Documente Academic
Documente Profesional
Documente Cultură
1.2 Power Supply: a) Power Source Range.........................................................................99VAC to 242VAC. b) Power Supply: automatic commutation. c) Power Consumption: Model CR14300......................................................................................................60W; Model CR20300......................................................................................................72W; Model CR20310......................................................................................................80W; Model CR29411....................................................................................................130W; STAND BY..................................................................2W (120VAC) and 3W (220VAC).
d) High Voltage (Fly back Anode Voltage) and beam current: High Voltage: CR14300/20300....................................................................22 1.5 KV; Beam current - with brightness and contrast at the maximum...................0.7 + 0.1 mA; CR20310...............................................................................23 + 1.5 KV; Beam current - with brightness and contrast at the maximum...................0.9 + 0.1 mA; CR29411............................................................................27.5 + 1.5 KV; Beam current - with brightness and contrast at the maximum...................1.4 + 0.1 mA;
e) Heating:..............................................................................................6.15 + 0.15 Vrms. f) FLY BACK Main Power Supply : Fly back Output Voltage CR14300.....................105 2 V DC; max ripple 2 Vpp; Fly back Output Voltage CR20300 e CR20310....108.5 2V DC; max ripple 2 Vpp; Fly back Output Voltage CR29411..................130 2V DC.; max ripple 2 Vpp.
1.3 Tuner and Receiving channel: Channel Coverage............................. 181 channels VHF/UHF/cable. Color System: .........................................................PAL-N , PAL-M and NTSC;
1.6 Carrier System: Audio...................................................................................................................4.5Mhz; PAL-M Chrome........................................................................................3,575.611Mhz; NTSC Chrome..........................................................................................3,579.545Mhz; PAL-N Chrome.........................................................................................3,582.056Mhz.
1.7 Speaker Output: CR14300/20300....................................................................2.5W rms; CR20310...................................................................2.5W + 2.5W rms; CR29411.........................................................................5W + 5W rms.
1.9 Terminals: Rear and front audio (mono) and video input ..................................CR14300/20300; Rear and front audio (stereo) and video input ...............................................CR20310; Two rear and one front audio (stereo) and video input...................................CR29411; Input minimum impedance....................................................................10kOhms; Audio input signal level................................................................400 to 800mVrms; Video input signal level.....................................................................................1Vpp. Rear Audio output .. ....................................CR29411 and CR20310; Output maximum impedance......................................................................1kOhms; Variable output level (maximum volume)....................................................1.5Vrms;
1.10 Dimensions (WxDxH): CR14300...........................................................................................358.5x383x349 mm; CR20300..............................................................................................486x488x446 mm; CR20310..............................................................................................486x488x446 mm; CR29411..............................................................................................754x529x578 mm.
2. DISASSEMBLY INSTRUCTIONS Removal of mechanical parts and P.C. boards. 2.1 Back cabinet (refer to fig. 2.1) a. Remove the screws which are used for holding the back cabinet to the front cabinet (6 screws for 14 models, 8 screws for 20 and 29 models). b. Remove the screws which are used for holding the rear A/V input and output connectors. c. Remove the back cabinet. 2.2 CRT PCB (refer to fig. 2.2/2.3) CAUTION: Before removing the anode cap, discharge electricity because it contains high voltage. Before attempting to remove or repair any PCB, unplug the power cord from the AC source. a. Remove the anode cap. b. Disconnect the ground connector (CM801). c. Remove the CRT PC board. 2.3 Main PCB (refer to fig. 2.2/2.3) a. Disconnect the following connectors: CM901, CM902, CM701, CM601, CM401 and CM402 b. Unlock the PCB from the cabinet (both side of the board). c. Remove the main PCB. 2.4 CRT (refer to fig. 2.4) a. Remove the 4 screws. b. Remove the CRT. Note: REMOVAL OF ANODE CAP After turning the power off there might still be a potential voltage that is very dangerous. When removing the ANODE CAP, make sure to discharge the anode caps potential voltage. Do not use pliers to loosen or tighten the anode cap terminal, this may cause the spring to be damaged.
To exit the service mode, press MENU button and turn off the TV set.
14
SERVICE HP HB HSH VS VA
SERVICE WG WB Yn Yp Yav
SERVICE ORIGMAG
VO.3P
15
Apply a color bar pattern (RF Input) with 500V signal; Connect a DC Voltmeter, in the AGC pin of the tuner; Adjust AGCT to Zero and measure the voltage (V1); Adjust AGCT so that the indication on the voltmeter be (V1) - 1 0.2V.
ILLUSTRATION 2
16
Activate the adjustment mode display (SBL item). Ajust SBL from 0 to 1. Blanking the bottom of the screen. Adjust VSH until the bottom of the pattern be aligned with the reference marks of the mechanical center on picture tube (the central vertical line in the center of the tube). Adjust VS until the central line be aligned with the half bottom of the screen (the central line of the circle pattern in the half cut of the screen) Return SBL from 1 to 0 value . The image could be compressed or expanded. Select VA item and set its value to adjust the size of the picture (proportional height and width picture). If necessary readjust SC item and set its value to adjust the Linearity (acts in the top of the image) and VA.
NOTE: The SC and VA adjustments are interdependent (they should be used together). When the image to be decentralized in the vertical, to retouch VSH and/or VS
After the image menu preset, turn off the television and activate the service menu. Select ORIGMAG item;
17
Press VOLUME + button and change the value from 0 to 1 . Turn off the television and the ORIGINAL MAGIC setup will be registered.
18
NOTE:
Consult the original r. c. manufacturer documentation to access the schematic diagram and the replacement parts list.
MAIN MENU PICTURE SOUND CHANNEL TUNING SETUP > > > > >
19
4 REMOTE CONTROL
Model CR29411
NOTE:
Consult the original r. c. manufacturer documentation to access the schematic diagram and the replacement parts list.
MAIN MENU PICTURE SOUND CHANNEL TUNING SETUP > > > > >
20
22
23
24
25
26
6 DESCRIPTION OF THE FUNCTIONS THE INTEGRATED CIRCUITS PINS 6.1 IC101 (TDA9380)
SIGN OPEN SCL DAS GAME SWITCHES A SWITCHES B VSH DET DET SAP GND SW 0 SW 1 GND A SEC PLL VP 2 DEC D05 PH2IF PH1IF GND 3 DET BG AVL EWD VDR B VDR A IF IN 1 IF IN 2 L REF VC CAP AGC DEEM/SIFIN1 SDEC SIF 2 GND2 SNDPLL SIF AGC AVL REF HOUT SAND ALDEXT OSS AM EHT PROT PLLIF VIDEOOUT SUPLY CVBS GND1 SVHS Y SVHS CROMA AUDOUT INS SW2 ERVIN G2/YIN B2UIN PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 DESCRIPTION N/C SERIAL CLOCK OUTPUT SERIAL DATA OUTPUT GAME (PWM) SWITCHES OF THE FRONT PANEL (IN) SWITCHES OF THE FRONT PANEL AND LED INDICATION (IN) SVHS DETECTING (IN) SAP DETECTING (IN) TERRA COMMUTATION TO EXTERNAL AV COMMUTATION TO EXTERNAL AV GROUND PLL DECOUPLING (SECAM) SUPPLY 2 DECOUPLING OF THE DIGITAL PROCESSOR FILTER 2 FILTER OF SYNCHRONISM GROUND 3 FILTER OF (BANDGAP) AVC FILTER TO VERTICAL OUTPUT B TO VERTICAL OUTPUT A IF SIGNAL INPUT FILTER S.A.W IF SIGNAL INPUT FILTER S.A.W CURRENT INPUT REF. V. DRIVE DECOUPLING OF VERTICAL FILTER OF AGC SIF 1 INPUT DECOUPLING OF UDIO (IN 2) GROUND 2 FILTER OF AGC AND SIF N/C OUTPUT OF HORIZONTAL OSC. 15750HZ H PULSE SAND CASTLE EXTERNAL AUDIO INPUT IN THE MOD CR14300/20300 IN THE OTHERS: N/C PROTECTION PLL IF FILTER VIDEO OUTPUT SUPPLY INPUT OF VIDEO PACKAGE GROUND SVHS VIDEO INPUT SVHS CHROME VIDEO INPUT AUDIO OUTPUT RGB GROUND R-Y GROUND G-Y GROUND B-Y GROUND 27
BCORR/VGUARD BLYIN R G B VDD A VPE VDD C OSDGND XIN XOUT RESET VDD P MUDO PW ON IR
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
ABL
BEAM CURRENT
RED R GREEN G BLUE B SUPPLY GROUND SUPPLY GND OF OSC 12MHZ CRISTAL OF 12MHZ CRISTAL OF 12MHZ RESET CIRCUIT SUPPLY 33V MUTE POWER IR INPUT
TW TS CW CS VEO VEI CNR CM CDEC GND SDA1 SCL VCC COMP VCAP CP1 CP2 CPH CADJ CER CMO CSS LOR SOR AVR LIR CPS2 CPS1 EOR VIR LDR OUTR NC SW B2R B1R TR
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
CAPACITOR TIMING WIDEBAND FOR DBX CAPACITOR TIMING SPECTRAL FOR DBX CAPACITOR WIDEBAND FOR DBX CAPACITOR SPECTRAL FOR DBX VARIABLE EMPHASIS OUTPUT FOR DBX VARIABLE EMPHASIS INPUT FOR DBX CAPACITOR NOISE REDUCTION FOR DBX CAPACITOR MUTE FOR SAP CAPACITOR DC-DECOUPLING FOR SAP GROUND SERIAL DATA INPUT/OUTPUT (I2C-BUS) SERIAL CLOCK INPUT (I2C-BUS) SUPPLY VOLTAGE COMPOSITE INPUT SIGNAL CAPACITOR FOR ELECTRONIC FILTERING OF SUPPLY CAPACITOR FOR PILOT DETECTOR CAPACITOR FOR PILOT DETECTOR CAPACITOR FOR PHASE DETECTOR CAPACITOR FOR PILTER ADJUSTMENT CERAMIC RESONATOR ( 503KHz) CAPACITOR DC-DECOUPLING MONO CAPACITOR DC-DECOUPLING STEREO/SAP OUTPUT LINE CONTROL, RIGHT CHANNEL OUTPUT SELECTOR, RIGHT CHANNEL INPUT AUTOMATIC VOLUME CONTROL, RIGHT CHANNEL INPUT LINE CONTROL, RIGHT CHANNEL CAPACITOR 2 PSEUDO FUNCTION CAPACITOR 1 PSEUDO FUNCTION OUTPUT EFFECTS, RIGHT CHANNEL INPUT VOLUME CONTROL, RIGHT CHANNEL INPUT LOUDNESS, RIGHT CHANNEL OUTPUT, RIGHT CHANNEL NOT CONNECTED FILTER CAPACITOR FOR SUBWOOFER BASS CONTROL CAPACITOR, RIGHT CHANNEL BASS CONTROL CAPACITOR, RIGHT CHANNEL TREBLE CONTROL CAPACITOR
13 14 15 16
OUTPUT AV3 ( L) INPUT TO CR29411 AND VIDEO INPUT TO CR14300/20300 AV1 ( L) INPUT TO CR20310/29411 - AUDIO INPUT TO CR14300/20300 SUPPLY VOLTAGE
30
7.0 - OPERATION DESCRIPTION TELEVISION SET CIRCUIT Fig.1- Block diagram 3.Tuner 2. TV signal processor and Microprocessor Circuit 4. AV switches 5. Stereo decoder 6.Audio output
Speaker
7.Video output
1. Power Supply
The block diagram in Fig.1 shows how the TV set circuit works divided into 8 basic circuits. 7.1 - POWER SUPPLY IC901, IC902, IC903, T901, Q901 and surrounding components (9xx) This is a switching mode power supply designed to operate in AC power source from 99 Volts to 242 Volts and 50/60 Hertz. The main device is the TDA16846 (controller for switching mode power supplies). There are two different operating modes, low power standby and full operation mode. -Standby: The power supply works in the burst mode and the circuit turn-on during 2 ms and turn-off during 12 ms. In this mode the power consumption is less than 2 Watts in 120 V AC and less than 3 Watts in 220 V AC. In the burst mode, the output voltages are reduced to 10% of the normal values (except microprocessor supply voltage) . -Full operation mode: This mode is activate by the microprocessor (Remote control or front panel). The output voltages regulation is controlled by the IC903 circuit, opto coupler feedback (IC902) and by the IC901. The basic output voltages are: 1. 108/128 Volts (CR14300_20300/CR20310_29411) to horizontal circuit; 2. +12 and 12 Volts to audio and vertical circuits; 3. 9 Volts to TV signal processor, stereo decoder and AV circuits; 4. 5 Volts to microprocessor and memory circuits; 5. 3.3 Volts to microprocessor and front panel switches circuits. There are 3 basic protection mode: 1. AC power source undervoltage: the power supply will turn-off when the AC source is less than 95 Volts. 2. Power consumption limit: when the power consumption exceed 20% of the normal value. 3. Overvoltage outputs shutdown: when the output voltages exceed 15% of the normal values. 7.2 - TV SIGNAL PROCESSOR + MICROPROCESSOR IC101, IC102 and surrounding components (1xx) The main device is the TDA9380 (TV signal processor-Teletext decoder with embedded Micro-Controller) that combines the functions of a TV signal processor together with a Micro Controller and Closed Caption decoder. The highlights of this device are:
31
-Enhanced 80C51 microprocessor core; -Internal program memory (48 Kbytes ROM and 1 Kbytes RAM); -High performance OSD; -Closed Caption decoder; -I2C bus serial I/O; -Only one reference (12 MHz) crystal for all internal timing; -Multi-standard vision IF circuit (45.75 MHz) with PLL demodulator; -PAL/NTSC color decoder with automatic search system; -Integrated luminance and chrominance circuit; -RGB control circuit; -8V and 3.3V supply voltages; -Horizontal and vertical geometry processing. An external E2PROM (IC102) with 4 Kb is used to keep the setup and calibration configuration by I2C bus (channels, volume, horizontal and vertical geometry, etc.). Front panel buttons and IR decoders are also realized by IC101. 7.3 - TUNER TU201, SF201 and surrounding components (2xx). This is a standard Frequency Synthesizer Tuner (FST Tuner) which covers VHF and UHF channels, including cable channels (frequency range from 55.25 MHz to 801.25 MHz). This device is controlled by I2C bus. The output signal (IF output) is connected to the IC101 through a SAW filter (SF201). 7.4 - AV SWITCHES Q330, Q331, Q340, Q351, Q341, Q350, IC490 and surrounding components. The external audio and video signals (AV1, AV2, AV3) are selected by the Micro Controller using two output signals (SW0_pin10 and SW1_pin11 IC101). The video signals are selected using standard transistors and the audio signals are selected using the IC490 (4052) The selected video signal is connected to the TV signal processor external video input and the selected audio signal is connected to the TV signal processor (mono models) or to the stereo decoder (stereo models). 7.5 - STEREO DECODER IC450, Q450, Q450R and surrounding components. This circuit is used only in stereo models and the main device is TDA9855 (stereo decoder). Using I2C bus, the IC101 can identify a stereo and SAP signals. This device combines stereo decoder and audio processor. In stereo models, this device offers automatic volume level control, special effects, volume control, bass control and treble control. 7.6 - AUDIO OUTPUT IC401, Q401, SP401, SP401R and surrounding components. The main device is TDA7499 (stereo amplifier). The output signal is a 3+3 Watts with a 16 ohms speakers. The input signals come from the stereo decoders or from the TV signal processor (mono models). This circuit uses external mute system (Q401) to minimize speaker noise during turn on/off. 7.7 - VIDEO OUTPUT Q810, Q811, Q820, Q821, Q830, Q831 and surrounding components. The RGB signals from micro controller are amplified to the CRT using a standard transistors configuration.
32
7.8 - HORIZONTAL AND VERTICAL DEFLECTIONS IC601, T701, T702, Q701 and surrounding components. Vertical deflection circuit uses a TDA9309 (IC601 - vertical deflection booster) and operates with around 24V and provides output current to drive the yoke. The input signals are vertical drive A and B from the TV signal processor (VDRA_pin22 and VDRB_pin21 IC101). Horizontal deflection circuit uses 15.7KHz signal (HOUT_pin33 IC101) to drive the fly back transformer (T701) and provides the output current to drive horizontal deflection coil (yoke) and others CTR voltages (HV, focus, screen and etc.). The vertical deflection circuit has one protection mode (turn-off the power supply if a fault situation is detected) and the horizontal deflection circuit has two protection modes: -turn-off the power supply if a HV over voltage is detected (X-ray protection); -turn-off the power supply if a horizontal drive transistor (Q701) overstress is detected.
33
Without sound
Models CR20310/29411
Check IC101 C404
No
IC101 pin 43
Signal. OK ?
Yes
Models CR14300/20300
No
C404 R445/430
No
No Yes Yes
Yes Q430 C440/431R432 No IC 490 pin 14 Signal. OK ? Yes IC 490 pin 13 signal. OK ? Yes IC101 C409 No IC101 pin 43 Signal. OK ? Yes
Check R453 and R454 Replace IC 450 Check IC450 pin 29 signal . Check IC 410 and around components.
No IC490 or VCC No
Yes
34
START
Yes
No
No
Yes
No
Yes
Check C714 C715 Ok ?
Replace T701
No
Q701 Ok ?
Yes
No
replace
Yes
No
Check: flyback
Yes
Check: flyback
No
horizontal Yoke E. H. T. Ok ?
Yes
Check: Yoke
35
Start
No
Stand by
Yes
No
Is F901 open?
No
Check : TH901
Yes
Yes
Check: TH901, IC901 and Q901
No
No
Yes
Yes
Replace IC 901
36
TV doesnt TUNE IN
No
Yes
No
Yes
Replace tuner
37
TV DOESNT TURN ON
No
Yes
No
Yes
No
Check:
D912 gate pin (9V). OK ?
Yes
Check: D912
38
WITHOUT SAP
No
Yes
No
Yes
No
Yes
No
Yes
Check or replace IC490/R120/R109
No
Yes
Check or replace C409 / IC101
39
Vertical closed
No
Yes
No
Yoke Connected ?
Yes
No
No
Yes
Check or replace IC101
Yes
No
Check: IC601 Ok ?
Yes
40
IC101
No
Yes
No
Check: C301
Yes
Check:
AV external video Signal. OK ?
No
Yes
Check: IC101
No
Fix the fault
41
9 WAVEFORMS
IC101 pin 22
one chip
0.78Vpp
5 s 42
IC101 pin 40
0.6Vpp
20
IC101 pin 38
one chip
1.5VPP
20 s
IC101 pin 34
one chip
5.7 Vpp
20 s
43
100Vpp
20
10Vpp
20 s
4.5 Vpp
20 s
3.8Vpp
20 s
44
4.5Vpp
20 s
98Vpp
20 s
98Vpp
20 s
98Vpp
20 s
45
* MODEL's DIFERENCES
POS/MOD CR14300 CR20300 CR20310 ST
*
TO R403 TO C450 FOR STEREO MODEL TO C405R FOR MONO MODELS MONO MODELS
* R815/815A R835/835A
AUDIO OUTPUT
LIVE
COLD
AV1 REAR
AV2 FRONT
SCHEMATIC DIAGRAM
CR14300/20300/20310 STEREO
DE-155-001-012
11/JUL/2001
01 DE 01
65