Documente Academic
Documente Profesional
Documente Cultură
1. Blade is an angle formed by a line perpendicular to the propeller shaft and line formed by the (a) Relative wind (b) Apparent wind (c) Chord of the blade (d) Blade face 2. Thrust produced by a rotating propeller is a result of (a) Propeller slippage (b) An area of low pressure behind the propeller (c) An area of decreased pressure immediately in front of the pressure blades (d) The angle of relative wind and rotational velocity wind and rotational velocity of the propeller 3. Propeller blade station number increase from (a) Huh to tip (b) Tip to hule (c) Leading edge to aft edge (d) Aft edge of leading edge 4. It should have high specific gravity (a) Low pan point 5. Velocity index should be high. High freezing point at a cold atm the water contents in the fuel in having tendency to form in a ice crystal 6. It should be filtered to jet engine (a) It should have low carbon content after burning the fuel 7. In twin spool engine, with constant N2, compressor inlet temperature is decreasing then (a) N2 changes (b) Fuel flow increases (c) N1 decreases (d) The ratio N1 is maintained constant N2 8. The thrust developed by high bypass ratio engine is (a) Indicated by EGT (b) Indicated by N2 (c) Proportional fan speed (d) Not affected by ambient conditions
9. Perceived noise decibel (PNDB) level is low in case of (a) Pure jets without noise suppressor (b) Straight jet with noise suppressor (c) Low by pass jets (d) High by pass jets with acoustic panel 10. Ignitor plug spark is due to
1|Page
www.rjworld.com
11. In a hot tank oil system (a) Oil cooler is not provided (b) Oil is stored in a separate tank (c) Oil is at high temp in the tank (d) De-aerator effect is very slow 12. If jet velocity and mass flow is constant for a jet engine then thrust (a) Is maximum when aircraft speed is minimum (b) Is maximum when aircraft speed is maximum (c) Is more when jet velocity and inlet velocity are equal (d) Is always constant 13. Water injection systems are provides for the jet engine for the thrust augmentation the thrust augmentation for water injection can be caused and by two methods. (a) By adding or injecting water at the compressor inlet (b) By adding or injecting water at the differ section Fig shown that a water tank made up of aluminum or sheet metal allows the water flow a regulating It then panes to the pressure regulating V/o of the diffuse and compressor inlet thought which water injection in done by providing two manifolds at the diffuse and compressor manifold. A water heater is provided for the water to not formed ice in cold atm or cold weather condition A drain a/v provided to drain full water tank after are it is generally use of after getting sufficient thrust by water injection Water injection system used when aircraft an going to take off
14. In a compressor space between surge line and working lines called (a) Safety margin on surge margin (b) Stable zone unstable zone (c) Unstable zone (d) Stagger zone 15. Hottest zone in turbine engine is (a) Compressor outlet (b) Turbine (c) 1st stage NGV (d) Exhaust nozzle 16. In a high by pass engine NGVs are eliminated (a) To reduced noise (b) To reduce weight
2|Page
www.rjworld.com
20. Jet engine ignition system. Jet engine ignition system is a high intensity and dual capacitor discharge type are used The two system are used for the ignition system (a) Low voltage A.C or D.C type ignition system (b) High voltage capacitor discharge type ignition system 21. High voltage capacitor discharge type ignition system FIGURE SHOWN HIGH VOLTAGE CAPACITOR DISHCARGE TYPE CUT (A.G) A 115 A.C is provided bu E.S.I. but to the primary coil of the transformer A to reduce the noise level a filter cut is provided at the primary After paning 115V at the primary a seen way coil induces a voltage of about 2000V approximately which paner through solid rectifier A through resistance to the dual capacitor or storage capacitor which store the electrically charger In the next cycle a 20000 is paned through rectifier B this resistance 22. Combustion chamber used in a modern jet engines are (a) Can annular type (b) Annular type (c) Can type (d) As stated in 1 and 2
3|Page
www.rjworld.com
4|Page
www.rjworld.com
5|Page
www.rjworld.com
Get more previous year DGCA question papers and AME study material at www.rjworld.com or visit http://aviation.rjworld.com .
6|Page
www.rjworld.com