Documente Academic
Documente Profesional
Documente Cultură
DOCUMENT CODE
PLAN/PRJ/SUB UNIT PHASE DISCIPLANE DOCUMENT TYPE SERIAL NO. REV. NO. NO. OF PAGES: 4 DATE
NIOEC
000
EG
GN
SP
9078
A0
JULY, 2005
THIS SPECIFICATION IS THE PROPERTY OF NATIONAL IRANIAN OIL ENGINEERING & CONSTRUCTION COMPANY. IT IS CONFIDENTIAL AND ALL RIGHTS RESERVED TO THE OWNER. NEITHER WHOLE NOR ANY PART OF THIS DOCUMENT MAY BE DISCLOSED TO ANY THIRD PARTY, REPRODUCTED, STORED IN ANY RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY ANY MEANS WITHOUT THE PRIOR WRITTEN CONSENT OF THE NATIONAL IRANIAN OIL ENGINEERING & CONSTRUCTION COMPANY
JULY, 2005
NIOEC-SP-90-78(0)
JULY, 2005
NIOEC-SP-90-78(0)
REV. PAGE
REVISION INDEX
REV. PAGE
REV. PAGE
REV. PAGE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
NOTES:
1) 2) 3) 4) THIS SHEET IS A RECORD OF ALL REVISIONS TO THIS SPECIFICATION. REMARKS RELATED TO EACH REVISION SHOW A BRIEF DESCRIPTION. THESE REMARKS SHALL BE INTERPRETED IN CONJUNCTION WITH THE REVISED TEXT MARKED BY REVISION NUMBERS. WHEN APPROVED EACH REVISION SHALL BE CONSIDERED AS A PART OF THE ORIGINAL DOCUMENT. NUMBER OF PAGES EXCLUDES THIS SHEET AND THE COVER SHEET.
REV.
DATE
PREPARED
CHECKED
APPROVED
AUTHORIZED
JULY, 2005
CONTENTS:
0. 1.
INTRODUCTION ......................................................................................................................2 SCOPE.........................................................................................................................................2 1.1 Conflicting Requirements ..................................................................................................2 2. REFERENCES ...........................................................................................................................2 2.1. Equivalent to IPS Standard...............................................................................................3 3. UNITS ..........................................................................................................................................3 4. DEFINITION & THERMINOLOGY ......................................................................................4
JULY, 2005
NIOEC-SP-90-78(0)
0. INTRODUCTION To satisfy the requirements of this NIOEC Specification, Iranian Petroleum Standard IPS-MGN-350 with the modifications as specified herein after shall be strictly followed. Articles 0 through 4 of this document replace entirely the related articles in the referenced IPS Standard. 1. SCOPE -This NIOEC Specification covers general requirements including design, construction, inspection, testing and other aspects of Gantry and Overhead Cranes top running bridge and top running trolleys. -This Specification shall be applicable for purchasing and furnishing of Overhead and Gantry Cranes. -This Specification covers general requirements for overhead and gantry cranes with a top running bridge of single or multiple girder construction utilizing a top running trolley, including polar, semi gantry and cantilever gantry for use in refinery/ oil plant, distribution depots, pump stations and pipelines. -This Specification shall be used in conjunction with individual crane data sheet. -Compliance by the crane manufacturer with the provisions of this Specification does not relieve him of responsibility of furnishing crane and accessories of proper design, mechanically suited to meet guarantees at specified service conditions. -No deviations or exceptions from this Specification shall be permitted without the written prior approval of Employer. -Intended deviations shall be separately listed by the Vendor and supported by reasons thereof for Purchaser consideration. 1.1 Conflicting Requirements In the case of conflict between documents relating to the inquiry or order, the following priority of documents shall apply: - First priority Purchase order and variations thereto. - Second priority Data sheets and drawings. - Third priority This Specification. All conflicting requirements shall be referred to the Purchaser in writing. The Purchaser will issue confirmation document if needed for clarification. 2. REFERENCES Throughout this Specification the following dated and undated standards/ codes are referred to. These referenced documents shall, to the extent specified herein, form a part of this Specification.
JULY, 2005
NIOEC-SP-90-78(0)
For undated references, the latest edition of the referenced document (including any supplements and amendments) applies. For dated references, the edition cited applies. The applicability of changes in dated references that occur after the cited date shall mutually be agreed upon by NIOEC and the Vendor/Contractor. AISC (AMERICAN INSTITUTE OF STEEL CONSTRUCTION) "Manual of Steel Construction" AISE (ASSOCIATION OF IRON AND STEEL ENGINEERS) No. 6 "Specification for Electric Overhead Traveling Cranes for Steel Mill Service"
ASME (AMERICAN SOCIETY OF MECHANICAL ENGINEERS) A 12.1 B 30.2 A 14.3 "Safety Requirements for Floor and Wall Openings, Railings, and Toe boards" "Overhead and Gantry Cranes" "Safety Code for Fixed Ladders"
AWS (AMERICAN WELDING SOCIETY) D 1.1 D 14.1 "Structural Welding Code" "Specification for Welding of Industrial and Mill Cranes and Other Material Handling Equipment" (CRANE MANUFACTURERS ASSOCIATION OF AMERICA) "Specification for Electric Overhead Traveling Cranes"
(IRANIAN PETROLEUM STANDARD) "Material Standard for Overhead and Portal Bridge (Gantry) Cranes"
IPS-M-GN-350
NIOEC-SP (NIOEC SPECIFICATIONS) NIOEC-SP-00-10 NIOEC Specification for Units 2.1. Equivalent to IPS Standard Substitute the following IPS Standards as referred to throughout IPS-M-GN-350 to relevant NIOEC's Specifications as follows: IPS Standard IPS-M-GN-350 Relevant NIOEC Specification NIOEC-SP-90-78
3. UNITS 3
JULY, 2005
NIOEC-SP-90-78(0)
International system of units (SI) shall be used in accordance with NIOEC-SP-00-10, unless otherwise specified. 4. DEFINITION & THERMINOLOGY For the purpose of this Specification definitions given in ASME Standard B 30.2 Section 2-0.2 shall hold.