Documente Academic
Documente Profesional
Documente Cultură
Toolmakers clamps, unlike many workshop items, have very little room for deviating from their required mode of use. For example, you can run your lathe, too fast or too slow, with the cutting tool well below centre or even above centre at large diameters and still produce reasonable results. However, only a very small deviation from the perfect setting for a toolmakers clamp and you will have an inadequate clamping action and, depending on the task in hand, a potentially dangerous one. Used correctly though, their clamping action will be the equal of, and often superior to, most other clamps. This depending of course on them being used only for applications that they are suitable for.
This clamp is extremely useful for holding work together when drilling, tapping and other machining operations. Manufactured from case hardened steel for strength. Equipped with a spring clip and a retaining ring which holds the loose jaw in place when the clamp is being adjusted. Size 70 mm / 2.3/4in capacity
Made from Hardened Steel. Clamp equipped with Spring screw Clip. Highly useful for holding small work together when drilling, welding, assembling etc. Clamps include spring clip and retaining ring. Shine black finish.
Item Code No ABM VC- 4826 ABM VC- 4827 ABM VC- 4828 ABM VC- 4829 ABM VC- 4830 ABM VC- 4831 ABM VC- 4832
Jaw Length 2 2 3 4 5 6 8
Parallel clamp is designed for maximum strength and rigidity. It is extremely useful for holding work together in tapping and drilling and on various machine setups. The ends of the jaws are rounded to permit clamping under shoulders or in recesses. A retaining ring holds the loose jaw in alignment when the clamp is being opened or closed. Clamps is made of steel, nicely finished and hardened.
Consisting of two metal jaws which are opened and closed by two screws at right angles to the length of the jaws.
Useful for holding small work together when drilling Useful for holding objects whilst gluing Shiny, black finish Ends of jaws chamfered
LENGTH OF JAWS 38mm 50mm 75mm 100mm 125mm 150mm 200mm 250mm 300mm
OPENING OF JAWS 17mm 25mm 40mm 65mm 90mm 125mm 150mm 200mm 250mm
Features Hardened and Tempered jaws Clamps equipped with spring screw clip Highly useful for holding small work together, when drilling, welding, assembling etc.
Cat. No
Jaw Opening Inch 1-1/4 1-3/4 2-1/4 2-3/4 3-1/2 4-1/2 6 mm 31 44 57 70 89 114 150
TMPC - 340 TMPC - 340 TMPC - 340 TMPC 340 TMPC 340 TMPC 340 TMPC - 340
2 2 3 4 5 6 8
1" Toolmaker's Clamps Industrial Quality Up for bid is a set of four one inch toolmaker's clamps. These are quality items, made in the USA, and weigh about 8.2 ounces each. They will secure a part that is up to 1" high, and the finger reaches up to-1" from its mounting post. Each clamp consists of the following parts:
4-1/4" X 1-1/2" A beaverboard workpad 1/8" thick, measuring 2" X 1-1/2" A steel finger 3" long, 1/2" X 1/2" square Necessary screws and nuts ready to -assemble. ;
These handy clamps can be used for various modelmaking tasks, including the following:
press
Holding sheets of brass for soldering Clamping sheets of plastic for gluing Repairing brass imported models
Many other uses! Toolmakers clamps Steel, case hardened, Ends of Jaws for clamping under shoulder or in recess. Clip holds loose jaw in chamfered position when claps screw is released, a convenient and original Brown & Sharpe feature.