Documente Academic
Documente Profesional
Documente Cultură
3-1
Objectives
Upon completion of this chapter, you will be able to perform the following tasks:
Identify and connect necessary components to enable connectivity between routers or switches Identify and connect necessary components to enable WAN connectivity over serial or ISDN BRI connections Set up console connections between routers, switches and a terminal
2000, Cisco Systems, Inc.
www.cisco.com
ICND v1.0a3-2
ISDN Cloud
www.cisco.com
ICND v1.0a3-4
802.3
10BaseF 802.3u Specifications for 100MB (Fast) Ethernet
ICND v1.0a3-5
Physical
DIX Standard
www.cisco.com
Access
Provides connectivty between the end user device and the access switch. Not typically used at this layer.
Layer
Core Layer
Core Layer
www.cisco.com
ICND v1.0a3-6
www.cisco.com
ICND v1.0a3-7
www.cisco.com
ICND v1.0a3-8
UTP Device
Wire Pair T is Tip R is Ring Pair 3 T2 Pair 3 R2 Pair 2 T3 Pair 1 R1 Pair 1 T1 Pair 2 R3 Pair 4 T4 Pair 4 R4
Pin 1 2 3 4 5 6 7 8
www.cisco.com
ICND v1.0a3-9
Hub/Switch
Server/Router
Pin 1 2 3 4 5 6 7 8
Pin 1 2 3 4 5 6 7 8
w g w b w o w br g o b br
w g w b w o w br g o b br
Crossover Cable
br w g w b w o w br g o b
w ww w br b g br o b
o g
1x
2x
3x
4x
1x
2x
3x
4x 1x
2x
3x
4x
Use a crossover cable when BOTH ports are designated with an x or neither port is designated with an x.
2000, Cisco Systems, Inc.
www.cisco.com
ICND v1.0a3-12
www.cisco.com
ICND v1.0a3-13
Core_ Server
ISDN Cloud
www.cisco.com
ICND v1.0a3-14
www.cisco.com
ICND v1.0a3-15
DCE
EIA/TIA-232
EIA/TIA-449
V.35
X.21
EIA-530
DCE
S
S S
DTE
DCE
DCE
DTE
www.cisco.com
ICND v1.0a3-17
Fixed Interfaces
www.cisco.com
ICND v1.0a3-18
Modular Interfaces
Serial WAN ports can be modular
1603 Routerrear view
WAN Interface Card
Ethernet 10BaseT
Ethernet AUI
Console
Module
www.cisco.com
ICND v1.0a3-19
www.cisco.com
ICND v1.0a3-20
!!!WARNING!!!
Do not connect a cable into an ISDN port unless it is from an ISDN switch or ISDN wall jack. If you connect a cable from any other device into the BRI port, you will ruin the non-ISDN device.
www.cisco.com
ICND v1.0a3-21
PCs require an RJ-45 to DB-9 or RJ-45 to DB-25 adapter COM port settings are 9600 bps, 8 data bits, no parity, 1 stop bit, no flow control This provides out-of-band console access AUX switch port may be used for modem-connected console
2000, Cisco Systems, Inc.
www.cisco.com
ICND v1.0a3-22
Visual Objective
wg_pc_a console console e0/2 (2x) e0 s0 wg_sw_a wg_ro_a bri0
A/B
fa0/26 (Ax)
e0/1 (1x)
LL/FR
wg_sw_l
...
fa0/24 (24x) fa0/1 (1x) fa0/12 (12x) fa0/23 (23x)
ISDN
s3/0 fa0/0
core_ server
2000, Cisco Systems, Inc.
core_sw_a
www.cisco.com
core_ro
ICND v1.0a3-23
Summary
After completing this chapter, you should be able to perform the following tasks:
Identify and connect necessary components to enable connectivity between switches and routers Identify and connect necessary components to enable WAN connectivity between over serial or ISDN BRI connections
www.cisco.com
ICND v1.0a3-24
Review Questions
1. Discuss three standards on which Ethernet LAN implementations are based. 2. If you want to upgrade your switch to switch connectivity to 100BaseT, what category of cable do you need? 3. Does the following pinout scheme reflect a straight-through, rollover, or crossover cable?
1 8
w o w w b g w br 0 g b br
w g w w b o w br g o b br
B
2000, Cisco Systems, Inc.
C
ICND v1.0a3-25
www.cisco.com