Documente Academic
Documente Profesional
Documente Cultură
INSTALLATION MANUAL
Table of Contents
Chapter 1
Chapter 2
Chapter 3
Introduction 1.1 System Specification Recommendation 1.2 Important Notes Hardware 2.1 DVR Line-up 2.2 Sentry 1104 2.3 Sentry 1516 2.4 Sentry 2004 2.5 Sentry 2016 2.6 Sentry 3016 2.7 Sentry 3032 2.8 Sentry 5016 2.9 Sentry 5216 2.10 Sentry 5416 2.11 Sentry 6432 2.12 Audio Board (1ch) 2.13 Audio Board (2ch) 2.14 Audio Board (4ch) 2.15 Audio Board (8ch) 2.16 I/O Card 2.17 Pan/Tilt Connection to DVR 2.18 4-Ch BNC Guide Connection to DVR Board 2.19 AV-Connection With Multi Boards Software 3.1 Device Driver Installation 3.2 DVR Software Installation 3.3 Folders Created After DVR Program Install 3.4 DVR Program Image Files 3.5 Language Alternation
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
6 6 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 28 29 32 32 33
CHAPTER 1. INTRODUCTION
The below is the recommended computer specification to work with DVR board.
Sentry 1004 2016 Cel 1.8GHz grade or above Intel Chipset Win 2000/XP/Vista/7 128 Mbyte or above Intel onboard VGA / ATI 110/220V 300W Version 9.0
512 Mbyte or above Intel onboard VGA / ATI Radeon 4XXX Series
1) Hard Drive Partition - Set C: drive for Operating System only with size appx. 10Gbyte - Set another drives (D:,E:.) for recording data with size 200 300Gbyte
2) Display Setup - Set resolution at 1024x768 and High Color 16bit. - Set System Standby, Turn off monitor and Turn off hard disk at Never in Display Properties\Power Management Properties\Power Schemes.
3) Rebooting Setup We highly recommend you to set automatic daily rebooting in idle time for most stable system operation.
CHAPTER 2. HARDWARE
Model Sentry 1104 Sentry 1516 Sentry 2004 Sentry 2016 Sentry 3016 Sentry 3032 Sentry 5016 Sentry 5216 Sentry 5416 Sentry 6432
Video Input 4Ch 16Ch 4Ch 16Ch 16Ch 32Ch 16Ch 16Ch 16Ch 32Ch
Display / Recording NTSC : 30fps / 30fps , PAL : 25fps / 25fps NTSC : 60fps / 60fps , PAL : 50fps / 50fps NTSC : 120fps / 120fps , PAL : 100fps / 100fps NTSC : 120fps / 120fps , PAL : 100fps / 100fps NTSC : 240fps / 240fps , PAL : 200fps / 200fps NTSC : 240fps / 240fps , PAL : 200fps / 200fps NTSC : 480fps / 120fps , PAL : 400fps / 100fps NTSC : 480fps / 240fps , PAL : 400fps / 200fps NTSC : 480fps / 480fps , PAL : 400fps / 400fps NTSC : 960fps / 480fps , PAL : 800fps / 400fps
Audio Input 1Ch 2 Ch 4Ch (Option) 4Ch (Option) 8Ch (Option) 8Ch (Option) 16Ch 16Ch 16Ch 16Ch
10
TV Out Impedence Jumper Arrangment Impedence : match the impedence value of video signal to the analog TV monitor property. (Default) NC : no impedence matching from capture card.
11
DI/DO Terminal
Pin No.1 Ground Pin No.1 Signal Pin No.2 Ground Pin No.2 Signal Pin No.3 Ground Pin No.3 Signal Pin No.4 Ground Pin No.4 Signal
12
DI/DO Terminal
TV Out Impedence Jumper Arrangment Impedence : match the impedence value of video signal to the analog TV monitor property. (Default) NC : no impedence matching from capture card.
13
DI/DO Terminal
16-Ch BNC Cable TV Out Impedence Jumper Arrangment TV Out Impedence : match the impedence value of video signal to the analog TV monitor property. (Default) NC : no impedence matching from capture card.
14
DI/DO Terminal
TV Out TV Out Impedence Jumper Arrangment Impedence : match the impedence value of video signal to the analog TV monitor property. (Default) NC : no impedence matching from capture card.
15
To AV In of 2016 #2
DI/DO Terminal
DI/DO Terminal
< 2016 Board #2> TV Out Impedence Jumper Arrangment 16-Ch BNC Cable Ch 5-8,13-16,21-24,29-32 Impedence : match the impedence value of video signal to the analog TV monitor property. (Default) NC : no impedence matching from capture card.
16
Parts Included : one 5016 board + one BNC Cable for Video + one RCA Cable for Audio
DI/DO Interminal
TV-Out (RCA)
17
2.9 Sentry 5216
Parts Included : one 5216 board + one BNC Cable for Video + one RCA Cable for Audio
DI/DO Interminal
TV-Out (RCA)
18
Parts Included : one 5416 board + one BNC Cable for Video + one RCA Cable for Audio
DI/DO Interminal
TV-Out (RCA)
19
Parts Included : one 6432 board + two BNC Cable for Video + one RCA Cable for Audio + one video connection sub-board + two flat cable
* TV-Out Option ; 1 TV Monitor : Video Ch1~32 through TV-Out Port#1 2 TV Monitor : Video Ch1~16 through TV-Out Port#1 , Video Ch17~32 through TV-Out Port#2 Single channel or four channel in quad mode selectable.
20
MIC In
PCI Slot
21
< 1516 Board > Audio In 1-2 Not Used < Audio Extension Board >
PCI Slot
22
60 Pin Connection
Audio In 1-4
PCI Slot
23
3016 Board
PCI Slot
24
Alarm Output
25
[ Sensor Input ] 1. Connection Connect one signal line to COM port and connect another signal line to the desired sensor number. 2. Operation - Normal : 1-4 Terminal & COM Port Open - Sensor Detection : 1-4 Terminal & COM Port Close 3. At normal close mode, it works reversely. 1. Connection Connect both power lines to DO terminal 2. Operation - Normal : DO Terminal Open - Control Output : DO Terminal Close 3 D/O Voltage .DC 30V, 1A or below .DC 110V, 0.3A or below .AC 125V, 500mA or below [ Alarm Output ]
Notes ; - N/O : Normal Open - N/C : Normal Close - DI Operation Mode (N/O or N/C) can be selected from Setup Mode of DVR Program - D/O Delay Time can be adjusted from Setup Mode of DVR Program
In order to control PTZ function from DVR, connect the convertor which can convert RS232C to RS422/485 singal to COM port of DVR. Then connect signal line from receiver to convertor. Select the correct protocol type from Sentry DVR program and match the address number of each PTZ camera to each one in PTZ setup in Sentry DVR Program.
RS422/485 Converter
26
27
Red Orange
Yellow Green
Blue Violet
Detail of A
Pin No.
1 0
1 1
1 2
1 3
1 4
1 5
1 6
17
Signal Ground
Line Color Matching to Each Pin on Terminal Pin No. Signal GND Pin No. Signal GND Black Brown Red Orange Yellow Green Blue Violet Black Brown Red Orange Yellow Green Blue Violet Black Brown Pin 9 Red Orange Pin 10 Yellow Green Pin 11 Blue Violet Pin 12 Black Brown Pin 13 Red Orange Pin 14 Yellow Green Pin 15 Blue Violet Pin 16 Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8
In case of using over two pcs of 4-Ch BNC Guides, you can connect to Pin 5 ~ Pin 16.
28
When you connect TV line to 2 to 4pcs of 1004/1104 boards, 2pcs of 1516 board or 2 pcs of 2016 board, the jump cable connection between boards are as below.
29
CHAPTER 3. SOFTWARE
30
1. Run DVRDriverSetup.exe from Driver-2010-XX-XX folder in the software CD provided. 2. Select Install DVR Device Driver and press OK.
3. After driver installation completes, reboot the system. 4. When device driver is installed successfully, device driver is diaplayed in Device Manager as below. - 1104 : 1 DVR Video Device + 1 DVR Audio Device Under DVR System - 1516 : 2 DVR Video Device + 2 DVR Audio Device Under DVR System - 2004/2016 : 4 DVR Video Device + 2 DVR Audio Device Under DVR System - 3016/3032 : 8 DVR Video Device + 8 DVR Audio Device Under DVR System - 5016/5216/5416/64432 : 1 DVR Video Device Under DVR System
31
1. Run Setup.exe from HDServer-2010-XX-XX folder in the software CD provided. 2. Destination folder selection will be displayed. Press Next.
32
5. After installation completes, press Finish. Then the system will reboot.
6. After the system reboots, HD DVR software will start automatically (if HDDVSS4 is added in Startup
33
Menu successfully).
8. Select the drive and Recording Type (Record : for recording data or Backup : for recorded data back-up) other than C: drive. Press Apply. You can repeat the procedure to set multiple recording drives. Then press OK.
34
35
Folder Name Language LogFile PanTilt Skin Sound Tools Update WebPages
Description Language files exist System Log files exist PTZ Driver files exist GUI skin file exists Sound files (*.wav) used in DVR program exist Utilities exist (Backup, Backup Player & CaptureClear) Temp folder for download when real-time update Web files for web service exists
There are a few image files used in DVR Program. The files can be replaced with the ones that the users desire to have. File Name Logo.bmp MiniLogo.bmp Splash.bmp DVSS4WallPaper.b mp Playbacklogo.bmp Disconnect.bmp Note Shown on blank channel where no camera input exists from playback GUI Shown when no video signal 320 X 240 BMP 320 X 240 BMP Description Shown on blank channel where no camera input exists from main GUI Shown on main GUI to display 98 X 50 500 X 200 1024 X 768 BMP BMP BMP suppliers logo Shown when loading DVR Program Wallpaper when used on DVR mode Size 320 X 240 Forma t BMP C:/DVSS4/Imag e C:/DVSS4/Imag e C:/DVSS4/Imag e C:/DVSS4/Imag e C:/DVSS4/Imag e C:/DVSS4/Imag e - You can make image files and copy them to image folder. - In order to apply customized images from install stage, you can make image folder in installation folder (ex ; Server-2003XXXX) and copy the image files to the folder. Path
36
You can customize the language used in Sentry DVR Program Setup by editing language file in CDVSS4\Language folder. Normally the initial language is English after the installation.
Procedure 1. Go to CDVSS4\Language. 2. Open Lang.ENU.ini. 3. Its content is ; [SYSTEM] MainColor = 166 184 206 (Basic Color) TextColor = 0 0 0 (Font Color) EditColor = 0 0 0 EditTextColor = 0 255 0 FontName = Verdana (Font Name) FontSize=14 (Font Size) FontStyle = 700 (Font Type Bold:700, Normal:400) [MESSAGE] Language change starts below this line. Input the term with your language on the right to = mark cancel = cancel yes = yes Ex ) yes = si (when changing from English to Italian) [MENU] [RECORD] 4. Close the language file after changes done. Rename it to the one suitable (Lang_XXX.ini) for your system language. Language Script Code
37
Afrikaans Albanian Arabic Latin 1 Latin 1 Arabic AFK SQI ARA (Saudi Arabia) ARB (Lebanon) ARI (Iraq) ARE (Egypt) ARG (Algeria) ARJ (Jordan) ARK (U.A.E.) ARL (Libya) ARM (Monaco) ARO (Oman) ARQ (Qatar) ARS (Syria) ART (Tunisia) ARU (Bahrain) ARY (Yemen) Armenian Azeri (Cyrillic) Azeri (Latin) Basque Belarusian Bulgarian Catalan Chinese (PRC) Chinese (Taiwan) Chinese SAR, PRC) Chinese (Singapore) Chinese (Macao SAR) Han (ideographic) Han (ideographic) ZHI ZHM (Hong Armenian Cyrillic Ext. Latin (code page 1254) Latin 1 Cyrillic Cyrillic Latin 1 Han (ideographic) Han (ideographic) Kong Han (ideographic) HYE AZE AZE EUQ BEL BGR CAT CHS CHT ZHH
38
Croatian Czech Danish Dutch Latin 2 Latin 2 Latin 1 Latin 1 HRV CSY DAN NLB (Belgium) NLD (Netherlands) English Latin 1 ENA (Australia) ENB (Belize) ENC (Canada) ENG (U.K.) ENI (Ireland) ENJ (Jamaica) ENL (Belize) ENP (Philippines) ENS (South Africa) ENT (Trinidad) ENU (U.S.) ENW (Zimbabwe) ENZ (New Zealand) Estonian Faeroese Farsi Finnish French Ext. Latin (code page 1257) Latin 1 Extended Arabic Latin 1 Latin 1 ETI FOS FAR FIN FRA (France) FRB (Belgium) FRC (Canada) FRL (Luxembourg) FRM (Monaco) FRS (Switzerland) Galician Georgian German Latin 1 Georgian Latin 1 GLC KAT DEA (Austria)
39
DEU (Germany) Greek Gujarati Hebrew Hindi Hungarian Icelandic Indonesian Italian Greek Gujarati Hebrew Devanagari Latin 2 Latin 1 Latin 1 Latin 1 ELL GUJ HEB HIN HUN ISL IND ITA (Italy) ITS (Switzerland) Japanese Kannada Kazakh Konkani Korean Kyrgyz Latvian Lithuanian FYRO Macedonian Malay Hirigana, Katakana, Kanji (ideographic) Kannada Cyrillic Devanagari Hangul and Hanja Cyrillic Ext. Latin (code page 1257) Ext. Latin (code page 1257) Cyrillic Latin 1 JPN KAN KKZ KNK KOR KYR LVI LTH MKI MSB (Brunei Darussalam) MSL (Malaysia) Marathi Mongolian Norwegian Devanagari Cyrillic Latin 1 MAR MON NON (Nynorsk) NOR (Bokmal) Polish Portuguese Latin 2 Latin 1 PLK PTB (Brazil)
40
PTG (Portugal) Punjabi Romanian Russian Sanskrit Serbian (Cyrillic) Serbian (Latin) Slovak Slovenian Spanish Gurmukhi Latin 2 Cyrillic Devanagari Cyrillic Latin 2 Latin 2 Latin 2 Latin 1 PAN ROM RUS SAN SRB SRL SKY SLV ESA (Panama) ESB (Bolivia) ESC (Costa Rica) ESD (Dom. Rep.) ESE (El Salvador) ESF (Ecuador) ESG (Guatemala) ESH (Honduras) ESI (Nicaragua) ESL (Chile) ESM (Mexico) ESN (Spain, intl. sort) ESO (Colombia) ESP (Spain, trad. sort) ESR (Peru) ESS (Argentina) ESU (Puerto Rico) ESV (Venezuela) ESY (Uruguay) ESZ (Paraguay) Swahili Swedish Latin 1 Latin 1 SWK SVE (Sweden) SVF (Finland)
41
Syriac Tamil Tatar Telugu Thai Turkish Ukrainian Urdu Uzbek (Cyrillic) Uzbek (Latin) Vietnamese Syriac Tamil Cyrillic Telugu Thai Ext. Latin (code page 1254) Cyrillic Extended Arabic Cyrillic Ext. Latin (code page 1254) Ext. Latin (code page 1258) SYR TAM TTT TEL THA TRK UKR URD UZB UZB VIT
Note ; In order to apply customized language from install stage, you can make language folder in installation folder (ex ; Server-2003XXXX) and copy the corresponding language file to the folder.