Documente Academic
Documente Profesional
Documente Cultură
Alcatel GSM
OEM Product Engineering
SPP-61
Specification for EVOLIUM A9100 Multi-standard Base station Outdoor Evolution Site Preparation
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 1/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
Contents
Preface.................................................................................................. 3 1. Customer or Operator Services ..................................................... 6 2. Alcatel Services ............................................................................... 8 3. General specifications of product ............................................... 10 4. Site preparation and supply requirements for Customer or Operator ............................................................................................. 27 5. Installation and supply requirements for Alcatel ....................... 37 Appendix A: Installation help, cabling site configuration with MBO2 Evolution cabinet with plinth, concrete foundation on field, 3 sectors, 2 antennas / sector, tower. .................................... 39 Appendix B: Installation help, cabling site configuration with MBO2 Evolution cabinet w/o plinth, EBCO cabinet, steel construction on roof, 3 sectors, 2 antennas / sector. .................... 41 Appendix C: Installation help, cabling site configuration with MBO2 Evolution cabinet w/o plinth, back close to wall. ................ 43 Appendix D: Drilling template (without plinth) ............................... 44 Appendix E: Drilling template (with plinth) ..................................... 45 Appendix F: Plinth fixing points....................................................... 46 Appendix G: MBOxE Cabinet fixing points. .................................... 47 Appendix H: External Battery Cabinet Outdoor, general view. ..... 48 Appendix I: External Battery Cabinet Outdoor, fixing points. ....... 49 Abbreviations..................................................................................... 50
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 2/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
Preface
Purpose
The document defines the conditions regarding site preparation, for installing EVOLIUM MBS Outdoor Evolution, and activities to be handled by Customers and Alcatel Services .
EVOLIUM MBS Outdoor Evolution range is designed to ensure an outstanding quality of service through very high radio performances and minimum service interruption, and to facilitate all kinds of evolutions: Site extension or sectorization, implementation of future features. In addition, special attention was focused on ease of deployment and maintenance. The use of highly integrated modules and state-of-the-art components results in very high compactness and reliability. EVOLIUM MBS Outdoor Evolution supports as well GSM and UMTS system. EVOLIUM MBS Outdoor Evolution product range includes multistandard configurations (GSM and UMTS within the same cabinet). Ease of deployment and site interventions: Outdoor cabinets principle allows an easy site installation.
In addition to its main features, the MBS Outdoor can transmit alarms to the OMC-R: - 3 alarm inputs for external functions outside the cabinet. - Other alarm inputs are dedicated to alarms collected inside the cabinet. The alarm inputs 1-16 are pre-wired (mains failure, battery, door, key switch, water detector, smoke detector, heat exchanger). The alarms inputs 17-24 can be used for optional equipments.
Handover of site
For documents relating to site handover before installation of Alcatel equipment, see SPG-07.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 3/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
History
Date 06/01/31 Edition 01 Comments Released.
Audience
Assumed knowledge
You must have a basic understanding of the following BSS Alcatel operations Site Engineering methods
Related documents
Sigle Title of document Specification of documents relating to site handover before installation of Alcatel equipment SPG-10 Alcatel Service for Site Engineering 8BL 00703 0010 DRZZA Alcatel number 8BL 00703 0006 DRAGA
SPG-07
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 4/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
Document Structure
This section provides a summary of the contents of every chapter. Chapter 1 : Chapter 2 : Chapter 3 : Chapter 4 : Operator Chapter 5 : Installation and supply requirements for Alcatel Customer or Operator Services Alcatel Services General specifications of product Site preparation and supply requirements for the Customer or the
Appendix A : Installation help, cabling site configuration with MBO2 Evolution cabinet with plinth, concrete foundation on field, 3 sectors, 2 antennas/sector, tower. Appendix B : Installation help, cabling site configuration with MBO2 Evolution cabinet w/o plinth, EBCO cabinet, steel construction on roof, 3 sectors, 2 antennas/sector. Appendix C : Installation help, cabling site configuration with MBO2 Evolution cabinet w/o plinth, back close to a wall. Appendix D : Installation help, drilling template (without plinth). Appendix E : Installation help, drilling template (with plinth). Appendix F : Plinth fixing points. Appendix G : MBOxE cabinet fixing points. Appendix H : External Battery Cabinet Outdoor, general view. Appendix I : External Battery Cabinet Outdoor, fixing points. Abbreviations : Acronyms encountered within the document.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 5/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 1: Customer or Operator Services
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 6/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 1: Customer or Operator Services
The customer or operator is responsible for choosing the site and for all preparation work. The main services are as follows: Site Preparation of site (refer to SPG-10). Power supply. Earth. PCM links. Feeders. Antennas. Lighting. Circuit breaker . Power distribution box : 230 VAC on 1 or 3 phase(s) / Neutral. Ground bar/plate. Concrete foundation or steel construction. AC power, ground, PCM and alarm cables. Cable way runs from the infrastructure to each MBOE. Cable way runs between MBOE cabinet and battery cabinet. PCM network termination (NTL) upline if necessary. PCM and alarm distributor (DDF). Feeders and antennas.
ALCATEL should be informed about co-located RF emitting equipment in order to prevent its employees against radiation which they cannot influence.
All services not provided by Customer or Operator shall be treated as additional Alcatel services.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 7/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
2. Alcatel Services
This chapter describes the services to be supplied by Alcatel. 2.1 - Services to be performed
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 8/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
Alcatel installs the unit . The main services are listed hereafter:
Basic installation kit with RF jumpers. All lightning protections are integrated inside the MBOE (optional coarse protectors for AC lines are installed externally). Synchronisation cable, (optional) PCM cable from Alcatel equipment to DDF, (optional) Power and ground cables, (optional) Alarm cables, (optional) Installation of MBOE (with or without optional plinth). Installation of External Battery Cabinet Outdoor. Installation of synchronisation cable, (optional) Installation of ground and power cables, (optional) Installation of PCM cable, (optional) Installation of alarm cable, (optional) Commissioning of EVOLIUM MBS Outdoor Evolution. Commissioning of Microwave A9400 (Optional). Acceptance of EVOLIUM MBS Outdoor Evolution.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 9/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 10/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
There are two types of cabinets: MBO1E and MBO2E. MBO1E is a single rack divided in two sections: Left section dedicated to options and/or batteries. This space can be used either by optional equipments only (2 x 5U, 19) like NTL, PDU for TMA or microwave IDU, two 90Ah batteries backup or by mix of optional equipments (5U, 19) and one 90Ah battery backup. Right section dedicated to telecom equipments subracks (TRX, SUMA and ANx) and one subrack for AC/DC converters located in the lower part of the cainet.
MBO2E is composed of the previous MBO1E and of an extension cabinet called MBOEE at the right side. Further space for options (3U/19) is offered at the bottom position inside MBOEE. All external cables enter cabinet in bottom. Each module location within the MBS is driven by engineering rules, easy front cabling, optimisation of thermal dissipation, easy assembly and extensions on site. Each module supports hot insertion and extraction. No service interruption is thus necessary during the most of maintenance interventions.
S S
To increase back-up time, an External Battery Cabinet Outdoor can be optionally used to house up to three battery 90Ah (BU101) strings.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 11/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
The environmental conditions define the climatic requirements (air temperature, humidity, etc.) that apply to the unit in normal operation and storage. They also specify requirements concerning contaminating products and electromagnetic considerations.
ElectroMagnetic All EVOLIUM MBS Outdoor Evolution fulfil the requirements of the Compatibility (EMC) European Directive 89/336/EEC and the harmonized standards: - GSM: EN 301 489-1 and EN 301 489-8 (ETSI) Acoustic noise The acoustic noise caused by the EVOLIUM MBS Outdoor Evolution, measured according to ISO 7779 and ETS 300 019-1-4 complies with ETS 300 753 table B2 Class 4.1E: - lower than 55 dB(A) for daytime operation. - lower than 45 dB(A) for night-time operation. Climatic requirements The environmental conditions define the limits (temperature, humidity, etc.) for MBS Outdoor Evolution cabinets in storage, operation and transportation conditions as specified in the following classes: - For storage ETS 300 019-1-1 class 1.2 - For transportation: ETS 300 019-1-2 class 2.2 - For operation: ETS 300 019-1-4 class 4.1E Earthquake according to ETS 300 019-2-4 Amendment A1 Severity: AG = 5 m/s; ZPA = 15 m/s. Protection level: IP55; IEC 529: Degrees of protection provided by enclosures Safety The EVOLIUM MBS Outdoor Evolution is compliant with following safety standards: Storage of batteries IEC 215 (EN 60215) Product safety of transmitting equipment for telecommunications. IEC 950 (EN 60 950) Safety of information technology equipment. Interpolation is allowed Battery must be charged before storage. Temperature 10 C 20 C 30 C Duration of storage w/o re-charging 1 year 6 months 3 months
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 12/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
Environmental conditions for EVOLIUM MBS outdoor Evolution (ETS 300 019-)
Operation 1-4 class 4.1E Storage -1-1 class 1.2 -25 +55 10 100 0,5 29 no 0,5 70 106 1120 (Note 2) 30 yes yes none Dripping water yes 300 5 20 9 to 200 NA 5 2 to 9 1.5 NA 9 to 200 NA 5
Environmental parameter Low air temperature High air temperature Low relative humidity High relative humidity Low absolute humidity High absolute humidity Rain intensity Rate of change temperature Low air pressure High air pressure Solar radiation (Note1) Heat radiation Movement of surrounding air Conditions of condensation Conditions of precipitation (rain, snow, hail, ...) Low rain temperature Condition of water from sources other than rain Conditions of icing and frosting Sand Dust (suspension) Dust (sedimentation) Stationary vibration, sinusoidal:
Frequency range Peak-displacement amplitude Peak-acceleration amplitude
Unit
C C % % g/m g/m mm/min C/min kPa kPa W/m W/m m/s none none C none none mg/m mg/m mg/(mh) Hz mm m/s
2
-45 +45 8 100 0,03 30 15 0,5 70 106 1120 Negligible 50 yes yes 5 Splashing water yes 300 5 20 2 to 9 1.5 NA
40 --none
40 --5
Note 1: Solar radiation does not impact thermal capability of MBO Evolution. Note 2: Conditions of heat radiation (e.g. in the vicinity of a room-heating system). NA: Not Applicable
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 13/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
Possible AC networks are: TNS, TNC or TT. For TT system external selective differential current breakers are mandatory.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 14/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
MBO1E 1 sector
GSM 900
(8 TRx)
GSM 900
(6 TRx)
GSM 1800
(6 TRx)
Typ.*
Total power (VA) Consumption( Amp.) 1 phase / 3 phases (under 230V / 400V)
2085 9/3
MBO1E 3 sectors
GSM 900
(7 TRx)
GSM 900
(6 TRx)
GSM 1800
(6 TRx)
Typ.*
Total power (VA) Consumption( Amp.) 1 phase / 3 phases (under 230V / 400V)
Nota: Total power value does not include power consumption of service socket: 2300VA (10A/230A)
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 15/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
MBO2E 3 sectors
GSM 900
(12 TRx)
GSM 900
(12 TRx)
GSM 1800
(12 TRx)
Typ.*
Total power (VA) Consumption( Amp.) 1 phase / 3 phases (under 230V / 400V)
MBO2E 6 sectors
GSM 900
(12 TRx)
GSM 900
(12 TRx)
GSM 1800
(12 TRx)
Typ.*
Total power (VA) Consumption( Amp.) 1 phase / 3 phases (under 230V / 400V)
Nota: Total power value does not include power consumption of service socket: 2300VA (10A/230A). (*) Typical power consumption means: - Full traffic load and full Tx power. - Consumption for heat exchanger, 100% - One battery charging (400VA, temporary, see note 1) (**) Operational power consumption means: - Consumption of BCCH, 100% - Consumption of other TRX, 60% - Consumption for heating, 0% Consumption for heat exchanger, 100% Consumption of service socket, 0% One battery charging (5VA, see note 1).
Note1 : 400VA battery charging is only temporary for few hours, after previous full discharge. Real continuous long term operational charging is about 5VA.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 16/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
Products
Battery back-up for MBO Evolution Power Distribution Unit for TMA Microwave A9400UX (IDU 19/1U) Heater
(1)
Power consumption
The above AC power consumption is given with one internal battery back-up (BU101/ 400VA). If MBO Evolution or EBCO contain more than one BU101, add 800VA battery charging instead of 400VA. Add 35VA per PDU (one PDU for 6 TMAs). Add 60 VA per terminal. 1000 VA (1) Consumption = 4A/ 230V
average heating power during MBS operation.In warm-up phase, heating consumption will be: 1000 VA for MBO1E cabinet. 2000 VA (2x1000VA) for MBO2E cabinet. Nota 1: During MBO2E operation, probability that both heaters switch on is low. Here we can consider 50% heating power (2000VA 50% = 1000 VA). Nota 2: Heat exchanger never operates in time with heater.
This may also occur at very low ambient temperature or with reduced traffic at low temperature (-45C above 0C). Therefore, heaters will be foreseen for cold countries.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 17/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
219 / 480 / n.a 195 / 430 / n.a 196 / 430 / n.a 223 / 495 / n.a 173 / 390 / n.a 127 / 285 / 450 107 / 250 / 400 100 / 230 / 365 112 / 260 / 415 90 / 205 / 330 106 / 250 / 400 97 / 225 / 360 87 / 195 / 315 98 / 225 / 360 76 / 175 / 280
The back-up time calculation has been made with the following rule: Consumption of exchanger = 100 % Consumption for socket = 0% Consumption for optional products = 0W
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 18/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
MBO Evolution cabinet total weight (kg) With one battery branch With two battery branches 360 480 520 640
Optional plinth:
Each single cabinet can be optionally mounted on dedicated plinth especially in case of installation on concrete pad: PL1E Width (mm) Depth (mm) Height (mm) Weight (kg) 933 662 150 8 PL2E 619 662 150 6 PL1E+PL2E 1555 662 150 14
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 19/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
MBO Evolution cabinet is intended for installation on a floor structure or on any rigid structure (e.g. concrete plinth or steel frame). The cabinet can be mounted on integral plinth. This optional plinth perform mechanical interface between cabinet and fundament. The cabinet must be fixed to the floor. Four fixing points, one in each corner, are necessary either for fixation to optional plinth (installation on concrete pad) or direct fixation on steel frame. The drilling diameter of holes is 15 mm for metallic structure and 18 mm for concrete foundation. For MBS Outdoor Evolution cabinet, fixing points between axis are: MBO1E version: 500 mm 1 on depth; 902 mm 1 on width. MBO2E version: 500 mm 1 on depth; 1517 mm 1 on width. Shape of holes: Oblong 30x16 mm. For optional plinth, fixing points (to concrete pad) between axis are: MBO1E version: 500 mm 1 on depth; 705 mm 1 on width. MBO2E version: 500 mm 1 on depth; 1327 mm 1 on width. Shape of holes: Oblong 30x16 mm The cabinet has no side doors and its access is only possible from the front side (all internal cabling and equipment accessible only from front side). Cabinet may be installed back to back or back to a wall (clearance conditions must be followed). External cables (PCM, clock, external alarms, antenna cables, AC power cables ... ) enter the cabinet through the bottom. The cabinet is delivered with lifting anchors and in upright position. It can be lifted and carried by means of hoisting lines attached to eye-bolts in edge profiles under the top hood. Sufficient clearance must be allowed for handling, maintenance and inspection procedures, and for equipment cooling purposes.
In particular, in the front of the MBO Evolution, a clearance of approximately 1 m is recommended to allow handling and 1,2 m if there is a high wall limiting air circulation. At left or right side: 100 mm (600 mm on the right side only for mounting and dismantling) (600 mm on cable entry side) At the top: 600 mm (for removing or handling top roof). At the rear: 200 mm.
Reference 8BL 00704 0078 DRZZA Edition 01 Status Released Date 06/01/31 Page 20/50
File A70478a1.doc V85
Alcatel
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
Alarm lightning The 3 alarm inputs for external functions outside the cabinet are lightning protection protected. - Nominal impulse discharge current (wave 8/20s): 2.5 kA. All other alarm inputs are not lightning protected and are dedicated to alarms collected inside the cabinet. - The alarm inputs 1-16 are pre-wired and cannot be used for optional equipments. - The alarm inputs 17-24 can be used for optional equipments. These inputs can withstand a wave 1.2/50s 1500V.
The in-and-outs for antenna cables are under the rack and inside the plinth (cover plates for unused holes): - MBO1E cabinet: 8 x 7/16 antenna female connectors. - MBO2E cabinet : 16 x 7/16 antenna female connectors The in-and-outs for external cables (PCM, clock, external alarms, ... ) are located in bottom left side wall of MBO1E cabinet, and passing through EMC glands. AC power and ground cables are connected to terminal arranged in a box and located in the bottom left side wall of MBO1E cabinet.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 21/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 22/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
PCM lines are: - 120 Ohms: multi pairs from copper line L907 type without connector on MBOE side - 75 Ohms: multi coax from coaxial cable type FLEX3 without connector on MBS Outdoor side.
On DDF side, these cables can be inserted on terminal blocks (120 or 75 Ohms). 120 Ohms: The distance from MBOE to NTL is depending on NTL type, in general with G.703, E1 interface with 40 dB sensitivity the maximal distance is 100 m for L907 using general shield for 4 copper pairs (2TX + 2RX). Diameter of wire: 0,5 mm.
Recommended distance between DDF and MBOE: 20m. Type of cable L907 type: 4 x 4 x 0,5 mm (diameter) 8 coaxs 0,4 / 2,0 / 3,55 FLEX3 type Connection DDF side recommended Inserting Inserting
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 23/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
The cabinet has no side doors and its access is only possible from the front (all internal cabling accessible only from front side). The cabinet has anchor bolt holes at the bottom and must be fixed on the floor. Cabling access is in the cabinet plinth from bottom, back or either side. The cabinet is delivered with eye bolts for lifting and in upright position.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 24/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
Environmental conditions
Climatic requirements: - For operation: ETS 300 019-1-4 class 4.1E. Exceptional max operational temperature for short period (8 hours) up to 50C. - For storage: ETS 300 019-1-1 class 1.2. - For transportation: ETS 300 019-1-2 class 2.2, with batteries fitted. Class 2.3, without batteries fitted. Acoustic noise: The acoustic noise caused by the Battery Cabinet Outdoor, measured according to ISO 7779 and ETS 300 019-1-4 complies with ETS 300 753 table B2 Class 4.1E Electromagnetic compatibility:
- Conducted emission on AC (ACU) and DC (HEX) lines: EN 55022 class B - Surge immunity AC lines: EN 61000-4-5 level 4 - Harmonic current emissions on AC lines: EN 61000-3-2 Safety standard: EN 60950. Ingress protection level: IP55 Clearance Sufficient clearance must be allowed for handling, maintenance, inspection procedures and for equipment cooling. In particular, in the front of the battery cabinet, a clearance of approximately 1 m is recommended (1,2 m if there is a high wall limiting air circulation). At the top: 600 mm Left / right side: 100 mm. Back side: 200 mm Or in all cases 600 mm when cables arrive left/right or back. Maximum cables length between MBOE and EBCO: 10 m. Maximum distance between MBOE and EBCO: 5 m.
External Battery Cabinet is powered with 230VAC (single phase-3 wires) directly from the site AC distribution box to supply airconditioner (ACU) and service light and socket incorporated inside the cabinet. There is no AC connection between MBOE and EBCO. The External Battery Cabinet is connected to MBOE through DC power cables and signalling / alarms cable (remote inventory of battery, ACU fail, door open, smoke detection). AC breakers are fitted in left side wall of cabinet: - 1 x C16A MCB in L line (incoming mains line) - 1 x C10A MCB in L line (ACU) - 1 x 2-pole 6A/30 mA RCD in L an N lines (light/service socket) DC breakers are fitted in 3U distribution pannel at top of cabinet: - 1 x 2 pole 80A MCB fast acting in 0V and 48V main DC lines. - 3 x 1 pole 80A MCB fast acting in minus line of each battery string. - 1 x 2A fuse in 12V line of smoke detector. Note: 0V lead (+ pole of battery) will be connected to PE inside MBOE.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 25/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 3: General specifications of product
Grounding system
The main earthing bolt of the cabinet must be connected to the ground plate available on site. MBOE and battery cabinets must be connected to the same ground plate.
Consumptions indications 230 VAC Air Conditioning Unit (ACU) Heater Service light and socket 500 W 1000 W 1000 W
Lightning protection
Only AC lines are protected. Medium stage protectors for L and N leads.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 26/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 4: Site preparation and supply requirements for Customer or Operator
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 27/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 4: Site preparation and supply requirements for Customer or Operator
The site must be compliant with IEC 364 (NFC 15100) for equipment located only in restricted access locations. On the site, the current safety instructions must be strictly followed and hazardous points must be marked. The inspectors must make sure that signs are posted with the telephone number of emergency medical assistance in the event of electric shock.
Appropriate protection shall be provided to ensure the protection of personnel against all risks of falls and exposure to hazardous voltage sources. An appropriate system of protection shall be provided to protect personnel against the risks associated with high voltage areas: equipotential earth bonding of all handrails and metal obstacles, handrail protection for passageways near the edges of flat roofs.
Displacement of equipment (transport, handling, or hoisting) must not endanger either personnel or equipment near-by. They are several national and international standards and recommendations
dealing about human exposure to ElectroMagnetic Fields. Their main characteristics are very similar for they take account the international recommendations issued by ICNIRP (International Commision on Non Ionizing Radiation Protection). The site must be compliant with ICNIRP guidelines or local regulation if more restrictive. The following rules should be strictly applied by Customer: Compliance RF perimeters related to ElectroMagnetic Field exposure must be marked. Produce clear signalling and marking labels. Minimize RF emission from the antenna. Workers should be allowed to switch-off the power if they have to operate into compliance RF perimeter for workers. Assure good cable connection. Install the antenna as high as possible from floor or area with public access Install the antenna as far as possible from other existing equipment emitting RF power. People with electronic medical devices (for example pace-makers and hearing aids) and pregnant women must identify themselves to site officer.
4.3 - Main supplies See chapter 1: Customer or Operator Services. provided by Customer or operator
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 28/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 4: Site preparation and supply requirements for Customer or Operator
The site shall be handed over with the leased lines in operation. The people in charge to prepare the site (in which the equipment is to be installed) shall provide the site with hoisting and handling devices for delivery of the equipment. If not, the costs incurred by the installer will be added to the installation costs and charged to the client. The equipment can be transported by crane or by people. In the last case, the entrances to the buildings must be large enough to transport the racks in an upright position (minimum height: 2.1 m) and side-by-side (width: 0.8 m). Access to the sites must be facilitated: - either by the presence of a local correspondent during delivery, assembly/wiring, and initial start-up of the equipment - or by obtaining a set of duplicate keys to the sites prior to those operations.
Accessibility
One or two phone lines are needed for the periods of installation and initial startup of the equipments. The floor must be able to bear a load of 600 kg/m2. It must be able to withstand a momentary overload of 250 kg/100 cm and be puncture-resistant to 30 kg/cm2. The floor must be leveled and smooth. Floor evenness must be less: - 3 mm surface evenness under a 1.5 m ruler. - 6 mm slope per meter at any cabinet side. The racks and their extensions are fixed to ground.
Distance Various clearance spaces must be provided for maintenance and inspection operations and to allow equipment ventilation. constraints High voltage The external ports of the equipment (AC mains, PCM links, Ext. Alarms, RF cables) are protected. Lightning protection is recommended for customer AC protector breaker. Lighting and wall sockets The external lamps on site should be of the electronic ballast type. The electronic ballast type is a system without pulses and do not disturb the PCM links.
230 V sockets will be provided inside AC distribution box mainly for emergency and installation purpose (two sockets, 2 poles and ground, 16 A). A portable service light with 230V socket (UTE-CEPEC) is provided inside the cabinet. It is equipped with long spiral cable enough to access MBOEE. The socket is protected by 10A circuit breaker ( total load = 2300VA).
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 29/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 4: Site preparation and supply requirements for Customer or Operator
Cable connections are located under the rack and inside the plinth. Cabling access of Battery Cabinet is only from the bottom. Cables from distribution box to MBS Evolution Outdoor or to Battery Cabinet equipment should not exceed 20 meters. Cables from DDF to MBS Evolution Outdoor equipment should not exceed 20m. The antenna feeders shall have labelled 7/16 feeder connectors. Feeder cables linking MBS Outdoor Evolution to antennas (1 to 2 for each sector) shall be grounded . Distance from feeder termination to MBS Outdoor Evolution connector should be 3 m. Distance from feeder termination to MBS Evolution Outdoor outer side wall sheet should be from 0,3 m to 0,5m. MBS Outdoor Evolution feeder type : LCF Cu2Y: 1/2 , 7/8 , 1 or 1 5/8 Compliant with IEC 754-1/-2. The standard for feeder connector is: IEC 169-4. Feeder losses from MBS Outdoor Evolution antenna connector to antenna input connector, should not exceed 3 dB. For correct operation of MBS Outdoor Evolution, the VSWR should be < 1,5 (or > 14 dB) on feeder termination. Lightning protections are incorporated in the RF connector of the MBS Outdoor Evolution. Microwave A9400 feeder type :ET 390 998 (up to 300m). Diam=10.3mm. Compliant with IEC 332-1. Minimum of decoupling for antennas is 30 dB.
4.5 Cable way The cable way shall be separated or several cable trays shall be installed in requirements order to separate the various electrical supply systems or a space of 30 cm
should be foreseen between two signal types (e.g.: the 230 V should be not adjacent to transmission lines more than 2m). Cables between MBS cabinet and External Battery Cabinet Outdoor must be trunked inside cable tray connected to GND. DC power cables and signal cable may be routed in same track of cable tray. AC mains cable must be routed in separate track of cable tray.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 30/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 4: Site preparation and supply requirements for Customer or Operator
Laptop LMT/IMT provided in option, but necessary during the commissioning. The length of connecting cables between laptop equipment and rack on the site shall not exceed 15 meters. Clearance Length of cables from MBS Outdoor to LMT/IMT terminal Side clearance (only one side is necessary) Front clearance Rear clearance Dimension and weight Width x depth x height (mm) Maximum weight (kg) 100-240V, 50-60 Hz consumption Maximum power consumption (W) Fuse gauges, earth leakage protection 30 mA Gauge (A) 6 200 300x265x45 3 15 m 0.7 m 1m 0.2 m
The customer shall install all cables at the position of rack. Cables shall be installed according to cable manufacturer recommendations.
Ground network TN-S TN-S system without any restrictions (according to ETS 300 253) system - origin of PE at the main earthing terminal of the power source. - PE is intentionally earthed intermediately in the distribution and at each main earthing terminal. - N and PE are separated throughout the distribution, the installation and within each equipment. Ground network TN-C system TN-C system without any restrictions (according ETS 300 253). - the PEN conductor shall be connected to the main earthing terminal only. - from the main earthing terminal to and within the consumer locations inside the building the Neutral conductor (N) shall be treated as a live conductor. - a dedicated PE shall be provided. Ground network TT TT system: An additional external Residual Current operated circuit system Disrupter (RCD) has to be specified (according ETS 300 253). (fault current of the RCD: 100 mA and selective type) - Origin of PE at the local main earthing terminal of the installation. - N and PE are separated throughout the installation and within each equipment.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 31/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 4: Site preparation and supply requirements for Customer or Operator
The MBS Outdoor Evolution is powered with a nominal voltage of 230 V AC under single phase (L, N, PE) or three phases (L1, L2, L3, N, PE). Characteristics of the AC power supply: - Nominal voltage: 230VAC. - Voltage range: 150-280 VAC. - Frequency: 47 to 63 Hz - Impedance of the mains: R < 0.7 Ohm. A power distributing box must be provided as part of the site preparations. It must include marked fuses for each output, and a grounding bus bar for the power cables. The box or power station must be marked.
Power cable Power cables, for MBS and battery cabinet, are with lug connector at the unit end. (AC lug pin 6 mm or 2.5 mm, DC lug pin 25 mm , ground cable diam.= recommended 8mm). Multi strand flexible copper core. Strand composition 0,41 mm max. class 5 (IEC 228) . Standard to be compliant with country legislation. AC power cables: Maximum cable length, condition: Min. AC input voltage : 195 V . 1 cable per MBO Evolution
Signal 230 V Ground(see note1)
* with EMC shielding.
Cross/section
Length max.
5x6 mm * 50 mm / YG
100 m 100 m
3x2.5 mm ** 50 mm / YG
100 m 100 m
DC power cables:
Signal -48VDC 0VDC Ground Cross section Length max EBCO MBO Evolution
Maximum cable length, condition: Min. DC input voltage : 38.4V 25 mm / Blue 25 mm / Black 50 mm / YG 10 m 10 m 10 m
(see note1)
Distribution box The AC distribution should be defined for using tips of system 6 mm or 2.5 recommendations mm for L and N. The AC distribution should be defined for using lugs of system 8 mm for electrical earth.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 32/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 4: Site preparation and supply requirements for Customer or Operator
Breakers The customer provides the following gauges (with lightning protection if recommendations necessary): The gauges should be calculated to operate with ETS 300132-2 standard (195VAC). On first approach, the gauge is calculated like: Imax.+1/3 I max. (I at 195VAC) AC breaker recommended is category C with breaking capacity 6000 A. Selective differential circuit breaker at high leakage current recommended is >100 mA in accordance with the country legislation. It is recommended to dimension the gauge according to the final configuration to avoid an interruption of service during an extension. The gauges must be in line with product safety standards. Cabinet version MBO Evolution (MBO1E/MBO2E) External Battery Cabinet Outdoor Lightning protection for AC lines External breakers recommended: EXTERNAL BREAKERS RECOMMENDED 230 VAC One phase / neutral 230 VAC 3 phases / neutral
C32A
One breaker / curve C per MBS
C25A
One breaker / curve C per phase Not applicable
C25A
One breaker / curve C
Coarse lightning protection Class I, according to IEC 61643-1, is recommended : Single-phase AC lines: minimum capability 35 kA in L, 50 kA in N, pulse 10/350s.
Manufacturer's recommendations should be followed (e.g. distance from adjacent parts, decoupling etc.). Recommended products in respect to coordination with components used inside BTS cabinet: - DEHNvap CSP 100, manufacturer DEHN. Flash Trab Compact, manufacturer Phoenix. A ground plate directly connected to the ground box of the building must be available on site. The grounding system is composed of a metallic grounding network, formed of iron flooring .The grounds are respectively connected to grounding plate, and to the metallic ground of the power distributing box. The ground wire circuit resistance in soil must be less than 10 ohms.
Grounding distribution
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 33/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 4: Site preparation and supply requirements for Customer or Operator
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 34/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 4: Site preparation and supply requirements for Customer or Operator
The equipment terminal block must be apart of customer terminal block (DDF) at maximum 1m. The customer must indicate to Alcatel the connector type on equipment side (only for E1 cables 75 Ohms) and the supplier. The pins of terminal block to wrap (120 Ohms) supplied by the customer must have a diameter between 1 and 1,5 mm.
Optionally, the alarms can be connected directly on connection area of MBOE. The following cables can be used in the case where the customer wants to connect the alarms on the DDF without connector. Alarms Inputs Cable L907 4x2x0,5 mm for 4 alarms Connection on DDF side inserting Nber 1
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 35/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 4: Site preparation and supply requirements for Customer or Operator
The customer shall produce an overall drawing for each MBOE site.
General site information The drawing shall be submitted to Alcatel, after the initial site inspection, or in preliminary project documentation concerning the site requirements supplied by the customer. The drawing shall indicate the position of the MBOE with its connections, relative to a reference point. The drawing shall indicate co-located RF emitting equipment. The site data sheet must be completed based on data provided by the client or during site inspection. The site information procedure document (see document SPG-07) should be completed by the customer or during a site inspection visit with Alcatel. The operator shall hand over to the supplier, with the preliminary study document or on the occasion of the site inspection. A drawing of the distribution frame identifying technical and commercial links with numbers for each link. The links with transmit/receive loops set up on the cable at the unit side. Links qualified as far as the MBOE. The client shall draw up a layout map for each site. That map will indicate the location of: Racks, Power supplies, Air-conditioning system, Cable ways, Collector rod system, Grounding plate, Distribution frames (positioning of the terminal blocks), Furniture for the operating and maintenance tools. Compliance RF perimeters.
Layout
That plan is submitted to the manufacturer, either after an initial inspection of the site or in a preliminary project file for the site provided by the client.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 36/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 5: Installation and supply requirements for Alcatel
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 37/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Chapter 5: Installation and supply requirements for Alcatel
5.1 - Installation
The main services are as follows: The services provided are: Preliminary preparation. Rack installation (with or without plinth) Install lightning protection, power supply, batteries. Power supply and earth cables installation. PCM cables installation.
Antenna jumpers installation. Additional equipments installation (heater, alarm cable, synchronization cable, DC out power cable, water detector, smoke detector). - Finishing installation. and are detailed in EVOLIUM A9100 MBS Evolution Outdoor Installation manual. Commissioning of MBS Evolution Outdoor system Acceptance of MBS Evolution Outdoor system MBS Outdoor powering up and running in accordance with EVOLIUM A9100 MBS Evolution Outdoor Commissioning manual. Customer agrees that MBS Outdoor has been installed, commissioned and is running in accordance with EVOLIUM A9100 MBS Evolution Outdoor Acceptance test manual.
5.2 - Supplies
Alcatel provides: Installation kit to install MBS Evolution Outdoor system. RF jumpers (L: 3m, 7/16 male connectors). Installation kit to install External Battery Cabinet Outdoor. Synchronisation cables. Alarm cable. PCM cables. AC power and ground cables. DDF. Plinth.
Mandatory Optional
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 38/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Appendix A: Installation help, cabling site configuration with MBO2 Evolution cabinet with plinth, concrete foundation on field, 3 sectors, 2 antennas / sector, tower.
Appendix A: Installation help, cabling site configuration with MBO2 Evolution cabinet with plinth, concrete foundation on field, 3 sectors, 2 antennas / sector, tower.
SECTOR 1
Alcatel
SECTOR 3
SECTOR 2
Edition 01
Status Released
Date 06/01/31
Page 39/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Appendix A: Installation help, cabling site configuration with MBO2 Evolution cabinet with plinth, concrete foundation on field, 3 sectors, 2 antennas / sector, tower.
Clearance
100 or 600 mm
800 mm
MBO2 Evolution
1000 mm
600 mm
AN T2
SE CT OR 2
AN T1
SECTOR 1
ANT2
ANT1
T2 AN T1 AN
R TO C SE
Alcatel
Edition 01
Status Released
Clearance
200 mm
Date 06/01/31
1560 mm
Front
Back
Page 40/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Appendix B: Installation help, cabling site configuration with MBO2 Evolution cabinet w/o plinth, EBCO cabinet, steel construction on roof, 3 sectors, 2 antennas / sector.
Appendix B: Installation help, cabling site configuration with MBO2 Evolution cabinet w/o plinth, EBCO cabinet, steel construction on roof, 3 sectors, 2 antennas / sector.
SECTOR 3 ANT 2 SECTOR 2 ANT 2 ANT 1 SECTOR 1
File A70478a1.doc V85
ANT 1
ANT 2
MBO2 Evolution
Reference 8BL 00704 0078 DRZZA
Battery cabinet
ANT 1
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 41/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Appendix B: Installation help, cabling site configuration with MBO2 Evolution cabinet w/o plinth, EBCO cabinet, steel construction on roof, 3 sectors, 2 antennas / sector.
Clearance
SECTOR 1
ANT 2 ANT 1
SECTOR 2
ANT 2
ANT 1
200 mm
Back
100 mm
MBO2 evolution
EBCO
600 mm
100 mm
Clearance
1560 mm 700 mm
Front
Alcatel
Edition 01
Status Released
Date 06/01/31
ANT 1
SECTOR 3
Page 42/50
1m
100 mm
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
ANT 2
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Appendix C: Installation help, cabling site configuration with MBO2 Evolution cabinet w/o plinth, back close to wall.
Appendix C: Installation help, cabling site configuration with MBO2 Evolution cabinet w/o plinth, back close to wall.
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 43/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
SPP-61, EVOLIUM A9100 MBS Outdoor Evolution Appendix D: Drilling template (without plinth).
15
500 mm
FRONT
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 44/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 45/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
662
500 #
PL1E
19
81 #
114 #
705 #
500 #
662
PL1E
PL2E
81 #
114 #
1327#
Alcatel
Edition 01
Status Released
16
Date 06/01/31
Page 46/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
MBO2E to plinth
513
M6 80.2 35.5
28 902 (MBO1E) 28
1517 (MBO2E)
500
44
25
40
Alcatel
Edition 01
Status Released
Clearance area
250
Page 47/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 48/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
15 mm 15 mm
30 mm
640 mm
500 mm
150 mm
100 mm
500 mm
Front of cabinet
Installation note: Fixing with four screws is sufficient. Holes at either side (640 mm x 500 mm) are recommended to allow same IPN as Alcatel BTS Outdoor.
Alcatel
Edition 01
Status Released
30 mm
740 mm
Date 06/01/31
Page 49/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel
Abbreviations
Abbreviations
Sigle Description
AC ACU BSC BTS DC DDF EMF GSM IDU IMT IPN LCF LMT MBOE MBO1E MBO2E MBOEE MBS N NTL ODU PCM PDU PE PEN PL1E PL2E RCD RF SELV TNV TMA TRX UMTS VSWR
Alternative Current AirConditioner Unit Base Station Controller Base Transceiver Station Direct Current Digital Distribution Frame ElectroMagnetic Field. Global System for Mobile communication InDoor Unit for transmission connection (Microwave) Interface Maintenance Terminal. Metallic part streamlined in I Low Loss Cellflex cable Local Maintenance Terminal Multistandard BTS Outdoor Evolution Multistandard BTS Outdoor Evolution cabinet 1 door Multistandard BTS Outdoor Evolution cabinet 2 doors Multistandard BTS Outdoor Evolution cabinet Extension part 1 door Multistandard Base Station Neutral Network Termination Line OutDoor Unit Pulse Code Modulation Power Distribution Unit Protective Earth Combined Protective Earth and Neutral Plinth 1 for MBO1E Plinth 2 for MBOEE Residual Current operated circuit Disrupter Radio Frequency Safety Extra Low Voltage Telecom Network Voltage Tower Mounting Amplifier Transmitter and Receiver unit Universal Mobile Telecommunications System. Voltage Standing Wave Ratio (Return loss)
END OF DOCUMENT
Alcatel
Edition 01
Status Released
Date 06/01/31
Page 50/50
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel