

Amps
MAX 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0

mAmps
MIN 150 150 150 150 150 150 50 150 150 150 150 200 (12) 200 (12) 200 (12) 200 (12) 200 (12) 200 (12) 200 (12) 200 (12) 150 150 150 150 150 150 200 (12) 200 (12) 200 (12) 200 (12) 200 (12) 200 (12) 200 (12) 200 (12)

PINS 1 to 3
MAX 10.0 10.0 10.0 10.0 10.0 10.0

PINS 1 to 3
TYP 30 30 30 30 25 25 45 85 30 30 25 35 30 85 60 50 45 35 30 40 35 30 25 40 40 80 60 55 50 40 40 30 30

Amps/S
MAX 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100

5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 5.0 5.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0

Teccor Electronics, Inc.

11

Electrical Specifications
Figure 1A - Pulse Wave Form (10 x 1000s) Figure 1B - Pulse Wave Form (10 x 560s)

Figure 1C - Pulse Wave Form (10 x 160s)

Figure 2 - Normalized DC holding Current vs Case Temperature

Figure 3A - V-I Characteristics of Devices with Negative Resistance

Figure 3B - V-I Characteristics of Devices with Positive Switching Slopes

12

Teccor Electronics, Inc.

Electrical Specifications
Figure 3C - V-I Characteristics of devices with a Forward Diode and Reverse Negative Resistance Figure 4 - Normalized VBO Change vs Junction Temperature

Figure 5 - Peak On-State Voltage vs Peak On-State Current for DO-214AA and TO-92 (Typical)

Figure 6 - Peak On-State Voltage vs Peak On-State Current for Modified T0-220, Pins 1 to 3 (Typical)

Figure 7 - Peak Surge On-State Current vs Surge Current Duration

Teccor Electronics, Inc.

13

Electrical Specifications

14

Teccor Electronics, Inc.

S-ar putea să vă placă și