Documente Academic
Documente Profesional
Documente Cultură
KMF0711129CE
Personal Facsimile
Model No. KX-FT932BR-B
B: Black Version (for Brazil)
2007 Panasonic Communications Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
KX-FT932BR-B
TABLE OF CONTENTS
PAGE 1 Safety Precautions ----------------------------------------------- 3 1.1. For Service Technicians ----------------------------------3 1.2. AC Caution---------------------------------------------------4 1.3. Personal Safety Precautions ----------------------------5 1.4. Service Precautions ---------------------------------------6 2 Warning -------------------------------------------------------------- 7 2.1. About Lead Free Solder (PbF: Pb free) --------------7 2.2. Insulation Resistance Test -------------------------------7 2.3. Battery Caution ---------------------------------------------7 3 Specifications ------------------------------------------------------ 8 4 General/Introduction --------------------------------------------- 9 4.1. Optional Accessories--------------------------------------9 4.2. Translation Lists --------------------------------------------9 5 Features ------------------------------------------------------------ 10 6 Technical Descriptions ---------------------------------------- 11 6.1. Connection Diagram------------------------------------- 11 6.2. General Block Diagram --------------------------------- 12 6.3. Control Section ------------------------------------------- 14 6.4. Facsimile Section ---------------------------------------- 20 6.5. Sensors and Switches ---------------------------------- 26 6.6. Modem Section ------------------------------------------- 30 6.7. NCU Section----------------------------------------------- 37 6.8. ITS (Integrated Telephone System) and Monitor Section ------------------------------------------- 41 6.9. ATAS (Automatic Telephone Answering System) Section ------------------------------------------ 41 6.10. Operation Board Section ------------------------------- 43 6.11. LCD Section ----------------------------------------------- 44 6.12. Power Supply Board Section-------------------------- 45 7 Location of Controls and Components ------------------ 48 7.1. Overview --------------------------------------------------- 48 7.2. Control Panel---------------------------------------------- 49 8 Installation Instructions --------------------------------------- 50 8.1. Installation Space ---------------------------------------- 50 8.2. Connections ----------------------------------------------- 50 8.3. Installing the Recording Paper------------------------ 51 9 Operation Instructions ---------------------------------------- 52 9.1. Setting Your Logo ---------------------------------------- 52 10 Test Mode ---------------------------------------------------------- 54 10.1. DTMF Single Tone Transmit Selection ------------- 55 10.2. Button Code Table --------------------------------------- 55 10.3. Print Test Pattern ----------------------------------------- 55 11 Service Mode ----------------------------------------------------- 56 11.1. Programming and Lists --------------------------------- 56 11.2. The Example of the Printed List ---------------------- 60 12 Troubleshooting Guide---------------------------------------- 64 12.1. Troubleshooting summary ----------------------------- 64 12.2. Error Messages-Display -------------------------------- 65 12.3. Error Messages Report --------------------------------- 66 12.4. Remote Programming----------------------------------- 88 12.5. Troubleshooting Details -------------------------------- 91 13 Service Fixture & Tools ------------------------------------- 117 14 Disassembly and Assembly Instructions ------------- 118 14.1. Disassembly Flowchart --------------------------------118 14.2. Disassembly Procedurel------------------------------ 120 15 Maintenance ---------------------------------------------------- 129 15.1. Maintenance Items and Componet Locations -- 129 15.2. Gear Section -------------------------------------------- 131 16 PAGE 15.3. Jams ------------------------------------------------------- 137 15.4. Cleaning--------------------------------------------------- 138 Miscellaneous -------------------------------------------------- 139 16.1. Terminal Guide of ICs Transistors and Diodes -- 139 16.2. How to Replace the Flat Package IC -------------- 141 16.3. Test Chart ------------------------------------------------ 143 Schematic Diagram ------------------------------------------- 146 17.1. Digital Board --------------------------------------------- 146 17.2. Analog Board -------------------------------------------- 148 17.3. Operation Board ---------------------------------------- 150 17.4. Power Supply Board ----------------------------------- 151 Printed Circuit Board ----------------------------------------- 153 18.1. Digital Board --------------------------------------------- 153 18.2. Analog Board ------------------------------------------- 155 18.3. Operation Board ---------------------------------------- 157 18.4. Power Supply Board ----------------------------------- 159 Appendix Information of Schematic Diagram ------- 160 Exploded View and Replacement Parts List ---------- 162 20.1. Cabinet, Mechanical and Electrical Parts Location --------------------------------------------------- 162 20.2. Replacement Parts List ------------------------------- 168 20.3. Cabinet and Mechanical Parts ---------------------- 168 20.4. Digital Board Parts ------------------------------------- 169 20.5. Analog Board Parts ------------------------------------ 171 20.6. Operation Board Parts--------------------------------- 172 20.7. Power Supply Board Parts --------------------------- 172 20.8. Fixtures and Tools -------------------------------------- 173
17
18
19 20
KX-FT932BR-B
1 Safety Precautions
1. 2. 3. 4. 5. Before servicing, unplug the AC power cord to prevent an electric shock. When replacing parts, use only the manufacturer's recommended components. Check the condition of the power cord. Replace if wear or damage is evident. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc. Before returning the serviced equipment to the customer, be sure to perform the following insulation resistance test to prevent the customer from being exposed to shock hazards.
1.1.
ICs and LSIs are vulnerable to static electricity. When repairing, the following precautions will help prevent recurring malfunctions. 1. Cover the plastic parts boxes with aluminum foil. 2. Ground the soldering irons. 3. Use a conductive mat on the worktable. 4. Do not touch the IC or LSI pins with bare fingers.
1.1.1.
There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper, (Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the manufacturers specific instructions for the melting points of their products and any precautions for using their product with other materials. The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.
KX-FT932BR-B
1.1.2.
P.C.Boards marked as PbF use Pb Free solder. (See the figure below.) (Example:Digital board)
Note: The PbF marked may be found on different areas of the same P.C.Board,depending on manufacture date.
1.2.
AC Caution
For safety, before closing the lower cabinet, please make sure of the following precautions. 1. The earth lead is fixed with the screw. 2. The AC lead is connected properly to power supply unit. 3. Wrap the earth lead around the core 3 times. 4. Wrap the AC lead around the core 2 times.
KX-FT932BR-B
1.3.
1.3.1.
Be careful not to let your hair, clothes, fingers, accessories, etc., become caught in any moving sections of the unit. The moving sections of the unit are the rollers and a gear. There is a separation roller and a document feed roller which are rotated by the document feed motor. A gear rotates the two rollers. Be careful not to touch them with your hands, especially when the unit is operating.
1.3.2.
All the electrical sections of the unit supplied with AC power by the AC power cord are live. Never disassemble the unit for service with the AC power supply plugged in. CAUTION: AC voltage is supplied to the primary side of the power supply unit. Therefore, always unplug the AC power cord before disassembling for service.
KX-FT932BR-B
1.4.
1.4.1.
Service Precautions
Precautions to Prevent Damage from Static Electricity
Electrical charges accumulate on a person. For instance, clothes rubbing together can damage electric elements or change their electrical characteristics. In order to prevent static electricity, touch a metallic part that is grounded to release the static electricity. Never touch the electrical sections such as the power supply unit, etc.
KX-FT932BR-B
2 Warning
2.1. About Lead Free Solder (PbF: Pb free)
Note: In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that contains lead. We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn), Silver, (Ag), and Copper, (Cu).
This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair work we suggest using the same type of solder. Caution PbF solder has a melting point that is 50 ~ 70 F, (30 ~ 40C) higher than Pb solder. Please use a soldering iron with temperature control and adjust it to 700 20 F, (370 10C). Exercise care while using higher temperature soldering irons.: Do not heat the PCB for too long time in order to prevent solder splash or damage to the PCB. PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100F, (600C). When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the opposite side (See figure, below).
2.2.
1. Unplug the power cord and short the two prongs of the plug with a jumper wire. 2. Turn on the power switch. 3. Measure the resistance value with an ohmmeter between the jumpered AC plug and each exposed metal cabinet part (screw heads, control shafts, bottom frame, etc.). Note: Some exposed parts may be isolated from the chassis by design. These will read infinity. 4. If the measurement is outside the specified limits, there is a possibility of a shock hazard.
2.3.
Battery Caution
CAUTION Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers Instructions. The lithium battery is a critical component (type No. CR2032). Please observe for the proper polarity and the exact location when replacing it and soldering the replacement lithium battery in.
KX-FT932BR-B
3 Specifications
Applicable Lines: Document Size: Effective Scanning Width: Recording Paper Size: Effective Printing Width: Transmission Time*1: Scanning Density: Public Switched Telephone Network Max. 216 mm in width Max. 600 mm in length 208 mm 216 max. 30 m roll 208 mm Approx. 15 s/page (Original mode)*2 Horizontal: 8 pels/mm Vertical: 3.85 lines/mm - in standard resolution, 7.7 lines/mm - in fine/photo resolution, 15.4 lines/mm - in super fine resolution 64-level Contact Image Sensor Thermal printing Modified Huffman (MH), Modified READ (MR) 9,600 / 7,200 / 4,800 / 2,400 bps; Automatic Fallback 5 - 35C, 20 - 80% RH (Relative Humidity) Approx. height 121 mm width 352 mm depth 224 mm Approx. 2.7 kg Standby: Approx. 1.2 W Transmission: Approx. 13 W Reception: Approx. 30 W (When receiving a 20% black document) Copy: Approx. 35 W (When copying a 20% black document) Maximum: Approx. 120 W (When copying a 100% black document) 127 V AC, 60 Hz Approx. 28 pages of memory reception (Based on the ITU-T No. 1 Test Chart in standard resolution, with original mode.)
Photo resolution: Scanner Type: Printer Type: Data Compression System: Modem Speed: Operating Environment: Dimensions (HWD): Mass (Weight): Power Consumption:
* 1 Transmission speed depends upon the contents of the pages, resolution, telephone line conditions and capability of the other partys machine. * 2 Transmission speed is based upon the ITU-T No. 1 Test Chart with original mode. If the capability of the other partys machine is inferior to your unit, the transmission time may be longer. * 3 If an error occurs during fax reception, such as a paper jam or if the recording paper runs out, the fax and subsequent faxes will be retained in memory. Note: Design and specifications are subject to change without notice.
KX-FT932BR-B
4 General/Introduction
4.1. Optional Accessories
Item Standard thermal recording paper*1 Specifications/Usage 216 mm 30 m roll, with 25 mm core
*1 Use only the included or specified recording paper. Using other recording paper may affect print quality and/or cause excessive wear to the thermal head.
4.2.
4.2.1.
Translation Lists
Other
4.2.2.
KX-FT932BR-B
4.2.3.
5 Features
General LCD (Liquid Crystal Display) readout Facsimile Automatic document feeder (10 sheets) Resolution: Standard/Fine/Photo/Super Fine (64 level) Broad cast Integrated Telephone System Redialing function Phonebook function (100 names) Caller ID compatible** **Feature requires a subscription to caller identification services offered by certain local telephone companies for a tee. You and your caller(s) must be in areas that provide caller identification services, and compatible equipment must be used by both telephone companies. Feature not available when the unit is connected to a PBX system. Enhanced Copier Function 64-Level halftone
10
KX-FT932BR-B
6 Technical Descriptions
6.1. Connection Diagram
11
KX-FT932BR-B
6.2.
The following is an outline of each device IC on the digital board. (Refer to General Block Diagram (P.13).). 1. ASIC (IC1) Composed mainly of an address decoder and a modem control. Controls the general FAX operations. Controls the operation panel I/F. Controls the thermal head I/F and CIS I/F. Performs the image processing. CPU and Real time clock Provides the reset pulse for each of the major ICs. 2. Flash ROM (IC2) Contains all of the program instructions on the unit operations. This memory is used mainly for the parameter working in the storage area. 3. Dynamic RAM (IC4) This memory is used mainly for the parameter working in the storage area. 4. MODEM (IC5) Performs the modulation and the demodulation for FAX communication. 5. Read Section CIS image sensor to read transmitted documents. 6. Motor Driver (IC7) Drives the transmission motor and the reception motor. 7. Thermal Head Contains heat-emitting elements for dot matrix image printing. 8. Sensor Section Composed of a cover open and film end switch, a document set switch, a document top switch, a paper top sensor and a motor position switch. 9. Power Supply Board Switching Section Supplies +6V and +24V to the unit.
12
6.2.1.
MESSAGE
+6V
GATE ARRAY
SENSOR x2
(Doc sensor, Read position sensor)
KEY MATRIX
(Not Used)
MIC
DIGITAL BOARD
IC5
MODEM
LINERX Transformer LINETX Rx
ANALOG BOARD
+6V
REG BOA
+5V
IC4
FLASH 4Mbit PROGRAM 3.3V IC2 FLASH 4Mbit (TAM Model) 3.3V IC6
LINE
REG
Relay
13
Tx ANALOG 32.256MHz SW IC10
+3.3
ALC CPC
RESET
24MHz
+24V
OSC CPU
256kbit ROM OP-PANEL I/F
(Not Used)
EXT. L INE
FET
THON
BUFFER
PRINTER CONTROL
64Kbit SRAM
TONE
TONE1
(Not Used)
+5V
ASIC
VOL ACK_EN IC1
H/SRX H/STX_MUTE
Tr
LED ON
BELL
+5V
CLK, SIG
IMAGE PROCESSING
JAM HOOK
CIS
IC7 MOTOR DRIVER
SERIAL I/F
RTC
PAPER
RLY
To FLASH PROGRAMMER
KX-FT932BR-B
KX-FT932BR-B
6.3.
6.3.1.
Control Section
ASIC (IC1)
This custom IC is used for the general FAX operations. KB for the image processing. 1. CPU: 7. THERMAL HEAD I/F: This model uses a Z80 equivalent to the CPU operating Transmits the recorded data to the thermal head. at 12 MHz. Most of the peripheral functions are performed 8. MOTOR I/F: by custom-designed LSIs. Therefore, the CPU only works Controls the transmission motor which feeds the docufor processing the results. ment. 2. RTC: Controls the receiving motor which feeds the recording Real Time Clock paper. 3. DECODER: 9. OPERATION PANEL I/F: Decodes the address. Serial interface with Operation Panel. 4. ROM/RAM I/F: 10. I/O PORT: Controls the SELECT signal of ROM or RAM and the I/O Port Interface. bank switching. 11. ANALOGUE UNIT: 5. CIS I/F: Electronic volume for the monitor. Controls the document reading. Sends beep tones, etc. 6. IMAGE DATA RAM: This memory is programmed into the ASIC and uses 8 Note*: This memory is incorporated into the ASIC (IC1) and used for the image processing. Descriptions of Pin Distribution (IC1)
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 SIGNAL VSSA VDDA 3.3 AIN1 AIN2 AIN3 AMON VSS X32OUT X32IN VDD (3.3V / B) XBACEN XRAMCS VDD (3.3V / B) VDD (2.5V/B) FTG F1 F2/OP FR/OP CPC RVN IRDATXD/IOP IRDARXD/IOP80 TXD/IOP RXD/IOP XRTS/IOP XCTS/IOP VDD (2.5V) TONE1 TONE2 VOLUREF VOLUOUT VOLUIN XNMI FMEMDO/IOP VDD (3.3V) VSS VSS VDD (3.3V) I/O POWER SUPPLIED VOLTAGE GND 3.3V 3.3V 3.3V 3.3V 3.3V GND 3.3V/BATT 3.3V/BATT ----3.3V/BATT 3.3V/BATT --------3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V ----3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V ----GND GND ----DESCRIPTION POWER SOURCE (ANALOG GND) POWER SOURCE (ANALOG +3.3V) CIS IMAGE SIGNAL INPUT (ATN1) THERMISTOR TEMPERATURE WATCH INPUT LINE VOLTAGE DETECTION SIGNAL INPUT (DCIN) ANALOG SIGNAL MONITOR TERMINAL POWER SOURCE (GND) RTC (32.768KHz) CONNECTION RTC (32.768KHz) CONNECTION POWER SOURCE (+3.3V/LITHIUM BATTERY) BACKUP ENABLE XRAMCS POWER SOURCE(+3.3V / LITHIUM BATTERY) POWER SOURCE (+2.5V / LITHIUM BATTERY) SH SIGNAL OUTPUT FOR CIS (FTG) 01 SIGNAL OUTPUT FOR CIS (F1) OUTPUT PORT (HEADON) OUTPUT PORT (MDMRST) INPUT PORT (CPC) INPUT PORT (PAPER) INPUT PORT (JAM) OUTPUT PORT (HSTX MUTE) INPUT PORT (BELL) PORT (TELRXEN) INPUT PORT (PSHORT) PORT (MDMTXEN) POWER SOURCE (+2.5V) TONE OUTPUT TONE OUTPUT ANALOG REF VOLTAGE VOLUME OUTPUT VOLUME INPUT HIGH FIXED OUTPUT PORT (LED ON) POWER SOURCE (+3.3V) POWER SOURCE (GND) POWER SOURCE (GND) POWER SOURCE (+3.3V)
A A A A O I I O
O O O O I I I O I I/O I I/O A A A A A I O
14
KX-FT932BR-B
SIGNAL MIDAT/IOP MICLK/IOP MILAT/IOP 20KOSC/IOP XWAIT HSTRD/IOP HSTWR/IOP XOPRBE ADR15 ADR14 ADR13 VDD (2.5V) XOUT XIN VSS VDD (3.3V) XTEST TEST1 TEST2 TEST3 TEST4 XMDMINT XMDMCS XRAS/IOP XCAS1/IOP XCAS2/IOP XRESCS2 DB3 DB2 DB4 DB1 DB5 VDD (3.3V) VSS VSS VDD (3.3V) DB0 DB6 DB7 XROMCS RD WR ADR0 ADR1 ADR2 ADR3 ADR4 ADR5 VSS VDD (2.5V) ADR6 ADR7 ADR8 ADR9 ADR10 ADR11 ADR12 RBA0 RBA1 RBA2 RBA3 RBA4 RBA5 RBA6/IOP96 STB1 STB2 I/O O I/O O I I O O O O O O I
I/O
O O O O O O O O O O O O O O O O
POWER SUPPLIED VOLTAGE 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V ----3.3V 3.3V GND ----3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V ----GND GND ----3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V GND ----3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V
DESCRIPTION PORT (TONE1EN) OUTPUT PORT (TONE2EN) PORT (HSRXEN) OUTPUT PORT (PWRCNT) INPUT PORT (HOOK) INPUT PORT (TEST) OUTPUT PORT (BLEEDER_ON) OUTPUT PORT (MFCS) CPU ADDRESS BUS 15 (NOT USED) CPU ADDRESS BUS 14 (NOT USED) CPU ADDRESS BUS 13 (NOT USED) POWER SOURCE (+2.5V) SYSTEM CLOCK (24MHz) SYSTEM CLOCK (24MHz) POWER SOURCE (GND) POWER SOURCE (+3.3V) 24MHz CLOCK HIGH FIXED HIGH FIXED HIGH FIXED HIGH FIXED MODEM INTERRUPT MODEM CHIP SELECT DRAM ROW ADDRESS STROBE (RAS) DRAM COLUMN ADDRESS STROBE (CAS) PORT (SPMUTE) FLASH CHIP SELECT (XRESCS2) CPU DATA BUS 3 CPU DATA BUS 2 CPU DATA BUS 4 CPU DATA BUS 1 CPU DATA BUS 5 POWER SOURCE (+3.3V) POWER SOURCE (GND) POWER SOURCE (GND) POWER SOURCE (+3.3V) CPU DATA BUS 0 CPU DATA BUS 6 CPU DATA BUS 7 FLASH (IC2) CHIP SELECT CPU RD CPU WR CPU ADDRESS BUS 0 CPU ADDRESS BUS 1 CPU ADDRESS BUS 2 CPU ADDRESS BUS 3 CPU ADDRESS BUS 4 CPU ADDRESS BUS 5 POWER SOURCE (GND) POWER SOURCE (+2.5V) CPU ADDRESS BUS 6 CPU ADDRESS BUS 7 CPU ADDRESS BUS 8 CPU ADDRESS 9 CPU ADDRESS 10 CPU ADDRESS 11 CPU ADDRESS 12 ROM/RAM BANK ADDRESS 0 ROM/RAM BANK ADDRESS 1 ROM/RAM BANK ADDRESS 2 ROM/RAM BANK ADDRESS 3 ROM/RAM BANK ADDRESS 4 ROM/RAM BANK ADDRESS 5 OUTPUT PORT (NC) STROBE SIGNAL OUTPUT TO THERMAL HEAD STROBE SIGNAL OUTPUT TO THERMAL HEAD
15
KX-FT932BR-B
NO. 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144
SIGNAL STB3 XRESET VDD (3.3V) VSS VSS VDD (3.3V) XORESET VDD(5V) VSS XRESETI WDERR THDAT THCLK THLAT STBNP RM0/IOP RM1/IOP RM2/IOP RM3/IOP RXE/IOP TMO VDD (2.5V) VSS TM1/IOP TM2/IOP TM3/IOP TXE/IOP KSTART KLATCH KSCLK KTXD KRXD FMEMCLK/IOP FMEMDI/IOP ADSEL1 VDDA (2.5V) VREFB VCL VREFT VSSA O I
I/O
I O O O O I O O O O O O
O O O I O O O O I O O O A A A
POWER SUPPLIED VOLTAGE 3.3V 3.3V ----GND GND ----3.3V ----GND 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V ----GND 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 2.5V 3.3V 3.3V 3.3V GND
DESCRIPTION OUTPUT PORT (NC) RESET INPUT POWER SOURCE (+3.3V) POWER SOURCE (GND) POWER SOURCE (GND) POWER SOURCE (+3.3V) NOT USED POWER SOURCE (+5V) POWER SOURCE (GND) RESET INPUT WATCHED ERROR OUTPUT SIGNAL RECORDED IMAGE OUTPUT (THDAT) CLOCK OUTPUT FOR DATA TRANSFER (THCLK) PULSE OUTPUT FOR DATA LATCH (THLAT) INPUT PORT (MOT-POS) MOTOR A PHASE MOTOR B PHASE MOTOR /A PHASE MOTOR /B PHASE MOTOR ENABLE OUTPUT PORT (NC) POWER SOURCE (+2.5V) POWER SOURCE (GND) OUTPUT PORT (ACK_EN) OUTPUT PORT (CISON) OUTPUT PORT (RLY) INPUT PORT (CUT_POS) OPERATION PANEL CONTROL OPERATION PANEL CONTROL OPERATION PANEL CONTROL OPERATION PANEL CONTROL OPERATION PANEL CONTROL OUTPUT PORT (OPRESET) OUTPUT PORT (NC) CHANNEL SELECT SIGNAL FOR AIN2 POWER SOURCE (ANALOG +2.5V) A/D CONVERTER'S ZERO STANDARD VOLTAGE OUTPUT ANALOG PART STANDARD VOLTAGE SIGNAL A/D CONVERTER'S FULL SCALE VOLTAGE OUTPUT POWER SOURCE (ANALOG GND)
16
KX-FT932BR-B
6.3.2.
This 512KB ROM (FLASH MEMORY) carries a common area of 32KB and bank areas which each have 8KB (BK4~BK63). The addresses from 0000H to 7FFFH are for the common area and from 8000H to 9FFFH are for the bank areas.
6.3.3.
The DRAM serves as CPU and receives memory. The address is F200H~F3FFH (DRAM access window 1) and F600H~F7FFH (DRAM access window 2).
6.3.4.
The output signal (reset) from pin 4 of the voltage detect IC (IC3) is input to the ASIC (IC1) 114 pin.
1. During a momentary power interruption, a positive reset pulse of 50~70 msec is generated and the system is reset completely.
2. The watch dog timer, built-in the ASIC (IC1), is initialized by the CPU about every 1.5 ms. When a watch dog error occurs, pin 115 of the ASIC (IC1) becomes low level. The terminal of the 'WDERR' signal is connected to the reset line, so the 'WDERR' signal works as the reset signal.
17
KX-FT932BR-B
6.3.5.
1. Function This unit has a lithium battery (BAT1) which works for the Real Time Clock (RTC, Integrated into ASIC:IC1). The RTC continues functioning, even when the power switch is OFF, backed up by a lithium battery. 2. Circuit Operation When the power is turned ON, power is supplied to RTC (IC1). At this time, the voltage at pin 14 of RTC (IC1) is +3.3V. When the power is turned OFF, the battery supplies the power to RTC through J1, R80, D503. At that time, the voltage at pin 14 of IC1 are about +2.5V. When the power is OFF and the +5V and +3.3V voltages decrease, the LOW is input to pin 114 of IC1. Pin 111 of IC1 outputs the reset signals. Pin 11 of IC1 become low, then RTC (IC1) go into the back up mode, when the power consumption is lower.
18
KX-FT932BR-B
6.3.6.
1. Function The thermistor changes the resistor according to the temperature and uses the thermistor's characteristics. The output of pin 139 of IC1 becomes a low level. Then when it becomes a high level, it triggers point A. In point C, according to the voltage output time, the thermal head's temperature is detected. After the thermal head temperature is converted to voltage in B, it is then changed to digital data in the A/D converter inside IC1. The CPU decides the strobe width of the thermal head according to this value. Therefore, this circuit can keep the thermal head at an even temperature in order to stabilize the printing density and prevent the head from being overheated.
19
KX-FT932BR-B
6.4.
6.4.1.
Facsimile Section
Image Dara Flow During Facsimile Operation
Copy (Fine, Super-Fine, Photo) 1. Line information is read by CIS (to be used as the reference white level) via route (1), and is input to IC1. Refer to Block Diagram (P.21) 2. In IC1, the data is adjusted to a suitable level for A/D conversion in the Analog Signal Processing Section, and via route (2) it is input to A/D conversion (8 bit). After finishing A/D conversion, the data is input to the Image Processing Section via route (3). Then via route (4) and route (5), it is stored in RAM as shading data. 3. The drafts information that is read by CIS is input to IC1 via route (1). After it is adjusted to a suitable level for A/D conversion via route (2), the drafts information is converted to A/D (8 bit), and it is input to the Image Processing Section. The other side, the shading data which flows from RAM via route (6) and route (7), is input to the Image Processing Section. After finishing the drafts information image processing, white is regarded as 0 and black is regarded as 1. Then via routes (4) and (5), they are stored in RAM. 4. The white/black data stored as above via routes (6) and (8) is input to the P/S converter. The white/black data converted to serial data in the P/S converter is input to the Thermal Head via route (9) and is printed out on recording paper. Note: Fine: Reads 3.85 lines/mm Super Fine: Reads 7.7 lines/mm Photo: Reads 15.4 lines/mm Transmission 1. Same processing as Copy items 1 - 3. 2. The data stored in the RAM of IC1 is output from IC1 via routes (6) and (10), and is stored in the system bus. Via route (11), it is stored in the communication buffer inside DRAM (IC4). 3. While retrieving data stored in the communication buffer synchronous with the modem, the CPU (inside IC1) inputs the data to the modem along route (12), where it is converted to serial analogue data and forwarded over the telephone lines via the NCU Section. Reception 1. The serial analog image data is received over the telephone lines and input to the modem via the NCU section, where it is demodulated to parallel digital data. Then the CPU (IC1) stores the data in the communication buffer DRAM (IC4) along route (11). 2. The data stored in DRAM (IC4) is decoded by the CPU (IC1) via route (12), and is stored in RAM via routes (13) and (5). 3. Same processing as Copy item 4.
20
KX-FT932BR-B
6.4.2.
Block Diagram
21
KX-FT932BR-B
6.4.3.
Thermal Head
1. Function This unit utilizes state of the art thermal printer technology. The recording paper (roll paper) is chemically processed. When the thermal head contacts this paper it emits heat momentarily, and black dots (appearing like points) are printed on the paper. If this continues, letters and/or diagrams appear, and the original document is reproduced.
2. Circuit Operation There are 27 driver ICs aligned horizontally on the thermal head and each one of these ICs can drive 64 heat emitting registers. This means that one line is at a density of 6427=1728 dots=(8 dots/mm). White/Black (white=0, black=1) data in one line increments is synchronized at IC1 pin 117 (THCLK), and sent from IC1 pin 116 (THDAT) to the shift register of the ICs. The shift registers of the 27 ICs are connected in series, and upon the shift of dot increment 1728, all the shift registers become filled with data, and a latch pulse is emitted to each IC from IC1 pin 118 (THLAT).With this latch pulse, all the contents of the shift registers are latched to the latch registers. Thereafter, through the addition of strobes from the IC1 pins (103 - 104) only black dot locations (=1) among latched data activates the driver, and the current passes to heat the emitting body causing heat emission. Here, the two line strobes, STB1 and STB2, impress at intervals of 9.216 msec, as required for one-line printout. The sequence is shown on the next page. [Moreover, for the strobe width, the thermistor value inside the thermal head is detected according to IC1 pin 4. (See Block Diagram (P.21).) Depending on that value, the strobe width is recorded in FLASH (IC2). Accordingly, the strobe width is determined. When the thermal head is not used, the IC1 (17, HEADON) becomes low, Q6 turns OFF, Q7 turns OFF, and the +24 V power supply for the thermal head driver is not impressed to protect the IC.
22
KX-FT932BR-B
23
KX-FT932BR-B
6.4.4.
Scanning Block
The scanning block of this device consists of a control circuit and a contact image sensor made up of a celfoc lens array, a light source, and photoelectric conversion elements.
When an original document is inserted and the start button pressed, pin 129 of IC1 goes to a high level and the transistor Q14 turns on.This applies voltage to the light source to light it. The contact image sensor is driven by each of the FTG-F1 signals output from IC1, and the original image illuminated by the light source undergoes photoelectric conversion to output an analogue image signal (AIN). The analogue image signal is input to the system ASIC on AIN1 (pin 3 of IC1) and converted into 8-bit data by the A/D converter inside IC1. Then this signal undergoes digital processing in order to obtain a high-quality image.
24
KX-FT932BR-B
6.4.5.
1. Function One individual stepping motor is used for transmission and reception. It feeds the document or recording paper synchronized for reading or printing. 2. Circuit Operation During motor drive, ASIC IC1 pin 124 becomes a high level, and Q2 and Q1 go ON as a result. +24 V is supplied tothe motor coil. Stepping pulses are output from gate array IC1, causing driver IC7 to go ON. The motor coil is energized sequentially in 2 phase increments or 1-2 phase increments, which causes a 1-step rotation. A 1-step rotation is 0.13mm of recording paper or document paper. The timing chart is below.
Stepping Motor Phase Pattern Function Copy FAX Mode Fine/Photo Super Fine STD Fine/Photo Super Fine Paper Feed Phase Pattern 1-2 1-2 2 1-2 1-2 2 Speed 432 pps 216 pps 432 pps 432 pps 216 pps 432 pps
When the motor is OFF, gate array IC1 pin 124 becomes a low level and Q2 and Q1 also turns OFF. Instead of +24V, +5V is suplied through D501 so that the motor is held in place.
25
KX-FT932BR-B
6.5.
Operation Panel
26
KX-FT932BR-B
6.5.1.
This sensor is a detection switch for recording the position of the CAM.
Digital Board Home position Other Signal (IC1-119 Pin) Low level High level
6.5.2.
When there is no recording paper, the plate is separated from the switch lever and the switch turns off. Pin 20 of IC1 becomes a high level. When there is recording paper, the plate pushes the switch lever and the switch turns ON. Pin 20 of IC1 becomes a low level.
Analog Board Paper No paper Signal (IC1-20 Pin) Low level High level
27
KX-FT932BR-B
6.5.3.
When the handset is lifted, the switch turns ON, and the signal at pin 43 of IC1 becomes low. When the handset is returned, the switch turns OFF, and the signal at pin 43 of IC1 becomes high.
Digital Board SW ON-Hook OFF-Hook OFF ON Signal High level (IC1-43 pin) Low level
6.5.4.
The JAM sensor is a detection switch for determining whether the recording paper edge is in the correct position or not. If the recording paper cannot be detected correctly at the JAM sensor position even when recording paper is present, then JAM is displayed. If the recording paper is at the sensor position, then the switch turns on the IC1-21pin switches to a high level.
Analog Board Paper No paper Signal (IC1-21 Pin) Low level High level
28
KX-FT932BR-B
6.5.5.
When a document is brought to the read position, the SW becomes ON, and the input signal of IC1-5 pin (Operation) becomes a low level. When there is no document at the read position, the SW becomes OFF, and the input signal of IC1-5 pin (Operation) becomes a high level.
Operation Board Out of the Read Position At the Read Position Signal (IC1-5 pin) High level Low level
6.5.6.
When a document is set, the SW becomes ON, and input signal of IC1-6 pin (Operation) becomes a low level. When there is no document, the SW becomes OFF, and the input signal of IC1-6 pin (Operation) becomes a high level.
Operation Board No document Set document Signal (IC1-6 pin) High level Low level
29
KX-FT932BR-B
6.6.
6.6.1.
Modem Section
Function
The unit uses a 1 chip modem (IC5) that serves as an interface between the control section for FAX transmission and reception and the telephone line. During a transmitting operation, the digital image signals are modulated and sent to the telephone line. During a receiving operation, the analogue image signals which are received via the telephone line are demodulated and converted into digital image signals. The communication format and procedures for FAX communication are standardized by ITU-T. This 1 chip modem (IC5) has hardware which sends and detects all of the necessary signals for FAX communication (DTMF). It can be controlled by writing commands from the CPU (IC1: inside ASIC) to the register in the modem (IC5). This modem (IC5) also sends DTMF signals, generates a call tone (from the speaker), and detects a busy tone and dial tones. Overview of Facsimile Communication Procedures (ITU-T Recommendation): 1. ON CCITT (International Telegraph and Telephone Consultative Committee) The No. XIV Group of CCITT, one of the four permanent organizations of the International Telecommunications Union (ITU), investigates and make recommendations on international standards for facsimiles. 2. Definition of Each Group Group I (G1) Official A-4 size documents without using formats which reduce the band width of a signal are sent over telephone lines.Determined in 1968. Transmission for about 6 minutes at a scanning line density of 3.85 lines/mm. Group II (G2) Using reduction technology in the modulation/demodulation format, an A-4 size document is sent at an official scanning line density of 3.85 lines/mm for about 3 minutes. Methods to suppress redundancy are not used. Determined in 1976. Group III (G3) Method of suppressing redundancy in the image signal prior to modulation is used. An A-4 size document is sent within about one minute. Determined in 1980. Group IV (G4) Transmission is via the data network. A method is provided for suppressing redundancy in signals prior to transmission, and error-free reception of transmission is possible. The scope of these facsimile applications is not limited simply to transmission of written statements. Through symbiotic linkages with other communication methods, it can be expected to expand to include integrated services. 3. Facsimile Call Time Series As shown in the following diagram, the facsimile call time series is divided into five phases.
30
KX-FT932BR-B
Phase A: Call setting Call setting can be manual/automatic. Phase B: Pre-message procedure Phase B is a pre-processing procedure and sequence for confirming the status of the terminal, transmission route, etc., and for terminal control. It implements terminal preparation status, determines and displays terminal constants, confirms synchronization status, etc. and prepares for transmission of facsimile messages. Phase C: Message transmission Phase C is the procedure for the transmitting facsimile messages. Phase D: Post message procedure Phase D is the procedure for confirming that the message is completed and received. For continuous transmission, phase B or phase C is repeated for transmission. Phase E: Call retrieval Phase E is the procedure for call retrieval, that is for circuit disconnection. 4. Concerning Transmission Time Transmission Time = Control Time + Image Transmission Time + Hold Time
Transmission time consists of the following. Control time: This is time at the start of transmission when the functions at the sending and receiving sides are confirmed, the transmission mode is established, and transmission and reception are synchronized. Image transmission time: This is the time required for the transmission of document contents (image data). In general, this time is recorded in the catalog, etc. Hold time: This is the time required after the document contents have been sent to confirm that the document was actually sent, and to check for telephone reservations and/or the existence of continuous transmission. 5. Facsimile Standards
Telephone Network Facsimile G3 Machine Telephone Network Signal Mode T. 30 Binary Digital PSK (V. 27 ter) or QAM (V. 29) 300 bps (Control Signal) 2400, 4800, 7200, 9600 bps (FAX Signal) 1 dimension: MH Mode 2 dimension: MR Mode (K=2.4) Main Scan: 8 pel/mm Sub Scan: 3.85, 7.7l/mm EOL Signal Depends on the degree of data reduction. Minimum Value: 10, 20 Can be recognized in 40ms.
Item Connection Control Mode Terminal Control Mode Facsimile Signal Format Modulation Mode Transmission Speed Redundancy Compression Process (Coding Mode) Resolution Line Synchronization Signal 1 Line Transmission Time [ms/line]
31
KX-FT932BR-B
6. Explanation of Communication and Compression Technology a. G3 Communication Signals (T. 30 Binary Process) For G3 Facsimile communication, this is the procedure for exchanging control signals between the sending and receiving machines both before and after transmission of image signals. Control signals at 300 bps FSK are: 1850 Hz...0, 1650Hz...1. An example of a binary process in G3 communication is shown below.
Explanation of Signals Control signals are comprised mainly of 8-bit identification signals and the data signals added to them. Data signals are added to DIS and DCS signals. Signal.....DIS (Digital Identification Signal) Identification Signal Format.....00000001 Function: Notifies the capacity of the receiving unit. The added data signals are as follows. Signal.....DCS (Digital Command Signal) Identification Signal Format.....X1000001 Example (Some models do not support the following items.):
Bit No. 1 2 3 4 5 6 7 8 9 DIS/DTC Transmitter --- T.2 operation Receiver --- T.2 operation T.2 IOC = 176 Transmitter --- T.3 operation Receiver --- T.3 operation Reserved for future T.3 operation features Reserved for future T.3 operation features. Reserved for future T.3 operation features. Transmitter --- T.4 operation DCS Receiver --- T.2 operation T.2 IOC = 176 Receiver --- T.3 operation
32
KX-FT932BR-B
Bit No. 10 11,12,13,14 0,0,0,0 0,1,0,0 1,0,0,0 1,1,0,0 0,0,1,0 0,1,1,0 1,0,1,0 1,1,1,0 0,0,0,1 0,1,0,1 1,0,0,1 1,1,0,1 0,0,1,1 0,1,1,1 1,0,1,1 1,1,1,1 15 16 17, 18 (0, 0) (0, 1)
(1, 0)
(1, 1) 19, 20 (0, 0) (0, 1) (1, 0) (1, 1) 21, 22, 23 (0, 0, 0) (0, 0, 1) (0, 1, 0) (1, 0, 0) (0, 1, 1) (1, 1, 0) (1, 0, 1) (1, 1, 1) 24 25 26 27 28 29 30 31 32 33 (0) (1) 34 35 36 37 38
DIS/DTC Receiver --- T.4 operation Data signaling rate V.27 ter fall back mode V.27 ter V.29 V.27 ter and V.29 Not used Reserved Not used V.27 ter and V.29 and V.33 Not used Reserved Not used V.27 ter and V.29 and V.33 and V.17 Not used Reserved Not used Reserved R87.7 lines/mm and/or 200200 pels/25.4mm Two-dimensional coding capability Recording width capabilities 1728 picture elements along scan line length of 215 mm 1% 1728 picture elements along scan line length of 215 mm 1% 2048 picture elements along scan line length of 255 mm 1% 2432 picture elements along scan line length of 303 mm 1% 1728 picture elements along scan line length of 215 mm 1% 2048 picture elements along scan line length of 255 mm 1% Invalid Maximum recording length capability A4 (297 mm) Unlimited A4 (297 mm) and B4 (364 mm) Invalid Minimum scan line time capability of the receiver 20 ms at 3.85 l/mm: T7.7 = T3.85 40 ms at 3.85 l/mm: T7.7 = T3.85 10 ms at 3.85 l/mm: T7.7 = T3.85 5 ms at 3.85 l/mm: T7.7 = T3.85 10 ms at 3.85 l/mm: T7.7 = 1/2 T3.85 20 ms at 3.85 l/mm: T7.7 = 1/2 T3.85 40 ms at 3.85 l/mm: T7.7 = 1/2 T3.85 0 ms at 3.85 l/mm: T7.7 = T3.85 Extend field 2400 bit/s handshaking Uncompressed mode Error correction mode Set to 0. Error limiting mode Reserved for G4 capability on PSTN T.6 coding capability Extend field Validity of bits 17, 18 Bits 17, 18 are valid Bits 17, 18 are invalid Recording width capability 1216 picture elements along scan line length of 151 mm 1% Recording width capability 864 picture elements along scan line length of 107 mm 1% Recording width capability 1728 picture elements along scan line length of 151 mm 1% Recording width capability 1728 picture elements along scan line length of 107 mm 1% Reserved for future recording width capability.
DCS Receiver --- T.4 operation Data signaling rate 2400 bit/s, V.27 ter 4800 bit/s, V.27 ter 9600 bit/s, V.29 7200 bit/s, V.29 14400 bit/s, V.33 12000 bit/s, V.33 Reserved Reserved 14400 bit/s, V.17 12000 bit/s, V.17 9600 bit/s, V.17 7200 bit/s, V.17 Reserved Reserved Reserved Reserved R87.7 lines/mm and/or 200200 pels/25.4mm Two-dimensional coding capability Recording width 1728 picture elements along scan line length of 215 mm 1% 2432 picture elements along scan line length of 303 mm 1%
Invalid Maximum recording length A4 (297 mm) Unlimited B4 (364 mm) Invalid Minimum scan line time 20 ms 40 ms 10 ms 5 ms
0 ms Extend field 2400 bit/s handshaking Uncompressed mode Error correction mode Frame size 0 = 256 octets 1 = 64 octets Error limiting mode Reserved for G4 capability on PSTN T.6 coding enabled Extend field Recording width Recording width indicated by bits 17, 18 Recording width indicated by this field bit information Middle 1216 elements of 1728 picture elements Middle 864 elements of 1728 picture elements Invalid Invalid
33
KX-FT932BR-B
Bit No. 39 40 41 42 43 44
DIS/DTC Reserved for future recording width capability. Extend field R815.4 lines/mm 300300 pels/25.4 mm R1615.4 lines/mm and/or 400400 pels/25.4 mm Inch based resolution preferred
DCS Extend field R815.4 lines/mm 300300 pels/25.4 mm R1615.4 lines/mm and/or 400400 pels/25.4 mm Resolution type selection 0: neritic based resolution 1: inch based resolution Dont care Dont care Set to 0. Extend field
45 46 47 48
Metric based resolution preferred Minimum scan line time capability for higher resolutions 1: T15.4 = 1/2T7.7 0: T15.4 = T7.7 Selective Polling capability Extend field
Note 1 - Standard facsimile units conforming to T.2 must have the following capability: Index of cooperation (IOC)=264. Note 2 - Standard facsimile units conforming to T.3 must have the following capability: Index of cooperation (IOC)=264. Note 3 - Standard facsimile units conforming to T.4 must have the following capability: Paper length=297 mm.
Signal Training 1 Identification Signal Format Function A fixed pattern is transmitted to the receiving side at a speed (2400 bps to 9600 bps) designated by DCS, and the receiving side optimizes the automatic equalizer, etc., according to this signal. Sends 0 continuously for 1.5 seconds at the same speed as the training signal. Notifies the sending side that TCF has been properly received. If TCF is not properly received, FTT (Failure To Train) X0100010 is relayed to the sender. The sender then reduces the transmission speed by one stage and initiates training once again. Used for reconfirming the receiving side like training 1. Sends 12 bits (0...01 6 times) to the receiver at the same speed as the image signal and notifies completion of transmission of the first sheet. End of one communication End of 1 page reception Phase E starts. Completion of transmission of 1 page. If there are still more documents to be sent, they are output instead of EOP. After MCF reception, the sender transmits an image signal of the second sheet. If there is an operator call from the sender, it is output after RTC. This is output when an operator call is received.
X0100001
Training 2 Image Signal RTC (Return to Control) EOP (End of Procedure) MCF (Message Confirmation) DCN (Disconnect) MPS (Multi-Page Signal)
34
KX-FT932BR-B
b. Redundancy Compression Process Coding Mode This unit uses one-dimensional MH format.
35
KX-FT932BR-B
6.6.2.
The modem (IC5) has all the hardware satisfying the CCITT standards mentioned previously. When the ASIC IC1 (61) is brought to a low level, the modem (IC5) is chip-selected and the resistors inside IC are selected by the select signals from ASIC (IC1) ADR0-ADR4. The commands are written through the data bus, and all the processing is controlled by the ASIC (IC1) according to CCITT procedures. The INT signal dispatched from IRQ (pins 100 of IC5) to ASIC (IC1) when the transmission data is accepted and the received data is demodulated, the ASIC (IC1) implements post processing. This modem (IC5) has an automatic application equalizer. With training signal 1 or 2 during G3 reception, it can automatically establish the optimum equalizer. The modem (IC5) operates using the 32.256 MHz clock (X3). 1. Facsimile Transmission The digital image data on the data bus is modulated in the modem (IC5), and sent from pin 69 via Analog SW IC10, amplifier IC9 and the NCU section to the telephone line. Refer to Sgnal Route(P.108). 2. Facsimile Reception The analog image data which is received from the telephone line passes through the NCU section and enters pin 47 of the modem (IC5). The signals that enter pin 47 of the modem (IC5) are demodulated in the board to digital image signals, then placed on the data bus. In this case, the image signals from the telephone line are transmitted serially. Hence, they are placed on the bus in 8 bit units. Here, the internal equalizer circuit reduces the image signals to a long-distance receiving level. This is designed to correct the characteristics of the frequency band centered about 3 kHz and maintain a constant receiving sensitivity. It can be set in the service mode. Refer to Sgnal Route(P.108). 3. DTMF Transmission (Monitor tone) The DTMF signal generated in the modem (IC5) is output from pin 56, and is then sent to the circuit on the same route as used for facsimile transmission. Refer to Sgnal Route(P.108). (DTMF Monitor Tone) Refer to Sgnal Route(P.108). 4. Call Tone Transmission This is the call signal which is generated in the ASIC (IC1) and sent to the speaker. Refer to Sgnal Route(P.108). 5. Busy/Dial Tone Detection The path is the same as FAX receiving. When it is detected, the carrier detect bit of the resistor in the modem (IC5) becomes 1, and this status is monitored by the ASIC (IC1). 6. Caller ID Detection The caller ID signal which is received from the telephone line/passes through IC1 pin (2-1). And it enters pin 50 of the modem (IC5).
36
KX-FT932BR-B
6.7.
6.7.1.
NCU Section
General
It is composed of bell detection circuit, pulse dial circuit, line amplifier, sidetone circuits.
6.7.2.
1. Circuit Operation The signal waveform for each point is indicated below. The signal (low level section) input to pin 23 of ASIC IC1 on the digital board. TEL LINE PC1 (1, 2 4) CN1 (11) {CN2 (11) IC1 (23)} Note:{ } : inside the digital board
6.7.3.
Normally (ON-HOOK condition), LINE RELAY (RLY1) is OFF. While OFF-HOOK, RLY1 turns ON. This LINE RELAY is controlled by pin 130 of IC1 through the Q7. ON-HOOK: IC1 (130) Low Level Q7 OFF RLY1 OFF OFF-HOOK: IC1 (130) High Level Q7 ON RLY1 ON
6.7.4.
Make state: IC1 (130) High Level Q7 ON RLY1 ON Break state: IC1 (130) Low Level Q7 OFF RLY1 OFF
37
KX-FT932BR-B
6.7.5.
1. Circuit Operation The reception signal received as output from line transformer T1 is given as input to C17, R13 and IC2(2). Then it is input to the reception system at an amplifier gain of 2.5 dB from pin (2). The transmission signal is input from CN1 pin (5), and output to the TEL line through C11, R16, IC2(6,7) and T1. Without a side tone circuit, the transmission signal would return to the reception amplifier via C28, R27 and R26. Here, the signal output from CN1 pin (5) passes through C28, R23, R22, C21 and R18, and enters the amplifier IC2 pin (3). This is used to cancel the return portion of the transmission signal. This is the side tone circuit.
38
KX-FT932BR-B
6.7.6.
1. Function This unit is compatible with the Caller ID service offered by your local telephone company. To use this feature, you must subscribe to a Caller ID service. The data for the caller ID from the telephone exchange is sent during the interval between the first and second rings of the bell signal. The data from the telephone exchange is a modem signal which is modulated in an FSK (Frequency Shift Keying) format. Data 0 is a 1200 Hz sine wave, and data 1 a 2200 Hz sine wave. There are two type of the message format which can be received:i.e.the single data message format and multiple data message format. The multiple data format allows to transmit the name and data code information in addition to the time and telephone number data. When there is multiple data in the unit, the name or telephone number are displayed. 2. Circuit Operation: The caller ID signal input from TEL LINE is processed with IC5. Refer to Sgnal Route (P.108) for the route of caller ID signal.
39
KX-FT932BR-B
6.7.7.
1. Function This unit is compatible with the Caller ID service offered by your local telephone company. To use this feature, you must subscribe to a Caller ID service. The data for the Caller ID from the telephone exchange is sent before the first ring signal. The data from the telephone exchange is sent by DTMF signal. 2. Circuit Operation: The Caller ID signal from TEL LINE is processed with MODEM (IC5). Refer to Sgnal Route (P.108) for the route of Caller ID (DTMF) signal.
40
KX-FT932BR-B
6.8.
6.8.1.
The general ITS operation is performed by the modem IC5. The alarm tone, the key tone, the calling tone and the beep are output from the ASIC IC1 (digital board).
6.8.2.
Handset Circuit
1. Function This circuit controls the conversation over the handset, i.e. the transmitted and received voices to and from the handset. 2. Signal path Refer to Sgnal Route (P.108)
6.8.3.
1. Function This circuit monitors various tones, such as 1 DTMF tone, 2 Alarm/Beep/Key tone/Bell 3 Dummy ring back tone. 2. Signal path Refer to Sgnal Route (P.108)
6.9.
6.9.1.
1. Function This is the parallel connection DTMF signal for the TEL mode between a and b. When the other party is a FAX, the unit changes to FAX receiving. 2. Signal Path Refer to Sgnal Route (P.108)
41
6.9.2.
KX-FT932BR-B
R10
C8
+24VA
IC2
R2
R13
Circuit Diagram
8 2 3 C7 4
Ref
R18
D1
R11
POS1
CN3 1a 2 b
R1 4 R15
R2 2 R23
R2 6 R27
C14
C28
42
Analog Board
13
13
C216
R221 C217
R220
L1
CN1
CN2
KX-FT932BR-B
ASIC
CN2
CN206 IC1
CN1
DIGITAL BOARD
43
KX-FT932BR-B
Density LED1 (IC1-22pin) LED15 (IC1-21pin) LED14 (IC1-20pin) LED1 LED15 LED14
Dark
44
KX-FT932BR-B
Block Diagram
AC Input G
+ -
Input Circuit
Rectifier Circuit C5
R2 R3 R4
Converter Circuit C
Q1
24V
D
0 C-D Voltage Wave Form
6V Output Circuit
GND 9~6V
Control Circuit
0 E-F G-H Voltage Wave Form 0
O.C.L
E H
[Input Circuit] The input current goes into the input rectifier circuit through the filter circuit. The filter circuit decreases the noise voltage and the noise electric field strength. [Rectifier Circuit] The input current is rectified by D10, D11, D12 and D13 and charges C5 to make DC voltage. Then it supplies power to the converter circuit. [Kick-on voltage circuit] Bias is applied to the Q1 gate via this circuit when the AC power is turned on and Q1 begins operating.
45
KX-FT932BR-B
The following is an overview of how the power supply unit is controlled. The control method of this power supply unit is pulse width modulation. When Q1 is ON, the energy is charged in the transfer primary coil according to E1. When Q1 is OFF, the energy is output from the secondary transfer as follows. L D1 Load L Then the power is supplied to the Load. When Q1 is ON, power is not output from the secondary side. The output voltage is fed back in the control circuit according to the error amp rectifier. Then depending on how f is controlled, stabilization occurs. Also, when the current load becomes too large, in order to decrease the voltage output, the increase in f is controlled and the output voltage is stabilized. Therefore, basically the timing: f of Q1 controls the output voltage.
46
KX-FT932BR-B
[Surge Absorber Circuit] This circuit is for absorbing surge voltage generated by the Q1. [Control Circuit and Detecting Circuit] The control circuit amplifies the output with increased voltage detected in the error detecting circuit. Then it drives the main transistor. In this power supply, the oscillation frequency(f) of the main transistor is defined by changing the output load. This is shown as follows. When the output voltage of the 24V circuit increases, the current of the photo coupler PC101 increases, the pulse width of the output control circuit becomes higher and the ON period of Q101 becomes shorter. [Over Current Limiter (O.C.L)] The highest drain current (Q1) is limited by controlling f of Q1 of 24V. The 24V output is limited by this circuit. [Over Voltage Circuit] If the 24V output increases because the error detecting circuit or control circuit is broken, output becomes 0V by turning on the zener diode D105.
Dummy load method (to quickly check the power supply output) Refer to Power Supply Board Section (P.110).
47
KX-FT932BR-B
48
KX-FT932BR-B
7.2.
Control Panel
Buttons (1) [CALLER ID] To use Caller ID features. (2) [STOP] To stop an operation or programming session. To erase a character/number. Press and hold to erase all characters/numbers. (3) [FLASH] To access special telephone services or for transferring extension calls. (4) [REDIAL] To redial the last number dialled. If the line is busy when you make a phone call using the [MONITOR] button, the unit will automatically redial the number up to 5 times. (5) [AUTO ANSWER] To turn the auto answer setting ON/OFF. (6) Station keys To use one-touch dial feature. (7) [FAX/START] To start sending or receiving a fax. (8) [COPY] To copy a document. (9) [TONE] To change from pulse to tone temporarily during dialling when your line has rotary pulse services. (10) [PAUSE] To insert a pause during dialing. (11) [MONITOR] To initiate dialing without lifting the handset. (12) [BROADCAST] To transmit a document to multiple parties. (13) Navigator/ [VOLUME] [PHONEBOOK] To search for a stored item. To select features or feature settings during programming. To adjust volume. To access the phonebook. (14) [SET] To store a setting during programming. (15) [MENU] To initiate or exit programming. (16) [LOWER] To select stations 6-10 for the one-touch dial feature.
49
KX-FT932BR-B
8 Installation Instructions
8.1. Installation Space
The space required to install the unit is shown below. The dimensions given are necessary for the unit to operate efficiently.
8.2.
Connections
Important: The unit will not function when there is a power failure. To make calls in emergency situations, you should connect a telephone that can function during a power failure to the telephone line. (1) Power cord Connect to the power outlet (127V, 60 Hz). (2) Telephone line cord Connect to [LINE] jack and single telephone line jack. (3) [EXT] jack Remove the stopper if attached. (4) Handset cord (5) Extension telephone (not included)
Note: Avoid excessive heat or humidity. Use the unit within the following ranges of temperature and humidity. Ambient temperature: 5C to 35C Relative humidity: 20% to 80% (without condensation) Power cord length should be less than 5 meters. Using a longer cord may reduce the voltage or cause malfunctions. Avoid direct sunlight. Do not install near devices which contain magnets or generate magnetic fields. Do not subject the unit to strong physical shock or vibration. Keep the unit clean. Dust accumulation can prevent the unit from functioning properly. To protect the unit from damage, hold both sides when you move it.
Caution: When you operate this product, the power outlet should be near the product and easily accessible. Be sure to use the telephone line cord included in this unit. Do not extend the telephone line cord. Keep the unit away from walls as far as possible to prevent a recording paper jam. Note: Before you can make calls, the dialling mode setting may need to be changed.
50
KX-FT932BR-B
8.3.
ton (
1. Open the top cover by pressing the top cover release but-
6. Press [FAX/START], then tear off the excess paper by pulling it towards you.
3. Insert the leading edge of the paper into the opening above the thermal head ( ).
Note: If the paper is secured with glue or tape, cut approximately 15 cm from the beginning of the roll before installing it. When the power cord is connected, a message is printed each time the top cover is opened then closed. If the recording paper is installed upside down, the message will not be printed. Install the paper correctly. For accessory information, see Optional Accessories (P.9).
51
KX-FT932BR-B
9 Operating Instructions
9.1. Setting Your Logo
Your logo will be printed on the top of each page sent from your unit. The logo can be your name or the name of your company. Note: Refer to Other (P.9) for display message.
1. Press [MENU].
2. Press [
] or [
3. Press [SET]. The cursor ( ) will appear on the display. Document weight Single sheet: 45 g/m2 to 90 g/m2 Multiple sheest: 60 g/m2 to 80 g/m2 Note: Remove clips, staples or other fasteners. Do not send or copy documents that are on the following types of paper: (Make a copy of the document using another copier and send the copy.) Chemically treated paper such as carbon or carbonless duplicating paper Electrostatically charged paper Badly curled, creased or torn paper Paper with a coated surface Paper with a faint image Paper with printing on the opposite side that can be seen through the other side, such as newsprint. Check that ink, paste or correction fluid has dried completely. To send a document with a width of less than 210 mm, we recommend using a copy machine to copy the original document onto A4 or letter-sized paper, then sending the copied document. 4. Enter your logo, up to 30 characters. See the following character table below for details. 5. Press [SET]. The next feature will be displayed. 6. Press [MENU].
52
KX-FT932BR-B
To select characters with dial keypad To change uppercase or lowercase letters Pressing the [ ] button will change to uppercase or lowercase letters alternately. 1. Press [2] 2 times.
3. Press [
].
To correct a mistake 1. Press [ ] or [ ] to move the cursor to the incorrect character. 2. Press [STOP]. To erase all characters, press and hold [STOP]. 3. Enter the correct character.
Note: To enter another character that is located on the same dial key, press [ ] to move the cursor to the next space.
To select characters using [ + ] or [] Instead of pressing the dial keys, you can select characters using [ + ] or []. 1. Press [] repeatedly to display the desired character. Characters will be displayed in the following order: (1) Uppercase letters (2) Number (3) Symbol (4) Lowercase letters If you press [ + ], the order will be reversed. 2. Press [ ] to insert the character. 3. Return to step 1 to enter the next character.
4. Press [ ] to move the cursor to the next space and press [5] 3 times.
53
KX-FT932BR-B
10 Test Mode
The codes listed below can be used to perform simple checks for some of the units functions. When complaints are received from customers, they provide an effective tool for identifying the locations and causes of malfunctions. To do this, you set the Service mode (Refer to Operation Flow (P.56).) first, then operate the below test items.
Test Mode Type of Mode Code Operation after code input 5 5 0 SET 5 5 1 SET 5 5 4 SET Function
FACTORY SET
Service Mode
Refer to Memory Clear Specification (P.59). Indicates the version and checks the sum of the FLASH MEMORY. Telephone line circuit is connected automatically, output the following signals on the circuit line. 1) OFF 2) 9600bps 3) 7200bps 4) 4800bps 5) 2400bps 6) 300bps 7) 2100Hz 8) 1100Hz Turns on the LEDs of the CIS and operates the read systems. Refer to CIS (Contact Image Sensor) Section (P.115). Rotates the transmission and reception motor to check the operation of the motor. 12: FAX TX / Reading memory 52: Recording paper is fed 22: Copy 44: Recording Paper reverse Press [STOP] button to quit. All LEDs above the operation panel board flash on and off, or are illuminated. Checks the LCD indication. Illuminates all the dots to check if they are normal. Refer to Operation Panel Section (P.113). Checks the button operation. Indicates the button code on the LCD while the button is pressed. Refer to Button Code Table (P.55). Refer to Operation Panel Section (P.113). Refer to Memory Clear Specification (P.59). If you enter this mode and operate sensor levers with your hands, the LCD display of the related sensor (or switch) turns ON / OFF. Also, when copying a document, the related sensor will turn ON / OFF. For each sensors operation, refer to Sensors and Switches (P.26). Do Sn Co Jm : LCD DISPLAY
5 5 5 SET 5 5 6 SET
KEY CHECK
Service Mode
MEMORY CLEAR Service Mode (except History data) SENSOR CHECK Service Mode
7 1 0 SET 8 1 5 SET
Note: The numbers in the boxes (XXX) indicate the keys to be input for the various test modes.
54
KX-FT932BR-B
When set to OFF (=2), the 12 keys and transmission frequencies are as shown. Note: After performing this check, do not forget to turn the setting off. Otherwise, dialing in DTMF signal will not work.
55
KX-FT932BR-B
11 Service Mode
The programming functions are used to program the various features and functions of the machine, and to test the machine. This facilitates communication between the user and the service man while programming the unit.
11.1.2.
Operation Flow
56
KX-FT932BR-B
11.1.3.
Code 501 502 503 514 520
521
1, 2
522 523
1:ON 2:OFF
1, 2 1~4
1 1
524
544
554 555 556 557 558 559 561 570 571 572 573 590 591 592
1: 0 km 2: 1.8 km 3: 3.6 km 4: 7.2 km Transmission equalizer select 1: 0 km 2: 1.8 km 3: 3.6 km 4: 7.2 km Document feed position adjustment 1: 3 mm value set 2: 4 mm 3: 5 mm 4: 6 mm 5: 7 mm Memory Clear ROM check DTMF single tone test 1:ON 2:OFF Monitor on FAX communication select 1:OFF 2:PHASE B 3:ALL Modem test Scan check Motor test LED test LCD test Document jam detection select 1:ON 2:OFF KEY test BREAK % select 1:61% 2:67% ITS auto redial time set X number of times ITS auto redial line disconnection time X second set Remote turn-on ring number set X number of rings FAX auto redial time set X number of times FAX auto redial time disconnection time X second set CNG transmit select 1:OFF 2:ALL 3:AUTO
1~4
When the telephone station is far from the unit or transmission cannot be performed correctly, adjust accordingly. If it is difficult to feed documents, raise the set value. If multi documents feed occurs, lower the set value.
1~5
1, 2 1~3
2 1
See Memory Clear Specification (P.59). See Test Mode(P.54). See Test Mode(P.54). Sets whether to monitor the line signal with the unit's speaker during FAX communication or not. See Test Mode(P.54). See Test Mode(P.54). See Test Mode(P.54). See Test Mode(P.54). See Test Mode(P.54). See Test Mode(P.54). See Test Mode(P.54). Sets the % break of pulse dialing according PBX. Selects the number of times that ITS is redialed (not including the first dial). Sets the interval of ITS redialing. Sets the number of rings before the unit starts to receive a document in the TEL mode. Selects the number of redial times during FAX communication (not including the first dial). Sets the FAX redial interval during FAX communication. Lets you select the CNG output during FAX transmission. ALL: CNG is output at phase A. AUTO: CNG id output only when automatic dialing is performed. OFF: CNG id not output at phase A. Refer to Sometime there is a transmit problem (P.81). See Symptom/Countermeasure Table for long distance and international calls in The unit can copy, but cannot transmit/receive (P.83). Refer to Receive Problem(P.82) and The unit can copy, but cannot transmit/receive (P.83). See Symptom/Countermeasure Table for long distance and international calls in The unit can copy, but cannot transmit/receive (P.83). Refer to Sometime there is a transmit problem(P.81) and The unit can copy, but cannot transmit/receive (P.83).
00
1 2 05 065 10 05 065 2
593
1~3
594
1, 2
57
KX-FT932BR-B
Code 595
Remarks Sets the number of acceptable error lines when the FAX reconstructs the received data. Refer to Receive Problem (P.82). Selects the FAX transmission level. Refer to Sometime there is a transmit problem (P.81) and Receive Problem (P.82). Used when there is an error problem. Refer to The unit can copy, but cannot either transmit/receive long distance or international communications (P.84). Refer to Memory Clear Specification (P.59). Adjusts the speed to start training during FAX transmission. Refer to Sometime there is a transmit problem (P.81)and The unit can copy, but the transmission and reception image are incorrect (P.86). Adjusts the speed to start training during FAX reception. Refer to Receive Problem (P.82) and The unit can copy, but the transmission and reception image are incorrect (P.86). Sets the tone detection mode after redialing. Set the CPC signal detection mode from the converter. Invalid function for thermal model. Selects the CNG detection tone of friendly reception.
596
00~15
10
598
Receiving sensitivity
43 = -43 dBm
20~48
42
710 717
718
Redial tone detect CPC mode Power ON film feed CNG detect time for friendly reception
774 815 852 853 874 875 880 881 882 961 962
T4 timer Sensor check Print test pattern Top margin DTMF ON time DTMF OFF time History list Journal 2 list Journal 3 list The time transmitting the false ring back tone The operator calling time
1:9600BPS 2:7200BPS 3:4800BPS 4:2400BPS 1:9600BPS 2:7200BPS 3:4800BPS 4:2400BPS 1:ON 2:OFF 1:A 2:B 3:OFF 1:ON 2:OFF 1:10 sec 2:20 sec 3:30 sec X 100 msec
1~4
1~4
1, 2 1, 2, 3 1, 2 1~3
1 3 1 3
00~99
00
X msec X msec
3 10 10
X sec X sec
01~10 05~30
05 13
Use this function when delay occurs in the line and communication (ex. Mobile comm) does not work well. See Test Mode(P.54). See Test Mode(P.54). ------------------------------------See Special service journal reports (P.76). See Special service journal reports (P.76). Set the time transmitting the false ring back tone to the line in TEL/FAX mode. Set the operator calling time through the speaker in TEL/FAX mode.
58
KX-FT932BR-B
11.1.4.
*1 Execute Service Mode #550 when you want to reset the all setting data keeping the user information. *2 Execute Service Mode #710 to clear the user information in case that Main Unit is recycled. Note: Please restart a power supply after clearing a memory.
59
KX-FT932BR-B
60
KX-FT932BR-B
11.2.2.
61
KX-FT932BR-B
11.2.3.
Note: See the following descriptions of this report. Item No. (1) ~ (44) are corresponding to the listed items in Descriptions of the History Report (P.63).
62
KX-FT932BR-B
63
KX-FT932BR-B
12 Troubleshooting Guide
12.1. Troubleshooting summary
12.1.1. Troubleshooting
After confirming the problem by asking the user, troubleshoot according to the instructions and observe the following precautions.
12.1.2. Precautions
1. If there is a problem with the print quality or the paper feed, first check if the installation space and the print paper meets the specifications, the paper selection lever/paper thickness lever is set correctly, and the paper is set correctly without any slack. 2. Before troubleshooting, first check that the connectors and cables are connected correctly (not loose). If the problem occurs randomly, check it very carefully. 3. When connecting the AC power cord with the unit and checking the operation, exercise utmost care when handling electric parts in order to avoid electric shocks and short-circuits. 4. After troubleshooting, double check that you have not forgotten any connectors, left any loose screws, etc. 5. Always test to verify that the unit is working normally.
64
KX-FT932BR-B
There is something wrong with the unit. [This error is displayed when the thermal head does not warm up. Check the thermistor on the thermal head and connector lead.]
The other partys fax machine is busy or has run out of recording paper. Try again.
A recording paper jam occurred. Clear the jammed paper. (Refer to Jams (P.137 ).) The document was not fed into the unit properly. Re-insert the document. If misfeeding occurs frequently, clean the document feeder rollers and try again. (Refer to Document Jams - Sending (P.137).) Attempted to send a document longer than 600 mm. Press [STOP] to remove the document. Divide the document into two or more sheets and try again. [Alternately, turn off service code #559 to enable sending of documents longer than 600 mm] (Refer to Service Function Table (P.57).)
The unit is checking and initializing the paper cutter. Wait for a moment while the check is completed.
The other partys fax machine does not support polling. Check with the other party.
The cover is open. Close it and press [FAX/START] to clear the message. The unit has run out of recording paper. Install recording paper and press [FAX/START] to clear the message.
The other partys fax machine is busy or has run out of recording paper. Try again.
The document is jammed. Remove the jammed document. (Refer to Document Jams - Sending (P.137).) Press [STOP] to eject the jammed document. The unit has a document in memory. See the other displayed message instructions to print out the document. For fax memory capacity, (Refer to Specifications (P.8)). The system is busy. Replace the handset or stop using monitor, then try again. The memory is full of received documents due to lack of recording paper or a recording paper jam. Install paper or clear the jammed paper. (Refer to Jams (P.137.) When performing broadcast transmission, the document being stored exceeded the memory capacity of the unit. Send the entire document manually.
The unit is too hot. Stop using the unit for a while and let the unit cool down. There is no space to store new items in the phonebook. Erase unnecessary items. There is no memory available to record voice messages. Erase unnecessary messages.
65
KX-FT932BR-B
1 2 3 4 5 6 7 8 8 8 9 11 13 14 15 2 2 13 13 16
28 41 42 43 44 46 48 49 50 51 54 58 59 64 65 65 68 70 72
FF
SND & RCV Modem error. For the DCN, DCN, etc. abbreviations, refer to Modem 12 Section (P.30).
SND=TRANSMISSION RCV=RECEPTION Most fax communication problems can be resolved by the following steps. 1. Change the transmit level. (Service code: 596, refer to Service Function Table(P.57).) 2. Change the TX speed/RX speed. (Service code: 717/718, refer to Service Function Table (P.57).) Note*: If the problem remains, see the following Countermeasure flow chart.
66
KX-FT932BR-B
67
KX-FT932BR-B
68
KX-FT932BR-B
69
KX-FT932BR-B
70
KX-FT932BR-B
71
KX-FT932BR-B
CROSS REFERENCE: Maintenance(P.129) ADF (Auto Document Feed) Section(P.93) Operation Panel Section(P.168) CROSS REFERENCE: Test Mode(P.54)
72
KX-FT932BR-B
73
KX-FT932BR-B
74
KX-FT932BR-B
75
KX-FT932BR-B
HOW TO READ JOURNAL REPORTS: Example: 1. Look at NO. 01 in the JOURNAL. If you want to know about the details about that item, see NO. 01 in the JOURNAL 2 and the JOURNAL 3. You can get the following information. * MODE: Fax transmission * RCV. MODE: TEL * TX SPEED: 9.6 kbps * RESOLUTION: standard * ENCODE: MH * MAKER CODE: 79 2. Look at NO. 04 in the JOURNAL 2. CNG (0003) indicates that the CNG signal has been received three times since the purchase date. For further details, see Journal 2(P.77) and Journal 3(P.78). 76
KX-FT932BR-B
12.3.2.1. Journal 2
Refer to JOURNAL 2 in Printout Example(P.78). Journal 2 displays the additional detailed information about the last 30 communications. Descriptions: (1) RCV. MODE Indicates which receive mode the unit was in when the unit received a fax message. This information is also displayed when the unit transmitted a fax message. (2) SPEED Indicates the speed of the communication. If multiple pages are transmitted or received, it indicates the last pages communication speed. If there is a communication error, ? is displayed. (3) RESOLUTION Indicates the resolution of the communication. If multiple pages are transmitted or received, it indicates the last pages resolution. If there is a communication error, ? is displayed. (4) RCV-TRIG. (CNT.) Indicates the trigger that causes the unit to switch to the fax receive mode. The available options are listed in JOURNAL 2 in Printout Example(P.78). The values in parentheses indicate how many times the trigger has been used. (For example, 0003 means three times.)
No. 1 2 3 4 5 6 7 8 9 10 Display FAX MODE MAN RCV FRN RCV VOX RMT DTMF PAL DTMF TURN-ON TIME OUT IDENT CNG OGM Function Means the unit received a fax message in the FAX mode. Means the unit received a fax message by manual operation. Means the unit received a fax message by friendly signal detection. Means the unit detected silence or no voice. Means the unit detected DTMF (Remote Fax activation code) entered remotely. Means the unit detected DTMF (Remote Fax activation code) entered by a parallel connected telephone. Means the unit started to receive after 10 rings. (Remote Turn On: Service Code #573) Means the unit started to receive after Ring Time Out in the EXT-TAM or TEL/FAX mode. Means the unit detected Ring Detection. Means the unit detected the CNG while it was sending the Dummy Ring Back Tone in the TEL/FAX mode. OR Means the unit detected the CNG while it was sending the OGM in the ANS/FAX mode. Means the unit detected the CNG while it was recording the ICM in the ANS/FAX mode.
11
CNG ICM
(5) ERRORMEMORY Indicates the reason why the unit received a fax message in memory. If you look at No.11 in the JOURNAL 2 in Printout Example(P.78), it shows the fax message was received in memory due to PAPER OUT error. NO RESPONSE DISAPPEARED ON JOURNAL The NO RESPONSE DISAPPEARED ON JOURNAL displays the information about the last 10 communications terminated by No Response. (Some of the communications terminated by No Response were not displayed in the JOURNAL.) When a fax transmission cannot be performed because the other partys unit is set to the TEL mode, No response will be printed.
77
KX-FT932BR-B
12.3.2.2. Journal 3
Refer to JOURNAL 3 in Printout Example (P.78). Descriptions: (6) ENCODE Compression Code: MH/MR (7) MSLT MSLT means Minimum Scan Line Time. Used only at the factory. (8) EQM EQM means Eye Quality Monitor. Used only at the factory. (9) ERROR LINE(RX) When an error occurs while receiving a fax, this shows the number of error lines. (10) MAKER CODE This shows a 2 digit code of the other party's fax machine brand. 0E: KX model 00: Unknown 79: UF model 19: Xerox model
78
KX-FT932BR-B
6 7
Detailed description of the Problem with the service line. possible causes (Similar to troubleshooting items No.2 and No.3.) The troubleshooting procedure for each error code will be printed on the communication result report.
79
KX-FT932BR-B
CROSS REFERENCE: Operation Panel Section(P.113) ADF (Auto Document Feed) Section(P.93) Maintenance(P.129)
80
KX-FT932BR-B
Note: 596: Transmit level set represents a service code. (Refer to Service Function Table(P.57).)
81
KX-FT932BR-B
Note: 596: Transmit level set represents a service code. (Refer to Service Function Table (P.57).) Remarks: Regarding the reception problem, we have investigated the conceivable causes in the flow chart except for the software-related errors. However, some troubles may occur due to the software-related problems such as OUT OF PAPER when the fax switches to the memory receiving mode and the memory capacity becomes full of the unprintable data. In this case, error messages [MEMORY FULL] and its main cause, for example CHECK PAPER are displayed on the LCD. Once you solve the main problem, [MEMORY FULL] will be cancelled and the reception problem will be resolved. LCD display messages indicating the error causes are shown below. COVER OPEN UNIT OVERHEATED (COVER OPEN, etc.)...Reset the unit. PAPER JAMMED Please refer to Error Messages-Display (P.65) for the above items. If it turns out to be a hardware deformity, please check each sensor. (Refer to Test Mode (P.54).)
82
KX-FT932BR-B
83
KX-FT932BR-B
12.3.3.1.5. The unit can copy, but cannot either transmit/receive long distance or international communications
The following two causes can be considered for this symptom. Cause 1: The other party is executing automatic dialing, the call has been received by this unit, and the CED or DIS signal response time is too long. (In most cases, this unit detects the CNG signal and can respond to CED or DIS.) (According to the ITU-T standard, the communication procedure is cancelled when there is no response from the other party within 35 sec, so that the other party releases the line.)
(Cause and Countermeasure) As shown in the chart above, the total handshaking time must be reduced, but because of the long distance connection and linking of several stations, the line connection time cannot be reduced. Accordingly, the following countermeasures should be tried. (A)... As the 45 sec. count is started directly after dialing or directly after the START button has been pressed for models with a START button, the other party should be called manually, if possible. Another possibility is entering two pauses at the end of the auto dial number on the transmission side. Then the count start time can be delayed for 2 pauses (about 10 sec.). Cause 2: Erroneous detection because of an echo or an echo canceler.
(Echo/Echo Canceler) The signal from FAX1 reaches FAX2 via stations 1 and 2, but the reflection signal at station 2 also returns via station 1 (echo). As the distance between station 1 and station 2 is far, the echo returns to FAX 1 at a max of 600 msec after transmission. There is a possibility that this signal is detected erroneously as the signal from FAX2. For a normal call, there is also a possibility that the echo of their own voice will make the call difficult to understand. For this reason, each station (station 1 and station 2) attaches echo cancelers (S1 and S2) for international lines or long distance lines. For the echo canceler, the level of the transmission signal from FAX 1 is compared with the level of the reception signal from FAX2. When the transmission signal is larger, S1 is closed while S2 is opened when it is smaller. In other words, for transmission from FAX1, S1 is closed and S2 is open, so that the echo does not return to FAX1.
84
KX-FT932BR-B
Service code (594) (Overseas DIS select) Service code (596) (Transmit level set)
detection
Sending side
Communication failure occurs in a long distance communication on the telephone line without an echo canceler. or There are some cases (e.g. Mobil comms.) which cause the collision of TX / RX signals due to the delay / echo and noise of the network / terminal. (Refer to Fig. e)
Service code (598) (Receiving sensitivity) Service code (774) (T4 timer)
Fig. b (Countermeasure by Changing the CED Frequency) Fig. a (Overlapping the Echo of the DIS signal and DCS signal)
85
KX-FT932BR-B
<TX side signal> 2nd / 3rd DCS / Training 2nd / 3rd EOP / EOM / MPS delayed DCS
<RX side signal> & delayed CFR / FTT & delayed MCF / PIP / PIN / RTP / RTN & 2nd / 3rd / --- DIS
(Fig. e)
12.3.3.1.6. The unit can copy, but the transmission and reception image are incorrect
(Long distance or international communication operation) This symptom highly depends on the transmission and reception capability of the other FAX unit and the line conditions. The countermeasures for this unit are shown below. Transmission Operation: Set the transmitting speed to 4800BPS (service mode: code No. 717) or select the overseas mode. Reception Operation: If 80% or more of the reception is incorrect, set the receiving speed to 4800BPS. (Service mode: code No. 718) Refer to Service Function Table(P.57).
86
KX-FT932BR-B
2. Setting up
4. PC setting and recording 1. Set LINE IN to be valid in the volume control setting. Refer to the PC instruction book. 2. Start up the PC software SOUND RECORDER. (This software is bundled to Windows OS, which can create WAV file.) Set the audio format PCM 22.050kHz, 8bit, mono. 3. Click the record button and start recording after acquisition the signal. Note: Not to be wind wave patterns on the wave monitor. Please compress the recording data when you send attaching to E-Mail because the data size will be so heavy. Any software which can create WAV files is available.
87
KX-FT932BR-B
12.4.1. Entering the Remote Programming Mode and Changing Service Codes
88
KX-FT932BR-B
89
KX-FT932BR-B
Code 815 852 853 874 875 880 881 882 961 962 991 994 995 996 998 999
Function Sensor test Print test pattern Top margin DTMF ON time DTMF OFF time History list Journal 2 Journal 3 The time transmitting the false ring back tone The operator calling time Setup list Journal list Journal 2 list Journal 3 list History list Service list ----------------1~9 mm 06~20msec 06~20msec 1:SET 1:SET 1:SET 01~10 x sec 05~30 x sec 1:Start 1:Start 1:Start 1:Start 1:Start 1:Start
Set Value
Remote Setting NG NG OK OK OK NG NG NG OK OK OK OK OK OK OK OK
OK means can set. NG means can not set. Note: Refer to Service Function Table (P.57) for descriptions of the individual codes. Example: If you want to set value in the 004 Transmission report mode, press the dial key number 1, 2 or 3 corresponding to the Set Value you want to select. (1:ON/2:OFF/3:ERROR)
90
KX-FT932BR-B
CROSS REFERENCE: Error Messages-Display(P.65) Simple Check List(P.92) Digital Board Section(P.100) Power Supply Board Section(P.110)
91
KX-FT932BR-B
Printing
See When Coping or Printing, an Abnormal Sound is Heard from the Unit (P.99) Voltage output is abnormal. See Power Supply Board Section (P.110) Keys are not accepted. See Operation Panel Section (P.113) If the electric circuit is the cause, the error mes- See Sensor Section (P.114) sage corresponding to the sensor will be displayed.
Error code is displayed. Cannot talk. DTMF tone doesnt work. Handset/Monitor sound, volume. Abnomal sound from the product
FAX operation
Note: Check according to the sevvice code referring to the Test Mode (P.54).
92
KX-FT932BR-B
Note: (*1) : Refer to Multiple Feed (P.95) (*2) : Refer to How to Remove the Operation Board, LCD and Platen Roller (P.121) (*3) : Refer to Test Mode (P.54) (*4) : Refer to Digital Board Section (P.100) (*5) : Refer to Sensor Section (P.114) (*6) : Refer to How to Remove the Gear Block and Separation Roller (P.127) (*7) : Refer to How to Remove the Separation Holder and Document Feed Support (P.122) (*8) : Refer to Power Supply Board Section (P.110)
93
KX-FT932BR-B
CROSS REFERENCE: Test Mode (P.54) Sensor Section (P.114) Note: (*1) : Refer to How to Remove the Operation Board, LCD and Platen Roller (P.121) (*2) : Refer to Disassembly and Assembly Instructions (P.118)
94
KX-FT932BR-B
Note: (*1) : Refer to How to Remove the Separation Holder and Document Feed Support (P.122) (*2) : Refer to Disassembly and Assembly Instructions (P.118) (*3) : Refer to Maintenance (P.129)
95
KX-FT932BR-B
12.5.4.4. Skew
Note: (*1) : Refer to Maintenance Items and Componet Locations (P.129) (*2) : Refer to Disassembly and Assembly Instructions (P.118) (*3) : Refer to How to Remove the Separation Holder and Document Feed Support (P.122) (*4) : Refer to How to Remove the Operation Board, LCD and Platen Roller (P.121) (*5) : Refer to How to Remove the Image Sensor (CIS) and Feed Roller (P.123)
96
KX-FT932BR-B
CROSS REFERENCE: Thermal Head Section (P.116). Test Mode(P.54) CIS (Contact Image Sensor) Section (P.115). Note: (*1) : Refer to Maintenance Items and Componet Locations (P.129) (*2) : Refer to Disassembly and Assembly Instructions (P.118) (*3) : Refer to How to Remove the Operation Board, LCD and Platen Roller (P.121)
97
KX-FT932BR-B
CROSS REFERENCE: Test Mode(P.54) Digital Board Section (P.100) Note: (*1) : Refer to How to Remove the Lock Lever and Thermal Head (P.124) (*2) : Refer to Maintenance Items and Componet Locations (P.129) (*3) : Refer to How to Remove the Operation Board, LCD and Platen Roller (P.121) (*4) : Refer to How to Remove the Image Sensor (CIS) and Feed Roller (P.123)
98
KX-FT932BR-B
12.5.4.8. When Coping or Printing, an Abnormal Sound is Heard from the Unit
Note: (*1) : Refer to Document Feeder Cleaning (P.138) (*2) : Refer to Thermal Head Cleaning (P.138) (*3) : Refer to Disassembly and Assembly Instructions (P.118) (*4) : Refer to How to Remove the Motor of Gear Block (P.127) (*5) : Refer to How to Remove the Gear Block and Separation Roller (P.127)
99
KX-FT932BR-B
Note: 1. Electrical continuity may have existed at the factory check, but a faulty contact occurred as a result of vibration, etc., during transport. 2. Solder waste remaining on the board may get caught under the IC during transport, causing a short circuit. Before we begin mass production, several hundred trial units are produced at the plant, various tests are applied and any malfunctions are analyzed. (In past experiences, digital IC (especially DRAM and FLASH ROM) malfunctions are extremely rare after installation in the product.) This may be repaired by replacing the IC, (DRAM etc.). However, the real cause may not have been an IC malfunction but a soldering fault instead. Soldering faults difficult to detect with the naked eye are common, particularly for ASIC and RA (Resistor Array). But if you have an oscilloscope, you can easily determine the problem site or IC malfunction by checking the main signal lines. Even if you dont have such a measuring instrument, by checking each main signal line and resoldering it, in many cases the problem will be resolved. An explanation of the main signals (for booting up the unit) is presented below. Dont replace ICs or stop repairing until checking the signal lines. An IC malfunction rarely occurs. (By understanding the necessary signals for booting up the unit, the Not Boot up display is not a serious problem.) What are the main signals for booting up the unit? Please refer to Digital Board Section (P.100). The ASIC (IC1) controls all the other digital ICs. When the power is turned on, the ASIC retrieves the operation code stored in the FLASH ROM (IC2), then follows the instructions for controlling each IC. All ICs have some inner registers that are assigned to a certain address. It is the address bus by which the ASIC designates the location inside each IC. And the data bus reads or writes the data in order to transmit the instructions from the ASIC to the ICs. These signal lines are all controlled by voltages of 3.3V (H) or 0V (L).
100
KX-FT932BR-B
The signal lines that must be normal for the system to boot up are listed here [List 1]. For signal lines other than these, even if they malfunction they do not directly affect booting up the system.
101
KX-FT932BR-B
NG Wave pattern
102
KX-FT932BR-B
Remarks: When you use an oscilloscope to judge whether a signal to be tested is normal or NG, perform the signal check in exactly the same order as in [List 1]. (If the ASIC fails to access the ROM, the ASIC cannot access DRAM normally.) The digital circuit actually operates according to the timing combinations of these signals. If the timing of these signals is even slightly delayed, the circuit will not work. Nor will it if the IC is defective and the output voltage level is not normal although the timing of these signals is accurate enough to meet the specifications. (Make sure that your oscilloscope is calibrated before starting a test.) Therefore, it is imperative to confirm whether each IC outputs the signal at the correct level. (See the I/O Pin No. Diagram.) The signal level should be constantly output at between 3.3V (H) and 0V (L) as described earlier.
103
KX-FT932BR-B
104
KX-FT932BR-B
105
KX-FT932BR-B
106
KX-FT932BR-B
12.5.5.3. NG Example
107
KX-FT932BR-B
108
KX-FT932BR-B
4. No tone dialing
109
KX-FT932BR-B
12.5.7. Power Supply Board Section 12.5.7.1. Key components for troubleshooting
Check the following parts first: F1, D10-D13, C5, and Q1. This comes from our experience with experimental tests. For example: power supply and lightning surge voltage test, withstanding voltage test, intentional short circuit test, etc. Caution: If you find a melted fuse in the unit, do not turn on the power until you locate and repair the faulty parts (except for the fuse); otherwise the fuse will melt again and you cannot pinpoint the faulty point. In most cases, the symptom is that nothing is output. It is more likely that the fault is in the primary side rather than the secondary side. Check the primary side first.
110
KX-FT932BR-B
111
KX-FT932BR-B
112
KX-FT932BR-B
113
KX-FT932BR-B
114
KX-FT932BR-B
115
KX-FT932BR-B
116
KX-FT932BR-B
117
KX-FT932BR-B
CROSS REFERENCE: A-1 : How to Remove the Operation Panel Block (P.120) A-2 : How to Remove the Operation Board, LCD and Platen Roller (P.121) A-3 : How to Remove the Separation Holder and Document Feed Support (P.122) A-4 : How to Remove the Image Sensor (CIS) and Feed Roller (P.123) A-5 : How to Remove the Lock Lever and Thermal Head (P.124) B-1 : How to Remove the Bottom Frame (P.125) B-3 : How to Remove the Gear Block and Separation Roller (P.127)
118
KX-FT932BR-B
CROSS REFERENCE: B-1 : How to Remove the Bottom Frame (P.125) B-2 : How to Remove the Analog Board, Digital Board, Power Supply Board and Power Cord (P.126) B-3 : How to Remove the Gear Block and Separation Roller (P.127) B-4 : How to Remove the Motor of Gear Block (P.127)
119
KX-FT932BR-B
120
KX-FT932BR-B
14.2.2. How to Remove the Operation Board, LCD and Platen Roller
121
KX-FT932BR-B
14.2.3. How to Remove the Separation Holder and Document Feed Support
122
KX-FT932BR-B
14.2.4. How to Remove the Image Sensor (CIS) and Feed Roller
123
KX-FT932BR-B
124
KX-FT932BR-B
125
KX-FT932BR-B
14.2.7. How to Remove the Analog Board, Digital Board, Power Supply Board and Power Cord
126
KX-FT932BR-B
127
KX-FT932BR-B
128
KX-FT932BR-B
15 Maintenance
15.1. Maintenance Items and Componet Locations
15.1.1. Outline
MAINTENANCE AND REPAIRS ARE PERFORMED USING THE FOLLOWING STEPS. 1. Periodic maintenance Inspect the equipment periodically and if necessary, clean any contaminated parts. 2. Check for breakdowns Look for problems and consider how they arose. If the equipment can be still used, perform copying, self testing or communication testing. 3. Check equipment Perform copying, self testing and communication testing to determine if the problem originates from the transmitter, receiver or the telephone line. 4. Determine causes Determine the causes of the equipment problem by troubleshooting. 5. Equipment repairs Repair or replace the defective parts and take appropriate measures at this stage to ensure that the problem will not recur. 6. Confirm normal operation of the equipment After completing the repairs, conduct copying, self testing and communication testing to confirm that the equipment operates normally. 7. Record keeping Make a record of the measures taken to rectify the problem for future reference.
129
KX-FT932BR-B
6 7
3 4
Feed Rollers (Ref. No. 30, 78) Thermal Head (Ref. No. 58)
3 months 3 months
* These values are standard and may vary depending on usage conditions.
130
KX-FT932BR-B
<Fig. A>
131
KX-FT932BR-B
15.2.2.1. TX Mode
Swing Gear A engages Gear TX and conveys its drive power to the Separation Roller Gear for pre-feeding documents.
Fig. B: TX mode
15.2.2.2. RX Mode
Swing Gear B engages Gear RX and conveys its drive power to the Platen Roller Gear for printing the received data.
Fig. C: RX mode
132
KX-FT932BR-B
133
KX-FT932BR-B
134
KX-FT932BR-B
15.2.3.2. Scanning
15.2.3.3. Printing
135
KX-FT932BR-B
15.2.3.4. Copying
136
KX-FT932BR-B
15.3. Jams
15.3.1. Recording Paper Jams
1. Open the top cover by pressing the top cover release button ( ).
Note: Do not pull out the jammed paper forcibly before opening top cover. 4. Install the recording paper and close the top cover securely by pushing down on both sides. (See page Installing the Recording Paper (P.51))
137
KX-FT932BR-B
15.4. Cleaning
15.4.1. Document Feeder Cleaning
Clean the document feeder when: - Documents frequently misfeed. - Smudges or black/white lines appear on the original document when sending or copying. 1. Disconnect the power cord and the telephone line cord. 2. Open the top cover by pressing the top cover release button ( ).
15.4.2.
If smudges or black/white lines appear on a copied/received document, check whether there is dust on the thermal head. Clean it to remove the dust. 1. Disconnect the power cord and the telephone line cord. 2. Open the top cover by pressing the top cover release button ( ) and remove the recording paper.
) with a cloth moistened with isopropyl rubbing alco) and scanner glass ( ) with a soft and dry cloth.
hol, and let all parts dry thoroughly. Clean the white plate Caution: Do not use paper products, such as paper towels or tissues.
3. Clean the thermal head ( ) with a cloth moistened with isopropyl rubbing alcohol, and let all parts dry thoroughly. Caution: To prevent a malfunction due to static electricity, do not use a dry cloth and do not touch the thermal head directly.
4. Connect the power cord and the telephone line cord. 4. Connect the power cord and the telephone line cord. 5. Close the top cover securely by pushing down on both sides. 5. Install the recording paper and close the top cover securely by pushing down on both sides.
138
KX-FT932BR-B
16 Miscellaneous
16.1. Terminal Guide of ICs Transistors and Diodes
16.1.1. Digital Board
139
KX-FT932BR-B
140
KX-FT932BR-B
16.2.1. Preparation
PbF (: Pb free) Solder Soldering Iron Tip Temperature of 700F 20F (370C 10C) Note: We recommend a 30 to 40 Watt soldering iron. An expert may be able to use a 60 to 80 Watt iron where someone with less experience could overheat and damage the PCB foil. Flux Recommended Flux: Specific Gravity 0.82. Type RMA (lower residue, non-cleaning type) Note: See About Lead Free Solder (PbF: Pb free) (P.7).
2. Make a few cuts into the joint (between the IC and its pins) first and then cut off the pins thoroughly.
When you attach a new IC to the board, remove all solder left on the land with some tools like a soldering wire. If some solder is left at the joint on the board, the new IC will not be attached properly.
141
KX-FT932BR-B
*Check the accuracy of the IC setting with the corresponding soldering foil. 2. Apply flux to all pins of the FLAT PACKAGE IC.
3. Solder the pins, sliding the soldering iron in the direction of the arrow.
142
KX-FT932BR-B
143
KX-FT932BR-B
144
KX-FT932BR-B
MEMO:
145
KX-FT932BR-B
17 Schematic Diagram
17.1. Digital Board
4M DRAM
IC4
MOTOR BLOCK
+24V
M
F1 1.25A
R1 Q1
820
R2 1.5K 3/4W
A[4] A[5] A[6] A[7] RBA[0] RBA[1] RBA[2] RBA[3] RBA[4] RBA[5]
Q2
10 11 12 13 16 17 18 19 20 9
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9R
IC2
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18
+5V 220
RXE
BR4
+3.3VD
RA109
R3
CN3
D501
COM RM3 RM2 RM1 RM0 1 2 3 4 5
10V
10V
9 10 11 12 13
GND
8 7
DG
RM3
6
A18
RM2
5
RBA[5]
DG
RM1
4
RD
WR
RM0
+24LV
BR5
Z0.1u
D502
C104
2 1
BR1
D505
BR6
10k
IC7
DG
A[0] A[1] A[2] A[3] A[4] A[5] A[6] A[7] A[8] A[9] A[10] A[11] A[12] RBA[0] RBA[1] RBA[2] RBA[3] RBA[4] RBA[5]
A[0] A[1] A[2] A[3] A[4] A[5] A[6] A[7] A[8] A[9] A[10] A[11] A[12] RBA[0] RBA[1] RBA[2] RBA[3] RBA[4]
20 19 18 17 16 15 14 13 3 2 31 1 12 4 5 11 10 6 30 32
D0 D1 D2 D3 D4 D5 D6 D7
21 22 23 25 26 27 28 29
D0 D1 D2 D3 D4 D5 D6 D7
WE 7 VDD 8 VSS 24
4 3
14 15
3 2 1 PG
BLEEDER_ON
(1) (2)
680 2W
R172
16
PG
+3.3VD
+24VF
+24VF
8 7 6 5
1 2 3 4
C10 K0.1u
+24V
CE1
R102
10K J2
IC11
1 INB 2 INA VCC 5
R12 4.7K
GND
4 OUT
R11 2.2K
DG
C105
Z0.1u
DG
C11 ( ) NC
(7)
HEADON RBA[5] RBA[4] RBA[3] RBA[2] RBA[1] RBA[0] A[12] A[11] A[10] A[9] A[8]
DG
Q6 Q4 +2.5VD Q5
(8)
RXE TH-TMP A[7] A[6] A[5] A[4] A[3] A[2] A[1] A[0]
CN4
COM LATCH STB1 GND +3.3V TM CLOCK GND STB2 DATA COM 1
PG
R13
2 3
100
C12
4
+3.3VD
Z0.1u
5 6 7 8 9 10
THLAT
RA102 L21 0
1 2 3 4 8 7 6 5
RBA6
(9) (10)
C178 Z0.1u C177 Z0.1u
100
STB1 STB2
( )
( )
C13
R18
R19
R20
C14
11
( )
J100p
(11)
R150 2.2K
108 107 106 105 104 103 102 101 100
C150
99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73
109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138
XWDERR
+5V RA110
3 4 2 1
R151 4.7K
4.7k
CUT_POS
DG
+5V 4.7k
4 3 1 2
ACK_EN CISON RLY CUT_POS KSTART KLATCH KSCLK KTXD KRXD OPRESET
R152 +24V +24V 22K C155 +5V 4.7K +3.3VD R153 Z0.1u
3 4 2 1
1
DG
RA111
C31
NC
DG
OPE-PANEL BLOCK
+24LV
DG
1 2 3 4 5 6 7 8 9 10
F2
0.25A
+3.3VA 10
VDD3.3V VSS
CN7
CA102
VSSA VDDA3.3 AIN1 AIN2 AIN3 AMON VSSA X32OUT X32IN 3.3V/BATTIN XBACKEN XRAMCS 3.3V/BATTOUT 2.5V/BATTIN FTG F1 F2/OP FA/OP CPC/IP RVN/IP IRDATXD/IOP81 IRDARXD/IOP80 TXD/IOP30 RXD/IOP31 XRTS/IOP32 XCTS/IOP33 VDD2.5V TONE1 TONE2 VOL1REF VOL2OUT VOL3IN XNMI
VSS VDD3.3V XDRESET VDD5.0V VSS XRESETI XWDERR THDAT THCLK THLAT STBNP RM0/IOP00 RM1/IOP01 RM2/IOP02 RM3/IOP03 RXE/IP04 TM0/IOP10 VDD2.5V VSS TM1/IOP11 TM2/IOP12 TM3/IOP13 TXE/IP14 KSTART KLATCH KSCLK KTXD KRXD FMEMCLK/IOP24 FMEMDI/IOP25 ADSEL1 VDDA2.5V VREFB VCL VREFT VSSA
VSS VDD3.3V XRESET STB3 STB2 STB1 RBA5/IOP96 RBA5/OP RBA4 RBA3 RBA2 RBA1 RBA0 ADR12 ADR11 ADR10 ADR9 ADR8 ADR7 ADR6 VDD2.5V VSS ADR5 ADR4 ADR3 ADR2 ADR1 ADR0 XWR XRD XR0MCS DB7 DB6 DB0 VDD3.3V VSS
DG
C151 Z0.1u
C176 Z0.1u
72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 VSS 37
IC1
VSS VDD3.3V DB5 DB1 DB4 DB2 DB3 XRESCS2/OP71 XCAS2/IOP44 XCAS1/IOP43 XRAS/IOP42 XMDMCS XMDMINT TEST4 TEST3 TEST2 TEST1 XTEST VDD3.3V VSS XIN XOUT VDD2.5V ADR13/OP ADR14/OP ADR15/OP XDPRBE/MUX/OP53 XHSTWR/IOP41 XHSTRD/IOP40 XWAIT/IOP60 20KOSC/IOP56 MILAT/IOP47
1 2 3 4
RA106
(12)
100
8 7 6 5
(13) (14)
J100p
(15)
3.3K
FMEND0/IOP26
R59
Z0.1u
C158
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
K1000p
R154
RA108
3.3k 4
DG
DG
R158
1 2 3 4
8 7 6 5
47K
470
RA101
(16)
C167 Z0.1u XNMI
C159
AIN2
2 1
0 100
3 4 2 1
22K
C161 K0.1u
AMON X1 BR2
2 1
L2
KSCLK OPRESET
J100p
RA112 47K
H/L control NC ( )
R155
DG
+3.3V/BATIN
C162
R57
C51
DG
R58
( ) NC
PWRCNT
C165
DG
Z0.1u
DG
HEADON MDMRST CPC PAPER JAM HSTXMUTE BELL TELRXEN PSHORT MDMTXEN
R70 C70
AIN1
C77
NC ( )
NC ( )
Z1u
Q9
FTG F1
LEDON
TO POWER SUPPLY
CN1
PCONT +6V +6V GND GND GND +24V +24V +24V 9 8 7
DG
+5V
+5V
+5VA +5VA
(22)
FTG
(23)
+3.3VD TO +2.5V
+2.5VD
+2.5VD
C71
+6V
+3.3V/BATIN TO +2.5V/BATIN
+2.5V/BATIN +3.3V/BATIN
+6V
DG
DG
+3.3VD
+3.3VD
Q10
6 5 4
PG
IC15
Z1u Z1u 6.3V47u C75
VOUT VIN 3 VSS 1 1 2 3
IC3
VDD GND VOUT VDET 4 CE 5
+5V
DG
+24V
F36K
3 2
C74
CA104
C78 6.3V47u
Z0.1u C80
Z0.1u
J100p
Z0.1u
C79
C73
C81
R74
( ) NC
Z0.1u 4.7M C87 R79
R73
DG DG DG DG DG
RESET
DG
2 1
C76
DG
DG
J1
R77
3 4
2.2K
R71
33K
R80
(24)
146
KX-FT932BR-B
4M FLASH FOR VOICE A[0] A[1] A[2] A[3] A[4] A[5] A[6] A[7] A[8] A[9] A[10] A[11] A[12] RBA[0] RBA[1] RBA[2] RBA[3] RBA[4]
20 19 18 17 16 15 14 13 3 2 31 1 12 4 5 11 10 6 30 32
IC6
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 CE OE D0 D1 D2 D3 D4 D5 D6 D7 21 22 23 25 26 27 28 29
+24LV +24LV
TO ANALOG CN2
1 2
DG
C106
MDMTXEN TONE1EN ( ) NC
C94 Z0.1u +5VA
3 4
PAPER
+5VA
14
IC10
1 2 VDD 13 12 11 10 9 VSS 8
2.2K
RBA[5]
L12
3
HSRXEN
CPC JAM
4.7K
R36
NC NC
330K
TELRXEN
RLY
R40
A18
DG
+5VA
6 7 8 9
( ) NC
R127
C127
DG
6 7
BELL HOOK
4.7K
V+
A B
J100p R129
C115
IC9
8
4 5
+5VA R38
PSHORT
( ) NC
+2V L9
C117
( ) NC
3 4
DG
D504
( ) NC
V-
C126
NC
L10 L11
DG
+2V C125
R128 36K
NC
DG
DG
R130
24K
HSTXMUTE
15 H/STX_MUTE
R124
K0.1u
47K
NC
C128
16 H/SRX
K0.1u
C118 C119
( )
R118
C124
Q18
C129 Z0.1u
( )
NC
( )
C123 NC R119
( )
NC R120
NC ( ) NC
( )
( )
NC
(7) (8)
NC
NC
2 3 4 5 6 7 8
DG
C120
R113
R114
R115
( )
NC
( )
NC C122
( )
NC
( ) ( )
NC NC R116
(
( ) NC
Q17 C121
DG
)
DG DG
ACK_EN R121 ( ) NC
( )
DG
NC
+3.3VD
(9) (10)
MDMCS
D[7] D[6]
L18 L17
( ) NC
( ) NC
L4
L3
C238
Z1u
( ) NC
( ) NC
R225
R226
C224
20K
( ) NC
80 79 78 77 R231 76 75 0 74 C241 Z0.1u 73 C239 C240 Z0.1u 72 Z0.1u 71 70 R229 C237 69 J10p 1K 68 67 C236 J10p 66 65 L7 64 0 63 62 R228 47K 61 60 C233 59 C235 16V10u Z0.1u 58 57 56 R227 55 22 C232 C234 Z0.1u 54 J100p 53 52 51 ( ) NC
C230 ( ) NC
10K
Z0.1u
(11)
D[0]
C229
Z0.1u
K0.068u
C226
C251
( ) NC
X3
32.256MHz
DG
IC16
1 VCC 5
C225
R223 3.9K
( ) NC
DG
L6
C221 K0.22u
(12)
SPMUTE
A[5]
2 3 GND 4
MDMCS
XTEST
WRn RDn CSn VDDo77 AVDD ENABLE_VREG18D VBG AVSS VSSo72 VSS71 VDD70 XTLO XTLI TEST GPI2 GPI1 GPI0 GP02 GPO1 RINGDn IA1_VDD IA_AVSS59 IA1_SPKRM IA1_SPKRP IA1_TXP IA1_TXM IA1_AVDD IA1_VC IA1_Vref IA1_HSMIC_BIAS
NC
+3.3VD
DG
DG
C220
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
(14)
DG
C203
X2 C173 D10p
( )
VSS1 VDD2 VSSo3 VDDo4 EYEXY/XCLK RESERVED6 RESERVED7 PIA_RESETn PIA_STROBE PIA_TXSIN PIA_RXOUT PIA_CNTRL_SIN PIA_CLKIN PIA_SCLK IA1_SCLK IA1_CLKIN IA1_CNTRL_SIN IA1_TESTC IA1_RXOUT IA1_TXSIN IA1_STROBE IA1_RESETn RESERVED23 IA_AVSS RESERVED25 RESERVED26 RESERVED27 RESERVED28 RESERVED29 RESERVED30
C174
D10p
C209
J33p
4.7K
( ) NC
TONE1EN
C215
( ) NC
C211
DG
C212
C204
R232
C205 Z1u
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
C210
R217
( ) NC
R216
DG
(16)
DG
C206 Z0.1u
DG
C208
( ) NC
( ) NC
DG
120K
C169 K1000p
R178
1K
DG
SPMUTE
CIS BLOCK
LEDON CISON F1 FTG
(22)
+3.3VD
AIN1
+5V
RA113
3.3K
22K
2.2K
RA107
220 4
R94
(23)
R90
IC12
1 2 3 CD FC2 FC1 VIN VO2 GND VCC VO1 8 7
120K
2 1
R142
10K
TO SPEAKER
CN9
1
3 4
+5V TO +2V
+2V
+2V
R93
SP+ SP-
2 1
( )
6 5
( )
NC
R75
12K
NC ( )
Z0.1u
R95 1.5K
R96
C90
C91
C143
DG
K1000p 9.1K
DG
NC
NC
NC ( )
C93
DG
K0.1u R140
15K
R141
6.3V47u
8.2K
C85
R76
( )
C84
C86
( )
CN8
LEDVCC
LEDGND
FI(DATA)
FTG(CLK)
+3.3V
GND
AIN(SI)
DG
DG
DG
(24)
147
NC
C144
( ) NC
( )
DG
(15)
NC
BLEEDER_ON
IC5
RESERVED35 RESERVED34 RESERVED33 RESERVED32 RESERVED31
R164
RESERVED45 RESERVED44 RESERVED43 RESERVED42 RESERVED41 IA_AVSS40 RESERVED39 RESERVED38 RESERVED37 RESERVED36
K4700p
C202 Z0.1u
C201
C242
( ) NC
C243
( ) NC
L20
R219
DG
( )
NC
NC ( )
10K
(13)
MDMRST
R200
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
( )
C219 L19
NC
K0.1u
DG
C200
( ) NC
R221 4.7K
C216 K0.22u
KX-FT932BR-B
(1)
R10 120K C8 J270p 10K +24VA
+2.0V
R2
C4 50V4.7u C7
[1]
IC2-1
1
2 3
C13
T1
3 2
R41
150 2W
(2)
Z0.1u
K0.01u
4.7V
( ) NC
D1
R26
D3
C29
BEAD
AG
AG
Q13
AG
C63
+12V
K0.033u
L4 BEAD
L3
270 1/4W
C27
NC
R27
( )
( ) NC
C66
( ) NC
R87
( )
(3)
NC
C78
(4)
( ) NC
AG
( ) NC
R22
12K
K1500p
AG
120K
C14
R15
K0.015u
(5)
R23
AG
C19
+5V
R24
( ) NC
560K 50V4.7u J22p C28
CN1
+24V 1 AG 2
AG
(6)
C32 R39 J150p 330K +5VA +2.0V R47
7 5
IC2-2
+5V 3 PAPER 4
LINETX 5
L12
C12
TONE1 6
R17 110K
R21 39K
C25 K0.022u
IC1-1
K0.1u
RLY CPC JAM 7 8 9
8 1 4
(7)
( )
C35
NC
R36
2.2K
C31 Z0.1u 0
AG
DA2
1A2K
AG
1K 2A
L1
LINERX 13 MONRX 14 H/STX_MUTE 15 H/SRX 16
NC
L13
BEAD
(8) (9)
PAPER SENSOR SW
SW1
2 4 1 3
JAM SENSOR SW
SW3
2 4 1 3
R32 51K
C30 K0.1u
(10)
(PULL UP AT DIGITAL)
Z0.1u 1
AG AG
( ) NC
(PULL UP AT DIGITAL)
( )
NC HOOK SENSOR SW
+5V 22 +24VA R100 R1 100
4 5 6
AG
(
R30 18K
AG
SW2
1
FG2 AG
) Q4
NC
+24V
+5VA
(11)
R37 R31
Q1
(PULL UP AT DIGITAL)
AG
+2.0V
( ) NC
220K
C16
R25
10K
R19
10K
+12V
( ) NC
R8
6.3V47u
NC
AG
(
Z0.1u
) Q5
AG
C10
6.3V47u R9
16V10u
C71
( )
Z0.1u R20
( ) NC
10K
220K
C24
AG
AG
C15
C20
AG
C3
C6
AG
148
NC NC
KX-FT932BR-B
+5VA
( ) NC
( ) NC
R86
NC
C68
( ) NC
R83
PC6
E K
NC
D10
FAX TX signal
2 3
( )
D13
(1)
R88
Q12
1 4
NC
( )
FAX RX signal
()
( ) NC NC
C67
R84
D15
NC C52 ( ) C53 ( ) NC NC
R85
AG
( ) NC
( ) NC
( ) NC
(2)
+5VA PC4 PC2 NC
JJ1
L31
NC
AK C
AK KA
L19
KA E
NC
2 3
300V
SA1
1 a 2 b
E
AG
C80
NC ( )
0
C43
NC ( )
4
(3) (4)
+5VA
R105
R54 0 JJ2 0
L32
3
POS1
C79
( ) NC
NC ( )
JJ3
AG
(5)
C
JJ4 0
( ) NC
AK KA
PC1
E
AG
2 a1
D4 0
D5 0
L26
( ) NC
12
R106
(6)
R102
AG
NC
(7)
R48 6.2K
R61
DA1
T3
NC
3
R62
NC
NC
NC
( ) NC
1A
R59 ( )
2K 1K2A
( )
4 2 1
( )
( )
C65
NC
AG
AG
+5V
2
(8) (9)
R60 10K
C51 K0.1u D8
RLY1-2
+5VA
AG
6.3V47u
IC1-2
12K
C41
K0.027u
AG
(10)
( ) NC
7 5
12K
C40
Q7
CN2
L21 L23 L24
1 HSMIC 2 HSSP+ 3 HSSP4 HSMIC +
220K
( ) NC
C46
R40
R44
C37
AG
R52
22
L16
C48
+5VA
L22
AG
R51
47K
NC
K4700p
C49
K0.1u
18K C39
K0.01u
(11)
C42
C33
Q6
R46
C44
( ) NC
( )
DA3
AG
C45 16V10u
AG
R43
AG
330
149
KX-FT932BR-B
R19 C17 TO LCD 4.7 Z0.22u MICR17 2.2K +5V R16 ( ) NC LED1
C28 ( AG NC R35 ( ) NC C25 ( ) NC C99 ( ) NC ) NC R39 ( ) NC R37 ( ( ) NC C22 ( NC TO MIC MIC+ ) ) ) NC Q4 C26 AG
DG
C1
Z0.1u C2 ( ) Z0.1u C3
6.3V220u
+5V 2 AG AG
DG 3
R1
KLATCH 5
R2
KRXD 6
KTXD 7
R3
KSCLK 8
R4
R5
NC
MICIN 1
R48
CN1
TO DIGITAL
+5V
R47
CN2
+5V
C4
+5V R22 R20 100 C16 Z0.1u C19 K0.01u +5VL 4.7K SW39
4 3 1 2
C15
R50 33
KSL0 KSL1 KSL2 KSL4 KSL3
1 KSL2 2 LED6 3 KIN1 4 LED7 5 XLED8 6 XLED9 7 KIN2 8 KIN3 9 XLED10 10 KSL3 11 KIN4
+5V +5VL
Z0.1u
34 LATCH 35 START 36 LED2 37 LED3 38 LED4 39 VSS-39 40 VDD-40 41 LED5 42 KIN0 43 KSL0 44 KSL1
IC1
LED1 22 XLED15 21 XLED14 20 XLED13 19 VSS-18 18 VDD-17 17 XLED11 16 XLED12 15 KIN7 14 KIN6 13 KIN5 12
DOCUMENT TOP SW
KIN0
KIN1
KIN2 KIN3
KIN4
R23
4.7K
KIN1 KIN6 KIN5
KIN0
KIN4
KIN3
KIN2
KIN7
C20
KSL0
7 SW7 SW12 SW17 SW22 8 MONITOR NAVI DOWN SKEY 3 SW27 MENU SW32
COPY
SW2
NC PLAYBACK ( ) SW37
TP1 CN5
NAVI UP SW23 SKEY 2 SW28 AUTO ANSWER SW33 NC RECORD ( ) SW29 PAUSE SW18
KSL1
4 SW8 SW13 9
STOP
SW3
KSL2
2 SW9 SW14 3 FLASH SW19 NAVI RIGHT SW24 SKEY 5 SW34
TP2
SW4
KSL3
5 SW10 SW15 6 REDIAL SW20 NAVI CENTER SW25 SKEY 1 SW30 SKEY 4 SW35
CALLER ID
SW5
KSL4
K0.01u
150
0 # SW16 SW21 SW6 SW11 NAVI LEFT BOARDCAST SW26 SKEY 6 SW31
+5V
R21
NC
SW38 100
ERASE ( ) SW36
1 2 4 3
FAX/START
SW1
BEA1
C8 220
D1
R5 20K
Q2 R19 10
47K
Q23 R7 R5 560
0.001
R14 100K
C15 100p
R28 6.8K
R27
D3
8.2K
R9 R23 0 D23
PC1
D22
C109
D107
D110
PC1
R115
R111 1K
R409
C112
C115 0.1
( ) NC R113 7.5K
IC401
R410 C410 ( ) ( ) NC NC
R413 ( ) NC
R412 R411 ( ) ( ) NC NC
151
FG LIVE C7 NEUTRAL 0.0033
C5 18p
F1
D17
R23 0
D20
D9 C22 ( ) NC D4 C20 ( ) NC
C4 ( ) NC D13
C3 ( ) NC D11
C10
D105
180K
C23 ( ) NC D12
C21 ( ) NC D10
Q101 1 N.C.
C411 0.22
CNJ2
9 24V
8 24V
7 24V
3 6.5V
2 6.5V
6 GND
5 GND
4 GND
KX-FT932BR-B
MEMO:
152
+5VA CN8 BOND C144 X1 32.7 1 8 R94 R93 C115 IC9 4 5 R128 IC12 1 4 C142 C235 CN2 8 5 C90 Q14 BAT1 R126 L9 R125 C114 C117 C84 9 1 7 C85 J1 CN9
CN1
R10 C73
C11
Q7
C10
8 RA107 R95 E C92 R178 RA108 C211 TEST C212 X2 DG PCB-CH RA109 1 C102 28 R229 X3 32 17 C234
C72
R1
1.25A F1
C74
L10 C86 R76 C116 L12 R75 L11 C126 C127 R129 C125 R127
C12
IC15
C75
CN4
C79
R3
C78 IC3
C31
CN3
RA111
B 14
IC10 1
CN5
CN6
R172 10 1 J2 1 16
CN7
14 C103
CN10
PFUP1677Z
A
KX-FT932BR-B: Digital Board (Component View)
PbF
16
YELLOW
BLUE
153
11
R227 AUTO-CH
L18
C141
D502
D501
R142
R2
E Q2
16
KX-FT932BR-B
KX-FT932BR-B
1 CN9 CN8 CN1 +6V AMON R78 R131 C119 Q11 A B E R153 +3.3VD R11 R19 Q5 E R13 AIN2 L21 C113 R216 C208 C215 C209 C167 C161 CA102 144 C155 R58 C154 IC1 C13 R18 XNMI R161 R164 R77 C165 C162 FTG C158 1 R124 R123 C210 R217 L20 L19 C242 C243 30 C173 R162 R163 XTEST C175 C174 C207 R214 RA106 72 EYECLK D3 EYESYNC C176 C177 80 100 1 XCLK/EYEXY C206 D2 A3 A2 A0 D1 A1 MFCS A15 CE1 C205 WR 1 3 R102 RD A10 ROMCS C178 D4 D5 73 A16 A12 A11 5 IC11 A18 108 109 C153 C151 C30 31 +2.5V/BATIN C168 C171 +2V R158 36 37 RA102 C159 R154 C14 R155 R20 C160 R152 D503 R156 Q9 E Q4 E R12 +24VF +24V Q6 E DG R80 +5VA C164 C163 R79 C87 C112 C118 +3.3V/BATIN
7 9 1
C140
C128
D504
C216
CN4
C221
PG 9
C226
C217 C219 R219 C220 C231 C230 R221 C222 C229 R233 R223
C202
R57 C50
C203
C122 D6 A5 8 D0
Q17 Q18
154
C240 C241 L4 7 L6 D7 A4 A6 A7 A8 C105 4 CE2 A9 A17 +24LV
R226
11
R130 HOOK R38 BELL / DCN P-SHT JAM CPC R36 RLY R40 TONE1 LINETX PAPER R34 +5V
C233 R228
DG
C238 C239
R231
L3
R120
R114
C123
R121 1
C120
R113
CN10
CN7
10
PbF
PFUP1677Z
A
KX-FT932BR-B: Digital Board (Bottom View)
KX-FT932BR-B
CN3
SW1
SA2
J30
POS1
L33
SA1
C28
SW3
CN4
C67
JJ3 J5 JJ4
R54
J29
C78
J19
J14
J20
C52
C53 D15
R105
PC4
J10
J11 J8
R38
R62
R45
D5
D4
PC1 J6 PCB-CH J4 J7 T3
C68
RLY1
T1
C71
R41
C15
C6
J13
CN2
PFUP1678Z
C47
C10
JJ5
J1
PbF
155
CN1
KX-FT932BR-B
+24
R8 PPR CPC R60 R25 LTX B/D RLY +5V PST LRX TON JAM MUT HOK MRX R30 R33 L1 R31 R46 R37
E
R47 R100 C33 16 R29 R28 Q3 C25 Q2 C12 R17 Q5 R104 +24VA R51 C79 Q6 E C39 R52
E
R2 1 1 R39 C32 R48 C16 Q1 E C35 C24 C20 R19 1 C50 C51 Q8 R20
E E
16
DA2
L13 C31
PFUP1678Z
R57 R49 C34 R42 R32 8 R40 L16 R43 C30 C46 R55 R61 R11 C E C +12V C49 PC1 C9 DA1 AK KA AK R35 R24 5 L7 IC2 R63 C80 8 Q13
E
R50 C40
C48
R56
PbF
C44 L4 C7 4 PC4 E KA L3 C23 C22 C17 R13 C13 1
C41
156
C65 R59 L24 L22 C29 DA3 Q7 C63 R83 R84 R85
D10
L23
C18 R22
R102
L21
Q12
E
A PC6 K L25
C43
PFUP1560Z
PbF
J6 J2 J1
SW5
SW34 S5
J11 J10
SW27 S3 REDIAL J16 SW8 SW15 6 4 SW10 5 SW20 J8 J9 SW26 BROADCAST J17 J20 SW7 7 SW12 8 SW13 9 SW18 C3 J35 1 SW6 * SW11 0 SW16 # SW17 CN1 MONITOR 10 SW22 SW21 SW25 SW24 SW23
SW31 S6
157
PAUSE
STOP
PCB-CH
SW3
C99
SW32 MENU
COPY
FAX/START
SW2
SW1
KX-FT932BR-B
MIC-
PbF
PFUP1560Z
12 11
IC1
44
C16 22 R18 23
KX-FT932BR-B
33 34
SW39
C15
MIC+
158
KX-FT932BR-B
D105
PbF
VR101
J103
C109 D101
J101
(COMPONENT VIEW)
(BOTTOM VIEW)
R8
D5
Q1
C8
R7 D7 D17 C10 R6 R14 C15 R26 R28 Q23 D27 Q22 R27 C13 Q2 C14 R25 C16 R31 C5 J1 R21 R24 J3
PC1
PRI.
R2 R3 R4
J4
T1
D20
MPW7025
R19
D9
BOND
C23 D12 D3 D10 D11
R11
R9 D23 D22
C7 C111 R110 R117 R111 R112 R115 C115 R409 R410 D104 C4 C3 D13 C410
C21C22
Q101 R119
N0AB2GJ00005
C112
ZNR1
R113
R114
C411
159
125V 4A F1
R122
L1
C20
C5 J2
BEA1
R5
PCPS0910
Q21
54D1
56-XJ
CNJ2
SEC.
D107
C102
IC401
KX-FT932BR-B
3.
160
KX-FT932BR-B
MEMO
161
KX-FT932BR-B
162
KX-FT932BR-B
163
KX-FT932BR-B
164
KX-FT932BR-B
165
KX-FT932BR-B
20.1.5. Screws
166
KX-FT932BR-B
167
KX-FT932BR-B
Safety
Ref. No. 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Part No. PFKR1087Z1 PFKR1086Z1 PFUV1088Z2 PFHX1834Z PFHG1210Z PFHR1504Y PFUS1588Z PFHR1503Y PFUS1631Z PFUV1105Z2 PFDF1017Z PFDR1045Z PFUS1587Z PFJS09M27Y
Part Name & Description Remarks GUIDE, RIGHT GUIDE, LEFT COVER, DOCUMENT GUIDE READ SHEET (WHITE PLATE) RUBBER, SEPARATION COVER, SEPARATION HOLDER SPRING, SEP. HOLDER COVER, DOC. FEED SUPPORT SPRING, DOC. SUPPORT COVER, OPERATION PANEL SHAFT ROLLER, DOCUMENT SUB SPRING, DOCUMENT SUB ROLLER CONNECTOR, 9 PIN S S S
S S S S S S S
168
KX-FT932BR-B
Safety
Part Name & Description Remarks IC IC IC IC IC IC IC (TRANSISTORS) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) (BATTERY) BATTERY (DIODES) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) (CAPACITORS) 0.1 0.1 100P 100P 100P 100P 0.1 100P 1 10P 0.1 1 47 1 47 0.1 0.1 100P 47 0.1 0.1 100P 0.1 0.1 0.1 0.1 0.1 0.033 0.01 0.1 680P 0.1 0.1 0.1 100P 0.1 0.1 0.1 4.7 0.001 100P
2SB1322 PQVTDTC143E PQVTDTC143E PQVTDTC143E PQVTDTC143E B1DHDD000026 PQVTDTC143E B1ABDF000025 B1ABDF000025 B1ABDF000025 2SB1218ARL
S S S S S
GEAR, A
BAT1
BR2032/1HF1
COVER
S S S S S
INSTRUCTION BOOK HANDSET ASS'Y SHEET PAPER GIFT BOX CUSHION CUSHION CUSHION PACKING SHEET PROTECTION COVER PROTECTION COVER
C10 C12 C13 C14 C30 C31 C50 C51 C71 C72 C73 C74 C75 C76 C78 C79 C80 C81 C85 C87 C90 C92 C94 C102 C103 C104 C105 C112 C113 C114 C115 C116 C118 C125 C127 C128 C129 C140 C142 C143 C150
ECUE1A104KBQ ECUE1C104ZFQ ECUE1H101JCQ ECUE1H101JCQ ECUE1H101JCQ ECUE1H101JCQ ECUE1C104ZFQ ECUE1H101JCQ ECUV1A105ZFV EEE1CA101WP ECUE1C104ZFQ ECUV1A105ZFV F2G0J4700032 ECUV1A105ZFV F2G0J4700032 ECUE1C104ZFQ ECUE1C104ZFQ ECUE1H101JCQ F2G0J4700032 ECUE1C104ZFQ ECUE1C104ZFQ ECUE1H101JCQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1A333KBQ ECUE1C103KBQ ECUE1A104KBQ ECUE1H681KBQ ECUE1C104ZFQ ECUE1A104KBQ ECUE1A104KBQ ECUE1H101JCQ ECUE1A104KBQ ECUE1C104ZFQ ECUE1A104KBQ ECJ1VB0J475K ECUE1H102KBQ ECUE1H101JCQ
169
KX-FT932BR-B
Safety
Ref. No. C151 C153 C154 C155 C158 C159 C160 C161 C162 C163 C164 C165 C167 C168 C169 C171 C172 C173 C174 C175 C176 C177 C178 C179 C201 C202 C203 C204 C205 C206 C207 C216 C217 C219 C221 C222 C225 C226 C229 C232 C233 C234 C235 C236 C237 C238 C239 C240 C241
Part No. ECUE1C104ZFQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1H102KBQ ECUE1H222KBQ ECUE1A104KBQ ECUE1A104KBQ ECUE1H100DCQ ECUE1H100DCQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1H102KBQ ECUE1H102KBQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1H100DCQ ECUE1H100DCQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1C104ZFQ ECUE1E472KBQ ECUE1C104ZFQ ECUV1A105ZFV ECUE1H330JCQ ECUV1A105ZFV ECUE1C104ZFQ ECUE1H102KBQ ECJ0EB0J224K ECUE1A104KBQ ECUE1A104KBQ ECJ0EB0J224K ECUE1A104KBQ ECUV1C683KBV ECUE1C104ZFQ ECUE1C104ZFQ ECUE1H101JCQ ECUE1C104ZFQ ECUE1C104ZFQ F2G1C1000014 ECUV1H100JCV ECUV1H100JCV ECUV1A105ZFV ECUE1C104ZFQ ECUE1C104ZFQ ECUE1C104ZFQ
Part Name & Description Remarks 0.1 0.1 0.1 0.1 0.1 0.001 0.0022 0.1 0.1 10P 10P 0.1 0.1 0.001 0.001 0.1 0.1 10P 10P 0.1 0.1 0.1 0.1 0.1 0.0047 0.1 1 33P 1 0.1 0.001 0.22 0.1 0.1 0.22 0.1 0.068 0.1 0.1 100P 0.1 0.1 10P 10P 10P 1 0.1 0.1 0.1 (CONNECTORS) CONNECTOR, 9 PIN CONNECTOR, 16 PIN CONNECTOR, 5 PIN CONNECTOR, 11 PIN CONNECTOR, 2 PIN CONNECTOR, 10 PIN CONNECTOR, 7 PIN CONNECTOR, 2 PIN
Safety
F1 F2
(FUSES) K5H122200005 FUSE K5H251200003 FUSE (RESISTORS) 0 10K 0 0 820 1.5K 220 5.6K
Ref. No. R 11 R 12 R 13 R 34 R 36 R 38 R 40 R 57 R 59 R 70 R 71 R 72 R 73 R 74 R 75 R 76 R 78 R 79 R 80 R 90 R 93 R 94 R 95 R 96 R 102 R 123 R 124 R 126 R 127 R 128 R 130 R 131 R 140 R 141 R 142 R 150 R 151 R 152 R 153 R 154 R 155 R 158 R 159 R 161 R 162 R 163 R 164 R 172 R 178 R 200 R 214 R 219 R 221 R 223 R 226 R 227 R 228 R 229 R 231 R 232 R 233
Part No. ERJ2GEJ222 ERJ2GEJ472X ERJ2GEJ101 ERJ2GEJ472X ERJ2GEJ472X ERJ2GEJ472X ERJ2GEJ222 ERJ2GEJ473 ERJ2GEJ472X ERJ3GEY0R00 ERJ2GEJ333 ERJ3EKF1101 ERJ3EKF3602 ERJ2GEJ104 ERJ2GEJ123 ERJ2GEJ822 ERJ2GEJ334 ERJ2GEJ475 ERJ2GEJ222 ERJ2GEJ332 ERJ2GEJ222 ERJ2GEJ223 ERJ2GEJ152 ERJ2GEJ100 ERJ2GEJ103 ERJ2GEJ564 ERJ2GEJ473 ERJ2GEJ393X ERJ2GEJ334 ERJ2GEJ363 ERJ2GEJ243 ERJ2GEJ332 ERJ2GEJ153 ERJ2GEJ912 ERJ2GEJ103 ERJ2GEJ222 ERJ2GEJ472X ERJ2GEJ223 ERJ2GEJ100 ERJ2GEJ473 ERJ2GEJ223 ERJ2GEJ471 ERJ2GEJ124 ERJ2GEJ332 ERJ2GEJ105X ERJ2GEJ151 ERJ2GEJ102 ERG2SJ681 ERJ2GEJ102 ERJ2GE0R00 ERJ2GEJ272 ERJ2GEJ103 ERJ2GEJ472X ERJ2GEJ392 ERJ2GEJ203 PQ4R18XJ220 ERJ2GEJ473 ERJ2GEJ102 ERJ2GE0R00 ERJ2GEJ472X ERJ2GEJ332
Part Name & Description Remarks 2.2K 4.7K 100 4.7K 4.7K 4.7K 2.2K 47K 4.7K 0 33K 1.1k 36k 100K 12K 8.2K 330K 4.7M 2.2K 3.3K 2.2K 22K 1.5K 10 10K 560K 47K 39K 330K 36K 24K 3.3K 15K 9.1K 10K 2.2K 4.7K 22K 10 47K 22K 470 120K 3.3K 1M 150 1K 680 1K 0 2.7K 10K 4.7K 3.9K 20K 22 47K 1K 0 4.7K 3.3K (COMPONENTS PARTS) COMPONENTS PARTS COMPONENTS PARTS COMPONENTS PARTS COMPONENTS PARTS COMPONENTS PARTS COMPONENTS PARTS COMPONENTS PARTS COMPONENTS PARTS COMPONENTS PARTS SOLID RESISTOR
L2 L6 L7 L21 R 1 R 2 R 3 R 10
RA101 RA102 RA103 RA106 RA107 RA108 RA109 RA110 RA111 RA112
EXB28VR000X EXB28V101JX EXB28V103 EXB28V101JX EXB24V221JX EXB24V332JX EXB24V103JX EXB24V472JX EXB24V472JX EXB24V101JX
170
KX-FT932BR-B
Safety
Part No.
Safety
EXB24V124JX COMPONENTS PARTS F5A421040004 COMPONENTS PARTS F5A421040004 COMPONENTS PARTS (CRYSTAL OSCILLATORS) H0A327200147 CRYSTAL OSCILLATOR H2A240500005 CRYSTAL OSCILLATOR H0J322500006 CRYSTAL OSCILLATOR
Part No.
PQVDDSS301L VARISTOR PFRZRA102P6T VARISTOR (RESISTORS) 0 0 0 0 100 10K 10K 10K 120K 120K 56K 15K 120K 56K 110K 56K 220K 220K 39K 12K 560K 10K 270 12K 10K 18K 51K 27K 2.2K 15K 330K 150 560K 330 220K 47K 18K 0 6.2K 12K 12K 47K 22 1.5K 1.5K 330 10K 1M 22 12 (CAPACITORS) 4.7 47 0.1 270P 270P 47 0.027 0.1 10P 0.0015 10P 0.082 0.015 0.1 0.082 10P
X1 X2 X3
ERJ3GEY0R00 ERJ3GEY0R00 ERJ3GEY0R00 ERJ6GEYJ1R0 ERJ3GEYJ101 ERJ3GEYJ103 ERJ3GEYJ103 ERJ3GEYJ103 ERJ3GEYJ124 ERJ3GEYJ124 ERJ3GEYJ563 ERJ3GEYJ153 ERJ3GEYJ124 ERJ3GEYJ563 ERJ3GEYJ114 ERJ3GEYJ563 ERJ3GEYJ224 ERJ3GEYJ224 ERJ3GEYJ393 ERJ3GEYJ123 ERJ3GEYJ564 ERJ3GEYJ103 ERDS2TJ271 ERJ3GEYJ123 ERJ3GEYJ103 ERJ3GEYJ183 ERJ3GEYJ513 ERJ3GEYJ273 ERJ3GEYJ222 ERDS1TJ153 ERJ3GEYJ334 ERG2SJ151 ERJ3GEYJ564 ERJ3GEYJ331 ERJ3GEYJ224 ERDS1TJ473 ERJ3GEYJ183 ERJ3GEY0R00 ERJ3GEYJ622 ERJ3GEYJ123 ERJ3GEYJ123 ERJ3GEYJ473 ERJ3GEYJ220 ERJ3GEYJ152 ERJ3GEYJ152 ERJ3GEYJ331 ERJ3GEYJ103 ERJ3GEYJ105 ERJ3GEYJ220 ERJ8GEYJ120
IC1 IC2
(ICs) C0ABEB000083 IC C0ABEB000083 IC (TRANSISTORS) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI)
Q1 Q2 Q3 Q6 Q7 Q8
D1 D2 D3 D8 DA3
(DIODES) MA4047 DIODE(SI) MA4056 DIODE(SI) MA4056 DIODE(SI) B0EAAD000001 DIODE(SI) B0ADEJ000026 DIODE(SI) (JACKS AND CONNECTOR) PQJS16A10Z CONNECTOR, 16 PIN K2LA1YYB0001 JACK K2LB1YYB0002 JACK K2LB1YYB0002 JACK (SWITCHES) PFSH1A03Z PUSH SWITCH K0L1KA000007 PUSH SWITCH PFSH1A03Z PUSH SWITCH (COILS) COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL (PHOTO DUCER) PHOTO DUCER ELECTRIC ELECTRIC TRANSTRANS-
S S S
S S
PQLQR2KA113 PQLQR2KA113 PQLQR2KA113 PQLQR2KA113 PQLQR2KA113 PQLQR2KA113 PQLQR2KA113 PQLQR2KA113 PQLQR2KA20T PQLQR2KA20T PQLQR2KA20T
S S S S S S S S S S S
PC1
0N3181
POS1
PFRT001
(THERMISTOR) THERMISTOR
RLY1
T1
C4 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C17 C19 C20 C21 C22
ECEA1HKA4R7 ECEA0JKA470 ECUV1E104ZFV ECUV1H271KBV ECUV1H271KBV ECEA0JKA470 ECUV1H273KBV ECUV1C104KBV ECUV1H100DCV ECUV1H152KBV F2A1C1000030 ECUV1C823KBV ECUV1C153KBV ECUV1E104ZFV ECUV1C823KBV ECUV1H100DCV
S S
171
KX-FT932BR-B
Safety
Ref. No. C23 C24 C25 C28 C29 C30 C31 C32 C33 C34 C36 C38 C39 C40 C41 C45 C46 C47 C48 C49 C50 C51 C63 C72
Part No. ECUV1H220JCV PQCUV1H104ZF ECUV1C223KBV ECEA1HKA4R7 ECUV1H103KBV ECUV1C104KBV ECUV1E104ZFV ECUV1H151JCV ECUV1C104KBV ECUV1H221KBV ECUV1H100DCV F0C2E105A216 ECUV1H472KBV ECUV1C273KBV ECUV1C273KBV F2A1C1000030 ECUV1H103KBV ECEA0JKA470 ECUV1H103KBV ECUV1H103KBV ECUV1C683KBV ECUV1C104KBV F1H1H333A748 PQCUV1H104ZF
Part Name & Description Remarks 22P 0.1 0.022 4.7 0.01 0.1 0.1 150P 0.1 220P 10P 1 0.0047 0.027 0.027 10P 0.01 47 0.01 0.01 0.068 0.1 CERAMIC CAPACITOR 0.1
Safety
Ref. No. SW30 SW31 SW32 SW33 SW34 SW35 SW38 SW39
Part No. K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0L1BA000095 K0L1AA000002
Part Name & Description Remarks SPECIAL SPECIAL SPECIAL SPECIAL SPECIAL SPECIAL SWITCH, SWITCH, SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SENSOR SENSOR S S S S S S
R R R R R R R R R R R R R R R R R
1 2 3 4 5 14 15 17 18 19 20 21 22 23 24 25 50
ERJ3GEY0R00 ERJ3GEY0R00 ERJ3GEY0R00 ERJ3GEY0R00 ERJ3GEY0R00 ERJ3GEY0R00 ERJ3GEYJ183 ERJ3GEYJ222 ERJ3GEYJ271 ERJ3GEYJ4R7 ERJ3GEYJ101 ERJ3GEYJ101 ERJ3GEYJ472 ERJ3GEYJ472 ERJ3GEYJ102 ERJ3GEYJ821 ERJ3GEYJ330
(RESISTORS) 0 0 0 0 0 0 18K 2.2K 270 4.7 100 100 4.7K 4.7K 1K 820 33 (CAPACITORS) 0.1 220 330P 0.01 330P 120P 0.1 0.1 0.22 0.01 0.01
IC1
LED1
LNJ801LPDJA
CN1
(CONNECTOR) K1KA10B00215 CONNECTOR, 10 PIN (LIQUID CRYSTAL DISPLAY) L5DAAFB00001 LIQUID CRYSTAL DISPLAY (SWITCHES) SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH SPECIAL SWITCH
ECJ1VF1E104Z ECEA0JKA221 ECJ1VB1H331K ECJ1VB1H103K ECJ1VB1H331K ECJ1VC1H121J ECJ1VF1E104Z ECJ1VF1E104Z ECJ1VF1C224Z ECJ1VB1H103K ECJ1VB1H103K
CN2
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 SW11 SW12 SW13 SW14 SW15 SW16 SW17 SW18 SW19 SW20 SW21 SW22 SW23 SW24 SW25 SW26 SW27 SW28
K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259 K0H1BA000259
N0AB2GJ00005 POWER SUPPLY BOARD ASS'Y (RTL) (TRANSISTOR) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) TRANSISTOR(SI) (DIODES) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI) DIODE(SI)
D4 D5 D7 D9 D10 D11 D12 D13 D17 D20 D22 D23 D27 D101 D104 D105
1SS355F PFVDHZS9 1SS355F 1SS355F PSVDERA1506 PSVDERA1506 PSVDERA1506 PSVDERA1506 1SS355F PFVDERA9102 1SS355F 1SS355F MA8091 PFVDYG911S2R PFVDEC31QS04 PFVDTZPT8130
S S S S S
S S S
172
KX-FT932BR-B
Safety
Part Name & Description Remarks DIODE(SI) (CONNECTORS) CONNECTOR, 9 PIN (COIL) COIL COIL (FUSE) FUSE (PHOTO ELECTRIC TRANSDUCER) PHOTO ELECTRIC TRANSDUCER (TRANSFORMER) TRANSFORMER S
Safety
Part No.
CNJ2
PFJPB9BPHKL
BEA1 L1
PSLEBL02RN1 OR7A103F20
F1
PFBA51MS40L
PC1
PS2581AL1
T1
PFLT54D1
VR101 ZNR1
(VARISTOR) ECNCYAA03B53 VARIABLE RESISTOR ECN471D07A VARISTOR (RESISTORS) 0 0 0 180K 180K 100K 20K 270 560 33K 6.8K 8.2K 20K 620 100K 10 0 0 100K 0 33K 8.2K 6.8K 47K 1M 1M 1M 270 1K 7.5K 20K 10K 18K 22K (CAPACITORS) 0.33 180 0.0033 220P 0.0047 0.01 0.001 2.2 100P 1 0.22 330 470
S S
Note: Tools and Extension Cords are useful for servicing. (They make servicing easy.)
ERJ6GEY0R00 ERJ6GEY0R00 ERJ6GEY0R00 RK73H2A1803F RK73H2A1803F RK73H2A1003F PQ4R10XJ203 PQ4R18XJ271 PQ4R10XJ561 ERJ3GEYJ333 ERJ3GEYJ682 PQ4R10XJ822 ERJ3GEYJ203 ERJ3GEYJ621 RK73B1J104J ERDS2TJ100 ERJ3GEY0R00 ERJ3GEY0R00 RK73B1J104J ERJ6GEY0R00 ERJ3GEYJ333 ERJ3GEYJ822 ERJ3GEYJ682 ERJ3GEYJ473 RK73B2B105J RK73B2B105J RK73B2B105J PQ4R10XJ271 ERJ3GEYJ102 ERJ3GEYJ752 ERJ3GEYJ203 ERJ3GEYJ103 PQ4R18XJ183 PQ4R18XJ223
S S S
S S
PFCKDLE334M PFCKDVB180M DE2E3KH332 DEHR33A221 PFCKDB11H472 PFCKD8BH103 PFCKDB11H102 PFCKD31E225 PFCKD2C1H101 PFCKD31E105 PFCKD71H224 PFCEA35L330M PFCEA16ZL470
S S
S S S S S S S S S
Y.M KXFT932BRB
173