Documente Academic
Documente Profesional
Documente Cultură
Features
Low Input Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75V Max. Input Bias Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15pA Superb Temperature Drift - Voltage Offset. . . . . . . . . . . . . . . . . . . . . . . 0.65V/C Max. - Input Current. . . . . . . . . . . . . . . . . . . . . . . . . .0.9pA/C Max. Outstanding ESD Performance - Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5kV - Machine Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500V - Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . .1.5kV Very Low Voltage Noise, 10Hz . . . . . . . . . . . . . . . . . 14nV/Hz Low Current Consumption (per amp) . . . . . . . . 0.29mA Max. Gain-bandwidth Product . . . . . . . . . . . . . . . . . . . . . . . . . . 1MHz Wide Supply Range . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 40V Operating Temperature Range. . . . . . . . . . .-40C to +125C No Phase Reversal Pb-Free (RoHS Compliant)
Applications
Precision Instruments Medical Instrumentation Spectral Analysis Equipment Active Filter Blocks Microphone Pre-amplifier Thermocouples and RTD Reference Buffers Data Acquisition Power Supply Control
Related Literature
See AN1508 ISL281X7SOICEVAL1Z Evaluation Board Users Guide See AN1509 ISL282X7SOICEVAL2Z Evaluation Board Users Guide
1000 V+ = 19V AV = 1
100
10 0.1
10
100
1k
10k
100k
FREQUENCY (Hz)
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2009-2012. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners.
16
15
- +
+IN_B
4 5
NC
VOUT_B
VOUT_C
-IN_B
- +
+IN_C
Circuit 3 Circuit 1
Circuit 3 Circuit 2
V+ OUT VCIRCUIT 2
VCIRCUIT 1
Characterization vs Simulation Results. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Package Outline Drawing (M8.15E). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Package Outline Drawing (M8.118B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Package Outline Drawing (L8.3x3K) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Package Outline Drawing (L16.4x4E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Package Outline Drawing (MDP0027). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Package Outline Drawing (MDP0044). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Thermal Information
Thermal Resistance (Typical) JA (C/W) JC (C/W) 8 Ld SOIC (ISL28107, Notes 4, 5). . . . . . . . 120 60 8 Ld SOIC (ISL28207, Notes 4, 5) . . . . . . . 105 50 8 Ld MSOP (ISL28107, Notes 4, 5) . . . . . . 155 50 8 Ld MSOP (ISL28207, Notes 4, 5) . . . . . . 160 55 8 Ld TDFN (ISL28107, Notes 6, 7) . . . . . . . 44 3 8 Ld TDFN (ISL28207, Notes 6, 7) . . . . . . 43 2 14 Ld SOIC (ISL28407, Notes 4, 5) . . . . . . 73 45 14 Ld TSSOP (ISL28407 Notes 4, 5) . . . . . 90 32 16 Ld QFN (ISL28407, Notes 6, 7) . . . . . . . 42 3.5 Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65C to +150C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Ambient Operating Temperature Range . . . . . . . . . . . . . .-40C to +125C Maximum Operating Junction Temperature . . . . . . . . . . . . . . . . . .+150C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 5. For JC, the case temp location is taken at the package top center. 6. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with direct attach features. See Tech Brief TB379. 7. For JC, the case temp location is the center of the exposed metal pad on the package underside.
Electrical Specifications VS 15V, VCM = 0, VO = 0V, RL = Open, TA= +25C, unless otherwise noted. Boldface limits apply over the
operating temperature range, -40C to +125C. PARAMETER VOS DESCRIPTION Offset Voltage Magnitude; SOIC Package CONDITIONS ISL28107, ISL28207 MIN (Note 8) -75 -140 ISL28407 -90 -160 Offset Voltage Magnitude; MSOP Package ISL28107 -100 -180 ISL28207 -110 -200 Offset Voltage Magnitude; TDFN Package ISL28107 -100 -190 ISL28207 -100 -175 TCVOS Offset Voltage Drift; SOIC Package ISL28107, ISL28207 ISL28407 Offset Voltage Drift; MSOP Package Offset Voltage Drift; TDFN Package ISL28107 ISL28207 ISL28107 ISL28207 -0.65 -0.8 -0.85 -0.9 -0.9 -0.75 0.1 0.2 0.1 0.1 0.1 0.1 10 10 5 5 10 TYP 5 MAX (Note 8) 75 140 90 160 100 180 110 200 100 190 100 175 0.65 0.8 0.85 0.9 0.9 0.75 UNIT V V V V V V V V V V V V V/C V/C V/C V/C V/C V/C
AC SPECIFICATIONS
GBW enp-p en en en en in THD + N Gain Bandwidth Product Voltage Noise Voltage Noise Density Voltage Noise Density Voltage Noise Density Voltage Noise Density Current Noise Density 0.1Hz to 10Hz, VS = 19V f = 10Hz, VS = 19V f = 100Hz, VS = 19V f = 1kHz, VS = 19V f = 10kHz, VS = 19V f = 10kHz, VS = 19V 1 340 14 13 13 13 53 0.0035 MHz nVP-P nV/Hz nV/Hz nV/Hz nV/Hz fA/Hz %
TRANSIENT RESPONSE
SR tr, tf, Small Signal Slew Rate Rise Time 10% to 90% of VOUT Fall Time 90% to 10% of VOUT ts Settling Time to 0.1% 10V Step; 10% to VOUT Settling Time to 0.01% 10V Step; 10% to VOUT tOL Output Overload Recovery Time AV = 10, RL = 10k, VO = 10VP-P AV = 1, VOUT = 100mVP-P, Rf = 0, RL = 2k to VCM AV = 1, VOUT = 100mVP-P, Rf = 0, RL = 2k to VCM AV = -1 VOUT = 10VP-P, Rg = Rf = 10k, RL = 2k to VCM AV = -1, VOUT = 10VP-P, Rg = Rf =10k, RL = 2k to VCM AV = 100, VIN = 0.2V, RL = 2k to VCM 0.32 355 365 29 31.2 6 V/s ns ns s s s
Electrical Specifications VS 5V, VCM = 0, VO = 0V, TA = +25C, unless otherwise noted. Boldface limits apply over the operating
temperature range, -40C to +125C. PARAMETER VOS DESCRIPTION Offset Voltage Magnitude; SOIC Package CONDITIONS ISL28107, ISL28207 MIN (Note 8) -75 -140 ISL28407 -90 -160 Offset Voltage Magnitude; MSOP Package ISL28107 -100 -180 ISL28207 -110 -200 Offset Voltage Magnitude; TDFN Package ISL28107 -100 -190 ISL28207 -100 -175 10 10 5 5 10 TYP 5 MAX (Note 8) 75 140 90 160 100 180 110 200 100 190 100 175 UNIT V V V V V V V V V V V V
Offset Voltage Drift; SOIC Package ISL28107, ISL28207 ISL28407 Offset Voltage Drift; MSOP Package ISL28107 ISL28207
Offset Voltage Drift; TDFN Package ISL28107 ISL28207 IB Input Bias Current ISL28107, ISL28207 Input Bias Current ISL28407 TA = -40C to +85C TA = -40C to +125C TA = 0C to +70C TA = -40C to +85C TA = -40C to +125C TCIB Input Bias Current Drift ISL28107, ISL28207 TA = -40C to +85C TA = -40C to +85C; ISL28207 MSOP Package Only TA = -40C to +125C Input Bias Current Drift ISL28407 TA = 0C to +70C TA = -40C to +85C TA = -40C to +125C IOS Input Offset Current ISL28107, ISL28207 Input Offset Current ISL28407 TA = -40C to +85C TA = -40C to +125C TA = 0C to +70C TA = -40C to +85C TA = -40C to +125C TCIOS Input Offset Current Drift ISL28107, ISL28207 TA = -40C to +85C TA = -40C to +125C TA = -40C to +85C; ISL28207 MSOP Package Only Input Offset Current Drift ISL28407 TA = 0C to +70C TA = -40C to +85C TA = -40C to +125C VCM CMRR PSRR AVOL VOH Common Mode Input Voltage Range Common-Mode Rejection Ratio Power Supply Rejection Ratio Open-Loop Gain Output Voltage High Guaranteed by CMRR test VCM = -3V to +3V VS = 2.25V to 5V VO = -3V to +3V, RL = 10k to ground RL = 10k to ground -40C to +125C RL = 2k to ground -40C to +125C
AC SPECIFICATIONS
GBW THD + N Gain Bandwidth Product Total Harmonic Distortion + Noise 1kHz, G = 1, VO = 2.5VRMS, RL = 2k 1 0.0053 MHz %
TRANSIENT RESPONSE
SR tr, tf, Small Signal Slew Rate Rise Time 10% to 90% of VOUT Fall Time 90% to 10% of VOUT ts Settling Time to 0.1% 4V Step; 10% to VOUT Settling Time to 0.01% 4V Step; 10% to VOUT NOTES: 8. Parameters with MIN and/or MAX limits are 100% tested at +25C, unless otherwise specified. Temperature limits established by characterization and are not production tested. 9. Output Short Circuit Current is the minimum current (source or sink) when the output is driven into the supply rails with RL = 0 to ground. AV = 10, RL = 2k AV = 1, VOUT = 100mVP-P, Rf = 0, RL = 2k to VCM AV = 1, VOUT = 100mVP-P, Rf = 0, RL = 2k to VCM AV = -1, VOUT = 4VP-P, Rf = Rg = 2k, RL = 2k to VCM AV = -1, VOUT = 4VP-P, Rf = Rg = 2k, RL = 2k to VCM 0.32 355 370 12.4 22 V/s ns ns s s
10
50 TEMPERATURE (C)
100
150
50 TEMPERATURE (C)
100
150
1400 VS = 15V NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS 1200 1000 800 600 400 200 0 -100 -80 -60 -40 -20 0 20 VOS (V) 40 60 80 100
1400 VS = 5V 1200 1000 800 600 400 200 0 -100 -80 -60 -40 -20 0 20 VOS (V) 40 60 80 100
16 VS = 15V NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS 14 12 10 8 6 4 2 0 -0.45 -0.30 -0.15 0 0.15 TCVOS (V/C) 0.30 0.45
11
-100
-100
-200 -50
-25
25
50
75
100
125
150
-200 -50
-25
TEMPERATURE (C)
25 50 75 TEMPERATURE (C)
100
125
150
80 VS = 15V NUMBER OF AMPLIFIERS 60 50 40 30 20 10 0 -1.8 -1.4 -1.0 -0.6 -0.2 0.2 TCIb+ (pA/C) 0.6 1.0 NUMBER OF AMPLIFIERS 70
VS = 5V
1.0
200 Vs = 5V 100
-100
-100
-200 -50
-25
25 50 75 TEMPERATURE (C)
100
125
150
-200 -50
-25
25 50 75 TEMPERATURE (C)
100
125
150
12
VS = 5V
200 VS = 15V 150 100 IOS (pA) IOS (pA) 50 0 -50 -100 -150 -200 -50 0 50 TEMPERATURE (C) 100 150
200 VS = 5V 150 100 50 0 -50 -100 -150 -200 -50 0 50 TEMPERATURE (C) 100 150
50 45 NUMBER OF AMPLIFIERS 40 35 30 25 20 15 10 5 0 -0.7 -0.5 -0.3 -0.1 0.1 0.3 TCIOS (pA/C) 0.5 0.7 VS = 15V NUMBER OF AMPLIFIERS
50 45 40 35 30 25 20 15 10 5 0 -0.7 -0.5 -0.3 -0.1 0.1 0.3 TCIOS (pA/C) 0.5 0.7 VS = 5V
13
CMRR (dB)
PSRR (dB)
160
140
140 120
120 -50
50 TEMPERATURE (C)
100
150
100 -50
150
63000 VO = 13V 53000 43000 33000 23000 13000 3000 -50 VOH (V)
Vs = 15V RL = 10k
AVOL (V/mV)
50 TEMPERATURE (C)
100
150
50 TEMPERATURE (C)
100
150
VS = 15V RL = 10k
14.4 14.2 14.0 VOH (V) 13.8 13.6 13.4 13.2 -50
VS = 15V RL = 2k
VOL (V)
150
150
14
150
50 TEMPERATURE (C)
100
150
VS = 5V RL = 10k
0.40 0.35 15V 0.30 IS (mA) 2.25V 0.25 0.20 0.15 0.10 -50
50 TEMPERATURE (C)
100
150
50 TEMPERATURE (C)
100
150
60 ISC+ @ 15V 55 50 ISC+ (mA) ISC- (mA) 45 40 35 30 25 20 -50 0 50 TEMPERATURE (C) 100 150
15
100
10 0.1
10
100
1k
10k
100k
FREQUENCY (Hz)
0.1
0.01 0.1
10
100
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
VS = 2.25V, 5V, 15V 10k 100k 1M 10M 100M -60 -15 -10 -5 0 5 10 15
FREQUENCY (Hz)
FIGURE 38. INPUT OFFSET VOLTAGE vs INPUT COMMON MODE VOLTAGE, VS = 15V
16
200 180 160 140 PHASE 120 100 80 60 40 20 GAIN 0 -20 R = 10k L -40 CL = 10pF -60 SIMULATION -80 -100 0.1m 1m 10m 100m 1 10 100 1k 10k 100k 1M 10M 100M FREQUENCY (Hz)
AV = 1000
8 6 4 2 0 -2 -4 V+ = 5V -6 RL = 10k CL = 4pF -8 AV = +2 -10 VOUT = 10mVP-P -12 1k 10k Rf = Rg = 100 Rf = Rg = 1k Rf = Rg = 100k Rf = Rg = 10k
AV = 100
-20 10
100k
1M
10M
1M
10M
FREQUENCY (Hz)
1 0 NORMALIZED GAIN (dB) -1 -2 -3 -4 -5 -6 -7 -8 -9 V+ = 5V CL = 4pF AV = +1 VOUT = 10mVP-P 1k 10k 100k FREQUENCY (Hz) 1M 10M RL = 100k RL = 10k RL = 1k RL = 499 NORMALIZED GAIN (dB)
1M
10M
17
1M
10M
2 0 NORMALIZED GAIN (dB) -2 -4 -6 -8 -10 C = 4pF L -12 RL = 10k AV = +1 -14 VOUT = 100mVP-P -16 1k 10k VS = 20V VS = 5V VS = 15V VS = 2.25V 100k FREQUENCY (Hz) 1M 10M CROSSTALK (dB)
140 120 100 80 60 RL = 10k 40 C = 4pF L AV = +1 20 VOUT = 1VP-P 0 10 100 VS = 5V VS = 15V 1k 10k 100k FREQUENCY (Hz) 1M 10M
2.5 2.0 1.5 LARGE SIGNAL (V) 1.0 0.5 0 -0.5 -1.0 -1.5 -2.0 0 50 100 150 200 TIME (s) 250 300 350 400 -2.5 0 5 10 CL = 4pF AV = 1 VOUT = 4VP-P 15 20 25 30 35 VS = 5V, 15V, RL = 2k VS = 5V, 15V, RL = 10k
TIME (s)
18
0.06 0.02 -0.02 INPUT (V) -0.06 -0.10 -0.14 -0.18 -0.22 -0.26 0 20 40
OUTPUT
1 -1 INPUT OVERSHOOT (%) -3 OUTPUT (V) -5 -7 VS = 15V RL = 10k CL = 4pF AV = 100 Rf = 10k, Rg = 100 VIN = 200mVP-P -9 -11 -13
RS VE
HO
OT
HO RS VE
OT
60
Applications Information
Functional Description
The ISL28107, ISL28207 and ISL28407 are single, dual and quad, very low 1/f noise (14nV/Hz @ 10Hz) precision op-amps. These amplifiers feature very high open loop gain (50kV/mV) for excellent CMRR (145dB) and gain accuracy. Both devices are fabricated in a new precision 40V complementary bipolar DI process. The super-beta NPN input stage with bias current cancellation provides bipolar-like levels of AC performance, with the low input bias currents approaching JFET levels. The temperature stabilization provided by bias current cancellation removes the high input bias current temperature coefficient commonly found in JFET amplifiers. Figures 9 and 10 show the input bias current variation over temperature. The input offset voltage (VOS) has a very low, worst case value of 75V max at +25C and a maximum TC of 0.65V/C. Figure 38 shows VOS as a function of supply voltage and temperature with the common mode voltage at 0V for split supply operation. 19
The complementary bipolar output stage maintains stability driving large capacitive loads (to 10nF) without external compensation. The small signal overshoot vs. load capacitance is shown in Figure 54.
(EQ. 2)
where: TMAX = Maximum ambient temperature JA = Thermal resistance of the package PDMAX = Maximum power dissipation of one amplifier VS = Total supply voltage IqMAX = Maximum quiescent supply current of one amplifier VOUTMAX = Maximum output voltage swing of the application RL = Load resistance
Unused Channels
If the application only requires one channel, the user must configure the unused channels to prevent them from oscillating. The unused channels can oscillate if the input and output pins are floating. This results in higher than expected supply currents and possible noise injection into the channel being used. The proper way to prevent this oscillation is to short the output to the inverting input and ground the positive input, as shown in Figure 55.
License Statement
+
Power Dissipation
It is possible to exceed the +150C maximum junction temperatures under certain load and power supply conditions. It is therefore important to calculate the maximum junction temperature (TJMAX) for all applications to determine if power supply voltages, load conditions, or package type need to be modified to remain in the safe operating area. These parameters are related using Equation 1:
T JMAX = T MAX + JA xPD MAXTOTAL (EQ. 1)
The information in this SPICE model is protected under the United States copyright laws. Intersil Corporation hereby grants users of this macro-model hereto referred to as Licensee, a nonexclusive, nontransferable licence to use this model as long as the Licensee abides by the terms of this agreement. Before using this macro-model, the Licensee should read this license. If the Licensee does not accept these terms, permission to use the model is not granted. The Licensee may not sell, loan, rent, or license the macro-model, in whole, in part, or in modified form, to anyone outside the Licensees company. The Licensee may modify the macro-model to suit his/her specific applications, and the Licensee may make copies of this macro-model for use within their company only. This macro-model is provided AS IS, WHERE IS, AND WITH NO WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED, INCLUDING BUY NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. In no event will Intersil be liable for special, collateral, incidental, or consequential damages in connection with or arising out of the use of this macro-model. Intersil reserves the right to make changes to the product and the macro-model without prior notice.
where: PDMAXTOTAL is the sum of the maximum power dissipation of each amplifier in the package (PDMAX)
20
VIN-
VinV5 24 D12 DN + + -
VIN+
Voltage Noise
V++ G1 4 + 5 Vc R6 1 V2 1.86V R8 + + 14 V4 1.86V 2.55E10 10 D2 DX + V1 - 1.86V 11 G3 R5 1 + 13 D4 DX + V3 - 1.86V Vg
Input Stage
V++ G5 R7 2.55E10 C2 6.25pF R9 1 + Vc 17 R11 1 Vg R12 1 18 + L2 1.59E-3 V-L1 1.59E-3
Vmid
Vmid
G2 + + 12 -
G4
C3 6.25pF
R10 1
G6
V-VCM
D3 DX
D5 DX
VCM
V++ D8 DX 22 ISY 0.21mA D6 DX 20 23 D9 DX V5 + + 1.12V D7 VDX V6 21 1.12V G8 + D10 DY + G9 + G10 + R16 90 VOUT G7 R15 90 VOUT
V+
V+ + + E2
Vg
V--
Output Stage
21
E3
V-
D11 DY
22
100
100
10 0.1
10 100m
1.0
FREQUENCY (Hz)
10k
100k
70 60 50 40 GAIN (dB) 30 20 10 0 -10 -20 10 AV = 10 Rg = 10k, Rf = 100k AV = 1 Rg = OPEN, Rf = 0 AV = 100 AV = 1000 Rg = 100, Rf = 100k Rg = 1k, Rf = 100k V+ = 20V CL = 4pF RL = 10k VOUT = 100mVP-P
70 60
AV = 1000
AV = 100
40
GAIN (dB) AV = 10
20
Rg = 10k, Rf = 100k AV = 1 Rg = OPEN, Rf = 0
-20
100 1k 10k 100k FREQUENCY (Hz) 1M 10M
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
1 0 NORMALIZED GAIN (dB) -1 -2 -3 -4 -5 -6 -7 -8 -9 V+ = 20V CL = 4pF AV = +1 VOUT = 100mVP-P 1k 10k RL = 100k RL = 10k RL = 1k RL = 499 NORMALIZED GAIN (dB)
1 0 RL = 100k RL = 1k -2 RL = 10k -4 V+ = 15V -6 CL = 4pF AV = +1 VOUT = 100mVP-P 10k 100k FREQUENCY (Hz) 1M 10M RL = 499
23
50
100
150
300
350
400
50
100
200
250
300
200 180 160 140 PHASE 120 100 80 60 40 20 GAIN 0 -20 R = 10k L -40 CL = 10pF -60 SIMULATION -80 -100 0.1m 1m 10m 100m 1 10 100 1k 10k 100k 1M 10M 100M FREQUENCY (Hz)
GAIN
-50 1m 10m
1M
100M
150
CMRR (dB)
100
50 SIMULATION 0 1m
100m
10
10M
100M
24
FN6631.4 On page 2, Pin Configurations, added ISL28207 MSOP pin diagram. On page 3, Pin Descriptions, added ISL28207 MSOP to pin descriptions. On page 4, Ordering Information, added ISL28207FUZ part and information. Updated ISL28107FBZ Pkg Dwg # from M8.118 to M8.118B. For ISL28107FRTZ and ISL28207FRTZ, updated Pkg Dwg # from L8.3x3A to L8.3x3K. For "Coming Soon" parts: ISL28407FBZ: changed Pkg Dwg # from M14.15 to MDP0027; ISL28407FVZ: changed Pkg Dwg # from M14.173 to MDP0044; ISL28407FRZ: changed Pkg Dwg # from 16.4x4 to L16.4x4E. ISL28207FRTZ: changed Part Marking from 207Z to 8207. For "Coming Soon" parts: ISL28407FBZ: changed Part Marking from 28407 to 28407 FBZ. ISL28407FVZ: changed Part Marking from 28407 to 28407 FVZ. ISL28407FRZ: changed Part Marking from 28407 to 407FRZ. Added "Coming Soon" ISL28407SOICEVAL1Z Evaluation Board. On page 6, Thermal Information, added ISL28207 8Ld MSOP, and ISL28407 14 Ld SOIC and 16 Ld QFN thermal information. On page 6 and page 8, Electrical Specifications: for VOS spec for ISL28207 MSOP package, added -110V MIN, +110 V MAX, and -200V MIN, +200V MAX. For TCVOS spec for ISL28207 MSOP package, added -0.9V/C MIN, +0.9V/C MAX. On page 8 and page 8, Electrical Specifications: for TCIB spec for ISL28207 MSOP package, added -1.5pA/C MIN, +1.5pA/C MAX. For TCIOS spec for ISL28207 MSOP package, added -1.5pA/C MIN, +1.5pA/C MAX. Updated to current Intersil datasheet template.
25
conditions (since only MIN/MAX specs with TA = -40C to +125C conditions should be bolded, per note in common conditions)
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a complete list of Intersil product families. For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on intersil.com: ISL28107, ISL28207 and ISL28407. To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff FITs are available from our website at: http://rel.intersil.com/reports/sear
26
6.0 0.20 3.90 0.10 4 PIN NO.1 ID MARK 5 (0.35) x 45 1.27 0.43 0.076 0.25 M C A B 4 4
1.75 MAX
1.45 0.1 0.25 0.175 0.075 GAUGE PLANE C SEATING PLANE 0.10 C
SIDE VIEW A
0.63 0.23
DETAIL "A"
(1.27) (0.60)
NOTES: (1.50) 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. Unless otherwise specified, tolerance : Decimal 0.05 Dimension does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed 0.25mm per side. 5. 6. The pin #1 identifier may be either a mold or mark feature. Reference to JEDEC MS-012.
2. (5.40) 3. 4.
27
DETAIL "X"
0.15 - 0.05mm
0.10 0.05mm
33
NOTES: 1. Dimensions are in millimeters. 2. Dimensioning and tolerancing conform to JEDEC MO-187-AA and AMSEY14.5m-1994. 3. Plastic or metal protrusions of 0.15mm max per side are not included. 4. Plastic interlead protrusions of 0.15mm max per side are not included. 5. Dimensions are measured at Datum Plane "H". 6. Dimensions in ( ) are for reference only.
28
SEE DETAIL "X" C 0.10 C 0.75 0.05 C 0.08 C SIDE VIEW 0 . 02 NOM. 0 . 05 MAX. DETAIL "X" 0 . 203 REF 5
( 2.30) ( 1.95)
NOTES: ( 8X 0.50) (1.50) 2. ( 2.90 ) 3. 4. PIN 1 (6x 0.65) 6. ( 8 X 0.25) TYPICAL RECOMMENDED LAND PATTERN 7. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. Compliant to JEDEC MO-229 WEEC-2 except for the foot length. Unless otherwise specified, tolerance : Decimal 0.05 Dimension applies to the metallized terminal and is measured between 0.15mm and 0.20mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
29
12
4.00
2 . 50 0 . 05
(4X)
TOP VIEW
16X 0 . 4 0 . 05
BOTTOM VIEW
0.90.1
BASE PLANE
SEATING PLANE 0.08 C
SIDE VIEW
C ( 16X 0 .30 ) ( 16 X 0 . 6 )
0 . 2 REF
0 . 00 MIN. 0 . 05 MAX.
DETAIL "X"
NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal 0.05 4. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature.
30
1 B
(N/2) L1
SEATING PLANE L 4 4
0.010
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SYMBOL A A1 A2 b c D E E1 e L L1 h N NOTES: 1. Plastic or metal protrusions of 0.006 maximum per side are not included. 2. Plastic interlead protrusions of 0.010 maximum per side are not included. 3. Dimensions D and E1 are measured at Datum Plane H. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 SO-8 0.068 0.006 0.057 0.017 0.009 0.193 0.236 0.154 0.050 0.025 0.041 0.013 8 SO-14 0.068 0.006 0.057 0.017 0.009 0.341 0.236 0.154 0.050 0.025 0.041 0.013 14 SO16 (0.150) 0.068 0.006 0.057 0.017 0.009 0.390 0.236 0.154 0.050 0.025 0.041 0.013 16 SO16 (0.300) (SOL-16) 0.104 0.007 0.092 0.017 0.011 0.406 0.406 0.295 0.050 0.030 0.056 0.020 16 SO20 (SOL-20) 0.104 0.007 0.092 0.017 0.011 0.504 0.406 0.295 0.050 0.030 0.056 0.020 20 SO24 (SOL-24) 0.104 0.007 0.092 0.017 0.011 0.606 0.406 0.295 0.050 0.030 0.056 0.020 24 SO28 (SOL-28) 0.104 0.007 0.092 0.017 0.011 0.704 0.406 0.295 0.050 0.030 0.056 0.020 28 TOLERANCE MAX 0.003 0.002 0.003 0.001 0.004 0.008 0.004 Basic 0.009 Basic Reference Reference NOTES 1, 3 2, 3 Rev. M 2/07
31
MDP0044
THIN SHRINK SMALL OUTLINE PACKAGE FAMILY MILLIMETERS SYMBOL 14 LD 16 LD 20 LD 24 LD 28 LD TOLERANCE
PIN #1 I.D.
A A1 A2
1.20 0.10 0.90 0.25 0.15 5.00 6.40 4.40 0.65 0.60 1.00
1.20 0.10 0.90 0.25 0.15 5.00 6.40 4.40 0.65 0.60 1.00
1.20 0.10 0.90 0.25 0.15 6.50 6.40 4.40 0.65 0.60 1.00
1.20 0.10 0.90 0.25 0.15 7.80 6.40 4.40 0.65 0.60 1.00
1.20 0.10 0.90 0.25 0.15 9.70 6.40 4.40 0.65 0.60 1.00
Max 0.05 0.05 +0.05/-0.06 +0.05/-0.06 0.10 Basic 0.10 Basic 0.15 Reference Rev. F 2/07
E1
1 B TOP VIEW
(N/2)
b c D E E1
C SEATING PLANE
0.05
e
H
L L1 NOTES:
0.10 M C A B
1. Dimension D does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15mm per side. 2. Dimension E1 does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm per side. 3. Dimensions D and E1 are measured at dAtum Plane H. 4. Dimensioning and tolerancing per ASME Y14.5M-1994.
SEE DETAIL X
END VIEW
L1
For additional products, see www.intersil.com/product_tree Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com
32