Documente Academic
Documente Profesional
Documente Cultură
www.argtek.com
Fax :+ 886-2-2999-7742
Front Panel
LED
Description Router power on. Wireless LAN is active. Wireless LAN is disabled. Wireless LAN is sending or receiving data. WAN is connected and active. WAN is disconnected or inactive. WAN port is sending or receiving data. Wired LAN port(s) is connected and active. Wired LAN port(s) is disconnected or inactive. Wired LAN port(s) is sending or receiving data.
www.argtek.com
Fax :+ 886-2-2999-7742
Rear Panel
Item DC-Jack WAN Port LAN Port USB Port Reset Button Antenna Connector
Description Power connector, connect to power adapter. Wide Area Network port, for connecting Cable Modem or ADSL modem. Local Area Network port. Connect your network devices including computers, printers, game consoles, hubs, or switches. Connect your 3G USB modem. Reset router to manufacture default configurations or start WPS function. RP-SMA connector for connecting antenna.
Network Setup
www.argtek.com
Fax :+ 886-2-2999-7742
provides two types of Internet connection: wireless(3G/3.5G USB modem) or wired (xDSL / cable modem) connection. You can access internet via USB 3G/3.5G modem card, or via wired xDSL / cable modem connection. However, only one connection can be used at the same time. You will need to configure your network for the very first time and whenever you want to change configurations via web interface. To make the network configurations, you have to connect computer to one of the LAN port and open your web browser. The AP Router is delivered with the following factory default parameters on the Ethernet LAN interfaces.
Default IP Address: 10.10.10.254 Default IP subnet mask: 255.255.255.0 Web login User Name: admin Web login Password: admin
The device has two operation modes (Gateway/Bridge). The default IP addresses for the device are 10.10.10.254, so you need to make sure the IP address of your PC is in the same subnet as the device, such as 10.10.10.X. It will take about 55 seconds to complete the boot up sequence after power on. You can refer to user manual for the details of how to configure your network.
www.argtek.com
Fax :+ 886-2-2999-7742
www.argtek.com
Fax :+ 886-2-2999-7742
2a. In Internet Settings / WAN /, select PPPoE (ADSL) for your WAN Connection Type and enter your User Name & Password which were presented by your ISOP company. And then press Apply
2b. In Internet Setting/LAN/, you may change the setting of IP address, DHCP and etc. then press Apply
3. In Wireless Settings / Basic, you may change the setting of SSID, and then press Apply
www.argtek.com
Fax :+ 886-2-2999-7742
4. In Wireless Settings / Security, you may change the setting of password, and then press Apply
Finish setting and press Apply, the setting will be completed after rebooting around 20 seconds.
Note: You have to connect ADSL cable with WAN port of this equipment. ==============================================================
www.argtek.com
Fax :+ 886-2-2999-7742
1. In Operation Mode, please select Bridge. Select AP or Main AP in Wireless Operation Mode and press Apply
www.argtek.com
Fax :+ 886-2-2999-7742
2. In Internet Setting/LAN/, you may change the setting of IP address, DHCP and etc. then press Apply
3. In Wireless Settings / Basic, you may change the setting of SSID, and then press Apply
4. In Wireless Settings / Security, you may change the setting of password, and then press Apply
Finish setting and press Apply, the setting will be completed after rebooting around 20 seconds. Note: You have to connect cable line with LAN port of this equipment
www.argtek.com
Fax :+ 886-2-2999-7742
2 Open the IE ( Internet Explorer) and type 10.10.10.254 on Website to enter the setup frame. If you cant enter to setup frame, you can try to set the IP address for 10.10.10.XXX and try to connect again. Otherwise, please press Reset button around 10 seconds to restore AP and try to enter again Select the Operation Mode on the left side of setup frame
www.argtek.com
Fax :+ 886-2-2999-7742
2a. In Internet Settings / WAN /, select 3G Mode for your WAN Connection Type and choice your USB 3G modem type. And then press Apply
2b. In Internet Setting/LAN/, you may change the setting of IP address, DHCP and etc. then press Apply
3. In Wireless Settings / Basic, you may change the setting of SSID, and then press Apply
www.argtek.com
Fax :+ 886-2-2999-7742
4. In Wireless Settings / Security, you may change the setting of password, and then press Apply
Finish setting and press Apply, the setting will be completed after rebooting around 20 seconds.
Note: You have to connect cable line with LAN port of this equipment. =============================================================
www.argtek.com
Fax :+ 886-2-2999-7742