Documente Academic
Documente Profesional
Documente Cultură
Myers
AB O UT PENTAIR
Myers is located on 80 acres in Ashland and operates in a modern 410,000 square foot manufacturing, distribution, foundry, and office facility, employing approximately 600 people dedicated to supplying top quality jet and submersible well pumps; utility, sump and sewage pumps; effluent pumps; non-clog and other large waste handling pumps; and high pressure reciprocating and centrifugal pumps and pumping systems for residential, agricultural, commercial, municipal and industrial applications for North America and more than 100 foreign countries.
The Myers Mission is to provide extraordinary, responsive service and quality products so that our customers find it easy to do business with us.
Dealer for warranty service. At all times Myers shall have and possess the sole right and option to determine whether to repair or replace defective equipment, parts, or components. Damage due to lightning or conditions beyond the control of Myers is NOT COVERED BY THIS WARRANTY.
WARRANTY PERIOD
Pumps: 12/24 months depending on model; 18/30 months from date of manufacture. Labor, etc. Costs: Myers shall IN NO EVENT be responsible or liable for the cost of field labor or other charges incurred by any customer in removing and/or re-affixing any Myers product, part or component thereof. THIS WARRANTY WILL NOT APPLY: (a) to defects or malfunctions resulting from failure to properly install, operate or maintain the unit in accordance with printed instructions provided; (b) to failures resulting from abuse, accident or negligence; (c) to normal maintenance services and the parts used in connection with such service; (d) to units which are not installed in accordance with applicable local codes, ordinances and good trade practices; or (e) unit is used for purposes other than for what it was designed and manufactured, and (f) if three-phase submersible motors are installed on a single-phase power supply using a phase converter or if three-phase power is supplied by only two transformers, making an open Delta system. RETURN OR REPLACED COMPONENTS: Any item to be replaced under this Warranty must be returned to Myers in Ashland, Ohio, or such other place as Myers may designate, freight prepaid. PRODUCT IMPROVEMENTS: Myers reserves the right to change or improve its products or any portions thereof without being obligated to provide such a change or improvement for units sold and/or shipped prior to such a change or improvement. WARRANTY EXCLUSIONS: Myers SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AFTER THE TERMINATION OF THE WARRANTY PERIOD SET FORTH HEREIN. Some states do not permit some or all of the above warranty limitations and, therefore, such limitations may not apply to you. No warranties or representations at any time made by any representative of Myers shall vary or expand the provisions hereof. LIABILITY LIMITATION: IN NO EVENT SHALL Myers BE LIABLE OR RESPONSIBLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER TO ANY Myers PRODUCT OR PARTS THEREOF. PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY RESULT FROM IMPROPER INSTALLATION. Myers DISCLAIMS ALL LIABILITY, INCLUDING LIABILITY UNDER THIS WARRANTY, FOR IMPROPER INSTALLATIONMyers RECOMMENDS FOLLOWING THE INSTRUCTIONS IN THE INSTALLATION MANUAL. WHEN IN DOUBT, CONSULT A PROFESSIONAL. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state. In the absence of suitable proof of the purchase date, the effective date of this Warranty will be based upon the date of manufacture. DETERMINATION OF UNIT DATE OF MANUFACTURE: Submersible Sump Pump (8-95) month and year stamped on pump nameplate; Column Sump Pump month and year on red warranty tag.
For more information about Pentair Plumbing Products contact your local Myers Distributor, or our facilities in Ashland, Ohio.
1101 Myers Parkway Ashland, Ohio 44805 888/987-8677 Fax: 800-426-9446 269 Trillium Drive Kitchener, Ontario, Canada N2G 4W5 519/748-5470 Fax: 519/748-2553
293 WRIGHT STREET, DELAVAN, WI 53115 WWW.FEMYERS.COM PH: 888-987-8677 ORDERS FAX: 800-426-9446 Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice.
2013 Pentair Ltd. All Rights Reserved.
M9000SSE (01/10/13)
TABLE OF CONTENTS
U TILI T Y PUMPS
MES106 2 MCU15/MCU15S/MCU20S Series 5 MUSP125 6 SPS-6 7
4-8
DU25 8
S UMP PUMP S
MCSP Series 9 SP25 Series 10 S33 Series 11 SSM33I Series 12 MDC33/MDC50 Series 13 MCI033/MCI050 14 SX50 Series 15 DS Series 16
9-19
Sump Basin Package 17 ED-25 Sink Pump System 18 ED33 Series 19
20-21
22-32
2NFL and J-BE Series 30 DE Series 32
SE WAG E PUMP S
SRM4 33 CMV5 34 MW50 35 MW Series 36 WHR Series 37 WHR5H-WHR20H Series 38 DSW Series 39 SR1830 40 CMV1830 41 SRM-BP BasinPro 42
33-45
CMV-BP BasinPro 43 MW-BP 44 MRJ 45
G RI NDER PUMP S
MRG20 46
46-49
MRGD200 48 Turnkey Simplex Basin Package 49
GRINDER PUMPS
41-44
50-51
52-53
54-57
Iron Caulking & Compression-Type Hubs 57 Discharge and Conduit Flanges 57 Check Valves 57 Flexible Rubber Inlet Hubs 57 Basins and Covers 57
MFS Series Pump Switch 56 SA-1/OSA-1 Sump Alarms 57 CA-SS4 Alarm and Connection Box 57 Simplex, Duplex Structural Foam Junction Boxes 57
UTILIT Y PUMPS
MES106
Capacities Shut-off head Weight Liquids handling Motor Electrical data Discharge Power cord
Multi-Purpose Pump
S PE CIFICATIONS
5 GPM 10 4 lbs. drain water 40 C air-cooled brush motor 115V, 2A, 1, 60Hz Standard garden hose 6 18.9 LPM 3.1 m
FEATURES
Ideal for transferring water, filling tanks and draining shallow flooded areas Up to 5GPM with 10 head Connects to standard garden hose 115VAC with 9 power cord Removes standing water down to 1/8 depth Weighs only 4 lbs. Built-in carrying handle Includes 6 suction hose and floor drainer To operate, just attach a standard hose to pump discharge and plug into any 115V outlet. Air-cooled, high-torque, non-submersible motor with overload protection
PAGE 4
M9003 SSE
UTILIT Y PUMPS
200 GPH 120 GOH 20 15 3.25 lbs. drain water 190 F 115V, 1.45A, I, 60Hz 11 x 5 x 4-3/4 3/8 i.d. plastic tubing (not included) 2 Quarts
16
12
TOTAL HEAD IN FEET
16
MCU
20S
500
600
700
6 5
4
TOTAL HEAD IN METERS
MC
U1
U1
5/M
3 2 1
12
CU1 MCU2 5S 0S
5S
100
100 125
4 3
MC
8
5/M
CU1
2 1
0
0 0
25
25
50
50
75
75
125
150
150
175
175
200
43C
F EATURES
Ideal for the automatic removal of excess liquid which results from condensation Applications Air conditioner Dehumidifier Icemaker High-efficiency furnaces Refrigeration systems Water coolers Advantages By Design Lifts to 20 (MCU20S) Lifts to 15 (MCU15/15S) Built-in safety switch Low-profile unit, only 4-3/4 high Thermal overload protection High temperature housing Built-in check valve Double-insulated enclosure
Provides longer life than similar size condensate units Bearingless sealed motor offers a more reliable, longer life product * For indoor use only
PAGE 5
M9004 SSE
UTILIT Y PUMPS
MUSP125
Utility Sink Pump
S PE CIFICATIONS
Capacities Shut-off head Weight Liquids handling Motor Electrical data Housing Power cord 40 GPM 14 15 lbs. drain water up to 50 C 1/8 HP 115V, 4A, 1, 60Hz Thermoplastic 8 three-prong, SJTW 151.4 LPM 4.27 m
TOTAL HEAD IN FEET CAPACITY LITERS PER MINUTE
14 12 10 8 6 4 2 0 0 5 10 15 20 25 30 35 0 40 3 0 25 50 75 100 125 150 4
MUS
P12
51
/8 H
FEATURES
Ideal for basement wet bars, laundry and utility sinks Designed to be used with a sink where gravity drain line is not available Fully automatic operation Complete, compact system Easy to install - eliminates the need for traps, vents and costly labor Quiet, trouble-free operation - easily mounts beneath your sink Includes pump assembly, one-way valve, discharge shut-off/flow balancing valve, strainer cup CSA listed
PAGE 6
M9156 SSE
UTILIT Y PUMPS
SPS-6
Capacities Shut-off head Solids handling Liquids handling
S PE CIFICATIONS
20 GPM 22 1/8 drain water up to 140 F 1/6 HP PSC 115V, 2A, 1, 60Hz 6-9 3/4 threaded manual flame-retardant polypropylene 10, SJTW, SJTW-A type 11A, carbon & ceramic 19.05 mm threaded up to 60 C 75.7 LPM
TOTAL HEAD IN FEET
22 20 18 16 14 12 10 8 6 4 2 0
6.7 m 3.18 mm
SPS
-6
1/6
HP
5 4 3 2 1
Intermittent liquid temp. Motor Electrical Acceptable pH range Discharge, garden hose adapter Switch off/on Housing Power cord Mechanical seal
12
16
20
24
F EATURES
Ideal for light-duty drainage applications such as flooded basements, flat roofs and swimming pool covers Draining small decorative pools (for repairs, painting) Effective and easy to use Removes standing water down to 1/8 depth Weighs only 9 lbs. Built-in carrying handle To operate, just attach a standard hose to pump discharge and plug into any 115V outlet Provides longer life than similar size dewatering pumps Efficient PSC motor uses only 2A Air-filled motor housing; no oil required Full mechanical shaft seal lasts ten times longer than lip seals Built-in thermal overload protection CSA Listed
PAGE 7
M9005 SSE
UTILIT Y PUMPS
DU25
Applications Capacities
71.9 LPM 7m
15
DU2
Shut-off head Operations Pump-down range Solids handling Liquids handling Continuous liquid temp. Motor Electrical data Acceptable pH range Mechanical seal Housing Impeller Power cord Discharge, NPT Dimensions
51
/4 H
4.5
P
3
10
1.5
13
0 19
F EATU RES
Pumps up to 19 GPM Extra durable for heavy-duty use Used for dewatering shallow flooded areas such as basements, window wells, rooftops, ponds and stock tanks 1-1/4 NPT discharge 15 three-prong power cord Includes 1 x 3/4 garden hose adapter Pumps standing water down to 1/8 1-1/4 NPT x 1 NPT adapter Rated for continuous duty CSA Listed
PAGE 8
M9006 SSE
SUMP PUMPS
MCSP Series
1/3 HP Pedestal Sump Pumps
S PE CIFICATIONS
20
Capacities Shut-off head Operation: On Off Solids handling Liquids handling Liquid temp. Motor Electrical data Acceptable pH range Shaft seal Housing Power cord Discharge, NPT MCSP3: MCSP31: Min. sump diameter
16
MCSP
12
4 3
8 2 4 1 0 50
10
20
30
40
1625 RPM, 115V, 3.5A, 1, 60Hz 6-9 none thermoplastic or cast iron 6, 16/3, SJT 1-1/4 1-1/2 12 31.8 mm 38.1 mm 304.8 mm
F EATURES
Ideal for basements needing frequent drainage Quick and easy installation Fits 12 diameter x 24 deep or larger sump pits Available with corrosion-resistant thermoplastic or cast iron pump housing and base Built-in reliability, ease of operation Thermal overload protection to prevent motor overload Top-mounted adjustable float switch for easy accessibility Top-screened inlet to reduce clogging CSA Listed
PAGE 9
M9007 SSE
Applications
basement sumps
SUMP PUMPS
SP25 Series
S SPE PECIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Operation: On Off Solids handling Liquids handling Intermittent liquid temp Motor Electrical data Acceptable pH range Shaft seal Housing Power cord Discharge, NPT Min. sump diameter Wide Angle: Vertical:
32 GPM 22 9.5 2.5 1/4 drain water up to 140F 1/4 HP 115V, 6.5A, 1, 60Hz 6-9 carbon/ceramic cast iron 10, SJTW, SJTW-A 1-1/2 18 10
18 16 14 12 10 8 6 4 2 0 0 5 10
SP25
A1
1/4
HP
5 4 3 2 1
15
20
25
30
F EATU RES
Versatility for many light-duty jobs Designed for drain water removal or permanent applications with small amounts of debris Durable construction to deliver many years of reliable service Wide-angle or vertical mechanical switch Dual ball bearing Powerful permanent split capacitor run motor Built-in overload protection Cast iron housing for superior heat dissipation Non-clogging recessed impeller Long-life carbon/ ceramic seal Positive sealing, quick-disconnect power and switch cords make replacement simple 10 power cord Energy-saving, low-amp motor CSA Listed
PAGE 10
M9008 SSE
SUMP PUMPS
S33 Series
S SPE PECIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Operation: On Off Pump-down range Solids handling Liquids handling Intermittent liquid temp Motor Electrical data Acceptable pH range Shaft seal Housing Power cord Discharge, NPT Min. sump diameter Float: Vertical:
32 GPM 25 10.31 3.31 7 1/4 drain water up to 140F 1/3 HP, PSC
20 18 16 14 12 10 8 6 4 2 0 0 5 10 15
1/3
HP
6 5 4 3 2 1
20
25
30
3000 RPM, 115V, 6.5A, 1, 60Hz 6-9 type 11A, carbon & ceramic, secondary lip seal cast iron 10, 20 1-1/2 18 10-1/2 38.1 mm 457 mm 267 mm
F EATU RES
Versatility for many light-duty jobs Designed for drain water removal or permanent applications with small amounts of debris Maintenance-free operation Wide-angle or vertical mechanical switch for small 10-1/2diameter sumps Dual ball-bearing motor and additional lip seal provide durability and longer pump life Durable PSC motor for years of service Oil-filled PSC motor for maximum heat dissipation, continuous bearing lubrication Recessed vortex impeller for free flow of liquids and solids Thermal overload protection with automatic reset CSA Listed
PAGE 11
M9009SSE
S33
SUMP PUMPS
SSM331 Series
S SPE PECIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Operation: On Off Solids handling Liquids handling Intermittent liquid temp Motor Electrical data Acceptable pH range Shaft seal Housing Power cord Discharge, NPT Min. sump diameter 31 GPM 23 9.94 4.06 1/2
18 16 14 12 10 8 6 4 2 0 0 5 10 15 20 25 30 2 1 5 4 3
drainage effluent up to 140F 1/3 HP Shaded pole, 115V, 9A, 1, 60Hz 5-9 type 11A, carbon & ceramic heavy cast iron 10 (3 m), 16/3, SJTW, SJTW-A 1-1/2 12 304.8 mm
F EATU RES
Designed for light demanding drainage applications Removal of drainage water and light septic tank effluent Automatic and manual operation models available Maintenance-free operation Piggyback wide-angle or vertical mechanical switch Heavy-duty reliability Oil-filled motor for maximum heat dissipation, continuous bearing lubrication Recessed vortex impeller for free flow of liquids and solids Thermal overload protection with automatic reset CSA Listed
PAGE 12
M9010 SSE
SSM331 1/3 HP
SUMP PUMPS
MDC33/MDC50 Series
1/3 and 1/2 HP Cast Iron Submersible Sump Pumps
S SPE PECIFICATIONS CIFICATI ONS
40
30
MDC
Capacities Shut-off head Operation: Manual Tethered models: On Off Vertical models: On Off Solids handling Liquids handling Intermittent liquid temp Motor electrical data
62 GPM 32
50 1
/2 H
P
6
20
MDC
33
1/3
HP
4 2 0
10
20
40
60
80
1/3 HP, 9.8A; 1/2 HP, 12A; shaded pole w/thermal overload protection,115V, 1, 60Hz, 1550 RPM 6-9 carbon & ceramic heavy cast iron 10 (3 m) or 20 (6 m), 16/3, SJTW, SJTW-A 1-1/2 14 10 356 mm 254 mm
Acceptable pH range Shaft seal Housing Power cord Discharge, NPT Min. sump diameter Float: Vertical:
F EATU RES
1/3 or 1/2 HP Rugged cast iron pump body and motor cover, exterior hardware stainless steel construction 1-1/2 (38 mm) NPT discharge Carbon/ceramic shaft seal Piggyback-style float for automatic or manual operation Oil-filled motor with automatic reset overload provides safe operation Ball-bearing construction for long life Easily replaceable power cord with optional lengths available CSA Listed
PAGE 13
M9011SSE
Applications
10
SUMP PUMPS
MCI033/MCI050 Series
1/3 and 1/2 HP Cast Iron Submersible Sump Pumps
S SPE PECIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Operation: On Off Operation Solids handling Liquids handling Continuous liquid temp Motor electrical data basement sumps, dewatering, light effluent, water transfer 62 GPM 32 9 4 automatic 1/2 drainage effluent 130F 54C 1/3 HP, 9.8A; 1/2 HP, 12A; shaded pole w/thermal overload protection, 115V, 1, 60Hz, 1550 RPM 6-9 carbon & ceramic heavy cast iron fiberglass reinforced polypropylene fiberglass-reinforced Noryl with threaded brass insert stainless steel 10 (3 m) or 20 (6 m), 16/3, SJTW-A, SJTW 1-1/2 10 38.1 mm 25.4 cm 12.7 mm 235 LPM 9.8 m 229 mm 102 mm
CAPACITY LITERS PER MINUTE
35 30 0 50 100 150 200 250 10
8 25 20 15 10 5 0 2
MCI0
MCI
33 1 /3 HP
050
1/2
HP
10
20
30
40
50
60
0 70
Acceptable pH range Shaft seal Housing/volute Volute base Impeller Exterior hardware Power cord Discharge, NPT Min. sump diameter
F EATU RES
2-pole switch design allows for operation in sump diameters of 10 or more Rugged, oil-cooled motor provides continuous bearing lubrication and maximizes heat dissipation Lubricated ball bearings and shaft seal for longer service life Shaded pole motor eliminates failure-prone switches and relays Long-life carbon/ceramic seal protects motor against water leakage Heat sensor overload protection with automatic reset when motor cools to safe operating temperature Anti-airlock hole in base reduces added labor Pump intake screen, volute base, switch and power cord are serviceable CSA Listed
PAGE 14
M9180 SSE
SUMP PUMPS
SX50 Series
S SP PE E CIFICATI CIFICATIONS ONS
Applications Capacities Shut-off head Operation: On/Off Solids handling Liquids handling Intermittent liquid temp Motorn electrical data Acceptable pH range Winding insulation temp. (Class B) Specific gravity Viscosity Discharge, NPT SX50: SX50H: Min. sump diameter Simplex: Duplex:
40
50
100
300
350
12 10 8
95 GPM 34
360 LPM 10 m
30 25 20 15 10 5 0 0 10 20 30
0H
SX50
6 4 2 0 100
turns on/off with tethered switch hooked to control box (SX50; SX50H) 2 / 3/4 50 mm / 19 mm domestic effluent & drain water up to 140F up to 60C 1/2 HP, 1750 RPM, 1 - capacitor start, 230V, 60Hz 6-9 266F .9-1.1 28 35 SSU 2 1-1/2 24 36 50 mm 38.1 mm 61.0 mm 91.4 mm up to 120C
40
50
60
70
80
90
F EATURES
Rugged, submersible, explosion-proof sump pumps for municipal, commercial and industrial use Constructed for use in Class 1, Division 1, Group D hazardous locations Designed to pump contaminated water, with a wide range of pollutants listed under the CSA listings Intrinsically safe control panel included Durable motor will deliver many years of reliable service Oil-filled motor for maximum heat dissipation and constant bearing lubrication Recessed impeller reduces radial bearing loads, increasing bearing life High-torque capacitor start, single-phase motor for assured starting under heavy load Seal leak probes warn of seal leak condition On-winding heat sensors protect motor from overheating and prevent costly motor damage
PAGE 15
M9015SSE
35
SX5
SUMP PUMPS
DS Series
S SPE PECIFICATI PECIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Operation: On Off Solids handling Liquids handling Continuous liquid temp Motor electrical data Acceptable pH range Shaft seal Housing Power cord Discharge, NPT Min. sump diameter
30
19
38
152
170
20 15 10 5 0
DS75
DS5 01
3/4
HP
3 1.5 0
/2 H
10
15
20
25
30
35
40
45
50
1/3 HP, 2.7A; 1/2 HP, 4.8A; 3/4 HP, 6.4A; 115V; 60Hz, PSC Motor, 3450 RPM 5-9 dual lip with ceramic shaft seal stainless steel 15, SJTW, 18/3 1-1/4 12
F EATU RES
Used for dewatering from construction sites, ponds, pits, tanks and extracting water from foundations or flooded basements 1/3 HP, 1/2 HP and 3/4 HP available PSC motor with selflubricating ball-bearing construction Double lip seals with ceramic wear surface Passes 3/4 solids Piggyback-style float allows for manual operation Includes 1-1/4 NPT x 1-1/4 NPT 90 discharge elbow, 1-1/4 NPT x 1-1/2 NPT adapter CSA Listed
PAGE 16
M9016 SSE
25
DS3 31 H /3 P
SUMP PUMPS
PSB1822
S SPE PECIFICATI PECIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Operation: On Off Solids handling Liquids handling
18 16 14 12 10 8 6 4 2 0 0 5 10
32 GPM 22 9.5 2.5 1/4 drain water up to 140F carbon & ceramic cast iron 10, SJTW, SJTW-A 1-1/2
SP25
A1
1/4
HP
5 4 3 2 1
15
20
25
30
Intermittent liquid temp Motor electrical data Shaft seal Housing Power cord Discharge, NPT
38.1 mm
Pump Only
F EATU RES
1/4 HP Fully assembled check valve includes Injection-molded structural foam provides the highest quality construction for uniform wall thickness and strength Proprietary flush mount design for easy shipping and storage allows for pallet stacking for sump Basin Features: Radon proof radon approved basin and cover for radon prevention Injection-molded structural foam (polyethylene) 20-gallon capacity basin; standard 18 x 22 size Injection-molded structural foam (polyethylene) lid; gas-tight single-piece design with seal
4 snap-in type hub adapter with stainless steel clamp; fits 4 DWV SCH. 40 plastic pipe 1-1/2 NPT threaded discharge and 2 NPT vent flange (easily converts to 3); comes with gas-tight cord grommet Sump pump check valve fits 1-1/2 black, galvanized, and DWV SCH. 40 pipe
PAGE 17
M9155SSE
SUMP PUMPS
ED-25
Applications Capacities Shut-off head Operation: On Off Solids handling
18 16 14 12 10 8 6 4 2 0 0 5 10
ED2
51
/4 H
5 4 3 2 1
Liquids handling Intermittent liquid temp Motor electrical data Shaft seal Housing Power cord Discharge, NPT Min. sump diameter
15
20
25
30
Pump Only
F EATU RES
Specially designed for many household jobs Pumps water from laundry trays, washing machines, wet bars, water softeners, dehumidifiers, etc. High-capacity 1/4 HP pump Oil-filled for maximum heat dissipation and constant lubrication Thermal overload protection with automatic reset Fully assembled Includes discharge pipe inside basin Installs above floor no need for sump
PAGE 18
M9017 SSE
SUMP PUMPS
ED33 Series
1/3 HP Sink Pump System
S SPE PECIFICATIONS CIFICATI ONS
25
Capacities Shut-off head Operation: On Off Solids handling Liquids handling Motor electrical data Acceptable pH range Shaft seal Housing Power cord Discharge, NPT
15
ED3
3 1/
3H
4 3 2 1
10
10
20
30
40
50
Intermittent liquid temp 130F 5-9 carbon & ceramic cast iron
54C
Pump Only
F EATU RES
1/3 HP Pre-packaged sink/pump system is ready for quick application Basin Features: High-impact engineered resin, exterior hardware and stainless steel construction 1-1/2 (38 mm) NPT discharge Carbon/ceramic shaft seal Piggyback-style float for automatic or manual operation Oil-filled motor with automatic reset overload provides safe operation Octagonal shape, compact size, 6-gallon useable capacity Easily replaceable power cord with optional lengths available Molded reuseable PNC gasket lid seal Basin dimensions are 15-1/16 W x 13 3/8 H (11-9/16 from floor to center of inlet)
PAGE 19
M9018SSE
Applications
20
MBSP
Applications Capacities Shut-off head
12 10 8 6 4 2 0 0 5 10 15
MBS
3.5
P1
2V
DC
2.5
1.5
.5 20 25 30 35
plug-in type wall-mounted transformer; input - 120V AC, 60Hz, 15W; output - 12V AC, 60Hz, 2A dual check valves provided thermoplastic
F EATU RES
Protects home if AC-powered pump fails Backs up residential sump pump automatically during power outage or pump failure (primary pump and piping not included) Reliable operation Continuous self-charging system Solid-state controller monitors battery charge and pump operation Alarm sounds when standby pump activates Controller includes connectors for pump, charger, float switch and battery* Area light lights up dark, powerless work area Works with flooded and sealed AGM deep cycle lead-acid battery Re-settable circuit breaker eliminates the need for a fuse 2A 5-stage charger
* Deep cycle marine-type battery (Group 24) recommended not included with MBSP system
PAGE 20
M9019 SSE
emergency dewatering
TOTAL HEAD IN FEET
14
MBSP-Plus Series
12 Volt Battery Standby Pump System
S SP PECIFICATIONS PE E CIFICATI CIFICATIONS ONS
20
Capacities Shut-off head Liquids handling Continuous liquid temp Motor Charger
10,220 LPH
15
MBS
10
P-P
LUS
3 2
up to 25C
5 1 0
fully automatic, computerized monitoring, control and alarm system; input - 115V AC, 60Hz; output - 12V AC, 8A (5 stages) included thermoplastic
12.5
25
37.5
50
F EATURES
2700 GPH (10,220 LPH), 8A 5-stage charging system Thermoplastic pump with steel case charger enclosure 1-1/4 (32 mm) NPT threaded discharge; adapts to 1-1/4 (32 mm) and 1-1/2 (38 mm) NPT High volume ideal for active sump pits 8A multi-stage charging system (UL/CUL approved) with steel enclosure provides the strongest battery charge Plug-in style connectors for quick and easy installation Audio and visual alarms keep you informed of status at all times Check valve and battery case included Fits most new and existing sump pits
PAGE 21
M9020SSE
Applications
emergency dewatering
TOTAL HEAD IN FEET
EFFLUENT PUMPS
S40HT
Applications Shut-off head Capacities
Operation (S40HT-11P): On Off Operation Solids handling Liquids handling Intermittent liquid temp. S40HT-11P S40HT-11 Motor electrical data Acceptable pH range Housing/volute case Impeller Exterior hardware
16 12 8
S40HT
PERFORMANCE @ 194F WATER TEMPERATURE
5 4 3 2
4 0 0 10
F EATU RES
All cast-iron housing, volute case, and impeller resists the most extreme corrosive environments Rugged-built, oil-filled motor for continuous bearing lubrication and maximum heat dissipation Heat sensor overload protection with automatic reset when motor cools to a safe operating temperature Lower ball bearing eliminates sleeve bearing wear and reduces motor wear Non-clog vortex style impeller, ejector vanes for seal protection Stainless steel hardware allows easy disassembly after extended service Oil and water resistant cord design prevents oil loss from and moisture protection for motor Bearings and mechanical seal are permanently lubricated for long life Easy to service heavy-duty lift-out ring CSA Listed
20
30
40
50
PAGE 22
M9013 SSE
1/3 HP, oil-filled, thermal overload protection, 115V, 12A, 1, 60Hz, 1550 RPM
EFFLUENT PUMPS
S50HT Series
S SPE PECIFICATI PECIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Max. spherical solids Liquids handling Max. liquid temp. Motor electrical data Acceptable pH range Specific gravity Viscosity Discharge, NPT Housing Min. sump diameter Simplex: Duplex: Power cord
30
S50 HT 1/2 HP PERFORMANCE @70F WATER TEMPERATURE S50 HT 1/2 HP PERFORMANCE @200F WATER TEMPERATURE
12
domestic effluent and drain water 1/2 HP, 3450 RPM, PSC with thermal overload, 115V, 12 FLA, 1, 60Hz 5-9 .91.1 2835 SSU 2 cast iron 24 36 61.0 mm 91.4 mm 50.8 mm
15
30
60
90
120
F EATU RES
1/2 HP Class 30 cast iron construction 2 (50.8 mm) NPT discharge Silicon carbide shaft seals Oil-filled motor with automatic reset overload provides safe operation Ball-bearing construction for long life 600V jacketed lead for added durability Easily replaceable power cord with optional lengths available CSA Listed
PAGE 23
M9014SSE
EFFLUENT PUMPS
ME3 Series
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
Applications Capacities ME3H: ME3F: Shut-off head ME3H: ME3F: Max. spherical solids Liquids handling Intermittent liquid temp. Motor electrical data Acceptable pH range Specific gravity Viscosity Discharge, NPT Housing Min. sump diameter Simplex: Duplex: Power cord
1/3 HP High Head (ME3H) and High Flow (ME3F) Submersible Effluent Pumps
CAPACITY LITERS PER MINUTE
30 25 20 15 10 5 0 0 10
ME3
F1
/3 H
6 4 2 0 100
domestic effluent and drain water 1/3 HP, 1550 RPM, shaded pole, oil-filled, 115V, 12A, 1, 60Hz, 230V, 6A, 1, 60Hz 6-9 .91.1 28 35 SSU 1-1/2 heavy cast iron 24 36 20, 16/3, SJTW 61.0 mm 91.4 mm 38.1 mm
20
30
40
50
60
70
80
90
ME3F
ME3H
F EATU RES
Durable motor delivers years of reliable service Oil-filled motor for maximum heat dissipation and continuous bearing lubrication Overload protected, shaded pole motor eliminates starting switches and relays which are prone to fail Heavy cast iron motor housing and volute case dissipate heat, allow motor to run cooler for extended life Engineered for maintenance-free operation Field-tested, wide-angle, mercury-free mechanical float switch for maximum drawdown (automatic piggyback models only) Automatic pump models can be operated manually by unplugging piggyback switch and plugging pump directly into outlet Passes full 3/4 solids CSA Listed
PAGE 24
M9021 SSE
40 35
50
100
150
200
250
300
350
ME3
12 10
H1
/3
HP
EFFLUENT PUMPS
ME40 Series
S SPE PECIFICATI PECIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Max. spherical solids Liquids handling Intermittent liquid temp. Motor electrical data Acceptable pH range Specific gravity Viscosity Discharge, NPT Housing Min. sump diameter Simplex: Duplex: Power cord
30 25 20 15 10 5 0 0 10 20 30 40 50 60 70 80 90 2 0 100
ME4
0 4/
10 H
6 4
domestic effluent and drain water 4/10 HP: 1650 RPM, PSC, oil-filled; 115V, 12A, 1, 60Hz; 230V, 6A, 1, 60Hz 5-9 .91.1 2835 SSU 1-1/2 cast iron 24 36 20, 16/3, SJTW 61.0 mm 91.4 mm 38.1 mm
F EATU RES
Two-vane cast iron impeller design provides maximum dosing efficiency Enclosed design for high- efficiency pumping Eliminates possibility of jamming between impeller and volute Passes full 3/4 solids Durable motor will deliver many years of reliable service Oil-filled motor for maximum heat dissipation and continuous bearing lubrication Positive sealing, quick- connect float and switch cords make replacement simple if service is ever necessary Field-tested, wide-angle, mercury-free mechanical float switch provides maximum drawdown (automatic models only) Lower ball bearing and heavy-duty, type 6 seal for added pump life CSA Listed
PAGE 25
M9022SSE
35
EFFLUENT PUMPS
ME45 Series
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Max. spherical solids Liquids handling Intermittent liquid temp. Motor electrical data Acceptable pH range Specific gravity Viscosity Discharge, NPT ME40: ME45: Housing Min. sump diameter Simplex: Duplex: Power cord
ME4
5 1/
30
2H
20
domestic effluent and drain water 1/2 HP: 3450 RPM, PSC, oil-filled; 115V, 8.6A, 1, 60Hz; 230V, 4.3A, 1, 60Hz 5-9 .91.1 28 35 SSU 1-1/2 2 cast iron 24 36 20, 16/3, SJTW 61.0 mm 91.4 mm 38.1 mm 50.8 mm
10
0 0 10 20 30 40 50 60 70 80 90
0 100
F EATU RES
Two-vane cast iron impeller design provides maximum dosing efficiency Enclosed design for high- efficiency pumping Eliminates possibility of jamming between impeller and volute Passes full 3/4 solids Durable motor will deliver many years of reliable service Oil-filled motor for maximum heat dissipation and continuous bearing lubrication Positive sealing, quickconnect float and switch cords make replacement simple if service is ever necessary Field-tested, wide-angle, mercury-free mechanical float switch provides maximum drawdown (automatic models only) Lower ball bearing and heavy-duty, type 6 seal for added pump life CSA Listed
PAGE 26
M9185 SSE
40
12
EFFLUENT PUMPS
ME Series
S SPE PECIFICATI PECIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Max. spherical solids Liquids handling Intermittent liquid temp. Motor electrical data
70 60 50 40 30 20 10 0 0 10 20 30 40
20 16 12 8 4
domestic effluent and drain water 1/2 HP, 115V, 1, 1/2 to 1-1/2 HP, 230V, 1, 208/230/ 460/575V, 3, oil-filled, permanent split capacitor type, 1, 3450 RPM, 60Hz 6-9 .91.1 2835 SSU 2 cast iron 24 36 10 61.0 mm 91.4 mm 50.8 mm
50
60
70
80
90
100
110
120
130
Acceptable pH range Specific gravity Viscosity Discharge, NPT Housing Min. sump diameter Simplex: Duplex: Power cord
F EATU RES
Ideal for use in mound and trench pressure distribution systems High-efficiency, two-vane, enclosed impeller provides ideal performance for efficient dosing Impeller passes full 3/4 solids Enclosed impeller design eliminates the possibility of jamming or corrosion between impeller and volute Durable motor will deliver many years of reliable service Oil-filled motor for maximum heat dissipation and constant bearing lubrication High-torque, permanent split capacitor (PSC), single- phase motors; no starting switches or relays to wear out Optional seal leak probe warns of seal leak condition (dual seal motors only); helps prevent costly motor damage Motors have a winding current and temperaturesensitive overload (single phase only) Volute seal ring is replaceable; restores pump to original performance if wear should occur Motor is held in place by 4 screws; easily removed if service is ever needed CSA Listed
PAGE 27
M9023SSE
90 80
ME15
24
EFFLUENT PUMPS
P50/P100 Series
1/2 and 1 HP Effluent ST.E.P. Pumps
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
140
Applications Capacities Shut-off head Max. spherical solids Liquids handling Intermittent liquid temp. Motor electrical data
100 80 60 40 20 0
32 28
24 20 16 12 8 4
domestic effluent and drain water 1/2 HP, 115V or 230V, 1; 1 HP, 230V, 1, oil-filled, permanent split capacitor type, 3450 RPM, 60Hz 6-9 .91.1 28 35 SSU 1-1/2 cast iron 24 36 61.0 mm 91.4 mm 38.1 mm
10
15
20
25
30
35
40
45
50
55
60
Acceptable pH range Specific gravity Viscosity Discharge, NPT Housing Min. sump diameter Simplex: Duplex: Power cord
F EATURES
P Series effluent pumps are designed for years of maintenance-free operation Single-vane, enclosed impeller provides steep, non-overloading performance curve for pressure collection and ST.E.P. systems; out-performs most pumps in its class Enclosed impeller eliminates the possibility of jamming or corrosion between impeller and volute Passes 3/4 spherical solids Durable motor will deliver many years of reliable service Oil-filled motor for maximum heat dissipation and continuous bearing lubrication High-torque, permanent split capacitor (PSC), singlephase motors; no starting switches or relays to wear out Double tandem seal configuration for extra motor protection, tough effluent pumping applications Optional seal leak probes warn of seal leak condition; helps prevent costly motor damage On-winding current and temperature-sensitive overload to protect against costly burnout Volute seal ring is replaceable; restores pump to original performance if wear should occur Motor is held in place by 4 screws; easily removed if service is ever needed CSA Listed
PAGE 28
M9024 SSE
120
P102 1 HP
36
EFFLUENT PUMPS
MD Series
S SPE PECIFICATI PECIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Max. spherical solids Liquids handling Max liquid temp. Motor electrical data Specific gravity Viscosity Discharge, NPT Housing Power cord
60
150
40
75
20
GP
30
1/2
GPM
20
Dry-wound, double ball bearing, double-seal, thermal overload protected, 115V, 1, 60Hz .91.1 2835 SSU 1-1/4 stainless steel and composite 10 30 m 300V, 2-wire with ground, SJTW-A, SJTW
HP
30
1/2
HP
45 60
15
F EATU RES
1/2 HP, 115V, single-phase Superior drawdown capability to 4-1/2 (114 mm) vs. 13-1/2 (343 mm) on a standard NEMA 4 25% reduced amp-draw 9.5A vs. 12.7A on a standard NEMA 4 Cooler and quieter operation eliminates expensive flow-inducer sleeves Stainless steel and composite construction Exclusive dry-run capability Enclosed and self-lubricated shaft-bearing resists wear from abrasives Heavy 7/16 (12 mm) positive drive 300 Series stainless steel hexagonal shaft Serviceable composite intake screen allows for 0.80 solids
PAGE 29
M9026 SSE
225
10 GP M 1/2 HP
EFFLUENT PUMPS
1/2 HP, 115V, 1, 1/2 to 1-1/2 HP, 230V, 1, 60Hz, 3450 RPM .91.1 28 35 SSU 1-1/4 2 stainless steel 10, 30, 50 or 100, jacketed, 14/3, SOOW 31.8 mm 50.8 mm
F EATURES
Cost-effective wastewater systems High-pressure capacity Corrosion-resistant design for long life Dependable field proven motor Stainless steel construction Built-in overload protection Replaceable 10, 30, 50 or 100 jacketed power cord Hermetically sealed windings Continuous-duty rating Frequent cycling capabilities Powerful, yet lightweight Easy handling and installation
2NFL
J-BE
PAGE 30
M9027 SSE
EFFLUENT PUMPS
12 GPM 2NFL
CAPACITY LITERS PER MINUTE
8 500 15 23 30 38 45 53 60 68 75 150
1 HP
3/4 HP
1/2 HP
400
120
400
1 HP 3/4 HP
120
300
90
300
1/2 HP
90
200
60
200
60
100
30
100
30
10
12
14
16
18
20
10
12
14
16
18
20
20 GPM 2NFL
CAPACITY LITERS PER MINUTE
11 500 23 34 45 57 68 80 91 102 114 150
25 GPM J-BE
CAPACITY LITERS PER MINUTE
19 500 38 57 76 95 114 133 151 170 189 150
400
120
400
120
300
90
300
1-1/2 HP
90
200
60
200
1 HP
1/2 HP
60
100
30
100
30
12
15
18
21
24
27
30
10
15
20
25
30
35
40
45
50
35 GPM J-BE
CAPACITY LITERS PER MINUTE
19 250 38 57 76 95 114 133 151 170 189 75
200
60
1-1/2 HP
150 45
1 HP
100 30
50
15
10
15
20
25
30
35
40
45
50
PAGE 31
M9027 SSE
EFFLUENT PUMPS
DE Series
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Max. spherical solids Liquids handling Continuous liquid temp. Motor electrical data Acceptable pH range Specific gravity Viscosity Discharge NPT Housing Min. sump diameter Simplex: Duplex: Power cord
45 12 9 6 3 0 100
30
DE50
domestic effluent and drain water 4/101/2 HP, 115V; 4/10 HP, 10.5A; 1/2 HP, 12A; 60Hz 5-9 .91.1 28 35 SSU 2 stainless steel 18 24 20, SJOW, 16 AWG 46 mm 60 mm 50 mm
15
25
50
75
F EATURES
Pumps up to 97 GPM (1/2 HP) and 92 GPM (4/10 HP) Designed to quickly clear water or effluent PSC motor with self-lubricating ball-bearing construction Ideal for residential and commercial applications Tethered float switch Double-lip seal with ceramic wear surface Suitable for continuous use Includes 90 discharge elbow CSA Listed
PAGE 32
M9028 SSE
SEWAGE PUMPS
SRM4
Applications Capacities Shut-off head
16 12 8
SRM4
4/10
HP
4 3 2
Solids handling Liquids handling Intermittent liquid temp Motor electrical data Acceptable pH range Discharge, NPT Housing Power cord Impeller Volute case Shaft seal
septic effluent and sewage 4/10 HP, PSC, 115V, 12A, 1, 60Hz 50.8 mm
4 0
10
20
30
40
50
60
70
80
90
F EATURES
Power for versatile applications Residential septic tank sewage Large sumps Long-lasting performance Oil-filled motor for maximum heat dissipation and continuous bearing lubrication Recessed vortex impeller for free flow of liquids, solids up to 2 diameter Rotary shaft seal has carbon and ceramic faces for positive seal Thermal overload protection with automatic reset CSA Listed
PAGE 33
M9029SSE
20
SEWAGE PUMPS
CMV5
Applications Capacities Shut-off head 18 shut-off: 19 shut-off:
15 4 10
360 LPM
CMV
51
/2 H
P
2
Solids handling Liquids handling Intermittent liquid temp. Motor electrical data Acceptable pH range Discharge NPT Housing Power cord Impeller Volute case Shaft seal Min. sump diameter Simplex: Duplex:
50.8 mm
5 1 0 0 100
raw sewage, effluent and drain water up to 140F up to 60C 1/2 HP, PSC, 1625 RPM, 115V, 12A, 1, 60Hz 6-9 2 cast iron 20, 16/3, SJTW recessed, thermoplastic thermoplastic type 11A, carbon & ceramic 18 30 457 mm 762 mm 50.8 mm
10
20
30
40
50
60
70
80
90
F EATURES
Engineered for many years of maintenance-free operation Wide-angle, mercury-free mechanical float switch for maximum drawdown Recessed vortex impeller operates completely out of volute and provides free flow through passage for solids and liquids Durable motor will deliver many years of reliable service Oil-filled motor for maximum heat dissipation and continuous bearing lubrication Recessed vortex impeller provides minimal radial loading for long bearing life CSA Listed
PAGE 34
M9030 SSE
SEWAGE PUMPS
MW50
Applications Capacities Shut-off head Solids handling
20
MW5
15 10 5 0
0 1/ 2 HP
Liquids handling Intermittent liquid temp Motor electrical data Acceptable pH range Discharge, NPT Housing Power cord Impeller Volute case Shaft seal Min. sump diameter Simplex: Duplex:
domestic sewage & drain water 1/2 HP, 1625 RPM, PSC (1), oil-filled, 115V, 9A, 1, 60Hz; 230V, 4.5A, 1, 60Hz 5-9 2 class 30 cast iron 20, 16/3, SJTW thermoplastic cast iron type 6, carbon & ceramic 24 36 61.0 cm 91.4 cm 50.8 mm
20
40
60
80
100
120
0 140
F EATURES
Two-vane impeller design provides maximum pump efficiency Enclosed design for high-efficiency pumping Eliminates possibility of jamming between impeller and volute Passes full 2 solids Original performance can be restored if wear occurs by replacing volute seal ring Durable motor will deliver many years of reliable service Oil-filled motor for maximum heat dissipation and continuous bearing lubrication High-torque, permanent split capacitor (PSC) motors; no starting switches or relays to wear out Field-tested, wide-angle, mercury-free piggyback mechanical float switch provides maximum drawdown (automatic models only) Long, flexible type 6 seal provides high-pressure sealing with improved seal face protection by location Lower ball bearing eliminates sleeve bearing wear and significantly reduces motor wear Low-amp draw from the efficient PSC motor means less heat build-up CSA Listed
PAGE 35
M9031SSE
SEWAGE PUMPS
MW Series
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Solids handling Liquids handling Intermittent liquid temp. Motor electrical data
2" Solids Handling Heavy-Duty Residential and Commercial Sewage Pumps Available with Single or Double Seals
0 100
80
500
600
60 50 40 30 20 10 0 0 20 40 60
MW150
MW200 1-1/2 H 2 HP P
15
10
domestic sewage & drain water 1/2 to 2 HP, 208/230V, 1; 208/230/460/575V, 3, oil-filled, permanent split, capacitor type, 1, 3450 RPM, 60Hz 5-9 2 cast iron 10 ductile iron class 30 cast iron type 21, carbon & ceramic 24 36 61.0 cm 91.4 cm 50.8 mm
80
100
120
140
160
0 180
Acceptable pH range Discharge, NPT Housing Power cord Impeller Volute case Shaft seal Min. sump diameter Simplex: Duplex:
F EATURES
High head performance for demanding applications High-efficiency, two-vane, enclosed impeller for high- efficiency pumping Eliminates possibility of jamming between impeller and volute Original performance can be restored if wear occurs by replacing volute seal ring Durable motor will deliver many years of reliable service Oil-filled motor for maximum heat dissipation and continuous bearing lubrication High-torque, permanent split capacitor (PSC) single-phase motors; no starting switches or relays to wear out CSA Listed
PAGE 36
M9032 SSE
70
20
SEWAGE PUMPS
WHR Series
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Solids handling Liquids handling Intermittent liquid temp Motor electrical data Acceptable pH range Discharge, NPT Housing Power cord
2" Solids Handling Heavy-Duty Residential and Commercial Sewage Pumps Available with Single or Double Seals
CAPACITY LITERS PER MINUTE
76 152 228 304 380 456 532 608 684 9.6 32 28
24 20 16 12 8 4 0 0
drain water and domestic sewage 1/2 HP, 115V, 1, 60Hz, PSC; 1/2, 3/4, 1 HP, 230V, 1, 60 Hz PSC; 200/230/460/575V, 3, 60Hz 5-9 2 3 cast iron WHRSJOW/SJOW-A 20, 16/3, 1; 20, 16/4, 3 WHR-DS 20, 14/4, 1 20, 14/3, 1, L/D; 20, 16/4, 3, L/D cast iron, vortex cast iron single type 21, carbon/ceramic, double tandem carbon/ceramic 24 30 61.0 cm 76.0 cm 50.8 mm 76.2 mm
20
40
60
80
100
120
140
160
180
Impeller Volute case Shaft seal Min. sump diameter Simplex: Duplex:
F EATURES
Power range meets many applications Domestic wastewater and septic systems Light commercial sewage High-capacity fluid transfer Durable motor for long-lasting performance 1/2, 3/4 and 1 HP models Oil-filled for cooler operation and constant bearing lubrication Single-phase PSC motors eliminate starting switches Recessed impeller increases bearing life Thermal overload protection with automatic reset Double seal models with seal leak detector are not CSA Listed
PAGE 37
M9033SSE
1 HP & WH R10-D WHR7 S 3/4 H P& WHR WHR5 7-DS 1/2 H P& WHR 5-DS
WHR10
8.4
SEWAGE PUMPS
WHR5H-WHR20H Series
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Solids handling Liquids handling Intermittent liquid temp. Motor electrical data Acceptable pH range Discharge NPT Housing Power cord Impeller Volute case Shaft seal Min. sump diameter Simplex: Duplex: domestic wastewater and septic systems 218 GPM 70 2 up to 140F 825 LPM 20.9 m 50.8 mm up to 60C
2" Solids Handling Residential and Commercial Sewage and Effluent Pumps
50 40 30 20 10 0
WHR
WHR
WHR
15H
2 HP
2 HP
10H
1-1/
15
5H 1 /2
1 HP
HP
10
raw sewage and sewage effluent 1/2, 1, 1-1/2 & 2 HP, 3450 RPM, 200/230V, 1, 60 Hz, PSC; 200/230/460V, 3, 60Hz 6-9 2 3 cast iron 20, 16/3, SJOW/SJOW-A, 1 20, 16/4, SJOW/SJOW-A, 3 ductile iron, vortex cast iron type 21, carbon & ceramic 24 30 61.0 cm 76.0 cm 50.8 mm 76.2 mm
20
40
60
80
100
120
140
160
180
200
220
240
F EATURES
Higher heads for demanding applications Domestic wastewater and septic systems Light commercial sewage High-capacity fluid transfer Durable motor for long-lasting performance 1/2, 1, 1-1/2 and 2 HP models Oil-filled for cooler operation and constant bearing lubrication Single-phase PSC motors eliminate starting switches Recessed impeller reduces radial loads and increases bearing life Thermal overload protection with automatic reset CSA Listed
PAGE 38
M9034 SSE
WHR
20H
SEWAGE PUMPS
DSW Series
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Solids handling Liquids handling Continuous liquid temp Motor electrical data Acceptable pH range Discharge, NPT Housing Power cord Impeller Volute case Shaft seal
35 30 25 20 15 10 5 0 0
DSW
DSW
40
4/10
50 1 /2
sewage, wastewater, effluent 4/10 HP, 1/2 HP, 115V 1/2 HP, 1 HP, 230V 1 HP, 460V, 3 5-9 2 w/90 elbow stainless steel 20', SJOW, 16 AWG stainless steel stainless steel mechanical carbon & ceramic
20
40
60
80
100
120
140
0 160
F EATURES
Pumps up to 145 GPM (1 HP), 114 GPM (1/2 HP) and 103 GPM (4/10 HP) Designed for reliable pumping of wastewater Stainless steel, corrosionresistant shaft and hardware Oil-cooled and lubricated, continuous-duty PSC motors Silicon carbide or carbon ceramic mechanical seals Tethered float switches feature piggyback controls 20 power cord Suitable for continuous use Includes 90 discharge elbow CSA Listed
PAGE 39
M9035SSE
40
DSW100
DSW
605.6 13.7 12
SEWAGE PUMPS
SR1830
Applications Capacities Shut-off head Solids handling Liquids handling
95 GPM 19 2 up to 140F
16 12 8
SRM4
4/10
HP
4 3 2
septic effluent and sewage 4/10 HP, shaded pole, 115V, 12A, 1, 60Hz 5-9 2 heavy cast iron 10 (20 optional) recessed, thermoplastic cast iron type 11A, carbon & ceramic 50.8 mm
4 0
Intermittent liquid temp. Motor electrical data Acceptable pH range Discharge NPT Housing Power cord Impeller Volute case Shaft seal
10
20
30
40
50
60
70
80
90
Pump Only
F EATURES
Complete package for versatile applications Residential septic tank sewage Large sumps High-quality system includes SRM4AIC sewage pump 4/10 HP, 115V, 12A, 1, 60Hz motor 2 diameter discharge Oil-filled motor for imum heat dissipation max and continuous bearing lubrication Recessed vortex impeller for free flow of solids up to 2 diameter Rotary shaft seal has carbon and ceramic faces for positive seal Thermal overload protection with automatic reset CSA Listed Basin: 18 x 30 structural foam construction 30-gallon capacity 4 plastic slip type or cast iron inlet hub Sealed Cover: 18 solid structural foam cover with 2 discharge flange, vent flange suitable for 2 or 3 vent, or split steel with 2 or 3 vent Check Valve: 2 full swing Fully Assembled: Includes discharge pipe inside basin Available in IAPMO approved models
PAGE 40
M9036 SSE
20
SEWAGE PUMPS
CMV1830
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head 18 shut-off: 19 shut-off: Solids handling Liquids handling
15 4 10
360 LPM
CMV
51
/2 H
P
2
50.8 mm
5 1 0 0 100
raw sewage, effluent and drain water up to 140F up to 60C 1/2 HP, PSC, 1625 RPM, 115V, 12A, 1, 60Hz 6-9 2 50.8 mm
10
20
30
40
50
60
70
80
90
Intermittent liquid temp Motor electrical data Acceptable pH range Discharge, NPT
Pump Only
F EATU RES
Complete package for versatile applications includes: CMV5A-11 sewage pump 1/2 HP, 115V, 12A, 1, 60Hz Oil-filled motor for maximum heat dissipation and continuous bearing lubrication Recessed vortex impeller provides minimal radial loading for long bearing life Wide-angle mercury-free mechanical float switch for maximum drawdown Recessed vortex impeller operates completely out of volute and provides free flow through passage for solids and liquids Basin: 18 x 30 structural foam construction 30-gallon capacity 4 plastic slip type or cast iron inlet hub Sealed Cover: 18 solid structural foam cover with 2 discharge flange, vent flange suitable for 2 or 3 vent, or split steel with 2 or 3 vent Check Valve: 2 full swing
PAGE 41
M9037SSE
SEWAGE PUMPS
SRM-BP
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Solids handling Liquids handling
16 12 8
SRM4
4/10
HP
4 3 2
septic effluent and sewage 4/10 HP, PSC, 115V, 12A, 1, 60Hz 50.8 mm
4 0
Intermittent liquid temp. Motor electrical data Acceptable pH range Discharge NPT Housing Power cord Impeller Volute case Shaft seal Basin size
10
20
30
40
50
60
70
80
90
Pump Only
recessed, thermoplastic cast iron type 11A, carbon & ceramic 24 x 24 structural foam construction
F EATURES
Power for versatile applications Residential septic tank sewage Large sumps Long-lasting performance Oil-filled motor for maximum heat dissipation and continuous bearing lubrication Recessed vortex impeller for free flow of liquids, solids up to 2 diameter Rotary shaft seal has carbon and ceramic faces for positive seal Thermal overload protection with automatic reset Pump is pre-installed in basin, with integral torque stops to ensure stability Available with alarm, optional Basin: Stackable design allows for compact inventory Integral 360 top grip for easy lifting and handling in tight spaces 24 x 24 structural foam construction; 45-gallon capacity Shallow 24 deep basin reduces installation time for digging pit Anti-floatation features include concrete splash lip and unique basin shape to keep the system from floating or becoming un-installed Concrete-proof cover insert protects the system from damage during rough-in and masonry work E-Z Switch rod allows removal of float switch without disassembling basin lid, or handling pump or plumbing. Additional clip for secondary float included; float sold separately
PAGE 42
M9161 SSE
20
SEWAGE PUMPS
CMV-BP
Applications Capacities Shut-off head 18 shut-off: 19 shut-off: Solids handling Liquids handling
360 LPM
15 4 10
CMV
51
/2 H
P
2
50.8 mm
5 1 0 0 100
raw sewage, effluent and drain water up to 140F up to 60C 1/2 HP, PSC, 1625 RPM, 115V, 12A, 1, 60Hz 6-9 2 cast iron 20, 16/3, SJTW recessed, thermoplastic thermoplastic type 11A, carbon & ceramic 24 x 24 structural foam construction 50.8 mm
10
20
30
40
50
60
70
80
90
Intermittent liquid temp Motor electrical data Acceptable pH range Discharge, NPT Housing Power cord Impeller Volute case Shaft seal Basin size
Pump Only
F EATU RES
Engineered for many years of maintenance-free operation Wide-angle, mercury-free mechanical float switch for maximum drawdown Recessed vortex impeller operates completely out of volute and provides free flow through passage for solids and liquids Durable motor will deliver many years of reliable service Available with alarm, optional Oil-filled motor for maximum heat dissipation and continuous bearing lubrication Recessed vortex impeller provides minimal radial loading for long bearing life Pump is pre-installed in basin, with integral torque stops to ensure stability Basin: Stackable design allows for compact inventory Integral 360 top grip for easy lifting and handling in tight spaces 24 x 24 structural foam construction; 45-gallon capacity Shallow 24- deep basin reduces installation time for digging pit Anti-floatation features include concrete splash lip and unique basin shape to keep the system from floating or becoming un-installed Concrete-proof cover insert protects the system from damage during rough-in and masonry work E-Z Switch rod allows removal of float switch without disassembling basin lid, or handling pump or plumbing. Additional clip for secondary float included; float sold separately
PAGE 43
M9162SSE
SEWAGE PUMPS
MW-BP
Applications Capacities Shut-off head Solids handling Liquids handling
20
MW5
15 10 5 0
0 1/ 2 HP
domestic sewage and drain water 1/2 HP, 1625 RPM, PSC (1), oil-filled, 115V, 9A, 1, 60Hz; 230V, 4.5A, 1, 60Hz 5-9 2 cast iron 20, 16/3, SJTW thermoplastic class 30 cast iron type 6, carbon & ceramic 24 x 24 structural foam construction 50.8 mm
Intermittent liquid temp. Motor electrical data Acceptable pH range Discharge NPT Housing Power cord Impeller Volute case Shaft seal Basin size
20
40
60
80
100
120
0 140
Pump Only
F EATURES
Fully assembled; pump is pre-installed in basin, with integral torque stops to ensure stability Oil-filled motor for maximum heat dissipation and continuous bearing lubrication Recessed vortex impeller for free flow of liquids, solids up to 2 diameter Available with alarm, optional Basin: Stackable design allows for compact inventory Integral 360 top grip for easy lifting and handling in tight spaces 24 x 24 structural foam construction; 45-gallon capacity Shallow 24- deep basin reduces installation time for digging pit Anti-floatation features include concrete splash lip and unique basin shape to keep the system from floating or becoming un-installed Concrete-proof cover insert protects the system from damage during rough-in and masonry work E-Z Switch rod allows removal of float switch without disassembling basin lid, or handling pump or plumbing. Additional clip for secondary float included; float sold separately
PAGE 44
M9178 SSE
SEWAGE PUMPS
MRJ
Capacities
95 GPM 19 2 up to 140F
16
Shut-off head Solids handling Liquids handling Intermittent liquid temp Motor electrical data Acceptable pH range Discharge, NPT Housing Power cord Impeller Volute case Shaft seal
MRJ
12 8 4 0
4 3 2 1
septic effluent and sewage 4/10 HP, shaded pole, 115V, 12A, 1, 60Hz; 230V, 6A, 1, 60Hz 5-9 2 heavy cast iron 10 (20 optional) recessed, thermoplastic cast iron type 11A, carbon & ceramic 50.8 mm
10
20
30
40
50
60
70
80
90
Pump Only
F EATU RES
Sewage Ejector Pump Up Package Includes: SRM4S-1 (115V) 4/10 HP sewage pump Myers poly tank 2 check valve/discharge piping assembly Ideal for basements, room additions, factories and warehouses Simple installation Accommodates toilet, vanity or humidifier Fits almost anywhere Use with nearly any toilet style Concrete floor stays intact; no need to destroy flooring since the Ready Jon can be installed freestanding on top of any level surface Tank and piping can be hidden behind a wall
PAGE 45
M9038SSE
Applications
basement bathroom
TOTAL HEAD IN FEET
20
GRINDER PUMPS
MRG20
Applications Capacities Shut-off head Liquids handling
100 80 60 40 20 0 0 10
MRG20
2 HP
30 25 20 15 10 5
Intermittent liquid temp. Winding Motor electrical data Acceptable pH range Discharge NPT Sump diameter duplex Motor housing Power cord Impeller Shaft seal (Optional) Impeller Power cord Pump, motor shaft Min. sump diameter Simplex: Duplex:
2 HP, 3450 RPM, 1 - capacitor start/run 230V; 60Hz, 15A 6-9 1-1/4 36 cast iron 20 eng. thermoplastic carbon & ceramic tungsten carbide thermoplastic 20 stainless steel (416 SS) 24 36 61.0 cm 91.4 cm 31.75 mm 91.4 cm
20
30
40
50
60
70
80
F EATURES
The MRG20 Series features a patented cutter mechanism and recessed impeller design to effectively macerate typical sewage solids into fine slurry Durable motor will deliver many years of reliable service Oil-filled motor for maximum heat dissipation and constant bearing lubrication Recessed impeller reduces radial bearing loads and increases bearing life High-torque capacitor starts single-phase motor for assured starting under heavy load; no external capacitor needed Heavy-duty 2 HP listed, wide-angle float switch On-winding current and temperature-sensitive overload The MRG20 is designed for easy maintenance Shredding ring and grinder impeller are replaceable without dismantling pump or motor (440 Stainless Steel, 58-60 Rockwell) 300 Series Stainless Steel fasteners CSA Listed
PAGE 46
M9039 SSE
120
GRINDER PUMPS
Pump
Basin Cover Guide rails Floats Control panel Junction box Inlet fittings Outlet
* Pump and inlet hub shipped separately must be field installed. Wiring connections to be made by qualified electrician. Concrete anti-flotation base requires 2 cu. ft. for each foot of basin depth.
F EATURES
System Benefits: Eliminate guesswork of selecting components No mismatched or improperly fitting parts Easy installation installer only has to excavate, secure, connect discharge lines, locate and mount inlet hub, locate and mount panel, install pump in basin and connect electrical wiring Inside Packages: Simplex 30 x 36: MRG20 2 HP grinder pump 230V, 1 30 x 36 FRP basin Steel cover Two SDR-35 inlet hubs and Sch. 40 adapters Wide-angle on/off float switch and a mercury alarm float switch Check valve Outside Packages: Simplex 24: MRG20 2 HP grinder pump 230V, 1 Basin, FRP 24 x 5 24 x 6 24 x 7 24 x 8 Polypropylene cover Two SDR-35 inlet hubs and Sch. 40 adapters Quick-disconnect rail system with stainless steel rails, check valve and ball valve Wide-angle on/off float switch and a mercury alarm float switch NEMA 4X junction box
PAGE 47
M9040SSE
GRINDER PUMPS
MRGD200/MRGD200 -Retrofit
2 HP Double Seal Grinder Pump for Residential Applications
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
120
Applications Capacities Shut-off head Liquids handling Continuous liquid temp. Motor electrical data
90
25 20
60 15 10 5 0
30
2 HP, dry-wound, capacitor start/capacitor run, thermal overload protected, 230V, 1, 60Hz, 13.4 FLA; 230/460V, 3, 60Hz, 8.2/4.1 FLA 5-9 1-1/4 36 cast iron cast iron, 10 vane 20 dual mechanical seal stainless steel stainless steel, 440C hardened to 55 - 60 Rockwell C, dual cutters float switch optional 31.75 mm
15
30
45
60
Acceptable pH range Discharge NPT Sump diameter duplex Motor housing Impeller Power cord Shaft seal standard Pump, motor shaft Cutters Operations
Pump Only
F EATURES
2 HP; single-phase, 230V; 3-phase, 230/460V Superior grinding capabilities High-torque, capacitor start/capacitor run motor Dry-wound motor, better efficiency and serviceable, thermal overload protected Temperature rated at 105F (41C) Dual shaft seals silicon carbide/silicon carbide and carbon/ceramic Dual cutter design stainless steel Cast iron 10-vane impeller Upper and lower shielded ball bearings Retrofittable with ALL major competitors Double-cord strain relief Replaceable 20 (6 m), jacketed SOW power cord 16 AWG (1 phase) 14 AWG (3 phase) Retrofit package is completely assembled, ready to drop-in-place replacement package
PAGE 48
M9041 SSE
D MRG 200 2H P
GRINDER PUMPS
MRGD2
00 2 H P
30 25 20 15 10 5
Pump
Basin Cover Guide rails Floats Control panel Junction box Inlet fittings Outlet
F EATURES
Package: Pre-assembled package. To install, simply slide pump assembly down guide rail system, connect plumbing and electrical service and system is ready to go Pump: Effectively macerates typical domestic sewage solids into a fine slurry Cover: Rated to withstand momentary loads of residential lawn equipment Guide Rails: Package includes pre-assembled cast iron discharge elbow, discharge flanges, steel spacer, Stainless Steel upper guide rail bracket and lift chain. Also includes bronze gate valve and ball check valve Junction Box: Allows for simple electrical connections, easy service access and protection of connections
PAGE 49
M9042SSE
WASTEWATER PUMPS
3MW Series
S SP PECIFICATI PE E CIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Solids handling 1750 RPM: 3450 RPM: Liquids handling Intermittent liquid temp. Available motor (single phase are PSC type; three phase need Myers control panel) Acceptable pH range Discharge Sump diameter duplex Motor housing Power cord Shaft seal (Optional)
15 90
30
21
330 GPM 92 2-1/2 2 140F 1750 RPM 1-1/23 HP 208/230V, 1, 60Hz 208/230/460/575V, 3, 60Hz 6-9 3 NPT (vertical) 48 cast iron 25, SOW/SOWA
3450 RPM
18 15 12 9
1750 RPM
240 280 320 360
6 3
21
1.2 m
3450 RPM
18 15 12 9 6 3 200
F EATURES
High-efficiency hydraulic design Two-vaned rounded port impellers Offered in two speeds Hydraulic end virtually maintenance-free Volute seal ring replaceable in minutes Durable motor for reliable service Oil-filled motor for constant bearing lubrication High-torque, permanent split capacitor (PSC), single- phase motors; no starting switches or relays Optional seal leak probe (dual seal motors only) Current and temperature overload (single phase only) CSA Listed
PAGE 50
M9044 SSE
24
80
24
WASTEWATER PUMPS
3WHV Series
S SPE PECIFICATI PECIFICATIONS CIFICATI ONS
Applications Capacities Shut-off head Solids handling Liquids handling Intermittent liquid temp. Available motor Acceptable pH range Discharge Sump diameter duplex Motor housing Power cord Shaft seal (Optional)
60
500
1500
2000 18 16 14
40 30 20 10 0
raw unscreened sewage, rain water, effluent up to 140F up to 60C 1750 RPM; 1-1/25 HP, 230V, 1, 60Hz; 208/230/460/575V, 3, 60Hz 6-9 3 (flanged) 60 cast iron 25, SOW/SOW-A single type 21, carbon & ceramic tungsten carbide 76.2 mm 1.5 m
2" I 6" I MP. DIA. MP. D 3 IA. 3 WHV30M W HV 20M4 4 3 HP 5-1/ 2" I M 2 HP P. DIA . 3WH V15M4 1-1/2 H P
0 100 200 300 400 500
6-1/
HV50 M4 5 HP
12 10 8 6 4 2
F EATURES
High-volume capacity for commercial use Apartments, condominiums, restaurants, shopping centers, motels, rest stops, campgrounds, offices, hospitals and more Sewage collection systems and treatment plants Durable motor for long-lasting performance 1-1/2, 2, 3 & 5 HP models Oil-filled for maximum heat dissipation and constant bearing lubrication On-winding overload (1) protects motor High-efficiency hydraulics Two-vane rounded port impellers pass 2-1/2 solids with ease CSA Listed
PAGE 51
M9045SSE
50
6-3/4
" IM P. DIA . 3W
Pro-Source Pumper
100 80 60 40
HP E DP55
RV
30
20
4-cycle PowerPro gasoline engine reinforced corrosion resistant thermoplastic polymer viton mechanical viton 300 grade stainless steel
F EATURES
Rugged, light-weight design is ideal for applications where electrical power is not available Corrosion-resistant composite pump construction Automatic low-oil safety cut, manual throttle, choke and shut-off controls Built-in check valve Securely mounted within a rugged steel-framed roll cage thats coated for corrosion resistance Equipped with noisedampening, non-slip rubber feet Chemical resistant viton seals; o-rings with stainless steel fasteners Suction lift capability of 25 Accessories: 15 Suction Hose Kit: built-in 2 NPTF swivel fitting and 2 NPTM fitting for easy hookup; coil-reinforced wall prevents collapse; includes aluminum suction screen to prevent debris from reaching pump 25 Discharge Hose Kit: built-in 2 NPTF swivel fitting and 2 NPTM fitting for easy hookup; collapsible for easy roll-up and storage; reinforced wall adds durability
PAGE 52
M9203 SSE
5-1/2
EPP Series
EPP
40 30 20 10 0
-ME
EPP-
50S
14
ME45
-11
EPP-S
MC-1
1/2
12
SM33
1 1/ 2H
HP
10 8 6 4 2 0
IM1C
1/3 H
10
20
30
40
50
60
70
80
90
100
SSM33
ME45
ME50
F EATURES
The PENTEK EPP Series Elevator Pump Control System is approved for oil/ water detection in applications where oil and hydrocarbons are prohibited from being released into the environment. The system is designed to provide pumping, monitoring and alarm in garages, elevator sump pits, transformer vaults and substations. The elevator pump control activates the pump for removal of water from elevator pits in accordance with ASME17.1. The control will also shut down the pump before discharging harmful substances. Control panel with separate pump and control circuits, NEMA 1 Enclosure; 8.75H x 6.5W x 5D Plug-in for quick and easy installation Remote alarm Multiple indicator lights: power on, pump run, high water, and high oil indicators One pre-set sensor for easy installation, no field adjustment necessary UL and CSA listed Elevator Pump Control Complete Packaged System: 1/3 or 1/2 HP, 115V sump/effluent pump Remote alarm Easy clamp-mount installation, with plug-in ready wiring Compliant with ASME 17.1 and local building and safety codes Control Operation On water rise, fluid level reaches pump start probe to activate the pump. Pump remains on until fluid level is below the off probe. The off probe senses air or oil and turns the pump off so the oil layer (if present) will not be pumped out of the sump. If the liquid level reaches thealarm probe and mechanical float, the system will differentiate between water and oil and activate the remote alarm.
PAGE 53
M9202SSE
ACCESSORIES
1-1/4" to 3" Lift-out Rail Systems for Sewage, Effluent and Grinder Pumps
1-1/2" x 2" Galv/SST cast iron cast iron SST Buna-N 3/4" SST TRS-75 Galv/SST
2" x 2" Galv/SST cast iron cast iron SST Buna-N 3/4" SST TRS-75 Galv/SST SST=Stainless Steel
3" x 3" Galv/SST cast iron cast iron SST Buna-N 3/4" SST TRS-75 Galv/SST
2" x 3" Galv/SST cast iron cast iron SST Buna-N 3/4" SST TRS-75 Galv/SST
Note: SRAX-125 package available for Class 1, Division 1, Groups C and D installations.
F EATURES
Lift-out rail system offers ease of service and reinstallation Eliminates need to disassemble piping to remove pump No need for personnel to enter basin when service is required Offered with or without check valve Dual rail guides pump to automatic leak-proof connection and to the surface Handles 1-1/4 to 3 discharge pumps Corrosion-resistant construction for long life and ease of service Heavy-duty cast iron construction Positive machine fit with O-ring seal Choice of galvanized or stainless steel brackets for sewage or effluent service ensures parts will not corrode together System Includes: Mounting base Lift-out elbow with check valve Guide plate Fasteners and O-rings
PAGE 54
M9073 SSE
ACCESSORIES
F EATURES
Quality electrical components assure reliable automatic pump operation For 1/4 7 HP sump, sewage and effluent pumps IEC horsepower-rated contactors (1) and motor starters (3) 3 starters with ambient-compensated quick-trip overloads Includes alternating and override relays to maximize pump wear Designed for use with off-on alarm (simplex) and off-on lag-alarm (duplex) mercury switches (not included with panel) Corrosion resistant for long life Weathertight NEMA 4X fiberglass enclosure with outdoor panels Indoor NEMA 1 panels are enamel-coated galvanized steel Meets NEC safety standards UL-508 approved panel designs Outdoor NEMA 4X panels include standard high water alarm light Indoor NEMA 1 panels include standard high water alarm buzzer Wide range of panel options: Elapsed time meter Alarm bell or horn Alarm bell or horn with silence switch Auxiliary contacts Condensation heater Convenience outlet Intrinsically safe relays Lightning arrestor Full inner door Cycle counter 24V control circuitry Transfer switch/generator receptacle Pump delay circuitry Low level cut-off and alarm Phase loss circuitry Low voltage circuitry Note: Additional options available
PAGE 55
M9073SSE
ACCESSORIES
Level Controls
F EATURES
PAGE 56
M9073 SSE
ACCESSORIES
Includes three power modes: Works during power failure* - 120V power source - 9V battery source* (battery not included) - 120V with 9V back-up* *Model SA-1 Only
CV-200P and CV-300P (not shown) CV-200 and CV-300 (not shown)
Cast iron 2 and 3 check valves with NPT threaded connections
Size range meets many pump applications 18 x 30 structural foam basins; cast iron or flexible inlet hubs; one- or two-piece structural foam covers; 2 or 3 discharge, 2 or 3 vent IAPMO-approved
18 x 30 polypropylene basins; steel one- or two-piece covers; 2 or 3 discharge, 2 or 3 vent; 4 cast iron or flexible inlet hubs 24 x 36 and 30 x 48 FRP fiberglass basins
Steel cover with separate simplex or duplex pump covers; 2 or 3 discharge, 2 or 3 vent
PAGE 57
M9073SSE
NOTES
PAGE 58