Documente Academic
Documente Profesional
Documente Cultură
00
RE 18 136-05/05.00
Type YKE1.A/C
Overview of contents
Contents Features Ordering details Function, section, symbol Technical data Characteristic curves, performance limits Unit dimensions, cavity Page 1 1, 2 2 3 4 5
Features
Direct operated directional spool valve with solenoid actuation Flow can be passed in both directions Wet pin DC solenoids Rotatable solenoid coil With protected hand override
Ordering details Y
Cartridge Spool valve Electrical Standard 350 bar Nominal size
Pressure
N9
No code = FKM seals Without plug-in connector 2) Coil junior timer (on request) Protected hand override 24 V DC Wet pin DC solenoid, with removable coil Series
=Y =K =E = No code =1
No. of Symbols
2 4
K4 = C4 = N9 = G24 = C= A=
1) 2)
Cavity
1)
350 bar
connections 4
qV = L/min
=D
1
2
See page 5 Plug-in connectors must be ordered separately (see page 2) Type YKE1DA/CG24N9K4 YKE1EA/CG24N9K4 YKE1FA/CG24N9K4
3
4
T-31A
50
1 2 3
=E
4
=F
1 3
YKE1
1/6
RE 18 136-05/05.00
Ordering details: plug-in connectors to DIN 43 650 A and ISO 4400 for component plug "K4"
Further plug-in connectors see RE 08 006
Material No.
With indicator light 12 240 V 00057292 With indicator light and Z-diode protective circuit 24 V 00310995
The various symbols are obtained by using the appropriate spool (D; E and F). Ports 1, 2 and 3 can be, continuously, applied with an operating pressure of 350 bar and the flow can be passed in both directions (see symbols). The hand override (10) makes it possible to switch the valve without energising the solenoid. Preferrably port 3 is to be used as the pump connection, ports 2 and 4 for the actuators and port 1 as the tank connection.
Symbol "E":
5 10
1 2 9 3 4 8 7
Rexroth Hydraulics
2/6
YKE1
RE 18 136-05/05.00
Technical data (for applications outside these parameters, please consult us!)
General
Installation Ambient temperature range Weight C kg Optional 30 to + 50 0.6
Hydraulic
Maximum operating pressure Maximum flow Pressure fluid FKM seals Pressure fluid temperature range Viscosity range Degree of contamination C mm2/s bar L/min 350 50 Mineral oil (HL, HLP) to DIN 51 524; Fast bio-degradable pressure fluids to VDMA 24 568 (also see RE 90 221); HETG (rape seed oil); HEPG (polyglycol); HEES (synthetic ester); other pressure fluids on request 20 to + 80 (with FKM seals) 2.8 to 500 Maximum permissible degree of contamination of the pressure fluid is to NAS 1638 class 9. We, therefore, recommend a filter with a minimum retention rate of 10 75.
Electrical
Voltage type Available voltage
1)
Voltage tolerance (nominal voltage) Power consumption Duty Switching time to ISO 6403 (solenoid horizontal) Switching frequency Protection to DIN 40 050 Maximum coil temperature
1) 2)
cycles/h C
150 When connecting the electrics, the protective conductor (PE must be connected according to the relevant regulations. )
Further voltages on request. Due to the occuring surface temperature of the solenoid coils, please observe the European standards EN563 and EN982!
YKE1
3/6
Rexroth Hydraulics
RE 18 136-05/05.00
YKE1D 21
YKE1F 34
YKE1F 21
20
30
40
20
30
40
Flow in L/min
Flow in L/min
Flow in L/min
Flow over two control lands and with pre-opening of the tank 3 4 / 2 1
350
YKE1E
50
60
Rexroth Hydraulics
4/6
YKE1
RE 18 136-05/05.00
Dimensions in mm
6
05
9 10 5
1 2 3 4 5 6 7 8 9 10
21,11** 21,21
8
LS stop
Actuator connection 1 Actuator connection 2 Actuator connection 3 Actuator connection 4 Plug-in connector to DIN 43 650 must be ordered separately, see page 2 Space required to remove the plug-in connector Protected hand override 24 A/F; tightening torque, MA = 45 to 50 Nm Dim. for plug-in connector without circuitry Dim. ( ) for plug-in connector with circuitry
0,8 Recommended distance from the surface (with spot face)
86,6
68
30
4
0,000 LS
32,0 32,1
3,96 12,7 Min. distance for area with full threads 18,54** 18,64 29,72 17,70** 17,75 52,71
A 20,68
20,62
0,000
85
4
14,3
21,44
3
14,3
45,24
2
75,95 85,12 85,22
68,28
max. 0,25 x 45
1
11,9
Free area for solenoid 39 mm Min. spacing (central axis to the central axis of an identical cavity)
General dimensional tolerances 0.05 A ** Concentricity 0.2 mm One pos. (X,X) 0.1 mm Two pos. (X,XX) 1/2 Angular tolerance 1,6 Surface finish 0,5 Corner radius
YKE1
5/6
Rexroth Hydraulics
RE 18 136-05/05.00
Notes
Mannesmann Rexroth AG Rexroth Hydraulics D-97813 Lohr am Main Jahnstrae 3-5 D-97816 Lohr am Main Telefon 0 93 52 / 18-0 Telefax 0 93 52 / 18-23 58 Telex 6 89 418-0 E-Mail product.support@rexroth.de Internet www.rexroth.com
Mannesmann Rexroth Limited Cromwell Road, St Neots, Cambs, PE19 2ES Tel: 0 14 80/22 32 56 Fax: 0 14 80/21 90 52 E-mail: info@rexroth.co.uk
The specified data is for product description purposes only and may not be deemed to be guaranteed unless expressly confirmed in the contract.
6/6
YKE1