Mits C005A (2011 2012) GeneralCataloge

USING THIS CATALOG
aThis
catalog was made in JANUARY 2011.
aStock
a Please
note that products in this catalog are

continuously reviewed and updated. The products
therefore may be changed in the future and thus
become different from this catalog.
aStock status is mentioned for the products in this catalog.
However, please note that the products here may be
replaced by new grades and products in the future.
status indication
: Inventory maintained.
u : Inventory maintained. (Available Spring 2011)
s : Inventory maintained in Japan.
d : Inventory maintained in Japan. (Available Spring 2011)
r : Non stock, produced to order only.
a
(Note) Please contact us regarding grades and order numbers

that are not mentioned in this catalog.
HOW TO USE THIS CATALOG

In this catalog our cutting tools are classied into three main
bHow to use the block page.
categories, turning tools, milling tools and drilling tools, which
The usage guide for the section page is shown on the left
are arranged according to types of machining respectively.
page of the inside title (not for all sections). Refer to this
This helps you to nd the most suitable products through
page to know how to read the product information and how
some references as follows. Please read the instructions to
the page is organized.
nd the best products for your purpose.
zTo nd the products through INDEX.
TURNING
Turning tools are classied by green coloring.
INSERT STANDARDS
INSERT GRADES
Milling tools are classied by blue coloring.
Left Page of the
Drilling tools are classied by red coloring.
Inside Title
For the others, refer to the index on the following title page. Classication
xTo nd the series of products from the contents of the coloring for
turning tools.
inside title.
Contents of each block are listed on the inside title.
cTo nd the product from the classication of each book
according to applications.
The classication page of each block provides the series
Right Page of
of products to be selected according to applications and
the Inside Title
purposes.
Classication
coloring for
vTo nd the product through the index of tool numbers
turning
on front pages.
inserts.
In case the tool number of the product or the name of parts
Inside
Title
for
Turning
Inserts
are known, refer to the index of tool numbers alphabetically
listed on front pages.
IDENTIFICATION .............................................................................................. A002
HOLE GEOMETRY ........................................................................................... A004
PRECISION BREAKER STANDARD ............................................................... A008
...................................................................................................... A013
CLASSIFICATION OF GRADES AND CHIP BREAKERS FOR TURNING ..... A014
BREAKER SYSTEMS FOR SMALL SIZE INSERTS ....................................... A026
PRECISION BREAKER SYSTEM (NEGATIVE INSERTS) .............................. A027
WIPER INSERT................................................................................................. A028
GRADES FOR TURNING ................................................................................. A030
TURNING APPLICATION RANGE ................................................................... A031
COATED CARBIDE (CVD) ............................................................................... A032
COATED CARBIDE (PVD) ............................................................................... A034
CERMET ........................................................................................................... A036
COATED CERMET ........................................................................................... A037
CEMENTED CARBIDE ..................................................................................... A038
MICRO-GRAIN CEMENTED CARBIDE ........................................................... A039
CLASSIFICATION............................................................................................. A040
STANDARD OF TURNING INSERTS
NEGATIVE INSERTS WITH HOLE
SCooTYPE ... SQUARE 90 .................... A117

SPooTYPE ... SQUARE 90 .................... A118
TCooTYPE ... TRIANGULAR 60 ............ A119
TEooTYPE ... TRIANGULAR 60 ............ A121
TPooTYPE ... TRIANGULAR 60 ............ A122
VBooTYPE ... RHOMBIC 35 .................. A125
VCooTYPE ... RHOMBIC 35 .................. A128
VDooTYPE ... RHOMBIC 35 .................. A130
VP ooTYPE ... RHOMBIC 35 .................. A131
WBooTYPE... TRIGON 80...................... A132
WCooTYPE... TRIGON 80...................... A133
WPooTYPE ... TRIGON 80...................... A135
XCooTYPE ... RHOMBIC 25 .................. A136
CNooTYPE... RHOMBIC 80 .................. A068

DNooTYPE... RHOMBIC 55 .................. A074
RNooTYPE... ROUND ............................. A079
SNooTYPE ... SQUARE 90 .................... A080
TNooTYPE ... TRIANGULAR 60 ............ A085
VNooTYPE ... RHOMBIC 35 .................. A092
WNooTYPE... TRIGON 80...................... A094
NEGATIVE INSERTS WITHOUT HOLE
KNooTYPE... PARALLELOGRAM 55 ... A098

POSITIVE INSERTS WITH HOLE
CCooTYPE... RHOMBIC 80 .................. A101

CPooTYPE ... RHOMBIC 80 .................. A107
DCooTYPE... RHOMBIC 55 .................. A109
DEooTYPE ... RHOMBIC 55 .................. A114
RCooTYPE... ROUND ............................. A115
RGooTYPE... ROUND ............................. A116
POSITIVE INSERTS WITHOUT HOLE
RTG TYPE ................................... A137

A001
aHow the Text and Index are organized

TURNING INSERTS [NEGATIVE]
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Cutting Conditions :
Stainless Steel
Non-Ferrous Metal
Finish
Cutting
FS
Order Number
(ISO) Number
Carbide
CNMG430.5FH
431FH
432FH
433FH
CNMG120402-FH
120404-FH
120408-FH
120412-FH
CNMG431FS
432FS
CNMG120404-FS
120408-FS
.016
.031
CNMG431FY
432FY
CNMG120404-FY
120408-FY
.016
.031
CNGG43V5FJ
430.2FJ
430.5FJ
431FJ
432FJ
CNGG43V5FJ-P
430.2FJ-P
430.5FJ-P
CNGG1204V5-FJ
120401-FJ
120402-FJ
120404-FJ
120408-FJ
CNGG1204V5-FJ-P
120401-FJ-P
120402-FJ-P
.002
s
s
CNGG431PK
432PK
CNGG120404-PK
120408-PK
.016
.031
.008
a a
a a
.016
a s
sa
.031
a s
sa
.047
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
Finish
Cutting
FJ
Finish
Cutting
FJ-P
.004
.008
.016
a s
.031
a a
.008
: Inventory maintained. s : Inventory maintained in Japan.

: Non stock, produced to order only.
<10 inserts in one case>
a
r
a s
a
.004
Finish
Cutting
A068
ss
.002
Finish
Cutting
PK
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
a a a
a a
.031
a a a
a a
.047
a a a
CNMG431SY
432SY
CNMG120404-SY
120408-SY
.016
.031
SH
Coated
Cermet Cermet
Finish
Cutting
FY
.016
Heat-resistant Alloy, Titanium Alloy
(inch)
FH
CNMG120404-SA
120408-SA
120412-SA
160608-SA
160612-SA
CNMG090304-SH
090308-SH
09T304-SH
09T308-SH
120404-SH
120408-SH
120412-SH
CNMG120404-SW
120408-SW
120412-SW
Light
Cutting
Cast Iron
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Shape
(ISO) Number
CNMG431SA
432SA
433SA
542SA
543SA
CNMG321SH
322SH
32.51SH
32.52SH
431SH
432SH
433SH
CNMG431SW
432SW
433SW
Steel
Coated
Coated
Cermet Cermet
Coated
Order Number
SA
Unstable Cutting
C006
009
E021
Light
Cutting
SW
(With Wiper)
C006
009
E021
E024
H006
008
.031
.047
a r
.016
.031
.016
s
s
a
a a s
sa
sa
.016
SY
sa
.047
.016
a a
sa
.031
a a
sa
.047
a a
MJ
C006
009
E021
E024
H006
008
CNMG431C
432C
433C
CNMG120404-C
120408-C
120412-C
CNMG431MJ
432MJ
433MJ
434MJ
CNMG120404-MJ
120408-MJ
120412-MJ
120416-MJ
.016
CNGG431MJ
432MJ
CNGG120404-MJ
120408-MJ
.016
a a
a s
.031
a a
a s
.016
.031
.047
sa
sa
C006
009
E021
E024
H006
008
.031
.047
.063
Large Index
Product Section
C006
009
E021
E024
H006
008
a a
Light
Cutting
Light
Cutting
WITH
HOLE
E024
H006
008
a a s
Light
Cutting
MJ
NEG
C006
009
E021
E024
H006
008
C006
009
E021
s
s
a a s
.031
.031
Carbide
Light
Cutting
E024
H006
008
C006
009
E021
E024
H006
008
*
*
*
Unstable Cutting
Non-Ferrous Metal
Shape
Applicable
Holder Page
P
M
K
N
S
General Cutting
Cast Iron
(inch)
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
General Cutting
Stable Cutting
Steel
Stainless Steel
Standard
Feed (inch/rev)
Feed (inch/rev)
Stable Cutting
Work
Material
Flat Top
Applicable
Holder Page
Cast Iron (<350MPa)
NEG
Feed (inch/rev)
P
M
K
N
S
Heavy Cutting
Semi-Heavy Cutting
Stainless Steel (<200HB)
TURNING INSERTS
FH
Thickness Corner Radius Chip Breaker

Please refer to page A002.
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
Size
Medium Cutting
Light Cutting
Carbon SteelAlloy Steel (Wiper)
Depth of Cut (inch)
Finish Cutting
Carbon SteelAlloy Steel
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
CNMG 4 3 0.5
INSERTS
WITH HOLE
CN TYPE
Mild Steel
Depth of Cut (inch)
TURNING INSERTS
80
CHIP CONTROL RANGE FOR WORK MATERIALS
a a
r a
a a
ss
ss
r a
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
Light
Cutting
*Please refer to page A028 before using the SW breaker (wiper insert).
CHIP BREAKER
A040
IDENTIFICATION
A002
A069
INFORMATION
Web CATALOG : http://www.mitsubishicarbide.net/mmus/en/
*Please refer to page PR9.
INDEX
TURNING INSERTS
A001
CBN & PCD TURNING INSERTS
B001
EXTERNAL TURNING TOOLS
C001
SMALL TOOLS
D001
BORING BARS
E001
GROOVING
F001
THREADING
G001
HSK-T TOOLS
H001
SOLID END MILLS
I001
MILLING TOOL INSERTS
J001
MILLING
K001
DRILLING
L001
SPARE PARTS
M001
TECHNICAL DATA
N001
GENERAL CATALOG
ROTATING TOOLS
INDEX
TURNING TOOLS
2011-2012
TURNING
TOOLS
CVD coated grades for cast iron turning
series
UC5100
UC5105/UC5115
^ A032
General purpose coated CBN grade for hardened steel
BC8020
^
B004
PR1
CVD coated grades for steel turning
series
UE6100
UE6105/UE6110/
UE6020/UE6035
^ A032
CBN Breaker Insert
BF/BM breaker
^ B013
Cermet grade for turning
NX3035
^ A036
Breaker for steel turning
MP breaker
^ A044
Grooving system
GY series
^ F004 F157
Special breakers for difficult-to-cut materials
FJ/FJ-P/MJ/MJ-P
GJ/MS breaker
Threading tools
MMT series
^ G010G021
Double clamp type holder for copying
PROFILE HOLDER
^ C038, C039
Small tools
SMALL TOOLS
^ D002D047
For multi-task machines HSK tools
HSK-T
^ H002 H022
^ A040 A047, A050A057
PR2
MILLING
TOOLS
SOLID END MILL
IMPACT MIRACLE end mill Series
^ I138 I177
IMPACT MIRACLE end mills

with multiple internal through coolant holes
CoolStar
^ I143, I146, I147, I151
I152, I174, I176, I177
End mill series for high efficiency machining

for aluminum alloys
ALIMASTER
^ I188 I191
PR3
2 flute IMPACT MIRACLE

wide ball nose end mill
VF2WB
^
I154
IMPACT MIRACLE
vibration control end mill
VFHVRB
^ I170 I172
MSTAR end mills
MSTAR
^ I050 I110
IMPACT MIRACLE
vibration control end mill series
VF4SVB
^ I169
2 flute CBN long neck

ball nose and radius end mills
CBN2XLB/
CBN2XLRB
Diamond coated end mills

for graphite
DF
^ I178 I184
^ I186, I187
PR4
MILLING
TOOLS
CUTTER
Multi-functional end mills
APX3000/
APX4000
^
K030 K049
AHX640W

^ K014 K016
Face milling cutters with screw-on type inserts
Screw-on insert, shoulder milling cutters
ASX445
ASX400
^ K008 K013
PR5
Face milling cutters for high efficiency

machining of cast irons
^ K022K027
Strong edge insert type cutters for cast iron
VOX400
^ K020, K021
End mills for deep shoulder milling
SPX
^ K070 K075
Milling cutters for aluminum alloys
Ultra high feed rate radius milling cutters
AXD4000/
AXD7000
^ K052 K061
AJX
^
K088 K098
End mills for titanium alloy milling
VFX6
^ K076, K077
Indexable ball nose end Mill for finishing

Indexable corner Radius end Mill for finishing
SRF/SUF
^ K115 K123
PR6
DRILLING
TOOLS
Small diameter indexable drill
STAW
^ L094L097
Solid carbide drill with

through coolant holes
MICRO-MWS
^ L040L049
PR7
Indexable type drills
TAW
^ L098 L119
Solid carbide drill
MWE/MWS
^ L004 L015
Solid carbide drills for deep hole drilling
WSTAR
SUPER LONG DRILL

^ L016 L025
Solid carbide drills

for machining of aluminum alloys
MNS
^ L074L081
Micro solid carbide gun drill

for machining of stainless steel
MICRO-MGS MMS
^ L058, L059
^ L060L065
Solid carbide drill for die &

mold machining
MHS
^ L082 L090

for machining of steel and cast iron
MQS
Coming soon
PR8
Web CATALOG
Web catalog benets

1. You can select the optimum tools by using the Product Search function.
Searches can also be specified by using cutting mode, workpiece and cutting conditions.
2. Ultra quick search function.
3. Thanks to an industry first image display using SVG software, information can easily be enlarged with
images in a high quality format.
Additionally, detailed tool dimensions can be seen for each different type of tool geometry.
4. Includes the CAD data of approximately 4000 items.
5. Up to date information.
6. Useful tools are provided in the Technical Information Section.
(Formulas and Workpiece Material Dictionary, etc.)
PR9
INDEX
INDEX FOR TOOL NUMBER
A ............... II
B ............... II
C ............... III
D ............... IV
E ............... V
F ............... V
G ............... V
H ............... V
I ............... VI
J ............... VI
K ................ VI
L ............... VI
M ............... VI
N ............... VIII
O ............... IX
P ............... IX
Q ............... IX
R ............... IX
S ............... IX
T ............... XI
U ............... XII
V ............... XII
W ............... XIII
X ............... XIII
Z ............... XIII
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
ASX400Roooo .......................ASX400 type face mill ................................ K022
ASX400Roooooo .................ASX400 type face mill (Metric type) ........... K025
AEMWooooooooR ..............Insert (For BAE type end mill) ............ J016,J017 ASX400RooooC/E/M .............ASX400 type face mill ................................ K022
AEMWoooooooR.................Insert (For BAE type end mill) ............ J016,J017 ASX400RoooAM16oo...........ASX400 type screw-in end mill
AHX640W-ooooooR/L .........AHX640W type face mill ............................. K015
(Metric type) ............................................ K025
AHX640WR/Looooo .............AHX640W type face mill ............................. K014 ASX400RoooS32....................ASX400 type end mill (Metric type) ............ K024
AHX640WR/Loooooo...........AHX640W type face mill (Metric type) ........ K016 ASX400RoooWoo .................ASX400 type end mill ................................. K023
AJSooooToo ........................Clamp screw (For AJX type cutter).............M003 ASX445-ooooooR ................ASX445 type face mill (Metric type) ........... K009
AJXoo-oooA/BooR..............AJX type face mill (Metric type) .................. K092 ASX445Roooooo .................ASX445 type face mill ................................ K010
AJXooRoooooo ..................AJX type face mill (Metric type) .................. K093 ASX445RooooC/E/M .............ASX445 type face mill ................................ K008
AJXooRoooAMoooo..........AJX type screw-in end mill (Metric type) .... K094 ASX445RooooSoo ...............ASX445 type end mill ................................. K010
AJXooRoooSAooS/L/EL .....AJX type end mill (Metric type) .......... K090,K091 AXD4000-oooAooRo ...........AXD4000 type face mill (Metric type) ......... K052
AJX14RAoooooE/F ..............AJX type cutter ........................................... K089 AXD4000RooooooA/B .........AXD4000 type face mill (Metric type) ......... K052
AJXUooRoooo .....................AJX type cutter ........................................... K089 AXD4000RoooSAoooo .......AXD4000 type end mill (Metric type) .......... K053
AJXUooRooooC/E ...............AJX type cutter ........................................... K089 AXD7000-oooA/BooRo ........AXD7000 type face mill (Metric type) ......... K057
AJXUooRoooFA/SA/WAooS/M/L...AJX type end mill ........................................ K088 AXD7000Rooooooo ............AXD7000 type face mill (Metric type) ......... K058
AMSo ........................................Clamp bridge (For AJX/BRE type cutter)....M014 AXD7000RoooooA-H63A .....AXD7000 type HSK shank end mill
AOGT1236ooPEFR-GM ..........Insert (For APX3000 type cutter) ........J012,K035
(Metric type) ............................................ K058
AOMT1236ooPEER-H/M.........Insert (For APX3000 type cutter) ........J013,K035 AXD7000RoooSAooSo ........AXD7000 type end mill (Metric type) .......... K057
AOMT1848ooPEER-H/M.........Insert (For APX4000 type cutter) ........J013,K043 AXD7000URoooooo.............AXD7000 type face mill .............................. K056
AOX445-063A04R/L .................AOX445 type face mill (Metric type) ........... K017 AXD7000URoooSAooSo .....AXD7000 type end mill ............................... K056
AOX445R/Loooooo ..............AOX445 type face mill (Metric type) ........... K017
AOX445R/LoooS32 ................AOX445 type end mill (Metric type) ............ K017
APGTooooPDFR-Go ............Insert (For BAP300/400 type cutter) ............. J017
K067,K068 BAP300RooooWLoo............BAP300 type end mill ................................. K068

APMTooooPDER-Ho ............Insert (For BAP300/400/SRM2 type cutter) ......... BAP300RoooWoo .................BAP300 type end mill ................................. K066
J017,K067,K068 BAP3500RoooooooLB/SA/SB ...BAP3500 type end mill ............................... K050
K129,K131,K134 BAP3500RooooA ..................BAP3500 type face mill .............................. K050
APMTooooPDER-Mo ............Insert (For BAP300/400/SRM2 type cutter) ......... BC5 ...........................................Clamp set (For F type boring bar) ..............M003
J017,J018,K067 BCP141 .....................................Shim pin......................................................M013
K068,K129,K131,K134 BF407RooooC/E/F/M.............BF407 type face mill ................................... K019
APMT1604PDER ......................Insert (For milling)........................................ J032 BF-CCGTooo-TA2 ..................Insert (Class G tolerance)........................... B039
APX3000-oooAooRA ............APX3000 type face mill (Metric type) ......... K033 BF-CNGGooo-TA4 .................Insert (Class G tolerance)........................... B022
APX3000RoooooCA/DA .......APX3000 type face mill (Metric type) ......... K033 BF-CNGMooo-TA2 .................Insert (Class G tolerance)........................... B023
APX3000RooooA/B ...............APX3000 type face mill .............................. K031 BF-DCGTooo-TA2 ..................Insert (Class G tolerance)........................... B042
APX3000RoooMooAoo .......APX3000 type screw-in end mill
BF-DNGGooo-TA4 .................Insert (Class G tolerance)........................... B025
(Metric type) ............................................ K034 BF-DNGMooo-TA2 .................Insert (Class G tolerance)........................... B026

APX3000RoooSAooo ..........APX3000 type end mill (Metric type) .......... K032 BLSoo......................................Clamp screw ...............................................M003
APX3000URoooSAoooo .....APX3000 type end mill ...................... K030,K031 BM-CNGMooo-TA2 ................Insert (Class G tolerance)........................... B023
APX4000-oooAooRA ............APX4000 type face mill (Metric type) ......... K041 BM-DNGMooo-TA2 ................Insert (Class G tolerance)........................... B026
APX4000RooooooA .............APX4000 type face mill (Metric type) ......... K042 BM-TNGMooo-TA3.................Insert (Class G tolerance)........................... B031
APX4000RoooMooAoo .......APX4000 type screw-in end mill
BOE4Roooo ...........................BOE type face mill ...................................... K109
(Metric type) ............................................ K042 BOE4RooooC/X .....................BOE type face mill ...................................... K109
APX4000RoooSA32ooo ......APX4000 type end mill (Metric type) .......... K040 BOE4RoooW20 ......................BOE type end mill ....................................... K108
APX4000URoooooo .............APX4000 type face mill .............................. K039 BOE4S06U ................................Clamp screw ...............................................M008
APX4000URoooSA/FAoooo ...APX4000 type end mill ............................... K038 BOERooooA/C/E/F ................BOE type face mill ...................................... K109
APX4K-oooAooAooRA ..........APX4000 type end mill (Metric type) .......... K047 BOERoooW20 ........................BOE type end mill ....................................... K108
APX4KRoooooAooooooA ...APX4000 type end mill (Metric type) .......... K047 BRAoooo ...............................BRA type drill (Inch type) .............................L130
APX4KR06316CA056A ............APX4000 type end mill (Metric type) .......... K047 BRAooooSoo .......................BRA type drill (Metric type) ..........................L131
APX4KURooooWAooooA ...APX4000 type end mill ............................... K046 BRPoooRoooELSoo ..........BRP type end mill ....................................... K104
APX4KUR0209A16A ................APX4000 type end mill ............................... K046 BRPoooRoooELWoo .........BRP type end mill ....................................... K104
APX4KUR2516CA22A..............APX4000 type end mill ............................... K046 BRPoooRoooLWoo ............BRP type end mill ....................................... K104
AQXRoooMooAoo...............AQX type screw-in end mill (Metric type) ... K083 BRPoooRoooWoo ..............BRP type end mill ....................................... K104
AQXRoooSA/SNooS/L .........AQX type end mill (Metric type) .................. K083 BRPoUPRoooo .....................BRP type face mill ...................................... K105
AQXURoooSA/WAooS/L ......AQX type end mill ....................................... K080 BRPoUPRooooC/E/X ............BRP type face mill ...................................... K105
ARXooRoooMooAoo .........ARX type screw-in end mill (Metric type).... K101 BRSoooo................................BRS type drill (Inch type) .............................L132
ARXooRoooSAooLW ..........ARX type end mill (Metric type) .................. K100 BRSooooSoo .......................BRS type drill (Metric type) ..........................L133
ARXooRoooSAooS .............ARX type end mill (Metric type) .................. K099 BRS105 .....................................Clamp screw (For BRE type end mill) ........M003
ASX400-ooooooR ................ASX400 type face mill (Metric type) ........... K024 BSPRoooW20.........................BSP type end mill ....................................... K112
II
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
BT50-oo-ooo-ooo ...............Long arbor .................................................. K141 CCMXooooooENA/B............Insert (For LER type end mill).............J021,K078
BTAHR/L-ooo .........................External back turning holder ....................... D016 CFSPRoooWoo .....................CFSP type end mill ..................................... K114
BTAHR/Loooo-50 ..................External back turning holder ....................... D019 CGooRS-oo............................MICRO-MINI TWIN boring bar ....................F165
BTATooooooR/L-B ..............External back turning insert ...............D016,D019 CGooRS-ooB .........................MICRO-MINI TWIN boring bar ....................F165
BTAT605000RX ........................External back turning insert ...............D016,D019 CLo ...........................................Clamp bridge ..............................................M014
BTBTooooooR/L-B ..............External back turning insert ...............D017,D020 CLoo ........................................Clamp bridge ..............................................M014
BTBT606000R/L .......................External back turning insert ...............D017,D020 CNGooo ..................................Insert (Class G tolerance)........................... B035
BTVHR-ooo ............................External back turning holder ....................... D018 CNGGoooFJ ...........................Insert (Class G tolerance)........................... A068
BTVHRoooo-75......................External back turning holder ....................... D021 CNGGoooFJ-P .......................Insert (Class G tolerance)........................... A068
BTVHRoooo-75F ...................External back turning holder ....................... D021 CNGGoooMJ ..........................Insert (Class G tolerance)........................... A069
BTVTooooooR-B..................External back turning insert ...............D018,D021 CNGGoooPK ..........................Insert (Class G tolerance)........................... A068
BXD4000-oooA/BooRA/RB...BXD4000 type face mill (Metric type) ......... K064 CNMAooo ...............................Insert (Class M tolerance) ........A073,B024,B054
BXD4000Roooo .....................BXD4000 type face mill .............................. K063 CNMGooo ...............................Insert (Class M tolerance) .......................... A071
BXD4000Rooooooo ............BXD4000 type face mill (Metric type) ......... K064 CNMGoooC ............................Insert (Class M tolerance) .......................... A069
BXD4000RooooB ..................BXD4000 type face mill .............................. K063 CNMGoooFH ..........................Insert (Class M tolerance) .......................... A068
BXD4000RoooSAooooo ....BXD4000 type end mill (Metric type) .......... K065 CNMGoooFS ..........................Insert (Class M tolerance) .......................... A068
BXD4000RoooSAooS/SB.....BXD4000 type end mill ............................... K062 CNMGoooFY ..........................Insert (Class M tolerance) .......................... A068
CNMGoooGH..........................Insert (Class M tolerance) .......................... A072
CNMGoooGJ ..........................Insert (Class M tolerance) .......................... A072

CNMGoooHAS .......................Insert (Class M tolerance) .......................... A073
CoooR-BLS ............................MICRO-MINI boring bar.............................. E031 CNMGoooMA .........................Insert (Class M tolerance) .......................... A070
CoooSCLCRoo .....................MICRO-DEX holder (Carbide shank) ......... E029 CNMGoooMH .........................Insert (Class M tolerance) .......................... A070
CoooSWUBRoo ....................MICRO-DEX holder (Carbide shank) ......... E029 CNMGoooMJ ..........................Insert (Class M tolerance) .......................... A069
C07KSTUCR06 .........................MICRO-DEX holder (Carbide shank) ......... E030 CNMGoooMP..........................Insert (Class M tolerance) .......................... A070
C2MHA ......................................Carbide end mill (Metric type).......................I190 CNMGoooMS..........................Insert (Class M tolerance) .......................... A071
C2SA .........................................Carbide end mill (Metric type).......................I188 CNMGoooMW.........................Insert (Class M tolerance) .......................... A071
C3SA .........................................Carbide end mill (Metric type).......................I189 CNMGoooSA ..........................Insert (Class M tolerance) .......................... A069
C3SARB ....................................Carbide end mill (Metric type).......................I191 CNMGoooSH ..........................Insert (Class M tolerance) .......................... A069
CAS51T .....................................Clamp screw (For BF407 type face mill) ....M003 CNMGoooSW .........................Insert (Class M tolerance) .......................... A069
CBooRS...................................MICRO-MINI TWIN boring bar ................... E032 CNMGoooSY ..........................Insert (Class M tolerance) .......................... A069
CBooRS-B ...............................MICRO-MINI TWIN boring bar ................... E032 CNMMoooHV ..........................Insert (Class M tolerance) .......................... A073
CBC4 .........................................Chipbreaker ................................................M015 CNMMoooHX ..........................Insert (Class M tolerance) .......................... A072
CBN2XLB..................................CBN end mill (Metric type)............................I186 CNMMoooHXD .......................Insert (Class M tolerance) .......................... A073
CBN2XLRB ...............................CBN end mill (Metric type)............................I187 CNMMoooHZ ..........................Insert (Class M tolerance) .......................... A072
CBR4 .........................................Chipbreaker ................................................M015 CNMPooo ...............................Insert (Class M tolerance) .......................... A071
CBSo ........................................Chipbreaker ................................................M015 CPGTooo ................................Insert (Class G tolerance).................. A107,B058
CBSoD .....................................Chipbreaker ................................................M015 CPGToooR/LF ........................Insert (Class G tolerance)........................... A107
CBT3 .........................................Chipbreaker ................................................M015 CPMHoooFV ...........................Insert (Class M tolerance) .......................... A107
CCEToooR/LSN .....................Insert (Class E tolerance) ........................... A105 CPMHoooMV ..........................Insert (Class M tolerance) .......................... A108
CCEToooR/LSR .....................Insert (Class E tolerance) ........................... A104 CPMHoooR/LF .......................Insert (Class M tolerance) .......................... A107
CCEToooR/LWSN ..................Insert (Class E tolerance) ........................... A105 CPMHoooSV...........................Insert (Class M tolerance) .......................... A107
CCGHoooR/LF .......................Insert (Class G tolerance)........................... A102 CPMToooMQ ..........................Insert (Class M tolerance) .......................... A108
CCGToooooL-F ....................Insert (Class G tolerance)........................... A102 CPMToooSQ...........................Insert (Class M tolerance) .......................... A107
CCGToooAZ ...........................Insert (Class G tolerance)........................... A101 CPMT1205ZPEN-Mo ................Insert (For PMR type end mill)............J023,K139
CCGToooFJ............................Insert (Class G tolerance)........................... A101 CPMXooo................................Insert (Class M tolerance) .......................... A108
CCGToooFJ-P ........................Insert (Class G tolerance)........................... A101 CRooRS...................................MICRO-MINI TWIN boring bar ................... E033
CCGToooMJ ...........................Insert (Class G tolerance)........................... A103 CRooRS-B ...............................MICRO-MINI TWIN boring bar ................... E033
CCGToooMJ-P .......................Insert (Class G tolerance)........................... A103 CR4 ...........................................Stop ring (For SRE type end mill) ...............M013
CCGToooR/LSN .....................Insert (Class G tolerance)........................... A105 CSooooooT ..........................Clamp screw ...............................................M003
CCGToooR/LSS .....................Insert (Class G tolerance)........................... A103 CSooooooTS ........................Clamp screw ...............................................M003
CCGToooSMG........................Insert (Class G tolerance)........................... A106 C-SCLCR/L-ooo .....................Screw clamp type boring bar
CCGWoooVo .........................Insert (Class G tolerance)........................... A106
(Carbide shank) ...................................... E013
CCMHoooMV ..........................Insert (Class M tolerance) .......................... A103 C-SDQCR/L-ooo .....................Screw clamp type boring bar
CCMHoooSV ..........................Insert (Class M tolerance) .......................... A102
(Carbide shank) ...................................... E014
CCMTooo................................Insert (Class M tolerance) .......................... A103 C-STUCR/L-ooo .....................Screw clamp type boring bar
CCMToooFV ...........................Insert (Class M tolerance) .......................... A101
(Carbide shank) ...................................... E016
CCMToooMW .........................Insert (Class M tolerance) .......................... A104 CSVHR/L-ooo .........................External turning holder ............................... D041
CCMToooSW ..........................Insert (Class M tolerance) .......................... A102 CSVHR/Loooo .......................External turning holder ............................... D044
CCMWooo ..............................Insert (Class M tolerance) ........A106,B040,B058 CSVTBoooR/L ........................External back turning insert ...............D042,D045
III
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
CSVTBoooR-B .......................External back turning insert ...............D042,D045 DCGToooSMG........................Insert (Class G tolerance)........................... A112
CSVTBXL ..................................External back turning,
DCGWooo...............................Insert (Class G tolerance)........................... A113
copying insert .................................D042,D045 DCKoooo ...............................Clamp bridge ..............................................M014

CSVTCooooR/L .....................External cutting off insert ...................D042,D045 DCLNR/L-ooo .........................Double clamp type holder ........................... C006
CSVTCooooR-B.....................External cutting off insert ...................D042,D045 DCMTooo................................Insert (Class M tolerance) ................. A110,A111
CSVTFoooR/L ........................External front turning insert ...............D041,D044 DCMToooFV ...........................Insert (Class M tolerance) .......................... A109
CSVTFoooR/L-B.....................External front turning insert ...............D041,D044 DCMToooMV ..........................Insert (Class M tolerance) .......................... A111
CSVTFXL ..................................External front turning copying insert ...D041,D044 DCMToooSV ...........................Insert (Class M tolerance) .......................... A110
CSVTGoooooR/L ..................External grooving insert .....................D043,D046 DCMWooo ..............................Insert (Class M tolerance) ........A113,B043,B059
CSVTT60050RR/L ....................External threading insert....................D043,D046 DCRNR/L-ooo.........................Double clamp type holder ........................... C008
C-SWL0502R/LS.......................Screw clamp type boring bar
DCSo ........................................Spring ..............................................C007 C027
(Carbide shank) ...................................... E017 DCSVN32 ..................................Shim ...........................................................M009

C-SWL0504R/L .........................Screw clamp type boring bar
DDJNR/L-ooo .........................Double clamp type holder ........................... C010
(Carbide shank) ...................................... E017 DDPNN-164...............................Double clamp type holder ........................... C011
C-SWL05S3R/LM......................Screw clamp type boring bar
DDQNR/L-164 ...........................Double clamp type holder ........................... C012
(Carbide shank) ...................................... E017 DEGXoooR/L ..........................Insert (Class G tolerance)........................... A114

C-SWLOR/L-ooo ....................Screw clamp type boring bar
DEGXoooR/LF ........................Insert (Class G tolerance).................. A114,B065
(Carbide shank) ...................................... E019 DF2MB ......................................Diamond coated end mill (Metric type) .........I180
CTooRS-Mo ............................MICRO-MINI TWIN boring bar ................... G039 DF2XLB.....................................Diamond coated end mill (Metric type) .........I181
CTooRS-Moo .........................MICRO-MINI TWIN boring bar ................... G039 DF3XB .......................................Diamond coated end mill (Metric type) .........I183
CTooRS-MooB.......................MICRO-MINI TWIN boring bar ................... G039 DF4JC .......................................Diamond coated end mill (Metric type) .........I178
CTooRS-MoB .........................MICRO-MINI TWIN boring bar ................... G039 DF4XL .......................................Diamond coated end mill (Metric type) .........I179
CTAHR/L-ooo .........................External cutting off holder ........................... D026 DFPSRB ....................................Diamond coated end mill (Metric type) .........I184
CTAHR/Loooo-120 ................External cutting off holder ........................... D028 DGKoR/L ..................................Clamp bridge (For DG holder) ....................M014
CTAHR/L1010-120S .................External cutting off holder ........................... D028 DGS51 .......................................Clamp screw (For DG holder).....................M003
CTAHR-oooS ..........................External cutting off holder ........................... D026 DNGooo ..................................Insert (Class G tolerance)........................... B035
CTAToooooooR/Lo ............External cutting off insert ...................D027,D029 DNGAooo ...............................Insert (Class G tolerance).........A078,B027,B054
CTAToooooooR/Lo-B ........External cutting off insert ...................D027,D029 DNGGoooFJ ...........................Insert (Class G tolerance)........................... A074
CTAToooooooRo-BX .........External cutting off insert ...................D027,D029 DNGGoooPK ..........................Insert (Class G tolerance)........................... A074
CTBHR/L-ooo .........................External back turning,
DNGGoooR/L .........................Insert (Class G tolerance)........................... A077
cutting off holder ............................D017,D030 DNGMoooMJ ..........................Insert (Class G tolerance)........................... A075

CTBHR/Loooo-160 ................External back turning,
DNMAooo ...............................Insert (Class M tolerance) .......................... A078
cutting off holder ............................D020,D031 DNMGooo ...............................Insert (Class M tolerance) .......................... A077
CTBToooooooR/Lo-B ........External cutting off insert ...................D030,D031 DNMGoooC ............................Insert (Class M tolerance) .......................... A075
CTCHR/Loooo-200 ................External cutting off holder ........................... D032 DNMGoooFH ..........................Insert (Class M tolerance) .......................... A074
CTCToooooooo-B ..............External cutting off insert ............................ D032 DNMGoooFS ..........................Insert (Class M tolerance) .......................... A074
CTDHR/Loooo-ooo..............External cutting off holder ........................... D033 DNMGoooFY ..........................Insert (Class M tolerance) .......................... A074
CTDToooooooo-B ..............External cutting off insert ............................ D033 DNMGoooGH..........................Insert (Class M tolerance) .......................... A077
CTDToooooooo-BS ............External cutting off insert ............................ D033 DNMGoooGJ ..........................Insert (Class M tolerance) .......................... A077
CTEooTooo ...........................Shim ........................................................... G012 DNMGoooMA .........................Insert (Class M tolerance) .......................... A076
CTEHR/Loooo-ooo ..............External cutting off holder ........................... D034 DNMGoooMH .........................Insert (Class M tolerance) .......................... A076
CTEToooooooo-B ..............External cutting off insert ............................ D034 DNMGoooMJ ..........................Insert (Class M tolerance) .......................... A075
CTEToooooooo-BS ............External cutting off insert ............................ D034 DNMGoooMP..........................Insert (Class M tolerance) .......................... A076
CTIooTooo ............................Shim ........................................................... G013 DNMGoooMS..........................Insert (Class M tolerance) .......................... A077
DNMGoooSA ..........................Insert (Class M tolerance) .......................... A074
DNMGoooSH ..........................Insert (Class M tolerance) .......................... A075

DNMGoooSY ..........................Insert (Class M tolerance) .......................... A075
DCooooT ................................Clamp screw ...............................................M003 DNMMoooHZ ..........................Insert (Class M tolerance) .......................... A078
DCEToooR/LSN .....................Insert (Class E tolerance) .................. A111,A112 DNMXoooMW .........................Insert (Class M tolerance) .......................... A077
DCEToooR/LSR .....................Insert (Class E tolerance) ........................... A111 DNMXoooSW..........................Insert (Class M tolerance) .......................... A075
DCEToooR/LWSN ..................Insert (Class E tolerance) ........................... A112 DRGNR/L-ooo ........................Double clamp type holder ........................... C013
DCGToooAZ ...........................Insert (Class G tolerance)........................... A109 DS2LB .......................................DIAMOND STAR end mill (Inch type)...........I023
DCGToooFJ............................Insert (Class G tolerance)........................... A109 DS2LS .......................................DIAMOND STAR end mill (Inch type)...........I016
DCGToooFJ-P ........................Insert (Class G tolerance)........................... A109 DS2MRB ...................................DIAMOND STAR end mill (Inch type)...........I032
DCGToooMJ ...........................Insert (Class G tolerance)........................... A110 DS2MS ......................................DIAMOND STAR end mill (Inch type)...........I015
DCGToooMJ-P .......................Insert (Class G tolerance)........................... A110 DS2SB.......................................DIAMOND STAR end mill (Inch type)...........I022
DCGToooR/LF ........................Insert (Class G tolerance)........................... A109 DS2SRB ....................................DIAMOND STAR end mill (Inch type)...........I031
DCGToooR/LSN .....................Insert (Class G tolerance)........................... A112 DS2SRB...Ao ...........................DIAMOND STAR end mill (Inch type)...........I035
DCGToooR/LSS .....................Insert (Class G tolerance)........................... A110 DS2SRB...NAo .........................DIAMOND STAR end mill (Inch type)...........I036
IV
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
DS2SS .......................................DIAMOND STAR end mill (Inch type)...........I014 GTAHR/Loooo-20 ..................External grooving holder............................. D024
DS3MC ......................................DIAMOND STAR end mill (Inch type)...........I018 GTAHR/Loooo-20S................External grooving holder............................. D024
DS3MH...SS ..............................DIAMOND STAR end mill (Inch type)...........I039 GTAHR/L-oooS ......................External grooving holder............................. D022
DS3MHB...SS............................DIAMOND STAR end mill (Inch type)...........I043 GTAToooooooR/L-E ...........External grooving insert .....................D023,D025
DS3MHH60 ...............................DIAMOND STAR end mill (Inch type)...........I027 GTAToooooooR/L-U ...........External grooving insert .....................D022,D024
DS3MHHRB ..............................DIAMOND STAR end mill (Inch type)...........I048 GTAToooooooR-VT ............External grooving insert .....................D023,D025
DS3MHR...A ..............................DIAMOND STAR end mill (Inch type)...........I037 GTBHR/L-ooo .........................External grooving holder............................. D022
DS3MHRB...SS .........................DIAMOND STAR end mill (Inch type)...........I045 GTBHR/Loooo-30 ..................External grooving holder............................. D024
DS3SB.......................................DIAMOND STAR end mill (Inch type)...........I024 GTBHR/Loooo-30S................External grooving holder....................D024,D024
DS3SC.......................................DIAMOND STAR end mill (Inch type)...........I017 GTBHR/L-oooS ......................External grooving holder............................. D022
DS3SH...SS ...............................DIAMOND STAR end mill (Inch type)...........I038 GTBToooooooR-VT ............External grooving insert .....................D023,D025
DS3SHB...SS ............................DIAMOND STAR end mill (Inch type)...........I042 GTBToooooVoR/L-E ............External grooving insert .....................D023,D025
DS3SHRB...SS..........................DIAMOND STAR end mill (Inch type)...........I044 GTBToooooVoR/L-U............External grooving insert .....................D022,D024
DS4LB .......................................DIAMOND STAR end mill (Inch type)...........I026 GTCHR/L-ooo .........................External grooving holder............................. D022
DS4LC .......................................DIAMOND STAR end mill (Inch type)...........I021 GTCHR/Loooo-30 ..................External grooving holder............................. D024
DS4LC...CB...............................DIAMOND STAR end mill (Inch type)...........I030 GTCHR/Loooo-30S................External grooving holder............................. D024
DS4MC ......................................DIAMOND STAR end mill (Inch type)...........I020 GTCHR/L-oooS ......................External grooving holder............................. D022
DS4MC...CB ..............................DIAMOND STAR end mill (Inch type)...........I029 GTCToooooVoR/L-E ............External grooving insert .....................D023,D025
DS4MRB ...................................DIAMOND STAR end mill (Inch type)...........I034 GTCToooooVoR/L-U............External grooving insert .............................. D022
DS4SB.......................................DIAMOND STAR end mill (Inch type)...........I025 GTSo ........................................Clamp screw ...............................................M004
DS4SC.......................................DIAMOND STAR end mill (Inch type)...........I019 GYoR/Looooo90o-oooR/L ...GY type holder (Internal 90 type) ... F134 F144
DS4SRB ....................................DIAMOND STAR end mill (Inch type)...........I033 GYoR/Looo90o-oooR/L ......GY type holder (Internal 90 type) ... F140 F144
DS5LH...SS ...............................DIAMOND STAR end mill (Inch type)...........I041 GY05016S .................................Clamp screw ...............................................M004
DS5MH...SS ..............................DIAMOND STAR end mill (Inch type)...........I040 GY06013M ................................Clamp screw ...............................................M004
DS5MHRB...SS .........................DIAMOND STAR end mill (Inch type)...........I047 GY1BooooooooN ...............Insert (For GY holder)..................................F013
DS5SHRB...SS..........................DIAMOND STAR end mill (Inch type)...........I046 GY1GooooooooN-GFGS ....CBN Insert (For GY holder) .........................F013
DS6MHH60 ...............................DIAMOND STAR end mill (Inch type)...........I028 GY2BooooooooN ...............Insert (For GY holder)..................................F013
DS6MHHRB ..............................DIAMOND STAR end mill (Inch type)...........I049 GY2MooooooooN-BM ........Insert (For GY holder)..................................F013
DSDNN-ooo ............................Double clamp type holder ........................... C016 GY2MooooooooN-GM ........Insert (For GY holder)..................................F012
DSKNR/L-ooo .........................Double clamp type holder ........................... C017 GY2MooooooooN-GS ........Insert (For GY holder)..................................F012
DSRNR/L-ooo .........................Double clamp type holder ........................... C014 GY2MooooooooN-GU ........Insert (For GY holder)..................................F012
DSSNR/L-ooo .........................Double clamp type holder ........................... C015 GY2MooooooooN-MM ........Insert (For GY holder)..................................F013
DTCNN-ooo ............................Double clamp type holder ........................... C022 GY2MooooooooN-MS ........Insert (For GY holder)..................................F013
DTFNR/L-ooo .........................Double clamp type holder ........................... C022 GY2MooooooooR/L05-GM...Insert (For GY holder)..................................F012
DTGNR/L-ooo .........................Double clamp type holder ........................... C018 GYHR/Looooo00-oooR/L ...GY type holder (External 00 type) .......................
DVJNR/L-ooo .........................Double clamp type holder ........................... C024
F014 F024,F030 F040,F054 F080,F090 F116
DVPNR/L-ooo .........................Double clamp type holder ........................... C025 GYHR/Looooo90-oooR/L ...GY type holder (External 90 type) .......................
F026 F028,F042 F044,F082 F088,F118 F124
DVVNN-ooo ............................Double clamp type holder ........................... C025
DWLNR/L-ooo ........................Double clamp type holder ........................... C027 GYMooR/Lo-ooo ..................Modular Blade (For GY holder) ........F012F144
ECMPRoooWoo ....................ECMP type end mill .................................... K113 H100TH-Boo-ooo ..................HSK boring bar holder ................................ H021
H100TH-EN3232R/L-130 ..........HSK external turning tool holder................. H020
H100TH-EV3232R/L-180 ..........HSK external turning tool holder................. H019

H63TH-AoooDCLNR/L12 .......HSK DCLN type holder............................... H008
FBP415Rooooo ....................FBP415 type face mill................................. K018 H63TH-Boo-oo .......................HSK boring bar holder ................................ H021
FC400890T................................Clamp screw (For AL type boring bar)........M004 H63TH-DCLNL-L12-3 ...............HSK DCLN type holder............................... H008
FSL5oooR...............................Grooving and threading boring bar ....F162,G036 H63TH-DCLNR/L-DX12 ............HSK DCLN type holder............................... H006
FSWLoooRS/RM ....................Screw clamp boring bar .............................. E018 H63TH-DCMNN-H/L12..............HSK DCMN type holder.............................. H007
FSWL1ooR ..............................Screw clamp boring bar .............................. E018 H63TH-DDJNL-L15-3 ...............HSK DDJN type holder ............................... H011
FSWL2ooR ..............................Screw clamp boring bar .............................. E018 H63TH-DDJNR/L-DX15 ............HSK DDJN type holder ............................... H009
H63TH-DDNNN-H/L15 ..............HSK DDNN type holder .............................. H010
H63TH-EV2020R/L-105-3 .........HSK external turning tool holder................. H021

H63TH-EV2525R/L-112 ............HSK external turning tool holder................. H019
GCMToooooo-Uo ................Insert (For TAF type drill).............................L127 H63TH-MGHR/L-oooooo .....HSK MG type holder................................... H014
GPGToooooo-Uo.................Insert (For TAF type drill).............................L127 H63TH-MMTENR-H/L16 ...........HSK MMT type holder ................................ H016
GPMToooooo-Uo ................Insert (For TAF type drill).............................L127 H63TH-MMTER-DX16...............HSK MMT type holder ................................ H016
GTAHR/L-ooo .........................External grooving holder............................. D022 H63TH-MTHR/L-DX43 ..............HSK MT type holder ................................... H017
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
H63TH-PCLNR/L-DX12 ............HSK PCLN type holder ............................... H006 LLCLoo....................................Clamp lever ................................................M013
H63TH-PCMNN-H/L12 ..............HSK PCMN type holder .............................. H007 LLCLooo .................................Clamp lever ................................................M013
H63TH-PDJNR/L-DX15 ............HSK PDJN type holder ............................... H009 LLCSooo.................................Clamp screw ...............................................M004
H63TH-PDNNN-H/L15 ..............HSK PDNN type holder .............................. H010 LLPoo ......................................Shim pin......................................................M013
H63TH-PRDCN-H/L12 ..............HSK PRDC type holder .............................. H012 LLSCNoo .................................Shim ...........................................................M010
H63TH-PRGCR/L-DX12............HSK PRGC type holder .............................. H012 LLSCPoo .................................Shim ...........................................................M010
H63TH-SVPBR/L-DX16 ............HSK SVPB type holder ............................... H013 LLSDNoo .................................Shim ...........................................................M010
H63TH-SVVBN-H/L16...............HSK SVVB type holder ............................... H013 LLSDPoo .................................Shim ...........................................................M010
HDS10031 .................................Clamp screw ...............................................M007 LLSRN123.................................Shim ...........................................................M010
HDSU37513 ..............................Clamp screw ...............................................M007 LLSSN42 ...................................Shim ...........................................................M010
HFF08043H ...............................Clamp screw ...............................................M008 LLSSP42 ...................................Shim ...........................................................M010
HGM-PTo/o..............................Plug ................................................ H012 H019 LLSTNoo .................................Shim ...........................................................M010
HKYooD...................................Driver wrench .............................................M002 LLSTP32 ...................................Shim ...........................................................M010
HKYooF ...................................Flag wrench ................................................M002 LLSWNoo ................................Shim ...........................................................M010
HKYooL ...................................Long L-wrench ............................................M002 LLSWP42 ..................................Shim ...........................................................M010
HKYooR...................................L-wrench .....................................................M002 LSoo ........................................Clamp screw ...............................................M004
HKYooT ...................................T-wrench .....................................................M002 LSooT ......................................Clamp screw ...............................................M004
HKYooW ..................................Flag wrench ................................................M002 LSooTS....................................Clamp screw ...............................................M004
HSCooooo .............................Clamp screw ...............................................M008 LS0622T ....................................Clamp screw ...............................................M004
HSCoooooH ..........................Clamp screw ...............................................M008
HSCUoooooH .......................Clamp screw (For cutter) ............................M008
HSCUCooooo .......................Clamp screw (For cutter) ............................M008
HSCUFooooo ........................Clamp screw (For cutter) ............................M008 MAEooooMB..........................MAS type drill (Metric type) ..............L068 L073
HSSooooo .............................Clamp screw ...............................................M002 MASoooooMB .......................MAS type drill (Inch type) ............................L066
MASooooLB/MB ....................MAS type drill (Metric type) ..............L068 L073
MBAU100016H .........................Clamp screw (For AJX type cutter).............M008

MBAU75016H ...........................Clamp screw (For AJX type cutter).............M008
ICSNooo .................................Shim ...........................................................M009 MBDooooooo ......................Insert (For MBD type end mill)............J022,K125
IDSNooo .................................Shim ...........................................................M009 MBDooooooSB ....................MBD type end mill ...................................... K125
IRSNoo ....................................Shim ...........................................................M009 MBFooooooo .......................Insert (For MBD type end mill)............J022,K125
ISSNooo..................................Shim ...........................................................M009 MBNooooooo ......................Insert (For MBD type end mill)............J022,K124
ITSNooo ..................................Shim ...........................................................M009 MBNooooooSA/B/C .............MBN type end mill ...................................... K124
IVSNooo..................................Shim ...........................................................M010 MBNooooooTB ....................MBN type end mill ...................................... K124
IWSNooo.................................Shim ...........................................................M010 MCFNR/L-ooo.........................Multiple clamp holder.................................. C009
MCFNR/L-oooo ......................Multiple clamp holder.................................. C009
MCGNR/L-ooo ........................Multiple clamp holder.................................. C008

MCGNR/L-oooo .....................Multiple clamp holder.................................. C008
JDMTooooooZDSR-JM/ST...Insert (For AJX type cutter) ...... J012,K095,K137 MCLNR/L-ooo.........................Multiple clamp holder.................................. C007
JDMWooooooZDSR-FT .......Insert (For AJX type cutter) ...... J012,K095,K137 MCLNR/L-oooo ......................Multiple clamp holder.................................. C007
JOMTooooooZZSR-JM ........Insert (For AJX type cutter) ...... J012,K095,K137 MCRNR/L-oooo .....................Multiple clamp holder.................................. C009
JOMWooooooZZSR-FT .......Insert (For AJX type cutter) ...... J012,K095,K137 MCSooooX3DB......................MCS type drill ..............................................L092
JPMT060204-E .........................Insert (For milling)........................................ J032 MDJNR/L-ooo .........................Multiple clamp holder.................................. C010
JPMXoo0412-JM .....................Insert (For SPX type end mill) ............J026,K072 MDJNR/L-oooo ......................Multiple clamp holder.................................. C010
JPMXoo0412-WH ....................Insert (For SPX type end mill) ............J026,K072 MDPNN-oooD .........................Multiple clamp holder.................................. C011
JSSo .........................................Shim screw .................................................M004 M-FSCLCR/L-ooo-C ...............Screw clamp DIMPLE BAR
(Heavy metal shank) ............................... E006
M-FSCLPR/L-ooo-C ...............Screw clamp DIMPLE BAR

KGBNoo ..................................Block (For UG holder)..................................F158 M-FSDQCR/L-ooo-C ..............Screw clamp DIMPLE BAR

KGBNoo-ooooo-30..............Tool block (For UG holder) ..........................F158
KGC1.........................................Clamp bridge (For UG tool block) ...............M014 M-FSDUCR/L-ooo-C...............Screw clamp DIMPLE BAR
KGToN .....................................Insert (For UG holder) .................................F159
KGToR/L ..................................Insert (For UG holder) .................................F159 M-FSTUPR/L-ooo-C ...............Screw clamp DIMPLE BAR
KNMX5XoR ..............................Insert (Class M tolerance) .......................... A098
KNUXoooRMo .......................Insert (Class U tolerance) ........................... A098 M-FSVJBR/L-ooo-C ...............Screw clamp DIMPLE BAR
L
LERooooWoo .......................LER type end mill ....................................... K078
VI
M-FSVJCR/L-ooo-C ...............Screw clamp DIMPLE BAR

INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
M-FSVPBR/L-ooo-C ...............Screw clamp DIMPLE BAR
PRODUCT NAME
PAGE
MS4EC ......................................MSTAR end mill (Metric type).......................I077
(Heavy metal shank) ............................... E010 MS4JC.......................................MSTAR end mill (Metric type).......................I070
M-FSVPCR/L-ooo-C ...............Screw clamp DIMPLE BAR
MS4LT .......................................MSTAR end mill (Metric type).......................I101
(Heavy metal shank) ............................... E010 MS4LTB ....................................MSTAR end mill (Metric type).......................I108
M-FSVUBR/L-ooo-C ...............Screw clamp DIMPLE BAR
MS4MC......................................MSTAR end mill (Metric type).......................I069
(Heavy metal shank) ............................... E009 MS4MRB ...................................MSTAR end mill (Metric type).......................I093
M-FSVUCR/L-ooo-C ...............Screw clamp DIMPLE BAR
MS4SC ......................................MSTAR end mill (Metric type).......................I068
(Heavy metal shank) ............................... E009 MS4XL.......................................MSTAR end mill (Metric type).......................I071
M-FSWUBR/L-ooo-C ..............Screw clamp DIMPLE BAR
MS4XL.......................................MSTAR end mill (Inch type)..........................I074
(Heavy metal shank) ............................... E009 MS4XLB ....................................MSTAR end mill (Inch type)..........................I086
M-FSWUPR/L-ooo-C ..............Screw clamp DIMPLE BAR
M-SCLCR-ooo ........................Screw clamp type boring bar
MGDoo ....................................Driver (For MICRO-MGS type drill) .............L059 MSDNN-oo ..............................Multiple clamp type holder .......................... C016
MGSooooLooB ....................MICRO-MGS type drill (Metric type) ............L058 MSDNN-ooo............................Multiple clamp type holder .......................... C016
MGTR/L43ooo ........................Insert (For grooving) ................................... H015 MSEooooSB ..........................MSE type drill (Metric type) ................L054,L055
MHSooooLoooB ..................MHS type drill (Metric type) ..............L082 L088 MSJHD ......................................MSTAR end mill (Metric type).......................I065
MK1KS ......................................Anti seize lubricant .....................................M016 MSKNR/L-oo ...........................Multiple clamp type holder .......................... C017
MLGooooL .............................Insert (For FSL5 type boring bar) ......F164,G038 MSKNR/L-ooo ........................Multiple clamp type holder .......................... C017
MLGooWoooL .......................Insert (For FSL5 type boring bar) ......F164,G038 MSKNR/L-oooo......................Multiple clamp type holder .......................... C017
MLPooooL .............................Insert (For FSL5 type boring bar) ......F164,G038 MSMHD .....................................MSTAR end mill (Metric type).......................I063
MLTooooL..............................Insert (For FSL5 type boring bar) ......F164,G038 MSMHDRB ................................MSTAR end mill (Metric type).......................I095
MMSooooX3DB/5DB .............MMS type drill (Metric type) ..............L060 L063 MSMHZD ...................................MSTAR end mill (Inch type)..........................I067
MMTooERooooooo............Insert (For external threading) .................... G016 MSMHZD ...................................MSTAR end mill (Metric type).......................I066
G018,G020 MSP0300SB ..............................MSP starter drill (Metric type) ......................L056
MMTooERooooooo-S ........Insert (For external threading) .................... G014 MSRNR/L-oo ...........................Multiple clamp type holder .......................... C014
MMTooIRooooooo .............Insert (For internal threading) ..................... G017 MSRNR/L-ooo ........................Multiple clamp type holder .......................... C014
G019,G021 MSRNR/L-oooo......................Multiple clamp type holder .......................... C014
MMTooIRooooooo-S .........Insert (For internal threading) ..................... G015 MSSHD......................................MSTAR end mill (Metric type).......................I062
MMTER-ooo............................Threading holder ........................................ G012 MSSNR/L-oo ...........................Multiple clamp type holder .......................... C015
MMTER-oooSM ......................Threading holder ........................................ D038 MSSNR/L-oooo ......................Multiple clamp type holder .......................... C015
MMTIRooo-o.oo-o.o-C ........Threading holder ........................................ G013 M-SWLOR/L-ooo ....................Screw clamp type boring bar
M-MWLNR/L-ooo-C ................Multiple clamp type boring bar
(Heavy metal shank) ............................... E027 M-SWLOR/L-ooo-C ................Screw clamp type boring bar
MNSooooLB ..........................MNS type drill (Metric type) ..............L074 L079
MNSooooX10/20/30DB..........MNS type drill (Metric type) ..............L074 L079 MTANR/L-ooo.........................Multiple clamp type holder .......................... C020
MPMMooo...............................Insert (For ECMP type end mill) .........J020,K113 MTANR/L-oooX ......................Multiple clamp type holder .......................... C020
MPMX120412-JM......................Insert (For SPX type end mill) ............J026,K072 MTCNN-ooo ............................Multiple clamp type holder .......................... C021
MPMX120412-WH.....................Insert (For SPX type end mill) ............J026,K072 MTCNN-oooX .........................Multiple clamp type holder .......................... C021
MRGNR/L-ooo ........................Multiple clamp type holder .......................... C013 MTCNN-ooX ............................Multiple clamp type holder .......................... C021
MRGNR/L-oooo .....................Multiple clamp type holder .......................... C013 MTENN-oo ...............................Multiple clamp type holder .......................... C021
MS2ES ......................................MSTAR end mill (Metric type).......................I075 MTENN-oooX..........................Multiple clamp type holder .......................... C021
MS2JS .......................................MSTAR end mill (Metric type).......................I054 MTFNR/L-oo ............................Multiple clamp type holder .......................... C023
MS2LS.......................................MSTAR end mill (Metric type).......................I055 MTFNR/L-oooo ......................Multiple clamp type holder .......................... C023
MS2MB......................................MSTAR end mill (Metric type).......................I079 MTFNR/L-ooooX ....................Multiple clamp type holder .......................... C023
MS2MD......................................MSTAR end mill (Metric type).......................I053 MTGNR/L-oooo......................Multiple clamp type holder .......................... C019
MS2MRB ...................................MSTAR end mill (Metric type).......................I090 MTGNR/L-ooooX ...................Multiple clamp type holder .......................... C019
MS2MS ......................................MSTAR end mill (Metric type).......................I051 MTJNR/L-ooo .........................Multiple clamp type holder .......................... C018
MS2MT ......................................MSTAR end mill (Metric type).......................I097 MTJNR/L-oooX .......................Multiple clamp type holder .......................... C018
MS2MTB ...................................MSTAR end mill (Metric type).......................I107 MTK1R/L ...................................Clamp bridge ..............................................M014
MS2SB ......................................MSTAR end mill (Metric type).......................I078 MTRNR/L-123X .........................Multiple clamp type holder .......................... C020
MS2SS ......................................MSTAR end mill (Metric type).......................I050 MTRNR/L-164 ...........................Multiple clamp type holder .......................... C020
MS2XB ......................................MSTAR end mill (Metric type).......................I087 MTTR/L43oooo ......................Insert (For threading) .................................. H018
MS2XL.......................................MSTAR end mill (Inch type)..........................I061 MTVOR/Loo-oo ......................Grooving and threading holder ..........F160,G034
MS2XL.......................................MSTAR end mill (Metric type).......................I056 MVJNR/L-oooo ......................Multiple clamp type holder .......................... C024
MS2XL6.....................................MSTAR end mill (Metric type).......................I059 MVLNR/L-oooo ......................Multiple clamp type holder .......................... C026
MS2XLB ....................................MSTAR end mill (Inch type)..........................I085 MWEooooMA/SA ...................MWS type drill (Metric type) .............L006 L014
MS2XLB ....................................MSTAR end mill (Metric type).......................I080 MWLNR/L-oooo .....................Multiple clamp type holder .......................... C027
MS2XLRB .................................MSTAR end mill (Metric type).......................I092 MWSoooooLB/SB/XB ...........MICRO-MWS type drill (Inch type) .....L040,L041
MS3ES ......................................MSTAR end mill (Metric type).......................I076 MWSoooooLB/X8DB ............MWS type drill (Inch type) ..................L004,L005
VII
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
MWSoooooX15/20/25/30DB...MWS type drill
PRODUCT NAME
PAGE
NP-DNGAooooo ...................CBN insert (Class G tolerance) .................. B027
(Inch extra long type) ......................L016,L017 NP-DNGAooo-oo2 ................CBN insert (Class G tolerance) .................. B025
MWSooooLB/MB/X8DB ........MWS type drill (Metric type) .............L006 L015 NP-DNGAooo-oo4 ................CBN insert (Class G tolerance) .................. B025
MWSooooLB/SB/XB..............MICRO-MWS type drill (Metric type) .....L042 L047 NP-DNGAooo-o2 ...................CBN insert (Class G tolerance) .................. B026
MWSooooX10/15/20/25/30DB...MWS type drill
NP-DNGAooo-GAWS2JR/L ...CBN insert (Class G tolerance) .................. B026
(Metric extra long type) .................L018 L024 NP-DNMAoooo ......................CBN insert (Class M tolerance) .................. B027
MWSooooX20/25/30DB .........MICRO-MWS type drill (Metric type) ......L044L047 NP-DNMAooooo ...................CBN insert (Class M tolerance) .................. B027
MZEoooooMA/SA .................MZE type drill (Inch type)....................L026,L027 NP-DNMAooo-o2 ...................CBN insert (Class M tolerance) .................. B026
MZEoooooSB ........................MICRO-MZE type drill (Inch type) ...............L050 NP-DNMMoooR/LF.................CBN insert (Class M tolerance) .................. B054
MZEooooMA/SA ....................MICRO-MZE type drill (Metric type) ............L051 NP-SNGAooo-oo2 ................CBN insert (Class G tolerance) .................. B028
MZEooooMA/SA ....................MZE type drill (Metric type)...............L028 L036 NP-SNGAooo-o2 ...................CBN insert (Class G tolerance) .................. B028
MZSoooooLB ........................MICRO-MZS type drill (Inch type) ...............L050 NP-SNGAoooGA ....................CBN insert (Class G tolerance) .................. B028
MZSoooooLB/MB .................MZS type drill (Inch type)....................L026,L027 NP-SNGAooo-GA4 .................CBN insert (Class G tolerance) .................. B028
MZSooooLB/MB ....................MICRO-MZE type drill (Metric type) ............L051 NP-SNMAoooo ......................CBN insert (Class M tolerance) .................. B029
MZSooooLB/MB ....................MZS type drill (Metric type)...............L028 L036 NP-SNMAooooo ...................CBN insert (Class M tolerance) .................. B029
MZSooooMMoo ....................STEP drill (Metric type)................................L037 NP-SNMAooo-G2 ...................CBN insert (Class M tolerance) .................. B028
NP-SNMMoooR/LF .................CBN insert (Class M tolerance) .................. B055
NP-TCGWooo-oo3 ................CBN insert (Class G tolerance) .................. B044

NP-TCGWoooGA ...................CBN insert (Class G tolerance) .................. B044
NKYooD...................................Driver wrench .............................................M002 NP-TNGAooooo ....................CBN insert (Class G tolerance) .................. B031
NKYooF ...................................Flag wrench ................................................M002 NP-TNGAooo-oo3 .................CBN insert (Class G tolerance) .................. B030
NKYooL ...................................Long L-wrench ............................................M002 NP-TNGAooo-oo6 .................CBN insert (Class G tolerance) .................. B030
NKYooR...................................L-wrench .....................................................M002 NP-TNGAooo-o3....................CBN insert (Class G tolerance) .................. B030
NKYooT ...................................T-wrench.....................................................M002 NP-TNMAoooo.......................CBN insert (Class M tolerance) .................. B031
NKYooW ..................................Flag wrench ................................................M002 NP-TNMAooooo ....................CBN insert (Class M tolerance) .................. B031
NLoo ........................................Pin ..............................................................M013 NP-TNMMoooR/LF .................CBN insert (Class M tolerance) .................. B055
NLooo .....................................Pin ..............................................................M013 NP-TPGBooo-oo3 .................CBN insert (Class G tolerance) .................. B045
NNMU200608ZEN-HK ..............Insert (For AHX640W type face mill) ....J012,K014 NP-TPGXoooo .......................CBN insert (Class G tolerance) .................. B045
NNMU200608ZEN-MK ..............Insert (For AHX640W type face mill) ....J012,K014 NP-TPGXooo-GS3..................CBN insert (Class G tolerance) .................. B045
NP-CCGB21.51GA ...................CBN insert (Class G tolerance) .................. B039 NP-TPMBoooG .......................CBN insert (Class M tolerance) .................. B045
NP-CCGB21.51-GA2 ................CBN insert (Class G tolerance) .................. B038 NP-TPMHoooR/LF..................CBN insert (Class M tolerance) .................. B061
NP-CCGWoooo......................CBN insert (Class G tolerance) ......... B039,B040 NP-TPMXoooR/LF ..................CBN insert (Class M tolerance) .................. B061
NP-CCGWooooo ...................CBN insert (Class G tolerance) .................. B039 NP-VBGToooRF .....................CBN insert (Class G tolerance) .................. B063
NP-CCGWooo-oo2 ...............CBN insert (Class G tolerance) .................. B038 NP-VBGWoooo ......................CBN insert (Class G tolerance) .................. B047
NP-CCGWooo-o2 ..................CBN insert (Class G tolerance) .................. B038 NP-VBGWooooo ...................CBN insert (Class G tolerance) .................. B047
NP-CCGWooo-GoWS2 ..........CBN insert (Class G tolerance) .................. B039 NP-VBGWooo-oo2 ................CBN insert (Class G tolerance) .................. B047
NP-CCMB21.51G ......................CBN insert (Class M tolerance) .................. B039 NP-VCGToooRF .....................CBN insert (Class G tolerance) .................. B063
NP-CCMHooo .........................CBN insert (Class M tolerance) .................. B058 NP-VCGWoooGA ...................CBN insert (Class G tolerance) .................. B048
NP-CCMWoooooo................CBN insert (Class M tolerance) .................. B058 NP-VCGWooo-GA2 ................CBN insert (Class G tolerance) .................. B048
NP-CCMWooooooF .............CBN insert (Class M tolerance) .................. B040 NP-VNGAooo-oo2 ................CBN insert (Class G tolerance) .................. B032
NP-CNGAooooo ...................CBN insert (Class G tolerance) .................. B024 NP-VNGAooo-oo4 ................CBN insert (Class G tolerance) .................. B032
NP-CNGAooo-oo2 ................CBN insert (Class G tolerance) .................. B022 NP-VNGAooo-o2 ...................CBN insert (Class G tolerance) .................. B032
NP-CNGAooo-oo4 ................CBN insert (Class G tolerance) .................. B022 NP-VNGAoooGA ....................CBN insert (Class G tolerance) .................. B033
NP-CNGAooo-ooWS2 ..........CBN insert (Class G tolerance) .................. B023 NP-VNMAoooo ......................CBN insert (Class M tolerance) .................. B033
NP-CNGAooo-o2 ...................CBN insert (Class G tolerance) .................. B023 NP-VNMAooooo ...................CBN insert (Class M tolerance) .................. B033
NP-CNGAooo-GAWS4 ...........CBN insert (Class G tolerance) .................. B022 NP-VNMAooo-o2 ...................CBN insert (Class M tolerance) .................. B032
NP-CNMAoooo ......................CBN insert (Class M tolerance) .................. B024 NP-VNMMoooR/LF .................CBN insert (Class M tolerance) .................. B056
NP-CNMAooooo ...................CBN insert (Class M tolerance) .................. B024 NP-WCGWooo-oo3 ...............CBN insert (Class G tolerance) .................. B049
NP-CNMAooo-o2 ...................CBN insert (Class M tolerance) .................. B023 NP-WCMWoooFA...................CBN insert (Class M tolerance) .................. B049
NP-CNMMoooR/LF.................CBN insert (Class M tolerance) .................. B054 NP-WCMWoooG.....................CBN insert (Class M tolerance) .................. B049
NP-CPGBooo-oo2 ................CBN insert (Class G tolerance) .................. B041 NP-WEEW13T3AGoR3C .........Wiper CBN insert
NP-CPMBoooG ......................CBN insert (Class M tolerance) .................. B041
(For ASX445 type cutter) ................J035,K011
NP-CPMHooo .........................CBN insert (Class M tolerance) .................. B058 NP-WFC42ZFERo ....................Wiper CBN insert
NP-DCGWoooo......................CBN insert (Class G tolerance) .................. B043
(For BF407 type cutter) ...................J035,K019
NP-DCGWooooo ...................CBN insert (Class G tolerance) .................. B043 NP-WNGA432-oo3 ..................CBN insert (Class G tolerance) .................. B034
NP-DCGWooo-oo2 ...............CBN insert (Class G tolerance) .................. B042 NP-WNGA432-GoWS3 ............CBN insert (Class G tolerance) .................. B034
NP-DCGWooo-o2 ..................CBN insert (Class G tolerance) .................. B042 NP-WNGA432GA......................CBN insert (Class G tolerance) .................. B034
NP-DCMToooR/LF .................CBN insert (Class M tolerance) .................. B059 NP-WNGA432-GA6 ..................CBN insert (Class G tolerance) .................. B034
NP-DCMWoooG .....................CBN insert (Class M tolerance) .................. B043 NSooo .....................................Clamp screw (For small tools holder) .........M004
VIII
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
NSoooW..................................Clamp screw (For small tools holder) .........M005 SCooMooSoooS/L...............Straight shank arbor (For Screw-in) ........... K142
NSE300Roooo .......................NSE300 type face mill ................................ K028 SCooMooSoooSW/LW ........Straight shank arbor (For Screw-in) ........... K142
NSE300RooooC/E .................NSE300 type face mill ................................ K028 SCooMooSoo-HSK63A........HSK shank arbor (For Screw-in) ................ K142
NSE400RooooC/E/F/M ..........NSE400 type face mill ................................ K028 SCooMooS10-BToo .............BT shank arbor (For Screw-in) ................... K143
SCACR/Looooooo-SM ........External front turning holder ....................... D012
SCACR/LoooSM.....................External front turning holder ....................... D008

SCLCR/L-ooo .........................Screw clamp type holder ............................ C030
OEEX1705ETR1 .......................Insert (For BOE type cutter) ...............J018,K108 SCLCR/Looooooo-SM ........External front turning holder ....................... D012
OEMXooooESR1 ...................Insert (For BOE type cutter) ...............J018,K108 SCLCR/LoooSM .....................External front turning holder ....................... D008
OEMXooooETRo ..................Insert (For BOE type cutter) ......J018,J034,K108 SCMTooo ................................Insert (Class M tolerance) ...........................A117
OEMXooooEER1-JS..............Insert (For BOE type cutter) ...............J018,K108 SCMToooFV ...........................Insert (Class M tolerance) ...........................A117
OEMXooooETR1-JS ..............Insert (For BOE type cutter) ...............J018,K108 SCMWooo...............................Insert (Class M tolerance) ...........................A117
S-DCLNR/L-ooo-C..................DOUBLE CLAMP DIMPLE BAR................. E021
S-DDUNR/L-ooo-C .................DOUBLE CLAMP DIMPLE BAR................. E021

SDEN42AEN .............................Insert (For milling)........................................ J030
PMCooRoooAMoooo.........PMC type end mill ...................................... K137 SDJCR/L-ooo .........................Screw clamp type holder ............................ C031
PMFoooooAooR ..................PMF type end mill ....................................... K140 SDJCR/Looooooo-SM.........External front turning holder ....................... D013
PMFA13R ..................................Cartridge (For PMF type cutter).................. K140 SDJCR/L-oooSM ....................External front turning holder ....................... D009
PMRooooooAooR ..............PMR type end mill ...................................... K139 SDJER/L-ooo..........................Screw clamp type holder ............................ C041
PMRooooooBR ....................PMR type end mill ...................................... K139 SDKNooAEo ...........................Insert (For milling)........................................ J030
SDNCN-ooo ............................Screw clamp type holder ............................ C031
SDNCR/Looooooo-SM ........External front turning holder ....................... D013

SDNCR/LoooSM.....................External front turning holder ....................... D009
QOGTooooR-G1 ....................Insert (For AQX type end mill) .....J013,J014,K084 S-DSKNR/L-ooo-C .................DOUBLE CLAMP DIMPLE BAR................. E022
QOMTooooR-M2....................Insert (For AQX type end mill) .....J013,J014,K084 S-DTFNR/L-ooo-C ..................DOUBLE CLAMP DIMPLE BAR................. E022
S-DVUNR/L-ooo-C .................DOUBLE CLAMP DIMPLE BAR................. E023
S-DWLNR/L-ooo-C .................DOUBLE CLAMP DIMPLE BAR................. E023

SDXCR/L-ooo .........................Screw clamp type holder ............................ C032
RBGoo .....................................Insert (Class G tolerance)........................... B050 SECNooAFoN1.......................Insert

RBHoooooA ..........................Holder (For MICRO-DEX/MICRO-MINI) ..... E034
(For SE445/545 type face mill) ....... J024,J025
RBHooooN .............................Holder (For MICRO-DEX/MICRO-MINI) ..... E036 SECN42AFFR1 .........................Insert (For SE445 type face mill) ................. J034
RCGTooooM0-AZ ..................Insert (Class G tolerance)........................... A115 SECN42EFoR/L1 .....................Insert (For SE415 type face mill) ................. J024
RCMTooooM0 ........................Insert (Class M tolerance) .......................... A115 SEENooAFoNo ......................Insert
RCMXooooM0........................Insert (Class M tolerance) .......................... A115
(For SE445/545 type face mill) ....... J024,J025
RCMXooooM0-RBS ...............Insert (Class M tolerance) .......................... A115 SEEN42EFoR/L1 .....................Insert (For SE415 type face mill) ................. J024
RCMXooooM0-RR .................Insert (Class M tolerance) .......................... A115 SEEN53EFoR1 .........................Insert (For SE515 type face mill) ................. J025
RDMWooooM0E ....................Insert (For ARX type end mill) ............J014,K100 SEERooAFEN-JS....................Insert (For SE445/545 type cutter) .............. J025
REMXoooooN .......................Insert (For BOE type cutter) ...............J019,K108 SEER42EFER-JS......................Insert (For SE415 type cutter) ..................... J024
REMXoooooN-JS ..................Insert (For BOE type cutter) ...............J019,K108 SEER43AFEN-JS .....................Insert (For milling)........................................ J031
RGEN2004oN ...........................Insert (For milling)........................................ J026 SEET13T3AGoN-JL .................Insert (For ASX445 type face mill) ......J015,K011
RGGM2004M0 ..........................Insert (Class G tolerance)........................... A116 SEGT13T3AGFN-JP .................Insert (For ASX445 type face mill) ......J016,K011
RNGoo .....................................Insert (Class G tolerance)........................... B036 SEKNooAFoN.........................Insert (For SE445/545 type cutter) ..... J024,J025
RNMAoo ..................................Insert (Class M tolerance) .......................... A079 SEKNooAFoN1.......................Insert (For SE445/545 type cutter) ..... J024,J025
RNMGoo ..................................Insert (Class M tolerance) .......................... A079 SEKN42AGTN ..........................Insert (For milling)........................................ J031
RPMTooooooE-JS ...............Insert (For BRP type cutter)................J019,K105 SEKN42EFoR ..........................Insert (For SE415 type face mill) ................. J024
RPMWooooooE....................Insert (For BRP type cutter)................J019,K105 SEKN42EFoR1 ........................Insert (For SE415 type face mill) ................. J024
RSooooT/TS ..........................Clamp screw ...............................................M005 SEMN43AZEN ..........................Insert (For milling)........................................ J031
RTGooA...................................Insert (Class G tolerance)........ A137,B050,C045 SEMT13T3AGSN-FT ................Insert (For ASX445 type face mill) ......J015,K011
SEMT13T3AGSN-JH ................Insert (For ASX445 type face mill) ......J015,K011
SEMT13T3AGSN-JM ................Insert (For ASX445 type face mill) ......J015,K011

SETK51 .....................................Clamp bridge ..............................................M014
So .............................................Clamp screw ...............................................M005 SETSo1 ....................................Clamp screw ...............................................M005

Soo ..........................................Clamp screw ...............................................M005 SFAN42ZFFR/L2.......................Insert (For BF407 type face mill) ........J018,K019
Soo-STHNR/L-o......................Grooving and threading boring bar ....F161,G035 SFCN42ZFFR2..........................Insert (For BF407 type face mill) ................. J018
Soo-STHOR/L-o .....................Grooving and threading boring bar ....F161,G035
J034,K019
SBAHRoooo ..........................Boring holder .............................................. D047 S-FSCLPR/L-ooo-C ................Screw clamp DIMPLE BAR ........................ E006
SBATooooooL ......................Insert (For BAHR type holder) .................... D047 S-FSTUPR/L-ooo-C ................Screw clamp DIMPLE BAR ........................ E007
SBATooooooL-B ..................Insert (For BAHR type holder) .................... D047 SHooo-FSDUCLoo ...............DIMPLE SLEEBE holder ...................D039,D040
SBHooooR .............................Holder (For MICRO-DEX/MICRO-MINI) ..... E037 SLoooo-90 .............................HSK boring bar sleeve................................ H022
IX
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
SLCS105 ...................................Clamp screw ...............................................M005 SPSCN42 ..................................Shim ........................................................... M011

SL-ONEN120404ASN ...............Insert (For AOX445 type cutter)..........J034,K017 SPSDN32 ..................................Shim ........................................................... M011
S-MCLNR/L-ooo .....................Multiple clamp type holder .......................... E024 SPSSN42 ..................................Shim ........................................................... M011
S-MDUNR/L-ooo.....................Multiple clamp type holder .......................... E024 SPSTN32...................................Shim ........................................................... M011
S-MSKNR/L-ooo .....................Multiple clamp type holder .......................... E025 SPSVNoo.................................Shim ........................................................... M011
S-MTFNR/L-ooo .....................Multiple clamp type holder .......................... E025 SPX4-oooA24A058RA ...........SPX type end mill (Metric type) .................. K071
S-MTFNR/L-oooX ...................Multiple clamp type holder .......................... E025 SPX4RooooooA058A ..........SPX type end mill (Metric type) .................. K071
S-MVUNR/L-ooo .....................Multiple clamp type holder .......................... E026 SPX4R050ooWNo ..................SPX type end mill ....................................... K070
S-MWLNR/L-ooo ....................Multiple clamp type holder .......................... E026 SPX4R32ooCAT50No ............SPX type end mill ....................................... K070
SNGooo ..................................Insert (Class G tolerance).........A099,B036,B057 SPX4URooooA22A................SPX type end mill ....................................... K070
SNGAooo................................Insert (Class G tolerance).........A084,B029,B055 SRDCN-ooooM ......................Screw clamp type holder ............................ C033
SNGGoooPK ..........................Insert (Class G tolerance)........................... A080 SRDPN-1612 .............................Screw clamp type holder ............................ C040
SNGGoooR/L..........................Insert (Class G tolerance)........................... A082 SRDPR/L-1612..........................Screw clamp type holder ............................ C040
SNMAooo ...............................Insert (Class M tolerance) .......................... A084 SRFHooAMoooo ..................SRF type end mill (Metric type) .................. K120
SNMGooo ...............................Insert (Class M tolerance) .......................... A082 SRFHooSooo ........................SRF type end mill (Metric type) ..........K117,K118
SNMGoooC.............................Insert (Class M tolerance) .......................... A081 SRFHooSooLW/MW ..............SRF type end mill (Metric type) ...................K119
SNMGoooFH ..........................Insert (Class M tolerance) .......................... A080 SRFToo ...................................Insert (For SRF type end mill) ............J027,K121
SNMGoooFS...........................Insert (Class M tolerance) .......................... A080 SRFToooo ..............................Insert (For SRF type end mill) ............J027,K121
SNMGoooFY...........................Insert (Class M tolerance) .......................... A080 SRFTooRoo ...........................Insert (For SRF type end mill) ............J027,K121
SNMGoooGH ..........................Insert (Class M tolerance) .......................... A083 SRFUooSooL/M .....................SRF type end mill ........................................K115
SNMGoooHAS........................Insert (Class M tolerance) .......................... A083 SRFUooSooLW/MW ..............SRF type end mill ........................................K116
SNMGoooMA..........................Insert (Class M tolerance) .......................... A081 SRGooC/E ...............................SRM2 type end mill ...................J028,J029,K134
SNMGoooMH..........................Insert (Class M tolerance) .......................... A081 SRGCR/L-ooooM ...................Screw clamp type holder ............................ C033
SNMGoooMP ..........................Insert (Class M tolerance) .......................... A081 SRK1R ......................................Clamp bridge ..............................................M014
SNMGoooMS ..........................Insert (Class M tolerance) .......................... A082 SRMoooC/E ............................Insert (For SRM2 type end mill)................... J027
SNMGoooR/L1G.....................Insert (Class M tolerance) .......................... A081
J028,K129
SNMGoooSA ..........................Insert (Class M tolerance) .......................... A080 SRMoooC/E-M ........................Insert (For SRM2 type end mill)..........J028,K129
SNMGoooSH ..........................Insert (Class M tolerance) .......................... A080 SRMooC/E-M...........................Insert (For SRM2 type end mill)..........J028,K131
SNMGoooSY ..........................Insert (Class M tolerance) .......................... A081 SRM2oooSAS2/M2/L2/L4 ......SRM2 type end mill .................................... K128
SNMMoooHV ..........................Insert (Class M tolerance) .......................... A083 SRM2oooSNLS/M ..................SRM2 type end mill .................................... K134
SNMMoooHX ..........................Insert (Class M tolerance) .......................... A083 SRM2oooWNLL/S/M/X ...........SRM2 type end mill .................................... K134
SNMMoooHXD .......................Insert (Class M tolerance) .......................... A083 SRM2ooAMooSoo ...............SRM2 type screw-in end mill ...................... K130
SNMMoooHZ ..........................Insert (Class M tolerance) .......................... A083 SRM2500MNLS/M ....................SRM2 type end mill .................................... K134
SNMNooo ...............................Insert (Class M tolerance) ..................A099,J031 SRS5 .........................................Clamp screw (For SRE type cutter) ............M005
SOET12T308PEER-JL .............Insert (For ASX400 type face mill) ......J014,K023 SRSGN-ooooM ......................Screw clamp type holder ............................ C044
SOGT12T308PEFR-JP .............Insert (For ASX400 type face mill) ......J015,K023 SRSGR/L-ooooM ...................Screw clamp type holder ............................ C044
SOMT12T308PEER/L-JM .........Insert (For ASX400 type face mill) ......J014,K023 SSBCR/L-ooo .........................Screw clamp type holder ............................ C034
SOMT12T308PEER-JH ............Insert (For ASX400 type face mill) ......J014,K023 S-SCLCR/L-ooo......................Screw clamp type boring bar ...................... E012
SOMT12T320PEER-FT.............Insert (For ASX400 type face mill) ......J015,K023 S-SDQCR/L-ooo .....................Screw clamp type boring bar ...................... E013
SONX1206PDR .........................Insert (For VOX400 type face mill) .....J030,K021 S-SDUCR/L-ooo .....................Screw clamp type boring bar ...................... E014
SPEN42EEER/L1 ......................Insert (For FBP415 type face mill) ......J020,K018 S-SL5NRooo...........................Grooving and threading boring bar ....F163,G037
SPEN42EETR1 .........................Insert (For FBP415 type face mill) ............... J034 SSSCR/L-ooo .........................Screw clamp type holder ............................ C034
SPER42EEER-JS .....................Insert (For FBP415 type cutter) ..........J020,K018 S-SSKCR/L-ooo .....................Screw clamp type boring bar ...................... E015
SPGooo ..................................Insert (Class G tolerance).........A139,B051,B067 S-STFER/L-ooo ......................AL type boring bar ...................................... E028
SPGR321R/L.............................Insert (Class G tolerance)........................... A138 S-STUCR/L-ooo......................Screw clamp type boring bar ...................... E015
SPGXooo ................................Insert (Class G tolerance).................. A118,B059 S-SVQCR/L-ooo .....................Screw clamp type boring bar ...................... E016
SPKNooEDR ...........................Insert (For milling)........................................ J030 S-SVUCR/L-ooo .....................Screw clamp type boring bar ...................... E017
SPMB1204APT .........................Insert (For BSP type end mill) ............J019,K112 S-SWUCR/L-ooo ....................Screw clamp type boring bar ...................... E019
SPMM432A ...............................Insert (For TBE2 type end mill).................... J029 STASXoooN............................Shim (For ASX445/400 type face mill) .......M012
SPMNooo................................Insert (Class M tolerance) ..................A138,J031 STAWoNooooSoo ...............STAW type drill (Metric type) .......................L094
SPMNooo-CH .........................Insert (For milling)........................................ J031 STAWNooooTH......................Insert (For STAW type drill) .........................L095
SPMNoooT .............................Insert (For TBE2 type end mill).................... J031 STFCR/L-ooo..........................Screw clamp type holder ............................ C035
SPMRooo................................Insert (Class M tolerance) .......................... A138 STFER/L-ooo ..........................AL type holder ............................................ C042
SPMTooo ................................Insert (Class M tolerance) ...........................A118 STGCR/L-ooo .........................Screw clamp type holder ............................ C035
SPMWooo ...............................Insert (For CFSP type end mill) ...................A118 STGER/L-ooo .........................AL type holder ............................................ C042
J020,K114 SVHBR/L-ooo .........................Screw clamp type holder ............................ C029
SPMX120408-JM ......................Insert (For SPX type end mill) ............J026,K072 SVJBR/L-ooo..........................Screw clamp type holder ............................ C028
SPMX120408-WH .....................Insert (For SPX type end mill) ............J027,K072 SVJBR/Looooooo-SM .........External front turning holder ....................... D014
SPNN42EEER/L1......................Insert (For FBP415 type face mill) ......J021,K018 SVJBR/LoooSM .....................External front turning holder ....................... D010
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
SVJCR/L-ooo..........................Screw clamp type holder ............................ C036 TNGGoooPK...........................Insert (Class G tolerance)........................... A085
SVJDR/L-ooo..........................AL type holder ............................................ C043 TNGGoooR/L ..........................Insert (Class G tolerance)........................... A089
SVLPR/Looooooo-SM .........External front turning holder ....................... D014 TNGGoooR/LF........................Insert (Class G tolerance)........................... A085
SVLPR/LoooSM .....................External front turning holder ....................... D010 TNGGoooR/LFS .....................Insert (Class G tolerance)........................... A085
SVPCR/L-ooo .........................Screw clamp type holder ............................ C036 TNGGoooR/LK .......................Insert (Class G tolerance)........................... A087
SVPDR/L-ooo .........................Screw clamp type holder ............................ C043 TNMAooo................................Insert (Class M tolerance) .......................... A091
SVPPR/Looooooo-SM.........External front turning holder ....................... D015 TNMCooNGR/Looo ...............Grooving insert ...............F160,F161,G034,G035
SVVBN-ooo ............................Screw clamp type holder ............................ C028 TNMCooNV .............................Threading insert..............F160,F161,G034,G035
SVVBR/Looooooo-SM ........External front turning holder ....................... D015 TNMGooo ...............................Insert (Class M tolerance) .......................... A088
SVVBR/LoooSM .....................External front turning holder ....................... D011 TNMGoooC .............................Insert (Class M tolerance) .......................... A086
SWLCR/L-ooo ........................Screw clamp type holder ............................ C037 TNMGoooFH...........................Insert (Class M tolerance) .......................... A085
SXZCR/L-ooo .........................Double clamp type holder ........................... C038 TNMGoooFS ...........................Insert (Class M tolerance) .......................... A085
SXZCR/L-ooooo15 ................Double clamp type holder (Inch type) ......... C038 TNMGoooFY ...........................Insert (Class M tolerance) .......................... A085
TNMGoooGH ..........................Insert (Class M tolerance) .......................... A090
TNMGoooMA ..........................Insert (Class M tolerance) .......................... A087

TNMGoooMH ..........................Insert (Class M tolerance) .......................... A087
TAFL/M/Soooo.......................TAF type drill (Inch type) ..................L120 L122 TNMGoooMJ ..........................Insert (Class M tolerance) .......................... A087
TAFL/M/SooooFoo...............TAF type drill (Metric type) ...............L123 L126 TNMGoooMP ..........................Insert (Class M tolerance) .......................... A087
TAWoooR-90 ..........................Chamfer Ring ..............................................L118 TNMGoooMS ..........................Insert (Class M tolerance) .......................... A088
TAWC12T301-45GM.................Insert (For Chamfer ring) .............................L119 TNMGoooR/L1G .....................Insert (Class M tolerance) .......................... A087
TAWKHooooTG .....................Insert (For TAW type drill) ..................L114,L115 TNMGoooR/L1M.....................Insert (Class M tolerance) .......................... A086
TAWLN/MN/SNoooo..............TAW type drill (Inch type) .................L098 L103 TNMGoooR/L2G .....................Insert (Class M tolerance) .......................... A089
TAWLN/MN/SNooooSoo .....TAW type drill (Metric type) ..............L106 L110 TNMGoooR/L2M.....................Insert (Class M tolerance) .......................... A089
TAWNooooT ..........................Insert (For TAW type drill) .........L104,L116,L117 TNMGoooR/LES .....................Insert (Class M tolerance) .......................... A089
TAWNHooooT........................Insert (For TAW type drill) .........L105,L112,L113 TNMGoooSA ..........................Insert (Class M tolerance) .......................... A086
TBGooo ..................................Insert (Class G tolerance)........................... B052 TNMGoooSH ..........................Insert (Class M tolerance) .......................... A086
TCGooo ..................................Insert (Class G tolerance)........................... A140 TNMGoooSY...........................Insert (Class M tolerance) .......................... A086
TCGToooAZ ...........................Insert (Class G tolerance)........................... A119 TNMMoooHV ..........................Insert (Class M tolerance) .......................... A090
TCGToooFJ ............................Insert (Class G tolerance)........................... A119 TNMMoooHZ ..........................Insert (Class M tolerance) .......................... A090
TCGToooFJ-P ........................Insert (Class G tolerance)........................... A119 TNMNooo................................Insert (Class M tolerance) .......................... A100
TCGToooMJ ...........................Insert (Class G tolerance)........................... A120 TNMXoooMW .........................Insert (Class M tolerance) .......................... A088
TCGToooMJ-P........................Insert (Class G tolerance)........................... A120 TNMXoooSW ..........................Insert (Class M tolerance) .......................... A086
TCGToooR/LF ........................Insert (Class G tolerance)........................... A119 TNP-CCGWooo-G2 ................CBN insert (Class G tolerance) .................. B039
TCGWooo ...............................Insert (Class G tolerance)........................... B060 TNP-CCGWooo-GS2 ..............CBN insert (Class G tolerance) .................. B039
TCMTooo ................................Insert (Class M tolerance) .......................... A120 TNP-CNGAooo-oo2 ..............CBN insert (Class G tolerance) .................. B023
TCMToooFV ...........................Insert (Class M tolerance) .......................... A119 TNP-CNGAooo-o2 .................CBN insert (Class G tolerance) .................. B023
TCMWooo ...............................Insert (Class M tolerance) ........A120,B044,B060 TNP-CNMAooo-o2 .................CBN insert (Class M tolerance) .................. B023
TECN32PEoR1W .....................Insert (For NSE300 type face mill) .....J022,K029 TNP-DCGWooo-G2 ................CBN insert (Class G tolerance) .................. B042
TECN43PEoR1 ........................Insert (For NSE400 type face mill) .....J023,K029 TNP-DNGAooo-oo2 ..............CBN insert (Class G tolerance) .................. B026
TEENooPEoR1 .......................Insert (For NSE300/400 type face mill) ....... J023 TNP-DNGAooo-o2 .................CBN insert (Class G tolerance) .................. B026
J024,K029 TNP-DNMAooo-G2 .................CBN insert (Class M tolerance) .................. B026
TEERooPEER-JS ....................Insert
TNP-SNGAooo-o2 .................CBN insert (Class G tolerance) .................. B028
(For NSE300/400 type face mill) .....J023,K029 TNP-TNGAooo-o3 .................CBN insert (Class G tolerance) .................. B031
TEGXooo ................................Insert (Class G tolerance)........................... B065 TNP-VNGAooo-oo2 ..............CBN insert (Class G tolerance) .................. B032
TEGXoooR/L ..........................Insert (Class G tolerance).................. A121,B065 TNP-VNGAooo-o2 .................CBN insert (Class G tolerance) .................. B032
TEKN43PEoR ..........................Insert (For NSE400 type face mill) .....J023,K029 TNP-VNMAooo-o2 .................CBN insert (Class M tolerance) .................. B032
TEKN43PEoR1 ........................Insert (For NSE400 type face mill) .....J023,K029 TPEW1303ZPoR2 ....................Insert (For PMF type end mill) .....J023,J034,K140
TKYooD ...................................Driver wrench .............................................M002 TPGooo...................................Insert (Class G tolerance).........A142,B053,B067
TKYooF ...................................Flag wrench ................................................M002 TPGHoooR/LFS......................Insert (Class G tolerance)........................... A122
TKYooL ...................................Long L-wrench ............................................M002 TPGRoooR/L ..........................Insert (Class G tolerance)........................... A141
TKYooR ...................................L-wrench .....................................................M002 TPGToooR/LF ........................Insert (Class G tolerance)........................... B061
TKYooT ...................................T-wrench.....................................................M002 TPGVoooR/LF ........................Insert (Class G tolerance)........................... B062
TKYooW ..................................Flag wrench ................................................M002 TPGXooo ................................Insert (Class G tolerance).........A124,B046,B062
TLHN-ooo ...............................TL holder .................................................... C045 TPGXoooR/L ..........................Insert (Class G tolerance)........................... A123
TLHN-oooo ............................TL holder .................................................... C045 TPKNooPoR/L ........................Insert (For milling)........................................ J030
TLHR/L-ooo ............................TL holder .................................................... C045 TPMHoooFV ...........................Insert (Class M tolerance) .......................... A122
TLHR/Loooo ..........................TL holder .................................................... C045 TPMHoooMV ..........................Insert (Class M tolerance) .......................... A124
TNGooo ..................................Insert (Class G tolerance).................. A100,B037 TPMHoooSV ...........................Insert (Class M tolerance) .......................... A123
TNGAooo ................................Insert (Class G tolerance).........A091,B031,B055 TPMNooo ................................Insert (Class M tolerance) ..................A141,J032
XI
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
TPMRooo ................................Insert (Class M tolerance) .......................... A141 VCMToooSV ...........................Insert (Class M tolerance) .......................... A128
TPMToooMQ ..........................Insert (Class M tolerance) .......................... A124 VCMWooo...............................Insert (Class M tolerance) .......................... A129
TPMToooSQ ...........................Insert (Class M tolerance) .......................... A123 VCPSRB....................................MIRACLE end mill (Metric type) ...................I125
TPMXooo ................................Insert (Class M tolerance) .......................... A124 VCSFPR ....................................MIRACLE end mill (Metric type) ...................I117
TPMXoooL ..............................Insert (Class M tolerance) .......................... A123 VCXB.........................................MIRACLE end mill (Metric type) ...................I121
TPSoo ......................................Clamp screw ...............................................M005 VDGXoooR/L ..........................Insert (Class G tolerance).................. A130,B066
TPSoo-o ..................................Clamp screw ...............................................M005 VF2MV.......................................IMPACT MIRACLE end mill (Metric type).....I140
TRM4ooW32S/M .....................TRM4 type end mill..................................... K136 VF2SB .......................................IMPACT MIRACLE end mill (Metric type).....I156
TSo ...........................................Clamp screw ...............................................M006 VF2SDB ....................................IMPACT MIRACLE end mill (Metric type).....I157
TSoo ........................................Clamp screw ...............................................M006 VF2SDBL ..................................IMPACT MIRACLE end mill (Metric type).....I158
TSooo .....................................Clamp screw ...............................................M006 VF2SSB.....................................IMPACT MIRACLE end mill (Metric type).....I155
TSS04005..................................Radial screw ...............................................M006 VF2WB ......................................IMPACT MIRACLE end mill (Metric type).....I154
TTAHR/L-ooo .........................External threading holder ........................... D035 VF2XL .......................................IMPACT MIRACLE end mill (Metric type).....I138
TTAHR/Loooo ........................External threading holder ........................... D036 VF2XLB .....................................IMPACT MIRACLE end mill (Metric type).....I160
TTAToooooooR/Lo-B .........Threading insert.................................D035,D036 VF2XLBS ..................................IMPACT MIRACLE end mill (Metric type).....I159
VF3XB .......................................IMPACT MIRACLE end mill (Metric type).....I165
VF4MB ......................................IMPACT MIRACLE end mill (Metric type).....I168

VF4MV.......................................IMPACT MIRACLE end mill (Metric type).....I141
UDKoo .....................................Insert (For TBE1 type end mill).................... J029 VF4SVB.....................................IMPACT MIRACLE end mill (Metric type).....I169
UDK50Ao .................................Insert (For TBE2 type end mill).................... J029 VF6MHV ....................................IMPACT MIRACLE end mill (Metric type).....I145
UGHNooo ...............................UG holder ....................................................F158 VF6MHVCH ...............................IMPACT MIRACLE end mill (Metric type).....I146
UPMoo .....................................Insert (For TRM4 type end mill) ..........J029,K136 VF6MHVRB ...............................IMPACT MIRACLE end mill (Metric type).....I175
UPMooPo................................Insert (For TRM4 type end mill) ..........J030,K136 VF6MHVRBCH..........................IMPACT MIRACLE end mill (Metric type).....I176
VF6SVRCH ...............................IMPACT MIRACLE end mill (Metric type).....I152
VF8MHVCH ...............................IMPACT MIRACLE end mill (Metric type).....I147

VF8MHVRBCH..........................IMPACT MIRACLE end mill (Metric type).....I177
VBEToooR/LSN......................Insert (Class E tolerance) ........................... A127 VFHVRB ....................................IMPACT MIRACLE end mill (Metric type).....I170
VBEToooR/LSR......................Insert (Class E tolerance) ........................... A126 VFHVRB ....................................IMPACT MIRACLE end mill (Inch type)........I172
VBEToooR/LWSN ..................Insert (Class E tolerance) ........................... A127 VFJHV .......................................IMPACT MIRACLE end mill (Metric type).....I144
VBGToooFJ ............................Insert (Class G tolerance)........................... A125 VFMD ........................................IMPACT MIRACLE end mill (Metric type).....I149
VBGToooFJ-P ........................Insert (Class G tolerance)........................... A125 VFMFPR ....................................IMPACT MIRACLE end mill (Metric type).....I153
VBGToooMJ ...........................Insert (Class G tolerance)........................... A126 VFMHV ......................................IMPACT MIRACLE end mill (Metric type).....I142
VBGToooMJ-P .......................Insert (Class G tolerance)........................... A126 VFMHVCH .................................IMPACT MIRACLE end mill (Metric type).....I143
VBGToooR/LF ........................Insert (Class G tolerance)........................... A125 VFMHVRB .................................IMPACT MIRACLE end mill (Metric type).....I173
VBMTooo ................................Insert (Class M tolerance) .......................... A126 VFMHVRBCH............................IMPACT MIRACLE end mill (Metric type).....I174
VBMToooFV ...........................Insert (Class M tolerance) .......................... A125 VFSD .........................................IMPACT MIRACLE end mill (Metric type).....I148
VBMToooMV ..........................Insert (Class M tolerance) .......................... A126 VFSFPR ....................................IMPACT MIRACLE end mill (Metric type).....I150
VBMToooSV ...........................Insert (Class M tolerance) .......................... A125 VFSFPRCH ...............................IMPACT MIRACLE end mill (Metric type).....I151
VC2C .........................................MIRACLE end mill (Metric type) ...................I137 VFX6-oooAooAoooR ..........VFX6 type end mill (Metric type) ................ K076
VC2ESB ....................................MIRACLE end mill (Metric type) ...................I118 VNGAooo................................Insert (Class G tolerance).........A093,B033,B056
VC2PSB ....................................MIRACLE end mill (Metric type) ...................I119 VNGGoooFJ ...........................Insert (Class G tolerance)........................... A092
VC2PSBP ..................................MIRACLE end mill (Metric type) ...................I120 VNGGoooR/L..........................Insert (Class G tolerance)........................... A093
VC3MB ......................................MIRACLE end mill (Metric type) ...................I123 VNGGoooR/LF .......................Insert (Class G tolerance)........................... A092
VC4JRB ....................................MIRACLE end mill (Metric type) ...................I129 VNGMoooMJ ..........................Insert (Class G tolerance)........................... A093
VC4MB ......................................MIRACLE end mill (Metric type) ...................I124 VNMGooo ...............................Insert (Class M tolerance) .......................... A093
VC4STB ....................................MIRACLE end mill (Metric type) ...................I135 VNMGoooFH ..........................Insert (Class M tolerance) .......................... A092
VC6MH ......................................MIRACLE end mill (Metric type) ...................I115 VNMGoooFS...........................Insert (Class M tolerance) .......................... A092
VC8MH ......................................MIRACLE end mill (Metric type) ...................I116 VNMGoooMA..........................Insert (Class M tolerance) .......................... A093
VCGToooAZ ...........................Insert (Class G tolerance)........................... A128 VNMGoooMH..........................Insert (Class M tolerance) .......................... A093
VCGToooR/LF ........................Insert (Class G tolerance)........................... A128 VNMGoooMJ ..........................Insert (Class M tolerance) .......................... A092
VCHFRB....................................MIRACLE end mill (Inch type) ......................I132 VNMGoooMP ..........................Insert (Class M tolerance) .......................... A093
VCHFRB....................................MIRACLE end mill (Metric type) ...................I130 VNMGoooMS ..........................Insert (Class M tolerance) .......................... A093
VCLD .........................................MIRACLE end mill (Metric type) ...................I113 VNMGoooSH ..........................Insert (Class M tolerance) .......................... A092
VCMDSC ...................................MIRACLE end mill (Metric type) ...................I112 VOX400-oooAooR ................vox400 type face mill (Metric type) .... K020,K021
VCMH ........................................MIRACLE end mill (Metric type) ...................I114 VOX400Roooooo .................vox400 type face mill (Metric type) ............. K020
VCMHDRB ................................MIRACLE end mill (Metric type) ...................I133 VPEToooR/LARF ...................Insert (Class E tolerance) ........................... A131
VCMTooo ................................Insert (Class M tolerance) .......................... A128 VPGToooSMGF ......................Insert (Class G tolerance)........................... A131
VCMToooFV ...........................Insert (Class M tolerance) .......................... A128
VCMToooMV ..........................Insert (Class M tolerance) .......................... A128
XII
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
WBGToooR/LF .......................Insert (Class G tolerance)........................... A132 XCMToooSVX.........................Insert (Class M tolerance) .......................... A136
WBMToooR/LMV....................Insert (Class M tolerance) .......................... A132 XDGT1550PDoR-Goo ............Insert (For BXD4000 type cutter)................. J019
WCGToooFJ ...........................Insert (Class G tolerance)........................... A133
J020,K062
WCGToooFJ-P .......................Insert (Class G tolerance)........................... A133 XDGT1550PDoR-GLoo ..........Insert (For BXD4000 type cutter)........J020,K062
WCGToooMJ ..........................Insert (Class G tolerance)........................... A133 XDGX1750ooPDFR-GL...........Insert (For AXD4000 type cutter)........J016,K053
WCGToooMJ-P ......................Insert (Class G tolerance)........................... A133 XDGX2270ooPDFR-GL...........Insert (For AXD7000 type cutter)........J016,K059
WCGToooR/L .........................Insert (Class G tolerance)........................... A133 XNMU190912R-MS ...................Insert (For VFX6 type end mill)...........J030,K076
WCMTooo ...............................Insert (Class M tolerance) .......................... A134 XNSoo .....................................Clamp screw ...............................................M007
WCMWooo..............................Insert (Class M tolerance) .......................... B064 XNSooo...................................Clamp screw ...............................................M007
WCS503507H............................Shim screw .................................................M007 XPGT13T3PDoR-Go ...............Insert (For BAP3500 type cutter) ........J018,K051
WECooAFoR5C......................Wiper insert (For SE445/545 type face mill) ........ XPMT13T3PDER-Mo ...............Insert (For BAP3500 type cutter) ........J018,K051
J025,J026,J035
WEC400PEER10C ....................Wiper insert (For SE400 type face mill) ....... J024
WEC42AFER10C ......................Wiper insert (For SE445 type face mill) ....... J025
WEC42EFoR5C .......................Wiper insert (For SE415 type face mill) ....... J024 ZCMXooooooERo ...............Insert (For LER type end mill).............J021,K078
WEC42EFER10C ......................Wiper insert (For SE415 type face mill) ....... J024
WEEW13T3AGoR8C ...............Wiper insert
(For ASX445 type face mill) ............J016,K011
WFC42ZFER2 ...........................Wiper insert (For BF407 type face mill) ....... J035
K019
WNEU2006ZEN7C-WK.............Wiper insert
(For AHX640W type face mill) ........J012,K014
WNMAooo ..............................Insert (Class M tolerance) .......................... A097
WNMGooo ..............................Insert (Class M tolerance) .......................... A096
WNMGoooC............................Insert (Class M tolerance) .......................... A095
WNMGoooFH .........................Insert (Class M tolerance) .......................... A094
WNMGoooFS..........................Insert (Class M tolerance) .......................... A094
WNMGoooFY..........................Insert (Class M tolerance) .......................... A094
WNMGoooGH .........................Insert (Class M tolerance) .......................... A096
WNMGoooGJ .........................Insert (Class M tolerance) .......................... A097
WNMGoooMA.........................Insert (Class M tolerance) .......................... A095
WNMGoooMH.........................Insert (Class M tolerance) .......................... A096
WNMGoooMJ .........................Insert (Class M tolerance) .......................... A095
WNMGoooMP .........................Insert (Class M tolerance) .......................... A095
WNMGoooMS .........................Insert (Class M tolerance) .......................... A096
WNMGoooMW ........................Insert (Class M tolerance) .......................... A096
WNMGoooSA .........................Insert (Class M tolerance) .......................... A094
WNMGoooSH .........................Insert (Class M tolerance) .......................... A094
WNMGoooSW ........................Insert (Class M tolerance) .......................... A095
WNMGoooSY .........................Insert (Class M tolerance) .......................... A095
WOEW12T308PEoR8C ...........Wiper insert
(For ASX400 type face mill) ............J015,K023
WPC42EEER/L10C...................Wiper insert
(For FBP415 type face mill) ............J021,K018
WPC42EETR10C ......................Wiper insert
(For FBP415 type face mill) ............J035,K018
WPGTooo ...............................Insert (Class G tolerance).................. A135,B064
WPGToooR/LFS .....................Insert (Class G tolerance)........................... A135
WPMToooMV..........................Insert (Class M tolerance) .......................... A135
WSooLH ..................................Stopper (For STAW type drill) .....................L097
WSooooooT .........................Clamp screw (For TAW type drill)...............M007
WSooooooTPS.....................Internal screw (For STAW type drill)............L097
XIII
SAFETY OF CUTTING TOOL PRODUCTS

y 1. Use of Cutting Tool Products
Packages of Mitsubishi products carry a safety warning label. However, tools are not labeled with detailed warning
instructions. Please read the "Safety of Cutting Tool Products" in this catalog before handling cutting tool products
and cemented carbide materials. Moreover, as a part of your workers' safety education, please notify the contents
of the "Safety of Cutting Tool Products" to all workers.
y 2. Basic Characteristics of Hard Tool Materials

aIn Terms of "Safety of Cutting Tool Products"
Hard Tool Materials : General term for tool materials like cemented carbide alloy, cermet, ceramics,
sintered CBN, sintered diamond, high speed steel and alloy steel, etc.
aPhysical Characteristics
Appearance : Varies depending on the type of material, e.g. gray, black, gold, etc.
Smell
: None
Hardness, Specic Gravity :
Hard Tool Materials
Hardness (HV)
Specic Gravity
High Speed Steel (HSS)
200 1200kg/mm2
79
Cemented Carbide
500 3000kg/mm
9 16
Sintered Diamond
Cermet
500 3000kg/mm2
59
Alloy Steel
1000 4000kg/mm
27
Diamond Electroforming Product 8000 12000kg/mm
Ceramics
Hard Tool Materials

Sintered CBN
Hardness (HV)
Specic Gravity
2000 5000kg/mm2
35
8000 12000kg/mm
35
200 1200kg/mm2
79
35
aConstituents
Carbide, nitride, carbon nitride, oxide, W, Ti, Al, Si, Ta, B, V and metals such as Fe, Co, Ni, Cr, Mo.
y 3. Safety of Cutting Tool Products

uHard tool materials have a large specic gravity. Thus, they require special attention as heavy materials when
the size or quantity is large.

uHard tool materials generates dust and mist during grinding operations or heating. This dust and mist can be harmful to the
human body when coming in contact with the eyes or skin, or if substantial quantities are swallowed. When grinding and
machining, it is recommended to use local exhaust ventilation and respirators, a dust protective mask, glasses, gloves and so
on. If dust makes contact with the hands, thoroughly wash the affected area with soap and water. Don't eat in the exposed
area, and wash hands thoroughly before eating. Remove dust from the clothing by a cleaner or washing, but don't shake off.
uCobalt dust can affect the skin, respiratory organs and heart through repeated or prolonged contact.
uFor further information, please refer to MSDS (Material Safety Data Sheet).
Home page: http://www.mitsubishicarbide.com/msds/
y 4. Handling Cutting Tool Products

uSurface conditions affect toughness of cutting tools. Therefore, use a diamond grinding wheel for nishing.
uHard tool materials are extremely hard and brittle at the same time. Thus, they may be broken by shock and
tightening with excess force.

uHard tool materials and ferrous materials have different thermal expansion ratios. Shrinkage or swell t products
may suffer from cracks when applied temperature is higher or lower than the appropriate temperature for the tool.
uPay special attention regarding storing hard tool materials. Toughness of hard tool materials is lowered when
they corrode due to coolant and other liquid.

uWhen brazing hard tool materials, if the temperature is too high or too low from the melting point of the brazing
material, loosening and breakage may occur.

uAfter regrinding cutting tools, make sure that there are no cracks.
uMachining hard tool materials on EDM may cause cracks on the surface due to remaining electrons resulting in
lowering the toughness. Eliminate cracks by grinding, etc.
SUGGESTIONS ON HOW TO USE CUTTING TOOLS

Hazard
Products
All Cutting Tools
eCutting tools have sharp cutting edges. Handling
them with bare hands may cause injuries.

eImproper use of tools and application of inappropriate
cutting conditions may cause the tool to break and be

discharged from the machine providing risk of injury.
eImpact load and rapid increase of cutting resistance
due to excessive wear may cause the tool to break and

be expelled from the machine providing risk of injury.
eCutting tools and workpieces become extremely hot
during cutting. Touching them with bare hands may

cause burns.
eExpelled hot chips produced in cutting produces risk
of injuries and burns.
Countermeasure
precautions such as wearing gloves especially
* Take
when handling tools and during installation.
safety guards and goggles are used.
* Ensure
to handling explanatory notes and catalogs.
* Refer
Use tools under recommended cutting conditions.
* Ensure
* Exchange tools before excessive wear occurs.
* Take precautions such as wearing gloves.

* Ensure
During swarf removal and machine cleaning ensure
* the
machine is stopped and wear gloves. Please use
tools, such as cutting nippers and cutting clippers.
eIn cutting, sparks, hot chips and heat generation
caused by tool breakage provides a risk of igniting a

re.
eUsing machines, chucks, and tools with poor balance
at high revolutions may cause tools to break providing

risk of injuries.
eHandling machined parts with burrs using bare hands
may cause injuries.
Indexable Inserts
Type Tools
eIf inserts and spare parts are not held securely, they
may become loose and be ejected producing risk of

injuries.
eClamping inserts and spare parts too tightly by using
tools such as extension pipes may cause them to

break and be scattered.
eWhen applying high cutting speed, spare parts and
inserts may be expelled due to centrifugal force.

Pay special attention on each safety guidline.
Cutters and Other

Rotating Tools
eMilling cutters have sharp edges.
Handling them with bare hands may cause injuries.

ePoor balance or off center revolving of tools may
cause vibration and chattering which could cause the

tool to break and be discharged.
Avoid using cutting tools in places where there is a

* possibility
of igniting a re.
In case of using non-water soluble oil, make sure to
* have a re prevention countermeasure.
* Ensure
Check the machine for vibration, chattering, and
* abnormal noise.
* Wear gloves.
insert locating seat and spare parts before
* Clean
setting inserts.
the tool provided for setting inserts, and ensure
* Use
the inserts and spare parts are clamped securely. Do
not use the tool provided for things other than
prescribed inserts and spare parts.
not use extra tools for more leverage.
* Do
the tool provided.
Only use
to the handling explanatory notes and

* Refer
catalogs. Use tools under recommended cutting
conditions.
* Take precautions such as wearing gloves.

cutting speed within the range of recommended
* Apply
cutting conditions.
Adjust accuracy and balance of spindles and
* bearings
periodically to prevent off center revolving
and chattering caused by wear on these parts.
Drilling Tools
eThrough cutting in cases when the workpiece
revolves may produce a disk shaped peice with sharp

edges when the cutting tool breaks through.

* Ensure
Also install a cover on the chuck.
eDrills with an extremely small diameter have a very
sharp point which may puncture the skin if not handled

carefully. If the drill breaks during cutting, the broken
parts may be scattered.
Brazed Tools
eWeakening of the braze and breakage of inserts may
cause injury.
Others
eMachine and tools may be damaged if they are used
for purposes other than the prescribed application.
Handle with care. Take precautions such as wearing

* gloves
and goggles.
Before using them, ensure they are brazed securely.
* Do
them under conditions which produce
* verynothighusetemperature.
* Use them strictly for the prescribed application.
INFORMATION
This catalog completes the basic precautions for safety use of our company's products. For further information, please refer to the guideline,
catalogs or contact us. We are not responsible for any accidents caused by modifying tools without our permission.
GUIDE TO TURNING INSERTS

Section organization
Graph of chip control by work material
zOrganized according to turning insert shape.

(Refer to the index on the next page.)
xInserts are arranged in order of :
Negative inserts (with hole|without hole)
Positive inserts (with hole|without hole)
cBreakers are arranged in order of :
Finish Cutting|Light Cutting|Medium Cutting
|Semi-Heavy Cutting|Heavy Cutting
Depicts recommended chip breakers and chip control

range according to work material and cutting application.
Graphs are colored according to cutting applications
(Finish|Light|Medium|Semi-Heavy|Heavy)
and contain recommended breakers for each application.
GRADE APPLICATION RECOMMENDED

FOR EACH WORK MATERIAL
Finish Cutting :
Light Cutting :
Semi-Heavy Cutting :
Heavy Cutting :
Medium Cutting :
FIGURE SHOWING INSERT GEOMETRY

Dimensions are detailed in the "Dimensions" column.
cutting conditions suitable for each work materials

are shown as a general guide to select grade.
Stable Cutting
General Cutting
Unstable Cutting
INDICATION OF
NEGATIVE/POSITIVE
TYPE
TITLE OF PRODUCT
ACCORDING TO THE
INSERT TYPE
SHAPE & ANGLE MARK

PRODUCT SECTION
INSERT DIMENSIONS
INSERT GRADES
STOCK STATUS
Finish Cutting
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
Light Cutting
Heavy Cutting
Semi-Heavy Cutting
Cast Iron (<350MPa)

Flat Top
Work
Material
Standard
Shape
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Stable Cutting
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
(inch)
FH
Finish
Cutting
FS
Carbide
CNMG430.5FH
431FH
432FH
433FH
CNMG120402-FH
120404-FH
120408-FH
120412-FH
.008
a a
a a
.016
a s
sa
.031
a s
sa
CNMG431FS
432FS
CNMG120404-FS
120408-FS
.016
.031
CNMG431FY
432FY
CNMG120404-FY
120408-FY
.016
.031
CNGG43V5FJ
430.2FJ
430.5FJ
431FJ
432FJ
CNGG43V5FJ-P
430.2FJ-P
430.5FJ-P
CNGG1204V5-FJ
120401-FJ
120402-FJ
120404-FJ
120408-FJ
CNGG1204V5-FJ-P
120401-FJ-P
120402-FJ-P
.002
.004
.008
.016
a s
.031
a a
CNGG431PK
432PK
CNGG120404-PK
120408-PK
.016
.031
.047
Finish
Cutting
FJ-P
RTG05A
06A
07A
08A
10A
D4
L5
.295
.295
.098
.138
.138
.138
a a
a a
.197
.236
a a
.276
.433
.138
.197
a a
a a
.315
.394
.433
.551
.177
.217
.197
.256
POSI
6
WITHOUT
HOLE
C045
ss
a s
.002
.004
.008
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008

a
r
LEGEND FOR STOCK STATUS MARK
APPLICABLE HOLDER PAGE
is shown on the left hand page of

each double-page spread.
indicates reference pages

for details of applicable holders.
CUTTING APPLICATION
PAGE REFERENCE
is shown in order of: Finish|Light

|Medium|Semi-Heavy|Heavy.
PHOTO OF INSERT
INDICATION OF CHIP BREAKER
indicates the designation for a chip breaker.
aTo
L2
C006
009
E021
E024
H006
008
Finish
Cutting
A068
Dimensions (inch)
D1
(inch)
E024
H006
008
Finish
Cutting
PK
(ISO) Number
C006
009
E021
Finish
Cutting
FJ
Order Number
C006
009
E021
E024
H006
008
Finish
Cutting
FY
Non-Ferrous Metal
Applicable
Holder Page
Unstable Cutting
(Tangent Angle)
Cast Iron
RTG05A
06A
07A
08A
10A
Cast Iron
General Cutting
Stainless Steel
Unstable Cutting
Stainless Steel
Coated
Shape
General Cutting
Steel
Stable Cutting
Steel
Feed (inch/rev)
Feed (inch/rev)
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
P
M
K
N
S
Carbide
NEG
A000
INSERTS
WITHOUT HOLE
RTG TYPE
Corner
Radius
UTi20T
HTi10
Mild Steel
FH

Depth of Cut (inch)
Size
Applicable
Holder Page
CNMG 4 3 0.5
INSERTS
WITH HOLE
CN TYPE
Depth of Cut (inch)
TURNING INSERTS
80
TURNING INSERTS
Order:
Please specify insert number and grade.
CHIP BREAKER
A066
IDENTIFICATION
A002
IDENTIFICATION
indicates reference pages, on the right hand
page of each double-page spread.
INSERT CORNER RADIUS

INSERT NUMBER
A137
TURNING
INSERT STANDARDS
INSERT GRADES
IDENTIFICATION .............................................................................................. A002
HOLE GEOMETRY ........................................................................................... A004
PRECISION BREAKER STANDARD ............................................................... A008
...................................................................................................... A013
CLASSIFICATION OF GRADES AND CHIP BREAKERS FOR TURNING ..... A014
BREAKER SYSTEMS FOR SMALL SIZE INSERTS ....................................... A026
PRECISION BREAKER SYSTEM (NEGATIVE INSERTS) .............................. A027
WIPER INSERT................................................................................................. A028
GRADES FOR TURNING ................................................................................. A030
TURNING APPLICATION RANGE ................................................................... A031
COATED CARBIDE (CVD) ............................................................................... A032
COATED CARBIDE (PVD) ............................................................................... A034
CERMET ........................................................................................................... A036
COATED CERMET ........................................................................................... A037
CEMENTED CARBIDE ..................................................................................... A038
MICRO-GRAIN CEMENTED CARBIDE ........................................................... A039
CLASSIFICATION............................................................................................. A040
STANDARD OF TURNING INSERTS
a
SCooTYPE ... SQUARE 90 .................... A117

TEooTYPE ... TRIANGULAR 60 ............ A121
VBooTYPE ... RHOMBIC 35 .................. A125
VCooTYPE ... RHOMBIC 35 .................. A128
VDooTYPE ... RHOMBIC 35 .................. A130
VP ooTYPE ... RHOMBIC 35 .................. A131
WBooTYPE... TRIGON 80...................... A132
WCooTYPE... TRIGON 80...................... A133
WPooTYPE ... TRIGON 80...................... A135
XCooTYPE ... RHOMBIC 25 .................. A136
CNooTYPE... RHOMBIC 80 .................. A068

DNooTYPE... RHOMBIC 55 .................. A074
RNooTYPE... ROUND ............................. A079
VNooTYPE ... RHOMBIC 35 .................. A092
WNooTYPE... TRIGON 80...................... A094
a
KNooTYPE... PARALLELOGRAM 55 ... A098

a
CCooTYPE... RHOMBIC 80 .................. A101

CPooTYPE ... RHOMBIC 80 .................. A107
DCooTYPE... RHOMBIC 55 .................. A109
DEooTYPE ... RHOMBIC 55 .................. A114
RCooTYPE... ROUND ............................. A115
RGooTYPE... ROUND ............................. A116
RTG TYPE ................................... A137

A001
IDENTIFICATION
Symbol
Insert Shape
Hexagonal
Octagonal
Pentagonal
Square
Triangular
Rhombic 80
Rhombic 55
Rhombic 75
Rhombic 50
Rhombic 86
Rhombic 35
Trigon
Rectangular
Parallelogram 85
Parallelogram 82
Parallelogram 55
Round
Special
Triangular insert with a facet

(Secondary Cutting Edge)
c Symbol for Tolerance Class

Tolerance of Tolerance of Detail of M Class Insert Tolerance
a Tolerance of Nose Height m (inch)
Inscribed
Thickness
Circle
Rhombic Rhombic Rhombic
S1 (inch)
I.C.
Triangular Square
&D1 (inch)
80
55
35
.0002
.001
.001
A
.250 .003 .003 .003 .004 .0063
.0002
.0005
.001
F
.375 .003 .003 .003 .004 .0063
.0005
.001
.001
C
.500 .005 .005 .005 .006
.0005
.0005
.001
H
.625 .006 .006 .006 .007
.001
.001
.001
E
.750 .006 .006 .006 .007
.001
.001
.005
.007
G
1.000
.002
.002
.005
.008
J
1.250
a Tolerance of Inscribed Circle & D1 (inch)
.0005
.002 .006
.001
K*
.001
.002 .006
.001
L*
I.C.
Triangular Square
80
55
35
.005
M * .003 .007 .002 .006
.250 .002 .002 .002 .002 .002
.001
N * .003 .007 .002 .006
.375 .002 .002 .002 .002 .002
.005
U * .005 .015 .003 .01
.500 .003 .003 .003 .003

As a rule, the sides of these inserts are as sintered.
.625 .004 .004 .004 .004

Tolerance differs with insert size. For the accuracy of
.750 .004 .004 .004 .004

class M, refer to the table on the right.
.005
1.000
.006
1.250
Symbol
TURNING INSERTS
TURNING INSERTS
Tolerance of
Nose Height
m (inch)
z Symbol for Insert Shape
Round
Round
.002
.003
.004
.004
.005
.006
c Symbol for Tolerance Class
INCH
METRIC
x Symbol for Relief Angle
Symbol
v Symbol for Chipbreaker and Clamping System

Inch
Relief Angle
Metric
.250"
Hole
I.C.
Chip
Figure I.C.
and over under .250" Symbol Hole Conguration Breaker Figure
A
B
C
D
G
N
P
O
Other Relief Angle

Major Relief Angle
A002
Special
Design
Chip
Symbol Hole ConHole
guration Breaker Figure
A
With
Hole
Cylindrical
Hole
With
Hole
Cylindrical One
Hole
Sided
With
Hole Cylindrical Hole No
+
With Double Countersink Double
Hole (40 60) Sided
With
Hole
Cylindrical Double
Sided
Hole
Without
Hole
No
With
+
One Countersink
With (70 90) One
Hole
Sided
Without
Hole
One
Sided
Without
Hole
Double
Sided
With Cylindrical Hole No

+
Hole
With Double Countersink Double
Hole (70 90) Sided
With
+
One Countersink
With (40 60) One
Hole
Sided
No
Special
Design
I.C.
under
.250"
1.2 (5)
1.5 (6)
1.8 (7)
Diameter of
Inscribed
Circle
(inch)
2
2.5
3
4
5
6
7
8
10
.156
.187
.219
.250
.313
.375
.500
.625
.750
.875
1.000
1.250
6.00mm
8.00mm
10.00mm
12.00mm
16.00mm
20.00mm
25.00mm
32.00mm
Metric
09
12
19
02
L3
03
04
05
06
08
10
13
08
09
11
13
16
22
25
31
06
08
10
12
16
20
25
32
04
05
06
07
09
11
15
19
23
27
31
38
03
04
05
06
08
09
12
16
19
22
25
32
03
04
05
06
07
09
12
15
19
22
25
31
Thickness is from the bottom of the insert

to the top of the cutting edge.
06
08
09
11
13
16
22
27
33
38
44
54
TURNING INSERTS
Inch
I.C. .250"
and over
Inch
I.C. .250"
I.C.
and over under .250"
2
2.5
3
3.5
4
5
6
Thickness
(inch)
Metric
.055
.063
.070
.078
.094
.109
.125
.156
.187
.219
.25
.313
.375
S1
01
T0
T1
02
T2
03
T3
04
05
06
07
09
0.9
1
1.1
1.2
1.5 (3)
1.8
n Symbol for Insert Thickness
b Symbol for Insert Size

/ Symbol for Chip Breaker
MP
MP
m Symbol for Insert Corner Conguration
Inch
V0
Corner Radius
(inch)
Sharp Nose
Metric
00
V3
.0012
V3
V5
.002
V5
0.2
.004
01
0.5
.008
02
.016
04
.031
08
.047
12
.063
16
.079
20
.094
24
.110
28
.126
32
00
Round Insert
M0
, Symbol for Cutting Edge Condition

Figure Cutting Edge Symbol
FH
FJ
FS
FV
FY
GH
GJ
HV
HX
HZ
MA
MH
MJ
MP
MS
MW
SA
SH
SW
. Symbol for Cutting Direction

Figure
Hand Symbol
Sharp
Cutting Edges
Right
Round
Cutting Edges
Left
Chamfered
Cutting Edges
Neutral
Chamfered
and Rounded
Cutting Edges
Standard
Mitsubishi Materials omit

the honing symbol.
A003
TURNING INSERTS
TURNING INSERTS
HOLE GEOMETRY
Type A
NEGATIVE
(ISO) Number
Insert Number
Dimension (inch)
Hole Type
D2
C N GA
CNGG
CNM A
CNMG
CNMM
CNMP
DNGA
DNGG
DNGM
DNMA
DNMG
DNMM
DNMX
32p
33p
43p
54p
64p
86p
CNGA
CNGG
CNMA
CNMG
CNMM
CNMP
33p
43p
44p
DNGA
DNGG
DNGM
DNMA
DNMG
DNMM
DNMX
32p
SNGA
SNGG
SNMA
SNMG
SNMM
TNGA
TNGG
TNMA
TNMG
TNMM
TNMX
VNGA
VNGM
VNGG
VNMG
VNMM
43p
54p
64p
SNGA
SNGG
SNMA
SNMG
SNMM
A004
0904pp
.150
1204pp
.203
1606pp
.250
1906pp
.312
2509pp
.359
1104pp
.150
1504pp
.203
1506pp
.203
0903pp
.150
1204pp
.203
1506pp
.250
.312
2507pp
.359
86p
2509pp
.359
22p
1103pp
.089
1603pp
.150
32p
33p
43p
54p
66p
33p
TNGA
TNGG
TNMA
TNMG
TNMM
TNMX
VNGA
VNGM
VNGG
VNMG
VNMM
32.5p
33p
WNMA
WNMG
43p
RNMG
RNMA
.150
1906pp
85p
32p
WNMA
WNMG
0903pp
1604pp
.150
2204pp
.203
2706pp
.250
3309pp
.312
1604pp
.150
0603pp
.150
06T3pp
.150
0604pp
.150
0804pp
.203
32
090300
.150
43
120400
.203
64
RNMG
RNMA
190600
.312
86
250900
.359
106
310900
.500
Type C
Type D
POSITIVE
Insert Number
Hole Type
TS (M2.5) with a = .130
.236
TS (M4) with a = .213
.217
.295
TS (M5) with a = .268
0602pp
.110
.154
TS (M2.5) with a = .130
03S1pp
.079
.114
TS (M1.6) with a = .098
04T0pp
.094
.138
TS (M2) with a = .106
0602pp
.110
.148
TS (M2.5) with a = .130
0803pp
.134
.177
TS (M3) with a = .154
09T3pp
.173
.236
TS (M4) with a = .213
43p
1204pp
.217
.295
TS (M5) with a = .268
21.5p
0602pp
.110
.148
TS (M2.5) with a = .130
09T3pp
.173
.236
TS (M4) with a = .213
1204pp
.217
.295
TS (M5) with a = .268
0802pp
.134
.177
TS (M3) with a = .154
0903pp
.173
.236
TS (M4) with a = .213
0802pp
.138
.209
78
TS (M3) with a = .197
0903pp
.177
.248
78
TS (M4) with a = .220
0602pp
.110
.148
TS (M2.5) with a = .130
09T3pp
.173
.236
TS (M4) with a = .213
0802pp
.138
.220
78
TS (M3) with a = .197
0903pp
.181
.260
80
TS (M4) with a = .220
0702pp
.110
.148
TS (M2.5) with a = .130
11T3pp
.173
.236
TS (M4) with a = .213
0702pp
.110
.148
TS (M2.5) with a = .130
11T3pp
.173
.236
TS (M4) with a = .213
1504pp
.217
.295
TS (M5) with a = .268
21.5p
CCGH
CCMH
21.5p
32.5p
43p
03S1pp
04T0pp
CCET
CCGT
CCGW
CCGH
CCMH
CCGT
21.5p
CCMT
CCMW
2.52p
32.5p
32.5p
CCMT
CCMW
43p
CPGT
CPMH
CPMT
CPMX
DCET
DCGT
DCGW
2.51.5p
32p
2.51.5p
32p
21.5p
32.5p
2.51.5p
32p
21.5p
32.5p
CPGT
CPMH
CPMT
CPMX
DCET
DCGT
DCGW
21.5p
DCMT
DCMW
32.5p
DCMT
DCMW
43p
DEGX
RCMX
Dimension (inch)
Applicable Screw
CCET
CCGT
CCGW
CCGT
(ISO) Number
43p
DEGX
D2
D3
0602pp
.110
.148
09T3pp
.173
1204pp
()
1504pp
.201
.276
85
1003M0
1003M0
.142
.177
21
1204M0
1204M0
.165
.209
21
1606M0
.205
.260
21
2006M0
.256
.311
21
2507M0
2507M0
.283
.354
21
3209M0
3209M0
.374
.457
21
1606M0
2006M0
RCMX
TURNING INSERTS
Type B
CS (M4.5) with a = .248
for lever lock holder
D
D
A005
TURNING INSERTS
TURNING INSERTS
HOLE GEOMETRY
Type C
Type D
POSITIVE
Insert Number
(ISO) Number
RCMX
2006M0-pp
2507M0-pp
.260
21
2006M0-pp
.256
.311
21
2507M0-pp
.283
.354
21
3209M0-pp
.374
.457
21
0602M0
.110
.148
TS (M2.5) with a = .130
0803M0
.134
.177
TS (M3) with a = .154
10T3M0
.173
.236
TS (M4) with a = .213
RGGM
2004M0
.220
.295
53
TS (M5) with a = .268
SCMT
SCMW
09T3pp
.173
.236
TS (M4) with a = .213
1204pp
.217
.295
TS (M5) with a = .268
0903pp
.189
.250
58
TS (M4) with a = .213
1203pp
.232
.303
58
TS (M5) with a = .268
0903pp
.181
.236
TS (M4) with a = .213
1203pp
.224
.295
TS (M5) with a = .268
0903pp
.173
.236
TS (M4) with a = .213
1203pp
.217
.295
TS (M5) with a = .268
0601pp
.091
.126
TS (M2) with a = .106
RCMT
RCGT
10T3M0
RGGM
2004M0
SCMT
SCMW
32.5p
SPGX
SPMW
SPMT
43p
32p
42p
32p
42p
32p
42p
SPGX
SPMW
SPMT
1.21p
TCGT
TCMT
TCMW
21.5p
TCGT
TPGX
TPGX
D
for lever lock holder
D
D
1102pp
.110
.148
TS (M2.5) with a = .130
16T3pp
.173
.236
TS (M4) with a = .213
1.51.5p
0802pp
.091
.118
TS (M2) with a = .106
1.81.5p
0902pp
.098
.130
TS (M2.2) with a = .118
1102pp
.110
.148
TS (M2.5) with a = .130
2.52p
1303pp
.134
.177
TS (M3) with a = .154
32.5p
16T3pp
.173
.236
TS (M4) with a = .213
21.5p
1102pp
.110
.148
TS (M2.5) with a = .130
1303pp
.134
.177
TS (M3) with a = .154
16T3pp
.173
.236
TS (M4) with a = .213
1603pp
.169
.238
88
FC (M4) with a = .220
1103pp
.138
.189
88
TS (M3) with a = .161
1603pp
.189
.250
58
TS (M4) with a = .213
0802pp
.098
.150
88
TS (M2) with a = .126
0902pp
.118
.169
88
TS (M2.5) with a = .146
0802pp
.094
.157
78
TS (M2) with a = .150
0902pp
.114
.169
78
TS (M2.5) with a = .173
1103pp
.134
.188
78
TS (M3) with a = .189
1603pp
.173
.254
78
TS (M4) with a = .220
21.5p
2.52p
TCMT
TCMW
32p
22p
32p
1.51.5p
1.81.5p
TEGX
TPGX
TPGX
1.51.5p
TPGH
32.5p
32.5p
TEGX
Hole Type
.205
0602M0
0803M0
Applicable Screw
1606M0-pp
RCMX
()
D3
3209M0-pp
RCMT
RCGT
Dimension (inch)
D2
1606M0-pp
1.81.5p
22p
32p
A006
Type B
TPGH
Type C
Type D
POSITIVE
Insert Number
(ISO) Number
TPMT
TPMX
Applicable Screw
Hole Type
D3
0802pp
.098
.157
78
TS (M2) with a = .150
0902pp
.114
.169
78
TS (M2.5) with a = .173
1103pp
.134
.189
78
TS (M3) with a = .189
32p
1603pp
.173
.254
78
TS (M4) with a = .220
1.81.5p
0902pp
.098
.130
TS (M2.2) with a = .118
1102pp
.110
.148
TS (M2.5) with a = .130
32.5p
16T3pp
.173
.236
TS (M4) with a = .213
1.51.5pL
0802ppL
.106
.150
88
TS (M2) with a = .126
0902ppL
.126
.169
88
TS (M2.5) with a = .146
1103ppL
.146
.189
88
TS (M3) with a = .161
1.81.5p
22p
21.5p
1.81.5pL
TPMH
TPMT
TPMX
22pL
()
D2
1.51.5p
TPMH
Dimension (inch)
TPMX
22p
TPMX
1103pp
.138
.189
88
TS (M3) with a = .161
VBET
22p
VBET
1103pp
.115
.148
TS (M2.5) with a = .130
1103pp
.115
.148
TS (M2.5) with a = .130
1604pp
.178
.236
TS (M4) with a = .213
1103pp
.115
.149
TS (M2.5) with a = .130
1604pp
.178
.238
TS (M4) with a = .213
0802pp
.097
.126
TS (M2) with a = .106
1604pp
.173
.236
TS (M4) with a = .213
43.5p
2205pp
.217
.295
TS (M5) with a = .268
1.51.5p
0802pp
.097
.126
TS (M2) with a = .106
1103pp
.110
.148
TS (M2.5) with a = .130
1604pp
.173
.236
TS (M4) with a = .213
1103pp
.110
.148
TS (M2.5) with a = .130
1604pp
.173
.236
TS (M4) with a = .213
1603pp
.177
.238
88
FC (M4) with a = .220
0201pp
.091
.126
TS (M2) with a = .106
L302pp
.091
.126
TS (M2) with a = .106
0201pp
.091
.118
TS (M2) with a = .106
L302pp
.091
.118
TS (M2) with a = .106
0402pp
.110
.148
TS (M2.5) with a = .130
32.5p
06T3pp
.173
.236
TS (M4) with a = .213
1.21pp
0201pp
.091
.118
TS (M2) with a = .106
L302pp
.091
.118
TS (M2) with a = .106
0402pp
.110
.148
TS (M2.5) with a = .130
06T3pp
.173
.236
TS (M4) with a = .213
0402pp
.110
.148
TS (M2.5) with a = .130
0603pp
.173
.236
TS (M4) with a = .213
1503pp
.110
.148
TS (M2.5) with a = .138
VBGT
VBMT
22p
33p
22p
33p
VBGT
VBMT
1.51.5p
VCGT
VCMT
33p
22p
VCGT
VCMT
33p
VCMW
VDGX
WBGT
22p
33p
32p
1.21pp
1.51.5pp
VCMW
VDGX
WBGT
1.21pp
WCGT
WCMT
1.51.5pp
21.5p
1.51.5pp
21.5pp
WCGT
WCMT
32.5pp
WPGT
WPMT
21.5p
32p
WPGT
WPMT
XCMT
22p
XCMT
TURNING INSERTS
Type B
A007
TURNING INSERTS
TURNING INSERTS
PRECISION BREAKER STANDARD

STANDARD OF LEFT AND RIGHT HAND INSERTS
a NEGATIVE INSERTS
Geometry
Insert Number
(ISO) Number
L3
L4
B2
B7
DNGG431R/L
DNGG150404R/L
.110
15
432R/L
150408R/L
.110
15
Right hand insert shown.
SNGG321L
SNGG090304L
.071
.063
15
432R
120408R
.091
.146
15
TNGG321L
TNGG160304L
.091
.213
15
331L
160404L
.091
.213
15
431R/L
220404R/L
.110
.370
15
L3
L4
B2
B7
30 20
a POSITIVE INSERTS
Geometry
A008
Insert Number
(ISO) Number
CCET21.5V3R/LSR
CCET0602V3R/L-SR
.087
21.50.2R/LSR
060201R/L-SR
.087
30 20
21.50.5R/LSR
060202R/L-SR
.087
30 20
21.51R/LSR
060204R/L-SR
.087
30 20
32.5V3R/LSR
09T3V3R/L-SR
.126
30 20
32.50.2R/LSR
09T301R/L-SR
.126
30 20
32.50.5R/LSR
09T302R/L-SR
.126
30 20
32.51R/LSR
09T304R/L-SR
.126
30 20
CCET21.5V0R/LSN
CCET060200R/L-SN
.039
20
21.5V3R/LSN
0602V3R/L-SN
.039
20
21.50.2R/LSN
060201R/L-SN
.039
20
21.50.5R/LSN
060202R/L-SN
.039
20
21.51R/LSN
060204R/L-SN
.039
20
32.5V0R/LSN
09T300R/L-SN
.059
20
32.5V3R/LSN
09T3V3R/L-SN
.059
20
32.50.2R/LSN
09T301R/L-SN
.059
20
32.50.5R/LSN
09T302R/L-SN
.059
20
09T304R/L-SN
.059
20
32.51R/LSN
CCET21.5V3R/LWSN
CCET0602V3R/LW-SN
.039
20
32.5V3R/LWSN
09T3V3R/LW-SN
.059
20
Geometry
Insert Number
CCGH21.50.5R/LF
21.51R/LF
(ISO) Number
L3
L4
B2
B7
CCGH060202R/L-F
.047
15 20
060204R/L-F
.055
15 20
CCGT0602V3R-SN
.039
.118
20
TURNING INSERTS
a POSITIVE INSERTS
CCGT21.5V3RSN
Left hand insert only.
21.50.2R/LSN
060201R/L-SN
.039
.118
20
21.50.5R/LSN
060202R/L-SN
.039
.118
20
32.5V3R/LSN
09T3V3R/L-SN
.059
.197
20
32.50.2R/LSN
09T301R/L-SN
.059
.197
20
32.50.5R/LSN
09T302R/L-SN
.059
.197
20
32.51R/LSN
09T304R/L-SN
.059
.197
20
CCGT03S1V3L-F
CCGT03S1V3L-F
.031
17 35
03S101L-F
03S101L-F
.031
17 35
03S102L-F
03S102L-F
.031
17 35
03S104L-F
03S104L-F
.031
17 35
04T0V3L-F
04T0V3L-F
.039
17 35
04T001L-F
04T001L-F
.039
17 35
04T002L-F
04T002L-F
.039
17 35
04T004L-F
CCGT21.5V3R/LSS
04T004L-F
CCGT0602V3R/L-SS
.039
.039
.118
17 35
14
21.50.2R/LSS
060201R/L-SS
.039
.118
14
21.50.5R/LSS
060202R/L-SS
.039
.118
14
32.5V3R/LSS
09T3V3R/L-SS
.039
.197
14
32.50.2R/LSS
09T301R/L-SS
.039
.197
14
32.50.5R/LSS
09T302R/L-SS
.039
.197
14
CPGT2.51.51R/LF
CPGT080204R/L-F
.071
15 20
320.5R/LF
090302R/L-F
.071
15 20
321R/LF
090304R/L-F
.071
15 20
CPMH080204R/L-F
.039
15 20
090304R/L-F
.055
15 20
CPMH2.51.51R/LF
321R/LF
A009
TURNING INSERTS
TURNING INSERTS

a POSITIVE INSERTS
Geometry
Insert Number
(ISO) Number
L3
L4
B2
B7
DCET21.5V3R/LSR
DCET0702V3R/L-SR
.098
30 20
21.50.2R/LSR
070201R/L-SR
.098
30 20
21.50.5R/LSR
070202R/L-SR
.098
30 20
21.51R/LSR
070204R/L-SR
.098
30 20
32.5V3R/LSR
11T3V3R/L-SR
.146
30 20
32.50.2R/LSR
11T301R/L-SR
.146
30 20
32.50.5R/LSR
11T302R/L-SR
.146
30 20
32.51R/LSR
11T304R/L-SR
.146
30 20
DCET21.5V0R/LSN
DCET070200R/L-SN
.039
20
21.5V3R/LSN
0702V3R/L-SN
.039
20
21.50.2R/LSN
070201R/L-SN
.039
20
21.50.5R/LSN
070202R/L-SN
.039
20
21.51R/LSN
070204R/L-SN
.039
20
32.5V0R/LSN
11T300R/L-SN
.059
20
32.5V3R/LSN
11T3V3R/L-SN
.059
20
32.50.2R/LSN
11T301R/L-SN
.059
20
32.50.5R/LSN
11T302R/L-SN
.059
20
.059
20
DCET21.5V3R/LWSN
32.51R/LSN
DCET0702V3R/LW-SN
11T304RL-SN
.039
20
32.5V3R/LWSN
11T3V3R/LW-SN
.059
20
DCGT21.5V3RSN
DCGT0702V3R-SN
.039
.138
20
21.50.2RSN
070201R-SN
.039
.138
20
21.50.5R/LSN
070202R/L-SN
.039
.138
20
32.5V3R/LSN
11T3V3R/L-SN
.059
.256
20
32.50.2R/LSN
11T301R/L-SN
.059
.256
20
32.50.5R/LSN
11T302R/L-SN
.059
.256
20
32.51R/LSN
11T304R/L-SN
.059
.256
20
DCGT21.50.5R/LF
DCGT070202R/L-F
.039
17 20
21.51R/LF
070204R/L-F
.039
17 20
32.50.5R/LF
11T302R/L-F
.039
14 20
32.51R/LF
11T304R/L-F
.039
14 20
A010
DCGT21.5V3R/LSS
DCGT0702V3R/L-SS
.039
.138
14
21.50.2R/LSS
070201R/L-SS
.039
.138
14
21.50.5R/LSS
070202R/L-SS
.039
.138
14
32.5V3RSS
11T3V3R-SS
.039
.256
14
32.50.2RSS
11T301R-SS
.039
.256
14
32.50.5RSS
11T302R-SS
.039
.256
14
Geometry
Insert Number
L3
L4
B2
B7
DEGX150402R/L
.110
20
431R/L
150404R/L
.110
20
432R/L
150408R/L
.110
20
TCGT0601V3L-F
.039
14 20
DEGX430.5R/L
(ISO) Number
TURNING INSERTS
a POSITIVE INSERTS
TCGT1.21V3LF
1.210.2LF
060101L-F
.039
14 20
1.210.5LF
060102L-F
.039
14 20
1.211LF
060104L-F
.039
14 20
Left hand insert only.
TEGX320.5R/L
TEGX160302R/L
.079
.236
20
321R/L
160304R/L
.079
.236
20
322R/L
160308R/L
.079
.236
20
TPGH1.51.50.5R/LFS
TPGH080202R/L-FS
.035
15 20
1.51.51R/LFS
080204R/L-FS
.035
15 20
1.81.50.5R/LFS
090202R/L-FS
.039
15 20
1.81.51R/LFS
090204R/L-FS
.039
15 20
220.5R/LFS
110302R/L-FS
.055
15 20
221R/LFS
110304R/L-FS
.055
15 20
TPGX1.51.50.5R/L
TPGX080202R/L
.051
10 20
1.51.51R/L
080204R/L
.051
10 20
1.81.50.5R/L
090202R/L
.063
10 20
1.81.51R/L
090204R/L
.063
10 20
1.81.52R/L
090208R/L
.055
10 20
220.5R/L
110302R/L
.071
10 20
221R/L
110304R/L
.071
10 20
110308R/L
.071
10 20
TPGV090202L-F
.063
10 20
222R/L
TPGV1.81.50.5LF
1.81.51R/LF
090204R/L-F
.063
10 20
220.5LF
110302L-F
.071
10 20
221R/LF
110304R/L-F
.071
10 20
VCGT1.51.50.5R/LF
1.51.51R/LF
VCGT080202R/L-F
.031
13 20
080204R/L-F
.031
13 20
A011
TURNING INSERTS
TURNING INSERTS

a POSITIVE INSERTS
Geometry
Insert Number
(ISO) Number
L3
L4
B2
B7
VDGX320R/L
VDGX160302R/L
.079
25 20
321R/L
160304R/L
.079
25 20
VBGT110302R/L-F
.039
13 20
VBGT220.5R/LF
221R/LF
110304R/L-F
.039
13 20
330.5R/LF
160402R/L-F
.059
13 20
331R/LF
160404R/L-F
.059
13 20
VBET22V3R/LSR
VBET1103V3R/L-SR
.098
30 20
220.2R/LSR
110301R/L-SR
.098
30 20
220.5R/LSR
110302R/L-SR
.098
30 20
221R/LSR
110304R/L-SR
.098
30 20
VBET22V0R/LSN
VBET110300R/L-SN
.039
20
22V3R/LSN
1103V3R/L-SN
.039
20
220.2R/LSN
110301R/L-SN
.039
20
220.5R/LSN
110302R/L-SN
.039
20
110304R/L-SN
.039
20
VBET22V3R/LWSN
221R/LSN
VBET1103V3R/LW-SN
.039
20
WBGT1.21V3LF
WBGT0201V3L-F
.039
13 30
1.210.2LF
020101L-F
.039
13 30
1.210.5LF
020102L-F
.039
13 30
1.211LF
020104L-F
.039
13 30
1.51.5V3LF
L302V3L-F
.039
13 30
1.51.50.2LF
L30201L-F
.039
13 30
1.51.50.5R/LF
L30202R/L-F
.039
13 30
L30204R/L-F
Left hand insert shown.
1.51.51R/LF
.039
13 30
WCGT020102R/L
.039
15 30
1.211R/L
020104R/L
.039
15 30
1.51.50.5R/L
L30202R/L
.039
15 30
1.51.51R/L
L30204R/L
.039
15 30
WCGT1.210.5R/L
A012
supports our customers with information and supplies suitable cutting conditions for each workpiece by selecting optimal
indexable insert together with the optional tool.
TURNING INSERTS
OUTLINE
LABEL INDICATION
z Cutting conditions
Cutting Conditions
vc (Cutting Speed)
Steel
Stainless
Cast Iron
Stable cutting
Unstable cutting
General cutting
320 190 m/min

1050 620 SFM
x Cutting areas (ap: Depth of cut per side)
220 120 m/min

720 390 SFM
c Cutting speed standards
F : Finishing (ap.020") S : Light Cutting (ap=.020" .060")

M : Medium Cutting (ap=.060".157") G : Rough Cutting (ap=.157".276")
(Performance versus tool life)
Calculations based on maximum performance : Tool life is 15min.
Calculation based on maximum tool : Tool life is 90min.
270 170 m/min

885 560 SFM
v Workpiece materials
P : Steel (Material reference : Carbon steel, alloy steel 180HB)
M : Stainless steel (Material reference : Austenitic stainless steel 180HB)
K : Cast iron (Material reference : Gray cast iron, ductile cast iron 180HB)
TOOL LIFE
Cutting speed affects tool life. Mitsubishis
suggests cutting speeds for 15/90-minute tool life and is based on Taylors equation
(Relationship for tool grade, cutting conditions and tool life). When the customer requires different tool life, obtain coefcient values of the
grade you use from the charts below. Multiply the coefcient values by the cutting speed to calculate the new cutting speed.
K Grade (Cast lron) cutting speed coefcient values.
P Grade (Steel) cutting speed coefcient values.

Tool life
30min
45min
60min
90min
UC5105
1.00
0.79
0.69
0.63
0.55
UC5115
1.00
0.79
0.69
0.63
0.55
0.62
AP25N
1.00
0.87
0.80
0.75
0.69
0.73
VP25N
1.00
0.87
0.80
0.75
0.69
30min
45min
60min
90min
UE6105
1.00
0.79
0.69
0.63
0.55
UE6110
1.00
0.82
0.72
0.67
0.59
UE6020
1.00
0.83
0.74
0.69
UE6035
1.00
0.88
0.82
0.78
AP25N
1.00
0.84
0.76
0.71
0.64
VP25N
1.00
0.84
0.76
0.71
0.64
Grade
Grade
M Grade (Stainless Steel) cutting speed coefcient values.

Tool life
15min
30min
45min
60min
90min
US735
1.00
0.78
0.68
0.61
0.53
US7020
1.00
0.70
0.57
0.49
0.40
VP15TF
1.00
0.78
0.67
0.61
0.52
AP25N
1.00
0.76
0.65
0.57
0.49
Grade
Tool life
15min
15min
(ex.) Medium cutting of steel

The 1st recommendation
Indexable inserts
Recommended cutting speed
(Tool life : 15min.)
: UE6110
: CNMG432MA
: vc = 1065SFM
Tool life required by the customer : 30min.

10650.82 = 873SFM
HARDNESS OF WORKPIECE
Hardness of the workpiece also affects tool life. Mitsubishis
suggests cutting speed variations when hardness of the workpiece
differs. Obtain the suitable coefcient value for each workpiece from the chart below. Multiply the coefcient value by the recommended
cutting speed of the grade you use to calculate the new cutting speed.
Work Material
P
M
K
(Hardness of workpiece)
Soft
Hard
140HB
180HB
220HB
260HB
1.19
1.23
1.19
1.0
1.0
1.0
0.85
0.85
0.91
0.75
0.72
0.85
A013
TURNING INSERTS
TURNING INSERTS
CLASSIFICATION OF GRADES AND CHIP BREAKERS FOR TURNING

a Selection of optimum inserts for turning
The following diagrams show for each work material, the optimal combination of suitable grades and chip breakers
for each application area in turning.
y CUTTING CONDITIONS
Stable Cutting
y CUTTING AREA
Continuous Cutting
Constant Depth of Cut
Pre-Machined
Securely Clamped Component
F
S
M
G
H
General Cutting
Unstable Cutting
Heavy Interrupted Cutting

Irregular Depth of Cut
Low Clamping Rigidity
(ap<.020inch)
Finish Cutting
Light Cutting
(ap=.020 .060inch)
Medium Cutting
(ap=.060 .157inch)
Semi-Heavy Cutting (ap=.157 .276inch)

(ap=.276 .394inch)
Heavy Cutting
Material
St
ab
le
Cu
HZ
UE6110
ttin
M ild S t e e l
HZ
MH
UE6105
MH
UE6020
MS
UE6110
MS
SY
VP25N
UE6110
MH
UE6020
SY
UC6110
UE6110
FY
VP25N
FY
HZ
UH6400
MS
UE6020
NX3035
SY
UE6020
Un
sta
ble
NX3035
1st Recommendation
(General Cutting)
FY
UE6020
Cu
ttin
Mild Steel
vc : Cutting speed
f : Feed
ap : Depth of cut.
NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
A014
F
S
M
G
H
F
S
M
G
H
F
S
M
G
H
FY
1st Recommendation
vcn (SFM)
f (IPR)
Grade

VP25N 985 1540 .003 .009
vc
FY
NX3035
SY
VP25N 850 1345 .006 .013 vc
SY
NX3035
FY
VP25N
MS NX3035
MS
UE6110 650 1440 .006 .020
vc
MS UE6020
SY
VP25N
MH UE6110
MH UE6105 885 1620 .008 .022 vc
MH UE6110
MA UE6105
GH UE6105
HZ
UE6110 655 1100 .016 .047
HZ
GH UE6110
HX
UE6110
FY
NX3035 900 1260 .003 .009 FY VP25N
FY
UE6020
, vc
SY
NX3035
SY
NX3035 770 1100 .006 .013
SY
UE6020
FY
NX3035
MS NX3035
MS
UE6110 850 1440 .006 .020 vc
MS UE6020
SY
UE6020
MH UE6110
MH
UE6110 835 1425 .008 .022
MH UE6020
MA UE6110
GH UE6110
HZ
UE6020 620 1000 .016 .047 HZ UE6110
HZ
UH6400
GH UE6020
HX
UE6020
FY
UE6020 965 1590 .003 .009
SY
UE6020
SY
UE6020
SY
UE6020 850 1375 .006 .013 SY NX3035
MS UE6020
FY
UE6020
MS UE6020
MS
UE6020 800 1310 .006 .020
MS UE6110
MH UE6020
SY
UE6020
MH UE6020
MH UE6020 785 1295 .008 .022 MH UE6110
MH UE6035
MA UE6020
GH UE6020
HZ
ap, f
GH UE6020
HX UH6400
Chip Breaker
UH6400 540 785
.016 .047
Heavy Wear
vc
SY VP25N
MH UE6105
FY
NX3035
HZ UE6020
Fracture
UE6020
Long Chips
, vc
, vc
Chip Jamming
SY
VP25N
Stable Cutting
St
ab
le
Cu
HX
UE6110
ttin
Carbon Steel
Alloy Steel
HX
General Cutting
GH
UE6105
Unstable Cutting
GH
UE6020
MA
UE6105
MA
SA
UE6105
UC6110
UE6110
FH
AP25N
FH
MA
UE6020
UE6110
SA
UE6020
NX3035
1st Recommendation
(General Cutting)
F
S
M
G
H
HX
UH6400
UE6110
GH
UE6020
SA
Un
sta
ble
FH
UE6110
Cu
ttin
Finish Cutting
Light Cutting
Medium Cutting
Semi-Heavy Cutting
Heavy Cutting
Carbon Steel Alloy Steel
vc : Cutting speed
f : Feed
ap : Depth of cut.
NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
S
M
G
H
F
S
M
G
H
F
S
M
G
H
FH
1st Recommendation
vcn (SFM)
f (IPR)
Grade
AP25N 755 1180 .003 .008
vc
FH
NX3035
, vc
SA
SA
UE6105 720 1330 .004 .016 vc
SA
UE6110
FH
UE6110
MA UE6105
MA
UE6105 655 1210 .008 .020 vc
MA UE6110
SA
UE6105
GH
UE6105 590 1100 .010 .024 vc
GH UE6110
MH UE6105
HZ
Chip Breaker
TURNING INSERTS
Material
Heavy Wear
Fracture
Long Chips
Chip Jamming
AP25N
MH UE6105
UE6110
HX
UE6110 475 800 .018 .049 vc
HX UE6020
HZ
UE6110
HV
UE6110
FH
NX3035 690 965 .003 .008 FH AP25N
FH
UE6110
, vc
SA
NX3035
SA
UE6110 690 1165 .004 .016 SA UE6105
SA
UE6020
FH
UE6110
MA UE6110
MA
UE6110 620 1065 .008 .020 MA UE6105
MA UE6020
SA
UE6110
MH UE6110
GH
UE6110 555 950 .010 .024 GH UE6105
GH UE6020
MH UE6110
HZ
UE6110
HX
UE6020 460 740 .018 .049 HX UE6110
HX UH6400
HZ
HV
UE6020
FH
UE6110 785 1345 .003 .008 vc
FH
, vc
SA
UE6110
SA
UE6020 655 1065 .004 .016 SA UE6110
MP UE6020
FH
UE6020
MA UE6020
MA
UE6020 590 965 .008 .020 MA UE6110
MH UE6020
SA
UE6020
MH UE6020
GH
UE6020 540 870 .010 .024 GH UE6110
GH US735
MH UE6020
HZ
HX
UH6400 410 590 .018 .049 HX UE6020
ap, f
HZ
HV UH6400
UE6020
UE6020
UH6400
CHIPBREAKER SYSTEM
UE6020
A040
A015
TURNING INSERTS
TURNING INSERTS

Material
St
Stable Cutting
ab
le
Cu
Stainless Steel
ttin
General Cutting
Unstable Cutting
F
S
M
G
H
Un
sta
ble
1st Recommendation
(General Cutting)
Cu
ttin
Finish Cutting
Light Cutting
Medium Cutting
Semi-Heavy Cutting
Heavy Cutting
vc : Cutting speed
f : Feed
ap : Depth of cut.
Stainless Steel
NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
A016
F
S
M
G
H
F
S
M
G
H
F
S
M
G
H
FH
1st Recommendation
vcn (SFM)
f (IPR)
Grade
US735 360 690 .003 .008
vc
SA US735
SA
US735
310 605 .004 .016
vc
MS US735
FH
MS US7020 310 800 .006 .020 vc
MS US735
MA US7020
MH US7020
GH US7020 280 720 .010 .024 vc
GH US735
MH US7020
HZ US7020 245 605 .016 .047 vc
HZ US735
GH US7020
SA US735
Chip Breaker
FH
US735
360 690 .003 .008
SA
Heavy Wear
vc
Fracture
Long Chips
Chip Jamming
SA
US735
MS US7020
US735
f
SA
US735
US735
310 605 .004 .016
vc
MS US735
FH
US735
MS US735
MS US735
280 540 .006 .020
MS US7020
MA US735
MA US735
GH US735
GH US735
260 490 .010 .024
GH US7020
ap, f
MA US735
HZ US735
215 410 .016 .047
HZ US7020
ap, f
GH US735
FH
US735
360 690 .003 .008
vc
SA US735
SA
SA
US735
310 605 .004 .016
vc
MS US735
FH
US735
MS US735
MS US735
280 540 .006 .020
MS US7020
MA US735
MA US735
GH US735
GH US735
260 490 .010 .024
GH US7020
ap, f
MA US735
HZ US735
215 410 .016 .047
HZ US7020
ap, f
GH US735
US735
St
Stable Cutting
ab
le
Flat Top
Cu
ttin
Cast Iron
Ductile Cast Iron
Flat Top
General Cutting
Standard
TURNING INSERTS
Material
Unstable Cutting
Standard
F
S
M
G
Flat Top
Standard
Un
sta
ble
1st Recommendation
(General Cutting)
Cast Iron Ductile Cast Iron

NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
S
M
G
F
S
M
G
F
S
M
G
Light Cutting
Medium Cutting
Semi-Heavy Cutting
Cu
ttin
vc : Cutting speed
f : Feed
ap : Depth of cut.
MA
1st Recommendation
Heavy Wear
vcn (SFM)
f (IPR)
Grade
UC5105 540 1000 .008 .020 vc
MA
UC5115
MA
UC5105 540 1000 .008 .020 vc
MA
UC5115
Chip Breaker
Finish Cutting
Fracture
Standard UC5105 540 1000 .010 .024 vc
Standard UC5115
Flat Top UC5105 510 950 .008 .024 vc
Flat Top UC5115
MA
UC5115 525 965 .008 .020 MA
UC5105 Standard UC5115
MA
UC5115 525 965 .008 .020 MA
Standard UC5115 525 965 .010 .024 Standard UC5105 Flat Top UC5115
Flat Top UC5115 510 920 .008 .024 Flat Top UC5105 ap, f
MA
UC5115 525 965 .008 .020 MA
MA
UC5115 525 965 .008 .020 MA
Standard UC5115 525 965 .010 .024 Standard UC5105 Flat Top UC5115
Flat Top UC5115 510 920 .008 .024 Flat Top UC5105 ap, f
CHIPBREAKER SYSTEM
A040
A017
TURNING INSERTS
TURNING INSERTS

Material
St
ab
Stable Cutting
le
Cu
ttin
Titanium Alloy
General Cutting
Unstable Cutting
F
S
M
G
Un
sta
ble
1st Recommendation
(General Cutting)
Finish Cutting
Light Cutting
Medium Cutting
Semi-Heavy Cutting
Cu
ttin
Titanium Alloy
vc : Cutting speed
f : Feed
ap : Depth of cut.
NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
A018
F
S
M
G
F
S
M
G
F
S
M
G
FJ
1st Recommendation
vcn (SFM)
f (IPR)
Grade
RT9010 165 330 .002 .008
vc
FJ
TF15
MJ
RT9010 130 295 .002 .010
vc
MJ
TF15
MS
RT9010 130 260 .004 .010
vc
GJ
RT9010 130 230 .006 .014
vc
FJ
RT9010 165 330 .002 .008
vc
FJ
TF15
MJ
RT9010 130 295 .002 .010
vc
MJ
TF15
MS
RT9010 130 260 .004 .010
vc
GJ
RT9010 130 230 .006 .014
vc
FJ
TF15
130 260 .002 .008
FJ
MJ
TF15
100 230 .002 .010
MJ RT9010
MS TF15
MS
TF15
100 195 .004 .010
MS RT9010
GJ
GJ
TF15
100 165 .006 .014
GJ RT9010
ap, f
Chip Breaker
Heavy Wear
RT9010
Fracture
Long Chips
Chip Jamming
MJ RT9010
RT9010
MS TF15
GJ RT9010
GJ
FJ
TF15
MJ RT9010
RT9010
MS TF15
GJ RT9010
GJ
TF15
MJ
TF15
TF15
FJ
FJ
MJ TF15
TF15
GJ TF15
St
ab
Stable Cutting
le
Cu
ttin
Ni, Co-Based Alloy
General Cutting
TURNING INSERTS
Material
Unstable Cutting
F
S
M
G
Un
sta
ble
1st Recommendation
(General Cutting)
Finish Cutting
Light Cutting
Medium Cutting
Semi-Heavy Cutting
Cu
ttin
Ni, Co-Based Alloy
vc : Cutting speed
f : Feed
ap : Depth of cut.
NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
S
M
G
F
S
M
G
F
S
M
G
Chip Breaker
FJ
1st Recommendation
vcn (SFM)
f (IPR)
Grade
VP10RT 65 195 .002 .008
Heavy Wear
vc
Fracture
VP15TF
MJ VP10RT
f
MS VP10RT
GJ
GJ
VP15TF
VP15TF
MJ VP10RT
MS VP05RT 100 230 .004 .010 MS US905

65 130 .006 .014
FJ
GJ US905
Chip Jamming
VP10RT
FJ
MJ VP05RT 100 230 .002 .010 MJ US905

GJ VP10RT
Long Chips
VP10RT
65 195 .002 .008
vc
FJ
MJ VP10RT
65 165 .002 .010
MJ VP05RT
MJ VP15TF
MS VP10RT
65 165 .004 .010
MS VP05RT
GJ VP10RT
65 130 .006 .014
GJ US905
FJ
FJ
VP10RT
MJ VP10RT
VP10RT
MS VP15TF
GJ
GJ
FJ
VP15TF
VP15TF
65 195 .002 .008
FJ
VP10RT
MJ VP15TF
MJ VP15TF
65 165 .002 .010
MJ VP10RT
MS VP15TF
MS VP15TF
65 165 .004 .010
MS VP10RT
GJ
GJ VP15TF
65 130 .006 .014
GJ VP10RT
ap, f
VP15TF
FJ
VP10RT
MJ VP15TF
VP15TF
GJ
CHIPBREAKER SYSTEM
VP15TF
A040
A019
TURNING INSERTS
TURNING INSERTS

F
S
Stable Cutting
General Cutting
Finish Cutting
Light Cutting
Unstable Cutting
Material
St
St
ab
le
Material
ab
M ild S t e e l
Cu
le
Carbon Steel
Alloy Steel
Cu
ttin
ttin
g
Standard
Standard
UE6110
UE6110
Standard
Standard
FV
NX2525
FV
NX2525
FV
UE6110
FV
UE6110
Standard
UE6020
NX3035
FV
UE6020
NX3035
FV
UE6020
Un
ble
Un
sta
sta
1st Recommendation
(General Cutting)
Standard
UE6020
Cu
ttin
ble
1st Recommendation
(General Cutting)
Cu
ttin
Mild Steel
vc : Cutting speed
f : Feed
7 POSITIVE INSERT TYPE

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
S
F
S
F
S
Chip Breaker
FV
1st Recommendation
vcn (SFM)
f (IPR)
Grade

.008
755
1080
.002
NX2525
Heavy Wear
FV
AP25N
Standard UE6110 705 1180 .002 .012 vc

FV
NX3035 720 1030 .002 .008
FV
NX2525
Standard UE6110 705 1180 .002 .012 vc

FV
UE6020 785 1295 .002 .008
vc
Standard UE6020 655 1080 .002 .012 Standard UE6110
Fracture
FV
NX3035
Long Chips
f
, vc
Standard UE6020
FV
UE6020 f
FV
, vc
Standard UE6020
FV
UE6020 f
Standard UE6020
, vc
Standard US735
FV
UE6020 f
UE6020
Stable Cutting
General Cutting
Unstable Cutting
A020
F
S
F
S
F
S
Chip Breaker
FV
1st Recommendation
vcn (SFM)
f (IPR)
Grade

NX2525 555 800 .002 .008
Heavy Wear
FV
AP25N
Standard UE6110 525 885 .002 .012 vc

FV
Standard NX2525
Standard UE6110
Standard UE6020
vc : Cutting speed
f : Feed
7POSITIVE INSERT TYPE

Cutting Area
Chip Jamming
NX3035 540 770 .002 .008 FV NX2525
Fracture
FV
NX3035
Standard UE6020
FV
UE6020
Long Chips
Chip Jamming
, vc
Standard NX2525
FV
UE6020
, vc
Standard UE6110
FV
UE6020
Standard UE6110 525 885 .002 .012 vc
Standard UE6020
UE6020 590 965 .002 .008 vc
Standard UE6020
, vc
Standard UE6020
Standard US735
FV
UE6020
FV
Standard UE6020 490 800 .002 .012 Standard UE6110
General Cutting
Unstable Cutting
Finish Cutting
Light Cutting
Medium Cutting
Material
Material
St
St
ab
le
TURNING INSERTS
F
S
M
Stable Cutting
ab
Cu
Stainless Steel
ttin
le
Cu
ttin
Cast Iron
Ductile Cast Iron
Flat Top
Standard
Flat Top
Standard
Standard
Standard
Standard
Standard
Standard
Flat Top
Standard
Standard
Standard
Standard
Un
ble
1st Recommendation
(General Cutting)
Un
Standard
sta
Cu
ttin
sta
ble
1st Recommendation
(General Cutting)
ttin
Stainless Steel
vc : Cutting speed
f : Feed
ap : Depth of cut.

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
S
F
S
F
S
1st Recommendation
vcn (SFM)
f (IPR)
Grade

.012
230
460
.002
Standard US735
Chip Breaker
Heavy Wear
Stable Cutting
General Cutting
Unstable Cutting
Long Chips
Chip Jamming
ap, f
, vc
Standard US735 230 460 .002 .012
vc
ap, f
, vc
230 460 .002 .012
vc
ap, f
, vc
Standard US735 230 460 .002 .012
vc
ap, f
, vc
230 460 .002 .012
vc
ap, f
, vc
Standard US735 230 460 .002 .012
vc
ap, f
, vc
Standard US735
Standard US735
F
S
M
F
S
M
F
S
M
Fracture
vc

Cutting Area
Cu
Chip Breaker
vc : Cutting speed
f : Feed
ap : Depth of cut.
1st Recommendation
Heavy Wear
vcn (SFM)
f (IPR)
Grade
UC5115 440 800 .002 .012 vc
Standard UE6110
440 800 .002 .012 vc
Standard UE6110
460 835 .003 .012 vc
Flat Top UC5115
440 800 .002 .012 vc
Standard UE6110
440 800 .002 .012 vc
Standard UE6110
Standard
Standard UC5115
Flat Top UC5105
Standard UC5115
Standard UC5115
Flat Top UC5115
Standard UC5115
Standard UC5115
Flat Top UC5115
Fracture
440 800 .003 .012 Flat Top UC5105 ap, f

440 800 .002 .012 vc
Standard UE6110
440 800 .002 .012 vc
Standard UE6110
440 800 .003 .012 Flat Top UC5105 ap, f
CHIPBREAKER SYSTEM
A054
A021
TURNING INSERTS
TURNING INSERTS

Material
St
Stable Cutting
ab
le
Cu
Aluminum Alloy
ttin
General Cutting
Unstable Cutting
F
S
Finish Cutting
Light Cutting
Un
sta
ble
1st Recommendation
(General Cutting)
Cu
ttin
vc : Cutting speed
f : Feed
ap : Depth of cut.
Aluminum Alloy
Cutting area
Stable Cutting
General Cutting
Unstable Cutting
Chip Breaker
F
F
F
1st Recommendation
vcn (SFM)
f (IPR)
Grade
HTi10 985 2295 .004 .016
AZ
AZ HTi10
AZ HTi10
Heavy Wear
Fracture
Long Chips
vc
ap, f
, vc
985 2295 .004 .016
vc
ap, f
, vc
985 2295 .004 .016
vc
ap, f
, vc
Material
Material
St
St
ab
le
ab
Cu
Titanium Alloy
ttin
le
Cu
Ni, Co-Based Alloy
ttin
Un
Un
sta
ble
1st Recommendation
(General Cutting)
sta
Cu
ttin
ble
1st Recommendation
(General Cutting)
Cu
ttin
vc : Cutting speed
f : Feed
ap : Depth of cut.
Titanium Alloy
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
S
F
S
F
S
Chip Breaker
1st Recommendation
vcn (SFM)
f (IPR)
Grade
Heavy Wear
Fracture
Long Chips
FJ-P RT9005 130 295 .002 .005
vc
ap, f
MJ-P RT9005 130 295 .002 .006
vc
ap, f
FJ-P RT9005
FJ-P RT9005 130 295 .002 .005
vc
ap, f
MJ-P RT9005 130 295 .002 .006
vc
ap, f
FJ-P RT9005
FJ-P RT9005 130 295 .002 .005
vc
ap, f
MJ-P RT9005 130 295 .002 .006
vc
ap, f
FJ-P RT9005

Cutting Area
General Cutting
A022
Unstable Cutting
F
S
F
S
F
S
Chip Breaker
Chip Jamming
MJ-P RT9005
f
MJ-P RT9005
f
MJ-P RT9005
f
vc : Cutting speed
f : Feed
ap : Depth of cut.
Ni, Co-Based Alloy
Stable Cutting
Chip Jamming
1st Recommendation
vcn (SFM)
f (IPR)
Grade
Heavy Wear
Fracture
Long Chips
Chip Jamming
MJ VP10RT
FJ
VP10RT 65 165
.002 .005
vc
ap, f
MJ
VP10RT 65 165
.002 .006
vc
ap, f
FJ VP10RT
FJ
VP10RT
65 165
.002 .005
vc
ap, f
MJ
VP10RT 65 165
.002 .006
vc
ap, f
FJ VP10RT
FJ
VP10RT
65 165
.002 .005
vc
ap, f
MJ
VP10RT 65 165
.002 .006
vc
ap, f
FJ VP10RT
f
MJ VP10RT
f
MJ VP10RT
f
General Cutting
Unstable Cutting
Finish Cutting
Light Cutting
Medium Cutting
Material
St
Material
St
ab
ab
le
Cu
Mi l d Steel
ttin
le
Cu
Carbon Steel
Alloy Steel
ttin
Un
Un
sta
ble
1st Recommendation
(General Cutting)
sta
Cu
ttin
ble
1st Recommendation
(General Cutting)
Cu
ttin
Mild Steel
vc : Cutting speed
f : Feed
ap : Depth of cut.

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
S
M
F
S
M
F
S
M
FV
1st Recommendation
vcn (SFM)
f (IPR)
Grade
NX2525 755 1080 .002 .008
SV
NX2525 755 1080 .002 .010 vc
MV
NX2525 640 900 .003 .012 MV AP25N
Chip Breaker
Heavy Wear
vc
Fracture
FV
Long Chips
VP15TF f
SV NX3035 f
, vc
MV NX2525
MV NX3035 SV
NX2525
FV
NX3035 720 1030 .002 .008 FV NX2525 FV VP15TF f
, vc
SV
NX3035 540 770 .002 .010 SV NX2525 SV VP45N
, vc
MV NX3035
MV
NX3035 460 640 .003 .012 MV NX2525 MV VP25N
SV
NX3035
FV
UE6020 785 1295 .002 .008 FV NX3035 ap, f
, vc
SV
UE6020 965 1295 .002 .010 SV US7020 SV VP15TF f
, vc
MV UE6020
MV
UE6020 490 800 .003 .012 MV US7020 MV VP15TF SV
UE6020
vc : Cutting speed
f : Feed
ap : Depth of cut.

Cutting Area
General Cutting
Unstable Cutting
F
S
M
F
S
M
F
S
M
Chip Jamming
, vc
Stable Cutting
TURNING INSERTS
F
S
M
Stable Cutting
FV
1st Recommendation
vcn (SFM)
f (IPR)
Grade

NX3035 540 770 .002 .008
SV
NX3035 540 770 .002 .010 SV
NX2525 SV VP45N
MV
NX3035 460 640 .003 .012
NX2525 MV VP45N
FV
UE6020 590 965 .002 .008 FV
SV
UE6020 590 965 .002 .010
MV
UE6020 490 800 .003 .012 MV US7020 MV VP15TF SV
UE6020
FV
VP15TF 295 620 .002 .008
, vc
SV
VP15TF 295 620 .002 .010 SV
UE6020 MV VP15TF f
, vc
MV VP15TF
MV
VP15TF 230 490 .003 .012
UE6020 ap, f
VP15TF
Chip Breaker
Heavy Wear
vc
MV
SV
FV
MV
Fracture
Long Chips
R/L-FS VP15TF f
Chip Jamming
, vc
, vc
MV NX3035
SV
NX3035
NX3035 R/L-FS VP15TF f
, vc
US7020 SV VP15TF f
, vc
MV UE6020
UE6020 ap, f
SV
CHIPBREAKER SYSTEM
A054, A060
A023
TURNING INSERTS
TURNING INSERTS

Stable Cutting
General Cutting
Unstable Cutting
F
S
M
Finish Cutting
Light Cutting
Medium Cutting
Material
Material
St
St
ab
ab
le
Cu
Stainless Steel
ttin
le
Cu
Cast Iron
Ductile Cast Iron
ttin
Un
Un
sta
sta
ble
1st Recommendation
(General Cutting)
Cu
ttin
ble
1st Recommendation
(General Cutting)
Cu
ttin
vc : Cutting speed
f : Feed
ap : Depth of cut.
Stainless Steel
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
S
M
F
S
M
F
S
M
FV
1st Recommendation
vcn (SFM)
f (IPR)
Grade
VP15TF 360 620 .002 .008
vc
ap, f
SV
US7020 310 800 .002 .010
vc
SV
US735
MV
US7020 260 670 .003 .012
vc
MV
US735
vc
ap, f
Chip Breaker
Heavy Wear
Stable Cutting
General Cutting
Unstable Cutting
A024
SV
Chip Jamming
MV US7020
US7020
VP15TF 360 620 .002 .008
SV
US735
280 540 .002 .010
SV US7020 SV
VP15TF
MV US735
MV
US735
230 460 .003 .012
MV US7020 MV
VP15TF SV
US735
FV
VP15TF 360 620 .002 .008
vc
SV
VP15TF 360 620 .002 .010
SV US7020 MV
MV VP15TF
MV
VP15TF 260 525 .003 .012
MV US7020 ap, f
VP15TF
ap, f
FV
1st Recommendation
vcn (SFM)
f (IPR)
Grade

.008
245
490
.002
VP15TF
vc
ap, f
SV
VP15TF 245 490 .002 .010
vc
MV
MV
VP15TF 195 390 .003 .012
vc
ap, f
FV
VP15TF 245 490 .002 .008
vc
ap, f
SV
VP15TF 245 490 .002 .010
vc
MV
MV
VP15TF 195 390 .003 .012
vc
ap, f
FV
VP15TF 245 490 .002 .008
vc
ap, f
SV
VP15TF 245 490 .002 .010
vc
MV
MV
VP15TF 195 390 .003 .012
vc
ap, f
Chip Breaker
VP15TF
SV
vc : Cutting speed
f : Feed
ap : Depth of cut.
F
S
M
F
S
M
F
S
M
Long Chips
FV

Cutting Area
Fracture
Heavy Wear
Fracture
VP15TF
VP15TF
VP15TF
St
Stable Cutting
ab
le
Cu
Aluminum Alloy
ttin
General Cutting
Unstable Cutting
TURNING INSERTS
Material
Finish Cutting
Un
sta
ble
1st Recommendation
(General Cutting)
Cu
ttin
vc : Cutting speed
f : Feed
ap : Depth of cut.
Aluminum Alloy
Cutting Area
F
F
F
Stable Cutting
General Cutting
Unstable Cutting
R/L-FS
1st Recommendation
vcn (SFM)
f (IPR)
Grade

.005
655
1310
.002
HTi10
vc
ap, f
R/L-FS
HTi10 655 1310 .002 .005
vc
R/L-FS
HTi10 655 1310 .002 .005
vc
Chip Breaker
Heavy Wear
Fracture
Long Chips
f
, vc
ap, f
, vc
ap, f
, vc
f
Material
Material
St
St
ab
le
ab
Titanium Alloy
Cu
ttin
le
Ni, Co-Based Alloy
Cu
ttin
Un
Un
sta
sta
ble
1st Recommendation
(General Cutting)
Cu
ttin
ble
1st Recommendation
(General Cutting)
vc : Cutting speed
f : Feed
ap : Depth of cut.
Stable Cutting
General Cutting
Unstable Cutting
F
F
F
1st Recommendation
vcn (SFM)
f (IPR)
Grade
Heavy Wear
R/L-FS
HTi10 130 280
.002 .005
vc
ap, f
R/L-FS
HTi10 130 280
.002 .005
vc
ap, f
R/L-FS
HTi10 130 280
.002 .005
vc
ap, f
Chip Breaker
Fracture
Stable Cutting
General Cutting
Unstable Cutting
F
F
F
Chip Breaker
1st Recommendation
vcn (SFM)
f (IPR)
Grade
Chip Jamming
vc : Cutting speed
f : Feed
ap : Depth of cut.
Ni, Co-Based Alloy

Cutting Area
Cu
ttin
Titanium Alloy
Cutting Area
Chip Jamming
Heavy Wear
Fracture
Chip Jamming
R/L-FS VP15TF 65 165 .002 .005
vc
ap, f
R/L-FS VP15TF 65 165 .002 .005
vc
ap, f
R/L-FS VP15TF 65 165 .002 .005
vc
ap, f
f
CHIPBREAKER SYSTEM
A060
A025
BREAKER SYSTEMS FOR SMALL SIZE INSERTS

ANGULAR AND PARALLEL CHIP BREAKER
y CHIP CONTROL RANGES
3-DIMENSIONAL CHIP BREAKER

y CHIP CONTROL RANGES
General Steel
Stainless Steel
General Steel
Stainless Steel
SN
R/L
Breaker
Breaker
Breaker Breaker
FS
Breaker
Standard
SMG
Depth of Cut (inch)
Depth of Cut (inch)
SS
SR
Difcult-to-Cut Materials
Standard
Breaker
Depth of Cut (inch)
TURNING INSERTS
TURNING INSERTS
MV
Breaker Breaker
SV
FV
Breaker
Breaker
Feed (IPR)
MJ
Breaker
FJ
Breaker
Feed (IPR)
Feed (IPR)
y FEATURES OF CHIP BREAKER

Breaker
SMG
(G class)
FV
(M class)
SV
(M class)
MV
(M class)
Standard
(M class)
FJ
MJ
Features
For medium cutting.
3D moulded chipbreaker
provides good chip control.
Breaker geometry appropriate
for copying and back turning.
a Sharp cutting edge and low
resistance design dots achieve
excellent cutting performance.
a Suitable for low depth of cut and
low feed rates.
a For light cutting.
a The double design dots promote
chip discharge for mild steel
machining and at low depth of
cut machining.
a A positive insert and the large rake angle
achieve sharp cutting edge performance.
a The double breakers and round-shaped
dots in the rake face achieve a wide
range of chip discharge.
a For medium cutting.
a Balance of edge strength and sharpness
due to a combination of a at land and
large rake angle.
a The curved cutting edges support
changes in cutting depth-smooth
chip discharge and disposal.
a The large rake angle highly suitable
for nishing difcult-to-cut materials.
a The curved cutting edges support
changes in cutting depth-smooth
a Large rake angle highly suitable for nishlight cutting difcult-to-cut materials.
Features
For precision nishing.
Narrow angled breaker provides
optimal chip control.
a Sharp cutting edge generates
excellent surface nish.
a For nish cutting.
a Angled breaker controls chip ow.
a Sharp cutting edge generates
a
a
R/L
Standard
CCMH/CCMT
CPMH/CPMT
Type
DCMT
Type
a
a
Breaker
FS
CCGH/CCGT
Type
Breaker
TPMH
Type
VBGT/VBMT
Type
VCMT
Type
WBMT/WCGT
Type
CCGH/CCGT CPGT Type DCGT Type TPGH Type TPGV/TPGT TCGT Type VBGT/VCGT WBGT Type WCGT Type WPGT Type
Type
Type
Type

For light cutting.

Good chip control at low to
medium feed rates.
Features
TCGT/TCMT
Type
Angled breaker for light cutting.

Good chip control at low to
medium feed rates.
The wide angled breaker for

medium cutting is suitable for
Swiss type lathe machining.
a The insert design for low
resistance controls chip ow.
a The parallel breaker for light
cutting is suitable for Swiss
type lathe machining.
a Excellent chip control at low
feed rate.
a The parallel breaker for general
purpose is suitable for Swiss
type lathe machining.
a Excellent chip control for low to
medium feed rates.
DCGT
Type
CCET Type
CCGT Type
DCET Type
DCGT Type

VBET Type
SR
SS
SN
A026

ANGULAR AND PARALLEL CHIP BREAKERS (NEGATIVE INSERTS)

CHIP CONTROL RANGES
FEATURES OF CHIP BREAKER

Features
DNGG
Type
SNGG
Type

Narrow width angled breaker
for good chip c.ontrol.
a Sharp cutting edge produces
Finish cutting.
Angled breaker controls
chip ow.
a Sharp cutting edge produces
Breaker
TNGG
Type
VNGG
Type
TURNING INSERTS
PRECISION BREAKER SYSTEM (NEGATIVE INSERTS)
Depth of Cut (inch)
a
a
R/L
Breaker
FS
K
Breaker
F
Breaker
a
a
FS
Breaker
Parallel breaker for light

cutting.
Excellent chip control at
low to medium feed rates.
Parallel breaker for medium

cutting.
a Good chip control at medium
feed rates.
a
R/L
Feed (IPR)
A027
TURNING INSERTS
TURNING INSERTS
WIPER INSERT
a Improving Surface Finish Roughness
Under the same machining conditions against conventional breakers, but with the feed
rate increased, the surface nish of the workpiece can be maintained.
What is a Wiper Insert?
a Improving Efciency
High feed rates not only shortened machining times but employing a wiper also makes it
possible to combine roughing and nishing operations.
The wiper insert is designed with a short, at edge

that is located where the straight edge meets the
corner radius.
Wiper
In comparison to conventional
breakers, the surface nish is maintained
even if the feed rate is doubled.
Machining at high feed rates
improves cutting efciency.
Finished surface
Same surface
roughness
Wiper insert
with
a Increased Tool life

When wiper inserts are employed, the high feed rate possible reduces the time in cut
therefore, delaying the progression of wear and increasing insert tool life.
a Improving Chip Control

Under high feed conditions, the chips generated become thicker and are more easily
broken, thus, chip control is improved.
Standard insert
with
Reduced machining time

Increased production rate
Improved chip control
The conventional feed condition
High feed (The feed rate is doubled.)
y Wiper insert + machining at conventional feed rates
*Wiper inserts allow high feed rates.

Surface Roughness
Rz(!inch)
yWiper insert + machining at high feed rates
Standard Insert
Wiper Insert
MW Breaker
<Cutting Condition>
Workpiece : AISI1045
Insert : CNMG432pp
Cutting Speed=655SFM
Depth of Cut=.059inch
Feed rate=.008 .024inch/rev
with ood coolant
Eliminating the nishing step

(Combine roughing and nishing into single pass.)
Reducing cost
Increased productivity
Reduced machine down time
Feed f (inch/rev)
The surface roughness does not deteriorate even when the feed rate is doubled (.012|.024) !
<Real cost reduction!!>
The Estimation of nished surface roughness when using a wiper insert
Wipers are effective when external

machining, boring and facing.
In case the
angle is more
than 5
Rz(W)= Finished surface roughness when

using a wiper insert.
Rz: Finished surface roughness in
conventional conditions.
(In using a standard insert)
The surface roughness when machining at corner R

or taper angle over 5, is same quality as machining
with the standard inserts.
Effective uses of a wiper insert

Non effective uses of a wiper insert
Special attention is not necessary when using CNMG WNMG CCMT types
No Restriction for Holder
End CuttingAngle
The standard holder can be used as it is.

( The double clamp, highly rigid holder
is recommended.)
75
End Cutting Angle
No
restriction
95
The CNMG type can

be used as a wiper at
100corner.
No machining program
adjustment necessary
The conventional machining
program can be used as it is.
(The CNMG WNMG CCMT
types are based
on ISO/ANSI
Unnecessary
standards.)
of adjusting
Special attention is necessary when using DNMX TNMX types due to the special top face geometry
Restriction for Holder
Use a holder with an end cutting angle of 93to improve wiper efciency. A holder with a
cutting edge angle of 91can marginally improve wiper efciency (see the gure below),
however, there is no wiper efciency with other end cutting angles (60, 90, 107etc.).
The hole geometry of the DNMX and TNMX type are

the same as the DNMG and TNMG types.
The "X" represents the special geometry of Nose point.
End Cutting Angle
(Specied)
Theoretical Surface
Roughness Rz (!inch)
Ex):Theoretical surface roughness of

holders in using the TNMX160412-MW.
Standard nose radius
If dimensional errors occur,

please adjust machining program
to compensate for insert nose
conguration.
(The DNMX TNMX types are
not based on the ISO/ANSI.
Please refer to the next page.)
Standard
nose radius
Wiper
nose radius
Adjustment
necessity
Feed f (inch/rev)
A028
Necessary Adjustment of the

Machining Program
<A brief structure of insert point>
TURNING INSERTS
MACHINING PROGRAM ADJUSTMENTS FOR DNMX AND TNMX INSERTS

A) Turning and facing
Adjusting toward Z-axis
Adjusting the differential between a standard insert and Z-axis / X-axis.
Adjusting toward X-axis
Standard insert
DNMX, TNMX
type
Standard insert
(Not dependent
on the nose radius)
inch
DNMX, TNMX
type
inch
inch
Nose radius .016,.031:

Nose radius .047
B) Machining a form or taper

Required to machine an accurate form or taper.
Move the tool perpendicular to the machined surface.
Geometry
of adjusted program
(Note) Adjust the drive-in angle toward the normal line when the part where the
adjust number in minus ('=60 70) is not machined completely.
of
h t
pt r-cu
e
D ve
o
The actual
machining geometry
of
pth ut
Dever-c
o
Classication
Taper Angle '

Nose Radius
-25 -15
-10
-5
10
15
20 35
40
45
50
55
60 65
70
75 85
90
.047
.0016
.0012
.0004
.0008
.0012
.0016
.0020
.0016
.0016
.0008
.0004
-.0004
.0004
.031
.0012
.0008
.0004
.0004
.0008
.0012
.0016
.0012
.0012
.0008
-.0004
.0004
.016
.0008
.0004
.0004
.0004
.0004
.0008
.0008
.0008
.0004
.0004
-.0004
-.0004
Values| + numbers:adjustment of relief angle, -numbers:adjustment of plunge in angle (inch)
C) Compensation when machining a corner radius

1) Tool path adjustment method
Machine the correct form by altering the tool path corner radius.
Programmed corner radius = Part print (P/P) corner radius +
compensation factor.
Nose radius
Programmed corner radius
.016
.031
.047
P/P + .0020"
Ex): In the case of machining a corner with a radius R .079 when using
an insert with a nose radius R .047.
Geometry
of adjusted program
P/P + .0043"
P/P + .0055"
Work radius Adjusted conditions
Work radius.079
Work radius.079
The actual
machining geometry
2) Nose radius adjustment method

Machine the correct form by altering the insert nose radius value
in the machine program.
It is not necessary to alter the tool path when using this method
however, a dimensional error of up to +/- .0012" may occur.
Nose radius
Adjusted nose radius value
.016"
.031"
.047"
.0142"
.0229"
.0457"
Ex): In the case of machining a corner with a radius R .079 when using
an insert with a nose radius R .047.
(Note) The correction value is the same for both DNMX and TNMX inserts. Discriminate between them only by the different nose radius.
A029
TURNING INSERTS
TURNING INSERTS
GRADES FOR TURNING

a INDEXABLE INSERT GRADES FOR TURNING
ISO
P01
Steel
P10
P20
P30
P40
M01
Stainless Steel
M10
M20
M30
M40
Cast Iron
K01
K10
K20
K30
Heat Resistant Alloy Ti Alloy
Non-Ferrous Metal
N01
N10
N20
N30
S01
S10
S20
S30
Hardened Steel
H01
H10
H20
H30
A030
Coated Carbide
CVD
PVD
Cermet
Coated
Cermet
CBN
PCD
CBN
Cemented (
(Sintered
Coated (
)
Carbide
Non-coated
CBN
CBN)
Diamond)
STEEL
STAINLESS STEEL
TURNING INSERTS
TURNING APPLICATION RANGE

Cermet and Coated Cermet
CVD Coated Carbide

PVD Coated Carbide
Cemented Carbide
Cutting Speed (SFM)
Cutting Speed (SFM)
1310
985
655
AP25N
VP25N
NX2525
US7020
US735
330
CVD PVD Coated Carbide
VP15TF
UP20M
VP10RT VP20RT
Cemented Carbide
UTi20T
0
.008
.016
Feed (inch/rev)
.024
.032
Feed (inch/rev)
CAST IRON
NON-FERROUS METAL
Sintered CBN
Solid CBN
1310
MB710
MB730
MBS140
2625
MD220
CVD Coated Carbide
655
330
AP25N
VP25N
NX2525
UC5115
UE6110
PVD Coated Carbide
VP15TF
1970
Cemented Carbide
1310
655
VP10RT VP20RT
HTi05T
Cutting Speed (SFM)
Cutting Speed (SFM)
Sintered Diamond
UC5105
985
HTi10
Cemented Carbide
HTi10
UTi20T
.008
.016
.024
Feed (inch/rev)
.032
.004
.008
.012
.016
Feed (inch/rev)
A031
TURNING INSERTS
TURNING INSERTS
COATED CARBIDE
(CVD)
State-of-the-art 2 in 1 technology
achieves high wear resistance, high
fracture resistance and high stability.
2 in 1 technology consists of
Nano-texture coating and
Black-super smooth coating.
The brous nanoscale TiCN and the
crystal growth controlled Alumina(Al2O3)
in the Nano-texture coating give far
superior fracture and wear resistance
compared to conventional coatings.
Black-super smooth coating which is
used for the periphery of the insert has
an extremely smooth surface and
provides stable cutting for prolonged
periods without abnormal damage such
as welding or chipping.
Special tough brous structure improves wear

and fracture resistance.
Cover a wide application range and thus
reduces the number of tools required.
SELECTION STANDARD
Micro Structure of Coated Carbide UE6110
TURNING
Recommended Grade
Recommended Cutting
Speed (SFM)
ISO
UE6105
1150
(655 1800)
P01
UE6110
820
(495 1315)
P10
UE6020
655
(330 820)
UE6035
490
(260 655)
Continuous
Cutting
US7020
555
(390 720)
Continuous
and
Interrupted
Cutting
US735
Continuous
Cutting
UC5105
Interrupted
Cutting
UC5115
Heat Resistant Continuous

and
Alloys
Interrupted
US905
Work Material
Cutting
Mode
P
Continuous
Cutting
Steel
Interrupted
Cutting
Application Range
P20
P30
P40
M10
M20
Stainless Steel
M30
330
(260 390)
M40
K01
985
(655 1315)
K10
Cast Iron
Ductile Cast Iron
K20
820
(490 985)
K30
260
(165 330)
S01
NEGATIVE
CUTTING CONDITIONS
Stable Cutting
Continuous Cutting
Constant Depth of Cut
Pre-Machined
Securely Clamped Component
Material
CUTTING AREA
Finish Cutting
(ap < .020inch)
St
ab
le
Cu
ttin
Carbon Steel
Alloy Steel
Light Cutting
(ap=.020 .060inch)
General Cutting
Medium Cutting
Unstable Cutting
Irregular Depth of Cut
Low Clamping Rigidity
(ap=.060 .157inch)
Semi-Heavy Cutting
Heavy Cutting
A032
Un
(ap=.157 .276inch)
(ap=.276 .394inch)
sta
1st Recommendation
(General Cutting)
ble
Cu
ttin
Grade
Substrate
Hardness (HRA) T.R.S (GPa)
Coating Layer
Composition
Surface
Thickness
UC5105
92.2
2.0
TiCN-AI2O3
UC5115
91.0
2.2
TiCN-AI2O3
Thick
Thick
UE6105
90.8
1.8
Tough
TiCN-AI2O3-Ti Compound
Thick
UE6110
90.3
2.0
Tough
TiCN-AI2O3-Ti Compound
Thick
UE6020
90.0
2.2
Tough
TiCN-Al2O3-Ti Compound
Thick
UE6035
89.5
2.3
Tough
TiCN-AI2O3-TiN
Thick
UH6400
89.5
2.3
Tough
Thick
US7020
90.5
2.0
Tough
TiCN-AI2O3-TiN
Thin
US735
89.0
2.6
Ti Compound
Thin
US905
92.2
2.0
TiCN-AI2O3
Thin
TURNING INSERTS
GRADE CHARACTERISTICS
1GPa=102kg/mm2
APPLICATION EXAMPLES
CNMG434MA (UE6110)
Insert (Grade)
WNMG432MV (UE6020)
Alloy steel
Alloy steel (Gear)
Workpiece
Cutting
Conditions
Cutting Speed (SFM)

(IPR)
Feed
Depth of Cut (inch)
Coolant
785
.012 .015
.118 .157
Wet cutting
525
.010
.079
Wet cutting
pieces/corner
pieces/corner
Result
UE6110
UE6020
Competitor's P10 coating
Competitor's P20 coating
UE6110 achieved 1.5 times longer tool life without any

abnormal wear compared to a competitor's product.
UE6020 achieved 6 times long tool life.
CNMG432MS(US7020)
Insert (Grade)
CNMA432(UC5105)
Stainless steel
Gray cast iron (Hub)
Workpiece
Cutting
Conditions
Cutting Speed (SFM)

(IPR)
Feed
Depth of Cut (inch)
Coolant
820
.012
.10
Wet cutting
Conventional coated grade=330, US7020=655
.006 .008
.08
Wet cutting
pieces/corner
Result
pieces/corner
US7020
UC5105
Previous coated grade
Competitor's K01 coating
Large wear
UC5105 achieved more than double the tool life.
US7020 achieved two times longer tool life compared

to previous grade when turning in double cutting speed.
NEGATIVE
NEGATIVE
Material
St
ab
le
Material
St
ab
Cu
HZ
US7020
ttin
HZ
le
Flat Top
Cu
UC5105
ttin
Stainless Steel
GH
US7020
Standard
UC5105
GH
US735
MS
US7020
MS
SA
US7020
SA
FH
US735
FH
US735
US735
1st Recommendation
(General Cutting)
US735
SA
US735
US735
Standard
HZ
US735
UC5115
MA
UC5105
Flat Top
MA
GH
US735
MA
UC5105
UC5115
UC5115
Standard
UC5115
MA
MS
US735
UC5115
MA
UC5115
Un
ble
Un
UC5115
sta
FH
US735
Cast Iron
Ductile Cast Iron
Flat Top
Cu
ttin
1st Recommendation
(General Cutting)
MA
UC5115
sta
ble
Cu
ttin
A033
TURNING INSERTS
TURNING INSERTS
COATED CARBIDE
(PVD)
Coating Layer
(Wear Resistance)
(Thermal Shock Resistance)
(Welding Resistance)
PVD coating prolongs tool life.

Coating of tools with sharp edges is possible without
softening or changing the quality of the substrate.
Substrate
SELECTION STANDARD
TURNING
Work Material
Coating
Name
Recommended Grade
Recommended Cutting
Speed (SFM)
ISO
VP10RT
390
(330 490)
P01
VP15TF
P10
VP20MF
390
(330 490)
390
(330 490)
VP20RT
390
(330 490)
P30
UP20M
390
(330 490)
P40
VP10RT
390
(330 490)
M01
VP15TF
M10
VP20MF
390
(330 490)
390
(330 490)
VP20RT
390
(330 490)
M30
UP20M
390
(330 490)
M40
VP10RT
390
(330 490)
K01
VP15TF
390
(330 490)
VP Coating
Steel
UP Coating
Stainless
Steel
VP Coating
UP Coating
Cast Iron
VP Coating
Heat Resistant
VP Coating
Alloy
A034
P20
M20
K10
K20
VP20RT
390
(330 490)
K30
VP05RT
165
(65 230)
S01
VP10RT
130
(65 165)
S10
VP20RT
130
(65 165)
S20
VP15TF
130
(65 165)
S30
Application Range
TURNING INSERTS
FEATURES OF VP (MIRACLE) COATING
(r)
Comparing to conventional coating technology, the VP

(MIRACLE) coating features (Al,Ti)N coating which highly
increased heat resistance and adhesion strength.
900
800
MIRACLE coating
Increased heat resistance
700
600
Increased adhesion strength
Competitor's coating grade
50
60
70
Adhesion Strength
(N)
80
DCMT32.51MV (VP15TF)
Cutting Speed (SFM)

(IPR)
Feed
Depth of Cut (inch)
Coolant
560
.006
.010
Wet cutting
650
.010
.020
Wet cutting
pieces/corner
VP15TF
Competitor's
P30 coating
VP15TF does not experience chipping.

This enables stable machining and much
longer tool life.
Insert (Grade)
CNMG432MJ (VP10RT)
Cutting
Conditions
Competitor's
K20 carbide
(M Class)
1.5times longer tool life.
TNMG332MJ (VP05RT)
Sintered iron parts (FH655)
Workpiece
Cutting Speed (SFM)

(IPR)
Feed
Depth of Cut (inch)
Coolant
Result
pieces/corner
1.5"
Inconel 718 (Pin)
M Class
MJ breaker
(VP10RT)
2.0"
Cutting
Conditions
Workpiece
1.75"
1.77"
Alloy steel
Result
CNMG432MJ (VP10RT)
Stainless Steel (Fan parts)
3.30"
Insert (Grade)
100
.008
.091
Wet cutting
MJ breaker
(VP10RT)
Competitor's
coated carbide
400
.002
.020
Wet cutting
pieces/corner
MJ breaker achieved four times longer tool life.

MJ breaker also exhibited excellent chip
disposal properties.
M Class
MJ breaker
(VP05RT)
pieces/corner
Competitor's
K10 carbide
(G Class)
5 times longer tool life.
A035
TURNING INSERTS
TURNING INSERTS
a NX3035 uses a special
CERMET
alloy substrate in the metal

binder phase to deliver
highly improved thermal
shock resistance.
The optimized alloy structure and special alloy binder

improves both wear and fracture resistance.
Cermet grades cover a wide application range and reduce
the number of tools required.
NX3035 for wet cutting.
NX2525 for dry cutting.
Micro-Structure of NX3035
a NX2525 has high
hardened Ti compound
particles within it's
microstructure therefore
the grade has both
excellent wear and fracture
resistance properties.
SELECTION STANDARD
TURNING
Work Material
Cutting
Mode
Recommended Grade
Recommended Cutting
Speed (SFM)
ISO
Continuous
Cutting
NX2525
820
(655 920)
P01
Interrupted
Cutting
NX3035
590
(330 820)
NX2525
690
(555 755)
Steel
Application Range
P10
P20
K01
Cast Iron
Finishing
Ductle Cast Iron
K10
K20
CUTTING PERFORMANCE
Cutting Speed : vc Depth of Cut : ap
Feed : f
Cutting Performance
Steel, Continuous Cutting (Wet)
Flank Wear (inch)
Competitor's P20
coated cermet
Steel, Interrupted Cutting

<Cutting Conditions>
Insert : CNMG432pp
vc=820SFM
ap=.039inch
f=.006inch/rev
Wet Cutting
External Continuous Cutting
Competitor's
micro grain
P20 cermet
Workpiece : Alloy Steel
Insert : CNMG432pp
vc=655SFM
ap=.059inch
f=.008inch/rev
Wet Cutting
Interrupted Cutting
Competitor's
micro grain
P20 cermet
Competitor's
P20 coated
cermet
Cutting Time (min)
Number of Impacts
Flank Wear (inch)
Cast Iron, Continuous Cutting
Competitor's K10
Cemented Carbide
Workpiece : AISI-40
Insert : CNMG432
vc=330SFM
ap=.059inch
f=.012inch/rev
Wet Cutting
Cutting Time (min)
Substrate
Grade
NX2525
NX3035
NX55
Hardness (HRA)
T.R.S(GPa)
92.2
91.5
91.7
2.0
2.1
1.8
Thermal Conductivity Thermal Expansion

(W/mK)
(x 10-6/K)
7.8
7.8
7.8
33
35
25
2
-3
* 1GPa=102kg/mm , 1W/m K=2.39 x 10

A036
cal/cm sec r
COATED CERMET
Outer layer is TiN

(Welding resistance)
Middle layer is (Al,Ti)N
Compound.
(wear resistance thermal
shock resistance)
Coated cermet (PVD coating) has superior wear and

fracture resistance, and therefore provides a stable
cutting performance.
Substrate
Micro Grain Cermet
NX2525 (wear resistance
and fracture resistance)
TURNING INSERTS
Coating Layer
Micro-Structure of AP25N
SELECTION STANDARD
TURNING
Work Material
Cutting
Mode
Recommended Grade
Recommended Cutting
Speed (SFM)
Continuous
Cutting
VP25N
AP25N
920
(655 1050)
Interrupted
Cutting
VP45N
590
(460 655)
ISO
Application Range
P01
P10
Steel
P20
P30
K01
Cast Iron
Finishing
Ductile Cast Iron
VP25N
AP25N
720
(555 820)
K10
K20
CUTTING PERFORMANCE
Feed : f
Cutting Performance
Thermal Shock Resistance in interrupted Cutting
Flank Wear (inch)
Competitor's
PVD Cermet A
Conventional
Cermet
Cutting Time (min)
Workpiece : AISI4140(HB230)
Insert : CNMG432oo
vc=985SFM
ap=.020inch
f=.008inch/rev
Wet Cutting
Workpiece : AISI4140(HB230)
Insert : CNMG432oo
vc=655SFM
ap=.079inch
f=.012inch/rev
Wet Cutting
Number of Passes
Wear Resistance in Wet Cutting
Competitor's Conventional
Cermet
PVD
Cermet A
A037
TURNING INSERTS
TURNING INSERTS
CEMENTED CARBIDE
Available in this range are UTi20T grades
suitable for steel and cast iron,
HTi grades for cast iron, non ferrous metal
and nonmetals, and RT grades
for heat-resistant alloys and titanium alloy.
K Class Grade (WC-Co)
SELECTION STANDARD
.394 !inch
P,M Class Grade (WC-TiC-TaC-Co)
.394 ! inch
TURNING
Work Material
Recommended Grade
Recommended Cutting
Speed (SFM)
UTi20T
330
(195 425)
ISO
Application Range
P10
Steel
P20
P30
M10
Stainless Steel
UTi20T
330
(195 425)
HTi05T
HTi10
390
(260 490)
330
(165 490)
UTi20T
330
(165 490)
M20
M30
K
Cast Iron
K01
K10
K20
K30
N01
Non-Ferrous Metal
N10
1970
(1210 2630)
HTi10
N20
N30
230
(165 330)
195
(130 260)
165
(130 230)
RT9005
Heat-resistant Alloy
Ti Alloy
RT9010
TF15
S01
S10
S20
S30
MAIN COMPONENT AND APPLICATION

Main
Component
Characteristics
WC-TiC-TaC-Co High heat resistance and rigidity.
V-T Diagram (P Grade) <Cutting Conditions> Dry
Application
Carbon steel, alloy steel, stainless steel
and cast iron
WC-Co
High rigidity and wear resistance.
Cast iron, non-ferrous metals, and non-metal
WC-Co
High heat resistance and wear resistance.
Heat-resistant alloy and Ti alloy
Cutting Speed ( SFM )
ISO
Tool Life (min)
Grade
Hardness
(HRA)
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
90.5
92.5
92.0
92.2
92.0
91.5
Thermal
Thermal
Conductivity Expansion
(W/mK)
(x10-6/K)
38
79
79
79
79
71
5.5
4.5
4.6
4.5
4.6
5.3
2
Young's
Modulus
(GPa)
T.R.S
(GPa)
520
600
630
600
630
580
2.0
1.5
2.0
2.0
2.2
2.5
-3
* 1GPa = 102kg/mm , 1W/mK=2.39 x 10

A038
cal/cm sec r
V-T Diagram (K Grade) <Cutting Conditions> Dry

Cutting Speed (SFM )
ISO
Workpiece:AISI1045 (220HB)
Tool Life Standard:VB=.012inch
Depth of Cut:.059inch
Feed:.012inch/rev
Holder:CSBNR2525M43
Insert:SNMG432
Workpiece:AISI40
Tool Life Standard:VB=.012inch
Depth of Cut:.059inch
Feed:.012inch/rev
Holder:CSBNR2525M43
Insert:SNMN432
Tool Life (min)
TURNING INSERTS
MICRO-GRAIN
CEMENTED CARBIDE
Compared to general cemented carbide,
micro-grain alloy has higher wear resistance and higher toughness.
Micro-Structure of TF15
.079!inch
SELECTION STANDARD
Cutting Tool
Recommended Grade
Work Material
Turning Inserts
Milling Inserts
TF15
Steel Cast Iron

Ti Alloy
Grade Characteristics
Grade
Specic Gravity Hardness (HRA) T.R.S (Gpa)
TF15
* 1GPa=102kg/mm
14.5
91.5
2.5
ISO
Wear
Resistance
Fracture
Resistance
Corrosion
Resistance
K20
A039
CLASSIFICATION
Breaker Name
and
Picture
Cross Section
Geometry
Features
First recommendation for nishing carbon steel,
alloy steel and stainless steel
Double sided chipbreaker.
Stable chip control even at small depth of cut.
Nose

12
ap (inch)
Application
Tolerance
TURNING INSERTS
TURNING INSERTS
Flank
12
Alternative breaker for nishing mild steel
Mild Steel

Sharp edge gives best performance.
ap (inch)
M Class
f (inch/rev)
Nose
16
Flank
8
First recommendation for nishing mild steel

Effectively controls chips.
Suitable for mild steel nishing.
ap (inch)
f (inch/rev)
Mild Steel
Nose
15
Flank
.008"
15
f (inch/rev)
Flank
9
First recommendation for nishing titanium alloy
Titanium alloy

Ideal for aluminum and copper.
The sharp edge produces excellent surface nishes.
The curved edge allows smooth chip discharge.
The polished insert face prevents built up edge.
ap (inch)
f (inch/rev)
Alternative breaker for nishing carbon steel and

alloy steel
Flank
9
f (inch/rev)
Nose
ap (inch)
15
Flank
15
f (inch/rev)
Precise nishing

A narrow angled chipbreaker for good control.
The sharp edge produces a good surface nish.
ap (inch)

G class insert tolerance is suitable for workpieces requiring close
dimensional tolerances.
Nose
14
Finishing

Angled chipbreaker controls chip ow.
The sharp edge produces a good chip discharge.
ap (inch)
G Class
Finish Cutting

Ideal for heat-resistant alloy.
The sharp edge produces good cutting surface.
Nose
14
ap (inch)
First recommendation for nishing difcult-to-cut

materials
Alternative breaker for light cutting of carbon steel

and alloy steel
Flank
14
f (inch/rev)
Flank
14
A040

Superior chip control at small depth of cuts.
Covers copying and back turning with wavy edge.
Recommended for workpieces in the 200 300HB range.
Nose
.012"
25
ap (inch)
Light Cutting
M Class
f (inch/rev)
10
Flank
.013"
25
f (inch/rev)
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
TURNING INSERTS
Rhombic 80
A041
CLASSIFICATION
Breaker Name
and
Picture
Cross Section
Geometry
Features
First recommendation for light cutting of carbon steel,
Nose
15
Flank
.008"
15
f (inch/rev)
Wiper insert for light cutting of carbon steel and alloy steel

The wiper allows up to two times higher feed.
Wiper design for increased productivity and improved surface nish.
ap (inch)

Can be used at low depth of cuts and high feed rates.

ap (inch)
Application
Tolerance
TURNING INSERTS
TURNING INSERTS
Nose
.006"
18
7
Flank
.006"
18
7
f (inch/rev)
10
Flank
10
.008"
f (inch/rev)
Alternative breaker for light cutting of carbon steel

and alloy steel
Can be used at small depth of cuts.
Nose

12
ap (inch)
M Class

Effectively controls chips.
Nose
Mild Steel
ap (inch)
First recommendation for light cutting of mild steel
Flank
12

Excellent chip control at low to medium feed rates.

Flank
ap (inch)
Light Cutting
f (inch/rev)
Alternative chipbreaker for light cutting of carbon steel

and alloy steel
15
.008"
f (inch/rev)


Flank
ap (inch)
Alternative chipbreaker for light cutting of carbon steel

and alloy steel
15
.008"
Light cutting

Parallel chipbreaker.
ap (inch)
G Class
f (inch/rev)
First recommendation for light cutting of

difcult-to-cut materials
Flank
14
.010"
A042
Nose
13
ap (inch)

Ideal for heat-resistant alloy and titanium alloy.
Flank
9
f (inch/rev)
First recommendation for light cutting of difcult-to-cut materials
Double sided chipbreaker, Single sided chipbreaker.

G class insert tolerance is suitable for workpieces requiring close
dimensional tolerances.
ap (inch)
G Class
M Class
f (inch/rev)
Nose
13
Flank
9
f (inch/rev)
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
TURNING INSERTS
Rhombic 80
A043
CLASSIFICATION
Breaker Name
and
Picture
Cross Section
Geometry
Features
First recommendation for medium cutting of carbon
steel and alloy steel
First recommendation for nish to light cutting of
cast iron

ap (inch)
Application
Tolerance
TURNING INSERTS
TURNING INSERTS

Positive land provides sharp cutting action.
First recommendation for medium-heavy cutting of mild steel

Alternative breaker for medium cutting of carbon steel and
alloy steel
Flat land offers high edge strength.
A wide chip pocket prevents chip jamming at large depth of cut.
First recommendation for medium cutting of cast iron

Alternative breaker for medium cutting of carbon steel
and alloy steel
ap (inch)
Flank
f (inch/rev)
Nose
Flank
f (inch/rev)
Nose
Flank
f (inch/rev)
Wiper insert for medium cutting carbon steel and

alloy steel
A wide chip pocket prevents chip jamming.
Nose
ap (inch)
Medium Cutting
M Class

Flat land offers high edge strength.
Nose
Flank
f (inch/rev)
First recommendation for medium cutting of

stainless steel, mild steel and difcult-to-cut
materials
The sharp edge gives best performance.
Stainless Steel
ap (inch)
Standard
f (inch/rev)
ap (inch)

Suitable for medium to light cutting.
Breaker geometry appropriate for copying and back turning.
Good balance of sharpness and strength.
Flank
ap (inch)
Alternative breaker for medium cutting of carbon

steel and alloy steel
Nose
Nose
Flank
f (inch/rev)

Good balance of edge strength and sharpness.
Right- or left-hand breaker for unidirectional chip control.
Flank
ap (inch)
Alternative chipbreaker for medium cutting of

stainless steel
Stainless Steel
f (inch/rev)

carbon steel and alloy steel
Parallel chipbreaker controls chip ow.
Good chip control for medium feed rates.
ap (inch)

Parallel chipbreaker controls chip ow.
Good chip control for medium feed rates.
Molded chipbreaker.
Flank
f (inch/rev)
Flank
ap (inch)

f (inch/rev)
A044
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
TURNING INSERTS
Rhombic 80
A045
CLASSIFICATION
Breaker Name
and
Picture
Cross Section
Geometry
Features

ap (inch)
Flank

Good chip control for medium feed rate.
First recommendation for semi-heavy cutting of

carbon steel, alloy steel and stainless steel
Nose
ap (inch)
Medium cutting
Flank
f (inch/rev)

For interrupted cut and removing scale.
A combination of wide land and large chip pocket allows high feeds.
f (inch/rev)

difcult-to-cut materials
Excellent balance of edge sharpness and strength.
Edge geometry with high face wear resistance.
ap (inch)
Medium Cutting Application

G Class
Tolerance
Semi-heavy Cutting
M Class
TURNING INSERTS
TURNING INSERTS
Nose
Flank
f (inch/rev)
Heavy Cutting
M Class
Alternative chipbreaker for heavy cutting of

Single sided chipbreaker.
Appropriate for the upper end of the heavy cutting region.
Wide land and large chamfer offer high edge strength.
A wide chipbreaker prevents chip jamming.
Alternative chipbreaker for heavy cutting of

Appropriate for the lower end through to the medium range of the heavy cutting region.
Due to the variable land, provide a balance of sharpness and strength.
A narrow chipbreaker for good chip control.
Alternative chipbreaker for heavy cutting of mild

steel and stainless steel
Appropriate for the lower end through to the medium range of the heavy cutting region.
The narrow chamfer and variable land provide a balance between
sharpness and strength.
A046
ap (inch)
Nose
ap (inch)

Appropriate for the medium range of the heavy cutting region.
The at edge and chamfer, provide a balance of sharpness and strength.
Variable land and a wavy chipbreaker for good chip control.
f (inch/rev)
Flank
f (inch/rev)
Nose
ap (inch)
First recommendation for heavy cutting of

Flank
Flank
f (inch/rev)
Nose
ap (inch)

Appropriate for the lower end of the heavy cutting region.
Low cutting resistance due to positive land and curved edge.
Teardrop dots improve chip control without increasing cutting resistance.
Nose
Flank
f (inch/rev)
Mild Steel
Nose
ap (inch)
First recommendation for heavy cutting of mild steel

and stainless steel
Mild Steel
Flank
f (inch/rev)
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
TURNING INSERTS
Rhombic 80
A047
CLASSIFICATION
A048
Breaker Name
and
Picture

cast iron
Double sided at insert.
Most effective in unstable machining i.e. interrupted cuts due to
high edge strength and stable tting on the shim.
Cast Iron
ap (inch)
Flat Top
Cross Section
Geometry
Features
f (inch/rev)
Flat Top
For cast iron
Cast Iron

Most effective in unstable machining i.e. interrupted cuts due to
high edge strength and stable tting on the shim.
Can be used on workpieces requiring close tolerances due to G
class.
ap (inch)
Application
Tolerance
For Cast Iron

M Class
G Class
TURNING INSERTS
TURNING INSERTS
f (inch/rev)
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
TURNING INSERTS
Rhombic 80
A049
CLASSIFICATION
Breaker Name
and
Picture
Cross Section
Geometry
Features
alloy steel, mild steel and stainless steel
Suitable for low depth of cut and feed rate applications.
Sharp cutting edge and low resistance design provide excellent cutting
performance.
Nose
ap (inch)
Application
Tolerance
5 POSITIVE INSERTS WITH HOLE
M Class
TURNING INSERTS
TURNING INSERTS
Flank
Finishing difcult-to-cut materials
Nose
The curved cutting edges support changes in cutting depth-smooth

The high rake angle is highly suitable for finishing diffcult-to-cut
materials.
ap (inch)
Flank
Finishing titanium alloy
Titanium alloy
Nose

ap (inch)
Finish Cutting
G Class
f (inch/rev)
Flank
Finishing carbon steel and alloy steel
f (inch/rev)
f (inch/rev)
ap (inch)
Light cutting of carbon steel, alloy steel, mild steel

and stainless steel
Nose
ap (inch)
Flank

Sharp cutting edge produces excellent surface nishes.
Flank
f (inch/rev)
The double breaker design promotes chip discharge for mild steel
low depth of cut a applications.
Nose
Flank
f (inch/rev)
Light cutting for titanium alloy
Titanium alloy
Nose

ap (inch)

The high rake angle is highly suitable for nish-light cutting difcultto-cut materials.
ap (inch)
Light cutting of difcult-to-cut materials

Ideal for heat-resistant alloy and titanium alloy
Flank
Medium cutting of carbon steel, alloy steel,

mild steel and stainless steel
Nose
ap (inch)
Light Cutting
G Class
f (inch/rev)
Flank
A050
A positive land and the high rake angle provides sharp cutting edge
performance.
The double breakers and round-shaped dots in the rake face
provide a wide range of chip control.
Medium cutting of carbon steel, alloy steel,

mild steel and stainless steel
performance.
The double breakers and round-shaped dots in the rake face
provide a wide range of chip control.
f (inch/rev)
Nose
ap (inch)
Medium Cutting
M Class
f (inch/rev)
Flank
f (inch/rev)
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
TURNING INSERTS
Rhombic 80
A051
CLASSIFICATION
Nose
The high rake angle combined with a small flat land provide a
balance of strength and sharpness.
ap (inch)
Flank
Medium cutting of Swiss type lathe machining
Features a high angled chipbreaker.

Low resistance insert design controls chip ow.
ap (inch)
Standard
Cross Section
Geometry
Features
General purpose of Swiss type lathe machining
The parallel chipbreaker.

Excellent chip control for low to midium feed rates.
ap (inch)
Breaker Name
and
Picture
General purpose of Swiss type lathe machining

Excellent chip control for low to medium feed rates.
The wiper produces good surface nishes.
ap (inch)
Application
Tolerance
M Class
TURNING INSERTS
TURNING INSERTS
Medium cutting of carbon steel, alloy steel and

stainless steel
Medium Cutting
E Class
f (inch/rev)
Flank
30
f (inch/rev)
Flank
20
f (inch/rev)
20
f (inch/rev)
A052
Flank
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
TURNING INSERTS
Rhombic 80
A053
CLASSIFICATION
Breaker Name
and
Picture
Cross Section
Geometry
Features
alloy steel and mild steel
Sharp cutting edge and low resistance design provides excellent
cutting performance.
Suitable for low depth of cut and feed rate applications.
Nose
ap (inch)
Application
Tolerance
M Class
TURNING INSERTS
TURNING INSERTS
Flank
First recommendation for nishing difcult-to-cut

materials
Flank
Finishing titanium alloy
Nose
Ideal for copper.

ap (inch)
f (inch/rev)
Titanium alloy
Flank
For aluminium alloy
Aluminum Alloy
The high rake angle and 3D curved cutting edge provides sharpness at the
cutting point.
Additionally the 3D shape of the rake face enables excellent chip control.
ap (inch)
The curved cutting edges support changes in cutting depth and

allow smooth chip discharge and disposal.
The high rake angle is highly suitable for finishing diffcult-to-cut
materials.
Nose
ap (inch)
f (inch/rev)
Finish Cutting
G Class
f (inch/rev)
Flank
f (inch/rev)

Sharp cutting edge provides excellent surface nishes.
Flank
ap (inch)
f (inch/rev)
ap (inch)
Flank
Angled chipbreaker.
Excellent chip control at low feed rates.
Alternative chipbreaker for light cutting of carbon steel,

Nose
The double breaker design promotes chip control in mild steel and
low depth of cut machining applications.
ap (inch)
Flank
Light cutting of carbon steel and alloy steel
Nose
Breaker geometry appropriate for copying.

Excellent chip control.
ap (inch)
Finishing
Flank
Light Cutting
M Class
f (inch/rev)
f (inch/rev)
f (inch/rev)
A054
Trigon 80
Rhombic 25
Round
TURNING INSERTS
Rhombic 80 Rhombic 55 Square 90 Triangular 60 Rhombic 35
A055
CLASSIFICATION
Breaker Name
and
Picture
Cross Section
Geometry
Features
Wiper insert for light cutting of carbon steel, alloy
steel, mild steel and stainless steel
Positive land improves sharpness.
Nose

20
ap (inch)
Application
Tolerance
M Class
TURNING INSERTS
TURNING INSERTS
12
Flank
16
Light cutting for Swiss type lathe machining

Excellent chip control at low feed rate.
ap (inch)
Light cutting of difcult-to-cut materials

Ideal for heat-resistant alloy and titanium alloy
.005"
8
f (inch/rev)
Light Cutting
G Class
.005"
Flank
14
f (inch/rev)
ap (inch)
Flank
9
f (inch/rev)
Light cutting for titanium alloy
Titanium alloy
Ideal for copper.

ap (inch)

The high rake angle is highly suitable for nishlight cutting difcultto-cut materials.
Nose
13
First recommendation for medium cutting of carbon steel,

alloy steel, mild steel, stainless steel and cast iron
Nose
13
Flank
9
f (inch/rev)
The high rake angle combined with a small, flat land provide a
balance of strength and sharpness.
Nose
.004"
18
ap (inch)
Standard
Flank
18
.004"
f (inch/rev)
performance.
The double breakers and round-shaped in the rake face provide a
wide range of chip control.
Wiper insert for medium cutting of carbon steel,

A wide chip pocket prevents chip jamming.
Nose
.007"
20
ap (inch)
Alternative chipbreaker for medium cutting of carbon steel,

12
Flank
.007"
20
12
f (inch/rev)
Nose

18
ap (inch)
Medium Cutting
M Class
.008"
15
.008"
7
Flank
.008"
18
f (inch/rev)
A056
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
TURNING INSERTS
Rhombic 80
A057
CLASSIFICATION
Breaker Name
and
Picture
Cross Section
Geometry
Medium cutting for Swiss style lathes machining
The wide angled chipbreaker.

Low resistance insert design controls chip ow.
ap (inch)
General purpose for Swiss style lathes machining

ap (inch)

ap (inch)
Features

The wiper produces good surface nish.
ap (inch)
Application
Tolerance
E Class
TURNING INSERTS
TURNING INSERTS
Flank
30
f (inch/rev)
Flank
20
Medium Cutting
G Class
f (inch/rev)
Flank
20
E Class
f (inch/rev)
Flank
20
3D molded chipbreaker provides good chip control.

G class insert gives sharp cutting action,
allowing high precision machining.
Nose
13
ap (inch)
G Class
f (inch/rev)
Flank
10
Heavy cutting of carbon steel and alloy steel
A wide groove chipbreaker prevents chips

from jamming at large depths of cut.
Small dimples improve chip control at small depths of cut.
ap (inch)
Heavy cutting of mild steel and stainless steel
Mild Steel
A wide groove chipbreaker and a sharp angle

chipbreaker wall controls chips.
Large chamfer provides high edge strength.
ap (inch)
For cast iron
Cast Iron
Most effective in unstable machining due to high edge strength.
ap (inch)
For cast iron
Cast Iron

Can be used on workpieces requiring close tolerances due to
G class.
ap (inch)
Heavy Cutting
M Class
f (inch/rev)
28
f (inch/rev)
.011"
10
For Cast Iron

M Class
G Class
f (inch/rev)
Flat Top
f (inch/rev)
Flat Top
f (inch/rev)
A058
.012"
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
TURNING INSERTS
Rhombic 80
A059
CLASSIFICATION
Breaker Name
and
Picture
Cross Section
Geometry
Features
Suitable for low depths of cut and low feed rate applications.
Sharp cutting edge and low resistance design achieves excellent cutting
performance.
Nose
ap (mm)
Application
Tolerance
M Class
TURNING INSERTS
TURNING INSERTS
Flank
f (mm/rev)
Flank
15

ap (inch)
f (inch/rev)

ap (inch)
M Class
Small angled chipbreaker.

ap (inch)
G Class

alloy steel, stainless steel, cast iron and aluminum
alloy
Finishing carbon steel, alloy steel and stainless steel
Copper
Flank
15
G Class
f (inch/rev)
Flank
15
ap (inch)
For small depth of cut and low feed.
Nose
Flank
6
Light cutting of carbon steel and alloy steel
Angled chipbreaker.
Good chip control for low to medium feed rates.
ap (inch)
Finishing aluminum alloy
Aluminum Alloy
Lead chipbreaker controls chip ow.

ap (inch)
Finishing

ap (inch)
f (inch/rev)
Finishing
Lead chipbreaker controls chip ow.

ap (mm)
G Class
Finish Cutting
M Class
f (inch/rev)
Flank
10
f (inch/rev)
Standard
Flank
25
M Class
f (inch/rev)
Flank
10
E Class
f (inch/rev)
f (mm/rev)
A060
Flank
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
TURNING INSERTS
Rhombic 80
A061
CLASSIFICATION
Breaker Name
and
Picture
Cross Section
Geometry
Nose
3D molded chipbreaker provides good chip control.

G class insert gives sharp cutting action,
allowing high precision machining.
ap (mm)
Flank
First recommendation for light cutting of carbon steel,

Nose
ap (inch)
Features
Flank
The double breaker design promotes chip discharge for mild steel
and low depth of cut machining applications.
Medium Cutting
M Class
performance.
Double breakers in the rake face achieve a wide range of chip
control.
Medium cutting of carbon steel, alloy steel and

stainless steel
Can be used under a wide range of cutting conditions.
Nose
Flank
f (inch/rev)
Copper
Nose
ap (inch)
First recommendation for medium cutting of carbon steel,

ap (inch)
f (inch/rev)
Flank
f (inch/rev)
Standard
Alternative chipbreaker for medium cutting of carbon steel,

Standard, general purpose chipbreaker.
Nose
ap (inch)
Light Cutting Finish Cutting Application

M Class
Tolerance
G Class
TURNING INSERTS
TURNING INSERTS
Flank
Heavy cutting of cast iron
Cast Iron
Flat top.
Most effective for unstable machining due to high edge strength.
ap (inch)
Flat Top
f (inch/rev)
Flat Top
For cast iron
Cast Iron

Can be used on workpieces requiring close tolerances due to G
class insert tolerance.
ap (inch)
For Cast Iron

M Class
G Class
f (inch/rev)
f (inch/rev)
A062
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
TURNING INSERTS
Rhombic 80
A063
CLASSIFICATION
Breaker Name
and
Picture
Cross Section
Geometry
For aluminum cutting
Aluminum Alloy
Angled chipbreaker.
ap (inch)
Features
Flank
20
f (inch/rev)
Aluminum Alloy
Angled chipbreaker.
Flank
ap (inch)
20
f (inch/rev)
Aluminum Alloy

Flank
ap (inch)
Application
Tolerance
15 20 POSITIVE INSERTS WITH HOLE
For Aluminum Alloy

G Class
TURNING INSERTS
TURNING INSERTS
25
f (inch/rev)
A064
Breaker Name
and
Picture
Standard
Cross Section
Geometry
Features
For difcult-to-cut materials
ap (inch)
G Class
For Difcult-to-cut
Materials
Application
Tolerance
f (inch/rev)
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
Rhombic 80
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
CHIPBREAKER SYSTEM
A040
TURNING INSERTS
Rhombic 80
A065
CLASSIFICATION
Breaker Name
and
Picture

Most effective for unstable machining due to high edge
strength and stable insert clamping.
Flat Top
Flank
ap (inch)
.012"
12
f (inch/rev)
Cast Iron
0
ap (inch)
f (inch/rev)
Cast Iron
For cast iron

Use on workpieces requiring close tolerance inserts.
ap (inch)
For Cast Iron

M Class
G Class

Can be used for copying.
A parallel chipbreaker for good chip discharge. (M2)
An angled chipbreaker for controlling chip ow. (M1)
Flat Top
Cross Section
Geometry
Features
Medium cutting of carbon steel and alloy steel
M Class
Application
Tolerance
Semi-Heavy
Cutting
TURNING INSERTS
TURNING INSERTS
f (inch/rev)
Breaker Name
and
Picture
Flat Top
Cross Section
Geometry
Features
For cast iron
Cast Iron

ap (inch)
For Cast Iron Application

G Class Tolerance
7 POSITIVE INSERTS WITHOUT HOLE
f (inch/rev)
A066
Breaker Name
and
Picture
Finishing
A parallel chipbreaker.
ap (inch)
Light to medium cutting of carbon steel, alloy steel

and stainless steel
Standard, general purpose chipbreaker.
Flank
15
f (inch/rev)
Nose
0
ap (inch)
Standard
Cross Section
Geometry
Features
Flank
0
Flat Top
Cast Iron
Flat top.
ap (inch)
f (inch/rev)
For cast iron
Cast Iron
Flat top.
ap (inch)
M Class
For Cast Iron

M Class
G Class
Light to
Medium Cutting
Finish Cutting Application

G Class Tolerance
f (inch/rev)
Flat Top
f (inch/rev)
Triangular 60
TURNING INSERTS
Square 90
Parallelogram 55
Triangular 60
Triangular 60
Application
Tolerance
Square 90
Tool Holder Type
Special
G Class
SPECIAL PURPOSE INSERTS
TL Type
Inserts
A067

Mild Steel
Finish Cutting
Medium Cutting
Light Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
FH

Heavy Cutting
Semi-Heavy Cutting
Cast Iron (<350MPa)

Flat Top
Depth of Cut (inch)
CN
Size
Depth of Cut (inch)
TURNING INSERTS
80
CNMG 4 3 0.5
TYPE INSERTS
WITH HOLE
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Finish
Cutting
FS
Carbide
CNMG430.5FH
431FH
432FH
433FH
CNMG120402-FH
120404-FH
120408-FH
120412-FH
.008
a a
a a
.016
a s
sa
.031
a s
sa
CNMG431FS
432FS
CNMG120404-FS
120408-FS
.016
.031
CNMG431FY
432FY
CNMG120404-FY
120408-FY
.016
.031
CNGG43V5FJ
430.2FJ
430.5FJ
431FJ
432FJ
CNGG43V5FJ-P
430.2FJ-P
430.5FJ-P
CNGG1204V5-FJ
120401-FJ
120402-FJ
120404-FJ
120408-FJ
CNGG1204V5-FJ-P
120401-FJ-P
120402-FJ-P
.002
.004
.008
.016
a s
.031
a a
CNGG431PK
432PK
CNGG120404-PK
120408-PK
.016
.031
.047
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
Finish
Cutting
FY
C006
009
E021
E024
H006
008
Finish
Cutting
FJ
Finish
Cutting
FJ-P
PK
A068
a s
a
.004
.008
Finish
Cutting

a
r
ss
.002
Finish
Cutting
Applicable
Holder Page
(inch)
FH
Unstable Cutting
Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Feed (inch/rev)
Feed (inch/rev)
Stable Cutting
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
(ISO) Number
(inch)
Light
Cutting
SH
Light
Cutting
SW
(With Wiper)
*
*
*
Carbide
CNMG431SA
432SA
433SA
542SA
543SA
CNMG321SH
322SH
32.51SH
32.52SH
431SH
432SH
433SH
CNMG431SW
432SW
433SW
CNMG120404-SA
120408-SA
120412-SA
160608-SA
160612-SA
CNMG090304-SH
090308-SH
09T304-SH
09T308-SH
120404-SH
120408-SH
120412-SH
CNMG120404-SW
120408-SW
120412-SW
.016
a a a
a a
.031
a a a
a a
.047
a a a
CNMG431SY
432SY
CNMG120404-SY
120408-SY
.016
.031
CNMG431C
432C
433C
CNMG120404-C
120408-C
120412-C
.016
sa
.031
sa
CNMG431MJ
432MJ
433MJ
434MJ
CNMG120404-MJ
120408-MJ
120412-MJ
120416-MJ
.016
a a
r a
.031
a a
r a
.047
ss
.063
ss
CNGG431MJ
432MJ
CNGG120404-MJ
120408-MJ
.016
a a
a s
.031
a a
a s
.031
.047
a r
.016
.031
.016
a a s
.031
a a s
.047
a a s
.016
a a
.031
.047
sa
sa
sa
sa
a a
sa
a a
C006
009
E021
E024
H006
008
a a
C006
009
E021
E024
H006
008
Light
Cutting
.047
C006
009
E021
E024
H006
008
Light
Cutting
MJ
Light
Cutting
MJ
WITH
HOLE
C006
009
E021
E024
H006
008
Light
Cutting
SY
NEG
C006
009
E021
E024
H006
008
.031
.016
Applicable
Holder Page
Order Number
SA
Unstable Cutting
Stainless Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
Light
Cutting
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
CHIP BREAKER
A040
IDENTIFICATION
A002
A069

Mild Steel
Finish Cutting
Medium Cutting
Light Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
Size Thickness Corner Radius Chip Breaker

Semi-Heavy Cutting
Heavy Cutting
Cast Iron (<350MPa)
Depth of Cut (inch)
CN
Depth of Cut (inch)
TURNING INSERTS
80
CNMG 4 3 1 MA
TYPE INSERTS
WITH HOLE
Flat Top
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Feed (inch/rev)
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
(inch)
MA
Medium
Cutting
MP
Medium
Cutting
MH
Medium
Cutting
A070
CNMG431MA
432MA
433MA
434MA
542MA
543MA
544MA
643MA
644MA
CNMG431MP
432MP
433MP
434MP
542MP
543MP
544MP
CNMG431MH
432MH
433MH
434MH
542MH
543MH
544MH
643MH
644MH
CNMG120404-MA
120408-MA
120412-MA
120416-MA
160608-MA
160612-MA
160616-MA
190612-MA
190616-MA
CNMG120404-MP
120408-MP
120412-MP
120416-MP
160608-MP
160612-MP
160616-MP
CNMG120404-MH
120408-MH
120412-MH
120416-MH
160608-MH
160612-MH
160616-MH
190612-MH
190616-MH
.016
a a a s
a a
a a
.031
a a a a
a a
a a
.047
a a a a
a a
a a
.063
a a ss
ss
a a
.031
a a a a
r s
.047
a a a a
a a
a a
.063
a a
r a
a a
.047
a a a a
a a
a a
.063
a a a
r a
a a
.016
a a a
.031
a a a
.047
a a a
.063
a a a
.031
a a a
.047
a a a
.063
a a a
.016
a a a s
.031
a a a a
.047
a a a a
.063
a a a
.031
a s
.047
a a ss
.063
a s
.047
a a s a
.063
a a a

a
r
Carbide
Applicable
Holder Page
Coated
Shape
Feed (inch/rev)
Unstable Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Stable Cutting
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
s
a
s
s
C006
009
E021
E024
H006
008
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
(inch)
Standard
Medium
Cutting
MW
(With Wiper)
CNMG322
32.51
32.52
431
432
433
434
542
543
544
642
643
644
646
CNMG432MW
433MW
CNMG090308
09T304
09T308
120404
120408
120412
120416
160608
160612
160616
190608
190612
190616
190624
CNMG120408-MW
120412-MW
.031
.016
.031
CNMG321MS
322MS
32.51MS
32.52MS
431MS
432MS
433MS
434MS
541MS
542MS
543MS
643MS
644MS
CNMP432
CNMG090304-MS
090308-MS
09T304-MS
09T308-MS
120404-MS
120408-MS
120412-MS
120416-MS
160604-MS
160608-MS
160612-MS
190612-MS
190616-MS
CNMP120408
.016
Carbide
a a s a
a a
sa
.031
a a a a
a a
sa
.047
a a a s
a a
sa
.063
a a
ss
.031
a a s r
.047
a a s a
a a
.063
a a s a
ss
.031
a a a s
.047
a a a a
a a
.063
a a s a
ss
r
a
.094
.031
a a a
a a
.047
a a a
a a
Medium
Cutting
.031
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
Medium
Cutting
MS
NEG
WITH
HOLE
.016
Applicable
Holder Page
Coated
Shape
Unstable Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
r a
a
.016
r a
r s
.031
r s
.016
a a
a a a
a a a a
s r as
.031
a a
a a a
a a a a
s r as
.047
a r
a a a
s a as
r ss
.063
r r
.016
r r
.031
r s
.047
r a
.047
r a
.063
r a
.031
s
s
C006
009
E021
E024
H006
008
Medium
Cutting
C006
009
E021
E024
H006
008
*Please refer to page A028 before using the MW breaker (wiper insert).
CHIP BREAKER
A040
IDENTIFICATION
A002
A071

Mild Steel
Finish Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Medium Cutting
Light Cutting
Depth of Cut (inch)
Semi-Heavy Cutting
Heavy Cutting
Cast Iron (<350MPa)
Depth of Cut (inch)
CN
GH

Depth of Cut (inch)
TURNING INSERTS
80
CNMG 4 3 2
TYPE INSERTS
WITH HOLE
Flat Top
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Feed (inch/rev)
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Semi-Heavy
Cutting
GJ
Semi-Heavy
Cutting
HZ
Heavy
Cutting
HX
Heavy
Cutting
A072
CNMG432GH
433GH
434GH
543GH
544GH
643GH
644GH
CNMG432GJ
433GJ
434GJ
543GJ
643GJ
644GJ
CNMM432HZ
433HZ
543HZ
544HZ
643HZ
644HZ
646HZ
CNMM543HX
544HX
643HX
644HX
646HX
856HX
858HX
866HX
868HX
CNMG120408-GH
120412-GH
120416-GH
160612-GH
160616-GH
190612-GH
190616-GH
CNMG120408-GJ
120412-GJ
120416-GJ
160612-GJ
190612-GJ
190616-GJ
CNMM120408-HZ
120412-HZ
160612-HZ
160616-HZ
190612-HZ
190616-HZ
190624-HZ
CNMM160612-HX
160616-HX
190612-HX
190616-HX
190624-HX
250724-HX
250732-HX
250924-HX
250932-HX
.031
a a a a
a a
a a
.047
a a a a
a a
a a
.063
a s
.047
a a a a
.063
a a
.047
.063
C006
009
E021
E024
H006
008
a a
a a
a a
a a a a
a a
a a
a a s a
a a
a a
a a
.031
a a
a s
.047
a a
a s
.063
ss
ss
.047
.047
.063
.031
a a
r r
.047
a a
r r
.047
a a
r r
.063
a s
r r
.047
a a
s r r
.063
a a
s r r
.094
a r
.047
a r r
.063
a r r
.047
a s r s
.063
a s r s
.094
a s r s
.094
s r s
.126
r r s
.094
a s r s
.126
r r s

a
r
Carbide
Applicable
Holder Page
(inch)
GH
Feed (inch/rev)
Unstable Cutting
Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Stable Cutting
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
C007
009
E024
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Heavy
Cutting
HAS
Coated
Cermet Cermet
CNMM644HV
646HV
856HV
866HV
CNMM190616-HV
190624-HV
250724-HV
250924-HV
CNMG866HAS
CNMG250924-HAS .094
.063
a a r s
.094
a a r s
.094
s r s
.094
a a r s
Carbide
Applicable
Holder Page
(inch)
HV
Unstable Cutting
Stainless Steel
Coated
Shape
General Cutting
Steel
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
TURNING INSERTS
P
M
K
N
S
NEG
C007
009
E024
WITH
HOLE

Heavy
Cutting
HXD
Heavy
Cutting
Flat Top
CNMM643HXD
644HXD
646HXD
866HXD
CNMM190612-HXD
190616-HXD
190624-HXD
250924-HXD
.047
.063
.094
.094
CNMA431
432
433
434
543
544
643
644
CNMA120404
120408
120412
120416
160612
160616
190612
190616
.016
a a
s a
.031
a a
ss a
.047
a a
r ss
.063
a a
.047
a a
.063
a a
.047
a a
.063
a a
C007
009
E024
C006
009
E021
E024
H006
008
CHIP BREAKER
A040
IDENTIFICATION
A002
A073
Mild Steel
Finish Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Medium Cutting
Light Cutting
Depth of Cut (inch)
Heavy Cutting
Semi-Heavy Cutting
Cast Iron (<350MPa)

Flat Top
Depth of Cut (inch)
TURNING INSERTS
FH

Depth of Cut (inch)
DN
55
DNMG 4 3 0.5
TYPE INSERTS
WITH HOLE
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Stable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Finish
Cutting
FS
DNMG430.5FH
431FH
432FH
440.5FH
441FH
442FH
DNMG431FS
432FS
DNMG150402-FH
150404-FH
150408-FH
150602-FH
150604-FH
150608-FH
DNMG150404-FS
150408-FS
.008
a a
a a
.016
a s
sa
.031
a s
sa
DNMG431FY
432FY
441FY
442FY
Carbide
C010
012
E021
E024
H009
011
.008
a s
ss
.016
ss
ss
.031
ss
ss
.016
.031
DNMG150404-FY
150408-FY
150604-FY
150608-FY
.016
.031
.016
.031
DNGG431FJ
432FJ
DNGG150404-FJ
150408-FJ
.016
ss
ss
.031
a a
a s
DNGG431PK
432PK
DNGG150404-PK
150408-PK
.016
.031
DNMG431SA
432SA
433SA
441SA
442SA
443SA
DNMG150404-SA
150408-SA
150412-SA
150604-SA
150608-SA
150612-SA
.016
a a a
a a
.031
a a a
a a
.047
a a a
C010
012
E021
E024
H009
011
Finish
Cutting
FY
Finish
Cutting
FJ
Finish
Cutting
PK
Light
Cutting
A074
.016 s s s
.031 s s s
.047 s s s

a
r
C010
012
E021
E024
H009
011
C010
012
E021
E024
H009
011
C010
012
E021
E024
H009
011
Finish
Cutting
SA
Applicable
Holder Page
(inch)
FH
Unstable Cutting
Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Feed (inch/rev)
Feed (inch/rev)
C010
012
E021
E024
H009
011
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
(ISO) Number
(inch)
Light
Cutting
SW
(With Wiper)
Light
Cutting
SY
Light
Cutting
Light
Cutting
MJ
Light
Cutting
MJ
*
*
*
*
*
*
*
*
Carbide
DNMG331SH
332SH
431SH
432SH
433SH
441SH
442SH
443SH
DNMX331SW
332SW
431SW
432SW
433SW
441SW
442SW
443SW
DNMG431SY
432SY
441SY
442SY
DNMG110404-SH
110408-SH
150404-SH
150408-SH
150412-SH
150604-SH
150608-SH
150612-SH
DNMX110404-SW
110408-SW
150404-SW
150408-SW
150412-SW
150604-SW
150608-SW
150612-SW
DNMG150404-SY
150408-SY
150604-SY
150608-SY
.016
a a
.031
a a
.016
a a s
s a
.031
a a s
s a
.047
a a s
s a
.016 s s
.031 s s
.047 s s
s a
s a
DNMG431C
432C
441C
442C
DNMG150404-C
150408-C
150604-C
150608-C
.016
s a
.031
s a
.016
s s
.031
s s
DNMG431MJ
432MJ
433MJ
434MJ
441MJ
442MJ
443MJ
444MJ
DNGM431MJ
432MJ
DNMG150404-MJ
150408-MJ
150412-MJ
150416-MJ
150604-MJ
150608-MJ
150612-MJ
150616-MJ
DNGM150404-MJ
150408-MJ
.016
a a
r a
.031
a a
r a
.047
s s
.063
s s
.016
s s
.031
s s
.047
s s
.063
s s
Applicable
Holder Page
Order Number
SH
Unstable Cutting
Stainless Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
NEG
WITH
HOLE
C010
012
E021
E024
H009
011
.016
.031
.016
a a
.031
a a
.047
a a
a a
.016
a a
s s
.031
a a
s s
.047
a a
a a
.016
.031
.016
.031
C010
E021
E024
H009
H011
C010
012
E021
E024
H009
011
C010
012
E021
E024
H009
011
C010
012
E021
E024
H009
011
.016
a s
a s
.031
a s
a s
Light
Cutting
C010
012
E021
E024
H009
011
CHIP BREAKER
A040
IDENTIFICATION
A002
A075
Mild Steel
Finish Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Medium Cutting
Light Cutting
Depth of Cut (inch)
Semi-Heavy Cutting
Heavy Cutting
Cast Iron (<350MPa)
Depth of Cut (inch)
TURNING INSERTS
MA

Depth of Cut (inch)
DN
55
DNMG 3 3 1
TYPE INSERTS
WITH HOLE
Flat Top
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Feed (inch/rev)
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
(inch)
MA
Medium
Cutting
MP
Medium
Cutting
MH
Medium
Cutting
A076
DNMG331MA
332MA
333MA
431MA
432MA
433MA
434MA
441MA
442MA
443MA
444MA
DNMG431MP
432MP
433MP
434MP
441MP
442MP
443MP
444MP
DNMG431MH
432MH
433MH
441MH
442MH
443MH
DNMG110404-MA
110408-MA
110412-MA
150404-MA
150408-MA
150412-MA
150416-MA
150604-MA
150608-MA
150612-MA
150616-MA
DNMG150404-MP
150408-MP
150412-MP
150416-MP
150604-MP
150608-MP
150612-MP
150616-MP
DNMG150404-MH
150408-MH
150412-MH
150604-MH
150608-MH
150612-MH
.016
a a
.031
a a
.047
a s
.016
a a a s
a a
a a
.031
a a a a
a a
a a
.047
a a a a
r a
a a
.063
.016 s
a s r
ss
.031 s
a ss
ss
ss
.047 s
a s r
ss
ss
.063
.016
a a a
.031
a a a
.047
a a a
.063
a a a
.016 s s s
.031 s s s
.047 s s s
.063
sss
.016
a a a a
.031
a a a a
.047
a a a s
.016 s s s
.031 s s s
.047 s s s

a
r
Carbide
Applicable
Holder Page
Coated
Shape
Unstable Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Stable Cutting
Feed (inch/rev)
C010
012
E021
E024
H009
011
s
s
C010
012
E021
E024
H009
011
C010
012
E021
E024
H009
011
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
(inch)
Standard
Medium
Cutting
MW
(With Wiper)
Medium
Cutting
MS
Medium
Cutting
R/L
Medium
Cutting
GH
Semi-Heavy
Cutting
GJ
Semi-Heavy
Cutting
*
*
*
*
DNMG332
431
432
433
434
441
442
443
444
DNMX432MW
433MW
442MW
443MW
DNMG110408
150404
150408
150412
150416
150604
150608
150612
150616
DNMX150408-MW
150412-MW
150608-MW
150612-MW
.031
DNMG332MS
431MS
432MS
433MS
441MS
442MS
443MS
DNGG431R
431L
432R
432L
441R
441L
442R
442L
DNMG432GH
433GH
442GH
443GH
DNMG432GJ
433GJ
434GJ
442GJ
443GJ
444GJ
Carbide
Applicable
Holder Page
Coated
Shape
Unstable Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
NEG
.016
a a a a
a a
sa
.031
a a s a
a a
sa
.047
a a s a
a a
sa
.063
WITH
HOLE
a
.016 s s s
ss
.031 s
a s
ss
ss
.047 s s s
ss
.063
.031
a a r
a a
.047
a a r
a a
ss
r
C010
012
E021
E024
H009
011
C010
E021
E024
H009
H011
.031 s
a r
ss
.047 s
a r
r r
DNMG110408-MS
150404-MS
150408-MS
150412-MS
150604-MS
150608-MS
150612-MS
DNGG150404R
150404L
150408R
150408L
150604R
150604L
150608R
150608L
DNMG150408-GH
150412-GH
150608-GH
150612-GH
.031
r s
.016
a a
a a a
a a a a
r a s
.031
a a
a a a
a a a a
r a s
.047
r a a
sss
.016
sss
a s
.031
sss
a s
.047
a s
DNMG150408-GJ
150412-GJ
150416-GJ
150608-GJ
150612-GJ
150616-GJ
.031
a a
.047
a a
a s
.063
ss
ss
.031
.047
.063
r ss
C010
012
E021
E024
H009
011
.016
sas
.016
sas
.031
sas
.031
sas
.016
.016
.031
C010
012
E021
E024
H009
011
.031
.031
a a s a
a a
a a
.047
a a s a
a a
a a
.031 s
a s
ss
ss
.047 s
a s
ss
ss
C010
012
E021
E024
H009
011
a s
C010
012
E021
E024
H009
011
Please refer to page A028 before using the MW breaker (wiper insert).
CHIP BREAKER
A040
IDENTIFICATION
A002
A077
Mild Steel
Finish Cutting
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Light Cutting
Depth of Cut (inch)
Heavy Cutting
Semi-Heavy Cutting
Cast Iron (<350MPa)

Flat Top
Depth of Cut (inch)
TURNING INSERTS
HZ

Depth of Cut (inch)
DN
55
DNMM 4 3 2
TYPE INSERTS
WITH HOLE
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Stable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Coated
Cermet Cermet
Heavy
Cutting
Flat Top
Flat Top
A078
DNMM432HZ
433HZ
434HZ
442HZ
443HZ
444HZ
DNMA431
432
433
434
442
443
DNGA431
432
DNMM150408-HZ
150412-HZ
150416-HZ
150608-HZ
150612-HZ
150616-HZ
DNMA150404
150408
150412
150416
150608
150612
DNGA150404
150408
.031
a a
r r
.047
a a
r r
.063
a a
r r
.031
a s
r r
.047
a s
r r
.063
a s
r r
C010
012
E021
E024
H009
011
.016
a a
.031
a a
.047
a a
.063
r r
.031
s s
.047
s s
s
s
s s
.016
r s s
.031
s s s

a
r
Carbide
Applicable
Holder Page
(inch)
HZ
Unstable Cutting
Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Feed (inch/rev)
Feed (inch/rev)
C010
012
E021
E024
H009
011
C010
012
E021
E024
H009
011
Standard
Depth of Cut (inch)
Standard
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Size Thickness
TURNING INSERTS
RN
RNMG 3 2
TYPE INSERTS
WITH HOLE
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
Feed (inch/rev)
Stainless Steel
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Medium
Cutting
Flat Top
RNMG32
43
54
64
86
106
RNMA43
RNMG090300
120400
150600
190600
250900
310900
RNMA120400
Coated
Cermet Cermet
Carbide
a a
a a
Applicable
Holder Page
(inch)
Standard
WITH
HOLE
Steel
Coated
Shape
Unstable Cutting
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Stable Cutting
C013
a a
C013
CHIP BREAKER
A040
IDENTIFICATION
A002
A079
SN

Mild Steel
Finish Cutting
Light Cutting
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)

Semi-Heavy Cutting
Heavy Cutting
Cast Iron (<350MPa)

Flat Top
Depth of Cut (inch)
TURNING INSERTS
90
SNMG 3 2 1 FH
TYPE INSERTS
WITH HOLE
Standard
NEG
Feed (inch/rev)
WITH
HOLE
Stable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Finish
Cutting
FS
SNMG321FH
322FH
431FH
432FH
SNMG090304-FH
090308-FH
120404-FH
120408-FH
.016
.031
SNMG431FS
432FS
SNMG432FY
.016
ss
sa
.031
a s
sa
SNMG120404-FS
120408-FS
.016
.031
SNMG120408-FY
.031
C014
017
E022
E025
C014
017
E022
E025
Finish
Cutting
FY
C014
017
E022
E025
Finish
Cutting
PK
SNGG432PK
SNGG120408-PK
.031
C014
017
E022
E025
Finish
Cutting
SA
SNMG431SA
432SA
433SA
SNMG120404-SA
120408-SA
120412-SA
.016
a r
.031
a a s
.047
a s
SNMG431SH
432SH
433SH
SNMG120404-SH
120408-SH
120412-SH
.016
ss
sa
.031
a a s
sa
.047
ss
sa
Light
Cutting
SH
Light
Cutting
A080

a
r
Carbide
Applicable
Holder Page
(inch)
FH
Unstable Cutting
Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Feed (inch/rev)
Feed (inch/rev)
Feed (inch/rev)
C014
017
E022
E025
C014
017
E022
E025
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
(inch)
SY
SNMG432SY
SNMG120408-SY
.031
Carbide
Light
Cutting
R/L 1G
Light
Cutting
MA
Medium
Cutting
MP
C014
017
E022
E025
SNMG321C
322C
432C
434C
SNMG090304-C
090308-C
120408-C
120416-C
.016
.031
.031
sa
.063
SNMG431R1G
431L1G
432R1G
432L1G
SNMG120404R-1G
120404L-1G
120408R-1G
120408L-1G
.016
.016
.031
.031
SNMG431MA
432MA
433MA
434MA
542MA
543MA
544MA
643MA
644MA
SNMG431MP
432MP
433MP
SNMG120404-MA
120408-MA
120412-MA
120416-MA
150608-MA
150612-MA
150616-MA
190612-MA
190616-MA
SNMG120404-MP
120408-MP
120412-MP
.016
a a ss
r a
.031
a a a a
a a
a a
.047
a a a a
a a
a a
.063
a a s a
r s
.047
a s a a
r a
r s
a
a
C014
017
E022
E025
a a
r s
a a
.063
.047
Medium
Cutting
SNMG431MH
432MH
433MH
643MH
644MH
SNMG120404-MH
120408-MH
120412-MH
190612-MH
190616-MH
C014
017
E022
E025
a a
.031
WITH
HOLE
C014
017
E022
E025
a as a
.063 s
a a a
.016
a a a
.031
a a a
.047
a a a
C014
017
E022
E025
Medium
Cutting
MH
NEG
Light
Cutting
Applicable
Holder Page
Coated
Shape
Unstable Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
.016
.031
a a a s
.047
a a a a
.047 s
a a
.063 s
a a
C014
017
E022
E025
CHIP BREAKER
A040
IDENTIFICATION
A002
A081
SN

Mild Steel
Finish Cutting
Light Cutting
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
Size Thickness Corner Radius

Heavy Cutting
Semi-Heavy Cutting
Cast Iron (<350MPa)

Flat Top
Depth of Cut (inch)
TURNING INSERTS
90
SNMG 3 2 1
TYPE INSERTS
WITH HOLE
Standard
NEG
Feed (inch/rev)
WITH
HOLE
Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Order Number
.016 s
a a
sa
.031 s
a a
sa
a ss
.016
a a s r
sa
.031
a a a a
ss
a s s a
a ss
.047
a a s a
ss
sa
a ss
.063
a a
a a
sa
(inch)
Standard
Medium
Cutting
MS
Medium
Cutting
R/L
Medium
Cutting
A082
SNMG321
322
323
431
432
433
434
435
533
543
643
644
856
866
SNMG321MS
322MS
431MS
432MS
433MS
434MS
542MS
543MS
644MS
SNGG321R
321L
322R
322L
431R
431L
432R
432L
433R
433L
SNMG090304
090308
090312
120404
120408
120412
120416
120420
150412
150612
190612
190616
250724
250924
SNMG090304-MS
090308-MS
120404-MS
120408-MS
120412-MS
120416-MS
150608-MS
150612-MS
190616-MS
SNGG090304R
090304L
090308R
090308L
120404R
120404L
120408R
120408L
120412R
120412L
.047
s
a
C014
017
E022
E025
.079
.047
.047
a a a a
a a
.047
a a a a
ss
ss
.063 s
a a a
.094
.094
.016
a
r s
r s
.031
.016
s a
.031
a a
a a a
sss a
r r a r
.047
a a a
sss
r s r
.063
r s
.031
r r
.047
r r
.063
r s
sss
.016
sss
.031
sss
.031
ss
.016
sss
.016
sss
.031
sss
.031
sss
.047
.047
C014
017
E022
E025
.016

a
r
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Coated
Shape
Unstable Cutting
Applicable
Holder Page
Work
Material
P
M
K
N
S
Feed (inch/rev)
Feed (inch/rev)
Feed (inch/rev)
s
a
C014
017
E022
E025
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Semi-Heavy
Cutting
HZ
Heavy
Cutting
HX
Heavy
Cutting
HV
Heavy
Cutting
HAS
Coated
Cermet Cermet
SNMG432GH
433GH
434GH
543GH
544GH
643GH
644GH
866GH
SNMM432HZ
433HZ
543HZ
643HZ
644HZ
646HZ
SNMM543HX
544HX
643HX
644HX
646HX
856HX
858HX
866HX
868HX
SNMM644HV
646HV
856HV
866HV
SNMG120408-GH
120412-GH
120416-GH
150612-GH
150616-GH
190612-GH
190616-GH
250924-GH
SNMM120408-HZ
120412-HZ
150612-HZ
190612-HZ
190616-HZ
190624-HZ
SNMM150612-HX
150616-HX
190612-HX
190616-HX
190624-HX
250724-HX
250732-HX
250924-HX
250932-HX
SNMM190616-HV
190624-HV
250724-HV
250924-HV
SNMG866HAS
SNMG250924-HAS .094
.031
a a s
ss
a a
.047
a a s
ss
a a
.063
a a
ss
.047 s
.063
.047 s
.063
Carbide
a a
a a
.094
.031
a s
r r
.047
a a
r r
.047
a s
r r
.047
a s
s r r
.063
a a
s r r
.094
a r
.047
a r r a
.063
a a
.047
a s r s
.063
a s r s
.094
a s r s
.094
a s r s
.126
r r s
.094
a s r s
C014
017
E022
E025
C014
017
E022
E025
.126
r r s
.063
a a r s
.094
a a r s
.094
a a r s
.094
a a r s
NEG
WITH
HOLE
ss
a a
Applicable
Holder Page
(inch)
GH
Unstable Cutting
Stainless Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
C014
017
E025
C014
017
E025
C014
Heavy
Cutting
HXD
Heavy
Cutting
SNMM643HXD
644HXD
646HXD
866HXD
SNMM190612-HXD
190616-HXD
190624-HXD
250924-HXD
.047
.063
.094
.094
C014
017
CHIP BREAKER
A040
IDENTIFICATION
A002
A083
SN

Mild Steel
Finish Cutting
Light Cutting
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)

Heavy Cutting
Semi-Heavy Cutting
Cast Iron (<350MPa)
Depth of Cut (inch)
TURNING INSERTS
90
SNMA 3 2 1
TYPE INSERTS
WITH HOLE
Flat Top
Standard
NEG
Feed (inch/rev)
WITH
HOLE
Stable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Coated
Cermet Cermet
Flat Top
A084
SNMA321
322
323
431
432
433
434
543
643
644
SNGA320.5
321
322
431
432
433
SNMA090304
090308
090312
120404
120408
120412
120416
150612
190612
190616
SNGA090302
090304
090308
120404
120408
120412
.016
.031
s
a a
.047
.016
.031
a a
a ss
.047
a a
a ss
.063
a a
.047
a a
.047
a a
.063
a a
.008
.016
s
s
C014
017
E022
E025
sss
sss
.031
.016
sss
.031
sss
.047

a
r
Carbide
Applicable
Holder Page
(inch)
Flat Top
Unstable Cutting
Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Feed (inch/rev)
Feed (inch/rev)
Feed (inch/rev)
C014
017
E022
E025
TN

Mild Steel
Finish Cutting
Light Cutting
Medium Cutting
FH

Semi-Heavy Cutting
Heavy Cutting
Cast Iron (<350MPa)
.315
.236
.197
.157
.118
SW
.079
MW
Flat Top
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
.276
TURNING INSERTS
60
TNMG 2 2 1
TYPE INSERTS
WITH HOLE
Standard
.039
0
Feed (inch/rev)
.004
Feed (inch/rev)
.012
.020
Stable Cutting
General Cutting
Finish
Cutting
FS
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
TNMG221FH
330.5FH
331FH
332FH
TNMG110304-FH
160402-FH
160404-FH
160408-FH
TNMG331FS
332FS
.016
Carbide
C018
023
E022
E025
.008
a a
a a
.016
a s
sa
.031
a s
sa
TNMG160404-FS
160408-FS
.016
.031
TNMG331FY
332FY
TNMG160404-FY
160408-FY
.016
.031
TNGG331PK
332PK
TNGG160404-PK
160408-PK
.016
.031
TNGG330.5RFS
330.5LFS
331RFS
331LFS
332RFS
332LFS
TNGG330.5RF
330.5LF
331RF
331LF
332RF
332LF
TNGG160402R-FS
160402L-FS
160404R-FS
160404L-FS
160408R-FS
160408L-FS
TNGG160402R-F
160402L-F
160404R-F
160404L-F
160408R-F
160408L-F
.008
.008
.016
.016
.031
C018
023
E022
E025
Finish
Cutting
PK
Finish
Cutting
R/L F
Finish
Cutting
C018
023
E022
E025
C018
023
E022
E025
Finish
Cutting
R/L FS
Applicable
Holder Page
Finish
Cutting
FY
WITH
HOLE
Stainless Steel
(inch)
FH
Unstable Cutting
Steel
Coated
Shape
Feed (inch/rev)
Feed (inch/rev)
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
NEG
.028
Feed (inch/rev)
C018
023
E022
E025
.031
.008
ss
.008
ss
.016
ss
.016
ss
.031
ss
.031
ss
C018
023
E022
E025
CHIP BREAKER
A040
IDENTIFICATION
A002
A085

Mild Steel
Finish Cutting
Medium Cutting
Light Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)

Semi-Heavy Cutting
Heavy Cutting
Cast Iron (<350MPa)
Depth of Cut (inch)
TN
Depth of Cut (inch)
TURNING INSERTS
60
TNMG 3 3 1 SA
TYPE INSERTS
WITH HOLE
Flat Top
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Feed (inch/rev)
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Coated
Shape
(inch)
SA
Light
Cutting
SH
Light
Cutting
SW
(With Wiper)
*
*
Unstable Cutting
TNMG331SA
332SA
333SA
432SA
433SA
TNMG331SH
332SH
333SH
432SH
TNMG160404-SA
160408-SA
160412-SA
220408-SA
220412-SA
TNMG160404-SH
160408-SH
160412-SH
220408-SH
.016
a a a
a a
.031
a a a
a a
.047
a a a
.031
a a a
a a
.047
a s
a a
.016
a a s
sa
.031
a a s
sa
sa
.031
a a s
TNMX331SW
332SW
TNMX160404-SW
160408-SW
.016
a a
sa
.031
a a
sa
C018
023
E022
E025
.047
Carbide
Applicable
Holder Page
Work
Material
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
P
M
K
N
S
Stable Cutting
Feed (inch/rev)
a
a
C018
023
E022
E025
C018
C022
Light
Cutting
SY
TNMG331SY
332SY
TNMG160404-SY
160408-SY
.016
.031
TNMG222C
331C
332C
333C
431C
432C
TNMG331R1M
331L1M
332R1M
332L1M
TNMG110308-C
160404-C
160408-C
160412-C
220404-C
220408-C
TNMG160404R-1M
160404L-1M
160408R-1M
160408L-1M
.031
.016
sa
.031
sa
.047
.016
sa
.031
sa
.016
.016
.031
.031
Light
Cutting
Light
Cutting
R/L 1M
Light
Cutting
A086

a
r
C018
023
E022
E025
C018
023
E022
E025
C018
023
E022
E025
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
(inch)
R/L 1G
Light
Cutting
R/L K
Light
Cutting
MJ
TNMG331R1G
331L1G
332R1G
332L1G
431R1G
431L1G
432L1G
432R1G
TNGG330.5RK
330.5LK
331RK
331LK
332RK
332LK
TNMG331MJ
332MJ
333MJ
TNMG160404R-1G
160404L-1G
160408R-1G
160408L-1G
220404R-1G
220404L-1G
220408L-1G
220408R-1G
TNGG160402R-K
160402L-K
160404R-K
160404L-K
160408R-K
160408L-K
TNMG160404-MJ
160408-MJ
160412-MJ
.016
.016
.031
.031
.016
.016
.031
.031
.008
ss
.008
ss
.016
ss
.016
ss
.031
ss
TNMG321MA
322MA
331MA
332MA
333MA
334MA
432MA
433MA
434MA
542MA
543MA
TNMG331MP
332MP
333MP
432MP
433MP
TNMG331MH
332MH
333MH
432MH
433MH
TNMG160304-MA
160308-MA
160404-MA
160408-MA
160412-MA
160416-MA
220408-MA
220412-MA
220416-MA
270608-MA
270612-MA
TNMG160404-MP
160408-MP
160412-MP
220408-MP
220412-MP
TNMG160404-MH
160408-MH
160412-MH
220408-MH
220412-MH
.016
.031
a a
.016
a a a s
a a
a a
.031
a a a a
a a
a a
.047
a a a a
a a
a a
.031
Carbide
Medium
Cutting
MP
Medium
Cutting
MH
Medium
Cutting
NEG
WITH
HOLE
C018
023
E022
E025
C018
023
E022
E025
ss
.016
a a
r a
.031
a a
a a
.047
ss
Light
Cutting
MA
Applicable
Holder Page
TURNING INSERTS
Stainless Steel
Coated
Shape
Unstable Cutting
Steel
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
General Cutting
Stable Cutting
P
M
K
N
S
C018
023
E022
E025
.063
C018
023
E022
E025
a a
.031
a a a a
a a
.047
a a a a
a a
a a
a a
a a
.063
.031
a a a a
.047
a a a a
r a
.016
a a a
.031
a a a
.047
a a a
.031
a a a
.047
a a a
.016
a a a s
.031
a a a s
.047
a a a s
.031
a a a a
.047
a a a a
C018
023
E022
E025
C018
023
E022
E025
CHIP BREAKER
A040
IDENTIFICATION
A002
A087

Mild Steel
Finish Cutting
Medium Cutting
Light Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)

Heavy Cutting
Semi-Heavy Cutting
Cast Iron (<350MPa)

Flat Top
Depth of Cut (inch)
TN
Depth of Cut (inch)
TURNING INSERTS
60
TNMG 2 2 1
TYPE INSERTS
WITH HOLE
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Order Number
.016
a s
.031
a a
.016
a r
(inch)
Standard
Medium
Cutting
MW
(With Wiper)
TNMG221
222
321
322
331
332
333
334
335
431
432
433
434
436
542
543
544
666
TNMX332MW
333MW
TNMG110304
110308
160304
160308
160404
160408
160412
160416
160420
220404
220408
220412
220416
220424
270608
270612
270616
330924
TNMX160408-MW
160412-MW
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Coated
Shape
Unstable Cutting
.031
a a a
.016
a a a a
.031
.047
.063
s s
a a a a
s s
s a s s
s s
a r
s s
s a
.079
s a
a s a
s a
a s a
s a
s s s
s s
.016
a a a a
.031
a a a a
a a
.047
a a a a
s s
.063
a a
s s
s a
.094
Applicable
Holder Page
Work
Material
P
M
K
N
S
Feed (inch/rev)
Feed (inch/rev)
C018
023
E022
E025
.031
.047
a a a
.063
a s a
.094
a a
.031
a a r
r s
.047
a a r
s s
C018
C022
Medium
Cutting
MS
Medium
Cutting
TNMG331MS
332MS
333MS
432MS
433MS
TNMG160404-MS
160408-MS
160412-MS
220408-MS
220412-MS
.016
a a
a a a
a a s s
r s r
.031
a a
a a a
a a s a
s r a r
.047
s s s
s a
.031
a r
a a a
a a s a
.047
A088

a
r
r s
r a r
C018
023
E022
E025
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Coated
Cermet Cermet
Medium
Cutting
R/L 2M
Medium
Cutting
R/L 2G
Medium
Cutting
R/L
Medium
Cutting
TNMG331RES
331LES
332RES
332LES
432RES
432LES
TNMG331R2M
331L2M
332R2M
332L2M
TNMG160404R-ES
160404L-ES
160408R-ES
160408L-ES
220408R-ES
220408L-ES
TNMG160404R-2M
160404L-2M
160408R-2M
160408L-2M
.016
ss
.016
ss
.031
ss
.031
ss
.031
.031
TNMG331R2G
331L2G
332R2G
332L2G
TNMG160404R-2G
160404L-2G
160408R-2G
160408L-2G
.016
.016
.031
.031
TNGG220.5R
220.5L
221R
221L
222R
222L
321R
321L
322R
322L
330.5R
330.5L
331R
331L
332R
332L
333R
333L
431R
431L
432R
432L
433R
433L
TNGG110302R
110302L
110304R
110304L
110308R
110308L
160304R
160304L
160308R
160308L
160402R
160402L
160404R
160404L
160408R
160408L
160412R
160412L
220404R
220404L
220408R
220408L
220412R
220412L
.008
ss
.008
ss
.016
Carbide
NEG
C018
023
E022
E025
.016
.016
.031
.031
WITH
HOLE
C018
023
E022
E025
C018
023
E022
E025
s
ss
.016
ss
.031
ss
.031
ss
.016
ss
.016
ss
.031
ss
.031
ss
.008
sss
.008
sss
.016
sas
sss
.016
sas
sss
.031
sas
sss
.031
sas
sss
.047
sss
srs
.047
ss
.016
sas
.016
sas
.031
sas
sss
.031
sas
sss
.047
.047
Applicable
Holder Page
(inch)
R/L ES
Unstable Cutting
Stainless Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
r
s
C018
023
E022
E025
s
s
CHIP BREAKER
A040
IDENTIFICATION
A002
A089

Mild Steel
Finish Cutting
Light Cutting
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)

Semi-Heavy Cutting
Heavy Cutting
Cast Iron (<350MPa)
Depth of Cut (inch)
TN
Depth of Cut (inch)
TURNING INSERTS
60
TNMG 3 3 2 GH
TYPE INSERTS
WITH HOLE
Flat Top
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Stable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Semi-Heavy
Cutting
HZ
Heavy
Cutting
HV
Coated
Cermet Cermet
TNMG332GH
333GH
432GH
433GH
434GH
543GH
544GH
666GH
TNMM332HZ
432HZ
433HZ
434HZ
TNMG160408-GH
160412-GH
220408-GH
220412-GH
220416-GH
270612-GH
270616-GH
330924-GH
TNMM160408-HZ
220408-HZ
220412-HZ
220416-HZ
.031
TNMM666HV
TNMM330924-HV
.094
a a s a
a a
a a
.047 s s s
ss
a a
.031
a a a a
a a
a a
.047
a a s a
a a
a a
.063
a a s
ss
.047
a a a a
.063
a a
.094
a a
.031
s a
r r
.031
a a
r r
.047
a a
r r
.063
a s
r r
Carbide
Applicable
Holder Page
(inch)
GH
Unstable Cutting
Steel
Coated
Shape
General Cutting
Feed (inch/rev)
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Feed (inch/rev)
C018
023
E022
E025
C018
023
E022
E025
a r
C018
020
C023
Heavy
Cutting
A090
: Inventory maintained. : Inventory maintained in Japan.

Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Coated
Cermet Cermet
Flat Top
TNMA221
222
321
322
331
332
333
334
335
431
432
433
434
436
438
543
TNGA221
222
321
322
330.5
331
332
333
334
431
432
433
TNMA110304
110308
160304
160308
160404
160408
160412
160416
160420
220404
220408
220412
220416
220424
220432
270612
TNGA110304
110308
160304
160308
160402
160404
160408
160412
160416
220404
220408
220412
Carbide
.016
r
WITH
HOLE
.016
.031
.016
a a
sss
.031
a a
ss a
.047
a a
r ss
.063
ss
.079
ss
s
r
.016
r ss
.031
a a
.047
a a
.063
a a
.126
.047
.016
.031
C018
023
E022
E025
ss a
.094
r s
.016
r s
.031
.008
.016
sss
.031
sss
.047
ss
.063
.016
sr s
.047
NEG
s a
.031
.031
Applicable
Holder Page
(inch)
Flat Top
Unstable Cutting
Stainless Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
C018
023
E022
E025
sss
s
CHIP BREAKER
A040
IDENTIFICATION
A002
A091
VN

Mild Steel
Finish Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Medium Cutting
Depth of Cut (inch)
Light Cutting
FH

Semi-Heavy Cutting
Cast Iron (<350MPa)

Flat Top
Depth of Cut (inch)
TURNING INSERTS
35
VNMG 3 3 0.5
TYPE INSERTS
WITH HOLE
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
(inch)
FH
Carbide
VNMG330.5FH
331FH
332FH
VNMG160402-FH
160404-FH
160408-FH
.008
a a
a a
.016
ss
sa
.031
ss
sa
VNMG331FS
332FS
VNMG160404-FS
160408-FS
.016
.031
VNGG33V5FJ
330.2FJ
330.5FJ
VNGG1604V5-FJ
160401-FJ
160402-FJ
.002
.004
.008
VNGG330.5RF
330.5LF
331RF
331LF
VNGG160402R-F
160402L-F
160404R-F
160404L-F
.008
a a
.008
a a
.016
a a
.016
a a
VNMG331SH
332SH
VNMG160404-SH
160408-SH
.016
a s a
sa
.031
a s a
sa
VNMG331MJ
332MJ
333MJ
VNMG160404-MJ
160408-MJ
160412-MJ
.016
a a
r a
.031
a a
r a
.047
ss
C024
026
E023
E026
Finish
Cutting
FS
C024
026
E023
E026
Finish
Cutting
FJ
Finish
Cutting
R/L F
Finish
Cutting
SH
Light
Cutting
A092
C024
026
E023
E026
C024
026
E023
E026
C024
026
E023
E026
Light
Cutting
MJ
Applicable
Holder Page
Coated
Shape
Unstable Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Feed (inch/rev)
C024
026
E023
E026
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
(inch)
MJ
Light
Cutting
MA
Carbide
VNGM331MJ
332MJ
431MJ
432MJ
VNGM160404-MJ
160408-MJ
220404-MJ
220408-MJ
.016
.031
.016
.031
VNMG331MA
332MA
VNMG160404-MA
160408-MA
.016
a a a a
a a
a a
.031
a a a a
a a
a a
VNMG331MP
332MP
333MP
VNMG160404-MP
160408-MP
160412-MP
.016
a a a
.031
a a a
.047
a a a
VNMG331MH
332MH
VNMG160404-MH
160408-MH
.016
a a a s
.031
a a a s
VNMG331
332
333
VNMG160404
160408
160412
.016
a a s
ss
.031
a a a
sa
.047 s
VNMG331MS
332MS
VNMG160404-MS
160408-MS
.016
a a a
a a
r a
.031
a a a
s a
r a
VNGG331R
331L
332R
VNGG160404R
160404L
160408R
.016
sa
.016
sa
VNGA331
332
VNGA160404
160408
.016
r s a
.031
ss a
ss
sa
sa
sa
Medium
Cutting
MS
Medium
Cutting
R/L
.031
Medium
Cutting
Flat Top
WITH
HOLE
C024
026
E023
E026
Medium
Cutting
Standard
C024
026
E023
E026
C024
026
E023
E026
Medium
Cutting
MH
NEG
C024
026
E023
E026
Medium
Cutting
MP
Applicable
Holder Page
Coated
Shape
Unstable Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
C024
026
E023
E026
C024
026
E023
E026
C024
026
E023
E026
C024
026
E023
E026
CHIP BREAKER
A040
IDENTIFICATION
A002
A093
WN

Mild Steel
Finish Cutting
Light Cutting
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
FH

Semi-Heavy Cutting
Heavy Cutting
Cast Iron (<350MPa)
Depth of Cut (inch)
TURNING INSERTS
80
WNMG 4 3 1
TYPE INSERTS
WITH HOLE
Flat Top
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Stable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
WNMG431FH
432FH
WNMG080404-FH
080408-FH
.016
WNMG431FS
432FS
WNMG080404-FS
080408-FS
.016
WNMG431FY
432FY
WNMG080404-FY
080408-FY
.016
WNMG431SA
432SA
433SA
WNMG080404-SA
080408-SA
080412-SA
.016
WNMG321SH
322SH
32.51SH
32.52SH
32.53SH
331SH
332SH
333SH
431SH
432SH
433SH
WNMG060304-SH
060308-SH
06T304-SH
06T308-SH
06T312-SH
060404-SH
060408-SH
060412-SH
080404-SH
080408-SH
080412-SH
.016
.031
Finish
Cutting
FS
.031
Finish
Cutting
FY
.031
Finish
Cutting
SA
.031
.047
Light
Cutting
SH
Light
Cutting
A094
Carbide
C027
E023
E026
E027
C027
E023
E026
E027
C027
E023
E026
E027
C027
E023
E026
E027
.031
.016
.031
.047
.016
.031
.047
.016
.031
.047

a
r
Coated
Cermet Cermet
Applicable
Holder Page
(inch)
FH
Unstable Cutting
Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Feed (inch/rev)
C027
E023
E026
E027
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Light
Cutting
SY
Coated
Cermet Cermet
WNMG331SW
332SW
431SW
432SW
433SW
WNMG431SY
432SY
WNMG060404-SW
060408-SW
080404-SW
080408-SW
080412-SW
WNMG080404-SY
080408-SY
.016
WNMG431C
432C
WNMG080404-C
080408-C
.016
WNMG432MJ
433MJ
434MJ
WNMG080408-MJ
080412-MJ
080416-MJ
.031
WNMG32.51MA
32.52MA
32.53MA
331MA
332MA
333MA
431MA
432MA
433MA
434MA
543MA
544MA
WNMG32.51MP
32.52MP
32.53MP
331MP
332MP
333MP
431MP
432MP
433MP
434MP
WNMG06T304-MA
06T308-MA
06T312-MA
060404-MA
060408-MA
060412-MA
080404-MA
080408-MA
080412-MA
080416-MA
100612-MA
100616-MA
WNMG06T304-MP
06T308-MP
06T312-MP
060404-MP
060408-MP
060412-MP
080404-MP
080408-MP
080412-MP
080416-MP
.016
Carbide
.031
.031
.016
.031
C027
E023
E026
E027
.031
C027
E023
E026
E027
.047
C027
E023
E026
E027
.063
Light
Cutting
MA
Medium
Cutting
MP
Medium
Cutting
WITH
HOLE
.047
Light
Cutting
MJ
NEG
C027
E023
E026
E027
.016
Light
Cutting
Applicable
Holder Page
(inch)
SW
(With Wiper)
Unstable Cutting
Stainless Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
.031
.047
.016
.031
C027
E023
E026
E027
.047
.016
.031
.047
.063
.047
.063
.016
.031
.047
.016
C027
E023
E026
E027
.031
.047
.016
.031
.047
.063
Please refer to page A028 before using the SW breaker (wiper insert).
CHIP BREAKER
A040
IDENTIFICATION
A002
A095
WN

Mild Steel
Finish Cutting
Light Cutting
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
MH

Semi-Heavy Cutting
Heavy Cutting
Cast Iron (<350MPa)
Depth of Cut (inch)
TURNING INSERTS
80
WNMG 4 3 1
TYPE INSERTS
WITH HOLE
Flat Top
Standard
NEG
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Stable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Coated
Cermet Cermet
WNMG431MH
432MH
433MH
WNMG080404-MH
080408-MH
080412-MH
.016
WNMG431
432
433
434
WNMG080404
080408
080412
080416
.016
WNMG332MW
333MW
432MW
433MW
WNMG060408-MW
060412-MW
080408-MW
080412-MW
.031
WNMG321MS
322MS
32.51MS
32.52MS
331MS
332MS
431MS
432MS
433MS
WNMG432GH
433GH
WNMG060304-MS
060308-MS
06T304-MS
06T308-MS
060404-MS
060408-MS
080404-MS
080408-MS
080412-MS
WNMG080408-GH
080412-GH
.016
Carbide
.031
C027
E023
E026
E027
.047
Medium
Cutting
Standard
Medium
Cutting
MW
(With Wiper)
Medium
Cutting
MS
Medium
Cutting
GH
Applicable
Holder Page
(inch)
MH
Unstable Cutting
Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Feed (inch/rev)
.031
C027
E023
E026
E027
.047
.063
.047
C027
E023
E026
E027
.031
.047
.031
.016
.031
C027
E023
E026
E027
.016
.031
.016
.031
.047
.031
.047
C027
E023
E026
E027
Semi-Heavy
Cutting
A096

a
r
CHIP BREAKER
A040
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Semi-Heavy
Cutting
Flat Top
Coated
Cermet Cermet
WNMG432GJ
433GJ
434GJ
543GJ
WNMG080408-GJ
080412-GJ
080416-GJ
100612-GJ
.031
WNMA431
432
433
434
WNMA080404
080408
080412
080416
.016
Carbide
.047
Applicable
Holder Page
(inch)
GJ
Unstable Cutting
Stainless Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
Stable Cutting
Steel
NEG
C027
E023
E026
E027
.063
.047
.031
TURNING INSERTS
P
M
K
N
S
WITH
HOLE
C027
E023
E026
E027
.047
.063
CHIP BREAKER
A040
IDENTIFICATION
A002
A097
55
KN
TYPE INSERTS
WITHOUT HOLE
Work
Material
P
M
K
N
S
Stable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
(ISO) Number
Dimensions (inch)
D1
L1
S1
Re
.016 s
.375
.625
.217
.016
.031
.375
.625
.217
.031
.047 s
.375
.625
.217
.047
.375
.636
.187
.020
(inch)
WITHOUT
HOLE
UTi20T
Order Number
Corner
Radius
UE6110
UE6020
Shape
Unstable Cutting
M1/M2 Breaker
Steel
Coated Carbide
NEG
General Cutting
KNMX5X1R
5X2R
5X3R
KNMX190504R
190508R
190512R
KNUX160405RM1
KNUX160405R-M1 .020
Applicable
Holder Page
TURNING INSERTS
Semi-Heavy
Cutting
M1

Semi-Heavy
Cutting
M2
KNUX160405RM2
KNUX160405R-M2 .020
.375
.636
.187
.020
Semi-Heavy
Cutting
A098

SN
Size
Thickness Corner Radius

Semi-Heavy Cutting
Depth of Cut (inch)
Cast Iron (<350MPa)
TURNING INSERTS
90
SNMN 3 2 1
TYPE INSERTS
WITHOUT HOLE
Flat Top
NEG
Feed (inch/rev)
Flat Top
WITHOUT
HOLE
Stainless Steel
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Coated
Cermet Cermet
SNMN321
322
422
432
433
434
435
533
633
SNG321
322
422
431
432
433
SNMN090304
090308
120308
120408
120412
120416
120420
150412
190412
SNGN090304
090308
120308
120404
120408
120412
Carbide
.016
Applicable
Holder Page
(inch)
Flat Top
Unstable Cutting
Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Stable Cutting
.031
.031
.031
ss
sss
.047
a a
sr s
.063
a a
.079
C014
017
E025
.047
.047
.016
.031
.031
.016
sss
.031
sss
.047
C014
017
E025
r ss
CHIP BREAKER
A066
IDENTIFICATION
A002
A099

TURNING INSERTS
60
TN
TNMN 3 2 2
TYPE INSERTS
WITHOUT HOLE

Semi-Heavy Cutting
Depth of Cut (inch)
Cast Iron (<350MPa)
Flat Top
NEG
Feed (inch/rev)
WITHOUT
HOLE
Stainless Steel
Cast Iron
Non-Ferrous Metal
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UE6035
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
Order Number
Coated
Cermet Cermet
Flat Top
A100
TNMN322
332
333
334
335
431
432
433
434
TNG221
222
321
322
331
332
333
TNMN160308
160408
160412
160416
160420
220404
220408
220412
220416
TNGN110304
110308
160304
160308
160404
160408
160412
.031
.031
ss
.047
ss
.063
ss
.079
ss
r
r s
s
s
.063
.016
.031
.016
.031
.016
.031
.047
C019
021
C023
E025
.047

s
s
.016
.031
Carbide
Applicable
Holder Page
(inch)
Flat Top
Unstable Cutting
Steel
Coated
Shape
General Cutting
UTi20T
HTi05T
HTi10
RT9005
RT9010
TF15
Work
Material
P
M
K
N
S
Stable Cutting
C019
021
C023
E025
CHIP BREAKER
A066
TURNING INSERTS [POSITIVE]
CC
Standard
Depth of Cut (inch)
Standard
POSI
7
Feed (inch/rev)
Stable Cutting
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Order Number
Carbide
(inch)
FV
Finish
Cutting
FJ
Finish
Cutting
FJ-P
Finish
Cutting
AZ
Finish
Cutting
WITH
HOLE
Steel
Coated
Shape
Unstable Cutting
CCMT21.50.5FV
21.51FV
32.50.5FV
32.51FV
32.52FV
CCGT21.5V5FJ
21.50.2FJ
21.50.5FJ
32.5V5FJ
32.50.2FJ
32.50.5FJ
32.51FJ
CCGT21.5V5FJ-P
21.50.2FJ-P
21.50.5FJ-P
32.5V5FJ-P
32.50.2FJ-P
32.50.5FJ-P
32.51FJ-P
CCGT21.50.5AZ
21.51AZ
32.50.5AZ
32.51AZ
32.52AZ
430.5AZ
431AZ
432AZ
CCMT060202-FV
060204-FV
09T302-FV
09T304-FV
09T308-FV
CCGT0602V5-FJ
060201-FJ
060202-FJ
09T3V5-FJ
09T301-FJ
09T302-FJ
09T304-FJ
CCGT0602V5-FJ-P
060201-FJ-P
060202-FJ-P
09T3V5-FJ-P
09T301-FJ-P
09T302-FJ-P
09T304-FJ-P
CCGT060202-AZ
060204-AZ
09T302-AZ
09T304-AZ
09T308-AZ
120402-AZ
120404-AZ
120408-AZ
.008
s a
.016
s a
.008
a a
.016
s a
.031
s a
.002
Applicable
Holder Page
Work
Material
Medium Cutting
Standard
P
M
K
N
S
Light Cutting
Feed (inch/rev)
Feed (inch/rev)

Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Finish Cutting
Size
TURNING INSERTS
80
CCMT 2 1.5 0.5 FV
TYPE INSERTS
WITH HOLE
C030
D008
D012
E006
E012
E013
.004
.008
.002
.004
.008
.016
C030
D008
D012
E006
E012
E013
.002
.004
.008
.002
.004
.008
.016
.008
.016
.008
.016
.031
.008
.016
.031
C030
D008
D012
E006
E012
E013
C030
D008
D012
E006
E012
E013
CHIP BREAKER
A054
IDENTIFICATION
A002
A101
CC
Standard
Light Cutting
WITH
HOLE
Feed (inch/rev)
Work
Material
P
M
K
N
S
Medium Cutting
Standard
Feed (inch/rev)
Feed (inch/rev)
Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
(inch)
L-F
Finish
Cutting
R/L F
Finish
Cutting
SV
CCGT03S1V3L-F
03S101L-F
03S102L-F
03S104L-F
04T0V3L-F
04T001L-F
04T002L-F
04T004L-F
CCGH21.50.5RF
21.50.5LF
21.51RF
21.51LF
CCGT03S1V3L-F
03S101L-F
03S102L-F
03S104L-F
04T0V3L-F
04T001L-F
04T002L-F
04T004L-F
CCGH060202R-F
060202L-F
060204R-F
060204L-F
.0012
.004
.008
CCMH21.50.5SV
21.51SV
CCMH060202-SV
060204-SV
.008
.016
CCMT21.50.5SW
21.51SW
32.50.5SW
32.51SW
CCMT060202-SW
060204-SW
09T302-SW
09T304-SW
.008
a a
.016
a a
.008
a a
.016
a a
.016
.0012
.004
.008
.016
.008
.008
.016
.016
s a
s a
s a
s a
E012
E029
Light
Cutting
SW
(With Wiper)
Light
Cutting
Please refer to page A028 before using the SW breaker (wiper insert).
A102

a
r
Applicable
Holder Page
POSI
7
Standard

Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Finish Cutting
Depth of Cut (inch)
TURNING INSERTS
80
CCGT 03 S1 V3 L-F
TYPE INSERTS
WITH HOLE
C030
D008
D012
E006
E012
E013
C030
D008
D012
E006
E012
E013
C030
D008
D012
E006
E012
E013
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
(inch)
R/L SS
Light
Cutting
MJ
CCGT21.5V3RSS
21.5V3LSS
21.50.2RSS
21.50.2LSS
21.50.5RSS
21.50.5LSS
32.5V3RSS
32.5V3LSS
32.50.2RSS
32.50.2LSS
32.50.5RSS
32.50.5LSS
CCGT21.51MJ
32.52MJ
CCGT0602V3R-SS
0602V3L-SS
060201R-SS
060201L-SS
060202R-SS
060202L-SS
09T3V3R-SS
09T3V3L-SS
09T301R-SS
09T301L-SS
09T302R-SS
09T302L-SS
CCGT060204-MJ
09T308-MJ
CCGT21.51MJ-P
32.52MJ-P
CCGT060204-MJ-P .016
09T308-MJ-P .031
.0012
.0012
.004
.004
.008
.008
.0012
.0012
.004
.004
.008
.008
C030
D008
D012
E006
E012
E013
.016
.031
C030
D008
D012
E006
E012
E013
a
a
Medium
Cutting
Standard CCMT21.50.5
Medium
Cutting
MV
21.51
21.52
2.520.5
2.521
2.522
32.50.5
32.51
32.52
431
432
433
CCMH21.50.5MV
21.51MV
CCMT060202
060204
060208
080302
080304
080308
09T302
09T304
09T308
120404
120408
120412
CCMH060202-MV
060204-MV
POSI
7
WITH
HOLE
Medium
Cutting
MJ-P
Applicable
Holder Page
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
.008
a a
s a
.016
a a a
a s s a
.031
a a
.008
.016
s r
s a
.031
s r
.008
a a
s a
.016
a a a
s a
.031
a a a
a s s a
.016
a a a
s a
.031
a a a
s a
.047
a a
r a
.008
a a
s a
.016
a a
s a
C030
D008
D012
E006
E012
E013
C030
D008
D012
E006
E012
E013
Medium
Cutting
C030
D008
D012
E006
E012
E013
CHIP BREAKER
A054
IDENTIFICATION
A002
A103
CC
Standard
WITH
HOLE
Work
Material
Medium Cutting
Standard
Feed (inch/rev)
P
M
K
N
S
Light Cutting
Feed (inch/rev)
Feed (inch/rev)
Stable Cutting
General Cutting
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape

(inch)
MW
(With Wiper)
Medium
Cutting
R/L SR
Medium
Cutting
A104
* CCMT21.51MW
21.52MW
*
32.51MW
*
32.52MW
*
431MW
*
432MW
* CCET21.5V3RSR
21.5V3LSR
21.50.2RSR
21.50.2LSR
21.50.5RSR
21.50.5LSR
21.51RSR
21.51LSR
32.5V3RSR
32.5V3LSR
32.50.2RSR
32.50.2LSR
32.50.5RSR
32.50.5LSR
32.51RSR
32.51LSR
CCMT060204-MW
060208-MW
09T304-MW
09T308-MW
120404-MW
120408-MW
CCET0602V3R-SR
0602V3L-SR
060201R-SR
060201L-SR
060202R-SR
060202L-SR
060204R-SR
060204L-SR
09T3V3R-SR
09T3V3L-SR
09T301R-SR
09T301L-SR
09T302R-SR
09T302L-SR
09T304R-SR
09T304L-SR
.016
.031
a a
.016
a a
.031
a a
.016
a a
.031
a a
.0012
.004
.004
.008
.008
.016
.016
.0012
.0012
.004
.004
.008
.008
.016
.016

C030
D008
D012
E006
E012
E013
.0012
Please refer to page A028 before using the MW breaker (wiper insert).
Applicable
Holder Page
POSI
7
Standard
Size
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Finish Cutting
Depth of Cut (inch)
TURNING INSERTS
80
CCMT 2 1.5 1 MW
TYPE INSERTS
WITH HOLE
C030
D008
D012
E006
E012
E013
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
(inch)
R/L SN
Medium
Cutting
R/L SN
Medium
Cutting
R/L WSN
(With Wiper)
Medium
Cutting
*
*
*
*
CCET21.5V0RSN
CCET060200R-SN
21.5V0LSN
060200L-SN
21.5V3RSN
0602V3R-SN
21.5V3LSN
0602V3L-SN
21.50.2RSN
060201R-SN
21.50.2LSN
060201L-SN
21.50.5RSN
060202R-SN
21.50.5LSN
060202L-SN
21.51RSN
060204R-SN
21.51LSN
060204L-SN
32.5V0RSN
09T300R-SN
32.5V0LSN
09T300L-SN
32.5V3RSN
09T3V3R-SN
32.5V3LSN
09T3V3L-SN
32.50.2RSN
09T301R-SN
32.50.2LSN
09T301L-SN
32.50.5RSN
09T302R-SN
32.50.5LSN
09T302L-SN
32.51RSN
09T304R-SN
32.51LSN
09T304L-SN
CCGT21.5V3RSN
CCGT0602V3R-SN
21.50.2RSN
060201R-SN
21.50.2LSN
060201L-SN
21.50.5RSN
060202R-SN
21.50.5LSN
060202L-SN
32.5V3RSN
09T3V3R-SN
32.5V3LSN
09T3V3L-SN
32.50.2RSN
09T301R-SN
32.50.2LSN
09T301L-SN
32.50.5RSN
09T302R-SN
32.50.5LSN
09T302L-SN
32.51RSN
09T304R-SN
32.51LSN
09T304L-SN
CCET21.5V3RWSN CCET0602V3RW-SN
21.5V3LWSN
0602V3LW-SN
32.5V3RWSN
09T3V3RW-SN
32.5V3LWSN
09T3V3LW-SN
.0012
.0012
.004
.004
.008
.008
.016
.016
.0012
.0012
.004
.004
.008
.008
.016
.016
.0012
.004
.004
.008
.008
.0012
.0012
.004
.004
.008
.008
.016
.016
.0012
.0012
.0012
.0012
Applicable
Holder Page
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
POSI
7
WITH
HOLE
C030
D008
D012
E006
E012
E013
C030
D008
D012
E006
E012
E013
C030
D008
D012
E006
E012
E013
*Please refer to page A028 before using the R/LWSN breaker (wiper insert).
CHIP BREAKER
A054
IDENTIFICATION
A002
A105
CC
Standard
Work
Material
Medium Cutting
Standard
Feed (inch/rev)
P
M
K
N
S
Light Cutting
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Stable Cutting
General Cutting
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape

(inch)
SMG
CCGT21.50.5MSMG
21.51MSMG
CCGT060202M-SMG .008
060204M-SMG .016
C030
D008
D012
E006
E012
E013
Medium
Cutting
Flat Top CCMW21.50.5

21.51
32.51
32.52
431
432
433
CCGW21.5V0
Flat Top
21.5V5
32.5V0
32.5V5
A106
CCMW060202
060204
09T304
09T308
120404
120408
120412
CCGW060200
0602V5
09T300
09T3V5
.008
.016
a a
.016
a a
.031
a a
.016
a a
.031
a a
.047
r s
s
s
.002
.002

a
r
Applicable
Holder Page
POSI
7
Standard
Size
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Finish Cutting
Depth of Cut (inch)
TURNING INSERTS
80
CCGT 2 1.5 0.5M SMG
TYPE INSERTS
WITH HOLE
C030
D008
D012
E006
E012
E013
C030
D008
D012
E006
E012
E013
CHIP BREAKER
A054
CP

Mild Steel
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
Feed (inch/rev)
POSI
11
Feed (inch/rev)
Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
(inch)
FV
R/L F
Finish
Cutting
CPMH2.51.50.5FV
2.51.51FV
320.5FV
321FV
322FV
CPMH2.51.51RF
2.51.51LF
321RF
321LF
R/L F
CPGT2.51.51RF
2.51.51LF
320.5RF
320.5LF
321RF
Finish
Cutting
321LF
CPMT21.50.5SQ
SQ
21.51SQ
21.52SQ
32.50.5SQ
32.51SQ
Finish
Cutting
32.52SQ
Standard CPGT2.51.50.5
2.51.51
320.5
321
Finish
Cutting
SV
Light
Cutting
WITH
HOLE
Unstable Cutting
CPMH2.51.50.5SV
2.51.51SV
320.5SV
321SV
322SV
CPMH080202-FV
080204-FV
090302-FV
090304-FV
090308-FV
CPMH080204R-F
080204L-F
090304R-F
090304L-F
.008
a s
.016
a s
.008
a s
.016
a s
.031
CPGT080204R-F
080204L-F
090302R-F
090302L-F
090304R-F
090304L-F
CPMT060202-SQ
060204-SQ
060208-SQ
09T302-SQ
09T304-SQ
09T308-SQ
CPGT080202
080204
090302
090304
.016
.016
.008
.008
.016
.016
CPMH080202-SV
080204-SV
090302-SV
090304-SV
090308-SV
.008
s a
s a
.016
s a
s a
.008
s a
s a
.016
s a
s a
.031
s a
s a
E006
a s
.016
.016
.016
.016
.008
.016
Applicable
Holder Page
Work
Material
Medium Cutting
P
M
K
N
S
Light Cutting
Finish Cutting
Feed (inch/rev)

TURNING INSERTS
80
CPMH 2.5 1.5 0.5 FV
TYPE INSERTS
WITH HOLE
E006

s
a
a
.031
.008
.016
.031
.008
.016
.008
.016
E006
CHIP BREAKER
A060
IDENTIFICATION
A002
A107
CP

Mild Steel
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Work
Material
P
M
K
N
S
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)

Feed (inch/rev)
Stable Cutting
General Cutting
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape

Light Cutting
Finish Cutting
Depth of Cut (inch)
POSI
11
Size
(inch)
MV
Medium
Cutting
MQ
Medium
Cutting
Standard
Medium
Cutting
A108
CPMH2.51.51MV
2.51.52MV
321MV
322MV
CPMH080204-MV
080208-MV
090304-MV
090308-MV
.016
a a
s a
.031
a a
s a
.016
a a
s a
.031
a a
s a
CPMT21.51MQ
21.52MQ
32.51MQ
32.52MQ
CPMT060204-MQ
060208-MQ
09T304-MQ
09T308-MQ
.016
.031
.016
.031
CPMX2.51.51
2.51.52
321
322
CPMX080204
080208
090304
090308
.016
a r
s s
.031
a r
s s
.016
a s
s s
.031
a s
s s

a
r
Applicable
Holder Page
TURNING INSERTS
80
CPMH 2.5 1.5 1 MV
TYPE INSERTS
WITH HOLE
E006
CHIP BREAKER
E006
A060

Standard
Standard
Feed (inch/rev)
Light Cutting
POSI
7
Feed (inch/rev)
Feed (inch/rev)
Stable Cutting
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Order Number
Carbide
(inch)
FV
Finish
Cutting
FJ
Finish
Cutting
FJ-P
Finish
Cutting
AZ
Finish
Cutting
R/L F
Finish
Cutting
WITH
HOLE
Steel
Coated
Shape
Unstable Cutting
DCMT21.50.5FV
21.51FV
21.52FV
32.50.5FV
32.51FV
32.52FV
DCGT21.5V5FJ
21.50.2FJ
21.50.5FJ
32.5V5FJ
32.50.2FJ
32.50.5FJ
DCGT21.5V5FJ-P
21.50.2FJ-P
21.50.5FJ-P
32.5V5FJ-P
32.50.2FJ-P
32.50.5FJ-P
DCGT21.50.5AZ
21.51AZ
32.50.5AZ
32.51AZ
32.52AZ
DCGT21.50.5RF
21.50.5LF
21.51RF
21.51LF
32.50.5RF
32.50.5LF
32.51RF
32.51LF
DCMT070202-FV
070204-FV
070208-FV
11T302-FV
11T304-FV
11T308-FV
DCGT0702V5-FJ
070201-FJ
070202-FJ
11T3V5-FJ
11T301-FJ
11T302-FJ
DCGT0702V5-FJ-P
070201-FJ-P
070202-FJ-P
11T3V5-FJ-P
11T301-FJ-P
11T302-FJ-P
DCGT070202-AZ
070204-AZ
11T302-AZ
11T304-AZ
11T308-AZ
DCGT070202R-F
070202L-F
070204R-F
070204L-F
11T302R-F
11T302L-F
11T304R-F
11T304L-F
.008
s a
s a
.016
s a
s a
.031
a s
.008
a s
.016
s a
s a
.031
s a
s a
.002
.004
.008
.002
.004
.008
C031
C032
D009
D013
D039
D040
E008
E013
E014
C031
C032
D009
D013
D039
D040
E008
E013
E014
.002
.004
.008
.002
.004
.008
.008
.016
.008
.016
.031
Applicable
Holder Page
Work
Material
Medium Cutting
Standard
P
M
K
N
S
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Finish Cutting

TURNING INSERTS
DC
55
DCMT 2 1.5 0.5 FV
TYPE INSERTS
WITH HOLE
.008
.008
.016
.016
.008
.008
.016
.016
C031
C032
D009
D013
D039
D040
E008
E013
E014
C031
C032
D009
D013
D039
D040
E008
E013
E014
C031
C032
D009
D013
D039
D040
E008
E013
E014
CHIP BREAKER
A054
IDENTIFICATION
A002
A109
DC

Depth of Cut (inch)
Standard
POSI
7
Standard
Feed (inch/rev)
Light Cutting
Medium Cutting
Standard
Feed (inch/rev)
Feed (inch/rev)
Work
Material
WITH
HOLE
P
M
K
N
S

Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
(inch)
SV
Light
Cutting
R/L SS
Light
Cutting
MJ
DCMT21.50.5SV
21.51SV
21.52SV
32.50.5SV
32.51SV
32.52SV
DCGT21.5V3RSS
21.5V3LSS
21.50.2RSS
21.50.2LSS
21.50.5RSS
21.50.5LSS
32.5V3RSS
32.50.2RSS
32.50.5RSS
DCGT21.51MJ
32.51MJ
32.52MJ
DCMT070202-SV
070204-SV
070208-SV
11T302-SV
11T304-SV
11T308-SV
DCGT0702V3R-SS
0702V3L-SS
070201R-SS
070201L-SS
070202R-SS
070202L-SS
11T3V3R-SS
11T301R-SS
11T302R-SS
DCGT070204-MJ
11T304-MJ
11T308-MJ
DCGT21.51MJ-P
32.51MJ-P
32.52MJ-P
DCGT070204-MJ-P .016
11T304-MJ-P .016
11T308-MJ-P .031
.008
r a
s a
s a
.016
s a
s a
s a
.031
s a
s a
s a
.008
s a
s a
s a
.016
s a
s a
s a
.031
s a
s a
s a
.0012
.0012
.004
.004
.008
.008
.0012
.004
.008
C031
C032
D009
D013
D039
D040
E008
E013
E014
C031
C032
D009
D013
D039
D040
E008
E013
E014
.016
.016
.031
C031
C032
D009
D013
D039
D040
E008
E013
E014
Medium
Cutting
MJ-P
a
a
a
Medium
Cutting
Standard DCMT21.50.5
Medium
Cutting
A110
21.51
21.52
32.50.5
32.51
DCMT070202
070204
070208
11T302
11T304
.008
a a
.016
a a a
.031
.008
a a
.016
a a a

a
r
Applicable
Holder Page
Depth of Cut (inch)
Mild Steel
Finish Cutting
Depth of Cut (inch)
TURNING INSERTS
55
DCMT 2 1.5 0.5 SV
TYPE INSERTS
WITH HOLE
s a
s a
s a
s a
s a
C031
C032
D009
D013
D039
D040
E008
E013
E014
C031
C032
D009
D013
D039
D040
E008
E013
E014
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
C031
C032
D009
D013
D039
D040
E008
E013
E014
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
Applicable
Holder Page
Work
Material
Stable Cutting
Steel
(inch)
Standard DCMT32.52
Medium
Cutting
MV
Medium
Cutting
R/L SR
Medium
Cutting
R/L SN
Medium
Cutting
32.53
431
432
433
DCMT21.50.5MV
21.51MV
21.52MV
32.50.5MV
32.51MV
32.52MV
DCET21.5V3RSR
21.5V3LSR
21.50.2RSR
21.50.2LSR
21.50.5RSR
21.50.5LSR
21.51RSR
21.51LSR
32.5V3RSR
32.5V3LSR
32.50.2RSR
32.50.2LSR
32.50.5RSR
32.50.5LSR
32.51RSR
32.51LSR
DCET21.5V0RSN
21.5V0LSN
21.5V3RSN
21.5V3LSN
21.50.2RSN
21.50.2LSN
21.50.5RSN
21.50.5LSN
21.51RSN
21.51LSN
DCMT11T308
11T312
150404
150408
150412
DCMT070202-MV
070204-MV
070208-MV
11T302-MV
11T304-MV
11T308-MV
DCET0702V3R-SR
0702V3L-SR
070201R-SR
070201L-SR
070202R-SR
070202L-SR
070204R-SR
070204L-SR
11T3V3R-SR
11T3V3L-SR
11T301R-SR
11T301L-SR
11T302R-SR
11T302L-SR
11T304R-SR
11T304L-SR
DCET070200R-SN
070200L-SN
0702V3R-SN
0702V3L-SN
070201R-SN
070201L-SN
070202R-SN
070202L-SN
070204R-SN
070204L-SN
.031
a a a
.047
.016
a r s a
a s
s a
.031
a a
s a
.047
s r
.008
s a
s a
s a
.016
s a
a a
s a
.031
s a
a a
s a
.008
s a
a a
s a
.016
s a
a a
s a
.031
s a
a a
TURNING INSERTS
P
M
K
N
S
POSI
7
WITH
HOLE
C031
C032
D009
D013
D039
D040
E008
E013
E014
s a
.0012
.0012
.004
.004
.008
.008
.016
.016
.0012
.0012
.004
.004
.008
.008
.016
.016
.0012
.0012
.004
.004
.008
.008
.016
.016
C031
C032
D009
D013
D039
D040
E008
E013
E014
C031
C032
D009
D013
D039
D040
E008
E013
E014
CHIP BREAKER
A054
IDENTIFICATION
A002
A111
DC

Depth of Cut (inch)
Standard
POSI
7
Standard
Feed (inch/rev)
Medium Cutting
Light Cutting
Standard
Feed (inch/rev)
Feed (inch/rev)
Work
Material
WITH
HOLE
P
M
K
N
S

Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
(inch)
R/L SN
Medium
Cutting
R/L SN
Medium
Cutting
R/L WSN
(With Wiper)
Medium
Cutting
SMG
Medium
Cutting
*
*
*
*
DCET32.5V0RSN
32.5V0LSN
32.5V3RSN
32.5V3LSN
32.50.2RSN
32.50.2LSN
32.50.5RSN
32.50.5LSN
32.51RSN
32.51LSN
DCGT21.5V3RSN
21.50.2RSN
21.50.5RSN
21.50.5LSN
32.5V3RSN
32.5V3LSN
32.50.2RSN
32.50.2LSN
32.50.5RSN
32.50.5LSN
32.51RSN
32.51LSN
DCET21.5V3RWSN
21.5V3LWSN
32.5V3RWSN
32.5V3LWSN
DCET11T300R-SN
11T300L-SN
11T3V3R-SN
11T3V3L-SN
11T301R-SN
11T301L-SN
11T302R-SN
11T302L-SN
11T304R-SN
11T304L-SN
DCGT0702V3R-SN
070201R-SN
070202R-SN
070202L-SN
11T3V3R-SN
11T3V3L-SN
11T301R-SN
11T301L-SN
11T302R-SN
11T302L-SN
11T304R-SN
11T304L-SN
DCET0702V3RW-SN
0702V3LW-SN
11T3V3RW-SN
11T3V3LW-SN
.0012
.0012
.004
.004
.008
.008
.016
.016
.0012
.004
.008
.008
.0012
.0012
.004
.004
.008
.008
.016
.016
.0012
.0012
.0012
.0012
DCGT21.50.5MSMG DCGT070202M-SMG .008

21.51MSMG
070204M-SMG .016
32.50.5MSMG
11T302M-SMG .008
32.51MSMG
11T304M-SMG .016
a
a
a
a
*Please refer to page A028 before using the R/LWSN breaker (wiper insert).
A112
: Inventory maintained. s : Inventory maintained in Japan. r : Non stock, produced to order only.
Applicable
Holder Page
Depth of Cut (inch)
Mild Steel
Finish Cutting
Depth of Cut (inch)
TURNING INSERTS
55
DCET 3 2.5 V0 RSN
TYPE INSERTS
WITH HOLE
C031
C032
D009
D013
D039
D040
E008
E013
E014
C031
C032
D009
D013
D039
D040
E008
E013
E014
C031
D009
D013
D039
D040
E008
E014
C031
C032
D009
D013
D039
D040
E008
E013
E014
Unstable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
C031
C032
D009
D013
D039
D040
E008
E013
E014
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
General Cutting
Applicable
Holder Page
Work
Material
Stable Cutting
Steel
(inch)
Flat Top
Flat Top
DCMW21.50.5
21.51
32.51
32.52
431
432
DCGW21.5V0
21.5V5
32.5V0
32.5V5
DCMW070202
070204
11T304
11T308
150404
150408
DCGW070200
0702V5
11T300
11T3V5
.008
.016
s s
.016
s s
.031
s s
.016
.031
r r
s
r
.002
.002
TURNING INSERTS
P
M
K
N
S
POSI
7
WITH
HOLE
C031
C032
D009
D013
D039
D040
E008
E013
E014
CHIP BREAKER
A054
IDENTIFICATION
A002
A113

TURNING INSERTS
55
DE
TYPE INSERTS
WITH HOLE
Finish Cutting
DEGX 4 3 0.5 RF
Medium Cutting
Depth of Cut (inch)
Aluminum Alloy
POSI
20
Feed (inch/rev)
WITH
HOLE
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Order Number
(ISO) Number
Coated
Cermet Cermet
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
General Cutting
(inch)
R/L F
Finish
Cutting
R/L
Medium
Cutting
A114
DEGX430.5RF
430.5LF
431RF
431LF
DEGX150402R-F
150402L-F
150404R-F
150404L-F
.008
.008
.016
.016
DEGX430.5R
430.5L
431R
431L
432R
432L
DEGX150402R
150402L
150404R
150404L
150408R
150408L
.008
.008
.016
.016
.031
.031

a
r
CHIP BREAKER
Applicable
Holder Page
Work
Material
P
M
K
N
S
Stable Cutting
C041
C041
A062
Standard
Depth of Cut (inch)
Standard
Standard
Stable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Order Number
Carbide
(inch)
AZ
WITH
HOLE
Unstable Cutting
Steel
Coated
Shape
General Cutting
RCGT0803M0-AZ
10T3M0-AZ
RCGT0803M0-AZ
10T3M0-AZ
Applicable
Holder Page
Work
Material
P
M
K
N
S
POSI
7
Feed (inch/rev)
Feed (inch/rev)
Feed (inch/rev)
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel

TURNING INSERTS
RC
RCGT 08 03 MO AZ
TYPE INSERTS
WITH HOLE
C033
Finish
Cutting
Standard RCMT0602M0
0803M0
RCMT0602M0
0803M0
s a
s a
C033
Medium
Cutting
Standard RCMX1003M0
Medium
Cutting
RR
Heavy
Cutting
RBS
Heavy
Cutting
1204M0
1606M0
2006M0
2507M0
3209M0
RCMX1606M0-RR
2006M0-RR
2507M0-RR
3209M0-RR
RCMX1003M0
1204M0
1606M0
2006M0
2507M0
3209M0
RCMX1606M0-RR
2006M0-RR
2507M0-RR
3209M0-RR
RCMX1606M0-RBS RCMX1606M0-RBS
2006M0-RBS
2006M0-RBS
2507M0-RBS
2507M0-RBS
3209M0-RBS
3209M0-RBS
a a
s s
s s
s s
a a a
a s
s s s
s a
s a a s
s s
s s
s a a s
s s a s
s s s s
s s s
s s s
s s s
s s s
H012
CHIP BREAKER
A054
IDENTIFICATION
A002
A115
RG
Work
Material
P
M
K
N
S
RGGM 20 04 M0
TYPE INSERTS
WITH HOLE
Size
Stable Cutting
Unstable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Order Number
(ISO) Number
Coated
Cermet Cermet
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Shape
General Cutting
Steel
Coated
POSI
30

(inch)
WITH
HOLE
Standard
RGGM2004M0
RGGM2004M0
Applicable
Holder Page
TURNING INSERTS
C044
A116

a
r
CHIP BREAKER
A064
SC
Standard
Medium Cutting
Standard
POSI
7
Feed (inch/rev)
Feed (inch/rev)
Stable Cutting
Unstable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Order Number
Carbide
(inch)
FV
WITH
HOLE
Steel
Coated
Shape
General Cutting
SCMT32.51FV
SCMT09T304-FV
.016
s a
Applicable
Holder Page
Work
Material
P
M
K
N
S
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Finish Cutting

TURNING INSERTS
90
SCMT 3 2.5 1 FV
TYPE INSERTS
WITH HOLE
C034
E015
Finish
Cutting
Standard
Medium
Cutting
Flat Top
SCMT32.51
32.52
431
432
433
SCMW32.51
32.52
431
432
433
SCMT09T304
09T308
120404
120408
120412
SCMW09T304
09T308
120404
120408
120412
.016 s
a a
s a
a a a
s a
a s
s a
.031
a a a
s a
.047
.031
.016 s
C034
E015
.016
s s
.031
s s
.016
s s
.031
s s
.047
C034
E015
r
CHIP BREAKER
A054
IDENTIFICATION
A002
A117
SP

Depth of Cut (inch)
Standard
POSI
11
Standard
Standard
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Work
Material
P
M
K
N
S
Stable Cutting
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Order Number
(ISO) Number
Coated
Cermet Cermet
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
General Cutting
(inch)
Standard
Medium
Cutting
Flat Top
Flat Top
A118
SPMT321
322
421
422
SPMT090304
090308
120304
120308
.016
.031
.016
.031
SPMW321
322
421
422
SPMW090304
090308
120304
120308
.016
a s s
.031
s s s
.016
a a s
.031
a a s
SPGX321
322
421
422
SPGX090304
090308
120304
120308
.016
.031

s
s
s
.016
.031

a
r
Applicable
Holder Page
Depth of Cut (inch)
Mild Steel

Medium Cutting
Depth of Cut (inch)
TURNING INSERTS
90
SPMT 3 2 1
TYPE INSERTS
WITH HOLE
CHIP BREAKER
A060
TC

Standard
Standard
Medium Cutting
Standard
Feed (inch/rev)
Feed (inch/rev)
Stable Cutting
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Order Number
Carbide
(inch)
FV
WITH
HOLE
Steel
Coated
Shape
Unstable Cutting
TCMT21.51FV
32.51FV
TCMT110204-FV
16T304-FV
.016
s a
.016
s a
TCGT21.5V5FJ
21.50.2FJ
21.50.5FJ
32.5V5FJ
32.50.2FJ
32.50.5FJ
TCGT21.5V5FJ-P
21.50.2FJ-P
21.50.5FJ-P
32.5V5FJ-P
32.50.2FJ-P
32.50.5FJ-P
TCGT21.50.5AZ
21.51AZ
21.52AZ
32.50.5AZ
32.51AZ
32.52AZ
TCGT1.21V3LF
1.210.2LF
1.210.5RF
1.210.5LF
1.211RF
1.211LF
TCGT1102V5-FJ
110201-FJ
110202-FJ
16T3V5-FJ
16T301-FJ
16T302-FJ
TCGT1102V5-FJ-P
110201-FJ-P
110202-FJ-P
16T3V5-FJ-P
16T301-FJ-P
16T302-FJ-P
TCGT110202-AZ
110204-AZ
110208-AZ
16T302-AZ
16T304-AZ
16T308-AZ
TCGT0601V3L-F
060101L-F
060102R-F
060102L-F
060104R-F
060104L-F
.002
.004
.008
.002
.004
.008
Applicable
Holder Page
Work
Material
POSI
7
Feed (inch/rev)
P
M
K
N
S
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Finish Cutting

TURNING INSERTS
60
TCMT 2 1.5 1 FV
TYPE INSERTS
WITH HOLE
C035
E015
E016
Finish
Cutting
FJ
Finish
Cutting
FJ-P
Finish
Cutting
AZ
Finish
Cutting
R/L F
Finish
Cutting
C035
E015
E016
.002
.004
.008
.002
.004
.008
.008
.016
.031
.008
.016
.031
C035
E015
E016
a
r
.004
.008
.008
.016
.016
.0012
C035
E015
E016
E030
CHIP BREAKER
A054
IDENTIFICATION
A002
A119
TC

Depth of Cut (inch)
Standard
POSI
7
Standard
Feed (inch/rev)
Medium Cutting
Standard
Feed (inch/rev)
Feed (inch/rev)
Work
Material
Stable Cutting
General Cutting
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape

WITH
HOLE
P
M
K
N
S
Size
(inch)
MJ
TCGT21.51MJ
32.51MJ
32.52MJ
TCGT110204-MJ
16T304-MJ
16T308-MJ
TCGT21.51MJ-P
32.51MJ-P
32.52MJ-P
TCGT110204-MJ-P .016
16T304-MJ-P .016
16T308-MJ-P .031
.016
.016
.031
Applicable
Holder Page
Depth of Cut (inch)
Mild Steel
Finish Cutting
Depth of Cut (inch)
TURNING INSERTS
60
TCGT 2 1.5 1 MJ
TYPE INSERTS
WITH HOLE
C035
E015
E016
Light
Cutting
MJ-P
a
a
a
C035
E015
E016
Light
Cutting
Standard
Medium
Cutting
Flat Top
A120
TCMT1.51.51
1.81.51
21.50.5
21.51
21.52
2.520.5
2.521
32.51
32.52
32.53
TCMW21.51
2.521
32.51
32.52
TCMT080204
090204
110202
110204
110208
130302
130304
16T304
16T308
16T312
TCMW110204
130304
16T304
16T308
.016
r a
.016
a a
s a
.008
a s
s a
.016
a a a
s a
.031
a a
C035
E015
E016
.008
r a
.016
a r
s a
.016
a a a
s a
.031
a a a
s a
.047
s
s s
.016
a a
.031
a a
.016
.016

a
r
CHIP BREAKER
C035
E015
E016
A054
TE

Medium Cutting
Depth of Cut (inch)
Aluminum Alloy
TURNING INSERTS
60
TEGX 3 2 0.5 R
TYPE INSERTS
WITH HOLE
POSI
20
Feed (inch/rev)
Unstable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Order Number
Coated
Cermet Cermet
(inch)
R/L
Medium
Cutting
WITH
HOLE
Steel
Coated
Shape
General Cutting
TEGX320.5R
320.5L
321R
321L
322R
322L
TEGX160302R
160302L
160304R
160304L
160308R
160308L
.008
.008
.016
.016
.031
.031
Applicable
Holder Page
Work
Material
P
M
K
N
S
Stable Cutting
C042
E028
CHIP BREAKER
A064
IDENTIFICATION
A002
A121
TP

Mild Steel
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Work
Material
P
M
K
N
S
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)

Feed (inch/rev)
Stable Cutting
General Cutting
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape

Light Cutting
Finish Cutting
Depth of Cut (inch)
POSI
11
Size
(inch)
FV
TPMH1.51.50.5FV
1.51.51FV
1.81.50.5FV
1.81.51FV
220.5FV
221FV
222FV
320.5FV
321FV
322FV
R/L FS TPGH1.51.50.5RFS
1.51.50.5LFS
1.51.51RFS
1.51.51LFS
1.81.50.5RFS
1.81.50.5LFS
1.81.51RFS
1.81.51LFS
220.5RFS
220.5LFS
221RFS
221LFS
321RFS
321LFS
322RFS
Finish
Cutting
322LFS
A122
TPMH080202-FV
080204-FV
090202-FV
090204-FV
110302-FV
110304-FV
110308-FV
160302-FV
160304-FV
160308-FV
TPGH080202R-FS
080202L-FS
080204R-FS
080204L-FS
090202R-FS
090202L-FS
090204R-FS
090204L-FS
110302R-FS
110302L-FS
110304R-FS
110304L-FS
160304R-FS
160304L-FS
160308R-FS
160308L-FS
.008
a s
.016
a s
.008
a s
.016
a s
.008
a s
.016
a s
.031
a s
.008
a s
.016
a s
.031
a s
.008
.008
.016
.016
.008
.008
.016
.016
.008
.008
.016
.016
.016
.016
.031
.031

a
r
Applicable
Holder Page
TURNING INSERTS
60
TPMH 1.5 1.5 0.5 FV
TYPE INSERTS
WITH HOLE
E007
E007
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
Steel
(inch)
R/L
Finish
Cutting
SQ
Finish
Cutting
Finish
Cutting
SV
Light
Cutting
TPGX1.51.50.5R
1.51.50.5L
1.51.51R
1.51.51L
1.81.50.5R
1.81.50.5L
1.81.51R
1.81.51L
1.81.52R
1.81.52L
220.5R
220.5L
221R
221L
222R
222L
TPMT1.81.51SQ
21.50.5SQ
21.51SQ
21.52SQ
32.51SQ
32.52SQ
TPMX1.51.50.5L
1.51.51L
1.81.51L
221L
TPGX080202R
080202L
080204R
080204L
090202R
090202L
090204R
090204L
090208R
090208L
110302R
110302L
110304R
110304L
110308R
110308L
TPMT090204-SQ
110202-SQ
110204-SQ
110208-SQ
16T304-SQ
16T308-SQ
TPMX080202L
080204L
090204L
110304L
.008
TPMH1.51.50.5SV
1.51.51SV
1.81.50.5SV
1.81.51SV
220.5SV
221SV
222SV
320.5SV
321SV
322SV
TPMH080202-SV
080204-SV
090202-SV
090204-SV
110302-SV
110304-SV
110308-SV
160302-SV
160304-SV
160308-SV
.008
s a
s a
.016
s a
s a
.008
s a
s a
.016
s a
s a
.008
s a
s a
.016
s a
s a
.031
s a
s a
.008
s a
s s
.016
s a
s s
.031
s a
s s
Applicable
Holder Page
Work
Material
Stable Cutting
TURNING INSERTS
P
M
K
N
S
.008
.016
s s
.016
s s
.008
.008
s r a
.016
s s
s r a
.016
s s
.031
.031
s s
.008
.008
s s a
s
s s s
.016
s s
.016
s s
.031
.031
s s
s s a
.016
POSI
11
WITH
HOLE
r s s
.008
.016
.031
.016
.031
.008
.016
.016
.016
E007
CHIP BREAKER
A060
IDENTIFICATION
A002
A123
TP

Mild Steel
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Work
Material
P
M
K
N
S
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)

Feed (inch/rev)
Stable Cutting
General Cutting
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape

Light Cutting
Finish Cutting
Depth of Cut (inch)
POSI
11
Size
(inch)
MV
TPMH1.51.50.5MV
1.51.51MV
1.81.50.5MV
1.81.51MV
1.81.52MV
220.5MV
221MV
222MV
321MV
Medium
Cutting
322MV
TPMT 1.81.51MQ
MQ
21.51MQ
21.52MQ
32.51MQ
Medium
Cutting
32.52MQ
Standard TPMX221
222
TPMH080202-MV
080204-MV
090202-MV
090204-MV
090208-MV
110302-MV
110304-MV
110308-MV
160304-MV
160308-MV
TPMT090204-MQ
110204-MQ
110208-MQ
16T304-MQ
16T308-MQ
TPMX110304
110308
.008
a a
s a
.016
a a
s a
.008
a a
s a
.016
a a
s a
.031
.008
s a
s a
.016
a a
s a
.031
a a
s a
.016
a a
s s
.031
a a
s s
.016
Applicable
Holder Page
TURNING INSERTS
60
TPMH 1.5 1.5 0.5 MV
TYPE INSERTS
WITH HOLE
E007
.016
.031
.016
.031
.016
s a
.031
s a

Medium
Cutting
Flat Top TPGX1.51.50.5

1.51.51
1.51.52
1.81.50.5
1.81.51
1.81.52
220.5
221
222
321
322
A124
TPGX080202
080204
080208
090202
090204
090208
110302
110304
110308
160304
160308
.008
s s s
.031
.008
.016
s s
.031
s s
a s a
.008
s s s
.031
s s
a s a
.016
r s
.031
.016

a
r
.016
a s a
CHIP BREAKER
A060
VB

Mild Steel
Finish Cutting
POSI
5
Feed (inch/rev)
Stable Cutting
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Order Number
Carbide
(inch)
FV
FJ
WITH
HOLE
Steel
Coated
Shape
Unstable Cutting
VBMT221FV
222FV
331FV
332FV
VBMT110304-FV
110308-FV
160404-FV
160408-FV
.016
a s
.031
a s
.016
a s
.031
a s
VBGT33V5FJ
330.2FJ
330.5FJ
VBGT1604V5-FJ
160401-FJ
160402-FJ
.002
.004
.008
VBGT33V5FJ-P
330.2FJ-P
330.5FJ-P
VBGT1604V5-FJ-P .002
160401-FJ-P .004
160402-FJ-P .008
VBGT220.5RF
220.5LF
221RF
221LF
330.5RF
330.5LF
331RF
331LF
VBMT221SV
222SV
331SV
332SV
VBGT110302R-F
110302L-F
110304R-F
110304L-F
160402R-F
160402L-F
160404R-F
160404L-F
VBMT110304-SV
110308-SV
160404-SV
160408-SV
Applicable
Holder Page
Work
Material
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)
Feed (inch/rev)
P
M
K
N
S
Feed (inch/rev)
Light Cutting

TURNING INSERTS
35
VBMT 2 2 1 FV
TYPE INSERTS
WITH HOLE
C028
C029
D010
D011
D014
D015
E009
E010
H013
C028
C029
H013
Finish
Cutting
FJ-P
a
a
a
C028
C029
H013
Finish
Cutting
R/L F
Finish
Cutting
SV
Light
Cutting
.008
.008
.016
.016
.008
.008
.016
.016
.016
.031
.016
.031
C028
C029
D010
D011
D014
D015
E009
E010
H013
C028
C029
D010
D011
D014
D015
E009
E010
H013
CHIP BREAKER
A050
IDENTIFICATION
A002
A125
VB

Mild Steel
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Work
Material
P
M
K
N
S
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)

Feed (inch/rev)
Depth of Cut (inch)
POSI
5
Light Cutting
Finish Cutting
Stable Cutting
General Cutting
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
MJ

(inch)
MJ
VBGT331MJ
332MJ
VBGT160404-MJ
160408-MJ
VBGT331MJ-P
332MJ-P
VBGT160404-MJ-P .016
160408-MJ-P .031
VBMT221MV
222MV
331MV
332MV
VBMT110304-MV
110308-MV
160404-MV
160408-MV
.016
a a
s a
.031
a a
s a
.016
a a
s a
.031
a a
s a
VBMT331
332
VBMT160404
160408
.016
.031
a a
VBET22V3RSR
22V3LSR
220.2RSR
220.2LSR
220.5RSR
220.5LSR
221RSR
221LSR
VBET1103V3R-SR
1103V3L-SR
110301R-SR
110301L-SR
110302R-SR
110302L-SR
110304R-SR
110304L-SR
.0012
.0012
.004
.004
.008
.008
.016
.016
.016
.031
Applicable
Holder Page
TURNING INSERTS
35
VBGT 3 3 1
TYPE INSERTS
WITH HOLE
C028
C029
H013
Light
Cutting
MJ-P
a
a
C028
C029
H013
Light
Cutting
MV
Medium
Cutting
Standard
C028
C029
D010
D011
D014
D015
E009
E010
H013
C028
C029
H013
Medium
Cutting
R/L SR
Medium
Cutting
A126
C028
C029
D010
D011
D014
D015
E009
E010
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
(inch)
R/L SN
Medium
Cutting
R/L WSN
(With Wiper)
VBET22V0RSN
VBET110300R-SN
22V0LSN
110300L-SN
22V3RSN
1103V3R-SN
22V3LSN
1103V3L-SN
220.2RSN
110301R-SN
220.2LSN
110301L-SN
220.5RSN
110302R-SN
220.5LSN
110302L-SN
221RSN
110304R-SN
221LSN
110304L-SN
VBET22V3RWSN VBET1103V3RW-SN
22V3LWSN
1103V3LW-SN
.0012
.0012
.004
.004
.008
.008
.016
.016
.0012
.0012
Applicable
Holder Page
Work
Material
Stable Cutting
Steel
TURNING INSERTS
P
M
K
N
S
POSI
5
WITH
HOLE
C028
C029
D010
D011
D014
D015
E009
E010
C028
C029
D010
D011
D014
D015
E009
E010
Medium
Cutting
Please refer to page A028 before using the R/LWSN breaker (wiper insert).
CHIP BREAKER
A050
IDENTIFICATION
A002
A127
VC
Standard
Feed (inch/rev)
Standard
Feed (inch/rev)
Work
Material
Stable Cutting
General Cutting
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape

Medium Cutting
Light Cutting
Feed (inch/rev)
WITH
HOLE
P
M
K
N
S
Size
(inch)
FV
Finish
Cutting
AZ
Finish
Cutting
R/L F
Finish
Cutting
SV
VCMT1.51.50.5FV
1.51.51FV
331FV
332FV
VCMT080202-FV
080204-FV
160404-FV
160408-FV
.008
a s
.016
a s
.016
s a
s a
.031
s a
s a
VCGT331AZ
332AZ
333AZ
43.57.5AZ
VCGT160404-AZ
160408-AZ
160412-AZ
220530-AZ
.016
.031
.047
.118
VCGT1.51.50.5RF
1.51.50.5LF
1.51.51RF
1.51.51LF
VCGT080202R-F
080202L-F
080204R-F
080204L-F
.008
.008
.016
.016
VCMT1.51.50.5SV
1.51.51SV
VCMT080202-SV
080204-SV
.008
.016
Applicable
Holder Page
POSI
7
Standard
VCMT 1.5 1.5 0.5 FV
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Finish Cutting
Depth of Cut (inch)
TURNING INSERTS
35
TYPE INSERTS
WITH HOLE
C036
E009
E010
E016
E017
C036
E016
E017
E009
E010
E009
E010
Light
Cutting
Standard VCMT221
Medium
Cutting
MV
331
332
333
VCMT1.51.50.5MV
1.51.51MV
VCMT110304
160404
160408
160412
.016
a a
s a
.016
a a a
s a
.031
a a a
s a
.047
a a
s a
VCMT080202-MV
080204-MV
.008
a a
s a
.016
a a
s a
C036
E016
E017
E009
E010
Medium
Cutting
A128

Unstable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Order Number
(ISO) Number
Coated
Cermet Cermet
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
General Cutting
(inch)
Flat Top
VCMW221
331
332
VCMW110304
160404
160408
.016
.016
s s
.031
s s
Applicable
Holder Page
Work
Material
Stable Cutting
Steel
C036
E016
E017
CHIP BREAKER
A054
IDENTIFICATION
A002
TURNING INSERTS
P
M
K
N
S
POSI
7
WITH
HOLE
A129

TURNING INSERTS
35
VD
TYPE INSERTS
WITH HOLE
VDGX 3 2 0.5 R
Medium Cutting
Depth of Cut (inch)
Aluminum Alloy
POSI
15
Feed (inch/rev)
WITH
HOLE
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Order Number
(ISO) Number
Coated
Cermet Cermet
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
General Cutting
(inch)
R/L
Medium
Cutting
A130
VDGX320.5R
320.5L
321R
321L
VDGX160302R
160302L
160304R
160304L
.008
.008
.016
.016
CHIP BREAKER
Applicable
Holder Page
Work
Material
P
M
K
N
S
Stable Cutting
C043
A064
VP
35
VPET 1.5 1.5 0.2 LSRF


SMG
Depth of Cut (mm)
Carbon SteelAlloy Steel (180280HB)

Depth of Cut (mm)
SMG
SMG
SRF
SRF
SRF
Feed (mm/rev)
Feed (mm/rev)
Work
Material
P
M
K
N
S
POSI
11
Feed (mm/rev)
Stable Cutting
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Order Number
Carbide
(inch)
L/R SRF VPET1.51.50.2LSRF
SMG
WITH
HOLE
Steel
Coated
Shape
Unstable Cutting
VPET080201L-SRF .004
1.51.50.2RSRF
080201R-SRF .004
1.51.50.5LSRF
080202L-SRF .008
1.51.50.5RSRF
080202R-SRF .008
220.2LSRF
110301L-SRF .004
220.2RSRF
110301R-SRF .004
220.5LSRF
110302L-SRF .008
220.5RSRF
110302R-SRF .008
22V3LSRF
1103V3L-SRF .0012
22V3RSRF
1103V3R-SRF .0012
VPGT1.51.50.2MSMG VPGT080201M-SMG .004
1.51.50.5MSMG
080202M-SMG .004
220.2MSMG
110301M-SMG .004
220.5MSMG
110302M-SMG .004
Applicable
Holder Page
Depth of Cut (mm)
Mild Steel
TURNING INSERTS
TYPE INSERTS
WITH HOLE
a
a
a
a
D010
D014
D015
a
a
a
a
a
a
a
a
D010
D014
D015
a
a
CHIP BREAKER
A060
IDENTIFICATION
A002
A131
WB

Mild Steel
Depth of Cut (inch)
Depth of Cut (inch)

Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Feed (inch/rev)
Work
Material
P
M
K
N
S
Medium Cutting
Finish Cutting
Depth of Cut (inch)
POSI
5

Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
(inch)
R/L F
WBGT1.21V3LF
WBGT0201V3L-F
1.210.2LF
020101L-F
1.210.5LF
020102L-F
1.211LF
020104L-F
1.51.5V3LF
L302V3L-F
1.51.50.2LF
L30201L-F
1.51.50.5RF
L30202R-F
1.51.50.5LF
L30202L-F
1.51.51RF
L30204R-F
Finish
Cutting
1.51.51LF
L30204L-F
R/L MV WBMT1.51.50.5RMV WBMTL30202R-MV
1.51.50.5LMV
L30202L-MV
1.51.51RMV
L30204R-MV
1.51.51LMV
L30204L-MV
Medium
Cutting
.0012
.004
.008
.016
.0012
.004
.008
.008
.016
.016
Applicable
Holder Page
TURNING INSERTS
80
WBGT 1.2 1 V3 LF
TYPE INSERTS
WITH HOLE
E009
E029
.008
a a
s a
.008
a a
s a
.016
a a
s a
.016
a a
s a
E009
E029
A132

CHIP BREAKER
A050
WC
Standard
Depth of Cut (inch)
Standard
Standard
Feed (inch/rev)
Feed (inch/rev)
Stable Cutting
Unstable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Order Number
Carbide
(inch)
FJ
Finish
Cutting
FJ-P
Finish
Cutting
R/L
Finish
Cutting
MJ
WITH
HOLE
Steel
Coated
Shape
General Cutting
WCGT21.5V5FJ
21.50.2FJ
21.50.5FJ
32.5V5FJ
32.50.2FJ
32.50.5FJ
WCGT21.5V5FJ-P
21.50.2FJ-P
21.50.5FJ-P
32.5V5FJ-P
32.50.2FJ-P
32.50.5FJ-P
WCGT1.210.5R
1.210.5L
1.211R
1.211L
1.51.50.5R
1.51.50.5L
1.51.51R
1.51.51L
WCGT21.51MJ
32.51MJ
32.52MJ
WCGT0402V5-FJ
040201-FJ
040202-FJ
06T3V5-FJ
06T301-FJ
06T302-FJ
WCGT0402V5-FJ-P
040201-FJ-P
040202-FJ-P
06T3V5-FJ-P
06T301-FJ-P
06T302-FJ-P
WCGT020102R
020102L
020104R
020104L
L30202R
L30202L
L30204R
L30204L
WCGT040204-MJ
06T304-MJ
06T308-MJ
WCGT21.51MJ-P
32.51MJ-P
32.52MJ-P
WCGT040204-MJ-P .016
06T304-MJ-P .016
06T308-MJ-P .031
.002
.004
.008
.002
.004
.008
Applicable
Holder Page
Work
Material
POSI
7
Feed (inch/rev)
P
M
K
N
S
Medium Cutting
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel

TURNING INSERTS
80
WCGT 2 1.5 V5 FJ
TYPE INSERTS
WITH HOLE
C037
E017
020
.002
.004
.008
.002
.004
.008
C037
E017
020
.008
.008
.016
.016
.008
.008
.016
.016
.016
.016
.031
E017
020
C037
E017
020
Light
Cutting
MJ-P
a
a
a
C037
E017
020
Light
Cutting
CHIP BREAKER
A054
IDENTIFICATION
A002
A133
WC
Standard
Standard
Feed (inch/rev)
WITH
HOLE
Work
Material
P
M
K
N
S
Standard
Feed (inch/rev)
Feed (inch/rev)
Stable Cutting
General Cutting
Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Order Number
(ISO) Number
Coated
Cermet Cermet
Carbide
Corner
Radius
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape

(inch)
Standard
Medium
Cutting
A134
WCMT1.210.5
1.211
1.51.50.5
1.51.51
21.50.5
21.51
21.52
32.51
32.52
WCMT020102
020104
L30202
L30204
040202
040204
040208
06T304
06T308
.008
a a
s a
.016
a a
s a
.008
s a
.016
s a
.008
a a
s a
.016
a a
s a
.031
.016
a a
s a
.031
a a
s a

CHIP BREAKER
Applicable
Holder Page
POSI
7
Size
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
WCMT 1.2 1 0.5
Medium Cutting
Depth of Cut (inch)
TURNING INSERTS
80
TYPE INSERTS
WITH HOLE
C037
E017
020
A054
WP

Mild Steel
Finish Cutting
Medium Cutting
POSI
11
Feed (inch/rev)
Feed (inch/rev)
Feed (inch/rev)
Stable Cutting
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
(ISO) Number
Corner
Radius
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Order Number
Carbide
(inch)
R/L FS
WPGT21.50.5RFS
21.50.5LFS
21.51RFS
21.51LFS
321RFS
321LFS
322RFS
Finish
Cutting
322LFS
Standard WPGT21.50.5
21.51
320.5
321
Finish
Cutting
MV
Medium
Cutting
WITH
HOLE
Steel
Coated
Shape
Unstable Cutting
WPMT21.50.5MV
21.51MV
321MV
322MV
WPGT040202R-FS
040202L-FS
040204R-FS
040204L-FS
060304R-FS
060304L-FS
060308R-FS
060308L-FS
WPGT040202
040204
060302
060304
.008
.008
.016
.016
.016
.016
.031
.031
WPMT040202-MV
040204-MV
060304-MV
060308-MV
.008
a a
s a
.016
a a
s a
.016
a a
s a
.031
a a
s a
.008
.016
.008
.016
Applicable
Holder Page
Work
Material
P
M
K
N
S
Depth of Cut (inch)
Depth of Cut (inch)
Depth of Cut (inch)

TURNING INSERTS
80
WPGT 2 1.5 0.5 RFS
TYPE INSERTS
WITH HOLE
E009
E009
E009
CHIP BREAKER
A060
IDENTIFICATION
A002
A135
XC

Mild Steel
XCMT 2 2 0.5 SVX

Light Cutting
Depth of Cut (inch)
Depth of Cut (inch)
POSI
7
Feed (inch/rev)
Feed (inch/rev)
WITH
HOLE
Work
Material
P
M
K
N
S
Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
(inch)
SVX
XCMT220.5SVX
221SVX
222SVX
XCMT150302-SVX .008
150304-SVX .016
150308-SVX .031
Applicable
Holder Page
TURNING INSERTS
25
TYPE INSERTS
WITH HOLE
a
a
C038
Light
Cutting
A136
CHIP BREAKER
A054
Unstable Cutting
Steel
(Tangent Angle)
Stainless Steel
Cast Iron
Non-Ferrous Metal
Dimensions (inch)
Order Number
(ISO) Number
Corner
Radius
UTi20T
HTi10
Carbide
Shape
General Cutting
D1
L2
D4
L5
(inch)
RTG05A
06A
07A
08A
10A
RTG05A
06A
07A
08A
10A
a a
a a
.197
.236
.295
.295
.098
.138
.138
.138
a a
.276
.433
.138
.197
a a
a a
.315
.394
.433
.551
.177
.217
.197
.256
Applicable
Holder Page
Work
Material
P
M
K
N
S
Stable Cutting
TURNING INSERTS
RTG
TYPE INSERTS
WITHOUT HOLE
POSI
6
WITHOUT
HOLE
C045
CHIP BREAKER
A066
IDENTIFICATION
A002
A137
SP
Standard
POSI
11
Medium Cutting
Feed (inch/rev)
Standard
Feed (inch/rev)
WITHOUT
HOLE
Work
Material
P
M
K
N
S
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Finish Cutting

Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
(inch)
R/L
SPGR321R
321L
SPGR090304R
090304L
.016
.016
Applicable
Holder Page
TURNING INSERTS
90
SPGR 3 2 1 R
TYPE INSERTS
WITHOUT HOLE

Finish
Cutting
Standard
Light to Medium
Cutting
Flat Top
A138
SPMR321
322
421
422
423
SPMN321
322
421
422
423
432
433
434
532
533
631
632
633
634
SPMR090304
090308
120304
120308
120312
SPMN090304
090308
120304
120308
120312
120408
120412
120416
150408
150412
190404
190408
190412
190416
.016
a s
s a
.031
a a
s a
.016
a s
s s
.031
a a
a s
.047
s r
.016
a s
a s
s s
.031
.016
s r
.031
.047
.031
.047
.063
.031
.047
.016
.031
.047
a r
.063

s
a
General Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
Steel
(inch)
Flat Top
SPG321
322
323
421
422
423
431
432
433
434
531
532
533
630.5
631
632
633
SPGN090304
090308
090312
120304
120308
120312
120404
120408
120412
120416
150404
150408
150412
190402
190404
190408
190412
.016
.031
a s
.047
.031
.047
.016
.031
WITHOUT
HOLE
s
a
a
.063
.016
.031
.047
.008
.016
.031
.047
POSI
11
.016
.047
Applicable
Holder Page
Work
Material
Stable Cutting
TURNING INSERTS
P
M
K
N
S
CHIP BREAKER
A066
IDENTIFICATION
A002
A139
60
TC
TYPE INSERTS
WITHOUT HOLE
Work
Material
P
M
K
N
S
Stable Cutting
General Cutting
Unstable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Order Number
(ISO) Number
Coated
Cermet Cermet
Carbide
(inch)
WITHOUT
HOLE
Flat Top
A140
Corner
Radius
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Shape

Steel
Coated
POSI
7
TCG 1.2 1 1
TCG1.211
1.81.51
1.81.52
TCGN060104
090204
090208
.016
.016
.031

a
r
Applicable
Holder Page
TURNING INSERTS
TP
Standard
Feed (inch/rev)
Medium Cutting
Standard
POSI
11
Feed (inch/rev)
Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
(inch)
R/L
Finish
Cutting
Standard
Light to Medium
Cutting
Flat Top
WITHOUT
HOLE
Unstable Cutting
TPGR221R
221L
222L
321R
321L
322R
322L
TPMR1.81.50.5
1.81.51
1.81.52
220.5
221
222
321
322
323
TPMN221
222
223
321
322
323
324
325
332
431
432
433
434
435
TPGR110304R
110304L
110308L
160304R
160304L
160308R
160308L
TPMR090202
090204
090208
110302
110304
110308
160304
160308
160312
TPMN110304
110308
110312
160304
160308
160312
160316
160320
160408
220404
220408
220412
220416
220420
.016
.016
.031
.016
.016
.031
.031
.008
s a
.016
r r
.031
r r
.008
r r
s a
.016
a a
s a
.031
a s
s a
.016
a a
s a
.031
a a
s a
.047
a s
s a
.016
a r
s s
s s
.031
a r
s s
.047
.016
a r
s s
a s s
.031
a s
s s
a s s
a s a
.047
s r
s s
.063
.079
.031
.016
a s
.031
a a
.047
a a
.063
.079
Applicable
Holder Page
Work
Material
P
M
K
N
S
Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Finish Cutting

TURNING INSERTS
60
TPGR 2 2 1 R
TYPE INSERTS
WITHOUT HOLE
s a
r r
a s
CHIP BREAKER
A066
IDENTIFICATION
A002
A141
TP
Standard
POSI
11
Feed (inch/rev)
Medium Cutting
Feed (inch/rev)
Work
Material
Standard
WITHOUT
HOLE
P
M
K
N
S

Depth of Cut (inch)
Depth of Cut (inch)
Mild Steel
Finish Cutting
TPG 2 2 0.5
Stable Cutting
General Cutting
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Coated
Cermet Cermet
Order Number
(ISO) Number
Carbide
Corner
Radius
UE6105
UE6110
UE6020
UH6400
US7020
US735
US905
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
NX55
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9005
RT9010
Coated
Shape
Unstable Cutting
(inch)
Flat Top
A142
TPG220.5
221
222
320.5
321
322
323
324
331
332
431
432
433
TPGN110302
110304
110308
160302
160304
160308
160312
160316
160404
160408
220404
220408
220412
.008
.016
a s
s s a
.031
a s
s s a
.008
r s
.016
a s
s s a
a s
a s a
.047
.016
.031
r r
.016
.031
.047

a
r
.031
.063
Applicable
Holder Page
TURNING INSERTS
60
TYPE INSERTS
WITHOUT HOLE
CHIP BREAKER
A066
Memo
A143
GUIDE TO CBN & PCD TURNING INSERTS

zOrganized according to turning insert shape.
xInserts are arranged in order of :
Negative inserts (with hole|without hole)
Positive inserts (with hole|without hole)

General Cutting
INSERT DIMENSIONS
INSERT GRADES
STOCK STATUS
CBN TURNING INSERTS [NEGATIVE]
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Order Number
(ISO) Number
Corner
Radius
(inch)
NEW PETIT CUT
WITH
HOLE
NEW PETIT CUT
NEW PETIT CUT
(With breaker)
NEW PETIT CUT
B022
aTo
Coated
CBN
CBN
NP-CNGA431-GA4
432-GA4
433-GA4
431-GN4
432-GN4
433-GN4
431-FS4
432-FS4
433-FS4
431-TA4
432-TA4
433-TA4
NP-CNGA431-GAWS4
432-GAWS4
433-GAWS4
NP-CNGA120404GA4
120408GA4
120412GA4
120404GN4
120408GN4
120412GN4
120404FS4
120408FS4
120412FS4
120404TA4
120408TA4
120412TA4
NP-CNGA120404GAWS4
120408GAWS4
120412GAWS4
.016
BF-CNGG431-TA4
432-TA4
433-TA4
BF-CNGG120404TA4
120408TA4
120412TA4
.016
.031
.047
NP-CNGA431-GA2
432-GA2
433-GA2
431-GS2
432-GS2
433-GS2
431-GN2
432-GN2
433-GN2
431-FS2
432-FS2
433-FS2
431-TA2
432-TA2
433-TA2
431-TS2
432-TS2
433-TS2
NP-CNGA120404GA2
120408GA2
120412GA2
120404GS2
120408GS2
120412GS2
120404GN2
120408GN2
120412GN2
120404FS2
120408FS2
120412FS2
120404TA2
120408TA2
120412TA2
120404TS2
120408TS2
120412TS2
.016
a s
Applicable
Holder Page
Sintered Alloy
Shape
NEG
B000
H
K
S
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Work
Material
INSERTS
RBG TYPE
WITHOUT HOLE
Size Thickness Corner Radius Honing & Wiper

Please refer to page B002.
a s
.031
CBN
Work
Material
a s
.016
.031
.047
.016
.031
.047
.016
s s
.031
s s
.047
s s
.016
.031
.047
.031
Unstable Cutting
Order Number
RBG10
12
16
(ISO) Number
Dimensions (inch)
RBG10
12
16
D1
S1
L1
D4
.394
.197
.354
.197
.472
.236
.433
.236
.630
.315
.512
.315
WITHOUT
HOLE
C006
009
E021
E024
H006
008
INSERTS
RTG TYPE
WITHOUT HOLE
C006
009
E021
E024
H006
008
Work
Material
H
K
S
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
a s
.016
a a
.031
a a
.047
Shape
Order Number
(ISO) Number
a a
.016
.031
.047
Dimensions (inch)
CBN
a s
.047
.016
.031
.047
.016
a s
.031
a s
.047
a s
.016
.031
.047
RTG05A
06A
07A
08A
10A
C006
009
E021
E024
H006
008

<1 insert in one case>
a
r
B050
RTG05A
06A
07A
08A
10A
D1
S1
L1
D4
.197
.138
.295
.098
.236
.138
.295
.138
.276
.197
.433
.138
.315
.197
.433
.177
.394
.256
.551
.217

a
r
APPLICABLE HOLDER PAGE

indicates reference pages

for details of applicable holders.
PHOTO OF INSERT
INSERT CORNER RADIUS
PRODUCT NAME
INSERT NUMBER
Order:
General Cutting
Cast Iron
CBN
POSI
5
6
C006
009
E021
E024
H006
008
Stable Cutting
Hardened Materials
Shape
a s
.047
H
K
S
Applicable
Holder Page
CN
CBN
CBN TURNING INSERTS [POSITIVE]

NP-CNGA 4 3 1 GA4
80
TYPE INSERTS
WITH HOLE
Applicable
Holder Page
PRODUCT SECTION
INDICATION OF
NEGATIVE/POSITIVE
TYPE
TITLE OF PRODUCT
ACCORDING TO THE
INSERT TYPE
MB710
SHAPE &
ANGLE MARK
Unstable Cutting
MB825
Stable Cutting
FIGURE SHOWING INSERT GEOMETRY

Dimensions are detailed in the "Dimensions" column.
C045
TURNING
INSERT STANDARDS
INSERT GRADES
INDENTIFICATION .................................................... B002
CBN (CUBIC BORON NITRIDE) ............................... B004
PCD GRADE MD220 (SINTERED DIAMOND) ......... B015
CLASSIFICATION OF CBN & PCD INSERTS .......... B016
STANDARD OF CBN TURNING INSERTS
a
STANDARD OF PCD TURNING INSERTS

a
CNppTYPE ... RHOMBIC 80 ............. B022

DNppTYPE ... RHOMBIC 55 ............. B025

SNppTYPE ... SQUARE 90 .............. B055
TNppTYPE ... TRIANGULAR 60 ........ B055
VNppTYPE ... RHOMBIC 35 ............. B056

VNppTYPE ... RHOMBIC 35 ............. B032
WNppTYPE ... TRIGON 80 ............... B034
a

RNppTYPE ... ROUND .................... B036
a
SPppTYPE ... SQUARE 90 .............. B051

TBppTYPE ... TRIANGULAR 60 ........ B052
TPppTYPE ... TRIANGULAR 60 ........ B053
RBGppTYPE .............................. B050
RTGppTYPE .............................. B050
CCppTYPE ... RHOMBIC 80 ............. B038

CPppTYPE ... RHOMBIC 80 ............. B041
DCppTYPE ... RHOMBIC 55 ............. B042
T CppTYPE ... TRIANGULAR 60 ........ B044
T PppTYPE ... TRIANGULAR 60 ........ B045
VBppTYPE ... RHOMBIC 35 ............. B047
VCppTYPE ... RHOMBIC 35 ............. B048
WCppTYPE ... TRIGON 80 ............... B049
CCppTYPE ... RHOMBIC 80 ............. B058

CPppTYPE ... RHOMBIC 80 ............. B058
DCppTYPE ... RHOMBIC 55 ............. B059
S PppTYPE ... SQUARE 90 .............. B059
T CppTYPE ... TRIANGULAR 60 ........ B060
T PppTYPE ... TRIANGULAR 60 ........ B061
VBppTYPE ... RHOMBIC 35 ............. B063
VCppTYPE ... RHOMBIC 35 ............. B063
WCppTYPE ... TRIGON 80 ............... B064
WPppTYPE ... TRIGON 80 ............... B064
DEppTYPE ... RHOMBIC 55 ............. B065
T EppTYPE ... TRIANGULAR 60 ........ B065
VDppTYPE ... RHOMBIC 35 ............. B066
a
SPppTYPE ... SQUARE 90 .............. B067

TPppTYPE ... TRIANGULAR 60 ........ B067
B001
IDENTIFICATION
Symbol
Insert Shape
Square
Triangular
Rhombic 80
Rhombic 55
Rhombic 35
Trigon
Round
Triangular insert with a facet

(Secondary Cutting Edge)
c Symbol for Insert Shape
BM
With Breaker
BF
With Breaker
NP
New Petit Cut
No mark Standard Type

x Insert Geometry
Symbol
b Symbol for Tolerance Class
G
M*
Tolerance of Tolerance of
Tolerance of
Inscribed
Nose Height
Thickness
Circle
m (inch)
S1 (inch)
&D1 (inch)
.001
.001
.005
.003 .0063 .002 .003
.005
As a rule, the sides of these inserts are as sintered.

*Tolerance
differs with insert size. For the accuracy of
class M, refer to the table on the right.
10-inserts Package
Detail of M Class Insert Tolerance

of Nose Height m (inch)
a Tolerance
I.C.
Triangular Square

Round
80
55
35
.250 .003 .003 .003 .004 .0063

.375 .003 .003 .003 .004 .0063
.500 .005 .005 .005 .006

a Tolerance of Inscribed Circle & D1 (inch)
I.C.
Triangular Square

Round
80
55
35
.002 .002 .002 .002 .002

.002 .002 .002 .002 .002 .002
.003 .003 .003 .003

.003
.250
.375
.500
b Symbol for Tolerance Class
No mark 1-insert Package

z Insert Case
INCH
METRIC
n Symbol for Chipbreaker and Clamping System
v Symbol for Relief Angle

Symbol
Inch
Relief Angle
15
20
11
Special
Design
B002
Metric
I.C.
.250"
Hole
Chip
Figure I.C.
and over under .250" Symbol Hole Conguration Breaker Figure
A
With
+
One Countersink
With (40 60) One
Hole
Sided
With
+
One Countersink
With (70 90) One
Hole
Sided
Chip
Symbol Hole ConHole
guration Breaker Figure
A
With
Hole
Cylindrical
Hole
With
Hole
Cylindrical One
Hole
Sided
Without
Hole
No
No
Special
Design
Thickness is from the bottom of the insert

to the top of the cutting edge.
Inch
I.C. .250"
I.C.
and over under .250"
Inch
I.C.
I.C. .250" under
and over .250"
1.2 (5)
1.5 (6)
1.8 (7)
2
2.5
3
4
Diameter of
Inscribed
Circle
(inch)
Metric
.156
.187
.219
.250
.313
.375
.500
02
L3
03
04
05
06
08
09
12
08
09
11
13
16
22
04
05
06
07
09
11
15
03
04
05
06
08
09
12
03
04
05
06
07
09
12
06
08
09
11
13
16
22
Inch
0.5
Corner Radius
(inch)
.008
Metric
.016
04
02
.031
08
.047
12
.063
16
Wiper
WS
With Wiper
(For low rigidity work)
No mark
Without Wiper
Continuous Cutting
G
GA
GN
GS
General Cutting
T
TA
TS
TN
.055
S1
.063
01
1.1
.070
T0
1.5
.094
02
1.8
.109
T2
.125
03
2.5
.156
T3
.187
04
, Symbol for Insert Thickness
/ Application (Honing)
F
FA
FS
FN
FP
Metric
m Symbol for Insert Size
. Symbol for Insert Corner Conguration
0.9
Thickness
(inch)
Number of Teeth
2
No mark
Symbol for Cutting Direction

Figure
Hand Symbol
Right
Left
Neutral
Cutting Edge Angle
Interrupted Cutting
Please refer to page B011 for further

information.
91
93
No mark
Non Restriction
Please pay special attention when

using an wiper insert.
Please refer to page B014 for further
information.
B003
COATED CBN SERIES

BC8020 / MBC010 / MBC020
FEATURES
With the expansion of BC8020, Mitsubishi can offer 3 coated CBN grades
for machining of hardened steels. These 3 coated CBN grades cover a
wide range of applications.
To achieve longer tool life, Mitsubishi uses a unique "Particle-activated
Sintering Method", combined with increased cutting edge strength. With
high crater wear resistance CBN grades and a wear resistant ceramic
coatings, longer tool life and improved machine efciency are obtained.
Cutting Speed (SFM)
Heavy
Light
Light
Continuous
Cutting Mode
Grade
Grade Features and Application
High efciency coated CBN
BC8020
Incleased cutting edge strength and high crater wear resistant CBN grade in combination with a
highly wear resistant TiAlN coating, results in longer tool life and improved machining efciency
under heavy duty or interrupting cutting.
Coated CBN for general cutting
MBC020
Uses a CBN substrate that has high cutting edge toughness. The TiAlN based coating delivers
superb wear resistance. It covers a wide range of applications from continuous to light
interrupted cutting.
Coated CBN for High Speed Continuous Cutting
MBC010
MBC010 makes the best use of special ceramic binder structure, resulting in high wear resistance.
This enables continuous machining at high speed of over 985 SFM.
Heavy
Interrupted
Main
Component
Coating Layer
CBN(Medium Grain)
TiN
Al2O3
TiAlN
CBN (Micro Grain)

TiN
Al2O3
TiAlN
CBN (Micro Grain)

TiN
Al2O3
TiN
CUTTING PERFORMANCE
y Interrupted Cutting
Impact frequency before fracturing
Cutting Speed (SFM)
y Continuous Cutting
V-T Diagram (VB=.0039inch)
Number of Impacts
Cutting Time (min)
<Cutting Condition>
Workpiece : Hardened Steel (60HRC)
External Continuous Cutting
Insert
: NP-CNGA432GA
: .004IPR
Feed
Depth of Cut : .0039inch
Wet Cutting
B004
<Cutting Condition>
: Hardened Steel (60HRC)
Workpiece
External Interrupted Cutting. 8 Grooves
Insert
: NP-CNGA432GA
Cutting Speed : 490SFM
: .008IPR
Feed
Dry Cutting
NEW
BC8020
WEAR RESISTANCE
SURFACE ROUGHNESS
.0063
Flank Wear (inch)
.0047
Surface Roughness : Ra (!inch)
Fracture
Conventional Coated CBN
.0031
.0016
240
160
Cutting Time (min)
Cutting Time (min)
<Cutting Condition>
Workpiece : Hardened Steel (60HRC) Insert : NP-CNGA432GA
Cutting Speed : 490SFM Feed : .006IPR Depth of Cut : .020inch
Dry Continuous Cutting
y Interrupted Cutting (Crater wear)

Normal wear
FRACTURE RESISTANCE
BC8020
Conventional
Coated CBN
Workpiece
Medium Interrupted Cutting
Insert
: NP-CNGA432GA
Cutting speed : 490SFM
Feed
: .006IPR
Dry Interrupted Cutting
Fracturing from crater wear
5000
20000 22000 24000 26000 28000 30000

Number of Impacts
y Interrupted Cutting (Chipping)

Normal wear
FRACTURE RESISTANCE
BC8020
Conventional
Coated CBN
0
5000
10000
15000
Number of Impacts
20000
Workpiece
Insert
: NP-CNGA432GA
Feed
: .008IPR
25000
Chipping
BC8020 exhibits excellent cutting performance for severe or interrupted machining.

B005
MBC020
WEAR RESISTANCE
Conventional
Coated CBN A
Flank Wear (inch)
Conventional
Coated CBN B
Conventional
Coated CBN C
TOUGHNESS
Conventional
Coated CBN A
Conventional
Coated CBN B
Cutting Time (min)
Cutting Time (min)
Insert : NP-CNGA432-GA4
Feed : .004IPR
Insert : NP-CNGA432-GA
Feed : .006IPR
MBC020 exhibits excellent cutting performance for a wide range of applications

from continuous through interrupted machining.
MBC010
Fracture
Flank Wear (inch)
Conventional
Coated CBN A
Conventional
Coated CBN B
Cutting Time (min)
Insert : NP-CNGA432-GS2
Feed : .002IPR
SURFACE ROUGHNESS
Fracture
Surface Roughness : Ra (inch)
WEAR RESISTANCE
Conventional Coated CBN A
Large Wear
Conventional
Coated CBN B
Cutting Time (min)
Insert : NP-CNGA432-GS2
Feed : .006IPR
MBC010 employs TiN based coating for superior, consistent surface nishes.
B006
UNCOATED CBN SERIES

CBN tool material is produced by mixing the primary component
CBN (cubic boron nitride), which has a hardness second only
to diamond, with a special ceramic or metal binder. It is then
sintered at a pressure of over 5GPa and at a temperature of
2192F or higher.
CBN has lower afnity to iron than diamond. The low afnity
and high hardness properties means that sintered CBN
delivers superior cutting performance especially during
high speed machining of materials such hardened steel,
cast iron and sintered alloys.
Cutting Speed (inch)
FEATURES
Continuous
Light
Interrupted
Heavy
Cutting Mode
HARDENED STEEL MACHINING

Grade
Main
Component
General Purpose Turning
MB8025
By employing a "Particle-activated Sintering Method", the new sintered CBN technology is recommended for
continuous cutting from medium to high speeds.
For High Speed Continuous Cutting
MB810
CBN
TiN
Al2O3
It features improved wear resistance due to impregnation with larger CBN particles.
For Continuous to Medium Interrupted Cutting
MB825
Excellent balance of wear resistance and fracture resistance due to introduction of micro-grain CBN particles.
For Heavy Interrupted Cutting
MB835
CBN (Micro Grain)

TiN
Al2O3
Improved grade employing micro-grain CBN particles. Excellent fracture resistance for use in heavy interrupted
cutting.
CBN (Micro Grain)

TiC
Al2O3
CBN (Micro Grain)
TiN
Al2O3
CUTTING PERFORMANCE
y Interrupted Cutting
Impact frequency before fracturing
Cutting Speed (SFM)
Number of Impacts
Cutting Time (min)
<Cutting Condition>
Workpiece: Hardened steel
(60HRC)
: .004IPR
Feed

Wet Cutting
<Cutting Condition>
: .004IPR
Workpiece : Hardened steel
Feed
(60HRC)
External Interrupted Cutting 8 Groove Dry Cutting
B007
MB5015
NEW
For Cylinder liners

Produced to order only
FEATURES
aMB5015 is exclusive grade for boring of Centrifugal casting Cylinder liners in semi nishing or nishing applications with high wear
resistance.
RECOMMENDED CUTTING CONDITIONS

Cutting Speed (SFM)
Work Material
330
Centrifugal casting
Feed
(inch/rev)
Cutting Mode
Cast Iron
1640
3280
4920
Depth of Cut
(inch)
.012(Finishing) .002(Finishing)
Continuous cutting
.031(Semi-nishing) .008(Semi-nishing)
Coolant
Wet
CUTTING PERFORMANCE
VB wear
.014
Defective product
Flank Wear (inch)
.012
Conventional
Conventional
.008
.004
Number of Drilling
MB5015
Workpiece : FC200(Centrifugal casting)&63.0
Cutting Speed : 2625SFM Feed : .014IPR Depth of Cut : .0012inch
Work : Centrifugal casting Cylinder liner Hole Depth : 4inch
CAST IRON MACHINING

Main
Component
For General Cutting
MB710
General purpose grade with well

balanced wear and fracture
resistance.
For High Speed Continuous

Through Interrupted Cutting
MB730
Uses a metallic binder improving the

overall fracture resistance.
Large Depth of Cutting

High Efciency
MBS140
Solid CBN therefore no restriction on

depth of cut enabling high machining
efciency.
CUTTING PERFORMANCE
CBN
TiC
Al2O3
CBN
(High Content)
Co Base Alloy
Cutting Speed (SFM)
Grade
Ceramics
CBN
AIN
(Solid)
Cutting Time (min)
<Cutting Condition of MB710 >

Workpiece : AISI-35
Insert
: TNGA332
Feed
: .004IPR
Wet Cutting
B008
<Cutting Condition of Ceramics>

Workpiece : AISI-35
Insert
: TNGA332
: .004IPR
Feed
Dry Cutting
MB4020
SINTERED ALLOY MACHINING

FEATURES AND RECOMMENDED CUTTING CONDITIONS

For General Cutting
Work
Material
Cutting Speed (SFM)
High CBN content and a special binder to bind CBN particles

allows MB4020 to deliver long tool life for the machining of sintered
alloys. A general-purpose grade suitable for the machining of
various sintered alloys with different hardness, structures and
varied workpiece geometries.
Depth of Cut
Feed
(inch/rev)
(inch)
Cutting Speed (SFM)
General
Sintered Alloy
.008
.012
High Strength
Sintered Alloy
.008
.012
Continuous Cutting of
High Density
Sintered Alloy
.008
.012
Hardness of Workpiece (HRB)
CUTTING PERFORMANCE
y Continuous Cutting of High Density Sintered Alloy
y Continuous Cutting of Sintered Alloy
Surface Roughness Ra (!inch)
Surface Roughness Ra (!inch)
Conventional A
Fracture
Conventional B
Number of Wokepiece (pcs./corner)
Conventional A
Fracture
Fracture
Conventional B
Number of Wokepiece (pcs./corner)
Workpiece : High Strength Sintered Alloy Insert : NP-CNGA432
Cutting Speed : 620SFM Feed : .006IPR
Wet Cutting
Workpiece : Sintered Alloy Insert : NP-CNGA432
Cutting Speed : 330SFM Feed : .006IPR
Wet Cutting
APPLICATION EXAMPLE
NP-TNGA331-FS3
Insert
NP-TPGX1.51.51-FS3
Workpiece
Carburized and quenched alloy
Cutting Condition
Component
Cutting Speed
(SFM)
Carburized and quenched alloy
Variable valve parts
Oil pump parts
820
330
Feed
(IPR)
.004
.0012
Depth of Cut
(inch)
.008
.002
(pieces /
corner)
(pieces /
corner)
Results
Conventional
Conventional
B009
CBN
sintered ferrous alloy and cast iron.
a Low afnity to iron, thus good surface nishes are possible.
a Present grinding processes can now be machined reducing cost and time.
SELECTION STANDARD
Type
a Heat Treated Steel

Work Material
Recommended
Grade
Cutting Mode
MBC010
MBC020
High speed nish cutting
Coated
a Suitable for high speed nishing of heat treated steel,
High Alloy Steel
35 65
HRC
Heavy interrupted cutting for general purpose
BC8020
Interrupted cutting for general purpose
Non-coated
Structural Steel
Continuous cutting for general purpose
Continuous cutting
MB8025
Light interrupted cutting
MB810
MB825
MB835
High speed nish cutting

Continuous to medium interrupted cutting
Interrupted cutting
Recommended Cutting Condition

Cutting Speed (SFM)
Feed (IPR)
Depth of Cut (inch)
820 (490 1310)

655 (260 820)
655 (260 820)
490 (195 655)
590 (260 820)
390 (195 490)
655 (490 985)
390 (230 490)
330 (165 390)
.008
.008
.012
.008
.012
.008
.006
.012
.012
.008
.012
.030
.012
.020
.012
.006
.020
.020
a Cast Iron
Work Material
Workpiece
Structure
Gray Cast Iron
Alloy Cast Iron
Pearlitic
60-40-18
Ductile Cast Iron
100-70-03
Ferritic
Cutting Speed (SFM)

820
1640
2460
3280
4100
MBS140
Ferritic + Pearlitic
Pearlitic
MB710
MB730
MB710
MB730
Depth of Cut Coolant

(inch)
.039
.020 MBS140 Dry,Wet
.197
Feed
(IPR)
.016
.020
Dry,Wet
.016
.020
Dry,Wet
a Sintered Alloy
Work Material
General Sintered Alloy
High Density Sintered Alloy
Sintered Alloy
Recommended Grade
MB4020
MB4020
MB4020, MB835
Cutting Speed (SFM)

Feed (IPR)
Depth of Cut (inch)
820 (260 985)

490 (260 820)
330 (260 490)
.008
.008
.008
.012
.012
.012
a Valve Seat
Amount of Hard Particles
Hardness of Workpiece (HV)
None or Small
Large
150
250
300
350
Plunge Cut
MB730
MB825
MB835
Traverse Cut
MB730
MB710
MB825
a Roll
Cutting Speed (SFM)

Feed (IPR)
Depth of Cut (inch)
MB825, MB8025
260 (100 425)
.012 (.004 .020)
.008 .118
MB710
260 (100 425)
.012 (.004 .020)
.008 .118
MB825, MB8025
MB730
MB730, MBS140
260 (100 425)

165 (65 230)
65 (30 100)
.012 (.004 .020)

.010 (.004 .020)
.020
.008 .118
.004 .118
.008
Cutting Speed (SFM)

Feed (IPR)
Depth of Cut (inch)
390 (330 490)

230 (165 330)
.008
.008
.020
.020
Work Material
Grade
Cast Steel
Adamite Cast Steel
Ductile Cast Iron

Granular Cast Iron
Chilled Cast Iron
High Chromium Steel
High Alloy Steel
High Speed Steel

Cemented Carbide
a Heat Resistant Alloy

Work Material
Grade
Ni Base Alloy
MB730
MB730
Co Base Alloy
B010
HONING
For the CBN BC8020, MBC010 and MBC020 coated grades, MB4020 and MB710/MB730 a wide range of edge honing styles
are available to cover a large range of applications and to represent Mitsubishi Materials unique cutting tool technology.
St
ab
le
cu
ttin
g
a General cutting
GA honing is the rst recommendation.
GS honing if the depth of cut is .004 inch or more.
GN honing if crater wear is too large.
FS Honing
GA Honing
FA Honing
a Continuous cutting, stable cutting
FN Honing
GS Honing
GN Honing
1st Recommendation
(General cutting)
TA Honing
TS Honing
Un
sta
ble
TN Honing
NEW HONING TYPES
FA honing to improve the initial machining performance.

FS honing is the rst recommendation.
FN honing if crater wear is too large.
a Medium and heavy interrupted cutting, unstable cutting

TA honing is the rst recommendation.
TS honing if the depth of cut is .004 inch or more.
TN honing if crater wear is too large.
cu
ttin
g
NP-CNGA431- G A W2
Main Application
EDGE HONING
TYPE
MAIN
APPLICATION
For General
Purpose Machining
(1st recommendation)
Edge Honing Type
For Anti Chatter

(Sharp anti-burr type)
For Small
Depth of Cut
(Crater wear resistant)
FS Honing
FN Honing
GA Honing
For Continuous
G
Light Interrupted Machining
GS Honing
GN Honing
TFor Interrupted Machining TA Honing
TS Honing
TN Honing
FFor Continuous Machining
FA Honing
(Note) First, select the insert edge type from the main application area (F,G,T) then choose honing (A,S,N) that compliments the machining
requirement.
CONVENTIONAL HONING TYPES

Other than the new honing types, the three conventional honing types, F, G and T types are available for use in accordance to
the machining application.
NP-CNMA431- G 2
St
ab
le
cu
ttin
g
F HONING
F Honing
For stable continuous cutting.
G Honing
GHONING
For general purpose cutting.

(Including light to medium interrupted cutting).
T Honing
1st Recommendation
(General cutting)
Honing Type
Un
sta
ble
cu
ttin
g
T HONING
For medium to heavy interrupted cutting.
B011
CBN GROOVING SERIES

GY
FEATURES
a Combined with a High-rigidity Holder Ensures High Accuracy and
Long Tool Life.

Holder rigidity is essential when grooving hardened steel.
The GY series Tri Lock system offers high rigidity equivalent to a 1-piece type tool
holder despite being a modular system.
CUTTING PERFORMANCE
y Tool life
Competitor B
Flank Wear (inch)
Insert Width (inch)
.197
.187
.157
.125
.118
.098
.094
Competitor A
.079
.002
.004
.006
.008
Feed (inch/rev)
Number of Passes
Work Material
Hardness
Grade
Cutting Speed
(SFM)
Coolant
H Hardened Steel
35 65HRC
MB8025
330
(195 390)
Dry,Wet
Workpiece : Hardened Steel
(HRC60)
Feed
: .004IPR
APPLICATION EXAMPLE
GY1G0300F020N-GFGS (Grade : MB8025)
Insert
Transmission shaft (AISI 8620 (HRC58 62))
Cutting
Conditions
Workpiece
Cutting Speed (SFM)
420
(IPR)
.004
Feed
(pieces)
Result
Competitors
CBN grade
Fracture
GY achieves longer tool life without fracturing.
B012

Dry Cutting
CBN BREAKER INSERT

FEATURES
BM/BF
BREAKER)
APPLICATION AREA
Depth of Cut (inch)
a Chip breaker geometry designed for excellent chip control

Radial chip breaker ensures optimization of the cutting point and the chip breaker
position.
Enables effective chip discharge even when copy machining and prevents the chips
from wrapping around the holder under nish cutting conditions.
a Long life coated CBN grade
Combination of Coating grade & Breaker, high efciency and long tool life in wide
variety of applications.
BM breaker
Area
BF breaker
Area
Feed (IPR)
DEEP CUTTING DEPTH
y Cutting Performance
Recommend and under

ap=.024 inch
Available in BC8020 grade.
LIGHT CUTTING DEPTH

BF Breaker
Good for chip removal
under light depth and feed
cutting.
Recommend and under
ap=.012 inch
Available in MBC020 grade.
Workpiece : Hardened Steel(60HRC)
Insert
: BM-CNGM432TA
Feed
: .008IPR
Dry Cutting
Flank Wear (inch)
BM Breaker
Good for deep depth
cutting of carburized layer.
Fracture
Conventional
Fracture
Cutting Time (min)
BF breaker
Workpiece : Hardened Steel(55HRC)
: BF-CNGG432-TA4
Insert
Feed
: .008IPR
Dry Cutting
Conventional
MULTI-CORNER TYPE INSERTS

a A single sided, multi-corner type insert has no cutting edges on the 2nd side.
The type of grade is stamped on the 1st side.
Double Sided, multi-corner type insert, ex.
y Double sided, multi-corner type insert
1st side
2nd side
NP-CNGA120408GA4
No. of Cutting Edges
Single Sided, multi-corner type insert, ex.
NP-CNGA120408GA2
No. of Cutting Edges
10-Insert Pack
10-INSERTS PACKS
Two types of packs for Multi-corner type inserts are available.
A single insert pack and a ten insert pack, for easy storage.
TNP-CNGA120404G2
10-Insert Pack Symbol
B013
WIPER INSERT
y What is a Wiper Insert?
a Improving Surface Finish
The wiper insert is designed with a wiper edge that is

situated where the straight edge meets the corner
radius.
Wiper
In comparison to conventional
inserts, the surface nish does not
deteriorate even if the feed rate is
doubled.
Machining at high feed rates
improves machining efciency.
Under the same machining conditions as conventional inserts, but with the feed rate
increased, the surface nish of the workpiece can be improved.
a Improving Efciency
High feed rates not only shorten machining times but also make it possible to combine
roughing and nishing operations.
a Increased Tool Life

When changing to high feed conditions, the time required to cut one component is
decreased, thus more parts can be machined with each insert. In addition, the high
feed rate prevents rubbing, therefore, delaying the progression of wear and increasing
the tool life of the insert.
NP-CNGA432-GAWS2
Wiper Symbol
Workpiece : Hardened steel (HRC60)
Insert : NP-CNGA432-GAWS2
Cutting Speed : 390 SFM
Depth of Cut : .004 inch
Dry Cutting
y Wiper insert + machining at high feed rates

Reduced machining time
Increased production rate
Improved chip control
600
y Wiper insert + machining at conventional feed rates
Surface nish (!inch)
Theoretical nished surface roughness
Eliminating the nishing step

(Combine roughing and nishing into single pass.)
400
without wiper
Reducing cost
Increased productivity
Reduced machine down time
200
with WS wiper
.002
.004
.008
<Real cost reduction!!>
.012
Feed rate (IPR)
Special attention is not necessary when using C-style and W-style inserts
y Restriction for Holders
y No Restriction for Holder

The standard holder can be used as it is.
( The double clamp, high rigidity holder
is recommended.)
Use a holder with an end cutting angle of 93 to

improve wiper efciency. A holder with a cutting
edge angle of 91 can marginally improve wiper
efciency (see the gure
End Cutting Angle
below), however, there is no
93
wiper efciency with other
(Specied)
end cutting angles (60, 90,
107 etc.).
End Cutting
Angle
Non
restriction
95
Cutting Conditions and Performance

High feed, high efcient cutting
High precision nishing
High feed, highly efcient cutting
Cutting speed : 330 SFM Feed : .004 IPR

Depth of cut : .004 inch Dry cutting
Cutting speed : 330 SFM Feed : .012 IPR

Depth of cut : .004 inch Dry cutting
Without Wiper
With Wiper
Without Wiper
With Wiper
Ry=126!inch
Ry=40!inch
Ry=480!inch
Ry=47!inch
Depth of cut (inch)
High precision nishing
B014
Feed (IPR)
SINTERED DIAMOND
PCD GRADE MD220

and ber reinforced plastics.
a Suitable for extremely high speed nishing.
Micro-Structure of MD220
a TURNING
Work Material

Recommended Cutting Speed
Feed (IPR)
Depth of Cut (inch)
(SFM)
Aluminum
3280 (650 4920)
.008
.200
Aluminum Alloy (Si < 16%)
2630 (650 3940)
.008
.200
Aluminum Alloy (Si < 16%)
1970 (650 3280)
.008
.118
Copper Alloy
2300 (650 3940)
.008
.118
Reinforced Plastic
1970 (330 3280)
.016
.079
Glass Fiber Reinforced Plastic
1640 (330 2630)
.010
.079
Carbon
1210 (330 1970)
.012
.079
Ceramics
165 (100 260)
.004
.079
Hard Rubber
1970 (980 2630)
.006
.039
4260 (980 12100)
.016
.008
.020
Wood Inorganic Board

Tungsten Carbide
50 (16 65)
a Suitable for materials such as aluminum alloy, non-ferrous metals,
(Note) Not suitable for steel.
CUTTING PERFORMANCE
Flank Wear (inch)
Workpiece : High Si Aluminum Alloy
Insert : SPG422
vc=655SFM
ap=.059inch
f=.006IPR
Coolant : W.S.O
Machined Length (miles)

Sintered diamond tool wear for high Si aluminum alloy cutting
NEW PETIT CUT PCD INSERTS
FEATURES
The small PCD delivers long tool life. Eliminates the need for regrinding,
making tool management easier and economical.
a PCD with chip breaker Chip breaker formed directly on the PCD portion delivers superior chip control.
a Corner R.002inch inserts are available, making it suitable for the machining of small work corner radii.
a Economical inserts
CUTTING PERFORMANCE
y Without chip breaker
Feed (IPR)
y With chip breaker
.012
.008
NP-TNMM331RF
.004
.002
Workpiece : A5052
Feed
: .004IPR
Depth of Cut : .004IPR

Dry Cutting
.01
.02
.03
Depth of Cut (inch)

Workpiece : Aluminum Alloy
Wet Cutting
.04
B015
Type
Tolerance

Product Name
Rhombic 80 Rhombic 55 Square 90 Triangular 60 Rhombic 35 Trigon 80

Breaker
and
Cross Section
Flat Top
NP-CNGA_o4 NP-DNGA_o4 NP-SNGA_o4 NP-TNGA_o6 NP-VNGA_o4 NP-WNGA_o6
Multi-corner Type
Double Sided
^ B022
Multi-corner Type
Double Sided
With Wiper
Multi-corner Type
Double Sided
With Breaker
Flat Top
G Class
CLASSIFICATION
^ B025
BF
Flat Top
M Class
NEW PETIT CUT
Flat Top
Flat Top
G Class
^ B028
*
^ B030
^ B032
*
^ B026
^ B028
^ B034
^ B032
NP-CNGA_oWS2 NP-DNGA_oWS2JR/L
NP-WNGA_oWS3
*
^ B026
^ B034
BF-CNGM_o2 BF-DNGM_o2
^ B026
BM-CNGM_o2 BM-DNGM_o2
^ B023
Flat Top
^ B025, B026
NP-VNMA_o2
^ B023
BM
NP-CNMA_o2 NP-DNMA_o2 NP-SNMA_o2
^ B023
BF
^ B025
^ B023
Multi-corner Type
Single Sided
With Breaker
^ B034
NP-CNGA_o2 NP-DNGA_o2 NP-SNGA_o2 NP-TNGA_o3 NP-VNGA_o2 NP-WNGA_o3
^ B022, B023
Multi-corner Type
Single Sided
With Breaker
^ B032
^ B022
Multi-corner Type
Single Sided
Multi-corner Type
Single Sided
With Wiper
^ B030
BF-CNGG_o4 BF-DNGG_o4
^ B022
Multi-corner Type
Single Sided
^ B028
NP-CNGA_oWS4
BM-TNGM_o3
^ B026
^ B031
NP-CNGA_o NP-DNGA_o NP-SNGA_o NP-TNGA_o NP-VNGA_o NP-WNGA_o
One-corner Type
Single Sided
^ B024
B016
^ B027
^ B028
^ B031
^ B033
: These items can be chosen as "10 inserts in one case" package. (The standard package is "1 insert in one case".)
^ B034

Breaker
and
Cross Section
One-corner Type
Single Sided
One-corner Type
Single Sided
With Breaker
M Class
NEW PETIT CUT
Flat Top
NP-CNMA_o NP-DNMA_o NP-SNMA_o NP-TNMA_o NP-VNMA_o
^ B024
R/L F
G Class
M Class
STANDARD
One-corner Type
Single Sided
Flat Top
Flat Top
^ B028
^ B031
^ B033
NP-CNMM_R/LF NP-DNMM_R/LF NP-SNMM_R/LF NP-TNMM_R/LF NP-VNMM_R/LF
^ B054
One-corner Type
Single Sided
^ B027
Type
Tolerance
Product Name
^ B054
^ B055
^ B055
^ B056
DNGA
SNGA
TNGA
VNGA
^ B027, B054
^ B028, B055
^ B031, B055
^ B033, B056
CNMA
^ B024, B054
Type
Tolerance
Product Name

Breaker
and
Cross Section
Flat Top
NP-VBGW_o2
^ B047
One-corner Type
G Class
NEW PETIT CUT
Multi-corner Type
Flat Top
NP-VBGW_o
^ B047
RF
NP-VBGT_RF
One-corner Type
With Breaker
^ B063
B017
Type
Tolerance

Product Name

Breaker
and
Cross Section
Flat Top
Multi-corner Type
NP-CCGW/B_o2 NP-DCGW_o2
Multi-corner Type
With Wiper
Multi-corner Type
With Breaker
Flat Top
NP-TCGW_o3 NP-VCGW_o2 NP-WCGW_o3
*
^ B038
G Class
CLASSIFICATION
^ B042
^ B044
^ B048
^ B049
NP-CCGW_oWS2
^ B039
BF
BF-CCGT_o2 BF-DCGT_o2
^ B039
Flat Top
^ B042
NP-CCGW/B_o NP-DCGW_o
NP-TCGW_o NP-VCGW_o
One-corner Type
Flat Top
^ B043
^ B044
^ B048
One-corner Type
^ B039
Flat Top
NP-CCMW_o NP-DCMW_o
NP-WCMW_o
One-corner Type
M Class
NEW PETIT CUT
^ B039, B040
NP-CCMB_o
^ B040
Flat Top
^ B043
^ B049
NP-CCMW
One-corner Type
^ B058
Breaker
One-corner Type
With Breaker
NP-CCMH
B018
One-corner Type
^ B063
M Class
STANDARD
One-corner Type
With Breaker
NP-VCGT_RF
RF
R/L F
G Class
One-corner Type
With Breaker
G Class
^ B058
Flat Top
NP-DCMT_R/LF
^ B059
TCGW
^ B060
One-corner Type

Breaker
and
Cross Section
Flat Top
CCMW
DCMW
TCMW
WCMW
^ B040, B058
^ B043, B059
^ B044, B060
^ B064
Type
Tolerance
Product Name

Breaker
and
Cross Section
Flat Top
NP-CPGB_o2
Type
M Class Tolerance
STANDARD Product Name
NP-TPGB_o3
G Class
Multi-corner Type
^B041
^ B045
NP-TPGX_o3
Flat Top
Multi-corner Type
One-corner Type
G Class
NEW PETIT CUT
One-corner Type
M Class
^ B045
Flat Top
NP-TPMB_o
^ B041
^ B045
NP-TPGX_o
Flat Top
^ B045
Breaker
One-corner Type
With Breaker
NP-CPMB_o
NP-CPMH
One-corner Type
With Breaker
M Class
^ B058
NP-TPMH_R/LF
R/L F
^ B061
NP-TPMX_R/LF
R/L F
One-corner Type
With Breaker
^ B061
Breaker
One-corner Type
With Breaker
CPGT
WPGT
One-corner Type
One-corner Type
With Breaker
G Class
STANDARD
^ B058
Flat Top
^ B064
SPGX
^ B059
R/L F
TPGX
^ B046, B062
TPGT/V_R/LF
^ B061, B062
B019
Tolerance
Type
VDGX_R/LF
Rhombic 55 Triangular 60
Breaker
and
Cross Section
TEGX_R/L
R/L
One-corner Type
With Breaker
^ B066
^ B065
One-corner Type
With Breaker
G Class
R/L
Product Name
Rhombic 35
Breaker
and
Cross Section
FOR ALUMINUM
One-corner Type
With Breaker
Tolerance
Type
G Class
Product Name
FOR ALUMINUM
CLASSIFICATION
R/L F
DEGX_R/LF
^ B065
Flat Top
TEGX
One-corner Type
^ B065
B020
Rhombic 80 Rhombic 55 Square 90 Triangular 60

Breaker
and
Cross Section
Flat Top
Round
CNG
DNG
SNG
TNG
RNG
^ B035
^ B035
^ B036, B057
^ B037
^ B036
STANDARD
G Class
Product
Name
Tolerance
STANDARD
G Class
Product
Name
Tolerance

Triangular 60
Breaker
and
Cross Section
Flat Top
TBG
^ B052
Flat Top
SPG
Tool Holder
Type
Tolerance
Square 90 Triangular 60
Breaker
and
Cross Section
SPECIAL PURPOSE INSERTS
TPG
Inserts
RTG_A
TL Type
^ B051, B067
G Class
STANDARD
G Class
Product
Name
Tolerance
^ B053, B067
^ B050
RBG

^ B050
B021
80
CN
TYPE INSERTS
WITH HOLE
Work
Material
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
Order Number
(ISO) Number
Corner
Radius
(inch)
NEW PETIT CUT
WITH
HOLE
NEW PETIT CUT
NEW PETIT CUT
(With breaker)
NEW PETIT CUT
NP-CNGA431-GA4
432-GA4
433-GA4
431-GN4
432-GN4
433-GN4
431-FS4
432-FS4
433-FS4
431-TA4
432-TA4
433-TA4
NP-CNGA431-GAWS4
432-GAWS4
433-GAWS4
NP-CNGA120404GA4
120408GA4
120412GA4
120404GN4
120408GN4
120412GN4
120404FS4
120408FS4
120412FS4
120404TA4
120408TA4
120412TA4
NP-CNGA120404GAWS4
120408GAWS4
120412GAWS4
.016
a s
.031
a s
BF-CNGG431-TA4
432-TA4
433-TA4
BF-CNGG120404TA4
120408TA4
120412TA4
.016
.031
.047
NP-CNGA431-GA2
432-GA2
433-GA2
431-GS2
432-GS2
433-GS2
431-GN2
432-GN2
433-GN2
431-FS2
432-FS2
433-FS2
431-TA2
432-TA2
433-TA2
431-TS2
432-TS2
433-TS2
NP-CNGA120404GA2
120408GA2
120412GA2
120404GS2
120408GS2
120412GS2
120404GN2
120408GN2
120412GN2
120404FS2
120408FS2
120412FS2
120404TA2
120408TA2
120412TA2
120404TS2
120408TS2
120412TS2
.016
a s
.031
a s

a
r
Coated
CBN
CBN
.047
a s
.016
.031
.047
.016
.031
.047
.016
s s
.031
s s
.047
s s
.016
.031
.047
Applicable
Holder Page
Sintered Alloy
NEG
B022
H
K
S

MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
NP-CNGA 4 3 1 GA4
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
a s
.047
.016
a a
.031
a a
.047
a a
.016
.031
.047
.016
.031
.047
.016
a s
.031
a s
.047
a s
.016
.031
.047
C006
009
E021
E024
H006
008
Work
Material
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
CBN
Cast Iron
(ISO) Number
Order Number
(inch)
NEW PETIT CUT
NEW PETIT CUT
NEW PETIT CUT
NEW PETIT CUT
NEW PETIT CUT

(With Wiper)
NEW PETIT CUT
(With breaker)
NEW PETIT CUT
NP-CNGA431-G2
432-G2
433-G2
431-T2
432-T2
433-T2
1 TNP-CNGA432-GS2
1
433-GS2
1
431-G2
1
432-G2
1
433-G2
1
431-T2
1
432-T2
1
433-T2
NP-CNMA431-G2
432-G2
433-G2
431-T2
432-T2
433-T2
1 TNP-CNMA431-G2
1
432-G2
1
433-G2
1
432-T2
1
433-T2
2 NP-CNGA431-GAWS2
2
432-GAWS2
2
433-GAWS2
2
431-GSWS2
2
432-GSWS2
2
433-GSWS2
BF-CNGM431-TA2
432-TA2
433-TA2
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
BM-CNGM432-TA2
433-TA2
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
NP-CNGA120404G2
120408G2
120412G2
120404T2
120408T2
120412T2
TNP-CNGA120408GS2
120412GS2
120404G2
120408G2
120412G2
120404T2
120408T2
120412T2
NP-CNMA120404G2
120408G2
120412G2
120404T2
120408T2
120412T2
TNP-CNMA120404G2
120408G2
120412G2
120408T2
120412T2
NP-CNGA120404GAWS2
120408GAWS2
120412GAWS2
120404GSWS2
120408GSWS2
120412GSWS2
BF-CNGM120404TA2
120408TA2
120412TA2
.016
.031
.047
.016
.031
BM-CNGM120408TA2
120412TA2
.031
.047
.047
C006
009
E021
E024
H006
008
.031
.047
C006
009
E021
E024
H006
008
.031
.047
.016
.031
.047
.016
a a
.031
a a
.047
a a
.016
.031
.047
.016
a a
.031
a a
.047
a r
.031
.047
.016
.031
.047
s
.031
.047
.016
.031
.047
NEG
WITH
HOLE
.016
.016
Applicable
Holder Page
Sintered Alloy
H
K
S
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
(With breaker)
order number is for "10 inserts in one case" package.
*12 This
Please refer to page B014 before using the wiper insert.
*
IDENTIFICATION
B002
HONING
B011
B023
80
CN
TYPE INSERTS
WITH HOLE
Work
Material
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
Order Number
(ISO) Number
Corner
Radius
(inch)
NEW PETIT CUT
WITH
HOLE
NEW PETIT CUT
NP-CNGA431GA
432GA
433GA
431GN
432GN
433GN
431TA
432TA
433TA
NP-CNMA431GS
432GS
433GS
431G
432G
433G
431F
432F
433F
431T
432T
433T
CNMA431
432
433
NP-CNGA120404GA
120408GA
120412GA
120404GN
120408GN
120412GN
120404TA
120408TA
120412TA
NP-CNMA120404GS
120408GS
120412GS
120404G
120408G
120412G
120404F
120408F
120412F
120404T
120408T
120412T
CNMA120404
120408
120412

a
r
Coated
CBN
CBN
.016
.031
.047
.016
.031
.047
.016
.031
.047
Applicable
Holder Page
Sintered Alloy
NEG
B024
H
K
S

MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
NP-CNGA 4 3 1 GA
C006
009
E021
E024
H006
008
.016
a a
.031
a a
a a
.047
.016
a a
.031
a a
a a
a a
a a
.047
.016
a r
.031
a r
.047
a r
.016
r s a
.031
r s a
.047
r s a
C006
009
E021
E024
H006
008
.016
a a
.031
s a s
a a
.047
a a
C006
009
E021
E024
H006
008
DN
Work
Material
H
K
S
NP-DNGA 4 3 1 GA4
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Order Number
(ISO) Number
(inch)
NEW PETIT CUT
NEW PETIT CUT
NP-DNGA431-GA4
432-GA4
433-GA4
431-GN4
432-GN4
433-GN4
431-FS4
432-FS4
433-FS4
431-TA4
432-TA4
433-TA4
BF-DNGG431-TA4
432-TA4
433-TA4
(With breaker)
NEW PETIT CUT NP-DNGA332-GA2
431-GA2
432-GA2
433-GA2
332-GS2
431-GS2
432-GS2
433-GS2
332-GN2
431-GN2
432-GN2
433-GN2
431-FS2
432-FS2
433-FS2
332-TA2
431-TA2
432-TA2
433-TA2
431-TS2
432-TS2
433-TS2
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
NP-DNGA150404GA4
150408GA4
150412GA4
150404GN4
150408GN4
150412GN4
150404FS4
150408FS4
150412FS4
150404TA4
150408TA4
150412TA4
BF-DNGG150404TA4
150408TA4
150412TA4
.016
a s
.031
a s
.047
a s
.016
.031
.047
NP-DNGA110408GA2
150404GA2
150408GA2
150412GA2
110408GS2
150404GS2
150408GS2
150412GS2
110408GN2
150404GN2
150408GN2
150412GN2
150404FS2
150408FS2
150412FS2
110408TA2
150404TA2
150408TA2
150412TA2
150404TS2
150408TS2
150412TS2
.016
.031
.047
.016
s s
.031
s s
.047
s s
.016
.031
.047
.031
.016
a s
.031
a s
NEG
C010
012
E024
H009
011
WITH
HOLE
C010
012
E024
H009
011
a s
.047
.031
.016
a a
.031
a a
.047
a a
.031
Applicable
Holder Page
Sintered Alloy
CBN
55
TYPE INSERTS
WITH HOLE
.016
.031
.047
.016
.031
.047
.031
.016
a s
.031
a s
.047
a s
.016
.031
.047
C010
012
E024
H009
011
IDENTIFICATION
B002
HONING
B011
B025
DN
55
H
K
S
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
Order Number
(ISO) Number
Corner
Radius
(inch)
NEW PETIT CUT NP-DNGA431-G2
WITH
HOLE
NEW PETIT CUT
NEW PETIT CUT
NEW PETIT CUT
NEW PETIT CUT

(With Wiper)
NEW PETIT CUT
432-G2
433-G2
431-T2
432-T2
433-T2
1 TNP-DNGA431-GS2
1
432-GS2
1
433-GS2
1
431-G2
1
432-G2
1
433-G2
1
431-T2
1
432-T2
1
433-T2
NP-DNMA431-G2
432-G2
433-G2
431-F2
432-T2
1 TNP-DNMA431-G2
1
432-G2
1
433-G2
*
*
*
*
*
*
*
*
*
*
*
*
*22 NP-DNGA431-GAWS2JR
431-GAWS2JL
*2
432-GAWS2JR
*2
432-GAWS2JL
*2
431-GSWS2JR
*2
431-GSWS2JL
*2
432-GSWS2JR
*2
432-GSWS2JL
* BF-DNGM431-TA2
432-TA2
433-TA2
(With breaker)
NEW PETIT CUT
BM-DNGM432-TA2
433-TA2
.016
.031
.047
.016
.031
NP-DNGA150404GAWS2JR
150404GAWS2JL
150408GAWS2JR
150408GAWS2JL
150404GSWS2JR
150404GSWS2JL
150408GSWS2JR
150408GSWS2JL
BF-DNGM150404TA2
150408TA2
150412TA2
.016
.016
.031
.031
BM-DNGM150408TA2
150412TA2

*12 This
Please refer to page B014 before using the wiper insert.
* a : Inventory maintained. s : Inventory maintained in Japan.
CBN
NP-DNGA150404G2
150408G2
150412G2
150404T2
150408T2
150412T2
TNP-DNGA150404GS2
150408GS2
150412GS2
150404G2
150408G2
150412G2
150404T2
150408T2
150412T2
NP-DNMA150404G2
150408G2
150412G2
150404F2
150408T2
TNP-DNMA150404G2
150408G2
150412G2
(With breaker)
Coated
CBN
.047
Applicable
Holder Page
Sintered Alloy
NEG
B026

MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
Work
Material
NP-DNGA 4 3 1 G2
TYPE INSERTS
WITH HOLE
C010
012
E024
H009
011
.016
.031
.047
C010
012
E024
H009
011
.016
.031
.047
.016
.031
.047
.016
a a
.031
a a
a a
.047
.016
.031
C010
012
E024
H009
011
.016
a a
.031
a a
.047
a a
.016
.016
.031
.031
.016
.031
.047
C010
012
E024
H009
011
C010
E024
H009
H011
C010
012
E024
H009
011
.031
.047
C010
012
E024
H009
011
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
CBN
Cast Iron
Order Number
(ISO) Number
(inch)
NEW PETIT CUT
NEW PETIT CUT
NP-DNGA431GA
432GA
433GA
431GN
432GN
433GN
431TA
432TA
433TA
NP-DNMA431GS
432GS
332G
431G
432G
433G
431F
432F
433F
431T
432T
433T
DNGA431
432
433
NP-DNGA150404GA
150408GA
150412GA
150404GN
150408GN
150412GN
150404TA
150408TA
150412TA
NP-DNMA150404GS
150408GS
110408G
150404G
150408G
150412G
150404F
150408F
150412F
150404T
150408T
150412T
DNGA150404
150408
150412
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
.016
.031
.047
.016
.031
.047
.016
.031
.047
Applicable
Holder Page
Sintered Alloy
C010
012
E024
H009
011
.016
Work
Material
H
K
S
NEG
WITH
HOLE
a a
.031
.031
a a
.016
a a
.031
a a
a a
.047
a a
a a
.016
a r
.031
a r
.047
a r
.016
r s a
.031
r s a
.047
C010
012
E024
H009
011
.016
r r
.031
a s
r r
.047
r r
C010
012
E024
H009
011
IDENTIFICATION
B002
HONING
B011
B027
SN
90
TYPE INSERTS
WITH HOLE
H
K
S
Work
Material

Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
(ISO) Number
Order Number
Corner
Radius
(inch)
NEW PETIT CUT
NEG
NP-SNGA431-GA4
432-GA4
433-GA4
NP-SNGA120404GA4
120408GA4
120412GA4
.016
NP-SNGA431-GA2
432-GA2
433-GA2
431-GS2
432-GS2
433-GS2
431-FS2
432-FS2
433-FS2
431-TS2
432-TS2
433-TS2
431-G2
432-G2
433-G2
431-T2
432-T2
433-T2
1 TNP-SNGA431-G2
1
432-G2
1
433-G2
1
431-T2
1
432-T2
1
433-T2
NP-SNMA433-G2
NP-SNGA120404GA2
120408GA2
120412GA2
120404GS2
120408GS2
120412GS2
120404FS2
120408FS2
120412FS2
120404TS2
120408TS2
120412TS2
120404G2
120408G2
120412G2
120404T2
120408T2
120412T2
TNP-SNGA120404G2
120408G2
120412G2
120404T2
120408T2
120412T2
NP-SNMA120412G2
Coated
CBN
CBN
.031
.047
.016
.031
.047
C014
017
E022
E025
WITH
HOLE
NEW PETIT CUT
NEW PETIT CUT
NEW PETIT CUT
*
*
*
*
*
*
Applicable
Holder Page
Sintered Alloy
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
NP-SNGA 4 3 1 GA4
.016
.031
a a
.047
a a
.016
.031
.047
.016
.031
.047
C014
017
E022
E025
.016
.031
.047
.016
.031
.047
.016
.031
.047
.016
.031
.047
.047
C014
017
E022
E025
C014
017
E022
E025
NEW PETIT CUT
NP-SNGA431GA
432GA
433GA
NP-SNGA120404GA
120408GA
120412GA
*1 This order number is for "10 inserts in one case" package.

a
B028
.016
.031
.047
C014
017
E022
E025
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
CBN
Cast Iron
Order Number
(ISO) Number
(inch)
NEW PETIT CUT
NP-SNMA431GS
432GS
431G
432G
433G
431F
432F
433F
431T
432T
433T
SNGA431
432
433
NP-SNMA120404GS
120408GS
120404G
120408G
120412G
120404F
120408F
120412F
120404T
120408T
120412T
SNGA120404
120408
120412
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
.016
a a
.031
.016
Applicable
Holder Page
Sintered Alloy
a a
s s
.031
a s
.047
.016
a r
.031
a r
.047
s r
C014
017
E022
E025
.016
r s a
.031
r s a
.047
r s s
.016
r r
.031
a a
.047
a a
Work
Material
H
K
S
NEG
WITH
HOLE
C014
017
E022
E025
IDENTIFICATION
B002
HONING
B011
B029
60
TN
TYPE INSERTS
WITH HOLE
Work
Material
H
K
S
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
Order Number
(ISO) Number
Corner
Radius
(inch)
NEW PETIT CUT
WITH
HOLE
NEW PETIT CUT
NP-TNGA331-GA6
332-GA6
333-GA6
331-GN6
332-GN6
333-GN6
331-FS6
332-FS6
333-FS6
331-TA6
332-TA6
333-TA6
NP-TNGA330.5-GA3
331-GA3
332-GA3
333-GA3
331-GS3
332-GS3
333-GS3
330.5-GN3
331-GN3
332-GN3
333-GN3
331-FS3
332-FS3
333-FS3
331-TA3
332-TA3
333-TA3
331-TS3
332-TS3
333-TS3
331-G3
332-G3
333-G3
331-T3
332-T3
333-T3
NP-TNGA160404GA6
160408GA6
160412GA6
160404GN6
160408GN6
160412GN6
160404FS6
160408FS6
160412FS6
160404TA6
160408TA6
160412TA6
NP-TNGA160402GA3
160404GA3
160408GA3
160412GA3
160404GS3
160408GS3
160412GS3
160402GN3
160404GN3
160408GN3
160412GN3
160404FS3
160408FS3
160412FS3
160404TA3
160408TA3
160412TA3
160404TS3
160408TS3
160412TS3
160404G3
160408G3
160412G3
160404T3
160408T3
160412T3

a
Coated
CBN
CBN
.016
a s
.031
a s
.047
a s
.016
.031
.047
.016
.031
.047
.016
s s
.031
s s
.047
s s
.008
.016
a s
.031
a s
Applicable
Holder Page
Sintered Alloy
NEG
B030

MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
NP-TNGA 3 3 1 GA6
C018
023
E022
E025
a s
.047
.016
.031
a a
.047
a a
.008
.016
.031
.047
.016
.031
.047
.016
a s
.031
a s
.047
a s
.016
.031
.047
.016
.031
.047
.016
.031
.047
C018
023
E022
E025
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
CBN
Cast Iron
(ISO) Number
Order Number
(inch)
NEW PETIT CUT
NEW PETIT CUT
*11 TNP-TNGA331-G3
332-G3
*1
333-G3
*1
331-T3
*1
332-T3
*1
333-T3
*BM-TNGM332-TA3
333-TA3
(With breaker)
NEW PETIT CUT NP-TNGA331GA
NEW PETIT CUT
332GA
333GA
331GN
332GN
333GN
331TA
332TA
333TA
NP-TNMA331GS
332GS
333GS
331G
332G
333G
331F
332F
333F
331T
332T
333T
TNGA331
332
431
432
433
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
TNP-TNGA160404G3
160408G3
160412G3
160404T3
160408T3
160412T3
BM-TNGM160408TA3
160412TA3
.016
.031
.047
.016
.031
NP-TNGA160404GA
160408GA
160412GA
160404GN
160408GN
160412GN
160404TA
160408TA
160412TA
NP-TNMA160404GS
160408GS
160412GS
160404G
160408G
160412G
160404F
160408F
160412F
160404T
160408T
160412T
TNGA160404
160408
220404
220408
220412
.016
.031
.047
.016
.031
.047
.016
.031
.047
.047
Applicable
Holder Page
Sintered Alloy
C018
023
E022
E025
.031
.047
Work
Material
H
K
S
NEG
WITH
HOLE
C018
023
E022
E025
C018
023
E022
E025
.016
a a
.031
a a
.047
a a
.016
a s
.031
a s
.047
a s
.016
a r
.031
a r
.047
a r
C018
023
E022
E025
.016
r a a
.031
r a a
r a a
.047
.016
.031
a a
a a
.016
a r
.031
a r
.047
a r
C018
023
E022
E025
1 This order number is for "10 inserts in one case" package.
IDENTIFICATION
B002
HONING
B011
B031
35
VN
TYPE INSERTS
WITH HOLE
H
K
S
Work
Material
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
(ISO) Number
Order Number
Corner
Radius
(inch)
NEW PETIT CUT
WITH
HOLE
NEW PETIT CUT
NEW PETIT CUT
NEW PETIT CUT
NEW PETIT CUT
NP-VNGA331-GA4
332-GA4
333-GA4
331-FS4
332-FS4
333-FS4
331-TA4
332-TA4
333-TA4
NP-VNGA330.5-GA2
331-GA2
332-GA2
331-GS2
332-GS2
330.5-GN2
331-FS2
332-FS2
331-TA2
332-TA2
331-TS2
332-TS2
331-G2
332-G2
331-T2
332-T2
1 TNP-VNGA331-GS2
1
332-GS2
1
331-G2
1
332-G2
1
331-T2
1
332-T2
NP-VNMA331-G2
332-G2
331-F2
332-F2
331-T2
1 TNP-VNMA331-F2
1
332-F2
1
331-G2
1
332-G2
*
*
*
*
*
*
*
*
*
*
NP-VNGA160404GA4
160408GA4
160412GA4
160404FS4
160408FS4
160412FS4
160404TA4
160408TA4
160412TA4
NP-VNGA160402GA2
160404GA2
160408GA2
160404GS2
160408GS2
160402GN2
160404FS2
160408FS2
160404TA2
160408TA2
160404TS2
160408TS2
160404G2
160408G2
160404T2
160408T2
TNP-VNGA160404GS2
160408GS2
160404G2
160408G2
160404T2
160408T2
NP-VNMA160404G2
160408G2
160404F2
160408F2
160404T2
TNP-VNMA160404F2
160408F2
160404G2
160408G2
*1 This order number is for "10 inserts in one case" package.

a
r
Coated
CBN
CBN
.016
a s
.031
a s
.047
.016
.031
.047
.016
.031
.047
Applicable
Holder Page
Sintered Alloy
NEG
B032

MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
NP-VNGA 3 3 1 GA4
C024
026
E023
E026
.008
.016
a s
a s
.031
.016
.031
.008
.016
.031
.016
.031
.016
C024
026
E023
E026
.031
.016
.031
.016
.031
.016
.031
C024
026
E023
E026
.016
.031
.016
.031
.016
a a
.031
a a
.016
.031
.016
C024
026
E023
E026
.016
.031
.016
a a
.031
a a
C024
026
E023
E026
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
CBN
Cast Iron
Order Number
(ISO) Number
(inch)
NEW PETIT CUT
NP-VNGA331GA
332GA
NP-VNGA160404GA
160408GA
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
.016
.031
Applicable
Holder Page
Sintered Alloy
C024
026
E023
E026
Work
Material
H
K
S
NEG
NEW PETIT CUT
NP-VNMA331GS
332GS
331G
332G
331F
332F
331T
332T
VNGA331
332
NP-VNMA160404GS
160408GS
160404G
160408G
160404F
160408F
160404T
160408T
VNGA160404
160408
.016
a a
.031
a a
.016
a a
.031
a a
a a
.016
a r
.031
a r
.016
r s a
.031
r s a
.016
r r
.031
a s
r r
WITH
HOLE
C024
026
E023
E026
a
a
C024
026
E023
E026
IDENTIFICATION
B002
HONING
B011
B033
80
WN
TYPE INSERTS
WITH HOLE
Work
Material
H
K
S

Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
(ISO) Number
Order Number
Corner
Radius
(inch)
NEW PETIT CUT
NP-WNGA432-GA6
NP-WNGA080408GA6
Coated
CBN
CBN
.031
Applicable
Holder Page
Sintered Alloy
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
NP-WNGA 4 3 2 GA6
s s
C027
E023
E026
E027
NEG
WITH
HOLE
NEW PETIT CUT
NEW PETIT CUT

(With Wiper)
NEW PETIT CUT
NP-WNGA432-GA3
432-FS3
432-TS3
*11 NP-WNGA432-GAWS3
432-GSWS3
*
NP-WNGA432GA
NP-WNGA080408GA3
080408FS3
080408TS3
.031
a s
.031
.031
NP-WNGA080408GAWS3
080408GSWS3
.031
NP-WNGA080408GA
.031
.031
a
s
C027
E023
E026
E027
C027
E023
E026
E027
C027
E023
E026
E027
*1 Please refer to page B014 before using the wiper insert.
B034

CN
Work
Material
H
K
S

Stable Cutting
General Cutting
CBN
Unstable Cutting
Hardened Materials
Cast Iron
(ISO) Number
Order Number
(inch)
CNG431
432
433
CNGN120404
120408
120412
Coated
CBN
CBN
Solid
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
MBS140
Shape
Corner
Radius
.016
.031
.047
Applicable
Holder Page
Sintered Alloy
C007
009
E024
80
CNG 4 3 1
TYPE INSERTS
WITHOUT HOLE
NEG
WITHOUT
HOLE
55
DN
Work
Material
H
K
S
DNG 3 2 2
TYPE INSERTS
WITHOUT HOLE

Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Order Number
(ISO) Number
(inch)
DNG322
323
DNGN110308
110312
Coated
CBN
CBN
Solid
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
MBS140
Shape
Corner
Radius
.031
.047
Applicable
Holder Page
Sintered Alloy
IDENTIFICATION
B002
HONING
B011
B035
RN
H
K
S
Size Thickness
*Please refer to page B002.

Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
(ISO) Number
Order Number
Corner
Radius
(inch)
RNG32
42
43
NEG
RNGN090300
120300
120400
Coated
CBN
Solid
CBN
CBN
Applicable
Holder Page
Sintered Alloy
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN
Work
Material
RNG 3 2
TYPE INSERTS
WITHOUT HOLE
C013
WITHOUT
HOLE
SN
90
Work
Material
H
K
S
SNG 3 2 2
TYPE INSERTS
WITHOUT HOLE

Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Order Number
(ISO) Number
(inch)
SNG322
323
324
432
433
434
SNG321
322
431
432
433
B036
SNGN090308
090312
090316
120408
120412
120416
SNGN090304
090308
120404
120408
120412

a
r
Coated
CBN
CBN
Solid
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
MBS140
Shape
Corner
Radius
.031
.047
.063
.031
.047
Applicable
Holder Page
Sintered Alloy
C014
017
E025
.063
.016
r r
.031
r r
.016
r r
.031
a r
.047
a r
C014
017
E025
TN
Work
Material
H
K
S

Stable Cutting
General Cutting
CBN
Unstable Cutting
Hardened Materials
Cast Iron
Order Number
(ISO) Number
(inch)
TNG332
333
334
TNG331
332
TNGN160408
160412
160416
TNGN160404
160408
Coated
CBN
Solid
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
MBS140
Shape
Corner
Radius
.031
.047
.063
.016
a r
.031
a r
IDENTIFICATION
Applicable
Holder Page
Sintered Alloy
C019
021
C023
E025
60
TNG 3 3 2
TYPE INSERTS
WITHOUT HOLE
NEG
WITHOUT
HOLE
C019
021
C023
E025
B002
B037
80
CC
TYPE INSERTS
WITH HOLE
Work
Material
H
K
S

Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
Order Number
(ISO) Number
Corner
Radius
(inch)
Coated
CBN
CBN
NEW PETIT CUT
NP-CCGB21.51-GA2
NP-CCGB060204GA2
.016
NEW PETIT CUT
NP-CCGW21.50.5-GA2
21.51-GA2
21.52-GA2
32.50.5-GA2
32.51-GA2
32.52-GA2
21.50.5-GS2
21.51-GS2
21.52-GS2
32.51-GS2
32.52-GS2
32.50.5-GN2
32.51-GN2
32.52-GN2
21.50.5-FA2
21.51-FA2
21.52-FA2
32.51-FA2
32.52-FA2
21.50.5-FS2
21.51-FS2
21.52-FS2
32.50.5-FS2
32.51-FS2
32.52-FS2
21.50.5-TS2
21.51-TS2
21.52-TS2
32.50.5-TS2
32.51-TS2
32.52-TS2
32.51-G2
32.52-G2
32.52-T2
NP-CCGW060202GA2
060204GA2
060208GA2
09T302GA2
09T304GA2
09T308GA2
060202GS2
060204GS2
060208GS2
09T304GS2
09T308GS2
09T302GN2
09T304GN2
09T308GN2
060202FA2
060204FA2
060208FA2
09T304FA2
09T308FA2
060202FS2
060204FS2
060208FS2
09T302FS2
09T304FS2
09T308FS2
060202TS2
060204TS2
060208TS2
09T302TS2
09T304TS2
09T308TS2
09T304G2
09T308G2
09T308T2
.008
a s
.016
a s
.031
.008
a s
.016
a s
.031
a s
C030
D008
D012
E006
E012
E013
POSI
7
WITH
HOLE
B038

a
r
.008
.016
a a
a a
.031
a a
.016
.031
a a
a a
.008
.016
.031
.008
a a
.016
a a
.031
a a
.016
a a
.031
a a
C030
D008
D012
E006
E012
E013
.008
.016
.008
.016
.031
.031
.008
.016
.031
.008
.016
.031
.016
.031
a a
.031
Applicable
Holder Page
Sintered Alloy
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
NP-CCGB 2 1.5 1 GA2
r
r
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
CBN
Cast Iron
(ISO) Number
Order Number
(inch)
NEW PETIT CUT
NEW PETIT CUT

(With Wiper)
*11 TNP-CCGW32.52-GS2
32.51-G2
*1
32.52-G2
*
.031
a
a
.031
a a
.031
BF-CCGT32.51-TA2
32.52-TA2
BF-CCGT09T304TA2
09T308TA2
.016
.031
NEW PETIT CUT
NP-CCMB21.51G
NP-CCMB060204G
.016
NEW PETIT CUT
NP-CCGW21.50.5GA
21.51GA
21.52GA
32.50.5GA
32.51GA
32.52GA
32.50.5GS
32.51GS
32.50.5GN
32.51GN
32.52GN
21.50.5G
21.51G
21.52G
32.50.5G
32.51G
32.52G
21.50.5F
21.51F
32.50.5F
32.51F
32.52F
NP-CCGW060202GA
060204GA
060208GA
09T302GA
09T304GA
09T308GA
09T302GS
09T304GS
09T302GN
09T304GN
09T308GN
060202G
060204G
060208G
09T302G
09T304G
09T308G
060202F
060204F
09T302F
09T304F
09T308F
.008
.016
.031
.008
.016
.031
32.52-GSWS2
CBN
.016
NP-CCGW09T308GAWS2
09T308GSWS2
NEW PETIT CUT
*2 NP-CCGW32.52-GAWS2
TNP-CCGW09T308GS2
09T304G2
09T308G2
Coated
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
.031
C030
D008
D012
E006
E012
E013
Applicable
Holder Page
Sintered Alloy
C030
D008
D012
E006
E012
E013
Work
Material
H
K
S
POSI
7
WITH
HOLE
C030
D008
D012
E006
E012
E013
a
.008
C030
D008
D012
E006
E012
E013
a a
.016
a a
.008
.016
.031
C030
D008
D012
E006
E012
E013
.008
a a
.016
a a
.031
.008
a a
.016
a a
a a
.031
.008
.016
.008
.016
a r
.031

*12 This
* Please refer to page B014 before using the wiper insert.
IDENTIFICATION
B002
HONING
B011
B039
80
CC
TYPE INSERTS
WITH HOLE
Work
Material
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
Order Number
(ISO) Number
Corner
Radius
(inch)
NEW PETIT CUT
WITH
HOLE
NEW PETIT CUT
CBN
NP-CCGW21.50.5T
21.51T
32.50.5T
32.51T
32.52T
NP-CCMW03S102F
03S104F
04T002F
04T004F
NP-CCGW060202T
060204T
09T302T
09T304T
09T308T
NP-CCMW03S102F
03S104F
04T002F
04T004F
.008
.016
.008
CCMW21.50.5
21.51
32.50.5
32.51
32.52
431
432
433
CCMW060202
060204
09T302
09T304
09T308
120404
120408
120412
.008
r r
.016
r r
.008
r r
.016
a a
r r
.031
a a
r r
.016
r r
.031
r r
.047
r r

a
r
Coated
CBN
.016
.031
.008
.016
.008
.016
Applicable
Holder Page
Sintered Alloy
POSI
7
B040
H
K
S

MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
NP-CCGW 2 1.5 0.5 T
C030
D008
D012
E006
E012
E013
E012
E013
C030
D008
D012
E006
E012
E013
CP
Work
Material
H
K
S
NP-CPGB 2.5 1.5 1 GA2

Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Order Number
(ISO) Number
(inch)
NEW PETIT CUT
NEW PETIT CUT
NP-CPGB2.51.51-GA2
2.51.52-GA2
321-GA2
322-GA2
2.51.50.5-FS2
2.51.51-FS2
2.51.52-FS2
320.5-FS2
321-FS2
322-FS2
NP-CPMB2.51.51G
321G
NP-CPGB080204GA2
080208GA2
090304GA2
090308GA2
080202FS2
080204FS2
080208FS2
090302FS2
090304FS2
090308FS2
NP-CPMB080204G
090304G
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
.016
s s
.031
s s
.016
.031
POSI
11
.008
.016
.031
Applicable
Holder Page
Sintered Alloy
CBN
80
TYPE INSERTS
WITH HOLE
WITH
HOLE
E006
.008
.016
.031
.016
.016
E006
IDENTIFICATION
B002
HONING
B011
B041
55
DC
TYPE INSERTS
WITH HOLE
H
K
S
Work
Material
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
Order Number
(ISO) Number
Corner
Radius
(inch)
NEW PETIT CUT
WITH
HOLE
NEW PETIT CUT
NEW PETIT CUT
*
*
NP-DCGW21.50.5-GA2
21.51-GA2
21.52-GA2
32.50.5-GA2
32.51-GA2
32.52-GA2
21.51-GS2
32.50.5-GS2
32.51-GS2
32.52-GS2
21.50.5-GN2
21.51-GN2
21.52-GN2
32.50.5-GN2
32.51-GN2
32.52-GN2
32.51-FA2
32.52-FA2
21.50.5-FS2
21.51-FS2
21.52-FS2
32.50.5-FS2
32.51-FS2
32.52-FS2
21.51-TS2
21.52-TS2
32.50.5-TS2
32.51-TS2
32.52-TS2
32.51-G2
32.52-G2
32.52-F2
1 TNP-DCGW32.51-G2
1
32.52-G2
BF-DCGT32.51-TA2
32.52-TA2
NP-DCGW070202GA2
070204GA2
070208GA2
11T302GA2
11T304GA2
11T308GA2
070204GS2
11T302GS2
11T304GS2
11T308GS2
070202GN2
070204GN2
070208GN2
11T302GN2
11T304GN2
11T308GN2
11T304FA2
11T308FA2
070202FS2
070204FS2
070208FS2
11T302FS2
11T304FS2
11T308FS2
070204TS2
070208TS2
11T302TS2
11T304TS2
11T308TS2
11T304G2
11T308G2
11T308F2
TNP-DCGW11T304G2
11T308G2
.008
a s
.016
a s
.031
.008
a s
.016
a s
BF-DCGT11T304TA2
11T308TA2
.016
.031

*1 aThis
Coated
CBN
CBN
Applicable
Holder Page
Sintered Alloy
POSI
7
B042

MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
NP-DCGW 2 1.5 0.5 GA2
a s
.031
.016
.008
.016
.031
a a
a a
.008
.016
.031
.008
.016
.031
.016
C031
C032
D009
D013
D039
D040
E008
E013
E014
a a
.031
a a
.008
.016
.031
.008
.016
.031
.016
.031
.008
.016
.031
.016
.031
.031
.016
.031
C031
C032
D009
D013
D039
D040
E008
E013
E014
C031
C032
D009
D013
D039
D040
E008
E013
E014
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
CBN
Cast Iron
Order Number
(ISO) Number
(inch)
NEW PETIT CUT
NEW PETIT CUT
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
NP-DCGW21.50.5GA
21.51GA
21.52GA
32.50.5GA
32.51GA
32.52GA
32.50.5GS
32.51GS
21.50.5GN
21.51GN
21.52GN
32.50.5GN
32.51GN
32.52GN
21.50.5G
21.51G
21.52G
32.50.5G
32.51G
32.52G
21.50.5F
21.51F
32.50.5F
32.51F
32.52F
21.50.5T
21.51T
32.50.5T
32.51T
32.52T
NP-DCMW21.51G
32.51G
NP-DCGW070202GA
070204GA
070208GA
11T302GA
11T304GA
11T308GA
11T302GS
11T304GS
070202GN
070204GN
070208GN
11T302GN
11T304GN
11T308GN
070202G
070204G
070208G
11T302G
11T304G
11T308G
070202F
070204F
11T302F
11T304F
11T308F
070202T
070204T
11T302T
11T304T
11T308T
NP-DCMW070204G
11T304G
.008
.016
.031
.008
.016
.031
DCMW21.50.5
21.51
32.50.5
32.51
DCMW070202
070204
11T302
11T304
Applicable
Holder Page
Sintered Alloy
Work
Material
H
K
S
POSI
7
.008
WITH
HOLE
a a
.016
a a
.008
.016
.031
.008
.016
.031
.008
.016
.031
.008
a a
.016
a a
.031
a a
.008
.016
.008
.016
a r
.031
r r
C031
C032
D009
D013
D039
D040
E008
E013
E014
.008
.016
.008
.016
.031
a
a
.016
.016
.008
r r
.016
r r
.008
r r
.016
a s
r r
C031
C032
D009
D013
D039
D040
E008
E013
E014
C031
C032
D009
D013
D039
D040
E008
E013
E014
IDENTIFICATION
B002
HONING
B011
B043
60
TC
TYPE INSERTS
WITH HOLE
Work
Material
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
Order Number
(ISO) Number
Corner
Radius
(inch)
NEW PETIT CUT
WITH
HOLE
NEW PETIT CUT
CBN
NP-TCGW1.81.50.5-GA3
1.81.51-GA3
1.81.52-GA3
21.50.5-GA3
21.51-GA3
21.52-GA3
2.521-GA3
2.522-GA3
32.51-GA3
32.52-GA3
21.51-FA3
21.52-FA3
21.51-FS3
21.52-FS3
21.51-TS3
21.52-TS3
NP-TCGW21.51GA
21.52GA
32.51GA
32.52GA
NP-TCGW090202GA3
090204GA3
090208GA3
110202GA3
110204GA3
110208GA3
130304GA3
130308GA3
16T304GA3
16T308GA3
110204FA3
110208FA3
110204FS3
110208FS3
110204TS3
110208TS3
NP-TCGW110204GA
110208GA
16T304GA
16T308GA
.008
.016
.031
.008
.016
TCMW21.50.5
21.51
TCMW110202
110204
.008
r r
.016
r r

a
r
Coated
CBN
.031
.016
.031
.016
.031
Applicable
Holder Page
Sintered Alloy
POSI
7
B044
H
K
S

MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
NP-TCGW 1.8 1.5 0.5 GA3
C035
E015
E016
.016
a a
.031
a a
.016
.031
.016
.031
.016
.031
.016
.031
C035
E015
E016
C035
E015
E016
TP
Work
Material
H
K
S
NP-TPGB 1.5 1.5 1 GA3

Stable Cutting
General Cutting
CBN
Unstable Cutting
Hardened Materials
Cast Iron
Order Number
(ISO) Number
(inch)
NEW PETIT CUT
NEW PETIT CUT
NEW PETIT CUT
NEW PETIT CUT
NP-TPGB1.51.51-GA3
1.51.52-GA3
1.81.51-GA3
1.81.52-GA3
221-GA3
222-GA3
321-GA3
322-GA3
1.81.50.5-FS3
1.81.51-FS3
220.5-FS3
221-FS3
222-FS3
321-FS3
322-FS3
NP-TPGX1.51.50.5-GS3
1.51.51-GS3
1.81.50.5-GS3
1.81.51-GS3
221-GS3
222-GS3
NP-TPMB1.51.51G
1.81.51G
221G
321G
NP-TPGX1.81.51G
1.81.52G
221G
222G
1.51.50.5F
1.51.51F
1.81.50.5F
1.81.51F
221F
222F
1.51.50.5T
1.51.51T
1.81.50.5T
1.81.51T
221T
222T
NP-TPGB080204GA3
080208GA3
090204GA3
090208GA3
110304GA3
110308GA3
160304GA3
160308GA3
090202FS3
090204FS3
110302FS3
110304FS3
110308FS3
160304FS3
160308FS3
NP-TPGX080202GS3
080204GS3
090202GS3
090204GS3
110304GS3
110308GS3
NP-TPMB080204G
090204G
110304G
160304G
NP-TPGX090204G
090208G
110304G
110308G
080202F
080204F
090202F
090204F
110304F
110308F
080202T
080204T
090202T
090204T
110304T
110308T
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
.016
.031
.016
Applicable
Holder Page
Sintered Alloy
60
TYPE INSERTS
WITH HOLE
POSI
11
.031
.016
s s
.031
s s
.016
s s
.031
s s
WITH
HOLE
E007
.008
.016
.008
.016
.031
.016
s
s
.031
.008
.016
.008
.016
.016
.031
.016
.016
.016
.016
E007
.016
.031
.016
a a
.031
a a
.008
.016
.008
.016
.016
.031
a
a
.008
.016
.008
.016
.016
a a
.031
a a
IDENTIFICATION
B002
HONING
B011
B045
60
TP
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
Order Number
(ISO) Number
Corner
Radius
(inch)
TPGX1.51.50.5
1.51.51
1.51.52
1.81.50.5
1.81.51
1.81.52
220.5
221
222
321
322
331
332
WITH
HOLE
TPGX080202
080204
080208
090202
090204
090208
110302
110304
110308
160304
160308
160404
160408

a
r
Coated
CBN
CBN
.008
.016
.031
.008
s s
s s
r r
s s
s s
.031
r r
.008
r r
a a
.016
.016
.031
a a
.016
a r
.031
a r
.016
r r
.031
r r
Applicable
Holder Page
Sintered Alloy
POSI
11
B046
H
K
S

MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
Work
Material
TPGX 1.5 1.5 0.5
TYPE INSERTS
WITH HOLE
VB
Work
Material
H
K
S
NP-VBGW 3 3 1 GA2
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Order Number
(ISO) Number
(inch)
NEW PETIT CUT
NEW PETIT CUT
NP-VBGW331-GA2
332-GA2
221-GS2
222-GS2
331-GS2
332-GS2
221-FS2
222-FS2
331-FS2
332-FS2
221-TS2
222-TS2
331-TS2
332-TS2
NP-VBGW331GA
332GA
331G
332G
NP-VBGW160404GA2
160408GA2
110304GS2
110308GS2
160404GS2
160408GS2
110304FS2
110308FS2
160404FS2
160408FS2
110304TS2
110308TS2
160404TS2
160408TS2
NP-VBGW160404GA
160408GA
160404G
160408G
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
.016
a s
.031
a s
.016
Applicable
Holder Page
Sintered Alloy
POSI
5
.031
.016
a a
.031
a a
.016
.031
CBN
35
TYPE INSERTS
WITH HOLE
.016
.031
.016
.031
.016
C028
C029
D010
D014
E009
E010
H013
WITH
HOLE
.031
.016
.031
.016
.031
C031
C032
E014
IDENTIFICATION
B002
HONING
B011
B047
35
VC
Work
Material

Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
Order Number
(ISO) Number
Corner
Radius
(inch)
NEW PETIT CUT
WITH
HOLE
NEW PETIT CUT
NP-VCGW331-GA2
332-GA2
331-FS2
332-FS2
NP-VCGW160404GA2
160408GA2
160404FS2
160408FS2
.016
a s
.031
a s
.016
.031
NP-VCGW331GA
332GA
NP-VCGW160404GA
160408GA
.016
.031

Coated
CBN
CBN
Applicable
Holder Page
Sintered Alloy
POSI
7
B048
H
K
S
NP-VCGW 3 3 1 GA2
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
TYPE INSERTS
WITH HOLE
C036
E016
E017
C036
E016
E017
WC
Work
Material
H
K
S
NP-WCGW 1.5 1.5 0.5 GA3

Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Order Number
(ISO) Number
(inch)
NEW PETIT CUT
NEW PETIT CUT
NP-WCGW1.51.50.5-GA3
1.51.51-GA3
21.50.5-GA3
21.51-GA3
32.51-GA3
32.52-GA3
1.51.50.5-GS3
1.51.51-GS3
21.50.5-GS3
21.51-GS3
32.51-GS3
32.52-GS3
NP-WCMW1.51.51FA
1.51.52FA
1.51.50.5G
1.51.51G
21.50.5G
21.51G
32.51G
32.52G
NP-WCGWL30202GA3
L30204GA3
040202GA3
040204GA3
06T304GA3
06T308GA3
L30202GS3
L30204GS3
040202GS3
040204GS3
06T304GS3
06T308GS3
NP-WCMWL30204FA
L30208FA
L30202G
L30204G
040202G
040204G
06T304G
06T308G
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
.008
.016
.008
.016
.016
.031
.008
.016
.008
.016
.016
.031
Applicable
Holder Page
Sintered Alloy
CBN
80
TYPE INSERTS
WITH HOLE
POSI
7
WITH
HOLE
C037
E017
020
.016
.031
.008
a a
.016
a a
.008
a a
.016
a a
.016
a a
.031
a a
C037
E017
020
IDENTIFICATION
B002
HONING
B011
B049
RBG
TYPE INSERTS
WITHOUT HOLE
H
K
S
General Cutting
Cast Iron
Dimensions (inch)
CBN
Shape
Order Number
RBG10
12
16
POSI
5
6
Unstable Cutting
(ISO) Number
RBG10
12
16
D1
S1
L1
D4
.394
.197
.354
.197
.472
.236
.433
.236
.630
.315
.512
.315
Applicable
Holder Page
Work
Material
Stable Cutting
Hardened Materials
MB710
CBN
WITHOUT
HOLE
INSERTS
RTG TYPE
WITHOUT HOLE
H
K
S
General Cutting
Hardened Materials
Cast Iron
Dimensions (inch)
Shape
Order Number
RTG05A
06A
07A
08A
10A
B050
(ISO) Number
RTG05A
06A
07A
08A
10A

MB825
CBN
a
r
Unstable Cutting
D1
S1
L1
D4
.197
.138
.295
.098
.236
.138
.295
.138
.276
.197
.433
.138
.315
.197
.433
.177
.394
.256
.551
.217
Applicable
Holder Page
Work
Material
Stable Cutting
C045
Work
Material
H
K
S

Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Order Number
(ISO) Number
(inch)
SPG320.5
321
322
323
421
422
423
432
433
SPGN090302
090304
090308
090312
120304
120308
120312
120408
120412
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
.008
r r
.016
a r
.031
a r
.047
r r
.016
a s
.031
a s
.047
r r
.031
r r
.047
r r
IDENTIFICATION
Applicable
Holder Page
Sintered Alloy
CBN
SP
90
SPG 3 2 0.5
TYPE INSERTS
WITHOUT HOLE
POSI
11
B002
WITHOUT
HOLE
B051
60
TB
H
K
S
Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Shape
Order Number
(ISO) Number
Corner
Radius
(inch)
TBG1.211
1.212
TBGN060104
060108
Coated
CBN
CBN
.016
s r
.031
s r
Applicable
Holder Page
Sintered Alloy
POSI
5
11
WITHOUT
HOLE
B052

MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
CBN
Work
Material
TBG 1.2 1 1
TYPE INSERTS
WITHOUT HOLE

a
r
TP
Work
Material
H
K
S
TPG 1.8 1.5 1

Stable Cutting
General Cutting
Unstable Cutting
Hardened Materials
Cast Iron
Order Number
(ISO) Number
(inch)
TPG1.81.51
220.5
221
222
321
322
323
332
432
TPGN090204
110302
110304
110308
160304
160308
160312
160408
220408
Coated
CBN
CBN
MBC010
MBC020
BC8020
MB810
MB8025
MB825
MB835
MB710
MB730
MB4020
Shape
Corner
Radius
.016
r r
.008
r r
.016
a a
.031
r r
.016
a a
.031
a a
a a
.047
r r
.031
r r
.031
r r
IDENTIFICATION
Applicable
Holder Page
Sintered Alloy
CBN
60
TYPE INSERTS
WITHOUT HOLE
POSI
5
11
B002
WITHOUT
HOLE
B053
PCD TURNING INSERTS [NEGATIVE]
80
CN

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Shape
NEW PETIT CUT
NEG
WITH
HOLE
Order Number
NP-CNMM430.5RF
430.5LF
431RF
431LF
432RF
432LF
CNMA431
432
55
DN
(ISO) Number
NP-CNMM120402R-F
120402L-F
120404R-F
120404L-F
120408R-F
120408L-F
CNMA120404
120408
TYPE INSERTS
WITH HOLE
Work
Material
Corner
Radius
(inch)
MD220
PCD
Work
Material
NP-CNMM 4 3 0.5 RF
TYPE INSERTS
WITH HOLE
.008
.008
.016
.016
.031
.031
.016
.031
Applicable
Holder Page
C006
009
E021
E024
H006
008
C006
009
E021
E024
H006
008
NP-DNMM 4 3 0.5 RF
Stable Cutting

General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
NEW PETIT CUT
B054
Order Number
NP-DNMM430.5RF
430.5LF
431RF
431LF
432RF
432LF
DNGA431
432
(ISO) Number
NP-DNMM150402R-F
150402L-F
150404R-F
150404L-F
150408R-F
150408L-F
DNGA150404
150408
s : Inventory maintained in Japan. r : Non stock, produced to order only
(inch)
MD220
Shape
Corner
Radius
.008
.008
.016
.016
.031
.031
.016
.031
Applicable
Holder Page
C010
012
E024
H009
011
C010
012
E024
H009
011
SN
Work
Material

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
NEW PETIT CUT
Order Number
(ISO) Number
NP-SNMM431RF
431LF
432RF
432LF
NP-SNMM120404R-F
120404L-F
120408R-F
120408L-F
.016
.016
.031
.031
SNGA431
432
SNGA120404
120408
.016
.031
60
TN
Applicable
Holder Page
C014
017
E022
E025
NEG
WITH
HOLE
C014
017
E022
E025
NP-TNMM 3 3 0.5 RF
TYPE INSERTS
WITH HOLE
Work
Material
(inch)
MD220
Shape
Corner
Radius
PCD
90
NP-SNMM 4 3 1 RF
TYPE INSERTS
WITH HOLE

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
NEW PETIT CUT
Order Number
NP-TNMM330.5RF
330.5LF
331RF
331LF
332RF
332LF
TNGA330.5
331
332
(ISO) Number
NP-TNMM160402R-F
160402L-F
160404R-F
160404L-F
160408R-F
160408L-F
TNGA160402
160404
160408
(inch)
MD220
Shape
Corner
Radius
.008
.008
.016
.016
.031
.031
.008
.016
.031
Applicable
Holder Page
IDENTIFICATION
C018
023
E022
E025
C018
023
E022
E025
B002
B055
PCD TURNING INSERTS [NEGATIVE]
35
VN
NEG
WITH
HOLE
B056
Work
Material
NP-VNMM 3 3 0.5 RF
Stable Cutting

General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Shape
NEW PETIT CUT
Order Number
NP-VNMM330.5RF
330.5LF
331RF
331LF
332RF
332LF
VNGA331
332
(ISO) Number
NP-VNMM160402R-F
160402L-F
160404R-F
160404L-F
160408R-F
160408L-F
VNGA160404
160408
s : Inventory maintained in Japan. r : Non stock, produced to order only.
Corner
Radius
(inch)
MD220
PCD
TYPE INSERTS
WITH HOLE
.008
.008
.016
.016
.031
.031
.016
.031
Applicable
Holder Page
C024
026
E023
E026
C024
026
E023
E026
SN
Work
Material

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Order Number
(ISO) Number
(inch)
SNG431
432
SNGN120404
120408
MD220
Shape
Corner
Radius
.016
.031
Applicable
Holder Page
C014
017
E025
PCD
90
SNG 4 3 1
TYPE INSERTS
WITHOUT HOLE
NEG
WITHOUT
HOLE
IDENTIFICATION
B002
B057
PCD TURNING INSERTS [POSITIVE]
80
CC
Work
Material

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Shape
NEW PETIT CUT
Corner
Radius
(ISO) Number
Order Number
(inch)
MD220
PCD
NP-CCMH 2 1.5 0.5
TYPE INSERTS
WITH HOLE
NP-CCMH21.50.5
21.51
NP-CCMH060202
060204
.008
.016
NP-CCMW03S102
03S104
04T002
04T004
NP-CCMW03S102
03S104
04T002
04T004
.008
.016
.008
.016
CCMW21.50.5
21.51
32.50.5
32.51
CCMW060202
060204
09T302
09T304
.008
.016
.008
.016
Applicable
Holder Page
C030
D008
D012
E006
E012
E013
POSI
7
11
WITH
HOLE
NEW PETIT CUT
80
CP
Work
Material
C030
D008
D012
E006
E012
E013
NP-CPMH 2.5 1.5 0.5
TYPE INSERTS
WITH HOLE
E012
E013

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
NEW PETIT CUT
B058
(ISO) Number
Order Number
NP-CPMH2.51.50.5
2.51.51
320.5
321
NP-CPMH080202
080204
090302
090304
.008
.016
.008
.016
CPGT2.51.50.5
2.51.51
320.5
321
CPGT080202
080204
090302
090304
.008
.016
.008
.016

(inch)
MD220
Shape
Corner
Radius
Applicable
Holder Page
E006
E006
DC
Work
Material
NP-DCMT 2 1.5 0.5 RF
Stable Cutting

General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
NEW PETIT CUT
Order Number
NP-DCMT21.50.5RF
21.50.5LF
21.51RF
21.51LF
32.50.5RF
32.50.5LF
32.51RF
32.51LF
DCMW21.50.5
21.51
32.50.5
32.51
90
SP
(ISO) Number
NP-DCMT070202R-F
070202L-F
070204R-F
070204L-F
11T302R-F
11T302L-F
11T304R-F
11T304L-F
DCMW070202
070204
11T302
11T304
Work
Material
.008
.008
.016
.016
.008
.008
.016
.016
.008
.016
.008
.016
Applicable
Holder Page
C031
C032
D009
D013
D039
D040
E008
E013
E014
POSI
7
11
WITH
HOLE
C031
C032
D009
D013
D039
D040
E008
E013
E014
SPGX 3 2 1
TYPE INSERTS
WITH HOLE
(inch)
MD220
Shape
Corner
Radius
PCD
55
TYPE INSERTS
WITH HOLE

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Order Number
SPGX321
322
(ISO) Number
SPGX090304
090308
(inch)
MD220
Shape
Corner
Radius
.016
.031
Applicable
Holder Page
IDENTIFICATION
B002
B059
60
TC
Work
Material

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Shape
(ISO) Number
Order Number
Corner
Radius
(inch)
MD220
PCD
TCMW 2 1.5 0.5
TYPE INSERTS
WITH HOLE
TCMW21.50.5
21.51
TCMW110202
110204
.008
.016
TCGW1.210.5
1.211
1.212
TCGW060102
060104
060108
.008
.016
.031
POSI
7
WITH
HOLE
B060

Applicable
Holder Page
C035
E015
E016
TP
Work
Material

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
NEW PETIT CUT
NEW PETIT CUT
Order Number
NP-TPMX1.81.50.5RF
1.81.50.5LF
1.81.51RF
1.81.51LF
1.81.52RF
1.81.52LF
220.5RF
220.5LF
221RF
221LF
222RF
222LF
320.5RF
320.5LF
321RF
321LF
322RF
322LF
NP-TPMH1.51.50.5RF
1.51.50.5LF
1.51.51RF
1.51.51LF
1.81.50.5RF
1.81.50.5LF
1.81.51RF
1.81.51LF
220.5RF
220.5LF
221RF
221LF
320.5RF
320.5LF
321RF
321LF
TPGT320.5RF
320.5LF
321RF
321LF
(ISO) Number
NP-TPMX090202R-F
090202L-F
090204R-F
090204L-F
090208R-F
090208L-F
110302R-F
110302L-F
110304R-F
110304L-F
110308R-F
110308L-F
160302R-F
160302L-F
160304R-F
160304L-F
160308R-F
160308L-F
NP-TPMH080202R-F
080202L-F
080204R-F
080204L-F
090202R-F
090202L-F
090204R-F
090204L-F
110302R-F
110302L-F
110304R-F
110304L-F
160302R-F
160302L-F
160304R-F
160304L-F
TPGT160302R-F
160302L-F
160304R-F
160304L-F
(inch)
MD220
Shape
Corner
Radius
.008
.008
.016
.016
.031
.031
.008
.008
.016
.016
.031
.031
.008
.008
.016
.016
.031
.031
.008
.008
.016
.016
.008
.008
.016
.016
.008
.008
.016
.016
.008
.008
.016
.016
.008
.008
.016
.016
Applicable
Holder Page
IDENTIFICATION
PCD
60
NP-TPMX 1.8 1.5 0.5 RF
TYPE INSERTS
WITH HOLE
POSI
11
WITH
HOLE
E007
B002
B061
60
TP
POSI
11
WITH
HOLE
B062
Work
Material

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Shape
Order Number
TPGV1.81.50.5RF
1.81.50.5LF
1.81.51RF
1.81.51LF
220.5RF
220.5LF
221RF
221LF
TPGX1.51.50.5
1.51.51
1.51.52
1.81.50.5
1.81.51
1.81.52
220.5
221
222
321
322
: Inventory maintained in Japan.
(ISO) Number
TPGV090202R-F
090202L-F
090204R-F
090204L-F
110302R-F
110302L-F
110304R-F
110304L-F
TPGX080202
080204
080208
090202
090204
090208
110302
110304
110308
160304
160308
Corner
Radius
(inch)
MD220
PCD
TPGV 1.8 1.5 0.5 RF
TYPE INSERTS
WITH HOLE
.008
.008
.016
.016
.008
.008
.016
.016
.008
.016
.031
.008
.016
.031
.008
.016
.031
.016
.031
Applicable
Holder Page
VB
Work
Material
NP-VBGT 2 2 V5 RF
Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Order Number
NP-VBGT22V5RF
220.2RF
220.5RF
221RF
(ISO) Number
NP-VBGT1103V5R-F
110301R-F
110302R-F
110304R-F
(inch)
MD220
Shape
Corner
Radius
.002
.004
.008
.016
Applicable
Holder Page
C028
C029
D010
D014
E009
E010
PCD
35
TYPE INSERTS
WITH HOLE
POSI
5
7
WITH
HOLE
35
VC
TYPE INSERTS
WITH HOLE
Work
Material
NP-VCGT 1.5 1.5 V5 RF
Stable Cutting
Size Thickness Corner Raduis

General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Order Number
NP-VCGT1.51.5V5RF
1.51.50.2RF
1.51.50.5RF
1.51.51RF
22V5RF
220.2RF
220.5RF
221RF
(ISO) Number
NP-VCGT0802V5R-F
080201R-F
080202R-F
080204R-F
1103V5R-F
110301R-F
110302R-F
110304R-F
(inch)
MD220
Shape
Corner
Radius
.002
.004
.008
.016
.002
.004
.008
.016
Applicable
Holder Page
IDENTIFICATION
C036
E016
E017
B002
B063
80
WC
Work
Material

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Shape
Order Number
WCMW1.51.50.5
1.51.51
21.50.5
21.51
32.51
32.52
POSI
7
11
WITH
HOLE
80
WP
(ISO) Number
WCMWL30202
L30204
040202
040204
06T304
06T308
Work
Material
(inch)
.008
.016
.008
.016
.016
.031
WPGT 2
TYPE INSERTS
WITH HOLE
Corner
Radius
MD220
PCD
WCMW 1.5 1.5 0.5
TYPE INSERTS
WITH HOLE
Applicable
Holder Page
C037
E017
020
1.5
0.5

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Order Number
WPGT21.50.5
21.51
320.5
321
B064
(ISO) Number
WPGT040202
040204
060302
060304
(inch)
MD220
Shape
Corner
Radius
.008
.016
.008
.016
Applicable
Holder Page
E009
Work
Material
Stable Cutting
DEGX 4 3 0.5 RF
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Order Number
DEGX430.5RF
430.5LF
431RF
431LF
(ISO) Number
DEGX150402R-F
150402L-F
150404R-F
150404L-F
(inch)
MD220
Shape
Corner
Radius
.008
.008
.016
.016
Applicable
Holder Page
C041
PCD
DE
55
TYPE INSERTS
WITH HOLE
POSI
20
WITH
HOLE
TE
60
Work
Material
TEGX
TYPE INSERTS
WITH HOLE
3 2
0.5

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Order Number
(ISO) Number
(inch)
MD220
Shape
Corner
Radius
TEGX320.5R
320.5L
321R
321L
TEGX160302R
160302L
160304R
160304L
.008
.008
.016
.016
TEGX320.5
321
TEGX160302
160304
.008
.016
Applicable
Holder Page
C042
E028
C042
E028
IDENTIFICATION
B002
B065
35
VD
POSI
15
Work
Material
Stable Cutting

General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Shape
Order Number
VDGX320.5RF
320.5LF
321RF
321LF
(ISO) Number
VDGX160302R-F
160302L-F
160304R-F
160304L-F
WITH
HOLE
B066
VDGX 3 2 0.5 RF
Corner
Radius
(inch)
MD220
PCD
TYPE INSERTS
WITH HOLE
.008
.008
.016
.016
Applicable
Holder Page
C043
SP
Work
Material

Stable Cutting
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Order Number
SPG320.5
321
322
323
421
422
423
60
(ISO) Number
SPGN090302
090304
090308
090312
120304
120308
120312
TP
TYPE INSERTS
WITHOUT HOLE
Work
Material
Stable Cutting
(inch)
MD220
Shape
Corner
Radius
.008
.016
.031
.047
.016
.031
.047
Applicable
Holder Page
PCD
90
SPG 3 2 0.5
TYPE INSERTS
WITHOUT HOLE
POSI
11
WITHOUT
HOLE
TPG 2 2 0.5
General Cutting
Unstable Cutting
Non-Ferrous Metal
PCD
Order Number
TPG220.5
221
222
320.5
321
322
323
(ISO) Number
TPGN110302
110304
110308
160302
160304
160308
160312
(inch)
MD220
Shape
Corner
Radius
.008
.016
.031
.008
.016
.031
.047
Applicable
Holder Page
IDENTIFICATION
B002
B067
GUIDE TO EXTERNAL TURNING TOOLS

z Organized according to turning insert shape.
FIGURE SHOWING TOOLING APPLICATION

uses illustrations and arrows to depict the possible machining
applications such as external turning, copying, facing, and
chamfering together with cutting edge lead angles.
TYPE OF TOOL HOLDER

indicates the rst four letters of the order number,
as well as cutting applications.
GEOMETRY
TITLE OF PRODUCT BY INSERT TYPE
PRODUCT SECTION
CHIP BREAKER BY
CUTTING APPLICATION
i i INSERTS
CN TOOL
HOLDERS
Medium
MH
MCLN
95
L2
Medium
L1
Standard
(4)
Medium to
Semi-Heavy
GH
(4)
(4)
Stainless
CBN
H1
H2
Order Number
Stock
(3,4)
(4)
H1
L1
L2
(3,4)
Stock
Order Number
H2
Shim
F1
Light
SA
Medium
L1
Standard
Right hand tool

holder shown.
(4)
*2
Dimensions (inch)
Insert Number
R L
95
Right hand tool
holder shown.
Finish
FH
Shim Pin Clamp Bridge Spring Clamp Screw Wrench
Medium
MA
(4)
95
L2
MS
95
Multiple Clamp Type

M Holder
External turning
Facing
F1
F1
(4)
Medium
MA
Medium
MH
(4)
Medium to
Semi-Heavy
GH
(3,4,5,6)
(4)
(4,5,6)
Stainless
CBN
MS
(4,5,6)
(3,4,5,6)
(4)
*3
Dimensions (inch)
Insert Number
R L
H1
L1
L2
H2
F1
Shim
Shim Pin Clamp Bridge Clamp Screw
DCLNR/L-123
a a
32p
.750
.750 4.500 1.000
.750 1.000
LLSCN33
*1 LLP23 DCK2211 DCS2 DC0520T TKY15F
(LLSCN32)
MCLNR/L-123
a a
32p
-124B
a a
43p *
-124
a a
43p
.750
.750 4.500 1.250
.750 1.000 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
-163
a a
32p
-163
a a
LLSCN33
(LLSCN32)
-164C
a a
43p *
-164D
a a
*1
43p * 1.000 1.000 6.000 1.250 1.000 1.250 ICSN433
NL46
CL20
XNS48
43p
1.000 1.000 6.000 1.250 1.000 1.250 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
-165C
a a
54p
1.000 1.000 5.000 1.375 1.000 1.250 ICSN533
NL58
CL12
XNS510
-165D
a a
54p
1.000 1.000 6.000 1.375 1.000 1.250 ICSN533
NL58
CL12
XNS510
-166C
a a
1.000 1.000 5.000 1.500 1.000 1.250 ICSN633
NL68
-166D
a a
1.000 1.000 6.000 1.500 1.000 1.250 ICSN633
-204D
a a
-205D
a a
-206D
a a
CNMA
CNMG
CNMM
CNGG
32p
1.000 1.000 6.000 1.000 1.000 1.250
-164
a a
-204
a a
43p
-244
a a
43p
use shim no.LLSCN32 with .187inch thick insert. When using .187inch thick inserts, the shim should be ordered separately.
*12 Please
* Clamp Torque (lbf-in) : DC0520T=31, DC0621T=44
*
*
.750
.750 4.500 1.187
.750 1.000 ICSN322
NL34
CL7
.750
.750 4.500 1.250
*
.750 1.000 ICSN433
NL46
CL20
XNS48
1.000 1.000 6.000 1.187 1.000 1.250 ICSN322
NL34
CL7
XNS36
NL46
CL20
*
1.000 1.000 5.000 1.250 1.000 1.250 ICSN433
64p
CNMA
CNMG
CNMM
CNGG
XNS36
XNS48
CL12
XNS510
NL68
CL12
XNS510
*
1.250 1.250 6.000 1.187 1.250 1.500 ICSN433
NL46
CL20
XNS48
54p
1.250 1.250 6.000 1.375 1.250 1.500 ICSN533
NL58
CL12
XNS510
64p
1.250 1.250 6.000 1.500 1.250 1.500 ICSN633
NL68
CL12
XNS510
64p
43p *
-244D
a a
43p *
*
1.500 1.500 6.000 1.187 1.500 2.000 ICSN433
-244E
a a
43p *
*
1.500 1.500 7.000 1.187 1.500 2.000 ICSN433
NL46
CL20
XNS48
-246D
a a
64p
1.500 1.500 6.000 1.500 1.500 2.000 ICSN633
NL68
CL12
XNS510
-246E
a a
64p
1.500 1.500 7.000 1.500 1.500 2.000 ICSN633
NL68
CL12
XNS510
-854D
a a
43p *
-856D
a a
64p
NL46
CL20
XNS48
*
1.250 1.000 6.000 1.187 1.250 1.250 ICSN433
NL46
CL20
XNS48
1.250 1.000 6.000 1.500 1.250 1.250 ICSN633
NL68
CL12
XNS510
1 (Opt.) See page E008 for different radius.

3 Clamp Torque (lbf-in) : XNS36=30, XNS48=45, XNS510=70
Light
SA
Finish
FH
H1
DOUBLE CLAMP Type

B
External turning
Facing
H2
DCLN
2 For inserts without hole, remove shim pin and add below.
Shim Screw
S46
Chipbreaker
CBC4

Work Material
P
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB280HB)
Grade
Cutting Speed
(SFM)
Finish
FY
NX3035
850 1210
Light
SY
NX3035
770 1100
Medium
MS
UE6110
850 1440
Finish
FH
NX3035
655 935
Cutting Mode Breaker
Light
SA
UE6110
685 1160
Medium
MA
UE6110
620 1065
Work Material
Grade
Cutting Speed
(SFM)
Finish
FH
US735
345 655
Light
SA
US735
Medium
MS
US735
275 540
Light
MA
UC5115
520 965
Medium
Standard
UC5115
520 965
Semi-Heavy Flat Top
UC5115
505 915
M
Stainless Steel
( < 200HB)
K
Cast Iron
( < 350MPa)
310 605
(Note) Insert photo is an example. Letters show chip breaker style, gures show inscribed circle.
C006
DCLN type inserts
A068A073
MCLN type inserts
A068A073
SPARE PARTS
M001
CBN & PCD inserts
B022B024, B054
CBN & PCD inserts
B022B024, B035, B054
TECHNICAL DATA
N001
LEGEND FOR STOCK

STATUS MARK
is shown on the left hand page
of each double-page spread.
REFERENCE PAGE
FOR APPLICABLE INSERTS
C007
PAGE REFERENCE
SPARE PARTS
indicates reference pages giving details of TECHNICAL DATA
inserts that are applicable to the product. indicates reference pages,
including the above, on the right hand

PRODUCT STANDARDS
for each work material classication, indicates recommended cutting

conditions according to the ISO categories for cutting grades, P, M and K.
indicates order numbers,

stock status (per right/left hand),
applicable inserts, dimensions,
and spare parts.
aTo
C000
Order :
Please specify order number and hand of tool (right/left).
TURNING

CLASSIFICATION............................................... C002
IDENTIFICATION ................................................ C004
STANDARD HOLDERS
CNooINSERTS TOOL HOLDERS....................................... C006
DNooINSERTS TOOL HOLDERS....................................... C010
RNooINSERTS TOOL HOLDERS....................................... C013
SNooINSERTS TOOL HOLDERS ....................................... C014
TNooINSERTS TOOL HOLDERS ....................................... C018
VNooINSERTS TOOL HOLDERS ....................................... C024
WNooINSERTS TOOL HOLDERS ....................................... C027
VBooINSERTS TOOL HOLDERS ....................................... C028
CCooINSERTS TOOL HOLDERS....................................... C030
DCooINSERTS TOOL HOLDERS....................................... C031
RCooINSERTS TOOL HOLDERS....................................... C033
SCooINSERTS TOOL HOLDERS ....................................... C034
TCooINSERTS TOOL HOLDERS ....................................... C035
VCooINSERTS TOOL HOLDERS ....................................... C036
WCooINSERTS TOOL HOLDERS ....................................... C037
XCooINSERTS TOOL HOLDERS ....................................... C038
RPooINSERTS TOOL HOLDERS ....................................... C040
DEooINSERTS TOOL HOLDERS ....................................... C041
TEooINSERTS TOOL HOLDERS ....................................... C042
VDooINSERTS TOOL HOLDERS ....................................... C043
RGooINSERTS TOOL HOLDERS ...................................... C044
TL HOLDER (TAPER LOCK TYPE) .......................... C045
Arranged by Alphabetical order

*C006
DCLN
C010 MDJN
C008
C010
C011
C012
C013
C016
C017
C014
C015
C022
C022
C018
C024
C025
C025
C027
C009
C008
C007
C009
DCRN
DDJN
DDPN
DDQN
DRGN
DSDN
DSKN
DSRN
DSSN
DTCN
DTFN
DTGN
DVJN
DVPN
DVVN
DWLN
MCFN
MCGN
MCLN
MCRN
C011
C013
C016
C017
C014
C015
C020
C021
C021
C023
C019
C018
C020
C024
C026
C027
C030
C031
C041
C031
MDPN
MRGN
MSDN
MSKN
MSRN
MSSN
MTAN
MTCN
MTEN
MTFN
MTGN
MTJN
MTRN
MVJN
MVLN
MWLN
SCLC
SDJC
SDJE
SDNC
C032
C033
C040
C033
C044
C034
C034
C035
C042
C035
C042
C029
C028
C036
C043
C036
C043
C028
C037
C038
C045
SDXC
SRDC
SRDP
SRGC
SRSG
SSBC
SSSC
STFC
STFE
STGC
STGE
SVHB
SVJB
SVJC
SVJD
SVPC
SVPD
SVVB
SWLC
SXZC
TLH
C001
CLASSIFICATION
External Turning
Facing
' = 95
Tool Holder
M Holder
SP Holder
C002
' = 93
External
Turning
' = 62 30'
72 30'
' = 90 91
Features
'
DOUBLE
CLAMP Holder
External Turning
Copying
'
'
'
New double clamp type.

Holds inserts securely.
Excellent cutting edge
tolerance.
a Economical negative
insert.
a Recommended with
CBN grade insert
a
a
a
Negative rake clamp and

locking pin toolholders.
a Insert is securely held
by a shim pin and clamp
bridge.
a Index operation is easy
to perform.
a (Opt.) Single clamp
available as clamp on or
pin lock holder.
DCLN
DWLN
DDJN
DVJN
DDPN
DVVN
DTGN
^ C006
^ C027
^ C010
^ C024
^ C011
^ C025
^ C018
MCLN
MWLN
MDJN MTJN MVJN
MDPN
MCGN MTGN MTAN
^ C007
^ C027
^ C010 ^ C018 ^ C024
^ C011
^ C008 ^ C019 ^ C020
SCLC
SWLC
SDJC SVJC SVJB
SDNC
SVVB
STGC
^ C030
^ C037
^ C031 ^ C036 ^ C028
^ C031
^ C028
^ C035
Small shank toolholder

system using a 5,7
and 11 positive inserts
retained by screw-on
system.
25 rhombic insert for

proling and face relief.
a Machine 300 of a sphere.
a Machine face relief to
60 angle.
a The cycle time can be
reduced due to only one
holder.
PROFILE Holder
AL Holder
Shank size .625 square

thru 1.000 square with
screw-on method.
a Suitable for nishing
aluminum or
non-ferrous metals and
for chatter control on
small diameters.
Applies taper-lock type
clamping method.
The double tapered
insert is clamped by
inserting small end into
the tapered clamp hole.
a Round insert produces
good surface nish.
TL Holder
SR Holder
High positive cutting

rake angle (24) round
insert retained by
screw-on system.
a Rough machining of
super alloys, stainless
and tough-to-cut
materials.
SDJE
SVJD
STGE
^ C041
^ C043
^ C042
' = 0 -1
' = 5
'
'
'
'
'
'
'
Special Design
DCRN DSRN
DSDN
DSSN
DSKN
DTCN
DTFN DVPN DDQN
DRGN
^ C008
^ C016
^ C015
^ C017
^ C022
^ C022
^ C013
^ C014
^ C025 ^ C012
MCRN MSRN MTRN MTEN
MSDN
MSSN
MSKN MCFN MTCN MTFN
MVLN
MRGN
^ C009 ^ C014 ^ C020 ^ C021
^ C016
^ C015
^ C017
^ C026
^ C013
^ C009 ^ C021 ^ C023
SDXC
^ C032
SSBC
SSSC
STFC
^ C034
^ C034
^ C035
e e
u e
' = 45 ' = 15
Selection Standard
Specialized
' = 45
External Turning,
Copying
Operation Efciency
' = 60
Facing
Copying
Facing
Clamp Rigidity
' = 75
External Turning,
Facing, Chamfering
Economical
Low Cutting Resistance
(Sharpness)
External Turning,
Chamfering
External Turning
SRGC
^ C033
SVHB SVPC SRDC SRDPR/L/N
^ C029 ^ C036
^ C033
^ C040
SXZC
^ C038
STFE
SVPD
^ C042
^ C043
TLHR/L
TLHN
^ C045
^ C045
SRSGR/L SRSGN
^ C044
^ C044
(Note) e : 1st recommendation. u : 2nd recommendation.
C003
IDENTIFICATION
DOUBLE CLAMP Holder, M Holder, SP Holder, PROFILE Holder, AL Holder, TL Holder, SR Holder
Double Clamp
Type
M
80Rhombic 55Rhombic
T
Square
X
Special
Design
Multiple Clamp Screw Clamp

Type
Type
Special Special
Design Design
Triangluar 35Rhombic
z Method of Holding
Trigon
x Insert Shape
v Insert Relief Angle

B
Round
c Tool Style
n Tool Size [Height (H1) and Width (B)] (inch)
06
08
10
12
16
20
24
85
H1 .375 .500 .625 .750 1.000 1.250 1.500 1.250

B .375 .500 .625 .750 1.000 1.250 1.500 1.000
5
In case of B=H1, the number will represent the number of sixteeths of B and H1.
In case of B H1, the rst digit represents the number of eighths of B, and the second digit
represents the number of quarters of H1.
m Insert Size
15
20
Inscribed Circle
of Insert (inch)
.188
.219
.250
.313
.375
.500
.625
2.5
2.5
2.5
11
b Hand of Tool
R
, Tool Length (L1) (inch)
C004
.750 1.000
4.500
5.000
6.000
7.000
METHOD OF HOLDING
Type
Structure
Double Clamp
DOUBLE CLAMP
Holder
b
v
zShim
xShim Pin
cSpring
vClamp Bridge
bClamp Screw
nInsert
z
x
Multiple Clamp
For insert with hole
(M Holder)
c
x
z
b
v c
zShim
xShim Pin
cClamp Screw
vClamp Bridge
bInsert
z
x
Multiple Clamp
For insert without hole
(Opt.)
(M Holder)
v
n
nv c
zShim
xShim Screw
cClamp Screw
vClamp Bridge
bInsert
nChipbreaker
b
z
x
Screw Clamp
SP Holder
AL Holder
SR Holder
x
z
zInsert
xInsert Screw
Double Clamp with

Screw and Clamp Bridge
(PROFILE Holder)
b
v
z
b
c
zInsert
xInsert Screw
cSpring
vClamp Bridge
bClamp Screw
C005
ii INSERTS
CN TOOL HOLDERS
DCLN
DOUBLE CLAMP Type
F1
95
L2
L1
Light
SA
Medium
MA
Medium
MH
(4)
(4)
(4)
(4)
Medium
Medium to
Semi-Heavy
Stainless
CBN
Standard
GH
MS
95
H1
6
H2
Finish
FH
External turning
Facing
Order Number
Stock
(3,4)
(4)
H1
L1
L2
(3,4)
(4)
*2
Dimensions (inch)
Insert Number
R L
Right hand tool

holder shown.
H2
F1
Shim
DCLNR/L-123
a a
32p
.750
.750 4.500 1.000
LLSCN33
.750 1.000
(LLSCN32)
-124
a a
43p
.750
.750 4.500 1.250
.750 1.000 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
-163
a a
-164
a a
-204
-244
CNMA
CNMG
CNMM
CNGG
LLSCN33
(LLSCN32)
32p
1.000 1.000 6.000 1.000 1.000 1.250
43p
a a
43p
a a
43p
Please use shim no.LLSCN32 with .187inch thick insert. When using .187inch thick inserts, the shim should be ordered separately.
*21 Clamp
Torque (lbf-in) : DC0520T=31, DC0621T=44
*
C006
DCLN type inserts
A068A073
CBN & PCD inserts
B022B024, B054
Multiple Clamp Type

M Holder
F1
95
L2
Stock
Order Number
.750
32p
-124B
a a
2
43p *
-163
a a
32p
Medium
MH
(4)
(4)
(4)
(4,5,6)
Medium to
Semi-Heavy
Stainless
CBN
Right hand tool

holder shown.
GH
(3,4,5,6)
MS
(4,5,6)
(3,4,5,6)
(4)
*3
L1
L2
H2
F1
Shim
.750 4.500 1.187
.750 1.000 ICSN322
NL34
CL7
XNS36
.750 4.500 1.250
*1
.750 1.000 ICSN433
NL46
CL20
XNS48
1.000 1.000 6.000 1.187 1.000 1.250 ICSN322
NL34
CL7
XNS36
NL46
CL20
XNS48
*
1.000 1.000 6.000 1.250 1.000 1.250 ICSN433
NL46
CL20
XNS48
.750
43p *
*
1.000 1.000 5.000 1.250 1.000 1.250 ICSN433
-164D
a a
43p *
-165C
a a
54p
1.000 1.000 5.000 1.375 1.000 1.250 ICSN533
NL58
CL12
XNS510
-165D
a a
54p
1.000 1.000 6.000 1.375 1.000 1.250 ICSN533
NL58
CL12
XNS510
-166C
a a
64p
1.000 1.000 5.000 1.500 1.000 1.250 ICSN633
NL68
CL12
XNS510
64p
-166D
*
*
H1
a a
Medium
MA
Medium
Standard
H1
Insert Number
a a
-164C
Light
SA
Dimensions (inch)
R L
MCLNR/L-123
L1
H2
95
Finish
FH
External turning
Facing
a a
CNMA
CNMG
CNMM
CNGG
1.000 1.000 6.000 1.500 1.000 1.250 ICSN633
NL68
CL12
XNS510
2
*1
43p * 1.250 1.250 6.000 1.187 1.250 1.500 ICSN433
NL46
CL20
XNS48
1.250 1.250 6.000 1.375 1.250 1.500 ICSN533
NL58
CL12
XNS510
1.250 1.250 6.000 1.500 1.250 1.500 ICSN633
NL68
CL12
XNS510
NL46
CL20
XNS48
*
1.500 1.500 7.000 1.187 1.500 2.000 ICSN433
NL46
CL20
XNS48
1.500 1.500 6.000 1.500 1.500 2.000 ICSN633
NL68
CL12
XNS510
-204D
a a
-205D
a a
54p
-206D
a a
64p
-244D
a a
43p *
*
1.500 1.500 6.000 1.187 1.500 2.000 ICSN433
-244E
a a
43p *
-246D
a a
64p
-246E
a a
64p
1.500 1.500 7.000 1.500 1.500 2.000 ICSN633
NL68
CL12
XNS510
-854D
a a
*1
43p * 1.250 1.000 6.000 1.187 1.250 1.250 ICSN433
NL46
CL20
XNS48
-856D
a a
64p
NL68
CL12
XNS510
1.250 1.000 6.000 1.500 1.250 1.250 ICSN633
1 (Opt.) See page E008 for different radius.

MCLN
Shim Screw
S46
Chipbreaker
CBC4

Work Material

Finish
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB 280HB)
Light
FY
SY
Grade
Cutting Speed
(SFM)
NX3035
850 1210
NX3035
770 1100
Medium
MS
UE6110
850 1440
Finish
FH
NX3035
655 935
Light
SA
UE6110
685 1160
Medium
MA
UE6110
620 1065
Work Material
Cutting Speed
(SFM)
Finish
FH
US735
345 655
Light
SA
US735
310 605
Medium
MS
US735
275 540
Light
MA
UC5115
520 965
Medium
Standard
UC5115
520 965
Semi-Heavy Flat Top
UC5115
505 915
M
Stainless Steel
( < 200HB)
K
Cast Iron
( < 350MPa)
Grade
MCLN type inserts
A068A073
SPARE PARTS
M001
CBN & PCD inserts
B022B024, B035, B054
TECHNICAL DATA
N001
C007
ii INSERTS
CN TOOL HOLDERS
MCGN
Multiple Clamp Type

M Holder
F1
90
L2
H2
Stock
Order Number
Insert Number
-164C
r r
-164D
a a
-165D
a a
-166D
r r
H1
(4)
(4)
(4,5,6)
Medium to
Semi-Heavy
Stainless
CBN
Right hand tool

holder shown.
L1
L2
GH
(4,5,6)
MS
(4,5,6)
(4,5,6)
(4)
*3
H2
Shim
F1

NL46
CL20
XNS48
NL46
CL20
XNS48
NL46
CL20
XNS48
54p
1.000 1.000 6.000 1.313 1.000 1.250 ICSN533
NL58
CL12
XNS510
64p
1.000 1.000 6.000 1.625 1.000 1.250 ICSN633
NL68
CL9
XNS510
See page E008 for different radius.

*13 (Opt.)
Clamp Torque (lbf-in) : XNS48=45, XNS510=70
*
*2 For inserts without hole, remove shim pin and add below.
Shim Screw
S46
DOUBLE CLAMP Type
External turning
Chipbreaker
CBC4
Finish
FH
Light
SA
Medium
MA
Medium
MH
F1
DCRN
(4)
*1
.750 .750 4.500 1.250 .750 1.000 ICSN433
2
*1
43p * 1.000 1.000 5.000 1.250 1.000 1.250 ICSN433
2
*1
43p * 1.000 1.000 6.000 1.250 1.000 1.250 ICSN433
CNMA
CNMG
CNMM
CNGG
Medium
MH
Medium
2
43p *
r r
Medium
MA
Dimensions (inch)
R L
MCGNR/L-124
Light
SA
Standard
L1
H1
90
Finish
FH
External turning
Facing
75
L2
(4)
(4)
(4)
Medium
Medium to
Semi-Heavy
Stainless
Standard
L1
GH
(4)
MS
H2
75
H1
Order Number
Stock
R L
H1
DCRNR/L-124
43p
-164
a a CNGG
43p
CNMG
CNMM
(4)
(4)
(4)
Dimensions (inch)
Insert Number
a a CNMA
Right hand tool

holder shown.
.750
L1
L2
.750 4.500 1.250
Shim
H2
F1
.750
.888 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
* Clamp Torque (lbf-in) : DC0621T=44

Work Material

Finish
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB 280HB)
FY
Grade
Cutting Speed
(SFM)
NX3035
850 1210
Light
SY
NX3035
770 1100
Medium
MS
UE6110
850 1440
Finish
FH
NX3035
655 935
Light
SA
UE6110
685 1160
Medium
MA
UE6110
620 1065
Work Material
Finish
Stainless Steel
( < 200HB)
K
Cast Iron
( < 350MPa)
Grade
Cutting Speed
(SFM)
FH
US735
345 655
Light
SA
US735
310 605
Medium
MS
US735
275 540
Light
MA
UC5115
520 965
Medium
Standard
UC5115
520 965
Semi-Heavy Flat Top
UC5115
505 915
C008
a : Inventory maintained.
MCGN type inserts
A068A073
DCRN type inserts
A068A073
CBN & PCD inserts
B022B024, B035, B054
Multiple Clamp Type

M Holder
F1
75
L2
Stock
Order Number
a r
-164C
a a
-164D
a a
-165D
a r
-166D
r r
H1
Insert Number
B
H1
r r
-165D
a a
-166D
r r
(4,5,6)
*3
L1
L2
H2
F1
Shim

NL46
CL20
XNS48
NL46
CL20
XNS48
NL46
CL20
XNS48
64p
1.000 1.000 6.000 1.343 1.000 1.250 ICSN633
NL68
CL12
XNS510
Shim Screw
S46
Multiple Clamp Type

M Holder
Light
SA
Medium
MA
Medium
MH
F1
Chipbreaker
CBC4
Finish
FH
90
L2
L1
H1
(4)
(4)
(4)
(4,5,6)
Medium
Medium to
Semi-Heavy
Stainless
CBN
Standard
Right hand tool

holder shown.
GH
(4,5,6)
MS
(4,5,6)
(4,5,6)
(4)
*3
Dimensions (inch)
H1
43p *
CNMA
CNMG
CNMM
CNGG
(4,5,6)
XNS510
H2
-164D
(4,5,6)
MS
CL9
Insert Number
r r
a a
GH
NL58
R L
-164C
Standard
(4,5,6)
1.000 1.000 6.000 1.343 1.000 1.250 ICSN533
MCFNR/L-124
(4)
Stainless
54p
90
Order Number
(4)
Medium to
Semi-Heavy
*1
.750 .750 4.500 1.250 .750 .750 ICSN433
2
*1
43p * 1.000 1.000 5.000 1.250 1.000 1.250 ICSN433
2
*1
43p * 1.000 1.000 6.000 1.250 1.000 1.250 ICSN433
Facing
Stock
Medium
MH
(4)
2
43p *
CNMA
CNMG
CNMM
CNGG
Medium
MA
Medium
Right hand tool

holder shown.

*13 (Opt.)
*
MCFN
Light
SA
Dimensions (inch)
R L
MCRNR/L-124B
L1
H2
75
Finish
FH
External turning
MCRN
.750
L1
L2
H2
.750 4.500 1.250
F1
Shim

1
*
.750 1.000 ICSN433
NL46
CL20
XNS48
NL46
CL20
XNS48
*
1.000 1.000 6.000 1.250 1.000 1.250 ICSN433
NL46
CL20
XNS48
54p
1.000 1.000 6.000 1.380 1.000 1.250 ICSN533
NL58
CL12
XNS510
64p
1.000 1.000 6.000 1.500 1.000 1.250 ICSN633
NL68
CL9
XNS510
*
1.000 1.000 5.000 1.250 1.000 1.250 ICSN433
43p *
43p *

*13 (Opt.)
* Clamp Torque (lbf-in) : XNS48=45, XNS510=70
Shim Screw
S46
Chipbreaker
CBC4
MCRN type inserts
A068A073
MCFN type inserts
A068A073
SPARE PARTS
M001
CBN & PCD inserts
B022B024, B035, B054
TECHNICAL DATA
N001
C009
ii INSERTS
DN TOOL HOLDERS
DDJN
DOUBLE CLAMP Type
F1
L1
Light
SA
Medium
MA
Medium
MH
(4)
(4)
(4)
(4)
Medium to
Semi-Heavy
Stainless
G Class
CBN
MS
GH
MJ
Order Number
Stock
a a
-124
a a
-163
a a
-164
a a
-204
a a
-244
a a
H1
DNMA
DNMG
DNMM
DNGA
DNGG
DNGM
DNMX
Right hand tool

holder shown.
(4)
(3,4)
(4)
L1
L2
(4)
*2
Dimensions (inch)
Insert Number
R L
DDJNR/L-123
H1
H2
93
L2
93
Finish
FH
External turning
Copying
H2
Shim
F1
33p
.750
.750 4.500 1.188
.750 1.000 LLSDN32 LLP23 DCK2211 DCS2 DC0520T TKY15F
43p
.750
.750 4.500 1.375
.750 1.000
LLSDN43 LLP24
*1 (LLP14)
*1 DCK2613 DCS1 DC0621T TKY20F
(LLSDN42)
33p
1.000 1.000 6.000 1.188 1.000 1.250 LLSDN32 LLP23 DCK2211 DCS2 DC0520T TKY15F
43p
1.000 1.000 6.000 1.375 1.000 1.250
43p
43p
LLSDN43
*1
(LLSDN42)
LLSDN43
1.250 1.250 6.000 1.375 1.250 1.500
*1
(LLSDN42)
LLSDN43
1.500 1.500 6.000 1.500 1.500 2.000
*1
(LLSDN42)
LLP24
(LLP14)
LLP24
(LLP14)
LLP24
(LLP14)
use shim no.LLSDN42 and shim pin LLP14 with .25inch thick insert. When using .25inch thick inserts, the shim and shim pin should
*1 Please
be ordered separately.
*2 Clamp Torque (lbf-in) : DC0520T=31, DC0621T=44
MDJN
Multiple Clamp Type

M Holder
F1
5
93
L2
93
Medium
MA
Medium
MH
H1
(4)
(4)
(4)
(4)
Medium to
Semi-Heavy
Stainless
G Class
CBN
MS
Right hand tool

holder shown.
(4)
MJ
(3,4)
(4)
(4)
*2
Dimensions (inch)
Insert Number
R L
MDJNR/L -123
Light
SA
GH
L1
H2
Order Number
Stock
Finish
FH
External turning
Copying
H1
L1
L2
H2
F1
Shim
a a
33p
.750
.750 4.500 1.250
.750 1.000 IDSN322
NL33L
CL7
XNS36
-124B
a a
43p
.750
.750 4.500 1.250
.750 1.000 IDSN433
NL46
CL7
XNS36
-163
a a
-164C
a a
-164D
a a
-165D
a a
-204D
a a
DNMA
DNMG
DNMM
DNGA
DNGG
DNGM
DNMX
33p
1.000 1.000 5.000 1.250 1.000 1.250 IDSN322
NL33L
CL7
XNS36
43p
1.000 1.000 5.000 1.250 1.000 1.250 IDSN433
NL46
CL20
XNS48
1.000 1.000 6.000 1.250 1.000 1.250 IDSN433
43p
54p *
43p
-205D
a a
54p *
-244D
a a
43p
NL46
CL20
XNS48
*1 NL58
1.000 1.000 6.000 1.469 1.000 1.250 IDSN533
CL12
XNS510
1.250 1.250 6.000 1.250 1.250 1.500 IDSN433
NL46
CL20
XNS48
*
1.250 1.250 6.000 1.469 1.250 1.500 IDSN533
NL58
CL12
XNS510
1.500 1.500 6.000 1.250 1.500 2.000 IDSN433
NL46
CL20
XNS48
See page E008 for different thickness.

*12 (Opt.)
Clamp Torque (lbf-in) : XNS36=30, XNS48=45, XNS510=70
*
C010
DDJN type inserts
A074A078
MDJN type inserts
A074A078
CBN & PCD inserts
B025B027, B054
DOUBLE CLAMP Type
6230
L2
62
30
Finish
Light
FH
SA
Medium
MA
Medium
MH
F1
External turning
Copying
L1
(4)
(4)
(4)
(4)
Medium to
Semi-Heavy
Stainless
G Class
CBN
MS
GH
MJ
H1
H2
11
(4)
Order Number
H1
DDPNN-164
43p
(4)
L1
L2
(4)
*2
Dimensions (inch)
Stock Insert Number

DNMA
DNMG
DNMM
DNGA
DNGG
DNGM
(4)
H2
Shim
F1
1.000 1.000 6.000 1.500 1.000
LLSDN43 LLP24
*1 (LLP14)
(LLSDN42)
.500
*1 Please
*2 Clamp Torque (lbf-in) : DC0621T=44
MDPN
Multiple Clamp Type

M Holder
6230
L2
L1
Light
SA
Stock
11
(4)
(4)
(4)
(4)
Stainless
G Class
CBN
MS
GH
H1
MDPNN-164D
-165D
*
*
MJ
(4)
(4)
43p
L1
L2
(4)
*2
Dimensions (inch)
Insert Number
DNMA
DNMG
DNMM
DNGA
DNGG
DNGM
Medium
MH
Medium to
Semi-Heavy
(4)
Order Number
Medium
MA
H1
62
30
H2
Finish
FH
F1
External turning
Copying
DDPN
H2
F1
1.000 1.000 6.000 1.750 1.000
Shim
.500 IDSN433
NL46
CL12
XNS510
*1
54p * 1.000 1.000 6.000 1.922 1.000 .500 IDSN533
NL58
CL12
XNS510
1 (Opt.) See page E008 for different thickness.

2 Clamp Torque (lbf-in) : XNS510=70

Work Material

Finish
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB 280HB)
Light
FY
SY
Grade
Cutting Speed
(SFM)
NX3035
850 1210
NX3035
770 1100
Medium
MS
UE6110
850 1440
Finish
FH
NX3035
655 935
Light
SA
UE6110
685 1160
Medium
MA
UE6110
620 1065
Work Material
Grade
Cutting Speed
(SFM)
FH
US735
345 655
Light
SA
US735
310 605
Medium
MS
US735
275 540
Light
MA
UC5115
520 965
Medium
Standard
UC5115
520 965
Semi-Heavy Flat Top
UC5115
505 915
Finish
Stainless Steel
( < 200HB)
K
Cast Iron
( < 350MPa)
DDPN type inserts
A074A078
MDPN type inserts
A074A078
SPARE PARTS
M001
CBN & PCD inserts
B025B027, B054
TECHNICAL DATA
N001
C011
ii INSERTS
DN TOOL HOLDERS
Order Number
Stock
Medium
MA
Medium
MH
L1
(4)
(4)
(4)
(4)
Medium to
Semi-Heavy
Stainless
G Class
CBN
MS
GH
MJ
H1
a a
DNMA
DNMG
DNMM
DNGA
DNGG
DNGM
43p
H1
Right hand tool

holder shown.
(4)
(4)
(4)
L1
L2
(4)
*2
Dimensions (inch)
Insert Number
R L
DDQNR/L-164
Light
SA
6
H2
10730
L2
107
30
Finish
FH
DOUBLE CLAMP Type
F1
DDQN
External turning
Copying
H2
Shim
F1
1.000 1.000 6.000 1.375 1.000 1.250
LLSDN43 LLP24
*1
(LLSDN42) (LLP14)
*1 Please
*2 Clamp Torque (lbf-in) : DC0621T=44

Work Material

Finish
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB 280HB)
Light
FY
SY
Grade
Cutting Speed
(SFM)
NX3035
850 1210
NX3035
770 1100
Medium
MS
UE6110
850 1440
Finish
FH
NX3035
655 935
Light
SA
UE6110
685 1160
Medium
MA
UE6110
620 1065
Work Material
Grade
Cutting Speed
(SFM)
FH
US735
345 655
Light
SA
US735
310 605
Medium
MS
US735
275 540
Light
MA
UC5115
520 965
Medium
Standard
UC5115
520 965
Semi-Heavy Flat Top
UC5115
505 915

Finish
Stainless Steel
( < 200HB)
K
Cast Iron
( < 350MPa)
C012
DDQN type inserts
A074A078
CBN & PCD inserts
B025B027, B054
i i INSERTS
RN TOOL HOLDERS
DRGN
DOUBLE CLAMP Type
Medium
Standard
F1
External turning
Copying
(4)
L2
L1
Flat top
H1
H2
(4)
Right hand tool holder shown.
Stock
Order Number
R L
DRGNR/L-124
a a
-164
a a
-204
a a
H1
43p
RNMA
RNMG
Dimensions (inch)
Insert Number
.750
L1
L2
H2
.750 4.500 1.188
Shim
F1
.750 1.000 LLSRN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
43p
1.000 1.000 6.000 1.188 1.000 1.250 LLSRN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
43p
1.250 1.250 6.000 1.188 1.250 1.500 LLSRN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
Medium

Multiple Clamp Type
M Holder
External turning
Copying
Flat top
L1
H1
H2
(3,4,6)
Medium
L2
Order Number
Stock
Insert Number
H1
32
r a
(4)
*3
Dimensions (inch)
R L
MRGNR/L -123B
Medium
Standard
5
F1
MRGN
.750
1
2
-124B
a r
43 **
-163
r r
32
.750
L1
.750 4.500
1.000 1.000 6.000
H2
.937
.750 1.000 IRSN32
NL33
CL6
XNS36
1
.750 1.000 IRSN43*
NL46
CL9
XNS59
NL34
CL6
XNS36
NL46
CL9
XNS59
NL46
CL9
XNS59
NL46
CL9
XNS59
.750 4.500 1.187
F1
Shim
L2
.937 1.000 1.250 IRSN32
1
1
43 **2 1.000 1.000 5.000 1.187 1.000 1.250 IRSN43*
1
1
43 **2 1.000 1.000 6.000 1.187 1.000 1.250 IRSN43*
1
1
43 **2 1.250 1.250 6.000 1.187 1.250 1.500 IRSN43*
-164C
a a
-164D
a a
-204D
a r
-206D
r r
64
1.250 1.250 6.000 1.125 1.250 1.500 IRSN63
NL68
CL12
XNS58
-246
r r
64
1.500 1.500 7.000 1.125 1.500 2.000 IRSN63
NL68
CL12
XNS58
RNMA
RNMG
(Opt.) See page E008 for different thickness.

*13 Clamp
Torque (lbf-in) : XNS36=30, XNS58=70, XNS59=70
*
Shim Screw
S46
Chipbreaker
CBR4
DRGN type inserts
A079
MRGN type inserts
A079
SPARE PARTS
M001
CBN inserts
B036
TECHNICAL DATA
N001
C013
i i INSERTS
SN TOOL HOLDERS
DSRN
DOUBLE CLAMP Type
Finish
Light
SA
FH
Medium
MA
Medium
MH
B
75
L2
L1
(4)
(4)
(4)
Medium to
Semi-Heavy
Stainless
CBN
GH
(4)
MS
75
Order Number
Stock
-164
H1
SNMA
a a SNMG
SNMM
a a SNGA
SNGG
43p
43p
Right hand tool

holder shown.
(4)
(4)
(4)
Dimensions (inch)
Insert Number
R L
DSRNR/L-124
H1
H2
.750
L1
L2
.750 4.500 1.250
Shim
H2
F1
.750
.878 LLSSN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
1.000 1.000 6.000 1.250 1.000 1.128 LLSSN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
Clamp Torque (lbf-in) : DC0621T=44
Multiple Clamp Type

M Holder
External turning
F1
MSRN
75
L2
Order Number
Stock
-103
-123
-124B
*
*
H1
a a
-164D
a a
-165
a a
-165C
a a
-166
a a
-205D
a a
H1
L1
L2
(3,4)
(4)
(4)
Medium to
Semi-Heavy
Stainless
CBN
(4,6)
MS
(4,5,6,8)
H2
F1
.500 4.500 1.062
.500
.625
.625 4.500 1.062
.625
1
2
.750
.750 4.500 1.062
.750
1
2
.750
.750 4.500 1.234
.750
43p **
SNMA
SNMG
SNMM
SNGA
SNGG
.500
32p **
a a
Medium
MH
(3,4,5,6)
(4)
*3
1
2
32p **
a a
Right hand tool

holder shown.
1
2
32p **
r r
-164C
Insert Number
r r
Medium
MA
Dimensions (inch)
R L
MSRNR/L -83
Light
SA
GH
L1
H2
75
Finish
FH
F1
External turning
Shim
*1 NL34
.658 ISSN322
*1 NL34
.783 ISSN322
*1 NL34
.908 ISSN322
*1 NL46
.878 ISSN433
1
*1 NL46
43p **2 1.000 1.000 5.000 1.234 1.000 1.128 ISSN433
1
*1 NL46
43p **2 1.000 1.000 6.000 1.234 1.000 1.128 ISSN433
54p
54p
64p *
54p
CL6
XNS36
CL6
XNS36
CL6
XNS36
CL9
XNS59
CL9
XNS59
CL9
XNS59
1.000 1.000 6.000 1.343 1.000 1.100 ISSN533
NL58
CL12
XNS510
1.000 1.000 5.000 1.343 1.000 1.100 ISSN533
NL58
CL12
XNS510
*
1.000 1.000 6.000 1.500 1.000 1.068 ISSN633
NL68
CL12
XNS510
1.250 1.250 6.000 1.343 1.250 1.350 ISSN533
NL58
CL12
XNS510
CL12
XNS510
CL12
XNS510
CL12
XNS510
CL24
XNS610
-206D
a a
-246D
a a
-246E
a a
*1 NL68
64p * 1.250 1.250 6.000 1.500 1.250 1.312 ISSN633
1
*1 NL68
64p * 1.500 1.500 6.000 1.500 1.500 1.818 ISSN633
1
*1 NL68
64p * 1.500 1.500 7.000 1.500 1.500 1.818 ISSN633
-248
a a
86p
1.500 1.500 7.000 1.625 1.500 1.768 ISSN846
1 (Opt.) See page E008 for different thickness or radius.

3 Clamp Torque (lbf-in) : XNS36=30, XNS59=70, XNS510=70, XNS610=135
NL810
Insert
SNpN3pp
SNpN4pp
Shim Screw
S34
S46
Chipbreaker
CBS3
CBS4
C014
a
r
DSRN type inserts
A080A084
MSRN type inserts
A080A084, A099
CBN & PCD inserts
B028, B029, B036, B055, B057
DSSN
DOUBLE CLAMP Type
External turning
Chamfering
Finish
-164
(4)
(4)
Stainless
CBN
GH
(4)
MS
Right hand tool

holder shown.
(4)
(4)
(4)
Dimensions (inch)
Insert Number
R L
H1
SNMA
a a SNMG
SNMM
a a SNGA
SNGG
(4)
Medium to
Semi-Heavy
L1
45
DSSNR/L -124
Medium
MH
43p
.750
43p
L1
L2
H2
.750 4.500 1.250
Shim
F1
.750
.659
LLSSN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
1.000 1.000 6.000 1.250 1.000
.909
MSSN
Multiple Clamp Type

M Holder
Finish
45
L2
45
(4)
(4)
Stainless
CBN
Insert Number
H1
-124B
a r
-164C
r r
-164D
a a
-205D
r r
-206D
r r
SNMA
SNMG
SNMM
SNGA
SNGG
MS
(4,5,6)
(3,4,5,6)
(4)
*3
L1
L2
H2
F1
1
2
.500
.500 4.500 1.062
.500
1
2
.750
.750 4.500 1.234
.750
32p **
r r
(4,6)
Dimensions (inch)
R L
MSSNR/L -83
Medium
MH
(3,4)
Right hand tool

holder shown.
Order Number
Medium
MA
Medium to
Semi-Heavy
GH
L1
8
Stock
Light
SA
FH
F1
External turning
Chamfering
F1
45
L2
Order Number
Medium
MA
45
Stock
Light
SA
FH
43p **
1
2
43p **
64p *
*1
.391 ISSN322
*1
.662 ISSN433
*1
.912 ISSN433
*1
.912 ISSN433
1.000 1.000 5.000 1.234 1.000
1
43p **2 1.000 1.000 6.000 1.234 1.000
54p
Shim
1.250 1.250 6.000 1.375 1.250 1.078 ISSN533

1
*
.992 ISSN633
1.250 1.250 6.000 1.484 1.250
See page E008 for different thickness or radius.

*13 (Opt.)
*
NL34
CL6
XNS36
NL46
CL9
XNS59
NL46
CL9
XNS59
NL46
CL9
XNS59
NL58
CL9
XNS510
NL68
CL9
XNS510
Insert
SNpN3pp
SNpN4pp
Shim Screw
S34
S46
Chipbreaker
CBS3D
CBS4D

Work Material

Finish
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB 280HB)
Light
FY
SY
Grade
Cutting Speed
(SFM)
NX3035
850 1210
NX3035
770 1100
Medium
MS
UE6110
850 1440
Finish
FH
NX3035
655 935
Light
SA
UE6110
685 1160
Medium
MA
UE6110
620 1065
Work Material
Grade
Cutting Speed
(SFM)
FH
US735
345 655
Light
SA
US735
310 605
Medium
MS
US735
275 540
Light
MA
UC5115
520 965
Medium
Standard
UC5115
520 965
Semi-Heavy Flat Top
UC5115
505 915
Finish
Stainless Steel
( < 200HB)
K
Cast Iron
( < 350MPa)
DSSN type inserts
A080A084
MSSN type inserts
A080A084, A099
SPARE PARTS
M001
CBN & PCD inserts
B028, B029, B036, B055, B057
TECHNICAL DATA
N001
C015
ii INSERTS
SN TOOL HOLDERS
DSDN
DOUBLE CLAMP Type
45
L2
Light
SA
(4)
CBN
H1
DSDNN-124
-164
43p
43p
(4)
MS
H1
H2
(4)
Stainless
(4)
(4)
Dimensions (inch)
Stock Insert Number

SNMA
SNMG
SNMM
SNGA
SNGG
Medium
MH
(4)
(4)
Order Number
Medium
MA
Medium to
Semi-Heavy
GH
L1
45
Finish
FH
F1
External turning
Chamfering
.750
L1
L2
H2
.750 4.500 1.375
Shim
F1
.750
.375
1.000 1.000 6.000 1.375 1.000
.500
MSDN
Multiple Clamp Type

M Holder
45
L2
45
Finish
Light
SA
FH
Medium
MA
Medium
MH
F1
External turning
Chamfering
L1
(3,4)
(4)
(4)
Medium to
Semi-Heavy
Stainless
CBN
GH
(4,6)
MS
H2
H1
730
(4,5,6)
Order Number
Stock
Insert Number
-103
-123
-124
1
2
32p **
a
a
-164
-165
-166
-206
1
2
1
2
32p **
SNMA
SNMG
SNMM
SNGA
SNGG
32p **
1
2
43p **
1
43p **2
54p
*3
.500
L1
L2
H2
Shim
F1

1
*
ISSN322
.500 4.500 1.000
.500 .250
.625
.625 4.500 1.000
.750
.750 4.500 1.000
*1
.625 .313 ISSN322
*1
.750 .375 ISSN322
*1
.750 .750 4.500 1.375 .750 .375 ISSN433
*1
1.000 1.000 6.000 1.375 1.000 .500 ISSN433
1.000 1.000 6.000 1.625 1.000 .500
ISSN533
*1
1.000 1.000 6.000 1.625 1.000 .500 ISSN633
1
*1
64p * 1.250 1.250 7.000 1.625 1.250 .625 ISSN633
64p *
( 4)
Dimensions (inch)
H1
MSDNN-83
(3,4,5,6)

*13 (Opt.)
*
NL34
CL6
XNS36
NL34
CL6
XNS36
NL34
CL6
XNS36
NL46
CL9
XNS59
NL46
CL9
XNS59
NL58
CL12
XNS510
NL68
CL12
XNS510
NL68
CL12
XNS510
Insert
SNpN3pp
SNpN4pp
Shim Screw
S34
S46
Chipbreaker
CBS3D
CBS4D
C016
a
r
DSDN type inserts
A080A084
MSDN type inserts
A080A084, A099
CBN & PCD inserts
B028, B029, B036, B055, B057
75
L2
L1
DSKNR/L-124
-164
43p
43p
(4)
(4)
Stainless
CBN
Right hand tool

holder shown.
H1
SNMA
a a SNMG
SNMM
a a SNGA
SNGG
(4)
(4)
MS
(4)
(4)
(4)
Dimensions (inch)
Insert Number
R L
.750
Medium
MH
Medium to
Semi-Heavy
GH
H2
Stock
Medium
MA
H1
Order Number
Light
SA
F1
75
Finish
FH
L1
L2
H2
.750 4.500 1.000
Shim
F1
.750 1.000 LLSSN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
1.000 1.000 6.000 1.000 1.000 1.250 LLSSN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
MSKN
Multiple Clamp Type

M Holder
75
L2
L1
Insert Number
H1
-103
-123
r r
-124B
a a
-164D
a a
-165D
a a
-205D
a a
-206D
SNMA
SNMG
SNMM
SNGA
SNGG
Right hand tool

holder shown.
L1
Finish
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB 280HB)
Light
FY
SY
(4,5,6)
(3,4,5,6)
(4)
*3
L2
H2
F1
Shim
*1 NL34
.625 ISSN322
*1 NL34
.750 ISSN322
.500
.625
.625 4.500 1.000
.625
.750 4.500 1.000
*1 NL34
.750 .875 ISSN322
*1 NL46
.750 1.000 ISSN433
1
2
32p **
.750
1
43p **2 .750 .750 4.500 1.219
1
*1 NL46
43p **2 1.000 1.000 6.000 1.219 1.000 1.250 ISSN433
CL6
XNS36
CL6
XNS36
CL6
XNS36
CL9
XNS59
CL9
XNS59
54p
1.000 1.000 6.000 1.344 1.000 1.250 ISSN533
NL58
CL12
XNS510
54p
1.250 1.250 6.000 1.344 1.250 1.500 ISSN533
NL58
CL12
XNS510
1.250 1.250 6.000 1.500 1.250 1.500 ISSN633
NL68
CL12
XNS510
Insert
SNpN3pp
SNpN4pp

(4,6)
MS
.500 4.500 1.000

*13 (Opt.)
*
Work Material
(4)
CBN
.500
64p *
r r
(4)
Stainless
1
2
32p **
r r
(3,4)
1
2
32p **
r r
Medium
MH
Dimensions (inch)
R L
MSKNR/L -83
Medium
MA
Medium to
Semi-Heavy
GH
H1
H2
Order Number
Light
SA
75
Stock
Finish
FH
F1
Facing
DSKN
DOUBLE CLAMP Type
Facing
Grade
Cutting Speed
(SFM)
NX3035
850 1210
NX3035
770 1100
Medium
MS
UE6110
850 1440
Finish
FH
NX3035
655 935
Light
SA
UE6110
685 1160
Medium
MA
UE6110
620 1065
Work Material
Chipbreaker
CBS3
CBS4
Grade
Cutting Speed
(SFM)
Finish
FH
US735
345 655
Light
SA
US735
310 605
Medium
MS
US735
275 540
Light
MA
UC5115
520 965
Medium
Standard
UC5115
520 965
Semi-Heavy Flat Top
UC5115
505 915
M
Stainless Steel
( < 200HB)
K
Cast Iron
( < 350MPa)
Shim Screw
S34
S46
DSKN type inserts
A080A084
MSKN type inserts
A080A084, A099
SPARE PARTS
M001
CBN & PCD inserts
B028, B029, B036, B055, B057
TECHNICAL DATA
N001
C017
ii INSERTS
TN TOOL HOLDERS
MTJN
Multiple Clamp Type

M Holder
F1
93
L2
Medium
MA
Medium
MH
(3)
(3,4)
(3,4)
Medium to
Semi-Heavy
Stainless
CBN
GH
L1
H2
Stock
Order Number
(3,4)
MS
MTJNR/L -123X
a a
-163X
a a
-164
a a
-165
r a
-204
a a
-205
a a
-245
a a
-246
a r
-854
a r
Right hand tool

holder shown.
(3,4,5,6)
(3,4)
(3)
*2
Dimensions (inch)
Insert Number
R L
H1
L1
L2
H2
Shim
F1
*1 NL34L
.750 .750 4.500 1.000 .750 1.000 ITSN323
1
*1 NL34L
33p * 1.000 1.000 6.000 1.000 1.000 1.250 ITSN323
1
*1 NL46
43p * 1.000 1.000 6.000 1.200 1.000 1.250 ITSN432
1
*1 NL58
54p * 1.000 1.000 6.000 1.375 1.000 1.250 ITSN533
1
33p *
TNMA
TNMG
TNMX
TNMM
TNGA
TNGG
43p *
*
1.250 1.250 6.000 1.200 1.250 1.500 ITSN432
54p *
*
1.250 1.250 6.000 1.375 1.250 1.500 ITSN533
CL6
XNS36
CL6
XNS36
CL9
XNS510
CL9
XNS510
NL46
CL9
XNS510
NL58
CL9
XNS510
CL9
XNS510
CL12
XNS510
CL9
XNS510
*1 NL58
54p * 1.500 1.500 7.000 1.375 1.500 2.000 ITSN533
1
*1 NL68L
66p * 1.500 1.500 7.000 1.375 1.500 2.000 ITSN636
1
*1 NL46
43p * 1.250 1.000 6.000 1.200 1.250 1.250 ITSN432
1

2 Clamp Torque (lbf-in) : XNS36=30, XNS510=70
External turning
DOUBLE CLAMP Type
F1
DTGN
91
L2
Order Number
Stock
DTGNR/L-123
a a
-163
a a
-164
a a
-204
a a
-244
a a
TNMA
TNMG
TNMM
TNGA
TNGG
33p
Medium
MH
(3)
(3)
(3)
Stainless
CBN
GH
L1
(3)
MS
H1
(3)
(3)
L1
L2
(3)
*2
Dimensions (inch)
H1
33p
Medium
MA
Medium to
Semi-Heavy
Right hand tool

holder shown.
Insert Number
R L
Light
SA
6
H2
91
Finish
FH
*
*
Light
SA
5
H1
93
Finish
FH
External turning
H2
F1
Shim
LLSTN32
.750 .750 4.500 1.000 .750 1.000
(LLSTN33)
LLSTN32
1.000 1.000 6.000 1.000 1.000 1.250
(LLSTN33)
43p
1.000 1.000 6.000 1.250 1.000 1.250 LLSTN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
43p
43p
use shim no.LLSTN33 with .125inch thick insert. When using .125inch thick inserts, the shim should be ordered separately.
*12 Please
Clamp Torque (lbf-in) : DC0520T=31, DC0621T=44
*
C018
MTJN type inserts
A085A091
DTGN type inserts
A085A091
CBN & PCD inserts
B030, B031, B055
F1
90
L2
90
Order Number
-163CX
a a
-163DX
r a
-164C
a a
-164D
H1
r r
-165D
r r
-204D
r a
-205D
a r
-244D
r r
Right hand tool

holder shown.
TNMA
TNMG
TNMM
TNGA
TNGG
Medium
MH
(3)
(3,4)
(3,4)
Medium to
Semi-Heavy
Stainless
CBN
(3,4)
MS
(3,4,5,6)
(3,4)
(3)
*3
L1
L2
H2
F1
1
33p **2 .750 .750 4.500 .937 .750
1
33p **2 1.000 1.000 5.000 .937 1.000
1
33p **2 1.000 1.000 6.000 .937 1.000
1
43p * 1.000 1.000 5.000 1.200 1.000
1
43p * 1.000 1.000 6.000 1.200 1.000
a a
-165C
H1
Insert Number
a a
Medium
MA
Dimensions (inch)
R L
MTGNR/L -123BX
Light
SA
GH
L1
H2
Stock
Finish
FH
Multiple Clamp Type

M Holder
Shim
*1 NL34L
1.000 ITSN323
*1 NL34L
1.250 ITSN323
CL6
XNS36
CL6
XNS36
CL9
XNS36
CL9
XNS510
NL46
CL9
XNS510
NL58
CL9
XNS510
CL9
XNS510
CL9
XNS510
CL9
XNS510
CL9
XNS510
CL9
XNS510
CL9
XNS510
*1 NL34L
1.250 ITSN323
*1 NL46
1.250 ITSN432
1
*
1.250 ITSN432
54p *
*
1.000 1.000 5.000 1.375 1.000 1.250 ITSN533
54p *
43p *
54p *
43p *
*1 NL58
1.000 1.000 6.000 1.375 1.000 1.250 ITSN533
*1 NL46
1.250 1.250 6.000 1.187 1.250 1.500 ITSN432
*1 NL58
1.250 1.250 6.000 1.375 1.250 1.500 ITSN533
*1 NL46
1.500 1.500 6.000 1.375 1.500 2.000 ITSN432
-244E
r r
-245D
r r
1
*1 NL46
43p * 1.500 1.500 7.000 1.375 1.500 2.000 ITSN432
1
*1 NL58
54p * 1.500 1.500 6.000 1.375 1.500 2.000 ITSN533
-245E
r r
54p *
-246D
r r
-246E
r r
-854D
r r
-855D
*1 NL58
1.500 1.500 7.000 1.375 1.500 2.000 ITSN533
1
*1 NL68L
66p * 1.500 1.500 6.000 1.500 1.500 2.000 ITSN636
1
*1 NL68L
66p * 1.500 1.500 7.000 1.500 1.500 2.000 ITSN636
1
*1 NL46
43p * 1.250 1.000 6.000 1.200 1.250 1.250 ITSN432
1
*1 NL58
54p * 1.250 1.000 6.000 1.375 1.250 1.250 ITSN533
1

*13 (Opt.)
* Clamp Torque (lbf-in) : XNS36=30, XNS510=70
CL9
XNS510
CL12
XNS510
CL12
XNS510
CL9
XNS510
CL9
XNS510
MTGN
External turning
Shim Screw
S34
Chipbreaker
CBT3

Work Material

Finish
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB 280HB)
Light
FY
SY
Grade
Cutting Speed
(SFM)
NX3035
850 1210
NX3035
770 1100
Medium
MS
UE6110
850 1440
Finish
FH
NX3035
655 935
Light
SA
UE6110
685 1160
Medium
MA
UE6110
620 1065
Work Material
M
Stainless Steel
( < 200HB)
K
Cast Iron
( < 350MPa)
Grade
Cutting Speed
(SFM)
Finish
FH
US735
345 655
Light
SA
US735
310 605
Medium
MS
US735
275 540
Light
MA
UC5115
520 965
Medium
Standard
UC5115
520 965
Semi-Heavy Flat Top
UC5115
505 915
MTGN type inserts
A085A091, A100
SPARE PARTS
M001
CBN & PCD inserts
B030, B031, B037, B055
TECHNICAL DATA
N001
C019
ii INSERTS
TN TOOL HOLDERS
MTAN
Multiple Clamp Type

M Holder
90
L2
90
H2
Order Number
Insert Number
-103X
a r
-123X
a r
-163X
a a
-164
-165
-204
-205
-246
-864
*
*
H1
a a
a
a a
TNMA
TNMG
TNMM
TNGA
TNGG
a
r
r
.625
22p
Right hand tool

holder shown.
-164
*
*
r r
r r
(3,4,5,6)
(3,4)
(3)
*3
H2
F1
Shim
.875
.625
.625
4.500 1.000
.625
4.500 1.000
.750
*1 NL34L
.625 ITSN323
*1 NL34L
.750 ITSN323
.625 4.500

NL23
*
6.000 1.000 1.000 1.000 ITSN323
*
6.000 1.218 1.000 1.000 ITSN432
XNS36
CL6
XNS36
CL6
XNS36
CL6
XNS36
NL46
CL9
XNS59
NL58
CL9
XNS510
CL9
XNS59
CL9
XNS510
CL12
XNS510
CL9
XNS59
43p *
54p *
66p *
43p *
*1 NL46
1.250 1.250 7.000 1.218 1.250 1.250 ITSN432
*1 NL58
1.250 1.250 7.000 1.375 1.250 1.250 ITSN533
*1 NL68L
1.500 1.500 7.000 1.484 1.500 1.500 ITSN636
*1 NL46
1.500 1.000 7.000 1.218 1.500 1.000 ITSN432
CL19
NL34L
*
1.000 1.000 6.000 1.375 1.000 1.000 ITSN533
Shim Screw
S34
Multiple Clamp Type

M Holder
Finish
Chipbreaker
CBT3
Light
FH
SA
Medium
MA
Medium
MH
F1
MTRNR/L -123X
(3,4)
MS
75
L2
H1
(3)
(3,4)
(3,4)
Medium to
Semi-Heavy
Stainless
CBN
GH
L1
Right hand tool

holder shown.
(3,4)
MS
(3,4)
(3,4)
(3)
*3
Dimensions (inch)
Insert Number
R L
H1
TNMA
TNMG
TNMM
TNGA
TNGG
(3,4)
CBN
54p *
H2
Order Number
(3,4)
Stainless
Stock
Medium
MH
(3)
L2
L1
1
33p **2 .625 .625
1
33p **2 .750 .750
1
33p **2 1.000 1.000
1
43p * 1.000 1.000
External turning
75
Medium
MA
Medium to
Semi-Heavy
GH

MTRN
Light
SA
Dimensions (inch)
R L
MTANR/L-102
L1
H1
Stock
Finish
FH
F1
External turning
L1
L2
H2
F1
Shim
*1 NL34L
33p **
.750 .750 4.500 1.203 .750 .897 ITSN323
1
*1 NL46
43p * 1.000 1.000 6.000 1.250 1.000 1.040 ITSN432
1
2

CL20
XNS46
CL9
XNS510
Shim Screw
S34
Chipbreaker
CBT3
C020
MTAN type inserts
A085A091, A100
MTRN type inserts
A085A091, A100
CBN & PCD inserts
B030, B031, B037, B055
Multiple Clamp Type

M Holder
Finish
Light
FH
SA
Medium
MA
Medium
MH
F1
External turning
Chamfering
60
L2
L1
(3)
(3,4)
(3,4)
Medium to
Semi-Heavy
Stainless
CBN
GH
(3,4)
MS
H2
H1
730
(3,4,5)
Order Number
Stock
Insert Number
22p
-103X
33p *
.625
-123X
33p *
.750
-164
-205
-854
-864
-865
*
*
TNMA
TNMG
TNMM
TNGA
TNGG
(3)
*2
Dimensions (inch)
H1
MTENN-82
(3,4)
.500
L1
L2
H2
.500 4.500 1.000
Shim
F1
.500 .250
.625 4.500 1.156
.625 .313
*
ITSN323
.750 4.500 1.156
.750 .375
*
ITSN323
1
1
1
*
ITSN432
NL23
CL6
XNS36
NL34L
CL6
XNS36
NL34L
CL6
XNS36
NL46
CL9
XNS59
CL9
XNS510
CL9
XNS59
CL9
XNS59
CL9
XNS510
43p *
1.000 1.000 6.000 1.500 1.000 .500
54p *
43p *
43p *
54p *
*1 NL58
1.250 1.250 7.000 1.620 1.250 .625 ITSN533
*1 NL46
1.250 1.000 6.000 1.500 1.250 .500 ITSN432
*1 NL46
1.500 1.000 7.000 1.500 1.500 .500 ITSN432
*1 NL58
1.500 1.000 7.000 1.620 1.500 .500 ITSN533
MTEN

MTCN
Multiple Clamp Type

M Holder
Finish
FH
Light
SA
Medium
MA
Medium
MH
Facing
90
L2
L1
(3)
(3,4)
(3,4)
Medium to
Semi-Heavy
Stainless
CBN
GH
(3,4)
MS
H2
H1
730
(3,4)
Order Number
Stock
Insert Number
-124
-443X
-644
-664
*
*
TNMA
TNMG
TNMM
TNGA
TNGG
33p **
1
2
43p *
33p **
1
2
43p *
.500
L1
L2
1.125
H2

1
*
ITSN323
.750
.750
1.000
.500
1.000
.750
*1
4.500 1.375
.750 ITSN432
*1
8.000 1.125 1.000 ITSN323
*1
8.000 1.375 1.000 ITSN432
.750
*1
8.000 1.375 1.500 ITSN432
.500
Shim
4.500

NL34L
CL7
XNS36
NL46
CL12
XNS59
NL34L
CL7
XNS36
NL46
CL12
XNS59
NL46
CL12
XNS59
Shim Screw
S34
Chipbreaker
CBT3

Work Material
*3
.500
1
43p * 1.500
(3)
Dimensions (inch)
H1
MTCNN-83X
(3,4)
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB 280HB)

Finish
Light
Medium
Finish
Light
Medium
FY
SY
Grade
NX3035
NX3035
MS
UE6110
FH
NX3035
SA
MA
UE6110
UE6110
Cutting Speed
(SFM)
Work Material
850 1210
770 1100
850 1440
655 935
685 1160
620 1065
Stainless Steel
( < 200HB)
Cast Iron
( < 350MPa)
Grade
FH
Finish
SA
Light
MS
Medium
MA
Light
Standard
Medium
Semi-Heavy Flat Top
US735
US735
US735
Cutting Speed
(SFM)
UC5115
UC5115
UC5115
345 655
310 605
275 540
520 965
520 965
505 915
MTEN type inserts
A085A091
MTCN type inserts
A085A091, A100
SPARE PARTS
M001
CBN & PCD inserts
B030, B031, B037, B055
TECHNICAL DATA
N001
C021
ii INSERTS
TN TOOL HOLDERS
DTFN
DOUBLE CLAMP Type
Facing
Finish
FH
91
(3)
(3)
Stainless
CBN
Insert Number
DTFNR/L -123
a a
-163
a a
-164
a a
-204
a a
H1
(3)
(3)
(3)
*2
L1
L2
H2
F1
Shim
.750 1.000
LLSTN32
*1) LLP23 DCK2211 DCS2 DC0520T TKY15F
(LLSTN33
33p
1.000 1.000 6.000 1.000 1.000 1.250
LLSTN32
(LLSTN33
43p
43p
.750
33p
TNMA
TNMG
TNMM
TNGA
TNGG
(3)
MS
Dimensions (inch)
R L
Medium
MH
(3)
Right hand tool

holder shown.
Order Number
Medium
MA
Medium to
Semi-Heavy
GH
Stock
Light
SA
.750 4.500 1.000
*12 Please
* Clamp Torque (lbf-in) : DC0520T=31, DC0621T=44
DTCN
DOUBLE CLAMP Type
90
Finish
FH
L2
90
L1
(3)
(3)
Stainless
CBN
H1
H2
- 443
TNMA
TNMG
TNMM
TNGA
TNGG
(3)
MS
(3)
H1
L1
L2
33p
.750
.500
4.500 1.375
33p
1.000
.500
(3)
*2
Dimensions (inch)
Stock Insert Number
Medium
MH
(3)
(3)
DTCNN- 433
Medium
MA
Medium to
Semi-Heavy
GH
Order Number
Light
SA
F1
Facing
Shim
H2
F1
.750
.539
LLSTN32
(LLSTN33
6.000 1.375 1.000
.539
LLSTN32
(LLSTN33)
*12 Please
*
C022
a
r
DTFN type inserts
A085A091
DTCN type inserts
A085A091
CBN & PCD inserts
B030, B031, B055
L1
Insert Number
H1
22p
r r
-103X
r r
-123BX
a a
-163CX
a a
-163DX
-164C
r r
r r
-164D
a a
-165C
TNMA
TNMG
TNMM
TNGA
TNGG
r r
43p *
a r
1
54p *
-246D
r r
1
66p *
-246E
r r
66p *
-855D
r r
-204D
-205D
.500
54p *
r r
Right hand tool

holder shown.
(3,4)
(3,4)
Stainless
CBN
(3,4)
MS
(3,4)
(3,4,5,6)
(3)
*3
L1
.500 4.500
L2
H2
F1
Shim
.813
.500
.750
1
33p **2 .625 .625 4.500 .875 .625
1
33p **2 .750 .750 4.500 .875 .750
1
33p **2 1.000 1.000 5.000 .875 1.000
1
33p **2 1.000 1.000 6.000 .875 1.000
1
43p * 1.000 1.000 5.000 1.218 1.000
1
43p * 1.000 1.000 6.000 1.218 1.000
1
54p * 1.000 1.000 5.000 1.375 1.000
1
-165D
(3)
Dimensions (inch)
R L
MTFNR/L -82
Medium
MH
Medium to
Semi-Heavy
GH
H1
H2
Order Number
Medium
MA
90
L2
Stock
Light
SA
F1
90
Finish
FH

NL23
*1 NL34L
.875 ITSN323
*1 NL34L
1.000 ITSN323
1
*
1.250 ITSN323
*
1.250 ITSN323
*
1.250 ITSN432
XNS36
CL6
XNS36
CL6
XNS36
NL34L
CL6
XNS36
NL34L
CL6
XNS36
NL46
CL9
XNS510
CL9
XNS510
CL12
XNS510
CL12
XNS510
CL9
XNS510
CL12
XNS510
CL12
XNS510
CL12
XNS510
CL12
XNS510
*1 NL46
1.250 ITSN432
*1 NL58
1.250 ITSN533
*1 NL58
1.000 1.000 6.000 1.375 1.000 1.250 ITSN533
*1 NL46
1.250 1.250 6.000 1.218 1.250 1.500 ITSN432
*1 NL58
1.250 1.250 6.000 1.375 1.250 1.500 ITSN533
*1 NL68
1.500 1.500 6.000 1.500 1.500 2.000 ITSN636
*1 NL68
1.500 1.500 7.000 1.500 1.500 2.000 ITSN636
1
*1 NL58
54p * 1.250 1.000 6.000 1.375 1.250 1.250 ITSN533
1

*13 (Opt.)
*
CL19
MTFN
Multiple Clamp Type

M Holder
Facing
Shim Screw
S34
Chipbreaker
CBT3

Work Material

Finish
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB 280HB)
Light
FY
SY
Grade
Cutting Speed
(SFM)
NX3035
850 1210
NX3035
770 1100
Medium
MS
UE6110
850 1440
Finish
FH
NX3035
655 935
Light
SA
UE6110
685 1160
Medium
MA
UE6110
620 1065
Work Material
Grade
Cutting Speed
(SFM)
FH
US735
345 655
Light
SA
US735
310 605
Medium
MS
US735
275 540
Light
MA
UC5115
520 965
Medium
Standard
UC5115
520 965
Semi-Heavy Flat Top
UC5115
505 915

Finish
Stainless Steel
( < 200HB)
K
Cast Iron
( < 350MPa)
MTFN type inserts
A085A091, A100
SPARE PARTS
M001
CBN & PCD inserts
B030, B031, B037, B055
TECHNICAL DATA
N001
C023
ii INSERTS
VN TOOL HOLDERS
DVJN
DOUBLE CLAMP Type
F1
93
L2
Medium
MA
Medium
MH
(3)
(3)
(3)
(3)
Medium
Stainless
G Class
CBN
Standard
L1
Order Number
Stock
MS
MJ
DVJNR/L-123
a a
-163
a a
-203
a a
H1
H1
VNGA
VNMG
VNGM
VNGG
VNMM
33p
Right hand tool

holder shown.
(3)
(3)
(3)
.750
L1
L2
H2
.750 4.500 1.625
(3)
Dimensions (inch)
Insert Number
R L
Shim
F1
.750 1.000 DCSVN32 LLP13 DCK3113 DCS2 DC0520T TKY15F
33p
1.000 1.000 6.000 1.625 1.000 1.250 DCSVN32 LLP13 DCK3113 DCS2 DC0520T TKY15F
33p
MVJN
Multiple Clamp Type

M Holder
External turning
Copying
F1
93
L2
L1
Order Number
a a
-163C
a a
-163D
a a
-164C
r r
-164D
a a
-203D
r r
-204D
H1
r r
Medium
MA
Medium
MH
(3)
(3)
(3)
(3)
Medium
Stainless
G Class
CBN
Standard
Right hand tool

holder shown.
MJ
MS
(3)
(3)
(3)
(3)
*2
L1
L2
.750 4.500 1.687
H2
F1
Shim

NL34L
CL30
XNS510
33p
1.000 1.000 5.000 1.687 1.000 1.250 IVSN322
NL34L
CL30
XNS510
33p
1.000 1.000 6.000 1.687 1.000 1.250 IVSN322
NL34L
CL30
XNS510
NL46
CL30
XNS510
43p
.750
.750 1.000 IVSN322
33p
VNGA
VNMG
VNGM
VNGG
VNMM
Light
SH
Dimensions (inch)
Insert Number
R L
MVJNR/L -123B
H1
H2
93
Stock
Finish
FH
Light
SH
13
H2
93
Finish
FH
External turning
Copying
*
1.000 1.000 5.000 2.000 1.000 1.250 IVSN432
43p
*
1.000 1.000 6.000 2.000 1.000 1.250 IVSN432
NL46
CL30
XNS510
33p
1.250 1.250 6.000 1.687 1.250 1.500 IVSN322
NL34L
CL30
XNS510
43p
*1 NL46
1.250 1.250 6.000 2.000 1.250 1.500 IVSN432
CL30
XNS510

*12 (Opt.)
* Clamp Torque (lbf-in) : XNS510=70
C024
a
r
DVJN type inserts
A092, A093
MVJN type inserts
A092, A093
CBN & PCD inserts
B032, B033, B056
DOUBLE CLAMP Type
-163
Medium
MH
(3)
(3)
(3)
(3)
Stainless
G Class
CBN
MS
MJ
H1
13
Stock
H1
VNGA
a a VNMG
VNGM
a a VNGG
VNMM
33p
33p
Right hand tool

holder shown.
(3)
(3)
(3)
.750
L1
L2
H2
.750 4.500 1.250
(3)
Dimensions (inch)
Insert Number
R L
DVPNR/L-123
Medium
MA
Medium
Standard
L1
H2
Order Number
Light
SH
Shim
F1
.750 1.000 DCSVN32 LLP13 DCK3113 DCS2 DC0520T TKY15F
DOUBLE CLAMP Type
External turning
Copying
7230
L2
72
30
Finish
FH
Light
Medium
MH
L1
(3)
(3)
(3)
(3)
Medium
Stainless
G Class
CBN
Standard
MJ
MS
H2
H1
16
(3)
(3)
Order Number
Medium
MA
SH
F1
DVVN
11730
L2
117
30
Finish
FH
Facing
Copying
F1
DVPN
H1
DVVNN-123
-163
33p
33p
.750
L1
L2
H2
.750 4.500 1.750
(3)
Dimensions (inch)
Stock Insert Number

VNGA
VNMG
VNGM
VNGG
VNMM
(3)
Shim
F1
.750
.375 DCSVN32 LLP13 DCK3113 DCS2 DC0520T TKY15F
1.000 1.000 6.000 1.750 1.000
.500 DCSVN32 LLP13 DCK3113 DCS2 DC0520T TKY15F

Work Material
P
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB 280HB)
Grade
Cutting Speed
(SFM)
Work Material
Finish
FY
NX3035
850 1210
Steel
M Stainless
( < 200HB)
Light
SY
NX3035
770 1100
Medium
MS
UE6110
850 1440
Finish
FH
NX3035
655 935
Light
SH
UE6110
685 1160
Medium
MA
UE6110
620 1065
Cast Iron
( < 350MPa)
Grade
Cutting Speed
(SFM)
MS
US735
275 540
Light
MA
UC5115
520 965
Medium
Standard
UC5115
520 965
Semi-Heavy Flat Top
UC5115
505 915

Medium
DVPN type inserts
A092, A093
DVVN type inserts
A092, A093
SPARE PARTS
M001
CBN & PCD inserts
B032, B033, B056
TECHNICAL DATA
N001
C025
ii INSERTS
VN TOOL HOLDERS
MVLN
Multiple Clamp Type

M Holder
Facing
F1
95
(4)
95
L2
Medium
MJ
L1
H1
H2
730
Stock
Order Number
Insert Number
R L
MVLNR/L -164C
H1
43p
a a
-164D
a a
-204D
a a
-244D
VNGA
VNMG
VNGM
43p
43p
43p
*2
Dimensions (inch)
B
L1
L2
H2
F1
Shim
*1
1.000 1.000 5.000 1.500 1.000 1.750 IVSN432
*1
1.000 1.000 6.000 1.500 1.000 1.750 IVSN432
*1
1.250 1.250 6.000 1.500 1.250 2.000 IVSN432
*1
1.500 1.500 6.000 1.500 1.500 2.250 IVSN432
NL46
CL12
XNS510
NL46
CL12
XNS510
NL46
CL12
XNS510
NL46
CL12
XNS510

*12 (Opt.)
Clamp Torque (lbf-in) : XNS510=70
*

Work Material

Finish
Mild Steel
( < 180HB)
Carbon Steel
Alloy Steel
(180HB 280HB)
Light
FY
SY
Grade
Cutting Speed
(SFM)
NX3035
850 1210
NX3035
770 1100
Medium
MS
UE6110
850 1440
Finish
FH
NX3035
655 935
Light
SA
UE6110
685 1160
Medium
MA
UE6110
620 1065
Work Material
Grade
Cutting Speed
(SFM)
FH
US735
345 655
Light
SA
US735
310 605
Medium
MS
US735
275 540
Light
MA
UC5115
520 965
Medium
Standard
UC5115
520 965
Semi-Heavy Flat Top
UC5115
505 915

Finish
Stainless Steel
( < 200HB)
K
Cast Iron
( < 350MPa)
C026
: Inventory maintained. r : Non stock, produced to order only.
MVLN type inserts
A093
ii INSERTS
WN TOOL HOLDERS
Finish
Light
SA
Medium
MA
Medium
MH
F1
FH
95
L2
L1
(4)
(4)
(3,4)
Medium
Medium to
Semi-Heavy
Stainless
Standard
GH
(4)
MS
Stock
Order Number
a a
-124
a a
-163
a a
Insert Number
-164
-204
H1
WNMA
WNMG
Right hand tool

holder shown.
(4)
(4)
(3,4)
*2
Dimensions (inch)
R L
DWLNR/L-123
H1
H2
95
L1
L2
H2
Shim
F1
LLSWN32
33p
.750
.750 4.500 1.000
.750 1.000
43p
.750
.750 4.500 1.250
.750 1.000 LLSWN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
(LLSWN33)
LLSWN32
33p
1.000 1.000 6.000 1.000 1.000 1.250
a a
43p
1.000 1.000 6.000 1.250 1.000 1.250 LLSWN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
a a
43p
1.250 1.250 6.000 1.250 1.250 1.500 LLSWN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
DWLN
DOUBLE CLAMP Type
External turning
Facing
(LLSWN33)
use shim no.LLSWN33 with .125inch thick insert. When using .125inch thick inserts, the shim should be ordered separately.
*12 Please
*
Multiple Clamp Type

M Holder
95
L2
5
Order Number
Stock
Light
SA
Medium
MA
Medium
MH
L1
(4)
(4)
(3,4)
Medium
Medium to
Semi-Heavy
Stainless
Standard
GH
(4)
MS
5
H1
H2
95
Finish
FH
External turning
Facing
F1
MWLN
(4)
(4)
(3,4)
Dimensions (inch)
Insert Number
R L
Right hand tool

holder shown.
H1
L1
L2
H2
F1
Shim
MWLNR/L -1232
a a
32p
.750
.750 4.500 1.000
.750 1.000 IWSN322 NL34L
CL7
XNS36
-1233
a a
33p
.750
.750 4.500 1.000
.750 1.000 IWSN322 NL34L
CL7
XNS36
-124B
a a
43p
.750
.750 4.500 1.000
.750 1.000 IWSN432 NL46
CL20
XNS48
-1632
a a
32p
1.000 1.000 6.000 1.188 1.000 1.250 IWSN322 NL34
CL7
XNS36
-1633
a a
33p
1.000 1.000 6.000 1.188 1.000 1.250 IWSN322 NL34L
CL7
XNS36
-164D
a a
43p
1.000 1.000 6.000 1.188 1.000 1.250 IWSN432 NL46
CL20
XNS48
-854D
a a
43p
1.250 1.000 6.000 1.188 1.250 1.250 IWSN432 NL46
CL20
XNS48
-204D
a a
43p
1.250 1.250 6.000 1.188 1.250 1.500 IWSN432 NL46
CL20
XNS48
-165D
a a
54p
1.000 1.000 6.000 1.188 1.000 1.250 IWSN533 NL34L
CL9
XNS59
-205D
a a
54p
1.250 1.250 6.000 1.125 1.250 1.500 IWSN533 NL34L
CL9
XNS59
-245E
a a
54p
1.500 1.500 7.000 1.125 1.500 2.000 IWSN533 NL58
CL9
XNS59
WNMA
WNMG
* Clamp Torque (lbf-in) : XNS36=30, XNS48=45, XNS59=70

DWLN type inserts
A094A097
MWLN type inserts
A094A097
SPARE PARTS
M001
CBN inserts
B034
TECHNICAL DATA
N001
C027
i i INSERTS
VB TOOL HOLDERS
SVJB
Screw Clamp Type

SP Holder
External turning
Copying
Finish
FV
(2)
(3)
Medium
Medium
MV
93
MJ
Right hand tool

holder shown.
Order Number
Stock
R L
SVJBR/L-062
a a
-082
a a
-102
a a
-123
a a
-163
a a
H1
VBGT
VBMT
VBET
(2)
L1
(3)
Dimensions (inch)
Insert Number
Finish
FJ
L2
H2
F1
Clamp Screw
Wrench
22p
.375
.375
2.500
.875
.375
.500
TS25
TKY08F
22p
.500
.500
3.500
.875
.500
.625
TS25
TKY08F
22p
.625
.625
4.000
.875
.625
.750
TS25
TKY08F
33p
.750
.750
4.500
1.250
.750
1.000
TS4
TKY15F
33p
1.000
1.000
6.000
1.250
1.000
1.250
TS4
TKY15F
* Clamp Torque (lbf-in) : TS25=8.9, TS4=31
SVVB
Screw Clamp Type

SP Holder
External turning
Copying
72
30
Finish
FV
(2)
(3)
Medium
Medium
MV
MJ
(2)
Order Number
Stock
SVVBN -062
-082
VBGT
VBMT
VBET
(3)
Dimensions (inch)
Insert Number
Finish
FJ
H1
L1
H2
F1
Clamp Screw
Wrench
22p
.375
.375
2.500
.375
.188
TS25
TKY08F
22p
.500
.500
3.000
.500
.250
TS25
TKY08F
22p
.625
.625
4.000
.625
.313
TS25
TKY08F
22p
-102
-122
.750
.750
4.500
.750
.375
TS25
TKY08F
-123
33p
.750
.750
4.500
.750
.375
TS4
TKY15F
-163
33p
1.000
1.000
6.000
1.000
.500
TS4
TKY15F
C028
SVJB type inserts
A125A127
SVVB type inserts
A125A127
CBN & PCD inserts
B047, B063
Finish
FV
17
30
(2)
(3)
Medium
Medium
MV
Order Number
Stock
R L
SVHBR/L -062
a a
-082
a a
-102
a a
-123
a a
-163
a a
H1
VBGT
VBMT
VBET
MJ
(2)
(3)
Dimensions (inch)
Insert Number
Finish
FJ
L1
L2
H2
F1
Clamp Screw
Wrench
22p
.375
.375
2.500
.600
.375
.500
TS25
TKY08F
22p
.500
.500
3.500
.600
.500
.625
TS25
TKY08F
22p
.625
.625
4.000
.600
.625
.750
TS25
TKY08F
33p
.750
.750
4.500
1.000
.750
1.000
TS4
TKY15F
33p
1.000
1.000
6.000
1.000
1.000
1.250
TS4
TKY15F
SVHB
Screw Clamp Type

SP Holder
Facing

Work Material
Hardness
Cutting Mode
Breaker
Grade
Cutting Speed
(SFM)
Finish Cutting
FV
NX2525
755 1080
Light Cutting
Standard
UE6110
605 1015
Finish Cutting
FV
NX2525
555 800
Light Cutting
Standard
UE6110
510 870
Mild Steel
< 180HB
Carbon Steel, Alloy Steel
180HB 280HB
Stainless Steel
< 200HB
Medium Cutting
Standard
US735
230 460
Cast Iron
Tensile Strength < 350MPa
Medium Cutting
MV
VP15TF
330 490
SVHB type inserts
A125A127
SPARE PARTS
M001
CBN & PCD inserts
B047, B063
TECHNICAL DATA
N001
C029
ii INSERTS
CC TOOL HOLDERS
SCLC
Screw Clamp Type

SP Holder
External turning
Facing
Finish
Medium
FV
Standard
(2,3)
(2,3,4)
Flat Top
CBN/PCD
95
Order Number
Stock
SCLCR/L -062
a a
-083
a a
-104
a a
-124
a a
-164
a a
z
x
H1
CCET
CCGT
CCMT
CCMW
CCGW
CCMH
(2,3,4)
Dimensions (inch)
Insert Number
R L
(2,3,4)
L1
L2
H2
F1
Shim
Shim Screw Clamp Screw
Wrench
21.5p
.375
.375 2.500
.350
.375
.500
TS25
zTKY08F
32.5p
.500
.500 3.500
.540
.500
.625
TS43
zTKY15F
43p
.625
.625 4.000
.660
.625
.750
TS5
zTKY25F
.750
.875 SPSCN42
JSS7
TS53
xTKY25R
1.000 1.000 6.000 1.000 1.000 1.250 SPSCN42
JSS7
TS53
xTKY25R
43p
43p
.750
.750 4.500
.660
* Clamp Torque (lbf-in) : TS25=8.9, TS43=31, TS5=66, TS53=66
C030
SCLC type inserts
A101A106
CBN & PCD inserts
B038B040, B058
ii INSERTS
DC TOOL HOLDERS
External turning
Copying
Screw Clamp Type

SP Holder
Finish
FV
Finish
Light
R/L-F
Medium
SV
MV
(2,3)
(2,3)
(2,3)
Medium
Flat Top
CBN/PCD
(2,3)
(2,3)
(2,3)
Standard
93
Order Number
Stock
SDJCR/L-062
a a
-083
a a
-103
a a
-123
a a
-163
a a
z
x
H1
DCET
DCGT
DCMT
DCMW
Dimensions (inch)
Insert Number
R L
(2,3)
L1
L2
H2
F1
Shim
Wrench
21.5p
.375
.375 2.500
.500
.375
.500
TS25
zTKY08F
32.5p
.500
.500 3.500
.700
.500
.625
TS43
zTKY15F
32.5p
.625
.625 4.000
.700
.625
.750
TS43
zTKY15F
32.5p
.750
.750 4.500
.700
.750
.875 SPSDN32 JSS6
TS406
xTKY15R
1.000 1.000 6.000 1.000 1.000 1.250 SPSDN32 JSS6
TS406
xTKY15R
32.5p
SDJC
* Clamp Torque (lbf-in) : TS25=8.9, TS43=31, TS406=31
SDNC
External turning
Copying
Screw Clamp Type

SP Holder
Finish
FV
Finish
Light
R/L-F
Medium
SV
MV
(2,3)
(2,3)
(2,3)
Medium
Flat Top
CBN/PCD
(2,3)
(2,3)
(2,3)
Standard
62
30
(2,3)
Order Number
Stock
SDNCN -062
-083
-103
-123
-163
Insert Number
DCET
DCGT
DCMT
DCMW
Dimensions (inch)
z
x
H1
L1
H2
F1
Shim
Wrench
21.5p
.375
.375
2.500
.375
.188
TS25
zTKY08F
32.5p
.500
.500
3.500
.500
.250
TS43
zTKY15F
32.5p
.625
.625
4.000
.625
.313
TS43
zTKY15F
32.5p
.750
.750
4.500
.750
.375
SPSDN32 JSS6
TS406
xTKY15R
32.5p
1.000
1.000
6.000
1.000
.500
SPSDN32 JSS6
TS406
xTKY15R
* Clamp Torque (lbf-in) : TS25=8.9, TS43=31, TS406=31

Work Material
Hardness
Cutting Mode
Breaker
Grade
Cutting Speed
(SFM)
Finish Cutting
FV
NX3035
720 1030
Light Cutting
Standard
UE6110
705 1180
Finish Cutting
FV
NX3035
540 770
Light Cutting
Standard
UE6110
525 885
Mild Steel
< 180HB
180HB 280HB
Stainless Steel
< 200HB
Medium Cutting
Standard
US735
230 460
Cast Iron
Medium Cutting
Flat Top
UC5115
425 790
SDJC type inserts
A109A113
SDNC type inserts
A109A113
SPARE PARTS
M001
CBN & PCD inserts
B042, B043, B059
TECHNICAL DATA
N001
C031
ii INSERTS
DC TOOL HOLDERS
SDXC
Screw Clamp Type

SP Holder
External turning
Copying
Finish
FV
Finish
R/L-F
Light
SV
Medium
MV
(2,3)
(2,3)
(2,3)
Medium
Flat Top
CBN/PCD
(2,3)
(2,3)
(2,3)
Standard
Order Number
Stock
SDXCR/L -062
a a
-082
a a
-103
a a
DCET
DCGT
DCMT
DCMW
Dimensions (inch)
Insert Number
R L
(2,3)
Clamp Screw Wrench
H1
L1
H2
F1
21.5p
.375
.375
2.500
.375
.625
TS25
TKY08F
21.5p
.500
.500
3.500
.500
.750
TS25
TKY08F
32.5p
.625
.625
4.000
.625
1.000
TS43
TKY15F
Clamp Torque (lbf-in) : TS25=8.9, TS43=31
C032
SDXC type inserts
A109A113
CBN & PCD inserts
B042, B043, B059
ii INSERTS
RC TOOL HOLDERS
SRGC
Screw Clamp Type

SP Holder
External turning
Copying
Medium
Standard
Order Number
Stock
R L
SRGCR/L -0608M
a a
-0808M
a a
-1008M
a a
RCMT
Dimensions (inch)
Insert Number
Clamp Screw Wrench
H1
L1
L2
H2
F1
0803M0
.375
.375
2.500
.610
.375
.625
TS3
TKY08F
0803M0
.500
.500
3.500
.610
.500
.750
TS3
TKY08F
0803M0
.625
.625
4.000
.610
.625
.875
TS3
TKY08F
(08)
Clamp Torque (lbf-in) : TS3=8.9
SRDC
Screw Clamp Type

SP Holder
External turning
Copying
Medium
Standard
(08)
Order Number
Stock
SRDCN -0608M
-0808M
-1008M
RCMT
Dimensions (inch)
Insert Number
Clamp Screw Wrench
H1
L1
L3
H2
F1
0803M0
.375
.375
2.500
.375
.375
.188
TS3
TKY08F
0803M0
.500
.500
3.500
.500
.500
.250
TS3
TKY08F
0803M0
.625
.625
4.000
.500
.625
.313
TS3
TKY08F

Work Material
Hardness
Cutting Mode
Breaker
Grade
Cutting Speed
(SFM)
Finish Cutting
FV
NX3035
720 1030
Light Cutting
Standard
UE6110
705 1180
Finish Cutting
FV
NX3035
540 770
Light Cutting
Standard
UE6110
525 885
Mild Steel
< 180HB
180HB 280HB
Stainless Steel
< 200HB
Medium Cutting
Standard
US735
230 460
Cast Iron
Medium Cutting
Flat Top
UC5115
425 790
SRGC type inserts
A115
SPARE PARTS
M001
SRDC type inserts
A115
TECHNICAL DATA
N001
C033
ii INSERTS
SC TOOL HOLDERS
SSBC
Screw Clamp Type

SP Holder
External turning
Finish
Medium
FV
Standard
(3)
(3,4)
Flat Top
75
(3,4)
Order Number
Stock
Insert Number
R L
SSBCR/L -103
-124
a a
-164
a a
SCMT
SCMW
z
x
H1
a a
Dimensions (inch)
B
L1
H2
F1
Shim
32.5p
.625
.625
4.000
.625
.500
43p
.750
.750
4.500
.750
.625
43p
1.000
1.000
6.000
1.000
.875
Wrench
TS43
zTKY15F
SPSSN42 JSS7
TS53
xTKY25R
SPSSN42 JSS7
TS53
xTKY25R
Clamp Torque (lbf-in) : TS43=31, TS53=66
SSSC
Screw Clamp Type

SP Holder
External turning
Facing, Chamfering
Finish
Medium
FV
Standard
(3)
(3,4)
Flat Top
45
Order Number
Stock
SSSCR/L -083
a a
-103
a a
-124
a a
-164
a a
z
x
H1
SCMT
SCMW
Dimensions (inch)
Insert Number
R L
(3,4)
L1
L2
H2
F1
Shim
Shim Screw Clamp Screw Wrench
32.5p
.500
.500 3.500
.625
.500
.550
TS43
zTKY15F
32.5p
.625
.625 4.000
.625
.625
.680
TS43
zTKY15F
43p
.750
.750 4.500 1.000
.750
.850 SPSSN42 JSS7
TS53
xTKY25R
1.000 1.000 6.000 1.000 1.000 1.110 SPSSN42 JSS7
TS53
xTKY25R
43p
Clamp Torque (lbf-in) : TS43=31, TS53=66
C034
SSBC type inserts
A117
SSSC type inserts
A117
ii INSERTS
TC TOOL HOLDERS
Finish
Medium
FV
Standard
(2,3)
(2,3)
Flat Top
CBN/PCD
91
(2,3)
Stock
Order Number
STGCR/L -062
-082.5
a a
-103
a a
-123
a a
-163
a a
H1
a a
TCGT
TCMT
TCMW
Dimensions (inch)
Insert Number
R L
(2,3)
z
L1
L2
H2
F1
Shim
Wrench
21.5p
.375
.375 2.500
.550
.375
.500
TS25
zTKY08F
2.52p
.500
.500 3.500
.700
.500
.625
TS3
zTKY08F
32.5p
.625
.625 4.000
.800
.625
.750
TS43
zTKY15F
.750
.875 SPSTN32
JSS6
TS406 xTKY15R
1.000 1.250 SPSTN32
JSS6
TS406 xTKY15R
32.5p
32.5p
.750 4.500
.800
1.000 1.000 6.000
.750
.900
STGC
Screw Clamp Type

SP Holder
External turning
* Clamp Torque (lbf-in) : TS25=8.9, TS3=8.9, TS43=31, TS406=31
STFC
Screw Clamp Type

SP Holder
Facing
Finish
Medium
FV
Standard
91
Order Number
Stock
STFCR/L -062
-082.5
a a
-102.5
a a
-123
a a
-163
a a
TCGT
TCMT
TCMW
(2,3)
(2,3)
z
x
H1
a a
(2,3)
CBN/PCD
Dimensions (inch)
Insert Number
R L
(2,3)
Flat Top
L1
L2
H2
F1
Shim
Wrench
21.5p
.375
.375 2.500
.500
.375
.500
TS25
zTKY08F
2.52p
.500
.500 3.500
.571
.500
.625
TS3
zTKY08F
2.52p
.625
.625 4.000
.571
.625
.750
TS3
zTKY08F
32.5p
.750
.750 4.500
.866
.750
.875 SPSTN32
JSS6
TS406 xTKY15R
1.000 1.000 6.000
.866
1.000 1.250 SPSTN32
JSS6
TS406 xTKY15R
32.5p
* Clamp Torque (lbf-in) : TS25=8.9, TS3=8.9, TS406=31

Work Material
Hardness
Cutting Mode
Breaker
Grade
Cutting Speed
(SFM)
Finish Cutting
FV
NX3035
720 1030
Light Cutting
Standard
UE6110
705 1180
Finish Cutting
FV
NX3035
540 770
Light Cutting
Standard
UE6110
525 885
Mild Steel
< 180HB
180HB 280HB
Stainless Steel
< 200HB
Medium Cutting
Standard
US735
230 460
Cast Iron
Medium Cutting
Flat Top
UC5115
425 790
STGC type inserts
A119, A120
STFC type inserts
A119, A120
SPARE PARTS
M001
CBN & PCD inserts
B044, B060
TECHNICAL DATA
N001
C035
ii INSERTS
VC TOOL HOLDERS
SVPC
Screw Clamp Type

SP Holder
External turning
Copying
Finish
Medium
FV
Standard
(3)
(2,3)
Flat Top
117
30
(2,3)
Order Number
Stock
Insert Number
a a
-102
a a
-123
a a
-163
a a
H1
VCMT
VCGT
VCMW
NP-VCGW
z
x
R L
SVPCR/L -082
Dimensions (inch)
B
L1
L2
H2
F1
Shim
Shim Pin Clamp Screw Wrench
22p
.500
.500 3.500 1.000
.500
.750
TS25
zTKY08F
22p
.625
.625 4.000 1.000
.625
.875
TS25
zTKY08F
.750
.750 4.500 1.206
.750 1.000 SPSVN32 BCP141
TS44
xTKY15R
1.000 1.000 6.000 1.206 1.000 1.250 SPSVN32 BCP141
TS44
xTKY15R
33p
33p
SVJC
Screw Clamp Type

SP Holder
External turning
Copying
Finish
Medium
FV
Standard
(3)
(2,3)
Flat Top
93
Order Number
Stock
a a
-083
a a
Insert Number
-103
a a
-123
a a
-163
a a
z
x
H1
VCMT
VCGT
VCMW
NP-VCGW
Dimensions (inch)
R L
SVJCR/L-062
(2,3)
L1
L2
H2
F1
Shim
Shim Pin Clamp Screw Wrench
22p
.375
.375 2.500
.750
.375
.500
TS25
zTKY08F
33p
.500
.500 3.500 1.000
.500
.625
TS43
zTKY15F
33p
.625
.625 4.000 1.000
.625
.750
TS43
zTKY15F
33p
.750
.750 4.500 1.000
.750
.875 SPSVN32 BCP141
TS44
xTKY15R
1.000 1.000 6.000 1.500 1.000 1.250 SPSVN32 BCP141
TS44
xTKY15R
33p
Clamp Torque (lbf-in) : TS25=8.9, TS43=31, TS44=31
C036
SVPC type inserts
A128, A129
SVJC type inserts
A128, A129
CBN & PCD inserts
B048, B063
ii INSERTS
WC TOOL HOLDERS
SWLC
Screw Clamp Type

SP Holder
External turning
Facing
Finish
FJ
Medium
MJ
(2,3)
(2,3)
Standard
95
Order Number
Stock
Dimensions (inch)
Insert Number
R L
(2,3)
Clamp Screw Wrench
H1
L1
L2
H2
F1
21.5p
.313
.313
2.500
.500
.313
.375
TS25
TKY08F
21.5p
.375
.375
2.500
.500
.375
.500
TS25
TKY08F
21.5p
SWLCR/L -052
a a
-062
a a
-082
a a
.500
.500
3.500
.500
.500
.625
TS25
TKY08F
-103
a a
32.5p
.625
.625
4.000
.625
.625
.750
TS4
TKY15F
-123
a a
32.5p
.750
.750
4.500
.625
.750
1.000
TS4
TKY15F
WCGT
WCMT
Medium

Work Material
Hardness
Cutting Mode
Breaker
Grade
Cutting Speed
(SFM)
Finish Cutting
FV
NX3035
720 1030
Light Cutting
Standard
UE6110
705 1180
Finish Cutting
FV
NX3035
540 770
Light Cutting
Standard
UE6110
525 885
Mild Steel
< 180HB
180HB 280HB
Stainless Steel
< 200HB
Medium Cutting
Standard
US735
230 460
Cast Iron
Medium Cutting
Flat Top
UC5115
425 790
SWLC type inserts
A133, A134
SPARE PARTS
M001
CBN & PCD inserts
B049, B064
TECHNICAL DATA
N001
C037
ii INSERTS
XC TOOL HOLDERS
SXZC
DOUBLE CLAMP Type

F1
< 300
( 2)
9230
L2
H2
L1
H1
92
30
Finish
SVX
External turning
Copying
Order Number
Stock
R L
H1
L1
L2
H2
Clamp
Screw
F1
*
Clamp Clamp Bridge
Wrench
Spring Wrench
Bridge
Screw
(Insert) (Clamp Bridge)
SXZCR/L-102
a a
22pSVX
.625 .625 4.000 1.378 .625 .750 TS255 AMS3 AJS3010T10 ASS2 TKY08F TKY10F
-122
a a
XCMT 22pSVX
.750 .750 4.500 1.378 .750 1.000 TS255 AMS3 AJS3010T10 ASS2 TKY08F TKY10F
-162
a a
22pSVX
1.000 1.000 6.000 1.575 1.000 1.250 TS255 AMS3 AJS3010T10 ASS2 TKY08F TKY10F
Clamp Torque (lbf-in) : TS255=8.9, AJS3010T10=22
SXZC
DOUBLE CLAMP Type
External turning
Copying
F1
< 300
(2)
9230
L2
L1
H2
H1
92
30
Finish
SVX
Dimensions (inch)
Insert Number
Order Number
Stock
R L
Dimensions (mm)
Insert Number
H1
L1
L2
H2
F1
Clamp
Screw
*
Clamp Clamp Bridge
Wrench
Spring Wrench
Screw
Bridge
(Insert) (Clamp Bridge)
SXZCR/L1616H15
a a
22pSVX
16
16
100
35
16
20
TS255 AMS3 AJS3010T10 ASS2 TKY08F TKY10F
2020K15
a a
XCMT 22pSVX
20
20
125
35
20
25
2525M15
a a
22pSVX
25
25
150
40
25
32
* Clamp Torque (lbf-in) : TS255=8.9, AJS3010T10=22

y APPLICATION RANGE
Depth of cut (inch)

P
Corner Radius
Corner Radius
Work Material
Hardness
Grade
Cutting Speed
(SFM)
Mild Steel
< 180HB
UE6020
490 1150
UE6020
330 820
General Steel 150HB 250HB
(Note) The above cutting conditions are general guide lines.

Adjustments maybe necessary depending on machine
rigidity, workpiece geometry and clamping.
Feed (IPR)
C038
SXZC type inserts
A136
OPERATIONAL GUIDANCE
Depth from end face

Up to .394"
Inclination angle
60 or less
Machining of V-pulleys
Machining of an outer diameter (Step z )

To prevent burr formation, the depth of cut should be
below half the corner radius.
Machining of an inclination (Step x)
2
Cutting diameter
1.575" or larger
Pay special attention to the

following when face copying.
Not possible
Notes when end face copying
To reduce the contact length of chips, the depth of cut

should be below half the corner radius.
To prevent interference between the tool and the
workpiece, the cutting diameter should be 1.575" or
larger, inclination angle 60 or less and depth from the
end face up to .394".
When changing inserts

When indexing the inserts, it is recommended to preset
the cutting edge position to maintain machining
accuracy.
When machining V-pulleys,

use a VNMG insert.
SPARE PARTS
M001
TECHNICAL DATA
N001
C039
ii INSERTS
RP TOOL HOLDERS
SRDPR/L
Screw Clamp Type

SP Holder
External turning
Copying
Medium
JS
(12)
Order Number
Stock
R L
SRDPR/L-1612
a a
RPMT120400E-JS
Dimensions (inch)
Insert Number
D1
H1
L1
L2
H2
.500
1.000
1.000
6.000
1.000
1.000
Clamp Screw Wrench

TS43
TKY15F
Clamp Torque (lbf-in) : TS43=31
SRDPN
Screw Clamp Type

SP Holder
External turning
Copying
Medium
JS
(12)
Order Number
Stock
Insert Number
SRDPN-1612
RPMT120400E-JS
Dimensions (inch)
D1
H1
L1
L2
H2
.500
1.000
1.000
6.000
1.000
1.000
Clamp Screw Wrench

TS43
TKY15F
* Clamp Torque (lbf-in) : TS43=31
C040
SRDPR/L type inserts
J019
SRDPN type inserts
J019
i i INSERTS
DE TOOL HOLDERS
Screw Clamp Type for Aluminum
AL Holder
F1
(4)
93
L2
PCD
L1
93
Medium
R/L
External turning
Copying
R/L-F
H2
H1
(4)
Order Number
Stock
R L
SDJER/L -104
a a
-124
a a
-164
a a
DEGX
Dimensions (inch)
Insert Number
H1
L1
L2
H2
F1
Clamp Screw Wrench
43pR/L
.625
.625
4.000
1.000
.625
.750
CS451190T TKY20F
43pR/L
.750
.750
4.500
1.000
.750
.875
CS451190T TKY20F
43pR/L
1.000
1.000
6.000
1.100
1.000
1.250
CS451190T TKY20F
SDJE
Clamp Torque (lbf-in) : CS451190T=44

Work Material
Aluminum Alloy
Grade
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
HTi10
1310
.002 .012
.008 .118
SDJE type inserts
A114
SPARE PARTS
M001
PCD inserts
B065
TECHNICAL DATA
N001
C041
ii INSERTS
TE TOOL HOLDERS
STGE

AL Holder
Medium
R/L
F1
External turning
(3)
PCD
H2
91
R/L
L1
7
7
H1
91
L2
(3)
Order Number
Stock
R L
STGER/L -103
a a
-123
a a
-163
a a
TEGX
Dimensions (inch)
Insert Number
H1
L1
L2
H2
F1
Clamp Screw Wrench
32pR/L
.625
.625
4.000
.800
.625
.750
FC400890T TKY10F
32pR/L
.750
.750
4.500
.800
.750
.875
FC400890T TKY10F
32pR/L
1.000
1.000
6.000
.900
1.000
1.250
FC400890T TKY10F
(Note) Right hand toolholder uses right hand insert. Left hand toolholder uses left hand insert.
Clamp Torque (lbf-in) : FC400890T=22
STFE

AL Holder
91
Medium
R/L
F1
Facing
91
(3)
L2
PCD
L1
R/L
H2
H1
(3)
Order Number
Stock
R L
STFER/L -103
a a
-123
a a
-163
a a
TEGX
Dimensions (inch)
Insert Number
H1
L1
L2
H2
F1
Clamp Screw Wrench
32pR/L
.625
.625
4.000
.866
.625
.750
FC400890T TKY10F
32pR/L
.750
.750
4.500
.866
.750
1.000
FC400890T TKY10F
32pR/L
1.000
1.000
6.000
.866
1.000
1.250
FC400890T TKY10F
(Note) Right hand toolholder uses left hand insert. Left hand toolholder uses right hand insert.
C042
STGE type inserts
A121
STFE type inserts
A121
PCD inserts
B065
ii INSERTS
VD TOOL HOLDERS
Finish
F1
R/L
(3)
PCD
11730
117
30
R/L-F
7
H1
H2
L1
(3)
Order Number
Stock
R L
SVPDR/L -123
a a
-163
a a
H1
VDGX
Dimensions (inch)
Insert Number
B
L1
H2
F1
Clamp Screw Wrench
32pR/L
.750
.750
4.500
.750
1.000
FC400890T TKY10F
32pR/L
1.000
1.000
6.000
1.000
1.250
FC400890T TKY10F
SVPD

AL Holder
External turning
Copying
SVJD

AL Holder
External turning
Copying
Finish
R/L
F1
L1
(3)
PCD
93
93
R/L-F
L2
H1
H2
(3)
Order Number
Stock
R L
SVJDR/L -103
a a
-123
a a
-163
a a
VDGX
Dimensions (inch)
Insert Number
H1
L1
L2
H2
F1
Clamp Screw Wrench
32pR/L
.625
.625
4.000
1.100
.625
.750
FC400890T TKY10F
32pR/L
.750
.750
4.500
1.100
.750
.875
FC400890T TKY10F
32pR/L
1.000
1.000
6.000
1.200
1.000
1.250
FC400890T TKY10F

Work Material
Aluminum Alloy
Grade
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
HTi10
1310
.002 .012
.008 .118
SVPD type inserts
A130
SVJD type inserts
A130
SPARE PARTS
M001
PCD inserts
B066
TECHNICAL DATA
N001
C043
ii INSERTS
RG TOOL HOLDERS
SRSGR/L
Screw Clamp Type

SR Holder
External turning
Copying
Medium
Standard
(20)
Right hand tool

holder shown.
Order Number
Stock
R L
SRSGR/L -1620M
-8520M
a a
RGGM2004M0
a
Dimensions (inch)
Insert Number
Clamp Screw Wrench
H1
L1
L2
H2
F1
1.000
1.000
6.000
1.181
1.000
1.250
TS5
TKY25F
1.250
1.000
7.000
1.181
1.250
1.250
TS5
TKY25F
SRSGN
Screw Clamp Type

SR Holder
External turning
Medium
Standard
(20)
Order Number
Stock
SRSGN -1620M
-8520M
RGGM2004M0
Dimensions (inch)
Insert Number
Clamp Screw Wrench
H1
L1
L2
H2
F1
1.000
1.000
6.000
.310
1.000
.500
TS5
TKY25F
1.250
1.000
7.000
.310
1.250
.500
TS5
TKY25F
* Clamp Torque (lbf-in) : TS5=66
C044
: Inventory maintained. (10 inserts in one case)

s : Inventory maintained in Japan. (1 insert in one case for CBN)
a
SRSGR/L type inserts
A116
SRSGN type inserts
A116
TL HOLDER
Taper Lock Type
TL Holder
Order Number
Stock
Dimensions (inch)
Insert Number
R L
D1
H1
L1
L3
H2
F1
TLHR/L -125
a a
05A
.197
.750
.750
5.000
.625
.750
.776
-126
a a
06A
.236
.750
.750
5.000
.625
.750
.776
-167
a a
07A
.276
1.000
1.000
6.000
.750
1.000
1.023
-168
a a
08A
.315
1.000
1.000
6.000
.750
1.000
1.023
-8510
a a
10A
.394
1.250
1.000
6.750
1.000
1.250
1.034
TLHN
Order Number
RTG
Taper Lock Type

TL Holder
External turning
Copying
Stock
Dimensions (inch)
Insert Number
D1
H1
L1
L3
H2
F1
TLHN -125
05A
.197
.750
.750
5.000
.625
.750
.474
-126
06A
.236
.750
.750
5.000
.625
.750
.493
-167
07A
.276
1.000
1.000
6.000
.750
1.000
.638
-168
08A
.315
1.000
1.000
6.000
.750
1.000
.658
-8510
10A
.394
1.250
1.000
6.750
1.000
1.250
.697
RTG
TLHR/L
External turning
Copying
(Tangential
angle )
INSERTS
Insert Number
RTG05A
06A
07A
08A
10A
Stock
Uncoated
UTi20T
HTi10
CBN
MB825
Dimensions (inch)
D1
D4
L2
L5
.197
.236
.098
.138
.295
.295
.138
.138
.276
.138
.433
.197
.315
.394
.177
.217
.433
.551
.197
.256
SPARE PARTS
M001
TECHNICAL DATA
N001
C045
GUIDE TO SMALL TOOLS

a Section
organization
z Organized according to cutting mode of small tools.

x In order of Turning|External Grooving|External Cutting Off|Threading|Boring.

uses illustrations and arrows to depict the available
machining applications such as external turning,
copying, facing, and chamfering together with
cutting edge lead angles.
TYPE OF TOOL HOLDER

GEOMETRY
APPLICATION
CHIP BREAKER BY
CUTTING APPLICATION
PRODUCT SECTION
SMALL TOOLS
GANG TYPE
)
TOOL POSTS
FRONT TURNING TOOLS (FOR
INCH STANDARD
INCH STANDARD
(2,3)
Order Number
L2
L9
H2
S1
Insert Screw
Wrench
H1
21.5p
.375 .375 4.921
.375
TS254
TKY08R
SDJCR/L-062SM
a a
.375 .375 4.921 .630 .156 .375
TS43
TKY15R
-063SM
a a
.500 .500 5.906 .504 .031 .500
TS43
TKY15R
-083SM
a a
32.5p
.625 .625 5.906
TS43
TKY15R
-103SM
a a
.625
Finish
95
L1
SMG
a a
-063SM
a a
-083SM
a a
-103SM
a a
(2)
(2)
Flat Top
L9
(2,3)
(2,3)
L1
(2,3)
Non-Ferrous Metal CBN/PCD

AZ
(2,3)
(2,3)
(2,3)
L2
L9
H2
S1
Insert Screw
Wrench
21.5p
.375 .375 4.921
.375
TS254
TKY08R
32.5p
.375 .375 4.921 .965 .176 .375
TS43
TKY15R
32.5p
.500 .500 5.906 .843 .051 .500
TS43
TKY15R
32.5p
.625 .625 5.906
TS43
TKY15R
Medium
R/L-SN
(2,3)
SDNC-SM
(2,3)

AZ
6230'
(2,3)
(2,3)
(2,3)
Order Number
Stock
.625
L9
H2
S1
Insert Screw
Wrench
.375
TS254
TKY08R
SDNCR/L-062SM
a a
TS43
TKY15R
-063SM
a a
.500 .500 5.906 .685 .051 .500
TS43
TKY15R
-083SM
a a
.625 .625 5.906
TS43
TKY15R
-103SM
a a
L1
32.5p
32.5p
.625
Light
Medium
R-SS
(2,3)
(2,3)
Medium
Flat Top
Right hand tool

holder shown.
R-SN
(2,3)
H1
L1
(2,3)

AZ
(2,3)
(2,3)
(2,3)
L2
L9
(2,3)
Dimensions (inch)
Insert Number
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
Finish
R-F
R-SR
R L
L2
.375 .375 4.921
Finish
SMG
L1
(2,3)
.375 .375 4.921 .807 .176 .375
21.5p
L2
62
30
Dimensions (inch)
32.5p
Neutral edge with handed holder

Without off set
H2
H1
Right hand tool

holder shown.
H1
CCET
CCGT
CCGW
CCMT
CCMW
NP-CCGW
Light
R/L-SS
R/L-SR
Insert Number
R L
SCLCR/L-062SM
Finish
R/L-F
Medium
L2
L9
Without off set
S1
Stock
Order Number
H1
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
Medium
R-SN
H2
95
(2,3)
Flat Top
Dimensions (inch)
Insert Number
R L
32.5p
SCLC-SM
Stock
32.5p
(2,3)
Medium
Right hand tool

holder shown.
(2,3)
Light
R-SS
R-SR
L1
H2
(2,3)
Finish
R-F
SMALL TOOLS
L1
93
93
a a
AZ
(2,3)
SMG
L9
-103SM
CCET
CCGT
CCGW
CCMT
CCMW
NP-CCGW
L2
(2,3)
Dimensions (inch)
H1
Finish
Without off set
H1
a a
(2,3)
SDJC-SM
S1
a a
-083SM
Medium
R/L-SN
S1
a a
-063SM
(2)
Flat Top
Right hand tool

holder shown.
Insert Number
R L
SCACR/L-062SM
(2)
R/L-SR
L1
H2
SMALL TOOLS
Stock
Order Number
Light
R/L-SS
Medium
L2
90
90
Finish
R/L-F
H1
SMG
S1
Finish
Without off set

L9
SCAC-SM
H2
S1
Insert Screw
Wrench
21.5p
.375 .375 4.921
TS254
TKY08R
32.5p
.375 .375 4.921 .965 .097 .375 .197
TS43
TKY15R
32.5p
.500 .500 5.906
.500 .197
TS43
TKY15R
32.5p
.625 .625 5.906
.625 .197
TS43
TKY15R
.375 .118

Work Material
Cutting Speed (SFM)
Grade
Feed (IPR)
VP15TF/UE6020
165 490
.0004 .006
VP15TF
100 590
.0004 .006
Free Cutting Carbon Steel
D008
AP25N
165 820
.0004 .006
Stainless Steel
VP15TF
165 395
.0008 .004
Non-Ferrous Metal
HTi10/RT9005
230 755
.0012 .006
SCAC-SM type inserts
A101 A106
SDJC-SM type inserts
A109 A113
SCLC-SM type inserts
A101 A106
SDNC-SM type inserts
A109 A113
SPARE PARTS
M001
CBN & PCD inserts
B038 B040, B058
CBN & PCD inserts
B042, B043, B059
TECHNICAL DATA
N001
LEGEND FOR STOCK

STATUS MARK
REFERENCE PAGE
D009
PAGE REFERENCE
SPARE PARTS
indicates reference pages giving details of TECHNICAL DATA
inserts that are applicable to the product. indicates reference pages,
including the above, on the right hand
PRODUCT STANDARDS
and spare parts.
aTo
D000
Order :

for each work material classication, indicates recommended cutting
conditions according to the ISO categories for cutting grades, P, M and N.
TURNING
SMALL TOOLS
*Arranged by Alphabetical order
D016
D019
D016
D017
D018
D021
D018
D041
D044
D042
D042
D042
D041
D041
D043
D043
D026
D028
D026
D028
D027
D017
D030
D020
D031
D030
D032
D032
D033
D033
D034
D034
D022
D024
D022
D038
D047
D047
D008
D012
D008
D012
D009
D013
D009
D013
D039
D040
D010
D014
D010
D014
D015
D011
D015
D035
D036
D035
BTAH (INCH STANDARD)

BTAH (METRIC STANDARD)
BTAT INSERTS
BTBT INSERTS
BTVH (INCH STANDARD)
BTVH (METRIC STANDARD)
BTVT INSERTS
CSVH (INCH STANDARD)
CSVH (METRIC STANDARD)
CSVTB INSERTS
CSVTBXL INSERTS
CSVTC INSERTS
CSVTF INSERTS
CSVTFXL INSERTS
CSVTG INSERTS
CSVTT INSERTS
CTAH (INCH STANDARD)
CTAH (METRIC STANDARD)
CTAH-S (INCH STANDARD)
CTAH-S (METRIC STANDARD)
CTAT INSERTS
CTBH (INCH STANDARD)
CTBH (INCH STANDARD)
CTBH (METRIC STANDARD)
CTBH (METRIC STANDARD)
CTBT INSERTS
CTCH (METRIC STANDARD)
CTCT INSERTS
CTDH (METRIC STANDARD)
CTDT INSERTS
CTEH (METRIC STANDARD)
CTET INSERTS
GTAH/GTBH/GTCH (INCH STANDARD)
GTAH/GTBH/GTCH (METRIC STANDARD)
GTAT/GTBT/GTCT INSERTS
MMTE (INCH STANDARD)
SBAH (METRIC STANDARD)
SBAT INSERTS
SCAC-SM (INCH STANDARD)
SCAC-SM (METRIC STANDARD)
SCLC-SM (INCH STANDARD)
SCLC-SM (METRIC STANDARD)
SDJC-SM (INCH STANDARD)
SDJC-SM (METRIC STANDARD)
SDNC-SM (INCH STANDARD)
SDNC-SM (METRIC STANDARD)
SH (INCH STANDARD)
SH (METRIC STANDARD)
SVJB-SM (INCH STANDARD)
SVJB-SM (METRIC STANDARD)
SVLP-SM (INCH STANDARD)
SVLP-SM (METRIC STANDARD)
SVPP-SM (METRIC STANDARD)
SVVB-SM (INCH STANDARD)
SVVB-SM (METRIC STANDARD)
TTAH (INCH STANDARD)
TTAH (METRIC STANDARD)
TTAT INSERTS
OUTLINE OF SMALL TOOLS .......................... D002

CLASSIFICATION............................................. D004
STANDARD
GANG TYPE TOOL POSTS
FRONT TURNING TOOLS
INCH
METRIC
SCAC-SM ..................................... D008 D012

SCLC-SM ...................................... D008 D012
SDJC-SM ...................................... D009 D013
SDNC-SM ..................................... D009 D013
SVLP-SM ...................................... D010 D014
SVJB-SM ...................................... D010 D014
SVVB-SM ...................................... D011 D015
SVPP-SM ...................................... D015
BACK TURNING TOOLS
BTAH ............................................ D016 D019
CTBH ............................................ D017 D020
BTVH ............................................ D018 D021
GROOVING TOOLS
GTAH / GTBH / GTCH .................. D022 D024
CUTTING OFF TOOLS
CTAH / CTAH-S ............................ D026 D028
CTBH ............................................ D030 D031
CTCH ...................................................... D032
CTDH ...................................................... D033
CTEH ...................................................... D034
THREADING TOOLS
TTAH ............................................. D035 D036
MMTE............................................ D038
BORING TOOLS
SBAH ...................................................... D047
OPPOSITE TOOL POSTS
DIMPLE SLEEVE HOLDER
SH ................................................. D039 D040
RADIAL TYPE TOOL POSTS
CSVH ............................................ D041 D044
CSVTF...................................... D041 D044
CSVTFXL ................................. D041 D044
CSVTC ..................................... D042 D045
CSVTB ..................................... D042 D045
CSVTBXL................................. D042 D045
CSVTG ..................................... D043 D046
CSVTT...................................... D043 D046
D001
SMALL TOOLS
OUTLINE OF SMALL TOOLS
SMALL TOOLS
TOOLS FOR GANG TYPE TOOL POSTS
Cutting Off
Back Turning
a SMG Breaker Insert
Corner radii designed with

minus tolerance
Grooving
Front Turning
Threading
a Tolerance Corner R
A combination of a curved
cutting edge and the
protrusion type breaker
promotes efcient chip
breaking.
Re
SMG breaker insert
a Suitable for precision parts applications that often
a Back Clamping
Mechanism
.138 inch
(3.5 mm)
a Front Turning
a3-cornered
aISO E class insert
aGroove width .012.118inch
aA wide variety of small corner R
aProling possible
20
D002
Can machine to the

shoulder
a Grooving
(0.3 3.0 mm)
The screw designed for common

use of front and back enables back clamping.
a Threading
a Back Turning
Step difference .256 inch

(6.5 mm)
Max. Cutting Off

diameter &1.378 inch
(&35 mm)
Sharp cutting edge
Over hang .295 inch

(7.5 mm)
0 20
Conventional G class
Re e .004 inch
Effective cutting edge length .236inch

(6.0 mm)
Cutting edge width

.028 .118 inch (0.7 3.0 mm)
E class
Re -0.002 inch Re -0.0008 inch
require minus tolerance dimensions.

a The order number is shown with the letter M that
indicates minus tolerance. ex) DCGT21.51MSMG
=
a The radius value is printed on the side of the insert
label for easy recognition.
a Cutting Off
Internal Turning
aRake angle 30
External Turning
Tools for front turning, back turning, grooving,

threading, and cutting off
Internal Turning
Tools for boring, internal grooving, and

internal threading
Drilling
Drills
End Milling
End mills
TOOLS FOR SWISS STYLE LATHES WITH RADIAL TOOL POSTS

a The
a The
most suitable for swiss style lathes with radial tool posts.
most suitable for machining of small parts with work
diameter &5 mm (.197 inch) or smaller.
a Single holder responds to front turning, back turning, grooving,
threading, and cutting off operations.
SMALL TOOLS
Tools responding to a wide range of

small parts machining operations
Tools for front turning, back turning, grooving,

threading, and cutting off
Tool Post Type
Gang type, Turret type

Radial type
Tool Size
Square holder : .375 .625 inch (8 16 mm)

Round holder : < &1 inch (& 25.4 mm)
Indexable inserts developed under the concept of

"high quality, high efciency, and long tool life."
High Quality
E class tolerance, sharp cutting edge, high

accuracy small corner R, smooth surface nish.
Long Tool Life
Miracle Coating (VP15TF), cermet (NX2525),

cemented carbide (HTi10).
High Efciency
Regrinding not necessary due to the employment of indexable inserts.

A wide variety of top cutting edge geometries.
INTERNAL TURNING TOOLS

MICRO-MINI TWIN Boring bars
Min. cutting diameter &2.2 mm
Front Turning
Back Turning
Grooving
Threading
Cutting Off
DRILLING TOOLS
aSolid Carbide Drills
Boring
Grooving
Threading
TAF Drill
Round holder
Min. cutting diameter

& .468 inch
END MILLING TOOLS
Square holder
aSolid Carbide End Mills
MICRO-DEX
Boring bars
Min. cutting diameter &5.0 mm
DIMPLE BAR
Min. cutting diameter
& .39 inch
D003
SMALL TOOLS
CLASSIFICATION (EXTERNAL TURNING)

a THREADING
GANG TYPE TOOL POSTS

Name of
Tool Holder
SCAC-SM
Tool Size (H x W x L)
Inch
Metric
SMALL TOOLS
TTAH
Geometry
.375 x .375 x 4.921 8 x 8 x 125

.500 x .500 x 5.906 10 x 10 x 125
.625 x .625 x 5.906 12 x 12 x 150
16 x 16 x 150
Inch
93
.375 x .375 x 4.921 8 x 8 x 125
.500 x .500 x 5.906 10 x 10 x 125
.625 x .625 x 5.906 12 x 12 x 150
16 x 16 x 150
62
30
.375 x .375 x 5.000 10 x 10 x 125

.500 x .500 x 6.000 12 x 12 x 150
.625 x .625 x 6.000 16 x 16 x 150
95
.375 x .375 x 4.921 10 x 10 x 125
.500 x .500 x 5.906 12 x 12 x 150
.625 x .625 x 5.906 16 x 16 x 150
93
^ D010
Inch
Metric ^ D014
SVPP-SM
.375 x .375 x 4.921 10 x 10 x 125

.500 x .500 x 5.906 12 x 12 x 150
.625 x .625 x 5.906 16 x 16 x 150
a BACK TURNING
x
x
x
x
.375
(Grooving Width) .375
.057-.089 inch .500
1.45-3.0 mm .625
Inch
^ D022
Metric ^ D024
.375
.375
.500
.625
3.150
4.724
4.724
4.724
.375 x .375 x 3.150 10 x 10 x 80

(Grooving Width) .375 x .375 x 4.724 10 x 10 x 120
.098-.118 inch
2.5-3.0 mm
Inch
^ D022
Metric ^ D024
Inch
Metric
.375 x .375 x 4.724 8 x 10 x 120

(Max.Cut Off Diameter) .500 x .500 x 4.724 10 x 10 x 120
.472 inch .625 x .625 x 4.724 12 x 12 x 120
16 x 16 x 120
12 mm
Inch ^ D026
Metric ^ D028
.375 x .375 x 3.150 10 x 10 x 80
(Max.Cut Off Diameter) .500 x .500 x 3.150
.472 inch
12 mm
Inch ^ D026
Metric ^ D028
10 x 10 x 120
12 x 12 x 120
Metric ^ D032
CTDH
(Max.Cut Off Diameter)
.906-1.378 inch
23-35 mm
BTVH
16 x 16 x 120
16 x 16 x 125
Metric ^ D033
CTEH
53
VT Type
U Type
E Type
VT Type
U Type
E Type
VT Type
a CUTTING OFF

.787 inch
20 mm
.375 x .375 x 4.724 10 x 10 x 120

.500 x .500 x 4.724 12 x 12 x 120
(Edge Length)
.177, .236 inch .625 x .625 x 4.724 16 x 16 x 120
4.5, 6.0 mm
^ D017
Inch
Metric ^ D020
U Type
E Type
GTCH
CTCH
CTBH
Geometry
10 x 10 x 80
10 x 10 x 120
12 x 12 x 120
16 x 16 x 120
.375 x .375 x 4.724 10 x 10 x 120

(Max.Cut Off Diameter) .500 x .500 x 4.724 12 x 12 x 120
.630 inch .625 x .625 x 4.724 16 x 16 x 120
16 mm
Inch ^ D030
Metric ^ D031
.375 x .375 x 4.724 8 x 10 x 120

.500 x .500 x 4.724 10 x 10 x 120
(Edge Length)
.110, .138, .197 inch .625 x .625 x 4.724 12 x 12 x 120
16 x 16 x 120
2.8, 3.5, 5.0 mm
^ D016
Inch
Metric ^ D019

.906-1.378 inch
23-35 mm
Metric ^ D034
D004
x
x
x
x
CTBH
Geometry
BTAH
.375 x .375 x 4.724 10 x 10 x 120

.500 x .500 x 4.724 12 x 12 x 120
(Edge Length)
.295 inch .625 x .625 x 4.724 16 x 16 x 120
7.5 mm
^ D018
Inch
Metric ^ D021
GTBH
3.150 8 x 8 x 80
3.150 8 x 8 x 120
4.724 10 x 10 x 80
4.724 10 x 10 x 120
12 x 12 x 80
12 x 12 x 120
16 x 16 x 120
CTAH-S
72
30
Inch
Metric
x
x
x
x
CTAH
117
30
^ D011
Inch
Metric ^ D015
Name of
Tool Holder
Inch
Metric
.375 x .375
GTAH
(Grooving Width) .500 x .500
.012-.055 inch .500 x .500
0.3-3.0 mm .625 x .625
^ D022
Inch
Metric ^ D024
Name of
Tool Holder
10 x 10 x 125
12 x 12 x 150
16 x 16 x 150
Metric ^ D015
SVVB-SM
^ D038
Name of
Tool Holder
.375 x .375 x 4.921 8 x 8 x 125

.500 x .500 x 5.906 10 x 10 x 125
.625 x .625 x 5.906 12 x 12 x 150
16 x 16 x 150
^ D010
Inch
Metric ^ D014
SVJB-SM
.375 x .375 x 4.724

.500 x .500 x 4.724
a GROOVING
^ D009
Inch
Metric ^ D013
SVLP-SM
MMTE
95
Inch
^ D009
Metric ^ D013
SDNC-SM
.375 x .375 x 4.724 8 x 10 x 120

.500 x .500 x 4.724 10 x 10 x 120
.625 x .625 x 4.724 12 x 12 x 120
16 x 16 x 120
.375 x .375 x 4.921 8 x 8 x 125

.500 x .500 x 5.906 10 x 10 x 125
.625 x .625 x 5.906 12 x 12 x 150
16 x 16 x 150
^ D008
Inch
Metric ^ D012
SDJC-SM
Geometry
Inch
^ D035
Metric ^ D036
90
^ D008
Inch
Metric ^ D012
SCLC-SM
Inch
Metric
Name of
Tool Holder
a FRONT TURNING
16 x 16 x 120
16 x 16 x 125
Geometry
Name of
Tool Holder
a DIMPLE SLEEVE HOLDER

Name of
Tool Holder
SH
^ D039
Inch
Metric ^ D040
SVVB
Shank Size (D x L)
Inch
Metric
.625
.750
.787
.866
1.000
x
x
x
x
x
3.937
4.921
4.921
4.921
5.906
&15.875
&19.05
&20
&22
&25.4
x
x
x
x
x
Geometry
100
125
125
125
150
Inch
SVHB
Geometry
.375 x .375 x 2.500

.500 x .500 x 3.000
.625 x .625 x 4.000
72
30
^ C028
93
Inch
Shank Size (inch)

(H x W x L)
.375 x .375 x 2.500

.500 x .500 x 3.500
.625 x .625 x 4.000
17
30
^ C029
SMALL TOOLS
OPPOSITE TOOL POSTS
TURRET TYPE TOOL POSTS

a FRONT TURNING
Name of
Tool Holder
SCLC
Inch
Geometry
Name of
Tool Holder
.375 x .375 x 2.500

.500 x .500 x 3.500
.625 x .625 x 4.000
CSVH
(Front Turning)
95
^ C030
SDJC
RADIAL TYPE TOOL POSTS
Shank Size (inch)

(H x W x L)
CSVH
(Front Copying)
CSVH
62
30
(Back Turning)
CSVH
(Cutting Off)
91
.375 x .375 x 2.500
.500 x .500 x 3.500
.625 x .625 x 4.000
91
.375 x .375 x 5.512

.500 x .500 x 5.512
7 x 7 x 140
8 x 8 x 140
9.5 x 9.5 x 140
10 x10 x 140
12 x12 x 140
.375 x .375 x 5.512

.500 x .500 x 5.512
7 x 7 x 140
8 x 8 x 140
9.5 x 9.5 x 140
10 x10 x 140
12 x12 x 140
CSVH
.375 x .375 x 5.512

.500 x .500 x 5.512
7 x 7 x 140
8 x 8 x 140
9.5 x 9.5 x 140
10 x10 x 140
12 x12 x 140
.375 x .375 x 5.512

.500 x .500 x 5.512
7 x 7 x 140
8 x 8 x 140
9.5 x 9.5 x 140
10 x10 x 140
12 x12 x 140
^ C035
SVJC
Inch
^ D043
Metric ^ D046
.375 x .375 x 2.500

.500 x .500 x 3.500
.625 x .625 x 4.000
93
CSVH
(Threading)
^ C036
SVPC
Inch
7 x 7 x 140
8 x 8 x 140
9.5 x 9.5 x 140
10 x10 x 140
12 x12 x 140
Inch
^ D042
Metric ^ D045
(Grooving)
Inch
.375 x .375 x 5.512

.500 x .500 x 5.512
Inch
^ D042
Metric ^ D045
.375 x .375 x 2.500

.500 x .500 x 3.500
.625 x .625 x 4.000
^ C035
STFC
(Back Turning)
45
^ C034
STGC
Inch
7 x 7 x 140
8 x 8 x 140
9.5 x 9.5 x 140
10 x10 x 140
12 x12 x 140
Inch
^ D042
Metric ^ D045
.500 x .500 x 3.500

.625 x .625 x 4.000
CSVH
Inch
.375 x .375 x 5.512

.500 x .500 x 5.512
Inch
^ D041
Metric ^ D044
.375 x .375 x 2.500

.500 x .500 x 3.500
.625 x .625 x 4.000
^ C031
SSSC
Inch
7 x 7 x 140
8 x 8 x 140
9.5 x 9.5 x 140
10 x10 x 140
12 x12 x 140
^ C031
SDNC
Inch
.375 x .375 x 5.512

.500 x .500 x 5.512
Inch
^ D041
Metric ^ D044
.375 x .375 x 2.500

.500 x .500 x 3.500
.625 x .625 x 4.000
93
Inch
Inch
Metric
117
30
^ C036
SVJB
Inch
^ D043
Metric ^ D046
.500 x .500 x 3.500

.625 x .625 x 4.000
Geometry
.375 x .375 x 2.500

.500 x .500 x 3.500
.625 x .625 x 4.000
93
Inch
^ C028
D005
SMALL TOOLS
CLASSIFICATION (INTERNAL TURNING)

' = 75
Min.
Cutting
Dia.
Name of Tool Holder
For Gang Type Tool Posts
&3.0mm SBAH
& .118
inch
SMALL TOOLS
Features
'
'
The minimum cutting

diameter is & 3mm
(.118inch).
a Tools for Gang type
Swiss type lathes.
a
SBAH
^ D047
& 2.2mm
|
MICRO-MINI TWIN
Boring Bars
& 7.2mm
& .087
(Solid Carbide)
|
& .283
inch
& 3.2mm MICRO-MINI
|
& 5.2mm Boring Bars
(Solid Carbide)
& .126
|
& .205
inch
& 5.0mm MICRO-DEX
|
& 8.0mm Boring Bars
& .197
|
& .315
inch
( )
( )
( )
& .390
inch
|
& .977
inch
SCREW CLAMP DIMPLE BAR

(Heavy Metal Shank)
(Steel Shank)
& .228
inch
|
& .937
inch
Screw Clamp Type

Boring Bars
& .200
inch
|
& .750
inch
Screw Clamp Type

Boring Bars
& .228
inch
|
& .797
inch
Screw Clamp Type

Boring Bars
(Steel Shank)
The minimum cutting diameter

is &2.2mm (.087inch).
a Two cutting edges type.
a Continuous cutting from boring
to facing.
a With or without a chip breaker.
a
a
a
a
a
^ E031
SWUB
^ E029
The minimum cutting

diameter is &.390inch.
a 7, 11 positive insert.
a Excellent vibration resistance
due to light dimple head.
a Coolant thru type.
a
Two wall pocket.

a 7 positive insert,
low cutting force.
a Screw clamp type.
a Steel, heavy metal and
carbide shanks are
available in various
diameters.
M/S-FSTUP
M-FSDUC M ^ E007 M-FSVUB/C M-FSWUB/P
^ E008
S ^ E007
S-SDUC
S-STUC
^ E009
^ E009
S-SSKC
^ E015
^ E014
^ E015
(Heavy Metal Shank)
(Carbide Shank)
C-STUC
^ E016
Multi-functional bar
for threading, grooving
and boring.
a Minimum bore & .390inch.
a Rigid insert retention.
SL5 Type Boring Bars
& 10mm
F Type Boring Bars

(FSL51,52)
( )
CppFR-BLS

is from & 5mm (.197inch).
a 7positive insert.
a Carbide shank type.
a Easy-to-use tool geometries.
a Suitable for small workpiece.
a l/d is 5 times the diameter.
& .390
inch
|
& .790
inch
|
The minimum cutting diameter is

from &3.2mm (.126inch).
Single cutting edge type.
l/d is 5 times the diameter.
Cutting edge can be shaped
according to the application.
Thus, it covers a wide cutting range.
(threading, grooving, copying, etc.)
& 20mm
& .394
|
& .787
inch

is &10mm (.394inch).
a Single holder can be
equipped with grooving
inserts and threading
inserts.
(Note 1) Products with blue color symbol have carbide shank.
D006
' = 93
S-SWUC
^ E019
Threading
CRppRS-01(-B) CGppRS-pp(-B) CTppRSMp(B)
CBppRS(-B)
^ E032
^ E033
^ F165
^ G039
SMALL TOOLS
'
Small Diameter
Cutting
Selection Standard
Specialized
Grooving
Coolant Thru
'
' = 142
Vibration
Resistance
'
Low Cutting
Resistance
' = 1073011730
Economical
' = 95
SCLC
^ E029
M/S-FSCLC/P
M ^ E006
S ^ E006
M-FSDQC
^ E008
M-FSVPB/C
^ E010
^ E010
e
S-SCLC
S-SDQC
^ E012
^ E013
M-SCLC
M-SWLO
C-SCLC
C-SWLO
^ E012
^ E013
M-FSVJC
S-SVQC
^ E016
^ E020
^ E019
C-SDQC
^ E014
S-SL5N
^ F163
S-SL5N
^ G037
FSL51, FSL52 FSL51, FSL52

^ F162
^ G036
(Note 2) e: 1st recommendation. u: 2nd recommendation.
D007
SMALL TOOLS
GANG TYPE
)
TOOL POSTS
INCH STANDARD
Finish
Without off set
Stock
a a
-063SM
a a
-083SM
a a
-103SM
a a
(2)
Flat Top
H1
Right hand tool

holder shown.
H1
CCET
CCGT
CCGW
CCMT
CCMW
NP-CCGW
Medium
R/L-SN
(2,3)
L1
(2,3)

AZ
(2,3)
(2,3)
(2,3)
(2,3)
Dimensions (inch)
Insert Number
R L
SCACR/L-062SM
(2)
R/L-SR
L1
H2
SMALL TOOLS
Order Number
Light
R/L-SS
Medium
L2
90
90
Finish
R/L-F
L9
SMG
S1
SCAC-SM
L2
L9
H2
S1
Insert Screw
Wrench
21.5p
.375 .375 4.921
.375
TS254
TKY08R
32.5p
.375 .375 4.921 .630 .156 .375
TS43
TKY15R
32.5p
.500 .500 5.906 .504 .031 .500
TS43
TKY15R
32.5p
.625 .625 5.906
TS43
TKY15R
.625
Stock
a a
-063SM
a a
-083SM
a a
-103SM
a a
(2)
Flat Top
H1
Right hand tool

holder shown.
H1
CCET
CCGT
CCGW
CCMT
CCMW
NP-CCGW
Medium
R/L-SN
(2,3)
L1
(2,3)

AZ
(2,3)
(2,3)
(2,3)
(2,3)
Dimensions (inch)
Insert Number
R L
SCLCR/L-062SM
(2)
R/L-SR
L1
H2
Order Number
Light
R/L-SS
Medium
L2
95
95
Finish
R/L-F
L9
SMG
S1
SCLC-SM
Finish
Without off set
L2
L9
H2
S1
Insert Screw
Wrench
21.5p
.375 .375 4.921
.375
TS254
TKY08R
32.5p
.375 .375 4.921 .807 .176 .375
TS43
TKY15R
32.5p
.500 .500 5.906 .685 .051 .500
TS43
TKY15R
32.5p
.625 .625 5.906
TS43
TKY15R
.625
D008
A101 A106
A101 A106
CBN & PCD inserts
B038 B040, B058
INCH STANDARD
Finish
Without off set
S1
93
-063SM
a a
-083SM
a a
-103SM
a a
H1
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
Medium
R-SN
(2,3)
AZ
(2,3)
L1
(2,3)
(2,3)
(2,3)
(2,3)
Dimensions (inch)
Insert Number
R L
a a
(2,3)
Flat Top
Right hand tool

holder shown.
H1
Stock
SDJCR/L-062SM
(2,3)
R-SR
L1
H2
Order Number
Light
R-SS
Medium
L2
93
Finish
R-F
L9
SMG
L2
L9
H2
S1
Insert Screw
Wrench
21.5p
.375 .375 4.921
.375
TS254
TKY08R
32.5p
.375 .375 4.921 .965 .176 .375
TS43
TKY15R
32.5p
.500 .500 5.906 .843 .051 .500
TS43
TKY15R
32.5p
.625 .625 5.906
TS43
TKY15R
.625
SMALL TOOLS
SDJC-SM
SDNC-SM

Without off set
H1
H2
a a
-063SM
a a
-083SM
a a
-103SM
a a
(2,3)
Flat Top
Medium
R-SN
(2,3)
Right hand tool

holder shown.
H1
L1
(2,3)

AZ
(2,3)
(2,3)
(2,3)
L2
L9
(2,3)
Dimensions (inch)
R L
SDNCR/L-062SM
(2,3)
R-SR
L1
Insert Number
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
Light
R-SS
Medium
S1
6230'
Stock
Finish
R-F
L9
L2
62
30
Order Number
Finish
SMG
H2
S1
.375 .118
Insert Screw
Wrench
TS254
TKY08R
21.5p
.375 .375 4.921
32.5p
.375 .375 4.921 .965 .097 .375 .197
TS43
TKY15R
32.5p
.500 .500 5.906
.500 .197
TS43
TKY15R
32.5p
.625 .625 5.906
.625 .197
TS43
TKY15R

Work Material
Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF/UE6020
165 490
.0004 .006
VP15TF
100 590
.0004 .006
AP25N
165 820
.0004 .006
Stainless Steel
VP15TF
165 395
.0008 .004
Non-Ferrous Metal
HTi10/RT9005
230 755
.0012 .006
A109 A113
A109 A113
SPARE PARTS
M001
CBN & PCD inserts
B042, B043, B059
TECHNICAL DATA
N001
D009
SMALL TOOLS
GANG TYPE
)
TOOL POSTS
INCH STANDARD
SVLP-SM
Finish
Without off set

S1
R/L-SRF
(1.5, 2)
95
SMG
H1
H2
SMALL TOOLS
95
Finish
L1
Order Number
Stock
R L
Dimensions (inch)
Insert Number
(1.5, 2)
H1
L1
H2
S1
Insert Screw
Wrench
.375
5.000
.375
TS202
TKY06R
SVLPR-061.5SM
1.51.5p
.375
-081.5SM
1.51.5p
.500
.500
6.000
.500
TS202
TKY06R
22p
.375
.375
5.000
.375
TS255
TKY08R
VPET
VPGT
SVLPR/L-062SM
a a
-082SM
a a
22p
.500
.500
6.000
.500
TS255
TKY08R
-102SM
a a
22p
.625
.625
6.000
.625
TS255
TKY08R
* Clamp Torque (lbf-in) : TS202=5.3, TS255=8.9
SVJB-SM
Finish
Without off set

S1
93
L1
(2)
(2)
Medium
Medium
MV
Order Number
Stock
SVJBR/L-062SM
-082SM
a a
-102SM
a a
VBET
VBGT
VBMT
(2)
(2)
Dimensions (inch)
Insert Number
H1
L1
H2
S1
Insert Screw
Wrench
22p
.375
.375
4.921
.375
TS255
TKY08R
22p
.500
.500
5.906
.500
TS255
TKY08R
22p
.625
.625
5.906
.625
TS255
TKY08R
R L
a a
R/L-SR
H1
H2
93
Medium
R/L-SN
R/L-F
* Clamp Torque (lbf-in) : TS255=8.9
D010
SVLP-SM type inserts
A131
SVJB-SM type inserts
A125 A127
CBN & PCD inserts
B047, B063
INCH STANDARD
SVVB-SM
Finish
Medium
R/L-SN
7230'
L1
MV
Order Number
Stock
a a
-082SM
a a
-102SM
a a
R/L-SR
VBET
VBGT
VBMT
(2)
(2)
Dimensions (inch)
Insert Number
H1
L1
H2
S1
Insert Screw
Wrench
22p
.375
.375
4.921
.375
.118
TS255
TKY08R
22p
.500
.500
5.906
.500
.118
TS255
TKY08R
22p
.625
.625
5.906
.625
.118
TS255
TKY08R
R L
SVVBR/L-062SM
(2)
Medium
H1
H2
72
30
(2)
Medium
SMALL TOOLS
S1
R/L-F

Work Material
Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF/UE6020
165 490
.0004 .006
VP15TF
100 590
.0004 .006
AP25N
165 820
.0004 .006
Stainless Steel
VP15TF
165 395
.0008 .004
Non-Ferrous Metal
HTi10/RT9005
230 755
.0012 .006
SVVB-SM type inserts
A125 A127
SPARE PARTS
M001
TECHNICAL DATA
N001
D011
SMALL TOOLS
GANG TYPE)
TOOL POSTS
METRIC STANDARD
Finish
Without off set
Stock
a a
1010K06-SM
a a
1010K09-SM
a a
1212M09-SM
a a
1616M09-SM
a a
(2)
Flat Top
H1
Right hand tool

holder shown.
CCET
CCGT
CCGW
CCMT
CCMW
NP-CCGW
Medium
R/L-SN
(2,3)
(2,3)

AZ
(2,3)
(2,3)
(2,3)
(2,3)
Dimensions (mm)
Insert Number
H1
L1
L2
L9
H2
S1
Insert Screw
Wrench
21.5p
125
11
1.6
TS254
TKY08R
21.5p
10
10
125
10
TS254
TKY08R
3.5
10
TS43
TKY15R
R L
SCACR/L0808K06-SM
(2)
R/L-SR
L1
H2
SMALL TOOLS
Order Number
Light
R/L-SS
Medium
L2
90
90
Finish
R/L-F
L9
SMG
S1
SCAC-SM
32.5p
10
10
125
16
32.5p
12
12
150
14
1.5
12
TS43
TKY15R
32.5p
16
16
150
16
TS43
TKY15R
Stock
H1
a a
1010K06-SM
a a
1010K09-SM
a a
1212M09-SM
a a
1616M09-SM
a a
(2)
Flat Top
Right hand tool

holder shown.
CCET
CCGT
CCGW
CCMT
CCMW
NP-CCGW
Medium
R/L-SN
(2,3)
(2,3)

AZ
(2,3)
(2,3)
(2,3)
(2,3)
Dimensions (mm)
Insert Number
H1
L1
L2
L9
H2
S1
Insert Screw
Wrench
21.5p
125
11
2.1
TS254
TKY08R
21.5p
10
10
125
10
TS254
TKY08R
32.5p
10
10
125
20
10
TS43
TKY15R
32.5p
12
12
150
18
12
TS43
TKY15R
32.5p
16
16
150
16
TS43
TKY15R
R L
SCLCR/L0808K06-SM
(2)
R/L-SR
L1
H2
Order Number
Light
R/L-SS
Medium
L2
95
95
Finish
R/L-F
L9
SMG
S1
SCLC-SM
Finish
Without off set
D012
A101 A106
A101 A106
CBN & PCD inserts
B038 B040, B058
METRIC STANDARD
Finish
Without off set
a a
1010K07-SM
a a
1010K11-SM
a a
1212M11-SM
a a
1616M11-SM
a a
(2,3)
Flat Top
H1
Right hand tool

holder shown.
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
(2,3)
(2,3)

AZ
(2,3)
(2,3)
(2,3)
(2,3)
Dimensions (mm)
Insert Number
H1
L1
L2
L9
H2
S1
Insert Screw
Wrench
21.5p
125
15
TS254
TKY08R
21.5p
10
10
125
10
TS254
TKY08R
32.5p
10
10
125
24
10
TS43
TKY15R
32.5p
12
12
150
22
12
TS43
TKY15R
32.5p
16
16
150
16
TS43
TKY15R
R L
SDJCR/L0808K07-SM
Medium
R-SN
SMALL TOOLS
Stock
(2,3)
R-SR
L1
H2
Order Number
Light
R-SS
Medium
L2
93
93
Finish
R-F
L9
SMG
S1
SDJC-SM

Without off set
Stock
a a
1010K07-SM
a a
1010K11-SM
a a
1212M11-SM
a a
1616M11-SM
a a
(2,3)
(2,3)
Flat Top
H1
Right hand tool

holder shown.
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
Medium
R-SN
(2,3)
(2,3)

AZ
(2,3)
(2,3)
(2,3)
(2,3)
Dimensions (mm)
Insert Number
H1
L1
L2
L9
H2
S1
Insert Screw
Wrench
21.5p
125
TS254
TKY08R
21.5p
10
10
125
10
TS254
TKY08R
10
TS43
TKY15R
R L
SDNCR/L0808K07-SM
Light
R-SS
R-SR
L1
H2
Order Number
Finish
R-F
Medium
B
6230'
62
30
Finish
SMG
L9
L2
S1
SDNC-SM
32.5p
10
10
125
24
32.5p
12
12
150
12
TS43
TKY15R
32.5p
16
16
150
16
TS43
TKY15R
A109 A113
A109 A113
SPARE PARTS
M001
CBN & PCD inserts
B042, B043, B059
TECHNICAL DATA
N001
D013
SMALL TOOLS
GANG TYPE)
TOOL POSTS
METRIC STANDARD
SVLP-SM
Finish
Without off set

S1
R/L-SRF
(1.5, 2)
95
SMG
H1
H2
SMALL TOOLS
95
Finish
L1
Order Number
Stock
R L
Dimensions (mm)
Insert Number
(1.5, 2)
H1
L1
H2
S1
Insert Screw
Wrench
SVLPR/L1010K08-SM
a a
1.51.5p
10
10
125
10
TS202
TKY06R
1212M08-SM
a a
1.51.5p
12
12
150
12
TS202
TKY06R
22p
10
10
125
10
TS255
TKY08R
VPET
VPGT
1010K11-SM
a a
1212M11-SM
a a
22p
12
12
150
12
TS255
TKY08R
1616M11-SM
a a
22p
16
16
150
16
TS255
TKY08R
* Clamp Torque (lbf-in) : TS202=5.3, TS255=8.9
SVJB-SM
Finish
Without off set

S1
93
L1
(2)
(2)
Medium
Medium
MV
Order Number
Stock
SVJBR/L1010K11-SM
1212M11-SM
a a
1616M11-SM
a a
VBET
VBGT
VBMT
(2)
(2)
Dimensions (mm)
Insert Number
H1
L1
H2
S1
Insert Screw
Wrench
22p
10
10
125
10
TS255
TKY08R
22p
12
12
150
12
TS255
TKY08R
22p
16
16
150
16
TS255
TKY08R
R L
a a
R/L-SR
H1
H2
93
Medium
R/L-SN
R/L-F
D014
SVLP-SM type inserts
A131
SVJB-SM type inserts
A125 A127
CBN & PCD inserts
B047, B063
METRIC STANDARD
SVVB-SM
Finish
Medium
R/L-SN
7230'
L1
MV
Order Number
Stock
a a
1212M11-SM
a a
1616M11-SM
a a
R/L-SR
VBET
VBGT
VBMT
(2)
(2)
Dimensions (mm)
Insert Number
H1
L1
H2
S1
Insert Screw
Wrench
22p
10
10
125
10
TS255
TKY08R
22p
12
12
150
12
TS255
TKY08R
22p
16
16
150
16
TS255
TKY08R
R L
SVVBR/L1010K11-SM
(2)
Medium
H1
H2
72
30
(2)
Medium
SMALL TOOLS
S1
R/L-F
SVPP-SM
Finish
R/L-SRF
Finish
11730'
L2
117
30
(2)
F2
S1
L3
SMG
L1
L2
H1
H2
SVPPR/L1616M11-SM
Order Number
Stock
H1
L1
L2
L3
H2
S1
Insert Screw
Wrench
22p
10
10
125
17
20
10
TS255
TKY08R
22p
12
12
150
17
20
12
TS255
TKY08R
22p
16
16
150
17
16
TS255
TKY08R
R L
SVPPR/L1010K11-SM
a a
1212M11-SM
a a
1616M11-SM
a a
VPET
VPGT
Dimensions (mm)
Insert Number
(2)

Work Material
Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF/UE6020
165 490
.0004 .006
VP15TF
100 590
.0004 .006
AP25N
165 820
.0004 .006
Stainless Steel
VP15TF
165 395
.0008 .004
Non-Ferrous Metal
HTi10
230 755
.0012 .006
SVVB-SM type inserts
A125 A127
SPARE PARTS
M001
SVPP-SM type inserts
A131
TECHNICAL DATA
N001
D015
SMALL TOOLS
GANG TYPE
)
BACK TURNING TOOLS (FOR
TOOL POSTS
INCH STANDARD
BTAH
SMALL TOOLS
(Effective Cutting Edge Length)
Order Number
Stock
R L
BTAHR/L-062
a a
-082
a a
-102
H1
5528ppR/L-B
6035ppR/L-B
605000RX
BTAT
Dimensions (inch)
Insert Number
B
L1
H2
H3
S1
Insert Screw
Wrench
.375
.375
4.724
.375
.500
.138
NS402W
NKY15R
.500
.500
4.724
.500
.138
NS403W
NKY15R
.625
.625
4.724
.625
.138
NS403W
NKY15R
(Note 1) Please use right hand insert for right hand holder and left hand insert for left hand holder.
(Note 2) Set the maximum depth of cut at under 60% of the effective cutting edge length.
Clamp Torque (lbf-in) : NS402W=6.2, NS403W=6.2
INSERTS
Hand
Coated
Dimensions (inch)
VP15TF
B3
Re
Effective Cutting
Edge Length
L4 (inch)
BTAT552800R-B
55
.110
552800L-B
55
.110
552801R-B
55
.004
.110
552801L-B
55
.004
.110
603500R-B
60
.138
603500L-B
60
.138
603501R-B
60
.004
.138
603501L-B
60
.004
.138
60
Geometry
With Breaker
.098
Order Number
.197
.315
12
50
Without Breaker
Re
.049
.787
.098
BTAT605000RX
.020
Re
.787
.315
12
50
* Numeric value set insert on holder.
D016
INCH STANDARD
CTBH
L1
.295
S1
3
60
.768
Order Number
Stock
R L
CTBHR/L-062
a a
-082
a a
-102
a a
H1
60450pR/L-B
606000R/L
BTBT
Dimensions (inch)
Insert Number
B
L1
H2
H3
S1
Insert Screw
Wrench
.375
.375
4.724
.375
.500
.133
NS402W
NKY15R
.500
.500
4.724
.500
.133
NS403W
NKY15R
.625
.625
4.724
.625
.133
NS403W
NKY15R
SMALL TOOLS
H3
H2
H1
L4 (Effective Cutting Edge Length)
INSERTS
VP15TF
Re
BTBT604500R-B
.008
.177
604500L-B
.008
.177
604501R-B
.004
.012
.177
604501L-B
.004
.012
.177
BTBT606000R
.008
.236
606000L
.008
.236
Geometry
* With Breaker
S2
S2
Effective Cutting
Edge Length
L4 (inch)
Dimensions (inch)
Re
.984
15

S2
.138
45
Without Breaker
.217
.028
Coated
.138
Hand
.370
Order Number
Re
.276
.028
.984
.370
15
45

Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF
165 490
.0004 .006
VP15TF
100 590
.0004 .006
Stainless Steel
VP15TF
165 395
.0008 .004
Non-Ferrous Metal
VP15TF
230 755
.0012 .006
Work Material
SPARE PARTS
M001
TECHNICAL DATA
N001
D017
SMALL TOOLS
GANG TYPE
)
TOOL POSTS
INCH STANDARD
S1
BTVH

.335
53
L1
H1
H2
SMALL TOOLS
53
Right hand tool holder only.
Order Number
Stock
R
BTVHR-062
-082
-102
BTVT
Dimensions (inch)
Insert Number
5375ppR-B
H1
L1
H2
S1
Insert Screw
Wrench
.375
.375
4.724
.375
.295
NS251
NKY15R
.500
.500
4.724
.500
.295
NS251
NKY15R
.625
.625
4.724
.625
.295
NS251
NKY15R
(Note) Set the maximum depth of cut at under 30% of the effective cutting edge length.
Clamp Torque (lbf-in) : NS251=6.2
INSERTS
VP15TF
D1
S1
Re
Effective Cutting
Edge Length
L4 (inch)
.250
.125
.002
.295
.250
.125
.004
.295
Order Number
Hand
BTVT5375V5R-B
537501R-B
Dimensions (inch)
Coated
Geometry
With Breaker
(.020)
Re
7
D1
D018
S1
L4
METRIC STANDARD
BTAH
L1
5.5
S1
15
Order Number
Stock
R L
BTAHR/L0810-50
a a
1010-50
a a
1212-50
a a
1616-50
H1
BTAT
Dimensions (mm)
Insert Number
5528ppR/L-B
6035ppR/L-B
605000RX
L1
H2
H3
S1
Insert Screw
Wrench
10
120
12
3.5
NS402W
NKY15R
10
10
120
10
12
3.5
NS402W
NKY15R
12
12
120
12
3.5
NS403W
NKY15R
16
16
120
16
3.5
NS403W
NKY15R
SMALL TOOLS
H1
H2
H3
B3 L4 (Effective Cutting Edge Length)
INSERTS
Dimensions (mm)
VP15TF
B3
Effective Cutting
Edge Length
L4 (mm)
Hand
BTAT552800R-B
55
552800L-B
55
2.8
552801R-B
55
0.1
2.8
552801L-B
55
0.1
2.8
603500R-B
60
3.5
603500L-B
60
3.5
603501R-B
60
0.1
3.5
603501L-B
60
0.1
3.5
Re
2.8
Geometry
With Breaker
2.5
Coated
Order Number
0.5
Re
20
12
60
5.0
Re
1.25
Without Breaker
2.5
BTAT605000RX
50
20
8
12
50

Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF
165 490
.0004 .006
VP15TF
100 590
.0004 .006
Stainless Steel
VP15TF
165 395
.0008 .004
Non-Ferrous Metal
VP15TF
230 755
.0012 .006
Work Material
SPARE PARTS
M001
TECHNICAL DATA
N001
D019
SMALL TOOLS
GANG TYPE
)
TOOL POSTS
METRIC STANDARD
CTBH
L1
7.5
S1
3
60
H1
H2
H3
SMALL TOOLS
19.5
Order Number
Stock
R L
CTBHR/L1010-160
a a
1212-160
a a
1616-160
a a
H1
BTBT
Dimensions (mm)
Insert Number
60450pR/L-B
606000R/L
L1
H2
H3
S1
Insert Screw
Wrench
10
10
120
10
12
3.4
NS402W
NKY15R
12
12
120
12
3.4
NS403W
NKY15R
16
16
120
16
3.4
NS403W
NKY15R
INSERTS
Re
Effective Cutting
Edge Length
L4 (mm)
BTBT604500R-B
0.2
4.5
604500L-B
0.2
4.5
604501R-B
0.1
0.3
4.5
604501L-B
0.1
0.3
4.5
Geometry
With Breaker
S2
S2
Dimensions (mm)
Re
5.5
0.7
Coated
VP15TF
3.5
Hand
25
15
9.4
Order Number
0.2
6.0
606000L
0.2
6.0
S2
Re
25
9.4
15
45
D020
0.7
BTBT606000R
3.5
45
Without Breaker
METRIC STANDARD
S1
BTVH
BTVHRpppp-75F
8.5
H1
H2
Order Number
Stock
Dimensions (mm)
Insert Number
H1
L1
H2
S1
Insert Screw
Wrench
BTVHR1010-75
10
10
120
10
7.5
NS251
NKY15R
1212-75
12
12
120
12
7.5
NS251
NKY15R
1616-75
16
16
120
16
7.5
NS251
NKY15R
1010-75F
10
10
120
10
10.0
NS251
NKY15R
1212-75F
12
12
120
12
10.0
NS251
NKY15R
1616-75F
16
16
120
16
10.0
NS251
NKY15R
BTVT
5375ppR-B
SMALL TOOLS
L1
53
53
(Note 2) For high load machining, F type is recommended.
INSERTS
VP15TF
D1
S1
Re
Effective Cutting
Edge Length
L4 (mm)
6.35
3.18
0.05
7.5
6.35
3.18
0.1
7.5
Order Number
Hand
BTVT5375V5R-B
537501R-B
Dimensions (mm)
Coated
Geometry
With Breaker
(0.5)
Re
7
D1
L4
S1

Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF
165 490
.0004 .006
VP15TF
100 590
.0004 .006
Stainless Steel
VP15TF
165 395
.0008 .004
Non-Ferrous Metal
VP15TF
230 755
.0012 .006
Work Material
SPARE PARTS
M001
TECHNICAL DATA
N001
D021
SMALL TOOLS
GANG TYPE
)
GROOVING TOOLS (FOR
TOOL POSTS
INCH STANDARD
GTAH, GTBH, GTCH
Long Shank
H2
H3
Stock
r r
Insert Number
r r
r r
r r
r r
r r
r r
GTAT 1
GTBT *1
GTCT*
GTBT. GTCT
GTCT
GTAT
1
GTBT *
1
GTCT *
a a
a a
GTBT. GTCT
a a
r r
F2*
*2
Cutting
Width
(inch)
H1
Insert Screw
Wrench
.375
.500
.375
.500
.375 3.150 .079

.500 3.150 .079
.531 .012.118
.520 .012.118
NS404W
NKY15R
NS404W
NKY15R
.375
.375
.375
.375
.375 3.150 .118

.375 3.150 .118
.531 .057.118
.531 .098.118
NS404W
NKY15R
NS404W
NKY15R
.375
.500
.375 4.724 .079

.500 4.724 .079
.531 .012.118
.520 .012.118
NS404W
NKY15R
pppp
.375
.500
NS404W
NKY15R
pppp
.625
.625
.625 4.724 .079
.012.118
NS404W
NKY15R
pppp
.375
.375
.375 4.724 .118
.531 .057.118
NS404W
NKY15R
pppp
.500
.500
.500 4.724 .118
.520 .057.118
NS404W
NKY15R
pppp
.625
.375
.625
.375
.625 4.724 .118

.375 4.724 .118

.057.118
.531 .098.118
NS404W
NKY15R
NS404W
NKY15R
pppp
pppp
pppp
pppp
pppp
pppp
GTCT
.591
Dimensions (inch)
R L
GTAHR/L-063S
-083S
GTBHR/L-063S
GTCHR/L-063S
GTAHR/L-063
-083
-103
GTBHR/L-063
-083
-103
GTCHR/L-063
H1
Order Number
Standard Shank
SMALL TOOLS
VT Type
U Type
E Type
L1
F2 Max. Cutting Depth
H2
L1
H3
(Note) Please use right hand insert for right hand holder and left hand insert for left hand holder.
1 If the insert dimension L3 exceeds the holder dimension F2, it is impossible to machine the depths over F2.
2 Clamp Torque (lbf-in) : NS404W=6.2
*
*
INSERTS
D022
Hand
GTAT03006V3R-U
03006V3L-U
05012V5R-U
05012V5L-U
07520V5R-U
07520V5L-U
09520V5R-U
09520V5L-U
10020V5R-U
10020V5L-U
10320V5R-U
12520V5R-U
12520V5L-U
GTBT14530V5R-U
14530V5L-U
15030V5R-U
15030V5L-U
17530V5R-U
17530V5L-U
20030V5R-U
20030V5L-U
GTCT25030V5R-U
25030V5L-U
R
L
R
L
R
L
R
L
R
L
R
R
L
R
L
R
L
R
L
R
L
R
L
(5 inserts in one case)
Dimensions (inch)
Coated
VP15TF
W3
.012
.012
.020
.020
.030
.030
.037
.037
.039
.039
.041
.049
.049
.057
.057
.059
.059
.069
.069
.079
.079
.098
.098
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
L3 *
.024
.024
.047
.047
.079
.079
.079
.079
.079
.079
.079
.079
.079
.118
.118
.118
.118
.118
.118
.118
.118
.118
.118
Re
D1
S1
.001
.001
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.002
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
Geometry
(inch)
U Type Breaker (Grooving)
For general use
20
D1
W3+.002
0
Re
Re
L3
Order Number
S1
INSERTS
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
W3
L3
Re
D1
S1
.013
.013
.017
.017
.021
.021
.030
.030
.037
.037
.039
.039
.039
.039
.047
.047
.047
.047
.055
.055
.059
.059
.059
.059
.071
.071
.079
.079
.079
.079
.089
.089
.098
.098
.108
.108
.118
.118
.013
.017
.021
.026
.030
.031
.033
.037
.039
.043
.047
.051
.055
.059
.079
.024
.024
.047
.047
.047
.047
.079
.079
.079
.079
.079
.079
.079
.079
.079
.079
.079
.079
.079
.079
.118
.118
.118
.118
.118
.118
.118
.118
.118
.118
.118
.118
.118
.118
.118
.118
.118
.118
.024
.047
.079
.079
.079
.079
.079
.079
.079
.079
.079
.079
.079
.118
.118
.001
.001
.001
.001
.002
.002
.002
.002
.002
.002
.002
.002
.004
.004
.002
.002
.004
.004
.002
.002
.002
.002
.004
.004
.002
.002
.002
.002
.004
.004
.002
.002
.002
.002
.002
.002
.002
.002
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
Geometry
E Type Breaker (Grooving)
For precision cutting
20
W3 .001
Re
D1
SMALL TOOLS
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
VP15TF VP15KZ
Re
S1
.010 VT Type Breaker (Grooving, Proling)

.035
.063
.063
W3 .001
14
.063
.063
Re
Re
.063
.063
.063
.063
.063
D1
S1
.063
.063
.106
.106
L3
GTAT03306V3R-E
03306V3L-E
04312V3R-E
04312V3L-E
05312V5R-E
05312V5L-E
07520V5R-E
07520V5L-E
09520V5R-E
09520V5L-E
10020V5R-E
10020V5L-E
1002001R-E
1002001L-E
12020V5R-E
12020V5L-E
1202001R-E
1202001L-E
14020V5R-E
14020V5L-E
GTBT15030V5R-E
15030V5L-E
1503001R-E
1503001L-E
18030V5R-E
18030V5L-E
20030V5R-E
20030V5L-E
2003001R-E
2003001L-E
22530V5R-E
22530V5L-E
GTCT25030V5R-E
25030V5L-E
27530V5R-E
27530V5L-E
30030V5R-E
30030V5L-E
GTAT0330600R-VT
0431200R-VT
0532000R-VT
0652000R-VT
0752000R-VT
0802000R-VT
0852000R-VT
0952000R-VT
1002000R-VT
1102000R-VT
1202000R-VT
1302000R-VT
1402000R-VT
GTBT1503000R-VT
2003000R-VT
Dimensions (inch)
Coated
L3
Hand
Max. Depth of Cut (inch)
Order Number

Work Material
Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF/VP15KZ
165 490
.0004 .0035
VP15TF/VP15KZ
100 590
.0004 .0035
Stainless Steel
VP15TF/VP15KZ
165 395
.0008 .002
Non-Ferrous Metal
VP15TF/VP15KZ
230 755
.0012 .004
SPARE PARTS
M001
TECHNICAL DATA
N001
D023
SMALL TOOLS
GANG TYPE
)
GROOVING TOOLS (FOR
TOOL POSTS
METRIC STANDARD
GTAH, GTBH, GTCH
Long Shank
H2
H3
Stock
s s
s s
Insert Number
s s
s s
s s
GTAT
1
GTBT *
1
GTCT*
GTBT. GTCT
GTCT
s s
GTAT
1
GTBT *
1
GTCT*
H1
H2
L1
F2*
pppp
8
10
8
10
8
10
80
80
2
2
13
13
pppp
12
12
12
80
13
pppp
10
10
10
10
10
10
80
80
3
3
13
13
pppp
8
10
8
10
8
10
120
120
2
2
pppp
pppp
pppp
s s
15
Dimensions (mm)
R L
GTAHR/L0808-20S
1010-20S
1212-20S
GTBHR/L1010-30S
GTCHR/L1010-30S
GTAHR/L0808-20
1010-20
1212-20
1616-20
GTBHR/L1010-30
1212-30
1616-30
GTCHR/L1010-30
H1
Order Number
Standard Shank
SMALL TOOLS
VT Type
U Type
E Type
L1
F2 Max. Cutting Depth
*2
Cutting
Width
(mm)
Insert Screw
Wrench
0.3 3.0
0.3 3.0
0.3 3.0
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
13
13
1.45 3.0
2.5 3.0
0.3 3.0
0.3 3.0
NS404W
NKY15R
NS404W
NKY15R
H3
pppp
12
12
12
120
16
16
16
120
0.3 3.0
0.3 3.0
NKY15R
pppp
13
NS404W
s s
NS404W
NKY15R
a a
pppp
10
10
10
120
13
NS404W
NKY15R
pppp
12
12
12
120
13
1.45 3.0
1.45 3.0
NS404W
NKY15R
a a
pppp
16
10
120
120
3
3
16
13
1.45 3.0
2.5 3.0
NKY15R
pppp
16
10
NS404W
s s
16
10
NS404W
NKY15R
s s
a a
GTBT. GTCT
GTCT
1 If the insert dimension L3 exceeds the holder dimension F2, it is impossible to machine the depths over F2.
2 Clamp Torque (lbf-in) : NS404W=6.2
*
*
INSERTS
D024
Hand
GTAT03006V3R-U
03006V3L-U
05012V5R-U
05012V5L-U
07520V5R-U
07520V5L-U
09520V5R-U
09520V5L-U
10020V5R-U
10020V5L-U
10320V5R-U
12520V5R-U
12520V5L-U
GTBT14530V5R-U
14530V5L-U
15030V5R-U
15030V5L-U
17530V5R-U
17530V5L-U
20030V5R-U
20030V5L-U
GTCT25030V5R-U
25030V5L-U
R
L
R
L
R
L
R
L
R
L
R
R
L
R
L
R
L
R
L
R
L
R
L
Dimensions (mm)
Coated
VP15TF
W3
L3
0.3
0.3
0.5
0.5
0.75
0.75
0.95
0.95
1.0
1.0
1.03
1.25
1.25
1.45
1.45
1.5
1.5
1.75
1.75
2.0
2.0
2.5
2.5
0.6
0.6
1.2
1.2
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*1
Re
D1
S1
0.03
0.03
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
Geometry
(mm)
U Type Breaker (Grooving)
For general use
20
D1
W3+0.05
0
Re
Re
L3
Order Number
S1
INSERTS
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
W3
L3
Re
D1
S1
0.33
0.33
0.43
0.43
0.53
0.53
0.75
0.75
0.95
0.95
1.0
1.0
1.0
1.0
1.2
1.2
1.2
1.2
1.4
1.4
1.5
1.5
1.5
1.5
1.8
1.8
2.0
2.0
2.0
2.0
2.25
2.25
2.5
2.5
2.75
2.75
3.0
3.0
0.33
0.43
0.53
0.65
0.75
0.8
0.85
0.95
1.0
1.1
1.2
1.3
1.4
1.5
2.0
0.6
0.6
1.2
1.2
1.2
1.2
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
0.6
1.2
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
3.0
3.0
0.03
0.03
0.03
0.03
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.1
0.1
0.05
0.05
0.1
0.1
0.05
0.05
0.05
0.05
0.1
0.1
0.05
0.05
0.05
0.05
0.1
0.1
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
Geometry
E Type Breaker (Grooving)
For precision cutting
20
W3 0.025
Re
D1
SMALL TOOLS
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
VP15TF VP15KZ
Re
S1
0.25 VT Type Breaker (Grooving, Proling)

0.9
1.6
1.6
W3 0.025
14
1.6
1.6
Re
Re
1.6
1.6
1.6
1.6
1.6
S1
D1
1.6
1.6
2.7
2.7
L3
GTAT03306V3R-E
03306V3L-E
04312V3R-E
04312V3L-E
05312V5R-E
05312V5L-E
07520V5R-E
07520V5L-E
09520V5R-E
09520V5L-E
10020V5R-E
10020V5L-E
1002001R-E
1002001L-E
12020V5R-E
12020V5L-E
1202001R-E
1202001L-E
14020V5R-E
14020V5L-E
GTBT15030V5R-E
15030V5L-E
1503001R-E
1503001L-E
18030V5R-E
18030V5L-E
20030V5R-E
20030V5L-E
2003001R-E
2003001L-E
22530V5R-E
22530V5L-E
GTCT25030V5R-E
25030V5L-E
27530V5R-E
27530V5L-E
30030V5R-E
30030V5L-E
GTAT0330600R-VT
0431200R-VT
0532000R-VT
0652000R-VT
0752000R-VT
0802000R-VT
0852000R-VT
0952000R-VT
1002000R-VT
1102000R-VT
1202000R-VT
1302000R-VT
1402000R-VT
GTBT1503000R-VT
2003000R-VT
Dimensions (mm)
Coated
L3
Hand
Max. Depth of Cut (mm)
Order Number

Work Material
Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF/VP15KZ
165 490
.0004 .0035
VP15TF/VP15KZ
100 590
.0004 .0035
Stainless Steel
VP15TF/VP15KZ
165 395
.0008 .002
Non-Ferrous Metal
VP15TF/VP15KZ
230 755
.0012 .004
SPARE PARTS
M001
TECHNICAL DATA
N001
D025
SMALL TOOLS
GANG TYPE
)
CUTTING OFF TOOLS (FOR
TOOL POSTS
INCH STANDARD
CTAH
L1
.217
H1
H2
H3
SMALL TOOLS
D1
Order Number
Stock
.866
.591
Dimensions (inch)
Insert Number
R L
CTAHR/L-062
a a
-082
a a
-102
a a
pppp
CTAT
H1
H2
L1
H3
.375
.375
.375
4.724
.500
pppp
.500
.500
.500
4.724
pppp
.625
.625
.625
4.724
Max.
*2
Cut Off
Diameter
(inch)
Insert Screw Wrench
D1
NS402W
NKY15R
.472
(.315) 1 NS403W
*
NKY15R
NS403W
NKY15R
the width of cutting off is .028inch.

*12 When
*
CTAH-S
L1
.217
.630
45
D1
Order Number
Stock
H1
H2
H3
.217
*
*
-082S
Dimensions (inch)
Insert Number
CTAHR-062S
.591
CTAT
H1
H2
L1
H3
pppp
.375
.375
.375
3.150
.500
pppp
.500
.500
.500
3.150
Max.
*2
Cut Off
Diameter
(inch)
Insert Screw Wrench
D1
.472
(.315) 1
NS401
NKY25R
NS401
NKY25R
1 When the width of cutting off is .028inch.

2 Clamp Torque (lbf-in) : NS401=31

Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF
165 490
.0008 .0035
VP15TF
100 590
.0004 .0035
Stainless Steel
VP15TF
165 395
.0008 .0019
Non-Ferrous Metal
VP15TF
230 755
.0012 .0043
Work Material
D026
Geometry
Insert Geometry
16
16
Without Breaker
With Breaker
16
20
Without Breaker
Left Hand (L)
16
CTAT07080V5RR-B
10120V5RR-B
15120V5RR-B
20120V5RR-B
CTAT15120V5RR-BX
20120V5RR-BX
R
R
R
R
R
R
CTAT10120V5RN-B
15120V5RN-B
20120V5RN-B
N
N
N
CTAT15120V5RN-BX
20120V5RN-BX
N
N
CTAT10110V5RL-B
15110V5RL-B
20110V5RL-B
L
L
L
CTAT1012000RR
1512000RR
2012000RR
R
R
R
CTAT07080V5LL-B
10120V5LL-B
15120V5LL-B
20120V5LL-B
CTAT10120V5LN-B
15120V5LN-B
20120V5LN-B
L
L
L
L
N
N
N
CTAT10110V5LR-B
15110V5LR-B
20110V5LR-B
R
R
R
CTAT1012000LL
1512000LL
2012000LL
L
L
L
a
a
a
.028
.039
.059
.079
.177
.264
.264
.264
.002
.002
.002
.002
.315
.472
.472
.472
.059 .264 .002

.079 .264 .002
.472
.472
.039 .264 .002

.059 .264 .002
.079 .264 .002
.472
.472
.472
.059 .264 .002

.079 .264 .002
.472
.472
.039 .264 .002

.059 .264 .002
.079 .264 .002
.433
.433
.433
.039 .264 0
.059 .264 0
.079 .264 0
.472
.472
.472
.028
.039
.059
.079
.002
.002
.002
.002
.315
.472
.472
.472
.039 .264 .002

.059 .264 .002
.079 .264 .002
.472
.472
.472
.039 .264 .002

.059 .264 .002
.079 .264 .002
.433
.433
.433
.039 .264 0
.059 .264 0
.079 .264 0
.472
.472
.472
Strong Edge Type
16
20
Hand
Strong Edge Type
With Breaker
Right Hand (R)
Coated Dimensions (inch) Max. Cut Off

Diameter
VP15TF W3 L3
Re
(inch)
Order Number
SMALL TOOLS
Setting Geometry
Breaker
Holder
INSERTS
a
a
a
a
a
a
a
a
a
a
a
a
a
.177
.264
.264
.264
SPARE PARTS
M001
TECHNICAL DATA
N001
D027
SMALL TOOLS
GANG TYPE
)
TOOL POSTS
METRIC STANDARD
CTAH
L1
5.5
H1
H2
H3
SMALL TOOLS
Stock
15
D1
Order Number
22
Dimensions (mm)
Insert Number
R L
H1
H2
L1
H3
CTAHR/L0810-120
a a
pppp
10
120
12
1010-120
a a
pppp
10
10
10
120
12
1212-120
a a
pppp
12
12
12
120
1616-120
a a
pppp
16
16
16
120
CTAT
Max.
*2
Cut Off
Diameter
(mm)
Insert Screw Wrench
D1
12
(8 )
*1
NS402W
NKY15R
NS402W
NKY15R
NS403W
NKY15R
NS403W
NKY15R
the width of cutting off is 0.7mm.

*12 When
*
CTAH-S
L1
5.5
16
45
H1
H2
H3
5.5
Order Number
Stock
Dimensions (mm)
Insert Number
CTAHR1010-120S
15
D1
CTAT
pppp
H1
H2
L1
H3
10
10
10
80
12
Max.
*2
Cut Off
Diameter
(mm)
Insert Screw Wrench
D1
12
(8 )
*1
NS401
the width of cutting off is 0.7mm.

*12 When
Clamp Torque (lbf-in) : NS401=31
*

Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF
165 490
.0008 .0035
VP15TF
100 590
.0004 .0035
Stainless Steel
VP15TF
165 395
.0008 .0019
Non-Ferrous Metal
VP15TF
230 755
.0012 .0043
Work Material
D028
NKY25R
Geometry
Insert Geometry
16
16
Without Breaker
With Breaker
16
20
Without Breaker
Left Hand (L)
16
CTAT07080V5RR-B
10120V5RR-B
15120V5RR-B
20120V5RR-B
CTAT15120V5RR-BX
20120V5RR-BX
R
R
R
R
R
R
CTAT10120V5RN-B
15120V5RN-B
20120V5RN-B
N
N
N
CTAT15120V5RN-BX
20120V5RN-BX
N
N
CTAT10110V5RL-B
15110V5RL-B
20110V5RL-B
L
L
L
CTAT1012000RR
1512000RR
2012000RR
R
R
R
CTAT07080V5LL-B
10120V5LL-B
15120V5LL-B
20120V5LL-B
CTAT10120V5LN-B
15120V5LN-B
20120V5LN-B
L
L
L
L
N
N
N
CTAT10110V5LR-B
15110V5LR-B
20110V5LR-B
R
R
R
CTAT1012000LL
1512000LL
2012000LL
L
L
L
a
a
a
0.7
1.0
1.5
2.0
4.5
6.7
6.7
6.7
0.05
0.05
0.05
0.05
8
12
12
12
1.5
2.0
6.7 0.05
6.7 0.05
12
12
1.0
1.5
2.0
6.7 0.05
6.7 0.05
6.7 0.05
12
12
12
1.5
2.0
6.7 0.05
6.7 0.05
12
12
1.0
1.5
2.0
6.7 0.05
6.7 0.05
6.7 0.05
11
11
11
1.0
1.5
2.0
6.7 0
6.7 0
6.7 0
12
12
12
0.7
1.0
1.5
2.0
4.5
6.7
6.7
6.7
0.05
0.05
0.05
0.05
8
12
12
12
1.0
1.5
2.0
6.7 0.05
6.7 0.05
6.7 0.05
12
12
12
1.0
1.5
2.0
6.7 0.05
6.7 0.05
6.7 0.05
11
11
11
1.0
1.5
2.0
6.7 0
6.7 0
6.7 0
12
12
12
Strong Edge Type
16
20
Hand
Strong Edge Type
With Breaker
Right Hand (R)
Coated Dimensions (mm) Max. Cut Off

Diameter
VP15TF W3 L3
Re
(mm)
Order Number
SMALL TOOLS
Setting Geometry
Breaker
Holder
INSERTS
a
a
a
a
a
a
a
a
a
a
a
a
a
SPARE PARTS
M001
TECHNICAL DATA
N001
D029
SMALL TOOLS
GANG TYPE
)
TOOL POSTS
INCH STANDARD
CTBH
L1
.295
SMALL TOOLS
D1
Stock
Order Number
a a
-082
a a
-102
a a
.768
CTBT
Max.
Cut Off
Diameter
(inch)
Insert Screw
D1
Dimensions (inch)
Insert Number
R L
CTBHR/L-062
H1
H3
H2
.984
Wrench
H1
H2
L1
H3
pppp
.375
.375
.375
4.724
.500
.630
NS402W
NKY15R
pppp
.500
.500
.500
4.724
.630
NS403W
NKY15R
pppp
.625
.625
.625
4.724
.630
NS403W
NKY15R
* Clamp Torque (lbf-in) : NS402W=6.2, NS403W=6.2
Setting Geometry
Breaker
Holder
INSERTS
Geometry
Insert Geometry
W3 .002
.362
Hand
CTBT15160V5RR-B
.059
.002
.630
20160V5RR-B
.079
.002
.630
CTBT20160V5RN-B
.079
.002
.630
CTBT20160V5LL-B
.079
.002
.630
CTBT20160V5LN-B
.079
.002
.630
CTBT20145V5LR-B
.079
.002
.571
VP15TF
Re
16
Re
0
.362
W3 .002
Right Hand (R)
Re
Coated Dimensions (inch) Max. Cut Off

Diameter
W3
Re
(inch)
Order Number
Re
W3 .002
With Breaker
Re
Re
.362
Re
W3 .002
Left Hand (L)
16
Re
.362
W3 .002
Re
16
Re
D030
.362
METRIC STANDARD
CTBH
L1
7.5
Stock
Order Number
a a
1212-160
a a
1616-160
a a
CTBT
Max.
Cut Off
Diameter
(mm)
Insert Screw
D1
Dimensions (mm)
Insert Number
R L
CTBHR/L1010-160
19.5
H1
H2
L1
H3
pppp
10
10
10
120
12
pppp
12
12
12
120
pppp
16
16
16
120
Wrench
16
NS402W
NKY15R
16
NS403W
NKY15R
16
NS403W
NKY15R
SMALL TOOLS
D1
H1
H3
H2
25

Setting Geometry
Breaker
Holder
INSERTS
Geometry
Insert Geometry
Re
Re
9.2
Hand
CTBT15160V5RR-B
1.5
0.05
16
20160V5RR-B
2.0
0.05
16
CTBT20160V5RN-B
2.0
0.05
16
CTBT20160V5LL-B
2.0
0.05
16
CTBT20160V5LN-B
2.0
0.05
16
CTBT20145V5LR-B
2.0
0.05
14.5
W3 0.05
Re
Re
W3 0.05
16
Re
9.2
Re
W3 0.05
Left Hand (L)
9.2
W3 0.05
16
With Breaker
Right Hand (R)
Re
Coated Dimensions (mm) Max. Cut Off

Diameter
(mm)
VP15TF W3
Re
Order Number
Re
9.2
W3 0.05
Re
16
Re
9.2

Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF
165 490
.0008 .0035
VP15TF
100 590
.0004 .0035
Stainless Steel
VP15TF
165 395
.0008 .0019
Non-Ferrous Metal
VP15TF
230 755
.0012 .0043
Work Material
SPARE PARTS
M001
TECHNICAL DATA
N001
D031
SMALL TOOLS
GANG TYPE
)
TOOL POSTS
METRIC STANDARD
CTCH
L1
W3
F2
0.5
H1
SMALL TOOLS
H2
Order Number
Stock
R L
CTCHR/L1010-200
a a
1212-200
a a
CTCT
Dimensions (mm)
Insert Number
Max.
Cut Off
Diameter
(mm)
D1 Clamp Screw
Wrench
H1
H2
L1
F2
2ppp
10
10
10
120
11
20
NS501W HKY25RS
2ppp
12
12
12
120
11
20
NS501W HKY25RS
* Clamp Torque (lbf-in) : NS501W=19
With Breaker
Breaker
INSERTS
D032
Dimensions (mm)
Re
Max.Cut Off
Diameter
(mm)
0.05
20
2.2
0.1
20
2.5
0.05
20
2.5
0.1
20
22200V5R-B
2.2
17
0.05
20
2220001R-B
2.2
17
0.1
20
25200V5R-B
2.5
17
0.05
20
2520001R-B
2.5
17
0.1
20
22200V5L-B
2.2
17
0.05
20
2220001L-B
2.2
17
0.1
20
25200V5L-B
2.5
17
0.05
20
2520001L-B
2.5
17
0.1
20
Order Number
Hand
CTCT22200V5N-B
Coated
VP15TF
W3
B9
2.2
2220001N-B
25200V5N-B
2520001N-B
Geometry
Neutral (N)
Right Hand (R)
Left Hand (L)
METRIC STANDARD
CTDH
L1
L2
0.5
W3
F2
0.5
Stock
Dimensions (mm)
Insert Number
R L
Max.
Cut Off
Diameter
(mm)
D1 Clamp Screw
H1
H2
L1
L2
F2
Wrench
CTDHR/L1616-230
2535pp
16
16
16
125
24
12.2
23
HBH06020 HKY40R
1616-280
2535pp
16
16
16
120
25
15
28
NS502W
1616-350
a a
2535pp
16
16
16
125
32
18.5
35
HBH06020 HKY40R
CTDT
SMALL TOOLS
Order Number
H1
H2
HKY25R
* Clamp Torque (lbf-in) : HBH06020=62, NS502W=19
With Breaker
Order Number
Hand
Dimensions (mm)
VP15TF
W3
B9
Re
Max. Cut Off

Diameter
(mm)
0.2
23 35
Coated
CTDT2535002N-B
2.5
25350V5R-B
2.5
<
0.05
23 35
25350V5R-BS
2.5
17
<
0.05
23 35
2535002R-B
2.5
0.2
23 35
Geometry
6.39
W3 0.05
Breaker
INSERTS
90
Re
12
Re
B9
Neutral (N)
Right Hand (R)

Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF
165 490
.0008 .0035
VP15TF
100 590
.0004 .0035
Stainless Steel
VP15TF
165 395
.0008 .0019
Non-Ferrous Metal
VP15TF
230 755
.0012 .0043
Work Material
SPARE PARTS
M001
TECHNICAL DATA
N001
D033
SMALL TOOLS
GANG TYPE
)
TOOL POSTS
METRIC STANDARD
CTEH
L1
L2
0.5
W3
F2
0.5
H1
H2
SMALL TOOLS
Order Number
Stock
Dimensions (mm)
Insert Number
R L
Max.
Cut Off
Diameter
(mm)
D1 Clamp Screw
Wrench
H1
H2
L1
L2
F2
12.2
23
HBH06020 HKY40R
CTEHR/L1616-230
3035pp
16
16
16
125
24
1616-280
3035pp
16
16
16
120
25
15
28
NS502W
1616-350
a a
3035pp
16
16
16
125
32
18.5
35
HBH06020 HKY40R
CTET
HKY25R
* Clamp Torque (lbf-in) : HBH06020=62, NS502W=19
Order Number
Dimensions (mm)
Coated
B9
Re
Max. Cut Off

Diameter
(mm)
VP15TF
W3
<
0.05
23 35
30350V5R-BS
17
<
0.05
23 35
3035002N-B
0.2
23 35
3035002R-B
0.2
23 35
3035002L-B
0.2
23 35
CTET30350V5R-B
With Breaker
Hand
Geometry
6.39
90
Re
W3 0.05
Breaker
INSERTS
12
Re
B 9
B 9
Neutral (N) Right Hand (R) Left Hand (L)

Grade
Cutting Speed (SFM)
VP15TF
165 490
.0008 .0035
VP15TF
100 590
.0004 .0035
Stainless Steel
VP15TF
165 395
.0008 .0019
Non-Ferrous Metal
VP15TF
230 755
.0012 .0043
Work Material
D034
Feed (IPR)
GANG TYPE
)
THREADING TOOLS (FOR
TOOL POSTS
INCH STANDARD
TTAH
L1
.276
.591
Order Number
Stock
H1
H2
L1
H3
Insert Screw
Wrench
.375
.500
.625
.375
.500
.625
.375
.500
.625
4.724
4.724
4.724
.500

NS402W
NS402W
NS402W
NKY15R
NKY15R
NKY15R
Coated Dimensions (inch)
Pitch of
Thread (inch)
(thread/inch)
R L
TTAHR/L-062
-082
-102
pppp
a a
a a
pppp
TTAT
pppp
a a
Dimensions (inch)
Insert Number
SMALL TOOLS
H1
H2
H3
.256 Max. Step Difference
Clamp Torque (lbf-in) : NS402W=6.2
Z2
Re
TTAT60075F5RR-B
.016
60125V5RR-B
.031
.002 .020 .049
60075F5RL-B
.016
.002 .008 .030

Flat
60125V5RL-B
.031
.002 .020 .049
6015001RN-B
.049
.004 .039 .059
60075F5LR-B
.016
.002 .008 .030

Flat
60125V5LR-B
.031
.002 .020 .049
60075F5LL-B
.016
.002 .008 .030

Flat
60125V5LL-B
.031
.002 .020 .049
6015001LN-B
.049
.004 .039 .059
55158V5RR-B
.031
.002
(40 16)
55158V5RL-B
.031
.002
(40 16)
55158V5LR-B
.031
.002
(40 16)
55158V5LL-B
.031
.002
(40 16)
60
Z2
60
Z2
Right Hand (R)
Z2
60
.098
Re
Re
Z2
60
.315
With Breaker
50
Re
60
Z2
60
Re
Z2
Left Hand (L)
VP15TF
.002 .008 .030

Flat
Re
.787
Re
Re
Z2
Z2
.098
General Purpose
(55)
.787
Re
Re
Z2
Z2
.315
Left Hand (L) Right Hand (R)
Hand
55
General Purpose
(60)
Order Number
55
Insert Geometry
55
Geometry
55
Setting Geometry
Breaker
Holder
INSERTS
50
Re
Refer to page D037 for the thread diameter range.

P
Work Material
Cutting Speed (SFM)

165 490
100 590
M
N
Work Material
Stainless Steel
Non-Ferrous Metal
Cutting Speed (SFM)

165 395
230 755
SPARE PARTS
M001
TECHNICAL DATA
N001
D035
SMALL TOOLS
GANG TYPE
)
TOOL POSTS
METRIC STANDARD
TTAH
L1
B
SMALL TOOLS
H1
H2
H3
6.5 Max. Step Difference
15
Order Number
Stock
Dimensions (inch)
Insert Number
H1
H2
L1
H3
Insert Screw
Wrench
pppp
10
120
12
NS402W
NKY15R
pppp
10
10
10
120
12
NS402W
NKY15R
a a
pppp
12
12
12
120
NS403W
NKY15R
a a
pppp
16
16
16
120
NS403W
NKY15R
Coated Dimensions (mm)

Re
Pitch of
Thread (mm)
(thread/inch)
R L
TTAHR/L0810
a a
1010
a a
1212
1616
TTAT

Order Number
Hand
TTAT60075F5RR-B
0.4
0.05
Flat
0.2 0.75
(80 36)
60125V5RR-B
0.8
0.05
0.5 1.25
(40 16)
60075F5RL-B
0.4
0.05
Flat
0.2 0.75
(80 36)
60125V5RL-B
0.8
0.05
0.5 1.25
(40 16)
6015001RN-B
1.25
0.1
1.0 1.5
(24 18)
60075F5LR-B
0.4
0.05
Flat
0.2 0.75
(80 36)
60125V5LR-B
0.8
0.05
0.5 1.25
(40 16)
60075F5LL-B
0.4
0.05
Flat
0.2 0.75
(80 36)
60125V5LL-B
0.8
0.05
0.5 1.25
(40 16)
60
6015001LN-B
1.25
0.1
1.0 1.5
(24 18)
55
55158V5RR-B
0.8
0.05
(40 16)
55
55158V5RL-B
0.8
0.05
(40 16)
55
Geometry
55158V5LR-B
0.8
0.05
(40 16)
55
Setting Geometry
Breaker
Holder
INSERTS
Insert Geometry
55158V5LL-B
0.8
0.05
(40 16)
Z2
Right Hand (R)
VP15TF
Z2
60
General Purpose
(60)
60
Z2
Re
Z2
60
2.5
Re
20.0
Z2
Re
60
Z2
Left Hand (L)
With Breaker
50
60
8.0
Re
Z2
Re
Re
Z2
Re
Z2
2.5
Left Hand (L) Right Hand (R)
General Purpose
(55)
Re
20.0
50
Z2
Z2
8.0
Re
Refer to page D037 for the thread diameter range.
D036
Re
HOLDER APPLICATION
Left Hand Holder + Left Hand Insert
B Type Insert
SMALL TOOLS
A Type Insert
Right Hand Holder + Right Hand Insert
* Above 4 combinations enable machining at the areas shown by p.

THREAD DIAMETER RANGE
Pitch
(mm)
> & 1.0
0.2
0.25
0.3
0.35
0.4
0.45
0.5
0.6
0.7
0.75
0.8
1
1.25
1.5
Metric Thread (60)
> & 1.2
> & 1.6
Application Range
> & 2.0
Thread Diameter (mm)

> & 2.5
> & 3.0
> & 4.0
> & 5.0
> & 6.0
> & 7.0
Number of
Passes
24
35
46
57
Machining
Impossible
68
Pitch(thread/inch)
Thread Diameter
Inch
mm
80
72
64
56
48
44
40
32
28
26
24
20
18
16
> & 0.060 > & 0.073 > & 0.086 > & 0.099 > & 0.112 > & 0.164 > & 0.190 > & 0.250 > & 0.313
> & 1.524 > & 1.854 > & 2.184 > & 2.515 > & 2.845 > & 4.166 > & 4.826 > & 6.350 > & 7.938
Number of
Passes
35
46
57
Machining
Impossible
68
*American UN,Whitworth Thread

Work Material
Cutting Speed (SFM)
Work Material
Cutting Speed (SFM)
165 490
Stainless Steel
165 395
100 590
Non-Ferrous Metal
230 755
SPARE PARTS
M001
TECHNICAL DATA
N001
D037
SMALL TOOLS
GANG TYPE
)
TOOL POSTS
INCH STANDARD
F1
S1
MMTE
1.5
10
H2
L2
Order Number
Stock
MMTER-063SM
-083SM
H1
TTAT
MMT16ER
ppppp
L1
L2
H1
H2
MMTER-063SM
Dimensions (inch)
Insert Number
H2
H1
10
H2
SMALL TOOLS
10
.118"
3.0
L1
F1
x
S1 Clamp Bridge Clamp Screw Stop Ring Shim Screw Shim Wrench
.375 .375 4.724 .875 .375 .625
SETK51 SETS51
CR4
HFC03008 CTE32TP15
zTKY15F
xHKY20R
.500 .500 4.724 .875 .500 .625
SETK51 SETS51
CR4
HFC03008 CTE32TP15
zTKY15F
xHKY20R
* Clamp Torque (lbf-in) : SETS51=31, HFC03008=18
D038
MMTE type inserts
G014 G020
HOW TO SELECT A SHIM
G025
OPPOSITE
DIMPLE SLEEVE HOLDER (FOR
TOOL POSTS )
INCH STANDARD
Finish
SMG
Finish
Light
R-SS
R-F
Medium
R-SN
(2,3)
(2,3)
(2,3)
Medium
Flat Top
(2,3)

AZ
R-SR
93
Order Number
Stock
Left hand tool holder only.
SH16H-FSDUCL07
19K-FSDUCL07
25M-FSDUCL07
SH16H-FSDUCL11
19K-FSDUCL11
25M-FSDUCL11
(2,3)
(2,3)
Insert Screw
Wrench
.625 3.937 .787 .551 .305 .165 .030
TS254
TKY08R
D4
21.5pp
32.5pp
(2,3)
Dimensions (inch)
Insert Number
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
(2,3)
L1
L2
H1
F1
S1
F2
.750 4.921 .787 .669 .364 .165 .030
TS254
TKY08R
1.000 5.906 .787 .906 .482 .165 .030
TS254
TKY08R
.625 3.937 .787 .551 .305 .252 .030
TS43
TKY15R
.750 4.921 .787 .669 .364 .252 .030
TS43
TKY15R
1.000 5.906 .787 .906 .482 .252 .030
TS43
TKY15R
SMALL TOOLS
SH
(Note 1) When using insert with right and left hand chip breaker, please use right hand insert.
(Note 2) Insert photo is an example. Letters show chip breaker style, gures show inscribed circle.
SHppp type inserts
A109 A113
SPARE PARTS
M001
CBN & PCD inserts
B042, B043, B059
TECHNICAL DATA
N001
D039
SMALL TOOLS
OPPOSITE
DIMPLE SLEEVE HOLDER (FOR
TOOL POSTS )
METRIC STANDARD
SH
Finish
SMG
Finish
Light
Medium
R-SS
R-F
R-SN
(2,3)
(2,3)
(2,3)
Medium
Flat Top
(2,3)

AZ
R-SR
SMALL TOOLS
93
Order Number
Stock
SH20K-FSDUCL07
22K-FSDUCL07
SH20K-FSDUCL11
22K-FSDUCL11
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
21.5pp
32.5pp
(2,3)
(2,3)
(2,3)
Dimensions (mm)
Insert Number
(2,3)
D4
L1
L2
H1
F1
S1
F2
Insert Screw
Wrench
20
125
20
18
9.75
4.2
0.75
TS254
TKY08R
22
125
20
20
10.75
4.2
0.75
TS254
TKY08R
20
125
20
18
9.75
6.4
0.75
TS43
TKY15R
22
125
20
20
10.75
6.4
0.75
TS43
TKY15R
(Note 1) When using insert with right and left hand chip breaker, please use right hand insert.
(Note 2) Insert photo is an example. Letters show chip breaker style, gures show inscribed circle.

Work Material
Grade
Cutting Speed (SFM)
Feed (IPR)
VP15TF
165 490
.0004 .006
VP15TF
100 590
.0004 .006
AP25N
165 820
.0004 .006
Free Cutting Steel
D040
Stainless Steel
VP15TF
165 395
.0008 .004
Non-Ferrous Metal
HTi10
230 755
.0012 .006
SHppp type inserts
A109 A113
CBN & PCD inserts
B042, B043, B059
FOR RADIAL TYPE TOOL POSTS

INCH STANDARD
Stock
Order Number
Dimensions (inch)
Insert Number
R L
CSVHR/L-062
a a
CSVT
-082
H1
H2
L1
L9
pppp
.375
.375
.375
5.512
pppp
.500
.500
.500
5.512
Max.
D.O.C
(inch)
Insert Screw
Wrench
.118
NS251
NKY15R
.118
NS251
NKY15R
SMALL TOOLS
CSVH
(Note 2) Each insert has own depth of cut.
INSERTS
CSVTF
D1
S1
Re
S2
B3
CSVTF30AR
30AL
.250
.094
.012
.118
.250
.094
.012
.118
30BR
.250
.094
.012
.118
30CR
.250
.094
.006
.118
30DR
.250
.094
.006
.118
CSVTF30AR-B
.250
.094
.012
.118
30AL-B
.250
.094
.012
.118
30BR-B
.250
.094
.012
.118
30CR-B
30DR-B
.250
.094
.006
.118
.250
.094
.006
.118
CSVTFXL
Order Number
Hand
CSVTFXL
Geometry
Without Breaker
Re
S2
VP15KZ
Max.
D.O.C
(inch)
Dimensions (inch)
Coated
D1
B3
30
S1
With Breaker
Re
7
D1
S1
S2
Hand
B3
30
(Front turning, Copying)
VP15KZ
D1
S1
Re
Max.
D.O.C
(inch)
.250
.094
.118
Dimensions (inch)
Coated
Geometry
Without Breaker
Re
80
.028
Order Number
(Front turning)
D1
S1
45
SPARE PARTS
M001
TECHNICAL DATA
N001
D041
SMALL TOOLS

INSERTS
(Cutting off)
CSVTC0640R
0750R
0750L
0850R
0850L
0950R
1060R
1060L
1360R
1360L
1560R
1560L
CSVTC0640R-B
0750R-B
0850R-B
0950R-B
1060R-B
1360R-B
1560R-B
R
R
L
R
L
R
R
L
R
L
R
L
R
R
R
R
R
R
R
VP15KZ
D1
S1
Re
L3
W3
Max.
D.O.C.
(inch)
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
.079
.098
.098
.098
.098
.098
.118
.118
.118
.118
.118
.118
.079
.098
.098
.098
.118
.118
.118
.024
.028
.028
.031
.031
.035
.039
.039
.051
.051
.059
.059
.024
.028
.031
.035
.039
.051
.059
.059
.079
.079
.079
.079
.079
.098
.098
.098
.098
.098
.098
.059
.079
.079
.035
.098
.098
.098
Dimensions (inch)
Coated
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CSVTB
Geometry
Without Breaker
25
7
D1
25
7
D1
S1
Re
L3
(Back turning)
D1
S1
Re
L3
W3
S2
B9
R
R
R
R
R
R
R
R
R
R
R
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
.094
0
0
0
0
0
0
0
0
0
0
0
0
0
.098
.098
.098
.098
.098
.098
.098
.098
.098
.098
.098
.098
.098
.039
.039
.039
.039
.039
.047
.055
.039
.039
.039
.039
.047
.055
.012
.012
.012
.006
.006
.012
.012
.012
.012
.006
.006
.012
.012
5
5
2
2
5
5
5
5
2
2
5
5
5
.079 Without Breaker

.079
.079
.079
.079
D1
.079
.079
.079 With Breaker
.079
.079
.079
.079
D1
.079
a
a
a
a
a
a
a
a
a
a
CSVTBXL
Order Number
Hand
CSVTBXL
W3 .002
Geometry
S2
45 B9
7
L3
S1
Re
45 B9
7
L3
S1
Re
(Back turning, Copying)
VP15KZ
D1
S1
Re
Max.
D.O.C
(inch)
.250
.094
.118
Dimensions (inch)
Coated
Geometry
Without Breaker
Oversize 45
S1
5
D042
.0014
Re
7
D1
W3 .002
Dimensions (inch)
Coated
S2
CSVTB10AR
10AL
10BR
10CR
10DR
12AR
14AR
CSVTB10AR-B
10BR-B
10CR-B
10DR-B
12AR-B
14AR-B
Re
L3
VP15KZ
Hand
S1
With Breaker
Max.
D.O.C.
(inch)
Order Number
W3 .002
Hand
W3 .002
Order Number
.028
SMALL TOOLS
CSVTC
INSERTS
(Grooving)
D1
S1
Re
L3
W3
Max.
D.O.C.
(inch)
.250
.094
.020
.010
.006
.250
.094
.020
.012
.006
.250
.094
.020
.014
.006
.250
.094
.020
.016
.006
.250
.094
.039
.018
.018
.250
.094
.039
.020
.018
.250
.094
.039
.022
.018
.250
.094
.039
.024
.018
.250
.094
.039
.026
.018
.250
.094
.039
.028
.018
.250
.094
.079
.030
.055
.250
.094
.079
.030
.055
.250
.094
.079
.031
.055
.250
.094
.079
.033
.055
.250
.094
.079
.035
.055
.250
.094
.079
.037
.055
.250
.094
.079
.037
.055
.250
.094
.079
.039
.055
.250
.094
.118
.043
.102
.250
.094
.118
.047
.102
.250
.094
.118
.047
.102
.250
.094
.118
.051
.102
.250
.094
.118
.055
.102
.250
.094
.118
.059
.102
Hand
CSVTG02505R
03005R
03505R
04005R
04510R
05010R
05510R
06010R
06510R
07010R
07520R
07520L
08020R
08520R
09020R
09520R
09520L
10020R
11030R
12030R
12030L
13030R
14030R
15030R
CSVTT
Dimensions (inch)
Coated
Geometry
Without Breaker
SMALL TOOLS
VP15KZ
Order Number
W3 +.0012
+0
CSVTG
7
Re
S1
D1
L3
(Threading)
Dimensions (inch)
S1
Re
.008.020
.250
.094
.001
.008.020
.250
.094
.001
CSVTT60050RR
60050RL
Geometry
Without Breaker
General Purpose (60)
RR
60
.014 .002
D1
RL
60
.118 Re
.039
1.0
VP15KZ
Hand
.014 .002
.039
1.0
Coated
Pitch
(inch)
Order Number
.118 Re
SPARE PARTS
M001
TECHNICAL DATA
N001
D043
SMALL TOOLS

METRIC STANDARD
SMALL TOOLS
CSVH
Stock
Order Number
Dimensions (mm)
Insert Number
R L
H1
H2
L1
L9
Max.
D.O.C
(mm)
Insert Screw
Wrench
CSVHR/L0707
a a
pppp
140
0.5
3.0
NS251
NKY15R
0808
a a
pppp
140
3.0
NS251
NKY15R
0909
pppp
9.5
9.5
9.5
140
3.0
NS251
NKY15R
1010
a a
pppp
10
10
10
140
3.0
NS251
NKY15R
1212
pppp
12
12
12
140
3.0
NS251
NKY15R
CSVT
(Note 2) Each insert has own depth of cut.
INSERTS
CSVTF
S2
B3
Max.
D.O.C
(mm)
Dimensions (mm)
Coated
VP15KZ
D1
S1
Re
CSVTF30AR
30AL
6.35
2.38
0.3
3.0
6.35
2.38
0.3
3.0
30BR
6.35
2.38
0.3
3.0
30CR
6.35
2.38
0.15
3.0
30DR
6.35
2.38
0.15
3.0
CSVTF30AR-B
6.35
2.38
0.3
3.0
30AL-B
6.35
2.38
0.3
3.0
30BR-B
6.35
2.38
0.3
3.0
30CR-B
30DR-B
6.35
2.38
0.15
3.0
6.35
2.38
0.15
3.0
CSVTFXL
Order Number
Hand
CSVTFXL
Geometry
Without Breaker
Re
7
D1
S2
Hand
B3
30
S1
With Breaker
Re
7
D1
S1
S2
Order Number
(Front turning)
B3
30
(Front turning, Copying)
VP15KZ
D1
S1
Re
Max.
D.O.C
(mm)
6.35
2.38
3.0
Dimensions (mm)
Coated
Geometry
Without Breaker
Re
0.7
80
7
D1
S1
45
D044
INSERTS
CSVTC
(Cutting off)
R
R
L
R
L
R
R
L
R
L
R
L
R
R
R
R
R
R
R
D1
S1
Re
L3
W3
Max.
D.O.C
(mm)
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2.0
2.5
2.5
2.5
2.5
2.5
3.0
3.0
3.0
3.0
3.0
3.0
2.0
2.5
2.5
2.5
3.0
3.0
3.0
0.6
0.7
0.7
0.8
0.8
0.9
1.0
1.0
1.3
1.3
1.5
1.5
0.6
0.7
0.8
0.9
1.0
1.3
1.5
1.5
2.0
2.0
2.0
2.0
2.0
2.5
2.5
2.5
2.5
2.5
2.5
1.5
2.0
2.0
0.9
2.5
2.5
2.5
Dimensions (mm)
Coated
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CSVTB
7
D1
S1
Re
L3
With Breaker
25
7
D1
S1
Re
L3
L3
W3
S2
B9
R
R
R
R
R
R
R
R
R
R
R
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
6.35
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
2.38
0
0
0
0
0
0
0
0
0
0
0
0
0
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
1
1
1
1
1
1.2
1.4
1
1
1
1
1.2
1.4
0.3
0.3
0.3
0.15
0.15
0.3
0.3
0.3
0.3
0.15
0.15
0.3
0.3
5
5
2
2
5
5
5
5
2
2
5
5
5
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
a
a
a
a
a
a
a
a
CSVTBXL
Order Number
Hand
CSVTBXL
45 B9
7
D1
L3
S1
Re
With Breaker
45 B9
7
D1
L3
S1
Re
(Back turning, Copying)
VP15KZ
D1
S1
Re
Max.
D.O.C
(mm)
6.35
2.38
3.0
Dimensions (mm)
Coated
Geometry
Without Breaker
0.7
Without Breaker
Oversize 45
Re
7
D1
S1
5
0.035
Geometry
W3 0.05
Re
S2
S1
Dimensions (mm)
Coated
W3 0.05
D1
CSVTB10AR
10AL
10BR
10CR
10DR
12AR
14AR
CSVTB10AR-B
10BR-B
10CR-B
10DR-B
12AR-B
14AR-B
25
S2
VP15KZ
Hand
Without Breaker
(Back turning)
Max.
D.O.C
(mm)
Order Number
Geometry
SMALL TOOLS
CSVTC0640R
0750R
0750L
0850R
0850L
0950R
1060R
1060L
1360R
1360L
1560R
1560L
CSVTC0640R-B
0750R-B
0850R-B
0950R-B
1060R-B
1360R-B
1560R-B
VP15KZ
W3 0.05
Hand
W3 0.05
Order Number
SPARE PARTS
M001
TECHNICAL DATA
N001
D045
SMALL TOOLS

INSERTS
(Grooving)
Max.
D.O.C
(mm)
0.5
0.25
0.15
0.5
0.3
0.15
0.5
0.35
0.15
0.5
0.4
0.15
1.0
0.45
0.45
2.38
1.0
0.5
0.45
2.38
1.0
0.55
0.45
6.35
2.38
1.0
0.6
0.45
6.35
2.38
1.0
0.65
0.45
6.35
2.38
1.0
0.7
0.45
6.35
2.38
2.0
0.75
1.4
6.35
2.38
2.0
0.75
1.4
08020R
6.35
2.38
2.0
0.8
1.4
08520R
6.35
2.38
2.0
0.85
1.4
09020R
6.35
2.38
2.0
0.9
1.4
09520R
6.35
2.38
2.0
0.95
1.4
09520L
6.35
2.38
2.0
0.95
1.4
10020R
6.35
2.38
2.0
1.0
1.4
11030R
6.35
2.38
3.0
1.1
2.6
12030R
6.35
2.38
3.0
1.2
2.6
12030L
6.35
2.38
3.0
1.2
2.6
13030R
6.35
2.38
3.0
1.3
2.6
14030R
15030R
6.35
2.38
3.0
1.4
2.6
6.35
2.38
3.0
1.5
2.6
Hand
CSVTG02505R
03005R
Dimensions (mm)
Coated
VP15KZ
D1
S1
Re
L3
6.35
2.38
6.35
2.38
03505R
6.35
2.38
04005R
6.35
2.38
04510R
6.35
2.38
05010R
6.35
05510R
6.35
06010R
06510R
07010R
07520R
07520L
CSVTT
Geometry
Without Breaker
W3 +0.03
+0
W3
Order Number
7
Re
S1
D1
L3
(Threading)
Dimensions (mm)
D1
S1
Re
0.2 0.5
6.35
2.38
0.03
0.2 0.5
6.35
2.38
0.03
CSVTT60050RR
60050RL
Geometry
Without Breaker
General Purpose (60)
RR
60
3.0
Re
RL
60
1.0
VP15KZ
Hand
0.35 0.05
Coated
Pitch
(mm)
Order Number
0.35 0.05
1.0
SMALL TOOLS
CSVTG
3.0 Re
D046
GANG TYPE
)
BORING TOOLS (FOR
TOOL POSTS
METRIC STANDARD
SBAH
Order Number
Stock
SBAHR1022
1222
SBAT
Min.
Max.
Depth Cutting
of Cut Diameter
ap (mm) (mm) Insert Screw Wrench
Dimensions (mm)
Insert Number
H1
L1
H2
3080ppL/L-B
10
21.5
120
10
NS402W NKY15R
3080ppL/L-B
12
21.5
120
12
NS403W NKY15R
SMALL TOOLS
Without off set
SBAH
With off set
Order Number
Stock
SBAHR1010
SBAT
Dimensions (mm)
Insert Number
3080ppL/L-B
H1
L1
H2
S1
10
10
120
10
10
Min.
Max.
Depth Cutting
of Cut Diameter
ap (mm) (mm) Insert Screw Wrench
NS402W NKY15R
Clamp Torque (lbf-in) : NS402W=0.7
With Breaker
Without Breaker
Breaker
INSERTS
Order Number
L3
Min. Cutting
Diameter
(mm)
8.0
95
0.05
8.0
95
8.0
95
0.05
8.0
Dimensions (mm)
Coated
VP15KZ
B 9
SBAT308000L
95
3080V5L
SBAT308000L-B
3080V5L-B
Re
Geometry
SPARE PARTS
M001
TECHNICAL DATA
N001
D047
GUIDE TO BORING BARS

aSection
organization
zOrganized by product series.


TYPE OF BORING BAR
uses illustrations and arrows to depict possible

machining applications along with cutting edge
lead angles.
indicates the initial letters for the order number,

as well as applicable insert types.
GEOMETRY
TITLE OF PRODUCT SERIES
CHIP BREAKER BY
CUTTING APPLICATION
PRODUCT FEATURES
PRODUCT SECTION
BORING BARS
DIMPLE BAR
M-FSCLC/P
Heavy metal shank

coolant thru
a Excellent vibration resistance due to light dimple head.

a Chip disposal is improved by having two channels for
chip evacuation.
is 3 to 6 times the diameter.
a l/d
Finish
CCooinserts, CPooinserts
FV
95
M-FSTUP
Light
SV
(2,2.5,3)
(2,2.5,3)
Medium
CBN
Stock
BORING BARS
R L
M-FSCLCR/L-052-C
a a
M-FSCLPR/L-062.5-C
a a
-082.5-C
a a
-103-C
a a
-123-C
a a
CCMH
CCGH
NP-CCMB
NP-CCMH
CPMH
NP-CPMB
NP-CPMH
D4
L1
L2
F1
(2,2.5,3)
21.5pp
.313
5.000
.703
.196
.281 12
.390
.016
TS253
TKY08F
2.51.5p
.375
6.000
.844
.227
.336
.450
.016
TS3D
TKY10F
2.51.5p
.500
8.000 1.125
.290
.461
.580
.016
TS3D
TKY10F
32p
.625 10.000 1.406
.352
.586
3.5
.700
.016
TS4D
TKY15F
32p
.750 10.000 1.688
.414
.711
.825
.016
TS4D
TKY15F
(Note) When using inserts with right and left hand chip breakers, please use left hand inserts for right hand holders and
right hand inserts for left hand holders.
Clamp Torque (lbf-in) : TS253=8.9, TS3D=22, TS4D=31
Light
SV
Medium
MV
(1.5,1.8,2)
(1.5,1.8,2)
PCD
CBN
(1.5,1.8,2)
H1
Finish
FV
(1.5,1.8,2)
R/L F
(2,2.5,3)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Re Clamp Screw Wrench
Dimensions (inch)
Insert Number
TPooinserts
93
MV
Order Number
Heavy metal shank

coolant thru
Order Number
Stock
D4
L1
L2
F1
(1.5,1.8,2)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
D1
Dimensions (inch)
Insert Number
R L
H1
RR
.281
M-FSTUPR/L-051.5-C
a a
1.51.5pp
.313
5.000
.703
10
.390
.016
TS2D
-061.8-C
a a
6.000
.844
.227
.336
.450
.016
TS25D TKY08F
a a
.500
8.000 1.125
.290
.461
.580
.016
TS25D TKY08F
-102-C
a a
TPMH 1.81.5pp
TPGH
1.81.5pp
NP-TPGB
NP-TPGX 22p
.375
-081.8-C
.625 10.000 1.406
.352
.586
.700
.016
TS31D TKY10F
-122-C
a a
.750 10.000 1.688
.414
.711
.825
.016
TS31D TKY10F
22p
.196
TKY06F
BORING BARS
SCREW
CLAMP
Clamp Torque (lbf-in) : TS2D=5.3, TS25D=8.9, TS31D=22
S-FSCLP
Steel shank
coolant thru
Finish
CPooinserts
FV
95
S-FSTUP
Light
SV
(2.5,3)
(2.5,3)
Medium
CBN
Steel shank
coolant thru
TPooinserts
93
Finish
FV
Light
SV
Medium
MV
(1.8,2)
(1.8,2)
PCD
CBN
(1.8,2)
R/L F
MV
Stock
Order Number
Insert Number
R L
S-FSCLPR/L-062.5-C
a a
-082.5-C
a a
-103-C
a a
-123-C
a a
-163-C
a a
D4
CPMH
NP-CPMB
NP-CPMH
L1
L2
.844
(2.5,3)
(2.5,3)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Dimensions (inch)
F1
H1
Order Number
Stock
R L
L1
L2
F1
H1
S-FSTUPR/L-061.8-C
a a
1.81.5pp
.375
6.000
.844
.227
.336
TPMH 1.81.5pp
TPGH
22p
NP-TPGB
NP-TPGX 22p
.500
2.51.5p
.375
6.000
.450
.016
TS3D
TKY10F
-081.8-C
a a
2.51.5p
.500
8.000 1.125
.290
.461
.580
.016
TS3D
TKY10F
-102-C
a a
32p
.625 10.000 1.406
.352
.586
3.5
.700
.016
TS4D
TKY15F
-122-C
a a
32p
.750 10.000 1.688
.414
.711
.825
.016
TS4D
TKY15F
-162-C
a a
32p
1.000 12.000 2.250
.598
.937
1.200
.016
TS4D
TKY15F
.227
.336
Clamp Torque (lbf-in) : TS3D=22, TS4D=31
D4
22p
(1.8,2)
(1.8,2)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Dimensions (inch)
Insert Number
8
7
.450
.580
.016
TS25D TKY08F
8.000 1.125
.290
.461
.016
TS25D TKY08F
.625 10.000 1.406
.352
.586
.700
.016
TS31D TKY10F
.750 10.000 1.688
.414
.711
.825
.016
TS31D TKY10F
1.000 12.000 2.250
.638
.937
1.280
.016
TS31D TKY10F
Clamp Torque (lbf-in) : TS25D=8.9, TS31D=22
E006
CCpp type inserts
A101A106
CUTTING CONDITIONS
E011
CPpp type inserts
A107, A108
TPpp type inserts
A122A124
SPARE PARTS
M001
CBN & PCD inserts
B038B041, B058
CBN & PCD inserts
B045, B046
TECHNICAL DATA
N001
LEGEND FOR STOCK

STATUS MARK
REFERENCE PAGE

indicates reference pages for details

of inserts that are applicable to the
title product.
PRODUCT STANDARDS
minimum cutting diameters,
standard corner radius,
and spare parts.
MIN. CUTTING DIAMETER

is color-coded to locate at a glance.
aTo
E000
Order:
PAGE REFERENCE
SPARE PARTS
TECHNICAL DATA
CUTTING CONDITIONS
indicates reference pages, on the
right hand page of each double-page
spread.
E007
TURNING
BORING BARS
CLASSIFICATION ....................................................................................... E002
IDENTIFICATION ......................................................................................... E004
STANDARD BORING BARS
SCREW CLAMP DIMPLE BAR ............................................................... E006
SCREW CLAMP TYPE BORING BARS .................................................. E012
DOUBLE CLAMP DIMPLE BAR.............................................................. E021
MULTIPLE CLAMP TYPE BORING BARS ............................................. E024
AL TYPE BORING BARS ........................................................................ E028
MICRO-DEX BORING BARS ................................................................... E029
MICRO-MINI BORING BARS .................................................................. E031
MICRO-MINI TWIN BORING BARS ........................................................ E032
RBH TYPE HOLDER (FOR MICRO-MINI AND MICRO-MINI TWIN) ...... E034
SBH TYPE HOLDER (FOR MICRO-MINI AND MICRO-MINI TWIN) ...... E037
by Alphabetical order
*Arranged
E034
CB
E032
E033
E031
E013
E014
E016
E017
E019
E018
E018
E006
E008
E008
E007
E010
E010
E009
E009
E027
E012
E020
E020
CR
CoooR-BLS
C-SCLC
C-SDQC
C-STUC
C-SWL
C-SWLO
FSWL1
FSWL2
M-FSCLC/P
M-FSDQC
M-FSDUC
M-FSTUP
M-FSVJB/C
M-FSVPB/C
M-FSVUB/C
M-FSWUB/P
M-MWLN
M-SCLC
M-SWLO
M-SWLO
E036
E037
E029
E021
E021
E022
E022
E023
E023
E006
E007
E024
E024
E025
E025
E026
E026
E012
E013
E014
E015
RBH (INCH)
RBH (MM)
SBH
SCLC
S-DCLN
S-DDUN
S-DSKN
S-DTFN
S-DVUN
S-DWLN
S-FSCLP
S-FSTUP
S-MCLN
S-MDUN
S-MSKN
S-MTFN
S-MVUN
S-MWLN
S-SCLC
S-SDQC
S-SDUC
S-SSKC
E028
E015
E016
E017
E019
E030
E029
S-STFE
S-STUC
S-SVQC
S-SVUC
S-SWUC
STUC
SWUB
E001
BORING BARS
CLASSIFICATION
' = 75
Type of Tool
'
DIMPLE BAR
a
a
'
M-FSTUP, S-FSTUP M-FSDUC M-FSVUB/C M-FSWUB/P
^ E015
DIMPLE BAR
a
a
a
a
^ E009
^ E009
S-SDUC
S-STUC, C-STUC
S-SVUC
S-SWUC
^ E014
^ E015, E016
S-DSKN
S-DTFN
S-DDUN
S-DVUN
Negative rake.
Two wall pocket.
Pin lock and top clamp
retention.
a (Opt.) Single clamp available
as clamp on or pin lock holder.
S-MSKN
S-MTFN
S-MDUN
S-MVUN
SWUB
STUC
^ E022
^ E021
^ E023
a
a
a
^ E025
AL Type Boring Bars
^ E008
Negative rake.
New double clamp type.
Holds inserts securely.
Excellent cutting edge
repeatability.
^ E022
M Type Boring Bars
^ E007
Two wall pocket.

7 positive insert, low cutting
force.
a Screw-on type.
a
a
S-SSKC
DOUBLE CLAMP
' = 93
'

is & .390inch.
5, 11 positive insert.
Excellent vibration resistance
due to light dimple head.
a Chip disposal is improved by having
two channels for chip evacuation.
a l/d is 3 to 6 times the diameter.
SCREW CLAMP
S Type Boring Bars

BORING BARS
Features
' = 90, 91
^ E025
^ E024
^ E026
Shank sizes &.625inch thru

& 1.000inch.
a Screw-on type.
a Recommended for aluminum,
nonferrous metals and plastics.
a
S-STFE
^ E028
MICRO-DEX
Boring Bars
(Carbide Shank)

is & 5mm (.197inch).
a 7positive insert.
a
MICRO-MINI TWIN
Boring Bars
MICRO-MINI
Boring Bars
RBH Type
Holder
^ E029
^ E030

is & 2.2mm (.087inch).
a Solid carbide type with two
cutting edges.
a Continuous cutting from
boring to facing.
a With or without a chip breaker.
a
a
a
The minimum cutting diameter is

& 3.2mm (.126inch).
Solid carbide type (Single cutting edges).
Cutting edge can be shaped
according to the application. Thus,
it covers a wide cutting range
(threading,grooving,copying, etc.).
CooF/HR-BLS
^ E031
Holder for MICRO-MINI TWIN

and MICRO-MINI.
a Round shanks suitable for use
with frontal gang type tool
posts with sleeve.
a
RBH
Inch ^ E034, Metric ^ E036
SBH Type
Holder
a
a
Holder for MICRO-MINI TWIN

and MICRO-MINI.
Square shanks suitable for use
with frontal gang type tool
posts.
SBH
^ E037
(Note 1) S : Steel shank, M : Heavy metal shank, C : Carbide shank. (For Micro-dex boring bars, carbide shank only.)
E002
^ E017
^ E019
' = 10730 11730 ' = 142
u e e
u*
Small Diameter
Cutting
Specialized
Coolant Thru
Vibration
Resisiance
Operation
Efciency
Clamp Rigidity
e
M-FSDQC M-FSVPB/C M-FSVJB/C
^ E006
^ E008
C-SWLO, M-SWLO S-SCLC, M-SCLC, C-SCLC
^ E019, E020 ^ E012, E013
C-SWL
^ E017
S-DCLN
S-DWLN
S-MCLN
S-MWLN, M-MWLN
^ E021
FSWL1, 2 S-SDQC, C-SDQC

^ E018
^ E013, E014
^ E010
^ E010
S-SVQC
^ E016
e e
^ E023
e
^ E024
BORING BARS
M-FSCLC/P, S-FSCLP
'
Low Cutting Resistance (Sharpness)
'
'
Selection Standard
Economical
' = 95
^ E026, E027
SCLC
^ E029
e
CBooRS(-B)
^ E032
CRooRS-01(B)
^ E033
(Note 2) e: 1st recommendation. u: 2nd recommendation.

(Note 3)
Indicates in case that shank material is carbide.
E003
BORING BARS
IDENTIFICATION
y S Type, D Type, Double Clamp Boring Bars, M Type Boring Bars
1 action
C
Carbide Shank
Heavy Metal Shank
Steel Shank
BORING BARS
2 action
z Shank Material
b Insert Relief Angle
20
c Insert Shape
x Method of Holding
m Shank Size
n Hand of Tool
v Tool Style
06
08
10
12
16
20
24
28
32
.375
.500
.625
.750
1.000
1.250
1.500
1.750
2.000
, Insert Size
Inscribed Circle
of Insert (inch)
.187
.219
.250
.313
.375
.500
.625
.750 1.000
1.5
1.8
2.5
2.5
2.5
11
E004
M
S
Heavy Metal Shank

Steel Shank
z Shank Material
n Insert Relief Angle
One piece
type
x Structure
Screw Clamp
c Clamp Type
m Hand of Tool
, Shank Diameter
RHOMBIC 80
93
RHOMBIC 55
95
TRIANGULAR 60
10730
RHOMBIC 35
11730
TRIGON
142
BORING BARS
y SCREW CLAMP DIMPLE BAR
b Cutting Angle
v Insert Shape
. Insert Size
Right Hand
05
.313
Inscribed circle of insert
.187
.219
.250
.313
.375
11
Left Hand
06
.375
RHOMBIC 80
2.5
08
.500
RHOMBIC 55
10
.625
TRIANGULAR 60
1.5
1.8
12
.750
RHOMBIC 35
1.5
16
1.000
TRIGON
1.5
E005
BORING BARS
SCREW
CLAMP
DIMPLE BAR
M-FSCLC/P
Heavy metal shank

coolant thru

chip evacuation.
a l/d
Finish
CCooinserts, CPooinserts
FV
95
Light
SV
(2,2.5,3)
(2,2.5,3)
Medium
CBN
MV
Order Number
Stock
BORING BARS
R L
M-FSCLCR/L-052-C
a a
M-FSCLPR/L-062.5-C
a a
-082.5-C
a a
-103-C
a a
-123-C
a a
CCMH
CCGH
NP-CCMB
NP-CCMH
CPMH
NP-CPMB
NP-CPMH
(2,2.5,3)
Dimensions (inch)
Insert Number
(2,2.5,3)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
D4
L1
L2
F1
21.5pp
.313
5.000
.703
.196
.281 12
.390
.016
TS253
TKY08F
2.51.5p
.375
6.000
.844
.227
.336
.450
.016
TS3D
TKY10F
2.51.5p
.500
8.000 1.125
.290
.461
.580
.016
TS3D
TKY10F
32p
.625 10.000 1.406
.352
.586
3.5
.700
.016
TS4D
TKY15F
32p
.750 10.000 1.688
.414
.711
.825
.016
TS4D
TKY15F
H1
Clamp Torque (lbf-in) : TS253=8.9, TS3D=22, TS4D=31
S-FSCLP
Steel shank
coolant thru
Finish
CPooinserts
FV
95
Light
SV
(2.5,3)
(2.5,3)
Medium
CBN
MV
Order Number
Stock
R L
S-FSCLPR/L-062.5-C
a a
-082.5-C
a a
-103-C
a a
-123-C
a a
-163-C
a a
L1
L2
F1
H1
2.51.5p
.375
6.000
.844
.227
.336
.450
.016
TS3D
TKY10F
2.51.5p
.500
8.000 1.125
.290
.461
.580
.016
TS3D
TKY10F
32p
.625 10.000 1.406
.352
.586
3.5
.700
.016
TS4D
TKY15F
32p
.750 10.000 1.688
.414
.711
.825
.016
TS4D
TKY15F
32p
1.000 12.000 2.250
.598
.937
1.200
.016
TS4D
TKY15F
D4
CPMH
NP-CPMB
NP-CPMH
(2.5,3)
Dimensions (inch)
Insert Number
(2.5,3)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Clamp Torque (lbf-in) : TS3D=22, TS4D=31
E006
CCpp type inserts
A101A106
CPpp type inserts
A107, A108
CBN & PCD inserts
B038B041, B058
M-FSTUP
Heavy metal shank

coolant thru
TPooinserts
93
Finish
Light
SV
FV
Medium
MV
(1.5,1.8,2)
(1.5,1.8,2)
PCD
CBN
(1.5,1.8,2)
R/L F
(1.5,1.8,2)
Stock
R L
Dimensions (inch)
Insert Number
D4
L1
L2
F1
H1
M-FSTUPR/L-051.5-C
a a
1.51.5pp
.313
5.000
.703
.196
.281
10
.390
.016
TS2D
-061.8-C
a a
6.000
.844
.227
.336
.450
.016
TS25D TKY08F
-081.8-C
.500
8.000 1.125
.290
.461
.580
.016
TS25D TKY08F
-102-C
a a
TPMH 1.81.5pp
TPGH
1.81.5pp
NP-TPGB
NP-TPGX 22p
.375
a a
.625 10.000 1.406
.352
.586
.700
.016
TS31D TKY10F
-122-C
a a
.750 10.000 1.688
.414
.711
.825
.016
TS31D TKY10F
22p
TKY06F
BORING BARS
Order Number
(1.5,1.8,2)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Clamp Torque (lbf-in) : TS2D=5.3, TS25D=8.9, TS31D=22
S-FSTUP
Steel shank
coolant thru
TPooinserts
93
Finish
FV
Light
SV
Medium
MV
(1.8,2)
(1.8,2)
PCD
CBN
(1.8,2)
R/L F
Order Number
Stock
R L
D4
S-FSTUPR/L-061.8-C
a a
1.81.5pp
-081.8-C
a a
-102-C
a a
-122-C
a a
TPMH 1.81.5pp
TPGH
22p
NP-TPGB
NP-TPGX 22p
-162-C
a a
22p
(1.8,2)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Dimensions (inch)
Insert Number
(1.8,2)
L1
L2
F1
H1
.375
6.000
.844
.227
.336
.450
.016
TS25D TKY08F
.500
8.000 1.125
.290
.461
.580
.016
TS25D TKY08F
.625 10.000 1.406
.352
.586
.700
.016
TS31D TKY10F
.750 10.000 1.688
.414
.711
.825
.016
TS31D TKY10F
1.000 12.000 2.250
.638
.937
1.280
.016
TS31D TKY10F
Clamp Torque (lbf-in) : TS25D=8.9, TS31D=22
CUTTING CONDITIONS
E011
TPpp type inserts
A122A124
SPARE PARTS
M001
CBN & PCD inserts
B045, B046
TECHNICAL DATA
N001
E007
BORING BARS
SCREW
CLAMP
DIMPLE BAR
M-FSDUC
Heavy metal shank

coolant thru

chip evacuation.
a l/d
Finish
DCooinserts
FV
93
(2,3)
(2,3)
(2,3)
PCD
CBN
BORING BARS
R L
M-FSDUCR/L-062-C
a a
-082-C
a a
-102-C
a a
-123-C
a a
D4
DCMT
DCET
DCGT
NP-DCMW
NP-DCGW
L1
L2
F1
F2
(2,3)
(2,3)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR D1
Dimensions (inch)
Insert Number
R/L F
(2,3)
Stock
Medium
MV
Medium
Standard
Order Number
Light
SV
H1
21.5p
.375
6.000 .675 .317 .130 .336 7.5
.525
.016
TS25
TKY08F
21.5p
.500
8.000 .833 .380 .130 .461 6
.667
.016
TS25
TKY08F
21.5p
.625 10.000 .781 .442 .130 .586 5
.781
.016
TS25
TKY08F
32.5p
.750 10.000 .844 .615 .240 .711 5
1.200
.031
TS43
TKY15F
M-FSDQC
Heavy metal shank

coolant thru
Finish
DCooinserts
FV
107
30
Order Number
Stock
(2,3)
(2,3)
(2,3)
PCD
CBN
R L
M-FSDQCR/L-062-C
a a
-082-C
a a
-102-C
a a
-123-C
a a
D4
DCMT
DCET
DCGT
NP-DCMW
NP-DCGW
L1
L2
F1
F2
R/L F
(2,3)
(2,3)
(2,3)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR D1
Dimensions (inch)
Insert Number
Medium
MV
Medium
Standard
Light
SV
H1
21.5p
.375
6.000 .769 .290 .102 .336
.488
.016
TS25
TKY08F
21.5p
.500
8.000 .938 .352 .102 .461
.667
.016
TS25
TKY08F
21.5p
.625 10.000 .879 .415 .102 .586
.781
.016
TS25
TKY08F
32.5p
.750 10.000 .975 .521 .146 .711
.938
.031
TS43
TKY15F
E008
DCpp type inserts
A109A113
CBN & PCD inserts
B042, B043
M-FSWUB/P
Heavy metal shank

coolant thru
WBooinserts, WPooinserts
Finish
R/L F
(1.5,2,3)
Medium
93
MV
The &.313 and &.375 shanks are 0.
Stock
R L
M-FSWUBR/L-051.5-C
a a
-061.5-C
a a
M-FSWUPR/L-082-C
a a
-102-C
a a
-123-C
a a
WBMT
WBGT
WPMT
Dimensions (inch)
Insert Number
D4
L1
1.51.5p
.313
5.000
1.51.5p
.375
6.000
21.5p
.500
8.000 1.125
.289
21.5p
.625 10.000 1.406
.352
32p
.750 10.000 1.688
.414
.711
L2
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
F1
H1
.703
.196
.281
14
.391
.008
TS2
TKY06F
.844
.227
.336
11
.450
.008
TS2
TKY06F
.461
.583
.016
TS253
TKY08F
.586
.703
.016
TS253
TKY08F
.825
.031
TS4
TKY15F
BORING BARS
Order Number
(1.5,2,3)
Clamp Torque (lbf-in) : TS2=5.3, TS253=8.9, TS4=31
M-FSVUB/C
Heavy metal shank

coolant thru
VCooinserts, VBooinserts
Finish
R/L F
(1.5,2)
Medium
93
MV
(1.5,2)
Order Number
Stock
R L
M-FSVUCR/L-081.5-C
a a
M-FSVUBR/L-102-C
a a
-122-C
a a
D4
VCGT
VCMT
VBGT
VBMT
NP-VBGW
Dimensions (inch)
Insert Number
L1
L2
F1
F2
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR D1
H1
1.51.5p
.500
8.000 1.042 .447 .197 .461
.667
.016
TS202
TKY06F
22p
.625 10.000 1.269 .608 .295 .586
.781
.016
TS255
TKY08F
22p
.750 10.000 1.519 .670 .295 .711
.938
.016
TS255
TKY08F
Clamp Torque (lbf-in) : TS202=5.3, TS255=8.9
WBpp type inserts
A132
WPpp type inserts
A135
VCpp type inserts
A128, A129
VBpp type inserts
A125A127
CBN & PCD inserts
B047, B063
CUTTING CONDITIONS
E011
E009
BORING BARS
SCREW
CLAMP
DIMPLE BAR
M-FSVPB/C

chip evacuation.
a l/d
Heavy metal shank

coolant thru
Finish
FV
(1.5,2)
Medium
117
30
MV
(1.5,2)
Order Number
Stock
BORING BARS
R L
M-FSVPCR/L-061.5-C
a a
M-FSVPBR/L-082-C
a a
-102-C
a a
-122-C
a a
D4
VCGT
VCMT
VBGT
VBMT
NP-VBGW
Dimensions (inch)
Insert Number
L1
L2
F1
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR D1
F2
H1
1.51.5p
.375
6.000 .938 .306 .118 .336
.600
.016
TS202
TKY06F
22p
.500
8.000 1.167 .407 .157 .461
.833
.016
TS255
TKY08F
22p
.625 10.000 1.367 .490 .177 .586
.977
.016
TS255
TKY08F
22p
.750 10.000 1.500 .572 .197 .711
1.125
.016
TS255
TKY08F
M-FSVJB/C
Heavy metal shank

coolant thru
Finish
FV
142
Medium
MV
(1.5,2)
(1.5,2)
Medium
Standard
Order Number
Stock
R L
M-FSVJCR/L-081.5-C
a a
-101.5-C
a a
M-FSVJBR/L-122-C
a a
D4
VCGT
VCMT
VBET
VBGT
VBMT
Dimensions (inch)
Insert Number
L1
L3
F1
(2)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
H1
1.51.5p
.500
8.000 1.083
.093
.461
.667
.016
TS202
TKY06F
1.51.5p
.625 10.000 1.406
.076
.586
.781
.016
TS202
TKY06F
22p
.750 10.000 1.406
.060
.711
.938
.016
TS255
TKY08F
E010
VCpp type inserts
A128, A129
VBpp type inserts
A125A127
l/d < 3
3 < l/d < 5
l/d < 3
3 < l/d < 6
Cutting
Mode
Breaker
Finishing
FV
Light
SV
Medium
MV
Work Material
P
Steel Shank
Heavy Metal Shank
Mild Steel
<180HB
Finishing
Carbon Steel
Alloy Steel
180 280HB
Light
Cast Iron
Tensile Strength<350MPa
MV
Finishing
FV
Light
SV
Medium
MV
Finishing
Medium
H Heat Treated Steel 3565HRC
NX2525
Cutting Speed
(SFM)
Feed
(IPR)
D.O.C.
(inch)
Feed
(IPR)
D.O.C.
(inch)
555 (390 720)
.004 (.002 .006)
.020
.004 (.002 .006)
.020
VP45N
460 (295 620)
.008 (.004 .010)
.040
.006 (.002 .008)
.040
VP15TF
590 (425 755)
.008 (.004 .010)
.040
.006 (.002 .008)
.040
VP45N
425 (260 590)
.010 (.006 .014)
.080
.008 (.006 .010)
.060
VP15TF
525 (360 690)
.010 (.006 .014)
.080
.008 (.006 .010)
.060
VP15TF
460 (295 620)
.004 (.002 .006)
.020
.004 (.002 .006)
.020
NX2525
425 (260 590)
.004 (.002 .006)
.020
.004 (.002 .006)
.020
VP15TF
425 (260 590)
.008 (.004 .010)
.040
.006 (.002 .008)
.040
UE6020
460 (295 620)
.008 (.004 .010)
.040
.006 (.002 .008)
.040
VP15TF
390 (230 555)
.010 (.006 .014)
.080
.008 (.006 .010)
.060
UE6020
425 (260 590)
.010 (.006 .014)
.080
.008 (.006 .010)
.060
VP15TF
490 (360 620)
.004 (.002 .006)
.020
.004 (.002 .006)
.020
US7020
490 (360 620)
.008 (.004 .010)
.040
.006 (.002 .008)
.040
VP15TF
425 (295 555)
.008 (.004 .010)
.040
.006 (.002 .008)
.040
.040
US7020
460 (330 590)
.008 (.006 .010)
.080
.008 (.006 .010)
VP15TF
390 (260 525)
.008 (.006 .010)
.080
.008 (.006 .010)
.040
F/FS
HTi10
425 (295 525)
.006 (.004 .008)
.020
.006 (.004 .008)
.020
MV
VP15TF
295 (195 390)
.008 (.006 .010)
.080
.008 (.006 .010)
.060
F/FS
HTi10
985 (655 1310)
.004 (.002 .006)
.020
.004 (.002 .006)
.020
No Breaker
MD220
655 (490 820)
.004 (.002 .006)
.080
.004 (.002 .006)
.040
Finishing No Breaker
MB825
330 (260 655)
.004 (.002 .006)
.006
.004 (.002 .006)
.004
N
Aluminium Alloy
SV
Medium
Stainless Steel
180 280HB
FV
RecomGrade
mendation
Finishing
BORING BARS
* If the DIMPLE BAR vibrates, reduce cutting speed to 70% of the above.
y CCG/MT, CPGT, CPMX, TPGD/P, TPGA/M, TPMX inserts
By changing the insert screw, it is possible to use the inserts listed on the left hand side.
Order Number
Insert Screw
CCG/MT21.5o
Can be used as it is.
CPGT2.51.5o
Change to TS3.
CPGT32o
Change to TS4.
CPMX2.51.5o
CPMX32o
TPGD/P1.51.5o
Change to CS200T.
TPGD/P1.81.5o
Change to CS250T.
TPGA/M22o
Change to CS300890T.
TPMX1.51.5o
Change to CS200T.
TPMX1.81.5o
Change to CS250T.
TPMX22o
Change to CS300890T.
Remark
If the screw is too long then please

grind away the unnecessary material.
E011
BORING BARS
SCREW CLAMP TYPE
S-SCLC
a Two wall pocket.

a 7 positive insert, low cutting force.
a Screw-on type.
a Steel and carbide shanks are stocked
in various diameters.
Finish
CCooinserts
Steel shank
FV
(2,3)
(2,3,4)
Flat Top
PCD/CBN
(2,3,4)
(2,3,4)
Order Number
Stock
D4
L1
L3
F1
H1
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
-082
a a
-103
a a
-123
a a
-164
a a
-204
a a
BORING BARS
a a
CCMT
CCMW
CCGW
CCGT
CCET
CCMH
NP-CCGW
21.5p
.375
6.000
.625
.250
.340
15
.477
.016
TS25
TKY08F
21.5p
.500
6.000
.750
.313
.460
13
.602
.016
TS25
TKY08F
32.5p
.625
8.000 1.250
.406
.560
10
.797
.031
TS4
TKY15F
32.5p
.750 10.000 1.875
.500
.700
.954
.031
TS4
TKY15F
43p
1.000 12.000 2.500
.641
.910
1.219
.031
TS5
TKY25F
43p
1.250 12.000 2.500
.875 1.160
1.579
.031
TS5
TKY25F
Dimensions (inch)
Insert Number
R L
S-SCLCR/L-062
Medium
Standard
M-SCLC
CCooinserts
Heavy metal shank
Finish
LF
95
(03,04)
PCD/CBN
(03,04)
Order Number
Stock
R
M-SCLCR-063
-073
-064
03S1ppL-F
CCGT
03S1ppL-F
NP-CCMW
04T0ppL-F
Dimensions (inch)
Insert Number
Min.
Cutting
Diameter
(inch)
D1 Clamp Screw Wrench
D4
L1
F1
H1
RR
.188
3.000
.100
.173
15
.200
TS16
TKY06F
.219
3.500
.120
.199
14
.240
TS16
TKY06F
.250
4.000
.140
.230
14
.280
TS21
TKY06F
E012
CCpp type inserts
A101A106
CBN & PCD inserts
B038B040, B058
Finish
CCooinserts
Carbide shank
FV
95
(2,3)
(2,3)
Flat Top
PCD/CBN
(2,3)
(2,3)
Stock
Order Number
C-SCLCR/L-062
-082
-103
D4
L1
L3
F1
H1
21.5p
.375
6.000
.625
.250
.340
21.5p
.500
6.000
.750
.313
32.5p
.625
8.000
1.250
.406
R L
CCMT
a a CCMW
CCGW
a a CCGT
CCET
a a NP-CCGW
CCMH
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Dimensions (inch)
Insert Number
Medium
Standard
15
.477
.016
TS25
TKY08F
.460
13
.602
.016
TS25
TKY08F
.560
10
.797
.031
TS4
TKY15F
S-SDQC
DCooinserts
Steel shank
Finish
Finish
R/L F
FV
Stock
Order Number
(2,3)
(2,3)
(2,3)
(2,3)
Medium
Flat Top
PCD/CBN
(2,3,4)
(2,3)
MJ
R L
S-SDQCR/L-082
a a
-102
a a
-123
a a
-164
a a
DCMT
DCMW
DCGW
DCGT
DCET
NP-DCMW
NP-DCMT
(2,3)
(2,3,4)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Dimensions (inch)
Insert Number
Medium
MV
Medium
Standard
Light
SV
D4
L1
21.5p
.500
6.000
.875 .375
.460
10
.665
.016
TS25
TKY08F
21.5p
.625
8.000 1.000 .406
.560
.797
.016
TS25
TKY08F
32.5p
.750 10.000 1.250 .500
.700
.954
.031
TS4
TKY15F
1.000 12.000 1.500 .641
.910
1.219
.031
TS5
TKY25F
43p
L3
F1
BORING BARS
C-SCLC
H1

Steel Shank
Heavy Metal Shank
Carbide Shank
Work Material
Hardness Cutting Mode
Carbon Steel
Alloy Steel
180 280HB
Stainless Steel
<200HB
Aluminum Alloy
Light Cutting
Medium Cutting
Light Cutting
Medium Cutting
Light Cutting
Medium Cutting
Cutting Speed
(SFM)
l/d < 3
l/d < 3
l/d < 5
Feed
(IPR)
295 525
195 395
330 590
165 295
.002 .006
.006 .014
.002 .006
.006 .010
655 1310
490 820
.002 .006
.002 .006
Depth of Cut
(inch)
3 < l/d < 4 (Shank Diameter > 1.000inch)

3 < l/d < 6
5 < l/d < 7
Cutting Speed
Feed
Depth of Cut
(inch)
(SFM)
(IPR)
.002 .006
.004 .008
.002 .006
.004 .008
.008
.059
.008
.079
260 490
165 360
330 590
130 260
.008
.079
655 1310
490 820
.002 .006
.002 .006
.008
.059
.008
.118
.008
.039
CCpp type inserts
A101A106
DCpp type inserts
A109A113
SPARE PARTS
M001
CBN & PCD inserts
B038B040, B042, B043, B058, B059
TECHNICAL DATA
N001
E013
BORING BARS
SCREW CLAMP TYPE
C-SDQC
a Two wall pocket.

a Screw-on type.
Carbide shank
DCooinserts
107
30
Finish
Stock
R L
C-SDQCR/L-082
-102
-123
DCMT
a a DCMW
DCGW
a a DCGT
DCET
NP-DCMW
a a
NP-DCMT
Medium
MV
(2,3)
(2,3)
(2,3)
(2,3)
Medium
Flat Top
PCD/CBN
(2,3)
(2,3)
MJ
(2,3)
(2,3)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Dimensions (inch)
Insert Number
SV
Medium
Standard
Order Number
Light
R/L F
FV
BORING BARS
Finish
D4
L1
L3
F1
H1
21.5p
.500
6.000
.875
.375
.460
10
.665
.016
TS25
TKY08F
21.5p
.625
8.000 1.000
.406
.560
.797
.016
TS25
TKY08F
32.5p
.750 10.000 1.250
.500
.700
.954
.031
TS4
TKY15F
S-SDUC
Steel shank
DCooinserts
93
Finish
Finish
(2,3)
(2,3)
(2,3)
Medium
Flat Top
PCD/CBN
(2,3,4)
(2,3)
R L
S-SDUCR/L-062
a a
-082
a a
-102
a a
-123
a a
-164
a a
DCMT
DCMW
DCGW
DCGT
DCET
NP-DCMW
NP-DCMT
MJ
(2,3,4)
(2,3)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Dimensions (inch)
Insert Number
D4
L1
L3
F1
H1
21.5p
.375
6.000
.625
.437
.340
21.5p
.500
6.000
.750
.500
.460
21.5p
.625
8.000 1.250
.563
.560
32.5p
.750 10.000 1.875
.625
1.000 12.000 2.500
.750
43p
Medium
MV
(2,3)
Stock
SV
Medium
Standard
Order Number
Light
R/L F
FV
.664
.016
TS25
TKY08F
.789
.016
TS25
TKY08F
.954
.016
TS25
TKY08F
.700
1.079
.031
TS4
TKY15F
.910
1.329
.031
TS5
TKY25F
E014
DCpp type inserts
A109A113
CBN & PCD inserts
B042, B043, B059
S-SSKC
Finish
SCooinserts
Steel shank
FV
Medium
Standard
(3,4)
(3)
Flat Top
75
(3,4)
R L
S-SSKCR/L-103
a a
-123
a a
-164
a a
D4
.625
32.5p
SCMT
SCMW
32.5p
43p
Dimensions (inch)
Insert Number
L1
L3
F1
H1
8.000 1.250 .406
.560
10
.797
.031
TS4
TKY15F
.750 10.000 1.875 .500
.700
.954
.031
TS4
TKY15F
1.000 12.000 2.500 .641
.910
1.219
.031
TS5
TKY25F
* Clamp Torque (lbf-in) : TS4=31, TS5=66
S-STUC
TCooinserts
Steel shank
93
Finish
FV
Finish
BORING BARS
Stock
Order Number
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
FJ
(2,3)
(2,3)
Medium
Flat Top
Standard
Stock
Order Number
H1
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
.340
15
.477
.016
TS25
TKY08F
Dimensions (inch)
Insert Number
R L
D4
L1
L3
F1
(2,3)
(2,3)
S-STUCR/L-062
a a
21.5p
.375
6.000
.625 .250
-082
a a
21.5p
.500
6.000
.750 .313
.460
13
.602
.016
TS25
TKY08F
-102
a a
21.5p
.625
8.000 1.250 .406
.560
10
.797
.016
TS25
TKY08F
-123
a a
32.5p
.750 10.000 1.875 .500
.700
.954
.031
TS4
TKY15F
-163
a a
32.5p
1.000 12.000 2.500 .641
.910
1.219
.031
TS4
TKY15F
-203
a a
32.5p
1.250 12.000 2.500 .875 1.160
1.579
.031
TS4
TKY15F
TCMT
TCMW
TCGT
NP-TCGW

Steel Shank
Heavy Metal Shank
Carbide Shank
Work Material
Carbon Steel
Alloy Steel
180 280HB
Stainless Steel
< 200HB
Aluminum Alloy
Light Cutting
Medium Cutting
Light Cutting
Medium Cutting
Light Cutting
Medium Cutting
Cutting Speed
(SFM)
l/d < 3
l/d < 3
l/d < 5
Feed
(IPR)
295 525
195 395
330 590
165 295
.002 .006
.006 .014
.002 .006
.006 .010
655 1310
490 820
.002 .006
.002 .006
Depth of Cut
(inch)

3 < l/d < 6
5 < l/d < 7
Cutting Speed
Feed
Depth of Cut
(SFM)
(IPR)
(inch)
.008
.079
260 490
165 360
330 590
130 260
.002 .006
.004 .008
.002 .006
.004 .008
.008
.039
.008
.079
655 1310
490 820
.002 .006
.002 .006
.008
.059
.008
.118
.008
.059
SCpp type inserts
A117
TCpp type inserts
A119, A120
SPARE PARTS
M001
CBN & PCD inserts
B044, B060
TECHNICAL DATA
N001
E015
BORING BARS
SCREW CLAMP TYPE
C-STUC
a Two wall pocket.

a Screw-on type.
Finish
TCooinserts
Carbide shank
FV
93
(2)
(2)
Medium
Flat Top
Standard
Order Number
Stock
R L
C-STUCR/L-062
a a
-082
a a
-102
a a
TCMT
TCMW
TCGT
NP-TCGW
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Dimensions (inch)
Insert Number
L3
F1
(2)
(2)
BORING BARS
Finish
FJ
D4
L1
H1
21.5p
.375
6.000
.625 .250
.340
15
.477
.016
TS25
TKY08F
21.5p
.500
6.000
.750 .313
.460
13
.602
.016
TS25
TKY08F
21.5p
.625
8.000
1.250 .406
.560
10
.797
.016
TS25
TKY08F
S-SVQC
VCooinserts
Steel shank
Medium
Finish
FV
Standard
(3)
117
30
(2,3)
Order Number
Stock
S-SVQCR/L-102
a a
-122
a a
-163
a a
D4
VCMT
VCMW
NP-VCGW
L1
L3
F1
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Dimensions (inch)
Insert Number
R L
(2,3)
Flat Top
H1
22p
.625
8.000 1.000 .406
.560
.797
.016
TS25
TKY08F
22p
.750 10.000 1.250 .500
.700
.954
.016
TS25
TKY08F
33p
1.000 12.000 1.500 .641
.910
1.219
.031
TS4
TKY15F
E016
TCpp type inserts
A119, A120
VCpp type inserts
A128, A129
CBN & PCD inserts
B044, B048, B060, B063
S-SVUC
VCooinserts
Steel shank
Finish
Medium
Standard
FV
(2)
93
(2,3)
R L
S-SVUCR/L-122
a a
-163
a a
Dimensions (inch)
Insert Number
D4
VCMT
VCMW
NP-VCGW
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
L1
L3
F1
H1
22p
.750 10.000 1.250 .500
.700
1.000
.016
TS25
TKY08F
33p
1.000 12.000 1.500 .641
.910
1.281
.031
TS4
TKY15F
C-SWL
WCooinserts
Carbide shank
Finish
FJ
95
Light
Finish
R/L
BORING BARS
Stock
Order Number
(2,3)
Flat Top
Standard
(2)
(1.2,1.5)
Medium
CBN
(1.2,1.5,2)
MJ
Right hand tool

holder shown.
Stock
Order Number
R L
C-SWL0502R/LS
a a
05S3R/LM
a a
0504R/L
a a
WCMT
WCGT
NP-WCMW
NP-WCGW
Dimensions (inch)
Insert Number
(1.5,2)
(2)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
D4
L1
1.21p
.313
5.000
1.000 .114
.282
17
.228
.016
TS21
TKY06F
1.51.5p
.313
5.000
1.370 .156
.282
15
.312
.016
TS2
TKY06F
21.5p
.313
5.000
.598 .203
.282
15
.406
.016
TS25
TKY08F
L3
F1
H1
Clamp Torque (lbf-in) : TS21=5.3, TS2=5.3, TS25=8.9

l/d < 3
Heavy Metal Shank
l/d < 3
3 < l/d < 6
Carbide Shank
l/d < 5
5 < l/d < 7
Steel Shank
Work Material
P
M
N
Carbon Steel
Alloy Steel
180 280HB
Stainless Steel
< 200HB
Aluminum Alloy
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
Light Cutting
295 525
.002 .006
.008
260 490
.002 .006
.008
Medium Cutting
195 395
.006 .014
.118
165 360
.004 .008
.059
Light Cutting
330 590
.002 .006
.008
330 590
.002 .006
.008
Medium Cutting
165 295
.006 .010
.079
130 260
.004 .008
.039
Light Cutting
655 1310
.002 .006
.008
655 1310
.002 .006
.008
Medium Cutting
490 820
.002 .006
.079
490 820
.002 .006
.059
VCpp type inserts
A128, A129
WCpp type inserts
A133, A134
SPARE PARTS
M001
CBN & PCD inserts
B048, B049, B063, B064
TECHNICAL DATA
N001
E017
BORING BARS
SCREW CLAMP TYPE
FSWL1
a Two wall pocket.

a Screw-on type.
WCooinserts
Steel shank
Finish
FJ
Light
Finish
R/L
95
Standard
(2,3)
(1.2)
Medium
CBN
(1.2,2,3)
MJ
Order Number
Stock
R
BORING BARS
FSWL108RS
108R
110R
112R
WCMT
WCGT
WCMT
NP-WCGW
NP-WCMW
Dimensions (mm)
Insert Number
(2,3)
(2,3)
Min. Standard
Cutting Corner
Diameter Radius
(mm)
(inch)
RR
D1
D4
L1
L3
F1
H1
1.21p
100
19
2.9
17
21.5p
125
10
15
21.5p
10
150
12
32.5p
12
180
15
11
5.8
.016
TS21
TKY06F
10
.016
TS25
TKY08F
13
12
.016
TS25
TKY08F
13
16
.031
TS4
TKY15F
FSWL2
WCooinserts
Carbide shank
Finish
FJ
Light
Finish
R/L
95
Standard
(2,3)
(1.2,1.5)
Medium
CBN
(1.2,2,3)
MJ
Order Number
Stock
R
FSWL208RS
208RM
208R
212R
WCMT
WCGT
NP-WCGW
NP-WCMW
Dimensions (mm)
Insert Number
(2,3)
(2,3)
D4
L1
L3
F1
H1
Min. Standard
Cutting Corner
Diameter Radius
(mm)
(inch)
RR
D1
1.21p
122
25
2.9
17
5.8
.016
TS21
TKY06F
1.51.5p
125
33
15
.016
TS2
TKY06F
21.5p
125
10
15
10
.016
TS25
TKY08F
32.5p
12
180
15
11
13
16
.031
TS4
TKY15F
Clamp Torque (lbf-in) : TS21=5.3, TS2=5.3, TS25=8.9, TS4=31
E018
a
r

WCpp type inserts
A133, A134
CBN & PCD inserts
B049, B064
S-SWUC
WCooinserts
Steel shank
93
Finish
Light
Finish
R/L
FJ
Standard
(2,3)
(1.2,1.5)
Medium
CBN
(1.2,1.5,2,3)
MJ
(2,3)
R L
S-SWUCR/L-055
-065
-066
-062
-082
-103
-123
-163
1.21p
1.21p
WCMT 1.51.5p
21.5p
WCGT
NP-WCMW
21.5p
NP-WCGW
32.5p
32.5p
32.5p
a a
a a
a a
a a
a a
a a
a a
a a
Dimensions (inch)
Insert Number
D4
L1
F1
H1
.188
.250
.313
.375
.500
.625
.750
1.000
4.000
4.000
6.000
6.000
6.000
8.000
10.000
12.000
.114
.156
.188
.250
.312
.375
.500
.640
.172
.235
.295
.358
.480
.593
.725
.975
Wrench
TKY06F
TKY06F
TKY06F
TKY08F
TKY08F
TKY15F
TKY15F
TKY15F
BORING BARS
Stock
Order Number
(1.5,2,3)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
Re Clamp Screw
D1
TS21
.228 .016
17
TS2
17
.312 .016
TS2
15
.375 .016
TS25
15
.500 .016
TS25
13
.625 .016
TS4
10
.750 .031
TS4
8 1.000 .031
TS4
7 1.250 .031
(Note) When using inserts with right and left hand chip breakers, please use left hand inserts for right hand holders and right hand inserts for left hand holders.
C-SWLO
WCooinserts
Carbide shank
Finish
95
Light
Finish
R/L
FJ
Standard
(2)
(1.2,1.5)
Medium
CBN
(1.2,1.5,2)
MJ
Stock
Order Number
R L
C-SWLOR/L-055
-065
-066
-070
-062
a r
a r
a r
a r
a r
1.21p
WCMT
1.21p
WCGT
1.51.5p
NP-WCMW
21.5p
NP-WCGW
21.5p
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
Dimensions (inch)
Insert Number
(1.5,2)
(2)
D4
L1
F1
H1
.188
.250
.313
.375
.375
4.000
4.000
6.000
6.000
6.000
.114
.156
.188
.218
.250
.172
.235
.295
.358
.358
17
17
15
15
15
.228
.313
.375
.438
.500
.016
.016
.016
.016
.016
TS21
TS2
TS2
TS25
TS25
TKY06F
TKY06F
TKY06F
TKY08F
TKY08F
(Note) When using inserts with right and left hand chip breakers, please use left hand inserts for right hand holders and right hand inserts for left hand holders.
Clamp Torque (lbf-in) : TS21=5.3, TS2=5.3, TS25=8.9

Steel Shank
Heavy Metal Shank
Carbide Shank
Work Material
P
M
N
Carbon Steel
Alloy Steel
180 280HB
Stainless Steel
< 200HB
Aluminum Alloy
Light Cutting
Medium Cutting
Light Cutting
Medium Cutting
Light Cutting
Medium Cutting
Cutting Speed
(SFM)
l/d < 3
l/d < 3
l/d < 5
Feed
(IPR)
295 525
195 395
330 590
165 295
.002 .006
.006 .014
.002 .006
.006 .010
655 1310
490 820
.002 .006
.002 .006
Depth of Cut
(inch)

3 < l/d < 6
5 < l/d < 7
Cutting Speed
Feed
Depth of Cut
(inch)
(SFM)
(IPR)
.002 .006
.004 .008
.002 .006
.004 .008
.008
.059
.008
.079
260 490
165 360
330 590
130 260
.008
.079
655 1310
490 820
.002 .006
.002 .006
.008
.059
.008
.118
.008
.039
WCpp type inserts
A133, A134
SPARE PARTS
M001
CBN & PCD inserts
B049, B064
TECHNICAL DATA
N001
E019
BORING BARS
SCREW CLAMP TYPE
M-SWLO
a Two wall pocket.

a Screw-on type.
WCooinserts
Heavy metal shank
Finish
95
Light
Finish
FJ
R/L
Standard
(2,3)
(1.2,1.5)
Medium
CBN
(1.2,1.5,2,3)
MJ
Order Number
Stock
Dimensions (inch)
Insert Number
R L
L1
D4
F1
H1
(1.5,2,3)
(2,3)
Min.
Cutting
Diameter
(inch)
RR
D1
Standard
Corner
Radius
(inch)
a a
1.21p
.188
4.000
.114
.172
17
.228
.016
TS21
TKY06F
-065
a a
1.21p
.250
4.000
.156
.235
17
.313
.016
TS2
TKY06F
-066
a a
1.51.5p
.313
6.000
.188
.295
15
.375
.016
TS2
TKY06F
-070
a a
21.5p
.375
6.000
.218
.358
15
.438
.016
TS25
TKY08F
-062
a a
21.5p
.375
6.000
.250
.358
15
.500
.016
TS25
TKY08F
-082
a a
21.5p
.500
6.000
.312
.480
13
.625
.016
TS25
TKY08F
-103
a a
32.5p
.625
8.000
.375
.593
10
.750
.031
TS4
TKY15F
-123
a a
32.5p
.750
10.000
.500
.725
1.000
.031
TS4
TKY15F
-163
32.5p
1.000
12.000
.640
.975
1.250
.031
TS4
TKY15F
BORING BARS
M-SWLOR/L-055
WCMT
WCGT
NP-WCMW
NP-WCGW
M-SWLO
Heavy metal shank

coolant thru
WCooinserts
Finish
FJ
95
Light
Finish
R/L
Standard
(2,3)
(1.5)
Medium
CBN
(1.5,2,3)
MJ
Order Number
Stock
R L
D4
L1
(1.5,2,3)
Dimensions (inch)
Insert Number
(2,3)
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR
D1
F1
H1
M-SWLOR/L-066-C
a a
1.51.5p
.313
6.000
.188
.295
15
.375
.016
TS2
TKY06F
-070-C
a a
21.5p
.375
6.000
.218
.358
15
.438
.016
TS25
TKY08F
-062-C
a a
21.5p
.375
6.000
.250
.358
15
.500
.016
TS25
TKY08F
-082-C
a a
21.5p
.500
6.000
.312
.480
13
.625
.016
TS25
TKY08F
-103-C
a a
32.5p
.625
8.000
.375
.593
10
.750
.031
TS4
TKY15F
-123-C
a a
32.5p
.750
10.000
.500
.725
1.000
.031
TS4
TKY15F
-163-C
a a
32.5p
1.000
12.000
.640
.975
1.250
.031
TS4
TKY15F
WCMT
WCGT
NP-WCMW
NP-WCGW
E020
CUTTING CONDITIONS
E019
WCpp type inserts
A133, A134
CBN & PCD inserts
B050, B064
DOUBLE
CLAMP
DIMPLE BAR
S-DCLN
Steel shank
coolant thru
a Negative rake.
a New double clamp type.
a Holds inserts securely.
a Excellent cutting edge repeatability.
Finish
CNooinserts
FH
Light
Light
SA
SH
Medium
MA
95
F1
D
95
RR
Re
(4)
(3,4)
(4)
Medium
Stainless
CBN
MH
H1
L3
(4)
Medium
MS
Standard
D4
L1
6
R L
S-DCLNR/L-123-C
-163-C
-164-C
-204-C
-244-C
-284-C
-324-C
a a
a a
a a
a a
a a
a a
a a
D4
L1
L3
F1
(inch) (inch)
H1 RR D1
(4)
Re
*
Shim
Clamp
Shim Pin Bridge
Spring Clamp
Screw Wrench
CNMA 32p .750 10.000 1.219 .500 .711 12 1.000 .031 LLSCP32 LLP13 DCK2211 DCS2 DC0520T TKY15F
CNMG 32p 1.000 12.000 1.625 .641 .922 11 1.281 .031 LLSCP32 LLP13 DCK2211 DCS2 DC0520T TKY15F
43p 1.000 12.000 1.625 .641 .922 11 1.281 .031 LLSCP42 LLP14 DCK2613 DCS1 DC0621T TKY20F
43p 1.250 14.000 2.000 .766 1.171 13 1.532 .031 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
CNMA
CNMG
CNMM
CNGG
NP-CNMA
NP-CNGA
43p 1.500 14.000 2.000 .891 1.382 12 1.782 .031 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
43p 1.750 14.000 2.500 1.016 1.632 10 2.032 .031 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
43p 2.000 14.000 2.500 1.281 1.882 10 2.562 .031 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
BORING BARS
Dimensions (inch)
Insert Number
(3,4)
Standard
Corner Radius
Stock
Min. Cutting
Diameter
Order Number
(3,4)
(4)
S-DDUN
Steel shank
coolant thru
Finish
DNooinserts
FH
Finish
Light
FJ
SA
Medium
MA
93
F1
93
RR
Re
(4)
(4)
(4)
Medium
Stainless
CBN
MH
H1
L3
(4)
Medium
Standard
MS
D4
L1
6
(4)
Stock
R L
S-DDUNR/L-164-C
-204-C
-244-C
-284-C
-324-C
a a
a a
a a
a a
a a
Dimensions (inch)
Insert Number
D4
DNMA
DNMG
DNMX
DNGA
DNGG
NP-DNMA
NP-DNGA
L1
L3
F1
(inch) (inch)
H1 RR D1
(4)
(4)
Standard
Corner Radius
Order Number
Min. Cutting
Diameter
Re
(4)
*
Shim
Clamp
Shim Pin Bridge
Spring Clamp
Screw Wrench
43p 1.000 12.000 1.625 .657 .922 13 1.314 .031 LLSDP42 LLP14 DCK2613 DCS1 DC0621T TKY20F
43p 1.250 14.000 2.000 1.000 1.171 11 2.000 .031 LLSDN43 LLP14 DCK2613 DCS1 DC0621T TKY20F

Work Material
Hardness
Cutting
Mode
3 < l/d < 4
l/d < 3
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
P Carbon Steel, Alloy Steel 180 280HB Medium Cutting
360 (260 460)
.010 (.004 .016)
.197
360 (260 460)
.008 (.004 .012)
.157
Medium Cutting
260 (195 330)
.008 (.004 .012)
.157
230 (165 330)
.006 (.004 .015)
.118
Tensile Strength
Medium Cutting
< 350MPa
260 (195 330)
.010 (.004 .016)
.197
260 (195 330)
.008 (.004 .012)
.157
Stainless Steel
Cast Iron
< 200HB
CNpp type inserts
A068A072
DNpp type inserts
A074A078
SPARE PARTS
M001
CBN & PCD inserts
B022B027, B054
TECHNICAL DATA
N001
E021
BORING BARS
DOUBLE
CLAMP
DIMPLE BAR
S-DSKN
Steel shank
coolant thru
a Negative rake.
a New double clamp type.
a Holds inserts securely.
a Excellent cutting edge repeatability.
SNooinserts
Finish
Light
FH
SA
Medium
MA
Medium
MH
F1
D
75
75
RR
Re
H1
L3
(4)
(4)
(4)
(4)
Medium
Stainless
G Class
CBN
MS
Standard
R/L
D4
L1
(4)
Stock
Dimensions (inch)
Insert Number
R L
a a
-204-C
a a
-244-C
a a
-284-C
a a
-324-C
a a
BORING BARS
S-DSKNR/L-164-C
D4
L1
L3
F1
(inch) (inch)
H1 RR D1
(4)
(4)
Standard
Corner Radius
Order Number
Min. Cutting
Diameter
Re
(4)
*
Shim
Clamp
Shim Pin Bridge
Spring Clamp
Screw Wrench
43p 1.000 12.000 1.625 .641 .922 13 1.282 .031 LLSSP42 LLP14 DCK2613 DCS1 DC0621T TKY20F
SNMA
SNMG
SNMM
SNGA
SNGG
NP-SNMA
NP-SNGA
43p 1.250 14.000 2.000 .766 1.171 13 1.532 .031 LLSSN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
43p 1.500 14.000 2.000 .891 1.382 11 1.782 .031 LLSSN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
43p 1.750 14.000 2.500 1.016 1.632 10 2.032 .031 LLSSN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
43p 2.000 14.000 2.500 1.281 1.882 9 2.562 .031 LLSSN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
S-DTFN
Steel shank
coolant thru
TNooinserts
Finish
Light
FH
SA
Medium
MA
Medium
MH
F1
D 91
91
RR
Re
H1
L3
(3)
(3,4)
(3,4)
(3,4)
Medium
Stainless
G Class
CBN
MS
Standard
R/L
D4
L1
(3,4)
Stock
Dimensions (inch)
Insert Number
R L
D4
L1
L3
F1
(inch) (inch)
H1 RR D1
(3,4)
(3)
Standard
Corner Radius
Order Number
Min. Cutting
Diameter
Re
(3)
*
Shim
Clamp
Shim Pin Bridge
Spring Clamp
Screw Wrench
S-DTFNR/L-123-C
a a
33p
-163-C
a a
33p 1.000 12.000 1.625 .641 .922 13 1.282 .031 LLSTP32 LLP13 DCK2211 DCS2 DC0520T TKY15F
-203-C
a a
-243-C
a a
-244-C
a a
-283-C
a a
-284-C
a a
43p 1.750 14.000 2.500 1.016 1.632 11 2.032 .031 LLSTN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
-324-C
a a
TNMA
TNMG
TNMM
TNGA
TNGG
NP-TNMA
NP-TNGA
.750 10.000 1.250 .500 .711 13 1.000 .031
DCK2211 DCS2 DC0520T TKY15F
33p 1.250 14.000 2.000 .766 1.171 13 1.532 .031 LLSTN32 LLP13 DCK2211 DCS2 DC0520T TKY15F
E022
SNpp type inserts
A080A084
TNpp type inserts
A085A091
CBN & PCD inserts
B028B031, B055
S-DVUN
Steel shank
coolant thru
1
Finish
VNooinserts
Light
FJ
SH
Medium
MA
F1
93
RR
93
Finish
FH
H1
L3
Re
(3)
(3)
(3)
Medium
Stainless
CBN
MH
(3)
MS
D4
L1
5
(3)
Dimensions (inch)
Insert Number
R L
L1
D4
L3
F1
(inch) (inch)
H1 RR D1
(3)
Re
*
Shim
Clamp
Shim Pin Bridge
Spring Clamp
Screw Wrench
VNMA
VNMG 33p 1.250 14.000 2.000 1.000 1.171 10 2.000 .031 DCSVN32 LLP13 DCK3113 DCS2 DC0520T TKY15F
VNGA
VNGM
a
a
NP-VNMA
33p 1.500 14.000 2.500 1.125 1.382 9 2.250 .031 DCSVN32 LLP13 DCK3113 DCS2 DC0520T TKY15F
-243-C
NP-VNGA
S-DVUNR/L-203-C
a a
S-DWLN
Steel shank
coolant thru
WNooinserts
Finish
Light
FH
SA
BORING BARS
Stock
(3)
Standard
Corner Radius
Order Number
Min. Cutting
Diameter
Medium
MA
95
F1
D 95
RR
Re
(4)
CBN
(3,4)
MS
H1
L3
(4)
Stainless
D4
L1
6
Stock
Dimensions (inch)
Insert Number
R L
D4
L1
L3
F1
(inch) (inch)
H1 RR D1
(3,4)
(4)
Standard
Corner Radius
Order Number
Min. Cutting
Diameter
Re
*
Shim
Clamp
Shim Pin Bridge
Spring Clamp
Screw Wrench
S-DWLNR/L-123-C
a a
-163-C
a a
33p 1.000 12.000 1.750 .641 .922 13 1.282 .031 LLSWP32 LLP13 DCK2211 DCS2 DC0520T TKY15F
-164-C
a a
43p 1.000 12.000 2.000 .641 .922 13 1.282 .031 LLSWP42 LLP14 DCK2613 DCS1 DC0621T TKY20F
-204-C
a a
-244-C
a a
-284-C
a a
WNMA 43p 1.250 14.000 2.000 .766 1.171 13 1.532 .031 LLSWN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
WNMG
43p 1.500 14.000 2.500 .891 1.382 12 1.782 .031 LLSWN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
NP-WNMA
NP-WNGA 43p 1.750 14.000 2.500 1.125 1.632 11 2.250 .031 LLSWN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
-324-C
a a
43p 2.000 14.000 2.500 1.281 1.882 10 2.562 .031 LLSWN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
WNMG
33p
.750 10.000 1.250 .500 .711 12 1.000 .031
DCK2211 DCS2 DC0520T TKY15F

Work Material
Hardness
Cutting
Mode
3 < l/d < 4
l/d < 3
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
P Carbon Steel, Alloy Steel 180 280HB Medium Cutting
360 (260 460)
.010 (.004 .016)
.197
360 (260 460)
.008 (.004 .012)
.157
Medium Cutting
260 (195 330)
.008 (.004 .012)
.157
230 (165 330)
.006 (.004 .015)
.118
Tensile Strength
Medium Cutting
< 350MPa
260 (195 330)
.010 (.004 .016)
.197
260 (195 330)
.008 (.004 .012)
.157
Stainless Steel
Cast Iron
< 200HB
VNpp type inserts
A092, A093
WNpp type inserts
A094A097
SPARE PARTS
M001
CBN & PCD inserts
B032B034, B056
TECHNICAL DATA
N001
E023
BORING BARS
MULTIPLE CLAMP TYPE
S-MCLN
a Negative rake.
a Two wall pocket.
a Pin lock and top clamp
retention.
CNooinserts
Steel shank
Finish
FH
95
Order Number
Insert Number
R L
D4
L1
F1
H1
Medium
MA
(4)
(4)
(3,4)
(4,6)
Medium
Stainless
CBN
MS
Standard
(3,4,6)
(4,6)
Dimensions (inch)
Light
SH
Medium
MH
Stock
Light
SA
(3,4,6)
(4)
*3
Min.
Cutting
Diameter
(inch)
RR
D1
*3
Shim
a a
32p
.750
10.000
.500
.700
14
1.000
NL33
CL7
-163
a a
32p
1.000
12.000
.640
.910
14
1.280
NL33
CL7
XNS36
-164
a a
1.000
12.000
.640
.910
14
1.280
NL44
CL20
XNS47
-204
a a
1.250
12.000
.765
1.160
14
* NL46
1.530 ICSN433
CL20
XNS47
BORING BARS
S-MCLNR/L-123
-244
a a
-284
a a
-326
a a
CNMA
2
CNMG 43p*
2
CNMM
43p*
CNGG
2
NP-CNMA 43p*
2
NP-CNGA
43p*
64p
1.500
14.000
.890
1.410
XNS36
14
* NL46
1.780 ICSN433
CL20
XNS47
CL20
XNS47
CL12
XNS510
1.750
14.000
1.015
1.660
12
*1 NL46
2.030 ICSN433
2.000
14.000
1.281
1.910
12
2.562 ICSN633 NL68
1 (Opt.) See page M009 for different radius.
3 Clamp Torque (lbf-in) : NL33=13, NL44=19, NL46=19, NL68=43,
Shim Screw
S46
Chipbreaker
CBC4
XNS36=30, XNS47=45, XNS510=70
*
*
S-MDUN
DNooinserts
Steel shank
93
Finish
FH
Order Number
Insert Number
R L
S-MDUNR/L-204
a a
-244
a a
-284
a a
-285
-324
a a
-325
DNMA
DNMG
DNMM
DNGM
DNGA
DNGG
NP-DNMA
NP-DNGA
Medium
MA
(4)
(4)
(4)
(4)
Medium
Stainless
CBN
MS
Standard
(4)
Dimensions (inch)
Light
SA
Medium
MH
Stock
Finish
FJ
Min.
Cutting
Diameter
(inch)
RR
D1
(4)
(4)
(4)
*2
*2
Shim
D4
L1
F1
H1
43p
1.250
12.000
1.000
1.160
10
2.000 IDSN433 NL46
CL12
XNS59
43p
1.500
14.000
1.125
1.410
10
2.250 IDSN433 NL46
CL12
XNS59
43p
1.750
14.000
1.250
1.660
10
2.500 IDSN433 NL46
CL12
XNS59
CL30
XNS510
CL12
XNS59
CL30
XNS510
1
54p* 1.750
14.000
1.375
1.660
10
*1 NL58
2.750 IDSN533
43p
14.000
1.375
1.910
10
2.750 IDSN433 NL46
10
* NL58
3.000 IDSN533
54p*
2.000
1
2.000
14.000
1.500
1.910
1 (Opt.) See page M009 for different thickness.
2 Clamp Torque (lbf-in) : NL46=19, NL58=29, XNS59=70, XNS510=70
*
*
E024
CNpp type inserts
A068A073
DNpp type inserts
A074A078
CBN & PCD inserts
B022B027, B054
S-MSKN
Finish
SNooinserts
Steel shank
FH
75
Order Number
Insert Number
R L
L1
D4
F1
(4)
(4,6)
(4,6)
Stainless
G Class
CBN
MS
(4,6)
R/L
(4,6)
(4)
(4)
*3
*3
Min.
Cutting
Diameter
(inch)
RR
D1
H1
Medium
MH
(4)
Dimensions (inch)
Medium
MA
Medium
Standard
Stock
Light
SA
Shim
SNMA 43p *12 1.250 12.000

*1 NL46 CL9
XNS59
.765 1.160 14 1.530 ISSN433
*1
SNMG
1
*
a a SNMM 43p *2 1.500
XNS59
14.000
.890 1.410 14 1.780 ISSN433 NL46 CL9
*1
SNGA
*1 NL46 CL9
a a SNGG 43p *2 1.750
XNS59
14.000 1.015 1.660 12 2.030 ISSN433
*1
NP-SNMA
*1 NL68 CL12 XNS58
a a NP-SNGA 64p *
2.000 14.000 1.281 1.910 12 2.562 ISSN633
1 (Opt.) See page M009 for different thickness or radius.
3 Clamp Torque (lbf-in) : NL46=19, NL68=43, XNS58=70, XNS59=70
Shim Screw
S34
Chipbreaker
CBS4
S-MSKNR/L-204
-244
-284
-326
*
*
S-MTFN
Finish
TNooinserts
Steel shank
FH
90
Order Number
Insert Number
R L
S-MTFNR/L-163X
-203X
-243X
-244
-283X
-284
-324
a a
a a
a a
a a
r
a a
a a
D4
(3,4)
(3,4)
(3,4)
Stainless
G Class
CBN
MS
(3,4)
Min.
Cutting
Diameter
(inch)
RR
D1
R/L
(3,4)
(3,4)
(3)
*3
*3
Shim
L1
F1
H1
33p *12 1.000

*
TNMA
33p *12 1.250
*1
TNMG
TNMM 33p *2 1.500
12.000
12.000
.640
.765
.910
1.160
15
12
* NL34L
1.280 ITSN323
*1 NL34L
1.530 ITSN323
14.000
.890
1.410
10
TNGA 43p *
TNGG 33p *12
*1
NP-TNMA
43p *
NP-TNGA
1
43p *
1.500
14.000
1.031
1.410
10
* NL34L
1.780 ITSN323
*1 NL46
2.062 ITSN432
1.750
14.000
1.015
1.660
10
1.750
2.000
14.000
14.000
1.156
1.281
1.660
1.910
8
8
*1
Medium
MH
(3)
Dimensions (inch)
Medium
MA
Medium
Standard
Stock
Light
SA
BORING BARS
a a
* NL34L
2.030 ITSN323
*1 NL46
2.312 ITSN432
*1 NL46
2.562 ITSN432
CL7
XNS35
CL7
XNS35
CL7
XNS35
CL9
XNS59
CL7
XNS35
CL9
XNS59
CL9
XNS59
1 (Opt.) See page M009 for different thickness or radius.
3 Clamp Torque (lbf-in) : NL34L=13, NL46=19, XNS35=30, XNS59=70
Shim Screw
S34
Chipbreaker
CBT3
*
*

Work Material
Hardness
P Carbon Steel, Alloy Steel 180 280HB

M
K
Stainless Steel
< 200HB
Cast Iron
Tensile Strength
< 350MPa
Cutting
Mode
Medium
Cutting
Medium
Cutting
Medium
Cutting
3 < l/d < 4
l/d < 3
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
260 460
.004 .016
.20
260 460
.004 .012
.16
200 330
.008 .012
.16
165 330
.004 .015
.12
200 330
.004 .016
.20
200 330
.004 .012
.16
SNpp type inserts
A080A084
TNpp type inserts
A085A091
SPARE PARTS
M001
CBN & PCD inserts
B028B031, B055
TECHNICAL DATA
N001
E025
BORING BARS
MULTIPLE CLAMP TYPE
S-MVUN
a Negative rake.
a Two wall pocket.
a Pin lock and top clamp
retension.
Finish
VNooinserts
Steel shank
FH
93
Order Number
Insert Number
R L
BORING BARS
S-MVUNR/L-203
a r
-243
-284
-324
VNMG
VNGA
VNGG
VNGM
NP-VNMA
NP-VNGA
33p
33p
43p*
43p*
Medium
MA
(3)
(3)
(3)
Stainless
CBN
(3)
MS
(3)
Dimensions (inch)
Light
SH
Medium
MH
Stock
Finish
FJ
Min.
Cutting
Diameter
(inch)
RR
D1
(3)
(3)
*2
*2
Shim
D4
L1
F1
H1
1.250
14.000
1.125
1.16
12
2.250 IVSN322 NL34L
CL12
XNS58
1.500
14.000
1.250
1.41
12
2.500 IVSN322 NL34L
CL12
XNS58
12
* NL46
3.000 IVSN432
CL12
XNS59
CL12
XNS59
1.750
2.000
14.000
16.000
1.500
1.625
1.66
1.91
12
1
1
* NL46
3.250 IVSN432
1 (Opt.) See page M009 for different radius.
2 Clamp Torque (lbf-in) : NL34L=13, NL46=19, XNS58=70, XNS59=70
*
*
S-MWLN
Finish
WNooinserts
Steel shank
FH
95
Order Number
Stock
Dimensions (inch)
Insert Number
R L
(4)
(4)
Medium
Stainless
MA
D4
L1
F1
H1
Min.
Cutting
Diameter
(inch)
RR
D1
Light
SA
MS
(3,4)
(3,4)
*
Shim
S-MWLNR/L-123
a a
32p
.750
10.000
.500
.700
14
1.000
NL33
CL7
XNS36
-163
a a
1.000
12.000
.640
.910
14
1.280
NL33
CL7
XNS36
-164
a a
1.000
12.000
.640
.910
14
1.280
NL44
CL20
XNS47
-204
a a
32p
WNMA
WNMG 43p
NP-WNMA
43p
1.250
12.000
.765
1.160
14
1.530 IWSN432 NL46
CL20
XNS48
-244
a a
43p
1.500
14.000
.890
1.410
14
1.780 IWSN432 NL46
CL20
XNS48
Clamp Torque (lbf-in) : NL33=13, NL44=19, NL46=19, XNS36=30, XNS47=45, XNS48=45
E026
VNpp type inserts
A092, A093
WNpp type inserts
A094, A097
CBN & PCD inserts
B032B034, B056
Heavy metal shank

coolant thru
Finish
WNooinserts
FH
95
Stock
Order Number
M-MWLNR/L-164-C
a a
-204-C
a a
-244-C
a a
43p
WNMA
WNMG 43p
NP-WNMA
43p
Min.
Cutting
Diameter
(inch)
RR
D1
Dimensions (inch)
Insert Number
R L
(4)
(4)
Stainless
Stainless
MA
Light
SA
MS
(4)
(4)
*
Shim
D4
L1
F1
H1
1.000
12.000
.640
.955
14
1.280
NL44
CL20
XNS47
1.250
12.000
.765
1.205
14
1.530 IWSN432 NL46
CL20
XNS48
1.500
14.000
.890
1.455
14
1.780 IWSN432 NL46
CL20
XNS48
Clamp Torque (lbf-in) : NL44=19, NL46=19, XNS47=45, XNS48=45
BORING BARS
M-MWLN

Work Material
Hardness
Cutting
Mode
3 < l/d < 4
l/d < 3
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
P Carbon Steel, Alloy Steel 180 280HB
Medium
Cutting
260 460
.004 .016
.20
260 460
.004 .012
.16
Medium
Cutting
Medium
Cutting
200 330
.008 .012
.16
165 330
.004 .010
.12
200 330
.004 .016
.20
200 330
.004 .012
.16
Stainless Steel
< 200HB
Cast Iron
Tensile Strength
< 350MPa
WNpp type inserts
A094A097
SPARE PARTS
M001
CBN & PCD inserts
B034
TECHNICAL DATA
N001
E027
BORING BARS
AL
a Shank sizes & .625inch thru & 1.000inch.

a Screw-on type.
a Recommended for aluminum, nonferrous
TYPE
BORING BARS
S-STFE
metals and plastics.
TEooinserts
Steel shank
Medium
R/L
(3)
PCD
91
R/L
Stock
Order Number
Insert Number
BORING BARS
R L
S-STFER/L-103
a a
-123
a a
-163
a a
L1
D4
TEGX
Min. Standard
Cutting Corner
Diameter Radius
(inch) (inch)
RR D1
Dimensions (inch)
L2
F1
H1
32p
.625
8.000 1.250
.406
.560
.813
.016 FC400890T TKY10F
32p
.750 10.000 1.500
.500
.700
1.000
.016 FC400890T TKY10F
32p
1.000 12.000 1.625
.641
.910
1.281
.016 FC400890T TKY10F

Work Material
Aluminum Alloy
Grade
Cutting Speed
(SFM)
HTi10
655 1970
l/d=3
Feed
D.O.C
(IPR)
(inch)
.002 .010
.12
l/d=4
D.O.C
Feed
(inch)
(IPR)
.002 .010
.12
l/d=5
Feed
D.O.C
(IPR)
(inch)
.002 .008
.10
l/d=6
Feed
D.O.C
(IPR)
(inch)
.002 .008
.039
E028
TEpp type inserts
A121
CBN & PCD inserts
B065
a The
minimum cutting diameter

a 7positive insert.
MICRO-DEX
SCLC

CCooinserts
Carbide shank
Finish
LF
95
(03,04)
CBN
Stock
R
C04GSCLCR03
C05HSCLCR03
C06JSCLCR04
C07KSCLCR04
Dimensions (mm)
Insert Number
CCGT
NP-CCMW
D4
L1
F1
H1
RR
03S1ppL-F
90
2.5
3.7
15
0.2
TS16
TKY06F
03S1ppL-F
100
3.0
4.7
13
0.2
TS16
TKY06F
04T0ppL-F
110
3.5
5.7
13
0.2
TS21
TKY06F
0.2
TS21
TKY06F
04T0ppL-F
125
4.0
6.7
11
BORING BARS
Order Number
(03,04)
Min. Standard
Cutting Corner
Diameter Radius
(mm)
(mm)
D1
SWUB
WBGT inserts
Carbide shank
Finish
LF
93
(1.2,1.5)
Order Number
Stock
R
C05HSWUBR02
C06JSWUBR02
C07KSWUBRL3
Dimensions (mm)
Insert Number
WBGT
Min. Standard
Cutting Corner
Diameter Radius
(mm)
(mm)
D1
D4
L1
F1
H1
RR
1.21ppLF
100
3.0
4.7
15
0.2
TS21
TKY06F
1.21ppLF
110
3.5
5.7
13
0.2
TS2C
TKY06F
1.51.5ppLF
125
4.0
6.7
15
0.2
TS2
TKY06F
Clamp Torque (lbf-in) : TS21=5.3, TS2C=5.3, TS2=5.3

Work Material
Grade
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
l/d
General Steel
NX2525
130 395
.0004 .002
.004 .012
35
Stainless Steel
VP15TF
130 395
.0004 .002
.004 .012
35
Cast Iron
VP15TF
130 395
.0004 .002
.004 .012
35
VP15TF
260 525
.0004 .002
.004 .024
35
MD220
260 525
.0004 .002
.004 .024
35
N
Non-Ferrous Material
CCGT type inserts
A102
WBGT type inserts
A132
SPARE PARTS
M001
CBN & PCD inserts
B040, B058
TECHNICAL DATA
N001
E029
BORING BARS
minimum cutting diameter
a 7positive insert.
MICRO-DEX
STUC

a The
TCGT inserts
Carbide shank
Finish
LF
(1.2)
93
Order Number
Stock
Insert Number
BORING BARS
C07KSTUCR06
Dimensions (mm)
TCGT
1.21ppLF
D4
L1
F1
H1
RR
125
4.0
6.7
12
Min. Standard
Cutting Corner
Diameter Radius
(mm)
(mm)
D1
0.2
TS2C
TKY06F
* Clamp Torque (lbf-in) : TS2C=5.3

Work Material
Grade
Cutting Speed
(SFM)
Feed
(IPR)
Depth of Cut
(inch)
l/d
General Steel
NX2525
130 395
.0004 .002
.004 .012
35
Stainless Steel
VP15TF
130 395
.0004 .002
.004 .012
35
Cast Iron
VP15TF
130 395
.0004 .002
.004 .012
35
VP15TF
260 525
.0004 .002
.004 .024
35
MD220
260 525
.0004 .002
.004 .024
35
N
E030
: Inventory maintained. (1 MICRO-MINI in one case)
TCGT type inserts
A119
MICRO-MINI
Solid carbide type (Single cutting edges).

Cutting edge can be shaped according to the application.
Thus, it covers a wide cutting range (threading,grooving,copying, etc.).
STANDARD MICRO-MINI BORING BARS

Geometry
(Solid carbide boring bar)

Stock
a
a
a
Order Number
D4 Shank diameter
Flat area
Flat area
Dimensions (mm)
Min.
Max.
Cutting Depth of
Diameter Groove
(mm)
(mm)
F2
TF15
W3
D4
L1
L2
C03FR-BLS
2.0
80
15
3.2
1.0
C04FR-BLS
2.5
80
20
4.2
1.5
C05HR-BLS
3.0
100
25
5.2
2.0

Work Material
Cutting Speed (SFM)
Feed (IPR)
Depth of Cut (inch)
l/d
General Steel
100 165
.004
.004 .012
Stainless Steel
100 165
.004
.004 .012
Cast Iron
100 165
.002
200 330
.004
Cutting Edge Preparation

Corner Radius or C
Honing
.004 .020
.0004 .002
< .016
< .001
(Honing not required)
.004 .012
.004 .020
.0004 .002
.004 .020
.004 .020
< .001
(Honing not required)
BORING BARS
Right hand tool only.
* Cutting edge is not honed. Please hone according to the workpiece before machining.
GRINDING THE CUTTING EDGE OF MICRO-MINI BORING BAR
Grooving
Boring
Threading
Groove width
(Grinding)
Grinding Examples
Application
aMICRO-MINI boring bar can be applied to boring and grooving without any modications. It can also be reground as shown below.
aFor shaping and regrinding, use diamond wet stone approximately #250 - #400. Please grind according to application using the gure below as a reference.
Thread angle
Grinding
Grinding
Grinding
Grinding
.0118" .0197" Corner radius

(Grinding)
6 Double sided relief
SPARE PARTS
M001
TECHNICAL DATA
N001
E031
BORING BARS
MICRO-MINI TWIN
CB
For boring
Re0.015
D4
F2
F1
H1
L1
L2
L3
Order Number
BORING BARS
CB02RS
E032
Stock
Micro Grain Coated
Carbide
TF15 VP15TF
Breaker
Min. Cutting Diameter

(mm)
Dimensions (mm)
l/d<3
l/d>3
Re
D4
L1
L2
L3
F1
F2
H1
Without
2.2
3.6
0.05
50
0.25
1.8
1.4
02RS-B
With
2.2
3.9
0.05
50
0.25
1.8
1.4
02RS-01
Without
2.2
3.6
0.1
50
0.25
1.8
1.4
02RS-01B
With
2.2
4.2
0.1
50
0.25
1.8
1.4
02RS-02
Without
2.2
3.6
0.2
50
0.25
1.8
1.4
02RS-02B
With
2.2
4.9
0.2
50
0.25
1.8
1.4
03RS
Without
3.2
4.2
0.05
50
7.5
1.5
0.35
2.7
2.3
03RS-B
With
3.2
4.4
0.05
50
7.5
1.5
0.35
2.7
2.3
03RS-01
Without
3.2
4.2
0.1
50
7.5
1.5
0.35
2.7
2.3
03RS-01B
With
3.2
4.5
0.1
50
7.5
1.5
0.35
2.7
2.3
03RS-02
Without
3.2
4.2
0.2
50
7.5
1.5
0.35
2.7
2.3
03RS-02B
With
3.2
4.8
0.2
50
1.5
0.35
2.7
2.3
04RS
Without
4.2
5.1
0.05
60
10
12
0.45
3.6
3.1
04RS-B
With
4.2
5.2
0.05
60
10
12
0.45
3.6
3.1
04RS-01
Without
4.2
5.1
0.1
60
10
12
0.45
3.6
3.1
04RS-01B
With
4.2
5.3
0.1
60
10
12
0.45
3.6
3.1
04RS-02
Without
4.2
5.1
0.2
60
10
12
0.45
3.6
3.1
04RS-02B
With
4.2
5.5
0.2
60
10
12
0.45
3.6
3.1
05RS
Without
5.2
6.0
0.05
70
12.5
15
2.5
0.55
4.5
3.9
05RS-B
With
5.2
6.1
0.05
70
12.5
15
2.5
0.55
4.5
3.9
05RS-02
Without
5.2
6.0
0.2
70
12.5
15
2.5
0.55
4.5
3.9
05RS-02B
With
5.2
6.4
0.2
70
12.5
15
2.5
0.55
4.5
3.9
06RS
Without
6.2
7.2
0.05
75
12.5
18
0.65
5.4
4.7
06RS-B
With
6.2
7.3
0.05
75
12.5
18
0.65
5.4
4.7
06RS-02
Without
6.2
7.2
0.2
75
12.5
18
0.65
5.4
4.7
06RS-02B
With
6.2
7.8
0.2
75
12.5
18
0.65
5.4
4.7
07RS
Without
7.2
8.6
0.05
85
12.5
21
3.5
0.75
6.3
5.5
07RS-B
With
7.2
8.8
0.05
85
12.5
21
3.5
0.75
6.3
5.5
07RS-02
Without
7.2
8.6
0.2
85
12.5
21
3.5
0.75
6.3
5.5
07RS-02B
With
7.2
9.2
0.2
85
12.5
21
3.5
0.75
6.3
5.5
The Re dimension represents the size before grinding a chip breaker.
: Inventory maintained. (1 MICRO-MINI TWIN in one case)
7.5
CR
For copying
F1
52
D1
Re
L10
H1
L1
D4
L2
Breaker
Min.Cutting
Diameter
(mm)
D1
Dimensions (mm)
Re
D4
L1
L10
L2
F1
H1
Without
3.5
0.1
50
0.15
2.7
03RS-01B
With
3.5
0.1
50
0.15
2.7
04RS-01
Without
4.5
0.1
60
10
0.15
3.6
04RS-01B
With
4.5
0.1
60
10
0.15
3.6
05RS-01
Without
5.5
0.1
70
12
0.15
4.5
05RS-01B
With
5.5
0.1
70
12
0.15
4.5
CR03RS-01
BORING BARS
Order Number
Stock
Micrograin
Carbide Coated
TF15 VP15TF
y NOTES
Prole turning, Inner end facing
Copying
The cutting edge

should not be cross
the center line of the
workpiece.
The depth of cut

should be smaller
than the corner
Depth of cut
radius value.
If the cutting edge crosses the center line of a workpiece,

the cutting edge can fracture.
With depths of cut larger than the corner radius value,

burrs will be formed.
y RECOMMENDED TOOL OVERHANG

MICRO-MINI TWIN
CR type
Holder

Work Material
Cutting Speed
(SFM)
Feed
(IPR)
CB Type
Depth of Cut
(inch)
CR Type
Feed (IPR)
Overhang
(l/d)
Cutting Speed
(SFM)
03RS/04RS
05RS
General Steel
130 395
.0004 .002
.004 .012
35
130 395
.0004 .001
.0004 .002
Stainless Steel
130 395
.0004 .002
.004 .012
35
130 395
.0004 .001
.0004 .002
Cast Iron
130 395
.0004 .002
.004 .012
35
130 395
.0004 .002
.0004 .002
Non Ferrous Materials
260 525
.0004 .003
.004 .020
35
260 525
.0004 .002
.0004 .003
SPARE PARTS
M001
TECHNICAL DATA
N001
(Note) Recommend wet machining.
E033
BORING BARS
HOLDER (INCH SHANK STANDARD)
RBH
z
D4
10mm
20mm
PT1/8 z
c
L1
3-M4 x .7
S2
RBH16pppA
(Coolant thru)
10mm
c
L1
3-M4 x .7
5mm S1 S2
D8
PT1/8
D4
5mm S1
D5
3-M4 x .7
D4
S2
D5
5mm S1
D5
D8
Round type holder
10mm
c
L1
RBH190ppN
RBH10pppA, RBH12pppA
(Coolant thru)
y ID (& D8) : INCH TYPE

Dimensions
BORING BARS
Order Number
RBH10300A
10350A
10400A
10500A
RBH12300A
12350A
12400A
12500A
RBH16300A
16350A
16400A
16500A
Stock
Clamp Screw
Wrench
D4
D8
D5
L1
S1
S2
(inch)
(inch)
(mm)
(mm)
(mm)
(mm)
.625
.625
.187
100
100
15
15
.219
15
15
15
15
A
A
HKY20F
HKY20F
.625
.250
15
100
20
20
.625
.313
15
100
20
20
A
D
HKY20F
a
a
.750
.187
125
15
.219
15
HKY20F
.750
.750
.250
18
125
125
B
B
HKY20F
.750
15
15
18
18
125
20
B
A
HKY20F
HKY20F
1.000
1.000
18
14
20
20
20
.313
.187
150
15
15
HKY20F
.219
15
150
15
HKY20F
1.000
1.000
.250
.313
16
150
150
15
20
C
C
20
20
20
C
C
HKY20F
HKY20F
a
a
a
a
a
17
HKY20F
Torque
(lbf-in)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
y ID (& D8) : METRIC TYPE

Dimensions
Order Number
RBH10126A
10189A
10252A
10315A
10378A
10441A
RBH19020N
19030N
19040N
19050N
19060N
19070N
RBH16126A
16189A
16252A
16315A
16378A
16441A
Stock
Clamp Screw
Wrench
D4
D8
D5
L1
S1
S2
(inch)
(mm)
(mm)
(mm)
(mm)
(mm)
2
3
15
15
100
100
10
10
HKY20F
10
HKY20F
15
100
100
15
15
HKY20F
15
15
HKY20F
20
20
20
20
A
A
A
A
A
A
HKY20F
HKY20F
C
B
HKY20F
HKY20F
.625
a
a
.625
.625
.625
15
15
15
.625
.625
.750
6
2
125
.750
18
18
125
10
10
.750
18
15
HKY20F
18
15
15
HKY20F
.750
.750
125
125
10
15
18
125
15
15
.750
18
125
20
B
B
B
B
B
B
HKY20F
11
10
A
A
B
B
HKY20F
HKY20F
1.000
12
13
150
150
10
1.000
1.000
20

15
HKY20F
1.000
14
150
1.000
20
A
A
1.000
15
16
150
6
7
15
20
15
150
20
20
a
a
100
100
150
10
15
* Order number of clamp screw A=HSS04004, B=HSS04006, C=HSS04008, D=HSS04003
E034
HKY20F
Torque
(lbf-in)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
HKY20F
C
C
C
C
HKY20F
18 (2.0N.m)
18 (2.0N.m)
18 (2.0N.m)
HKY20F
18 (2.0N.m)
HOLDER CROSS REFERENCE LIST OF INCH SHANK STANDARD

Holder
MICRO-MINI TWIN
MICRO-MINI
Machine Makers
MICRO-DEX
Order Number
10189A
10252A
10315A
10378A
10441A
ID : Inch Type
Round
Type
Holder
& .625
inch
ID : Metric Type
RBH10126A
10350A
10400A
ID : Metric Type
19030N
19040N
19050N
19060N
ID : Inch Type
19070N
ID : Metric Type
03RS-01
03RS-01B
04RS-01
04RS-01B
05RS-01
05RS-01B
03FR-BLS
C04GSpppRpp 04FR-BLS
C06GSpppRpp
Citizen Precision Machinery

Co., Ltd.
C07GSpppRpp
NC lathes
For DIMPLE BAR and SCREW CLAMP TYPE
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
03RS-01
03RS-01B
04RS-01
04RS-01B
05RS-01
05RS-01B
03FR-BLS
C06GSpppRpp
C07GSpppRpp

Co., Ltd.
RBH12300A
12350A
12400A
12500A
16189A
16252A
16315A
16378A
16441A
ID : Inch Type
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
10500A
RBH16126A
Round
Type
Holder
& 1.000
inch
CR
RBH10300A
RBH19020N
Round
Type
Holder
& .750
inch
CB
BORING BARS
Type
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
03RS-01
03RS-01B
04RS-01
04RS-01B
05RS-01
05RS-01B
03FR-BLS

Co., Ltd.
C05GSpppRpp 05FR-BLS NC lathes

C06GSpppRpp
C07GSpppRpp
RBH16300A
16350A
16400A
16500A
Mitsubishi Materials obtained the makers' approval before entering their names in the list.
SPARE PARTS
M001
TECHNICAL DATA
N001
E035
BORING BARS
HOLDER (METRIC SHANK STANDARD)
RBH
Round type holder
5mm S1
S2
RBH20ppN
RBH25ppN
3-M4 x .7
D8
10mm
20mm
10mm
c
L1
RBH22ppN
RBH16ooN
BORING BARS
L1
Dimensions (mm)
Clamp Screw
Stock
D4
D8
D5
L1
S2
3-M4 x .7
D5
5mm S1
z
S1
S2
S3
10mm
S3
20mm
Wrench
x
L1
Torque
(lbf-in)
RBH1620N
16
15
100
10
HKY20F 18 (2.0Nm)
1630N
16
15
100
10
10
HKY20F 18 (2.0Nm)
1640N
16
15
100
15
15
HKY20F 18 (2.0Nm)
1650N
16
15
100
15
15
HKY20F 18 (2.0Nm)
1660N
16
15
100
15
15
HKY20F 18 (2.0Nm)
1670N
16
15
100
20
20
HKY20F 18 (2.0Nm)
RBH2020N
20
11
125
10
HKY20F 18 (2.0Nm)
2030N
20
12
125
10
10
HKY20F 18 (2.0Nm)
2040N
20
13
125
15
15
HKY20F 18 (2.0Nm)
2050N
20
14
125
15
15
HKY20F 18 (2.0Nm)
2060N
20
15
125
15
15
HKY20F 18 (2.0Nm)
2070N
20
16
125
20
20
HKY20F 18 (2.0Nm)
RBH2220N
22
11
125
10
10
HKY20F 18 (2.0Nm)
2230N
22
12
125
10
10
10
HKY20F 18 (2.0Nm)
2240N
22
13
125
15
15
12.5
HKY20F 18 (2.0Nm)
2250N
22
14
125
15
15
12.5
HKY20F 18 (2.0Nm)
2260N
22
15
125
15
15
15
HKY20F 18 (2.0Nm)
2270N
22
16
125
20
20
15
HKY20F 18 (2.0Nm)
RBH2520N
25
11
150
10
HKY20F 18 (2.0Nm)
2530N
25
12
150
10
10
HKY20F 18 (2.0Nm)
2540N
25
13
150
15
15
HKY20F 18 (2.0Nm)
2550N
25
14
150
15
15
HKY20F 18 (2.0Nm)
2560N
25
15
150
15
15
HKY20F 18 (2.0Nm)
2570N
25
16
150
20
20
HKY20F 18 (2.0Nm)
* Order number of clamp screw A=HSS04004, B=HSS04006, C=HSS04008
E036
3-M4 x .7
D4
D5
Order Number
S2
D5
5mm S1
SBH
Square type holder
CB type (Boring bar ts to a holder)
20
10
Stock
L3
Dimensions (mm)
Maximum Tool Overhang L3
(Recommended tool overhang when machining general steels) S2 B
CG CBCG
CB CG CT
CB CG..RS-10 CG..RS-20
CT
CR
CTCR
type type type type CG..RS-10B CG..RS-20B type
type CTCR
type type
MICRO-MINI TWIN
F1
6 24
(6 10)
CB
type
CG
type
CT
type
CR
type
02RS(-B)
02RS-0p(B)
Clamp
Torque
Wrench ( )
Screw
lbf-in
HSC
42
HKY30R (4.8 )
Nm
04010
SBH1020R
13
1030R
14 13.8 13.8
8.5 22 13 17.5 14 16.5 13 17.5 11 19.5

03RS(-B) 030pRS-pp(B) 0305RS-M4 03RS-01 HSC
84
HKY40R (9.5 )
14 13.8
(9 15) (14)
(15)
(14)
(12)
Nm
03RS-0p(B) 03RS-pp(B) 03RS-M4(B) 03RS-01B 05012
1040R
15 14.8 14.8
11 29.5 18 22.5 19 21.5 18.5 22 13 27.5

84
HKY40R (9.5 )
15 14.7
(12 20)
(19)
(20)
(19.5)
(14)
Nm
1050R
16 15.8 15.8
13.5 37 23 27.5 24 26.5 24 26.5 15 35.5

84
HKY40R (9.5 )
16 15.6
(15 25)
(24)
(25)
(25)
(16)
Nm
1060R
17 16.8 16.8
13.5 42 23 32.5 24 31.5 24 31.5

(18 30)
(24)
(25)
(25)
17 16.5
06RS(-B) 061pRS-pp(B) 0610RS-M10

06RS-0p(B) 06RS-pp(B) 06RS-M10(B)
HSC
84
HKY40R (9.5 )
Nm
05012
1070R
18 17.8
13.5 52 28 38 29 37
(30)
(21 35) (29)
18 17.4
07RS(-B) 071pRS-pp(B)
07RS-0p(B) 07RS-pp(B)
HSC
84
HKY40R (9.5 )
Nm
05012
12.9
BORING BARS
F1
S2
S2
F1
L3
CT type (Boring bar ts to a holder)
CG type (Boring bar ts to a holder)
Order Number
10
100
10
L3
(Clamp)
F1
45
* The MICRO-DEX and the MICRO-MINI cannot be t to square holders.
SPARE PARTS
M001
TECHNICAL DATA
N001
E037
BORING BARS
HOLDER
HOLDER CROSS REFERENCE LIST OF METRIC SHANK STANDARD
Holder
MICRO-MINI TWIN
MICRO-MINI
MICRO-DEX
Type
Order Number
RBH1620N
1630N
Round
Type
Holder
& 16mm
1640N
1650N
1660N
BORING BARS
1670N
RBH2020N
2030N
Round
Type
Holder
& 20mm
2040N
2050N
2060N
2070N
RBH2220N
2230N
Round
Type
Holder
& 22mm
2240N
2250N
2260N
2270N
RBH2520N
2530N
Round
Type
Holder
& 25mm
2540N
2550N
2560N
2570N
SBH1020R
1030R
Square
Type
Holder
r10mm
1040R
1050R
1060R
1070R
CB
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
CR
Machine Makers
C
03RS-01
03RS-01B
04RS-01
04RS-01B
05RS-01
05RS-01B
03FR-BLS
MIYANO MACHINERY
JAPAN INC.
C05GSpppRpp 05FR-BLS NC lathes

C06GSpppRpp
C07GSpppRpp
03RS-01
03RS-01B
04RS-01
04RS-01B
05RS-01
05RS-01B

03FR-BLS Citizen Precision Machinery

Co., Ltd.
C04GSpppRpp 04FR-BLS Tsugami Corporation
C05GSpppRpp 05FR-BLS MIYANO MACHINERY
JAPAN INC.

C06GSpppRpp
NC lathes

C07GSpppRpp
03RS-01
03RS-01B
04RS-01
04RS-01B
05RS-01
05RS-01B
03FR-BLS
STAR MICRONICS
C05GSpppRpp 05FR-BLS CO., LTD.
C06GSpppRpp
C07GSpppRpp
03RS-01
03RS-01B
04RS-01
04RS-01B
05RS-01
05RS-01B
C04GSpppRpp
C06GSpppRpp
C07GSpppRpp
C05GSpppRpp
03FR-BLS Tsugami Corporation

04FR-BLS MIYANO MACHINERY
JAPAN INC.
05FR-BLS
NC lathes
03RS-01
03RS-01B
04RS-01
04RS-01B
05RS-01
05RS-01B
NC lathes
* Mitsubishi Materials obtained the makers' approval before entering their names in the list.
E038
SPARE PARTS
M001
TECHNICAL DATA
N001
PRECAUTION IN USING
THE MICRO-MINI TWIN
PRECAUTIONS IN USING THE MICRO-MINI TWIN
aWhen using a holder for general purpose/small automatic lathe
aTo avoid chipping of the 2nd cutting edge take care when inserting the boring bar into the holder. Refer
to g.1 if the 2nd edge contacts the internal face of the holder there is a possibility that it may chip.
Fig.1
Internal face of the holder
Cutting edge
Insert direction
3rd clamping screw
2nd cutting edge
aWhen using a square type holder

aWhen installing the boring bar into the holder, tighten the clamping screw making the micro-mini
twin boring bars in contact with the reference plane of square type holder.
sMake sure that the clamp screw is tightened. The recommended set torque value is shown
in the table of holder.
dDon't tighten the clamp screw without a micro-mini twin boring bar, otherwise the clamp bridge can
be deformed.
Fig.3
Insert
The reference plane

of square type holder
BORING BARS
sWhen clamping the boring bar into the holder, there is a possibility that damage to the shank and the Fig.2
2nd cutting edge can occur. Make sure that the clamping screws are tightened to the set torque value.
Additionally make sure that there is no clamping screw near the 2nd cutting edge as this can break the
boring bar.
eWhen using Mitsubishi holders with a tool overhang of 5 lxd, ensure that the 3rd clamping screw is
removed prior to machining. (For RBH1620N, RBH19020N there are no 3rd clamping screws).
Insert point
The set torque value for clamping screw is 18 lbf-in. (2.0 N m)
Tighten the clamping screw ensuring making the micro-mini twin

boring bars in contact with the reference plane of square type holder.
E039
GUIDE TO
GROOVING TOOLS
a Section
organization
z Classied according to external or internal applications.

x Sub-classied according to product series.
[For Internal Grooving & Threading]
[For External Grooving]

MIN. CUTTING DIAMETER
uses illustrations and arrows to depict available machining

applications such as cutting off, grooving and copying.
is color-coded to locate at a
glance, the minimum
cutting diameters for internal
machining.
INDICATION OF HOLDER TYPE ACCORDING TO APPLICATION

indicates the holder types, such as 00 type or 90 type.
TITLE OF PRODUCT
GEOMETRY
PRODUCT SECTION
GROOVING SYSTEM
INTERNAL GROOVING
GY SERIES (EXTERNAL GROOVING)
STHN/O TYPE
1-1
S-STHN/O
00 type holder (Inch)
Insert GY2Mooooooooo-GS Insert GY2Mooooooooo-GS

Insert GY2Mooooooooo-GM Insert GY2Mooooooooo-GM
Insert GY1Gooooooooo- GF
GS Insert GY2MoooooR/Loo-GM
Note 1) For modular blades and modular holders, please order separately.
Note 2) Please use right hand modular blade for right hand modular holder and
left hand modular blade for left hand modular holder.
a Screw-on type.
a Precision class insert.
a Holder is capable of performing both grooving and threading.
a Economical due to the use of 3 cutting edges.
Internal grooving, Threading, Boring
D4
L1
F1
RR
a a
32p
1.000
10.000
.656
10
1.250
.060 / .156
GTS1
TKY10F
a a
43p
1.250
12.000
.843
10
1.750
.156 / .234
GTS2
TKY20F
43p
1.500
14.000
.968
10
2.250
.156 / .234
GTS2
TKY20F
a a
43p
2.000
14.000
1.218
10
3.000
.156 / .234
GTS2
TKY20F
a a
54p
2.000
14.000
1.250
4.000
.297
GTS3
TKY20F
Order Number
Insert Number
R L
Max.
Max.
Hand Groove Depth Cut Off Diameter
ar
D1
(R/L)
(inch)
(inch)
.079
.236
.394
.709
.236
.394
.709
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.394
.709
.236
.394
.709
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.472
.787
*4
*4
*
*1
*1
*
*4
*4
*
*1
*1
.472
.787
1.417
.472
.787
1.417
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.787
1.417
.472
.787
1.417
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
*2
*2
*
*2
*2
*2
Order Number
ID
(1D1R3D1)
(1D1R3D2)
(1D1R3D3)
(1F1R3D1)
(1F1R3D2)
(1F1R3D3)
(1F1R4D1)
(1F1R4D2)
(1F1R4D3)
(1H1R4D1)
(1H1R4D2)
(1H1R4D3)
(1K1R4D1)
(1K1R4D2)
(1K1R4D3)
(1M1R4D1)
(1M1R4D2)
(1M1R4D3)
(1D1L3D1)
(1D1L3D2)
(1D1L3D3)
(1F1L3D1)
(1F1L3D2)
(1F1L3D3)
(1F1L4D1)
(1F1L4D2)
(1F1L4D3)
(1H1L4D1)
(1H1L4D2)
(1H1L4D3)
(1K1L4D1)
(1K1L4D2)
(1K1L4D3)
(1M1L4D1)
(1M1L4D2)
(1M1L4D3)
Modular Blade
Stock
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
a
a
Modular Holder
Stock
GYHRUS10B00-M20R
GYHRUS12C00-M20R
GYHRUS12C00-M25R
INSERTS (GROOVING)
Order Number
a
a
a
GYHRUS16D00-M25R
a
a
a
GYHRUS20D00-M25R
a
a
a
GYHRUS24E00-M25R
a
a
a
GYHLUS10B00-M20L
a
a
a
GYHLUS12C00-M20L
a
a
a
GYHLUS12C00-M25L
GYHLUS16D00-M25L
GYHLUS20D00-M25L
GYHLUS24E00-M25L
Order Number
a
a
a
a
Dimensions (inch)
W3
D1
S1
L3
Re
.375
.375
.125
.125
.057
.057
< .003
.032
.032
.063
.375
.125
.156
< .003
.063
.375
.125
.156
< .003
.063
.500
.188
.156
< .003
.063
.500
.188
.156
< .003
.094
.500
.188
.156
< .003
.094
.500
.188
.156
< .003
.125
.500
.188
.234
< .003
.125
.500
.188
.234
< .003
.156
.500
.188
.234
< .003
.156
.500
.188
.234
< .003
E
E
.625
.625
.250
.250
.297
.297
< .003
.187
.187
Min.
Pitch
(T.P.I)
D1
S1
Re
8
6
4
.375
.500
.625
.125
.187
.250
.004
.004
.004
NX55
UTi20T
Geometry
< .003
< .003
INSERTS (THREADING)
Stock
Cermet Carbide
UP20M
a
a
TNMC32NGR032
32NGL032
32NGR063
32NGL063
43NGR063
43NGL063
43NGR094
43NGL094
43NGR125
43NGL125
43NGR156
43NGL156
54NGR187
54NGL187
Coated
E
E
a
a
TNMC
Clamp Screw Wrench
(Note) Please use left hand insert for right hand holder and right hand insert for left hand holder.
a
a
a a
Class
Seat
Size
Insert
Width
W3
(inch)
S16-STHNR/L-3
S20-STHNR/L-4
S24-STHNR/L-4
S32-STHNR/L-4
S32-STHOR/L-5
TNMC32NV
43NV
54NV
Class
GROOVING
Max.
Groove
Depth
(inch)
ap
Min.
Cutting
Diameter
(inch)
D1
Dimensions (inch)
Stock
Fig. 2
GROOVING
Fig. 1
E
E
E
Coated
Stock
Cermet Carbide
UP20M
NX55
UTi20T
Dimensions (inch)
Geometry
a
*1
*2
The maximum groove depth varies according to the insert used. Please refer to the maximum groove depth of inserts on pages F012 and F013.
*21 The
maximum cut off diameter D1 varies according to the insert used. The cut off diameter is double the maximum groove depth (ar) of inserts on pages F012 and F013.
*3 Dimensions
are when the gauge insert is used. If other insert geometries are used then L1, L2 and F1 values may vary.
*4 The maximumshown
groove depth is limited by the workpiece diameter. For details, please refer to page F047.
*
F014
SPARE PARTS
M001
TECHNICAL DATA
N001
F161
STANDARDS FOR
APPLICABLE INSERTS
PRODUCT STANDARDS
indicates stock status, dimensions,

etc. for applicable inserts.
indicates order numbers, stock status

(per right/left hand), holders, modular blades
groove widths, maximum groove depths,
maximum cut-off diameters, dimensions,
applicable inserts, and cutting edge shapes.
aTo
F000
Order:
For holder, please specify order number and hand of tool (right/left).
For insert, please specify insert number and grade.
For blade, please specify order number.
LEGEND FOR
STOCK STATUS MARK
is shown on the left hand
page of each double-page
spread.
TURNING
GROOVING TOOLS
CLASSIFICATION (EXTERNAL CUTTING) ....................... F002
CLASSIFICATION (INTERNAL CUTTING) ........................ F003
STANDARD
GY HOLDER (GROOVING)
CLASSIFICATION OF GY HOLDER ............................ F004
HOW TO SELECT GY HOLDER .................................. F006
IDENTIFICATION OF GY HOLDER ............................. F010
GY INSERTS .....................................................................
GY HOLDER (EXTERNAL) ...............................................
GY HOLDER (FACE GROOVING) ....................................
GY HOLDER (INTERNAL) ................................................
F012
F014
F054
F134
UG HOLDER (EXTERNAL GROOVING) ........................ F158

MTVO HOLDER (EXTERNAL GROOVING) ................... F160
S-STHN/O HOLDER (INTERNAL GROOVING) ............. F161
FSL51/52 HOLDER (INTERNAL GROOVING)............... F162
S-SL5N HOLDER (INTERNAL GROOVING) .................. F163
MICRO-MINI TWIN BORING BARS
CG TYPE (INTERNAL GROOVING) ............................... F165
Arranged by Alphabetical order.

F165
F162
F014
F012
F158
F159
F164
F164
F164
F160
F163
F161
F161
F160
F158
CG
FSL5
GY (Holders)
GY (Inserts)
KGBN
KGT (Inserts)
MLG (Inserts)
MLP (Inserts)
MLT (Inserts)
MTVO
S-SL5N
Soo-STHN
Soo-STHO
TNMC (Inserts)
UGHN
F001
GROOVING
CLASSIFICATION
EXTERNAL CUTTING
UG Holder
rigidity due
to the modular blade.
(Tri-lock system)
a Various insert types.
.079 (2.0mm)
.094
.098 (2.5mm)
.118 (3.0mm)
.125
.157 (4.0mm)
.187
.197 (5.0mm)
.236 (6.0mm)
.250
a Spring clamp type.

a Strengthened insert clamping.
a Block and blade type.
a Maximum cut off diameter
.087
.122
.161
.201
GROOVING
4.724inch.
MTVO Holder
a Clamp-on type.
a Positive insert produces
nished surface.
F002
a good
.032
.063
.094
.125
.156
.187
Face
Grooving
a Clamp-on type.
a High accuracy and
Cutting Off
Features
Copying
GY Holder
Insert Shape
Deep
Grooving
Name of Tool Holder
Shallow
Grooving
Groove Width According

to Cutting Mode (inch)
.118
.125
.157
.187
.197
.236
.250
.118
.125
.157
.187
.197
.236
.250
Page
F014
F158
F160
INTERNAL CUTTING
Insert Shape
Features
Max.
Groove
Depth
(inch)
(inch)
(inch)
.984
(25mm)
.079 (2.0mm)
.094
.098 (2.5mm)
.118 (3.0mm)
.125
.157 (4.0mm)
.187
.197 (5.0mm)
.236 (6.0mm)
.250
1.250
.032
.063
.094
.125
.156
.187
a Clamp-on type.
a High accuracy and
GY
a Screw-on type.
a Holder is capable of performing
STHN/0
a Screw-on type.
a Holder is capable of performing
FSL5
S-SL5
.394
.060
F161
.297
.039
both grooving and threading.

a Maximum groove depth .118inch.
.047 (1.2mm)
.059 (1.5mm)
.062
.079 (2.0mm)
.094
.118 (3.0mm)
.125
.156
.157 (4.0mm)
F134
.512
both grooving and threading.

a Economical due to the use of
3 cutting edges.
.157
rigidity due
to the modular blade.
(Tri-lock system)
Page
GROOVING
Name of Tool Holder
Groove
Width
Min.
Cutting
Diameter
F162
.118
a Solid carbide type.

a Economical due to
MICRO-MINI TWIN
Boring Bars
single holder
with two cutting edges.
.08
.08
.08
.04
F165
type.
ground to suit the
application.
.126
.04
a Solid carbide
a Insert can be
MICRO-MINI
Boring Bars
.04
.118
.12
.08
E031
F003
GROOVING (EXTERNAL / INTERNAL)
FEATURES OF THE GY SERIES

GY series offers ultimate rigidity and accuracy for stable grooving applications.
Modular system allows for high exibility while maintaining overall strength comparable to a mono block type holder.
New Tri Lock System for increased stability

and performance!
GROOVING
a Innovative Tri Lock System

Mitsubishi Materials has
developed a new geometry
modular blade that is totally
original and incomparable.*
Tri lock system ensures that
the modular blade is securely
located from 3 directions
2Lock
(side,front and top).
This leads to high rigidity
clamping and stable
grooving.
3Lock
3Lock
3Lock
1 Lock
2Lock
1 Lock
1 Lock
2Lock
*Mitsubishi Materials study data

Internal GY Holder
External GY Holder
a Outstanding compatibility
One tool holder can be used to have a number
of modular blades offering exibility and
improved tool management.
a A wide variety of products available
from a minimum diameter 25.0mm.

Modular blade
type
Mono block
type
Modular blade
for external grooving
Modular blade
for face grooving
(short)
(Standard)
(short)
(Standard)
New insert design leading the way for new grooving applications !
a Highly reliable insert clamping
Safety keys prevent insert movement.
The convex geometry ensures high precision clamping.
Convex
contact
face
F004
Insert
a A wide selection of inserts

a Breaker system
GU breaker
GS breaker
(Low feeds)
For Gummy Steel
MS breaker
(Low feeds)
a Selection of groove widths

Grooving
GM breaker
GFGS
(Medium feeds)
(CBN)
Copying
Multifunctional Grooving
MM breaker
BM breaker
(Medium feeds)
a Different corner radii available
GU breaker
For Gummy Steel
GS breaker
(Low feeds)
Cutting Off
GM breaker
(Medium feeds)
R/L05-GM
breaker
GROOVING
(Medium feeds)
a Application of Insert Grades

Work Material
Machining Condition
Stable
Steel
Stainless Steel
Cast Iron
Heat-resistant Alloy / Titanium Alloy
Hardened Steel
MY5015
VP10RT
NX2525
MY5015
Machining
Condition
VP10RT
VP10RT
VP20RT
VP20RT
MB8025
VP10RT
VP20RT
VP20RT
Unstable
Note 1) VP20RT is the rst recommended grade for materials other than hardened steel.
Note 2) For VP10RT, VP20RT and MY5015, wet cutting is recommended.
VP20RT (First recommendetion)
MY5015
aCVD coated MY5015 with excellent wear
aMIRACLE coated VP20RT for general turning operations.
resistance at higher cutting temperatures.

It demonstrates longer tool life when
machining cast iron and ductile cast iron.
Also use for high speed cutting of steel under
stable conditions such as continuous cutting.
The combination of the tough special cemented carbide

substrate and MIRACLE coating bring a good balance of
wear resistance and fracture toughness at a high level.
Corresponding to various work piece materials and
diverse applications.
CVD coating
MIRACLE coating
Carbide substrate
Carbide substrate (HRA90.5)
VP10RT
aMIRACLE coated VP10RT has high wear resistance.
It adopts the special cemented carbide substrate that

is harder than VP20RT.
Use for hard-to-cut materials or to extend tool life.
MIRACLE coating
Carbide substrate (HRA92.0)
NX2525
aNX2525 is a cermet grade for nishing.
Use for nish cutting of steel to obtain a glazed surface or

low-cutting-speed applications that weld easily.
MB8025
aMB8025 is a sintered cubic-boron-nitride grade for
hardened steel.
F005
GROOVING SYSTEM
SELECTION GUIDE (1)

STEP1 SELECT APPLICATION
Select the application and the direction of the workpiece rotation.
Clockwise
y Normal use
External grooving / Cutting off / Copying
00 type (Inch)
00 type (Metric)
5-1 90 right hand type (Inch) F134

5-2 90 right hand type (Metric) F140
F014
F030
y Reverse holder use
1-1
1-2
00 type (Inch)
00 type (Metric)
F014
F030
2-1 90 left hand type (Inch) F026

2-2 90 left hand type (Metric) F042
GROOVING
1-1
1-2
Internal grooving / Copying
Face grooving / Copying






STEP2 SELECT INSERT

Select an insert suitable for the application, then select the corresponding seat size.
* Seat size refers to the seat width of the modular blade.
ar (Max.)
GM Breaker
(Medium feeds)
F006
MB8025
MY5015
NX2525
VP20RT
a
For Grooving / Cutting off
GS Breaker
(Low feeds)
VP10RT
a
a
H
H
J
0635J040N-GU
GY2M0200D020N-GS
.079 .0012 .008
.736
.815
0239E020N-GS
.094 .0012 .008
.728
.815
0250E020N-GS
.098 .0012 .008
.728
.815
0300F020N-GS
.118 .0012 .008
.728
.815
0318F020N-GS
.125 .0012 .008
.728
.815
0400G020N-GS
.157 .0016 .008
.941
1.010
0475H030N-GS
.187 .0016 .012
.941
1.010
0500H030N-GS
.197 .0016 .012
.945
1.010
0600J030N-GS
.236 .0016 .012
.949
1.010
0635J030N-GS
.250 .0016 .012
.949
1.010
GY2M0200D020N-GM
.079 .0012 .008
.764
.815
0239E020N-GM
.094 .0012 .008
.764
.815
0250E020N-GM
.098 .0012 .008
.764
.815
0600J040N-GU
a
a
0475H040N-GU
GY2M0400G030N-GU
0500H040N-GU
Re.002"
L2
Re.002"
GU Breaker
(For Gummy Steel)
Order Number
Dimensions (inch)
W3
Seat
ar
Size Grooving
Re
(Max.)
Tolerance
Width
Geometry
(inch)
Stock
Coated Cermet CBN
Applications
Inserts
.157 .0016 .012
.953
1.010
.187 .0016 .016
.953
1.010
.197 .0016 .016
.953
1.010
.236 .0016 .016
.953
1.010
.250 .0016 .016
.953
1.010
Counter Clockwise
y Normal use
00 type (Inch)
00 type (Metric)
F014
F030

1-1
1-2
00 type (Inch)
00 type (Metric)
F014
F030

GROOVING
1-1
1-2
y Reverse holder use






STEP3 SELECT MODULAR HOLDER & BLADE

Select a modular holder suitable
for the application.
Select the maximum groove depth.
Select a modular blade that corresponds to .
When selecting a modular blade for face grooving
note if the cutting diameter range is suitable.
Proceed to the tool holder page in

STEP1, then go to the column of the
seat size selected in STEP 2.
Select the hand of the tool holder.
Insert GY2Mooooooooo-BM Insert GY2Mooooooooo-GS

Insert GY2Mooooooooo-GM
Insert GY2MoooooR/Loo-GM
Fig. 2
Fig. 1
Seat
Size
Insert
Width
W3
(inch)
Max.
Max.
ar
D1
(R/L)
(inch)
(inch)
.079
.236
.394
.709
.236
.472
.787
.236
.394
.709
.236
.472
.787
.236
394
*4
*
*1
Order Number
ID
Modular Blade
Stock
.472
.787
1.417
.472
.945
1.575 2
(2F1R3D1)
(2F1R3D2)
(2F1R3D3)
(2H1R4D1)
(2H1R4D2)
(2H1R4D3)
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
.472
.787
1.417
.472
.945
1.575 2
(2F1L3D1)
(2F1L3D2)
(2F1L3D3)
(2H1L4D1)
(2H1L4D2)
(2H1L4D3)
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
(2F1R3E1)
(2F1R3E2)
GYM20LA-E06
GYM20LA E10
.472
787
Modular Holder
Stock
GYHRUS12C90-M20L
GYHRUS16D90-M25L
GYHLUS12C90-M20R
GYHLUS16D90-M25R
GYHRUS12C90 M20L
a
a
a
a
a
a
a
a
a
F007
GROOVING SYSTEM
SELECTION GUIDE (2)

HOLDER SELECTION
External Grooving (^ F014-F053)
2 90 type
00 type
GROOVING
a Modular blade type
Inserts
^ P11
Insert Width
.094
.118
.187
.236
Inch
.079
.157
.098
.125
.197
.250
2.39mm
3.00mm
4.75mm
6.00mm
Metric 2.00mm 2.50mm 3.18mm 4.00mm 5.00mm 6.35mm
Insert Width
.094
.118
.187
.236
.079
.157
.098
.125
.197
.250
2.39mm
3.00mm
4.75mm
6.00mm
2.00mm 2.50mm 3.18mm 4.00mm 5.00mm 6.35mm
Inch Holders
R
L
^ F014 ^ F016 ^ F018 ^ F020 ^ F022 ^ F024

^ F014 ^ F016 ^ F018 ^ F020 ^ F022 ^ F024
^ F026 ^ F026 ^ F026 ^ F028 ^ F028 ^ F028

^ F026 ^ F026 ^ F026 ^ F028 ^ F028 ^ F028
Metric Holders
R
L
^ F030 ^ F032 ^ F034 ^ F036 ^ F038 ^ F040

^ F030 ^ F032 ^ F034 ^ F036 ^ F038 ^ F040
^ F042 ^ F042 ^ F042 ^ F044 ^ F044 ^ F044

^ F042 ^ F042 ^ F042 ^ F044 ^ F044 ^ F044
INSERT SELECTION
GU Breaker
For Gummy Steel
Grooving
GS Breaker
GM Breaker
(Low feeds)
(Medium feeds)
Flat Top
(CBN)
MS Breaker
(Low feeds)
Cutting Mode
External
F008
Face
Multifunctional Grooving
MM Breaker
(Medium feeds)
Cutting Mode
Internal
External
Face
Internal
00 type
Internal Grooving (^ F134-F151)
4 90 type
5 90 type
a Mono block type

(Through air / coolant)

(Through air / coolant)
Insert Width
.118
.187
.236
.157
.125
.197
.250
3.00mm 4.00mm 4.75mm 6.00mm
3.18mm
5.00mm 6.35mm
Insert Width
.118
.187
.236
.157
.125
.197
.250
3.00mm 4.00mm 4.75mm 6.00mm
3.18mm
5.00mm 6.35mm
Insert Width
.094
.118
.187
.236
.079
.157
.098
.125
.197
.250
2.39mm
3.00mm
4.75mm
6.00mm
2.00mm 2.50mm 3.18mm 4.00mm 5.00mm 6.35mm
^ F054
^ F058
^ F062
^ F066
^ F070
^ F074
^ F078
^ F080
^ F082
^ F082
^ F084
^ F084
^ F086
^ F086
^ F088
^ F088
^ F134 ^ F134 ^ F136 ^ F136 ^ F138 ^ F138

^ F134 ^ F134 ^ F136 ^ F136 ^ F138 ^ F138
^ F090
^ F094
^ F098
^ F102
^ F106
^ F110
^ F114
^ F116
^ F118
^ F118
^ F120
^ F120
^ F122
^ F122
^ F124
^ F124
^ F140 ^ F140 ^ F142 ^ F142 ^ F144 ^ F144

^ F140 ^ F140 ^ F142 ^ F142 ^ F144 ^ F144
Copying
BM Breaker
GU Breaker
For Gummy Steel
Face
(Low feeds)
(Medium feeds)
R/L05-GM Breaker
(Medium feeds)
Cutting Mode
Cutting Mode
External
Cutting Off
GS Breaker
GM Breaker
GROOVING
Face Grooving (^ F054-F133)
Internal
External
Face
Internal
F009
GROOVING SYSTEM
IDENTIFICATION
Insert
z Series Description
bSeat Size 1
v Groove Width
Inch
Metric
x Number of Teeth
0200
.079"
2.00mm
1 Edge Type
0239
.094"
2.39mm
2 Edge Type
0250
.098"
2.50mm
0300
.118"
3.00mm
c Peripheral
0318
.125"
3.18mm
0400
.157"
4.00mm
Ground
G
H
J
Metric
.079"
.094"
.098"
.118"
.125"
.157"
.187"
.197"
.236"
.250"
2.00mm
2.39mm
2.50mm
3.00mm
3.18mm
4.00mm
4.75mm
5.00mm
6.00mm
6.35mm
. Application 1
n Corner Radius
/ Application 2
Inch
Metric
Grooving/Cutting off
Low feed
020
.008"
0.20mm
M Multifunctional
Medium feed
030
.012"
0.30mm
Gummy steel
040
.016"
0.40mm
080
.031"
0.80mm
150
.059"
1.50mm
159
.063"
1.59mm
Copying (Ball nose)
Application 3
F
Flat Top
Only for CBN inserts.
, Lead angle (R/L type insert)
Sintered
0475
.187"
4.75mm
200
.079"
2.00mm
Blank
0500
.197"
5.00mm
238
.094"
2.38mm
0600
.236"
6.00mm
250
.098"
2.50mm
0635
.250"
6.35mm
300
.118"
3.00mm
Neutral
318
.125"
3.18mm
Right
Left
GROOVING
*1
Inch
05
Horning Type
m Hand
GS General Purpose
* Only for CBN inserts.
Select a seat size with the same symbol as that of modular blade and mono block holder.
Modular blade
zSeries Description
x Modular Blade Size
M20
M25
cHand
R
Right
Left
b Seat Size 1
vModular Blade Type

A
External / Internal
Standard Type
External only
Reinforced Type
Face grooving Type
D
E
F
G
H
J
Inch
Metric
.079"
.094"
.098"
.118"
.125"
.157"
.187"
.197"
.236"
.250"
2.00mm
2.39mm
2.50mm
3.00mm
3.18mm
4.00mm
4.75mm
5.00mm
6.00mm
6.35mm
n Max. Groove Depth
*2
m Min. Groove Diameter
Inch
Metric
06
.236"
6mm
035 1.378"
35mm
08
.315"
8mm
040 1.575"
40mm
10
.394"
10mm
050 1.969"
50mm
12
.472"
12mm
060 2.362"
60mm
14
.551"
14mm
070 2.756"
70mm
18
.709"
18mm
075 2.953"
75mm
20
.787"
20mm
085 3.346"
85mm
25
.984"
25mm
100 3.937" 100mm
Inch
110
Metric
4.331" 110mm
125 4.921" 125mm

135 5.315" 135mm
170 6.693" 170mm
*
*
*
F010
1 Select a seat size with the same symbol as that of insert.

2 The maximum groove depth is a value when used for external grooving and changes according to the insert used.
For internal grooving, refer to the maximum groove depth on pages F134-F144.
3 GYM20R/LA-o10, GYM20R/LA-o12, GYM25R/LA-o12 and GYM25R/LA-o14 can be used for both external
and internal grooving.
180 7.087" 180mm

250 9.843" 250mm
* Only for face grooving.
EXTERNAL / FACE HOLDER

(Inch)
(Metric)
v Holder Size
c Hand of Holder
b Holder Length
Metric
Inch
n Angle (degree)
Metric
Right
US10 .625"x.625" 1616 16mmx16mm
4.5"
110mm
Left
US12 .750"x.750" 2020 20mmx20mm
5.0"
125mm
US16 1.000"x1.000" 2525 25mmx25mm
6.0"
150mm
US20 1.250"x1.250" 3225 32mmx25mm
7.0"
170mm
x Holder Type
External / Face Holder
Inch
, Hand of Modular Blade
00
Right
90
90
Left
m Modular Blade Size

M20
US24 1.500"x1.500" 3232 32mmx32mm
M25
INTERNAL HOLDER
Block Holder Type
GROOVING
a Mono
(Inch)
(Metric)
b Holder Length
v Shank Size
Inch
Metric
c Hand of Holder
R
Right
Left
n Angle (degree)
. Max. Grooving Depth
90
Inch
Metric
.750"
20
20mm
5.0"
125mm
06
.236"
6mm
US16 1.000"
25
25mm
7.0"
180mm
07
.276"
7mm
8.0"
200mm
US12
Inch
Metric
90
x Holder Type
Mono block type
A
m Neck Length
Inch
Metric
1.250"
30mm
1.500"
40mm
, Seat Size 1
D
E
F
G
H
J
a Modular
Inch
Metric
.079"
.094"
.098"
.118"
.125"
.157"
.187"
.197"
.236"
.250"
2.00mm
2.39mm
2.50mm
3.00mm
3.18mm
4.00mm
4.75mm
5.00mm
6.00mm
6.35mm
Holder Type
(Inch)
(Metric)
v Shank Size
Inch
c Hand of Holder
b Holder Length
Metric
Metric
US20
1.250"
32
32mm
5.5"
140mm
Right
US24
1.500"
40
40mm
6.0"
150mm
Left
US32
2.000"
50
50mm
6.75"
170mm
S
x Holder Type
B
Inch
Modular blade type
10.0"
12.0"
250mm
300mm
n Angle (degree)
90
90
m Neck Length
. Hand of Modular Blade

R
Right
Left
Inch
Metric
2.000"
50mm
2.500"
60mm
, Modular Blade Size

M20
3.250"
80mm
M25
F011
GROOVING SYSTEM
CLASSIFICATION OF GY INSERTS (EXTERNAL / FACE / INTERNAL)
ar (Max.)
GM Breaker
(Medium feeds)
ar (Max.)
For Cutting off
R/L05-GM Breaker
ar (Max.)
F012
a
d
MB8025
NX2525
MY5015
VP20RT
a
a
0635J040N-GU
GY2M0200D020N-GS
.079 .0012 .008
.736
.815
0239E020N-GS
.094 .0012 .008
.728
.815
0250E020N-GS
.098 .0012 .008
.728
.815
0300F020N-GS
.118 .0012 .008
.728
.815
0318F020N-GS
.125 .0012 .008
.728
.815
0600J040N-GU
L2
VP10RT
ar
(Max.)
For Grooving / Cutting off
GROOVING
GS Breaker
(Low feeds)
Re
0500H040N-GU
Re.002"
Seat
Size Grooving
Tolerance
Width
0475H040N-GU
Re.002"
Dimensions (inch)
W3
GY2M0400G030N-GU
GU Breaker
(For Gummy Steel)
Order Number
Geometry
(inch)
Stock
Coated Cermet CBN
Applications
Inserts
.157 .0016 .012
.953
1.010
.187 .0016 .016
.953
1.010
.197 .0016 .016
.953
1.010
.236 .0016 .016
.953
1.010
.250 .0016 .016
.953
1.010
0400G020N-GS
.157 .0016 .008
.941
1.010
0475H030N-GS
.187 .0016 .012
.941
1.010
0500H030N-GS
.197 .0016 .012
.945
1.010
0600J030N-GS
.236 .0016 .012
.949
1.010
0635J030N-GS
.250 .0016 .012
.949
1.010
GY2M0200D020N-GM
.079 .0012 .008
.764
.815
0239E020N-GM
.094 .0012 .008
.764
.815
0250E020N-GM
.098 .0012 .008
.764
.815
0300F030N-GM
.118 .0012 .012
.764
.815
0318F030N-GM
.125 .0012 .012
.764
.815
0400G030N-GM
.157 .0016 .012
.961
1.010
0475H040N-GM
.187 .0016 .016
.957
1.010
0500H040N-GM
.197 .0016 .016
.957
1.010
0600J040N-GM
.236 .0016 .016
.957
1.010
0635J040N-GM
.250 .0016 .016
.957
1.010
GY2M0200D020R05-GM
.079 .0012 .008
.768
.819
0200D020L05-GM
.079 .0012 .008
.768
.819
0250E020R05-GM
.098 .0012 .008
.768
.820
0250E020L05-GM
.098 .0012 .008
.768
.820
0300F030R05-GM
.118 .0012 .012
.768
.821
0300F030L05-GM
.118 .0012 .012
.768
.821
0400G030R05-GM
.157 .0016 .012
.965
1.018
0400G030L05-GM
.157 .0016 .012
.965
1.018
0500H040R05-GM
.197 .0016 .016
.965
1.022
0500H040L05-GM
.197 .0016 .016
.965
1.022
: Inventory maintained. u : Inventory maintained. (Available Spring 2011)

: Inventory maintained in Japan. (Available Spring 2011)
<10 inserts in one case><CBN: 1 insert in one case>
ar (Max.)
For Copying
BM Breaker
ar (Max.)
For Grooving
Flat Top (CBN)
2 Edge Type
W3
Re
Re
L2
1 Edge Type
W3
Re
Re
L2
GY2M0300F020N-MS
0300F040N-MS
0400G020N-MS
0400G040N-MS
0500H040N-MS
0500H080N-MS
0600J040N-MS
0600J080N-MS
GY2M0200D020N-MM
0250E020N-MM
0300F020N-MM
0300F040N-MM
0300F080N-MM
0400G020N-MM
0400G040N-MM
0400G080N-MM
0500H040N-MM
0500H080N-MM
0600J040N-MM
0600J080N-MM
GY2M0200D100N-BM
0250E125N-BM
0300F150N-BM
0318F159N-BM
0400G200N-BM
0475H238N-BM
0500H250N-BM
0600J300N-BM
0635J318N-BM
GY1G0200D020N-GFGS
0239E020N-GFGS
0250E020N-GFGS
0300F020N-GFGS
0318F020N-GFGS
0400G020N-GFGS
0475H020N-GFGS
0500H020N-GFGS
GY2B0220D020N
0270E020N
0340F020N
0420G020N
0520H020N
0655J020N
GY1B0220D020N
0270E020N
0340F020N
0420G020N
0520H020N
0655J020N
a a a a
*
*
*
*
*
*
*
*
*
*
*
*
* Blank inserts to be ground by customers.
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
u u u u
u u u u
a a a a
a a a a
u u u u
u u u u
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
u u u
u u u
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a
a
a
a
a
a
a
a
d d
d d
d d
d d
d d
d d
d d
d d
d d
d d
d d
d d
Dimensions (inch)
W3
Seat
Size Grooving
Tolerance
Width
F
F
G
G
H
H
J
J
D
E
F
F
F
G
G
G
H
H
J
J
D
E
F
F
G
H
H
J
J
D
E
E
F
F
G
H
H
D
E
F
G
H
J
D
E
F
G
H
J
ar
(Max.)
L2
.118 .0012 .008
.756
.815
.118 .0012 .016
.744
.815
.157 .0016 .008
.953
1.010
.157 .0016 .016
.941
1.010
.197 .0016 .016
.941
1.010
.197 .0016 .031
.925
1.010
.236 .0016 .016
.941
1.010
.236 .0016 .031
.925
1.010
.079 .0012 .008
.752
.815
.098 .0012 .008
.752
.815
.118 .0012 .008
.752
.815
.118 .0012 .016
.744
.815
.118 .0012 .031
.728
.815
.157 .0016 .008
.949
1.010
.157 .0016 .016
.941
1.010
.157 .0016 .031
.925
1.010
.197 .0016 .016
.941
1.010
.197 .0016 .031
.925
1.010
.236 .0016 .016
.941
1.010
.236 .0016 .031
.925
1.010
.079 .0012 .039
.768
.815
.098 .0012 .049
.760
.815
.823
Re
.118 .0012 .059
.748
.125 .0012 .063
.744
.823
.157 .0016 .079
.921
1.016
.187 .0016 .094
.902
1.016
.197 .0016 .098
.898
1.016
.236 .0016 .118
.886
1.020
.250 .0016 .125
.878
1.020
.079 .0012 .008
.815
.094 .0012 .008
.815
.098 .0012 .008
.815
.118 .0012 .008
.815
.125 .0012 .008
.815
.157 .0012 .008
1.010
.187 .0012 .008
1.010
.197 .0012 .008
1.010
.087 .0039 .008
.829
.106 .0039 .008
.829
.134 .0039 .008
.829
.165 .0039 .008
1.024
.205 .0039 .008
1.024
.258 .0039 .008
1.024
.087 .0039 .008
.827
.106 .0039 .008
.827
.134 .0039 .008
.827
.165 .0039 .008
1.020
.205 .0039 .008
1.020
.258 .0039 .008
1.020
Application of Insert Grades
F005
GROOVING
MM Breaker
(Medium feeds)
VP10RT
VP20RT
MY5015
NX2525
For Multifunctional Grooving
ar (Max.)
Order Number
RT9010
RT9020
MB8025
Applications
Geometry
(inch)
MS Breaker
(Low feeds)
Blank
Stock
Coated Cermet Carbide CBN
F013
GROOVING SYSTEM

1-1

Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Max.
Max.
ar
D1
(R/L)
(inch)
(inch)
.079
.236
.394
.709
.236
.394
.709
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.394
.709
.236
.394
.709
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.472
.787
.472
.787
1.417
.472
.787
1.417
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.787
1.417
.472
.787
1.417
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
Order Number
ID
(1D1R3D1)
(1D1R3D2)
(1D1R3D3)
(1F1R3D1)
(1F1R3D2)
(1F1R3D3)
(1F1R4D1)
(1F1R4D2)
(1F1R4D3)
(1H1R4D1)
(1H1R4D2)
(1H1R4D3)
(1K1R4D1)
(1K1R4D2)
(1K1R4D3)
(1M1R4D1)
(1M1R4D2)
(1M1R4D3)
(1D1L3D1)
(1D1L3D2)
(1D1L3D3)
(1F1L3D1)
(1F1L3D2)
(1F1L3D3)
(1F1L4D1)
(1F1L4D2)
(1F1L4D3)
(1H1L4D1)
(1H1L4D2)
(1H1L4D3)
(1K1L4D1)
(1K1L4D2)
(1K1L4D3)
(1M1L4D1)
(1M1L4D2)
(1M1L4D3)
Modular Blade
Stock
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
a
a
Modular Holder
Stock
GYHRUS10B00-M20R
GYHRUS12C00-M20R
GYHRUS12C00-M25R
GYHRUS16D00-M25R
GYHRUS20D00-M25R
GYHRUS24E00-M25R
GYHLUS10B00-M20L
GYHLUS12C00-M20L
GYHLUS12C00-M25L
GYHLUS16D00-M25L
GYHLUS20D00-M25L
GYHLUS24E00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
1 The maximum groove depth varies according to the insert used. Please refer to the maximum groove depth of inserts on pages F012 and F013.
2 The maximum cut off diameter D1 varies according to the insert used. The cut off diameter is double the maximum groove depth (ar) of inserts on pages F012 and F013.
3 Dimensions shown are when the gauge insert is used. If other insert geometries are used then L1, L2 and F1 values may vary.
4 The maximum groove depth is limited by the workpiece diameter. For details, please refer to page F047.
*
*
*
*
F014
* Wrench : zFor Clamp Screw xFor Blade Screw.

SPARE PARTS
z
Modular Holder Number
GYHR/LUS10B00-M20R/L
Wrench
TS407
zTKY30R
(Clamp Torque xTKY15D
: 31 lbf-in)
GYHR/LUS12C00-M20R/L
Fig. 4
Fig. 3
(5 pcs.)
Clamp Screw Blade Screw
GY06013M
(Clamp Torque
GYHR/LUS16D00-M25R/L
: 53 lbf-in)
TS55
zTKY30R
(Clamp Torque
xTKY25D
: 44 lbf-in)
GYHR/LUS24E00-M25R/L
*3
Cutting Mode
Insert
Fig.
H1
L1
L2
H2
F1
S3
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
4.264
4.500
4.736
4.764
5.000
5.236
4.685
5.000
5.236
5.685
6.000
6.236
5.685
6.000
6.236
6.685
7.000
7.236
4.264
4.500
4.736
4.764
5.000
5.236
4.685
5.000
5.236
5.685
6.000
6.236
5.685
6.000
6.236
6.685
7.000
7.236
1.102
1.339
1.575
1.102
1.339
1.575
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
1.102
1.339
1.575
1.102
1.339
1.575
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.812
.812
.812
.875
.875
.875
1.000
1.000
1.000
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
.812
.812
.812
.875
.875
.875
1.000
1.000
1.000
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
.125
.125
.125

.250
.250
.250

.125
.125
.125

.250
.250
.250

Clockwise
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
Counter Clockwise
Geometry / Insert Number
Page
GROOVING
Dimensions (inch)
GY2M0200D020N-GS
GY2M0200D020N-GM
(Gauge insert)
GY2M0200D020R05-GM
GY2M0200D020L05-GM F012
F013
GY2M0200D020N-MM
GY2M0200D100N-BM
GY1G0200D020N-GFGS
F015
GROOVING SYSTEM

1-1

Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Max.
Max.
ar
D1
(R/L)
(inch)
(inch)
.094
.098
.236
.394
.709
.236
.394
.709
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.394
.709
.236
.394
.709
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.472
.787
.472
.787
1.417
.472
.787
1.417
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.787
1.417
.472
.787
1.417
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
Order Number
ID
(1D1R3E1)
(1D1R3E2)
(1D1R3E3)
(1F1R3E1)
(1F1R3E2)
(1F1R3E3)
(1F1R4E1)
(1F1R4E2)
(1F1R4E3)
(1H1R4E1)
(1H1R4E2)
(1H1R4E3)
(1K1R4E1)
(1K1R4E2)
(1K1R4E3)
(1M1R4E1)
(1M1R4E2)
(1M1R4E3)
(1D1L3E1)
(1D1L3E2)
(1D1L3E3)
(1F1L3E1)
(1F1L3E2)
(1F1L3E3)
(1F1L4E1)
(1F1L4E2)
(1F1L4E3)
(1H1L4E1)
(1H1L4E2)
(1H1L4E3)
(1K1L4E1)
(1K1L4E2)
(1K1L4E3)
(1M1L4E1)
(1M1L4E2)
(1M1L4E3)
Modular Blade
Stock
GYM20RA-E06
GYM20RA-E10
GYM20RB-E18
GYM20RA-E06
GYM20RA-E10
GYM20RB-E18
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM20LA-E06
GYM20LA-E10
GYM20LB-E18
GYM20LA-E06
GYM20LA-E10
GYM20LB-E18
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
a
a
Modular Holder
Stock
GYHRUS10B00-M20R
GYHRUS12C00-M20R
GYHRUS12C00-M25R
GYHRUS16D00-M25R
GYHRUS20D00-M25R
GYHRUS24E00-M25R
GYHLUS10B00-M20L
GYHLUS12C00-M20L
GYHLUS12C00-M25L
GYHLUS16D00-M25L
GYHLUS20D00-M25L
GYHLUS24E00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*
*
*
*
F016

SPARE PARTS
z
Wrench
TS407
zTKY30R
(Clamp Torque
xTKY15D
: 31 lbf-in)
Fig. 4
Fig. 3
(5 pcs.)
GY06013M
(Clamp Torque
: 53 lbf-in)
TS55
zTKY30R
(Clamp Torque
xTKY25D
: 44 lbf-in)
*3
Cutting Mode
Insert
Fig.
H1
L1
L2
H2
F1
S3
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
4.264
4.500
4.736
4.764
5.000
5.236
4.685
5.000
5.236
5.685
6.000
6.236
5.685
6.000
6.236
6.685
7.000
7.236
4.264
4.500
4.736
4.764
5.000
5.236
4.685
5.000
5.236
5.685
6.000
6.236
5.685
6.000
6.236
6.685
7.000
7.236
1.102
1.339
1.575
1.102
1.339
1.575
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
1.102
1.339
1.575
1.102
1.339
1.575
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.812
.812
.812
.875
.875
.875
1.000
1.000
1.000
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
.812
.812
.812
.875
.875
.875
1.000
1.000
1.000
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
.125
.125
.125

.250
.250
.250

.125
.125
.125

.250
.250
.250

Clockwise
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
Counter Clockwise
Page
GROOVING
Dimensions (inch)
GY2M0239E020N-GS
GY2M0250E020N-GS
GY2M0239E020N-GM
GY2M0250E020N-GM
(Gauge insert)
GY2M0250E020R05-GM F012
GY2M0250E020L05-GM F013
GY2M0250E020N-MM
GY2M0250E125N-BM
GY1G0239E020N-GFGS
GY1G0250E020N-GFGS
F017
GROOVING SYSTEM

1-1
Insert GY2Mooooooooo-GS Insert GY2Mooooooooo-MM
Insert GY2Mooooooooo-GM Insert GY2Mooooooooo-MS
GS

Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Max.
Max.
ar
D1
(R/L)
(inch)
(inch)
.118
.125
.236
.394
.709
.236
.394
.709
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.394
.709
.236
.394
.709
.236
.472
.787
.236
.472
.787
.236
.472
.787
.236
.472
.787
.472
.787
1.417
.472
.787
1.417
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.787
1.417
.472
.787
1.417
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
.472
.945
1.575
Order Number
ID
(1D1R3F1)
(1D1R3F2)
(1D1R3F3)
(1F1R3F1)
(1F1R3F2)
(1F1R3F3)
(1F1R4F1)
(1F1R4F2)
(1F1R4F3)
(1H1R4F1)
(1H1R4F2)
(1H1R4F3)
(1K1R4F1)
(1K1R4F2)
(1K1R4F3)
(1M1R4F1)
(1M1R4F2)
(1M1R4F3)
(1D1L3F1)
(1D1L3F2)
(1D1L3F3)
(1F1L3F1)
(1F1L3F2)
(1F1L3F3)
(1F1L4F1)
(1F1L4F2)
(1F1L4F3)
(1H1L4F1)
(1H1L4F2)
(1H1L4F3)
(1K1L4F1)
(1K1L4F2)
(1K1L4F3)
(1M1L4F1)
(1M1L4F2)
(1M1L4F3)
Modular Blade
Stock
GYM20RA-F06
GYM20RA-F10
GYM20RB-F18
GYM20RA-F06
GYM20RA-F10
GYM20RB-F18
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM20LA-F06
GYM20LA-F10
GYM20LB-F18
GYM20LA-F06
GYM20LA-F10
GYM20LB-F18
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
a
a
Modular Holder
Stock
GYHRUS10B00-M20R
GYHRUS12C00-M20R
GYHRUS12C00-M25R
GYHRUS16D00-M25R
GYHRUS20D00-M25R
GYHRUS24E00-M25R
GYHLUS10B00-M20L
GYHLUS12C00-M20L
GYHLUS12C00-M25L
GYHLUS16D00-M25L
GYHLUS20D00-M25L
GYHLUS24E00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*
*
*
*
F018

SPARE PARTS
z
Fig. 4
Wrench
TS407
zTKY30R
(Clamp Torque
xTKY15D
)
: 31 lbf-in
Fig. 3
(5 pcs.)
GY06013M
(Clamp Torque
: 53 lbf-in)
TS55
zTKY30R
(Clamp Torque
xTKY25D
: 44 lbf-in)
*3
Cutting Mode
Insert
Fig.
H1
L1
L2
H2
F1
S3
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
4.264
4.500
4.736
4.764
5.000
5.236
4.685
5.000
5.236
5.685
6.000
6.236
5.685
6.000
6.236
6.685
7.000
7.236
4.264
4.500
4.736
4.764
5.000
5.236
4.685
5.000
5.236
5.685
6.000
6.236
5.685
6.000
6.236
6.685
7.000
7.236
1.102
1.339
1.575
1.102
1.339
1.575
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
1.102
1.339
1.575
1.102
1.339
1.575
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
1.220
1.535
1.772
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.625
.625
.625
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.812
.812
.812
.875
.875
.875
1.000
1.000
1.000
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
.812
.812
.812
.875
.875
.875
1.000
1.000
1.000
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
.125
.125
.125

.250
.250
.250

.125
.125
.125

.250
.250
.250

Clockwise
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
Counter Clockwise
Page
GROOVING
Dimensions (inch)
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
(Gauge insert)
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
F012
F013
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS
F019
GROOVING SYSTEM

1-1
GS

Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Max.
Max.
ar
D1
(R/L)
(inch)
(inch)
.157
Order Number
ID
Modular Blade
Stock
Modular Holder
Stock
.472
.945
(1D1R3G1)
GYM20RA-G12
GYHRUS10B00-M20R
.472
.945
(1F1R3G1)
GYM20RA-G12
GYHRUS12C00-M20R
.315
.551
.984
.315
.551
.984
.315
.551
.984
.315
.551
.984
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
(1F1R4G1)
(1F1R4G2)
(1F1R4G3)
(1H1R4G1)
(1H1R4G2)
(1H1R4G3)
(1K1R4G1)
(1K1R4G2)
(1K1R4G3)
(1M1R4G1)
(1M1R4G2)
(1M1R4G3)
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYHRUS12C00-M25R
GYHRUS16D00-M25R
GYHRUS20D00-M25R
GYHRUS24E00-M25R
*
*
*
*
a
a
a
a
a
a
a
a
a
a
a
.472
.945
(1D1L3G1)
GYM20LA-G12
GYHLUS10B00-M20L
.472
.945
(1F1L3G1)
GYM20LA-G12
GYHLUS12C00-M20L
.315
.551
.984
.315
.551
.984
.315
.551
.984
.315
.551
.984
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
(1F1L4G1)
(1F1L4G2)
(1F1L4G3)
(1H1L4G1)
(1H1L4G2)
(1H1L4G3)
(1K1L4G1)
(1K1L4G2)
(1K1L4G3)
(1M1L4G1)
(1M1L4G2)
(1M1L4G3)
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYHLUS12C00-M25L
GYHLUS16D00-M25L
GYHLUS20D00-M25L
GYHLUS24E00-M25L
a
a
a
a
a
a
a
a
a
a
a
*
*
*
F020

SPARE PARTS
z
Fig. 4
Wrench
TS407
zTKY30R
(Clamp Torque
xTKY15D
)
: 31 lbf-in
Fig. 3
(5 pcs.)
GYHR/LUS12C00-M25R/L GY06013M
(Clamp Torque
: 53 lbf-in)
TS55
zTKY30R
(Clamp Torque
xTKY25D
: 44 lbf-in)
H1
L1
L2
*3*3
H2
F1
Cutting Mode
S3
Clockwise
.625
.625 4.500 1.339
.625
.812 .125
.750
.750 5.000 1.339
.750
.875
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
4.764
5.000
5.433
5.764
6.000
6.433
5.764
6.000
6.433
6.764
7.000
7.433
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
1.000 .250
1.000 .250
1.000 .250
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
3
3
4
1
1
2
1
1
2
1
1
2
.625
.625 4.500 1.339
.625
.812 .125
.750
.750 5.000 1.339
.750
.875
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
4.764
5.000
5.433
5.764
6.000
6.433
5.764
6.000
6.433
6.764
7.000
7.433
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
Insert
Fig.
1.000 .250
1.000 .250
1.000 .250
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
3
3
4
1
1
2
1
1
2
1
1
2
Counter Clockwise
Page
GROOVING
Dimensions (inch)
GY2M0400G030N-GU
GY2M0400G020N-GS
GY2M0400G030N-GM
(Gauge insert)
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS
F021
GROOVING SYSTEM

1-1
GS

Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Max.
Max.
ar
D1
(R/L)
(inch)
(inch)
.187
.197
Order Number
ID
Modular Blade
Stock
Modular Holder
Stock
.472
.945
(1D1R3H1)
GYM20RA-H12
GYHRUS10B00-M20R
.472
.945
(1F1R3H1)
GYM20RA-H12
GYHRUS12C00-M20R
.315
.551
.984
.315
.551
.984
.315
.551
.984
.315
.551
.984
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
(1F1R4H1)
(1F1R4H2)
(1F1R4H3)
(1H1R4H1)
(1H1R4H2)
(1H1R4H3)
(1K1R4H1)
(1K1R4H2)
(1K1R4H3)
(1M1R4H1)
(1M1R4H2)
(1M1R4H3)
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYHRUS12C00-M25R
GYHRUS16D00-M25R
GYHRUS20D00-M25R
GYHRUS24E00-M25R
a
a
a
a
a
a
a
a
a
a
a
.472
.945
(1D1L3H1)
GYM20LA-H12
GYHLUS10B00-M20L
.472
.945
(1F1L3H1)
GYM20LA-H12
GYHLUS12C00-M20L
.315
.551
.984
.315
.551
.984
.315
.551
.984
.315
.551
.984
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
(1F1L4H1)
(1F1L4H2)
(1F1L4H3)
(1H1L4H1)
(1H1L4H2)
(1H1L4H3)
(1K1L4H1)
(1K1L4H2)
(1K1L4H3)
(1M1L4H1)
(1M1L4H2)
(1M1L4H3)
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYHLUS12C00-M25L
GYHLUS16D00-M25L
GYHLUS20D00-M25L
GYHLUS24E00-M25L
a
a
a
a
a
a
a
a
a
a
a
*
*
*
F022

SPARE PARTS
z
Wrench
TS407
zTKY30R
(Clamp Torque
xTKY15D
: 31 lbf-in)
Fig. 4
Fig. 3
(5 pcs.)
GY06013M
(Clamp Torque
: 53 lbf-in)
TS55
zTKY30R
(Clamp Torque
xTKY25D
: 44 lbf-in)
H1
L1
L2
*3
H2
F1
Cutting Mode
Clockwise
S3
.625
.625 4.500 1.339
.625
.812 .125
.750
.750 5.000 1.339
.750
.875
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
1.000 .250
1.000 .250
1.000 .250
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
3
3
4
1
1
2
1
1
2
1
1
2
.625
.625 4.500 1.339
.625
.812 .125
.750
.750 5.000 1.339
.750
.875
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
4.764
5.000
5.433
5.764
6.000
6.433
5.764
6.000
6.433
6.764
7.000
7.433
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
4.764
5.000
5.433
5.764
6.000
6.433
5.764
6.000
6.433
6.764
7.000
7.433
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
Insert
Fig.
1.000 .250
1.000 .250
1.000 .250
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
3
3
4
1
1
2
1
1
2
1
1
2
Counter Clockwise
Page
GROOVING
Dimensions (inch)
GY2M0475H040N-GU
GY2M0500H040N-GU
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
(Gauge insert)
GY2M0500H040R05-GM
GY2M0500H040L05-GM F012
GY2M0500H040N-MS
GY2M0500H080N-MS
F013
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS
F023
GROOVING SYSTEM

1-1
GS

Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Max.
Max.
ar
D1
(R/L)
(inch)
(inch)
.236
.250
.315
.551
.984
.315
.551
.984
.315
.551
.984
.315
.551
.984
.315
.551
.984
.315
.551
.984
.315
.551
.984
.315
.551
.984
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
.630
1.102
1.969
Order Number
ID
Modular Blade
Stock
(1F1R4J1)
(1F1R4J2)
(1F1R4J3)
(1H1R4J1)
(1H1R4J2)
(1H1R4J3)
(1K1R4J1)
(1K1R4J2)
(1K1R4J3)
(1M1R4J1)
(1M1R4J2)
(1M1R4J3)
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
(1F1L4J1)
(1F1L4J2)
(1F1L4J3)
(1H1L4J1)
(1H1L4J2)
(1H1L4J3)
(1K1L4J1)
(1K1L4J2)
(1K1L4J3)
(1M1L4J1)
(1M1L4J2)
(1M1L4J3)
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
Modular Holder
Stock
GYHRUS12C00-M25R
GYHRUS16D00-M25R
GYHRUS20D00-M25R
GYHRUS24E00-M25R
GYHLUS12C00-M25L
GYHLUS16D00-M25L
GYHLUS20D00-M25L
GYHLUS24E00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 The
*3 Dimensions
shown are when the gauge insert is used. If other insert geometries are used then L1, L2 and F1 values may vary.
*
F024

SPARE PARTS
z
(5 pcs.)

Fig. 4
Fig. 3
x
Wrench
GY06013M
TS55
zTKY30R
(Clamp Torque (Clamp Torque
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
H1
L1
L2
H2
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
4.764
5.000
5.433
5.764
6.000
6.433
5.764
6.000
6.433
6.764
7.000
7.433
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
*3
F1
Cutting Mode
Insert
Fig.
S3
1.000 .250
1.000 .250
1.000 .250
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
Clockwise
3
3
4
1
1
2
1
1
2
1
1
2
Counter Clockwise
Page
GROOVING
Dimensions (inch)
GY2M0600J040N-GU
GY2M0635J040N-GU
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
(Gauge insert)
GY2M0635J040N-GM
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
4.764
5.000
5.433
5.764
6.000
6.433
5.764
6.000
6.433
6.764
7.000
7.433
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
1.299
1.535
1.969
.750
.750
.750
1.000
1.000
1.000
1.250
1.250
1.250
1.500
1.500
1.500
1.000 .250
1.000 .250
1.000 .250
1.125
1.125
1.125
1.375
1.375
1.375
1.625
1.625
1.625
3
3
4
1
1
2
1
1
2
1
1
2
F012
F013
GY2M0600J040N-MS
GY2M0600J080N-MS
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM
F025
GROOVING SYSTEM

2-1
Note 2) Please use left hand modular blade for right hand modular holder and
right hand modular blade for left hand modular holder.
GS

Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Max.
Max.
ar
D1
(R/L)
(inch)
(inch)
.079
.094
.098
L
.118
.125
L
F026
.236
.394
.709
.236
.472
.787
.236
.394
.709
.236
.472
.787
.236
.394
.709
.236
.472
.787
.236
.394
.709
.236
.472
.787
.236
.394
.709
.236
.472
.787
.236
.394
.709
.236
.472
.787
*4
*
Order Number
ID
Modular Blade
Stock
.472
.787
1.417
.472
.945
1.575 2
(2F1R3D1)
(2F1R3D2)
(2F1R3D3)
(2H1R4D1)
(2H1R4D2)
(2H1R4D3)
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
.472
.787
1.417
.472
.945
1.575 2
(2F1L3D1)
(2F1L3D2)
(2F1L3D3)
(2H1L4D1)
(2H1L4D2)
(2H1L4D3)
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
.472
.787
1.417
.472
.945
1.575 2
(2F1R3E1)
(2F1R3E2)
(2F1R3E3)
(2H1R4E1)
(2H1R4E2)
(2H1R4E3)
GYM20LA-E06
GYM20LA-E10
GYM20LB-E18
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
.472
.787
1.417
.472
.945
1.575 2
(2F1L3E1)
(2F1L3E2)
(2F1L3E3)
(2H1L4E1)
(2H1L4E2)
(2H1L4E3)
GYM20RA-E06
GYM20RA-E10
GYM20RB-E18
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
.472
.787
1.417
.472
.945
1.575 2
(2F1R3F1)
(2F1R3F2)
(2F1R3F3)
(2H1R4F1)
(2H1R4F2)
(2H1R4F3)
GYM20LA-F06
GYM20LA-F10
GYM20LB-F18
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
.472
.787
1.417
.472
.945
1.575 2
(2F1L3F1)
(2F1L3F2)
(2F1L3F3)
(2H1L4F1)
(2H1L4F2)
(2H1L4F3)
GYM20RA-F06
GYM20RA-F10
GYM20RB-F18
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
Modular Holder
Stock
GYHRUS12C90-M20L
GYHRUS16D90-M25L
GYHLUS12C90-M20R
GYHLUS16D90-M25R
GYHRUS12C90-M20L
GYHRUS16D90-M25L
GYHLUS12C90-M20R
GYHLUS16D90-M25R
GYHRUS12C90-M20L
GYHRUS16D90-M25L
GYHLUS12C90-M20R
GYHLUS16D90-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 The
*3 Dimensions
*4 The maximumshown
*a : Inventory maintained.

SPARE PARTS
z
GYHRUS12C90-M20L
GYHLUS12C90-M20R
GYHRUS16D90-M25L
GYHLUS16D90-M25R
H1
*3
GY06013M
(Clamp Torque
: 53 lbf-in)
Wrench
TS407
zTKY30R
(Clamp Torque
xTKY15D
: 31 lbf-in)
TS55
(Clamp Torque zTKY30R
xTKY25D
: 44 lbf-in)
Insert
Fig.
L1
L2
H2
F1
.750
.750
.750
.750
.750
.750
1.000 1.000
1.000 1.000
1.000 1.000
5.000
5.000
5.000
6.000
6.000
6.000
1.375
1.375
1.375
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.545
1.781
2.017
1.779
2.094
2.330
1
1
2
1
1
2
.750
.750
.750
.750
.750
.750
1.000 1.000
1.000 1.000
1.000 1.000
5.000
5.000
5.000
6.000
6.000
6.000
1.375
1.375
1.375
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.545
1.781
2.017
1.779
2.094
2.330
1
1
2
1
1
2
.750
.750
.750
.750
.750
.750
1.000 1.000
1.000 1.000
1.000 1.000
5.000
5.000
5.000
6.000
6.000
6.000
1.375
1.375
1.375
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.545
1.781
2.017
1.779
2.094
2.330
1
1
2
1
1
2
Cutting Mode
.750
.750
.750
.750
.750
.750
1.000 1.000
1.000 1.000
1.000 1.000
5.000
5.000
5.000
6.000
6.000
6.000
1.375
1.375
1.375
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.545
1.781
2.017
1.779
2.094
2.330
1
1
2
1
1
2
.750
.750
.750
.750
.750
.750
1.000 1.000
1.000 1.000
1.000 1.000
5.000
5.000
5.000
6.000
6.000
6.000
1.375
1.375
1.375
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.545
1.781
2.017
1.779
2.094
2.330
1
1
2
1
1
2
.750
.750
.750
.750
.750
.750
1.000 1.000
1.000 1.000
1.000 1.000
5.000
5.000
5.000
6.000
6.000
6.000
1.375
1.375
1.375
1.500
1.500
1.500
.750
.750
.750
1.000
1.000
1.000
1.545
1.781
2.017
1.779
2.094
2.330
1
1
2
1
1
2
Page
GY2M0200D020N-GS
GROOVING
Dimensions (inch)
(5 pcs.)
GY2M0200D020N-GM
(Gauge insert)
GY2M0200D020R05-GM
GY2M0200D020L05-GM
F012
F013
GY2M0200D020N-MM
GY2M0200D100N-BM
GY1G0200D020N-GFGS
GY2M0239E020N-GS
GY2M0250E020N-GS
GY2M0239E020N-GM
GY2M0250E020N-GM
(Gauge insert)
GY2M0250E020R05-GM
GY2M0250E020L05-GM
GY2M0250E020N-MM
F012
F013
GY2M0250E125N-BM
GY1G0239E020N-GFGS
GY1G0250E020N-GFGS
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
(Gauge insert)
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS
F012
F013
F027
GROOVING SYSTEM
(EXTERNALGROOVING
))
SERIES(EXTERNAL
GROOVING
GY SERIE
2-1
GS

Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Max.
Max.
ar
D1
(R/L)
(inch)
(inch)
Modular Blade
Stock
Modular Holder
Stock
(2F1R3G1)
GYM20LA-G12
GYHRUS12C90-M20L
(2H1R4G1)
(2H1R4G2)
(2H1R4G3)
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYHRUS16D90-M25L
(2F1L3G1)
GYM20RA-G12
GYHLUS12C90-M20R
(2H1L4G1)
(2H1L4G2)
(2H1L4G3)
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYHLUS16D90-M25R
(2F1R3H1)
GYM20LA-H12
GYHRUS12C90-M20L
(2H1R4H1)
(2H1R4H2)
(2H1R4H3)
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYHRUS16D90-M25L
(2F1L3H1)
GYM20RA-H12
GYHLUS12C90-M20R
(2H1L4H1)
(2H1L4H2)
(2H1L4H3)
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYHLUS16D90-M25R
.630
1.102
1.969 2
(2H1R4J1)
(2H1R4J2)
(2H1R4J3)
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYHRUS16D90-M25L
.630
1.102
1.969 2
(2H1L4J1)
(2H1L4J2)
(2H1L4J3)
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYHLUS16D90-M25R
.630
1.102
1.969 2
.472
.315
.551
.984
.945
R
.187
.197
.315
.551
.984
.315
.551
.984
.315
.551
.984
.315
.551
.984
R
.236
.250
.315
.551
.984
.630
1.102
1.969 2
.945
.472
F028
.945
.472
.630
1.102
1.969 2
a
a
.157
.472
Order Number
ID
.630
1.102
1.969 2
.945
*
*
*
*
a
a
a
a
a
a
a
a
a
a
*21 The
*3 Dimensions
*
a

SPARE PARTS
z
GYHRUS12C90-M20L
GYHLUS12C90-M20R
GYHRUS16D90-M25L
GYHLUS16D90-M25R
H1
.750
L1
L2
H2
F1
1.000 1.000 6.000 1.500 1.000 1.857

1.000 1.000 6.000 1.500 1.000 2.094
1.000 1.000 6.000 1.500 1.000 2.527
1
1
2
.750 1.781
1.000 1.000 6.000 1.500 1.000 1.857

1.000 1.000 6.000 1.500 1.000 2.094
1.000 1.000 6.000 1.500 1.000 2.527
1
1
2
.750
.750 1.781
1.000 1.000 6.000 1.500 1.000 1.857

1.000 1.000 6.000 1.500 1.000 2.094
1.000 1.000 6.000 1.500 1.000 2.527
1
1
2
.750
.750 5.000 1.375
.750 5.000 1.375
TS55
xTKY25D
: 44 lbf-in)
Cutting Mode
.750 5.000 1.375
TS407
xTKY15D
: 31 lbf-in)
Insert
Fig.
.750 1.781
.750
.750 5.000 1.375
*3
GY06013M
(Clamp Torque
: 53 lbf-in)
Wrench
.750 1.781
1.000 1.000 6.000 1.500 1.000 1.857

1.000 1.000 6.000 1.500 1.000 2.094
1.000 1.000 6.000 1.500 1.000 2.527
1
1
2
1.000 1.000 6.000 1.500 1.000 1.857

1.000 1.000 6.000 1.500 1.000 2.094
1.000 1.000 6.000 1.500 1.000 2.527
1
1
2
GY2M0400G030N-GU
GY2M0400G020N-GS
GY2M0400G030N-GM
(Gauge insert)
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS
GY2M0475H040N-GU
GY2M0500H040N-GU
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
(Gauge insert)
GY2M0500H040R05-GM
GY2M0500H040L05-GM
GY2M0500H040N-MS
GY2M0500H080N-MS
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS
1
1
2
F012
F013
F012
F013
GY2M0600J040N-GU
GY2M0635J040N-GU
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
(Gauge insert)
1.000 1.000 6.000 1.500 1.000 1.857

1.000 1.000 6.000 1.500 1.000 2.094
1.000 1.000 6.000 1.500 1.000 2.527
Page
GROOVING
Dimensions (inch)
(5 pcs.)
GY2M0635J040N-GM
GY2M0600J040N-MS
GY2M0600J080N-MS
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM
F012
F013
F029
GROOVING SYSTEM

1-2
00 type holder (Metric)
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Max.
Max.
ar
D1
(R/L)
(mm)
(mm)
2.00
6
10
18
6
10
18
6
12
20
6
12
20
6
12
20
6
12
20
6
10
18
6
10
18
6
12
20
6
12
20
6
12
20
6
12
20
*
*
12
20
36
12
20
36
12
24
40
12
24
40
12
24
40
12
24
40
12
20
36
12
20
36
12
24
40
12
24
40
12
24
40
12
24
40
*
*
*
Order Number
ID
(1C1R3D1)
(1C1R3D2)
(1C1R3D3)
(1E1R3D1)
(1E1R3D2)
(1E1R3D3)
(1E1R4D1)
(1E1R4D2)
(1E1R4D3)
(1G1R4D1)
(1G1R4D2)
(1G1R4D3)
(1Q1R4D1)
(1Q1R4D2)
(1Q1R4D3)
(1J1R4D1)
(1J1R4D2)
(1J1R4D3)
(1C1L3D1)
(1C1L3D2)
(1C1L3D3)
(1E1L3D1)
(1E1L3D2)
(1E1L3D3)
(1E1L4D1)
(1E1L4D2)
(1E1L4D3)
(1G1L4D1)
(1G1L4D2)
(1G1L4D3)
(1Q1L4D1)
(1Q1L4D2)
(1Q1L4D3)
(1J1L4D1)
(1J1L4D2)
(1J1L4D3)
Modular Blade
Stock
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
a
a
Modular Holder
Stock
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*
*
*
*
F030

SPARE PARTS
z
GYHR/L1616J00-M20R/L
Fig. 4
GYHR/L2020K00-M25R/L
GYHR/L2525M00-M25R/L
GYHR/L3225P00-M25R/L
Wrench
TS407
zTKY30R
(Clamp Torque
xTKY15D
: 31 lbf-in)
Fig. 3
(5 pcs.)
GY06013M
(Clamp Torque
: 53 lbf-in)
TS55
xTKY25D
: 44 lbf-in)
*3
Cutting Mode
Insert
Fig.
H1
L1
L2
H2
F1
S3
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
25
25
25
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
25
25
25
32
32
32
104
110
116
119
125
131
117
125
131
142
150
156
162
170
176
162
170
176
104
110
116
119
125
131
117
125
131
142
150
156
162
170
176
162
170
176
28
34
40
28
34
40
31
39
45
31
39
45
31
39
45
31
39
45
28
34
40
28
34
40
31
39
45
31
39
45
31
39
45
31
39
45
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
20
20
20
23
23
23
26
26
26
28
28
28
28
28
28
35
35
35
20
20
20
23
23
23
26
26
26
28
28
28
28
28
28
35
35
35
4
4
4

5
5
5

4
4
4

5
5
5

Clockwise
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
Counter Clockwise
Page
GROOVING
Dimensions (mm)
GY2M0200D020N-GS
GY2M0200D020N-GM
(Gauge insert)
GY2M0200D020R05-GM
GY2M0200D020L05-GM F012
F013
GY2M0200D020N-MM
GY2M0200D100N-BM
GY1G0200D020N-GFGS
F031
GROOVING SYSTEM

1-2

Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Max.
Max.
ar
D1
(R/L)
(mm)
(mm)
2.39
2.50
6
10
18
6
10
18
6
12
20
6
12
20
6
12
20
6
12
20
6
10
18
6
10
18
6
12
20
6
12
20
6
12
20
6
12
20
12
20
36
12
20
36
12
24
40
12
24
40
12
24
40
12
24
40
12
20
36
12
20
36
12
24
40
12
24
40
12
24
40
12
24
40
*
*
*
Order Number
ID
(1C1R3E1)
(1C1R3E2)
(1C1R3E3)
(1E1R3E1)
(1E1R3E2)
(1E1R3E3)
(1E1R4E1)
(1E1R4E2)
(1E1R4E3)
(1G1R4E1)
(1G1R4E2)
(1G1R4E3)
(1Q1R4E1)
(1Q1R4E2)
(1Q1R4E3)
(1J1R4E1)
(1J1R4E2)
(1J1R4E3)
(1C1L3E1)
(1C1L3E2)
(1C1L3E3)
(1E1L3E1)
(1E1L3E2)
(1E1L3E3)
(1E1L4E1)
(1E1L4E2)
(1E1L4E3)
(1G1L4E1)
(1G1L4E2)
(1G1L4E3)
(1Q1L4E1)
(1Q1L4E2)
(1Q1L4E3)
(1J1L4E1)
(1J1L4E2)
(1J1L4E3)
Modular Blade
Stock
GYM20RA-E06
GYM20RA-E10
GYM20RB-E18
GYM20RA-E06
GYM20RA-E10
GYM20RB-E18
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM20LA-E06
GYM20LA-E10
GYM20LB-E18
GYM20LA-E06
GYM20LA-E10
GYM20LB-E18
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
a
a
Modular Holder
Stock
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*
*
*
*
F032

SPARE PARTS
z
Wrench
TS407
zTKY30R
(Clamp Torque xTKY15D
: 31 lbf-in)
Fig. 4
Fig. 3
(5 pcs.)
GY06013M
(Clamp Torque
: 53 lbf-in)
TS55
zTKY30R
(Clamp Torque
xTKY25D
: 44 lbf-in)
*3
Cutting Mode
Insert
Fig.
H1
L1
L2
H2
F1
S3
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
25
25
25
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
25
25
25
32
32
32
104
110
116
119
125
131
117
125
131
142
150
156
162
170
176
162
170
176
104
110
116
119
125
131
117
125
131
142
150
156
162
170
176
162
170
176
28
34
40
28
34
40
31
39
45
31
39
45
31
39
45
31
39
45
28
34
40
28
34
40
31
39
45
31
39
45
31
39
45
31
39
45
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
20
20
20
23
23
23
26
26
26
28
28
28
28
28
28
35
35
35
20
20
20
23
23
23
26
26
26
28
28
28
28
28
28
35
35
35
4
4
4

5
5
5

4
4
4

5
5
5

Clockwise
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
Counter Clockwise
Page
GROOVING
Dimensions (mm)
GY2M0239E020N-GS
GY2M0250E020N-GS
GY2M0239E020N-GM
GY2M0250E020N-GM
(Gauge insert)
GY2M0250E020R05-GM
GY2M0250E020L05-GM F012
F013
GY2M0250E020N-MM
GY2M0250E125N-BM
GY1G0239E020N-GFGS
GY1G0250E020N-GFGS
F033
GROOVING SYSTEM

1-2
GS

Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Max.
Max.
ar
D1
(R/L)
(mm)
(mm)
3.00
3.18
6
10
18
6
10
18
6
12
20
6
12
20
6
12
20
6
12
20
6
10
18
6
10
18
6
12
20
6
12
20
6
12
20
6
12
20
12
20
36
12
20
36
12
24
40
12
24
40
12
24
40
12
24
40
12
20
36
12
20
36
12
24
40
12
24
40
12
24
40
12
24
40
Order Number
ID
(1C1R3F1)
(1C1R3F2)
(1C1R3F3)
(1E1R3F1)
(1E1R3F2)
(1E1R3F3)
(1E1R4F1)
(1E1R4F2)
(1E1R4F3)
(1G1R4F1)
(1G1R4F2)
(1G1R4F3)
(1Q1R4F1)
(1Q1R4F2)
(1Q1R4F3)
(1J1R4F1)
(1J1R4F2)
(1J1R4F3)
(1C1L3F1)
(1C1L3F2)
(1C1L3F3)
(1E1L3F1)
(1E1L3F2)
(1E1L3F3)
(1E1L4F1)
(1E1L4F2)
(1E1L4F3)
(1G1L4F1)
(1G1L4F2)
(1G1L4F3)
(1Q1L4F1)
(1Q1L4F2)
(1Q1L4F3)
(1J1L4F1)
(1J1L4F2)
(1J1L4F3)
Modular Blade
Stock
GYM20RA-F06
GYM20RA-F10
GYM20RB-F18
GYM20RA-F06
GYM20RA-F10
GYM20RB-F18
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM20LA-F06
GYM20LA-F10
GYM20LB-F18
GYM20LA-F06
GYM20LA-F10
GYM20LB-F18
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
a
a
Modular Holder
Stock
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*
*
*
*
F034

SPARE PARTS
z
Fig. 4
Wrench
TS407
zTKY30R
(Clamp Torque
xTKY15D
: 31 lbf-in)
Fig. 3
(5 pcs.)
GY06013M
(Clamp Torque
: 53 lbf-in)
TS55
xTKY25D
: 44 lbf-in)
*3
Cutting Mode
Insert
Fig.
H1
L1
L2
H2
F1
S3
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
25
25
25
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
25
25
25
32
32
32
104
110
116
119
125
131
117
125
131
142
150
156
162
170
176
162
170
176
104
110
116
119
125
131
117
125
131
142
150
156
162
170
176
162
170
176
28
34
40
28
34
40
31
39
45
31
39
45
31
39
45
31
39
45
28
34
40
28
34
40
31
39
45
31
39
45
31
39
45
31
39
45
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
16
16
16
20
20
20
20
20
20
25
25
25
32
32
32
32
32
32
20
20
20
23
23
23
26
26
26
28
28
28
28
28
28
35
35
35
20
20
20
23
23
23
26
26
26
28
28
28
28
28
28
35
35
35
4
4
4

5
5
5

4
4
4

5
5
5

Clockwise
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
3
3
4
1
1
2
3
3
4
1
1
2
1
1
2
1
1
2
Counter Clockwise
Page
GROOVING
Dimensions (mm)
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
(Gauge insert)
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
F012
F013
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS
F035
GROOVING SYSTEM

1-2
GS

Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Max.
Max.
ar
D1
(R/L)
(mm)
(mm)
4.00
Order Number
ID
Modular Blade
Stock
Modular Holder
Stock
12
24
(1C1R3G1)
GYM20RA-G12
GYHR1616J00-M20R
12
24
(1E1R3G1)
GYM20RA-G12
GYHR2020K00-M20R
8
14
25
8
14
25
8
14
25
8
14
25
16
28
50
16
28
50
16
28
50
16
28
50
(1E1R4G1)
(1E1R4G2)
(1E1R4G3)
(1G1R4G1)
(1G1R4G2)
(1G1R4G3)
(1Q1R4G1)
(1Q1R4G2)
(1Q1R4G3)
(1J1R4G1)
(1J1R4G2)
(1J1R4G3)
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
a
a
a
a
a
a
a
a
a
a
a
12
24
(1C1L3G1)
GYM20LA-G12
GYHL1616J00-M20L
12
24
(1E1L3G1)
GYM20LA-G12
GYHL2020K00-M20L
8
14
25
8
14
25
8
14
25
8
14
25
16
28
50
16
28
50
16
28
50
16
28
50
(1E1L4G1)
(1E1L4G2)
(1E1L4G3)
(1G1L4G1)
(1G1L4G2)
(1G1L4G3)
(1Q1L4G1)
(1Q1L4G2)
(1Q1L4G3)
(1J1L4G1)
(1J1L4G2)
(1J1L4G3)
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
*
*
*
F036

SPARE PARTS
z
Wrench
TS407
zTKY30R
(Clamp Torque
xTKY15D
)
: 31 lbf-in
Fig. 4
Fig. 3
(5 pcs.)
GY06013M
(Clamp Torque
: 53 lbf-in)
TS55
xTKY25D
: 44 lbf-in)
*3
Cutting Mode
Insert
Fig.
H1
L1
L2
H2
F1
S3
Clockwise
16
16
110
34
16
20
20
20
125
34
20
23
20
20
20
25
25
25
32
32
32
32
32
32
20
20
20
25
25
25
25
25
25
32
32
32
119
125
136
144
150
161
164
170
181
164
170
181
33
39
50
33
39
50
33
39
50
33
39
50
20
20
20
25
25
25
32
32
32
32
32
32
26
26
26
28
28
28
28
28
28
35
35
35
5
5
5

3
3
4
1
1
2
1
1
2
1
1
2
16
16
110
34
16
20
20
20
125
34
20
23
20
20
20
25
25
25
32
32
32
32
32
32
20
20
20
25
25
25
25
25
25
32
32
32
119
125
136
144
150
161
164
170
181
164
170
181
33
39
50
33
39
50
33
39
50
33
39
50
20
20
20
25
25
25
32
32
32
32
32
32
26
26
26
28
28
28
28
28
28
35
35
35
5
5
5

3
3
4
1
1
2
1
1
2
1
1
2
Counter Clockwise
Page
GROOVING
Dimensions (mm)
GY2M0400G030N-GU
GY2M0400G020N-GS
GY2M0400G030N-GM
(Gauge insert)
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS
F037
GROOVING SYSTEM

1-2
GS

Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Max.
Max.
ar
D1
(R/L)
(mm)
(mm)
4.75
5.00
Order Number
ID
Modular Blade
Stock
Modular Holder
Stock
12
24
(1C1R3H1)
GYM20RA-H12
GYHR1616J00-M20R
12
24
(1E1R3H1)
GYM20RA-H12
GYHR2020K00-M20R
8
14
25
8
14
25
8
14
25
8
14
25
16
28
50
16
28
50
16
28
50
16
28
50
(1E1R4H1)
(1E1R4H2)
(1E1R4H3)
(1G1R4H1)
(1G1R4H2)
(1G1R4H3)
(1Q1R4H1)
(1Q1R4H2)
(1Q1R4H3)
(1J1R4H1)
(1J1R4H2)
(1J1R4H3)
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
a
a
a
a
a
a
a
a
a
a
a
12
24
(1C1L3H1)
GYM20LA-H12
GYHL1616J00-M20L
12
24
(1E1L3H1)
GYM20LA-H12
GYHL2020K00-M20L
8
14
25
8
14
25
8
14
25
8
14
25
16
28
50
16
28
50
16
28
50
16
28
50
(1E1L4H1)
(1E1L4H2)
(1E1L4H3)
(1G1L4H1)
(1G1L4H2)
(1G1L4H3)
(1Q1L4H1)
(1Q1L4H2)
(1Q1L4H3)
(1J1L4H1)
(1J1L4H2)
(1J1L4H3)
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
*
*
*
F038

SPARE PARTS
z
Fig. 4
Wrench
TS407
zTKY30R
(Clamp Torque
xTKY15D
: 31 lbf-in)
Fig. 3
(5 pcs.)
GY06013M
(Clamp Torque
: 53 lbf-in)
TS55
zTKY30R
(Clamp Torque
xTKY25D
: 44 lbf-in)
*3
Cutting Mode
Insert
Fig.
H1
L1
L2
H2
F1
S3
16
16
110
34
16
20
20
20
125
34
20
23
20
20
20
25
25
25
32
32
32
32
32
32
20
20
20
25
25
25
25
25
25
32
32
32
119
125
136
144
150
161
164
170
181
164
170
181
33
39
50
33
39
50
33
39
50
33
39
50
20
20
20
25
25
25
32
32
32
32
32
32
26
26
26
28
28
28
28
28
28
35
35
35
5
5
5

3
3
4
1
1
2
1
1
2
1
1
2
16
16
110
34
16
20
20
20
125
34
20
23
20
20
20
25
25
25
32
32
32
32
32
32
20
20
20
25
25
25
25
25
25
32
32
32
119
125
136
144
150
161
164
170
181
164
170
181
33
39
50
33
39
50
33
39
50
33
39
50
20
20
20
25
25
25
32
32
32
32
32
32
26
26
26
28
28
28
28
28
28
35
35
35
5
5
5

3
3
4
1
1
2
1
1
2
1
1
2
Clockwise
Counter Clockwise
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Dimensions (mm)
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
(Gauge insert)
GY2M0500H040R05-GM
GY2M0500H040L05-GM F012
F013
GY2M0500H040N-MS
GY2M0500H080N-MS
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS
F039
GROOVING SYSTEM

1-2
GS

Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Max.
Max.
ar
D1
(R/L)
(mm)
(mm)
6.00
6.35
8
14
25
8
14
25
8
14
25
8
14
25
8
14
25
8
14
25
8
14
25
8
14
25
16
28
50
16
28
50
16
28
50
16
28
50
16
28
50
16
28
50
16
28
50
16
28
50
Order Number
ID
Modular Blade
Stock
(1E1R4J1)
(1E1R4J2)
(1E1R4J3)
(1G1R4J1)
(1G1R4J2)
(1G1R4J3)
(1Q1R4J1)
(1Q1R4J2)
(1Q1R4J3)
(1J1R4J1)
(1J1R4J2)
(1J1R4J3)
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
(1E1L4J1)
(1E1L4J2)
(1E1L4J3)
(1G1L4J1)
(1G1L4J2)
(1G1L4J3)
(1Q1L4J1)
(1Q1L4J2)
(1Q1L4J3)
(1J1L4J1)
(1J1L4J2)
(1J1L4J3)
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
Modular Holder
Stock
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 The
*3 Dimensions
*
F040

SPARE PARTS
z
Fig. 3
Fig. 4
(5 pcs.)
Wrench
GY06013M
TS55
(Clamp Torque (Clamp Torque zTKY30R
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
*3
Cutting Mode
Insert
Fig.
H1
L1
L2
H2
F1
S3
20
20
20
25
25
25
32
32
32
32
32
32
20
20
20
25
25
25
25
25
25
32
32
32
119
125
136
144
150
161
164
170
181
164
170
181
33
39
50
33
39
50
33
39
50
33
39
50
20
20
20
25
25
25
32
32
32
32
32
32
26
26
26
28
28
28
28
28
28
35
35
35
5
5
5

Clockwise
3
3
4
1
1
2
1
1
2
1
1
2
Counter Clockwise
Page
GROOVING
Dimensions (mm)
GY2M0600J040N-GU
GY2M0635J040N-GU
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
(Gauge insert)
GY2M0635J040N-GM
20
20
20
25
25
25
32
32
32
32
32
32
20
20
20
25
25
25
25
25
25
32
32
32
119
125
136
144
150
161
164
170
181
164
170
181
33
39
50
33
39
50
33
39
50
33
39
50
20
20
20
25
25
25
32
32
32
32
32
32
26
26
26
28
28
28
28
28
28
35
35
35
5
5
5

3
3
4
1
1
2
1
1
2
1
1
2
F012
F013
GY2M0600J040N-MS
GY2M0600J080N-MS
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM
F041
GROOVING SYSTEM

2-2
GS

Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Max.
Max.
ar
D1
(R/L)
(mm)
(mm)
2.00
2.39
2.50
L
3.00
3.18
L
F042
6
10
18
6
12
20
6
10
18
6
12
20
6
10
18
6
12
20
6
10
18
6
12
20
6
10
18
6
12
20
6
10
18
6
12
20
12
20
36
12
24
40
12
20
36
12
24
40
12
20
36
12
24
40
12
20
36
12
24
40
12
20
36
12
24
40
12
20
36
12
24
40
Order Number
ID
Modular Blade
Stock
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
(2E1R3D1)
(2E1R3D2)
(2E1R3D3)
(2G1R4D1)
(2G1R4D2)
(2G1R4D3)
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
(2E1L3D1)
(2E1L3D2)
(2E1L3D3)
(2G1L4D1)
(2G1L4D2)
(2G1L4D3)
GYM20LA-E06
GYM20LA-E10
GYM20LB-E18
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
(2E1R3E1)
(2E1R3E2)
(2E1R3E3)
(2G1R4E1)
(2G1R4E2)
(2G1R4E3)
GYM20RA-E06
GYM20RA-E10
GYM20RB-E18
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
(2E1L3E1)
(2E1L3E2)
(2E1L3E3)
(2G1L4E1)
(2G1L4E2)
(2G1L4E3)
GYM20LA-F06
GYM20LA-F10
GYM20LB-F18
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
(2E1R3F1)
(2E1R3F2)
(2E1R3F3)
(2G1R4F1)
(2G1R4F2)
(2G1R4F3)
GYM20RA-F06
GYM20RA-F10
GYM20RB-F18
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
(2E1L3F1)
(2E1L3F2)
(2E1L3F3)
(2G1L4F1)
(2G1L4F2)
(2G1L4F3)
Modular Holder
Stock
GYHR2020K90-M20L
GYHR2525M90-M25L
GYHL2020K90-M20R
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHR2525M90-M25L
GYHL2020K90-M20R
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHR2525M90-M25L
GYHL2020K90-M20R
GYHL2525M90-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 The
*3 Dimensions
*4 The maximumshown

SPARE PARTS
z
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
*3
GY06013M
(Clamp Torque
: 53 lbf-in)
Wrench
TS407
xTKY15D
: 31 lbf-in)
TS55
xTKY25D
: 44 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
20
20
20
25
25
25
20
20
20
25
25
25
125
125
125
150
150
150
35
35
35
38
38
38
20
20
20
25
25
25
39
45
51
45
53
59
1
1
2
1
1
2
20
20
20
25
25
25
20
20
20
25
25
25
125
125
125
150
150
150
35
35
35
38
38
38
20
20
20
25
25
25
39
45
51
45
53
59
1
1
2
1
1
2
20
20
20
25
25
25
20
20
20
25
25
25
125
125
125
150
150
150
35
35
35
38
38
38
20
20
20
25
25
25
39
45
51
45
53
59
1
1
2
1
1
2
20
20
20
25
25
25
20
20
20
25
25
25
125
125
125
150
150
150
35
35
35
38
38
38
20
20
20
25
25
25
39
45
51
45
53
59
1
1
2
1
1
2
20
20
20
25
25
25
20
20
20
25
25
25
125
125
125
150
150
150
35
35
35
38
38
38
20
20
20
25
25
25
39
45
51
45
53
59
1
1
2
1
1
2
20
20
20
25
25
25
20
20
20
25
25
25
125
125
125
150
150
150
35
35
35
38
38
38
20
20
20
25
25
25
39
45
51
45
53
59
1
1
2
1
1
2
Cutting Mode
Page
GY2M0200D020N-GS
GROOVING
Dimensions (mm)
(5 pcs.)
GY2M0200D020N-GM
(Gauge insert)
GY2M0200D020R05-GM
GY2M0200D020L05-GM
F012
F013
GY2M0200D020N-MM
GY2M0200D100N-BM
GY1G0200D020N-GFGS
GY2M0239E020N-GS
GY2M0250E020N-GS
GY2M0239E020N-GM
GY2M0250E020N-GM
(Gauge insert)
GY2M0250E020R05-GM
GY2M0250E020L05-GM
F012
F013
GY2M0250E020N-MM
GY2M0250E125N-BM
GY1G0239E020N-GFGS
GY1G0250E020N-GFGS
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
(Gauge insert)
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS
F012
F013
F043
GROOVING SYSTEM

2-2
GS

Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Max.
Max.
ar
D1
(R/L)
(mm)
(mm)
R
4.75
5.00
L
Modular Holder
Stock
GYHR2020K90-M20L
GYHR2525M90-M25L
GYHL2020K90-M20R
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHR2525M90-M25L
GYHL2020K90-M20R
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
24
(2E1R3G1)
GYM20LA-G12
8
14
25
16
28
50
(2G1R4G1)
(2G1R4G2)
(2G1R4G3)
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
a
a
12
24
(2E1L3G1)
GYM20RA-G12
8
14
25
16
28
50
(2G1L4G1)
(2G1L4G2)
(2G1L4G3)
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
6.00
6.35
a
a
24
(2E1R3H1)
GYM20LA-H12
8
14
25
16
28
50
(2G1R4H1)
(2G1R4H2)
(2G1R4H3)
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
a
a
12
24
(2E1L3H1)
GYM20RA-H12
8
14
25
(2G1L4H1)
(2G1L4H2)
(2G1L4H3)
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
16
28
50
(2G1R4J1)
(2G1R4J2)
(2G1R4J3)
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
16
28
50
(2G1L4J1)
(2G1L4J2)
(2G1L4J3)
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
16
28
50
8
14
25
12
F044
Stock
12
8
14
25
Modular Blade
4.00
Order Number
ID
*
*
*
*
a
a
a
a
a
a
*21 The
*3 Dimensions
*
a

SPARE PARTS
z
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
*3*3
TS407
xTKY15D
GY06013M
: 31 lbf-in)
(Clamp Torque
TS55
: 53 lbf-in)
xTKY25D
: 44 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
20
20
125
35
20
45
25
25
25
25
25
25
150
150
150
38
38
38
25
25
25
47
53
64
1
1
2
Cutting Mode
20
20
125
35
20
45
25
25
25
25
25
25
150
150
150
38
38
38
25
25
25
47
53
64
1
1
2
20
20
125
35
20
45
25
25
25
25
25
25
150
150
150
38
38
38
25
25
25
47
53
64
1
1
2
20
20
125
35
20
45
25
25
25
25
25
25
150
150
150
38
38
38
25
25
25
47
53
64
1
1
2
25
25
25
25
25
25
150
150
150
38
38
38
25
25
25
47
53
64
1
1
2
25
25
25
150
150
150
38
38
38
25
25
25
47
53
64
1
1
2
Page
GY2M0400G030N-GU
GY2M0400G020N-GS
GY2M0400G030N-GM
(Gauge insert)
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS
F012
F013
GY2M0475H040N-GU
GY2M0500H040N-GU
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
(Gauge insert)
GY2M0500H040R05-GM
GY2M0500H040L05-GM
GY2M0500H040N-MS
GY2M0500H080N-MS
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS
F012
F013
GY2M0600J040N-GU
GY2M0635J040N-GU
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
(Gauge insert)
25
25
25
Wrench
GROOVING
Dimensions (mm)
(5 pcs.)
GY2M0635J040N-GM
GY2M0600J040N-MS
GY2M0600J080N-MS
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM
F012
F013
F045
GROOVING SYSTEM
Recommended Cutting Conditions [External Grooving]
are the recommended cutting conditions when using

*Below
the modular holder GYHR/LUS16D00-M25R/L with the
modular blade GYM25oA-oo.
y Recommended feed rate and depth of cut
a Grooving, Cutting off
Feed (inch/rev)
a Grooving (Finishing)
Insert width (inch)
Insert width (inch)
Insert width (inch)
Flat Top GFGS (CBN)
GM Breaker
GS Breaker
Insert width (inch)
GU Breaker
: 1st recommended area
Feed (inch/rev)
Feed (inch/rev)
Feed (inch/rev)
MS Breaker
a Turning
Insert width (inch)
GROOVING
: 1st
recommended area
Radial Depth of cut (inch)
a Grooving
Insert width .236"

Insert width .197"
Insert width .157"
Insert width .118"
Feed (inch/rev)
Feed (inch/rev)
MM Breaker
a Turning
Insert width (inch)
: 1st
recommended area
a Grooving
Insert width .236"

Insert width .197"
Insert width .157"
Insert width
.118"
Insert width .098"
Insert width .079"
Feed (inch/rev)
Feed (inch/rev)
BM Breaker
a Copying
Insert width (inch)
: 1st
recommended area
Feed (inch/rev)
a Grooving
Insert width
.197"
Insert width .187"
.157"
Insert width .250"

.236"
Insert width
.125"
.118"
Insert width
.098"
Insert width
.079"
Feed (inch/rev)
(Note) When using a combination as shown below, decrease the recommended feed rate by 20% and 40% respectively.
a Decrease the feed rate by 40%.
a Decrease the feed rate by 20%.
(.750".750" Square holder)
F046
(.625".625" Square holder)
Limitation of the maximum groove depth

When using the modular blade GYMiiR/LA- ii
Max. Groove Depth

ar (Max.)
The maximum groove depth is not limited by the workpiece diameter.
When using the modular blade GYMiiR/LB- iii

The maximum groove depth is limited by the workpiece diameter.
Max. Groove Depth
e
iec r
kp te
or ame
W Di
Workpiece Diameter
Recommended Cutting Speed (SFM)

Work Material
Hardness
Insert Grade
165
330
VP20RT
825
990
720
360
VP10RT
Mild Steel
Cutting Speed (SFM)

495
660
330
GROOVING
Due to the interference on

this part, the maximum
groove depth is limited
by the workpiece diameter.
755
< 160HB
460
MY5015
990
295
NX2525
690
260
VP20RT
590
295
VP10RT
625
160-280HB
360
MY5015
230
NX2525
Carbon Steel
Alloy Steel
825
560
195
VP20RT
460
230
VP10RT
495
> 280HB
295
MY5015
NX2525
180
440
195
VP20RT
Stainless Steel
460
< 270HB
230
VP10RT
K
Tensile Strength
< 300MPa
495
260
VP20RT
Cast Iron
690
590
295
VP10RT
625
460
MY5015
195
VP20RT
Ductile Cast Iron
Tensile Strength
< 800MPa
VP20RT
Heat Resistant Alloy

Titanium Alloy
Hardened steel
> 50HRC
VP10RT
MB8025
495
295
MY5015
460
230
VP10RT
990
690
100 195
130 230
260
395
F047
GROOVING SYSTEM
Tool Selection
a Notes when selecting the tool body

Modular blade (1)
Modular holder
Modular holder
Modular holder
aTo ensure sufcient clamping rigidity, select a modular holder
aIf there is no restriction for use, select the largest modular
with the largest possible shank size.
blade for the same shank size.
Modular blade (3)
GROOVING
Modular blade (2)
aSelect the shortest possible blade suitable

aSelect the shortest possible blade suitable for the application.
for the application.
: Recommended.
a Notes when setting the tool

Tool body setting angle
Setting of cutting edge height
90
90
<Grooving/Cross-feed machining>
Set the cutting edge height to .004" parallel to the central axis.
<Cutting off>
Set the cutting edge height to 0+.008" parallel to the central axis.
aSet the insert perpendicular to the central axis.
Overhang
Good
NG
aWhen setting the tool, ensure that the overhang is as short as possible.
F048
Machining Recommendations
a Notes on multi-functional machining (MS and MM breakers)

Machining narrow grooves
Machining wide grooves
xcz
aIt is recommended to carry out plunging in several passes.
aIt is recommended that cross-feed machining is used.
Following the steps above makes it difcult for chips to elongate.

This also improves the accuracy of workpiece wall surface.

Roughing
GROOVING
Finishing
z Carry out grooving. c Carry out cross feed

x Retract the tool
machining.
v Retract the tool approx
approx .004".
.004".
b Carry out grooving.

n Retract the tool approx
.004".
* Repeat the steps z n.
m Carry out grooving

to the end point of
the corner radius.
, Machining of the wall

surface, corner radius and
bottom face should be
carried out in one process.
Precautions when nishing walls
Finishing
.
/
. Stop at the bottom of

the corner radius.
/ Machine the counter

wall to the corner radius
in one process.
Finish machining.
Wall machining
aTo produce high accuracy walls using MS or MM breaker insert,
do not carry out back turning. Plunging is recommended.
Machining of a ring section
aWhen machining a wall, chip jamming can occur. In this case, stop
aWhen a ring remains in a cross feed end process,
cross feed machining just before the wall (at a point less than the
insert width) then remove the remaining material by plunging.
nish cross feed machining .040" .059" short of

the end point, then remove the ring by plunging.
F049
GROOVING SYSTEM
Machining Recommendations
a Notes on multi-functional machining (BM breaker)

Roughing
ap
aWith the BM breaker insert, 3 dimensional copying is possible.
Set the depth of cut (ap) to 40% less than the insert width.
aUse plunging and cross-feed machining.
When machining the corner, vibration is likely to occur. To avoid

this, reduce the feed by 50%.
GROOVING
Finishing
Insert
ap (inch)
GY2M0200D100N-BM
.002
GY2M0250E125N-BM
.004
GY2M0300F150N-BM
.006
GY2M0318F159N-BM
GY2M0400G200N-BM
ap
aCarry out nishing in one process.
For the depth of cut (ap) when back turning, refer to the table on the right.
GY2M0475H238N-BM
.009
GY2M0500H250N-BM
GY2M0600J150N-BM
GY2M0635J318N-BM
F050
.008
.012
a Notes for cutting off

feed
Distance from the cutting edge
to the workpiece center
<Feed>
a When the cutting edge approaches the center, reduce the feed by
50%.
a If necessary, stop the feed prior to reaching the center of the
workpiece. The part will fall off because of its own weight.
Feed f
Revolution
Distance from the cutting edge
to the workpiece center
<Spindle speed>
a When using constant cutting speed during a cutting off cycle, it is
recommended to limit the spindle speed to 80% of maximum to

ensure stability.
GROOVING
Distance a
a To prevent the workpiece from being expelled, lower the spindle
speed before nishing the grooving operation.
Maximum spindle speed
Revolution n
max-n
start-n
Distance a
insert
Neutral insert
Handed insert
Neutral insert
Handed insert
a When there is a center stub on solid bar work or burrs are formed on pipe material, it is possible to decrease them by using a handed insert.
With a handed insert, machining tends to be less stable when compared to using a neutral insert. Pay special attention to avoid fracturing of
the cutting edge and decrease the feed when necessary.
F051
GROOVING SYSTEM
ASSEMBLY INSTRUCTION
a Assembly Procedures
(b) Wrench
(d) Wrench
Holder
(a) Insert clamp screw
x 1pc.
Modular Blade
(Ex.)
x
c
GY M25R A - F 20
GY M25R A - F 12
(c) Modular blade

set screw x 5pcs.
z
(Ex.) GYHRUS16D00 - M25R
GYHR2525M00 - M25R
v
Insert
(Ex.)GY2M0300 F 040N-MS
GY2M0318 F 030N-GM
Note 1) c and v are changed by the insert size.
GROOVING
B'
Side Screws
(3 screws)
Side Screws
(2 screws)
Short, Medium
Modular Blade
(4 holes)
Long
Modular Blade
(5 holes)
Note 2) z and x should be matched. (See caption A)
Note 4)
Please clean the insert-seat
before installing the insert.
Front Screws
(2 screws)
Note 3)
Please tighten the modular
blade setscrews in order of
[Side screws] [Front screws].
Note 5)
c and v should be matched.
(See caption A)
E
Good
Note 6)
Dont tighten the insert clamp
screw without installing the insert.
This will prevent modular blade damage.
F052
Short,
Medium
(4 holes)
Long
(5 holes)
NG
Note 7)
The insert clamp screw is inclined.
Ensure that the wrench is perpendicular to the
screw tightening.
Assembled
Memo
F053
GROOVING SYSTEM
GY SERIES (FACE GROOVING)

3-1
Note 2) Please use right hand modular blade for right hand modular holder.

GS
F1
W3
ar
L1
Insert GY2Mooooooooo-BM
L2
L2
H1
H1
H2
Fig. 2
H2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.118
.125
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
Order Number
ID
Modular Blade
Stock
1.378
1.575
.472
(4F1R4F11) GYM25RD-F12-035
1.575
1.969
.472
(4F1R4F12) GYM25RD-F12-040
1.969
2.362
.472
(4F1R4F13) GYM25RD-F12-050
2.362
2.953
3.937
3.937
5.906
5.315
7.874
7.087
9.843
(4F1R4F14) GYM25RD-F12-060
1 (4F1R4F24) GYM25RD-F20-060
(4F1R4F15) GYM25RD-F12-075
1 (4F1R4F25) GYM25RD-F20-075
(4F1R4F16) GYM25RD-F12-100
1 (4F1R4F26) GYM25RD-F20-100
(4F1R4F17) GYM25RD-F12-135
1 (4F1R4F27) GYM25RD-F20-135
(4F1R4F18) GYM25RD-F12-180
1 (4F1R4F28) GYM25RD-F20-180
2.953
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
1.378
1.575
.472
(4H1R4F11) GYM25RD-F12-035
1.575
1.969
.472
(4H1R4F12) GYM25RD-F12-040
1.969
2.362
.472
(4H1R4F13) GYM25RD-F12-050
2.362
2.953
3.937
3.937
5.906
5.315
7.874
7.087
9.843
(4H1R4F14) GYM25RD-F12-060
1 (4H1R4F24) GYM25RD-F20-060
(4H1R4F15) GYM25RD-F12-075
1 (4H1R4F25) GYM25RD-F20-075
(4H1R4F16) GYM25RD-F12-100
1 (4H1R4F26) GYM25RD-F20-100
(4H1R4F17) GYM25RD-F12-135
1 (4H1R4F27) GYM25RD-F20-135
(4H1R4F18) GYM25RD-F12-180
1 (4H1R4F28) GYM25RD-F20-180
2.953
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
*
*
*
*
*
*
*
*
*
*
a
a
Modular Holder
Stock
GYHRUS12C00-M25R
GYHRUS16D00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
are when the gauge insert is used. If other insert geometries are used then L1, L2, F1 and D1 values may vary.
*3 Refer to pageshown
F058 for left hand tools.
*
Notes when selecting a modular blade (1)

a Select a modular blade for face grooving, so that the cutting diameter at
the rst pass is within the range of D1 minimum and D1 maximum that
are described in the table of dimensions.
F054
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
Fig. 4
GYHRUS12C00-M25R
GYHRUS16D00-M25R
Dimensions (inch)
H1
L1
L2
H2
*2
F1
.750 1.000 .250
.750
.750 5.000 1.535
.750 1.000 .250
.750
.750 5.000 1.535
.750 1.000 .250
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
3
4
3
4
3
4
3
4
3
4
1.000 1.000 6.000 1.535 1.000 1.125
1.000 1.000 6.000 1.535 1.000 1.125
1.000 1.000 6.000 1.535 1.000 1.125
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000

1
2
1
2
1
2
1
2
1
2
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.236
6.000
6.236
6.000
6.236
6.000
6.236
6.000
6.236
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
GY06013M
TS55
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Cutting Mode
S3
.750 5.000 1.535
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
Wrench
Insert
Fig.
.750
5.000
5.236
5.000
5.236
5.000
5.236
5.000
5.236
5.000
5.236
(5 pcs.)
Page
GROOVING
Fig. 3
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
F012
F013
(Gauge insert)
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS

a When machining wide face grooves, select a modular blade suitable
for the maximum diameter and machine from the outer diameter
towards the center.
a When machining toward the center, there is no restriction cutting
diameter.
a For details, please refer to page F128.
F055
GROOVING SYSTEM

3-1
00 type holder (Inch) NEW

GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.118
.125
Hand
(R/L)
*3
Max.
First Cut Diameter
Groove Depth
D1 (inch)
ar
Min.
Max.
(inch)
Order Number
ID
Modular Blade
Stock
1.378
1.575
.472
(4K1R4F11) GYM25RD-F12-035
1.575
1.969
.472
(4K1R4F12) GYM25RD-F12-040
1.969
2.362
.472
(4K1R4F13) GYM25RD-F12-050
2.362
2.953
3.937
3.937
5.906
5.315
7.874
7.087
9.843
(4K1R4F14) GYM25RD-F12-060
1 (4K1R4F24) GYM25RD-F20-060
(4K1R4F15) GYM25RD-F12-075
1 (4K1R4F25) GYM25RD-F20-075
(4K1R4F16) GYM25RD-F12-100
1 (4K1R4F26) GYM25RD-F20-100
(4K1R4F17) GYM25RD-F12-135
1 (4K1R4F27) GYM25RD-F20-135
(4K1R4F18) GYM25RD-F12-180
1 (4K1R4F28) GYM25RD-F20-180
2.953
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
1.378
1.575
.472
(4M1R4F11) GYM25RD-F12-035
1.575
1.969
.472
(4M1R4F12) GYM25RD-F12-040
1.969
2.362
.472
(4M1R4F13) GYM25RD-F12-050
2.362
2.953
3.937
3.937
5.906
5.315
7.874
7.087
9.843
(4M1R4F14) GYM25RD-F12-060
1 (4M1R4F24) GYM25RD-F20-060
(4M1R4F15) GYM25RD-F12-075
1 (4M1R4F25) GYM25RD-F20-075
(4M1R4F16) GYM25RD-F12-100
1 (4M1R4F26) GYM25RD-F20-100
(4M1R4F17) GYM25RD-F12-135
1 (4M1R4F27) GYM25RD-F20-135
(4M1R4F18) GYM25RD-F12-180
1 (4M1R4F28) GYM25RD-F20-180
2.953
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
*
*
*
*
*
*
*
*
*
*
a
a
Modular Holder
Stock
GYHRUS20D00-M25R
GYHRUS24E00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F056
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHRUS20D00-M25R
GYHRUS24E00-M25R
H1
L1
L2
*2
H2

1
1.250 1.250 6.000
1.535 1.250 1.375
1.250 1.250 6.000
1.535 1.250 1.375
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1
2
1
2
1
2
1
2
1
2
1.500 1.500 7.000
1.535 1.500 1.625
1.500 1.500 7.000
1.535 1.500 1.625
1.500 1.500 7.000
1.535 1.500 1.625
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1
2
1
2
1
2
1
2
1
2
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
7.000
7.236
7.000
7.236
7.000
7.236
7.000
7.236
7.000
7.236
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
Cutting Mode
F1
1.535 1.250 1.375
6.000
6.236
6.000
6.236
6.000
6.236
6.000
6.236
6.000
6.236
GY06013M
TS55
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Insert
Fig.
1.250 1.250 6.000
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
Wrench
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
Page
GROOVING
Dimensions (inch)
(5 pcs.)
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
F012
F013
(Gauge insert)
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS

towards the center.
diameter.
F057
GROOVING SYSTEM

3-1
Note 2) Please use left hand modular blade for left hand modular holder.

GS
Fig. 1
Fig. 2
GROOVING
Left hand tool holder shown.
Seat
Size
Insert
Width
W3
(inch)
.118
.125
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
Order Number
ID
Modular Blade
Stock
1.378
1.575
.472
(4F1L4F11)
GYM25LD-F12-035
1.575
1.969
.472
(4F1L4F12) GYM25LD-F12-040
1.969
2.362
.472
(4F1L4F13) GYM25LD-F12-050
2.362
2.953
3.937
3.937
5.906
5.315
7.874
7.087
9.843
GYM25LD-F12-060
GYM25LD-F20-060
GYM25LD-F12-075
GYM25LD-F20-075
GYM25LD-F12-100
GYM25LD-F20-100
GYM25LD-F12-135
GYM25LD-F20-135
GYM25LD-F12-180
GYM25LD-F20-180
2.953
(4F1L4F14)
(4F1L4F24)
(4F1L4F15)
(4F1L4F25)
(4F1L4F16)
(4F1L4F26)
(4F1L4F17)
(4F1L4F27)
(4F1L4F18)
(4F1L4F28)
1.378
1.575
.472
(4H1L4F11) GYM25LD-F12-035
1.575
1.969
.472
(4H1L4F12) GYM25LD-F12-040
1.969
2.362
.472
(4H1L4F13) GYM25LD-F12-050
2.362
2.953
3.937
3.937
5.906
5.315
7.874
7.087
9.843
(4H1L4F14) GYM25LD-F12-060
1 (4H1L4F24) GYM25LD-F20-060
(4H1L4F15) GYM25LD-F12-075
1 (4H1L4F25) GYM25LD-F20-075
(4H1L4F16) GYM25LD-F12-100
1 (4H1L4F26) GYM25LD-F20-100
(4H1L4F17) GYM25LD-F12-135
1 (4H1L4F27) GYM25LD-F20-135
(4H1L4F18) GYM25LD-F12-180
1 (4H1L4F28) GYM25LD-F20-180
2.953
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
*
*1
*1
*1
*1
*
*
*
*
*
a
a
Modular Holder
Stock
GYHLUS12C00-M25L
GYHLUS16D00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
F054 for right hand tools.
*

F058
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
Fig. 4
GYHLUS12C00-M25L
GYHLUS16D00-M25L
Dimensions (inch)
H1
L1
L2
H2
*2
F1
.750 1.000 .250
.750
.750 5.000 1.535
.750 1.000 .250
.750
.750 5.000 1.535
.750 1.000 .250
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
3
4
3
4
3
4
3
4
3
4
1.000 1.000 6.000 1.535 1.000 1.125
1.000 1.000 6.000 1.535 1.000 1.125
1.000 1.000 6.000 1.535 1.000 1.125
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000

1
2
1
2
1
2
1
2
1
2
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.236
6.000
6.236
6.000
6.236
6.000
6.236
6.000
6.236
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Cutting Mode
S3
.750 5.000 1.535
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
Wrench
Insert
Fig.
.750
5.000
5.236
5.000
5.236
5.000
5.236
5.000
5.236
5.000
5.236
(5 pcs.)
Page
GROOVING
Fig. 3
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
F012
F013
(Gauge insert)
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS

towards the center.
diameter.
F059
GROOVING SYSTEM

3-1

GS
Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.118
.125
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
Order Number
ID
Modular Blade
Stock
1.378
1.575
.472
(4K1L4F11) GYM25LD-F12-035
1.575
1.969
.472
(4K1L4F12) GYM25LD-F12-040
1.969
2.362
.472
(4K1L4F13) GYM25LD-F12-050
2.362
2.953
3.937
3.937
5.906
5.315
7.874
7.087
9.843
GYM25LD-F12-060
GYM25LD-F20-060
GYM25LD-F12-075
GYM25LD-F20-075
GYM25LD-F12-100
GYM25LD-F20-100
GYM25LD-F12-135
GYM25LD-F20-135
GYM25LD-F12-180
GYM25LD-F20-180
2.953
(4K1L4F14)
(4K1L4F24)
(4K1L4F15)
(4K1L4F25)
(4K1L4F16)
(4K1L4F26)
(4K1L4F17)
(4K1L4F27)
(4K1L4F18)
(4K1L4F28)
1.378
1.575
.472
(4M1L4F11) GYM25LD-F12-035
1.575
1.969
.472
(4M1L4F12) GYM25LD-F12-040
1.969
2.362
.472
(4M1L4F13) GYM25LD-F12-050
2.362
2.953
3.937
3.937
5.906
5.315
7.874
7.087
9.843
(4M1L4F14) GYM25LD-F12-060
1 (4M1L4F24) GYM25LD-F20-060
(4M1L4F15) GYM25LD-F12-075
1 (4M1L4F25) GYM25LD-F20-075
(4M1L4F16) GYM25LD-F12-100
1 (4M1L4F26) GYM25LD-F20-100
(4M1L4F17) GYM25LD-F12-135
1 (4M1L4F27) GYM25LD-F20-135
(4M1L4F18) GYM25LD-F12-180
1 (4M1L4F28) GYM25LD-F20-180
2.953
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
*
*1
*1
*1
*1
*
*
*
*
*
a
a
Modular Holder
Stock
GYHLUS20D00-M25L
GYHLUS24E00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F060
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHLUS20D00-M25L
GYHLUS24E00-M25L
H1
L1
L2
*2
H2
1.250 1.250 6.000 1.535 1.250 1.375
1.250 1.250 6.000 1.535 1.250 1.375
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1
2
1
2
1
2
1
2
1
2
1.500 1.500 7.000 1.535 1.500 1.625
1.500 1.500 7.000 1.535 1.500 1.625
1.500 1.500 7.000 1.535 1.500 1.625
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1
2
1
2
1
2
1
2
1
2
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
7.000
7.236
7.000
7.236
7.000
7.236
7.000
7.236
7.000
7.236
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.535
1.772
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
Cutting Mode
F1
1
6.000
6.236
6.000
6.236
6.000
6.236
6.000
6.236
6.000
6.236
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Insert
Fig.
1.250 1.250 6.000 1.535 1.250 1.375
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
Wrench
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
Page
GROOVING
Dimensions (inch)
(5 pcs.)
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
F012
F013
(Gauge insert)
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS

towards the center.
diameter.
F061
GROOVING SYSTEM

3-1

GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.157
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
Order Number
ID
Modular Blade
Stock
1.575
1.969
.551
(4F1R4G11) GYM25RD-G14-040
1.969
2.362
.551
(4F1R4G12) GYM25RD-G14-050
2.362
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
(4F1R4G13) GYM25RD-G14-060
1 (4F1R4G23) GYM25RD-G25-060
(4F1R4G14) GYM25RD-G14-085
1 (4F1R4G24) GYM25RD-G25-085
(4F1R4G15) GYM25RD-G14-125
1 (4F1R4G25) GYM25RD-G25-125
(4F1R4G16) GYM25RD-G14-180
1 (4F1R4G26) GYM25RD-G25-180
(4F1R4G17) GYM25RD-G14-250
1 (4F1R4G27) GYM25RD-G25-250
3.346
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
1.575
1.969
.551
(4H1R4G11) GYM25RD-G14-040
1.969
2.362
.551
(4H1R4G12) GYM25RD-G14-050
2.362
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
(4H1R4G13) GYM25RD-G14-060
1 (4H1R4G23) GYM25RD-G25-060
(4H1R4G14) GYM25RD-G14-085
1 (4H1R4G24) GYM25RD-G25-085
(4H1R4G15) GYM25RD-G14-125
1 (4H1R4G25) GYM25RD-G25-125
(4H1R4G16) GYM25RD-G14-180
1 (4H1R4G26) GYM25RD-G25-180
(4H1R4G17) GYM25RD-G14-250
1 (4H1R4G27) GYM25RD-G25-250
3.346
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHRUS12C00-M25R
GYHRUS16D00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F062
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
Fig. 4
GYGRUS12C00-M25R
GYGRUS16D00-M25R
Dimensions (inch)
H1
L1
L2
H2
*2
F1
.750 1.000 .250
.750
.750 5.000 1.535
.750 1.000 .250
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
3
4
3
4
3
4
3
4
3
4
1.000 1.000 6.000 1.535 1.000 1.125
1.000 1.000 6.000 1.535 1.000 1.125
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000

1
2
1
2
1
2
1
2
1
2
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Cutting Mode
S3
.750 5.000 1.535
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
Wrench
Insert
Fig.
.750
5.000
5.433
5.000
5.433
5.000
5.433
5.000
5.433
5.000
5.433
(5 pcs.)
Page
GROOVING
Fig. 3
GY2M0400G030N-GU
GY2M0400G020N-GS
GY2M0400G030N-GM
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
(Gauge insert)
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS

towards the center.
diameter.
F063
GROOVING SYSTEM

3-1

GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.157
Hand
(R/L)
*3
Max.
First Cut Diameter
Groove Depth
D1 (inch)
ar
(inch)
Min.
Max.
Order Number
ID
Modular Blade
Stock
1.575
1.969
.551
(4K1R4G11) GYM25RD-G14-040
1.969
2.362
.551
(4K1R4G12) GYM25RD-G14-050
2.362
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
(4K1R4G13) GYM25RD-G14-060
1 (4K1R4G23) GYM25RD-G25-060
(4K1R4G14) GYM25RD-G14-085
1 (4K1R4G24) GYM25RD-G25-085
(4K1R4G15) GYM25RD-G14-125
1 (4K1R4G25) GYM25RD-G25-125
(4K1R4G16) GYM25RD-G14-180
1 (4K1R4G26) GYM25RD-G25-180
(4K1R4G17) GYM25RD-G14-250
1 (4K1R4G27) GYM25RD-G25-250
3.346
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
1.575
1.969
.551
(4M1R4G11) GYM25RD-G14-040
1.969
2.362
.551
(4M1R4G12) GYM25RD-G14-050
2.362
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
(4M1R4G13) GYM25RD-G14-060
1 (4M1R4G23) GYM25RD-G25-060
(4M1R4G14) GYM25RD-G14-085
1 (4M1R4G24) GYM25RD-G25-085
(4M1R4G15) GYM25RD-G14-125
1 (4M1R4G25) GYM25RD-G25-125
(4M1R4G16) GYM25RD-G14-180
1 (4M1R4G26) GYM25RD-G25-180
(4M1R4G17) GYM25RD-G14-250
1 (4M1R4G27) GYM25RD-G25-250
3.346
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHRUS20D00-M25R
GYHRUS24E00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F064
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHRUS20D00-M25R
GYHRUS24E00-M25R
H1
L1
L2
*2
H2
1.250 1.250 6.000 1.535 1.250 1.375
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1
2
1
2
1
2
1
2
1
2
1.500 1.500 7.000 1.535 1.500 1.625
1.500 1.500 7.000 1.535 1.500 1.625
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1
2
1
2
1
2
1
2
1
2
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
7.000
7.433
7.000
7.433
7.000
7.433
7.000
7.433
7.000
7.433
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
Cutting Mode
F1
1
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Insert
Fig.
1.250 1.250 6.000 1.535 1.250 1.375
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
Wrench
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
Page
GROOVING
Dimensions (inch)
(5 pcs.)
GY2M0400G030N-GU
GY2M0400G020N-GS
GY2M0400G030N-GM
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
(Gauge insert)
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS

towards the center.
diameter.
F065
GROOVING SYSTEM

3-1

GS
Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.157
Hand
(R/L)
*3
Max.
First Cut Diameter
Groove Depth
D1 (inch)
ar
(inch)
Min.
Max.
Order Number
ID
Modular Blade
Stock
1.575
1.969
.551
(4F1L4G11) GYM25LD-G14-040
1.969
2.362
.551
(4F1L4G12) GYM25LD-G14-050
2.362
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
(4F1L4G13) GYM25LD-G14-060
1 (4F1L4G23) GYM25LD-G25-060
(4F1L4G14) GYM25LD-G14-085
1 (4F1L4G24) GYM25LD-G25-085
(4F1L4G15) GYM25LD-G14-125
1 (4F1L4G25) GYM25LD-G25-125
(4F1L4G16) GYM25LD-G14-180
1 (4F1L4G26) GYM25LD-G25-180
(4F1L4G17) GYM25LD-G14-250
1 (4F1L4G27) GYM25LD-G25-250
3.346
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
1.575
1.969
.551
(4H1L4G11) GYM25LD-G14-040
1.969
2.362
.551
(4H1L4G12) GYM25LD-G14-050
2.362
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
(4H1L4G13) GYM25LD-G14-060
1 (4H1L4G23) GYM25LD-G25-060
(4H1L4G14) GYM25LD-G14-085
1 (4H1L4G24) GYM25LD-G25-085
(4H1L4G15) GYM25LD-G14-125
1 (4H1L4G25) GYM25LD-G25-125
(4H1L4G16) GYM25LD-G14-180
1 (4H1L4G26) GYM25LD-G25-180
(4H1L4G17) GYM25LD-G14-250
1 (4H1L4G27) GYM25LD-G25-250
3.346
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHLUS12C00-M25L
GYHLUS16D00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F066
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
Fig. 4

GYHLUS12C00-M25L
GYHLUS16D00-M25L
Dimensions (inch)
H1
L1
L2
H2
*2
F1
.750 1.000 .250
.750
.750 5.000 1.535
.750 1.000 .250
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
3
4
3
4
3
4
3
4
3
4
1.000 1.000 6.000 1.535 1.000 1.125
1.000 1.000 6.000 1.535 1.000 1.125
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000

1
2
1
2
1
2
1
2
1
2
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Cutting Mode
S3
.750 5.000 1.535
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
Wrench
Insert
Fig.
.750
5.000
5.433
5.000
5.433
5.000
5.433
5.000
5.433
5.000
5.433
(5 pcs.)
Page
GROOVING
Fig. 3
GY2M0400G030N-GU
GY2M0400G020N-GS
GY2M0400G030N-GM
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
(Gauge insert)
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS

towards the center.
diameter.
F067
GROOVING SYSTEM

3-1

GS
Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.157
Hand
(R/L)
*3
Max.
First Cut Diameter
Groove Depth
D1 (inch)
ar
(inch)
Min.
Max.
Order Number
ID
Modular Blade
Stock
1.575
1.969
.551
(4K1L4G11) GYM25LD-G14-040
1.969
2.362
.551
(4K1L4G12) GYM25LD-G14-050
2.362
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
(4K1L4G13) GYM25LD-G14-060
1 (4K1L4G23) GYM25LD-G25-060
(4K1L4G14) GYM25LD-G14-085
1 (4K1L4G24) GYM25LD-G25-085
(4K1L4G15) GYM25LD-G14-125
1 (4K1L4G25) GYM25LD-G25-125
(4K1L4G16) GYM25LD-G14-180
1 (4K1L4G26) GYM25LD-G25-180
(4K1L4G17) GYM25LD-G14-250
1 (4K1L4G27) GYM25LD-G25-250
3.346
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
1.575
1.969
.551
(4M1L4G11) GYM25LD-G14-040
1.969
2.362
.551
(4M1L4G12) GYM25LD-G14-050
2.362
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
(4M1L4G13) GYM25LD-G14-060
1 (4M1L4G23) GYM25LD-G25-060
(4M1L4G14) GYM25LD-G14-085
1 (4M1L4G24) GYM25LD-G25-085
(4M1L4G15) GYM25LD-G14-125
1 (4M1L4G25) GYM25LD-G25-125
(4M1L4G16) GYM25LD-G14-180
1 (4M1L4G26) GYM25LD-G25-180
(4M1L4G17) GYM25LD-G14-250
1 (4M1L4G27) GYM25LD-G25-250
3.346
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHLUS20D00-M25L
GYHLUS24E00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F068
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHLUS20D00-M25L
GYHLUS24E00-M25L
H1
L1
L2
*2
H2

1
1.250 1.250
6.000 1.535 1.250 1.375
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1
2
1
2
1
2
1
2
1
2
1.500 1.500
7.000 1.535 1.500 1.625
1.500 1.500
7.000 1.535 1.500 1.625
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
7.000
7.433
7.000
7.433
7.000
7.433
7.000
7.433
7.000
7.433
1
2
1
2
1
2
1
2
1
2
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
Cutting Mode
F1
6.000 1.535 1.250 1.375
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Insert
Fig.
1.250 1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
Wrench
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
Page
GROOVING
Dimensions (inch)
(5 pcs.)
GY2M0400G030N-GU
GY2M0400G020N-GS
GY2M0400G030N-GM
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
(Gauge insert)
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS

towards the center.
diameter.
F069
GROOVING SYSTEM

3-1

GF
GS
GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.187
.197
Hand
(R/L)
3
R*
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
1.969
2.362
2.362
3.346
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
1.969
2.362
2.362
3.346
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
Order Number
ID
Modular Blade
Stock
.551
(4F1R4H11) GYM25RD-H14-050
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
(4F1R4H12) GYM25RD-H14-060
1 (4F1R4H22) GYM25RD-H25-060
(4F1R4H13) GYM25RD-H14-085
1 (4F1R4H23) GYM25RD-H25-085
(4F1R4H14) GYM25RD-H14-125
1 (4F1R4H24) GYM25RD-H25-125
(4F1R4H15) GYM25RD-H14-180
1 (4F1R4H25) GYM25RD-H25-180
(4F1R4H16) GYM25RD-H14-250
1 (4F1R4H26) GYM25RD-H25-250
.551
(4H1R4H11) GYM25RD-H14-050
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
(4H1R4H12) GYM25RD-H14-060
1 (4H1R4H22) GYM25RD-H25-060
(4H1R4H13) GYM25RD-H14-085
1 (4H1R4H23) GYM25RD-H25-085
(4H1R4H14) GYM25RD-H14-125
1 (4H1R4H24) GYM25RD-H25-125
(4H1R4H15) GYM25RD-H14-180
1 (4H1R4H25) GYM25RD-H25-180
(4H1R4H16) GYM25RD-H14-250
1 (4H1R4H26) GYM25RD-H25-250
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHRUS12C00-M25R
GYHRUS16D00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F070
&D1 (Min.)
&D1 (Max.)
FACE GROOVING

SPARE PARTS
Fig. 4
GYHRUS12C00-M25R
GYHRUS16D00-M25R
Dimensions (inch)
H1
L1
L2
H2
*2
F1
.750 1.000 .250
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
3
4
3
4
3
4
3
4
3
4
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
1.000 1.000 6.000 1.535 1.000 1.125
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000

1
2
1
2
1
2
1
2
1
2
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Cutting Mode
S3
.750 5.000 1.535

1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
Wrench
Insert
Fig.
.750
5.000
5.433
5.000
5.433
5.000
5.433
5.000
5.433
5.000
5.433
(5 pcs.)
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Fig. 3
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
GY2M0500H040R05-GM
GY2M0500H040L05-GM
GY2M0500H040N-MS
GY2M0500H080N-MS
F012
F013
(Gauge insert)
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS

towards the center.
diameter.
F071
GROOVING SYSTEM

3-1

GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.187
.197
Hand
(R/L)
3
R*
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
1.969
2.362
2.362
3.346
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
1.969
2.362
2.362
3.346
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
Order Number
ID
Modular Blade
Stock
.551
(4K1R4H11) GYM25RD-H14-050
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
(4K1R4H12) GYM25RD-H14-060
1 (4K1R4H22) GYM25RD-H25-060
(4K1R4H13) GYM25RD-H14-085
1 (4K1R4H23) GYM25RD-H25-085
(4K1R4H14) GYM25RD-H14-125
1 (4K1R4H24) GYM25RD-H25-125
(4K1R4H15) GYM25RD-H14-180
1 (4K1R4H25) GYM25RD-H25-180
(4K1R4H16) GYM25RD-H14-250
1 (4K1R4H26) GYM25RD-H25-250
.551
(4M1R4H11) GYM25RD-H14-050
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
(4M1R4H12) GYM25RD-H14-060
1 (4M1R4H22) GYM25RD-H25-060
(4M1R4H13) GYM25RD-H14-085
1 (4M1R4H23) GYM25RD-H25-085
(4M1R4H14) GYM25RD-H14-125
1 (4M1R4H24) GYM25RD-H25-125
(4M1R4H15) GYM25RD-H14-180
1 (4M1R4H25) GYM25RD-H25-180
(4M1R4H16) GYM25RD-H14-250
1 (4M1R4H26) GYM25RD-H25-250
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHRUS20D00-M25R
GYHRUS24E00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F072
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHRUS20D00-M25R
GYHRUS24E00-M25R
H1
L1
L2
*2
H2
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1
2
1
2
1
2
1
2
1
2
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.500 1.500 7.000 1.535 1.500 1.625
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1
2
1
2
1
2
1
2
1
2
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
7.000
7.433
7.000
7.433
7.000
7.433
7.000
7.433
7.000
7.433
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
Cutting Mode
F1
1
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Insert
Fig.
1.250 1.250 6.000 1.535 1.250 1.375

1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
Wrench
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Dimensions (inch)
(5 pcs.)
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
GY2M0500H040R05-GM
GY2M0500H040L05-GM
GY2M0500H040N-MS
GY2M0500H080N-MS
F012
F013
(Gauge insert)
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS

towards the center.
diameter.
F073
GROOVING SYSTEM

3-1

GS
Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.187
.197
Hand
(R/L)
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
1.969
2.362
2.362
3.346
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
1.969
2.362
2.362
3.346
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
Order Number
ID
Modular Blade
Stock
.551
(4F1L4H11) GYM25LD-H14-050
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
(4F1L4H12) GYM25LD-H14-060
1 (4F1L4H22) GYM25LD-H25-060
(4F1L4H13) GYM25LD-H14-085
1 (4F1L4H23) GYM25LD-H25-085
(4F1L4H14) GYM25LD-H14-125
1 (4F1L4H24) GYM25LD-H25-125
(4F1L4H15) GYM25LD-H14-180
1 (4F1L4H25) GYM25LD-H25-180
(4F1L4H16) GYM25LD-H14-250
1 (4F1L4H26) GYM25LD-H25-250
.551
(4H1L4H11) GYM25LD-H14-050
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
(4H1L4H12) GYM25LD-H14-060
1 (4H1L4H22) GYM25LD-H25-060
(4H1L4H13) GYM25LD-H14-085
1 (4H1L4H23) GYM25LD-H25-085
(4H1L4H14) GYM25LD-H14-125
1 (4H1L4H24) GYM25LD-H25-125
(4H1L4H15) GYM25LD-H14-180
1 (4H1L4H25) GYM25LD-H25-180
(4H1L4H16) GYM25LD-H14-250
1 (4H1L4H26) GYM25LD-H25-250
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHLUS12C00-M25L
GYHLUS16D00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F074
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
Fig. 4

GYHLUS12C00-M25L
GYHLUS16D00-M25L
Dimensions (inch)
H1
L1
L2
H2
*2
F1
.750 1.000 .250
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
3
4
3
4
3
4
3
4
3
4
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
1.000 1.000 6.000 1.535 1.000 1.125
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000

1
2
1
2
1
2
1
2
1
2
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Cutting Mode
S3
.750 5.000 1.535

1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
Wrench
Insert
Fig.
.750
5.000
5.433
5.000
5.433
5.000
5.433
5.000
5.433
5.000
5.433
(5 pcs.)
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Fig. 3
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
GY2M0500H040R05-GM
GY2M0500H040L05-GM
GY2M0500H040N-MS
GY2M0500H080N-MS
F012
F013
(Gauge insert)
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS

towards the center.
diameter.
F075
GROOVING SYSTEM

3-1

GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.187
.197
Hand
(R/L)
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
1.969
2.362
2.362
3.346
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
1.969
2.362
2.362
3.346
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
Order Number
ID
Modular Blade
Stock
.551
(4K1L4H11) GYM25LD-H14-050
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
(4K1L4H12) GYM25LD-H14-060
1 (4K1L4H22) GYM25LD-H25-060
(4K1L4H13) GYM25LD-H14-085
1 (4K1L4H23) GYM25LD-H25-085
(4K1L4H14) GYM25LD-H14-125
1 (4K1L4H24) GYM25LD-H25-125
(4K1L4H15) GYM25LD-H14-180
1 (4K1L4H25) GYM25LD-H25-180
(4K1L4H16) GYM25LD-H14-250
1 (4K1L4H26) GYM25LD-H25-250
.551
(4M1L4H11) GYM25LD-H14-050
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
(4M1L4H12) GYM25LD-H14-060
1 (4M1L4H22) GYM25LD-H25-060
(4M1L4H13) GYM25LD-H14-085
1 (4M1L4H23) GYM25LD-H25-085
(4M1L4H14) GYM25LD-H14-125
1 (4M1L4H24) GYM25LD-H25-125
(4M1L4H15) GYM25LD-H14-180
1 (4M1L4H25) GYM25LD-H25-180
(4M1L4H16) GYM25LD-H14-250
1 (4M1L4H26) GYM25LD-H25-250
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHLUS20D00-M25L
GYHLUS24E00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F076
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHLUS20D00-M25L
GYHLUS24E00-M25L
H1
L1
L2
*2
H2

1
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
1
2
1
2
1
2
1
2
1
2
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.500 1.500
7.000 1.535 1.500 1.625
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
7.000
7.433
7.000
7.433
7.000
7.433
7.000
7.433
7.000
7.433
1
2
1
2
1
2
1
2
1
2
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
Cutting Mode
F1
6.000 1.535 1.250 1.375

1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Insert
Fig.
1.250 1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
Wrench
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Dimensions (inch)
(5 pcs.)
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
GY2M0500H040R05-GM
GY2M0500H040L05-GM
GY2M0500H040N-MS
GY2M0500H080N-MS
F012
F013
(Gauge insert)
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS

towards the center.
diameter.
F077
GROOVING SYSTEM

3-1

L2
Fig. 1
H1
H2
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.236
.250
Hand
(R/L)
Max.
First Cut Diameter
Groove Depth
D1 (inch)
ar
(inch)
Min.
Max.
1.969
2.756
2.756
4.331
4.331
7.874
6.693
11.024
9.843
39.331
1.969
2.756
2.756
4.331
4.331
7.874
6.693
11.024
9.843
39.331
1.969
2.756
2.756
4.331
4.331
7.874
6.693
11.024
9.843
39.331
1.969
2.756
2.756
4.331
4.331
7.874
6.693
11.024
9.843
39.331
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
*
*1
*1
*1
1
*
*1
*1
*1
1
*
*1
*1
*1
1
*
*1
*1
*1
Order Number
ID
(4F1R4J11)
(4F1R4J12)
(4F1R4J22)
(4F1R4J13)
(4F1R4J23)
(4F1R4J14)
(4F1R4J24)
(4F1R4J15)
(4F1R4J25)
(4H1R4J11)
(4H1R4J12)
(4H1R4J22)
(4H1R4J13)
(4H1R4J23)
(4H1R4J14)
(4H1R4J24)
(4H1R4J15)
(4H1R4J25)
(4K1R4J11)
(4K1R4J12)
(4K1R4J22)
(4K1R4J13)
(4K1R4J23)
(4K1R4J14)
(4K1R4J24)
(4K1R4J15)
(4K1R4J25)
(4M1R4J11)
(4M1R4J12)
(4M1R4J22)
(4M1R4J13)
(4M1R4J23)
(4M1R4J14)
(4M1R4J24)
(4M1R4J15)
(4M1R4J25)
Modular Blade
Stock
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
GYM25RD-J25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
GYM25RD-J25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
GYM25RD-J25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
GYM25RD-J25-250
Modular Holder
Stock
GYHRUS12C00-M25R
GYHRUS16D00-M25R
GYHRUS20D00-M25R
GYHRUS24E00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*
F078
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
(5 pcs.)

Fig. 3
Fig. 4
x
Wrench
GYHRUS12C00-M25R
GYHRUS16D00-M25R
GYHRUS20D00-M25R
TS55
GY06013M
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
GYHRUS24E00-M25R
*2
Insert
Fig.
H1
L1
L2
H2
F1
S3
.750
.750
.750
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
.750
.750
.750
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
5.000
5.000
5.433
5.000
5.433
5.000
5.433
5.000
5.433
6.000
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
7.000
7.000
7.433
7.000
7.433
7.000
7.433
7.000
7.433
1.535
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
.750
.750
.750
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
.250
.250
.250
.250
.250
.250
.250
.250
.250

Cutting Mode
3
3
4
3
4
3
4
3
4
1
1
2
1
2
1
2
1
2
1
1
2
1
2
1
2
1
2
1
1
2
1
2
1
2
1
2
Page
GROOVING
Dimensions (inch)
GY2M0600J040N-GU
GY2M0635J040N-GU
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
GY2M0635J040N-GM
GY2M0600J040N-MS
GY2M0600J080N-MS
F012
F013
(Gauge insert)
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM

towards the center.
diameter.
F079
GROOVING SYSTEM

3-1

Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
.236
.250
Hand
(R/L)
Max.
First Cut Diameter
Groove Depth
D1 (inch)
ar
(inch)
Min.
Max.
1.969
2.756
2.756
4.331
4.331
7.874
6.693
11.024
9.843
39.331
1.969
2.756
2.756
4.331
4.331
7.874
6.693
11.024
9.843
39.331
1.969
2.756
2.756
4.331
4.331
7.874
6.693
11.024
9.843
39.331
1.969
2.756
2.756
4.331
4.331
7.874
6.693
11.024
9.843
39.331
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
*
*1
*1
*1
1
*
*1
*1
*1
1
*
*1
*1
*1
1
*
*1
*1
*1
Order Number
ID
(4F1L4J11)
(4F1L4J12)
(4F1L4J22)
(4F1L4J13)
(4F1L4J23)
(4F1L4J14)
(4F1L4J24)
(4F1L4J15)
(4F1L4J25)
(4H1L4J11)
(4H1L4J12)
(4H1L4J22)
(4H1L4J13)
(4H1L4J23)
(4H1L4J14)
(4H1L4J24)
(4H1L4J15)
(4H1L4J25)
(4K1L4J11)
(4K1L4J12)
(4K1L4J22)
(4K1L4J13)
(4K1L4J23)
(4K1L4J14)
(4K1L4J24)
(4K1L4J15)
(4K1L4J25)
(4M1L4J11)
(4M1L4J12)
(4M1L4J22)
(4M1L4J13)
(4M1L4J23)
(4M1L4J14)
(4M1L4J24)
(4M1L4J15)
(4M1L4J25)
Modular Blade
Stock
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
GYM25LD-J25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
GYM25LD-J25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
GYM25LD-J25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
GYM25LD-J25-250
Modular Holder
Stock
GYHLUS12C00-M25L
GYHLUS16D00-M25L
GYHLUS20D00-M25L
GYHLUS24E00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*
F080
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
(5 pcs.)

Fig. 4
Fig. 3
x
Wrench
GYHLUS12C00-M25L
GYHLUS16D00-M25L
GYHLUS20D00-M25L
TS55
GY06013M
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
GYHLUS24E00-M25L
*2
Insert
Fig.
H1
L1
L2
H2
F1
S3
.750
.750
.750
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
.750
.750
.750
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
5.000
5.000
5.433
5.000
5.433
5.000
5.433
5.000
5.433
6.000
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.000
6.433
6.000
6.433
6.000
6.433
6.000
6.433
7.000
7.000
7.433
7.000
7.433
7.000
7.433
7.000
7.433
1.535
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.535
1.969
1.535
1.969
1.535
1.969
1.535
1.969
.750
.750
.750
.750
.750
.750
.750
.750
.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.125
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
1.625
.250
.250
.250
.250
.250
.250
.250
.250
.250

Cutting Mode
3
3
4
3
4
3
4
3
4
1
1
2
1
2
1
2
1
2
1
1
2
1
2
1
2
1
2
1
1
2
1
2
1
2
1
2
Page
GROOVING
Dimensions (inch)
GY2M0600J040N-GU
GY2M0635J040N-GU
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
GY2M0635J040N-GM
GY2M0600J040N-MS
GY2M0600J080N-MS
F012
F013
(Gauge insert)
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM
Notes when selecting a modular blade ((2)

2)
towards the center.
diameter.
F081
GROOVING SYSTEM

4-1
GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Hand
(R/L)
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
.118
.125
Modular Blade
Stock
1.378
1.575
.472
(5H1R4F11) GYM25LD-F12-035
1.575
1.969
.472
(5H1R4F12) GYM25LD-F12-040
1.969
2.362
.472
(5H1R4F13) GYM25LD-F12-050
2.362
2.953
3.937
3.937
5.906
5.315
7.874
7.087
9.843
(5H1R4F14) GYM25LD-F12-060
1 (5H1R4F24) GYM25LD-F20-060
(5H1R4F15) GYM25LD-F12-075
1 (5H1R4F25) GYM25LD-F20-075
(5H1R4F16) GYM25LD-F12-100
1 (5H1R4F26) GYM25LD-F20-100
(5H1R4F17) GYM25LD-F12-135
1 (5H1R4F27) GYM25LD-F20-135
(5H1R4F18) GYM25LD-F12-180
1 (5H1R4F28) GYM25LD-F20-180
2.953
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
1.378
1.575
.472
(5H1L4F11) GYM25RD-F12-035
1.575
1.969
.472
(5H1L4F12) GYM25RD-F12-040
1.969
2.362
.472
(5H1L4F13) GYM25RD-F12-050
2.362
2.953
3.937
3.937
5.906
5.315
7.874
7.087
9.843
(5H1L4F14) GYM25RD-F12-060
1 (5H1L4F24) GYM25RD-F20-060
(5H1L4F15) GYM25RD-F12-075
1 (5H1L4F25) GYM25RD-F20-075
(5H1L4F16) GYM25RD-F12-100
1 (5H1L4F26) GYM25RD-F20-100
(5H1L4F17) GYM25RD-F12-135
1 (5H1L4F27) GYM25RD-F20-135
(5H1L4F18) GYM25RD-F12-180
1 (5H1L4F28) GYM25RD-F20-180
2.953
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
Order Number
ID
*
*
*
*
*
*
*
*
*
*
a
a
Modular Holder
Stock
GYHRUS16D90-M25L
GYHLUS16D90-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
shown are when the gauge insert is used. If other insert geometries are used then L1, L2, F1 and D1 values may vary.
*

F082
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHRUS16D90-M25L
GYHLUS16D90-M25R
H1
L1
L2
*2
H2

1
1.000 1.000 6.000 1.500
1.000 2.094
1.000 1.000 6.000 1.500
1.000 2.094
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1
2
1
2
1
2
1
2
1
2
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
2.094
2.330
2.094
2.330
2.094
2.330
2.094
2.330
2.094
2.330
1.000 1.000 6.000 1.500
1.000 2.094
1.000 1.000 6.000 1.500
1.000 2.094
1.000 1.000 6.000 1.500
1.000 2.094
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1
2
1
2
1
2
1
2
1
2
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
Cutting Mode
F1
1.000 2.094
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
TS55
GY06013M
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
1.000 1.000 6.000 1.500
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
Wrench
2.094
2.330
2.094
2.330
2.094
2.330
2.094
2.330
2.094
2.330
Page
GROOVING
Dimensions (inch)
(5 pcs.)
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
(Gauge insert)
F012
F013
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS

towards the center.
diameter.
F083
GROOVING SYSTEM

4-1
GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Hand
(R/L)
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
Modular Blade
Stock
1.575
1.969
.551
(5H1R4G11) GYM25LD-G14-040
1.969
2.362
.551
(5H1R4G12) GYM25LD-G14-050
2.362
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
(5H1R4G13) GYM25LD-G14-060
1 (5H1R4G23) GYM25LD-G25-060
(5H1R4G14) GYM25LD-G14-085
1 (5H1R4G24) GYM25LD-G25-085
(5H1R4G15) GYM25LD-G14-125
1 (5H1R4G25) GYM25LD-G25-125
(5H1R4G16) GYM25LD-G14-180
1 (5H1R4G26) GYM25LD-G25-180
(5H1R4G17) GYM25LD-G14-250
1 (5H1R4G27) GYM25LD-G25-250
3.346
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
1.575
1.969
.551
(5H1L4G11) GYM25RD-G14-040
1.969
2.362
.551
(5H1L4G12) GYM25RD-G14-050
2.362
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
(5H1L4G13) GYM25RD-G14-060
1 (5H1L4G23) GYM25RD-G25-060
(5H1L4G14) GYM25RD-G14-085
1 (5H1L4G24) GYM25RD-G25-085
(5H1L4G15) GYM25RD-G14-125
1 (5H1L4G25) GYM25RD-G25-125
(5H1L4G16) GYM25RD-G14-180
1 (5H1L4G26) GYM25RD-G25-180
(5H1L4G17) GYM25RD-G14-250
1 (5H1L4G27) GYM25RD-G25-250
3.346
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.157
Order Number
ID
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHRUS16D90-M25L
GYHLUS16D90-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F084
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHRUS16D90-M25L
GYHLUS16D90-M25R
H1
L1
L2
*2
H2
1.000 1.000 6.000 1.500 1.000 2.094
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
2.094
2.527
2.094
2.527
2.094
2.527
2.094
2.527
2.094
2.527
1
2
1
2
1
2
1
2
1
2
1.000 1.000 6.000 1.500 1.000 2.094
1.000 1.000 6.000 1.500 1.000 2.094
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1
2
1
2
1
2
1
2
1
2
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
Cutting Mode
F1
1
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
TS55
GY06013M
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
1.000 1.000 6.000 1.500 1.000 2.094
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
Wrench
Page
GY2M0400G030N-GU
GROOVING
Dimensions (inch)
(5 pcs.)
GY2M0400G020N-GS
GY2M0400G030N-GM
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
(Gauge insert)
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
2.094
2.527
2.094
2.527
2.094
2.527
2.094
2.527
2.094
2.527
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS

towards the center.
diameter.
F085
GROOVING SYSTEM

4-1
GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Hand
(R/L)
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
1.969
2.362
2.362
3.346
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
1.969
2.362
2.362
3.346
.187
.197
3.346
4.921
4.921
7.874
7.087
11.024
9.843
39.331
Order Number
ID
Modular Blade
Stock
.551
(5H1R4H11) GYM25LD-H14-050
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
(5H1R4H12) GYM25LD-H14-060
1 (5H1R4H22) GYM25LD-H25-060
(5H1R4H13) GYM25LD-H14-085
1 (5H1R4H23) GYM25LD-H25-085
(5H1R4H14) GYM25LD-H14-125
1 (5H1R4H24) GYM25LD-H25-125
(5H1R4H15) GYM25LD-H14-180
1 (5H1R4H25) GYM25LD-H25-180
(5H1R4H16) GYM25LD-H14-250
1 (5H1R4H26) GYM25LD-H25-250
.551
(5H1L4H11) GYM25RD-H14-050
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
(5H1L4H12) GYM25RD-H14-060
1 (5H1L4H22) GYM25RD-H25-060
(5H1L4H13) GYM25RD-H14-085
1 (5H1L4H23) GYM25RD-H25-085
(5H1L4H14) GYM25RD-H14-125
1 (5H1L4H24) GYM25RD-H25-125
(5H1L4H15) GYM25RD-H14-180
1 (5H1L4H25) GYM25RD-H25-180
(5H1L4H16) GYM25RD-H14-250
1 (5H1L4H26) GYM25RD-H25-250
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHRUS16D90-M25L
GYHLUS16D90-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F086
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHRUS16D90-M25L
GYHLUS16D90-M25R
H1
L1
L2
*2
H2

1
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
2.094
2.527
2.094
2.527
2.094
2.527
2.094
2.527
2.094
2.527
1
2
1
2
1
2
1
2
1
2
1.000 1.000
6.000 1.500 1.000 2.094
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
1
2
1
2
1
2
1
2
1
2
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
Cutting Mode
F1
6.000 1.500 1.000 2.094

1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
TS55
GY06013M
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
1.000 1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
Wrench
2.094
2.527
2.094
2.527
2.094
2.527
2.094
2.527
2.094
2.527
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Dimensions (inch)
(5 pcs.)
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
GY2M0500H040R05-GM
GY2M0500H040L05-GM F012
F013
GY2M0500H040N-MS
GY2M0500H080N-MS
(Gauge insert)
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS

towards the center.
diameter.
F087
GROOVING SYSTEM

4-1

GF
GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(inch)
Hand
(R/L)
.236
.250
First Cut Diameter

Max.
D1 (inch)
Groove Depth
ar
Min.
Max.
(inch)
1.969
2.756
2.756
4.331
4.331
7.874
6.693
11.024
9.843
39.331
1.969
2.756
2.756
4.331
4.331
7.874
6.693
11.024
9.843
39.331
Order Number
ID
Modular Blade
Stock
.551
(5H1R4J11) GYM25LD-J14-050
.551
.984
.551
.984
.551
.984
.551
.984
(5H1R4J12) GYM25LD-J14-070
1 (5H1R4J22) GYM25LD-J25-070
(5H1R4J13) GYM25LD-J14-110
1 (5H1R4J23) GYM25LD-J25-110
(5H1R4J14) GYM25LD-J14-170
1 (5H1R4J24) GYM25LD-J25-170
(5H1R4J15) GYM25LD-J14-250
1 (5H1R4J25) GYM25LD-J25-250
.551
(5H1L4J11) GYM25RD-J14-050
.551
.984
.551
.984
.551
.984
.551
.984
(5H1L4J12) GYM25RD-J14-070
1 (5H1L4J22) GYM25RD-J25-070
(5H1L4J13) GYM25RD-J14-110
1 (5H1L4J23) GYM25RD-J25-110
(5H1L4J14) GYM25RD-J14-170
1 (5H1L4J24) GYM25RD-J25-170
(5H1L4J15) GYM25RD-J14-250
1 (5H1L4J25) GYM25RD-J25-250
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHRUS16D90-M25L
GYHLUS16D90-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F088
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
(5 pcs.)
GYHRUS16D90-M25L
GYHLUS16D90-M25R
H1
L1
L2
*2
H2
Insert
Fig.
6.000 1.500 1.000 2.094
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
1
2
1
2
1
2
1
2
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
2.094
2.527
2.094
2.527
2.094
2.527
2.094
2.527
1.000 1.000
6.000 1.500 1.000 2.094
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
1
2
1
2
1
2
1
2
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
Cutting Mode
F1
1.000 1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
TS55
GY06013M
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
2.094
2.527
2.094
2.527
2.094
2.527
2.094
2.527
Page
GY2M0600J040N-GU
GY2M0635J040N-GU
GROOVING
Dimensions (inch)
x
Wrench
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
GY2M0635J040N-GM
GY2M0600J040N-MS
GY2M0600J080N-MS
F012
F013
(Gauge insert)
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM

towards the center.
diameter.
F089
GROOVING SYSTEM

3-2
00 type holder (Metric) NEW

GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
3.00
3.18
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
Order Number
ID
Modular Blade
Stock
35
40
12
(4E1R4F11) GYM25RD-F12-035
40
50
12
(4E1R4F12) GYM25RD-F12-040
50
60
12
(4E1R4F13) GYM25RD-F12-050
60
75
100
100
150
135
200
180
250
(4E1R4F14) GYM25RD-F12-060
1 (4E1R4F24) GYM25RD-F20-060
(4E1R4F15) GYM25RD-F12-075
1 (4E1R4F25) GYM25RD-F20-075
(4E1R4F16) GYM25RD-F12-100
1 (4E1R4F26) GYM25RD-F20-100
(4E1R4F17) GYM25RD-F12-135
1 (4E1R4F27) GYM25RD-F20-135
(4E1R4F18) GYM25RD-F12-180
1 (4E1R4F28) GYM25RD-F20-180
75
12
20
12
20
12
20
12
20
12
20
35
40
12
(4G1R4F11) GYM25RD-F12-035
40
50
12
(4G1R4F12) GYM25RD-F12-040
50
60
12
(4G1R4F13) GYM25RD-F12-050
60
75
100
100
150
135
200
180
250
(4G1R4F14) GYM25RD-F12-060
1 (4G1R4F24) GYM25RD-F20-060
(4G1R4F15) GYM25RD-F12-075
1 (4G1R4F25) GYM25RD-F20-075
(4G1R4F16) GYM25RD-F12-100
1 (4G1R4F26) GYM25RD-F20-100
(4G1R4F17) GYM25RD-F12-135
1 (4G1R4F27) GYM25RD-F20-135
(4G1R4F18) GYM25RD-F12-180
1 (4G1R4F28) GYM25RD-F20-180
75
12
20
12
20
12
20
12
20
12
20
*
*
*
*
*
*
*
*
*
*
a
a
Modular Holder
Stock
GYHR2020K00-M25R
GYHR2525M00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F090
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
Fig. 4
GYHR2020K00-M25R
GYHR2525M00-M25R
Dimensions (mm)
*2
(5 pcs.)
Wrench
TS55
GY06013M
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
S3
20
20
125
39
20
26
20
20
125
39
20
26
20
20
125
39
20
26
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
125
131
125
131
125
131
125
131
125
131
39
45
39
45
39
45
39
45
39
45
20
20
20
20
20
20
20
20
20
20
26
26
26
26
26
26
26
26
26
26
5
5
5
5
5
5
5
5
5
5
3
4
3
4
3
4
3
4
3
4
Cutting Mode
25
25
150
39
25
28
25
25
150
39
25
28
25
25
150
39
25
28
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
156
150
156
150
156
150
156
150
156
39
45
39
45
39
45
39
45
39
45
25
25
25
25
25
25
25
25
25
25
28
28
28
28
28
28
28
28
28
28

1
2
1
2
1
2
1
2
1
2
Page
GROOVING
Fig. 3
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
(Gauge insert)
F012
F013
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS

towards the center.
diameter.
F091
GROOVING SYSTEM

3-2

GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
3.00
3.18
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
Order Number
ID
Modular Blade
Stock
35
40
12
(4Q1R4F11) GYM25RD-F12-035
40
50
12
(4Q1R4F12) GYM25RD-F12-040
50
60
12
(4Q1R4F13) GYM25RD-F12-050
60
75
100
100
150
135
200
180
250
(4Q1R4F14) GYM25RD-F12-060
1 (4Q1R4F24) GYM25RD-F20-060
(4Q1R4F15) GYM25RD-F12-075
1 (4Q1R4F25) GYM25RD-F20-075
(4Q1R4F16) GYM25RD-F12-100
1 (4Q1R4F26) GYM25RD-F20-100
(4Q1R4F17) GYM25RD-F12-135
1 (4Q1R4F27) GYM25RD-F20-135
(4Q1R4F18) GYM25RD-F12-180
1 (4Q1R4F28) GYM25RD-F20-180
75
12
20
12
20
12
20
12
20
12
20
35
40
12
(4J1R4F11) GYM25RD-F12-035
40
50
12
(4J1R4F12) GYM25RD-F12-040
50
60
12
(4J1R4F13) GYM25RD-F12-050
60
75
100
100
150
135
200
180
250
(4J1R4F14) GYM25RD-F12-060
1 (4J1R4F24) GYM25RD-F20-060
(4J1R4F15) GYM25RD-F12-075
1 (4J1R4F25) GYM25RD-F20-075
(4J1R4F16) GYM25RD-F12-100
1 (4J1R4F26) GYM25RD-F20-100
(4J1R4F17) GYM25RD-F12-135
1 (4J1R4F27) GYM25RD-F20-135
(4J1R4F18) GYM25RD-F12-180
1 (4J1R4F28) GYM25RD-F20-180
75
12
20
12
20
12
20
12
20
12
20
*
*
*
*
*
*
*
*
*
*
a
a
Modular Holder
Stock
GYHR3225P00-M25R
GYHR3232P00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
maximum groove depth varies according to the insert used. Please refer to the maximum groove depth of inserts on pages F012 and F013.
*12 The
Dimensions shown are when the gauge insert is used. If other insert geometries are used then L1, L2, F1 and D1 values may vary.
*3 Refer to page F096 for left hand tools.
*

F092
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHR3225P00-M25R
GYHR3232P00-M25R
*2
Wrench
GY06013M
TS55
zTKY30R
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
32
25
170
39
32
28
32
25
170
39
32
28
32
25
170
39
32
28
32
32
32
32
32
32
32
32
32
32
25
25
25
25
25
25
25
25
25
25
170
176
170
176
170
176
170
176
170
176
39
45
39
45
39
45
39
45
39
45
32
32
32
32
32
32
32
32
32
32
28
28
28
28
28
28
28
28
28
28
1
2
1
2
1
2
1
2
1
2
Cutting Mode
32
32
170
39
32
35
32
32
170
39
32
35
32
32
170
39
32
35
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
170
176
170
176
170
176
170
176
170
176
39
45
39
45
39
45
39
45
39
45
32
32
32
32
32
32
32
32
32
32
35
35
35
35
35
35
35
35
35
35
1
2
1
2
1
2
1
2
1
2
Page
GROOVING
Dimensions (mm)
(5 pcs.)
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
(Gauge insert)
F012
F013
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS

towards the center.
diameter.
F093
GROOVING SYSTEM

3-2

GS
Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(mm)
3.00
3.18
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
Order Number
ID
Modular Blade
Stock
35
40
12
(4E1L4F11) GYM25LD-F12-035
40
50
12
(4E1L4F12) GYM25LD-F12-040
50
60
12
(4E1L4F13) GYM25LD-F12-050
60
75
100
100
150
135
200
180
250
(4E1L4F14) GYM25LD-F12-060
1 (4E1L4F24) GYM25LD-F20-060
(4E1L4F15) GYM25LD-F12-075
1 (4E1L4F25) GYM25LD-F20-075
(4E1L4F16) GYM25LD-F12-100
1 (4E1L4F26) GYM25LD-F20-100
(4E1L4F17) GYM25LD-F12-135
1 (4E1L4F27) GYM25LD-F20-135
(4E1L4F18) GYM25LD-F12-180
1 (4E1L4F28) GYM25LD-F20-180
75
12
20
12
20
12
20
12
20
12
20
35
40
12
(4G1L4F11) GYM25LD-F12-035
40
50
12
(4G1L4F12) GYM25LD-F12-040
50
60
12
(4G1L4F13) GYM25LD-F12-050
60
75
100
100
150
135
200
180
250
(4G1L4F14) GYM25LD-F12-060
1 (4G1L4F24) GYM25LD-F20-060
(4G1L4F15) GYM25LD-F12-075
1 (4G1L4F25) GYM25LD-F20-075
(4G1L4F16) GYM25LD-F12-100
1 (4G1L4F26) GYM25LD-F20-100
(4G1L4F17) GYM25LD-F12-135
1 (4G1L4F27) GYM25LD-F20-135
(4G1L4F18) GYM25LD-F12-180
1 (4G1L4F28) GYM25LD-F20-180
75
12
20
12
20
12
20
12
20
12
20
*
*
*
*
*
*
*
*
*
*
a
a
Modular Holder
Stock
GYHL2020K00-M25L
GYHL2525M00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F094
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
Fig. 4

GYHL2020K00-M25L
GYHL2525M00-M25L
Dimensions (mm)
*2
(5 pcs.)
Wrench
GY06013M
TS55
zTKY30R
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
S3
20
20
125
39
20
26
20
20
125
39
20
26
20
20
125
39
20
26
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
125
131
125
131
125
131
125
131
125
131
39
45
39
45
39
45
39
45
39
45
20
20
20
20
20
20
20
20
20
20
26
26
26
26
26
26
26
26
26
26
5
5
5
5
5
5
5
5
5
5
3
4
3
4
3
4
3
4
3
4
Cutting Mode
25
25
150
39
25
28
25
25
150
39
25
28
25
25
150
39
25
28
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
156
150
156
150
156
150
156
150
156
39
45
39
45
39
45
39
45
39
45
25
25
25
25
25
25
25
25
25
25
28
28
28
28
28
28
28
28
28
28

1
2
1
2
1
2
1
2
1
2
Page
GROOVING
Fig. 3
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
(Gauge insert)
F012
F013
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS

towards the center.
diameter.
F095
GROOVING SYSTEM

3-2

GS
Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(mm)
3.00
3.18
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
Order Number
ID
Modular Blade
Stock
35
40
12
(4Q1L4F11) GYM25LD-F12-035
40
50
12
(4Q1L4F12) GYM25LD-F12-040
50
60
12
(4Q1L4F13) GYM25LD-F12-050
60
75
100
100
150
135
200
180
250
(4Q1L4F14) GYM25LD-F12-060
1 (4Q1L4F24) GYM25LD-F20-060
(4Q1L4F15) GYM25LD-F12-075
1 (4Q1L4F25) GYM25LD-F20-075
(4Q1L4F16) GYM25LD-F12-100
1 (4Q1L4F26) GYM25LD-F20-100
(4Q1L4F17) GYM25LD-F12-135
1 (4Q1L4F27) GYM25LD-F20-135
(4Q1L4F18) GYM25LD-F12-180
1 (4Q1L4F28) GYM25LD-F20-180
75
12
20
12
20
12
20
12
20
12
20
35
40
12
(4J1L4F11)
GYM25LD-F12-035
40
50
12
(4J1L4F12)
GYM25LD-F12-040
50
60
12
(4J1L4F13)
GYM25LD-F12-050
60
75
100
100
150
135
200
180
250
GYM25LD-F12-060
GYM25LD-F20-060
GYM25LD-F12-075
GYM25LD-F20-075
GYM25LD-F12-100
GYM25LD-F20-100
GYM25LD-F12-135
GYM25LD-F20-135
GYM25LD-F12-180
GYM25LD-F20-180
75
(4J1L4F14)
(4J1L4F24)
(4J1L4F15)
(4J1L4F25)
(4J1L4F16)
(4J1L4F26)
(4J1L4F17)
(4J1L4F27)
(4J1L4F18)
(4J1L4F28)
12
20
12
20
12
20
12
20
12
20
*
*
*
*
*
*1
*1
*1
*1
*1
a
a
Modular Holder
Stock
GYHL3225P00-M25L
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F096
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHL3225P00-M25L
GYHL3232P00-M25L
*2
Wrench
GY06013M
TS55
zTKY30R
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
32
25
170
39
32
28
32
25
170
39
32
28
32
25
170
39
32
28
32
32
32
32
32
32
32
32
32
32
25
25
25
25
25
25
25
25
25
25
170
176
170
176
170
176
170
176
170
176
39
45
39
45
39
45
39
45
39
45
32
32
32
32
32
32
32
32
32
32
28
28
28
28
28
28
28
28
28
28
1
2
1
2
1
2
1
2
1
2
Cutting Mode
32
32
170
39
32
35
32
32
170
39
32
35
32
32
170
39
32
35
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
170
176
170
176
170
176
170
176
170
176
39
45
39
45
39
45
39
45
39
45
32
32
32
32
32
32
32
32
32
32
35
35
35
35
35
35
35
35
35
35
1
2
1
2
1
2
1
2
1
2
Page
GROOVING
Dimensions (mm)
(5 pcs.)
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
(Gauge insert)
F012
F013
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS

towards the center.
diameter.
F097
GROOVING SYSTEM

3-2

GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
4.00
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
Order Number
ID
Modular Blade
Stock
40
50
14
(4E1R4G11) GYM25RD-G14-040
50
60
14
(4E1R4G12) GYM25RD-G14-050
60
85
125
125
200
180
280
250
999
(4E1R4G13) GYM25RD-G14-060
1 (4E1R4G23) GYM25RD-G25-060
(4E1R4G14) GYM25RD-G14-085
1 (4E1R4G24) GYM25RD-G25-085
(4E1R4G15) GYM25RD-G14-125
1 (4E1R4G25) GYM25RD-G25-125
(4E1R4G16) GYM25RD-G14-180
1 (4E1R4G26) GYM25RD-G25-180
(4E1R4G17) GYM25RD-G14-250
1 (4E1R4G27) GYM25RD-G25-250
85
14
25
14
25
14
25
14
25
14
25
40
50
14
(4G1R4G11) GYM25RD-G14-040
50
60
14
(4G1R4G12) GYM25RD-G14-050
60
85
125
125
200
180
280
250
999
(4G1R4G13) GYM25RD-G14-060
1 (4G1R4G23) GYM25RD-G25-060
(4G1R4G14) GYM25RD-G14-085
1 (4G1R4G24) GYM25RD-G25-085
(4G1R4G15) GYM25RD-G14-125
1 (4G1R4G25) GYM25RD-G25-125
(4G1R4G16) GYM25RD-G14-180
1 (4G1R4G26) GYM25RD-G25-180
(4G1R4G17) GYM25RD-G14-250
1 (4G1R4G27) GYM25RD-G25-250
85
14
25
14
25
14
25
14
25
14
25
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHR2020K00-M25R
GYHR2525M00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*12 The
*

F098
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
Fig. 4
GYHR2020K00-M25R
GYHR2525M00-M25R
Dimensions (mm)
*2
(5 pcs.)
Wrench
GY06013M
TS55
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
S3
20
20
125
39
20
26
20
20
125
39
20
26
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
125
136
125
136
125
136
125
136
125
136
39
50
39
50
39
50
39
50
39
50
20
20
20
20
20
20
20
20
20
20
26
26
26
26
26
26
26
26
26
26
5
5
5
5
5
5
5
5
5
5
3
4
3
4
3
4
3
4
3
4
25
25
150
39
25
28
25
25
150
39
25
28
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
161
150
161
150
161
150
161
150
161
39
50
39
50
39
50
39
50
39
50
25
25
25
25
25
25
25
25
25
25
28
28
28
28
28
28
28
28
28
28

1
2
1
2
1
2
1
2
1
2
Cutting Mode
Page
GY2M0400G030N-GU
GROOVING
Fig. 3
GY2M0400G020N-GS
GY2M0400G030N-GM
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
(Gauge insert)
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS

towards the center.
diameter.
F099
GROOVING SYSTEM

3-2

GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
4.00
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
Order Number
ID
Modular Blade
Stock
40
50
14
(4Q1R4G11) GYM25RD-G14-040
50
60
14
(4Q1R4G12) GYM25RD-G14-050
60
85
125
125
200
180
280
250
999
(4Q1R4G13) GYM25RD-G14-060
1 (4Q1R4G23) GYM25RD-G25-060
(4Q1R4G14) GYM25RD-G14-085
1 (4Q1R4G24) GYM25RD-G25-085
(4Q1R4G15) GYM25RD-G14-125
1 (4Q1R4G25) GYM25RD-G25-125
(4Q1R4G16) GYM25RD-G14-180
1 (4Q1R4G26) GYM25RD-G25-180
(4Q1R4G17) GYM25RD-G14-250
1 (4Q1R4G27) GYM25RD-G25-250
85
14
25
14
25
14
25
14
25
14
25
40
50
14
(4J1R4G11) GYM25RD-G14-040
50
60
14
(4J1R4G12) GYM25RD-G14-050
60
85
125
125
200
180
280
250
999
(4J1R4G13) GYM25RD-G14-060
1 (4J1R4G23) GYM25RD-G25-060
(4J1R4G14) GYM25RD-G14-085
1 (4J1R4G24) GYM25RD-G25-085
(4J1R4G15) GYM25RD-G14-125
1 (4J1R4G25) GYM25RD-G25-125
(4J1R4G16) GYM25RD-G14-180
1 (4J1R4G26) GYM25RD-G25-180
(4J1R4G17) GYM25RD-G14-250
1 (4J1R4G27) GYM25RD-G25-250
85
14
25
14
25
14
25
14
25
14
25
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHR3225P00-M25R
GYHR3232P00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*12 The
*

F100
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHR3225P00-M25R
GYHR3232P00-M25R
*2
Wrench
GY06013M
TS55
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
32
25
170
39
32
28
32
25
170
39
32
28
32
32
32
32
32
32
32
32
32
32
25
25
25
25
25
25
25
25
25
25
170
181
170
181
170
181
170
181
170
181
39
50
39
50
39
50
39
50
39
50
32
32
32
32
32
32
32
32
32
32
28
28
28
28
28
28
28
28
28
28
1
2
1
2
1
2
1
2
1
2
32
32
170
39
32
35
32
32
170
39
32
35
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
170
181
170
181
170
181
170
181
170
181
39
50
39
50
39
50
39
50
39
50
32
32
32
32
32
32
32
32
32
32
35
35
35
35
35
35
35
35
35
35
1
2
1
2
1
2
1
2
1
2
Cutting Mode
Page
GROOVING
Dimensions (mm)
(5 pcs.)
GY2M0400G030N-GU
GY2M0400G020N-GS
GY2M0400G030N-GM
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
(Gauge insert)
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS

towards the center.
diameter.
F101
GROOVING SYSTEM

3-2

GS
Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(mm)
4.00
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
Order Number
ID
Modular Blade
Stock
40
50
14
(4E1L4G11) GYM25LD-G14-040
50
60
14
(4E1L4G12) GYM25LD-G14-050
60
85
125
125
200
180
280
250
999
(4E1L4G13) GYM25LD-G14-060
1 (4E1L4G23) GYM25LD-G25-060
(4E1L4G14) GYM25LD-G14-085
1 (4E1L4G24) GYM25LD-G25-085
(4E1L4G15) GYM25LD-G14-125
1 (4E1L4G25) GYM25LD-G25-125
(4E1L4G16) GYM25LD-G14-180
1 (4E1L4G26) GYM25LD-G25-180
(4E1L4G17) GYM25LD-G14-250
1 (4E1L4G27) GYM25LD-G25-250
85
14
25
14
25
14
25
14
25
14
25
40
50
14
(4G1L4G11) GYM25LD-G14-040
50
60
14
(4G1L4G12) GYM25LD-G14-050
60
85
125
125
200
180
280
250
999
(4G1L4G13) GYM25LD-G14-060
1 (4G1L4G23) GYM25LD-G25-060
(4G1L4G14) GYM25LD-G14-085
1 (4G1L4G24) GYM25LD-G25-085
(4G1L4G15) GYM25LD-G14-125
1 (4G1L4G25) GYM25LD-G25-125
(4G1L4G16) GYM25LD-G14-180
1 (4G1L4G26) GYM25LD-G25-180
(4G1L4G17) GYM25LD-G14-250
1 (4G1L4G27) GYM25LD-G25-250
85
14
25
14
25
14
25
14
25
14
25
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHL2020K00-M25L
GYHL2525M00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F102
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
Fig. 4

GYHL2020K00-M25L
GYHL2525M00-M25L
Dimensions (mm)
*2
(5 pcs.)
Wrench
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
S3
20
20
125
39
20
26
20
20
125
39
20
26
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
125
136
125
136
125
136
125
136
125
136
39
50
39
50
39
50
39
50
39
50
20
20
20
20
20
20
20
20
20
20
26
26
26
26
26
26
26
26
26
26
5
5
5
5
5
5
5
5
5
5
3
4
3
4
3
4
3
4
3
4
25
25
150
39
25
28
25
25
150
39
25
28
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
161
150
161
150
161
150
161
150
161
39
50
39
50
39
50
39
50
39
50
25
25
25
25
25
25
25
25
25
25
28
28
28
28
28
28
28
28
28
28

1
2
1
2
1
2
1
2
1
2
Cutting Mode
Page
GY2M0400G030N-GU
GROOVING
Fig. 3
GY2M0400G020N-GS
GY2M0400G030N-GM
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
(Gauge insert)
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS

towards the center.
diameter.
F103
GROOVING SYSTEM

3-2

GS
Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(mm)
4.00
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
Order Number
ID
Modular Blade
Stock
40
50
14
(4Q1L4G11) GYM25LD-G14-040
50
60
14
(4Q1L4G12) GYM25LD-G14-050
60
85
125
125
200
180
280
250
999
(4Q1L4G13) GYM25LD-G14-060
1 (4Q1L4G23) GYM25LD-G25-060
(4Q1L4G14) GYM25LD-G14-085
1 (4Q1L4G24) GYM25LD-G25-085
(4Q1L4G15) GYM25LD-G14-125
1 (4Q1L4G25) GYM25LD-G25-125
(4Q1L4G16) GYM25LD-G14-180
1 (4Q1L4G26) GYM25LD-G25-180
(4Q1L4G17) GYM25LD-G14-250
1 (4Q1L4G27) GYM25LD-G25-250
85
14
25
14
25
14
25
14
25
14
25
40
50
14
(4J1L4G11) GYM25LD-G14-040
50
60
14
(4J1L4G12) GYM25LD-G14-050
60
85
125
125
200
(4J1L4G13) GYM25LD-G14-060
1 (4J1L4G23) GYM25LD-G25-060
(4J1L4G14) GYM25LD-G14-085
1 (4J1L4G24) GYM25LD-G25-085
(4J1L4G15) GYM25LD-G14-125
1 (4J1L4G25) GYM25LD-G25-125
(4J1L4G16) GYM25LD-G14-180
1 (4J1L4G26) GYM25LD-G25-180
(4J1L4G17) GYM25LD-G14-250
1 (4J1L4G27) GYM25LD-G25-250
85
14
25
14
25
14
25
14
25
14
25
180
280
250
999
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHL3225P00-M25L
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F104
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHL3225P00-M25L
GYHL3232P00-M25L
*2
Wrench
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Insert
Fig.
Cutting Mode
H1
L1
L2
H2
F1
32
25
170
39
32
28
32
25
170
39
32
28
32
32
32
32
32
32
32
32
32
32
25
25
25
25
25
25
25
25
25
25
170
181
170
181
170
181
170
181
170
181
39
50
39
50
39
50
39
50
39
50
32
32
32
32
32
32
32
32
32
32
28
28
28
28
28
28
28
28
28
28
1
2
1
2
1
2
1
2
1
2
32
32
170
39
32
35
32
32
170
39
32
35
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
170
181
170
181
170
181
170
181
170
181
39
50
39
50
39
50
39
50
39
50
32
32
32
32
32
32
32
32
32
32
35
35
35
35
35
35
35
35
35
35
1
2
1
2
1
2
1
2
1
2
Page
GY2M0400G030N-GU
GROOVING
Dimensions (mm)
(5 pcs.)
GY2M0400G020N-GS
GY2M0400G030N-GM
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
(Gauge insert)
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS

towards the center.
diameter.
F105
GROOVING SYSTEM

3-2

GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
4.75
5.00
Hand
(R/L)
3
R*
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
50
60
60
85
85
125
125
200
180
280
250
999
50
60
60
85
85
125
125
200
180
280
250
999
Order Number
ID
Modular Blade
Stock
14
(4E1R4H11) GYM25RD-H14-050
14
25
14
25
14
25
14
25
14
25
(4E1R4H12) GYM25RD-H14-060
1 (4E1R4H22) GYM25RD-H25-060
(4E1R4H13) GYM25RD-H14-085
1 (4E1R4H23) GYM25RD-H25-085
(4E1R4H14) GYM25RD-H14-125
1 (4E1R4H24) GYM25RD-H25-125
(4E1R4H15) GYM25RD-H14-180
1 (4E1R4H25) GYM25RD-H25-180
(4E1R4H16) GYM25RD-H14-250
1 (4E1R4H26) GYM25RD-H25-250
14
(4G1R4H11) GYM25RD-H14-050
14
25
14
25
14
25
14
25
14
25
(4G1R4H12) GYM25RD-H14-060
1 (4G1R4H22) GYM25RD-H25-060
(4G1R4H13) GYM25RD-H14-085
1 (4G1R4H23) GYM25RD-H25-085
(4G1R4H14) GYM25RD-H14-125
1 (4G1R4H24) GYM25RD-H25-125
(4G1R4H15) GYM25RD-H14-180
1 (4G1R4H25) GYM25RD-H25-180
(4G1R4H16) GYM25RD-H14-250
1 (4G1R4H26) GYM25RD-H25-250
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHR2020K00-M25R
GYHR2525M00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*12 The
*

F106
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
Fig. 4
GYHR2020K00-M25R
GYHR2525M00-M25R
Dimensions (mm)
*2
(5 pcs.)
Wrench
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
S3
20
20
125
39
20
26
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
125
136
125
136
125
136
125
136
125
136
39
50
39
50
39
50
39
50
39
50
20
20
20
20
20
20
20
20
20
20
26
26
26
26
26
26
26
26
26
26
5
5
5
5
5
5
5
5
5
5
3
4
3
4
3
4
3
4
3
4
Cutting Mode
25
25
150
39
25
28
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
161
150
161
150
161
150
161
150
161
39
50
39
50
39
50
39
50
39
50
25
25
25
25
25
25
25
25
25
25
28
28
28
28
28
28
28
28
28
28

1
2
1
2
1
2
1
2
1
2
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Fig. 3
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
GY2M0500H040R05-GM
GY2M0500H040L05-GM
GY2M0500H040N-MS
GY2M0500H080N-MS
F012
F013
(Gauge insert)
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS

towards the center.
diameter.
F107
GROOVING SYSTEM

3-2

GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
4.75
5.00
Hand
(R/L)
*3
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
50
60
60
85
85
125
125
200
180
280
250
999
50
60
60
85
85
125
125
200
180
280
250
999
Order Number
ID
Modular Blade
Stock
14
(4Q1R4H11) GYM25RD-H14-050
14
25
14
25
14
25
14
25
14
25
(4Q1R4H12) GYM25RD-H14-060
1 (4Q1R4H22) GYM25RD-H25-060
(4Q1R4H13) GYM25RD-H14-085
1 (4Q1R4H23) GYM25RD-H25-085
(4Q1R4H14) GYM25RD-H14-125
1 (4Q1R4H24) GYM25RD-H25-125
(4Q1R4H15) GYM25RD-H14-180
1 (4Q1R4H25) GYM25RD-H25-180
(4Q1R4H16) GYM25RD-H14-250
1 (4Q1R4H26) GYM25RD-H25-250
14
(4J1R4H11) GYM25RD-H14-050
14
25
14
25
14
25
14
25
14
25
(4J1R4H12) GYM25RD-H14-060
1 (4J1R4H22) GYM25RD-H25-060
(4J1R4H13) GYM25RD-H14-085
1 (4J1R4H23) GYM25RD-H25-085
(4J1R4H14) GYM25RD-H14-125
1 (4J1R4H24) GYM25RD-H25-125
(4J1R4H15) GYM25RD-H14-180
1 (4J1R4H25) GYM25RD-H25-180
(4J1R4H16) GYM25RD-H14-250
1 (4J1R4H26) GYM25RD-H25-250
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHR3225P00-M25R
GYHR3232P00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*12 The
*

F108
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHR3225P00-M25R
GYHR3232P00-M25R
*2
Wrench
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Insert
Fig.
Cutting Mode
H1
L1
L2
H2
F1
32
25
170
39
32
28
32
32
32
32
32
32
32
32
32
32
25
25
25
25
25
25
25
25
25
25
170
181
170
181
170
181
170
181
170
181
39
50
39
50
39
50
39
50
39
50
32
32
32
32
32
32
32
32
32
32
28
28
28
28
28
28
28
28
28
28
1
2
1
2
1
2
1
2
1
2
32
32
170
39
32
35
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
170
181
170
181
170
181
170
181
170
181
39
50
39
50
39
50
39
50
39
50
32
32
32
32
32
32
32
32
32
32
35
35
35
35
35
35
35
35
35
35
1
2
1
2
1
2
1
2
1
2
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Dimensions (mm)
(5 pcs.)
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
GY2M0500H040R05-GM
GY2M0500H040L05-GM F012
F013
GY2M0500H040N-MS
GY2M0500H080N-MS
(Gauge insert)
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS

towards the center.
diameter.
F109
GROOVING SYSTEM

3-2

GS
Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(mm)
4.75
5.00
Hand
(R/L)
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
50
60
60
85
85
125
125
200
180
280
250
999
50
60
60
85
85
125
125
200
180
280
250
999
Order Number
ID
Modular Blade
Stock
14
(4E1L4H11) GYM25LD-H14-050
14
25
14
25
14
25
14
25
14
25
(4E1L4H12) GYM25LD-H14-060
1 (4E1L4H22) GYM25LD-H25-060
(4E1L4H13) GYM25LD-H14-085
1 (4E1L4H23) GYM25LD-H25-085
(4E1L4H14) GYM25LD-H14-125
1 (4E1L4H24) GYM25LD-H25-125
(4E1L4H15) GYM25LD-H14-180
1 (4E1L4H25) GYM25LD-H25-180
(4E1L4H16) GYM25LD-H14-250
1 (4E1L4H26) GYM25LD-H25-250
14
(4G1L4H11) GYM25LD-H14-050
14
25
14
25
14
25
14
25
14
25
(4G1L4H12) GYM25LD-H14-060
1 (4G1L4H22) GYM25LD-H25-060
(4G1L4H13) GYM25LD-H14-085
1 (4G1L4H23) GYM25LD-H25-085
(4G1L4H14) GYM25LD-H14-125
1 (4G1L4H24) GYM25LD-H25-125
(4G1L4H15) GYM25LD-H14-180
1 (4G1L4H25) GYM25LD-H25-180
(4G1L4H16) GYM25LD-H14-250
1 (4G1L4H26) GYM25LD-H25-250
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHL2020K00-M25L
GYHL2525M00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F110
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
Fig. 4

GYHL2020K00-M25L
GYHL2525M00-M25L
Dimensions (mm)
*2
(5 pcs.)
Wrench
TS55
GY06013M
xTKY25D
: 44 lbf-in)
: 53 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
S3
20
20
125
39
20
26
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
125
136
125
136
125
136
125
136
125
136
39
50
39
50
39
50
39
50
39
50
20
20
20
20
20
20
20
20
20
20
26
26
26
26
26
26
26
26
26
26
5
5
5
5
5
5
5
5
5
5
3
4
3
4
3
4
3
4
3
4
Cutting Mode
25
25
150
39
25
28
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
161
150
161
150
161
150
161
150
161
39
50
39
50
39
50
39
50
39
50
25
25
25
25
25
25
25
25
25
25
28
28
28
28
28
28
28
28
28
28

1
2
1
2
1
2
1
2
1
2
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Fig. 3
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
GY2M0500H040R05-GM
GY2M0500H040L05-GM
GY2M0500H040N-MS
GY2M0500H080N-MS
F012
F013
(Gauge insert)
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS

towards the center.
diameter.
F111
GROOVING SYSTEM

3-2

GS
Fig. 1
Fig. 2
GROOVING
Seat
Size
Insert
Width
W3
(mm)
4.75
5.00
Hand
(R/L)
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
50
60
60
85
85
125
125
200
180
280
250
999
50
60
60
85
85
125
125
200
180
280
250
999
Order Number
ID
Modular Blade
Stock
14
(4Q1L4H11) GYM25LD-H14-050
14
25
14
25
14
25
14
25
14
25
(4Q1L4H12) GYM25LD-H14-060
1 (4Q1L4H22) GYM25LD-H25-060
(4Q1L4H13) GYM25LD-H14-085
1 (4Q1L4H23) GYM25LD-H25-085
(4Q1L4H14) GYM25LD-H14-125
1 (4Q1L4H24) GYM25LD-H25-125
(4Q1L4H15) GYM25LD-H14-180
1 (4Q1L4H25) GYM25LD-H25-180
(4Q1L4H16) GYM25LD-H14-250
1 (4Q1L4H26) GYM25LD-H25-250
14
(4J1L4H11) GYM25LD-H14-050
14
25
14
25
14
25
14
25
14
25
(4J1L4H12) GYM25LD-H14-060
1 (4J1L4H22) GYM25LD-H25-060
(4J1L4H13) GYM25LD-H14-085
1 (4J1L4H23) GYM25LD-H25-085
(4J1L4H14) GYM25LD-H14-125
1 (4J1L4H24) GYM25LD-H25-125
(4J1L4H15) GYM25LD-H14-180
1 (4J1L4H25) GYM25LD-H25-180
(4J1L4H16) GYM25LD-H14-250
1 (4J1L4H26) GYM25LD-H25-250
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHL3225P00-M25L
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F112
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHL3225P00-M25L
GYHL3232P00-M25L
*2
Wrench
GY06013M
TS55
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
32
25
170
39
32
28
32
32
32
32
32
32
32
32
32
32
25
25
25
25
25
25
25
25
25
25
170
181
170
181
170
181
170
181
170
181
39
50
39
50
39
50
39
50
39
50
32
32
32
32
32
32
32
32
32
32
28
28
28
28
28
28
28
28
28
28
1
2
1
2
1
2
1
2
1
2
Cutting Mode
32
32
170
39
32
35
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
170
181
170
181
170
181
170
181
170
181
39
50
39
50
39
50
39
50
39
50
32
32
32
32
32
32
32
32
32
32
35
35
35
35
35
35
35
35
35
35
1
2
1
2
1
2
1
2
1
2
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Dimensions (mm)
(5 pcs.)
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
GY2M0500H040R05-GM
GY2M0500H040L05-GM
GY2M0500H040N-MS
GY2M0500H080N-MS
F012
F013
(Gauge insert)
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS

towards the center.
diameter.
F113
GROOVING SYSTEM

3-2

L2
Fig. 2
H1
H2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
6.00
6.35
Hand
(R/L)
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
50
70
70
110
110
200
170
280
250
999
50
70
70
110
110
200
170
280
250
999
50
70
70
110
110
200
170
280
250
999
50
70
70
110
110
200
170
280
250
999
14
14
25
14
25
14
25
14
25
14
14
25
14
25
14
25
14
25
14
14
25
14
25
14
25
14
25
14
14
25
14
25
14
25
14
25
*
*1
*1
*1
1
*
*1
*1
*1
1
*
*1
*1
*1
1
*
*1
*1
*1
Order Number
ID
(4E1R4J11)
(4E1R4J12)
(4E1R4J22)
(4E1R4J13)
(4E1R4J23)
(4E1R4J14)
(4E1R4J24)
(4E1R4J15)
(4E1R4J25)
(4G1R4J11)
(4G1R4J12)
(4G1R4J22)
(4G1R4J13)
(4G1R4J23)
(4G1R4J14)
(4G1R4J24)
(4G1R4J15)
(4G1R4J25)
(4Q1R4J11)
(4Q1R4J12)
(4Q1R4J22)
(4Q1R4J13)
(4Q1R4J23)
(4Q1R4J14)
(4Q1R4J24)
(4Q1R4J15)
(4Q1R4J25)
(4J1R4J11)
(4J1R4J12)
(4J1R4J22)
(4J1R4J13)
(4J1R4J23)
(4J1R4J14)
(4J1R4J24)
(4J1R4J15)
(4J1R4J25)
Modular Blade
Stock
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
GYM25RD-J25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
GYM25RD-J25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
GYM25RD-J25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
GYM25RD-J25-250
Modular Holder
Stock
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*
F114
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
(5 pcs.)

Fig. 4
Fig. 3
x
Wrench
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GY06013M
TS55
zTKY30R
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
GYHR3232P00-M25R
*2
Insert
Fig.
H1
L1
L2
H2
F1
S3
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
125
125
136
125
136
125
136
125
136
150
150
161
150
161
150
161
150
161
170
170
181
170
181
170
181
170
181
170
170
181
170
181
170
181
170
181
39
39
50
39
50
39
50
39
50
39
39
50
39
50
39
50
39
50
39
39
50
39
50
39
50
39
50
39
39
50
39
50
39
50
39
50
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
26
26
26
26
26
26
26
26
26
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
35
35
35
35
35
35
35
35
35
5
5
5
5
5
5
5
5
5

Cutting Mode
3
3
4
3
4
3
4
3
4
1
1
2
1
2
1
2
1
2
1
1
2
1
2
1
2
1
2
1
1
2
1
2
1
2
1
2
Page
GROOVING
Dimensions (mm)
GY2M0600J040N-GU
GY2M0635J040N-GU
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
GY2M0635J040N-GM
GY2M0600J040N-MS
GY2M0600J080N-MS
F012
F013
(Gauge insert)
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM

towards the center.
diameter.
F115
GROOVING SYSTEM

3-2

Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
6.00
6.35
Hand
(R/L)
First Cut Diameter

Max.
Groove Depth
D1 (mm)
ar
Min.
Max.
(mm)
50
70
70
110
110
200
170
280
250
999
50
70
70
110
110
200
170
280
250
999
50
70
70
110
110
200
170
280
250
999
50
70
70
110
110
200
170
280
250
999
14
14
25
14
25
14
25
14
25
14
14
25
14
25
14
25
14
25
14
14
25
14
25
14
25
14
25
14
14
25
14
25
14
25
14
25
*
*1
*1
*1
1
*
*1
*1
*1
1
*
*1
*1
*1
1
*
*1
*1
*1
Order Number
ID
(4E1L4J11)
(4E1L4J12)
(4E1L4J22)
(4E1L4J13)
(4E1L4J23)
(4E1L4J14)
(4E1L4J24)
(4E1L4J15)
(4E1L4J25)
(4G1L4J11)
(4G1L4J12)
(4G1L4J22)
(4G1L4J13)
(4G1L4J23)
(4G1L4J14)
(4G1L4J24)
(4G1L4J15)
(4G1L4J25)
(4Q1L4J11)
(4Q1L4J12)
(4Q1L4J22)
(4Q1L4J13)
(4Q1L4J23)
(4Q1L4J14)
(4Q1L4J24)
(4Q1L4J15)
(4Q1L4J25)
(4J1L4J11)
(4J1L4J12)
(4J1L4J22)
(4J1L4J13)
(4J1L4J23)
(4J1L4J14)
(4J1L4J24)
(4J1L4J15)
(4J1L4J25)
Modular Blade
Stock
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
GYM25LD-J25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
GYM25LD-J25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
GYM25LD-J25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
GYM25LD-J25-250
Modular Holder
Stock
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*
F116
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
(5 pcs.)

Fig. 4
Fig. 3
x
Wrench
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GY06013M
TS55
zTKY30R
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
GYHL3232P00-M25L
*2
Insert
Fig.
H1
L1
L2
H2
F1
S3
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
125
125
136
125
136
125
136
125
136
150
150
161
150
161
150
161
150
161
170
170
181
170
181
170
181
170
181
170
170
181
170
181
170
181
170
181
39
39
50
39
50
39
50
39
50
39
39
50
39
50
39
50
39
50
39
39
50
39
50
39
50
39
50
39
39
50
39
50
39
50
39
50
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
26
26
26
26
26
26
26
26
26
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
35
35
35
35
35
35
35
35
35
5
5
5
5
5
5
5
5
5

Cutting Mode
3
3
4
3
4
3
4
3
4
1
1
2
1
2
1
2
1
2
1
1
2
1
2
1
2
1
2
1
1
2
1
2
1
2
1
2
Page
GROOVING
Dimensions (mm)
GY2M0600J040N-GU
GY2M0635J040N-GU
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
GY2M0635J040N-GM
GY2M0600J040N-MS
GY2M0600J080N-MS
F012
F013
(Gauge insert)
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM

towards the center.
diameter.
F117
GROOVING SYSTEM

4-2
GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Hand
(R/L)
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
3.00
3.18
Modular Blade
Stock
35
40
12
(5G1R4F11) GYM25LD-F12-035
40
50
12
(5G1R4F12) GYM25LD-F12-040
50
60
12
(5G1R4F13) GYM25LD-F12-050
60
75
100
100
150
135
200
180
250
(5G1R4F14) GYM25LD-F12-060
1 (5G1R4F24) GYM25LD-F20-060
(5G1R4F15) GYM25LD-F12-075
1 (5G1R4F25) GYM25LD-F20-075
(5G1R4F16) GYM25LD-F12-100
1 (5G1R4F26) GYM25LD-F20-100
(5G1R4F17) GYM25LD-F12-135
1 (5G1R4F27) GYM25LD-F20-135
(5G1R4F18) GYM25LD-F12-180
1 (5G1R4F28) GYM25LD-F20-180
75
12
20
12
20
12
20
12
20
12
20
35
40
12
(5G1L4F11) GYM25RD-F12-035
40
50
12
(5G1L4F12) GYM25RD-F12-040
50
60
12
(5G1L4F13) GYM25RD-F12-050
60
75
100
100
150
135
200
180
250
(5G1L4F14) GYM25RD-F12-060
1 (5G1L4F24) GYM25RD-F20-060
(5G1L4F15) GYM25RD-F12-075
1 (5G1L4F25) GYM25RD-F20-075
(5G1L4F16) GYM25RD-F12-100
1 (5G1L4F26) GYM25RD-F20-100
(5G1L4F17) GYM25RD-F12-135
1 (5G1L4F27) GYM25RD-F20-135
(5G1L4F18) GYM25RD-F12-180
1 (5G1L4F28) GYM25RD-F20-180
75
12
20
12
20
12
20
12
20
12
20
Order Number
ID
*
*
*
*
*
*
*
*
*
*
a
a
Modular Holder
Stock
GYHR2525M90-M25L
GYHL2525M90-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F118
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHR2525M90-M25L
GYHL2525M90-M25R
*2
Wrench
GY06013M
TS55
zTKY30R
xTKY25D
)
)
: 53 lbf-in
: 44 lbf-in
Insert
Fig.
H1
L1
L2
H2
F1
25
25
150
38
25
53
25
25
150
38
25
53
25
25
150
38
25
53
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
25
25
53
59
53
59
53
59
53
59
53
59
1
2
1
2
1
2
1
2
1
2
Cutting Mode
25
25
150
38
25
53
25
25
150
38
25
53
25
25
150
38
25
53
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
25
25
53
59
53
59
53
59
53
59
53
59
1
2
1
2
1
2
1
2
1
2
Page
GROOVING
Dimensions (mm)
(5 pcs.)
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0300F030N-GM
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
(Gauge insert)
F012
F013
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS

towards the center.
diameter.
F119
GROOVING SYSTEM

4-2
GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Hand
(R/L)
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
Modular Blade
Stock
40
50
14
(5G1R4G11) GYM25LD-G14-040
50
60
14
(5G1R4G12) GYM25LD-G14-050
60
85
125
125
200
180
280
250
999
(5G1R4G13) GYM25LD-G14-060
1 (5G1R4G23) GYM25LD-G25-060
(5G1R4G14) GYM25LD-G14-085
1 (5G1R4G24) GYM25LD-G25-085
(5G1R4G15) GYM25LD-G14-125
1 (5G1R4G25) GYM25LD-G25-125
(5G1R4G16) GYM25LD-G14-180
1 (5G1R4G26) GYM25LD-G25-180
(5G1R4G17) GYM25LD-G14-250
1 (5G1R4G27) GYM25LD-G25-250
85
14
25
14
25
14
25
14
25
14
25
40
50
14
(5G1L4G11) GYM25RD-G14-040
50
60
14
(5G1L4G12) GYM25RD-G14-050
60
85
125
125
200
180
280
250
999
(5G1L4G13) GYM25RD-G14-060
1 (5G1L4G23) GYM25RD-G25-060
(5G1L4G14) GYM25RD-G14-085
1 (5G1L4G24) GYM25RD-G25-085
(5G1L4G15) GYM25RD-G14-125
1 (5G1L4G25) GYM25RD-G25-125
(5G1L4G16) GYM25RD-G14-180
1 (5G1L4G26) GYM25RD-G25-180
(5G1L4G17) GYM25RD-G14-250
1 (5G1L4G27) GYM25RD-G25-250
85
14
25
14
25
14
25
14
25
14
25
Order Number
ID
4.00
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHR2525M90-M25L
GYHL2525M90-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F120
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHR2525M90-M25L
GYHL2525M90-M25R
*2
Wrench
GY06013M
TS55
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
25
25
150
38
25
53
25
25
150
38
25
53
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
25
25
53
64
53
64
53
64
53
64
53
64
1
2
1
2
1
2
1
2
1
2
25
25
150
38
25
53
25
25
150
38
25
53
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
25
25
53
64
53
64
53
64
53
64
53
64
1
2
1
2
1
2
1
2
1
2
Cutting Mode
Page
GY2M0400G030N-GU
GROOVING
Dimensions (mm)
(5 pcs.)
GY2M0400G020N-GS
GY2M0400G030N-GM
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
(Gauge insert)
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS

towards the center.
diameter.
F121
GROOVING SYSTEM

4-2
GS
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Hand
(R/L)
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
50
60
60
85
85
125
125
200
180
280
250
999
50
60
60
85
85
125
125
200
180
280
250
999
4.75
5.00
Order Number
ID
Modular Blade
Stock
14
(5G1R4H11) GYM25LD-H14-050
14
25
14
25
14
25
14
25
14
25
(5G1R4H12) GYM25LD-H14-060
1 (5G1R4H22) GYM25LD-H25-060
(5G1R4H13) GYM25LD-H14-085
1 (5G1R4H23) GYM25LD-H25-085
(5G1R4H14) GYM25LD-H14-125
1 (5G1R4H24) GYM25LD-H25-125
(5G1R4H15) GYM25LD-H14-180
1 (5G1R4H25) GYM25LD-H25-180
(5G1R4H16) GYM25LD-H14-250
1 (5G1R4H26) GYM25LD-H25-250
14
(5G1L4H11) GYM25RD-H14-050
14
25
14
25
14
25
14
25
14
25
(5G1L4H12) GYM25RD-H14-060
1 (5G1L4H22) GYM25RD-H25-060
(5G1L4H13) GYM25RD-H14-085
1 (5G1L4H23) GYM25RD-H25-085
(5G1L4H14) GYM25RD-H14-125
1 (5G1L4H24) GYM25RD-H25-125
(5G1L4H15) GYM25RD-H14-180
1 (5G1L4H25) GYM25RD-H25-180
(5G1L4H16) GYM25RD-H14-250
1 (5G1L4H26) GYM25RD-H25-250
*
*
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHR2525M90-M25L
GYHL2525M90-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F122
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
GYHR2525M90-M25L
GYHL2525M90-M25R
*2
Wrench
GY06013M
TS55
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
Cutting Mode
H1
L1
L2
H2
F1
25
25
150
38
25
53
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
25
25
53
64
53
64
53
64
53
64
53
64
1
2
1
2
1
2
1
2
1
2
25
25
150
38
25
53
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
25
25
53
64
53
64
53
64
53
64
53
64
1
2
1
2
1
2
1
2
1
2
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Dimensions (mm)
(5 pcs.)
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
GY2M0500H040R05-GM
GY2M0500H040L05-GM F012
F013
GY2M0500H040N-MS
GY2M0500H080N-MS
(Gauge insert)
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS

towards the center.
diameter.
F123
GROOVING SYSTEM

4-2
Fig. 2
Fig. 1
GROOVING
Seat
Size
Insert
Width
W3
(mm)
Hand
(R/L)
6.00
6.35
First Cut Diameter

Max.
D1 (mm)
Groove Depth
ar
Min.
Max.
(mm)
50
70
70
110
110
200
170
280
250
999
50
70
70
110
110
200
170
280
250
999
Order Number
ID
Modular Blade
Stock
14
(5G1R4J11) GYM25LD-J14-050
14
25
14
25
14
25
14
25
(5G1R4J12) GYM25LD-J14-070
1 (5G1R4J22) GYM25LD-J25-070
(5G1R4J13) GYM25LD-J14-110
1 (5G1R4J23) GYM25LD-J25-110
(5G1R4J14) GYM25LD-J14-170
1 (5G1R4J24) GYM25LD-J25-170
(5G1R4J15) GYM25LD-J14-250
1 (5G1R4J25) GYM25LD-J25-250
14
(5G1L4J11) GYM25RD-J14-050
14
25
14
25
14
25
14
25
(5G1L4J12) GYM25RD-J14-070
1 (5G1L4J22) GYM25RD-J25-070
(5G1L4J13) GYM25RD-J14-110
1 (5G1L4J23) GYM25RD-J25-110
(5G1L4J14) GYM25RD-J14-170
1 (5G1L4J24) GYM25RD-J25-170
(5G1L4J15) GYM25RD-J14-250
1 (5G1L4J25) GYM25RD-J25-250
*
*
*
*
*
*
*
*
Modular Holder
Stock
GYHR2525M90-M25L
GYHL2525M90-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*21 Dimensions
*

F124
&D1 (Min.)
&D1 (Max.)

SPARE PARTS
z
(5 pcs.)
GYHR2525M90-M25L
GYHL2525M90-M25R
*2
GY06013M
TS55
xTKY25D
: 53 lbf-in)
: 44 lbf-in)
Insert
Fig.
H1
L1
L2
H2
F1
25
25
150
38
25
53
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
53
64
53
64
53
64
53
64
1
2
1
2
1
2
1
2
Cutting Mode
25
25
150
38
25
53
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
53
64
53
64
53
64
53
64
1
2
1
2
1
2
1
2
Page
GY2M0600J040N-GU
GY2M0635J040N-GU
GROOVING
Dimensions (mm)
x
Wrench
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
GY2M0635J040N-GM
GY2M0600J040N-MS
GY2M0600J080N-MS
F012
F013
(Gauge insert)
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM

towards the center.
diameter.
F125
GROOVING SYSTEM
Recommended Cutting Conditions (Face Grooving)
Grooving
Insert width (inch)
: 1st
recommended area
Feed (IPR)
Plunging
Insert width (inch)
GROOVING
: 1st
recommended area
Feed (IPR)
Traverse Machining (MM/MS Breaker)

Insert width .236"
Insert width
.197"
Insert width
.157"
Insert width .118"
Feed (IPR)
Traverse Machining (BM Breaker)
Insert width
.187"
.197"
Insert widt
.157"
Insert width .236"

.250"
Insert width.118",.125"
Feed (IPR)
F126
After the 1st plunge, the width of cut should be set narrower
* than
insert with W3.
Feed (%)
Relationship between the modular blade and feed per rotation
(inch)
Modular Blade (-oo)
(Note) Adjust the feed per rotation in the cutting conditions to the percentage shown in the table above.
Work Material
Hardness
Insert Grade
165
VP20RT
260
825
590
295
VP10RT
Mild Steel
Cutting Speed (SFM)

495
660
330
625
990
GROOVING
< 160HB
360
MY5015
825
230
NX2525
560
195
VP20RT
460
230
VP10RT
495
160-280HB
295
MY5015
NX2525
Carbon Steel
Alloy Steel
VP20RT
180
440
165
360
195
VP10RT
690
390
> 280HB
260
MY5015
NX2525
VP20RT
Stainless Steel
345
360
165
< 270HB
K
Cast Iron
150
Tensile Strength
< 300MPa
VP10RT
195
VP20RT
195
VP20RT
Tensile Strength
< 800MPa
165
Hardened steel
> 50HRC
VP10RT
MB8025
495
690
360
195
VP10RT
VP20RT

Titanium Alloy
460
295
390
260
MY5015
390
230
VP10RT
MY5015
Ductile Cast Iron
525
525
100 195
130 230
195
330
F127
GROOVING SYSTEM
TOOL SELECTION

Modular blade (1)
Modular blade (2)
a Select a modular blade for
face grooving, so that the

cutting diameter at the rst
pass is within the range of
D1 minimum and D1
maximum that are described
in the table of dimensions.
&D1 (Max.)
&D1 (Min.)
aSelect the shortest possible blade suitable for the application.
Modular blade (3)
GROOVING
The maximum cutting diameter
a Select the largest size blade within the
maximum cutting diameter of the

workpiece.
a Machine from the outer diameter
towards the center.
Good
a Increased machining stability and
rigidity is possible if a modular blade

with the largest possible back metal is
used.
NG
a At rst, machine the
maximum cutting
diameter, there is no
restriction in the
cutting diameter on
the remaining
process.
a When plunging in several passes.
a When combining plunging and infeed machining.
Modular holder
Modular holder
Modular holder
aTo ensure sufcient clamping rigidity, select a modular holder with the largest possible shank size.
F128

Setting the cutting edge height
When interfering the wall of groove and the Modular blade
machining towards the center with a very small depth of cut

and ensure that an even surface and no material remains at
the center point afterwards.
aIf interference occurs even when the correct blade is used,
the cutting edge height could be incorrect.

When interference occurs on the inner side of the blade, the
cutting edge height is set too high.
When interference occurs on the outer side of the blade, the
cutting edge height is set too low.
Setting the tool
Tool overhang
Good
NG
.020".039"
Parallel
>.039"
GROOVING
aSet the cutting edge height to .004" parallel to the central axis.
aCutting edge center height check should be done by traverse
Parallel
aSet the insert parallel to the central axis.
aWhen setting the tool, ensure that the overhang is as short as
possible.
MACHINING RECOMMENDATIONS
a Notes when face grooving (1)

aAlways machine from the outer diameter towards the center.
Machining narrow grooves
z
x
c
aPlunging in several passes is recommended.
aCross feed machining is recommended.
F129
GROOVING SYSTEM
MACHINING RECOMMENDATIONS
a Notes when face grooving (2)

Notes on the rst pass (1)
aDuring the rst face grooving pass it is difcult to disperse broken chips and can lead to problems such as a chipped insert.
Maintain longer chips that disperse easily by decreasing the feed per rotation.
GROOVING
Notes on the rst pass (2)
aWhen chips become too long, use peck feed to break them into a suitable length.
plunging in several passes.
ap
Notes when wideNotes

face grooving
plunging
in several
passes. by
whenbywide
face
grooving
aWhen machining a face groove in several passes, machine from the outer diameter towards the center so that space for discharging
chips is created to prevent insert damage caused by chip jamming.

aPlunging width of cut is recommended to be set at 60 - 80% of the insert width. This enhances the effect of the chipbreaker by
enlarging the width of the groove to improve chip dispersal.
Notes
when
wide face
grooving
by plunging in
several
passes.
Notes
when
wide
face grooving
by
combination
of plunging and traverse machining (1)
x
ap2
c
ap3
aWhen face groove machining by using plunge feed and traverse machining, always machine from the outer diameter towards the
center to disperse chips outward to avoid chip jamming problems.

aSet the depth of cut within 40% of the insert width.
F130
Notes when wide face grooving by combination of plunging and traverse machining (2)
aWhen infeed machining at the bottom of deep groove, chips may interfere on the cutting edge near the center wall.
In such cases, stop infeed machining just before the center wall (at a point less than the insert width) then remove the remaining
material by plunging.
GROOVING
Notes when copying (BM Breaker)
ap
aWith the BM breaker insert, 3 dimensional copying is possible. Set the depth of cut (ap) to 30% less than the insert width.
Finishing (1)
aWhen nish cutting, machine continuously from the outer wall to the bottom of the groove, then nally plunge cut the center wall.
Finishing (2) (BM Breaker)
Insert
aCarry out nishing in one process.
ap
For the depth of cut (ap) when back turning, refer to the table on the right.
GY2M0300F150N-BM
GY2M0318F159N-BM
GY2M0400G200N-BM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY2M0600J150N-BM
GY2M0635J318N-BM
ap (inch)
.004
.006
.008
.010
F131
GROOVING SYSTEM
a Assembly procedure
(b) Wrench
(d) Wrench
Holder
(a) Insert clamp screw
x 1pc.
Modular Blade
(Ex.)
x
c
GY M25R D - F 20-060
GY M25R D - F 12-060
z
(Ex.) GYHR2525M00 - M25R
Medium
Long
(c) Modular blade

set screw x 5pcs.
v
Insert
(Ex.)GY2M0300 F 040N-MS
GY2M0318 F 030N-GM
GROOVING
B
Side screws
(3 screws)
Long
modular blade
(5 holes)
Note 2) z and x should be matched. (See caption A)
Note 4)
Front screws
(2 screws)
Note 3)
blade set screws in order of
Note 5)
c and v should be matched.
(See caption A)
E
Good
Note 6)
Dont tighten the insert clamp
screw without installing the insert.
Modular blade might be damaged.
F132
NG
Note 7)
Ensure that the wrench is perpendicular to the
screw tightening.
Assembled
Memo
F133
GROOVING SYSTEM
GY SERIES (INTERNAL GROOVING)

Insert GY2Mooooooooo-GS
GS
a Mono block type (Through air / coolant)
90
ar
D1
Fig. 2
F2
F1
5-1
L3
H1
D4
L1
F2
ar
F1
90
Fig. 1
L3
Seat
Size
Insert
Width
W3
(inch)
Max.
Hand Groove Depth
ar
3
(R/L)
(inch)
GROOVING
Order Number
ID
Holder / Modular Holder
(6F2R9D1)
(6F1R9D1)
(6H2R9D1)
(6H1R9D1)
(6K2R3D1)
(6K1R3D1)
(6M2R3D1)
(6M1R3D1)
(6M2R4D1)
(6M1R4D1)
(6P2R4D1)
(6P1R4D1)
(6F2L9D1)
(6F1L9D1)
(6H2L9D1)
(6H1L9D1)
(6K2L3D1)
(6K1L3D1)
(6M2L3D1)
(6M1L3D1)
(6M2L4D1)
(6M1L4D1)
(6P2L4D1)
(6P1L4D1)
(6F2R9E1)
(6F1R9E1)
(6H2R9E1)
(6H1R9E1)
(6K2R3E1)
(6K1R3E1)
(6M2R3E1)
(6M1R3E1)
(6M2R4E1)
(6M1R4E1)
(6P2R4E1)
(6P1R4E1)
(6F2L9E1)
(6F1L9E1)
(6H2L9E1)
(6H1L9E1)
(6K2L3E1)
(6K1L3E1)
(6M2L3E1)
(6M1L3E1)
(6M2L4E1)
(6M1L4E1)
(6P2L4E1)
(6P1L4E1)
Stock
Modular Blade
a
GYARUS12K90A-D06

a
GYARUS12Q90A-D06
a
GYARUS16K90B-D06
.236
1.250

a
GYARUS16R90B-D06
a
GYDRUS20L90C-M20L
.157 .374
1.625
GYM20LA-D10
a
GYDRUS20S90C-M20L
1
R
GYDRUS24M90D-M20L a
.217 .374
2.000
GYM20LA-D10
a
GYDRUS24T90D-M20L
1
GYDRUS24M90D-M25L a
.276 .453
2.500
GYM25LA-D12
a
GYDRUS24T90D-M25L
1
a
GYDRUS32P90F-M25L
.276 .453
2.750
GYM25LA-D12
a
GYDRUS32T90F-M25L
1
D
.079
a
GYALUS12K90A-D06
.236
1.000

a
GYALUS12Q90A-D06
a
GYALUS16K90B-D06
.236
1.250

a
GYALUS16R90B-D06
a
GYDLUS20L90C-M20R
.157 .374
1.625
GYM20RA-D10
a
GYDLUS20S90C-M20R
1
L
GYDLUS24M90D-M20R a
.217 .374
2.000
GYM20RA-D10
a
GYDLUS24T90D-M20R
1
GYDLUS24M90D-M25R a
.276 .453
2.500
GYM25RA-D12
a
GYDLUS24T90D-M25R
1
a
GYDLUS32P90F-M25R
.276 .453
2.750
GYM25RA-D12
a
GYDLUS32T90F-M25R
1
a
GYARUS12K90A-E06
.236
1.000

a
GYARUS12Q90A-E06
a
GYARUS16K90B-E06
.236
1.250

a
GYARUS16R90B-E06
a
GYDRUS20L90C-M20L
.157 .374
1.625
GYM20LA-E10
a
GYDRUS20S90C-M20L
1
R
GYDRUS24M90D-M20L a
.217 .374
2.000
GYM20LA-E10
a
GYDRUS24T90D-M20L
1
GYDRUS24M90D-M25L a
.276 .453
2.500
GYM25LA-E12
a
GYDRUS24T90D-M25L
1
a
GYDRUS32P90F-M25L
.276 .453
2.750
GYM25LA-E12
.094
a
GYDRUS32T90F-M25L
1
E
a
GYALUS12K90A-E06
.098
.236
1.000

a
GYALUS12Q90A-E06
a
GYALUS16K90B-E06
.236
1.250

a
GYALUS16R90B-E06
a
GYDLUS20L90C-M20R
.157 .374
1.625
GYM20RA-E10
a
GYDLUS20S90C-M20R
1
L
GYDLUS24M90D-M20R a
.217 .374
2.000
GYM20RA-E10
a
GYDLUS24T90D-M20R
1
GYDLUS24M90D-M25R a
.276 .453
2.500
GYM25RA-E12
a
GYDLUS24T90D-M25R
1
a
GYDLUS32P90F-M25R
.276 .453
2.750
GYM25RA-E12
a
GYDLUS32T90F-M25R
1
1 The maximum groove depth varies according to the cutting diameter D1. For details, please refer to page F146.
2 Dimensions shown are when the gauge insert is used. If other insert geometries are used then L1, L3, F1 and F2 values may vary.
.236
1.000
*
*
*
*
*
*
*
*
*
*
*
*
F134
Min.Cutting
Diameter
D1
(inch)
L1
*
*
*
*
*
Stock

a
a
a
a

a
a
a
a

a
a
a
a

a
a
a
a

a Modular blade type (Through air / coolant)
SPARE PARTS
90
z
F1
L3
L1
GYAR/LUS12 o90A- ooo

GYAR/LUS16 o90B- ooo
90
L1

Dimensions (inch)
L1
Wrench
GY05016S
(Clamp Torque
: 40 lbf-in)
TKY20R
TS407
(Clamp Torque
: 31 lbf-in)
TS55
(Clamp Torque
: 44 lbf-in)
zTKY30R
xTKY15D
GYDR/LUS24 o90D-M20L/R GY06013M

(Clamp Torque
: 53 lbf-in)
GYDR/LUS24 o90D-M25L/R
F2
ar
L3
D4
GYDR/LUS20 o90C-M20L/R
F1
Fig. 3
L3
F1
*2
F2
(4 pcs.)
H1
D4
GYDR/LUS32 o90F-M25L/R
zTKY30R
xTKY25D
Insert
Fig.
Cutting Mode
H1
.750 5.000 1.250

.605 .230
.671 1
.750 7.000 1.250
.605 .230
.671 2
1.000 5.000 1.500
.730 .230
.921 1
1.000 8.000 1.500
.730 .230
.921 2
1.250 5.500 2.000
.875 .250 1.171 3
1.250 10.000 2.000
.875 .250 1.171 4
1.500 6.000 2.500 1.125 .375 1.382 3
1.500 12.000 2.500 1.125 .375 1.382 4
1.500 6.000 2.500 1.125 .375 1.382 3
1.500 12.000 2.500 1.125 .375 1.382 4
2.000 6.750 3.250 1.250 .250 1.882 3
2.000 12.000 3.250 1.250 .250 1.882 4
.750 5.000 1.250
.605 .230
.671 1
.750 7.000 1.250
.605 .230
.671 2
1.000 5.000 1.500
.730 .230
.921 1
1.000 8.000 1.500
.730 .230
.921 2
1.250 5.500 2.000
.875 .250 1.171 3
1.250 10.000 2.000
.875 .250 1.171 4
1.500 6.000 2.500 1.125 .375 1.382 3
1.500 12.000 2.500 1.125 .375 1.382 4
1.500 6.000 2.500 1.125 .375 1.382 3
1.500 12.000 2.500 1.125 .375 1.382 4
2.000 6.750 3.250 1.250 .250 1.882 3
2.000 12.000 3.250 1.250 .250 1.882 4
.750 5.000 1.250
.605 .230
.671 1
.750 7.000 1.250
.605 .230
.671 2
1.000 5.000 1.500
.730 .230
.921 1
1.000 8.000 1.500
.730 .230
.921 2
1.250 5.500 2.000
.875 .250 1.171 3
1.250 10.000 2.000
.875 .250 1.171 4
1.500 6.000 2.500 1.125 .375 1.382 3
1.500 12.000 2.500 1.125 .375 1.382 4
1.500 6.000 2.500 1.125 .375 1.382 3
1.500 12.000 2.500 1.125 .375 1.382 4
2.000 6.750 3.250 1.250 .250 1.882 3
2.000 12.000 3.250 1.250 .250 1.882 4
.750 5.000 1.250
.605 .230
.671 1
.750 7.000 1.250
.605 .230
.671 2
1.000 5.000 1.500
.730 .230
.921 1
1.000 8.000 1.500
.730 .230
.921 2
1.250 5.500 2.000
.875 .250 1.171 3
1.250 10.000 2.000
.875 .250 1.171 4
1.500 6.000 2.500 1.125 .375 1.382 3
1.500 12.000 2.500 1.125 .375 1.382 4
1.500 6.000 2.500 1.125 .375 1.382 3
1.500 12.000 2.500 1.125 .375 1.382 4
2.000 6.750 3.250 1.250 .250 1.882 3
2.000 12.000 3.250 1.250 .250 1.882 4
3 The maximum groove depth (ar) is a value within the dimension L3.
Page
GROOVING
Fig. 4
F2
ar
D1
GY2M0200D020N-GS
GY2M0200D020N-GM
(Gauge insert)
GY2M0200D020R05-GM
GY2M0200D020L05-GM
F012
F013
GY2M0200D020N-MM
GY2M0200D100N-BM
GY1G0200D020N-GFGS
GY2M0239E020N-GS
GY2M0250E020N-GS
GY2M0239E020N-GM
GY2M0250E020N-GM
(Gauge insert)
GY2M0250E020R05-GM
GY2M0250E020L05-GM
F012
F013
GY2M0250E020N-MM
GY2M0250E125N-BM
GY1G0239E020N-GFGS
GY1G0250E020N-GFGS
F135
GROOVING SYSTEM

5-1
GS
ar
D1
Fig. 2
F2
F1
90
L3
F2
ar
F1
90
Fig. 1
L3
Insert
Width
W3
(inch)
GROOVING
Seat
Size
Max.
Hand Groove Depth
ar
3
(R/L)
(inch)
.118
.125
1.000
.236
1.250
1
*
.217 .374
*1
.276 .453
*1
.276 .453
*1
2.750
1.250
1
*
.217 .374
*1
.276 .453
*1
.276 .453
*1
*1
.236 .453
*1
.315 .512
*1
.295 .512
*1
1.625
2.000
2.500
2.750
1.250
1.625
2.000
2.500
2.750
.157
.276
.197 .453
F136
2.500
.236
.197 .453
2.000
1.000
.276
1.625
.236
.157 .374
Min.Cutting
Diameter
D1
(inch)
.236
.157 .374
H1
D4
L1
*1
.236 .453
*1
.315 .512
*1
.295 .512
*1
1.250
1.625
2.000
2.500
2.750
L1
Order Number
ID
Stock
(6F2R9F1)
(6F1R9F1)
(6H2R9F1)
(6H1R9F1)
(6K2R3F1)
(6K1R3F1)
(6M2R3F1)
(6M1R3F1)
(6M2R4F1)
(6M1R4F1)
(6P2R4F1)
(6P1R4F1)
(6F2L9F1)
(6F1L9F1)
(6H2L9F1)
(6H1L9F1)
(6K2L3F1)
(6K1L3F1)
(6M2L3F1)
(6M1L3F1)
(6M2L4F1)
(6M1L4F1)
(6P2L4F1)
(6P1L4F1)
(6H2R9G1)
(6H1R9G1)
(6K2R3G1)
(6K1R3G1)
(6M2R3G1)
(6M1R3G1)
(6M2R4G1)
(6M1R4G1)
(6P2R4G1)
(6P1R4G1)
GYARUS12K90A-F06
GYARUS12Q90A-F06
GYARUS16K90B-F06
GYARUS16R90B-F06
GYDRUS20L90C-M20L
GYDRUS20S90C-M20L
GYDRUS24M90D-M20L
GYDRUS24T90D-M20L
GYDRUS24M90D-M25L
GYDRUS24T90D-M25L
GYDRUS32P90F-M25L
GYDRUS32T90F-M25L
GYALUS12K90A-F06
GYALUS12Q90A-F06
GYALUS16K90B-F06
GYALUS16R90B-F06
GYDLUS20L90C-M20R
GYDLUS20S90C-M20R
GYDLUS24M90D-M20R
GYDLUS24T90D-M20R
GYDLUS24M90D-M25R
GYDLUS24T90D-M25R
GYDLUS32P90F-M25R
GYDLUS32T90F-M25R
GYARUS16K90B-G07
GYARUS16R90B-G07
GYDRUS20L90C-M20L
GYDRUS20S90C-M20L
GYDRUS24M90D-M20L
GYDRUS24T90D-M20L
GYDRUS24M90D-M25L
GYDRUS24T90D-M25L
GYDRUS32P90F-M25L
GYDRUS32T90F-M25L
(6H2L9G1)
(6H1L9G1)
(6K2L3G1)
(6K1L3G1)
(6M2L3G1)
(6M1L3G1)
(6M2L4G1)
(6M1L4G1)
(6P2L4G1)
(6P1L4G1)
GYALUS16K90B-G07
GYALUS16R90B-G07
GYDLUS20L90C-M20R
GYDLUS20S90C-M20R
GYDLUS24M90D-M20R
GYDLUS24T90D-M20R
GYDLUS24M90D-M25R
GYDLUS24T90D-M25R
GYDLUS32P90F-M25R
GYDLUS32T90F-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Modular Blade
Stock
GYM20LA-F10
GYM20LA-F10
GYM25LA-F12
GYM25LA-F12
GYM20RA-F10
GYM20RA-F10
GYM25RA-F12
GYM25RA-F12
GYM20LA-G12
GYM20LA-G12
GYM25LA-G14
GYM25LA-G14
GYM20RA-G12
GYM20RA-G12
GYM25RA-G14
GYM25RA-G14
The maximum groove depth varies according to the cutting diameter D1. For details, please refer to page F146.
*21 Dimensions
shown are when the gauge insert is used. If other insert geometries are used then L1, L3, F1 and F2 values may vary.

SPARE PARTS

90
F1
z
L3
L1
GYAR/LUS12 o90A- ooo

90
Wrench
GY05016S
(Clamp Torque
: 40 lbf-in)
TKY20R
TS407
(Clamp Torque
: 31 lbf-in)
TS55
(Clamp Torque
: 44 lbf-in)
zTKY30R
xTKY15D
F1
Fig. 3

(Clamp Torque
: 53 lbf-in)
F2
ar
L3
L1

Dimensions (inch)
*2
(4 pcs.)
H1
D4
zTKY30R
xTKY25D
Insert
Fig.
D4
L1
L3
F1
F2
H1
.750
.750
1.000
1.000
1.250
1.250
1.500
1.500
1.500
1.500
2.000
2.000
.750
.750
1.000
1.000
1.250
1.250
1.500
1.500
1.500
1.500
2.000
2.000
1.000
1.000
1.250
1.250
1.500
1.500
1.500
1.500
2.000
2.000
5.000
7.000
5.000
8.000
5.500
10.000
6.000
12.000
6.000
12.000
6.750
12.000
5.000
7.000
5.000
8.000
5.500
10.000
6.000
12.000
6.000
12.000
6.750
12.000
5.000
8.000
5.500
10.000
6.000
12.000
6.000
12.000
6.750
12.000
1.250
1.250
1.500
1.500
2.000
2.000
2.500
2.500
2.500
2.500
3.250
3.250
1.250
1.250
1.500
1.500
2.000
2.000
2.500
2.500
2.500
2.500
3.250
3.250
1.500
1.500
2.000
2.000
2.500
2.500
2.500
2.500
3.250
3.250
.605
.605
.730
.730
.875
.875
1.125
1.125
1.125
1.125
1.250
1.250
.605
.605
.730
.730
.875
.875
1.125
1.125
1.125
1.125
1.250
1.250
.730
.730
.875
.875
1.125
1.125
1.125
1.125
1.250
1.250
.230
.230
.230
.230
.250
.250
.375
.375
.375
.375
.250
.250
.230
.230
.230
.230
.250
.250
.375
.375
.375
.375
.250
.250
.230
.230
.250
.250
.375
.375
.375
.375
.250
.250
.671
.671
.921
.921
1.171
1.171
1.382
1.382
1.382
1.382
1.882
1.882
.671
.671
.921
.921
1.171
1.171
1.382
1.382
1.382
1.382
1.882
1.882
.921
.921
1.171
1.171
1.382
1.382
1.382
1.382
1.882
1.882
1
2
1
2
3
4
3
4
3
4
3
4
1
2
1
2
3
4
3
4
3
4
3
4
1
2
3
4
3
4
3
4
3
4
1.000
1.000
1.250
1.250
1.500
1.500
1.500
1.500
2.000
2.000
5.000
8.000
5.500
10.000
6.000
12.000
6.000
12.000
6.750
12.000
1.500
1.500
2.000
2.000
2.500
2.500
2.500
2.500
3.250
3.250
.730
.730
.875
.875
1.125
1.125
1.125
1.125
1.250
1.250
.230
.230
.250
.250
.375
.375
.375
.375
.250
.250
.921
.921
1.171
1.171
1.382
1.382
1.382
1.382
1.882
1.882
1
2
3
4
3
4
3
4
3
4
Cutting Mode
Page
GY2M0300F020N-GS
GY2M0318F020N-GS
GROOVING
Fig. 4
F2
ar
D1
GY2M0300F030N-GM
(Gauge insert)
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
F012
F013
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS
GY2M0400G030N-GU
GY2M0400G020N-GS
GY2M0400G030N-GM
(Gauge insert)
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS
*3 The maximum groove depth (ar) is a value within the dimension L3.
F137
GROOVING SYSTEM

5-1
GS
ar
D1
Fig. 2
F2
F1
90
L3
F2
ar
F1
90
Fig. 1
L3
Seat
Size
Insert
Width
W3
(inch)
Max.
Hand Groove Depth
ar
3
(R/L)
(inch)
.276
GROOVING
.197 .453
.187
.197
*
.236 .453
*1
.315 .512
*1
.295 .512
*1
.197 .453
1.625
2.000
2.500
2.750
1.250
1
*
.236 .453
*1
.315 .512
*1
.295 .512
*1
.315 .512
Min.Cutting
Diameter
D1
(inch)
1.250
.276
H1
D4
L1
*
.295 .512
*1
1.625
2.000
2.500
2.750
2.500
2.750
L1
Order Number
ID
Stock
(6H2R9H1)
(6H1R9H1)
(6K2R3H1)
(6K1R3H1)
(6M2R3H1)
(6M1R3H1)
(6M2R4H1)
(6M1R4H1)
(6P2R4H1)
(6P1R4H1)
GYARUS16K90B-H07
GYARUS16R90B-H07
GYDRUS20L90C-M20L
GYDRUS20S90C-M20L
GYDRUS24M90D-M20L
GYDRUS24T90D-M20L
GYDRUS24M90D-M25L
GYDRUS24T90D-M25L
GYDRUS32P90F-M25L
GYDRUS32T90F-M25L
(6H2L9H1)
(6H1L9H1)
(6K2L3H1)
(6K1L3H1)
(6M2L3H1)
(6M1L3H1)
(6M2L4H1)
(6M1L4H1)
(6P2L4H1)
(6P1L4H1)
GYALUS16K90B-H07
GYALUS16R90B-H07
GYDLUS20L90C-M20R
GYDLUS20S90C-M20R
GYDLUS24M90D-M20R
GYDLUS24T90D-M20R
GYDLUS24M90D-M25R
GYDLUS24T90D-M25R
GYDLUS32P90F-M25R
GYDLUS32T90F-M25R
(6M2R4J1)
(6M1R4J1)
(6P2R4J1)
(6P1R4J1)
GYDRUS24M90D-M25L
GYDRUS24T90D-M25L
GYDRUS32P90F-M25L
GYDRUS32T90F-M25L
(6M2L4J1)
(6M1L4J1)
(6P2L4J1)
(6P1L4J1)
GYDLUS24M90D-M25R
GYDLUS24T90D-M25R
GYDLUS32P90F-M25R
GYDLUS32T90F-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Modular Blade
Stock
GYM20LA-H12
GYM20LA-H12
GYM25LA-H14
GYM25LA-H14
GYM20RA-H12
GYM20RA-H12
GYM25RA-H14
GYM25RA-H14
GYM25LA-J14
GYM25LA-J14
GYM25RA-J14
GYM25RA-J14
.236
.250
.315 .512
*
.295 .512
*1
2.500
2.750
a
a
a
F138
*21 Dimensions

SPARE PARTS

90
F1
z
L3
L1

90
Wrench
GY05016S
(Clamp Torque
: 40 lbf-in)
TKY20R
TS407
(Clamp Torque
: 31 lbf-in)
TS55
(Clamp Torque
: 44 lbf-in)
zTKY30R
xTKY15D
F1
Fig. 3

(Clamp Torque
: 53 lbf-in)
F2
ar
L3
L1

Dimensions (inch)
*2
(4 pcs.)
H1
D4
zTKY30R
xTKY25D
Insert
Fig.
D4
L1
L3
F1
F2
H1
1.000
1.000
1.250
1.250
1.500
1.500
1.500
1.500
2.000
2.000
5.000
8.000
5.500
10.000
6.000
12.000
6.000
12.000
6.750
12.000
1.500
1.500
2.000
2.000
2.500
2.500
2.500
2.500
3.250
3.250
.730
.730
.875
.875
1.125
1.125
1.125
1.125
1.250
1.250
.230
.230
.250
.250
.375
.375
.375
.375
.250
.250
.921
.921
1.171
1.171
1.382
1.382
1.382
1.382
1.882
1.882
1
2
3
4
3
4
3
4
3
4
1.000
1.000
1.250
1.250
1.500
1.500
1.500
1.500
2.000
2.000
5.000
8.000
5.500
10.000
6.000
12.000
6.000
12.000
6.750
12.000
1.500
1.500
2.000
2.000
2.500
2.500
2.500
2.500
3.250
3.250
.730
.730
.875
.875
1.125
1.125
1.125
1.125
1.250
1.250
.230
.230
.250
.250
.375
.375
.375
.375
.250
.250
.921
.921
1.171
1.171
1.382
1.382
1.382
1.382
1.882
1.882
1
2
3
4
3
4
3
4
3
4
1.500 6.000 2.500 1.125

1.500 12.000 2.500 1.125
2.000 6.750 3.250 1.250
2.000 12.000 3.250 1.250
.375
.375
.250
.250
1.382
1.382
1.882
1.882
3
4
3
4
Cutting Mode
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Fig. 4
F2
ar
D1
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
(Gauge insert)
GY2M0500H040R05-GM
GY2M0500H040L05-GM
GY2M0500H040N-MS
GY2M0500H080N-MS
F012
F013
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS
GY2M0600J040N-GU
GY2M0635J040N-GU
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
(Gauge insert)
1.500 6.000 2.500 1.125

1.500 12.000 2.500 1.125
2.000 6.750 3.250 1.250
2.000 12.000 3.250 1.250
.375
.375
.250
.250
1.382
1.382
1.882
1.882
3
4
3
4
GY2M0635J040N-GM
F012
F013
GY2M0600J040N-MS
GY2M0600J080N-MS
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM
F139
GROOVING SYSTEM

Insert GY2Mooooooooo-GS
GS
90
ar
D1
Fig. 2
F2
F1
5-2
L3
H1
D4
L1
F2
ar
F1
90
Fig. 1
L3
Seat
Size
Insert
Width
W3
(mm)
Max.
Hand Groove Depth
ar
3
(R/L)
(mm)
GROOVING
Order Number
ID
(6E2R9D1)
(6E1R9D1)
(6G2R9D1)
(6G1R9D1)
(6J2R3D1)
(6J1R3D1)
(6L2R3D1)
(6L1R3D1)
(6L2R4D1)
(6L1R4D1)
(6N2R4D1)
(6N1R4D1)
(6E2L9D1)
(6E1L9D1)
(6G2L9D1)
(6G1L9D1)
(6J2L3D1)
(6J1L3D1)
(6L2L3D1)
(6L1L3D1)
(6L2L4D1)
(6L1L4D1)
(6N2L4D1)
(6N1L4D1)
(6E2R9E1)
(6E1R9E1)
(6G2R9E1)
(6G1R9E1)
(6J2R3E1)
(6J1R3E1)
(6L2R3E1)
(6L1R3E1)
(6L2R4E1)
(6L1R4E1)
(6N2R4E1)
(6N1R4E1)
(6E2L9E1)
(6E1L9E1)
(6G2L9E1)
(6G1L9E1)
(6J2L3E1)
(6J1L3E1)
(6L2L3E1)
(6L1L3E1)
(6L2L4E1)
(6L1L4E1)
(6N2L4E1)
(6N1L4E1)
Stock
Modular Blade
a
GYAR20K90A-D06

a
GYAR20Q90A-D06
a
GYAR25K90B-D06
6
32

a
GYAR25R90B-D06
a
GYDR32L90C-M20L
4 9.5
40
GYM20LA-D10
a
GYDR32S90C-M20L
1
R
a
GYDR40M90D-M20L
5.5 9.5
50
GYM20LA-D10
a
GYDR40T90D-M20L
1
a
GYDR40M90D-M25L
7 11.5
60
GYM25LA-D12
a
GYDR40T90D-M25L
1
a
GYDR50P90F-M25L
7 11.5
70
GYM25LA-D12
a
GYDR50T90F-M25L
1
D
2.00
a
GYAL20K90A-D06
6
25

a
GYAL20Q90A-D06
a
GYAL25K90B-D06
6
32

a
GYAL25R90B-D06
a
GYDL32L90C-M20R
4 9.5
40
GYM20RA-D10
a
GYDL32S90C-M20R
1
L
a
GYDL40M90D-M20R
5.5 9.5
50
GYM20RA-D10
a
GYDL40T90D-M20R
1
a
GYDL40M90D-M25R
7 11.5
60
GYM25RA-D12
a
GYDL40T90D-M25R
1
a
GYDL50P90F-M25R
7 11.5
70
GYM25RA-D12
a
GYDL50T90F-M25R
1
a
GYAR20K90A-E06
6
25

a
GYAR20Q90A-E06
a
GYAR25K90B-E06
6
32

a
GYAR25R90B-E06
a
GYDR32L90C-M20L
4 9.5
40
GYM20LA-E10
a
GYDR32S90C-M20L
1
R
a
GYDR40M90D-M20L
5.5 9.5
50
GYM20LA-E10
a
GYDR40T90D-M20L
1
a
GYDR40M90D-M25L
7 11.5
60
GYM25LA-E12
a
GYDR40T90D-M25L
1
a
GYDR50P90F-M25L
7 11.5
70
GYM25LA-E12
2.39
a
GYDR50T90F-M25L
1
E
a
GYAL20K90A-E06
2.50
6
25

a
GYAL20Q90A-E06
a
GYAL25K90B-E06
6
32

a
GYAL25R90B-E06
a
GYDL32L90C-M20R
4 9.5
40
GYM20RA-E10
a
GYDL32S90C-M20R
1
L
a
GYDL40M90D-M20R
5.5 9.5
50
GYM20RA-E10
a
GYDL40T90D-M20R
1
a
GYDL40M90D-M25R
7 11.5
60
GYM25RA-E12
a
GYDL40T90D-M25R
1
a
GYDL50P90F-M25R
7 11.5
70
GYM25RA-E12
a
GYDL50T90F-M25R
1
1 The maximum groove depth varies according to the cutting diameter D1. For details, please refer to page F146.
2 Dimensions shown are when the gauge insert is used. If other insert geometries are used then L1, L3, F1 and F2 values may vary.
25
*
*
*
*
*
*
*
*
*
*
*
*
F140
Min.Cutting
Diameter
D1
(mm)
L1
*
*
*
*
*
Stock

a
a
a
a

a
a
a
a

a
a
a
a

a
a
a
a

SPARE PARTS
90
z
F1
L3
L1
GYAR/L20 o90A- o06

GYAR/L25 o90B- o06
90
L1

Dimensions (mm)
L1
Wrench
GY05016S
(Clamp Torque
: 40 lbf-in)
TKY20R
TS407
(Clamp Torque
: 31 lbf-in)
TS55
(Clamp Torque
: 44 lbf-in)
zTKY30R
xTKY15D
GYDR/L40 o90D-M20L/R GY06013M

(Clamp Torque
GYDR/L40 o90D-M25L/R : 53 lbf-in)
F2
ar
L3
D4
GYDR/L32 o90C-M20L/R
F1
Fig. 3
L3
F1
*2
F2
(4 pcs.)
H1
D4
GYDR/L50 o90F-M25L/R
zTKY30R
xTKY25D
Insert
Fig.
Cutting Mode
H1
20
125
30
14.5
4.5
18
1
20
180
30
14.5
4.5
18
2
25
125
40
19
6.5
23
1
25
200
40
19
6.5
23
2
32
140
50
22
6.0
30
3
32
250
50
22
6.0
30
4
40
150
60
28
8.0
37
3
40
300
60
28
8.0
37
4
40
150
60
28
8.0
37
3
40
300
60
28
8.0
37
4
50
170
80
34
9.0
47
3
50
300
80
34
9.0
47
4
20
125
30
14.5
4.5
18
1
20
180
30
14.5
4.5
18
2
25
125
40
19
6.5
23
1
25
200
40
19
6.5
23
2
32
140
50
22
6.0
30
3
32
250
50
22
6.0
30
4
40
150
60
28
8.0
37
3
40
300
60
28
8.0
37
4
40
150
60
28
8.0
37
3
40
300
60
28
8.0
37
4
50
170
80
34
9.0
47
3
50
300
80
34
9.0
47
4
20
125
30
14.5
4.5
18
1
20
180
30
14.5
4.5
18
2
25
125
40
19
6.5
23
1
25
200
40
19
6.5
23
2
32
140
50
22
6.0
30
3
32
250
50
22
6.0
30
4
40
150
60
28
8.0
37
3
40
300
60
28
8.0
37
4
40
150
60
28
8.0
37
3
40
300
60
28
8.0
37
4
50
170
80
34
9.0
47
3
50
300
80
34
9.0
47
4
20
125
30
14.5
4.5
18
1
20
180
30
14.5
4.5
18
2
25
125
40
19
6.5
23
1
25
200
40
19
6.5
23
2
32
140
50
22
6.0
30
3
32
250
50
22
6.0
30
4
40
150
60
28
8.0
37
3
40
300
60
28
8.0
37
4
40
150
60
28
8.0
37
3
40
300
60
28
8.0
37
4
50
170
80
34
9.0
47
3
50
300
80
34
9.0
47
4
3 The maximum groove depth (ar) is a value within the dimension L3.
Page
GROOVING
Fig. 4
F2
ar
D1
GY2M0200D020N-GS
GY2M0200D020N-GM
(Gauge insert)
GY2M0200D020R05-GM
GY2M0200D020L05-GM
F012
F013
GY2M0200D020N-MM
GY2M0200D100N-BM
GY1G0200D020N-GFGS
GY2M0239E020N-GS
GY2M0250E020N-GS
GY2M0239E020N-GM
GY2M0250E020N-GM
(Gauge insert)
GY2M0250E020R05-GM
GY2M0250E020L05-GM
F012
F013
GY2M0250E020N-MM
GY2M0250E125N-BM
GY1G0239E020N-GFGS
GY1G0250E020N-GFGS
F141
GROOVING SYSTEM

5-2
GS
ar
D1
Fig. 2
F2
F1
90
L3
F2
ar
F1
90
Fig. 1
L3
Insert
Width
W3
(mm)
GROOVING
Seat
Size
Max.
Hand Groove Depth
ar
3
(R/L)
(mm)
3.00
3.18
25
32
1
*
5.5 9.5
*1
7 11.5
*1
7 11.5
*1
70
32
1
*
5.5 9.5
*1
7 11.5
*1
7 11.5
*1
40
50
60
70
32
40
*1
6 11.5
*1
7.5 13
*1
7.5 13
*1
60
32
50
70
4.00
4.5 11.5
F142
60
4.5 11.5
50
25
40
4 9.5
Min.Cutting
Diameter
D1
(mm)
4 9.5
H1
D4
L1
*1
6 11.5
*1
7.5 13
*1
7.5 13
*1
40
50
60
70
L1
Order Number
ID
Stock
(6E2R9F1)
(6E1R9F1)
(6G2R9F1)
(6G1R9F1)
(6J2R3F1)
(6J1R3F1)
(6L2R3F1)
(6L1R3F1)
(6L2R4F1)
(6L1R4F1)
(6N2R4F1)
(6N1R4F1)
(6E2L9F1)
(6E1L9F1)
(6G2L9F1)
(6G1L9F1)
(6J2L3F1)
(6J1L3F1)
(6L2L3F1)
(6L1L3F1)
(6L2L4F1)
(6L1L4F1)
(6N2L4F1)
(6N1L4F1)
(6G2R9G1)
(6G1R9G1)
(6J2R3G1)
(6J1R3G1)
(6L2R3G1)
(6L1R3G1)
(6L2R4G1)
(6L1R4G1)
(6N2R4G1)
(6N1R4G1)
GYAR20K90A-F06
GYAR20Q90A-F06
GYAR25K90B-F06
GYAR25R90B-F06
GYDR32L90C-M20L
GYDR32S90C-M20L
GYDR40M90D-M20L
GYDR40T90D-M20L
GYDR40M90D-M25L
GYDR40T90D-M25L
GYDR50P90F-M25L
GYDR50T90F-M25L
GYAL20K90A-F06
GYAL20Q90A-F06
GYAL25K90B-F06
GYAL25R90B-F06
GYDL32L90C-M20R
GYDL32S90C-M20R
GYDL40M90D-M20R
GYDL40T90D-M20R
GYDL40M90D-M25R
GYDL40T90D-M25R
GYDL50P90F-M25R
GYDL50T90F-M25R
GYAR25K90B-G07
GYAR25R90B-G07
GYDR32L90C-M20L
GYDR32S90C-M20L
GYDR40M90D-M20L
GYDR40T90D-M20L
GYDR40M90D-M25L
GYDR40T90D-M25L
GYDR50P90F-M25L
GYDR50T90F-M25L
(6G2L9G1)
(6G1L9G1)
(6J2L3G1)
(6J1L3G1)
(6L2L3G1)
(6L1L3G1)
(6L2L4G1)
(6L1L4G1)
(6N2L4G1)
(6N1L4G1)
GYAL25K90B-G07
GYAL25R90B-G07
GYDL32L90C-M20R
GYDL32S90C-M20R
GYDL40M90D-M20R
GYDL40T90D-M20R
GYDL40M90D-M25R
GYDL40T90D-M25R
GYDL50P90F-M25R
GYDL50T90F-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Modular Blade
Stock
GYM20LA-F10
GYM20LA-F10
GYM25LA-F12
GYM25LA-F12
GYM20RA-F10
GYM20RA-F10
GYM25RA-F12
GYM25RA-F12
GYM20LA-G12
GYM20LA-G12
GYM25LA-G14
GYM25LA-G14
GYM20RA-G12
GYM20RA-G12
GYM25RA-G14
GYM25RA-G14
*21 Dimensions

SPARE PARTS

90
z
F1
L3
L1
GYAR/L20 o90A-F06
GYAR/L25 o90B- ooo
90
Wrench
GY05016S
(Clamp Torque
: 40 lbf-in)
TKY20R
TS407
(Clamp Torque
: 31 lbf-in)
TS55
(Clamp Torque
: 44 lbf-in)
zTKY30R
xTKY15D
F1
Fig. 3

(Clamp Torque
GYDR/L40 o90D-M25L/R
: 53 lbf-in)
F2
ar
L3
L1

Dimensions (mm)
*2
(4 pcs.)
H1
D4
zTKY30R
xTKY25D
Insert
Fig.
D4
L1
L3
F1
F2
H1
20
20
25
25
32
32
40
40
40
40
50
50
20
20
25
25
32
32
40
40
40
40
50
50
25
25
32
32
40
40
40
40
50
50
125
180
125
200
140
250
150
300
150
300
170
300
125
180
125
200
140
250
150
300
150
300
170
300
125
200
140
250
150
300
150
300
170
300
30
30
40
40
50
50
60
60
60
60
80
80
30
30
40
40
50
50
60
60
60
60
80
80
40
40
50
50
60
60
60
60
80
80
14.5
14.5
19
19
22
22
28
28
28
28
34
34
14.5
14.5
19
19
22
22
28
28
28
28
34
34
19
19
22
22
28
28
28
28
34
34
4.5
4.5
6.5
6.5
6.0
6.0
8.0
8.0
8.0
8.0
9.0
9.0
4.5
4.5
6.5
6.5
6.0
6.0
8.0
8.0
8.0
8.0
9.0
9.0
6.5
6.5
6.0
6.0
8.0
8.0
8.0
8.0
9.0
9.0
18
18
23
23
30
30
37
37
37
37
47
47
18
18
23
23
30
30
37
37
37
37
47
47
23
23
30
30
37
37
37
37
47
47
1
2
1
2
3
4
3
4
3
4
3
4
1
2
1
2
3
4
3
4
3
4
3
4
1
2
3
4
3
4
3
4
3
4
25
25
32
32
40
40
40
40
50
50
125
200
140
250
150
300
150
300
170
300
40
40
50
50
60
60
60
60
80
80
19
19
22
22
28
28
28
28
34
34
6.5
6.5
6.0
6.0
8.0
8.0
8.0
8.0
9.0
9.0
23
23
30
30
37
37
37
37
47
47
1
2
3
4
3
4
3
4
3
4
Cutting Mode
Page
GY2M0300F020N-GS
GY2M0318F020N-GS
GROOVING
Fig. 4
F2
ar
D1
GY2M0300F030N-GM
(Gauge insert)
GY2M0318F030N-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0300F020N-MS
GY2M0300F040N-MS
F012
F013
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS
GY2M0400G030N-GU
GY2M0400G020N-GS
GY2M0400G030N-GM
(Gauge insert)
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0400G020N-MS
GY2M0400G040N-MS
F012
F013
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0400G200N-BM
GY1G0400G020N-GFGS
F143
GROOVING SYSTEM

5-2
GS
ar
D1
Fig. 2
F2
F1
90
L3
F2
ar
F1
90
Fig. 1
L3
Seat
Size
Insert
Width
W3
(mm)
Max.
Hand Groove Depth
ar
3
(R/L)
(mm)
GROOVING
4.5 11.5
4.75
5.00
*
6 11.5
*1
7.5 13
*1
7.5 13
*1
4.5 11.5
Min.Cutting
Diameter
D1
(mm)
32
H1
D4
L1
40
50
60
70
32
1
40
*
6 11.5
*1
7.5 13
*1
7.5 13
*1
60
7.5 13
60
7.5 13
*
*1
50
70
70
L1
Order Number
ID
Stock
(6G2R9H1)
(6G1R9H1)
(6J2R3H1)
(6J1R3H1)
(6L2R3H1)
(6L1R3H1)
(6L2R4H1)
(6L1R4H1)
(6N2R4H1)
(6N1R4H1)
GYAR25K90B-H07
GYAR25R90B-H07
GYDR32L90C-M20L
GYDR32S90C-M20L
GYDR40M90D-M20L
GYDR40T90D-M20L
GYDR40M90D-M25L
GYDR40T90D-M25L
GYDR50P90F-M25L
GYDR50T90F-M25L
(6G2L9H1)
(6G1L9H1)
(6J2L3H1)
(6J1L3H1)
(6L2L3H1)
(6L1L3H1)
(6L2L4H1)
(6L1L4H1)
(6N2L4H1)
(6N1L4H1)
GYAL25K90B-H07
GYAL25R90B-H07
GYDL32L90C-M20R
GYDL32S90C-M20R
GYDL40M90D-M20R
GYDL40T90D-M20R
GYDL40M90D-M25R
GYDL40T90D-M25R
GYDL50P90F-M25R
GYDL50T90F-M25R
(6L2R4J1)
(6L1R4J1)
(6N2R4J1)
(6N1R4J1)
GYDR40M90D-M25L
GYDR40T90D-M25L
GYDR50P90F-M25L
GYDR50T90F-M25L
(6L2L4J1)
(6L1L4J1)
(6N2L4J1)
(6N1L4J1)
GYDL40M90D-M25R
GYDL40T90D-M25R
GYDL50P90F-M25R
GYDL50T90F-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Modular Blade
Stock
GYM20LA-H12
GYM20LA-H12
GYM25LA-H14
GYM25LA-H14
GYM20RA-H12
GYM20RA-H12
GYM25RA-H14
GYM25RA-H14
GYM25LA-J14
GYM25LA-J14
GYM25RA-J14
GYM25RA-J14
6.00
6.35
7.5 13
7.5 13
*
*1
60
70
a
a
a
F144
*21 Dimensions

SPARE PARTS

90
z
F1
L3
L1
GYAR/L25 o90B-H07
90
Wrench
GY05016S
(Clamp Torque
: 40 lbf-in)
TKY20R
TS407
(Clamp Torque
: 31 lbf-in)
TS55
(Clamp Torque
: 44 lbf-in)
zTKY30R
xTKY15D
F1
Fig. 3

(Clamp Torque
GYDR/L40 o90D-M25L/R : 53 lbf-in)
F2
ar
L3
L1

Dimensions (mm)
*2
(4 pcs.)
H1
D4
zTKY30R
xTKY25D
Insert
Fig.
D4
L1
L3
F1
F2
H1
25
25
32
32
40
40
40
40
50
50
125
200
140
250
150
300
150
300
170
300
40
40
50
50
60
60
60
60
80
80
19
19
22
22
28
28
28
28
34
34
6.5
6.5
6.0
6.0
8.0
8.0
8.0
8.0
9.0
9.0
23
23
30
30
37
37
37
37
47
47
1
2
3
4
3
4
3
4
3
4
25
25
32
32
40
40
40
40
50
50
125
200
140
250
150
300
150
300
170
300
40
40
50
50
60
60
60
60
80
80
19
19
22
22
28
28
28
28
34
34
6.5
6.5
6.0
6.0
8.0
8.0
8.0
8.0
9.0
9.0
23
23
30
30
37
37
37
37
47
47
1
2
3
4
3
4
3
4
3
4
40
40
50
50
150
300
170
300
60
60
80
80
28
28
34
34
8.0
8.0
9.0
9.0
37
37
47
47
3
4
3
4
Cutting Mode
Page
GY2M0475H040N-GU
GY2M0500H040N-GU
GROOVING
Fig. 4
F2
ar
D1
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0475H040N-GM
GY2M0500H040N-GM
(Gauge insert)
GY2M0500H040R05-GM
GY2M0500H040L05-GM
GY2M0500H040N-MS
GY2M0500H080N-MS
F012
F013
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS
GY2M0600J040N-GU
GY2M0635J040N-GU
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0600J040N-GM
(Gauge insert)
GY2M0635J040N-GM
40
40
50
50
150
300
170
300
60
60
80
80
28
28
34
34
8.0
8.0
9.0
9.0
37
37
47
47
3
4
3
4
F012
F013
GY2M0600J040N-MS
GY2M0600J080N-MS
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0600J300N-BM
GY2M0635J318N-BM
F145
GROOVING SYSTEM
Recommended Cutting Conditions [Internal Grooving]
Grooving
105
2.000
(Note 1) The cutting diameter 100% represents the minimum cutting diameter (D1).
(Note 2) The graph on the left shows the cutting conditions when setting the feed to 100%.
100
1.500
Feed (%)
Shank Diameter D4 (inch)
: 1st recommended area
1.250
1.000
95
90
85
.750
80
0
.002
.004
.006
.008
100
150
200
250
Cutting Diameter (%)
Feed (inch/rev)
GROOVING
Traverse Machining (MM/MS Breaker)

a When traverse machining a blind hole, it is recommended to
carry out back turning considering chip disposal.
Insert width .236"
Insert width .197"
Insert width .157"
Insert width .118"
Insert width .098"

Insert width .079"
Feed (inch/rev)
(Note) The above cutting conditions are for when using the tool overhang (L) 1.6-2.0 times larger than the shank diameter (D4). (L/D=1.6-2.0)
When using L/D larger than 2.0, reduce the cutting conditions.
&D4
Tool chuck
Limitation of the Maximum Groove Depth
y INCH SHANK
The maximum groove depth is not limited by the cutting diameter.
When using the modular blade type

The maximum groove depth is limited by the cutting diameter.
Max. Groove Depth (inch)
Shank Diameter=1.250inch (GYM20 Blade)
When using the mono block type
.453
.433
GYM20L/RA-G12
GYM20L/RA-H12
.394
.374
.354
.315
.276
GYM20L/RA-D10
GYM20L/RA-E10
GYM20L/RA-F10
.236
.197
.157
1.625 1.875 2.125
1.750
2.500
3.125
3.500
4.000
Cutting Diameter (inch)
Due to interference of this part,

the maximum groove depth is
limited by the cutting diameter.

.453
.433
.315
GYM20L/RA-D10
GYM20L/RA-E10
GYM20L/RA-F10
.276
.236
.217
2.000 2.250
2.125 2.500
F146
GYM20L/RA-G12
GYM20L/RA-H12
.394
.374
.354
3.125
4.000 4.375
5.125

Work Material
Hardness
Insert Grade
165
VP20RT
Cutting Speed (SFM)

495
660
330
260
990
590
295
VP10RT
825
625
< 160HB
Mild Steel
360
MY5015
825
230
NX2525
VP20RT
560
195
460
230
VP10RT
495
160-280HB
295
MY5015
NX2525
Carbon Steel
Alloy Steel
VP20RT
180
440
165
360
195
VP10RT
690
395
> 280HB
260
MY5015
VP20RT
345
165
360
< 270HB
Stainless Steel
K
Tensile Strength
< 300MPa
Cast Iron
150
VP10RT
195
VP20RT
165
VP20RT
Tensile Strength
< 800MPa
165
Hardened steel
> 50HRC
VP10RT
MB8025
495
690
360
195
VP10RT
VP20RT

Titanium Alloy
460
295
395
260
MY5015
395
230
VP10RT
MY5015
Ductile Cast Iron
GROOVING
NX2525
525
525
100 195
130 230
195
330
y METRIC SHANK
.512
GYM25L/RA-G14
GYM25L/RA-H14
GYM25L/RA-J14
.472
.453
.433
.394
GYM25L/RA-D12
GYM25L/RA-E12
GYM25L/RA-F12
.354
.315
.276
2.500 2.750 3.125
3.750
5.000 5.250
.512
GYM25L/RA-G14
GYM25L/RA-H14
GYM25L/RA-J14
.394
.354
GYM25L/RA-D12
GYM25L/RA-E12
GYM25L/RA-F12
.315
.295
.276
2.750 3.125 3.750
5.000
6.250
3.000 3.375 4.000 4.500 Cutting Diameter
Cutting Diameter (mm)
Shank Diameter=40mm (GYM25 Blade)

Max. Groove Depth (mm)
.472
.453
.433


(inch)
F147
GROOVING SYSTEM
RECOMMENDATIONS FOR INTERNAL GROOVING

Holder
Tool chuck
Tool chuck
aWhen the overhang is the same, select a holder with the largest
possible shank size to ensure sufcient clamping rigidity.
Modular blade (2)
GROOVING
Modular blade (1)
GYM25R/L-oo
GYM20R/L-oo
aFor a 1.5" & 40mm shank holder, if there is no restriction
for use, select a holder suitable for GYM25 blade.

Over hang
L3
F2
Tool chuck
aThe maximum groove depth is limited to the dimension
L3. When machining with longer overhangs, refer to the

dimension F2 of the tool used.
F148
GYM20R/LA-oo
GYM20R/LA-D10
GYM20R/LA-E10
GYM20R/LA-F10
GYM20R/LA-G12
GYM20R/LA-H12
GYM25R/LA-oo
GYM25R/LA-D12
GYM25R/LA-E12
GYM25R/LA-F12
GYM25R/LA-G14
GYM25R/LA-H14
GYM25R/LA-J14
aFor an internal holder, select a modular blade listed above.
a Notes on multi-function machining (MS and MM breakers)

For internal grooving, the machining methods for external grooving (F049 050)
can be used, but please note the following precautions.
Machining blind holes
Coolant
aAs continuous chips tend to elongate at the back of the
aSupply large amounts of coolant for effective chip disposal
GROOVING
bore, the above operation is recommended.

The recommended width of cut for x is .020 inch.
during cutting. Maintain supply until the tool has been

retracted completely for improved chip disposal.
Machining Wide Grooves

Grooving
a When the insert width is x 2 groove width
a When the insert width is x 2 < groove width
Chips
Coolant
aWhen the depth of cut is shallower than the insert width,
continuous chips are usually produced. When plunging in

several passes, it is recommended to carry out machining in
the steps above. This ensures that coolant reaches the cutting
edge and chips are easily discharged.
aWhen the groove depth is larger than the insert width,
carry out plunging in the steps above to break up chips

efciently.
Turning
aWhen chip breaking and
disposal are especially

important, cross-feed
machining is recommended.
aWide face grooving when the corner R of the work piece is
equal to the corner R of the insert, machine as shown above.

(When corner R of the work piece is larger than corner R of
the insert, refer to the description of external wide grooving.)
aIf the groove depth exceeds a given level, chips may elongate at
the wall. In such a case, increase the feed and carry out
machining as shown above.
Machining instruction
aIt is recommended to carry out
grooving from the front end of

the workpiece. This reduces
workpiece deection.
F149
GROOVING SYSTEM
(a) Insert clamp screw x 1pc.
Modular Holder
Modular Blade
(b) Wrench
(d) Wrench
(Ex.)
Short,
Medium
(4 holes)
Insert
(c) Modular blade

set screw x 4pcs.
(Ex.)
(Ex.)
GROOVING
2 side
screws
Note 2)
blade set screws in order of
2 front
screws
Note 3)
Note 4)
Dont tighten the insert clamp screw
without installing the insert.
Good
Assembled
F150
NG
Note 5)
Ensure that the wrench is perpendicular to the screw tightening.
INSERT INSTALLATION
Holder
(a) Insert clamp screw x 1pc.
(b) Wrench
Insert
(Ex.)
(Ex.)
GROOVING
Note 1) z and x are changed by the insert size.
Note 2)
Please clean the insert-seat before installing the insert.
Note 3)
Dont tighten the insert clamp screw
without installing the insert.
Good
Assembled
NG
Note 4)
Ensure that the wrench is perpendicular to the screw tightening.
F151
GROOVING SYSTEM
CORRESPONDING TABLE OF HOLDERS/MODULAR BLADES

a External grooving / Cutting off / Copying (00 type/90 type holder)
a External grooving / Cutting off / Copying (00 type holder)

a Face grooving / Copying (00 type holder)
Modular Blade
Modular Blade
(Inch holder)
GYHLUS10B00-M20L
(Metric holder)
GYHL1616J00-M20L
(Inch holder)
GYHRUS12C00-M20R
GYHLUS12C90-M20R
(Metric holder)
GYHR2020K00-M20R
GYHL2020K90-M20R
(Inch holder)
GYHLUS12C00-M20L
GYHRUS12C90-M20L
(Metric holder)
GYHL2020K00-M20L
GYHR2020K90-M20L
For External Grooving
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM20RA-E06
GYM20RA-E10
GYM20RB-E18
GYM20RA-F06
GYM20RA-F10
GYM20RB-F18
GYM20RA-G12
.236
.394
.709
.236
.394
.709
.236
.394
.709
.472
GYM20RA-H12
.472
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM20LA-E06
GYM20LA-E10
GYM20LB-E18
GYM20LA-F06
GYM20LA-F10
GYM20LB-F18
GYM20LA-G12
.236
.394
.709
.236
.394
.709
.236
.394
.709
.472
GYM20LA-H12
.472
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM20RA-E06
GYM20RA-E10
GYM20RB-E18
GYM20RA-F06
GYM20RA-F10
GYM20RB-F18
GYM20RA-G12
.236
.394
.709
.236
.394
.709
.236
.394
.709
.472
GYM20RA-H12
.472
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM20LA-E06
GYM20LA-E10
GYM20LB-E18
GYM20LA-F06
GYM20LA-F10
GYM20LB-F18
GYM20LA-G12
.236
.394
.709
.236
.394
.709
.236
.394
.709
.472
GYM20LA-H12
.472
Modular Blade
Number
.079 F014
.094
.098
.118
.125
.157
.187
.197
F016
F018
F020
F022
F030
F032
F034
F036
F038
.079 F014
.094
.098
.118
.125
.157
.187
.197
.079
.094
.098
.118
.125
.157
.187
.197
F016
F018
F020
F022
F030
F032
F034
F036
F038
F014
.079 F016
.094
.098
.118
.125
.157
.187
.197
(Inch holder)
GYHRUS12C00-M25R
(Metric holder)
GYHR2020K00-M25R
F014
F016
F018
F020
F022
F026
F028
F030
F032
F034
F036
F038
F042
F044
F018
F020
F022
F026
F028
F030
F032
F034
F036
F038
F042
F044
Note) The modular blade number highlighted in red is also compatible

with internal holders.
F152
GROOVING
GYHR1616J00-M20R
(Metric holder)
GYHRUS10B00-M20R
(Inch holder)
Modular Blade
Number
For Face Grooving
Max. Insert
Groove Width Page
Depth (inch)
(inch)
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RD-F12-035
GYM25RD-F12-040
GYM25RD-F12-050
GYM25RD-F12-060
GYM25RD-F20-060
GYM25RD-F12-075
GYM25RD-F20-075
GYM25RD-F12-100
GYM25RD-F20-100
GYM25RD-F12-135
GYM25RD-F20-135
GYM25RD-F12-180
GYM25RD-F20-180
GYM25RD-G14-040
GYM25RD-G14-050
GYM25RD-G14-060
GYM25RD-G25-060
GYM25RD-G14-085
GYM25RD-G25-085
GYM25RD-G14-125
GYM25RD-G25-125
GYM25RD-G14-180
GYM25RD-G25-180
GYM25RD-G14-250
GYM25RD-G25-250
Max. Insert
Groove Width Page
Depth (inch)
(inch)
.236
.472
.787
.236
.472
.787
.236
.472
.787
.315
.551
.984
.315
.551
.984
.315
.551
.984
.472
.472
.472
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.551
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.079
F014
.094 F016
.098
.118
.125
.157
.187
.197
F018
F020
F022
F024
F030
F032
F034
F036
F038
F040
.236
.250
.118 F054
.125 F090
.157
F062
F098

Modular Blade
GYHRUS12C00-M25R
(Metric holder)
GYHR2020K00-M25R
For Face Grooving
(Inch holder)
Modular Blade
Number
(Inch holder)
GYHLUS12C00-M25L
(Metric holder)
For Face Grooving
GYHL2020K00-M25L
GYM25RD-H14-050
GYM25RD-H14-060
GYM25RD-H25-060
GYM25RD-H14-085
GYM25RD-H25-085
GYM25RD-H14-125
GYM25RD-H25-125
GYM25RD-H14-180
GYM25RD-H25-180
GYM25RD-H14-250
GYM25RD-H25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
GYM25RD-J25-250
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LD-F12-035
GYM25LD-F12-040
GYM25LD-F12-050
GYM25LD-F12-060
GYM25LD-F20-060
GYM25LD-F12-075
GYM25LD-F20-075
GYM25LD-F12-100
GYM25LD-F20-100
GYM25LD-F12-135
GYM25LD-F20-135
GYM25LD-F12-180
GYM25LD-F20-180
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.236
.472
.787
.236
.472
.787
.236
.472
.787
.315
.551
.984
.315
.551
.984
.315
.551
.984
.472
.472
.472
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
Modular Blade
Number
.187 F070
.197 F106
(Inch holder)
.236 F078
.250 F114
GYHLUS12C00-M25L
(Metric holder)
GYHL2020K00-M25L
.079
F014
.094
F016
.098
.118
.125
.157
.187
.197
F018
F020
F022
F024
F030
F032
F034
F036
F038
F040
For Face Grooving
Max. Insert
Groove Width Page
Depth (inch)
(inch)
GYM25LD-G14-040
GYM25LD-G14-050
GYM25LD-G14-060
GYM25LD-G25-060
GYM25LD-G14-085
GYM25LD-G25-085
GYM25LD-G14-125
GYM25LD-G25-125
GYM25LD-G14-180
GYM25LD-G25-180
GYM25LD-G14-250
GYM25LD-G25-250
GYM25LD-H14-050
GYM25LD-H14-060
GYM25LD-H25-060
GYM25LD-H14-085
GYM25LD-H25-085
GYM25LD-H14-125
GYM25LD-H25-125
GYM25LD-H14-180
GYM25LD-H25-180
GYM25LD-H14-250
GYM25LD-H25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
GYM25LD-J25-250
Max. Insert
Groove Width Page
Depth (inch)
(inch)
.551
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.157
F066
F102
GROOVING
Modular Blade
.187 F074
.197 F110
.236 F080
.250 F116
.236
.250
.118 F058
.125 F094

F153
GROOVING SYSTEM

a Face grooving / Copying (00 type/90 type holder)
Modular Blade
Modular Blade
(Inch holder)
GYHRUS16D00-M25R
GYHLUS16D90-M25R
(Metric holder)
For Face Grooving
GYHR2525M00-M25R
GYHL2525M90-M25R
.236
.472
.787
.236
.472
.787
.236
.472
.787
.315
.551
.984
.315
.551
.984
.315
.551
.984
.472
.472
.472
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.551
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.079 F014
.094
.098
.118
.125
.157
.187
.197
.236
.250
F016
F018
F020
F022
F024
F026
F028
F030
F032
F034
F036
F038
F040
F042
F044
(Inch holder)
GYHRUS16D00-M25R
GYHLUS16D90-M25R
(Metric holder)
GYHR2525M00-M25R
GYHL2525M90-M25R
F054
.118 F082
.125 F090
F118
(Inch holder)
GYHLUS16D00-M25L
GYHRUS16D90-M25L
F062
F084
.157
F098
F120

F154
Modular Blade
Number
For Face Grooving
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RD-F12-035
GYM25RD-F12-040
GYM25RD-F12-050
GYM25RD-F12-060
GYM25RD-F20-060
GYM25RD-F12-075
GYM25RD-F20-075
GYM25RD-F12-100
GYM25RD-F20-100
GYM25RD-F12-135
GYM25RD-F20-135
GYM25RD-F12-180
GYM25RD-F20-180
GYM25RD-G14-040
GYM25RD-G14-050
GYM25RD-G14-060
GYM25RD-G25-060
GYM25RD-G14-085
GYM25RD-G25-085
GYM25RD-G14-125
GYM25RD-G25-125
GYM25RD-G14-180
GYM25RD-G25-180
GYM25RD-G14-250
GYM25RD-G25-250
GROOVING
Modular Blade
Number
(Metric holder)
GYHL2525M00-M25L
GYHR2525M90-M25L
For Face Grooving
Max. Insert
Groove Width Page
Depth (inch)
(inch)
GYM25RD-H14-050
GYM25RD-H14-060
GYM25RD-H25-060
GYM25RD-H14-085
GYM25RD-H25-085
GYM25RD-H14-125
GYM25RD-H25-125
GYM25RD-H14-180
GYM25RD-H25-180
GYM25RD-H14-250
GYM25RD-H25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
GYM25RD-J25-250
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LD-F12-035
GYM25LD-F12-040
GYM25LD-F12-050
GYM25LD-F12-060
GYM25LD-F20-060
GYM25LD-F12-075
GYM25LD-F20-075
GYM25LD-F12-100
GYM25LD-F20-100
GYM25LD-F12-135
GYM25LD-F20-135
GYM25LD-F12-180
GYM25LD-F20-180
Max. Insert
Groove Width Page
Depth (inch)
(inch)
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.236
.472
.787
.236
.472
.787
.236
.472
.787
.315
.551
.984
.315
.551
.984
.315
.551
.984
.472
.472
.472
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
F070
.187 F086
.197 F106
F122
F078
.236 F088
.250 F114
F124
.079 F014
.094
.098
.118
.125
.157
.187
.197
.236
.250
F016
F018
F020
F022
F024
F026
F028
F030
F032
F034
F036
F038
F040
F042
F044
F058
.118 F082
.125 F094
F118

a Face grooving / Copying (00 type/90 type holder)
Modular Blade
Modular Blade
Number
GYHL2525M00-M25L
GYHR2525M90-M25L
(Inch holder)
GYHRUS20D00-M25R
(Metric holder)
GYHR3225P00-M25R
(Metric holder)
For Face Grooving
(Inch holder)
GYHLUS16D00-M25L
GYHRUS16D90-M25L
GYM25LD-G14-040
GYM25LD-G14-050
GYM25LD-G14-060
GYM25LD-G25-060
GYM25LD-G14-085
GYM25LD-G25-085
GYM25LD-G14-125
GYM25LD-G25-125
GYM25LD-G14-180
GYM25LD-G25-180
GYM25LD-G14-250
GYM25LD-G25-250
GYM25LD-H14-050
GYM25LD-H14-060
GYM25LD-H25-060
GYM25LD-H14-085
GYM25LD-H25-085
GYM25LD-H14-125
GYM25LD-H25-125
GYM25LD-H14-180
GYM25LD-H25-180
GYM25LD-H14-250
GYM25LD-H25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
GYM25LD-J25-250
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
.551
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.236
.472
.787
.236
.472
.787
.236
.472
.787
.315
.551
.984
.315
.551
.984
.315
.551
.984
Modular Blade
Number
F066
F084
.157
F102
F120
F074
.187 F086
.197 F110
F122
(Inch holder)
GYHRUS20D00-M25R
(Metric holder)
GYHR3225P00-M25R
F080
.236 F088
.250 F116
F124
.079
.094 F014
.098 F016
.118
.125
.157
.187
.197
F018
F020
F022
F024
F030
F032
F034
F036
F038
F040
For Face Grooving
Max. Insert
Groove Width Page
Depth (inch)
(inch)
GYM25RD-F12-035
GYM25RD-F12-040
GYM25RD-F12-050
GYM25RD-F12-060
GYM25RD-F20-060
GYM25RD-F12-075
GYM25RD-F20-075
GYM25RD-F12-100
GYM25RD-F20-100
GYM25RD-F12-135
GYM25RD-F20-135
GYM25RD-F12-180
GYM25RD-F20-180
GYM25RD-G14-040
GYM25RD-G14-050
GYM25RD-G14-060
GYM25RD-G25-060
GYM25RD-G14-085
GYM25RD-G25-085
GYM25RD-G14-125
GYM25RD-G25-125
GYM25RD-G14-180
GYM25RD-G25-180
GYM25RD-G14-250
GYM25RD-G25-250
GYM25RD-H14-050
GYM25RD-H14-060
GYM25RD-H25-060
GYM25RD-H14-085
GYM25RD-H25-085
GYM25RD-H14-125
GYM25RD-H25-125
GYM25RD-H14-180
GYM25RD-H25-180
GYM25RD-H14-250
GYM25RD-H25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
GYM25RD-J25-250
Max. Insert
Groove Width Page
Depth (inch)
(inch)
.472
.472
.472
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.551
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.118 F056
.125 F092
.157
F064
F100
GROOVING
Modular Blade
.187 F072
.197 F108
.236 F078
.250 F114
.236
.250
F155
GROOVING SYSTEM

Modular Blade
GROOVING
(Inch holder)
GYHLUS20D00-M25L
(Metric holder)
For Face Grooving
GYHL3225P00-M25L
F156
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LD-F12-035
GYM25LD-F12-040
GYM25LD-F12-050
GYM25LD-F12-060
GYM25LD-F20-060
GYM25LD-F12-075
GYM25LD-F20-075
GYM25LD-F12-100
GYM25LD-F20-100
GYM25LD-F12-135
GYM25LD-F20-135
GYM25LD-F12-180
GYM25LD-F20-180
GYM25LD-G14-040
GYM25LD-G14-050
GYM25LD-G14-060
GYM25LD-G25-060
GYM25LD-G14-085
GYM25LD-G25-085
GYM25LD-G14-125
GYM25LD-G25-125
GYM25LD-G14-180
GYM25LD-G25-180
GYM25LD-G14-250
GYM25LD-G25-250
GYM25LD-H14-050
GYM25LD-H14-060
GYM25LD-H25-060
GYM25LD-H14-085
GYM25LD-H25-085
GYM25LD-H14-125
GYM25LD-H25-125
GYM25LD-H14-180
GYM25LD-H25-180
GYM25LD-H14-250
GYM25LD-H25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
.236
.472
.787
.236
.472
.787
.236
.472
.787
.315
.551
.984
.315
.551
.984
.315
.551
.984
.472
.472
.472
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.551
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
GYM25LD-J25-250 .984
Modular Blade
Number
.079
.094 F014
.098 F016
Modular Blade
Number
F018
.118 F020
.125 F022
F024
.157 F030
F032
.187 F034
.197 F036
F038
.236 F040
.250
.118 F060
.125 F096
(Inch holder)
GYHRUS24E00-M25R
(Metric holder)
GYHR3232P00-M25R
F068
.157 F104
.187 F076
.197 F112
.236 F080
.250 F116
For Face Grooving
Modular Blade
Max. Insert
Groove Width Page
Depth (inch)
(inch)
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RD-F12-035
GYM25RD-F12-040
GYM25RD-F12-050
GYM25RD-F12-060
GYM25RD-F20-060
GYM25RD-F12-075
GYM25RD-F20-075
GYM25RD-F12-100
GYM25RD-F20-100
GYM25RD-F12-135
GYM25RD-F20-135
GYM25RD-F12-180
GYM25RD-F20-180
GYM25RD-G14-040
GYM25RD-G14-050
GYM25RD-G14-060
GYM25RD-G25-060
GYM25RD-G14-085
GYM25RD-G25-085
GYM25RD-G14-125
GYM25RD-G25-125
GYM25RD-G14-180
GYM25RD-G25-180
GYM25RD-G14-250
GYM25RD-G25-250
GYM25RD-H14-050
GYM25RD-H14-060
GYM25RD-H25-060
GYM25RD-H14-085
GYM25RD-H25-085
GYM25RD-H14-125
GYM25RD-H25-125
GYM25RD-H14-180
GYM25RD-H25-180
GYM25RD-H14-250
GYM25RD-H25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J25-070
GYM25RD-J14-110
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J25-170
GYM25RD-J14-250
Max. Insert
Groove Width Page
Depth (inch)
(inch)
.236
.472
.787
.236
.472
.787
.236
.472
.787
.315
.551
.984
.315
.551
.984
.315
.551
.984
.472
.472
.472
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.551
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
GYM25RD-J25-250 .984
.079
.094 F014
.098 F016
F018
.118 F020
.125 F022
F024
.157 F030
F032
.187 F034
.197 F036
F038
.236 F040
.250
.118 F056
.125 F092
F064
.157 F100
.187 F072
.197 F108
.236 F078
.250 F114

a Internal grooving / Copying (90 type holder)
Modular Blade
GYHLUS24E00-M25L
(Metric holder)
For Face Grooving
GYHL3232P00-M25L
(Inch holder)
.079
.094 F014
.098 F016
.118
.125
.157
.187
.197
.236
.250
F018
F020
F022
F024
F030
F032
F034
F036
F038
F040
GYDRUS20L90C-M20L
GYDRUS20S90C-M20L
(Metric holder)
GYDR32L90C-M20L
GYDR32S90C-M20L
(Inch holder)
GYDLUS20L90C-M20R
GYDLUS20S90C-M20R
(Metric holder)
GYDL32L90C-M20R
GYDL32S90C-M20R
(Inch holder)
GYDRUS24M90D-M20L
GYDRUS24T90D-M20L
(Metric holder)
.118 F060
.125 F096
GYDR40M90D-M20L
GYDR40T90D-M20L
(Inch holder)
GYDLUS24M90D-M20R
GYDLUS24T90D-M20R
(Metric holder)
GYDL40M90D-M20R
GYDL40T90D-M20R
GYDRUS24M90D-M25L
GYDRUS24T90D-M25L
GYDRUS32P90F-M25L
GYDRUS32T90F-M25L
(Metric holder)
GYDR40M90D-M25L
GYDR40T90D-M25L
GYDR50P90F-M25L
GYDR50T90F-M25L
.187 F076
.197 F112
(Metric holder)
GYDL40M90D-M25R
GYDL40T90D-M25R
GYDL50P90F-M25R
GYDL50T90F-M25R
GYM20LA-F10
GYM20LA-G12
GYM20LA-H12
GYM20RA-D10
GYM20RA-E10
GYM20RA-F10
GYM20RA-G12
GYM20RA-H12
GYM20LA-D10
GYM20LA-E10
GYM20LA-F10
GYM20LA-G12
GYM20LA-H12
GYM20RA-D10
GYM20RA-E10
GYM20RA-F10
GYM20RA-G12
GYM20RA-H12
GYM25LA-E12
GYM25LA-F12
GYM25LA-G14
GYM25LA-H14
GYM25LA-J14
GYM25RA-D12
(Inch holder)
GYDLUS24M90D-M25R
GYDLUS24T90D-M25R
GYDLUS32P90F-M25R
GYDLUS32T90F-M25R
GYM20LA-E10
GYM25LA-D12
(Inch holder)
F068
.157 F104
GYM20LA-D10
GYM25RA-E12
GYM25RA-F12
GYM25RA-G14
GYM25RA-H14
GYM25RA-J14
Max. Insert
Groove Width Page
Depth (inch)
(inch)
.157-.374 .079
.094
.157-.374
.098
.118
.157-.374
.125
.197-.453 .157
.187
.197-.453
.197
.157-.374 .079
.094
.157-.374
.098
.118
.157-.374
.125
.197-.453 .157
.187
.197-.453
.197
.217-.374 .079
.094
.217-.374
.098
.118
.217-.374
.125
.236-.453 .157
.187
.236-.453
.197
.217-.374 .079
.094
.217-.374
.098
.118
.217-.374
.125
.236-.453 .157
.187
.236-.453
.197
.276-.453 .079
.094
.276-.453
.098
.118
.276-.453
.125
.295-.512 .157
.187
.295-.512
.197
.236
.295-.512
.250
.276-.453 .079
.094
.276-.453
.098
.118
.276-.453
.125
.295-.512 .157
.187
.295-.512
.197
.236
.295-.512
.250
F134
F136
F138
F140
F142
F144
F134
F136
F138
F140
F142
F144
F134
F136
F138
F140
F142
F144
GROOVING
.236
.472
.787
.236
.472
.787
.236
.472
.787
.315
.551
.984
.315
.551
.984
.315
.551
.984
.472
.472
.472
.472
.787
.472
.787
.472
.787
.472
.787
.472
.787
.551
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
.551
.984
.551
.551
.984
.551
.984
.551
.984
.551
.984
For Internal Grooving For Internal Grooving For Internal Grooving For Internal Grooving
(Inch holder)
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LD-F12-035
GYM25LD-F12-040
GYM25LD-F12-050
GYM25LD-F12-060
GYM25LD-F20-060
GYM25LD-F12-075
GYM25LD-F20-075
GYM25LD-F12-100
GYM25LD-F20-100
GYM25LD-F12-135
GYM25LD-F20-135
GYM25LD-F12-180
GYM25LD-F20-180
GYM25LD-G14-040
GYM25LD-G14-050
GYM25LD-G14-060
GYM25LD-G25-060
GYM25LD-G14-085
GYM25LD-G25-085
GYM25LD-G14-125
GYM25LD-G25-125
GYM25LD-G14-180
GYM25LD-G25-180
GYM25LD-G14-250
GYM25LD-G25-250
GYM25LD-H14-050
GYM25LD-H14-060
GYM25LD-H25-060
GYM25LD-H14-085
GYM25LD-H25-085
GYM25LD-H14-125
GYM25LD-H25-125
GYM25LD-H14-180
GYM25LD-H25-180
GYM25LD-H14-250
GYM25LD-H25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J25-070
GYM25LD-J14-110
GYM25LD-J25-110
GYM25LD-J14-170
GYM25LD-J25-170
GYM25LD-J14-250
GYM25LD-J25-250
Modular Blade
Number
For Internal Grooving
Modular Blade
Number
For Internal Grooving
Modular Blade
Max. Insert
Groove Width Page
Depth (inch)
(inch)
F134
F136
F138
F140
F142
F144
F134
F136
F138
F140
F142
F144
F134
F136
F138
F140
F142
F144
.236 F080
.250 F116
F157
EXTERNAL GROOVING
UGHOLDER
UGHN
Order Number
a Strengthened insert clamping force.

a Block and blade type and solid type series.
a Groove width .087 .201inch.
External cutting off, Grooving
Stock Insert Number
Cutting Width
(inch)
W3
Max.
Cut off
Diameter
(inch)
Max.
Groove Depth
(inch)
Dimensions (inch)
Tool Block
H1
L1
H2
Wrench
2p
.087
1.970
.787
1.024
.063
4.331
.843
UGS1
263
3p
.122
2.950
1.280
1.024
.093
4.331
.843
UGS1
264
4p
.161
3.150
1.378
1.024
.126
4.331
.843
UGS1
265
5p
.201
3.150
1.378
1.024
.157
4.331
.843
UGS1
322
2p
.087
1.970
.787
1.260
.063
5.906
.984
UGS1
323
3p
.122
3.937
1.772
1.260
.093
5.906
.984
UGS1
324
4p
.161
3.937
1.772
1.260
.126
5.906
.984
UGS1
325
5p
.201
4.724
2.165
1.260
.157
5.906
.984
UGS1
GROOVING
UGHN262
KGT
KGBN26-19.05-30
KGBN26-25.40-30
KGBN32-19.05-30
KGBN32-25.40-30
TOOL BLOCK
Clamp Screw
Set Bolt
Clamp Bridge
Shank
Block
Spare Parts (Block)

Order Number
Dimensions (inch)
Stock
h1
h2
h3
l1
Block
Clamp Bridge Clamp Screw Wrench
Shank
Set Bolt
Wrench
KGBN26-19.05-30
.750 .750 .470 1.772 .750 1.656 KGBN26
KGC1
LS15T
TKY25R KGS19.05 HSC08016 HKY60R
26-25.40-30
1.000 1.000 .220 1.772 1.000 1.906 KGBN26
KGC1
LS15T
32-19.05-30
.750 .750 .652 2.047 .750 1.656 KGBN32
KGC1
LS15T
32-25.40-30
1.000 1.000 .402 2.047 1.000 1.906 KGBN32
KGC1
LS15T
(Note) When ordering a block, clamp bridge and clamp screw are included.
When ordering a shank, set bolts are included.
F158
Spare Parts (Shank)
INSERTS
4N
.122 (3.1mm) .008
.161 (4.1mm) .008
5N
.201 (5.1mm) .008
KGT2R
2L
.087 (2.2mm) .008
3R
.122 (3.1mm) .008
3L
.122 (3.1mm) .008
4R
4L
.161 (4.1mm) .008
5R
.201 (5.1mm) .008
5L
.201 (5.1mm) .008
US735
.087 (2.2mm) .008
Geometry
Groove Depth:1.378" when

machining diameter is y
Groove Depth:.787" when
Diameter of Workpiece (inch)
.087 (2.2mm) .008

.161 (4.1mm) .008
Left hand insert shown.

Groove Depth:.787" when

Diameter of Workpiece (inch)
GROOVING
Re
Max.Groove Depth (inch)
3N
W3
Max.Groove Depth (inch)
NX55
KGT2N
Dimensions (inch)
NX2525
Order Number
UE6020
Stock
Coated Cermet
(Note) Above insert is not compatible with other manufacturers holders.

Work Material
Mild Steel
Carbon Steel
Alloy Steel
M Stainless Steel
Hardness
Grade
< 180HB
UE6020 NX2525
180 280HB UE6020 NX2525

< 200HB
US735
Cutting Speed
(SFM)
390 (330 460)
Feed (inch/rev)
Groove Width .087" Groove Width .122" Groove Width .161" Groove Width .201"
.004 (.003 .005)
.005 (.004 .006)
.005 (.004 .006)
330 (260 390) .002 (.0015 .0025) .003 (.002 .004)
.003 (.002 .004)
.004 (.003 .005)
.004 (.003 .005)
260 (195 330) .002 (.0015 .0025) .003 (.002 .004)
.004 (.003 .005)
.004 (.003 .005)
(Note) Please set cutting edge height .004 -.008inch higher than center.
SPARE PARTS
M001
TECHNICAL DATA
N001
F159
EXTERNAL GROOVING
MTVO HOLDER
MTVO
a Screw-on type.
a Positive insert products good nish.
a Applicable to narrow grooving and threading.
External grooving, Threading
Max. Groove Depth
Order Number
Insert Number
GROOVING
R L
MTVOR/L-8-3B
10-3B
12-3B
12-4B
16-4D
16-5D
20-4D
H1
a a
32p
a a
a a
a a
TNMC
Max.
Groove
Depth
(inch)
ap
Dimensions (inch)
Stock
L1
L2
F1
Insert Screw Clamp Screw Clamp
.500 4.500 1.000

.625 4.500 1.000
.750 .057 / .156

.875 .057 / .156
GTS1
XNS35
CL6
32p
.500
.625
GTS1
XNS35
CL6
32p
.750
.750 4.500 1.000 1.000 .057 / .156
GTS1
XNS35
CL6
43p
.750
.750 4.500 1.063 1.000 .156 / .234
GTS2
XNS36
CL6
a a
43p
1.000 1.000 6.000 1.063 1.250 .156 / .234
GTS2
XNS36
CL6
a a
54p
43p
1.000 1.000 6.000 1.250 1.250

.297
1.250 1.250 6.000 1.063 1.500 .156 / .234
GTS3
XNS36
CL6
GTS2
XNS36
CL6
a a
Order Number
TNMC32NGR032
32NGL032
32NGR063
32NGL063
43NGR063
43NGL063
43NGR094
43NGL094
43NGR125
43NGL125
43NGR156
43NGL156
54NGR187
54NGL187
Class
INSERTS (GROOVING)
Coated
Stock
Cermet Carbide
Dimensions (inch)
W3
D1
S1
L3
Re
.032
.032
.375
.375
.125
.125
.057
.057
< .003
.063
.375
.125
.156
< .003
.063
.375
.125
.156
< .003
.063
.500
.188
.156
< .003
.063
.500
.188
.156
< .003
.094
.500
.188
.156
< .003
.094
.500
.188
.156
< .003
.125
.500
.188
.234
< .003
.125
.500
.188
.234
< .003
.156
.500
.188
.234
< .003
.156
.500
.188
.234
< .003
E
E
.625
.625
.250
.250
.297
.297
< .003
.187
.187
UP20M
NX55
UTi20T
E
E
Geometry
< .003
< .003
Order Number
TNMC32NV
43NV
54NV
F160
Class
INSERTS (THREADING)
Coated
UP20M
NX55
UTi20T
E
E
E
Stock
Cermet Carbide
Dimensions (inch)
Min.
Pitch
(T.P.I)
D1
S1
Re
8
6
4
.375
.500
.625
.125
.187
.250
.004
.004
.004
Geometry
INTERNAL GROOVING
STHN/O TYPE
S-STHN/O
a Screw-on type.
D4
L1
F1
RR
32p
1.000
10.000
.656
10
1.250
.060 / .156
GTS1
TKY10F
43p
1.250
12.000
.843
10
1.750
.156 / .234
GTS2
TKY20F
43p
1.500
14.000
.968
10
2.250
.156 / .234
GTS2
TKY20F
a a
43p
2.000
14.000
1.218
10
3.000
.156 / .234
GTS2
TKY20F
a a
54p
2.000
14.000
1.250
4.000
.297
GTS3
TKY20F
Insert Number
R L
a a
a a
a a
TNMC
Clamp Screw Wrench
Order Number
TNMC32NGR032
32NGL032
32NGR063
32NGL063
43NGR063
43NGL063
43NGR094
43NGL094
43NGR125
43NGL125
43NGR156
43NGL156
54NGR187
54NGL187
Class
INSERTS (GROOVING)
Coated
Stock
Cermet Carbide
Dimensions (inch)
W3
D1
S1
L3
Re
.032
.032
.375
.375
.125
.125
.057
.057
< .003
.063
.375
.125
.156
< .003
.063
.375
.125
.156
< .003
.063
.500
.188
.156
< .003
.063
.500
.188
.156
< .003
.094
.500
.188
.156
< .003
.094
.500
.188
.156
< .003
.125
.500
.188
.234
< .003
.125
.500
.188
.234
< .003
.156
.500
.188
.234
< .003
.156
.500
.188
.234
< .003
E
E
.625
.625
.250
.250
.297
.297
< .003
.187
.187
UP20M
NX55
UTi20T
E
E
GROOVING
Order Number
S16-STHNR/L-3
S20-STHNR/L-4
S24-STHNR/L-4
S32-STHNR/L-4
S32-STHOR/L-5
Max.
Groove
Depth
(inch)
ap
Min.
Cutting
Diameter
(inch)
D1
Dimensions (inch)
Stock
Geometry
< .003
< .003
Order Number
TNMC32NV
43NV
54NV
Class
INSERTS (THREADING)
E
E
E
Coated
Stock
Cermet Carbide
UP20M
NX55
UTi20T
Dimensions (inch)
Min.
Pitch
(T.P.I)
D1
S1
Re
8
6
4
.375
.500
.625
.125
.187
.250
.004
.004
.004
Geometry
SPARE PARTS
M001
TECHNICAL DATA
N001
F161
INTERNAL GROOVING
GROOVING
SYSTEM
a Min. cutting diameter 10mm.
a Screw-on type.
a Usable for various applications.
a Max. groove depth: 3mm.
F TYPE
FSL51

2 Corner type (FSL5112R,5114R,5116R)
1 Corner type (FSL5108R,5110R)
Metric Standard
Stock
Dimensions (mm)
Insert Number
Order Number
R
s
5110R
5112R
5114R
5116R
GROOVING
FSL5108R
Grooving
MLG
Threading
10ppL
10ppL
14ppL
MLT
1001L
1001L
MLP
D4
H1
L1
L2
F1
W3
1.2
1.5
2.0
1.5
2.0
3.0
2.0
3.0
4.0
1004L
125
30
4.8
1004L
10
150
40
5.8
1404L
12
10.8
180
50
6.8
1404L
14
12.4
180
60
7.8
MLG 20ppL MLT 2001L MLP 2004L
16
14
200
70
9.7
MLG
14ppL
FSL52
MLT
1401L
Boring
1401L
MLP
Min.
Max.
Cutting Groove
Diameter Depth
(mm)
(mm) Clamp
Wrench
Screw
10
1.0 TS25 TKY08F
12
1.0
TS25 TKY08F
14
2.0
TS32 TKY08F
16
2.0
TS32 TKY08F
20
3.0
TS43 TKY15F
Carbide shank
Metric Standard
Stock
Dimensions (mm)
Insert Number
Order Number
R
FSL5208R
5210R
5212R
5214R
5216R
Grooving
MLG
Threading
10ppL
10ppL
1001L
1001L
H1
L1
L2
F1
W3
1.2
1.5
2.0
1.5
2.0
3.0
2.0
3.0
4.0
1004L
125
60
4.8
1004L
10
150
70
5.8
1404L
12
10.8
180
80
6.8
14
12.4
180
85
7.8
16
14
200
115
9.7
14ppL
MLT
1401L
MLP
D4
1404L
MLG
14ppL
MLT
Boring
1401L
MLP
Min.
Max.
Cutting Groove
Diameter Depth
(mm)
(mm) Clamp
Wrench
Screw
10
1.0 TS25 TKY08F
12
1.0
TS25 TKY08F
14
2.0
TS32 TKY08F
16
2.0
TS32 TKY08F
20
3.0
TS43 TKY15F

Work Material
Hardness
Grade
Cutting Speed
(SFM)
Feed
(inch/rev)
P Carbon Steel
180 280HB
UP20M UTi20T
295 (195 390)
.002 (.0008 .003)
UP20M UTi20T
260 (165 330)
.001 (.0008 .0015)
Alloy Steel
F162
280 350HB
INSERTS
F164
F TYPE
a Min. cutting diameter .390inch.

a Screw-on type.
a Max. groove depth: .118inch.
S-SL5N

2 Corner type (S-SL5NR08 / 10 / 12)
1 Corner type (S-SL5NR05 / 06)
(Min.Bore)
(Min.Bore)
Dimensions (inch)
Insert Number
Grooving
Threading
D4
L1
L2
F1
W3
.062
.094
S-SL5NR05
MLG10WpppL
MLT1001L
.313
5.000
1.250
.188
06
MLG10WpppL
MLT1001L
.375
6.000
1.500
.219
08
MLG14WpppL
MLT1401L
.500
10
MLG20WpppL
MLT2001L
.625
8.000
3.000
.375
12
MLG20WpppL
MLT2001L
.750
10.000
4.000
.438
7.000
2.000
.281
.062
.094
.125
.094
.125
.156
Max.
Min.
Cutting Groove
Diameter Depth
(inch)
(inch)
ap
Clamp Screw Wrench
D1
.390
.039
TS25
TKY08F
.449
.039
TS25
TKY08F
.579
.079
TS32
TKY08F
.791
.118
TS43
TKY15F
.902
.118
TS43
TKY15F
GROOVING
Order Number
Stock

Work Material
Hardness
Grade
Cutting Speed
(SFM)
Feed
(inch/rev)
P Carbon Steel
180 280HB
UP20M UTi20T
295 (195 390)
.002 (.0008 .003)
280 350HB
UP20M UTi20T
260 (165 330)
.001 (.0008 .0015)
Alloy Steel
SPARE PARTS
M001
TECHNICAL DATA
N001
F163
INTERNAL GROOVING
GROOVING
SYSTEM
F TYPE

a Screw-on type.
INSERTS
UP20M
UTi20T
HTi10
Application
.062
MLG10W062L
.276 .197 .039 .094
.004
.094
10W094L
.276 .197 .039 .094
.004
Inch
Metric
Grooving
Inch
L1
F164
a
r
L2
L3
S1
Re
MLG1012L
.276 .197 .039 .094
.004
.059 (1.5mm)
1015L
.276 .197 .039 .094
.004
.079 (2.0mm)
1020L
.276 .197 .039 .094
.004
.062
MLG14W062L
.465 .256 .079 .187
.004
.094
14W094L
.465 .256 .079 .187
.004
.125
14W125L
.465 .256 .079 .187
.004
.094
20W094L
.661 .356 .118 .250
.004
.125
20W125L
.661 .356 .118 .250
.004
20W156L
.661 .356 .118 .250
.004
.059 (1.5mm)
MLG1415L
.465 .256 .079 .187
.004
.079 (2.0mm)
1420L
.465 .256 .079 .187
.004
.118 (3.0mm)
1430L
.465 .256 .079 .187
.004
.079 (2.0mm)
2020L
.661 .356 .118 .250
.004
.661 .356 .118 .250
.004
.661 .356 .118 .250
.004
.118 (3.0mm)
2030L
.157 (4.0mm)
2040L
Min.Pitch 13T.P.I
MLT1001L
.276 .197
.094 .004
Min.Pitch 11T.P.I
1401L
.465 .256
.187 .004
Min.Pitch 8T.P.I
2001L
.661 .356
.250 .004
MLP1004L
.276 .197 .039 .094 .016
1404L
.465 .248 .079 .187 .016
2004L
.661 .356 .118 .250 .016
Boring
Threading
Order Number
.047 (1.2mm)
.156
Metric
GROOVING
Dimensions (inch)
Coated Carbide
Groove Width
(inch)
W3

Geometry
MLG...L (1 Corner type)
MLT1001L, MLP1004L
(1 Corner type)
MLT1401L /2001L
MLP1404L /2004L
(2 Corner type)
MICRO-MINI TWIN
CG
Internal grooving
D1
W30.03
Re
F2
F1
Re
D4
H1
L1
L10
L2
CG0305RS-10
0305RS-10B
0306RS-20
0306RS-20B
03RS-10
03RS-10B
03RS-20
03RS-20B
0407RS-10
0407RS-10B
0408RS-20
0408RS-20B
04RS-10
04RS-10B
04RS-20
04RS-20B
0510RS-10
0510RS-10B
0511RS-20
0511RS-20B
05RS-10
05RS-10B
05RS-20
05RS-20B
0610RS-10
0610RS-10B
0611RS-20
0611RS-20B
06RS-10
06RS-10B
06RS-20
06RS-20B
0712RS-10
0712RS-10B
0713RS-20
0713RS-20B
07RS-10
07RS-10B
07RS-20
07RS-20B
3
3
1
1
Dimensions (mm)
Re
D4
L1
L10
L2
F1
H1
0.05
0.05
3
3
50
50
5
5
6
6
1.3
1.3
2.7
2.7
1.2
1.2
Without
With
Without
0.1
50
1.3
2.7
1.2
With
0.1
50
1.3
2.7
1.2
Without
0.05
50
10
1.3
2.7
1.2
With
0.05
50
10
1.3
2.7
1.2
Without
0.1
50
11
1.3
2.7
1.2
With
0.1
50
11
1.3
2.7
1.2
Without
1.5
0.05
60
1.8
3.6
2.0
With
1.5
0.05
60
1.8
3.6
2.0
Without
1.5
0.1
60
1.8
3.6
2.0
With
1.5
0.1
60
1.8
3.6
2.0
Without
1.5
0.05
60
15
1.8
3.6
2.0
With
1.5
0.05
60
15
1.8
3.6
2.0
Without
1.5
0.1
60
16
1.8
3.6
2.0
With
1.5
0.1
60
16
1.8
3.6
2.0
Without
0.05
70
10
2.3
4.5
2.8
With
0.05
70
10
2.3
4.5
2.8
Without
0.1
70
11
2.3
4.5
2.8
With
0.1
70
11
2.3
4.5
2.8
Without
0.05
70
20
2.3
4.5
2.8
With
0.05
70
20
2.3
4.5
2.8
Without
0.1
70
21
2.3
4.5
2.8
With
0.1
70
21
2.3
4.5
2.8
Without
0.05
75
10
2.8
5.4
2.8
With
0.05
75
10
2.8
5.4
2.8
Without
0.1
75
11
2.8
5.4
2.8
With
0.1
75
11
2.8
5.4
2.8
Without
0.05
75
20
2.8
5.4
2.8
With
0.05
75
20
2.8
5.4
2.8
Without
0.1
75
21
2.8
5.4
2.8
With
0.1
75
21
2.8
5.4
2.8
Without
0.05
85
12
3.3
6.4
2.8
With
0.05
85
12
3.3
6.4
2.8
Without
0.1
85
13
3.3
6.4
2.8
With
0.1
85
13
3.3
6.4
2.8
Without
0.05
85
25
3.3
6.4
2.8
With
0.05
85
25
3.3
6.4
2.8
Without
With
7
7
2
2
2
2
0.1
0.1
7
7
85
85
26
26
8
8
3.3
3.3
6.4
6.4
2.8
2.8
: Inventory maintained. (1 MICRO-MINI TWIN in one case)
1
1
* Only for CG03ppRS-ppB
CUTTING CONDITIONS
F166
SPARE PARTS
M001
TECHNICAL DATA
N001
GROOVING
Order Number
Min.
Stock
Groove Max.
Cutting
Groove
Micro Grain Coated
Diameter Width Depth
Breaker
Carbide
(mm) (mm)
(mm)
D1
F2
TF15 VP15TF
W3
F165
GROOVINGGROOVING
SYSTEM
INTERNAL
HOLDER
Holder
MICRO-MINI TWIN
Machine Makers
Order Number
ID : Metric Type
Type
ID : Metric Type
Round Type Holder

& .625inch
ID : Metric Type
GROOVING
Round Type Holder

& .750inch
Round Type Holder

& 1.000inch
CG
RBH10189A
030pRS-pp(B), 03RS-pp(B)
10252A
10315A
10378A
10441A
RBH19030N
19040N
19050N
19060N
19070N
RBH16189A
16252A
16315A
16378A
16441A
Citizen Precision Machinery Co., Ltd.

NC lathes

NC lathes
MICRO-MINI TWIN
CG type
Holder
(Note) For L10, refer to page F165.

Work Material
03RS/04RS
05RS/06RS/07RS
General Steel
130 395
.0004 .001
.0004 .002
Stainless Steel
130 395
.0004 .001
.0004 .002
Cast Iron
130 395
.0004 .002
.0004 .002
260 525
.0004 .002
.0004 .003
(Note) Recommend wet machining.
F166
Feed (IPR)
Cutting Speed
(SFM)

Holder
MICRO-MINI TWIN
Machine Makers
Round Type Holder

& 16mm
Round Type Holder

& 20mm
Round Type Holder

& 22mm
Round Type Holder

& 25mm
Square Type Holder

r10mm
Order Number
CG
RBH1630N
1640N
1650N
1660N
1670N
RBH2030N
2040N
2050N
2060N
2070N
RBH2230N
2240N
2250N
2260N
2270N
RBH2530N
2540N
Tsugami Corporation
2550N
MIYANO MACHINERY JAPAN INC.
2560N
NC lathes
2570N
SBH1030R
1040R
1050R
1060R
1070R

NC lathes

Tsugami Corporation
NC lathes
GROOVING
Type
STAR MICRONICS CO., LTD.
NC lathes
HOLDER
E034, E036, E037
SPARE PARTS
M001
TECHNICAL DATA
N001
F167
GUIDE TO
THREADING TOOLS
a Section
organization
z Classied according to external or internal applications.

x Sub-classied according to product series.
FIGURE SHOWING THE TOOLING APPLICATION

uses illustrations and arrows to depict the available machining
applications, such as external and internal threading.
TYPE OF TOOL HOLDER

indicates the initial letters for the order number
and cutting applications.
TITLE OF
PRODUCT
INDICATION OF EXTERNAL
/INTERNAL APPLICATION
STANDARDS FOR APPLICABLE INSERTS
PRODUCT
SECTION
indicates stock status, dimensions, etc.

for applicable inserts.
PRODUCT FEATURES
THREADING
THREADING
MMTE

a Available with a wiper cutting edge to provide a precise thread geometry.
a Able to change lead angle by replacing the shim.
HOLDER
MMTE
MMT M-CLASS INSERTS WITH 3-D CHIP BREAKERS

EXTERNAL THREADING INSERTS
(External threading)
Partial Prole 55 Partial Prole 60
L1
Details of position A
(Refer to pages G014-G020 for size Z1, Z2)
H1
H2
MMTER-083
-103
MMT16ER
-123
ooooo
-163
MMTER-124
-164
-204
MMT22ER
ooooo
L1
L2
H2
F1
*2
z
x
Clamp Bridge Clamp Screw Stop Ring Shim Screw
.500 .500 4.000 1.000 .500 .625 SETK51 SETS51
CR4
.625 .625 4.000 1.000 .625 .750 SETK51 SETS51
*1
Shim
HFC03008 CTE32TP15
CR4
HFC03008 CTE32TP15
.750 .750 5.000 1.000 .750 1.000 SETK51 SETS51
CR4
HFC03008 CTE32TP15
1.000 1.000 6.000 1.000 1.000 1.250 SETK51 SETS51
CR4
HFC03008 CTE32TP15
.750 .750 5.000 1.250 .750 1.000 SETK61 SETS61
CR5
HFC04010 CTE43TP15
1.000 1.000 6.000 1.250 1.000 1.250 SETK61 SETS61
CR5
HFC04010 CTE43TP15
1.250 1.250 6.000 1.250 1.250 1.500 SETK61 SETS61
CR5
HFC04010 CTE43TP15
Wrench
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY20F
xHKY25R
zTKY20F
xHKY25R
zTKY20F
xHKY25R
THREADING
Select and use an alternate shim from list below (sold separately), dependant on the lead angle.
*21 Clamp
Torgue (lbf-in) : SETS51=31, SETS61=44, HFC03008=13, HCF04010=19
*
SHIM
Lead Angle
(%)
Order Number
1.5 CTE32TN15
0.5
N05
0.5
P05
1.5
P15
2.5
P25
3.5
P35
4.5
P45
Stock Inclination
Angle
R
(')
a
a
a
a
a
a
a
3
2
1
0
1
2
3
Applicable
Holder
Lead Angle
(%)
Order Number
Stock Inclination
Angle
R
(')
1.5 CTE43TN15
0.5
N05
0.5
P05
1.5
P15
2.5
P25
3.5
P35
4.5
P45
MMTER
-oo3
Applicable
Holder
3
2
1
0
1
2
3
a
a
a
a
a
a
a
Shim
Standard shim delivered with the holder.
* See page G025 for shim selection guide lines.
Designation
Application
External
E
08
Hand of Tool
Right
R
BSPT
IDENTIFICATION
MMT
3
Insert Size
MMT16
3
MMT22
4
Tool Size (inch)

(Height and Width)
.500
08
.625
10
.750
12
1.000
16
1.250
20
Work Material
G012
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180 280HB
Stainless Steel
< 200HB
Grade
Cutting Speed (SFM)
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF
VP20RT
490 (230 755)

330 (195 460)
260 (195 330)
460 (260 655)
330 (195 460)
260 (195 330)
425 (260 590)
260 (130 395)
195 (130 260)
VP15TF
a
MMT16ERA55-S
16ERG55-S
MMT16ER100ISO-S
16ER125ISO-S
16ER150ISO-S
16ER175ISO-S
16ER200ISO-S
16ER250ISO-S
16ER300ISO-S
MMT16ER160UN-S
16ER140UN-S
16ER120UN-S
MMT16ER190W-S
16ER140W-S
16ER110W-S
MMT16ER190BSPT-S
16ER140BSPT-S
16ER110BSPT-S
Work Material
Cast Iron
S Heat-Resistant Alloy
H
Z1
Z2
Re
48 16
14 8
9.525
9.525
3.44
3.44
0.8
1.2
0.9
1.7
0.06
0.23

Partial form
48 16
14 8
9.525
9.525
3.44
3.44
0.8
1.2
0.9
1.7
0.07
0.23

Partial form
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
0.7
0.8
0.8
0.9
1.0
1.1
1.2
0.9
1.0
1.1
0.7
0.9
1.0
1.2
1.3
1.5
1.6
1.1
1.2
1.4
0.13
0.16
0.20
0.22
0.26
0.33
0.40
0.23
0.26
0.30
0.61
0.77
0.92
1.07
1.23
1.53
1.84
0.97
1.11
1.30
Full form
16
14
12
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
19
14
11
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
1.0
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
Full form
19
14
11
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
0.9
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
Full form
1.0
1.25
1.5
1.75
2.0
2.5
3.0
a
a
a
s
s
s
s
Full form
S M-class inserts with 3-D chip breakers

Designation
Geometry
S1
0.5 1.5
1.75 3.0
Total
depth
of cut
(mm)
D1
thread/inch
IDENTIFICATION

P
MMT16ERA60-S
16ERG60-S
Pitch
mm
Insert
Inclination
Angle
(')
MMTER
-oo4
Whitworth for BSW, BSP
THREADING
H1
*2
ISO Metric
Stock

Dimensions (inch)
Insert Number
American UN
L1
10
VP20RT
Type
Z2
F1
F1
A
Order Number
Z1
L2
Order Number
Dimensions (mm)
Coated
1.5
Hardness
Grade
Cutting Speed (SFM)
Tensile Strength
VP10MF
VP15TF
VP10MF
VP15TF
VP10MF
VP15TF
VP10MF
VP15TF
460 (260 655)

295 (195 395)
150 ( 50 230)
100 ( 65 130)
195 (130 260)
150 ( 80 210)
165 (100 230)
130 ( 65 195)
< 350MPa
Titanium Alloy
Hardened Steel
45 55HRC
How to select a shim
LEGEND FOR
STOCK STATUS MARK
G025
Diameter of Inscribed
Circle (mm)
6.35
11
9.525
16
G014
Hand of Tool
Right
R
Application
E External
Internal
I
Pitch
100
1.0mm
125
1.25mm
150
1.5mm
175
1.75mm
200
2.0mm
250
2.5mm
300
3.0mm
0.5 1.5mm
or
48 16 thread/inch
1.75 3.0mm
or
14 8 thread/inch
Threading Type
60 Partial Prole 60
55 Partial Prole 55
ISO ISO Metric
W Whitworth for BSW, BSP
BSPT BSPT
UN American UN

a
PAGE REFERENCE
SPARE PARTS
STANDARD OF DEPTH OF CUT
indicates reference pages, including the above,
on the right hand page of each double-page spread.
PRODUCT STANDARDS
indicates order numbers, stock status
(per right/left hand), applicable inserts,
holder dimensions, and spare parts.
IDENTIFICATION FOR INSERTS

for each work material classication, indicates
recommended cutting conditions according to the ISO
categories for cutting grades, P, M, K, N, S and H.
aTo
G000
Order :
For holder, please specify order number and hand of tool (right/left).
For insert, please specify insert number and grade.
TURNING TOOLS
THREADING
CLASSIFICATION (EXTERNAL) ...................................................................... G002
CLASSIFICATION (INTERNAL) ....................................................................... G003
CROSS REFERENCE THREAD PITCH
EXTERNAL ........................................................................................ G004
INTERNAL ......................................................................................... G006
STANDARD THREAD AND CORRESPONDING INSERTHOLDER .............. G008
PIPE THREADS AND TOOL SELECTION ....................................................... G009
FEATURES OF MMT SERIES .......................................................................... G010
STANDARD OF THREADING TOOLS
EXTERNAL THREADING
MMTE HOLDER ..................................................................................... G012
MTVO HOLDER ..................................................................................... G034
INTERNAL THREADING
MMTI TYPE BORING BARS ........................................................................ G013
STHN/O TYPE BORING BARS ................................................................... G035
FSL5 TYPE BORING BARS ........................................................................ G036
SL5N TYPE BORING HEAD ........................................................................ G037
MICRO-MINI TWIN(CT) BORING BARS .................................................. G039
THREADING METHOD..................................................................................... G022
STANDARD OF DEPTH OF CUT ..................................................................... G026
TROUBLE SHOOTING ..................................................................................... G032

*G039
CT
G036
G036
G038
G038
G038
G014
G012
G013
G034
G037
G035
G034
FSL51
FSL52
MLG (INSERTS)
MLP (INSERTS)
MLT (INSERTS)
MMT (INSERTS)
MMTE
MMTI
MTVO
S-SL5N
S-STHN/O
TNMC (INSERTS)
G001
THREADING
CLASSIFICATION
EXTERNAL CUTTING
Name of Tool Holder
Insert Shape
Features

a Available with a wiper cutting
MMTE Holder
edge to provide a precise thread

geometry.
^ G012
a Clamp-on type.
a Positive insert produces
MTVO Holder
THREADING
^ G034
G002
a good nished surface.
INTERNAL CUTTING
Name of Tool Holder
Insert Shape
Features
a Minimum cutting diameter .500 inch.

a Available with a wiper cutting edge to
MMTI
provide a precise thread

geometry.
a Able to change lead angle by replacing shim.
^ G013
a Screw-on type.
a Holder is capable of performing both grooving
STHN/0
and threading.
a Screw-on type.
a Holder is capable of performing both
a Maximum groove depth .118inch.
FSL5
S-SL5
grooving and threading.
^ G036
^ G037
a Solid carbide type.
a Economical due to
MICRO-MINI TWIN
Boring Bars
THREADING
^ G035
single holder with two cutting edges.
^ G039
a Solid carbide
a Insert can be
MICRO-MINI
Boring Bars
type.
ground to suit the application.
^ E031
G003
THREADING
THREAD PITCH CROSS REFERENCE

Pipe ttings and couplings
for gas and water
General machining
Type
ISO Metric
Pitch
Holder
60
60
THREADING
Partial
form
^ G034
G004
R=0.137329P
30
UNC
UNF
G
W
NPT
mm
(thread/inch)
thread/inch
mm
thread/inch
thread/inch
thread/inch
0.5
0.75
1.0
1.25
1.5
1.75
2.0
2.5
3.0
3.5
4.0
4.5
5.0
32
28
24
20
18
16
14
13
12
11
10
9
8
7
6
5
^ G014, G016
^ G014, G018
4816
14 8
48 8
7 5
0.5 1.5
1.753.0
0.5 3.0
3.5 5.0
4816
14 8
48 8
7 5
^ G014, G016
^ G016
^ G016
0.53.0
0.54.5
0.56.0
488
486
484
^ G034
^ G034
^ G014, G016
MTVO
Holder
0.25P
30
0.5 1.5(4816)
1.753.0(14 8)
Partial 0.5 3.0(48 8)
form 3.5 5.0(07 5)
^ G012
55
M
UNC
UNF
MMT Holder
Full
form
American
NPT
R=0.137329P
55
0.25P
Symbol
Parallel Pipe
Thread
Whitworth
for BSW, BSP
0.125P
0.125P
60
American
UN
147'
Partial Prole Partial Prole

60
55
90
Application
0.53.0
0.54.5
0.56.0
^ G034
28
26
20
19
18
16
14
12
11
10
9
8
7
6
5
27
18
14
11.5
8
^ G014, G018
^ G020
Round
DIN 405
27.5 27.5
30
147'
30
90
R=0.137278P
30
147'
American
ACME
R=0.221047P
R=0.255967P
R=0.137278P
90
ISO Trapezoidal
30
Oil and gas
UNJ
API Buttress API Round

Casing
Casing & Tubing
0.125P
29
30
10
0.366P
R=0.238507P
30 30
60
R=0.18042P
90
147'
American
NPTF
Aircraft and
aerospace
90
Taper Pipe
Thread
BSPT
Motion transmissions
147'
Pipe couplings
for food and re
ghting industries
Steam, gas and

water pipes
NPTF
Rd
Tr
ACME
UNJ
BCSG
CSG
LCSG
thread/inch
thread/inch
thread/inch
mm
thread/inch
thread/inch
thread/inch
thread/inch
28
19
14
11
27
18
14
11.5
8
10
8
6
4
1.5
2.0
3.0
4.0
5.0
12
10
8
6
5
10
8
^ G014, G018
^ G020
^ G018
^ G020
^ G020
^ G020
^ G020
^ G020
32
28
24
20
18
16
14
12
10
8
THREADING
BSPT
R
Rc
Rp
G005
THREADING
THREAD PITCH CROSS REFERENCE

Pipe ttings and couplings
for gas and water
General machining
Type
ISO Metric
Pitch
Holder
60
60
THREADING
Partial
form
^ G035
FSL5
SL5N
Boring Bars
Partial
form
^ G036
^ G037
MICRO-MINI TWIN
^ G039
G006
R=0.137329P
30
UNC
UNF
G
W
NPT
mm
(thread/inch)
thread/inch
mm
thread/inch
thread/inch
thread/inch
0.5
0.75
1.0
1.25
1.5
1.75
2.0
2.5
3.0
3.5
4.0
4.5
5.0
32
28
24
20
18
16
14
13
12
11
10
9
8
7
6
5
^ G015, G017
^ G015, G019
4816
14 8
48 8
7 5
0.5 1.5
1.753.0
0.5 3.0
3.5 5.0
4816
14 8
48 8
7 5
^ G015, G017
^ G017
^ G017
0.53.0
0.54.5
0.56.0
488
486
484
^ G035
^ G035
^ G035
1.5 2.0
1.5 2.5
1.5 3.5
1.52.0
1.52.5
1.53.5
4813
4811
48 8
^ G038
^ G038
0.5 -1.0
0.75-1.25
0.75-1.5
0.75-1.75
3624
2820
2418
2416
^ G039
^ G039
^ G015, G017
STHN/O
Boring Bars
0.25P
30
0.5 1.5(4816)
1.753.0(14 8)
Partial 0.5 3.0(48 8)
form 3.5 5.0(07 5)
^ G013
55
M
UNC
UNF
MMT
Boring Bars
Full
form
American
NPT
R=0.137329P
55
0.25P
Symbol
Parallel Pipe
Thread
Whitworth
for BSW, BSP
0.125P
0.125P
60
American
UN
147'
Partial Prole Partial Prole

60
55
90
Application
0.5 3.0
0.5 4.5
0.5 6.0
^ G038
0.5 1.0 (3624)

0.751.25(2820)
Partial 0.751.5 (2418)
form 0.751.75(2416)
^ G039
28
26
20
19
18
16
14
12
11
10
9
8
7
6
5
27
18
14
11.5
8
^ G015, G019
^ G021
Round
DIN 405
27.5 27.5
30
147'
30
90
R=0.137278P
147'
30
UNJ
API Buttress API Round

Casing
Casing & Tubing
American
ACME
R=0.221047P
R=0.255967P
R=0.137278P
90
ISO Trapezoidal
30
Oil and gas
0.125P
29
30
10
0.366P
R=0.238507P
30 30
60
R=0.18042P
90
147'
American
NPTF
Aircraft and
aerospace
90
Taper Pipe
Thread
BSPT
Motion transmissions
147'
Pipe couplings
for food and re
ghting industries
Steam, gas and

water pipes
NPTF
Rd
Tr
ACME
UNJ
BCSG
CSG
LCSG
thread/inch
thread/inch
thread/inch
mm
thread/inch
thread/inch
thread/inch
thread/inch
19
14
11
14
11.5
8
10
8
6
4
1.5
2.0
3.0
4.0
5.0
12
10
8
6
5
10
8
THREADING
BSPT
R
Rc
Rp
^ G015, G019
^ G021
^ G019
^ G021
^ G021
^ G021
^ G021
machining an internal UNJ thread, cut an internal hole with the appropriate diameter. Then machine with 60 American UN.
* When
In this case, a full form type insert cannot be used.
G007
THREADING
STANDARD THREAD AND CORRESPONDING INSERT

0.541266P 0.108253P
Female
Thread
30
M
UNC
UNF
30
BSPT
R
Rc
Rp
BSPT
Female
Thread
60
Male Thread
P
Axis
Rd
0.0328P
0.8P
0.866025P
0.038P
30 30
60
0.933P
0.5P
NPT
90
Female
Thread
0.25P 0.25P
0.038P
1.8660P
Axis
147'
0.038P
0.366P
Tr
15
15
30
0.933P
0.038P
ISO Trapezoidal 30
Female Thread
0.0328P
0.0328P
0.0328P
0.5P
0.05P
Male
Thread
Female
Thread
0.05P
0.2
38
50
7P
0.25P
0.5P
Round DIN 405
Male Thread
7P
04
21
0.2
W
G
30
7P
596
0.25
Female
Thread
THREADING
Symbol
0.125P
0.216506P
0.866025P
0.433013P 0.433013P
Standard Thread Type
7P
850
0.23
American NPT
Symbol Thread
Name
Standard Thread Type
Parallel Pipe Thread

ISO Metric / American UN
Thread
Name
Male Thread
0.366P
Male Thread
taper shown
exaggerated
API Buttress Casing
Sc1
0.5P
0.25P 0.25P
CSG
LCSG
1430' 1430'
1.9334P
Pitch line
American ACME
30
60
Frs
Fcn
Fcs
Frn
90
P
taper = 3/4 in. per it. (62.5mm per m) on daimeter
B(NR)
G008
h1
H
hs
p/2
30
Female
Thread
29
Sn
Scs
Srs
API Round Casing & Tubring
B(ER)
BCSG
147'
10
parallel to taper
Male
Thread
ACME
PIPE THREADS AND TOOL SELECTION

Parallel Pipe Threads
Thread Type
Number of threads
G1/16
28
G1/8
G1/4
19
G3/8
G1/2
Standard internal diameter

.258"
.337"
.451"
.589"
.734"
G5/8
14
G3/4
.811"
.949"
G7/8
1.098"
G1
1.193"
G11/8
11
G11/4
1.376"
1.534"
Taper Pipe Threads

Thread Type
R1/16
R1/8
R1/4
R3/8
R1/2
R, Rc
Number of threads
28
19
14
Standard internal diameter
THREADING
Note) Same as PF.
.258"
.337"
.451"
.589"
.734"
R3/4
14
.949"
R1
11
1.193"
R11/4
11
1.534"
Note) Same as Rc and PT.

The pitch is pre-determined for each nominal diameter. Note the
minimum machining diameter especially when internal threading.
G009
THREADING
FEATURES OF MMT SERIES

y A WIDE VARIETY OF CHOICES
Mitsubishi Miracle Threading (MMT) series contains 297 inserts and 21 holders.
M-CLASS INSERTS WITH 3-D CHIP BREAKERS
G-CLASS GROUND INSERTS
UNC
Rp
Rc
UNC
UNF
Rp
Rc
UNF
F
NPT
T
NP
W
Rd
E
ACM
LCS
G
BCS
THREADING
Tr
CSG
y IDEAL CHIP CONTROL EVEN IN THE LATTER HALF OF PASSES WHEN CONTINUOUS CHIPS
ARE USUALLY PRODUCED. (M-CLASS INSERTS WITH 3-D CHIP BREAKERS)

ISO metric external thread pitch 1.5mm Final pass (6th pass)
MMT
Competitor
Workpiece : AISI 4140
Insert : MMT16ER150ISO-S
Grade : VP15TF
Cutting method : Radial Infeed
Depth of cut : Fixed cut area
Pass : 6 times
Coolant : Wet
y A HIGHER LEVEL OF PRECISION THAN
CONVENTIONAL INSERTS (G-CLASS GROUND INSERTS)

Theoretical
thread prole
MMT series
Conventional insert
High precision threading can be achieved by using MMT

inserts that feature a ground rake face and peripheral cutting
edge.
G010
Thread Type
Threading Tolerance
ISO Metric
6g / 6H
American UN
2A / 2B
Medium Class A
BSPT
Standard BSPT
Round DIN 405
7h / 7H
ISO Trapezoidal 30
7e / 7H
American ACME
3G
UNJ
3A
API Buttress Casing
Standard API
API Rounded Casing & Tubing
Standard API RD
American NPT
Standard NPT
American NPTF
Class2
y HOLDER (Use of special surface treatment)

External
Clamp-on type allows
easy indexing.
Internal
Coolant ows directly to
the cutting edge through
a coolant nozzle in the
center of the shank.
Reduced neck MMT holders

prevents chips from jamming.
By changing the shim, MMT holders

can be used for cutting threads with
various lead angles.
Lead Angle ( %)
Lead Angle (%)
Inclination Angle (')
1.5
3
0.5
2
0.5
1
1.5
2.5
3.5
4.5
Insert
Inclination
Angle
( ')
Shim
By changing only the shim, MMT holders can be used for turning of threads
with various lead angles as well as the turning of left hand threads.
(Please refer to page G022 and page G025)
y
Delivered with the holder.
THREADING
y SUITABLE FOR THREADING WITH A LARGE LEAD ANGLE
VP10MF (G-class ground inserts only)
a Superior wear and plastic deformation resistance

a Suitable for continuous high precision machining with extensive tool life.
High wear and plastic deformation resistance for threading when maintaining the thread form is important.
Effective in combination with G-class inserts for high precision threading.
VP15TF (G-class ground inserts, M-class inserts with 3-D chip breakers)
a Wide versatility
a Able to withstand harsh conditions for long periods where conventional inserts would be liable to breakage.
High fracture resistance during low rigidity applications such as bar feed machining.
Effective combination of high cost performance M-class inserts with 3-D chip breakers.
VP20RT (G-class ground inserts, M-class inserts with 3-D chip breakers)
a Excellent fracture resistance
Suitable for stainless steel boring and unstable machining where inserts are vulnerable to fracturing.
Effective combination of high cost performance M-class inserts with 3-D chip breakers.
y CHOOSING M-CLASS INSERTS WITH 3-D CHIP BREAKERS OR G-CLASS INSERTS

Insert
M-class inserts with 3-D
chip breakers
Chip control Precision of thread
Insert
G-class inserts
Chip control Precision of thread
e : 1st recommendation
u : 2nd recommendation
For ideal chip control and a high

cost performance ratio, M-class
inserts with 3-D chip breakers are
recommended.
G-class inserts are recommended
where higher precision is
required.
G011
THREADING
MMTE
HOLDER
MMTE

a Available with a wiper cutting edge to provide a precise thread geometry.
F1
Z2
F1
(External threading)
1.5
Z1
L2
A
L1
L1
(Refer to pages G014-G020 for size Z1, Z2)
H1
H2
10
Stock
THREADING
Order Number
Insert Number
L2
H2
F1
z
x
H1
MMTER-083
.500 .500 4.000 1.000 .500 .625 SETK51 SETS51
CR4
HFC03008 CTE32TP15
-103
.625 .625 4.000 1.000 .625 .750 SETK51 SETS51
CR4
HFC03008 CTE32TP15
-123
.750 .750 5.000 1.000 .750 1.000 SETK51 SETS51
CR4
HFC03008 CTE32TP15
-163
1.000 1.000 6.000 1.000 1.000 1.250 SETK51 SETS51
CR4
HFC03008 CTE32TP15
MMTER-124
HFC04010 CTE43TP15
CR5
HFC04010 CTE43TP15
-204
.750 .750 5.000 1.250 .750 1.000 SETK61 SETS61

MMT22ER
1.000 1.000 6.000 1.250 1.000 1.250 SETK61 SETS61
ooooo
1.250 1.250 6.000 1.250 1.250 1.500 SETK61 SETS61
CR5
-164
CR5
HFC04010 CTE43TP15
MMT16ER
ooooo
L1
*2
Dimensions (inch)
Clamp Bridge Clamp Screw Stop Ring Shim Screw
Shim
Wrench
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY20F
xHKY25R
zTKY20F
xHKY25R
zTKY20F
xHKY25R
1 Select and use an alternate shim from list below (sold separately), dependant on the lead angle.
2 Clamp Torgue (lbf-in) : SETS51=31, SETS61=44, HFC03008=13, HCF04010=19
*
*
SHIM
Lead Angle
(%)
Order Number
1.5 CTE32TN15
0.5
N05
0.5
P05
1.5
P15
2.5
P25
3.5
P35
4.5
P45
Stock Inclination
Angle
R
(')
a
a
a
a
a
a
a
3
2
1
0
1
2
3
Applicable
Holder
Lead Angle
(%)
Order Number
1.5 CTE43TN15
0.5
N05
0.5
P05
1.5
P15
2.5
P25
3.5
P35
4.5
P45
MMTER
-oo3
Stock Inclination
Angle
R
(')
a
a
a
a
a
a
a
Applicable
Holder
3
2
1
0
1
2
3
Insert
Inclination
Angle
(')
MMTER
-oo4
Shim

See page G025 for shim selection guide lines.
IDENTIFICATION
MMT
Designation
Application
External
E
Hand of Tool
Right
R
08
3
Insert Size
MMT16
3
MMT22
4
Tool Size (inch)

(Height and Width)
.500
08
.625
10
.750
12
1.000
16
1.250
20

Work Material
G012
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180 280HB
Stainless Steel
Hardness
< 200HB
Grade
Cutting Speed (SFM)
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF
VP20RT
490 (230 755)

330 (195 460)
260 (195 330)
460 (260 655)
330 (195 460)
260 (195 330)
425 (260 590)
260 (130 395)
195 (130 260)
Work Material
Cast Iron
H
Hardness
Grade
Cutting Speed (SFM)
Tensile Strength
VP10MF
VP15TF
VP10MF
VP15TF
VP10MF
VP15TF
VP10MF
VP15TF
460 (260 655)

295 (195 395)
150 ( 50 230)
100 ( 65 130)
195 (130 260)
150 ( 80 210)
165 (100 230)
130 ( 65 195)
< 350MPa
Titanium Alloy
Hardened Steel
45 55HRC
How to select a shim
G025
MMTI
a Minimum cutting diameter .500".

a Available with a wiper cutting
TYPE
BORING BARS
MMTI
edge to provide a precise thread

geometry.
a Able to change lead angle by
replacing shim.
(Internal threading)
Fig.1 (Screw-on type)
Fig.2 (Screw-on type)

F1
F1
15
Fig.3 (Clamp-on type)

F1
L3
Lead Angle
Stock
Order Number
Insert
Number
L3
L1
D1
D4
L1
L3
F1
H1
(Refer to pages G015
-G021 for size Z1, Z2)
Z2
L2
L1
Min.
Cutting
Diameter
(inch)
Dimensions (inch)
L1
F1
Z1
Fig.4 (Clamp-on type)
F1
15
L3
H1
D4
L1
*2
z
x Fig.
D1 Clamp Bridge Clamp Screw Stop Ring Shim Screw Shim 1 Wrench
TS25
zTKY08F
a MMT11IR
TS25
zTKY08F
a ooooo
TS25
zTKY08F
a
TS25
zTKY08F
a
CS350860T
zTKY15F
a
CS350860T
zTKY15F
MMT16IR
a
SETK51 SETS51
CR4 HFC03006 CTI32TP15 zTKY15F
xHKY20R
ooooo
a
SETK51 SETS51
xHKY20R
a
SETK51 SETS51
xHKY20R
a
TS43
zTKY15F
a
TS43
zTKY15F
MMT22IR
a
SETK61 SETS61
xHKY25R
ooooo
a
SETK61 SETS61
xHKY25R
a
SETK61 SETS61
xHKY25R
1 Select and use an alternate shim from list below (sold separately), dependant on the lead angle.
2 Clamp Torgue (lbf-in) : TS25=8.9, CS350860T=31, SETS51=31, TS43=31, SETS61=44, HFC03006=13, HFC04008=19
Note 1) The screw-on type has no shim. The holder has an in-built lead angle. Please select a holder with the appropriate lead angle.
Note 2) The minimum cutting diameter indicates the prepared hole diameter, not the nominal thread diameter.
MMTIR102-0.50-1.5-C
102-0.50-2.5-C
102-0.60-1.5-C
102-0.60-2.5-C
MMTIR103-0.75-1.5-C
103-0.75-2.5-C
123-0.90-1.5-C
163-1.15-1.5-C
203-1.45-1.5-C
MMTIR124-0.95-1.5-C
124-0.95-2.5-C
164-1.20-1.5-C
204-1.50-1.5-C
244-1.75-1.5-C
1.5
2.5
1.5
2.5
1.5
2.5
1.5
1.5
1.5
1.5
2.5
1.5
1.5
1.5
.625
.625
.625
.625
.625
.625
.750
1.000
1.250
.750
.750
1.000
1.250
1.500
5.000
5.000
6.000
6.000
6.000
6.000
7.000
10.000
10.000
7.000
7.000
8.000
10.000
12.000
1.000
1.000
1.250
1.250
1.500
1.500
1.500
2.500
2.000
2.000
2.000
1.500
2.000
2.500
.340
.340
.380
.380
.480
.480
.510
.660
.810
.610
.610
.700
.860
.980
.586
.586
.586
.586
.586
.586
.711
.937
1.187
.711
.711
.937
1.187
1.437
.500
.500
.600
.600
.750
.750
.900
1.150
1.450
.950
.950
1.200
1.500
1.750
1
1
1
1
2
2
3
3
4
2
2
4
4
4
THREADING
L3
D1
*
*
SHIM
Lead Angle
(%)
Order Number
1.5
0.5
0.5
1.5
2.5
3.5
4.5
CTI32TN15
N05
P05
P15
P25
P35
P45
Stock Inclination
Angle
R
(')
3
2
1
0
1
2
3
a
a
a
a
a
a
a
Stock Inclination
Angle
R
(')
Applicable
Holder
Lead Angle
(%)
Order Number
MMTIR
oo3-ooo
-oo-C
1.5
0.5
0.5
1.5
2.5
3.5
4.5
CTI43TN15
N05
P05
P15
P25
P35
P45
a
a
a
a
a
a
a
Insert Size
MMT11
2
MMT16
3
MMT22
4
Min. Cutting Diameter (inch)

0.50 .500 1.15 1.150
0.60 .600 1.20 1.200
0.75 .750 1.45 1.450
0.90 .900 1.50 1.500
0.95 .950 1.75 1.750
3
2
1
0
1
2
3
Applicable
Holder
Insert
MMTIR
oo4-ooo
-oo-C
Inclination
Angle
(')
Shim

See page G025 for shim selection guide lines.
IDENTIFICATION
Designation
Application
Internal
I
Hand of Tool
Right
R
Shank Diameter (inch)

.625
10
.750
12
1.000
16
1.250
20
1.500
24
Lead Angle
1.5
1.5
2.5
2.5
Coolant
C
With

Work Material
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180 280HB
Stainless Steel
< 200HB
Grade
Cutting Speed (SFM)
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF
VP20RT
490 (230 755)

330 (195 460)
260 (195 330)
460 (260 655)
330 (195 460)
260 (195 330)
425 (260 590)
260 (130 395)
195 (130 260)
Work Material
Cast Iron
H
Hardness
Grade
Cutting Speed (SFM)
Tensile Strength
VP10MF
VP15TF
VP10MF
VP15TF
VP10MF
VP15TF
VP10MF
VP15TF
460 (260 655)

295 (195 395)
150 ( 50 230)
100 ( 65 130)
195 (130 260)
150 ( 80 210)
165 (100 230)
130 ( 65 195)
< 350MPa
Titanium Alloy
Hardened Steel
45 55HRC
G013
THREADING
MMT M-CLASS INSERTS WITH 3-D CHIP BREAKERS

Dimensions (mm)
American UN
BSPT
THREADING
ISO Metric
VP15TF
Order Number
VP20RT
Type
Coated
MMT16ERA60-S
16ERG60-S
MMT16ERA55-S
16ERG55-S
MMT16ER100ISO-S
16ER125ISO-S
16ER150ISO-S
16ER175ISO-S
16ER200ISO-S
16ER250ISO-S
16ER300ISO-S
MMT16ER160UN-S
16ER140UN-S
16ER120UN-S
MMT16ER190W-S
16ER140W-S
16ER110W-S
MMT16ER190BSPT-S
16ER140BSPT-S
16ER110BSPT-S
Pitch
Geometry
D1
S1
Z1
Z2
Re
48 16
14 8
9.525
9.525
3.44
3.44
0.8
1.2
0.9
1.7
0.06
0.23

Partial form
48 16
14 8
9.525
9.525
3.44
3.44
0.8
1.2
0.9
1.7
0.07
0.23

Partial form
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
0.7
0.8
0.8
0.9
1.0
1.1
1.2
0.9
1.0
1.1
0.7
0.9
1.0
1.2
1.3
1.5
1.6
1.1
1.2
1.4
0.13
0.16
0.20
0.22
0.26
0.33
0.40
0.23
0.26
0.30
0.61
0.77
0.92
1.07
1.23
1.53
1.84
0.97
1.11
1.30
Full form
16
14
12
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
19
14
11
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
1.0
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
Full form
19
14
11
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
0.9
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
Full form
mm
thread/inch
0.5 1.5
1.75 3.0
Total
depth
of cut
(mm)
1.0
1.25
1.5
1.75
2.0
2.5
3.0
a
a
a
s
s
s
s
Full form
IDENTIFICATION
S M-class inserts with 3-D chip breakers
Designation
Circle (mm)
6.35
11
9.525
16
G014
Hand of Tool
Right
R
Application
E External
Internal
I
Pitch
100
1.0mm
125
1.25mm
150
1.5mm
175
1.75mm
200
2.0mm
250
2.5mm
300
3.0mm
a : Inventory maintained. s : Inventory maintained in Japan.

0.5 1.5mm
or
48 16 thread/inch
1.75 3.0mm
or
14 8 thread/inch
Threading Type
60 Partial Prole 60
55 Partial Prole 55
ISO ISO Metric
BSPT BSPT
UN American UN
INTERNAL THREADING INSERTS

VP15TF
MMT11IRA60-S
16IRA60-S
16IRG60-S
MMT11IRA55-S
16IRA55-S
16IRG55-S
MMT11IR100ISO-S
11IR125ISO-S
11IR150ISO-S
16IR100ISO-S
16IR125ISO-S
16IR150ISO-S
16IR175ISO-S
16IR200ISO-S
16IR250ISO-S
16IR300ISO-S
MMT16IR160UN-S
16IR140UN-S
16IR120UN-S
MMT16IR190W-S
16IR140W-S
16IR110W-S
MMT16IR190BSPT-S
16IR140BSPT-S
16IR110BSPT-S
VP20RT
Type
ISO Metric
American UN
BSPT
Order Number
a
a
Pitch
a
a
a
s
s
s
s
Z1
Z2
Re
Geometry
mm
thread/inch
48 16
48 16
14 8
6.35
9.525
9.525
3.04
3.44
3.44
0.8
0.8
1.2
0.9
0.9
1.7
0.03
0.03
0.11

Partial form
48 16
48 16
14 8
6.35
9.525
9.525
3.04
3.44
3.44
0.8
0.8
1.2
0.9
0.9
1.7
0.07
0.07
0.21

Partial form
3.04
3.04
3.04
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
0.6
0.8
0.8
0.6
0.8
0.8
0.9
1.0
1.1
1.1
0.9
0.9
1.1
0.7
0.9
1.0
0.7
0.9
1.0
1.2
1.3
1.5
1.5
1.1
1.2
1.4
0.06
0.08
0.10
0.06
0.08
0.10
0.11
0.13
0.17
0.20
0.11
0.12
0.14
0.58
0.72
0.87
0.58
0.72
0.87
1.01
1.15
1.44
1.73
0.92
1.05
1.22
Full form
16
14
12
6.35
6.35
6.35
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
19
14
11
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
1.0
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
Full form
19
14
11
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
0.9
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
Full form
S1
0.5 1.5
0.5 1.5
1.75 3.0
D1
Total
depth
of cut
(mm)
1.0
1.25
1.5
1.0
1.25
1.5
1.75
2.0
2.5
3.0
Full form
THREADING
Dimensions (mm)
Coated
G015
THREADING
MMT G-CLASS GROUND INSERTS
6g
Dimensions (mm)
Coated
Order Number
VP10MF
VP15TF
Type
ISO Metric
THREADING
Thread
Tolerance
MMT16ERA60
16ERG60
16ERAG60
22ERN60
s s
MMT16ERA55
16ERG55
16ERAG55
22ERN55
s s
MMT16ER050ISO
16ER075ISO
16ER100ISO
16ER125ISO
16ER150ISO
16ER175ISO
16ER200ISO
16ER250ISO
16ER300ISO
22ER350ISO
22ER400ISO
22ER450ISO
22ER500ISO
s s
s
s
Pitch
a s
a s
a s
a s
a s
a s
a s
s
s
s
s
Z1
Z2
Re
48 16
14 8
48 8
75
9.525
9.525
9.525
12.7
3.44
3.44
3.44
4.64
0.8
1.2
1.2
1.7
0.9
1.7
1.7
2.5
0.05
0.27
0.08
0.53

Partial form
48 16
14 8
48 8
7 5
9.525
9.525
9.525
12.7
3.44
3.44
3.44
4.64
0.8
1.2
1.2
1.7
0.9
1.7
1.7
2.5
0.05
0.21
0.07
0.44

Partial form
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
12.7
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
4.64
0.6
0.6
0.7
0.8
0.8
0.9
1.0
1.1
1.2
1.6
1.6
1.7
1.7
0.4
0.6
0.7
0.9
1.0
1.2
1.3
1.5
1.6
2.3
2.3
2.4
2.5
0.06
0.10
0.16
0.19
0.23
0.21
0.31
0.32
0.46
0.45
0.52
0.58
0.63
0.31
0.46
0.61
0.77
0.92
1.07
1.23
1.53
1.84
2.15
2.45
2.76
3.07
0.5 1.5
1.75 3.0
0.5 3.0
3.5 5.0
S1
thread/inch
Geometry
D1
mm
s s
Total
depth
of cut
(mm)
0.5
0.75
1.0
1.25
1.5
1.75
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Full form
IDENTIFICATION
MMT
16
G016
050
Hand of Tool
Right
R
Designation
Circle (mm)
6.35
11
9.525
16
22 12.7
Application
E External
Internal
I
ISO
Pitch
050
075
100
125
150
175
200
250
300
350
400
450
500
0.5mm
0.5 1.5mm
0.75mm A
or
48 16 thread/inch
1.0mm
1.25mm
1.75 3.0mm
1.5mm
or
G
1.75mm
14 8 thread/inch
2.0mm
0.5 3.0mm
2.5mm
or
AG
3.0mm
48 8 thread/inch
3.5mm
4.0mm
3.5 5.0mm
or
N
4.5mm
7 5 thread/inch
5.0mm

Threading Type
60 Partial Prole 60
55 Partial Prole 55
ISO ISO Metric
BSPT BSPT
UN American UN
RD Round DIN 405
TR ISO Trapezoidal 30
ACME American ACME
UNJ UNJ
APBU API Buttress Casing
APRD API Round Casing &Tubing
NPT NPT
NPTF NPTF
6H
Order Number
MMT11IRA60
16IRA60
16IRG60
16IRAG60
22IRN60
s s
MMT11IRA55
16IRA55
16IRG55
16IRAG55
22IRN55
s s
MMT11IR050ISO
11IR075ISO
11IR100ISO
11IR125ISO
11IR150ISO
11IR175ISO
11IR200ISO
16IR050ISO
16IR075ISO
16IR100ISO
16IR125ISO
16IR150ISO
16IR175ISO
16IR200ISO
16IR250ISO
16IR300ISO
22IR350ISO
22IR400ISO
22IR450ISO
22IR500ISO
s s
s s
s
s
Pitch
s
s
s
s
a s
a s
a s
a s
a s
a s
a s
s
s
s
s
Re
Geometry
48 16
48 16
14 8
48 8
75
6.35
9.525
9.525
9.525
12.7
3.04
3.44
3.44
3.44
4.64
0.8
0.8
1.2
1.2
1.7
0.9
0.9
1.7
1.7
2.5
0.05
0.05
0.16
0.05
0.30

Partial form
48 16
48 16
14 8
48 8
7 5
6.35
9.525
9.525
9.525
12.7
3.04
3.44
3.44
3.44
4.64
0.8
0.8
1.2
1.2
1.7
0.9
0.9
1.7
1.7
2.5
0.05
0.05
0.21
0.07
0.44

Partial form
6.35
6.35
6.35
6.35
6.35
6.35
6.35
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
12.7
3.04
3.04
3.04
3.04
3.04
3.04
3.04
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
4.64
0.6
0.6
0.6
0.8
0.8
0.9
0.9
0.6
0.6
0.6
0.8
0.8
0.9
1.0
1.1
1.1
1.6
1.6
1.6
1.6
0.4
0.6
0.7
0.9
1.0
1.1
1.1
0.4
0.6
0.7
0.9
1.0
1.2
1.3
1.5
1.5
2.3
2.3
2.4
2.3
0.03
0.04
0.10
0.12
0.14
0.10
0.18
0.03
0.04
0.10
0.12
0.14
0.10
0.18
0.15
0.26
0.22
0.25
0.28
0.32
0.29
0.43
0.58
0.72
0.87
1.01
1.15
0.29
0.43
0.58
0.72
0.87
1.01
1.15
1.44
1.73
2.02
2.31
2.60
2.89
s s
Z2
thread/inch
s s
Z1
mm
s s
s s
S1
0.5 1.5
0.5 1.5
1.75 3.0
0.5 3.0
3.5 5.0
s s
D1
Total
depth
of cut
(mm)
0.5
0.75
1.0
1.25
1.5
1.75
2.0
0.5
0.75
1.0
1.25
1.5
1.75
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Full form
THREADING
Dimensions (mm)
Coated
VP10MF
VP15TF
Type
ISO Metric
Thread
Tolerance
IDENTIFICATION
MMT
16
050
Hand of Tool
Right
R
Designation
Circle (mm)
6.35
11
9.525
16
22 12.7
Application
E External
Internal
I
ISO
Pitch
050
075
100
125
150
175
200
250
300
350
400
450
500
0.5mm
0.5 1.5mm
0.75mm A
or
48 16 thread/inch
1.0mm
1.25mm
1.75 3.0mm
1.5mm
or
G
1.75mm
14 8 thread/inch
2.0mm
0.5 3.0mm
2.5mm
or
AG
3.0mm
48 8 thread/inch
3.5mm
4.0mm
3.5 5.0mm
or
N
4.5mm
7 5 thread/inch
5.0mm
Threading Type
60 Partial Prole 60
55 Partial Prole 55
ISO ISO Metric
BSPT BSPT
UN American UN
RD Round DIN 405
TR ISO Trapezoidal 30
ACME American ACME
UNJ UNJ
APBU API Buttress Casing
APRD API Round Casing &Tubing
NPT NPT
NPTF NPTF
G017
THREADING
Medium Class A
2A
Standard BSPT
7h
Dimensions (mm)
Coated
Order Number
MMT16ER320UN
16ER280UN
16ER240UN
16ER200UN
16ER180UN
16ER160UN
16ER140UN
16ER130UN
16ER120UN
16ER110UN
16ER100UN
16ER090UN
16ER080UN
22ER070UN
22ER060UN
22ER050UN
MMT16ER280W
16ER260W
16ER200W
16ER190W
16ER180W
16ER160W
16ER140W
16ER120W
16ER110W
16ER100W
16ER090W
16ER080W
22ER070W
22ER060W
22ER050W
MMT16ER280BSPT
16ER190BSPT
16ER140BSPT
16ER110BSPT
VP10MF
VP15TF
Type
American UN
Round DIN 405
BSPT
THREADING
G018
Thread
Tolerance
a
a
a
a
a
a s
a s
a
a s
a
a
a
a
s
s
s
s
s
s
s s
s
s
s s
s
s s
s
s
s
s
s
s
s
s s
s s
s s
Pitch
mm
D1
S1
Z1
Z2
Re
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
9.525
9.525
9.525
9.525
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
3.44
3.44
3.44
3.44
0.6
0.6
0.7
0.8
0.8
0.9
1.0
1.0
1.1
1.1
1.1
1.2
1.2
1.6
1.6
1.7
0.6
0.7
0.8
0.8
0.8
0.9
1.0
1.1
1.1
1.1
1.2
1.2
1.6
1.6
1.7
0.6
0.8
1.0
1.1
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.5
1.7
1.6
2.3
2.3
2.5
0.7
0.8
0.9
1.0
1.0
1.1
1.2
1.4
1.5
1.5
1.7
1.5
2.3
2.3
2.4
0.6
0.9
1.2
1.5
0.09
0.10
0.16
0.19
0.21
0.24
0.22
0.24
0.32
0.29
0.32
0.35
0.48
0.47
0.53
0.64
0.09
0.10
0.18
0.19
0.20
0.23
0.26
0.30
0.33
0.37
0.34
0.39
0.46
0.53
0.66
0.09
0.14
0.26
0.33
thread/inch
32
28
24
20
18
16
14
13
12
11
10
9
8
7
6
5
28
26
20
19
18
16
14
12
11
10
9
8
7
6
5
28
19
14
11
Total
depth
of cut
(mm)
0.49
0.56
0.65
0.78
0.87
0.97
1.11
1.20
1.30
1.42
1.56
1.73
1.95
2.22
2.60
3.12
0.58
0.63
0.81
0.86
0.90
1.02
1.16
1.36
1.48
1.63
1.81
2.03
2.32
2.71
3.25
0.58
0.86
1.16
1.48
Geometry
Full form
Full form
Z1
S1
MMT16ER100RD
16ER080RD
16ER060RD
22ER040RD
s
s
s
s
10
8
6
4
9.525
9.525
9.525
9.525

3.44
3.44
3.44
3.44
1.1
1.4
1.5
2.2
1.2
1.3
1.7
2.3
0.60
0.75
1.00
1.51
1.27
1.59
2.12
3.18
55
Z2 Re
Full form
Full form
D1
Medium Class A
MMT11IR320UN
11IR280UN
11IR240UN
11IR200UN
11IR180UN
11IR160UN
11IR140UN
16IR320UN
16IR280UN
16IR240UN
16IR200UN
2B
16IR180UN
16IR160UN
16IR140UN
16IR130UN
16IR120UN
16IR110UN
16IR100UN
16IR090UN
16IR080UN
22IR070UN
22IR060UN
22IR050UN
MMT11IR190W
11IR140W
16IR280W
16IR260W
16IR200W
16IR190W
16IR180W
16IR160W
16IR140W
16IR120W
16IR110W
16IR100W
16IR090W
16IR080W
22IR070W
22IR060W
22IR050W
MMT11IR190BSPT
11IR140BSPT
16IR190BSPT
16IR140BSPT
16IR110BSPT
MMT16IR100RD
16IR080RD
16IR060RD
7H
22IR040RD
VP10MF
VP15TF
Order Number
s
s
s
s
s
s
s
a
a
a
a
a
a s
a s
a
a s
a
a
a
a
s
s
s
s
s
s
s
s
s s
s
s
s s
s
s s
s
s
s
s
s
s
s
s
s s
s s
s s
s
s
s
s
Pitch
mm
Total
depth
of cut
(mm)
Geometry
D1
S1
Z1
Z2
Re
32
28
24
20
18
16
14
32
28
24
20
18
16
14
13
12
11
10
9
8
7
6
5
19
14
28
26
20
19
18
16
14
12
11
10
9
8
7
6
5
19
14
19
14
11
6.35
6.35
6.35
6.35
6.35
6.35
6.35
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
6.35
6.35
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
6.35
6.35
9.525
9.525
9.525
3.04
3.04
3.04
3.04
3.04
3.04
3.04
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
3.04
3.04
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
3.04
3.04
3.44
3.44
3.44
0.6
0.6
0.7
0.8
0.8
0.9
0.9
0.6
0.6
0.7
0.8
0.8
0.9
0.9
1.0
1.1
1.1
1.1
1.2
1.1
1.6
1.6
1.6
0.8
0.9
0.6
0.7
0.8
0.8
0.8
0.9
1.0
1.1
1.1
1.1
1.2
1.2
1.6
1.6
1.7
0.8
0.9
0.8
1.0
1.1
0.6
0.7
0.8
0.9
1.0
1.1
1.1
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.5
1.7
1.5
2.3
2.3
2.3
1.0
1.1
0.7
0.8
0.9
1.0
1.0
1.1
1.2
1.4
1.5
1.5
1.7
1.5
2.3
2.3
2.4
0.9
1.0
0.9
1.2
1.5
0.04
0.05
0.09
0.11
0.12
0.14
0.11
0.04
0.05
0.09
0.11
0.12
0.14
0.11
0.10
0.18
0.13
0.15
0.17
0.27
0.23
0.26
0.32
0.19
0.26
0.09
0.10
0.18
0.19
0.20
0.23
0.26
0.30
0.33
0.37
0.34
0.39
0.46
0.53
0.66
0.14
0.26
0.14
0.26
0.33
0.46
0.52
0.61
0.73
0.81
0.92
1.05
0.46
0.52
0.61
0.73
0.81
0.92
1.05
1.13
1.22
1.33
1.47
1.63
1.83
2.09
2.44
2.93
0.86
1.16
0.58
0.63
0.81
0.86
0.90
1.02
1.16
1.36
1.48
1.63
1.81
2.03
2.32
2.71
3.25
0.86
1.16
0.86
1.16
1.48
Full form
10
8
6
4
9.525
9.525
9.525
12.7
3.44
3.44
3.44
4.64
1.1
1.4
1.4
2.2
1.2
1.4
1.5
2.3
0.55
0.70
0.93
1.40
1.27
1.59
2.12
3.18
Full form
thread/inch
Full form
THREADING
Dimensions (mm)
Coated
Standard BSPT
Type
American UN
BSPT
Round DIN 405
Thread
Tolerance
Full form
G019
THREADING
7e
3G
Standard NPT
Standard API RD
Standard API
3A
Class 2
Dimensions (mm)
Coated
Order Number
VP10MF
Type
ISO Trapezoidal 30
American ACME
UNJ
American NPTF
American NPT
API Round Casing & Tubing API Buttress Casing
THREADING
G020
Thread
Tolerance
MMT16ER150TR
16ER200TR
16ER300TR
22ER400TR
22ER500TR
MMT16ER120ACME
16ER100ACME
16ER080ACME
22ER060ACME
22ER050ACME
MMT16ER320UNJ
16ER280UNJ
16ER240UNJ
16ER200UNJ
16ER180UNJ
16ER160UNJ
16ER140UNJ
16ER120UNJ
16ER100UNJ
16ER080UNJ
MMT22ER050APBU
MMT16ER100APRD
16ER080APRD
MMT16ER270NPT
16ER180NPT
16ER140NPT
16ER115NPT
16ER080NPT
MMT16ER270NPTF
16ER180NPTF
16ER140NPTF
16ER115NPTF
16ER080NPTF
s
s
s
s
a
a
a
a
s
s
s
s
s
s
s
s
s
a
a
a
a
s
s
s
s
Pitch
mm
Total
depth
of cut
(mm)
Geometry
D1
S1
Z1
Z2
Re
9.525
9.525
9.525
12.7
12.7
3.44
3.44
3.44
4.64
4.64
1.0
1.1
1.3
1.7
2.1
1.1
1.3
1.5
1.9
2.5
0.08
0.15
0.15
0.15
0.15
0.90
1.25
1.75
2.25
2.75
Semi-full form
12
10
8
6
5
9.525
9.525
9.525
12.7
12.7
3.44
3.44
3.44
4.64
4.64
1.1
1.3
1.4
1.8
2.0
1.2
1.4
1.5
2.1
2.3
0.08
0.08
0.10
0.10
0.10
1.19
1.52
1.84
2.37
2.79
Semi-full form
32
28
24
20
18
16
14
12
10
8
5
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
0.6
0.7
0.7
0.8
0.8
0.9
1.0
1.1
1.2
1.2
3.1
0.7
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.5
1.6
1.9
0.13
0.14
0.17
0.20
0.22
0.25
0.29
0.33
0.40
0.51
0.18
0.46
0.52
0.61
0.73
0.81
0.92
1.05
1.22
1.47
1.83
1.55
Full form
10
8
9.525
9.525
3.44
3.44
1.2
1.3
1.4
1.5
0.34
0.41
1.41
1.81
Full form
27
18
14
11.5
8
9.525
9.525
9.525
9.525
9.525
3.44
3.44
3.44
3.44
3.44
0.7
0.8
0.9
1.1
1.3
0.8
1.0
1.2
1.5
1.8
0.04
0.08
0.09
0.11
0.14
0.66
1.01
1.33
1.64
2.42
Full form
27
18
14
11.5
8
9.525
9.525
9.525
9.525
9.525
3.44
3.44
3.44
3.44
3.44
0.7
0.8
0.9
1.1
1.3
0.8
1.0
1.2
1.5
1.8
0.04
0.04
0.04
0.04
0.04
0.64
1.00
1.35
1.63
2.38
Full form
thread/inch
1.5
2.0
3.0
4.0
5.0

Full form
7H
3G
Dimensions (mm)
Coated
Order Number
VP10MF
MMT16IR150TR
16IR200TR
16IR300TR
22IR400TR
22IR500TR
MMT16IR120ACME
16IR100ACME
16IR080ACME
22IR060ACME
22IR050ACME
s
s
s
s
a
a
a
a
Pitch
mm
12
10
8
6
5
Geometry
D1
S1
Z1
Z2
Re
9.525
9.525
9.525
12.7
12.7
3.44
3.44
3.44
4.64
4.64
1.0
1.1
1.3
1.7
2.1
1.1
1.3
1.5
1.9
2.5
0.08
0.15
0.15
0.15
0.15
0.90
1.25
1.75
2.25
2.75
Semi-full form
9.525
9.525
9.525
12.7
12.7
3.44
3.44
3.44
4.64
4.64
1.2
1.2
1.4
1.8
2.0
1.3
1.3
1.5
2.1
2.3
0.05
0.08
0.10
0.10
0.10
1.19
1.52
1.84
2.37
2.79
Semi-full form
thread/inch
1.5
2.0
3.0
4.0
5.0
Total
depth
of cut
(mm)
Class 2
Standard NPT
Standard API RD
Standard API
When machining an internal UNJ thread, cut an internal hole with the appropriate diameter.
Then machine with 60 American UN. In this case, a full form type insert cannot be used.
MMT22IR050APBU
MMT16IR100APRD
16IR080APRD
10
8
MMT16IR270NPT
16IR180NPT
16IR140NPT
16IR115NPT
16IR080NPT
MMT16IR140NPTF
16IR115NPTF
16IR080NPTF
a
a
a
a
s
s
12.7
4.64
2.8
1.9
0.18
1.55
Full form
9.525
9.525
3.44
3.44
1.2
1.3
1.4
1.5
0.34
0.41
1.41
1.81
Full form
27
18
14
11.5
8
9.525
9.525
9.525
9.525
9.525
3.44
3.44
3.44
3.44
3.44
0.7
0.8
0.9
1.1
1.3
0.8
1.0
1.2
1.5
1.8
0.04
0.08
0.09
0.11
0.14
0.66
1.01
1.33
1.64
2.42
Full form
14
11.5
8
9.525
9.525
9.525
3.44
3.44
3.44
0.9
1.1
1.3
1.2
1.5
1.8
0.04
0.04
0.04
1.35
1.63
2.38
Full form
THREADING
Type
American NPTF
American NPT
API Round Casing & Tubing API Buttress Casing
UNJ
American ACME ISO Trapezoidal 30
Thread
Tolerance
G021
THREADING
THREADING METHODS
Right Hand Thread
Left Hand Thread
EXTERNAL
*change the shim
INTERNAL
*change the shim
Usually, threads are cut feeding the insert towards the chuck.
When machining left hand threads, note that clamping rigidity is lowered due the application of back turning.
When machining left hand threads, the lead angle is negative. Ensure an appropriate lead angle by changing the shim.
INSERT TYPES
Partial Form
a The same insert can be used for a range of pitches.
a Shorter tool life because the nose radius of the
insert is smaller than that of a full form insert.
THREADING
Semi Full Form (Trapezoidal threads only)
Full Form
a No deburring needed after threading.
a Requires specic insert for each thread
form and pitch.
form and pitch.
a Finishing with another operation may be necessary.

Crest Radius
(Additional turning necessary to nish the thread crest.)
a Finishing with another operation may be necessary.

Crest Radius
(Finished by insert form.)
Pre-nished Surface
Feed Direction
Insert
Crest Radius
(Additional turning necessary to nish the thread crest.)
Finished
Surface
Finished
Surface
Pre-nished Surface
a No de-burring needed after threading.

a Requires specic insert for each thread
Finished Surface
Pre-nished
Surface
Finishing
allowance
Feed Direction
Insert
Feed Direction
Insert
INFEED METHODS
1 5
Radial Infeed
Flank Infeed
G022
Disadvantages
Features
Advantages
a Easiest to use.
Modied Flank Infeed
a Relatively easy to use.

(Standard programme for
(Semi-standard programme
threading)
for threading.)
a Wide application. (Cutting
a Reduced cutting force.
conditions easy to change.)
a Suitable for large pitch
threads or materials that
a Uniform wear of the right and
left sides of the cutting edge.
peel easily.
a Good chip discharge.
a Preventing ank wear on the
a Difcult chip control.

a Subject to vibration in the later
a Complex machining
a Large ank wear of the right
side of a cutting edge.

passes due to long cutting
a Relatively difcult to change
edge in contact with workpiece.
cutting depth.
(Re-programming
a Ineffective for large pitch
threading.
necessary)
a Heavy load on the nose
radius.
Incremental Infeed
a Uniform wear of the right and

right side of the cutting edge.
left sides of the cutting edge.
a Good for large pitch or
a Good for large pitch or
materials that peel easily.
materials that peel easily.
a Good chip discharge.
programming.
a Difcult to change cutting
depth. (NC programming
necessary)
a Complex machining
programming.
a Difcult to change cutting
depth. (Re-programming
necessary)
a Chip control is difcult.
THREADING DEPTH
Features
Advantages
V1
X2
Disadvantages
Easy to use.
(Standard program for threading.)
Long chips generated during the

nal pass.
Superior resistance to vibration.

(Constant cutting force.)
Complex calculation of cutting

depth when changing the number
of passes.
Reduced load on nose radius

during the rst half of the passes.
Subject to vibration in the later

stages of cutting.
(Increased cutting force)
Fixed cut area
X1
Easy chip control.

(Optional setting of chip thickness)
Fixed cutting depth
In some cases, changing the NC

program is necessary.
Good chip control.
THREADING
X2
Easy to calculate cutting depth

when changing the number of
passes.
* It is recommended to set the depth of cut of the nal pass to 0.05mm ~ 0.025mm.
Large cutting depths can cause vibration, leading to a poor surface nish.
aFormulas
yFormulas to calculate infeed for each pass in a reduced series.
Example) External threading (ISO metric)
Pitch : 1.0mm
ap : 0.6mm
nap : 5
: Depth of cut
: Actual pass
: Total depth of cut
: Number of passes
: 1st pass 0.3
2nd pass 21=1
3rd pass 31=2
1st pass
2nd pass
3rd pass
4th pass
nth pass
5th pass
aNC Program for Modied Flank Infeed

yExample:- M121.0 5 passes modied 1-3
External Threading
(mm)
Internal Treading
G023
THREADING
RECOMMENDED CUTTING METHODS AND CONDITIONS

Selecting Cutting Conditions
Priority
Tool life
Threading
methods
Cutting force
Surface nish
Precision of thread
Radial
Flank
Chips discharge
Fixed cut area 2
u
u
Fixed cutting depth

Cutting depth
Efciency
(Reduced passes)
u : 1st recommendation
1 Tool life and surface nish accuracy can be increased by changing the threading method from ank infeed to modied ank infeed.
2 Chip control can be improved by increasing the cutting depth in the later half of passes.
Cutting depth and the number of passes
THREADING
ySelection of the appropriate cutting depth

and the right number of passes is vital for
threading.
Feature and benets of Mitsubishi products

Insert grades, specially produced for threading tools, ensure
highly efcient cutting by enabling high-speed machining and
a reduced number of passes.
For most threading, use a "threading cycle program," which

has originally been installed on machines, and specify "total
cutting depth" and "cutting depth in the rst or nal pass."
Cutting depth and the number of passes are easy to change
for the radial infeed method, thus making it easy to determine
the appropriate cutting conditions.
Machining Cost
Reduction
Advice on improved threading

yIncreasing tool life
yTo achieve highly efcient machining
To prevent damage to the nose radius Recommended method - Modied ank infeed.
Increase cutting speed. (Dependant on the maximum

revolution and rigidity of the machine.)
To have uniform ank wear on both sides of a cutting edge Recommended method - Radial infeed
Reduce the number of passes. (Reduce by 30-40%.)
To prevent crater wear Recommended method - Flank infeed
yPreventing chip problems
A reduced number of passes can improve chip discharge

because of the thicker chips generated.
yPreventing vibration
Change to ank or modied infeed.
Change to ank or modied infeed.
During radial infeed cutting, use an inverted holder and

change the coolant supply to a downward direction.
When using radial infeed, reduce cutting depth in the later

half of passes and lower the cutting speed.
When using the radial infeed method, set the minimum

cutting depth at around .008 inch to make the chips thicker.
Tangled chips during internal threading can damage the
insert. In these cases, pause slightly away from the start
point and clear the chips with coolant before every pass.
Change to M-class inserts with a 3-D chip breaker.
G024
yIncreased surface nish accuracy

A nal pass should be performed at the same depth of cut
as the last regular pass.
When using the ank infeed method, change to radial infeed
only during the nal pass.
Lead angle (%)

Inclination angle (')
Selecting a Shim for the MMT Series

yFlank angle and lead angle
Lead angle (%) depends on a combination of thread diameter and pitch.
Select a shim so that the lead angle of the thread can coincide with the ank angles of the
thread and insert ($1, $2). No need to change a shim for general threading with an
MMT holder. When threading with a small diameter or large pitch, change the shim
depending on the lead angle, referring to the table and graph below. When threading left
hand threads, change to a shim with a negative inclination angle.
Fla
nk
yShim reference table (Threading diameter)

Right Hand Thread (mm)
0.5
0.75
1
1.25
1.5
1.75
2
2.5
3
3.5
4
4.5
5
<&1.9
<&2.9
<&3.8
<&4.8
<&5.7
<&6.7
<&7.6
<&9.5
<&11.4
<&13.3
<&15.2
<&17.1
<&19.0
4.5
&1.9
&2.9
&3.8
&4.8
&5.7
&6.7
&7.6
&9.5
&11.4
&13.3
&15.2
&17.1
&19.0
&2.2
&3.2
&4.3
&5.4
&6.5
&7.6
&8.6
&10.8
&13.0
&15.1
&17.3
&19.4
&21.6
3.5
&2.2
&3.2
&4.3
&5.4
&6.5
&7.6
&8.6
&10.8
&13.0
&15.1
&17.3
&19.4
&21.6
Left Hand Thread (mm)
2.5
&2.8
&4.3
&5.7
&7.1
&8.5
&9.9
&11.4
&14.2
&17.0
&19.9
&22.7
&25.6
&28.4
&2.8
&4.3
&5.7
&7.1
&8.5
&9.9
&11.4
&14.2
&17.0
&19.9
&22.7
&25.6
&28.4
1.5
&4.3
&6.5
&8.7
&10.9
&13.0
&15.2
&17.4
&21.7
&26.0
&30.4
&34.7
&39.1
&43.4
&4.3
&6.5
&8.7
&10.9
&13.0
&15.2
&17.4
&21.7
&26.0
&30.4
&34.7
&39.1
&43.4
yShim reference graph

Right Hand Thread
%=1.5 (Standard shim)

4
5
6
7
%=0.5
3
2
10
14
18
24
32
1
50
(1.97")
0.5
>&11.4
<&4.3
>&11.4
&11.4
&4.3 &11.4
>&17.1
<&6.5
>&17.1
&17.1
&6.5 &17.1
>&22.8
<&8.7
>&22.8
&22.8
&8.7 &22.8
>&28.5 <&10.9 &10.9 &28.5
>&28.5
&28.5
>&34.2 <&13.0 &13.0 &34.2
>&34.2
&34.2
>&39.9 <&15.2 &15.2 &39.9
>&39.9
&39.9
>&45.6 <&17.4 &17.4 &45.6
>&45.6
&45.6
>&57.0 <&21.7 &21.7 &57.0
>&57.0
&57.0
>&68.4 <&26.0 &26.0 &68.4
>&68.4
&68.4
>&79.8 <&30.4 &30.4 &79.8
>&79.8
&79.8
>&91.2 <&34.7 &34.7 &91.2
>&91.2
&91.2
&102.3 >&102.6 <&39.1 &39.1 &102.6 >&102.6
&114.0 >&114.0 <&43.4 &43.4 &114.0 >&114.0
(Note) Back turning in the case of left hand threads.
100
150
(3.94")
(5.91")
Threading diameter (mm)
: Lead angle
9
Threading Pitch (mm)
1.5
10
%=2.5
7
Pitch (mm)
: Lead angle
Threading Pitch (thread/inch)
9 Threading
8 impossible
Threading
impossible
0.5
Left Hand Thread
%=4.5 %=3.5
10
gle
an 1)
($
200
(7.87")
%=1.5
Threading
impossible
7
6
5
6
7
%=0.5
10
Treading Pitch (thread/inch)
Threading
impossible
Pitch
(mm)
nk
Fla
THREADING
Lead
Angle
ang
l
($2 e
)
14
18
24
32
1
0
50
(1.97")
100
150
(3.94")
(5.91")
Threading diameter (mm)
200
(7.87")
Note) When a thread lead angle < the tool ank angle, change the shim to prevent side interference with the insert.
(Refer to the table below for the calculation of thread lead angle and tool ank angle.)
When replacing a shim, check if the difference between

the thread lead angle and shim inclination angle is
within:2.5 - 0.5 where thread angle is 60 (55 ) 2 1 where thread angle is 30 (29)
* Inclination angle of a standard shim is 0.
* The holder has a 1.5 lead angle.
yCalculation of thread lead angle
tan%=
nP
)d = )d
I
n
P
d
: Lead angle
: Lead
: Number of thread starts
: Pitch
: Pitch diameter
of thread
yExample of selecting a shim

When the thread lead angle is 2.2
zIn the case when the thread angle is 60
(2.2 lead angle) (2.5 - 0.5) = 0.3 - 1.7 shim inclination angle is appropriate.
Threading with a standard shim (0 inclination angle) is possible. But, replacing
with a shim with a 1 inclination angle is recommended, refer to Standard Shim
List on pages 9 and 10.
xIn the case when the thread angle is 30
(2.2 lead angle) (2 - 1) = 0.2 - 1.2 shim inclination angle is appropriate.
Replacing with a shim with a 1 inclination angle is recommended, referring to
Standard Shim List on pages 9 and 10.
yRelief angle of an insert set on a holder

Thread helix angle
Internal relief angle
External relief angle
60
55
30
29
8.5
7
4
4
6
7
2.5
2.5
Relief angles ($2, $1) of an insert become small when

the thread helix angle of a trapezoidal, round, or other
thread is small. Take care when selecting a shim.
G025
THREADING
Standard of Depth of Cut (External Threading)
EXTERNAL (RADIAL INFEED)
yISO Metric
Pitch Total
Cutting
(mm)
Depth
0.5
0.75
1.0
1.25
1.5
1.75
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0.31
0.46
0.61
0.77
0.92
1.07
1.23
1.53
1.84
2.15
2.45
2.76
3.07
(mm)
Number of Passes
0.10
0.16
0.18
0.19
0.22
0.22
0.24
0.26
0.27
0.33
0.34
0.38
0.42
0.08
0.14
0.15
0.17
0.21
0.21
0.23
0.23
0.25
0.30
0.31
0.34
0.38
0.07
0.10
0.12
0.14
0.17
0.16
0.17
0.19
0.20
0.24
0.24
0.28
0.32
0.06
0.06
0.10
0.11
0.14
0.13
0.16
0.17
0.18
0.21
0.22
0.24
0.27
0.06
0.10
0.12
0.11
0.14
0.15
0.16
0.18
0.19
0.22
0.24
0.06
0.06
0.09
0.12
0.13
0.14
0.17
0.17
0.20
0.22
0.09
0.11
0.12
0.13
0.15
0.16
0.18
0.20
0.06
0.06
0.11
0.12
0.14
0.14
0.16
0.18
Insert Type
0.11
0.12
0.14
0.14
0.16
0.18
10
0.06
0.11
0.12
0.13
0.15
0.17
11
0.10
0.11
0.12
0.14
0.16
12
13
14
0.06
0.06
0.12 0.11 0.06
0.13 0.12 0.06
0.15 0.12 0.06
inserts with
G-class ground inserts M-class
3-D chip breakers
MMT16ER050ISO
16ER075ISO
16ER100ISO MMT16ER100ISO-S
16ER125ISO
16ER125ISO-S
16ER150ISO
16ER150ISO-S
16ER175ISO
16ER175ISO-S
16ER200ISO
16ER200ISO-S
16ER250ISO
16ER250ISO-S
16ER300ISO
16ER300ISO-S
22ER350ISO
22ER400ISO
22ER450ISO
22ER500ISO
yAmerican UN
THREADING
Pitch Total
(thread/ Cutting
inch() Depth
32
28
24
20
18
16
14
13
12
11
10
9
8
7
6
5
.019
.022
.026
.031
.034
.038
.044
.047
.051
.056
.061
.068
.077
.087
.102
.123
(inch)
Number of Passes
.007
.007
.007
.008
.009
.009
.009
.010
.011
.011
.011
.013
.014
.015
.017
.017
.006
.006
.006
.007
.008
.008
.008
.009
.009
.009
.009
.011
.012
.013
.014
.015
.004
.004
.006
.005
.006
.006
.006
.007
.007
.007
.007
.009
.009
.011
.011
.012
.002
.003
.005
.005
.005
.005
.005
.006
.006
.006
.006
.007
.007
.009
.010
.011
.002
.002
.004
.004
.004
.005
.005
.006
.006
.006
.006
.006
.008
.008
.009
.002
.002
.004
.005
.005
.005
.006
.006
.006
.006
.007
.007
.009
.002
.004
.003
.005
.005
.005
.005
.006
.006
.007
.008
.002
.002
.002
.004
.005
.005
.006
.006
.006
.007
Insert Type
.002
.004
.004
.005
.005
.006
.007
10
.002
.002
.004
.005
.005
.007
11
12
13
14
.002
.002
.005 .004 .002
.007 .006 .006 .002
inserts with
3-D chip breakers
MMT16ER320UN
16ER280UN
16ER240UN
16ER200UN
16ER180UN
16ER160UN
16ER140UN
16ER130UN
16ER120UN
16ER110UN
16ER100UN
16ER090UN
16ER080UN
22ER070UN
22ER060UN
22ER050UN
MMT16ER160UN-S
16ER140UN-S
MMT16ER120UN-S
yWhitworth for BSW, BSP

Pitch Total
(thread/ Cutting
inch() Depth
28
26
20
19
18
16
14
12
11
10
9
8
7
6
5
.023
.025
.032
.034
.035
.040
.046
.054
.058
.064
.071
.080
.091
.107
.128
(inch)
Number of Passes
.007
.007
.008
.008
.010
.008
.009
.011
.011
.011
.011
.012
.013
.014
.017
.006
.006
.007
.007
.007
.007
.008
.010
.009
.010
.010
.011
.013
.013
.016
.004
.005
.006
.006
.006
.006
.007
.008
.008
.008
.008
.009
.010
.011
.014
.004
.005
.005
.006
.005
.005
.006
.006
.007
.007
.007
.007
.009
.009
.011
.002
.002
.004
.005
.005
.004
.005
.006
.006
.006
.006
.007
.008
.008
.010
.002
.002
.002
.004
.005
.006
.006
.006
.006
.006
.007
.008
.009
.004
.004
.005
.005
.005
.006
.006
.007
.007
.009
.002
.002
.002
.005
.005
.005
.006
.006
.007
.008
Insert Type
.002
.004
.005
.005
.006
.006
.007
10
.002
.005
.005
.006
.006
.007
11
.002
.004
.004
.006
.007
12
13
14
.002
.002
.005 .005 .002
.006 .005 .002
inserts with
3-D chip breakers
MMT16ER280W
16ER260W
16ER200W
16ER190W
16ER180W
16ER160W
16ER140W
16ER120W
16ER110W
16ER100W
16ER090W
16ER080W
22ER070W
22ER060W
22ER050W
MMT16ER190W-S
MMT16ER140W-S
MMT16ER110W-S
(Note) Set the nishing allowance on a diameter at approx. .004 inch when using a full form insert.
Please note the cutting depth and the number of passes when a nose radius of a partial or semi-full form insert or of an internal threading insert is
small to prevent damage to the insert nose.
Please set the cutting depth sufciently deep enough on materials such as hardened steel or austenitic stainless steel to help prevent premature
wear and chipping caused by the outer layer of the material.
G026
yBSPT
(inch)
28
19
14
11
.023
.034
.046
.058
Number of Passes
.007
.009
.009
.010
.006
.007
.008
.009
.004
.006
.007
.008
.004
.005
.006
.007
Insert Type
.002
.005 .002
.005 .005 .004 .002
.006 .006 .005 .005 .002
G-class ground inserts
M-class inserts with

3-D chip breakers
MMT16ER280BSPT
16ER190BSPT
16ER140BSPT
16ER110BSPT
MMT16ER190BSPT-S
16ER140BSPT-S
16ER110BSPT-S
yRound DIN 405

Pitch Total
(thread/ Cutting
inch() Depth
10
8
6
4
.050
.063
.083
.125
(inch)
Number of Passes
.009
.009
.010
.013
.008
.008
.010
.013
.008
.008
.009
.013
.007
.007
.009
.012
.006
.007
.008
.011
.005
.006
.007
.010
.005
.006
.007
.009
Insert Type
10
11
12
13
14
.002
.005 .005 .002
.006 .006 .005 .004 .002
.009 .008 .007 .007 .006 .005 .002
MMT16ER100RD
16ER080RD
16ER060RD
22ER040RD
yISO Trapezoidal 30
Pitch Total
Cutting
(mm)
Depth
1.5
2.0
3.0
4.0
5.0
0.90
1.25
1.75
2.25
2.75
(mm)
Number of Passes
0.23
0.29
0.32
0.33
0.35
0.21
0.26
0.31
0.32
0.32
0.16
0.21
0.24
0.24
0.26
0.13
0.17
0.19
0.22
0.24
0.11
0.14
0.18
0.21
0.22
0.06
0.12
0.17
0.17
0.21
Insert Type
10
11
12
13
14
0.06
0.15 0.13 0.06
0.16 0.15 0.14 0.13 0.12 0.16
0.19 0.19 0.17 0.15 0.14 0.13 0.12 0.06
MMT16ER150TR
16ER200TR
16ER300TR
22ER400TR
22ER500TR
yAmerican ACME
Pitch Total
(thread/ Cutting
inch() Depth
12
10
8
6
5
.047
.060
.072
.093
.110
(inch)
Number of Passes
.011
.011
.012
.013
.014
.009
.010
.010
.012
.013
.008
.008
.009
.011
.012
.007
.007
.007
.009
.010
.006
.006
.006
.008
.009
.004
.006
.006
.007
.008
.002
.005
.006
.006
.007
.005
.005
.006
.007
Insert Type
10
11
12
13
14
.002
.005 .004 .002
.005 .005 .004 .005 .002
.006 .006 .006 .005 .005 .002
MMT16ER120ACME
16ER100ACME
16ER080ACME
22ER060ACME
22ER050ACME
yUNJ
(inch)
Pitch Total
(thread/ Cutting
inch() Depth
32
28
24
20
18
16
14
12
10
8
.018
.020
.024
.029
.032
.036
.041
.048
.058
.072
Number of Passes
.006
.006
.007
.007
.009
.010
.010
.011
.012
.012
.006
.005
.006
.006
.007
.008
.009
.011
.011
.012
.004
.004
.006
.005
.006
.006
.007
.008
.008
.009
.002
.003
.003
.005
.004
.005
.005
.007
.006
.007
.002
.002
.004
.004
.004
.004
.005
.005
.006
.002
.002
.003
.004
.004
.005
.006
Insert Type
10
11
.002
.002
.005 .004 .002
.005 .005 .004 .004 .002
MMT16ER320UNJ
16ER280UNJ
16ER240UNJ
16ER200UNJ
16ER180UNJ
16ER160UNJ
16ER140UNJ
16ER120UNJ
16ER100UNJ
16ER080UNJ
yAPI Buttress Casing

Pitch Total
(thread/ Cutting
inch() Depth
THREADING
Pitch Total
(thread/ Cutting
inch() Depth
(inch)
Number of Passes
Insert Type
10
11
.061 .010 .009 .007 .006 .005 .005 .005 .004 .004 .004 .002
MMT22ER050APBU
G027
THREADING
Standard of Depth of Cut (External Threading)

EXTERNAL (RADIAL INFEED)
yAPI Round Casing & Tubing
Pitch Total
(thread/ Cutting
inch() Depth
10
8
(inch)
Number of Passes
Insert Type
10
11
12
.056 .010 .009 .006 .006 .005 .005 .005 .004 .004 .002
.071 .010 .009 .007 .006 .006 .006 .005 .005 .005 .005 .005 .002
MMT16ER100APRD
16ER080APRD
yAmerican NPT
Pitch Total
(thread/ Cutting
inch() Depth
27
18
14
11.5
8
.026
.040
.052
.065
.095
(inch)
Number of Passes
.006
.008
.009
.009
.013
.005
.006
.007
.007
.011
.005
.006
.006
.007
.009
.004
.005
.006
.006
.008
.004
.005
.005
.006
.007
.002
.004
.005
.005
.006
.004
.004
.005
.006
Insert Type
10
11
12
13
14
15
.002
.004 .004 .002
.005 .005 .004 .004 .002
.006 .005 .005 .005 .004 .004 .004 .002
MMT16ER270NPT
16ER180NPT
16ER140NPT
16ER115NPT
16ER080NPT
yAmerican NPTF
THREADING
Pitch Total
(thread/ Cutting
inch() Depth
G028
27
18
14
11.5
8
Number of Passes
.025 .006
.007
.009
.009
.013
.039
.053
.064
.094
(inch)
.006
.006
.008
.009
.011
.004
.006
.006
.007
.009
.004
.005
.006
.006
.007
.003
.005
.005
.005
.007
.002
.004
.005
.005
.006
.004
.004
.005
.006
Insert Type
10
11
12
13
14
15
.002
.004 .004 .002
.004 .004 .004 .004 .002
.006 .005 .005 .005 .004 .004 .004 .002
MMT16ER270NPTF
16ER180NPTF
16ER140NPTF
16ER115NPTF
16ER080NPTF
Standard of Depth of Cut (Internal Threading)

INTERNAL (RADIAL INFEED)
yISO Metric
0.5
0.75
1.0
1.25
1.5
1.75
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0.29
0.43
0.58
0.72
0.87
1.01
1.15
1.44
1.73
2.02
2.31
2.60
2.89
Number of Passes
0.09
0.15
0.17
0.18
0.21
0.21
0.24
0.25
0.26
0.32
0.33
0.36
0.41
0.07
0.13
0.15
0.16
0.20
0.20
0.22
0.24
0.25
0.30
0.31
0.33
0.38
0.07
0.09
0.11
0.12
0.16
0.15
0.18
0.21
0.22
0.23
0.24
0.28
0.32
0.06
0.06
0.09
0.11
0.13
0.12
0.14
0.15
0.17
0.19
0.22
0.24
0.27
0.06
0.09
0.11
0.10
0.12
0.13
0.14
0.17
0.18
0.21
0.24
0.06
0.06
0.09
0.10
0.12
0.13
0.15
0.15
0.19
0.21
0.08
0.09
0.10
0.12
0.14
0.14
0.16
0.18
0.06
0.06
0.09
0.11
0.13
0.13
0.15
0.16
0.09
0.10
0.12
0.12
0.14
0.15
Insert Type
10
0.06
0.09
0.11
0.12
0.13
0.14
11
0.08
0.10
0.11
0.12
0.13
12
13
14

3-D chip breakers
MMT11IR050ISO MMT16IR050ISO
11IR075ISO
16IR075ISO
11IR100ISO
16IR100ISO MMT11IR100ISO-S MMT16IR100ISO-S
11IR125ISO
16IR125ISO
11IR125ISO-S
16IR125ISO-S
11IR150ISO
16IR150ISO
11IR150ISO-S
16IR150ISO-S
11IR175ISO
16IR175ISO
16IR175ISO-S
11IR200ISO
16IR200ISO
16IR200ISO-S
16IR250ISO
16IR250ISO-S
0.06
16IR300ISO
16IR300ISO-S
0.06
22IR350ISO
0.10 0.10 0.06
22IR400ISO
0.12 0.11 0.06
22IR450ISO
0.12 0.12 0.06
22IR500ISO
yAmerican UN
Pitch Total
(thread/ Cutting
inch() Depth
32
28
24
20
18
16
14
13
12
11
10
9
8
7
6
5
.018
.020
.024
.029
.032
.036
.041
.044
.048
.052
.058
.064
.072
.082
.096
.115
(inch)
Number of Passes
.006
.006
.007
.007
.008
.008
.008
.009
.009
.009
.010
.012
.012
.014
.016
.016
.006
.005
.006
.006
.007
.007
.007
.007
.009
.009
.009
.009
.010
.012
.013
.014
.004
.004
.005
.005
.006
.006
.006
.006
.007
.008
.008
.008
.008
.009
.010
.012
.002
.003
.004
.005
.005
.005
.005
.006
.006
.006
.006
.007
.007
.008
.009
.010
.002
.002
.004
.004
.004
.005
.005
.005
.005
.005
.006
.006
.007
.007
.009
.002
.002
.004
.004
.005
.005
.005
.005
.006
.006
.007
.007
.008
.002
.004
.004
.005
.004
.005
.005
.006
.006
.006
.008
.002
.002
.002
.004
.004
.005
.005
.006
.006
.007
.002
.004
.004
.005
.006
.006
.007
Insert Type
10
.002
.002
.005
.005
.005
.006
11
.002
.002
.005
.006
12
13
14
MMT11IR320UN
11IR280UN
11IR240UN
11IR200UN
11IR180UN
11IR160UN
11IR140UN
.004 .002
.005 .005 .002
MMT16IR320UN
16IR280UN
16IR240UN
16IR200UN
16IR180UN
16IR160UN
16IR140UN
16IR130UN
16IR120UN
16IR110UN
16IR100UN
16IR090UN
16IR080UN
22IR070UN
22IR060UN
22IR050UN

3-D chip breakers
MMT16IR160UN-S
16IR140UN-S
MMT16IR120UN-S
yWhitworth for BSW, BSP

Pitch Total
(thread/ Cutting
inch() Depth
28
26
20
19
18
16
14
12
11
10
9
8
7
6
5
.023
.025
.032
.034
.035
.040
.046
.054
.058
.064
.071
.080
.091
.107
.128
THREADING
Pitch Total
Cutting
(mm)
Depth
(mm)
(inch)
Number of Passes
.007
.007
.008
.008
.010
.008
.009
.011
.011
.011
.011
.012
.013
.014
.017
.006
.006
.007
.007
.007
.007
.008
.010
.009
.010
.010
.011
.013
.013
.016
.004
.005
.006
.006
.006
.006
.007
.008
.008
.008
.008
.009
.010
.011
.014
.004
.005
.005
.006
.005
.005
.006
.006
.007
.007
.007
.007
.009
.009
.011
.002
.002
.004
.005
.005
.004
.005
.006
.006
.006
.006
.007
.008
.008
.010
.002
.002
.002
.004
.005
.006
.006
.006
.006
.006
.007
.008
.009
.004
.004
.005
.005
.005
.006
.006
.007
.007
.009
.002
.002
.002
.004
.005
.005
.006
.006
.007
.008
.002
.004
.005
.005
.006
.006
.007
Insert Type
10
.002
.005
.005
.006
.006
.007
11
.002
.004
.004
.006
.007
12
.002
.002
.005
.006
13
14

3-D chip breakers
MMT16IR280W
16IR260W
16IR200W
MMT11IR190W
16IR190W MMT16IR190W-S
16IR180W
16IR160W
MMT11IR140W
16IR140W MMT16IR140W-S
16IR120W
16IR120W-S
16IR110W
16IR100W
16IR090W
16IR080W
22IR070W
.005 .002
22IR060W
.005 .002
22IR050W
G029
THREADING
Standard of Depth of Cut (Internal Threading)
INTERNAL (RADIAL INFEED)
yBSPT
Pitch Total
(thread/ Cutting
inch() Depth
19
14
11
(inch)
Number of Passes
Insert Type
.034 .009 .007 .006 .005 .005 .002

.046 .009 .008 .007 .006 .005 .005 .004 .002
.058 .010 .009 .008 .007 .006 .006 .005 .005 .002

3-D chip breakers
MMT11IR190BSPT MMT16IR190BSPT
11IR140BSPT
16IR140BSPT
16IR110BSPT
MMT16IR190BSPT-S
16IR140BSPT-S
16IR110BSPT-S
yRound DIN 405

Pitch Total
(thread/ Cutting
inch() Depth
10
8
6
4
.050
.063
.083
.125
(inch)
Number of Passes
.009
.009
.010
.013
.008
.008
.010
.013
.008
.008
.009
.013
.007
.007
.009
.013
.006
.007
.008
.011
.005
.006
.007
.010
.005
.006
.007
.009
Insert Type
10
11
12
13
14
.002
.005 .005 .002
.006 .006 .005 .004 .002
.009 .008 .007 .007 .006 .005 .002
MMT16IR100RD
16IR080RD
16IR060RD
22IR040RD
yISO Trapezoidal 30
THREADING
Pitch Total
Cutting
(mm)
Depth
1.5
2
3
4
5
0.90
1.25
1.75
2.25
2.75
(mm)
Number of Passes
0.23
0.29
0.32
0.33
0.35
0.21
0.26
0.31
0.32
0.32
0.16
0.21
0.24
0.24
0.26
0.13
0.17
0.19
0.22
0.24
0.11
0.14
0.18
0.21
0.22
0.06
0.12
0.17
0.17
0.21
Insert Type
10
11
12
13
14
0.06
0.15 0.13 0.06
0.16 0.15 0.14 0.13 0.12 0.06
0.19 0.19 0.17 0.15 0.14 0.13 0.12 0.06
MMT16IR150TR
16IR200TR
16IR300TR
22IR400TR
22IR500TR
yAmerican ACME
Pitch Total
(thread/ Cutting
inch() Depth
12
10
8
6
5
.047
.060
.072
.093
.110
(inch)
Number of Passes
.011
.011
.012
.013
.014
.009
.010
.010
.012
.013
.008
.008
.009
.011
.012
.007
.007
.007
.009
.010
.006
.006
.006
.008
.009
.004
.006
.006
.007
.008
.002
.005
.006
.006
.007
.005
.005
.006
.007
Insert Type
10
11
12
13
14
.002
.005 .004 .002
.005 .005 .005 .004 .002
.006 .006 .006 .005 .005 .002
MMT16IR120ACME
16IR100ACME
16IR080ACME
22IR060ACME
22IR050ACME
yAPI Buttress Casing

Pitch Total
(thread/ Cutting
inch() Depth
(inch)
Number of Passes
Insert Type
10
11
.061 .010 .009 .007 .006 .005 .005 .005 .004 .004 .004 .002
MMT22IR050APBU
yAPI Round Casing & Tubing

Pitch Total
(thread/ Cutting
inch() Depth
10
8
(inch)
Number of Passes
Insert Type
10
11
12
.056 .010 .009 .006 .006 .005 .005 .005 .004 .004 .002
.071 .010 .009 .007 .006 .006 .006 .005 .005 .005 .005 .005 .002
MMT16IR100APRD
16IR080APRD
G030
y American NPT
Pitch Total
(thread/ Cutting
inch() Depth
27
18
14
11.5
8
.026
.040
.052
.065
.095
(inch)
Number of Passes
.006
.008
.009
.009
.013
.005
.006
.007
.007
.011
.005
.006
.006
.007
.009
.004
.005
.006
.006
.008
.004
.005
.005
.006
.007
.002
.004
.005
.005
.006
.004
.004
.005
.006
Insert Type
10
11
12
13
14
15
.002
.004 .004 .002
.005 .005 .004 .004 .002
.006 .005 .005 .005 .004 .004 .004 .002
MMT16IR270NPT
16IR180NPT
16IR140NPT
16IR115NPT
16IR080NPT
y American NPTF
Pitch Total
(thread/ Cutting
inch() Depth
(inch)
Number of Passes
Insert Type
10
11
12
13
14
15
14 .053 .009 .008 .006 .006 .005 .005 .004 .004 .004 .002
11.5 .064 .009 .009 .007 .006 .005 .005 .005 .004 .004 .004 .004 .002
8 .094 .013 .011 .009 .007 .007 .006 .006 .006 .005 .005 .005 .004 .004 .004 .002
MMT16IR140NPTF
16IR115NPTF
16IR080NPTF
THREADING
G031
THREADING
TROUBLESHOOTING
Problems
Observation
Low thread precision.
Threads do not mesh

with each other.
Incorrect tool installation.
Shallow thread.
Incorrect depth of cut.
Modify the depth of cut.
Lack of insert wear or plastic

deformation resistance.
Refer to "Quickly generated ank wear." and "Large

plastic deformation." below.
Chips wrap around or clog the work

pieces.
Change to ank infeed and control the chip

discharge direction.
Poor surface nish.
Surface damage.
Causes
Solutions
Set the insert center height at 0".
Check holder inclination (Lateral).
Change to an M-class insert with a 3-D chip breaker.
Surface tears.
The side of the insert cutting edge

interferes with the workpiece.
Check the lead angle and select an appropriate

shim.
Built-up edge (Welding).
Increase cutting speed.

Increase coolant pressure and volume.
Surface vibrations.
THREADING
Short tool life.
Cutting resistance too high.
Decrease depth of cut per pass.
Cutting speed too high.
Decrease the cutting speed.
Insufcient work piece or tool

clamping.
Re-check work piece and tool clamping. (Chuck

pressure, clamping allowance)
Incorrect tool installation.
Set the insert center height at 0".
Cutting speed too high.
Too many passes causes abrasive wear.
Reduce the number of passes.
Small depth of cut for the nishing

pass.
Do not re-cut at 0" depth of cut. Depth of cut larger

than .002" is recommended.
Non-uniform wear of
the right and left sides
of the cutting edge.
The work piece lead angle and the

tool lead angle do not match.
Check the work piece lead angle and select an

appropriate shim.
Chipping and fracture.
Cutting speed too low.
Increase cutting speed.
Increase the number of passes and decrease the

cutting resistance per pass.
Unstable clamping.
Check work piece deection.
Flank wear quickly

generated.
Shorten tool overhang.

Recheck work piece and tool clamping. (Chuck
pressure, clamping allowance)
Chip packing.
Increase coolant pressure to blow away chips.

Change the tool pass to control chips. (Lengthen
each pass to allow the coolant to clear the chips.
Change from standard internal cutting to back
turning to prevent chip jamming.
Large plastic
deformation.
Non-chamfered work pieces causes high

resistance at the start of each pass.
Chamfer the workpiece entry and exit faces .
High cutting speed and large heat generation.
Lack of coolant supply.
Check coolant is supply is sufcient.

Increase coolant pressure and volume.
G032
Increase the number of passes and decrease the

cutting resistance per pass.
Memo
G033
THREADING
MTVO HOLDER
MTVO
a Screw-on type.
a Positive insert products good nish.
a Applicable to narrow grooving and threading.
External grooving, Threading
Max. Groove Depth
Order Number
Insert Number
R L
MTVOR/L-8-3B
10-3B
12-3B
12-4B
16-4D
16-5D
20-4D
H1
a a
32p
a a
a a
a a
TNMC
Max.
Groove
Depth
(inch)
ap
Dimensions (inch)
Stock
L1
L2
F1
Insert Screw Clamp Screw Clamp
.500 4.500 1.000

.625 4.500 1.000
.750 .057 / .156

.875 .057 / .156
GTS1
XNS35
CL6
32p
.500
.625
GTS1
XNS35
CL6
32p
.750
.750 4.500 1.000 1.000 .057 / .156
GTS1
XNS35
CL6
43p
.750
.750 4.500 1.063 1.000 .156 / .234
GTS2
XNS36
CL6
a a
43p
1.000 1.000 6.000 1.063 1.250 .156 / .234
GTS2
XNS36
CL6
a a
54p
43p
1.000 1.000 6.000 1.250 1.250

.297
1.250 1.250 6.000 1.063 1.500 .156 / .234
GTS3
XNS36
CL6
GTS2
XNS36
CL6
a a
INSERTS (THREADING)
Order Number
TNMC32NV
43NV
54NV
Class
THREADING
E
E
E
Coated
Stock
Cermet Carbide
UP20M
NX55
UTi20T
Dimensions (inch)
Min.
Pitch
(T.P.I)
D1
S1
Re
8
6
4
.375
.500
.625
.125
.187
.250
.004
.004
.004
Geometry
Order Number
TNMC32NGR032
32NGL032
32NGR063
32NGL063
43NGR063
43NGL063
43NGR094
43NGL094
43NGR125
43NGL125
43NGR156
43NGL156
54NGR187
54NGL187
G034
a
r
Class
INSERTS (GROOVING)
Coated
Stock
Cermet Carbide
Dimensions (inch)
W3
D1
S1
L3
Re
.032
.032
.375
.375
.125
.125
.057
.057
< .003
.063
.375
.125
.156
< .003
.063
.375
.125
.156
< .003
.063
.500
.188
.156
< .003
.063
.500
.188
.156
< .003
.094
.500
.188
.156
< .003
.094
.500
.188
.156
< .003
.125
.500
.188
.234
< .003
.125
.500
.188
.234
< .003
.156
.500
.188
.234
< .003
.156
.500
.188
.234
< .003
E
E
.625
.625
.250
.250
.297
.297
< .003
.187
.187
UP20M
NX55
UTi20T
E
E
Geometry
< .003
< .003
STHN/O TYPE
S-STHN/O
a Screw-on type.
ap
ap
F1
D4
RR
L1
D1
D4
L1
F1
RR
32p
1.000
10.000
.656
10
1.250
.060 / .156
GTS1
TKY10F
43p
1.250
12.000
.843
10
1.750
.156 / .234
GTS2
TKY20F
43p
1.500
14.000
.968
10
2.250
.156 / .234
GTS2
TKY20F
a a
43p
2.000
14.000
1.218
10
3.000
.156 / .234
GTS2
TKY20F
a a
54p
2.000
14.000
1.250
4.000
.297
GTS3
TKY20F
Order Number
Insert Number
R L
S16-STHNR/L-3
S20-STHNR/L-4
S24-STHNR/L-4
S32-STHNR/L-4
S32-STHOR/L-5
Max.
Groove
Depth
(inch)
ap
Min.
Cutting
Diameter
(inch)
D1
Dimensions (inch)
Stock
a a
a a
a a
TNMC
Clamp Screw Wrench
TNMC32NV
43NV
54NV
E
E
E
Coated
Stock
Cermet Carbide
UP20M
NX55
UTi20T
Dimensions (inch)
Min.
Pitch
(T.P.I)
D1
S1
Re
8
6
4
.375
.500
.625
.125
.187
.250
.004
.004
.004
Geometry
THREADING
Order Number
Class
INSERTS (THREADING)
Order Number
TNMC32NGR032
32NGL032
32NGR063
32NGL063
43NGR063
43NGL063
43NGR094
43NGL094
43NGR125
43NGL125
43NGR156
43NGL156
54NGR187
54NGL187
Class
INSERTS (GROOVING)
Coated
Stock
Cermet Carbide
Dimensions (inch)
W3
D1
S1
L3
Re
.032
.032
.375
.375
.125
.125
.057
.057
< .003
.063
.375
.125
.156
< .003
.063
.375
.125
.156
< .003
.063
.500
.188
.156
< .003
.063
.500
.188
.156
< .003
.094
.500
.188
.156
< .003
.094
.500
.188
.156
< .003
.125
.500
.188
.234
< .003
.125
.500
.188
.234
< .003
.156
.500
.188
.234
< .003
.156
.500
.188
.234
< .003
E
E
.625
.625
.250
.250
.297
.297
< .003
.187
.187
UP20M
NX55
UTi20T
E
E
Geometry
< .003
< .003
G035
THREADING
a Min. cutting diameter 10mm.
a Screw-on type.
a Max. groove depth: 3mm.
F TYPE
FSL51

D4
F1
F1
2
L2
L1
10
H1
L2
L1
Metric Standard
Stock
Min.
Max.
Cutting Groove
Diameter Depth
(mm)
(mm) Clamp
Wrench
Screw
10
1.0 TS25 TKY08F
Dimensions (mm)
Insert Number
Order Number
FSL5108R
5110R
5112R
5114R
5116R
Grooving
MLG
10ppL
10ppL
14ppL
Threading
MLT
Boring
1001L
1001L
H1
L1
L2
F1
W3
1.2
1.5
2.0
1.5
2.0
3.0
2.0
3.0
4.0
1004L
125
30
4.8
1004L
10
150
40
5.8
1404L
12
10.8
180
50
6.8
1404L
14
12.4
180
60
7.8
16
14
200
70
9.7
MLG
14ppL
FSL52
MLT
1401L
MLP
D4
1401L
MLP
12
1.0
TS25 TKY08F
14
2.0
TS32 TKY08F
16
2.0
TS32 TKY08F
20
3.0
TS43 TKY15F
Carbide shank
D4
F1
F1
THREADING
L2
L1
10
H1
L2
L1
Metric Standard
Stock
Dimensions (mm)
Insert Number
FSL5208R
5210R
5212R
5214R
5216R
Grooving
MLG
10ppL
10ppL
MLT
1001L
1001L
MLP
D4
H1
L1
L2
F1
W3
1.2
1.5
2.0
1.5
2.0
3.0
2.0
3.0
4.0
1004L
125
60
4.8
1004L
10
150
70
5.8
1404L
12
10.8
180
80
6.8
14
12.4
180
85
7.8
16
14
200
115
9.7
14ppL
MLT
1401L
Boring
1404L
MLG
14ppL
Threading
1401L
D4
Order Number
R
D4
MLP
Min.
Max.
Cutting Groove
Diameter Depth
(mm)
(mm) Clamp
Wrench
Screw
10
1.0 TS25 TKY08F
12
1.0
TS25 TKY08F
14
2.0
TS32 TKY08F
16
2.0
TS32 TKY08F
20
3.0
TS43 TKY15F

Work Material
Hardness
Grade
Cutting Speed
(SFM)
Feed
(inch/rev)
P Carbon Steel
180 280HB
UP20M UTi20T
295 (195 390)
.002 (.0008 .003)
UP20M UTi20T
260 (165 330)
.001 (.0008 .0015)
Alloy Steel
G036
280 350HB

2 Corner type (S-SL5NR08 / 10 / 12)
1 Corner type (S-SL5NR05 / 06)
2
W3
D1
2
W3
L2
D1
D4
L1
(Min.Bore)
ap
10
ap
F1
S-SL5N
F1
F TYPE

a Screw-on type.
L2
L1
D4
(Min.Bore)
Dimensions (inch)
Insert Number
Grooving
Threading
D4
L1
L2
F1
W3
.062
.094
S-SL5NR05
MLG10WpppL
MLT1001L
.313
5.000
1.250
.188
06
MLG10WpppL
MLT1001L
.375
6.000
1.500
.219
08
MLG14WpppL
MLT1401L
.500
10
MLG20WpppL
MLT2001L
.625
8.000
3.000
.375
12
MLG20WpppL
MLT2001L
.750
10.000
4.000
.438
7.000
2.000
.281
.062
.094
.125
.094
.125
.156
Max.
Min.
Cutting Groove
Diameter Depth
(inch)
(inch)
ap
Clamp Screw Wrench
D1
.390
.039
TS25
TKY08F
.449
.039
TS25
TKY08F
.579
.079
TS32
TKY08F
.791
.118
TS43
TKY15F
.902
.118
TS43
TKY15F
THREADING
Order Number
Stock

Work Material
Hardness
Grade
Cutting Speed
(SFM)
Feed
(inch/rev)
P Carbon Steel
180 280HB
UP20M UTi20T
295 (195 390)
.002 (.0008 .003)
280 350HB
UP20M UTi20T
260 (165 330)
.001 (.0008 .0015)
Alloy Steel
INSERTS
G038
SPARE PARTS
M001
TECHNICAL DATA
N001
G037
THREADING
F TYPE

a Screw-on type.
INSERTS
UP20M
UTi20T
HTi10
Application
.062
MLG10W062L
.276 .197 .039 .094
.004
.094
10W094L
.276 .197 .039 .094
.004
Inch
Metric
Grooving
Inch
Metric
Order Number
L1
L2
L3
S1
Re
.047 (1.2mm)
MLG1012L
.276 .197 .039 .094
.004
.059 (1.5mm)
1015L
.276 .197 .039 .094
.004
.079 (2.0mm)
1020L
.276 .197 .039 .094
.004
.062
MLG14W062L
.465 .256 .079 .187
.004
.094
14W094L
.465 .256 .079 .187
.004
.125
14W125L
.465 .256 .079 .187
.004
.094
20W094L
.661 .356 .118 .250
.004
.125
20W125L
.661 .356 .118 .250
.004
.156
20W156L
.661 .356 .118 .250
.004
.059 (1.5mm)
MLG1415L
.465 .256 .079 .187
.004
.079 (2.0mm)
1420L
.465 .256 .079 .187
.004
.118 (3.0mm)
1430L
.465 .256 .079 .187
.004
.079 (2.0mm)
2020L
.661 .356 .118 .250
.004
.118 (3.0mm)
2030L
.661 .356 .118 .250
.004
.157 (4.0mm)
2040L
.661 .356 .118 .250
.004
Min.Pitch 13T.P.I
MLT1001L
.276 .197
.094 .004
Min.Pitch 11T.P.I
1401L
.465 .256
.187 .004
Min.Pitch 8T.P.I
2001L
.661 .356
.250 .004
MLP1004L
.276 .197 .039 .094 .016
1404L
.465 .248 .079 .187 .016
2004L
.661 .356 .118 .250 .016
Geometry
MLT1001L, MLP1004L
(1 Corner type)
MLT1401L /2001L
MLP1404L /2004L
(2 Corner type)
Boring
Threading
THREADING
Dimensions (inch)
Coated Carbide
Groove Width
(inch)
W3
G038
a
r

SPARE PARTS
M001
TECHNICAL DATA
N001
CT
D1
Z2
Z2
Z2
Z2
F2
F2
F1
F1
Re
Internal threading
D4
H1
L10
L1
L2
Without
Without
With
Without
Without
With
Without
Without
With
Without
Without
With
Threads
Unied Screw
Pitch
Thread
(thread/inch) D1
Metric Screw
Pitch
Thread (
mm)
> M4
> M4
> M4
> M6
> M6
> M6
> M8
> M8
> M8
> M10
> M10
> M10
0.5 1.0
> NO.8 32UNC
0.5 1.0
> NO.8 36UNF
0.5 1.0
0.75 1.25
> 1/4 20UNC
0.75 1.25
> 1/4 28UNF
0.75 1.25
0.75 1.5
> 5/16 18UNC
0.75 1.5
> 5/16 24UNF
0.75 1.5
0.75 1.75
> 3/8 16UNC
0.75 1.75
> 3/8 24UNF
0.75 1.75
36 24
36 24
36 24
28 20
28 20
28 20
24 18
24 18
24 18
24 16
24 16
24 16
3
3
3
4.5
4.5
4.5
6
6
6
7
7
7
Dimensions (mm)
Re
D4
L1
L10
L2
F1
Z2
F2
H1
0.03
0.03
0.03
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
3
3
3
4
4
4
5
5
5
6
6
6
50
50
50
60
60
60
70
70
70
75
75
75
5.2
10.2
10.2
7.6
15.6
15.6
11
21
21
11
21
21
6
6
6
7
7
7
8
8
8
8
8
8
1.3
1.3
1.3
1.8
1.8
1.8
2.3
2.3
2.3
2.8
2.8
2.8
0.6
0.6
0.6
0.8
0.8
0.8
1
1
1
1
1
1
1.2
1.2
1.2
1.7
1.7
1.7
2.2
2.2
2.2
2.2
2.2
2.2
2.7
2.7
2.7
3.6
3.6
3.6
4.5
4.5
4.5
5.4
5.4
5.4
THREAD PITCH FOR THE CT TYPE

0.50
0.70
1.50
1.75
36
32
Unied Thread
P (thread/inch)
28
24
20
18
16
Order Number
CT03RS-M4/M4B
CT04RS-M6/M6B
CT05RS-M8/M8B
CT06RS-M10/M10B
Metric Thread
P (mm)
0.75 0.80 1.00 1.25
THREADING
CT0305RS-M4
03RS-M4
03RS-M4B
0407RS-M6
04RS-M6
04RS-M6B
0511RS-M8
05RS-M8
05RS-M8B
0611RS-M10
06RS-M10
06RS-M10B
Breaker
Order Number
Min.
Cutting
Diameter
60
Stock
Micro Grain Coated
Carbide
TF15 VP15TF
(Note) For internal threads that are larger than the minimum diameter of the Micro Mini Twin (CT type) it is possible to machining the above
thread pitches. For the minimum diameter please refer to the standards.
DEPTH OF CUT FOR THE CT TYPE

32
28
24
20
18
16
P (thread/inch) 36
D.O.C. (inch) .0169 .0193 .0220 .0213 .0260 .0252 .0307 .0343 .0386
Re* (Corner radius) .0012 .0012 .0012 .0020 .0012 .0020 .0020 .0020 .0020
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0.06
0.05
0.05
0.04
0.04
0.03
0.03
0.06
0.06
0.06
0.05
0.05
0.04
0.04
0.04
0.03
0.06
0.06
0.06
0.05
0.05
0.04
0.04
0.04
0.03
0.03
0.06
0.06
0.05
0.05
0.05
0.04
0.04
0.03
0.03
0.03
0.06
0.06
0.06
0.05
0.05
0.04
0.04
0.04
0.03
0.03
0.03
0.07
0.07
0.06
0.06
0.05
0.05
0.05
0.04
0.04
0.04
0.03
0.03
0.03
0.07
0.07
0.06
0.06
0.06
0.05
0.05
0.04
0.04
0.04
0.03
0.03
0.07
0.07
0.07
0.07
0.06
0.06
0.06
0.05
0.05
0.05
0.04
0.04
0.04
0.03
0.07
0.07
0.07
0.07
0.07
0.06
0.06
0.06
0.05
0.05
0.05
0.05
0.04
0.04
0.04
0.04
0.03
0.07
0.07
0.07
0.07
0.07
0.07
0.06
0.06
0.06
0.06
0.05
0.05
0.05
0.05
0.04
0.04
0.04
0.04
0.04
0.03
Number of Passes
a Unied Thread
0.75
0.8
1
1.25 1.5 1.75
P (pitch) 0.5 0.7
D.O.C. (mm) 0.3 0.43 0.46 0.44 0.49 0.62 0.6 0.76 0.92 1.09
Re* (Corner radius) 0.03 0.03 0.03 0.05 0.03 0.03 0.05 0.05 0.05 0.05
Number of Passes
a Metric Thread
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
.0024
.0024
.0024
.0020
.0020
.0016
.0016
.0016
.0012
.0024
.0024
.0024
.0020
.0020
.0016
.0016
.0016
.0012
.0012
.0012
.0028
.0024
.0024
.0024
.0020
.0020
.0016
.0016
.0016
.0012
.0012
.0012
.0024
.0024
.0024
.0020
.0020
.0020
.0016
.0016
.0016
.0012
.0012
.0012
.0028
.0028
.0024
.0024
.0024
.0020
.0020
.0016
.0016
.0016
.0012
.0012
.0012
.0012
.0028
.0028
.0024
.0024
.0024
.0020
.0020
.0020
.0016
.0016
.0012
.0012
.0012
.0028
.0028
.0028
.0024
.0024
.0024
.0024
.0020
.0020
.0020
.0016
.0016
.0016
.0012
.0012
.0028
.0028
.0028
.0028
.0028
.0024
.0024
.0024
.0020
.0020
.0020
.0020
.0016
.0016
.0012
.0012
.0028
.0028
.0028
.0028
.0028
.0024
.0024
.0024
.0024
.0024
.0020
.0020
.0020
.0016
.0016
.0016
.0012
.0012
though the pitch maybe the same, the depth of cut varies according to the corner radius. For the Micro Mini Twin CT type CT03RS-M4,
* Even
and CT03RS-M4B the corner radius is 0.03mm(.0012inch), for other types it is 0.05mm(.0020inch). For further details please refer to the standards section.
G039
THREADING
HOLDER
Holder
MICRO-MINI TWIN
Machine Makers
Order Number
10252A
0407RS-M6, 04RS-M6(B)
10315A
0511RS-M8, 05RS-M8(B)
10378A
0611RS-M10, 06RS-M10(B)
10441A
RBH19030N
0305RS-M4, 03RS-M4(B)
19040N
0407RS-M6, 04RS-M6(B)
19050N
0511RS-M8, 05RS-M8(B)
19060N
0611RS-M10, 06RS-M10(B)
19070N
RBH16189A
0305RS-M4, 03RS-M4(B)
16252A
0407RS-M6, 04RS-M6(B)
16315A
0511RS-M8, 05RS-M8(B)
16378A
0611RS-M10, 06RS-M10(B)
16441A
ID : Metric Type
THREADING
Round Type Holder

& .750inch
Round Type Holder

& 1.000inch
0305RS-M4, 03RS-M4(B)
ID : Metric Type
Round Type Holder

& .625inch
CT
RBH10189A
ID : Metric Type
Type

NC lathes

NC lathes
Mitsubishi Materials obtained the makers' approval before entering their names in the list.

MICRO-MINI TWIN
CT type
Holder
(Note) For L10, refer to page G039(CTtype).

Work Material
Cutting Speed
(SFM)
General Steel
100 260
Stainless Steel
100 260
Cast Iron
100 260
165 330
(Note 1) Recommend wet machining.

(Note 2) Please remember when machining small diameters and high speeds there is the possibility that the machine can not keep up with the
set feed.
G040

Holder
MICRO-MINI TWIN
Machine Makers
Round Type Holder

& 16mm
Round Type Holder

& 20mm
Round Type Holder

& 22mm
Round Type Holder

& 25mm
Square Type Holder

r10mm
Order Number
CT
RBH1630N
0305RS-M4, 03RS-M4(B)
1640N
0407RS-M6, 04RS-M6(B)
1650N
0511RS-M8, 05RS-M8(B)
1660N
0611RS-M10, 06RS-M10(B)
1670N

NC lathes
RBH2030N
0305RS-M4, 03RS-M4(B)
2040N
0407RS-M6, 04RS-M6(B)
2050N
0511RS-M8, 05RS-M8(B)
2060N
0611RS-M10, 06RS-M10(B)
2070N

Tsugami Corporation
RBH2230N
0305RS-M4, 03RS-M4(B)
2240N
0407RS-M6, 04RS-M6(B)
2250N
0511RS-M8, 05RS-M8(B)
2260N
0611RS-M10, 06RS-M10(B)
2270N
NC lathes
STAR MICRONICS CO., LTD.

THREADING
Type
RBH2530N
0305RS-M4, 03RS-M4(B)
2540N
0407RS-M6, 04RS-M6(B)
Tsugami Corporation
2550N
0511RS-M8, 05RS-M8(B)
2560N
0611RS-M10, 06RS-M10(B)
NC lathes
2570N
SBH1030R
0305RS-M4, 03RS-M4(B)
1040R
0407RS-M6, 04RS-M6(B)
1050R
0511RS-M8, 05RS-M8(B)
1060R
0611RS-M10, 06RS-M10(B)
1070R
NC lathes
HOLDER
E034, E036, E037
SPARE PARTS
M001
TECHNICAL DATA
N001
G041
GUIDE TO HSK-T TOOLS

a Section
organization
zOrganized by product series.

FIGURE SHOWING
THE TOOLING APPLICATION
uses illustrations and arrows to depict available
machining applications along with cutting edge
lead angles.
PRODUCT TYPE
GEOMETRY
TITLE OF PRODUCT SERIES
CHIP BREAKER BY
CUTTING APPLICATION
PRODUCT SECTION
HSK-T TOOLS
FOR MULTI-TASK MACHINES

PCLN
Finish
External turning Facing
Light
FH
(4)
MA
(4)
Medium
Finish
(4)
(4)
Stainless
CBN
(4)
R L
s s
CNMo
CNGo
NP-CNoA
43o
Shim
LLSCN42
(4)
CBN
(4)
(4)
65 45 2.9
(4)
Stainless
(4)
Order Number
Shim Pin
Clamp
Lever
Clamp
Screw
Wrench
LLP14
LLCL14
LLCS108
HKY30R
H63TH-PCMNN-H12
-L12
Insert Number
CNMo
CNGo
NP-CNoA
s
s
43o
Dimensions
(mm) Mass
(lbs)
L1
100
140
(4)
*
Shim
3.7 LLSCN42
6.0 LLSCN42
Shim Pin
Clamp
Lever
LLP14
LLP14
LLCL14
LLCL14
Clamp
Screw
Plug
Wrench
LLCS108 HGM-PT1/8
LLCS108 HGM-PT1/8
HKY30R
HKY30R
* Clamp Torque (lbf-in) : LLCS108=29
DCLN
External turning
Facing
DOUBLE CLAMP type
Finish
FH
Light
(4)
Medium
MA
(4)
External turning
Facing
DOUBLE CLAMP type
Finish
FH
Light
MA
(4)
Medium
Semi-Heavy
Medium
GH
(4)
(4)
Medium
Standard
MH
95
Medium
SA
(4)
Medium
Standard
MH
DCMN
Medium
SA
Medium
Semi-Heavy
GH
95
(4)
(4)
Stainless
CBN
R L
H63TH-DCLNR/L-DX12
CNMo
s s CNGo
NP-CNoA
43o
Dimensions
(mm) Mass
(lbs)
L1 F1
65 45 2.9
(4)
(4)
(4)
*
Shim
LLSCN42
Shim Pin
LLP14
Clamp
Bridge
Spring
DCK2613
DCS1
Clamp
Screw
DC0621T
TKY20F
*
Cutting Mode
Finish Cutting
< 180HB
Light Cutting
Mild Steel
Medium Cutting
Finish Cutting
Carbon Steel
180HB 350HB
Light Cutting
Alloy Steel
Medium Cutting
Finish Cutting
M
< 200HB
Stainless Steel
Light Cutting
Medium Cutting
Light Cutting
K
Tensile Strength
Medium Cutting
Gray Cast Iron
< 350MPa
Semi-Heavy Cutting
(Note) Insert photo is an example. Letters show chip breaker style,
gures show inscribed circle.
(4)
s
s
CNMo
CNGo
NP-CNoA
43o
Dimensions
(mm) Mass
(lbs)
L1
100
140
(4)
*
Shim
3.7 LLSCN42
6.0 LLSCN42
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
LLP14
LLP14
DCK2613
DCK2613
DCS1
DCS1
DC0621T
DC0621T
TKY20F
TKY20F

Hardness
H63TH-DCMNN-H12
-L12
Insert Number
Wrench
Work Material
Order Number
Stock
Stock
Insert Number
(4)
CBN
MS
Order Number
(4)
Stainless
(4)
MS

Breaker
Grade
Cutting Speed (SFM)
FY
SY
MS
FH
SA
MA
FH
SA
MS
MA
Standard
Flat Top
NX3035
NX3035
UE6110
NX3035
UE6110
UE6110
US735
US735
US735
UC5115
UC5115
UC5115
850 1210
770 1100
850 1440
655 935
685 1160
620 1065
345 655
310 605
275 540
520 965
520 965
505 915
Work Material
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180HB 350HB
Stainless Steel
< 200HB
Gray Cast Iron
Tensile Strength
< 350MPa
Cutting Mode
Breaker
Grade
Cutting Speed (SFM)
Finish Cutting
Light Cutting
Medium Cutting
Finish Cutting
Light Cutting
Medium Cutting
Finish Cutting
Light Cutting
Medium Cutting
Light Cutting
Medium Cutting
Semi-Heavy Cutting
FY
SY
MS
FH
SA
MA
FH
SA
MS
MA
Standard
Flat Top
NX3035
NX3035
UE6110
NX3035
UE6110
UE6110
US735
US735
US735
UC5115
UC5115
UC5115
850 1210
770 1100
850 1440
655 935
685 1160
620 1065
345 655
310 605
275 540
520 965
520 965
505 915
PCLN type inserts
A068A073
PCMN type inserts
A068A073
DCLN type inserts
A068A073
DCMN type inserts
A068A073
SPARE PARTS
P001
CBN & PCD inserts
B022B024, B054
CBN & PCD inserts
B022B024, B054
TECHNICAL DATA
Q001
LEGEND FOR
STOCK STATUS MARK
REFERENCE PAGE
is shown on the left hand

page of each double-page
spread.
indicates reference pages for details

of inserts that are applicable to the
product.
H007
PAGE REFERENCE
SPARE PARTS
TECHNICAL DATA
indicates reference pages, including
the above, on the right hand page of
PRODUCT STANDARDS

and spare parts.
for each work material classication, indicates

recommended cutting conditions according
to the ISO categories for cutting grades, P, M
and K.
Order :
HSK-T TOOLS
H63TH-PCLNR/L-DX12
(4)
Dimensions
(mm) Mass
(lbs)
L1 F1
Stock
Stock
Insert Number
HSK-T TOOLS
Medium
Semi-Heavy
GH
MS
H000
(4)
Medium
Standard
95
Order Number
aTo
MA
(4)
Medium
MH
MS
H006
Medium
SA
(4)
Medium
Semi-Heavy
GH
95
Light
FH
(4)
Medium
Standard
MH
PCMN
Medium
SA
Please specify order number and hand of the tool (right/left).
HSK-T TOOLS
OUTLINE OF HSK-T TOOLS ..................................................................................... H002
CLASSIFICATION OF HSK-T TOOLS ................................................................. H004
STANDARD OF HSK-T TOOLS
EXTERNAL TURNING FACING
CNooINSERTS TOOL HOLDERS..................................................................................... H006
DNooINSERTS TOOL HOLDERS..................................................................................... H011
EXTERNAL TURNING FACING BORING
CNooINSERTS TOOL HOLDERS..................................................................................... H008
EXTERNAL TURNING COPYING
DNooINSERTS TOOL HOLDERS..................................................................................... H009
EXTERNAL TURNING FACING COPYING
RCooINSERTS TOOL HOLDERS..................................................................................... H012
FACING COPYING
VBooINSERTS TOOL HOLDERS..................................................................................... H013
GROOVING
MG INSERTS TOOL HOLDERS .......................................................................................... H014
THREADING
MMT INSERTS TOOL HOLDERS ....................................................................................... H016
MT INSERTS TOOL HOLDERS ........................................................................................... H017
EXTERNAL TURNING TOOL HOLDERS................................................... H019
BORING BAR HOLDERS...................................................................................... H021
BORING BAR SLEEVES ....................................................................................... H022
*Arranged
H100TH-Bpp-ppp
H022
H020
H019
H008
H021
H008
H006
H007
H011
H009
H010
H020
H021
H019
H100TH-EN3232R/L-130
H100TH-EV3232R/L-180
H63TH-ApppDCLNR/L12
H63TH-Bpp-pp
H63TH-DCLNL-L12-3
H63TH-DCLNR/L-DX12
H63TH-DCMNN-H/L12
H63TH-DDJNL-L15-3
H63TH-DDJNR/L-DX15
H63TH-DDNNN-H/L15
H63TH-EN2525R/L-115
H63TH-EV2020R/L-105-3
H63TH-EV2525R/L-112
H014
H016
H016
H017
H006
H007
H009
H010
H012
H012
H013
H013
H022
H63TH-MGHR/L-DX43pp
H63TH-MMTENR-H/L16
H63TH-MMTER-DX16
H63TH-MTHR/L-DX43
H63TH-PCLNR/L-DX12
H63TH-PCMNN-H/L12
H63TH-PDJNR/L-DX15
H63TH-PDNNN-H/L15
H63TH-PRDCN-H/L12
H63TH-PRGCR/L-DX12
H63TH-SVPBR/L-DX16
H63TH-SVVBN-H/L16
SL32pp-90
H001
Tooling system
for turning on
multi-task machines
HSK-T TOOLS
HSK-T System
(ICTM standard)
Highly accurate cutting

edge positioning
HSK-T is a new HSK system designed

for turning on multi-task machines that
are compatible with HSK-A type (ISO
standard: ISO12164-1:2001). It was
jointly developed by a consortium of
Japanese manufacturers and is now
used worldwide as the ICTM standard.
The new HSK system was published as
an ISO standard under the
denomination of HSK-T type in 2008.
(ISO12164-3:2008)
The HSK-T type has a closer tolerance

between the spindle key and tool holder
keyway than the HSK-A type. This
results in higher cutting edge positional
accuracies. For milling, the conventional
HSK-A type tools can be still used.
HSK-T TOOLS
Compatible with both multi-task machines and machining centers
HSK-A63 (ISO standard)

Rotating tool holder
HSK-T spindle
Multi-task machines
HSK-T
Turning tool holder
HSK-A spindle
Machining center
Improved keyway tolerance

Tolerance comparison (Example)
Close tolerance
(mm)
0.10
12.25 Key tolerance 12.35
Minimum clearance 0.15
HSK
A63
0.08
Keyway
tolerance
12.5
Maximum clearance 0.33
12.2
12.3
12.4
12.5
12.58
12.6
0.025
12.385
Spindle key
Holder keyway
HSK
T63
Achieves proper edge height.

Higher machining accuracy.
12.41
Minimum clearance 0.015

0.035
12.425
12.46
Maximum clearance 0.075
From ICTM-HSK to HSK-T

The order numbers of the tool holders will be changed according to the global standardization.
HSK-Aoo equivalent size
Conventional
order number
HooA
Revised
order number
HooTH
ICTM-HSK manual clamping with through coolant holes
WH
XXXX
HSK-Too size (ICTM-HSK standard)

Manual clamping with through coolant holes
H002
XXXX
Highly accurate and rigid HSK-T type tooling

system for use on multi-task machines.
Straight type tools suitable for use on multi-task machines
Work face
By tilting the machines B spindle

(main axis of the tool) at 45 deg.
interference between the spindle,
holder, workpiece and chuck can
be avoided.
Improve centerline height by positioning the

cutting edge at the center of the spindle.
No interference
Clearance
Avoid workpiece interference with improved

tool accessibility.
Increased stability and accuracy

can be achieved because the
cutting edge centerline height is
not affected by the gap between
the spindle and the key.
Drive key
Drive keyway
New single-action double clamp series

The double clamp mechanism offers high rigidity, accuracy,
reliability that ensures secure insert clamping. Therefore
Clamp bridge
making it suitable for turning of difcult to machine
Insert
materials such as stainless and heat resistant alloys.
Clamp screw
Spring
Handed type for

turning and facing
Straight type for

turning and facing
Shim pin
HSK-T TOOLS
Shim
For turning,
facing and boring
3 on 1 tool for process and tool consolidation

3 turning inserts of the same geometry can be installed on a single tool.
The same type of insert can
be installed for quick change
to back up tools.
Different types of inserts can be
installed for different applications
(rough and semi nishing and nishing)
Inserts in different grade types
can be installed to cover various
kinds of workpieces.
New HSK-T100 size for large workpieces

Larger tool holder sizes for high efciency machining.
Square shank holder type
Boring bar / Drill type
Sleeve
A single tool can be used with different sized tool holders.

Available for use with JIS B4126 (ISO 5610) 32x32 and 32x25 tools.
Possible to t a 25x25 tool by using a 7mm plate.
Possible to t a 1"x1" tool by using a 6.6mm plate.
Please
prepare a plate on your own.
*
25x25 size tool

7mm plate
H003
HSK-T TOOLS
CLASSIFICATION OF HSK-T TOOLS

EXTERNAL TURNING FACING COPYING
Order Number
Geometry
Order Number
H63TH-PCLNR/L-DX12
Geometry
H63TH-PCMNN-H/L12
95
^H006
^H007
H63TH-DCLNR/L-DX12
H63TH-DCMNN-H/L12
95
95
^H006
^H007
H63TH-PDJNR/L-DX15
H63TH-PDNNN-H/L15
107
30
93
^H009
^H010
H63TH-DDJNR/L-DX15
H63TH-DDNNN-H/L15
107
30
HSK-T TOOLS
93
^H009
^H010
H63TH-SVPBR/L-DX16
^H013
95
H63TH-SVVBN-H/L16
117
30
117
30
^H013
H63TH-PRGCR/L-DX12
H63TH-PRDCN-H/L12
^H012
^H012
H63TH-DCLNL-L12-3
EXTERNAL TURNING FACING BORING

^H008
95
H63TH-DDJNL-L15-3
Order Number
Geometry
H63TH-A25KDCLNR/L12
H63TH-A32LDCLNR/L12
93
^H011
H004
^H008
95
EXTERNAL TURNING TOOL HOLDERS

Order Number
Holder
H63TH-EV2525R/L-112
^H019
H100TH-EV3232R/L-180
^H019
H63TH-EN2525R/L-115
^H020
*1
HSK-T TOOLS
H100TH-EN3232R/L-130
^H020
*1
H63TH-EV2020R/L-105-3
^H021
THREADING
BORING BAR HOLDERS
Order Number
Geometry
H63TH-MMTER-DX16
Order Number
H63TH-Boo-oo
^H016
H63TH-MMTENR-H/L16
^H021
H100TH-Boo-ooo
^H016
H63TH-MTHR/L-DX43
Holder
^H022
SL32oo-90
(Sleeve)
^H017
*
*
*2
^H022
1 Mitsubishi Materials is licensed for production and distribution of these tools from MORI SEIKI Co., LTD. under Japan Patent No.3720202.
2 The SL32oo-90 sleeve is only for use with H100TH-B32-135.
H005
HSK-T TOOLS

PCLN
Finish
Light
FH
Medium
SA
MA
(4)
(4)
(4)
Medium
Medium
Medium
Semi-Heavy
Standard
MH
GH
95
(4)
(4)
Stainless
CBN
(4)
MS
Order Number
Stock
Insert Number
R L
H63TH-PCLNR/L-DX12
CNMo
s s CNGo
NP-CNoA
43o
(4)
(4)
Dimensions
(mm) Mass
(lbs)
L1 F1
Shim
Shim Pin
Clamp
Lever
Clamp
Screw
Wrench
65 45 2.9
LLSCN42
LLP14
LLCL14
LLCS108
HKY30R
HSK-T TOOLS
DCLN
External turning
Facing
DOUBLE CLAMP type
Finish
FH
Light
Medium
SA
MA
(4)
(4)
(4)
Medium
Medium
Medium
Semi-Heavy
Standard
MH
GH
95
(4)
(4)
Stainless
CBN
(4)
MS
Order Number
Stock
Insert Number
R L
H63TH-DCLNR/L-DX12
CNMo
s s CNGo
NP-CNoA
43o
(4)
(4)
Dimensions
(mm) Mass
(lbs)
L1 F1
Shim
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
65 45 2.9
LLSCN42
LLP14
DCK2613
DCS1
DC0621T
TKY20F

Work Material
Hardness
Cutting Mode
Finish Cutting
Light Cutting
Medium Cutting
Finish Cutting
Carbon Steel
180HB 350HB
Light Cutting
Alloy Steel
Medium Cutting
Finish Cutting
M
< 200HB
Light Cutting
Stainless Steel
Medium Cutting
Light Cutting
K
Tensile Strength
Gray Cast Iron
Medium Cutting
< 350MPa
Semi-Heavy Cutting
Mild Steel
H006
< 180HB
Breaker
Grade
Cutting Speed (SFM)
FY
SY
MS
FH
SA
MA
FH
SA
MS
MA
Standard
Flat Top
NX3035
NX3035
UE6110
NX3035
UE6110
UE6110
US735
US735
US735
UC5115
UC5115
UC5115
850 1210
770 1100
850 1440
655 935
685 1160
620 1065
345 655
310 605
275 540
520 965
520 965
505 915
PCLN type inserts
A068A073
DCLN type inserts
A068A073
CBN & PCD inserts
B022B024, B054
PCMN
Finish
Light
FH
Medium
SA
MA
(4)
(4)
(4)
Medium
Medium
Medium
Semi-Heavy
Standard
MH
GH
95
(4)
(4)
Stainless
CBN
(4)
MS
Order Number
H63TH-PCMNN-H12
-L12
Stock
(4)
Insert Number
CNMo
CNGo
NP-CNoA
s
s
43o
Dimensions
(mm) Mass
(lbs)
L1
100
140
(4)
*
Shim
3.7 LLSCN42
6.0 LLSCN42
Shim Pin
Clamp
Lever
LLP14
LLP14
LLCL14
LLCL14
Clamp
Screw
Plug
LLCS108 HGM-PT1/8
LLCS108 HGM-PT1/8
Wrench
HKY30R
HKY30R

External turning
Facing
DOUBLE CLAMP type
Finish
FH
Light
Medium
SA
MA
(4)
(4)
(4)
Medium
Medium
Medium
Semi-Heavy
Standard
MH
GH
95
(4)
(4)
Stainless
CBN
(4)
HSK-T TOOLS
DCMN
MS
Order Number
H63TH-DCMNN-H12
-L12
Stock
(4)
s
s
Insert Number
CNMo
CNGo
NP-CNoA
43o
Dimensions
(mm) Mass
(lbs)
L1
100
140
(4)
*
Shim
3.7 LLSCN42
6.0 LLSCN42
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
LLP14
LLP14
DCK2613
DCK2613
DCS1
DCS1
DC0621T
DC0621T
TKY20F
TKY20F

Work Material
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180HB 350HB
Stainless Steel
< 200HB
Gray Cast Iron
Tensile Strength
< 350MPa
Cutting Mode
Breaker
Grade
Cutting Speed (SFM)
Finish Cutting
Light Cutting
Medium Cutting
Finish Cutting
Light Cutting
Medium Cutting
Finish Cutting
Light Cutting
Medium Cutting
Light Cutting
Medium Cutting
Semi-Heavy Cutting
FY
SY
MS
FH
SA
MA
FH
SA
MS
MA
Standard
Flat Top
NX3035
NX3035
UE6110
NX3035
UE6110
UE6110
US735
US735
US735
UC5115
UC5115
UC5115
850 1210
770 1100
850 1440
655 935
685 1160
620 1065
345 655
310 605
275 540
520 965
520 965
505 915
PCMN type inserts
A068A073
DCMN type inserts
A068A073
SPARE PARTS
P001
CBN & PCD inserts
B022B024, B054
TECHNICAL DATA
Q001
H007
HSK-T TOOLS

DCLN
External turning
Facing
DOUBLE CLAMP type
Finish
FH
Light
Medium
SA
MA
(4)
(4)
(4)
Medium
Medium
Medium
Semi-Heavy
Standard
MH
GH
95
(4)
(4)
Stainless
CBN
(4)
MS
Order Number
Stock
Insert Number
H63TH-DCLNL-L12-3
CNMo
CNGo
NP-CNoA
43o
Dimensions
(mm) Mass
(lbs)
L1 F1
(4)
(4)
*
Shim
140 30 4.9 LLSCN42
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
LLP14
DCK2613
DCS1
DC0621T
TKY20F
DCLN
External turning
Facing Boring
DOUBLE CLAMP type
Finish
FH
Medium
MA
(4)
(4)
(4)
Medium
Medium
Medium
Semi-Heavy
Standard
MH
HSK-T TOOLS
Light
SA
GH
95
(4)
(4)
Stainless
CBN
(4)
MS
R L
H63TH-A25KDCLNR/L12
-A32LDCLNR/L12
Dimensions
(mm)
Insert Number
L1
s s CNMo
CNGo
s s NP-CNoA
43o
L2
L3
(4)
Min. Cutting
Diameter
Order Number
Stock
D1
F1 RR (mm)
125 82 84 17
140 100 102 22
11
13
(4)
Mass
(lbs)
Shim
Shim
Pin
Clamp
Bridge
Spring Clamp
Screw Wrench
32 2.4 LLSCP42 LLP14 DCK2613 DCS1 DC0621T TKY20F

40 3.9 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F

Work Material
Hardness
Cutting Mode
Breaker
FY
Finish Cutting
SY
Light Cutting
MS
Medium Cutting
FH
Finish Cutting
Carbon Steel
180HB 350HB
SA
Light
Cutting
Alloy Steel
MA
Medium Cutting
FH
Finish
Cutting
M
< 200HB
SA
Light Cutting
Stainless Steel
MS
Medium Cutting
MA
Light Cutting
K
Tensile Strength
Standard
Gray Cast Iron
Medium Cutting
< 350MPa
Flat Top
Semi-Heavy Cutting
H008
Mild Steel
< 180HB
Grade
Cutting Speed (SFM)
NX3035
NX3035
UE6110
NX3035
UE6110
UE6110
US735
US735
US735
UC5115
UC5115
UC5115
850 1210
770 1100
850 1440
655 935
685 1160
620 1065
345 655
310 605
275 540
520 965
520 965
505 915
DCLN type inserts
A068A073
CBN & PCD inserts
B022B024, B054
PDJN
Finish
External turning Copying
FH
Medium
MA
(4)
(4)
(4)
Medium
Medium
Semi-Heavy
Stainless
GH
MH
93
Light
SA
MS
(4)
(4)
G Class
CBN
(4)
R/L
Order Number
Stock
Insert Number
R L
H63TH-PDJNR/L-DX15
43o
(4)
*1
Dimensions
(mm) Mass
(lbs)
L1 F1
Shim
Shim Pin
65 45 2.6
LLSDN43
(LLSDN42)
LLP14
Clamp Lever Clamp Screw

LLCL24
LLCS108
Wrench
HKY30R
1 Clamp Torque (lbf-in) : LLCS108=29

2 Please use shim no. LLSDN42 with .25inch thick inserts. When using .25inch thick inserts, the shim should be ordered separately.
DDJN
External turning
Copying
DOUBLE CLAMP type
Finish
FH
Medium
MA
(4)
(4)
(4)
Medium
Medium
Semi-Heavy
Stainless
GH
MH
93
Light
SA
MS
(4)
(4)
G Class
CBN
(4)
HSK-T TOOLS
*
*
s s
DNMo
DNGo
NP-DNoA
(4)
*2
R/L
Order Number
Stock
Insert Number
R L
H63TH-DDJNR/L-DX15
*
*
s s
DNMo
DNGo
NP-DNoA
43o
(4)
(4)
*2
*1
Dimensions
(mm) Mass
(lbs)
L1 F1
Shim
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
65 45 2.6
LLSDN43
(LLSDN42)
LLP24
DCK2613
DCS1
DC0621T
TKY20F
1 Clamp Torque (lbf-in) : DC0621T=44


Work Material
M
K
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180HB 350HB
Stainless Steel
< 200HB
Gray Cast Iron
Tensile Strength
< 350MPa
Cutting Mode
Breaker
Grade
Cutting Speed (SFM)
Finish Cutting
Light Cutting
Medium Cutting
Finish Cutting
Light Cutting
Medium Cutting
Finish Cutting
Light Cutting
Medium Cutting
Light Cutting
Medium Cutting
Semi-Heavy Cutting
FY
SY
MS
FH
SA
MA
FH
SA
MS
MA
Standard
Flat Top
NX3035
NX3035
UE6110
NX3035
UE6110
UE6110
US735
US735
US735
UC5115
UC5115
UC5115
850 1210
770 1100
850 1440
655 935
685 1160
620 1065
345 655
310 605
275 540
520 965
520 965
505 915
PDJN type inserts
A074A078
DDJN type inserts
A074A078
SPARE PARTS
P001
CBN & PCD inserts
B025B027, B054
TECHNICAL DATA
Q001
H009
HSK-T TOOLS

PDNN
Finish
External turning Copying
FH
Medium
MA
(4)
(4)
(4)
Medium
Medium
Semi-Heavy
Stainless
MH
107
30
Light
SA
MS
GH
(4)
(4)
G Class
CBN
(4)
R/L
Order Number
H63TH-PDNNN-H15
-L15
*
*
Stock
(4)
s
s
Insert Number
DNMo
DNGo
NP-DNoA
100
140
3.5
5.5
Shim
Shim Pin
Clamp
Lever
LLSDN43
LLP14
LLP14
LLCL24
LLCL24
(LLSDN42)
LLSDN43
(LLSDN42)
Clamp
Screw
Plug
LLCS108 HGM-PT1/8
LLCS108 HGM-PT1/8
Wrench
HKY30R
HKY30R
1 Clamp Torque (lbf-in) : LLCS108=29

DDNN
HSK-T TOOLS
43o
Dimensions
(mm) Mass
(lbs)
L1
(4)
*1
*2
External turning
Copying
DOUBLE CLAMP type
Finish
Medium
MA
(4)
(4)
(4)
Medium
Medium
Semi-Heavy
Stainless
MH
107
30
Light
SA
FH
MS
GH
(4)
(4)
G Class
CBN
(4)
R/L
Order Number
H63TH-DDNNN-H15
-L15
Stock
(4)
s
s
Insert Number
DNMo
DNGo
NP-DNoA
43o
Dimensions
(mm) Mass
(lbs)
L1
100
140
3.5
5.5
(4)
*1
Shim
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
LLSDN43
LLP24
LLP24
DCK2613
DCK2613
DCS1
DCS1
DC0621T
DC0621T
TKY20F
TKY20F
(LLSDN42)
LLSDN43
(LLSDN42)
Torque (lbf-in) : DC0621T=44

*12 Clamp
Please use shim no. LLSDN42 with .25inch thick inserts. When using .25inch thick inserts, the shim should be ordered separately.
*

Work Material
Hardness
Cutting Mode
Finish Cutting
P
Light Cutting
< 180HB
Mild Steel
Medium Cutting
Finish Cutting
Carbon Steel
180HB 350HB
Light Cutting
Alloy Steel
Medium Cutting
Finish Cutting
M
Light Cutting
< 200HB
Stainless Steel
Medium Cutting
Light Cutting
K
Tensile Strength
Medium Cutting
Gray Cast Iron
< 350MPa
Semi-Heavy Cutting
H010
Breaker
Grade
Cutting Speed (SFM)
FY
SY
MS
FH
SA
MA
FH
SA
MS
MA
Standard
Flat Top
NX3035
NX3035
UE6110
NX3035
UE6110
UE6110
US735
US735
US735
UC5115
UC5115
UC5115
850 1210
770 1100
850 1440
655 935
685 1160
620 1065
345 655
310 605
275 540
520 965
520 965
505 915
PDNN type inserts
A074A078
DDNN type inserts
A074A078
CBN & PCD inserts
B025B027, B054
DDJN
DOUBLE CLAMP type
Finish
(4)
(4)
Medium
Medium
MH
MA
93
(4)
(4)
Medium
Semi-Heavy
Stainless
MS
GH
Order Number
Stock
Insert Number
H63TH-DDJNL-L15-3
DNMo
DNGo
NP-DNoA
43o
Dimensions
(mm) Mass
(lbs)
L1 F1
Light
SA
FH
(4)
(4)
*1
*2
Shim
140 30 4.9 (LLSDN43

LLSDN42)
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
LLP24
DCK2613
DCS1
DC0621T
TKY20F
HSK-T TOOLS
Torque (lbf-in) : DC0621T=44

*12 Clamp
Please use shim no. LLSDN42 with .25inch thick inserts. When using .25inch thick inserts, the shim should be ordered separately.
*

Work Material
Hardness
P
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180HB 350HB
Stainless Steel
< 200HB
Gray Cast Iron
Tensile Strength
< 350MPa
Cutting Mode
Breaker
Grade
Cutting Speed (SFM)
Finish Cutting
Light Cutting
Medium Cutting
Finish Cutting
Light Cutting
Medium Cutting
Finish Cutting
Light Cutting
Medium Cutting
Light Cutting
Medium Cutting
Semi-Heavy Cutting
FY
SY
NX3035
NX3035
850 1210
770 1100
850 1440
655 935
685 1160
620 1065
345 655
310 605
275 540
520 965
520 965
505 915
MS
UE6110
FH
NX3035
SA
MA
UE6110
UE6110
FH
SA
MS
US735
US735
US735
MA
Standard
Flat Top
UC5115
UC5115
UC5115
DDJN type inserts
A074A078
SPARE PARTS
P001
CBN & PCD inserts
B025B027, B054
TECHNICAL DATA
Q001
H011
HSK-T TOOLS

PRGC
Medium
External turning Facing Copying
(12)
Order Number
Stock
Insert Number
R L
H63TH-PRGCR/L-DX12
s s
RCMX
Dimensions
(mm) Mass
(lbs)
L1 F1
1204M0 65 45 2.6
*
Shim
Shim Pin
LLSRN123
LLP13
Clamp Lever Clamp Screw

LLCL112
LLCS106
Wrench
HKY25R
PRDC
Medium
External turning Facing Copying
(12)
Order Number
Stock
HSK-T TOOLS
H63TH-PRDCN-H12
-L12
Insert Number
RCMX
1204M0
Dimensions
(mm) Mass
(lbs)
L1 B2
*
Shim Pin
Clamp
Lever
100 69 3.1 LLSRN123
LLP13
LLCL112
LLCS106 HGM-PT1/8
HKY25R
140 75 5.1 LLSRN123
LLP13
LLCL112
LLCS106 HGM-PT1/8
HKY25R
Shim
Clamp
Screw
Plug
Wrench

Work Material
Hardness
Cutting Mode
Breaker
Medium Cutting
Mild Steel
Standard
< 180HB
P
Medium Cutting
Standard
180HB 350HB
Medium Cutting
Standard
Stainless Steel
M
< 200HB
H012
Grade
Cutting Speed (SFM)
UE6110
UE6110
670 1150
490 850
US735
230 425
PRGC type inserts
A115
PRDC type inserts
A115
SVPB
Finish
Facing Copying
R/L-F
(3)
(3)
Medium
Medium
MV
117
30
Light
SV
Standard
(3)
(3)
CBN
Order Number
Stock
Insert Number
R L
H63TH-SVPBR/L-DX16
VBMT
VBGT
s s
33o
(3)
Dimensions
(mm) Mass
(lbs)
L1 F1
Shim
Shim Pin
Clamp Screw
Wrench
65 45 2.4
SPSVN32
BCP141
TS35D
TKY15F
* Clamp Torque (lbf-in) : TS35D=31

Finish
Facing Copying
R/L-F
(3)
(3)
Medium
Medium
MV
117
30
Light
SV
Standard
(3)
HSK-T TOOLS
SVVB
(3)
CBN
Order Number
Stock
(3)
H63TH-SVVBN-H16
-L16
Insert Number
VBMT
VBGT
33o
Dimensions
Mass
(mm)
(lbs)
B2
L1
Shim
Shim Pin
Clamp Screw
Plug
Wrench
100 6630' 2.9
SPSVN32
BCP141
TS35D
HGM-PT1/8
TKY15F
140 7230' 4.9
SPSVN32
BCP141
TS35D
HGM-PT1/8
TKY15F
* Clamp Torque (lbf-in) : TS35D=31

Work Material
M
K
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180HB 350HB
Stainless Steel
Gray Cast Iron
< 200HB
Cutting Mode
Breaker
Grade
Cutting Speed (SFM)
Finish Cutting
Medium Cutting
Finish Cutting
Medium Cutting
Medium Cutting
Medium Cutting
F
MV
F
MV
MV
MV
AP25N
UE6020
AP25N
UE6020
US735
UE6020
820 (490 985)

655 (490 820)
690 (490 850)
555 (390 690)
330 (230 390)
555 (460 655)
SVPB type inserts
A125, A126
SVVB type inserts
A125, A126
SPARE PARTS
P001
CBN & PCD inserts
B047
TECHNICAL DATA
Q001
H013
HSK-T TOOLS

MG
Grooving
Stock
Order Number
Insert Number
R L
H63TH-MGHR/L-DX4315
s s
43125
MGTR/L
-DX4323
s s
-DX4333
s s
43470
Max.
Groove Width Groove Dimensions
Depth (mm) Mass
(lbs)
ap
W3
(mm) L1 F1
(mm)
1.25
1.2
1.45
1.5
1.5< W3< 2.3
2.3 < W3< 3.3
4.5
3.3 < W3< 4.7
4.5
*
Clamp
Bridge
Clamp
Screw
65 45 2.6 MTK1R/L HBH06020
Spring
Wrench
MES3
HKY40R
HSK-T TOOLS
* Clamp Torque (lbf-in) : HBH06020=62

Work Material
H014
Hardness
Grade
Cutting Speed (SFM)
Feed (IPR)
VP20MF
390 (330 460)
.0039 (.0012 .0071)
NX2525
425 (330 525)
.0047 (.0012 .0079)
Carbon Steel
Alloy Steel
180 350HB
Stainless Steel
< 200HB
VP20MF
390 (330 460)
.0039 (.0012 .0071)
Gray Cast Iron
VP20MF
390 (330 460)
.0039 (.0012 .0071)
s : Inventory maintained in Japan. (10 inserts in one case) (1 insert in one case for CBN)
r
INSERTS FOR MG TYPE

MB8025
UTi20T
NX2525
Dimensions (mm)
Groove
Width
L3
D1
S1
Re
1.2
12.7
4.76
0.2
W3
R L R L R L R L
(mm)
s s s r s s s s
1.25
1.45
1.5
12.7
4.76
0.2
1.5
12.7
4.76
0.2
1.75
12.7
4.76
0.2
12.7
4.76
0.2
2.3
12.7
4.76
0.2
2.5
4.5
12.7
4.76
0.3
43145
s r r r s
43150
s s s s s s s s
43175
s s s r s
43200
s s s s s s s s
43230
s s s s s s s s
43250
s s s s s s s s
43260
s r r
s s
2.6
4.5
12.7
4.76
0.3
43270
s r
s r
2.7
4.5
12.7
4.76
0.3
43280
s s s r s s s s
2.8
4.5
12.7
4.76
0.3
43300
s s s s s s s s
4.5
12.7
4.76
0.3
43320
s s r
3.2
4.5
12.7
4.76
0.3
43330
s s s r s s s s
3.3
4.5
12.7
4.76
0.3
43350
s r s r s s s r
3.5
4.5
12.7
4.76
0.3
43400
s s s
s s s s
4.5
12.7
4.76
0.3
43420
s r r
s r
4.2
4.5
12.7
4.76
0.4
43430
s r r
s s s s
4.3
4.5
12.7
4.76
0.4
43450
s s s s s s s s
4.5
4.5
12.7
4.76
0.4
43470
s r r r
4.7
4.5
12.7
4.76
0.4
s r
s s
s s s s
s r
Geometry
(mm)
MGTR/L...
CBN Insert
SPARE PARTS
P001
TECHNICAL DATA
Q001
HSK-T TOOLS
MGTR/L43125
VP20MF
Order Number
NX55
Stock
Cermet Carbide CBN
Coated
H015
HSK-T TOOLS

MMTE
Threading
Order Number
Stock
Insert Number
H63TH-MMTER-DX16
Dimensions
(mm) Mass
(lbs)
L1 F1
MMT16ER ooooo 65 45 2.6
*
Clamp
Bridge
Clamp
Screw
Stop Ring
SETK51
SETS51
CR4
Shim
Screw
Shim
CTE32TP15 HFC03008
Wrench
zTKY15F
xHKY20R
* Clamp Torque (lbf-in) : SETS51=31, HFC03008=13
HSK-T TOOLS
MMTEN
Threading
*1
Stock
Tool holder for right hand insert only.
Order Number
H63TH-MMTENR-H16
Insert Number
Dimensions
(mm) Mass
(lbs)
L1
*
Clamp
Bridge
Clamp
Screw
*2
Stop Ring
Shim
Shim
Screw
Plug
Wrench
100
3.7 SETK51 SETS51
CR4
CTE32TP15 HFC03008 HGM-PT1/8
zTKY15F
xHKY20R
140
6.0 SETK51 SETS51
CR4
CTE32TP15 HFC03008 HGM-PT1/8
zTKY15F
xHKY20R
MMT16ER ooooo
-L16
use with B axis tilted at 45 degrees.

*12 For
Clamp Torque (lbf-in) : SETS51=31, HFC03008=13
*

Work Material
H016
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180 350HB
Stainless Steel
< 200HB
Gray Cast Iron
Grade
Cutting Speed (SFM)
VP10MF
VP15TF
VP10MF
VP15TF
VP10MF
VP15TF
VP10MF
VP15TF
490 (230 755)

330 (195 460)
460 (260 655)
330 (195 460)
425 (260 590)
260 (130 390)
460 (260 655)
295 (195 390)
MMT type inserts
G014, G016, G020
MT
Threading
Order Number
Stock
Insert Number
R L
H63TH-MTHR/L-DX43
s s
MTTR/L
Dimensions
Mass
(mm)
(lbs)
Clamp Bridge
L1
F1
43oooo
65
45
2.6
MTK1R/L
*
Clamp Screw
Spring
Wrench
HBH06020
MES3
HKY40R
HSK-T TOOLS
* Clamp Torque (lbf-in) : HBH06020=62

Work Material
Hardness
P
Mild Steel
Carbon Steel
Alloy Steel
< 180HB
180HB 350HB
M
Stainless Steel
Cutting Speed (SFM)
UP20M
460 (330 590)
NX55
655 (490 820)
UTi20T
390 (330 490)
UP20M
390 (330 490)
NX55
555 (490 655)
UTi20T
330 (230 390)
UP20M
390 (260 490)
UTi20T
330 (230 425)
UP20M
260 (195 330)
UTi20T
260 (195 330)
HTi10
330 (230 425)
< 200HB
K
Gray Cast Iron
Grade
MT type inserts
H018
SPARE PARTS
P001
TECHNICAL DATA
Q001
H017
HSK-T TOOLS

INSERTS FOR MT TYPE
NX55
UTi20T
HTi10
MTTR436000
L436000
R436001
L436001
R436002
L436002
R436003
L436003
R436004
L436004
MTTR435501
L435501
R435502
L435502
R435503
L435503
Class
Order Number
Dimensions (mm)
Pitch
UP20M
Partial Prole 55
Partial Prole 60
Type
Coated Cermet Carbide
mm
G
G
0.8
1.0 1.75
12.7
4.76
0.1
1.0 1.75
12.7
4.76
0.1
2.0 2.5
12.7
4.76
0.2
2.0 2.5
12.7
4.76
0.2
3.0 3.5
12.7
4.76
0.3
3.0 3.5
12.7
4.76
0.3
G
G
4.0 4.5
4.0 4.5
12.7
12.7
4.76
4.76
0.4
0.4
G
G
28 10
28 10
12.7
12.7
4.76
4.76
0.1
0.1
16 8
12.7
4.76
0.2
16 8
12.7
4.76
0.2
11 8
12.7
4.76
0.3
11 8
12.7
4.76
0.3
D1
S1
12.7
12.7
4.76
4.76
Geometry
Re
thread/inch
0.8
MTTR/L(60) Partial prole
0
0
MTTR/L(55) Partial prole
y STANDARD OF DEPTH OF CUT a Metric Screw Thread
The chart on the right shows the cutting

depths when machining external ISO
metric screw threads.
a When using cermet grades or cutting
stainless steel, please increase the
number of passes by 2 or 3 extra
passes.
a
P (Pitch)
h1
h2
r (Corner Radius)
Number of Passes
HSK-T TOOLS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
0.75
0.46
0.35
0.11
0.18
0.13
0.10
0.05
1.00
0.61
0.47
0.14
0.20
0.15
0.10
0.10
0.06
1.25
0.77
0.59
0.18
0.20
0.18
0.12
0.12
0.10
0.05
Unit : mm
1.50
0.92
0.70
0.22
0.25
0.20
0.15
0.15
0.10
0.07
1.75
1.07
0.82
0.25
0.25
0.20
0.20
0.15
0.12
0.10
0.05
2.00
1.23
0.94
0.29
0.25
0.25
0.20
0.15
0.15
0.10
0.08
0.05
2.50
1.53
1.17
0.36
0.30
0.25
0.20
0.20
0.15
0.10
0.10
0.10
0.08
0.05
3.00
1.84
1.41
0.43
0.30
0.25
0.25
0.20
0.20
0.15
0.15
0.10
0.10
0.09
0.05
3.50
2.15
1.65
0.50
0.35
0.30
0.25
0.20
0.20
0.20
0.15
0.15
0.10
0.10
0.10
0.05
(Note) The rst pass causes a high load on the cutting edge.
In order to avoid damage, keep the depth of cut to 0.4 0.5mm maximum.
H018
s : Inventory maintained in Japan. (10 inserts in one case) r : Non stock, produced to order only.
4.00
2.45
1.87
0.58
0.35
0.30
0.25
0.25
0.25
0.20
0.20
0.15
0.15
0.10
0.10
0.10
0.05
4.50
2.76
2.11
0.65
0.40
0.35
0.30
0.25
0.25
0.20
0.20
0.15
0.15
0.15
0.10
0.10
0.10
0.06
y This holder is for 2525 size tools.
Please shorten the tool as shown below

before use.
Cut
H63TH-EV2525R/L-112
Stock
R
Dimensions (mm)
L
L1
150 112
Mass
(lbs)
L2
h1
h2
F1
S1
b1
b2
77
25
32
53
45
13
38
32
Clamp Screw
Plug
HSS12025
HGM-PT1/8
8.6
HSK-T TOOLS
Order Number
y This holder is for 3232 and
32 x 25 size tools.
Order Number
H100TH-EV3232R/L-180
Stock
R
Dimensions (mm)
L
L1
L2
Mass
(lbs)
h1
h2
F1
S1
b1
b2
220 180 130 32
40
68
57
17
46
43 25.8
Clamp Screw
Nozzle Plug
Plug
HSS14035
SNA4
HSS06006
(Note) Possible to t a 25 x 25 tool by using a 7mm plate.

Possible to t a 1" x 1" tool by using a 6.6mm plate.
SPARE PARTS
P001
TECHNICAL DATA
Q001
H019
HSK-T TOOLS

Please shorten the tool as shown below before use.

Cut
Mitsubishi Materials is licensed for production and

distribution of these tools from MORI SEIKI Co., LTD.
under Japan Patent No.3720202.
Order Number
HSK-T TOOLS
H63TH-EN2525R/L-115
Stock
Dimensions (mm)
Mass
(lbs)
L1
L2
h1
h2
b1
b2
115
40
110
25
32
53
45
45
8.2
Clamp Screw
Nozzle Plug
Plug
HSS12030
SNA4
HSS06006
y This holder is for 3232 and 32 x 25 size tools.
Please shorten the tool as shown below before use.
Cut
Mitsubishi Materials is licensed for production and

distribution of these tools from MORI SEIKI Co., LTD.
under Japan Patent No.3720202.
Order Number
H100TH-EN3232R/L-130
Stock
Dimensions (mm)
L1
L2
h1
h2
b1
b2
130
40
110
32
32
68
47
43 14.6
(Note) Possible to t a 25 x 25 tool by using a 7mm plate.

Possible to t a 1" x 1" tool by using a 6.6mm plate.
H020
Mass
(lbs)
Clamp Screw
Nozzle Plug
Plug
HSS14030
SNA4
HSS06006
Please shorten the tool as shown below

before use.
Cut
H63TH-EV2020R/L-105-3
Stock
R
Dimensions (mm)
L
L1
140 105
L2
D8
F1
S1
b1
70
20
90
40
15
35
BORING BAR HOLDERS
Order Number
Mass
(lbs)
6.4
Clamp Screw
Nozzle Plug
Plug
HSS12030
HSS05012
HSS06006
Internal turning
HSK-T TOOLS
Order Number
Dimensions (mm)
Stock
Mass
(lbs)
D5
D8
L1
L2
Clamp Screw
H63TH-B08-65
28
65
40
M8
2.0
HSS08010
-B10-70
35
10
70
45
M8
2.2
HSS08012
-B12-70
42
12
70
45
M8
2.4
HSS08012
-B16-75
48
16
75
50
M10
2.9
HSS10016
-B20-75
52
20
75
50
M10
3.1
HSS10016
-B25-83
62
25
83
58
M12
3.7
HSS12016
-B32-87
62
32
87
62
M12
3.7
HSS12016
-B40-97
65
40
97
72
M16
4.0
HSS16012
SPARE PARTS
P001
TECHNICAL DATA
Q001
(Note) Please cut the boring bar to adjust the shank length, this also applies to indexable type drills.
H021
HSK-T TOOLS

BORING BAR HOLDERS
Order Number
Internal turning
Dimensions (mm)
Stock
Mass
(lbs)
D5
D8
L1
L2
Clamp Screw
H100TH-B25-120
62
25
120
88
12
8.6
HSS12016
-B32-135
72
32
135
102
12
10.6
HSS12018
-B40-150
82
40
150
117
16
13.0
HSS16020
-B50-180
92
50
180
147
16
17.0
HSS16020
HSK-T TOOLS
(Note) Please cut the boring bar to adjust the shank length, this also applies to indexable type drills.
BORING BAR SLEEVES FOR H100TH-B32-135
Order Number
Dimensions (mm)
Stock
Mass
(lbs)
D1
L1
Clamp Screw
SL3208-90
32
95
1.3
HSS06008
3210-90
10
32
95
1.1
HSS08008
3212-90
12
32
95
1.1
HSS08008
3216-90
16
32
95
1.1
HSS08006
3220-90
20
32
95
0.9
HSS08005
(Note) These sleeves are only compatible with H100TH-B32-135 holder.
H022
SPARE PARTS
P001
TECHNICAL DATA
Q001
Memo
H023
GUIDE TO SOLID CARBIDE END MILLS

aSection
organization
zOrganized according to cutting mode for milling. (Refer to END MILL LIST.)
PHOTO OF PRODUCT
PRODUCT TITLE
ITEM NUMBER
PRODUCT BLOCK
DIAMOND STAR END MILLS
DS2SS
Short, 2 ute
Carbon Steel, Alloy Steel, Cast Iron Tool Steel, Pre-Hardened Steel, Hardened Steel
(<30HRC)
( < 45HRC)
CARBIDE
D1 < .0156"
.0312" < D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.001"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
Type 1
SQUARE
GEOMETRY
Type 2
HRC
<55
UWC
a 2 ute square end mill for general purpose.

a Helix angle 30.
BALL
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
.0156
.0312
.0469
.0625
.0781
.0938
.1094
.1250
.1406
.1562
.1719
.1875
.2031
.2187
.2344
.2500
.2813
.3125
.3750
.4375
.5000
.6250
.7500
.023
.063
.094
.125
.156
.188
.219
.250
.313
.313
.375
.375
.500
.500
.500
.500
.500
.500
.563
.625
.625
.750
1.000
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.500
2.500
3.000
3.000
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.188
.188
.250
.250
.250
.250
.313
.313
.375
.438
.500
.625
.750
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
TAPER
RADIUS
DS2SSD1/64
D1/32
D3/64
D1/16
D5/64
D3/32
D7/64
D1/8
D9/64
D5/32
D11/64
D3/16
D13/64
D7/32
D15/64
D1/4
D9/32
D5/16
D3/8
D7/16
D1/2
D5/8
D3/4
SOLID END MILLS
I014
PRODUCT FEATURES
Unit : Inch
Dia.
a
a
a
r
a
r
a
r
r
r
a
r
r
r
a
r
r
a
r
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
2
2
2
2
2
I192
PAGE REFERENCE
CUTTING CONDITIONS

PRODUCT STANDARDS
indicates diameters, order numbers,
stock status, dimensions,
and for the title product.
aTo
I000
Order:
Please specify order number.
MILLING
SOLID CARBIDE END MILLS

PRODUCT CODE CORRESPONDENCES ............................ I002
SYMBOL DESCRIPTIONS ..................................................... I003
END MILLS SELECTION CHART .......................................... I004
SOLID ENDMILL STANDARD
DIAMOND STAR END MILLS (DS Type) ...........................
MSTAR END MILLS (MS Type) ..........................................
MIRACLE END MILLS (VC Type).......................................
IMPACT MIRACLE END MILLS (VF Type) ........................
DIAMOND COATED END MILLS (DF Type) ......................
CBN END MILLS .................................................................
UNCOATED CARBIDE END MILLS ...................................
I014
I050
I112
I138
I178
I186
I188
CUTTING CONDITONS ........................................................... I192

*I190
C2MHA
I188
I189
I191
I186
I187
I180
I181
I183
I178
I179
I184
I023
I016
I032
I015
I022
I031
I035
I036
I014
I018
I039
I043
I027
I048
I037
I045
I024
I017
I038
I042
I044
I026
I021
I030
I020
I029
I034
I025
I019
I033
I041
I040
I047
I046
C2SA
C3SA
C3SARB
CBN2XLB
CBN2XLRB
DF2MB
DF2XLB
DF3XB
DF4JC
DF4XL
DFPSRB
DS2LB (INCH)
DS2LS (INCH)
DS2MRB (INCH)
DS2MS (INCH)
DS2SB (INCH)
DS2SRB (INCH)
DS2SRB_A (INCH)
DS2SRB_NA (INCH)
DS2SS (INCH)
DS3MC (INCH)
DS3MH_SS (INCH)
DS3MHB_SS (INCH)
DS3MHH60 (INCH)
DS3MHHRB (INCH)
DS3MHR_A (INCH)
DS3MHRB_SS (INCH)
DS3SB (INCH)
DS3SC (INCH)
DS3SH_SS (INCH)
DS3SHB_SS (INCH)
DS3SHRB_SS (INCH)
DS4LB (INCH)
DS4LC (INCH)
DS4LC_CB (INCH)
DS4MC (INCH)
DS4MC_CB (INCH)
DS4MRB (INCH)
DS4SB (INCH)
DS4SC (INCH)
DS4SRB (INCH)
DS5LH_SS (INCH)
DS5MH_SS (INCH)
DS5MHRB_SS (INCH)
DS5SHRB_SS (INCH)
I028
I049
I075
I075
I054
I055
I079
I053
I090
I051
I097
I107
I078
I050
I087
I056
I061
I059
I080
I085
I092
I076
I077
I070
I101
I108
I069
I093
I068
I071
I074
I086
I065
I063
I095
I066
I067
I062
I137
I118
I119
I120
I123
I129
I124
I135
DS6MHH60 (INCH)
DS6MHHRB (INCH)
MS2ES(35)
MS2ES(45)
MS2JS
MS2LS
MS2MB
MS2MD
MS2MRB
MS2MS
MS2MT
MS2MTB
MS2SB
MS2SS
MS2XB
MS2XL
MS2XL (INCH)
MS2XL6
MS2XLB
MS2XLB (INCH)
MS2XLRB
MS3ES
MS4EC
MS4JC
MS4LT
MS4LTB
MS4MC
MS4MRB
MS4SC
MS4XL
MS4XL (INCH)
MS4XLB (INCH)
MSJHD
MSMHD
MSMHDRB
MSMHZD
MSMHZD (INCH)
MSSHD
VC2C
VC2ESB
VC2PSB
VC2PSBP
VC3MB
VC4JRB
VC4MB
VC4STB
I115
I116
I130
I132
I131
I113
I112
I114
I133
I125
I128
I117
I121
I140
I156
I157
I158
I155
I154
I138
I160
I159
I165
I168
I141
I169
I145
I146
I175
I176
I152
I147
I177
I170
I172
I144
I149
I153
I142
I143
I173
I174
I148
I150
I151
VC6MH
VC8MH
VCHFRB
VCHFRB (INCH)
VCHFRB(TAPER NECK)
VCLD
VCMDSC
VCMH
VCMHDRB
VCPSRB
VCPSRB(TAPER NECK)
VCSFPR
VCXB
VF2MV
VF2SB
VF2SDB
VF2SDBL
VF2SSB
VF2WB
VF2XL
VF2XLB
VF2XLBS
VF3XB
VF4MB
VF4MV
VF4SVB
VF6MHV
VF6MHVCH
VF6MHVRB
VF6MHVRBCH
VF6SVRCH
VF8MHVCH
VF8MHVRBCH
VFHVRB
VFHVRB (INCH)
VFJHV
VFMD
VFMFPR
VFMHV
VFMHVCH
VFMHVRB
VFMHVRBCH
VFSD
VFSFPR
VFSFPRCH
I001
SOLID END MILLS
PRODUCT CODE CORRESPONDENCES

PRODUCT CODE OF END MILLS
End mill names
Number of
utes
Flute length
Features
DS
: Diamond star end mills
2 : 2ute
ES : Extra short
: General use
MS
: Mstar end mills
3 : 3ute
: Short
: Center cut
ex.
VC
: Miracle end mills
4 : 4ute
: Medium
: Ball nose
D0050 |& 0.5 mm
: Impact Miracle end mills
5 : 5ute
: Semi long
: For light alloy
D0500 |& 5 mm
DF
: Diamond coated end mills
6 : 6ute
: Long
: For high hardened
: Carbide end mills
8 : 8ute
: Taper neck
V
: Irregular helix utes
XL : Long neck
material
of
*** : Radius
ball nose
ex.
R0050 | R0.5
: High helix 45
: Roughing
FPR : Roughing
T
: Taper
TB : Taper ball nose

CH : Coolant hole
SOLID END MILLS
RB : Corner radius
HH : High helix 60
I002
*** : Diameter
VF
CBN : CBN end mills
Others
Dimensions
R0500 | R5
Shank diameter
** :: Neck
** : Taperlength
one side
T
** : Lengthangle
L
of cut
** : Overall length
A
**
S
SYMBOL DESCRIPTIONS
Tool material
Coating
IMPACT Miracle Coating
UWC
Ultra micro grain carbide
Single phase nano crystal coating technology

for higher lm hardness and heat resistance.
CBN
Cubic boron nitride
MIRACLE Coating
Tolerances
Original developed (Al, Ti)N

coating
Outside diameter tolerance

Indicates the diameter tolerance of the end mill.
Diamond Coating
R tolerance
Angle, sharp corner edge and gash land
R tolerance
Helix angle
Indicates the radial tolerance of an end mill with a

corner radius.
Indicates the helix angle of the end mill.
Tolerance of Taper angle
Sharp corner edge
Indicates the tolerance of the taper angle.
Indicates that the end mill has a sharp corner edge.
Gash land
Tolerance of Point angle
Indicates that the end mill cutting edge has a gash

land.
Indicates the tolerance of the point angle.
Tolerance of Shank
Coverage
Indicates the tolerance of the end mill shank.

HRC
<55
The best for hardened steels equal to under 55HRC.
SOLID END MILLS
Indicates the radius tolerance of a ball nose end mill.
I003
SOLID END MILLS

CARBIDE
END MILLS SELECTION CHART
CARBIDE
INCH
DS2SS
Short, 2 ute
Medium cut length, 2 ute
Medium, 2 ute
Semi long cut length, 2 ute
long cut length, 2 ute
& 0.2 12
INCH
DS2LS
Long, 2 ute
General
& 0.1 12
METRIC
MS2LS
SQUARE
& .0156 1.250
METRIC
MS2JS
SOLID END MILLS
& 0.2 20
INCH
DS2MS
& .1250 1.000
INCH
DS3SC
Short, 3 ute
& .0156 .7500
INCH
DS3MC
Medium, 3 ute
& .0156 1.250
METRIC
MS4SC
Short cut length, 4 ute
& 1 12
INCH
DS4SC
Short, 4 ute
& .0156 .7500
METRIC
MS4MC
Medium cut length, 4 ute
& .0156 .7500
METRIC
MS2MS
& 0.1 12
& 1 20
INCH
DS4MC
Medium, 4 ute
& .0156 1.250
METRIC
MS4JC
Semi long cut length, 4 ute
& 1 12
INCH
DS4LC
Long, 4 ute
& .1250 1.000
e : Excellent
I004
Titanium Alloy,
Austenitic Stainless Steel
Page
u u
I050
I194
e e u
u u
I014
I192
e e u
u u
I051
I194
e e u
u u
I015
I192
e e u
u u
I054
I196
e e u
u u
I055
I197
e e u
u u
I016
I192
e e u
u u
I017
I192
e e u
u u
I018
I192
e e u
u u
I068
I207
e e u
u u
I019
I192
e e u
u u
I069
I207
e e u
u u
I020
I192
e e u
u u
I070
I208
e e u
u u
I021
I192
u : Good
Copper Alloy
e e u
Aluminum Alloy
Cutting
Conditions
Short cut length, 2 ute
M S
Dimensions
METRIC
MS2SS
Cutting
Diameter
Range
Tool Steel, Pre-Hardened Steel, Hardened Steel
Shape
Hardened Steel (55HRC)

Order
Number
Carbon Steel, Alloy Steel, Cast Iron
Coating
Number of Flutes
Type
Shape
Work Material
P
None : Not Recommended
CARBIDE
INCH
e e u
e u
High Helix
Medium cut length, 3 ute for drilling and slotting & .0625 .7500
METRIC
MSSHD
High power, Short cut length, 4 ute
METRIC
MSMHD
High power, Medium cut length, 4 ute
High power, Semi long cut length, 4 ute
Medium cut length, 2 ute, Strong geometry type
For Hardened Steel
Medium cut length, 4 ute, Irregular helix utes
Short cut length, For hardened materials
& 1 12
METRIC
VFMD
Medium cut length, For hardened materials
& 1 25
METRIC
Medium cut length, 4 6 ute
& 0.5 3
METRIC
VCLD
Long cut length, 6 ute
& 6 25
INCH
DS3SH-SS
Short, 3 ute, For stainless steel
& .1250 .7500
INCH
DS3MH-SS
Medium, 3 ute, For stainless steel
& .1250 .7500
INCH
DS3MHH60
High helix, Medium, 3 ute
3
4
& 6 20
METRIC
VFSD
& 0.5 6
METRIC
VF4MV
VCMDSC
For Difcult-to-cut Material
SQUARE
& 1 12
METRIC
VF2MV
4
6
& 2 20
METRIC
MS2MD
& 2 25
METRIC
MSJHD
& 3 20
& .1250 1.000
METRIC
VCMH
Medium cut length, 34 ute, High helix angle
& 3 25
e : Excellent
Cutting
Conditions
Dimensions
I066
INCH
I205
INCH
I067
I206
e e u
e e
I062
I203
e e u
e e
I063
I203
e e u
e e
I065
I204
e e u
e e
I053
I195
u e e e
I140
I240
u e e e
I141
I241
u e e e
I148
I245
u e e e
I149
I245
u e e e
I112
I220
u e e e
I113
I221
u u
e e
I038
I192
u u
e e
I039
I192
u u u
e e
I027
I192
u e u
e e
I114
I222
u : Good
SOLID END MILLS
& 1 20
MSMHZD
Copper Alloy
METRIC METRIC
METRIC
Page
Aluminum Alloy
Titanium Alloy,
M S
Cutting
Diameter
Range
Shape
H
Order
Number
Coating
Number of Flutes
Type
Shape
Work Material
P
I005
SOLID END MILLS

CARBIDE
CARBIDE
VFMHVCH
SQUARE
SOLID END MILLS
Long, 5 ute, For stainless steel

Medium cut length, 6 ute,
Irregular helix utes with multiple internal through coolant holes
VF8MHVCH

For Aluminum Alloy
& 6 20
u u u
e e
I144
I243
u u
e e
I040
I192
u u
e e
I041
I192
u u u
e e
I028
I192
e e u
e e
I115
I223
u u u
e e
I145
I244
e e
I146
I261
e e
I147
I262
e e
I116
I223
I190
I273
u e
I188
I272
u e
I189
I272
& 16 ,& 20
& 20 25
e e u
METRIC
C2MHA
2 ute, Medium cut length, Relieved neck
& 3 25
METRIC
C2SA
2 ute, Short cut length, Relieved neck
& 3 20
METRIC
C3SA
& 10 26
e : Excellent
u : Good
Copper Alloy
I261
Aluminum Alloy
I143
& 16 ,& 20
METRIC

Titanium Alloy,
e e
METRIC
I006
I242
METRIC
VF6MHVCH
VC8MH
& 6 25
METRIC
VF6MHV
& .1250 1.000
METRIC
VC6MH
& .2500 .7500
INCH
DS6MHH60
& .2500 .7500
INCH
DS5LH-SS
& 2 20
INCH
DS5MH-SS
I142
& 16 ,20
METRIC
Semi long cut length, 4 ute, Irregular helix utes
e e
u u u
METRIC

Irregular helix utes, with multiple internal through coolant holes
VFJHV
& 6 20
Page
Cutting
Conditions
Medium cut length, Irregular helix utes
M S
Dimensions
METRIC
VFMHV
Cutting
Diameter
Range
Shape
Order
Number
H
Coating
Number of Flutes
Type
Shape
Work Material
P
CARBIDE
& 3 12
METRIC
4 ute, For Swiss type lathes
& 3 14
Titanium Alloy,
I075
I209
e e u
u u
I076
I209
e e u
u u
I077
I209
Semi long cut length, 4 ute, For graphite
& 3 12
I178
I264
I179
I265
Graphite : e
GFPR,CFPR : u
METRIC
DF4XL
Long neck, 4 ute, For graphite
& 1 12
METRIC METRIC
Rib Processing
& 0.2 6
INCH
Short cut length, 2 ute, Long neck
Short cut length, 2 ute, 6mm shank
& 0.3 2.5

& 1 10
MS4XL
INCH
Short cut length, 4 ute, Long neck
Curved Surface Machining
u u
e e u
u u
e e u
u u
2 ute, Long neck
& 0.1 3
METRIC
R0.1 6
INCH
DS2SB
Ball nose, Short, 2 ute
& .0625 .2500
METRIC
VF2XL
& .0156 .7500
METRIC
MS2MB
Ball nose, Medium cut length, 2 ute
R0.25 6
INCH
DS2LB
Ball nose, Long, 2 ute
& .1250 1.000
METRIC
VC2ESB
Ball nose, Extra short cut length, 2 ute
R0.15 6
e : Excellent
I056
INCH
I198
INCH
I061
I201
I059
I199
METRIC METRIC
METRIC
MS2SB
BALL
e e u
& .0516 .2500
METRIC
MS2XL6
For
Hardened Steel
LONG NECK SQUARE
METRIC
MS2XL
Copper Alloy
u u
Aluminum Alloy
e e u
METRIC
DF4JC
Page
u e e e
I071
INCH
I200
INCH
I074
I202
I138
I239
e e u
u u
I078
I210
e e u
u u
I022
I193
e e u
u u
I079
I210
e e u
u u
I023
I193
u e e u u u
I118
I225
u : Good
SOLID END MILLS
METRIC
MS3ES
& 3 12
M S
Cutting
Conditions
METRIC
MS2ES
Cutting
Diameter
Range
Shape
Dimensions
For Swiss
Type Lathes
Order
Number
MS4EC
For Graphite
SQUARE
Coating
Number of Flutes
Type
Shape
Work Material
P
I007
SOLID END MILLS

CARBIDE
CARBIDE
INCH
DS4SB
For Complex
Geometry
Ball nose, Short cut length, 2 ute, Strong geometry
Ball nose, Short cut length, 2 ute, For hardened materials
R0.1 10
METRIC
VF4MB
R0.5 6
METRIC
High Precision
R0.5 6
METRIC
VF2SB
VC4MB
Taper Long
neck Shank
R0.5 10
METRIC
R0.5 10
METRIC
VC2PSB
Ball nose, Short cut length, 2 ute, High precision
R0.05 6
METRIC
VC2PSBP
Ball nose, Short cut length, 2 ute, Ultra high precision
R0.02 6
METRIC
VF2SDBL
Ball nose, Short cut length, 2 ute, Strong geometry, Long shank
R1 3
METRIC
VF2SSB
& .1250 1.000
METRIC
Wide ball nose, Medium neck, 2 ute
& .0312 .7500
INCH
DS4LB
VF2SDB
R1 10
R0.5 10
METRIC
VF3XB
R0.4 2.5
Titanium Alloy,
I193
u e e u u u
I123
I228
e e u
u u
I025
I193
e e u
u u
I026
I193
e e u
e e
I154
I248
u e e u
I157
I250
u e e e u u
I155
I249
u e e e u u
I156
I249
e e e u u
I168
I254
u e e e u u
I124
I229
e e e
u u
I119
I226
e e e
u u
I120
I226
u e e u
I158
I250
u e e e u u
I165
I252
Copper Alloy
I024
Aluminum Alloy
u u
e e u
Ball nose, 3 ute, Taper neck

e : Excellent
I008
Page
Cutting
Conditions
VF2WB
For Hardened Steel
BALL
METRIC
VC3MB
& .1250 .7500
M S
Dimensions
Cutting
Diameter
Range
INCH
DS3SB
SOLID END MILLS
Shape
H
Coating
Number of Flutes
Type
Order
Number
Strong
Curved Surface Machining
Shape
Work Material
P
u : Good
CARBIDE
For Difcult-to-cut
Material
BALL
INCH
DS3SHB-SS
Ball nose, Short, 3 ute, For stainless steel
Ball nose, Medium, 3 ute, For stainless steel
Ball nose, Short cut length, 4 ute, Variable curve
For Graphite
Ball nose, Medium cut length, 2 ute, For graphite
Ball nose, 2 ute, Long neck, For graphite
Deep Slotting
Ball nose, Long neck, 2 ute, For hardened materials
Titanium Alloy,
u u
e e
I042
I193
u u
e e
I043
I193
u u
e e
I169
I255
I180
I266
I181
I267
I183
I268
I160
I251
I159
I251
Graphite : e
GFPR,CFPR : u
R0.1 3
R0.2 1
u e e e
u e e e
METRIC
R0.1 3
MS2XLB
INCH
METRIC METRIC
e e u
u u
Ball nose, Short cut length, 2 ute, Long neck R.0078 .1250
INCH
MS4XLB
Ball nose, 4 ute, Long neck
INCH
DS2SRB
Corner radius, Short, 2 ute
R.0313 .1250
& .1250 .7500
METRIC
MS2MRB
Corner radius, Medium cut length, 2 ute
& 1 12
INCH
DS2MRB
Corner radius, Medium, 2 ute
& .1250 .7500

e : Excellent
Copper Alloy
I227
Aluminum Alloy
I121
R0.5 2
METRIC
VF2XLBS
Ball nose, Long neck, 2 ute, Short shank
Corner Radius
R0.2 2
METRIC
VF2XLB
LONG NECK BALL
u e e u u u
METRIC
DF3XB
Ball nose, 3 ute, Taper neck, For graphite
RADIUS
I213
R3 6
METRIC
DF2XLB
R3 10
I087
METRIC
DF2MB
& .1250 .7500
METRIC
VF4SVB
& .1250 .7500
INCH
DS3MHB-SS
R0.5 6
u u
e e u
SOLID END MILLS
METRIC
VCXB
R0.1 2
Page
Cutting
Conditions
M S
Dimensions
METRIC
MS2XB
Cutting
Diameter
Range
Shape
H
Order
Number
Coating
Number of Flutes
Type
Taper neck
Shape
Work Material
P
I080
INCH
I211
INCH
I085
I212
e e u
u u
I086
I212
e e u
u u
I031
I192
e e u
u u
I090
I194
e e u
u u
I032
I192
u : Good
I009
SOLID END MILLS

CARBIDE
CARBIDE
METRIC
MS4MRB
Corner Radius
Corner radius, Medium cut length, 4 ute
INCH
DS4MRB
Corner radius, Semi long cut length, 4 ute
Corner radius, Medium cut length, 4 ute, High helix angle
High For Hardened

High
Feed Precision
Steel
& 2 20
METRIC
VCMHDRB
& 2 25
&14
VFHVRB
4 ute, Corner radius, Short cut length, Irregular helix utes
2
4
VCPSRB
VCHFRB
INCH

Titanium Alloy,
I192
e e u
u u
I093
I215
e e u
u u
I034
I192
u e e u u u
I129
I232
e e e
e e
I095
I216
u e e u e e
I133
I235
& 0.6 12
METRIC METRIC
e e e e u u
e e e e u u
& 2 16
High feed corner radius, 4 ute
Corner radius, Short, 3 ute, For stainless steel
DS3MHRB-SS
Corner radius, Medium, 3 ute, For stainless steel
DS3MHHRB
Corner radius, High helix, Medium, 3 ute
Corner radius, Medium cut length, 4 ute, Irregular helix utes
Corner radius, Medium cut length,

4 ute, Irregular helix utes, with multiple internal through coolant holes
e e e u
& .125 .500
I256
INCH
I172
I260
I125
I230
I130
INCH
I233
INCH
I132
I234
INCH
u u
e e
I044
I192
INCH
u u
e e
I045
I192
INCH
u u u
e e
I048
I192
u u u
e e
I173
I242
e e
I174
I261
& .1250 .7500
& .1250 .7500
& .1250 .6250
METRIC
VFMHVRB
I170
INCH
METRIC METRIC
METRIC
INCH
Copper Alloy
I033
Aluminum Alloy
u u
& .125 . 500
METRIC
Corner radius, Short cut length, 2-4 ute, High precision type
VFMHVRBCH
& 6 20
METRIC
& 16 20
e : Excellent
I010
e e u
METRIC
DS3SHRB-SS
& 3 20
METRIC
High power, Corner radius, Medium cut length, 4 ute
RADIUS
& .1250 .7500
METRIC
VC4JRB
MSMHDRB
SOLID END MILLS
& 3 20
Page
Cutting
Conditions
& .1250 .7500
M S
Dimensions
INCH
DS4SRB
Cutting
Diameter
Range

Shape
Order
Number
H
Coating
Number of Flutes
Type
Shape
Work Material
P
u : Good
CARBIDE
INCH
DS6MHHRB
Corner radius, Medium cut length, 6 ute, Irregular helix utes

VF8MHVRBCH

Corner radius, Short cut length, 3 ute, For aluminum alloy
MS2XLRB
Titanium Alloy,
u u u
e e
I049
I192
u u u
e e
I175
I244
e e
I176
I261
e e
I177
I262
u e
I035
I192
u e
I036
I192
u e
I191
I272
I184
I269
& 16 20
& .1875 1.000
& .1875 1.000
& 12 25
& 0.5 12
METRIC
Corner radius, Short cut length, 2 ute, Long neck
&16
METRIC
MS4LT
Taper, Long cut length, 4 ute
& 0.2 3
METRIC
MS4LTB
Ball nose, 4 ute, Taper, For rib milling
R0.3 1
e : Excellent
Copper Alloy
I192
Graphite : e
GFPR,CFPR : u
Aluminum Alloy
I047
& 16 20
METRIC
Corner radius, Short cut length, 2-4 ute, High precision, For graphite
e e
METRIC
C3SARB
DFPSRB
u u
INCH
DS2SRB-NAo
2
4
I192
INCH
DS2SRB-Ao
Corner radius, Short, 2 ute, Neck relief
I046
METRIC
Corner radius, Short, 2 ute, For aluminum alloys

& 6 20
e e
METRIC
VF6MHVRBCH
& .1250 .6250
METRIC
VF6MHVRB
& .2500 .7500
u u
e e u
u u
I092
I214
e e u
I101
I218
e e u
u u
I108
I219
u : Good
SOLID END MILLS
8
For
Rib Processing General Graphite
For Aluminum Alloy
RADIUS
LONG NECK
TAPER
BALL TAPER RADIUS
INCH
DS5MHRB-SS
& .2500 .7500
Page
Cutting
Conditions
M S
Dimensions
INCH
DS5SHRB-SS
Cutting
Diameter
Range
Shape
H
Order
Number
Coating
Number of Flutes
Type
Shape
Work Material
P
I011
SOLID END MILLS

CARBIDE
CARBIDE
METRIC
MS2MTB
Ball nose taper, Medium cut length, 2 ute
Ball nose taper, Short cut length, 4 ute
Roughing
Chipbreaker, Medium, 4 ute
Chipbreaker, Long, 4 ute
ROUGHING
SOLID END MILLS
Roughing, Short cut length, 3 4 ute
Roughing, Short cut length, 34 ute
VFSFPRCH
Roughing, Short cut length,

4 ute, with multiple internal through coolant holes
VF6SVRCH
Roughing, Short cut length,

VFMFPR
Roughing
Chamfering Aluminum Alloy
& 3 20
Titanium Alloy,
e e u
u u
I107
I210
u e e e u u
I135
I236
e e u
u u
I029
I192
e e u
u u
I030
I192
e e u
e e
I117
I224
e e u
e e
I150
I246
e e
I151
I262
e e
I152
I263
e e
I153
I247
I037
I192
I137
I238
& 16, 20
e e u
INCH
DS3MHR-A
Roughing, Medium, 3 ute, For aluminum alloys
& .2500 1.000
METRIC
VC2C
Chamfer cutter, 2 ute
& 2 12
e e e u e e
u : Good
Copper Alloy
I217
Aluminum Alloy
I097
METRIC
& 5 20
u u
& 16, 20
e : Excellent
I012
e e u
METRIC
METRIC
Roughing, Medium cut length, 4 ute
CHAMFERING
& 3 20
METRIC
VFSFPR
& .1250 1.000
METRIC
VCSFPR
& .1250 1.000
INCH
DS4LC-CB
R0.3 4
INCH
DS4MC-CB
3
4
R0.2 1.5
METRIC
VC4STB
& 0.2 10
Cutting
Conditions
Taper, Medium cut length, 2 ute
Page
Dimensions
METRIC
MS2MT
Cutting
Diameter
Range
M S
Shape
Order
Number
H
Coating
Number of Flutes
Type
Slope Machining
TAPER BALL
TAPER
Shape
Work Material
P
2
Coating
Number of Flutes
Type
Shape
Order
Number
Shape
CBN2XLB
Ball nose, Short cut length, 2 ute, Long neck
CBN2XLRB
Corner radius, Short cut length, 2 ute, Long neck
METRIC
&0.5 2
e : Excellent
Cutting
Conditions
R0.2 1
Dimensions
METRIC
Cutting
Diameter
Range
u e e e
I186
I270
u e e e
I187
I271
u : Good
Aluminum Alloy
M S
Copper Alloy
Titanium Alloy,
H
CBN
Work Material
SOLID END MILLS
LONG NECK LONG NECK

RADIUS
BALL
High
Precision

CBN
Page
I013
DS2SS
Short, 2 ute
(<30HRC)
( < 45HRC)
CARBIDE
D1 < .0156"
.0312" < D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.001"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
Type 2
HRC
<55
UWC

a Helix angle 30.
BALL
Unit : Inch
TAPER
RADIUS
DS2SSD1/64
D1/32
D3/64
D1/16
D5/64
D3/32
D7/64
D1/8
D9/64
D5/32
D11/64
D3/16
D13/64
D7/32
D15/64
D1/4
D9/32
D5/16
D3/8
D7/16
D1/2
D5/8
D3/4
SOLID END MILLS
I014
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.0156
.0312
.0469
.0625
.0781
.0938
.1094
.1250
.1406
.1562
.1719
.1875
.2031
.2187
.2344
.2500
.2813
.3125
.3750
.4375
.5000
.6250
.7500
.023
.063
.094
.125
.156
.188
.219
.250
.313
.313
.375
.375
.500
.500
.500
.500
.500
.500
.563
.625
.625
.750
1.000
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.500
2.500
3.000
3.000
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.188
.188
.250
.250
.250
.250
.313
.313
.375
.438
.500
.625
.750
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
a
a
a
r
a
r
a
r
r
r
a
r
r
r
a
r
r
a
r
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
2
2
2
2
2
I192
DS2MS
Medium, 2 ute
(<30HRC)
( < 45HRC)
D1 < .0156"
.0312" < D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
.750 < D4 < 1.000"
D4 = 1.250"
0 -.001"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
0 -.00063"
Aluminum Alloy
CARBIDE
Type 2
HRC
<55
UWC
SQUARE
Type 1
DS2MSD1/64
D1/32
D3/64
D1/16
D5/64
D3/32
D7/64
D1/8
D9/64
D5/32
D11/64
D3/16
D13/64
D7/32
D15/64
D1/4
D9/32
D5/16
D3/8
D7/16
D1/2
D9/16
D5/8
D3/4
D7/8
D1
D1-1/4
.0156
.0312
.0469
.0625
.0781
.0938
.1094
.1250
.1406
.1562
.1719
.1875
.2031
.2187
.2344
.2500
.2813
.3125
.3750
.4375
.5000
.5625
.6250
.7500
.8750
1.000
1.250
.040
.078
.109
.188
.234
.281
.328
.375
.500
.500
.563
.563
.625
.625
.750
.750
.750
.813
.875
1.000
1.000
1.125
1.250
1.500
1.500
1.500
1.563
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
2.000
2.000
2.000
2.000
2.500
2.500
2.500
2.500
2.500
2.500
2.500
2.750
3.000
3.500
3.500
4.000
4.000
4.000
4.375
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.188
.188
.250
.250
.250
.250
.313
.313
.375
.438
.500
.563
.625
.750
.875
1.000
1.250
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
r
a
r
a
r
r
r
a
r
r
r
a
r
r
a
r
a
a
a
a
a
r
r
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
2
2
2
2
2
2
2
2
2
2
I192
RADIUS
Shank
Dia.
D4
TAPER
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
SOLID END MILLS
Unit : Inch
BALL

a Helix angle 30.
I015
DS2LS
Long, 2 ute
(<30HRC)
( < 45HRC)
CARBIDE
D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
.750 < D4 < 1.000"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
HRC
<55
UWC

a Helix angle 30.
BALL
Unit : Inch
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
1.000
1.000
1.125
1.250
1.375
1.500
1.750
2.000
2.500
3.000
3.000
2.500
3.000
3.000
3.250
3.500
4.000
4.000
4.625
5.250
6.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
1.000
2
2
2
2
2
2
2
2
2
2
Order Number
a
a
r
a
r
a
a
a
r
1
1
1
1
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
DS2LSD1/8
D3/16
D1/4
D5/16
D3/8
D7/16
D1/2
D5/8
D3/4
D1
Type
I016
CUTTING CONDITIONS
I192
DS3SC
Short, 3 ute
(<30HRC)
( < 45HRC)
D1 < .0156"
.0312" < D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.001"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
Type 2
HRC
<55
UWC
SQUARE
Type 1
DS3SCD1/64
D1/32
D3/64
D1/16
D5/64
D3/32
D7/64
D1/8
D9/64
D5/32
D11/64
D3/16
D13/64
D7/32
D15/64
D1/4
D9/32
D5/16
D3/8
D7/16
D1/2
D5/8
D3/4
.0156
.0312
.0469
.0625
.0781
.0938
.1094
.1250
.1406
.1562
.1719
.1875
.2031
.2187
.2344
.2500
.2813
.3125
.3750
.4375
.5000
.6250
.7500
.023
.063
.094
.125
.156
.188
.219
.250
.313
.313
.375
.375
.500
.500
.500
.500
.500
.500
.563
.625
.625
.750
1.000
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.500
2.500
3.000
3.000
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.188
.188
.250
.250
.250
.250
.313
.313
.375
.438
.500
.625
.750
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
a
a
a
a
r
a
r
a
r
r
r
a
r
r
r
a
r
r
a
r
a
a
r
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
2
2
2
2
2
I192
RADIUS
Shank
Dia.
D4
TAPER
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
SOLID END MILLS
Unit : Inch
BALL

a Helix angle 30.
I017
DS3MC
Medium, 3 ute
(<30HRC)
( < 45HRC)
CARBIDE
D1 < .0156"
.0312" < D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
.750 < D4 < 1.000"
D4 = 1.250"
0 -.001"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
0 -.00063"
Aluminum Alloy
SQUARE
Type 1
Type 2
HRC
<55
UWC

a Helix angle 30.
BALL
Unit : Inch
TAPER
RADIUS
DS3MCD1/64
D1/32
D3/64
D1/16
D5/64
D3/32
D7/64
D1/8
D9/64
D5/32
D11/64
D3/16
D13/64
D7/32
D15/64
D1/4
D9/32
D5/16
D3/8
D7/16
D1/2
D9/16
D5/8
D3/4
D7/8
D1
D1-1/4
SOLID END MILLS
I018
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.0156
.0312
.0469
.0625
.0781
.0938
.1094
.1250
.1406
.1562
.1719
.1875
.2031
.2187
.2344
.2500
.2813
.3125
.3750
.4375
.5000
.5625
.6250
.7500
.8750
1.000
1.250
.040
.078
.109
.188
.234
.281
.328
.375
.500
.500
.563
.563
.625
.625
.750
.750
.750
.813
.875
1.000
1.000
1.125
1.250
1.500
1.500
1.500
1.563
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
2.000
2.000
2.000
2.000
2.500
2.500
2.500
2.500
2.500
2.500
2.500
2.750
3.000
3.500
3.500
4.000
4.000
4.000
4.375
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.188
.188
.250
.250
.250
.250
.313
.313
.375
.438
.500
.563
.625
.750
.875
1.000
1.250
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
Order Number
a
r
a
a
a
a
a
r
r
r
a
r
r
r
a
r
a
a
r
a
a
a
a
r
r
r
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
2
2
2
2
2
2
2
2
2
I192
DS4SC
Short, 4 ute
(<30HRC)
( < 45HRC)
D1 < .0156"
.0312" < D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.001"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
Type 2
HRC
<55
UWC
SQUARE
Type 1
.0156
.0312
.0469
.0625
.0781
.0938
.1094
.1250
.1406
.1562
.1719
.1875
.2031
.2187
.2344
.2500
.2813
.3125
.3750
.4375
.5000
.6250
.7500
.023
.063
.094
.125
.156
.188
.219
.250
.313
.313
.375
.375
.500
.500
.500
.500
.500
.500
.563
.625
.625
.750
1.000
Shank
Dia.
D4
No. of
Flutes
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.500
2.500
3.000
3.000
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.188
.188
.250
.250
.250
.250
.313
.313
.375
.438
.500
.625
.750
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
r
a
r
a
r
r
r
a
r
r
r
a
r
r
a
r
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
2
2
2
2
2
I192
RADIUS
DS4SCD1/64
D1/32
D3/64
D1/16
D5/64
D3/32
D7/64
D1/8
D9/64
D5/32
D11/64
D3/16
D13/64
D7/32
D15/64
D1/4
D9/32
D5/16
D3/8
D7/16
D1/2
D5/8
D3/4
Overall
Length
L1
TAPER
D1
Length of
Cut
ap
SOLID END MILLS
Dia.
Order Number
Stock
Unit : Inch
BALL

a Helix angle 30.
I019
DS2SS
DS4MC
Short, 2 4ute
Medium,
ute
(<30HRC)
( < 45HRC)
CARBIDE
4 4== .125"
DD
4 4== .188"
DD
.188"
< D4 < .375"
.250
4 < .375"
.250<<DD
4 < .625"
.438
.438<<DD
.625"
<<
44
1.000"
.750
.750"
44
==1.250"
DD
<<
11
DD
.0156"
.0156" 00-.001"
-.001"
<<
11
.0312"
.0312"<<DD
-.002"
.2500"
.2500" 00-.002"
1 1>>
.2500"
.2500" 00-.003"
-.003"
DD
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0
-.00031"
0
-.00031"
0
-.00035"
0
-.00035"

0
-.00043"
-.00051"
0
-.00043"
0
-.00051"
0 -.00063"
Aluminum Alloy
SQUARE
Type 1
Type 2
HRC
<55
UWC

a Helix angle 30.
BALL
Unit : Inch
TAPER
RADIUS
DS4MCD1/64
D1/32
D3/64
D1/16
D5/64
D3/32
D7/64
D1/8
D9/64
D5/32
D11/64
D3/16
D13/64
D7/32
D15/64
D1/4
D9/32
D5/16
D3/8
D7/16
D1/2
D9/16
D5/8
D3/4
D7/8
D1
D1-1/4
SOLID END MILLS
I020
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.0156
.0312
.0469
.0625
.0781
.0938
.1094
.1250
.1406
.1562
.1719
.1875
.2031
.2187
.2344
.2500
.2813
.3125
.3750
.4375
.5000
.5625
.6250
.7500
.8750
1.000
1.250
.040
.078
.109
.188
.234
.281
.328
.375
.500
.500
.563
.563
.625
.625
.750
.750
.750
.813
.875
1.000
1.000
1.125
1.250
1.500
1.500
1.500
1.563
1.500
1.500
1.500
1.500
1.500
1.500
1.500
1.500
2.000
2.000
2.000
2.000
2.500
2.500
2.500
2.500
2.500
2.500
2.500
2.750
3.000
3.500
3.500
4.000
4.000
4.000
4.375
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.188
.188
.250
.250
.250
.250
.313
.313
.375
.438
.500
.563
.625
.750
.875
1.000
1.250
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Order Number
a
a
a
r
a
r
r
r
a
r
a
r
r
r
a
r
a
a
a
a
a
a
a
a
r
r
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
2
2
2
2
2
2
2
2
2
I192
DS4LC
Long, 4 ute
(<30HRC)
( < 45HRC)
D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
.750 < D4 < 1.000"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
SQUARE
Type 1
HRC
<55
UWC
Shank
Dia.
D4
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
1.000
1.000
1.125
1.250
1.375
1.500
1.750
2.000
2.500
3.000
3.000
2.500
3.000
3.000
3.250
3.500
4.000
4.000
4.625
5.250
6.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
1.000
4
4
4
4
4
4
4
4
4
4
a
a
a
r
a
r
a
a
a
r
1
1
1
1
1
1
1
1
1
1
SOLID END MILLS
DS4LCD1/8
D3/16
D1/4
D5/16
D3/8
D7/16
D1/2
D5/8
D3/4
D1
Type
RADIUS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
TAPER
Unit : Inch
BALL

a Helix angle 30.
CUTTING CONDITIONS
I192
I021
DS2SB
(<30HRC)
( < 45HRC)
CARBIDE
D1 < .0156"
.0312" < D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.001"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
UWC
Type 2
HRC
<55
a 2 ute ball nose end mill for general purpose.

a Helix angle 30.
BALL
Unit : Inch
TAPER
RADIUS
DS2SBD1/64
D1/32
D3/64
D1/16
D3/32
D1/8
D9/64
D5/32
D11/64
D3/16
D13/64
D7/32
D15/64
D1/4
D5/16
D3/8
D7/16
D1/2
D5/8
D3/4
SOLID END MILLS
I022
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.0156
.0312
.0469
.0625
.0938
.1250
.1406
.1562
.1719
.1875
.2031
.2187
.2344
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.023
.063
.094
.125
.188
.250
.313
.313
.375
.375
.500
.500
.500
.500
.500
.563
.625
.625
.750
1.000
1.500
1.500
1.500
1.500
1.500
1.500
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.500
2.500
3.000
3.000
.125
.125
.125
.125
.125
.125
.188
.188
.188
.188
.250
.250
.250
.250
.313
.375
.438
.500
.625
.750
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
a
a
a
a
a
r
r
r
a
r
r
r
a
r
a
r
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
2
1
1
1
2
1
1
1
2
2
2
2
2
2
2
I193
DS2LB
(<30HRC)
( < 45HRC)
D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
.750 < D4 < 1.000"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
UWC
SQUARE
Type 1
HRC
<55
Shank
Dia.
D4
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
1.000
1.000
1.125
1.250
1.375
1.500
1.750
2.000
2.500
3.000
3.000
2.500
3.000
3.000
3.250
3.500
4.000
4.000
4.625
5.250
6.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
1.000
2
2
2
2
2
2
2
2
2
2
a
a
a
r
a
r
a
a
a
r
1
1
1
1
1
1
1
1
1
1
SOLID END MILLS
DS2LBD1/8
D3/16
D1/4
D5/16
D3/8
D7/16
D1/2
D5/8
D3/4
D1
Type
RADIUS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
TAPER
Unit : Inch
BALL

a Helix angle 30.
CUTTING CONDITIONS
I193
I023
DS3SB
(<30HRC)
( < 45HRC)
CARBIDE
D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
UWC
HRC
<55

a Helix angle 30.
BALL
Unit : Inch
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.250
.375
.500
.500
.563
.625
.625
.750
1.000
1.500
2.000
2.000
2.000
2.000
2.500
2.500
3.000
3.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
3
3
3
3
3
3
3
3
3
Order Number
a
a
r
a
r
a
a
a
1
1
1
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
DS3SBD1/8
D3/16
D1/4
D5/16
D3/8
D7/16
D1/2
D5/8
D3/4
Type
I024
CUTTING CONDITIONS
I193
DS4SB
(<30HRC)
( < 45HRC)
D1 < .0156"
.0312" < D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.001"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
UWC
Type 2
HRC
<55
SQUARE
Type 1
DS4SBD1/32
D3/64
D1/16
D3/32
D1/8
D9/64
D5/32
D11/64
D3/16
D13/64
D7/32
D15/64
D1/4
D5/16
D3/8
D7/16
D1/2
D5/8
D3/4
.0312
.0469
.0625
.0938
.1250
.1406
.1562
.1719
.1875
.2031
.2187
.2344
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.063
.094
.125
.188
.250
.313
.313
.375
.375
.500
.500
.500
.500
.500
.563
.625
.625
.750
1.000
1.500
1.500
1.500
1.500
1.500
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.500
2.500
3.000
3.000
.125
.125
.125
.125
.125
.188
.188
.188
.188
.250
.250
.250
.250
.313
.375
.438
.500
.625
.750
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
r
r
r
a
r
r
r
a
r
a
r
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
2
1
1
1
2
1
1
1
2
2
2
2
2
2
2
I193
RADIUS
Shank
Dia.
D4
TAPER
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
SOLID END MILLS
Unit : Inch
BALL

a Helix angle 30.
I025
DS4LB
(<30HRC)
( < 45HRC)
CARBIDE
D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
.750 < D4 < 1.000"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
UWC
HRC
<55

a Helix angle 30.
BALL
Unit : Inch
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
1.000
1.000
1.125
1.250
1.375
1.500
1.750
2.000
2.500
3.000
3.000
2.500
3.000
3.000
3.250
3.500
4.000
4.000
4.625
5.250
6.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
1.000
4
4
4
4
4
4
4
4
4
4
Order Number
a
a
r
a
r
a
a
a
r
1
1
1
1
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
DS4LBD1/8
D3/16
D1/4
D5/16
D3/8
D7/16
D1/2
D5/8
D3/4
D1
Type
I026
CUTTING CONDITIONS
I193
DS3MHH60
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
D1 < .2500"
D1 > .2500"
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
.750 < D4 < 1.000"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
Type 2
HRC
<55
UWC
SQUARE
Type 1
.1250
.1562
.1875
.2187
.2500
.2813
.3125
.3750
.4375
.5000
.5625
.6250
.7500
.8750
1.000
.375
.500
.563
.625
.750
.750
.813
.875
1.000
1.000
1.125
1.250
1.500
1.500
1.500
Shank
Dia.
D4
No. of
Flutes
1.500
2.000
2.000
2.500
2.500
2.500
2.500
2.500
2.750
3.000
3.500
3.500
4.000
4.000
4.000
.125
.188
.188
.250
.250
.313
.313
.375
.438
.500
.563
.625
.750
.875
1.000
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
a
r
a
r
a
r
r
a
r
a
r
a
a
r
r
CUTTING CONDITIONS
Type
2
1
2
1
2
1
2
2
2
2
2
2
2
2
2
I192
RADIUS
DS3MHH60D1/8
D5/32
D3/16
D7/32
D1/4
D9/32
D5/16
D3/8
D7/16
D1/2
D9/16
D5/8
D3/4
D7/8
D1
Overall
Length
L1
TAPER
D1
Length of
Cut
ap
SOLID END MILLS
Dia.
Order Number
Stock
Unit : Inch
BALL
a 3 ute high helix square end mill for difcult to cut materials.
a Helix angle 60.
I027
DS6MHH60
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
D1 < .2500"
D1 > .2500"
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
.750 < D4 < 1.000"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
HRC
Type 2
<55
UWC
a 6 ute high helix square end mill for difcult to cut materials.
a Helix angle 60.
Dia.
TAPER
RADIUS
DS6MHH60D1/8
D5/32
D3/16
D7/32
D1/4
D9/32
D5/16
D3/8
D7/16
D1/2
D9/16
D5/8
D3/4
D7/8
D1
SOLID END MILLS
I028
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
.1250
.1562
.1875
.2187
.2500
.2813
.3125
.3750
.4375
.5000
.5625
.6250
.7500
.8750
1.000
.375
.500
.563
.625
.750
.750
.813
.875
1.000
1.000
1.125
1.250
1.500
1.500
1.500
1.500
2.000
2.000
2.500
2.500
2.500
2.500
2.500
2.750
3.000
3.500
3.500
4.000
4.000
4.000
.125
.188
.188
.250
.250
.313
.313
.375
.438
.500
.563
.625
.750
.875
1.000
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Order Number
Stock
BALL
Unit : Inch
a
r
a
a
a
r
r
a
r
a
r
a
r
r
r
CUTTING CONDITIONS
Type
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
I192
DS4MC
CB
Chipbreaker, Medium, 4 ute
D1 < .2500"
D1 > .2500"
aaa
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
.750 < D4 < 1.000"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
UWC
HRC
Type 2
<55
SQUARE
Type 1
DS4MCD1/8CB
D5/32CB
D3/16CB
D7/32CB
D1/4CB
D9/32CB
D5/16CB
D3/8CB
D7/16CB
D1/2CB
D9/16CB
D5/8CB
D3/4CB
D7/8CB
D1CB
.1250
.1562
.1875
.2187
.2500
.2813
.3125
.3750
.4375
.5000
.5625
.6250
.7500
.8750
1.000
.375
.500
.563
.625
.750
.750
.813
.875
1.000
1.000
1.125
1.250
1.500
1.500
1.500
1.500
2.000
2.000
2.500
2.500
2.500
2.500
2.500
2.750
3.000
3.500
3.500
4.000
4.000
4.000
.125
.188
.188
.250
.250
.313
.313
.375
.438
.500
.563
.625
.750
.875
1.000
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
r
r
r
r
a
r
r
a
r
a
r
a
r
r
r
CUTTING CONDITIONS
Type
2
1
2
1
2
1
2
2
2
2
2
2
2
2
2
I192
RADIUS
Shank
Dia.
D4
TAPER
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
SOLID END MILLS
Unit : Inch
BALL
a 4 ute chipbreaker end mill.

a Helix angle 30.
I029
DS4LC
CB
Chipbreaker, Long, 4 ute
D1 < .2500"
D1 > .2500"
aaa
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
.750 < D4 < 1.000"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
UWC
HRC
<55
a 4 ute chipbreaker end mill.

a Helix angle 30.
BALL
Unit : Inch
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
1.000
1.000
1.125
1.250
1.375
1.500
1.750
2.000
2.500
3.000
3.000
2.500
3.000
3.000
3.250
3.500
4.000
4.000
4.625
5.250
6.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
1.000
4
4
4
4
4
4
4
4
4
4
Order Number
r
a
r
a
r
a
a
r
r
1
1
1
1
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
DS4LCD1/8CB
D3/16CB
D1/4CB
D5/16CB
D3/8CB
D7/16CB
D1/2CB
D5/8CB
D3/4CB
D1CB
Type
I030
CUTTING CONDITIONS
I192
DS2SRB
(<30HRC)
( < 45HRC)
D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.500 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
UWC
SQUARE
Type 1
HRC
<55
DS2SRBD1/8R0.008
D3/16R0.015
D1/4R0.008
D1/4R0.020
D3/8R0.020
D3/8R0.040
D1/2R0.015
D1/2R0.030
D1/2R0.060
D5/8R0.020
D5/8R0.040
D3/4R0.030
D3/4R0.060
.1250
.1875
.2500
.2500
.3750
.3750
.5000
.5000
.5000
.6250
.6250
.7500
.7500
.008
.015
.008
.020
.020
.040
.015
.030
.060
.020
.040
.030
.060
.250
.375
.500
.500
.563
.563
.625
.625
.625
.750
.750
1.000
1.000
1.500
2.000
2.000
2.000
2.000
2.000
2.500
2.500
2.500
3.000
3.000
3.000
3.000
.125
.188
.250
.250
.375
.375
.500
.500
.500
.625
.625
.750
.750
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
r
r
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
I192
RADIUS
Shank
Dia.
D4
TAPER
Overall
Length
L1
Dia.
Order Number
SOLID END MILLS
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
Stock
Unit : Inch
BALL
a 2 ute radius end mill.

a General purpose.
I031
DS2MRB
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
D1 < .2500"
D1 > .2500"
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.500 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
UWC
HRC
<55

a General purpose.
Overall
Length
L1
Shank
Dia.
D4
.1250
.1875
.2500
.2500
.3750
.3750
.5000
.5000
.5000
.6250
.6250
.7500
.7500
.008
.015
.008
.020
.020
.040
.015
.030
.060
.020
.040
.030
.060
.375
.563
.750
.750
.875
.875
1.000
1.000
1.000
1.250
1.250
1.500
1.500
1.500
2.000
2.500
2.500
2.500
2.500
3.000
3.000
3.000
3.500
3.500
4.000
4.000
.125
.188
.250
.250
.375
.375
.500
.500
.500
.625
.625
.750
.750
2
2
2
2
2
2
2
2
2
2
2
2
2
Dia.
Order Number
TAPER
RADIUS
DS2MRBD1/8R0.008
D3/16R0.015
D1/4R0.008
D1/4R0.020
D3/8R0.020
D3/8R0.040
D1/2R0.015
D1/2R0.030
D1/2R0.060
D5/8R0.020
D5/8R0.040
D3/4R0.030
D3/4R0.060
SOLID END MILLS
I032
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
Stock
BALL
Unit : Inch
a
a
a
a
a
a
a
a
a
a
r
r
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
I192
DS4SRB
(<30HRC)
( < 45HRC)
D1 < .2500"
D1 > .2500"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.500 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
UWC
SQUARE
Type 1
HRC
<55
Shank
Dia.
D4
DS4SRBD1/8R0.008
D3/16R0.015
D1/4R0.008
D1/4R0.020
D3/8R0.020
D3/8R0.040
D1/2R0.015
D1/2R0.030
D1/2R0.060
D5/8R0.020
D5/8R0.040
D3/4R0.030
D3/4R0.060
.1250
.1875
.2500
.2500
.3750
.3750
.5000
.5000
.5000
.6250
.6250
.7500
.7500
.008
.015
.008
.020
.020
.040
.015
.030
.060
.020
.040
.030
.060
.250
.375
.500
.500
.563
.563
.625
.625
.625
.750
.750
1.000
1.000
1.500
2.000
2.000
2.000
2.000
2.000
2.500
2.500
2.500
3.000
3.000
3.000
3.000
.125
.188
.250
.250
.375
.375
.500
.500
.500
.625
.625
.750
.750
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
r
r
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
I192
RADIUS
Overall
Length
L1
TAPER
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
Order Number
SOLID END MILLS
Unit : Inch
BALL

a General purpose.
I033
DS4MRB
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
D1 < .2500"
D1 > .2500"
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.500 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
UWC
HRC
<55

a General purpose.
BALL
Unit : Inch
TAPER
RADIUS
DS4MRBD1/8R0.008
D3/16R0.015
D1/4R0.008
D1/4R0.020
D3/8R0.020
D3/8R0.040
D1/2R0.015
D1/2R0.030
D1/2R0.060
D5/8R0.020
D5/8R0.040
D3/4R0.030
D3/4R0.060
SOLID END MILLS
I034
Length of
Cut
ap
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
.1250
.1875
.2500
.2500
.3750
.3750
.5000
.5000
.5000
.6250
.6250
.7500
.7500
.008
.015
.008
.020
.020
.040
.015
.030
.060
.020
.040
.030
.060
.375
.563
.750
.750
.875
.875
1.000
1.000
1.000
1.250
1.250
1.500
1.500
1.500
2.000
2.500
2.500
2.500
2.500
3.000
3.000
3.000
3.500
3.500
4.000
4.000
.125
.188
.250
.250
.375
.375
.500
.500
.500
.625
.625
.750
.750
4
4
4
4
4
4
4
4
4
4
4
4
4
Order Number
a
a
a
a
a
a
a
a
a
a
r
r
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
I192
DS2SRB
Ao
Corner radius, Short, 2 ute, For aluminum alloys
aaa
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .188"
.250 < D4 < .375"
D4 = .500"
.750 < D4 < 1.000"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Copper Alloy
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
Unit : Inch
DS2SRBD3/16R0.008A2
D1/4R0.011A2.5
D3/8R0.015A2.5
D3/8R0.015A3
D3/8R0.015A4
D1/2R0.020A3
D1/2R0.020A4
D1/2R0.020A5
D3/4R0.030A4
D3/4R0.030A5
D3/4R0.030A6
D1R0.045A4
D1R0.045A5
D1R0.045A6
.1875
.2500
.3750
.3750
.3750
.5000
.5000
.5000
.7500
.7500
.7500
1.000
1.000
1.000
.008
.011
.015
.015
.015
.020
.020
.020
.030
.030
.030
.045
.045
.045
.250
.313
.500
.500
.500
.625
.625
.625
1.000
1.000
1.000
1.250
1.250
1.250
2.000
2.500
2.500
3.000
4.000
3.000
4.000
5.000
4.000
5.000
6.000
4.000
5.000
6.000
.188
.250
.375
.375
.375
.500
.500
.500
.750
.750
.750
1.000
1.000
1.000
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
r
a
a
r
a
r
r
r
r
r
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I192
RADIUS
Shank
Dia.
D4
TAPER
Overall
Length
L1
SOLID END MILLS
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
Order Number
BALL
a 2 ute radius end mill for aluminum alloys.

a Helix angle 30.
I035
DS2SRB
NAo
Corner radius, Short, 2 ute, Neck relief
aaa
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
0 -.003"
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
D4 = .188"
.250 < D4 < .375"
D4 = .500"
.750 < D4 < 1.000"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Copper Alloy
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
a 2 ute radius end mill with neck relief for aluminum alloys.
a Helix angle 30.
BALL
Unit : Inch
Length of
Cut
ap
Overall
Length
L1
Shank
Dia.
D4
Neck
Length
L3
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
.1875
.2500
.3750
.3750
.3750
.5000
.5000
.5000
.7500
.7500
.7500
1.000
1.000
1.000
.008
.011
.015
.015
.015
.020
.020
.020
.030
.030
.030
.045
.045
.045
.250
.313
.500
.500
.500
.625
.625
.625
1.000
1.000
1.000
1.250
1.250
1.250
2.000
2.500
2.500
3.000
4.000
3.000
4.000
5.000
4.000
5.000
6.000
4.000
5.000
6.000
.188
.250
.375
.375
.375
.500
.500
.500
.750
.750
.750
1.000
1.000
1.000
.563
.750
.875
1.375
2.375
1.125
2.125
3.125
1.875
2.875
3.875
1.625
2.625
3.625
2
2
2
2
2
2
2
2
2
2
2
2
2
2
SOLID END MILLS
TAPER
RADIUS
Order Number
I036
DS2SRBD3/16R0.008NA2
D1/4R0.011NA2.5
D3/8R0.015NA2.5
D3/8R0.015NA3
D3/8R0.015NA4
D1/2R0.020NA3
D1/2R0.020NA4
D1/2R0.020NA5
D3/4R0.030NA4
D3/4R0.030NA5
D3/4R0.030NA6
D1R0.045NA4
D1R0.045NA5
D1R0.045NA6
a
a
a
r
a
a
a
a
r
r
r
r
r
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I192
DS3MHR
A
Roughing, Medium, 3 ute, For aluminum alloys
aaa
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
.250 < D4 < .375"

D4 = .500"
.750 < D4 < 1.000"
0 -.005"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
Unit : Inch
Shank
Dia.
D4
.2500
.3750
.5000
.7500
1.000
.750
.875
1.000
1.500
2.000
2.500
2.500
3.000
4.000
4.000
.250
.375
.500
.750
1.000
3
3
3
3
3
a
a
a
a
TAPER
1
1
1
1
1
SOLID END MILLS
DS3MHRD1/4A
D3/8A
D1/2A
D3/4A
D1A
Type
RADIUS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
BALL
a 3 ute rougher end mill for aluminum alloys.

a Helix angle 45.
CUTTING CONDITIONS
I192
I037
DS3SH
SS
D1 < .2500"
D1 > .2500"
aaa
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
UWC
a 3 ute square end mill for stainless steel.

a Helix angle 45.
BALL
Unit : Inch
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.250
.313
.375
.438
.500
.563
.625
.750
1.000
1.500
2.000
2.000
2.000
2.000
2.500
2.500
3.000
3.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
3
3
3
3
3
3
3
3
3
Order Number
a
a
r
a
r
a
a
r
1
1
1
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
DS3SHD1/8SS
D3/16SS
D1/4SS
D5/16SS
D3/8SS
D7/16SS
D1/2SS
D5/8SS
D3/4SS
Type
I038
CUTTING CONDITIONS
I192
DS3MH
SS
D1 < .2500"
D1 > .2500"
aaa
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
Shank
Dia.
D4
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.375
.563
.750
.813
1.000
1.000
1.250
1.625
1.625
1.500
2.000
2.500
2.500
2.500
2.750
3.000
3.500
4.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
3
3
3
3
3
3
3
3
3
a
a
a
r
a
r
a
a
r
1
1
1
1
1
1
1
1
1
SOLID END MILLS
DS3MHD1/8SS
D3/16SS
D1/4SS
D5/16SS
D3/8SS
D7/16SS
D1/2SS
D5/8SS
D3/4SS
Type
RADIUS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
TAPER
Unit : Inch
BALL

a Helix angle 45.
CUTTING CONDITIONS
I192
I039
DS5MH
SS
D1 < .2500"
D1 > .2500"
aaa
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
.250 < D4 < .375"

.438 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
UWC

a Helix angle 45.
Dia.
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.750
.813
1.000
1.000
1.250
1.625
1.625
2.500
2.500
2.500
2.750
3.000
3.500
4.000
.250
.313
.375
.438
.500
.625
.750
5
5
5
5
5
5
5
Order Number
a
r
a
r
a
a
r
Type
1
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
DS5MHD1/4SS
D5/16SS
D3/8SS
D7/16SS
D1/2SS
D5/8SS
D3/4SS
Stock
BALL
Unit : Inch
I040
CUTTING CONDITIONS
I192
DS5LH
SS
Long, 5 ute, For stainless steel
D1 < .2500"
D1 > .2500"
aaa
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
.250 < D4 < .375"

.438 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.2500
.3125
.3750
.4375
.5000
.6250
.7500
1.250
1.250
1.500
2.000
2.000
2.500
3.250
4.000
4.000
4.000
4.000
4.000
5.000
6.000
.250
.313
.375
.438
.500
.625
.750
5
5
5
5
5
5
5
a
a
a
r
a
a
r
1
1
1
1
1
1
1
TAPER
DS5LHD1/4SS
D5/16SS
D3/8SS
D7/16SS
D1/2SS
D5/8SS
D3/4SS
Type
SOLID END MILLS
Order Number
RADIUS
Unit : Inch
BALL

a Helix angle 45.
CUTTING CONDITIONS
I192
I041
DS3SHB
SS
Ball nose, Short, 3 ute, For stainless steel
D1 < .2500"
D1 > .2500"
aaa
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
UWC
a 3 ute ball nose end mill for stainless steel.
a Helix angle 45.
BALL
Unit : Inch
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.250
.313
.375
.438
.500
.563
.625
.750
1.000
1.500
2.000
2.000
2.000
2.000
2.500
2.500
3.000
3.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
3
3
3
3
3
3
3
3
3
Order Number
a
a
r
a
r
a
a
a
1
1
1
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
DS3SHBD1/8SS
D3/16SS
D1/4SS
D5/16SS
D3/8SS
D7/16SS
D1/2SS
D5/8SS
D3/4SS
Type
I042
CUTTING CONDITIONS
I193
DS3MHB
SS
Ball nose, Medium, 3 ute, For stainless steel
aaa
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < .2500"
D1 > .2500"
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
Shank
Dia.
D4
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.375
.563
.750
.813
1.000
1.000
1.250
1.625
1.625
2.500
2.000
2.500
2.500
2.500
2.750
3.000
3.500
4.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
3
3
3
3
3
3
3
3
3
a
a
a
r
a
r
a
a
a
1
1
1
1
1
1
1
1
1
SOLID END MILLS
DS3MHBD1/8SS
D3/16SS
D1/4SS
D5/16SS
D3/8SS
D7/16SS
D1/2SS
D5/8SS
D3/4SS
Type
RADIUS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
TAPER
Unit : Inch
BALL
a 3 ute ball nose end mill for stainless steel.

a Helix angle 45.
CUTTING CONDITIONS
I193
I043
DS3SHRB
SS
D1 < .2500"
D1 > .2500"
aaa
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
UWC
a 3 ute radius end mill for stainless steel.

a Helix angle 45.
Length of
Cut
ap
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.008
.008
.015
.015
.020
.020
.030
.030
.035
.250
.313
.375
.438
.500
.563
.625
.750
1.000
1.500
2.000
2.000
2.000
2.000
1.500
1.500
3.000
3.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
3
3
3
3
3
3
3
3
3
Order Number
DS3SHRBD1/8R0.008SS
D3/16R0.008SS
D1/4R0.015SS
D5/16R0.015SS
D3/8R0.020SS
D7/16R0.020SS
D1/2R0.030SS
D5/8R0.030SS
D3/4R0.035SS
a
a
r
a
r
a
a
a
Type
1
1
1
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
BALL
Unit : Inch
I044
CUTTING CONDITIONS
I192
DS3MHRB
SS
aaa
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < .2500"
D1 > .2500"
D4 = .125"
D4 = .188"
.250 < D4 < .375"
.438 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
Overall
Length
L1
Shank
Dia.
D4
.1250
.1875
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.008
.008
.015
.015
.020
.020
.030
.030
.035
.375
.563
.750
.813
1.000
1.000
1.250
1.625
1.625
1.500
2.000
2.500
2.500
2.500
2.750
3.000
3.500
4.000
.125
.188
.250
.313
.375
.438
.500
.625
.750
3
3
3
3
3
3
3
3
3
a
a
a
r
a
r
a
a
r
1
1
1
1
1
1
1
1
1
SOLID END MILLS
DS3MHRBD1/8R0.008SS
D3/16R0.008SS
D1/4R0.015SS
D5/16R0.015SS
D3/8R0.020SS
D7/16R0.020SS
D1/2R0.030SS
D5/8R0.030SS
D3/4R0.035SS
Type
RADIUS
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
Order Number
TAPER
Unit : Inch
BALL

a Helix angle 45.
CUTTING CONDITIONS
I192
I045
DS5SHRB
SS
D1 < .2500"
D1 > .2500"
aaa
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
.250 < D4 < .375"

.438 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
SQUARE
Type 1
UWC
a Helix angle 45.
Length of
Cut
ap
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Corner
Radius
R
DS5SHRBD1/4R0.015SS
D5/16R0.015SS
D3/8R0.020SS
D7/16R0.020SS
D1/2R0.030SS
D5/8R0.030SS
D3/4R0.035SS
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.015
.015
.020
.020
.030
.030
.035
.375
.438
.500
.563
.625
.750
1.000
2.000
2.000
2.000
2.500
2.500
3.000
3.000
.250
.313
.375
.438
.500
.625
.750
5
5
5
5
5
5
5
Stock
Dia.
Order Number
a
r
a
r
a
a
r
Type
1
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
BALL
Unit : Inch
I046
CUTTING CONDITIONS
I192
DS5MHRB
SS
aaa
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < .2500"
D1 > .2500"
.250 < D4 < .375"

.438 < D4 < .625"
D4 = .750"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00035"
0 -.00043"
0 -.00051"
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
Length of
Cut
ap
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.015
.015
.020
.020
.030
.030
.035
.750
.813
1.000
1.000
1.250
1.625
1.625
2.500
2.500
2.500
2.750
3.000
3.500
4.000
.250
.313
.375
.438
.500
.625
.750
5
5
5
5
5
5
5
a
a
a
r
a
a
a
1
1
1
1
1
1
1
TAPER
DS5MHRBD1/4R0.015SS
D5/16R0.015SS
D3/8R0.020SS
D7/16R0.020SS
D1/2R0.030SS
D5/8R0.030SS
D3/4R0.035SS
Type
SOLID END MILLS
Order Number
RADIUS
Unit : Inch
BALL

a Helix angle 45.
CUTTING CONDITIONS
I192
I047
DS3MHHRB
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < .2500"
D1 > .2500"
D4 = .125"
.250 < D4 < .375"
.500 < D4 < .625"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00035"
0 -.00043"
Aluminum Alloy
SQUARE
Type 1
UWC
HRC
<55
a 3 ute high helix radius end mill.

a Suitable for difcult-to-cut material.
Length of
Cut
ap
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Corner
Radius
R
Stock
BALL
Unit : Inch
.1250
.2500
.2500
.3750
.3750
.5000
.5000
.5000
.6250
.6250
.008
.015
.030
.020
.040
.015
.030
.060
.030
.060
.375
.750
.750
.875
.875
1.000
1.000
1.000
1.250
1.250
1.500
2.500
2.500
2.500
2.500
3.000
3.000
3.000
3.500
3.500
.125
.250
.250
.375
.375
.500
.500
.500
.625
.625
3
3
3
3
3
3
3
3
3
3
Dia.
Order Number
a
a
a
a
a
a
a
a
a
1
1
1
1
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
DS3MHHRBD1/8R0.008
D1/4R0.015
D1/4R0.030
D3/8R0.020
D3/8R0.040
D1/2R0.015
D1/2R0.030
D1/2R0.060
D5/8R0.030
D5/8R0.060
Type
I048
CUTTING CONDITIONS
I192
DS6MHHRB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < .2500"
D1 > .2500"
D4 = .125"
.250 < D4 < .375"
.500 < D4 < .625"
0 -.002"
0 -.003"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 -.00024"
0 -.00035"
0 -.00043"
Aluminum Alloy
CARBIDE
UWC
SQUARE
Type 1
HRC
<55
Shank
Dia.
D4
.1250
.2500
.2500
.3750
.3750
.5000
.5000
.5000
.6250
.6250
.008
.015
.030
.020
.040
.015
.030
.060
.030
.060
.375
.750
.750
.875
.875
1.000
1.000
1.000
1.250
1.250
1.500
2.500
2.500
2.500
2.500
3.000
3.000
3.000
3.500
3.500
.125
.250
.250
.375
.375
.500
.500
.500
.625
.625
6
6
6
6
6
6
6
6
6
6
a
a
a
a
a
a
a
a
a
a
1
1
1
1
1
1
1
1
1
1
SOLID END MILLS
DS6MHHRBD1/8R0.008
D1/4R0.015
D1/4R0.030
D3/8R0.020
D3/8R0.040
D1/2R0.015
D1/2R0.030
D1/2R0.060
D5/8R0.030
D5/8R0.060
Type
RADIUS
Overall
Length
L1
Dia.
Order Number
TAPER
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
Stock
Unit : Inch
BALL
a 6 ute high helix radius end mill.

a Suitable for difcult-to-cut material.
CUTTING CONDITIONS
I192
I049
MSTAR END MILLS
MS2SS
End mill, Short cut length, 2 ute
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
D1 = 0.1
D1 > 0.1
Hardened Steel
(>55HRC)
0 -0.010
0 -0.020
h6
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
8 < D4 < 10
D4 = 12
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
(10 for 0.1)
SQUARE
Type 1
UWC
Type 2
a 2 ute end mill for general use.
BALL
Unit : mm
TAPER
RADIUS
MS2SSD0010
D0020
D0030
D0040
D0050
D0060
D0070
D0080
D0090
D0100
D0120
D0150
D0180
D0200
D0250
D0300
D0400
D0500
D0600
D0700
D0800
D0900
D1000
D1100
D1200
SOLID END MILLS
I050
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.2
1.5
1.8
2
2.5
3
4
5
6
7
8
9
10
11
12
0.15
0.3
0.45
0.6
0.75
0.9
1.1
1.2
1.4
1.5
1.8
2.3
2.7
3
3.8
4.5
6
7.5
9
10.5
12
13.5
15
16.5
18
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
50
50
50
60
60
70
70
75
75
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
8
8
10
10
12
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
2
1
2
I194
MS2MS
End mill, Medium cut length, 2 ute
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
D1 < 12
D1 > 12
Hardened Steel
(>55HRC)
0 -0.020
0 -0.030
4 < D4 < 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
h6
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
Type 2
UWC
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
3.8
4
4.2
4.4
4.6
4.8
5
5.2
5.4
5.6
5.8
6
6.2
6.4
6.6
6.8
7
7.2
7.4
7.6
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
45
45
45
45
45
45
45
45
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I194
RADIUS
Shank
Dia.
D4
TAPER
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
SOLID END MILLS
Unit : mm
BALL
Type 3
MS2MSD0020
D0030
D0040
D0050
D0060
D0070
D0080
D0090
D0100
D0110
D0120
D0130
D0140
D0150
D0160
D0170
D0180
D0190
D0200
D0210
D0220
D0230
D0240
D0250
D0260
D0270
D0280
D0290
D0300
D0310
D0320
D0330
D0340
D0350
D0360
D0370
D0380
SQUARE
Type 1
I051
MSTAR END MILLS
MS2MS
Unit : mm
Shank
Dia.
D4
3.9
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
16
18
20
7.8
8
8.2
8.4
8.6
8.8
9
9.2
9.4
9.6
9.8
10
10.2
10.4
10.6
10.8
11
11.2
11.4
11.6
11.8
12
13
14
15
16
17
18
19
20
22
24
32
36
40
45
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
70
70
70
70
75
75
90
90
100
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
16
16
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
TAPER
RADIUS
BALL
SQUARE
MS2MSD0390
D0400
D0410
D0420
D0430
D0440
D0450
D0460
D0470
D0480
D0490
D0500
D0510
D0520
D0530
D0540
D0550
D0560
D0570
D0580
D0590
D0600
D0650
D0700
D0750
D0800
D0850
D0900
D0950
D1000
D1100
D1200
D1600
D1800
D2000
SOLID END MILLS
I052
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
CARBIDE
a
s
s
s
s
s
s
s
s
s
a
s
s
s
s
s
s
s
s
s
a
s
s
s
a
s
s
s
a
s
a
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
2
3
2
I194
MS2MD
End mill, Medium cut length, 2 ute, Strong geometry type
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
0 -0.020
h6
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
8 < D4 < 10
D4 = 12
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
CARBIDE
Type 2
UWC
SQUARE
Type 1
a Strong edge type, 2 ute end mill with high resistance to
1
1.5
2
2.5
3
4
5
6
8
10
12
2.5
3.8
5
6.3
7.5
10
12.5
15
20
25
30
Shank
Dia.
D4
No. of
Flutes
40
40
40
40
50
50
50
50
60
70
90
4
4
4
4
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
2
2
2
2
RADIUS
MS2MDD0100
D0150
D0200
D0250
D0300
D0400
D0500
D0600
D0800
D1000
D1200
Overall
Length
L1
TAPER
D1
Length of
Cut
ap
SOLID END MILLS
Dia.
Order Number
Stock
Unit : mm
BALL
corner fracturing.
CUTTING CONDITIONS
I195
I053
MSTAR END MILLS
MS2JS
End mill, Semi long cut length, 2 ute
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
D1 = 0.1
D1 > 0.1
Hardened Steel
(>55HRC)
0 -0.010
0 -0.020
h6
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
8 < D4 < 10
D4 = 12
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
(10 for 0.1)
SQUARE
Type 1
Type 2
UWC
BALL
Unit : mm
TAPER
RADIUS
MS2JSD0010
D0020
D0030
D0040
D0050
D0060
D0070
D0080
D0090
D0100
D0120
D0150
D0180
D0200
D0250
D0300
D0400
D0500
D0600
D0800
D1000
D1200
SOLID END MILLS
I054
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.2
1.5
1.8
2
2.5
3
4
5
6
8
10
12
0.3
0.6
0.9
1.2
1.5
1.8
2.1
2.4
2.7
3
3.6
4.5
5.4
6
7.5
9
12
15
18
24
30
36
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
50
50
50
70
90
90
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
I196
MS2LS
End mill, long cut length, 2 ute
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
0 -0.020
Hardened Steel
(>55HRC)
h6
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
8 < D4 < 10
D4 = 12
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
CARBIDE
Type 2
UWC
SQUARE
Type 1
MS2LSD0020
D0030
D0040
D0050
D0060
D0070
D0080
D0090
D0100
D0150
D0200
D0250
D0300
D0400
D0500
D0600
D0800
D1000
D1200
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
2
2.5
3
4
5
6
8
10
12
0.8
1.2
1.6
2
2.4
2.8
3.2
3.6
4
6
8
10
12
16
20
24
32
40
48
40
40
40
40
40
40
40
40
40
40
40
50
50
50
60
60
70
90
110
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
I197
RADIUS
Shank
Dia.
D4
TAPER
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
SOLID END MILLS
Unit : mm
BALL
I055
MSTAR END MILLS
MS2XL
End mill, Short cut length, 2 ute, Long neck
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
D1 < 0.5
D1 > 0.5
Hardened Steel
(>55HRC)
0 -0.010
0 -0.020
Austenitic
Stainless Steel
Titanium Alloy
h6
4 < D4 < 6
Copper Alloy
0 - 0.008
Aluminum Alloy
SQUARE
Type 1
UWC
Type 2
a 2 ute long neck end mill.
BALL
Unit : mm
TAPER
RADIUS
MS2XLD0020N005
D0020N010
D0020N015
D0030N010
D0030N020
D0030N030
D0030N060
D0030N090
D0040N020
D0040N030
D0040N040
D0040N080
D0040N120
D0050N020
D0050N040
D0050N060
D0050N080
D0050N100
D0050N150
D0060N020
D0060N040
D0060N060
D0060N080
D0060N100
D0060N120
D0060N180
D0070N020
D0070N040
D0070N060
D0070N080
D0070N100
D0080N040
D0080N060
D0080N080
D0080N100
D0080N120
D0080N160
SOLID END MILLS
I056
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.7
0.8
0.8
0.8
0.8
0.8
0.8
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.7
0.7
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
0.5
1
1.5
1
2
3
6
9
2
3
4
8
12
2
4
6
8
10
15
2
4
6
8
10
12
18
2
4
6
8
10
4
6
8
10
12
16
0.18
0.18
0.18
0.28
0.28
0.28
0.28
0.28
0.37
0.37
0.37
0.37
0.37
0.46
0.46
0.46
0.46
0.46
0.46
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.66
0.66
0.66
0.66
0.66
0.76
0.76
0.76
0.76
0.76
0.76
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
50
50
50
45
45
45
50
50
50
50
45
45
45
50
50
45
45
50
50
50
50
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
s
s
s
s
s
s
s
s
s
s
s
s
s
a
a
a
a
a
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Unit : mm
0.8
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
1.2
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.8
1.8
1.8
1.8
1.8
1.8
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3.7
3.7
3.7
3.7
3.7
24
6
8
10
15
4
6
8
10
12
16
20
25
30
6
8
10
12
16
20
6
8
10
12
14
16
18
20
25
30
38
45
6
8
10
12
14
16
18
20
25
30
35
40
50
60
8
12
16
20
25
0.76
0.86
0.86
0.86
0.86
0.95
0.95
0.95
0.95
0.95
0.95
0.95
0.95
0.95
1.15
1.15
1.15
1.15
1.15
1.15
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
2.4
2.4
2.4
2.4
2.4
60
45
50
50
60
50
50
50
50
50
60
60
70
70
50
50
50
50
60
60
50
50
50
50
60
60
60
60
70
70
80
80
50
50
50
50
60
60
60
60
70
70
80
90
100
110
50
50
60
60
70
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
a
a
a
a
a
a
a
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
a
s
a
a
s
a
a
a
s
s
s
s
s
a
a
a
a
CUTTING CONDITIONS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I198
CARBIDE
SQUARE
MS2XLD0080N240
D0090N060
D0090N080
D0090N100
D0090N150
D0100N040
D0100N060
D0100N080
D0100N100
D0100N120
D0100N160
D0100N200
D0100N250
D0100N300
D0120N060
D0120N080
D0120N100
D0120N120
D0120N160
D0120N200
D0150N060
D0150N080
D0150N100
D0150N120
D0150N140
D0150N160
D0150N180
D0150N200
D0150N250
D0150N300
D0150N380
D0150N450
D0200N060
D0200N080
D0200N100
D0200N120
D0200N140
D0200N160
D0200N180
D0200N200
D0200N250
D0200N300
D0200N350
D0200N400
D0200N500
D0200N600
D0250N080
D0250N120
D0250N160
D0250N200
D0250N250
Type
BALL
Shank
Dia.
D4
RADIUS
Overall
Length
L1
TAPER
Neck
Dia.
D5
SOLID END MILLS
Neck
Length
L3
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
I057
MSTAR END MILLS
MS2XL
Dia.
CARBIDE
TAPER
RADIUS
BALL
SQUARE
MS2XLD0250N300
D0250N400
D0250N500
D0300N080
D0300N120
D0300N160
D0300N200
D0300N250
D0300N300
D0300N400
D0300N500
D0400N120
D0400N160
D0400N200
D0400N250
D0400N300
D0400N350
D0400N400
D0400N450
D0400N500
D0400N600
D0500N160
D0500N250
D0500N350
D0500N500
D0500N600
D0600N200
D0600N300
D0600N400
D0600N500
D0600N600
SOLID END MILLS
I058
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
2.5
2.5
2.5
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
6
6
6
6
6
3.7
3.7
3.7
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
6
6
6
6
6
6
6
6
6
6
7.5
7.5
7.5
7.5
7.5
9
9
9
9
9
30
40
50
8
12
16
20
25
30
40
50
12
16
20
25
30
35
40
45
50
60
16
25
35
50
60
20
30
40
50
60
2.4
2.4
2.4
2.85
2.85
2.85
2.85
2.85
2.85
2.85
2.85
3.8
3.8
3.8
3.8
3.8
3.8
3.8
3.8
3.8
3.8
4.8
4.8
4.8
4.8
4.8
5.8
5.8
5.8
5.8
5.8
70
90
100
50
50
60
60
70
70
90
100
50
60
60
70
70
80
90
90
100
110
60
70
80
110
120
80
90
100
110
120
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
Stock
Unit : mm
s
s
s
s
a
a
a
a
a
s
s
s
s
s
s
s
s
s
s
s
a
a
a
a
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
I198
MS2XL6
End mill, Short cut length, 2 ute, 6mm shank
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
0 -0.020
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
h6
D4 = 6
Copper Alloy
0 - 0.008
Aluminum Alloy
CARBIDE
UWC
Type 2
SQUARE
Type 1
Overall
Length
L1
Shank
Dia.
D4
MS2XL6D0030N008
D0030N015
D0040N010
D0040N020
D0050N013
D0050N025
D0060N015
D0060N030
D0070N018
D0070N035
D0080N020
D0080N040
D0090N023
D0090N045
D0100N025
D0100N050
D0110N028
D0110N055
D0120N030
D0120N060
D0130N033
D0130N065
D0140N035
D0140N070
D0150N038
D0150N075
D0160N040
D0160N080
D0170N043
D0170N085
D0180N045
D0180N090
D0190N048
D0190N095
D0200N050
D0200N100
D0210N053
0.3
0.3
0.4
0.4
0.5
0.5
0.6
0.6
0.7
0.7
0.8
0.8
0.9
0.9
1
1
1.1
1.1
1.2
1.2
1.3
1.3
1.4
1.4
1.5
1.5
1.6
1.6
1.7
1.7
1.8
1.8
1.9
1.9
2
2
2.1
0.8
0.5
0.6
0.6
0.8
0.8
0.9
0.9
1.1
1.1
1.2
1.2
1.4
1.4
1.5
1.5
1.7
1.7
1.8
1.8
2
2
2.1
2.1
2.3
2.3
2.4
2.4
2.6
2.6
2.7
2.7
2.9
2.9
3
3
3.2

1.5
1
2
1.3
2.5
1.5
3
1.8
3.5
2
4
2.3
4.5
2.5
5
2.8
5.5
3
6
3.3
6.5
3.5
7
3.8
7.5
4
8
4.3
8.5
4.5
9
4.8
9.5
5
10
5.3

0.27
0.36
0.36
0.46
0.46
0.56
0.56
0.66
0.66
0.76
0.76
0.86
0.86
0.94
0.94
1.04
1.04
1.14
1.14
1.24
1.24
1.34
1.34
1.44
1.44
1.54
1.54
1.64
1.64
1.74
1.74
1.84
1.84
1.90
1.90
2.00
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I199
RADIUS
Neck
Dia.
D5
TAPER
Neck
Length
L3
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
SOLID END MILLS
Unit : mm
BALL

a & 6 shank type.
I059
MSTAR END MILLS
MS2XL6
Unit : mm
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
CARBIDE
2.1
2.2
2.2
2.3
2.3
2.4
2.4
2.5
2.5
3.2
3.3
3.3
3.5
3.5
3.6
3.6
3.8
3.8
10.5
5.5
11
5.8
11.5
6
12
6.3
12.5
2.00
2.10
2.10
2.20
2.20
2.30
2.30
2.40
2.40
60
50
60
50
60
50
60
50
60
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
Order Number
a
a
a
a
a
a
a
a
1
1
1
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
MS2XL6D0210N105
D0220N055
D0220N110
D0230N058
D0230N115
D0240N060
D0240N120
D0250N063
D0250N125
Type
I060
CUTTING CONDITIONS
I199
MS2XL
Square, 2 ute, Long neck
- Inch sizes
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
0 -.0008"
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
D4 = .1250"
D4 = .1875"
D4 = .2500"
h6
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
Aluminum Alloy
CARBIDE
UWC
Type 2
SQUARE
Type 1
Shank
Dia.
D4
MS2XLD1/64N0094
D1/64N0125
D1/64N0187
D1/32N0187
D1/32N0250
D1/32N0375
D1/16N0375
D1/16N0500
D1/16N0750
D3/32N0562
D3/32N0750
D3/32N1125
D1/8N0750
D3/16N1125
D1/4N1500
.0156
.0156
.0156
.0313
.0313
.0313
.0625
.0625
.0625
.0938
.0938
.0938
.1250
.1875
.2500
.0156
.0156
.0156
.0313
.0313
.0313
.0625
.0625
.0625
.0938
.0938
.0938
.1250
.1875
.2500
.0938
.1250
.1875
.1875
.2500
.3750
.3750
.5000
.7500
.5625
.7500
1.1250
.7500
1.1250
1.5000
.0144
.0144
.0144
.0301
.0301
.0301
.0601
.0601
.0601
.0898
.0898
.0898
.1211
.1836
.2441
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.5
2.0
2.5
3.0
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1875
.2500
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
I201
RADIUS
Overall
Length
L1
TAPER
Neck
Dia.
D5
Dia.
Order Number
SOLID END MILLS
Neck
Length
L3
No. of
Flutes
D1
Length of
Cut
ap
Stock
Unit : inch
BALL
a 2 ute, long neck, square end mill for general purpose.
I061
MSTAR END MILLS
MSSHD
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
D1 < 12
D1 > 12
Hardened Steel
(>55HRC)
0 -0.020
0 -0.030
h6
Austenitic
Stainless Steel
Titanium Alloy
D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
SQUARE
Type 1
Type 2
UWC
Type 3
I062
Unit : mm
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
SOLID END MILLS
TAPER
RADIUS
BALL
a 4 ute high power end mill.
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
13
14
15
16
17
18
19
20
4.5
5.3
6
6.8
7.5
8.3
9
9.8
10.5
11.3
12
12.8
13.5
14.3
15
16.5
18
19.5
21
22.5
24
25.5
27
28.5
30
45
45
45
45
50
50
50
60
60
60
60
70
70
70
70
75
75
75
90
90
90
100
100
110
110
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
16
16
16
16
16
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Dia.
Order Number
MSSHDD0300
D0350
D0400
D0450
D0500
D0550
D0600
D0650
D0700
D0750
D0800
D0850
D0900
D0950
D1000
D1100
D1200
D1300
D1400
D1500
D1600
D1700
D1800
D1900
D2000
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
3
1
1
2
3
3
1
2
I203
MSMHD
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
D1 < 12
D1 > 12
Hardened Steel
(>55HRC)
0 -0.020
0 -0.030
4 < D4 < 6
8 < D4 < 10
12 < D4 < 16
20 < D4 < 25
h6
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
Type 2
UWC
4
5
5
5
5
5
6
6
6
6
8
8
8
8
8
8
11
11
11
11
11
12
12
12
12
12
13
13
13
13
13
13
13
13
13
13
13
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I203
RADIUS
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5
5.1
5.2
5.3
5.4
5.5
5.6
Type
TAPER
Shank
Dia.
D4
Dia.
Order Number
SOLID END MILLS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Unit : mm
BALL
Type 3
MSMHDD0200
D0210
D0220
D0230
D0240
D0250
D0260
D0270
D0280
D0290
D0300
D0310
D0320
D0330
D0340
D0350
D0360
D0370
D0380
D0390
D0400
D0410
D0420
D0430
D0440
D0450
D0460
D0470
D0480
D0490
D0500
D0510
D0520
D0530
D0540
D0550
D0560
SQUARE
Type 1
I063
MSTAR END MILLS
MSMHD
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
5.7
5.8
5.9
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
12
13
14
15
16
17
18
19
20
22
25
13
13
13
13
16
19
19
19
19
22
22
22
26
26
26
26
30
35
35
35
40
40
45
50
55
50
50
50
50
60
60
60
60
70
70
70
70
75
75
75
75
90
90
90
100
100
110
110
125
125
6
6
6
6
8
8
8
8
10
10
10
10
12
10
12
12
16
16
16
16
16
20
20
20
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Dia.
Order Number
MSMHDD0570
D0580
D0590
D0600
D0650
D0700
D0750
D0800
D0850
D0900
D0950
D1000
D1100
D1200S10
D1200
D1300
D1400
D1500
D1600
D1700
D1800
D1900
D2000
D2200
D2500
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
2
1
1
1
2
1
1
1
2
1
3
2
3
1
1
2
3
3
1
2
3
2
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
Stock
Unit : mm
I064
CUTTING CONDITIONS
I203
MSJHD
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
D1 < 12
D1 > 12
Hardened Steel
(>55HRC)
0 -0.020
0 -0.030
D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
h6
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
UWC
Type 2
SQUARE
Type 1
2
2.5
3
3.5
4
4.5
5
6
7
8
9
10
11
12
14
15
16
20
8
10
12
14
16
18
20
24
25
28
32
35
35
36
42
45
48
55
60
60
60
60
60
60
60
60
80
80
90
90
100
100
110
110
125
140
6
6
6
6
6
6
6
6
8
8
10
10
12
12
16
16
16
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
1
1
1
1
1
1
1
2
1
2
1
2
1
2
1
1
2
2
I204
RADIUS
MSJHDD0200
D0250
D0300
D0350
D0400
D0450
D0500
D0600
D0700
D0800
D0900
D1000
D1100
D1200
D1400
D1500
D1600
D2000
Type
TAPER
Shank
Dia.
D4
Dia.
Order Number
SOLID END MILLS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Unit : mm
BALL
I065
MSTAR END MILLS
MSMHZD
End mill, Medium cut length, 3 ute for drilling and slotting
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < 12
D1 > 12
0 -0.020
0 -0.030
h6
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
SQUARE
Type 1
Type 2
UWC
Type 3
a 3 ute end mill for both drilling and slotting.
Shank
Dia.
D4
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
13
14
15
16
20
2
3
4
5
6
8
8
10
10
13
13
16
16
16
19
19
19
19
22
22
26
26
26
26
30
32
45
45
50
50
50
50
50
50
50
50
60
60
60
60
70
70
70
70
80
80
90
90
90
110
110
140
4
4
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
16
16
20
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
Dia.
Order Number
TAPER
RADIUS
MSMHZDD0100
D0150
D0200
D0250
D0300
D0350
D0400
D0450
D0500
D0550
D0600
D0650
D0700
D0750
D0800
D0850
D0900
D0950
D1000
D1100
D1200
D1300
D1400
D1500
D1600
D2000
SOLID END MILLS
I066
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
BALL
Unit : mm
s
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
3
3
1
2
2
I205
MSMHZD
- Inch sizes
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
.250 < D4 < .375" 0 - .00035"

.500 < D4 < .625" 0 - .00043"
D4 = .750" 0 - .00051"
D1 < .5000" 0 -.0008"

h6
D1 > .5000" 0 -.0012"
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
Aluminum Alloy
CARBIDE
UWC
Type 2
SQUARE
Type 1
.0625
.0781
.0938
.1094
.1250
.1563
.1875
.2188
.2500
.2813
.3125
.3438
.3750
.4060
.4380
.4690
.5000
.5630
.6250
.7500
.125
.156
.188
.250
.313
.313
.406
.406
.625
.625
.750
.750
.750
.875
.875
1.000
1.000
1.000
1.125
1.250
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.500
2.500
2.750
2.750
3.000
3.000
3.000
3.500
3.500
3.500
4.250
5.500
.250
.250
.250
.250
.250
.250
.250
.250
.250
.375
.375
.375
.375
.500
.500
.500
.500
.625
.625
.750
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
1
1
1
1
2
1
1
1
2
1
1
2
2
1
1
2
2
1
2
1
I206
RADIUS
MSMHZDD1/16
D5/64
D3/32
D7/64
D1/8
D5/32
D3/16
D7/32
D1/4
D9/32
D5/16
D11/32
D3/8
D13/32
D7/16
D15/32
D1/2
D9/16
D5/8
D3/4
Type
TAPER
Shank
Dia.
D4
Dia.
Order Number
SOLID END MILLS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Unit : inch
BALL
a 3 ute end mill for both drilling and slotting.
I067
MSTAR END MILLS
MS4SC
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
0 -0.020
Hardened Steel
(>55HRC)
4 < D4 < 6
8 < D4 < 10
D4 = 12
h6
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
D1
15
D4(h6)
Type 1
ap
D1
UWC
Type 2
D4(h6)
SQUARE
L1
ap
L1
BALL
Unit : mm
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
1
1.5
2
2.5
3
4
5
6
8
10
12
1.5
2.3
3
3.8
4.5
6
7.5
9
12
15
18
40
40
40
40
50
50
50
50
60
70
75
4
4
4
4
6
6
6
6
8
10
12
4
4
4
4
4
4
4
4
4
4
4
Order Number
s
s
s
s
s
s
s
s
s
s
1
1
1
1
1
1
1
2
2
2
2
SOLID END MILLS
TAPER
RADIUS
MS4SCD0100
D0150
D0200
D0250
D0300
D0400
D0500
D0600
D0800
D1000
D1200
Type
I068
CUTTING CONDITIONS
I207
Titanium Alloy
Copper Alloy
Aluminum Alloy
CARBIDE
D1
15
ap
Type 3
ap
Shank
Dia.
D4
MS4MCD0100
D0150
D0200
D0250
D0300
D0350
D0400
D0450
D0500
D0550
D0600
D0650
D0700
D0750
D0800
D0850
D0900
D0950
D1000
D1100
D1200
D1400
D1600
D1800
D2000
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
14
16
18
20
2.5
3.8
5
6.3
7.5
9
10
11.5
12.5
14
15
16.5
17.5
19
20
21.5
22.5
24
25
27.5
30
35
40
45
50
40
40
40
40
50
50
50
50
50
50
50
60
60
60
60
70
70
70
70
75
90
90
100
100
110
4
4
4
4
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
16
16
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
s
a
s
a
s
a
s
s
s
a
s
s
s
a
s
a
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
3
2
3
2
I207
RADIUS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
BALL
L1
Unit : mm
Order Number
SQUARE
D1
L1
D1
Type 2
L1
ap
UWC
Type 1
TAPER
Austenitic
Stainless Steel
SOLID END MILLS
Hardened Steel
(>55HRC)
h6
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
D4(h6)
Hardened Steel
( < 55HRC)
4 < D4 < 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
D4(h6)
(<30HRC)
( < 45HRC)
0 -0.020
0 -0.030
D4(h6)
MS4MC
D1 < 12
D1 > 12
I069
MSTAR END MILLS
MS4JC
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
0 -0.020
Hardened Steel
(>55HRC)
h6
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
8 < D4 < 10
D4 = 12
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
D1
15
D4(h6)
Type 1
L1
D1
UWC
Type 2
D4(h6)
SQUARE
ap
ap
L1
BALL
Unit : mm
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
1
1.5
2
2.5
3
4
5
6
8
10
12
4
6
8
10
12
16
20
24
32
40
48
40
40
40
50
50
50
60
60
70
90
110
4
4
4
4
6
6
6
6
8
10
12
4
4
4
4
4
4
4
4
4
4
4
Order Number
a
a
a
a
a
a
a
a
a
a
1
1
1
1
1
1
1
2
2
2
2
SOLID END MILLS
TAPER
RADIUS
MS4JCD0100
D0150
D0200
D0250
D0300
D0400
D0500
D0600
D0800
D1000
D1200
Type
I070
CUTTING CONDITIONS
I208
MS4XL
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
Aluminum Alloy
CARBIDE
D1
15
D5
L1
D1
UWC
D4(h6)
Type 2
ap
L3
L1
Unit : mm
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
1
1
1
1
1
1
1.1
1.1
1.1
1.2
1.2
1.2
1.2
1.2
1.3
1.3
1.3
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.6
1
1
1
1
1
1
1.1
1.1
1.1
1.2
1.2
1.2
1.2
1.2
1.3
1.3
1.3
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.6
4
6
8
10
12
16
6
10
16
6
8
10
12
16
6
12
18
6
8
10
12
14
16
22
6
8
10
12
14
16
18
20
6
8
10
12
14
0.94
0.94
0.94
0.94
0.94
0.94
1.04
1.04
1.04
1.14
1.14
1.14
1.14
1.14
1.24
1.24
1.24
1.34
1.34
1.34
1.34
1.34
1.34
1.34
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.54
1.54
1.54
1.54
1.54
50
50
50
50
50
60
50
50
60
50
50
50
50
60
50
50
60
50
50
50
50
60
60
60
50
50
50
50
60
60
60
60
50
50
50
50
60
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Order Number
MS4XLD0100N040
D0100N060
D0100N080
D0100N100
D0100N120
D0100N160
D0110N060
D0110N100
D0110N160
D0120N060
D0120N080
D0120N100
D0120N120
D0120N160
D0130N060
D0130N120
D0130N180
D0140N060
D0140N080
D0140N100
D0140N120
D0140N140
D0140N160
D0140N220
D0150N060
D0150N080
D0150N100
D0150N120
D0150N140
D0150N160
D0150N180
D0150N200
D0160N060
D0160N080
D0160N100
D0160N120
D0160N140
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I200
BALL
L3
SQUARE
D4(h6)
Type 1
ap
RADIUS
4 < D4 < 6
8 < D4 < 10
TAPER
Hardened Steel
(>55HRC)
D5
Hardened Steel
( < 55HRC)
h6
SOLID END MILLS
(<30HRC)
( < 45HRC)
0 -0.020
I071
MSTAR END MILLS
MS4XL
Unit : mm
I072
Dia.
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
1.6
1.6
1.6
1.6
1.7
1.7
1.7
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.9
1.9
1.9
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3.5
3.5
3.5
4
4
4
4
4
4
4
4
1.6
1.6
1.6
1.6
1.7
1.7
1.7
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.9
1.9
1.9
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3.5
3.5
3.5
4
4
4
4
4
4
4
4
16
18
20
26
6
14
24
6
8
10
12
14
16
18
20
25
6
16
28
6
8
10
12
14
16
18
20
25
30
8
12
16
20
25
8
12
16
20
25
30
15
25
35
12
16
20
25
30
35
40
45
1.54
1.54
1.54
1.54
1.64
1.64
1.64
1.74
1.74
1.74
1.74
1.74
1.74
1.74
1.74
1.74
1.84
1.84
1.84
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.4
2.4
2.4
2.4
2.4
2.9
2.9
2.9
2.9
2.9
2.9
3.4
3.4
3.4
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
60
60
60
70
50
60
70
50
50
50
50
60
60
60
60
70
50
60
70
50
50
50
50
60
60
60
60
70
70
50
50
60
60
70
50
50
60
60
70
70
60
70
80
50
60
60
70
70
80
90
90
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Order Number
MS4XLD0160N160
D0160N180
D0160N200
D0160N260
D0170N060
D0170N140
D0170N240
D0180N060
D0180N080
D0180N100
D0180N120
D0180N140
D0180N160
D0180N180
D0180N200
D0180N250
D0190N060
D0190N160
D0190N280
D0200N060
D0200N080
D0200N100
D0200N120
D0200N140
D0200N160
D0200N180
D0200N200
D0200N250
D0200N300
D0250N080
D0250N120
D0250N160
D0250N200
D0250N250
D0300N080
D0300N120
D0300N160
D0300N200
D0300N250
D0300N300
D0350N150
D0350N250
D0350N350
D0400N120
D0400N160
D0400N200
D0400N250
D0400N300
D0400N350
D0400N400
D0400N450
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Unit : mm
Overall
Length
L1
Shank
Dia.
D4
4
5
5
5
5
6
6
6
6
8
8
8
10
10
10
4
5
5
5
5
6
6
6
6
8
8
8
10
10
10
50
16
25
35
50
20
30
40
50
30
50
70
40
60
80
3.9
4.9
4.9
4.9
4.9
5.85
5.85
5.85
5.85
7.85
7.85
7.85
9.7
9.7
9.7
100
60
70
80
110
80
90
100
110
90
110
130
100
120
140
6
6
6
6
6
6
6
6
6
8
8
8
10
10
10
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
s
s
TAPER
RADIUS
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
CARBIDE
SOLID END MILLS
MS4XLD0400N500
D0500N160
D0500N250
D0500N350
D0500N500
D0600N200
D0600N300
D0600N400
D0600N500
D0800N300
D0800N500
D0800N700
D1000N400
D1000N600
D1000N800
Type
SQUARE
Neck
Dia.
D5
BALL
Neck
Length
L3
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
CUTTING CONDITIONS
I200
I073
MSTAR END MILLS
MS4XL
- Inch sizes
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
D4 = .1250"
D4 = .1875"
D4 = .2500"
h6
Copper Alloy
D5
CARBIDE
Hardened Steel
( < 55HRC)
0 -.0008"
0 -.00024"
0 -.00031"
0 -.00035"
Aluminum Alloy
D1
15
D4(h6)
Type 1
ap
L3
D5
D1
UWC
Type 2
D4(h6)
SQUARE
L1
ap
a 4 ute, long neck, square end mill for general purpose.
L3
L1
BALL
Unit : inch
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
.0625
.0625
.0625
.0938
.0938
.0938
.1250
.1875
.2500
.0625
.0625
.0625
.0938
.0938
.0938
.1250
.1875
.2500
.3750
.5000
.7500
.5625
.7500
1.1250
.7500
1.1250
1.5000
.0601
.0601
.0601
.0898
.0898
.0898
.1211
.1836
.2441
2.0
2.0
2.0
2.0
2.0
2.5
2.0
2.5
3.0
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1875
.2500
4
4
4
4
4
4
4
4
4
Order Number
a
a
a
a
a
a
a
a
1
1
1
1
1
1
2
2
2
SOLID END MILLS
TAPER
RADIUS
MS4XLD1/16N0375
D1/16N0500
D1/16N0750
D3/32N0562
D3/32N0750
D3/32N1125
D1/8N0750
D3/16N1125
D1/4N1500
Type
I074
CUTTING CONDITIONS
I202
MS2ES
End mill, 2 ute, For Swiss type lathes
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
0 -0.020
Hardened Steel
(>55HRC)
4 < D4 < 6
7 < D4 < 10
h6
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
Aluminum Alloy
CARBIDE
Type 2
D1
D4(h6)
UWC
ap
Shank
Dia.
D4
3
3.5
4
5
5
6
6
7
8
8
10
10
12
3
3.5
4
5
5
6
6
6
6
6
6
6
6
35
35
35
35
35
35
35
35
35
35
35
35
35
4
4
4
5
6
5
6
7
7
8
7
10
10
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
Overall length 45mm
1
1
2
2
1
3
2
2
3
2
3
2
3
Unit : mm
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
3
3.5
4
5
6
7
8
8
10
10
12
3
3.5
4
5
6
7
8
8
10
10
12
45
45
45
45
45
45
45
45
45
45
45
4
4
4
6
6
7
7
8
7
10
10
2
2
2
2
2
2
2
2
2
2
2
Order Number
MS2ESD0300L45S04
D0350L45S04
D0400L45S04
D0500L45S06
D0600L45S06
D0700L45S07
D0800L45S07
D0800L45S08
D1000L45S07
D1000L45S10
D1200L45S10
Type
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
RADIUS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
TAPER
Unit : mm
BALL
L1
Overall length 35mm
MS2ESD0300L35S04
D0350L35S04
D0400L35S04
D0500L35S05
D0500L35S06
D0600L35S05
D0600L35S06
D0700L35S07
D0800L35S07
D0800L35S08
D1000L35S07
D1000L35S10
D1200L35S10
Type 3
SOLID END MILLS
a 2 ute end mill.
SQUARE
Type 1
1
1
2
1
2
2
3
2
3
2
3
I209
I075
MSTAR END MILLS
MS3ES
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
0 -0.020
Hardened Steel
(>55HRC)
h6
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6 0 - 0.008

7 < D4 < 10 0 - 0.009
Copper Alloy
Aluminum Alloy
SQUARE
Type 1
Type 2
UWC
Type 3
Overall length 35mm
MS3ESD0300L35S04
D0350L35S04
D0400L35S04
D0500L35S05
D0500L35S06
D0600L35S05
D0600L35S06
D0700L35S07
D0800L35S07
D0800L35S08
D1000L35S07
D1000L35S10
D1200L35S10
TAPER
Shank
Dia.
D4
3
3.5
4
5
5
6
6
7
8
8
10
10
12
3
3.5
4
5
5
6
6
6
6
6
6
6
6
35
35
35
35
35
35
35
35
35
35
35
35
35
4
4
4
5
6
5
6
7
7
8
7
10
10
3
3
3
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
a
a
Overall length 45mm

Dia.
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
3
3.5
4
5
6
7
8
8
10
10
12
3
3.5
4
5
6
7
8
8
10
10
12
45
45
45
45
45
45
45
45
45
45
45
4
4
4
6
6
7
7
8
7
10
10
3
3
3
3
3
3
3
3
3
3
3
Order Number
Type
1
1
2
2
1
3
2
2
3
2
3
2
3
Unit : mm
Stock
SOLID END MILLS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
MS3ESD0300L45S04
D0350L45S04
D0400L45S04
D0500L45S06
D0600L45S06
D0700L45S07
D0800L45S07
D0800L45S08
D1000L45S07
D1000L45S10
D1200L45S10
I076
Unit : mm
Order Number
RADIUS
BALL
a 3 ute end mill.
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
1
1
2
1
2
2
3
2
3
2
3
I209
MS4EC
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
D1 < 12
D1 > 12
Hardened Steel
(>55HRC)
0 -0.020
0 -0.030
h6
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
7 < D4 < 10
Copper Alloy
0 - 0.008
0 - 0.009
Aluminum Alloy
CARBIDE
Type 2
UWC
Type 3
SQUARE
Type 1
Shank
Dia.
D4
MS4ECD0300L35S04
D0350L35S04
D0400L35S04
D0500L35S05
D0500L35S06
D0600L35S05
D0600L35S06
D0700L35S07
D0800L35S07
D0800L35S08
D1000L35S07
D1000L35S10
D1200L35S10
3
3.5
4
5
5
6
6
7
8
8
10
10
12
3
3.5
4
5
5
6
6
6
6
6
6
6
6
35
35
35
35
35
35
35
35
35
35
35
35
35
4
4
4
5
6
5
6
7
7
8
7
10
10
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
Overall length 45mm
1
1
2
2
1
3
2
2
3
2
3
2
3
Unit : mm
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
3
3.5
4
5
6
7
8
8
10
10
12
14
3
3.5
4
5
6
7
8
8
10
10
12
14
45
45
45
45
45
45
45
45
45
45
45
45
4
4
4
6
6
7
7
8
7
10
10
10
4
4
4
4
4
4
4
4
4
4
4
4
Order Number
MS4ECD0300L45S04
D0350L45S04
D0400L45S04
D0500L45S06
D0600L45S06
D0700L45S07
D0800L45S07
D0800L45S08
D1000L45S07
D1000L45S10
D1200L45S10
D1400L45S10
Type
a
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
RADIUS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
TAPER
Unit : mm
SOLID END MILLS
Overall length 35mm
BALL
a 4 ute end mill.
1
1
2
1
2
2
3
2
3
2
3
3
I209
I077
MSTAR END MILLS
MS2SB
Ball nose end mill, Short cut length, 2 ute
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
0 -0.020
e0.01
h6
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
8 < D4 < 10
D4 = 12
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
SQUARE
Type 1
Type 2
UWC
a 2 ute ball nose end mill for general use.
Order Number
SOLID END MILLS
TAPER
RADIUS
MS2SBR0010S04
R0010S06
R0015S04
R0015S06
R0020S04
R0020S06
R0025S04
R0025S06
R0030S04
R0030S06
R0035S04
R0040S04
R0040S06
R0045S04
R0050S04
R0050S06
R0060S04
R0060S06
R0070S04
R0070S06
R0075S04
R0075S06
R0080S04
R0080S06
R0090S04
R0090S06
R0100S04
R0100S06
R0125S04
R0125S06
R0150S06
R0200S06
R0250S06
R0300S06
R0400S08
R0500S10
R0600S12
I078
Radius of
Ball Nose
R
Dia.
0.1
0.1
0.15
0.15
0.2
0.2
0.25
0.25
0.3
0.3
0.35
0.4
0.4
0.45
0.5
0.5
0.6
0.6
0.7
0.7
0.75
0.75
0.8
0.8
0.9
0.9
1
1
1.25
1.25
1.5
2
2.5
3
4
5
6
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
BALL
Unit : mm
0.2
0.2
0.3
0.3
0.4
0.4
0.5
0.5
0.6
0.6
0.7
0.8
0.8
0.9
1
1
1.2
1.2
1.4
1.4
1.5
1.5
1.6
1.6
1.8
1.8
2
2
2.5
2.5
3
4
5
6
8
10
12
0.3
0.3
0.5
0.5
0.6
0.6
0.8
0.8
0.9
0.9
1.1
1.2
1.2
1.4
1.5
1.5
1.8
1.8
2.1
2.1
2.3
2.3
2.4
2.4
2.7
2.7
3
3
3.8
3.8
4.5
6
7.5
9
12
15
18
45
50
45
50
45
50
45
50
45
50
45
45
50
45
45
50
45
50
45
50
45
50
45
50
45
50
50
50
50
50
70
70
80
80
90
100
110
4
6
4
6
4
6
4
6
4
6
4
4
6
4
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
I210
MS2MB
Ball nose end mill, Medium cut length, 2 ute
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
e0.01
0 -0.020
h6
Austenitic
Stainless Steel
Titanium Alloy
D4 = 3
4 < D4 < 6
8 < D4 < 10
D4 = 12
Copper Alloy
0
0
0
0

- 0.006
- 0.008
- 0.009
- 0.011
Aluminum Alloy
CARBIDE
Type 2
UWC
SQUARE
Type 1
0.25
0.3
0.4
0.5
0.6
0.7
0.75
0.8
0.9
1
1.25
1.5
1.5
1.75
2
2
2.5
3
4
5
6
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
0.5
0.6
0.8
1
1.2
1.4
1.5
1.6
1.8
2
2.5
3
3
3.5
4
4
5
6
8
10
12
1
1.2
1.6
2.5
2.5
3
4
4
5
6
6
8
8
8
8
8
12
12
14
18
22
45
45
45
45
45
45
45
45
45
50
50
70
70
70
70
70
80
80
90
100
110
4
4
4
4
4
4
4
4
4
4
4
3
6
6
4
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
s
a
a
s
a
a
a
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
2
2
2
2
I210
RADIUS
Dia.
TAPER
MS2MBR0025
R0030
R0040
R0050
R0060
R0070
R0075
R0080
R0090
R0100
R0125
R0150S03
R0150
R0175
R0200S04
R0200
R0250
R0300
R0400
R0500
R0600
Radius of
Ball Nose
R
Stock
Order Number
SOLID END MILLS
Unit : mm
BALL
a 2 ute ball nose end mill for general use.
I079
MSTAR END MILLS
MS2XLB
Ball nose end mill, Short cut length, 2 ute, Long neck
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
0 -0.020
e0.01
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
h6
4 < D4 < 6
Copper Alloy
0 - 0.008
Aluminum Alloy
Type 1
Effective
length
SQUARE
Effective length
for inclined angle
UWC
Type 2
a 2 ute long neck ball nose end mill.

Inclined angle
SOLID END MILLS
TAPER
RADIUS
I080
Order Number
MS2XLBR0010N005
R0010N005S06
R0010N008S06
R0010N010
R0010N010S06
R0010N013
R0010N013S06
R0010N015
R0010N015S06
R0010N018
R0010N018S06
R0010N020
R0010N020S06
R0010N025
R0010N030
R0015N008S06
R0015N010
R0015N010S06
R0015N012S06
R0015N015
R0015N015S06
R0015N020
R0015N020S06
R0015N025
R0015N030
R0015N040
R0020N010
R0020N010S06
R0020N012S06
R0020N015
R0020N015S06
R0020N020
R0020N020S06
R0020N025
R0020N025S06
R0020N030
R0020N030S06
Radius of Dia. Length of Neck Neck Cutting Edge to Overall Shank No. of
Cut Length Dia. Shank Angle Length Dia. Flutes
Ball Nose
D1
D4
ap
L3
L1
D5
B2
R
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.8
1
1
1.25
1.25
1.5
1.5
1.75
1.75
2
2
2.5
3
0.8
1
1
1.2
1.5
1.5
2
2
2.5
3
4
1
1
1.2
1.5
1.5
2
2
2.5
2.5
3
3
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
14.1
14.4
14.1
13.3
13.8
12.9
13.6
12.5
13.3
12.2
13.1
11.9
12.8
11.3
10.7
14.1
13.3
13.9
13.7
12.5
13.3
11.9
12.8
11.2
10.7
9.7
13.4
13.9
13.7
12.6
13.4
11.9
12.8
11.2
12.4
10.7
11.9
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
6
6
4
6
4
6
4
6
4
6
4
6
4
4
6
4
6
6
4
6
4
6
4
4
4
4
6
6
4
6
4
6
4
6
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Stock
BALL
Unit : mm
a
a
a
a
s
s
s
a
s
s
s
s
s
s
s
a
a
s
a
s
s
a
s
s
s
s
a
s
a
s
s
a
a
s
s
a
Effective length
for inclined angle
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
30'
0.5
0.5
0.8
1
1
1.3
1.3
1.5
1.5
1.8
1.8
2.1
2.1
2.6
3.1
0.8
1
1
1.2
1.5
1.5
2.1
2.1
2.6
3.1
4.2
1
1
1.2
1.5
1.5
2
2
2.6
2.6
3.1
3.1
0.5
0.5
0.8
1.1
1.1
1.3
1.3
1.6
1.6
1.9
1.9
2.2
2.2
2.7
3.2
0.8
1.1
1.1
1.3
1.6
1.6
2.2
2.2
2.7
3.2
4.3
1
1
1.3
1.6
1.6
2.1
2.1
2.7
2.7
3.2
3.2
0.6
0.6
0.9
1.2
1.2
1.5
1.5
1.7
1.7
2
2
2.3
2.3
2.9
3.5
0.9
1.2
1.2
1.4
1.7
1.7
2.3
2.3
2.9
3.5
4.6
1.1
1.1
1.4
1.7
1.7
2.3
2.3
2.9
2.9
3.4
3.4
0.6
0.6
1
1.3
1.3
1.6
1.6
1.9
1.9
2.2
2.2
2.5
2.5
3.1
3.7
1
1.3
1.3
1.5
1.9
1.9
2.5
2.5
3.1
3.7
5
1.2
1.2
1.5
1.8
1.8
2.5
2.5
3.1
3.1
3.7
3.7
3.5
4
4.5
5
5.5
6
1.5
1.5
2
2
2.5
2.5
3
3
3.5
3.5
4
4
4.5
4.5
5
5
5.5
5.5
6
6
7
7
8
8
10
10
1.8
2
2
2.5
2.5
3
3
3.5
3.5
4
4
4.5
4.5
5
5
6
6
7
8
0.36
0.36
0.36
0.36
0.36
0.36
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
10.2
9.7
9.3
8.9
8.5
8.2
12.6
13.4
11.9
12.9
11.2
12.4
10.6
11.9
10.1
11.5
9.6
11.1
9.2
10.7
8.8
10.4
8.4
10.1
8.1
9.7
7.5
9.2
7
8.7
6.2
7.8
13
11.8
12.8
11.1
12.3
10.5
11.8
10
11.4
9.5
11
9.1
10.6
8.7
10.3
8
9.7
7.4
6.9
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
4
4
4
4
4
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
a
a
s
s
a
s
s
s
s
a
s
s
s
s
s
s
s
a
s
s
s
a
s
a
s
a
a
s
s
s
s
a
s
s
a
s
s
s
s
s
a
s
s
a
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3.6
3.7
4.1
4.3
4.7
4.8
5.2
5.3
5.7
5.9
6.2
6.4
1.5
1.6
1.5
1.6
2
2.1
2
2.1
2.6
2.7
2.6
2.7
3.1
3.2
3.1
3.2
3.6
3.7
3.6
3.7
4.1
4.3
4.1
4.3
4.6
4.8
4.6
4.8
5.2
5.3
5.2
5.3
5.7
5.9
5.7
5.9
6.2
6.4
6.2
6.4
7.2
7.5
7.2
7.5
8.3
8.5
8.3
8.5
10.3 10.7
10.3 10.7
1.9
1.9
2.1
2.2
2.1
2.2
2.6
2.7
2.6
2.7
3.1
3.3
3.1
3.3
3.6
3.8
3.6
3.8
4.2
4.3
4.2
4.3
4.7
4.9
4.7
4.9
5.2
5.4
5.2
5.4
6.3
6.5
6.3
6.5
7.3
7.5
8.3
8.6
CARBIDE
4
4.6
5.2
5.7
6.3
6.9
1.7
1.7
2.3
2.3
2.9
2.9
3.4
3.4
4
4
4.6
4.6
5.2
5.2
5.7
5.7
6.3
6.3
6.9
6.9
8
8
9.2
9.2
11.5
11.5
2.1
2.3
2.3
2.9
2.9
3.5
3.5
4.1
4.1
4.6
4.6
5.2
5.2
5.8
5.8
6.9
6.9
8.1
9.2
4.3
4.9
5.6
6.2
6.8
7.4
1.8
1.8
2.4
2.4
3.1
3.1
3.7
3.7
4.3
4.3
4.9
4.9
5.6
5.6
6.2
6.2
6.8
6.8
7.4
7.4
8.7
8.7
9.9
9.9
12.4
12.4
2.3
2.5
2.5
3.1
3.1
3.8
3.8
4.4
4.4
5
5
5.6
5.6
6.2
6.2
7.5
7.5
8.7
10
CUTTING CONDITIONS
I211
SQUARE
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
BALL
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
30'
RADIUS
0.2
0.2
0.2
0.2
0.2
0.2
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
Effective length
for inclined angle
Type
TAPER
MS2XLBR0020N035
R0020N040
R0020N045
R0020N050
R0020N055
R0020N060
R0025N015
R0025N015S06
R0025N020
R0025N020S06
R0025N025
R0025N025S06
R0025N030
R0025N030S06
R0025N035
R0025N035S06
R0025N040
R0025N040S06
R0025N045
R0025N045S06
R0025N050
R0025N050S06
R0025N055
R0025N055S06
R0025N060
R0025N060S06
R0025N070
R0025N070S06
R0025N080
R0025N080S06
R0025N100
R0025N100S06
R0030N018S06
R0030N020
R0030N020S06
R0030N025
R0030N025S06
R0030N030
R0030N030S06
R0030N035
R0030N035S06
R0030N040
R0030N040S06
R0030N045
R0030N045S06
R0030N050
R0030N050S06
R0030N060
R0030N060S06
R0030N070
R0030N080
Ball Nose
D1
D5
D4
ap
L3
L1
B2
R
SOLID END MILLS
Order Number
Stock
Unit : mm
I081
MSTAR END MILLS
MS2XLB
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
I082
Order Number
MS2XLBR0030N080S06
R0030N090
R0030N100
R0030N100S06
R0030N110
R0030N120
R0040N020
R0040N020S06
R0040N024S06
R0040N030
R0040N030S06
R0040N040
R0040N040S06
R0040N050
R0040N060
R0040N060S06
R0040N070
R0040N080
R0040N080S06
R0040N100
R0040N100S06
R0040N120
R0050N030
R0050N030S06
R0050N040
R0050N040S06
R0050N050
R0050N050S06
R0050N060
R0050N060S06
R0050N070
R0050N080
R0050N080S06
R0050N090
R0050N100
R0050N100S06
R0050N120
R0050N120S06
R0050N140
R0050N160
R0050N160S06
R0050N180
R0050N200
R0050N200S06
R0060N036S06
R0060N060
R0060N060S06
R0060N080
R0060N080S06
R0060N100
R0060N100S06
Ball Nose
D1
D5
D4
ap
L3
L1
B2
R
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
1.2
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
1.2
8
9
10
10
11
12
2
2
2.4
3
3
4
4
5
6
6
7
8
8
10
10
12
3
3
4
4
5
5
6
6
7
8
8
9
10
10
12
12
14
16
16
18
20
20
3.6
6
6
8
8
10
10
0.56
0.56
0.56
0.56
0.56
0.56
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.14
1.14
1.14
1.14
1.14
1.14
1.14
8.6
6.4
6
7.8
5.7
5.4
11.7
12.8
12.4
10.4
11.8
9.4
11
8.5
7.8
9.6
7.2
6.7
8.5
5.9
7.7
5.2
10.1
11.6
9.1
10.8
8.2
10.1
7.5
9.4
6.9
6.4
8.3
6
5.6
7.5
5
6.8
4.5
4.1
5.7
3.7
3.4
5
11.1
7.3
9.3
6.2
8.2
5.4
7.4
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
55
50
55
60
55
55
60
50
50
50
50
50
50
50
6
4
4
6
4
4
4
6
6
4
6
4
6
4
4
6
4
4
6
4
6
4
4
6
4
6
4
6
4
6
4
4
6
4
4
6
4
6
4
4
6
4
4
6
6
4
6
4
6
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Stock
Unit : mm
s
s
a
s
s
s
a
s
a
s
s
a
a
s
a
s
s
a
s
a
s
s
a
a
a
s
s
a
a
s
s
a
s
s
a
s
a
s
a
a
s
a
a
s
a
s
a
a
s
s
s
Effective length
for inclined angle
Type
30'
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
8.3
9.4
10.4
10.4
11.4
12.5
2.1
2.1
2.5
3.1
3.1
4.2
4.2
5.2
6.3
6.3
7.3
8.3
8.3
10.4
10.4
12.5
3.2
3.2
4.2
4.2
5.3
5.3
6.3
6.3
7.4
8.4
8.4
9.5
10.5
10.5
12.6
12.6
14.7
16.8
16.8
18.9
20.9
20.9
3.8
6.3
6.3
8.4
8.4
10.5
10.5
8.6
9.2
9.7 10.4
10.8 11.5
10.8 11.5
11.8 12.7
12.9 13.8
2.2
2.3
2.2
2.3
2.6
2.8
3.3
3.5
3.3
3.5
4.3
4.6
4.3
4.6
5.4
5.8
6.5
6.9
6.5
6.9
7.5
8.1
8.6
9.2
8.6
9.2
10.8 11.5
10.8 11.5
12.9 13.8
3.3
3.6
3.3
3.6
4.4
4.8
4.4
4.8
5.5
6
5.5
6
6.6
7.1
6.6
7.1
7.7
8.3
8.8
9.4
8.8
9.4
9.9 10.6
10.9 11.7
10.9 11.7
13.1 14
13.1 14
15.2 16.3
17.4 18.6
17.4 18.6
19.5 20.9
21.6 23.2
21.6 23.2
4
4.3
6.6
7.1
6.6
7.1
8.8
9.4
8.8
9.4
10.9 11.7
10.9 11.7
10
11.2
12.5
12.5
13.7
15
2.5
2.5
3
3.7
3.7
5
5
6.2
7.5
7.5
8.7
10
10
12.4
12.4
14.9
3.9
3.9
5.2
5.2
6.4
6.4
7.7
7.7
8.9
10.2
10.2
11.4
12.6
12.6
15.1
15.1
17.6
20.1
20.1
22.6
25.1
25.1
4.7
7.6
7.6
10.1
10.1
12.6
12.6
12
12
14
16
16
18
24
8
12
16
4.5
6
6
7.5
8
8
10
10
12
12
14
14
16
16
18
20
20
22
30
8
12
16
20
8
12
16
20
4
4
6
6
8
8
10
10
12
12
14
14
16
16
1.14 4.8
1.14 6.7
1.14 4.3
1.14 3.9
1.14 5.6
1.14 3.5
1.14 2.8
1.34 6
1.34 4.6
1.34 3.7
1.44 10.2
1.44 7
1.44 9.2
1.44 8.3
1.44 5.9
1.44 8.1
1.44 5.1
1.44 7.2
1.44 4.4
1.44 6.5
1.44 4
1.44 5.9
1.44 3.6
1.44 5.4
1.44 3.3
1.44 3
1.44 4.6
1.44 2.8
1.44 2.1
1.54 5.8
1.54 4.3
1.54 3.5
1.54 2.9
1.74 5.5
1.74 4.1
1.74 3.3
1.74 2.7
1.9
8.2
1.9 10.6
1.9
6.4
1.9
9
1.9
5.3
1.9
7.8
1.9
4.5
1.9
6.9
1.9
3.9
1.9
6.1
1.9
3.4
1.9
5.6
1.9
3.1
1.9
5.1
50
55
50
55
60
55
65
50
50
55
50
50
50
50
50
50
50
50
50
55
50
55
55
60
55
55
60
60
70
50
50
55
55
50
50
55
55
50
50
50
50
50
50
50
50
50
55
50
55
55
60
4
6
4
4
6
4
4
4
4
4
6
4
6
6
4
6
4
6
4
6
4
6
4
6
4
4
6
4
4
4
4
4
4
4
4
4
4
4
6
4
6
4
6
4
6
4
6
4
6
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
a
a
a
a
a
s
a
a
s
a
s
a
s
a
s
a
s
a
a
s
s
s
a
a
a
a
a
a
a
a
a
s
a
a
a
s
a
a
a
s
a
s
a
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
12.6
12.6
14.7
16.8
16.8
18.8
25.1
8.4
12.6
16.8
4.7
6.3
6.3
7.9
8.4
8.4
10.5
10.5
12.6
12.6
14.7
14.7
16.8
16.8
18.8
20.9
20.9
23
31.2
8.4
12.6
16.8
20.9
8.4
12.6
16.8
20.9
4.1
4.1
6.2
6.2
8.3
8.3
10.4
10.4
12.5
12.5
14.6
14.6
16.7
16.7
13.1
13.1
15.2
17.3
17.3
19.5
25.9
8.8
13.1
17.3
5
6.6
6.6
8.2
8.8
8.8
10.9
10.9
13.1
13.1
15.2
15.2
17.3
17.3
19.5
21.6
21.6
23.8
32.3
8.8
13.1
17.3
21.6
8.8
13
17.3
21.6
4.3
4.3
6.5
6.5
8.7
8.7
10.8
10.8
12.9
12.9
15.1
15.1
17.2
17.2
14
14
16.3
18.6
18.6
20.9
27.8
9.4
14
18.6
5.4
7.1
7.1
8.8
9.4
9.4
11.7
11.7
14
14
16.3
16.3
18.6
18.6
20.9
23.2
23.2
25.5
34.7
9.4
14
18.6
23.2
9.4
14
18.6
23.2
4.6
4.6
6.9
6.9
9.2
9.2
11.5
11.5
13.8
13.8
16.1
16.1
18.4
18.4
15.1
15.1
17.6
20.1
20.1
22.6
10.1
15.1
20.1
5.7
7.6
7.6
9.5
10.1
10.1
12.6
12.6
15.1
15.1
17.6
17.6
20
20
22.5
SQUARE
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
2
2
2
2
2
2
2
2
2
2
2
2
2
2
30'
BALL
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
2
2
2
2
2
2
2
2
2
2
2
2
2
2
CARBIDE
RADIUS
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.8
0.8
0.8
0.8
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Effective length
for inclined angle
Type
TAPER
MS2XLBR0060N120
R0060N120S06
R0060N140
R0060N160
R0060N160S06
R0060N180
R0060N240
R0070N080
R0070N120
R0070N160
R0075N045S06
R0075N060
R0075N060S06
R0075N075S06
R0075N080
R0075N080S06
R0075N100
R0075N100S06
R0075N120
R0075N120S06
R0075N140
R0075N140S06
R0075N160
R0075N160S06
R0075N180
R0075N200
R0075N200S06
R0075N220
R0075N300
R0080N080
R0080N120
R0080N160
R0080N200
R0090N080
R0090N120
R0090N160
R0090N200
R0100N040
R0100N040S06
R0100N060
R0100N060S06
R0100N080
R0100N080S06
R0100N100
R0100N100S06
R0100N120
R0100N120S06
R0100N140
R0100N140S06
R0100N160
R0100N160S06
Ball Nose
R
D1
D5
ap
L3
L1
D4
B2
25
*
*
10.1
15.1
20
SOLID END MILLS
Order Number
Stock
Unit : mm
10.1
15
20
4.9
4.9
7.4
7.4
9.9
9.9
12.4
12.4
14.9
14.9
17.4
17.4
19.9
19.9
* No interference
CUTTING CONDITIONS
I211
I083
MSTAR END MILLS
MS2XLB
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
I084
Order Number
MS2XLBR0100N180
R0100N180S06
R0100N200
R0100N200S06
R0100N220
R0100N250
R0100N250S06
R0100N300
R0100N300S06
R0100N350
R0100N350S06
R0125N060S06
R0125N075S06
R0125N100S06
R0125N125S06
R0125N160S06
R0125N200S06
R0125N250S06
R0125N300S06
R0125N350S06
R0150N080
R0150N100
R0150N120
R0150N140
R0150N160
R0150N200
R0150N250
R0150N300
R0150N350
R0150N400
R0200N100
R0200N120
R0200N140
R0200N160
R0200N200
R0200N250
R0200N300
R0200N350
R0200N400
R0200N450
R0200N500
R0250N200
R0250N250
R0250N300
R0250N350
R0300N300
R0300N500
Ball Nose
R
D1
D4
D5
ap
L3
L1
B2
1
1
1
1
1
1
1
1
1
1
1
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
3
3
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
18
18
20
20
22
25
25
30
30
35
35
6
7.5
10
12.5
16
20
25
30
35
8
10
12
14
16
20
25
30
35
40
10
12
14
16
20
25
30
35
40
45
50
20
25
30
35
30
50
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
4.9
4.9
4.9
4.9
5.85
5.85
2.8
4.7
2.5
4.3
2.3
2.1
3.7
1.8
3.2
1.6
2.8
8.6
7.7
6.5
5.6
4.7
4
3.3
2.9
2.5
7
6
5.3
4.7
4.3
3.6
3
2.6
2.2
2
4.8
4.1
3.6
3.2
2.7
2.2
1.8
1.6
1.4
1.3
1.2
1.5
1.2
1
0.9

55
60
60
60
60
65
65
70
70
70
80
50
50
50
50
60
60
65
70
80
60
60
60
60
60
70
70
70
80
90
70
70
70
70
70
70
70
80
90
90
100
70
70
80
80
80
120
4
6
4
6
4
4
6
4
6
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Stock
Unit : mm
s
a
s
a
a
s
a
s
s
s
s
a
s
a
s
s
s
s
s
a
a
a
s
a
a
a
a
a
s
a
a
s
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
30'
18.7
18.7
20.8
20.8
22.9
26
26
31.1
31.1
36.3
36.3
6.2
7.8
10.4
13
16.7
20.8
26
31.1
36.3
8.3
10.4
12.5
14.6
16.6
20.8
26
31.1
36.3
41.5
10.4
12.5
14.6
16.6
20.8
25.9
31.1
36.3
41.4
46.6
51.8
20.7
25.9
31.1
36.3
19.4
19.4
21.5
21.5
23.6
26.8
26.8
32.2
32.2
37.5
37.5
6.5
8.1
10.8
13.5
17.2
21.5
26.8
32.2
37.5
8.6
10.8
12.9
15
17.2
21.5
26.8
32.2
37.5
42.9
10.7
12.9
15
17.1
21.4
26.8
32.1
37.5
42.8
48.2
53.5
21.4
26.7
*
*
*
*
*
*
20.7
20.7 22.3
23
23
24.8
25.3
28.8
28.8 31
*
*
*
*
34.5
37.3
*
*
40.3
6.9
7.4
8.6
9.2
11.5 12.3
14.4 15.4
18.4 19.8
23
24.8
28.7 31
34.5
40.2
9.2
9.8
11.5 12.3
13.8 14.8
16.1 17.3
18.4 19.7
23
24.7
28.7
34.5
40.2
*
*
11.4
13.7
16
18.3
22.9
28.6
*
*
*
*
12.2
14.6
17.1
19.6
*
*
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
No interference
CUTTING CONDITIONS
I211
MS2XLB
- Inch sizes
Carbon Steel, Alloy Steel, Cast Iron Tool steel, Pre-Hardened Steel
(<30HRC)
( < 45HRC)
Hardened steel
( < 55HRC)
0 -.0008"
e.0004"
Hardened steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
D4 = .1250"
D4 = .1875"
D4 = .2500"
h6
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
Aluminum Alloy
CARBIDE
UWC
Type 2
SQUARE
Type 1
.0078
.0078
.0078
.0156
.0156
.0156
.0313
.0313
.0313
.0469
.0469
.0469
.0625
.0938
.1250
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
.0156
.0156
.0156
.0313
.0313
.0313
.0625
.0625
.0625
.0938
.0938
.0938
.1250
.1875
.2500
.0156
.0156
.0156
.0313
.0313
.0313
.0625
.0625
.0625
.0938
.0938
.0938
.1250
.1875
.2500
.0938
.1250
.1875
.1875
.2500
.3750
.3750
.5000
.7500
.5625
.7500
1.1250
.7500
1.1250
1.5000
.0144
.0144
.0144
.0301
.0301
.0301
.0601
.0601
.0601
.0898
.0898
.0898
.1211
.1836
.2441
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.5
2.0
2.5
3.0
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1875
.2500
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
I212
RADIUS
Dia.
TAPER
MS2XLBD1/64N0094
D1/64N0125
D1/64N0187
D1/32N0187
D1/32N0250
D1/32N0375
D1/16N0375
D1/16N0500
D1/16N0750
D3/32N0562
D3/32N0750
D3/32N1125
D1/8N0750
D3/16N1125
D1/4N1500
Radius of
Ball Nose
R
Stock
Order Number
SOLID END MILLS
Unit : inch
BALL
a 2 ute, long neck, ball nose end mill for general purpose.
I085
MSTAR END MILLS
MS4XLB
- Inch sizes
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
0 -.0008"
e.0004"
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
D4 = .1250"
D4 = .1875"
D4 = .2500"
h6
Copper Alloy
0 -.00024"
0 -.00031"
0 -.00035"
Aluminum Alloy
SQUARE
Type 1
UWC
Type 2
a 4 ute, long neck, ball nose end mill for general purpose.
Order Number
Dia.
.0313
.0313
.0313
.0469
.0469
.0469
.0625
.0938
.1250
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
.0625
.0625
.0625
.0938
.0938
.0938
.1250
.1875
.2500
.0625
.0625
.0625
.0938
.0938
.0938
.1250
.1875
.2500
.3750
.5000
.7500
.5625
.7500
1.1250
.7500
1.1250
1.5000
.0601
.0601
.0601
.0898
.0898
.0898
.1211
.1836
.2441
2.0
2.0
2.0
2.0
2.0
2.5
2.0
2.5
3.0
.1250
.1250
.1250
.1250
.1250
.1250
.1250
.1875
.2500
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
2
2
2
SOLID END MILLS
TAPER
RADIUS
MS4XLBD1/16N0375
D1/16N0500
D1/16N0750
D3/32N0562
D3/32N0750
D3/32N1125
D1/8N0750
D3/16N1125
D1/4N1500
Radius of
Ball Nose
R
Stock
BALL
Unit : inch
I086
CUTTING CONDITIONS
I212
MS2XB
Ball nose end mill, 2 ute, Taper neck
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
0 -0.020
e0.01
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
D4 = 8
h6
Copper Alloy
0 - 0.008
0 - 0.009
Aluminum Alloy
CARBIDE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
30' 0.2
30' 0.2
1
0.2
1
0.2
130' 0.2
130' 0.2
2
0.2
2
0.2
3
0.2
3
0.2
5
0.2
30' 0.3
1
0.3
130' 0.3
2
0.3
3
0.3
5
0.3
30' 0.4
30' 0.4
30' 0.4
30' 0.4
1
0.4
1
0.4
1
0.4
1
0.4
130' 0.4
130' 0.4
130' 0.4
130' 0.4
2
0.4
2
0.4
2
0.4
2
0.4
30' 0.5
30' 0.5
1
0.5
1
0.5
1.5
2
1.5
2
1.5
2
1.5
2
1.5
2
2
3
3
3
3
3
3
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
3
5
3
5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.7
0.7
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.5
1.5
1.5
1.5
8.8
8.5
8.8
8.5
8.9
8.6
8.9
8.6
9.0
8.7
9.0
7.9
7.9
8.0
8.1
8.2
8.6
8.4
7.8
7.3
6.8
8.4
7.9
7.4
6.9
8.5
7.9
7.5
7.0
8.5
8.0
7.5
7.1
7.8
6.8
7.8
6.9
0.19
0.20
0.21
0.22
0.22
0.25
0.24
0.27
0.27
0.32
0.42
0.32
0.36
0.40
0.44
0.52
0.68
0.38
0.40
0.41
0.43
0.39
0.43
0.46
0.50
0.41
0.46
0.51
0.56
0.42
0.49
0.56
0.63
0.49
0.53
0.52
0.59
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Effective length
for inclined angle
30'
1.7
2.2

3.2

2.3
3.3
4.3
5.3

3.3
5.3

1.8
2.4
1.8
2.3

3.4
3.3

2.4
3.5
4.5
5.6
2.3
3.3
4.3
5.3

3.5
5.6
3.4
5.4
2.0
2.6
2.0
2.5
1.9
2.4
1.8
2.3

3.8
3.7
3.5
3.3

2.7
3.9
5.1
6.2
2.6
3.7
4.9
6.0
2.5
3.6
4.7
5.7
2.5
3.5
4.5
5.5
3.9
6.2
3.8
6.0
2.3
3.0
2.2
2.9
2.2
2.8
2.1
2.6
1.9
2.4

4.3
4.2
4.0
3.8
3.4

3.0
4.4
5.7
7.1
3.0
4.2
5.5
6.8
2.9
4.1
5.3
6.5
2.8
4.0
5.1
6.2
4.4
7.1
4.3
6.8
CUTTING CONDITIONS
I213
BALL
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.25
0.25
0.25
0.25
Unit : mm
RADIUS
MS2XBR0010T0030L015
R0010T0030L020
R0010T0100L015
R0010T0100L020
R0010T0130L015
R0010T0130L020
R0010T0200L015
R0010T0200L020
R0010T0300L015
R0010T0300L020
R0010T0500L020
R0015T0030L030
R0015T0100L030
R0015T0130L030
R0015T0200L030
R0015T0300L030
R0015T0500L030
R0020T0030L020
R0020T0030L030
R0020T0030L040
R0020T0030L050
R0020T0100L020
R0020T0100L030
R0020T0100L040
R0020T0100L050
R0020T0130L020
R0020T0130L030
R0020T0130L040
R0020T0130L050
R0020T0200L020
R0020T0200L030
R0020T0200L040
R0020T0200L050
R0025T0030L030
R0025T0030L050
R0025T0100L030
R0025T0100L050
Radius of Dia. Taper Angle Length of Neck Length of Cutting Edge to Neck Overall Shank No. of
Ball Nose
One Side Cut Length Straight Neck Shank Angle Dia. Length Dia. Flutes
B1
R
D1
ap L13
B2 D13 L1
D4
L3
Type
Order Number
Stock
Inclined angle
TAPER
a 2 ute taper neck ball nose end mill.
SOLID END MILLS
Effective
length
Effective length
for inclined angle
UWC
SQUARE
Type 1
I087
MSTAR END MILLS
MS2XB
I088
Order Number
MS2XBR0025T0130L030
R0025T0130L050
R0025T0200L030
R0025T0200L050
R0030T0030L050
R0030T0030L080
R0030T0100L050
R0030T0100L080
R0030T0100L100
R0030T0100L120
R0030T0100L150
R0030T0130L050
R0030T0130L080
R0030T0200L060
R0030T0200L080
R0040T0030L080
R0040T0030L120
R0040T0100L080
R0040T0100L120
R0040T0130L080
R0040T0130L120
R0040T0200L080
R0040T0300L120
R0050T0030L100
R0050T0030L150
R0050T0030L200
R0050T0030L250
R0050T0030L300
R0050T0100L100
R0050T0100L150
R0050T0100L200
R0050T0100L250
R0050T0100L300
R0050T0100L350
R0050T0130L100
R0050T0130L150
R0050T0130L200
R0050T0200L150
R0050T0200L200
R0050T0300L200
R0050T0300L400
R0050T0500L200
R0060T0030L120
R0060T0030L240
R0060T0100L120
R0060T0100L240
R0060T0130L120
R0060T0130L240
R0060T0200L120
R0060T0200L240
R0075T0030L100
Ball Nose
B1
R
D1
ap L13
B2 D13 L1
D4
L3
Type
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
Stock
Unit : mm
0.25
0.25
0.25
0.25
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.75
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.5
130'
130'
2
2
30'
30'
1
1
1
1
1
130'
130'
2
2
30'
30'
1
1
130'
130'
2
3
30'
30'
30'
30'
30'
1
1
1
1
1
1
130'
130'
130'
2
2
3
3
5
30'
30'
1
1
130'
130'
2
2
30'
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.5
3
5
3
5
5
8
5
8
10
12
15
5
8
6
8
8
12
8
12
8
12
8
12
10
15
20
25
30
10
15
20
25
30
35
10
15
20
15
20
20
40
20
12
24
12
24
12
24
12
24
10
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.7
2.7
2.7
2.7
2.7
2.7
2.7
2.7
3
7.9
7.0
7.9
7.1
6.8
5.7
6.8
5.8
5.2
4.8
4.2
6.9
5.9
6.6
6.0
5.5
4.5
5.6
4.6
5.8
4.8
5.9
5.2
6.1
5.1
4.4
3.8
3.4
6.2
5.2
4.5
3.9
3.5
3.2
6.3
5.3
4.6
5.4
4.7
5.0
3.4
5.7
5.6
3.8
5.7
3.9
5.8
4.1
5.9
4.2
5.9
0.54
0.65
0.57
0.71
0.62
0.68
0.68
0.79
0.86
0.93
1.03
0.74
0.90
0.87
1.01
0.87
0.94
0.98
1.12
1.09
1.30
1.20
1.83
1.08
1.16
1.25
1.34
1.42
1.21
1.38
1.56
1.73
1.91
2.08
1.34
1.60
1.86
1.82
2.17
2.78
4.88
4.01
1.31
1.52
1.47
1.89
1.63
2.26
1.79
2.63
1.57
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
60
50
60
50
60
60
60
60
60
70
70
70
60
60
70
70
70
80
60
60
70
60
70
70
80
70
60
70
60
70
60
70
60
70
60
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
a
s
a
s
a
s
a
s
a
s
a
a
s
a
s
a
s
a
s
s
s
s
s
s
s
s
s
a
Effective length
for inclined angle
30'

5.3
8.3

8.3
12.3

10.4
15.4
20.4
25.4
30.4

12.4
24.4

10.4

5.6
8.7
5.4
8.4
10.4
12.4
15.4

8.7
13.0
8.4
12.4

10.9
16.2
21.5
26.8
32.0
10.5
15.5
20.5
25.5
30.5
35.5

13.1
25.7
12.5
24.5

10.9
3.7
5.8
3.5
5.5
6.2
9.8
6.0
9.4
11.6
13.9
17.2
5.8
9.0
6.6
8.6
9.8
14.5
9.4
13.9
9.0
13.2
8.6

12.2
18.2
24.1
30.0
35.9
11.8
17.4
23.0
28.6
34.2
39.8
11.3
16.6
21.9
15.8
20.8

14.6
28.8
14.0
27.5
13.4
26.2
12.8
24.8
12.2
4.1
6.6
4.0
6.3
7.1
11.1
6.8
10.7
13.2
15.8
19.6
6.6
10.2
7.4
9.7
11.1
16.5
10.7
15.8
10.2
15.0
9.7
12.8
13.9
20.7
27.4
34.2
41.0
13.4
19.8
26.2
32.6
39.0
45.4
12.8
18.9
24.9
18.0
23.7
21.2
41.2

16.6
32.8
15.9
31.3
15.2
29.8
14.6
28.3
13.8
15
30
10
15
20
30
10
15
30
10
15
30
20
30
40
20
25
30
35
40
50
20
30
40
30
40
30
40
20
38
30
40
50
30
40
50
30
40
50
30
48
30
50
60
60
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
4.9
3.2
6.0
5.0
4.2
3.3
6.1
5.1
3.4
6.2
5.2
3.5
3.9
2.9
2.4
4.0
3.4
3.0
2.7
2.5
2.1
4.1
3.1
2.6
3.3
2.7
3.5
2.9
5.1
4.6
2.4
1.9
1.6
2.5
2.0
1.7
2.6
2.1
1.7
2.7
1.9
2.9
2.9
1.0
1.0
1.65 60
1.92 70
1.69 60
1.86 60
2.04 70
2.39 70
1.81 60
2.07 60
2.86 70
1.93 60
2.28 60
3.33 70
2.18 60
2.36 70
2.53 80
2.46 60
2.64 60
2.81 70
2.99 80
3.16 80
3.51 90
2.74 60
3.27 70
3.79 80
3.72 70
4.42 80
4.63 70
5.68 80
4.70 60
7.85 80
3.32 70
3.50 80
3.67 90
3.74 70
4.09 80
4.44 90
4.16 70
4.69 80
5.21 90
4.58 70
5.84 90
5.42 70
7.52 90
4.83 110
5.76 110
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
6
6
6
6
6
6
6
6
6
6
8
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
a
s
a
s
a
a
s
a
s
s
a
s
a
s
s
a
s
a
s
a
s
s
a
a
s
a
s
a
s
a
s
a
s
a
s
a
s
a
s
a
s
a
15.4
30.4

20.7
30.7
40.7

30.7
40.7
50.7

60.8
16.2
32.0
10.5
15.5
20.5
30.5

21.7
32.3
42.8
20.8
25.8
30.8
35.8
40.8
50.8

32.3
42.9
53.4
31.0
41.0
51.0

64.0
61.1
18.1
35.9
11.8
17.4
23.0
34.2
11.3
16.6
32.5
10.9
15.9
30.9
24.3
36.2
48.0
23.3
28.9
34.5
40.1
45.8
57.0
22.3
32.9
43.5
31.3
41.3

36.2
20.6
40.9
13.3
19.7
26.1
39.0
12.8
18.9
37.0
12.3
18.0
35.1
27.6
*
*
26.4
32.9
39.3
*
*
*
25.3
37.4
35.5
31.8

*
* *
* *
34.7
*
45.9
*
*
*
33.1
*
43.8
*
*
*
31.6
*
* *
*

*
* *
* *
No interference
CUTTING CONDITIONS
SQUARE
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
BALL
30'
30'
1
1
1
1
130'
130'
130'
2
2
2
30'
30'
30'
1
1
1
1
1
1
130'
130'
130'
2
2
3
3
5
5
30'
30'
30'
1
1
1
130'
130'
130'
2
2
3
3
30'
1
RADIUS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
30'
CARBIDE
TAPER
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
Effective length
for inclined angle
I213
SOLID END MILLS
MS2XBR0075T0030L150
R0075T0030L300
R0075T0100L100
R0075T0100L150
R0075T0100L200
R0075T0100L300
R0075T0130L100
R0075T0130L150
R0075T0130L300
R0075T0200L100
R0075T0200L150
R0075T0200L300
R0100T0030L200
R0100T0030L300
R0100T0030L400
R0100T0100L200
R0100T0100L250
R0100T0100L300
R0100T0100L350
R0100T0100L400
R0100T0100L500
R0100T0130L200
R0100T0130L300
R0100T0130L400
R0100T0200L300
R0100T0200L400
R0100T0300L300
R0100T0300L400
R0100T0500L200
R0100T0500L380
R0150T0030L300
R0150T0030L400
R0150T0030L500
R0150T0100L300
R0150T0100L400
R0150T0100L500
R0150T0130L300
R0150T0130L400
R0150T0130L500
R0150T0200L300
R0150T0200L480
R0150T0300L300
R0150T0300L500
R0200T0030L600
R0200T0100L600
Ball Nose
R
D1
B1
L3
B2 D13 L1
D4
ap L13
Type
Order Number
Stock
Unit : mm
I089
MSTAR END MILLS
MS2MRB
Corner radius end mill, Medium cut length, 2 ute
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
0 -0.020
h6
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
8 < D4 < 10
D4 = 12
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
SQUARE
Type 1
Type 2
UWC
a 2 ute corner radius end mill for general use.
BALL
Unit : mm
TAPER
RADIUS
MS2MRBD0100R010
D0100R020
D0100R030
D0150R010
D0150R020
D0150R030
D0150R050
D0200R010
D0200R020
D0200R030
D0200R050
D0250R010
D0250R020
D0250R030
D0250R050
D0300R010
D0300R020
D0300R030
D0300R050
D0300R100
D0400R010
D0400R020
D0400R030
D0400R050
D0400R100
D0500R010
D0500R020
D0500R030
D0500R050
D0500R100
D0600R010
D0600R020
D0600R030
D0600R050
D0600R100
D0600R150
D0600R200
SOLID END MILLS
I090
Length of
Cut
ap
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
1
1
1
1.5
1.5
1.5
1.5
2
2
2
2
2.5
2.5
2.5
2.5
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
6
6
6
6
6
6
6
0.1
0.2
0.3
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
1.5
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
6
6
6
6
6
8
8
8
8
8
10
10
10
10
10
12
12
12
12
12
12
12
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
a
a
s
a
a
a
s
a
a
a
s
a
a
a
s
a
a
a
a
s
a
a
a
a
s
a
a
a
a
s
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
Unit : mm
0.2
0.3
0.5
1
1.5
2
2.5
3
0.2
0.3
0.5
1
1.5
2
2.5
3
0.2
0.3
0.5
1
1.5
2
2.5
3
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
24
24
24
24
24
24
24
24
60
60
60
60
60
60
60
60
70
70
70
70
70
70
70
70
75
75
75
75
75
75
75
75
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
SQUARE
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
CARBIDE
SOLID END MILLS
MS2MRBD0800R020
D0800R030
D0800R050
D0800R100
D0800R150
D0800R200
D0800R250
D0800R300
D1000R020
D1000R030
D1000R050
D1000R100
D1000R150
D1000R200
D1000R250
D1000R300
D1200R020
D1200R030
D1200R050
D1200R100
D1200R150
D1200R200
D1200R250
D1200R300
Type
BALL
Shank
Dia.
D4
RADIUS
Overall
Length
L1
TAPER
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
Order Number
CUTTING CONDITIONS
I194
I091
MSTAR END MILLS
MS2XLRB
Corner radius end mill, Short cut length, 2 ute, Long neck
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
0 -0.020
Austenitic
Stainless Steel
Titanium Alloy
h6
D4 = 6
Copper Alloy
0 - 0.008
Aluminum Alloy
Type 1
Effective
length
SQUARE
Effective length
for inclined angle
UWC
Type 2
a 2 ute long neck corner radius end mill.

Inclined angle
SOLID END MILLS
TAPER
RADIUS
I092
Order Number
MS2XLRBD0100R010N020
D0100R010N050
D0200R010N040
D0200R010N100
D0200R030N040
D0200R030N100
D0300R010N060
D0300R010N150
D0300R030N060
D0300R030N150
D0400R010N080
D0400R010N200
D0400R030N080
D0400R030N200
D0400R050N080
D0400R050N200
D0600R010N120
D0600R010N300
D0600R030N120
D0600R030N300
D0600R050N120
D0600R050N300
Dia. Corner Length of Neck Neck Cutting Edge to Overall Shank No. of
Radius Cut Length Dia. Shank Angle Length Dia. Flutes
D1
D5
ap
L3
L1
D4
B2
R
1
1
2
2
2
2
3
3
3
3
4
4
4
4
4
4
6
6
6
6
6
6
0.1
0.1
0.1
0.1
0.3
0.3
0.1
0.1
0.3
0.3
0.1
0.1
0.3
0.3
0.5
0.5
0.1
0.1
0.3
0.3
0.5
0.5
1
1
2
2
2
2
3
3
3
3
4
4
4
4
4
4
6
6
6
6
6
6
2
5
4
10
4
10
6
15
6
15
8
20
8
20
8
20
12
30
12
30
12
30
0.94 12.3
0.94 9.8
1.90 9.9
1.90 6.5
1.90 10
1.90 6.6
2.90 7.4
2.90 4.2
2.90 7.5
2.90 4.2
3.90 4.9
3.90 2.5
3.90 5
3.90 2.5
3.90 5
3.90 2.5
5.85

5.85

5.85

5.85

5.85

5.85
60
60
60
60
60
60
50
60
50
60
50
60
50
60
50
60
50
70
50
70
50
70
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Stock
BALL
Unit : mm
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
30'
2.1
5.3
4.2
10.5
4.2
10.5
6.3
15.7
6.3
15.7
8.4
20.8
8.4
20.8
8.4
20.8
2.3
5.6
4.4
10.9
4.4
10.8
6.6
16.2
6.6
16.2
8.7
21.6
8.7
21.5
8.7
21.5
2.4
6.0
4.8
11.7
4.7
11.6
7.1
17.4
7.0
17.4
9.4
23.2
9.3
23.1
9.3
23.1
2.8
6.5
5.2
12.6
5.1
12.6
7.6
18.8
7.6
18.8
10.1
*
*
*
*
*
*
*
*
*
*
*
*
10.1
10.0
*
* *
* *
* *
* *
* *
* *
No interference
CUTTING CONDITIONS
I214
MS4MRB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < 12
D1 > 12
0 -0.020
0 -0.030
D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
h6
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
Type 2
UWC
SQUARE
Type 1
Shank
Dia.
D4
MS4MRBD0300R010
D0300R020
D0300R030
D0300R050
D0300R100
D0400R010
D0400R020
D0400R030
D0400R050
D0400R100
D0500R010
D0500R020
D0500R030
D0500R050
D0500R100
D0600R010
D0600R020
D0600R030
D0600R050
D0600R100
D0600R150
D0600R200
D0800R020
D0800R030
D0800R050
D0800R100
D0800R150
D0800R200
D0800R250
D0800R300
D1000R020
D1000R030
D1000R050
D1000R100
D1000R150
D1000R200
D1000R250
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
1.5
2
0.2
0.3
0.5
1
1.5
2
2.5
3
0.2
0.3
0.5
1
1.5
2
2.5
8
8
8
8
8
11
11
11
11
11
13
13
13
13
13
13
13
13
13
13
13
13
19
19
19
19
19
19
19
19
22
22
22
22
22
22
22
45
45
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
60
60
60
60
70
70
70
70
70
70
70
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
I215
RADIUS
Overall
Length
L1
TAPER
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
Order Number
SOLID END MILLS
Unit : mm
BALL
a 4 ute corner radius end mill for general use.
I093
MSTAR END MILLS
MS4MRB
Unit : mm
Length of
Cut
ap
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
CARBIDE
10
12
12
12
12
12
12
12
12
16
16
16
16
16
16
20
20
20
20
20
20
3
0.2
0.3
0.5
1
1.5
2
2.5
3
0.5
1
1.5
2
2.5
3
0.5
1
1.5
2
2.5
3
22
26
26
26
26
26
26
26
26
32
32
32
32
32
32
38
38
38
38
38
38
70
75
75
75
75
75
75
75
75
90
90
90
90
90
90
100
100
100
100
100
100
10
12
12
12
12
12
12
12
12
16
16
16
16
16
16
20
20
20
20
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Order Number
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
MS4MRBD1000R300
D1200R020
D1200R030
D1200R050
D1200R100
D1200R150
D1200R200
D1200R250
D1200R300
D1600R050
D1600R100
D1600R150
D1600R200
D1600R250
D1600R300
D2000R050
D2000R100
D2000R150
D2000R200
D2000R250
D2000R300
Type
I094
CUTTING CONDITIONS
I215
MSMHDRB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < 12
D1 > 12
0 -0.020
0 -0.030
h6
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
Type 2
UWC
Type 3
SQUARE
Type 1
Shank
Dia.
D4
MSMHDRBD0200R020
D0200R030
D0300R020
D0300R030
D0300R050
D0400R020
D0400R030
D0400R050
D0500R020
D0500R030
D0500R050
D0500R100
D0600R030
D0600R050
D0600R100
D0800R030
D0800R050
D0800R100
D0800R150
D1000R030
D1000R050
D1000R100
D1000R150
D1000R200
D1200R050S10
D1200R100S10
D1200R150S10
D1200R200S10
D1200R300S10
D1200R050
D1200R100
D1200R150
D1200R200
D1200R300
D1600R100
D1600R150
D1600R200
2
2
3
3
3
4
4
4
5
5
5
5
6
6
6
8
8
8
8
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
16
16
16
0.2
0.3
0.2
0.3
0.5
0.2
0.3
0.5
0.2
0.3
0.5
1
0.3
0.5
1
0.3
0.5
1
1.5
0.3
0.5
1
1.5
2
0.5
1
1.5
2
3
0.5
1
1.5
2
3
1
1.5
2
4
4
8
8
8
11
11
11
13
13
13
13
13
13
13
19
19
19
19
22
22
22
22
22
26
26
26
26
26
26
26
26
26
26
35
35
35
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
60
60
60
60
70
70
70
70
70
75
75
75
75
75
75
75
75
75
75
90
90
90
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
16
16
16
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
2
2
2
2
2
2
2
2
I216
RADIUS
Overall
Length
L1
TAPER
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
Order Number
SOLID END MILLS
Unit : mm
BALL
a 4 ute high power corner radius end mill.
I095
MSTAR END MILLS
MSMHDRB
Unit : mm
Length of
Cut
ap
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
CARBIDE
16
18
18
18
18
20
20
20
20
3
1
1.5
2
3
1
1.5
2
3
35
40
40
40
40
45
45
45
45
90
100
100
100
100
110
110
110
110
16
16
16
16
16
20
20
20
20
4
4
4
4
4
4
4
4
4
Order Number
s
s
s
s
s
s
s
s
2
3
3
3
3
2
2
2
2
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
MSMHDRBD1600R300
D1800R100
D1800R150
D1800R200
D1800R300
D2000R100
D2000R150
D2000R200
D2000R300
Type
I096
CUTTING CONDITIONS
I216
MS2MT
Taper end mill, Medium cut length, 2 ute
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
D1 < 0.5
D1 > 0.5
Hardened Steel
(>55HRC)
0 -0.020
0 -0.030
e5'
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
8 < D4 < 10
12 < D4 < 16
h6
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
CARBIDE
Type 2
UWC
a 2 ute taper end mill for general use.
SQUARE
Type 1
Length of
Cut
ap
Large
Mill Dia.
D2
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
MS2MTD0020T0030
D0020T0100
D0020T0130
D0020T0200
D0020T0300
D0020T0400
D0020T0500
D0020T0700
D0020T1000
D0030T0030
D0030T0100
D0030T0130
D0030T0200
D0030T0300
D0030T0400
D0030T0500
D0030T0700
D0030T1000
D0040T0030
D0040T0100
D0040T0130
D0040T0200
D0040T0300
D0040T0400
D0040T0500
D0040T0700
D0040T1000
D0050T0030
D0050T0100
D0050T0130
D0050T0200
D0050T0300
D0050T0400
D0050T0500
D0050T0700
D0050T1000
D0060T0030
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
2
2
2
2
2
2
2
2
2
2
0.21
0.23
0.24
0.26
0.28
0.31
0.34
0.4
0.48
0.32
0.34
0.36
0.38
0.43
0.47
0.51
0.59
0.72
0.43
0.46
0.48
0.51
0.57
0.62
0.68
0.79
0.96
0.53
0.57
0.6
0.64
0.71
0.78
0.85
0.99
1.21
0.63
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
I217
RADIUS
Taper Angle
One Side
B7
TAPER
Small
Mill Dia.
D1
SOLID END MILLS
Order Number
Stock
Unit : mm
BALL
Type 3
I097
MSTAR END MILLS
MS2MT
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
I098
Order Number
Small
Mill Dia.
D1
Taper Angle
One Side
B7
Length of
Cut
ap
Large
Mill Dia.
D2
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
Stock
Unit : mm
MS2MTD0060T0100
D0060T0130
D0060T0200
D0060T0230
D0060T0300
D0060T0400
D0060T0500
D0060T0700
D0060T1000
D0070T0030
D0070T0100
D0070T0130
D0070T0200
D0070T0300
D0070T0400
D0070T0500
D0070T0700
D0070T1000
D0080T0030
D0080T0100
D0080T0130
D0080T0200
D0080T0230
D0080T0300
D0080T0400
D0080T0500
D0080T0700
D0080T1000
D0090T0030
D0090T0100
D0090T0130
D0090T0200
D0090T0300
D0090T0400
D0090T0500
D0090T0700
D0090T1000
D0100T0030
D0100T0100
D0100T0130
D0100T0200
D0100T0230
D0100T0300
D0100T0400
D0100T0500
D0100T0700
D0100T1000
D0150T0030
D0150T0100
D0150T0130
D0150T0200
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1
1 30'
2
2 30'
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
2 30'
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
2 30'
3
4
5
7
10
30'
1
1 30'
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
5
5
5
5
0.67
0.7
0.74
0.77
0.81
0.88
0.95
1.09
1.31
0.73
0.77
0.8
0.84
0.91
0.98
1.05
1.19
1.41
0.85
0.9
0.96
1.01
1.06
1.11
1.22
1.32
1.54
1.86
0.95
1
1.06
1.11
1.21
1.32
1.42
1.64
1.96
1.07
1.14
1.21
1.28
1.35
1.42
1.56
1.7
1.98
2.41
1.59
1.67
1.76
1.85
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
MS2MTD0150T0230
D0150T0300
D0150T0400
D0150T0500
D0150T0700
D0150T1000
D0200T0030
D0200T0100
D0200T0130
D0200T0200
D0200T0230
D0200T0300
D0200T0400
D0200T0500
D0200T0700
D0200T1000
D0250T0030
D0250T0100
D0250T0130
D0250T0200
D0250T0230
D0250T0300
D0250T0400
D0250T0500
D0250T0700
D0250T1000
D0300T0030
D0300T0100
D0300T0130
D0300T0200
D0300T0300
D0300T0400
D0300T0500
D0300T0700
D0300T1000
D0400T0030
D0400T0100
D0400T0130
D0400T0200
D0400T0300
D0400T0400
D0400T0500
D0400T0700
D0400T1000
D0500T0030
D0500T0100
D0500T0130
D0500T0200
D0500T0300
D0500T0400
D0500T0500
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
2 30'
3
4
5
7
10
30'
1
1 30'
2
2 30'
3
4
5
7
10
30'
1
1 30'
2
2 30'
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
3
4
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
15
15
15
15
15
15
15
15
15
20
20
20
20
20
20
20
1.94
2.02
2.2
2.37
2.73
3.26
2.1
2.21
2.31
2.42
2.52
2.63
2.84
3.05
3.47
4.12
2.64
2.78
2.92
3.06
3.2
3.34
3.62
3.9
4.46
5.32
3.17
3.35
3.52
3.7
4.05
4.4
4.75
5.46
6.53
4.26
4.52
4.79
5.05
5.57
6.1
6.62
7.68
9.29
5.35
5.7
6.05
6.4
7.1
7.8
8.5
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
50
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
55
55
55
60
55
55
55
55
55
60
60
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
6
6
6
6
6
6
8
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
2
2
3
2
1
1
1
1
1
1
1
2
3
1
1
1
1
1
3
3
3
3
1
1
3
3
3
3
3
I217
CARBIDE
SQUARE
Large
Mill Dia.
D2
BALL
Length of
Cut
ap
RADIUS
Taper Angle
One Side
B7
TAPER
Small
Mill Dia.
D1
SOLID END MILLS
Order Number
Stock
Unit : mm
I099
MSTAR END MILLS
MS2MT
Order Number
Small
Mill Dia.
D1
MS2MTD0500T0700
D0500T1000
D0600T0030
D0600T0100
D0600T0130
D0600T0200
D0600T0300
D0600T0500
D0800T0030
D0800T0100
D0800T0130
D0800T0200
D0800T0300
D0800T0500
D1000T0030
D1000T0100
D1000T0130
D1000T0200
D1000T0300
D1000T0500
5
5
6
6
6
6
6
6
8
8
8
8
8
8
10
10
10
10
10
10
Taper Angle
One Side
B7
Length of
Cut
ap
Large
Mill Dia.
D2
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
20
20
20
20
20
20
20
20
25
25
25
25
25
25
35
35
35
35
35
35
9.91
12.05
6.35
6.7
7.05
7.4
8.1
9.5
8.44
8.87
9.31
9.75
10.62
12.37
10.61
11.22
11.83
12.44
13.67
16.12
70
80
60
60
60
60
65
70
70
70
70
70
75
95
90
90
90
95
95
95
10
12
6
6
6
6
8
8
8
8
8
8
10
12
10
10
10
12
12
16
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
7
10
30'
1
1 30'
2
3
5
30'
1
1 30'
2
3
5
30'
1
1 30'
2
3
5
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
Stock
Unit : mm
I100
CUTTING CONDITIONS
I217
MS4LT
Taper end mill, Long cut length, 4 ute
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
D1 < 0.5
D1 > 0.5
Hardened Steel
(>55HRC)
0 -0.020
0 -0.040
Austenitic
Stainless Steel
e5'
Titanium Alloy
h6
D4 = 3
4 < D4 < 6
Copper Alloy
0 - 0.006
0 - 0.008
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
Length of
Cut
ap
Large
Mill Dia.
D2
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
MS4LTD0020T0030L02
D0020T0100L02
D0020T0130L02
D0020T0200L02
D0030T0030L03
D0030T0100L03
D0030T0130L03
D0030T0200L03
D0040T0030L04
D0040T0100L04
D0040T0130L04
D0040T0200L04
D0050T0030L04
D0050T0030L06
D0050T0100L04
D0050T0100L06
D0050T0130L04
D0050T0130L06
D0050T0200L04
D0050T0200L06
D0060T0030L04
D0060T0030L06
D0060T0100L04
D0060T0100L06
D0060T0130L04
D0060T0130L06
D0060T0200L04
D0060T0200L06
D0070T0030L06
D0070T0030L08
D0070T0100L06
D0070T0100L08
D0070T0130L06
D0070T0130L08
D0070T0200L06
D0070T0200L08
D0080T0015L04
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.8
30'
1
1 30'
2
30'
1
1 30'
2
30'
1
1 30'
2
30'
30'
1
1
1 30'
1 30'
2
2
30'
30'
1
1
1 30'
1 30'
2
2
30'
30'
1
1
1 30'
1 30'
2
2
15'
2
2
2
2
3
3
3
3
4
4
4
4
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
6
8
6
8
6
8
6
8
4
0.23
0.27
0.3
0.34
0.35
0.4
0.46
0.51
0.47
0.54
0.61
0.68
0.57
0.6
0.64
0.71
0.71
0.81
0.78
0.92
0.67
0.7
0.74
0.81
0.81
0.91
0.88
1.02
0.8
0.84
0.91
0.98
1.01
1.12
1.12
1.26
0.83
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
40
45
40
45
40
45
45
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
a
a
a
a
a
a
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I218
RADIUS
Taper Angle
One Side
B7
TAPER
Small
Mill Dia.
D1
SOLID END MILLS
Order Number
Stock
Unit : mm
BALL
a 4 ute taper end mill for rib milling.
I101
MSTAR END MILLS
MS4LT
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
I102
Order Number
Small
Mill Dia.
D1
MS4LTD0080T0015L06
D0080T0015L08
D0080T0015L10
D0080T0030L04
D0080T0030L06
D0080T0030L08
D0080T0030L10
D0080T0030L12
D0080T0100L04
D0080T0100L06
D0080T0100L08
D0080T0100L10
D0080T0100L12
D0080T0130L04
D0080T0130L06
D0080T0130L08
D0080T0130L10
D0080T0130L12
D0080T0200L04
D0080T0200L06
D0080T0200L08
D0080T0200L10
D0080T0200L12
D0100T0015L06
D0100T0015L08
D0100T0015L10
D0100T0015L12
D0100T0030L06
D0100T0030L08
D0100T0030L10
D0100T0030L12
D0100T0100L06
D0100T0100L08
D0100T0100L10
D0100T0100L12
D0100T0100L16
D0100T0130L06
D0100T0130L08
D0100T0130L10
D0100T0130L12
D0100T0130L16
D0100T0200L06
D0100T0200L08
D0100T0200L10
D0100T0200L12
D0100T0200L16
D0120T0015L06
D0120T0015L10
D0120T0015L12
D0120T0015L16
D0120T0030L06
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
Taper Angle
One Side
B7
Length of
Cut
ap
Large
Mill Dia.
D2
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
Stock
Unit : mm
6
8
10
4
6
8
10
12
4
6
8
10
12
4
6
8
10
12
4
6
8
10
12
6
8
10
12
6
8
10
12
6
8
10
12
16
6
8
10
12
16
6
8
10
12
16
6
10
12
16
6
0.85
0.87
0.89
0.87
0.9
0.94
0.97
1.01
0.94
1.01
1.08
1.15
1.22
1.01
1.11
1.22
1.32
1.43
1.08
1.22
1.36
1.5
1.64
1.05
1.07
1.09
1.1
1.1
1.14
1.17
1.21
1.21
1.28
1.35
1.42
1.56
1.31
1.42
1.52
1.63
1.84
1.42
1.56
1.7
1.84
2.12
1.25
1.29
1.3
1.34
1.3
45
45
45
45
45
45
45
50
45
45
45
45
50
45
45
45
45
50
45
45
45
45
50
45
45
45
50
45
45
45
50
45
45
45
50
55
45
45
45
50
55
45
45
45
50
55
45
45
50
55
45
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
15'
15'
15'
30'
30'
30'
30'
30'
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
30'
30'
30'
30'
30'
15'
15'
15'
15'
30'
30'
30'
30'
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
30'
30'
30'
30'
30'
15'
15'
15'
15'
30'
s
s
s
a
a
a
a
s
a
a
a
a
s
s
s
s
s
s
s
s
s
s
s
s
s
s
a
a
a
a
a
a
a
a
a
a
a
a
a
a
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
30'
30'
30'
30'
30'
30'
1
1 30'
2
30'
1
1 30'
2
15'
15'
15'
15'
15'
15'
30'
30'
30'
30'
30'
30'
1
1
1
1
1
1
1
1 30'
1 30'
1 30'
1 30'
1 30'
1 30'
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
10
12
16
6
10
12
16
20
6
10
12
16
20
6
10
12
16
20
12
12
12
12
12
12
12
12
6
8
10
12
16
20
6
8
10
12
16
20
6
8
10
12
16
20
25
6
8
10
12
16
20
1.37
1.41
1.48
1.41
1.55
1.62
1.76
1.9
1.51
1.72
1.83
2.04
2.25
1.62
1.9
2.04
2.32
2.6
1.51
1.72
1.93
2.14
1.61
1.82
2.03
2.24
1.55
1.57
1.59
1.6
1.64
1.67
1.6
1.64
1.67
1.71
1.78
1.85
1.71
1.78
1.85
1.92
2.06
2.2
2.37
1.81
1.92
2.02
2.13
2.34
2.55
45
50
55
45
45
50
55
55
45
45
50
55
55
45
45
50
55
55
50
50
50
50
50
50
50
50
45
45
45
50
55
55
45
45
45
50
55
55
45
45
45
50
55
55
60
45
45
45
50
55
55
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
a
s
a
s
s
s
a
s
a
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I218
CARBIDE
SQUARE
30'
30'
30'
Large
Mill Dia.
D2
BALL
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.3
1.3
1.3
1.3
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
Length of
Cut
ap
RADIUS
MS4LTD0120T0030L10
D0120T0030L12
D0120T0030L16
D0120T0100L06
D0120T0100L10
D0120T0100L12
D0120T0100L16
D0120T0100L20
D0120T0130L06
D0120T0130L10
D0120T0130L12
D0120T0130L16
D0120T0130L20
D0120T0200L06
D0120T0200L10
D0120T0200L12
D0120T0200L16
D0120T0200L20
D0130T0030L12
D0130T0100L12
D0130T0130L12
D0130T0200L12
D0140T0030L12
D0140T0100L12
D0140T0130L12
D0140T0200L12
D0150T0015L06
D0150T0015L08
D0150T0015L10
D0150T0015L12
D0150T0015L16
D0150T0015L20
D0150T0030L06
D0150T0030L08
D0150T0030L10
D0150T0030L12
D0150T0030L16
D0150T0030L20
D0150T0100L06
D0150T0100L08
D0150T0100L10
D0150T0100L12
D0150T0100L16
D0150T0100L20
D0150T0100L25
D0150T0130L06
D0150T0130L08
D0150T0130L10
D0150T0130L12
D0150T0130L16
D0150T0130L20
Taper Angle
One Side
B7
TAPER
Small
Mill Dia.
D1
SOLID END MILLS
Order Number
Stock
Unit : mm
I103
MSTAR END MILLS
MS4LT
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
I104
Order Number
Small
Mill Dia.
D1
Taper Angle
One Side
B7
Length of
Cut
ap
Large
Mill Dia.
D2
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
Stock
Unit : mm
MS4LTD0150T0130L25
D0150T0200L06
D0150T0200L08
D0150T0200L10
D0150T0200L12
D0150T0200L16
D0150T0200L20
D0150T0200L25
D0160T0030L08
D0160T0030L12
D0160T0030L16
D0160T0030L20
D0160T0100L08
D0160T0100L12
D0160T0100L16
D0160T0100L20
D0160T0130L08
D0160T0130L12
D0160T0130L16
D0160T0130L20
D0160T0200L08
D0160T0200L12
D0160T0200L16
D0160T0200L20
D0180T0015L08
D0180T0015L16
D0180T0015L24
D0180T0030L08
D0180T0030L16
D0180T0030L24
D0180T0100L08
D0180T0100L16
D0180T0100L24
D0180T0130L08
D0180T0130L16
D0180T0130L24
D0180T0200L08
D0180T0200L16
D0180T0200L24
D0200T0015L08
D0200T0015L10
D0200T0015L12
D0200T0015L16
D0200T0015L20
D0200T0015L25
D0200T0030L08
D0200T0030L10
D0200T0030L12
D0200T0030L16
D0200T0030L20
D0200T0030L25
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
2
2
2
2
2
2
2
2
2
2
2
2
2
1 30'
2
2
2
2
2
2
2
30'
30'
30'
30'
1
1
1
1
1 30'
1 30'
1 30'
1 30'
2
2
2
2
15'
15'
15'
30'
30'
30'
1
1
1
1 30'
1 30'
1 30'
2
2
2
15'
15'
15'
15'
15'
15'
30'
30'
30'
30'
30'
30'
25
6
8
10
12
16
20
25
8
12
16
20
8
12
16
20
8
12
16
20
8
12
16
20
8
16
24
8
16
24
8
16
24
8
16
24
8
16
24
8
10
12
16
20
25
8
10
12
16
20
25
2.81
1.92
2.06
2.2
2.34
2.62
2.9
3.25
1.74
1.81
1.88
1.95
1.88
2.02
2.16
2.3
2.02
2.23
2.44
2.65
2.16
2.44
2.72
3
1.87
1.94
2.01
1.94
2.08
2.22
2.08
2.36
2.64
2.22
2.64
3.06
2.36
2.92
3.48
2.07
2.09
2.1
2.14
2.17
2.22
2.14
2.17
2.21
2.28
2.35
2.44
60
45
45
45
50
55
55
60
45
50
55
55
45
50
55
55
45
50
55
55
45
50
55
55
45
55
60
45
55
60
45
55
60
45
55
60
45
55
60
45
45
50
55
55
60
45
45
50
55
55
60
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
a
s
s
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
3
30'
30'
30'
30'
30'
30'
30'
30'
30'
30'
30'
30'
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
30'
30'
30'
30'
30'
30'
30'
1
1
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
30
8
10
12
16
20
25
30
8
10
12
16
20
25
30
8
10
12
16
20
25
30
12
16
20
25
30
10
16
20
25
30
10
16
20
25
30
10
16
20
25
30
10
16
20
25
30
25
40
25
40
2.52
2.28
2.35
2.42
2.56
2.7
2.87
3.05
2.42
2.52
2.63
2.84
3.05
3.31
3.57
2.56
2.7
2.84
3.12
3.4
3.75
4.1
3.26
3.68
4.1
4.62
5.14
2.67
2.78
2.85
2.94
3.02
2.85
3.06
3.2
3.37
3.55
3.02
3.34
3.55
3.81
4.07
3.2
3.62
3.9
4.25
4.6
3.44
3.7
3.87
4.4
65
45
45
50
55
55
60
65
45
45
50
55
55
60
65
45
45
50
55
55
60
65
50
55
55
60
65
45
50
55
60
65
45
50
55
60
65
45
50
55
60
65
45
50
55
60
65
65
80
65
80
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
4
4
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
4
4
4
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
a
s
a
a
s
s
s
a
s
a
a
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I218
CARBIDE
SQUARE
30'
Large
Mill Dia.
D2
BALL
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
Length of
Cut
ap
RADIUS
MS4LTD0200T0030L30
D0200T0100L08
D0200T0100L10
D0200T0100L12
D0200T0100L16
D0200T0100L20
D0200T0100L25
D0200T0100L30
D0200T0130L08
D0200T0130L10
D0200T0130L12
D0200T0130L16
D0200T0130L20
D0200T0130L25
D0200T0130L30
D0200T0200L08
D0200T0200L10
D0200T0200L12
D0200T0200L16
D0200T0200L20
D0200T0200L25
D0200T0200L30
D0200T0300L12
D0200T0300L16
D0200T0300L20
D0200T0300L25
D0200T0300L30
D0250T0030L10
D0250T0030L16
D0250T0030L20
D0250T0030L25
D0250T0030L30
D0250T0100L10
D0250T0100L16
D0250T0100L20
D0250T0100L25
D0250T0100L30
D0250T0130L10
D0250T0130L16
D0250T0130L20
D0250T0130L25
D0250T0130L30
D0250T0200L10
D0250T0200L16
D0250T0200L20
D0250T0200L25
D0250T0200L30
D0300T0030L25
D0300T0030L40
D0300T0100L25
D0300T0100L40
Taper Angle
One Side.
B7
TAPER
Small
Mill Dia.
D1
SOLID END MILLS
Order Number
Stock
Unit : mm
I105
MSTAR END MILLS
MS4LT
CARBIDE
Order Number
3
3
3
3
Taper Angle
One Side.
B7
Length of
Cut
ap
Large
Mill Dia.
D2
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
1 30'
1 30'
2
2
25
40
25
40
4.31
5.09
4.75
5.79
65
80
65
80
6
6
6
6
4
4
4
4
s
s
s
s
Type
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
MS4LTD0300T0130L25
D0300T0130L40
D0300T0200L25
D0300T0200L40
Small
Mill Dia.
D1
Stock
Unit : mm
I106
CUTTING CONDITIONS
I218
MS2MTB
Ball nose taper end mill, Medium cut length, 2 ute
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
e0.01
e5'
Titanium Alloy
Titanium Alloy
Heat Resistant Alloy Heat Resistant Alloy
h6
4 < D4 < 6
Copper Alloy
0 - 0.008
Aluminum Alloy
CARBIDE
UWC
Type 2
SQUARE
Type 1
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.75
0.75
0.75
0.75
0.75
0.75
1
1
1
1
1
1
1
1
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.5
3
5
7
10
3
5
7
10
30'
1
1 30'
2
3
5
7
30'
1
1 30'
2
3
7
30'
1
1 30'
2
3
4
5
7
30'
1
1 30'
2
3
4
5
7
7
Length of
Cut
ap
Large
Mill Dia.
D2
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
3
3
3
3
3
3
3
3
3
3
3
3
3
3
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
14.5
12.5
0.69
0.89
1.09
1.39
0.88
1.07
1.27
1.56
1.04
1.09
1.13
1.18
1.26
1.44
2.36
1.59
1.68
1.78
1.87
2.05
2.8
2.12
2.24
2.37
2.49
2.74
2.98
3.23
3.73
2.65
2.81
2.96
3.11
3.42
3.73
4.04
5.77
5.72
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
40
40
40
40
40
40
45
45
45
45
45
45
45
50
45
45
45
45
45
50
50
60
60
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
4
4
4
4
4
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
I210
RADIUS
MS2MTBR0020T0300
R0020T0500
R0020T0700
R0020T1000
R0030T0300
R0030T0500
R0030T0700
R0030T1000
R0050T0030
R0050T0100
R0050T0130
R0050T0200
R0050T0300
R0050T0500
R0050T0700
R0075T0030
R0075T0100
R0075T0130
R0075T0200
R0075T0300
R0075T0700
R0100T0030
R0100T0100
R0100T0130
R0100T0200
R0100T0300
R0100T0400
R0100T0500
R0100T0700
R0125T0030
R0125T0100
R0125T0130
R0125T0200
R0125T0300
R0125T0400
R0125T0500
R0125T0700
R0150T0700
Taper Angle
One Side
B7
TAPER
Radius of
Ball Nose
R
SOLID END MILLS
Order Number
Stock
Unit : mm
BALL
a 2 ute taper ball nose end mill.
I107
MSTAR END MILLS
MS4LTB
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
e0.03
e5'
Austenitic
Stainless Steel
Titanium Alloy
h6
4 < D4 < 6
Copper Alloy
0 - 0.008
Aluminum Alloy
SQUARE
Type 1
UWC
SOLID END MILLS
TAPER
RADIUS
I108
Unit : mm
Order Number
Radius of
Ball Nose
R
MS4LTBR0030T0030L04
R0030T0030L06
R0030T0100L04
R0030T0100L06
R0030T0130L04
R0030T0130L06
R0030T0200L04
R0030T0200L06
R0040T0030L06
R0040T0030L08
R0040T0030L10
R0040T0100L06
R0040T0100L08
R0040T0100L10
R0040T0130L06
R0040T0130L08
R0040T0130L10
R0040T0200L06
R0040T0200L08
R0040T0200L10
R0050T0030L08
R0050T0030L10
R0050T0030L12
R0050T0030L16
R0050T0100L08
R0050T0100L10
R0050T0100L12
R0050T0100L16
R0050T0130L08
R0050T0130L10
R0050T0130L12
R0050T0130L16
R0050T0200L08
R0050T0200L10
R0050T0200L12
R0050T0200L16
R0060T0030L08
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
Taper Angle
One Side
B7
30'
30'
1
1
1 30'
1 30'
2
2
30'
30'
30'
1
1
1
1 30'
1 30'
1 30'
2
2
2
30'
30'
30'
30'
1
1
1
1
1 30'
1 30'
1 30'
1 30'
2
2
2
2
30'
Length of
Cut
ap
Large
Mill Dia.
D2
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
4
6
4
6
4
6
4
6
6
8
10
6
8
10
6
8
10
6
8
10
8
10
12
16
8
10
12
16
8
10
12
16
8
10
12
16
8
0.66
0.70
0.73
0.80
0.79
0.90
0.86
1.00
0.90
0.93
0.97
1.00
1.07
1.14
1.09
1.20
1.30
1.19
1.33
1.47
1.13
1.17
1.20
1.27
1.26
1.33
1.40
1.54
1.39
1.50
1.60
1.81
1.52
1.66
1.80
2.08
1.33
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
55
50
50
50
55
50
50
50
55
50
50
50
55
50
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Stock
BALL
a 4 ute taper ball nose end mill for rib milling.
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Unit : mm
30'
30'
30'
30'
30'
30'
30'
30'
30'
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
30'
30'
30'
30'
30'
30'
30'
30'
30'
30'
1
1
1
1
1
1
1
1
1
1
2
30'
30'
30'
30'
30'
No. of
Flutes
10
12
16
8
10
12
16
8
10
12
16
8
10
12
16
8
10
12
16
20
8
10
12
16
20
8
10
12
16
20
8
10
12
16
20
8
10
12
16
20
8
10
12
16
20
8
10
12
16
20
8
1.36
1.40
1.47
1.46
1.53
1.60
1.74
1.59
1.69
1.80
2.01
1.72
1.86
2.00
2.28
1.63
1.66
1.70
1.77
1.84
1.75
1.82
1.89
2.03
2.17
1.88
1.98
2.09
2.30
2.51
2.01
2.15
2.29
2.57
2.84
1.92
1.96
1.99
2.06
2.13
2.05
2.12
2.19
2.33
2.47
2.17
2.28
2.38
2.59
2.80
2.30
50
50
55
50
50
50
55
50
50
50
55
50
50
50
55
50
50
50
55
60
50
50
50
55
60
50
50
50
55
60
50
50
50
55
60
50
50
50
55
60
50
50
50
55
60
50
50
50
55
60
50
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
CARBIDE
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I219
SQUARE
Shank
Dia.
D4
BALL
1
1
1
1
1
1
1
1
2
2
2
2
Overall
Length
L1
RADIUS
30'
30'
30'
Large
Mill Dia.
D2
TAPER
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
Length of
Cut
ap
SOLID END MILLS
MS4LTBR0060T0030L10
R0060T0030L12
R0060T0030L16
R0060T0100L08
R0060T0100L10
R0060T0100L12
R0060T0100L16
R0060T0130L08
R0060T0130L10
R0060T0130L12
R0060T0130L16
R0060T0200L08
R0060T0200L10
R0060T0200L12
R0060T0200L16
R0075T0030L08
R0075T0030L10
R0075T0030L12
R0075T0030L16
R0075T0030L20
R0075T0100L08
R0075T0100L10
R0075T0100L12
R0075T0100L16
R0075T0100L20
R0075T0130L08
R0075T0130L10
R0075T0130L12
R0075T0130L16
R0075T0130L20
R0075T0200L08
R0075T0200L10
R0075T0200L12
R0075T0200L16
R0075T0200L20
R0090T0030L08
R0090T0030L10
R0090T0030L12
R0090T0030L16
R0090T0030L20
R0090T0100L08
R0090T0100L10
R0090T0100L12
R0090T0100L16
R0090T0100L20
R0090T0130L08
R0090T0130L10
R0090T0130L12
R0090T0130L16
R0090T0130L20
R0090T0200L08
Taper Angle
One Side
B7
Stock
Order Number
Radius of
Ball Nose
R
I109
MSTAR END MILLS
MS4LTB
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
I110
Order Number
Radius of
Ball Nose
R
MS4LTBR0090T0200L10
R0090T0200L12
R0090T0200L16
R0090T0200L20
R0100T0030L10
R0100T0030L12
R0100T0030L16
R0100T0030L20
R0100T0030L25
R0100T0030L30
R0100T0100L10
R0100T0100L12
R0100T0100L16
R0100T0100L20
R0100T0100L25
R0100T0100L30
R0100T0130L10
R0100T0130L12
R0100T0130L16
R0100T0130L20
R0100T0130L25
R0100T0130L30
R0100T0200L10
R0100T0200L12
R0100T0200L16
R0100T0200L20
R0100T0200L25
R0100T0200L30
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Taper Angle
One Side
B7
2
2
2
2
30'
30'
30'
30'
30'
30'
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
30'
30'
30'
30'
30'
30'
Length of
Cut
ap
Large
Mill Dia.
D2
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
Stock
Unit : mm
10
12
16
20
10
12
16
20
25
30
10
12
16
20
25
30
10
12
16
20
25
30
10
12
16
20
25
30
2.44
2.58
2.86
3.13
2.16
2.19
2.26
2.33
2.42
2.51
2.31
2.38
2.52
2.66
2.84
3.01
2.47
2.58
2.79
3.00
3.26
3.52
2.63
2.77
3.05
3.33
3.68
4.03
50
50
55
60
50
50
55
60
65
65
50
50
55
60
65
65
50
50
55
60
65
65
50
50
55
60
65
65
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
4
4
4
4
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I219
Memo
I111
MIRACLE END MILLS
VCMDSC
End mill, Medium cut length, 4 6 ute
(<30HRC)
( < 45HRC)
CARBIDE
0 -0.020
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
h6
D4 = 6
Copper Alloy
0 - 0.008
Aluminum Alloy
SQUARE
Type 1
UWC
a 4 6 ute end mill with sharp corner geometry for hardened

Unit : mm
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
0.5
1
1.5
2
2.5
3
1
2.5
4
6
8
8
45
45
45
45
45
45
6
6
6
6
6
6
4
4
4
4
4
6
Order Number
VCMDSCD0050
D0100
D0150
D0200
D0250
D0300
s
s
s
s
s
Type
1
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
BALL
steel milling.
I112
CUTTING CONDITIONS
I220
VCLD
End mill, Long cut length, 6 ute
(<30HRC)
( < 45HRC)
D1 < 12
D1 > 12
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
0 -0.020
0 -0.030
D4 = 6
8 < D4 < 10
12 < D4 < 16
20 < D4 < 25
h6
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
6
8
10
12
16
20
25
26
36
46
56
66
76
92
70
90
100
110
130
140
180
6
8
10
12
16
20
25
6
6
6
6
6
6
6
s
s
s
s
s
s
s
1
1
1
1
1
1
1
TAPER
VCLDD0600
D0800
D1000
D1200
D1600
D2000
D2500
Type
SOLID END MILLS
Order Number
RADIUS
Unit : mm
BALL
a 6 ute end mill with long cutting length for hardened steel milling.
CUTTING CONDITIONS
I221
I113
MIRACLE END MILLS
VCMH
End mill, Medium cut length, 3 4 ute, High helix angle
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < 12
D1 > 12
0 -0.020
0 -0.030
D4 = 6
8 < D4 < 10
12 < D4 < 16
20 < D4 < 25
h6
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
SQUARE
Type 1
Type 2
UWC
Type 3
I114
Unit : mm
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
SOLID END MILLS
TAPER
RADIUS
BALL
a 3 4 ute end mill for milling difcult-to-cut and soft materials.
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
20
25
8
11
13
13
16
19
19
22
22
26
26
26
30
32
32
38
45
45
45
50
50
60
60
70
70
75
75
75
75
80
90
90
100
120
6
6
6
6
8
8
10
10
12
12
12
12
16
16
16
20
25
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
Dia.
Order Number
VCMHD0300
D0400
D0500
D0600
D0700
D0800
D0900
D1000
D1100
D1200
D1300
D1400
D1500
D1600
D1800
D2000
D2500
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
2
1
2
1
2
1
2
3
3
1
2
3
2
2
I222
VC6MH
End mill, Medium cut length, 6 ute, High helix angle
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < 12
D1 > 12
0 -0.02
0 -0.03
D4 = 6
8 < D4 < 10
12 < D4 < 16
20 < D4 < 25
h6
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
Shank
Dia.
D4
6
8
10
12
16
20
25
13
19
22
26
32
38
45
50
60
70
75
90
100
120
6
8
10
12
16
20
25
6
6
6
6
6
6
6
s
s
s
s
s
s
s
1
1
1
1
1
1
1
TAPER
VC6MHD0600
D0800
D1000
D1200
D1600
D2000
D2500
Type
SOLID END MILLS
Dia.
Order Number
RADIUS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Unit : mm
BALL
a 6 ute end mill for milling difcult-to-cut and soft materials.
CUTTING CONDITIONS
I223
I115
MIRACLE END MILLS
VC8MH
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
0 -0.03
20 < D4 < 25
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.013
Aluminum Alloy
SQUARE
Type 1
UWC
a 8 ute end mill for milling difcult-to-cut and soft materials.
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
BALL
Unit : mm
20
25
38
45
100
120
20
25
8
8
Dia.
Order Number
1
1
SOLID END MILLS
TAPER
RADIUS
VC8MHD2000
D2500
Type
I116
CUTTING CONDITIONS
I223
VCSFPR
Roughing end mill, Short cut length, 3 4 ute
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
h6
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
Type2
UWC
SQUARE
Type1
Type3
a 3 4 ute roughing end mill for general steel, difcult-to-cut
3
4
5
6
7
8
9
10
10
12
12
14
16
18
20
6
8
10
12
17
17
22
22
22
27
27
27
33
33
38
50
50
50
50
60
60
70
90
70
100
75
75
90
90
100
6
6
6
6
8
8
10
8
10
10
12
12
16
16
20
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
s
s
a
a
a
a
a
s
a
s
a
a
a
a
a
CUTTING CONDITIONS
1
1
1
2
1
2
1
3
2
3
2
3
2
3
2
I224
RADIUS
VCSFPRD0300
D0400
D0500
D0600
D0700
D0800
D0900
D1000S08
D1000
D1200S10
D1200
D1400
D1600
D1800
D2000
Type
TAPER
Shank
Dia.
D4
Dia.
Order Number
SOLID END MILLS
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Unit : mm
BALL
and hardened materials.
I117
MIRACLE END MILLS
VC2ESB
(<30HRC)
( < 45HRC)
CARBIDE
e0.01
0 -0.020
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
h6
4 < D4 < 6
8 < D4 < 10
D4 = 12
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
SQUARE
Type 1
UWC
VC
30
Type 2
a The optimal series for milling in compact machining center.
Order Number
SOLID END MILLS
TAPER
RADIUS
VC2ESBR0015N006
R0020N008
R0030N012
R0040N016
R0050
R0050N025
R0075
R0075N040
R0100
R0100N060
R0150
R0150N080
R0200
R0200N080
R0250
R0250N120
R0300
R0300N130
R0350
R0400
R0500
R0600
I118
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
BALL
Unit : mm
0.3
0.4
0.6
0.8
1
1
1.5
1.5
2
2
3
3
4
4
5
5
6
6
7
8
10
12
0.3
0.4
0.6
0.8
1
1
1.5
1.5
2
2
3
3
4
4
5
5
6
6
7
8
10
12
0.6
0.8
1.2
1.6

2.5

4

6

8

8

12

13

0.27
0.36
0.56
0.76

0.94

1.44

1.9

2.9

3.9

4.9

5.85

30
30
30
30
30
30
30
30
40
40
40
40
40
40
40
40
40
40
50
50
60
65
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Radius of
Ball Nose
R
Dia.
0.15
0.2
0.3
0.4
0.5
0.5
0.75
0.75
1
1
1.5
1.5
2
2
2.5
2.5
3
3
3.5
4
5
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
2
2
I225
VC2PSB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D4 = 6
8 < D4 < 10
D4 = 12
0 -0.01
e0.005
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.005
0 - 0.006
0 - 0.008
Aluminum Alloy
CARBIDE
Type 2
UWC
VC
30
SQUARE
Type 1
Type 3
a MIRACLE NOVA, radial tolerance of e0.005mm,
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
0.6
0.7
0.75
0.8
0.9
1
1.5
2
2.5
3
4
5
6
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.2
1.4
1.5
1.6
1.8
2
3
4
5
6
8
10
12
0.2
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.5
1.8
2.1
2.3
2.4
2.7
3
4.5
6
7.5
9
12
15
18

0.5
0.8
1
1.3
1.5
1.8
2
2.3
2.5
3
3.5
3.8
4
4.5
5
7.5
10
12.5
15
20
25
30

0.17
0.27
0.36
0.46
0.56
0.66
0.76
0.86
0.94
1.14
1.34
1.44
1.54
1.74
1.90
2.90
3.90
4.90
5.85
7.85
9.70
11.70
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
70
70
80
80
90
100
110
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
s
s
a
s
s
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
3
3
3
3
I226
RADIUS
Dia.
TAPER
VC2PSBR0005
R0010
R0015
R0020
R0025
R0030
R0035
R0040
R0045
R0050
R0060
R0070
R0075
R0080
R0090
R0100
R0150
R0200
R0250
R0300
R0400
R0500
R0600
Radius of
Ball Nose
R
SOLID END MILLS
Order Number
Stock
Unit : mm
BALL
diameter tolerance 0 -0.01mm and a shank tolerance of h5.
I119
MIRACLE END MILLS
VC2PSBP
Ball nose, Short cut length, 2 ute, Ultra high precision
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
0 - 0.005
0 - 0.006
0 - 0.008
D4 = 6
8 < D4 < 10
D4 = 12
0 -0.01
e0.002
Copper Alloy
Aluminum Alloy
Type 1
( R0.020.04 is 7.)
SQUARE
Inspection reports regarding the R accuracy of the

VC2PSBP are supplied with the tool.
Type 2
R0.02 0.04
Top edge
geometry
UWC
Type 3
a MIRACLE NOVA, radial tolerance of e0.002mm,
diameter tolerance 0 -0.01mm and a shank tolerance of h5.
Order Number
SOLID END MILLS
TAPER
RADIUS
VC2PSBPR0002
R0003
R0004
R0005
R0010
R0015
R0020
R0025
R0030
R0035
R0040
R0045
R0050
R0060
R0070
R0075
R0080
R0090
R0100
R0150
R0200
R0250
R0300
R0400
R0500
R0600
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
BALL
Unit : mm

0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.2
1.4
1.5
1.6
1.8
2
3
4
5
6
8
10
12
0.06
0.09
0.12
0.2
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.5
1.8
2.1
2.3
2.4
2.7
3
4.5
6
7.5
9
12
15
18

0.5
0.8
1
1.3
1.5
1.8
2
2.3
2.5
3
3.5
3.8
4
4.5
5
7.5
10
12.5
15
20
25
30

0.17
0.27
0.36
0.46
0.56
0.66
0.76
0.86
0.94
1.14
1.34
1.44
1.54
1.74
1.9
2.9
3.9
4.9
5.85
7.85
9.7
11.7
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
70
70
80
80
90
100
110
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Radius of
Ball Nose
R
Dia.
0.02
0.03
0.04
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
0.6
0.7
0.75
0.8
0.9
1
1.5
2
2.5
3
4
5
6
r
r
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
3
3
3
3
(Inspection reports with VC2PSBP.)
ULTRA HIGH
PRECISION
[0.002mm]
I120
a
r

CUTTING CONDITIONS
I226
VCXB
(<30HRC)
( < 45HRC)
e0.01
0 -0.020
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
D4 = 6
8 < D4 < 10
12 < D4 < 16
h6
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
CARBIDE
Type 1
UWC
Type 2
SQUARE
Effective
length
Effective length
for inclined angle
a Ball nose end mill with taper neck.
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
30'
30'
30'
30'
30'
30'
30'
2
2
2
2
2
2
4
4
4
4
4
4
6
6
6
6
6
8
8
8
8
8
10
10
10
10
12
12
12
12
12
14
14
14
14
18
18
16
21
26
23
42
23
21
31
41
23
41
23
31
41
51
52
32
36
46
60
49
28
36
65
61
41
51
65
92
53
34
68
92
55
36
70
100
6.6
5.4
4.6
5.1
3.4
5.8
4.6
3.4
2.7
4.4
2.9
4.9
2.7
2.1
1.7
1.7
2.8
1.7
1.3
1
1.3
2.2
0.9
1.4
1.5
2.3
1.2
1
1.3
1.2
1.9
0.9
1.3
1.2
1.8
0.9
1.8
1.38
1.56
1.73
1.97
5.08
4.46
2.43
2.78
3.13
2.8
5.71
5.02
3.71
4.06
4.41
5.21
5.56
4.81
5.16
5.65
5.95

5.71
6.72
7.42

7.11
7.6
8.54
7.85

9.64
10.47
9.85

11.76
12.8
50
60
70
60
80
60
50
60
70
60
80
60
60
70
80
90
70
70
80
90
90
70
80
110
110
90
90
110
140
110
90
110
140
120
100
130
160
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
10
8
8
10
12
10
10
12
16
1 16.2
1 21.2
1 26.2
1

1

1

1 21.3
1 31.3
1 41.3
1

1

1

1 31.4
1 41.4
1 51.4
1

1

1 36.5
1 46.5
1 60.5
1

2

1
1 65.6
1

2

1 51.8
1 65.8
1 92.8
1

2

1
1 92.8
1

2

1
1 100.7
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
s
s
a
a
a
a
a
s
s
s
s
s
s
17
22.3
27.6
23.9

22.4
33
43.5
24.1

33
43.5
18
23.5
29.1
25.2
42.4

23.6
34.8
25.4
*
*
* *
* *

*
* *
* *
* *
* *

*
* * *
* *
* *

*
* *
* *
* *
* *

*
* * *
* *
* *

*
* * *
* *
* No interference
CUTTING CONDITIONS
RADIUS
1
1
1
1
3
5
1
1
1
1
3
5
1
1
1
1
3
1
1
1
1
3
1
1
1
3
1
1
1
1
3
1
1
1
3
1
1
TAPER
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
4
4
4
4
4
5
5
5
5
6
6
6
6
6
8
8
8
8
10
10
I227
SOLID END MILLS
0.5
0.5
0.5
0.5
0.5
0.5
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2.5
2.5
2.5
2.5
3
3
3
3
3
4
4
4
4
5
5
Effective length
for inclined angle
Type
VCXBR0050T0100L016
R0050T0100L021
R0050T0100L026
R0050T0130
R0050T0300
R0050T0500
R0100T0100L021
R0100T0100L031
R0100T0100L041
R0100T0130
R0100T0300
R0100T0500
R0150T0100L031
R0150T0100L041
R0150T0100L051
R0150T0130
R0150T0300
R0200T0100L036
R0200T0100L046
R0200T0100L060
R0200T0130
R0200T0300
R0250T0100L036
R0250T0100L065
R0250T0130
R0250T0300
R0300T0100L051
R0300T0100L065
R0300T0100L092
R0300T0130
R0300T0300
R0400T0100L068
R0400T0100L092
R0400T0130
R0400T0300
R0500T0100L070
R0500T0100L100
D1
Taper Angle Length of Neck Cutting Edge to Neck Overall Shank

Cut Length Shank Angle Dia. Length Dia.
One Side
L1
B2
D3
B1
D4
ap
L3
Dia.
Stock
Order Number
Radius of
Ball Nose
R
No. of Flutes
Unit : mm
BALL
Inclined angle
I121
MIRACLE END MILLS
VCXB
10
10
12
12
12
12
1 30'
3
1
1
1 30'
3
2
2
2
2
2
2
Dia.
5
5
6
6
6
6
18
18
22
22
22
22
59
40
70
100
83
63
1.1
1.7
1.8
1.2
1.5
2.1

13.62
14.66
15.08
130
110
140
160
160
140
12
12
16
16
16
16
Effective length
for inclined angle
Type
VCXBR0500T0130
R0500T0300
R0600T0100L070
R0600T0100L100
R0600T0130
R0600T0300
D1
Taper Angle Length of Neck Cutting Edge to Neck Overall Shank

Cut Length Shank Angle Dia. Length Dia.
One Side
L1
B2
D3
B1
D4
ap
L3
Radius of
Ball Nose
R
Stock
Order Number
2

2

1 70.9
1 100.9
1

2
s
s
s
s
s
*
*
* *
* *
* *

*
No interference
*
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
No. of Flutes
Unit : mm
I122
CUTTING CONDITIONS
I227
VC3MB
(<30HRC)
( < 45HRC)
R<6
R>8
D1 < 12
D1 > 12
e0.01
e0.02
0 -0.020
0 -0.030
D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
h6
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
Type 2
UWC
SQUARE
Type 1
2
3
4
5
6
8
10
12
16
20
6
8
8
12
12
14
18
22
30
38
60
70
70
80
80
90
100
110
140
160
6
6
6
6
6
8
10
12
16
20
3
3
3
3
3
3
3
3
3
3
1
1.5
2
2.5
3
4
5
6
8
10
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
2
2
2
2
2
2
RADIUS
Shank
Dia.
D4
Dia.
TAPER
VC3MBR0100
R0150
R0200
R0250
R0300
R0400
R0500
R0600
R0800
R1000
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Radius of
Ball Nose
R
SOLID END MILLS
Order Number
Stock
Unit : mm
BALL
a 3 ute ball nose end mill for efcient machining.
CUTTING CONDITIONS
I228
I123
MIRACLE END MILLS
VC4MB
(<30HRC)
( < 45HRC)
CARBIDE
R<6
R>7
D1 < 12
D1 > 12
e0.01
e0.02
0 -0.020
0 -0.030
D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
h6
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
SQUARE
Type 1
Type 2
UWC
Type 3
a Best for high efciency milling of hardened steels and milling in high-
speed machining centers.
Order Number
SOLID END MILLS
TAPER
RADIUS
VC4MBR0050
R0075
R0100
R0150
R0200
R0250
R0300
R0400
R0500
R0600
R0700
R0800
R0900
R1000
I124
Radius of
Ball Nose
R
Dia.
0.5
0.75
1
1.5
2
2.5
3
4
5
6
7
8
9
10
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
BALL
Unit : mm
1
1.5
2
3
4
5
6
8
10
12
14
16
18
20
2.5
4
6
8
8
12
12
14
18
22
26
30
34
38
50
50
60
70
70
80
80
90
100
110
120
140
140
160
6
6
6
6
6
6
6
8
10
12
12
16
16
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
s
a
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
2
2
2
2
3
2
3
2
I229
VCPSRB
(<30HRC)
( < 45HRC)
D4 = 6
8 < D4 < 10
D4 = 12
0 -0.01
e0.01
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.005
0 - 0.006
0 - 0.008
Aluminum Alloy
CARBIDE
Type 1
UWC
Type 2
Inclined angle
SQUARE
Effective
length
Effective length
for inclined angle
a Radius tolerance : R e0.01mm, Diameter tolerance : 0 -0.01mm
0.05
0.1
0.2
0.1
0.2
0.05
0.1
0.2
0.3
0.1
0.2
0.3
0.3
0.05
0.1
0.2
0.3
0.4
0.1
0.2
0.3
0.4
0.3
0.4
0.5
0.5
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
4
4
4
4
4
4
6
6
6
8
4
4
4
4
4
6
6
6
6
10
10
6
10
15
4
4
4
4
6
6
6
6
10
10
0.56
0.56
0.56
0.56
0.56
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.14
1.14
1.14
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
12.6
12.6
12.7
10.9
11
10.7
10.8
10.8
10.9
9.4
9.5
9.5
8.5
10.5
10.5
10.6
10.6
10.7
9.2
9.2
9.3
9.4
7.4
7.4
9.3
7.3
5.8
10.2
10.2
10.3
10.5
8.8
8.9
8.9
9
6.9
7
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
a
s
s
s
a
s
s
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
30'
2.1
2.1
2.1
4.2
4.2
4.2
4.2
4.2
4.2
6.3
6.3
6.3
8.3
4.2
4.2
4.2
4.2
4.2
6.4
6.4
6.3
6.3
10.5
10.5
6.3
10.5
15.7
4.2
4.2
4.2
4.2
6.4
6.4
6.3
6.3
10.6
10.5
2.2
2.2
2.2
4.4
4.3
4.4
4.4
4.3
4.3
6.5
6.5
6.5
8.6
4.5
4.5
4.5
4.5
4.5
6.7
6.7
6.6
6.6
10.9
10.9
6.6
10.9
16.3
4.5
4.5
4.5
4.4
6.7
6.7
6.6
6.6
11
11
2.4
2.3
2.2
4.7
4.7
4.7
4.7
4.7
4.6
7
7
6.9
9.2
4.8
4.8
4.7
4.6
4.4
7.2
7.2
7.2
7.1
11.8
11.7
7.1
11.7
17.5
4.8
4.7
4.6
4.3
7.2
7.2
7.2
7.1
11.8
11.8
2.6
2.6
2.5
5.1
5
5.1
5.1
5
5
7.5
7.5
7.5
10
5.3
5.3
5.3
5.2
5.2
7.8
7.7
7.7
7.7
12.7
12.7
7.7
12.6
18.9
5.3
5.3
5.2
5.2
7.8
7.7
7.7
7.7
12.7
12.7
CUTTING CONDITIONS
I230
RADIUS
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
Effective length
for inclined angle
Type
TAPER
VCPSRBD0060N02R005
D0060N02R01
D0060N02R02
D0060N04R01
D0060N04R02
D0080N04R005
D0080N04R01
D0080N04R02
D0080N04R03
D0080N06R01
D0080N06R02
D0080N06R03
D0080N08R03
D0100N04R005
D0100N04R01
D0100N04R02
D0100N04R03
D0100N04R04
D0100N06R01
D0100N06R02
D0100N06R03
D0100N06R04
D0100N10R03
D0100N10R04
D0120N06R05
D0120N10R05
D0120N15R05
D0150N04R01
D0150N04R02
D0150N04R03
D0150N04R05
D0150N06R01
D0150N06R02
D0150N06R03
D0150N06R05
D0150N10R01
D0150N10R02
Dia. Corner Length Neck Neck Cutting Edge to Overall Shank No. of
Radius of Cut Length Dia. Shank Angle Length Dia. Flutes
D1
L3
D5
L1
D4
B2
R
ap
SOLID END MILLS
Order Number
Stock
Unit : mm
BALL
Suitable for high precision and high efcient machining of die & mold.
I125
MIRACLE END MILLS
VCPSRB
CARBIDE
Order Number
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
VCPSRBD0150N10R03
D0150N10R05
D0150N15R01
D0150N15R02
D0150N15R03
D0150N15R05
D0150N20R03
D0150N20R05
D0200N06R01
D0200N06R02
D0200N06R03
D0200N06R05
D0200N10R01
D0200N10R02
D0200N10R03
D0200N10R05
D0200N15R01
D0200N15R02
D0200N15R03
D0200N15R05
D0200N20R03
D0200N20R05
D0200N25R03
D0200N25R05
D0250N08R01
D0250N08R02
D0250N08R03
D0250N08R05
D0250N08R10
D0250N15R03
D0250N15R05
D0250N15R10
D0300N10R01
D0300N10R02
D0300N10R03
D0300N10R05
D0300N10R10
D0300N15R01
D0300N15R02
D0300N15R03
D0300N15R05
D0300N15R10
D0300N20R01
D0300N20R02
D0300N20R03
D0300N20R05
D0300N20R10
D0300N30R03
D0300N30R05
D0400N12R01
D0400N12R02
D1
D5
L3
L1
D4
B2
R
ap
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
0.3
0.5
0.1
0.2
0.3
0.5
0.3
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.3
0.5
0.3
0.5
0.1
0.2
0.3
0.5
1
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.3
0.5
0.1
0.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
10
10
15
15
15
15
20
20
6
6
6
6
10
10
10
10
15
15
15
15
20
20
25
25
8
8
8
8
8
15
15
15
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
30
30
12
12
1.44 7
1.44 7.1
1.44 5.5
1.44 5.5
1.44 5.5
1.44 5.7
1.44 4.7
1.44 4.8
1.9
9.4
1.9
9.7
1.9 10
1.9 10.3
1.9
7.6
1.9
7.7
1.9
7.8
1.9
8
1.9
5.9
1.9
5.9
1.9
6
1.9
6.1
1.9
4.8
1.9
4.9
1.9
4
1.9
4
2.4
8.6
2.4
8.7
2.4
8.8
2.4
9
2.4
9.4
2.4
5.5
2.4
5.6
2.4
5.7
2.9
6.6
2.9
6.6
2.9
6.6
2.9
6.7
2.9
7
2.9
4.8
2.9
4.8
2.9
4.8
2.9
4.8
2.9
5
2.9
3.7
2.9
3.7
2.9
3.8
2.9
3.8
2.9
3.9
2.9
2.6
2.9
2.6
3.9
3.8
3.9
3.8
50
50
50
50
50
50
60
60
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
50
50
50
50
50
50
50
50
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
70
70
60
60
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Stock
Unit : mm
s
a
s
s
s
s
s
s
s
s
s
a
s
s
s
a
s
s
s
a
s
s
s
s
s
s
s
s
a
s
s
a
s
s
s
a
a
s
s
s
a
a
s
s
s
a
a
s
s
s
s
Effective length
for inclined angle
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
30'
10.5
10.5
15.8
15.8
15.7
15.7
20.9
20.9
6.3
6.3
6.3
6.3
10.5
10.5
10.5
10.5
15.7
15.7
15.7
15.6
20.8
20.8
26
26
8.4
8.4
8.4
8.4
8.3
15.7
15.6
15.6
10.5
10.5
10.5
10.5
10.4
15.7
15.7
15.7
15.6
15.6
20.8
20.8
20.8
20.8
20.8
31.1
31.1
12.5
12.5
10.9
10.9
16.3
16.3
16.3
16.3
21.6
21.5
6.6
6.6
6.6
6.5
10.9
10.8
10.8
10.8
16.1
16.1
16.1
16.1
21.4
21.4
26.6
26.6
8.7
8.7
8.7
8.7
8.7
16.1
16.1
16.1
10.9
10.8
10.8
10.8
10.8
16.1
16.1
16.1
16.1
16.1
21.4
21.4
21.4
21.4
21.3
31.8
31.8
13
13
11.8
11.7
17.5
17.5
17.5
17.4
22.9
22.8
6.9
6.8
6.7
6.5
11.4
11.2
11.1
10.9
16.8
16.7
16.6
16.3
21.9
21.7
27.5
27
9.2
9
8.9
8.7
8.2
16.6
16.3
15.8
11.4
11.2
11.1
10.9
10.4
16.8
16.7
16.6
16.3
15.8
22.1
22
21.9
21.7
21.2
32.5
32.2
13.5
13.4
12.7
12.6
18.9
18.9
18.9
18.6
24.5
24.2
7.5
7.4
7.4
7.4
12
12
11.9
11.9
17.5
17.5
17.4
17.4
22.9
22.9
28.3
28.2
9.9
9.9
9.9
9.9
9.9
17.5
17.5
17.5
12.3
12.3
12.3
12.4
12.4
17.7
17.8
17.8
17.8
17.8
23.1
23.1
23.2
23.2
23.2
*
I126
*
*
15.1
15.2
No interference
12
12
12
20
20
20
20
20
30
30
30
15
15
30
30
18
18
18
18
18
18
41
50
24
24
24
24
24
24
24
50
50
30
30
30
30
30
30
50
50
36
36
36
36
36
36
36
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
4.9
4.9
4.9
4.9
5.85
5.85
5.85
5.85
5.85
5.85
5.85
5.85
7.85
7.85
7.85
7.85
7.85
7.85
7.85
7.85
7.85
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
3.8
3.9
4
2.5
2.5
2.5
2.5
2.6
1.8
1.8
1.8
1.6
1.6
0.9
0.9

60
60
60
60
60
60
60
60
70
70
70
60
60
70
70
70
70
70
70
70
70
90
90
90
90
90
90
90
90
90
90
90
100
100
100
100
100
100
100
100
110
110
110
110
110
110
110
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
a
a
s
s
s
a
a
s
a
a
s
s
s
s
s
s
s
a
a
a
s
s
s
s
s
a
a
a
a
s
s
s
a
a
a
a
a
s
s
s
a
a
a
a
a
a
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
30'
12.5
12.5
12.5
20.8
20.8
20.8
20.8
20.8
31.1
31.1
31.1
15.6
15.6
31.1
31.1
13
13
12.9
21.4
21.4
21.4
21.4
21.3
31.8
31.8
31.8
16.1
16.1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
13.3 15.2
13.1 15.3
12.6 15.3
22.1
22
21.9
21.7
21.2
*
*
*
*
*
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
No interference
CUTTING CONDITIONS
I230
SQUARE
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
BALL
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.3
0.5
1
0.5
1
0.5
1
0.1
0.2
0.3
0.5
1
2
0.5
1
0.1
0.2
0.3
0.5
1
2
3
1
3
0.3
0.5
1
2
3
4
1
3
0.3
0.5
1
2
3
4
5
CARBIDE
RADIUS
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
Effective length
for inclined angle
Type
TAPER
VCPSRBD0400N12R03
D0400N12R05
D0400N12R10
D0400N20R01
D0400N20R02
D0400N20R03
D0400N20R05
D0400N20R10
D0400N30R03
D0400N30R05
D0400N30R10
D0500N15R05
D0500N15R10
D0500N30R05
D0500N30R10
D0600N18R01
D0600N18R02
D0600N18R03
D0600N18R05
D0600N18R10
D0600N18R20
D0600N41R05
D0600N50R10
D0800N24R01
D0800N24R02
D0800N24R03
D0800N24R05
D0800N24R10
D0800N24R20
D0800N24R30
D0800N50R10
D0800N50R30
D1000N30R03
D1000N30R05
D1000N30R10
D1000N30R20
D1000N30R30
D1000N30R40
D1000N50R10
D1000N50R30
D1200N36R03
D1200N36R05
D1200N36R10
D1200N36R20
D1200N36R30
D1200N36R40
D1200N36R50
D1
D5
L3
L1
D4
B2
R
ap
SOLID END MILLS
Order Number
Stock
Unit : mm
I127
MIRACLE END MILLS
VCPSRB
Corner radius, Short cut length, 2-4 ute, Taper neck, High precision
(<30HRC)
( < 45HRC)
CARBIDE
e0.01
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
0 - 0.005
D4 = 6
8 < D4 < 10 0 - 0.006
12 < D4 < 16 0 - 0.008
0 -0.01
Copper Alloy
Aluminum Alloy
Taper neck type

Type 3
Effective
length
SQUARE
Effective length
for inclined angle
UWC
a Radius tolerance : R e0.01mm, Diameter tolerance : 0 -0.01mm
Suitable for high precision and high efcient machining of die & mold.
1.5
1.5
2
2
2.5
2.5
3
3
3
3
4
4
5
5
5
5
6
6
8
8
10
10
12
2
2
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
0.5
0.5
0.5
0.5
1
1
0.5
0.5
1
1
1
1
0.5
0.5
1
1
2
2
2
2
3
3
3
1 30' 1.5
1 30' 1.5
1 30' 2
1 30' 2
1 30' 2.5
1 30' 2.5
1 30' 3
1 30' 3
1 30' 3
1 30' 3
1 30' 4
1 30' 4
1
5
1
5
1
5
1
5
1
6
1
6
1
8
1
8
1
10
1
10
1
12
6
10
10
15
12
20
15
20
15
20
20
30
40
60
40
60
40
60
53
70
55
70
70
3
3
4
4
5
5
6
6
6
6
8
8
8
8
8
8
8
8
10
10
12
12
24
1.44
1.44
1.9
1.9
2.4
2.4
2.9
2.9
2.9
2.9
3.9
3.9
4.9
4.9
4.9
4.9
5.85
5.85
7.85
7.85
9.7
9.7
11.7
9
7.2
6.7
5.3
5.6
4
4.4
3.6
4.4
3.6
2.6
1.9
2
1.4
2
1.4
1.4
1
1.1
1.6
1.1
0.9
1.6
50
50
60
60
60
60
60
60
60
60
60
70
90
110
90
110
70
100
90
130
100
130
130
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
10
12
12
12
16
Type
VCPSRBD0150N03L06R05
D0150N03L10R05
D0200N04L10R05
D0200N04L15R05
D0250N05L12R10
D0250N05L20R10
D0300N06L15R05
D0300N06L20R05
D0300N06L15R10
D0300N06L20R10
D0400N08L20R10
D0400N08L30R10
D0500N08L40R05
D0500N08L60R05
D0500N08L40R10
D0500N08L60R10
D0600N08L40R20
D0600N08L60R20
D0800N10L53R20
D0800N10L70R20
D1000N12L55R30
D1000N12L70R30
D1200N24L70R30
Dia. Corner Taper Angle Length Neck Under Shank Neck Cutting Edge to Overall Shank
Radius One Side of Cut Length Length Dia. Shank Angle Length Dia.
R
B1
L3
L2
B2
L1
D4
D1
D5
ap
Stock
Order Number
No. of Flutes
Unit : mm
BALL
RADIUS
TAPER
SOLID END MILLS
I128
Inclined angle
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
s
s
s
s
a
s
a
s
a
s
s
Effective length
for inclined angle

41.2
61.2
41.7
61.7
42.8
7.1
11.3
11.5
16.7
14.2
22.5
16.9
22.1
17.4
22.6
22.8
7.7
12.2
12.4
18
15.3
24.2
18.2
23.8
18.7
24.4
*
* *
* *
* *
* *
* *
* *
*
*
*
55.9
*
*
72.9
*
*
59.4
* *
* * *
75.2
* *
* No interference
CUTTING CONDITIONS
I231
VC4JRB
Corner radius end mill, Semi long cut length, 4 ute
(<30HRC)
( < 45HRC)
D1 < 12
D1 > 12
0 -0.020
0 -0.030
D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
h6
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
UWC
Type 2
SQUARE
Type 1
Shank
Dia.
D4
VC4JRBD0300R0030
D0400R0030
D0400R0050
D0500R0030
D0500R0050
D0600R0030
D0600R0050
D0600R0100
D0800R0030
D0800R0050
D0800R0100
D0800R0150
D0800R0200
D1000R0030
D1000R0050
D1000R0100
D1000R0150
D1000R0200
D1200R0050
D1200R0100
D1200R0150
D1200R0200
D1600R0050
D1600R0100
D1600R0150
D1600R0200
D2000R0050
D2000R0100
D2000R0150
D2000R0200
3
4
4
5
5
6
6
6
8
8
8
8
8
10
10
10
10
10
12
12
12
12
16
16
16
16
20
20
20
20
0.3
0.3
0.5
0.3
0.5
0.3
0.5
1
0.3
0.5
1
1.5
2
0.3
0.5
1
1.5
2
0.5
1
1.5
2
0.5
1
1.5
2
0.5
1
1.5
2
12
15
15
20
20
20
20
20
25
25
25
25
25
30
30
30
30
30
30
30
30
30
50
50
50
50
55
55
55
55
50
50
50
60
60
60
60
60
70
70
70
70
70
90
90
90
90
90
90
90
90
90
110
110
110
110
110
110
110
110
6
6
6
6
6
6
6
6
8
8
8
8
8
10
10
10
10
10
12
12
12
12
16
16
16
16
20
20
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
I232
RADIUS
Overall
Length
L1
TAPER
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
SOLID END MILLS
Dia.
Order Number
Stock
Unit : mm
BALL
a 4 ute corner radius end mill for longer reach applications.
I129
MIRACLE END MILLS
VCHFRB
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < 12
D1 > 12
e0.015
Austenitic
Stainless Steel
0 -0.02
0 -0.03
Titanium Alloy
h6
D4 = 6
8 < D4 < 10
12 < D4 < 16
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
u
Type 1
Effective
length
SQUARE
Effective length
for inclined angle
UWC
Type 2
Inclined angle
Type 3
a Suitable for high feed and efcient machining of die & mold.
SOLID END MILLS
TAPER
RADIUS
I130
Order Number
D5
ap
L3
L1
D4
D1
R
B2
VCHFRBD0200R050N06
D0200R050N10
D0300R075N09
D0300R075N15
D0400R100N12
D0400R100N20
D0500R120N15
D0600R150N18
D0600R150N30
D0700R150A050
D0700R150A080
D0800R200N24
D0800R200N40
D0900R200A065
D0900R200A100
D1000R200N30
D1000R200N50
D1100R200A070
D1100R200A110
D1200R300N36
D1200R300N60
D1300R300A075
D1300R300A120
D1600R300N80
2
2
3
3
4
4
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
16
0.5
0.5
0.75
0.75
1
1
1.2
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
3
3
3
3
3
2
2
3
3
4
4
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
16
6
10
9
15
12
20
15
18
30

24
40

30
50

36
60

80
1.9
1.9
2.9
2.9
3.9
3.9
4.9
5.85
5.85

7.85
7.85

9.7
9.7

11.7
11.7

15.5
8.7
6.7
6.2
4.3
3.9
2.6
1.9

50
70
50
70
50
70
70
50
90
50
80
60
90
65
100
70
100
70
110
75
110
75
120
140
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
16
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Stock
BALL
Unit : mm
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Effective length
for inclined angle
Type
1
1
1
1
1
1
1
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
30'
6.2
10.4
9.4
15.6
12.4
20.7
15.5
6.5
10.8
9.7
16.1
12.8
21.4
16
6.9
11.5
10.4
17.3
13.7
22.9
7.5
12.4
11.1
18.6
14.7
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
No interference
CUTTING CONDITIONS
I233
VCHFRB
High feed corner radius, taper neck, 4 ute
(<30HRC)
( < 45HRC)
D1 < 12
D1 > 12
e0.015
0 -0.02
0 -0.03
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
D4 = 6
8 < D4 < 10
12 < D4 < 16
h6
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
CARBIDE
Taper neck type

Type 4
Effective
length
SQUARE
Effective length
for inclined angle
UWC
2
2
2
3
3
3
4
4
4
5
5
5
6
6
8
8
10
10
12
12
16
20
18
24
30
24
32
40
30
40
50
50
67
70
90
80
110
110
4
4
4
6
6
6
8
8
8
8
8
8
16
16
18
18
20
20
24
1.9
1.9
1.9
2.9
2.9
2.9
3.9
3.9
3.9
4.9
4.9
4.9
5.85
5.85
7.85
7.85
9.7
9.7
11.7
6
5
4.3
3.8
3
2.6
2.2
1.7
1.4
1
2
1.7
1.2
0.9
0.9
1.3
2
1.5
1.1
70
70
70
80
80
80
90
90
90
90
90
110
110
130
120
150
140
160
160
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
12
16
16
16
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4 12.9
4 16.9
4 20.9
4 19.3
4 25.3
4 31.3
4 25.7
4 33.7
4 41.7
4
4 41.9
4 51.9
4 52.9
4
4
4 93.5
4 83.9
4 113.9
4 115.2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
13.9
18.2
22.5
20.7
27.2
33.6
27.6
15
19.6
24.3
22.3
*
*
*
* *
* *
* * *
* *
* *
* *
* * *
* * *
* *
* *
* *
* *
* No interference
CUTTING CONDITIONS
I233
RADIUS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TAPER
0.5
0.5
0.5
0.75
0.75
0.75
1
1
1
1.2
1.2
1.2
1.5
1.5
2
2
2
2
3
SOLID END MILLS
2
2
2
3
3
3
4
4
4
5
5
5
6
6
8
8
10
10
12
Effective length
for inclined angle
Type
VCHFRBD0200R050N12
D0200R050N16
D0200R050N20
D0300R075N18
D0300R075N24
D0300R075N30
D0400R100N24
D0400R100N32
D0400R100N40
D0500R120N30
D0500R120N40
D0500R120N50
D0600R150N50
D0600R150N67
D0800R200N70
D0800R200N90
D1000R200N80
D1000R200N110
D1200R300N110
Dia. Corner Taper Angle Length Neck Length of Neck Cutting Edge to Overall Shank
Radius One Side of Cut Length Straight Neck Dia. Shank Angle Length Dia.
ap
L3
L2
L1
D4
D5
D1
R
B1
B2
Stock
Order Number
No. ofFlutes
Unit : mm
BALL
Inclined angle
I131
MIRACLE END MILLS
- Inch sizes
VCHFRB
(<30HRC)
( < 45HRC)
CARBIDE
e.0006"
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
0 -.0008"
h6
Titanium Alloy
.250 < D4 < .375" 0 -.00035"

D4 = .500" 0 -.00043"
Copper Alloy
Aluminum Alloy
SQUARE
Type 1
UWC
Type 2
BALL
Unit : inch
Dia.
D1
Corner
Radius
R
Length of
Cut
ap
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
.125
.125
.188
.188
.250
.250
.375
.375
.500
.030
.030
.050
.050
.060
.060
.080
.080
.120
.125
.125
.188
.188
.250
.250
.375
.375
.500
.375
.625
.563
.938
.750
1.250
1.125
1.875
1.500
.1191
.1191
.1796
.1796
.2421
.2421
.3612
.3612
.4843
2.250
2.250
2.250
2.250
3.000
3.000
4.000
4.000
5.000
Order Number
.250
.250
.250
.250
.250
.250
.375
.375
.500
4
4
4
4
4
4
4
4
4
Type
1
1
1
1
2
2
2
2
2
CUTTING CONDITIONS
I234
a
a
a
a
a
a
a
a
SOLID END MILLS
TAPER
RADIUS
VCHFRBD1/8N3DR0.03
D1/8N5DR0.03
D3/16N3DR0.05
D3/16N5DR0.05
D1/4N3DR0.06
D1/4N5DR0.06
D3/8N3DR0.08
D3/8N5DR0.08
D1/2N3DR0.12
Shank No. of
Dia. Flutes Stock
D4
I132
VCMHDRB
Corner radius end mill, Medium cut length, 4 ute, High helix angle
(<30HRC)
( < 45HRC)
D1 < 12
D1 > 12
0 -0.02
0 -0.03
4 < D4 < 6
8 < D4 < 10
12 < D4 < 16
20 < D4 < 25
h6
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
Type 2
UWC
SQUARE
Type 1
Type 3
a 4 ute corner radius end mill with high helix angle and newly
Shank
Dia.
D4
VCMHDRBD0200R020S04
D0200R030S04
D0300R020S06
D0300R030S06
D0300R050S06
D0400R020S06
D0400R030S06
D0400R050S06
D0500R020S06
D0500R030S06
D0500R050S06
D0500R100S06
D0600R030S06
D0600R050S06
D0600R100S06
D0800R030S08
D0800R050S08
D0800R100S08
D0800R150S08
D1000R030S08
D1000R050S08
D1000R100S08
D1000R150S08
D1000R200S08
D1000R030S10
D1000R050S10
D1000R100S10
D1000R150S10
D1000R200S10
D1200R050S10
D1200R100S10
D1200R150S10
D1200R200S10
D1200R300S10
D1200R050S12
D1200R100S12
D1200R150S12
2
2
3
3
3
4
4
4
5
5
5
5
6
6
6
8
8
8
8
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
0.2
0.3
0.2
0.3
0.5
0.2
0.3
0.5
0.2
0.3
0.5
1
0.3
0.5
1
0.3
0.5
1
1.5
0.3
0.5
1
1.5
2
0.3
0.5
1
1.5
2
0.5
1
1.5
2
3
0.5
1
1.5
6
6
8
8
8
11
11
11
13
13
13
13
13
13
13
19
19
19
19
22
22
22
22
22
22
22
22
22
22
26
26
26
26
26
26
26
26
40
40
50
50
50
50
50
50
60
60
60
60
60
60
60
70
70
70
70
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
10
12
12
12
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
3
2
2
2
2
2
3
3
3
3
3
2
2
2
I235
RADIUS
Overall
Length
L1
TAPER
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
Stock
Dia.
Order Number
SOLID END MILLS
Unit : mm
BALL
designed corner radius, for milling difcult-to-cut materials.
I133
MIRACLE END MILLS
VCMHDRB
SQUARE
BALL
RADIUS
Overall
Length
L1
Shank
Dia.
D4
12
12
16
16
16
16
18
18
18
18
20
20
20
20
22
22
22
22
25
25
25
25
2
3
1
1.5
2
3
1
1.5
2
3
1
1.5
2
3
1
1.5
2
3
1
1.5
2
3
26
26
32
32
32
32
32
32
32
32
38
38
38
38
38
38
38
38
45
45
45
45
90
90
110
110
110
110
110
110
110
110
110
110
110
110
140
140
140
140
140
140
140
140
12
12
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
25
25
25
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Dia.
CARBIDE
Order Number
VCMHDRBD1200R200S12
D1200R300S12
D1600R100S16
D1600R150S16
D1600R200S16
D1600R300S16
D1800R100S16
D1800R150S16
D1800R200S16
D1800R300S16
D2000R100S20
D2000R150S20
D2000R200S20
D2000R300S20
D2200R100S20
D2200R150S20
D2200R200S20
D2200R300S20
D2500R100S25
D2500R150S25
D2500R200S25
D2500R300S25
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
2
2
2
2
2
2
3
3
3
3
2
2
2
2
3
3
3
3
2
2
2
2
SOLID END MILLS
TAPER
Length of
Cut
ap
No. of
Flutes
D1
Corner
Radius
R
Stock
Unit : mm
I134
CUTTING CONDITIONS
I235
VC4STB
Ball nose taper end mill, Short cut length, 4 ute
(<30HRC)
( < 45HRC)
e0.01
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
D4 = 6
8 < D4 < 10
h6
Copper Alloy
0 - 0.008
0 - 0.009
Aluminum Alloy
CARBIDE
Type 2
UWC
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.75
0.75
1
1
1
1
1
1
1
1
1
1
1
1.25
1
2
5
10
1
1
2
5
7
10
1
1
1
2
2
2
5
5
5
7
7
7
10
2
5
1
1
1
2
2
2
5
5
5
7
10
5
30'
30'
30'
30'
30'
30'
30'
30'
30'
1
1
1
1
2
2
2
2
7
3
2
2
2
2
2
3
3
3
3
7
7
7
3
3
3
4
4
4
4
4
4
4
4
4
7
4
4
5
5
5
15
10
15
10
10
10
15
10
15
20
10
15
20
10
15
20
10
15
20
14
10
15
10
15
20
6
10
15
10
15
23
17
12
15
9.0
9.0
8.8

14.0
19.0
14.0
13.5
12.2

14.0
19.0
24.0
14.0
18.9
24.0
13.6
17.2
21.8
12.1
16.6

14.0
17.0
13.5
18.5
23.5
8.7
13.8
17.5
12.2
16.8

16.5
0.64
0.65
0.70
0.90
0.88
0.88
0.91
1.08
2.43
1.73
1.08
1.08
1.08
1.11
1.11
1.11
1.44
1.44
1.44
2.60
2.60
2.60
1.90
1.66
1.90
2.16
2.16
2.16
2.20
2.20
2.20
2.50
2.50
2.50
3.49
3.10
2.99
17.2
17.2
17.6
10.4
10.8
8.0
10.8
11.2
12.4
10.1
10.5
7.7
6.1
10.5
7.8
6.1
10.8
8.5
6.7
12.2
8.9
7.3
10.5
9.6
7.9
9.1
6.5
5.1
14.4
8.9
6.9
10.1
7.2
5.2
7.1
10.3
6.6
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
No. of
Flutes
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
a
a
s
s
s
s
s
s
a
s
s
a
a
s
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CUTTING CONDITIONS
Type
1
1
1
3
1
1
1
1
2
3
1
1
1
1
1
1
1
2
2
2
2
3
3
1
2
1
1
1
2
1
2
2
2
3
3
3
2
I236
RADIUS
Radius of Taper Angle Length of Neck Under Shank Large Cutting Edge to Overall Shank
Ball Nose One Side
Cut
Length Length Mill Dia. Shank Angle Length Dia.
L1
D4
R
B7
ap
L3
L2
D2
B2
Stock
Unit : mm
TAPER
VC4STBR0030T0130N05
R0030T0200N05
R0030T0500N05
R0030T1000N15
R0040T0130N10
R0040T0130N15
R0040T0200N10
R0040T0500N10
R0040T0700N10
R0040T1000N15
R0050T0130N10
R0050T0130N15
R0050T0130N20
R0050T0200N10
R0050T0200N15
R0050T0200N20
R0050T0500N10
R0050T0500N15
R0050T0500N20
R0050T0700N10
R0050T0700N15
R0050T0700N20
R0050T1000N14
R0075T0200N10
R0075T0500N15
R0100T0130N10
R0100T0130N15
R0100T0130N20
R0100T0200N06
R0100T0200N10
R0100T0200N15
R0100T0500N10
R0100T0500N15
R0100T0500N23
R0100T0700N17
R0100T1000N12
R0125T0500N15
*Relief Neck type.
SOLID END MILLS
the rigidity to the fullest extent, ensuring the maximum performance

when machining any kind of work material.
BALL
Type 3
a The taper neck and short length of cut are adopted in order to increase
Order Number
SQUARE
Type 1
I135
MIRACLE END MILLS
VC4STB
Order Number
VC4STBR0150T0130N15
R0150T0130N20
R0150T0300N15
R0150T0500N10
R0150T0500N18
R0175T0500N15
R0200T0130N15
R0200T0130N20
R0200T0300N21
R0200T0500N13
R0200T0700N18
R0300T0130N15
R0300T0130N20
R0300T0300N22
R0400T0130N15
R0400T0300N22
Radius of Taper Angle Length of Neck Under Shank Large Cutting Edge to Overall Shank
Ball Nose One Side
Cut
Length Length Mill Dia. Shank Angle Length Dia.
R
B7
ap
L3
L2
D2
B2
L1
D4
1.5
1.5
1.5
1.5
1.5
1.75
2
2
2
2
2
3
3
3
4
4
1
1
3
5
5
5
1
1
3
5
7
1
1
3
1
3
30'
30'
30'
30'
30'
30'
30'
4
4
4
4
4
4
5
5
4
4
7
6
6
6
8
8
15
20
15
10
18
15
15
20
21
13
18
15
20
22
15
22
17.3
22.2
16.9
11.7

16.8
21.6

16.8
21.7

16.9
3.13
3.13
3.27
3.50
3.50
3.91
4.16
4.16
4.22
4.40
5.26
6.16
6.16
6.32
8.21
8.43
5.4
4.2
5.6
8.3
5.2
5.4
3.9
3.0
3.1
5.2
7.1
4.2
3.1
3.1
4.4
3.2
60
60
60
60
60
60
60
60
60
60
60
90
90
90
90
90
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
No. of
Flutes
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
s
s
Type
2
2
2
2
3
3
2
2
3
3
3
2
2
3
2
3
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
Stock
Unit : mm
I136
CUTTING CONDITIONS
I236
VC2C
(<30HRC)
( < 45HRC)
e0.02
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
h6
D4 = 6
8 < D4 < 10
D4 = 12
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
CARBIDE
UWC
Type 2
SQUARE
Type 1
a Chamfer cutter for machining hardened steels and difcult-to-cut
Length of
Cut
ap
Neck
Length
L3
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D2
Small
Mill Dia.
D1
Stock
Dia.
2
4
6
8
10
12
0.3
0.3
0.3
0.4
0.5
0.5
0.85
1.85
2.85
3.8
4.75
5.75
6
12

50
50
50
60
70
75
6
6
6
8
10
12
2
2
2
2
2
2
s
s
s
s
s
s
1
1
2
2
2
2
TAPER
VC2CD0200
D0400
D0600
D0800
D1000
D1200
Type
SOLID END MILLS
Order Number
RADIUS
Unit : mm
BALL
materials.
CUTTING CONDITIONS
I238
I137
IMPACT MIRACLE END MILLS
VF2XL
End mill, 2 ute, Long neck
Carbon Steel, Alloy Steel Pre-Hardened Steel
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
Copper Alloy
D5
CARBIDE
0 -0.020
0 - 0.008
Aluminum Alloy
D1
12
D4(h6)
Type1
ap
SQUARE
L3
L1
UWC
VF
30
D1<3
D1=3
a 2 ute long neck end mill for high-speed machining of
SOLID END MILLS
TAPER
RADIUS
I138
Unit : mm
Dia.
Length of
Cut
Neck
Length
Neck
Dia.
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L3
D5
L1
D4
0.1
0.2
0.2
0.2
0.3
0.3
0.3
0.4
0.4
0.4
0.5
0.5
0.5
0.6
0.6
0.6
0.8
0.8
0.8
0.8
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
0.15
0.3
0.3
0.3
0.5
0.5
0.5
0.6
0.6
0.6
0.8
0.8
0.8
0.9
0.9
0.9
1.2
1.2
1.2
1.2
1.5
1.5
1.5
1.5
1.5
2.3
2.3
2.3
2.3
2.3
3
3
3
3
3
3
0.5
0.6
1
1.5
1
2
3
1
2
4
2
4
6
2
4
6
4
6
8
10
4
6
8
10
12
6
8
10
12
16
6
8
10
12
16
20
0.085
0.17
0.17
0.17
0.27
0.27
0.27
0.36
0.36
0.36
0.46
0.46
0.46
0.56
0.56
0.56
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
1.9
1.9
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
60
50
50
50
50
60
60
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
VF2XLD0010N005
D0020N006
D0020N010
D0020N015
D0030N010
D0030N020
D0030N030
D0040N010
D0040N020
D0040N040
D0050N020
D0050N040
D0050N060
D0060N020
D0060N040
D0060N060
D0080N040
D0080N060
D0080N080
D0080N100
D0100N040
D0100N060
D0100N080
D0100N100
D0100N120
D0150N060
D0150N080
D0150N100
D0150N120
D0150N160
D0200N060
D0200N080
D0200N100
D0200N120
D0200N160
D0200N200
Stock
BALL
hardened steels.
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Dia.
Neck
Length
Neck
Dia.
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L3
D5
L1
D4
3
3
3
4.5
4.5
4.5
12
16
20
2.9
2.9
2.9
50
60
60
6
6
6
2
2
2
s
s
s
CARBIDE
1
1
1
BALL
RADIUS
TAPER
SOLID END MILLS
VF2XLD0300N120
D0300N160
D0300N200
Type
SQUARE
Length of
Cut
Order Number
Stock
Unit : mm
CUTTING CONDITIONS
I239
I139
VF2MV
End mill, Medium cut length, 2 ute, Irregular helix utes
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
0 -0.020
Austenitic
Stainless Steel
4 < D4 < 6
Titanium Alloy
Copper Alloy
0 - 0.008
Aluminum Alloy
D1
15
D4(h6)
Type1
ap
VF
32.5
37.5
Type2
D4(h6)
UWC
D1
SQUARE
L1
ap
L1
a An irregular helix 2 ute square end mill suitable
for high-speed machining of hardened steel.

Dia.
Length of Cut
Overall Length
Shank Dia.
No. of
Flutes
D1
ap
L1
D4
0.5
1
1.5
2
2.5
3
4
5
6
1.3
2.5
3.8
5
6.3
7.5
10
12.5
15
40
40
40
40
40
50
50
50
50
4
4
4
4
4
6
6
6
6
2
2
2
2
2
2
2
2
2
Order Number
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
1
2
SOLID END MILLS
TAPER
RADIUS
VF2MVD0050
D0100
D0150
D0200
D0250
D0300
D0400
D0500
D0600
Stock
BALL
Unit : mm
I140
CUTTING CONDITIONS
I240
VF4MV
u
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Copper Alloy
Aluminum Alloy
CARBIDE
For austenitic stainless steels, titanium and heat-resistant alloys, the VFMHV is recommended.
D1
Titanium Alloy
Austenitic
Stainless Steel
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
D4(h6)
Type1
ap
L1
UWC
VF
SQUARE

(<30HRC)
( < 45HRC)
D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
D1 < 12 0 -0.020
D1 > 12 0 -0.030
35
38
a An irregular helix 4 ute square end mill suitable
Length of Cut
Overall Length
Shank Dia.
No. of
Flutes
D1
ap
L1
D4
6
8
10
12
16
20
15
20
25
30
40
50
50
60
70
90
100
110
6
8
10
12
16
20
4
4
4
4
4
4
a
s
s
s
s
TAPER
1
1
1
1
1
1
SOLID END MILLS
VF4MVD0600
D0800
D1000
D1200
D1600
D2000
Type
RADIUS
Dia.
Order Number
Stock
Unit : mm
BALL
for high-speed machining of hardened steel.
CUTTING CONDITIONS
I241
I141
CARBIDE
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
Aluminum Alloy
D1
15
ap
D1
43
45
VF
D 1<6
ap
42
45
ap
Curved edge
D1 6
a Impact Miracle end mill with irregular helix utes ensures stable
ap
machining of difcult-to-cut materials and with long overhangs.
Type2
Type3
L1
L1
Dia.
Length of Cut
Overall Length
Shank Dia.
No. of
Flutes
D1
ap
L1
D4
2
2.5
3
3.5
4
5
6
6
7
8
8
9
10
10
10
11
12
12
12
13
14
16
18
20
4
5
8
8
11
13
13
13
19
19
19
22
22
22
22
26
26
26
26
26
32
35
42
45
45
45
45
45
45
50
50
70
60
60
80
70
100
70
100
100
110
75
110
110
130
90
150
110
4
4
6
6
6
6
6
6
8
8
8
10
8
10
10
10
10
12
12
12
12
16
16
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Order Number
TAPER
RADIUS
VFMHVD0200
D0250
D0300
D0350
D0400
D0500
D0600
D0600A070
D0700
D0800
D0800A080
D0900
D1000A100S08
D1000
D1000A100
D1100
D1200A110S10
D1200
D1200A110
D1300
D1400A130S12
D1600
D1800A150S16
D2000
Stock
BALL
Unit : mm
SOLID END MILLS
I142
Type1
L1
D1
SQUARE
UWC
D4(h6)
Hardened Steel
( < 55HRC)
D4(h6)

(<30HRC)
( < 45HRC)
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
4D46
8D410
12D416
D4=20
0 -0.02
0 -0.03
D4(h6)
VFMHV
D1 12
D1 > 12
s
s
a
a
a
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
2
2
1
2
2
1
3
2
2
3
3
2
2
3
3
2
3
2
I242
VFMHVCH
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
D1

(<30HRC)
( < 45HRC)
D4 = 16
D4 = 20
0 -0.03 h6
End mill, Medium cut length, 4 ute, Irregular helix utes,

D4(h6)
Type1
ap
UWC
VF
SQUARE
L1
42
45
a Vibration control end mill with multiple internal through coolant holes ensures stable machining
Length of Cut
Overall Length
Shank Dia.
D1
ap
L1
16
20
35
45
90
110
D4
No. of
Flutes
N
Stock
Dia.
16
20
4
4
s
s
1
1
SOLID END MILLS
VFMHVCHD1600
D2000
Type
TAPER
Order Number
RADIUS
Unit : mm
BALL
on difcult-to-cut materials and applications requiring long overhangs.
CUTTING CONDITIONS
I261
I143
VFJHV
End mill, Semi long cut length, 4 ute, Irregular helix utes
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
D4 = 6
8D4 10
12D4 16
D4 = 20
0 -0.02
0 -0.03
Copper Alloy
Aluminum Alloy
D1
CARBIDE
Hardened Steel
( < 55HRC)
D1 12
D1 > 12
D4(h6)
Type1
ap
VF
43.5
45
D16
43
45
Type2
D4(h6)
UWC
D1
SQUARE
L1
ap
D1>6
L1
a Impact Miracle end mill with irregular helix utes ensures stable
machining of difcult-to-cut materials.

a Suitable for deep machining with long axial depth of cut.
Dia.
Length of Cut
Overall Length
Shank Dia.
D1
ap
L1
2
3
4
5
6
8
10
12
16
20
8
12
16
20
24
28
35
40
55
60
60
60
60
60
60
80
90
100
125
140
D4
No. of
Flutes
N
Stock
BALL
Unit : mm
6
6
6
6
6
8
10
12
16
20
4
4
4
4
4
4
4
4
4
4
Order Number
a
a
s
s
s
s
s
s
s
1
1
1
1
2
2
2
2
2
2
SOLID END MILLS
TAPER
RADIUS
VFJHVD0200
D0300
D0400
D0500
D0600
D0800
D1000
D1200
D1600
D2000
Type
I144
CUTTING CONDITIONS
I243
VF6MHV
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
D1
Hardened Steel
( < 55HRC)
D4 = 6
8D410
12D416
D4 = 20
D112 0 -0.02
D1 > 12 0 -0.03
D4(h6)
Type1
ap
UWC
VF
SQUARE
L1
43.5
45
Length of Cut
Overall Length
Shank Dia.
D1
ap
L1
6
8
10
12
16
20
13
19
22
26
32
38
50
60
70
75
90
100
D4
No. of
Flutes
N
Stock
Dia.
6
8
10
12
16
20
6
6
6
6
6
6
s
s
s
s
s
s
1
1
1
1
1
1
SOLID END MILLS
VF6MHVD0600
D0800
D1000
D1200
D1600
D2000
Type
TAPER
Order Number
RADIUS
Unit : mm
BALL
a Newly developed irregular helix 6 ute geometry reduces vibrations and achieves high efciency machining.
a Suitable for machining of difcult-to-cut materials such as stainless steel, titanium alloy and inconel.
CUTTING CONDITIONS
I244
I145
VF6MHVCH
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
0 - 0.011
0 - 0.013
Aluminum Alloy
D1
CARBIDE
D4 = 16
D4 = 20
0 -0.03
End mill, Medium cut length, 6 ute,

D4(h6)
Type1
ap
SQUARE
L1
UWC
VF
43.5
45
Unit : mm
Length of Cut
Overall Length
Shank Dia.
D1
ap
L1
16
20
32
38
90
100
D4
No. of
Flutes
N
Stock
Dia.
16
20
6
6
Order Number
VF6MHVCHD1600
D2000
Type
1
1
SOLID END MILLS
TAPER
RADIUS
BALL
I146
CUTTING CONDITIONS
I261
VF8MHVCH
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
D1

(<30HRC)
( < 45HRC)
D4 = 16
D4 = 20
0 -0.03
End mill, Medium cut length, 8 ute,

Type1
D4(h6)
ap
UWC
VF
SQUARE
L1
44
45
Length of Cut
Overall Length
Shank Dia.
D1
ap
L1
16
20
32
38
90
100
D4
No. of
Flutes
N
Stock
Dia.
16
20
8
8
s
s
1
1
SOLID END MILLS
VF8MHVCHD1600
D2000
Type
TAPER
Order Number
RADIUS
Unit : mm
BALL
CUTTING CONDITIONS
I262
I147
VFSD
End mill, Short cut length, For hardened materials
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
0 -0.02
Austenitic
Stainless Steel
h6
Titanium Alloy
D4 = 6
8 < D4 < 10
D4 = 12
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Aluminum Alloy
SQUARE
Type 1
Type 2
UWC
Unit : mm
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
1
1.5
2
2.5
3
3.5
4
5
6
8
10
12
2
3
4
5
6
7
8
10
12
16
20
24
45
45
45
45
45
45
45
50
50
60
70
75
6
6
6
6
6
6
6
6
6
8
10
12
4
4
4
4
6
6
6
6
6
6
6
6
Order Number
VFSDD0100
D0150
D0200
D0250
D0300
D0350
D0400
D0500
D0600
D0800
D1000
D1200
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
1
2
2
2
2
SOLID END MILLS
TAPER
RADIUS
BALL
a End mills with Impact Miracle coating for high hardness materials.
I148
CUTTING CONDITIONS
I245
VFMD
End mill, Medium cut length, For hardened materials
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
D1 < 12
D1 > 12
Austenitic
Stainless Steel
0 -0.02
0 -0.03
D4 = 6
8 < D4 < 10
12 < D4 < 16
20 < D4 < 25
h6
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
Type 2
UWC
VFMDD0100
D0150
D0200
D0250
D0300
D0400
D0500
D0600
D0800
D1000
D1200
D1400
D1500
D1600
D1800
D2000
D2200
D2500
1
1.5
2
2.5
3
4
5
6
8
10
12
14
15
16
18
20
22
25
3.5
5
7
8
10
12
15
15
20
25
30
35
40
40
40
45
45
60
60
60
60
60
60
60
60
60
75
80
100
105
110
110
120
125
135
160
6
6
6
6
6
6
6
6
8
10
12
12
16
16
16
20
20
25
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
2
2
2
2
3
1
2
3
2
3
2
I245
RADIUS
Shank
Dia.
D4
TAPER
Overall
Length
L1
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
SOLID END MILLS
Unit : mm
BALL
Type 3
a End mills with Impact Miracle coating for high hardness materials.
Order Number
SQUARE
Type 1
I149

D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminum Alloy
D1
15
D1
UWC
VF
ap
30
D1< 8
D1 > 8
a Impact Miracle roughing end mills for a wide range of work materials from
ap
Type3
L1
Unit : mm
Dia.
Length of Cut
Overall Length
Shank Dia.
D1
ap
L1
3
4
5
6
7
8
9
10
10
12
12
14
16
18
20
6
8
10
12
17
17
22
22
22
27
27
27
33
33
38
50
50
50
50
60
60
70
90
70
100
75
75
90
90
100
D4
No. of
Flutes
N
Stock
BALL
RADIUS
TAPER
SOLID END MILLS
Type2
L1
carbon and alloy steel, hardened steel and difcult-to-cut materials.
I150
Type1
L1
D1
SQUARE
ap
D4(h6)
CARBIDE
Hardened Steel
( < 55HRC)
D4(h6)

(<30HRC)
( < 45HRC)
D4(h6)
VFSFPR
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
6
6
6
6
8
8
10
8
10
10
12
12
16
16
20
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
Order Number
VFSFPRD0300
D0400
D0500
D0600
D0700
D0800
D0900
D1000S08
D1000
D1200S10
D1200
D1400
D1600
D1800
D2000
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
2
1
2
1
3
2
3
2
3
2
3
2
I246
VFSFPRCH
Roughing end mill, Short cut length, 4 ute, with multiple internal through coolant holes
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminum Alloy
CARBIDE
D1

(<30HRC)
( < 45HRC)
0 - 0.011
0 - 0.013
D4 = 16
D4 = 20
D4(h6)
Type1
ap
UWC
VF
SQUARE
L1
30
a Roughing end mill with multiple internal through coolant holes suitable for
Length of Cut
Overall Length
Shank Dia.
D1
ap
L1
16
20
33
38
90
100
D4
No. of
Flutes
N
Stock
Dia.
16
20
4
4
s
s
1
1
SOLID END MILLS
VFSFPRCHD1600
D2000
Type
TAPER
Order Number
RADIUS
Unit : mm
BALL
difcult-to-cut materials.
CUTTING CONDITIONS
I262
I151
VF6SVRCH
D4 = 16
D4 = 20
Roughing end mill, Short cut length, 6 ute, Irregular helix utes,

(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Aluminum Alloy
D1
CARBIDE
Copper Alloy
D4(h6)
Type1
ap
SQUARE
L1
UWC
VF
0 - 0.011
0 - 0.013
28.5
30
a Roughing end mill with multiple internal through coolant holes suitable for
Unit : mm
Length of Cut
Overall Length
Shank Dia.
D1
ap
L1
16
20
33
38
90
100
D4
No. of
Flutes
N
Stock
Dia.
16
20
6
6
Order Number
VF6SVRCHD1600
D2000
Type
1
1
SOLID END MILLS
TAPER
RADIUS
BALL
difcult-to-cut materials.
I152
CUTTING CONDITIONS
I263
D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
VFMFPR
Roughing end mill, Medium cut length, 4 ute
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
D1
15
ap
D1
L1
VF
Type2
30
D4(h6)
UWC
ap
L1
SQUARE
D4(h6)
Type1
a Impact Miracle roughing end mills suitable for the machining
Overall Length
Shank Dia.
D1
ap
L1
5
6
7
8
9
10
12
16
20
15
17
22
28
28
34
40
48
57
60
60
75
75
100
100
110
125
140
D4
No. of
Flutes
N
6
6
8
8
10
10
12
16
20
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
1
2
1
2
1
2
2
2
2
SOLID END MILLS
VFMFPRD0500
D0600
D0700
D0800
D0900
D1000
D1200
D1600
D2000
Type
RADIUS
Length of Cut
Stock
Dia.
Order Number
TAPER
Unit : mm
BALL
of deep walled components.
CUTTING CONDITIONS
I247
I153
VF2WB
Wide ball nose, Medium neck, 2 ute
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
D5

(<30HRC)
( < 45HRC)
D4 = 6
0.01
Aluminum Alloy
15
D1
220
0 - 0.008
D4(h6)
Type1
L3
SQUARE
L1
UWC
VF
a Ball nose end mill suitable for machining of undercut geometries
Order Number
VF2WBR0100N060
R0150N080
R0200N100
R0300N120
Radius of
Ball Nose
Dia.
Neck
Length
Neck
Dia.
Overall
Length
Shank
Dia.
No. of
Flutes
D1
L3
D5
L1
D4
1
1.5
2
3
2
3
4
6
6
8
10
12
1.6
2.4
3.2
4.8
60
60
60
80
6
6
6
6
2
2
2
2
Stock
Unit : mm
s
s
s
s
Type
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
BALL
and complex geometries using a 5-axis machine.
I154
CUTTING CONDITIONS
I248
VF2SSB
(<30HRC)
( < 45HRC)
D4 = 6
8 < D4 < 10
D4 = 12
0 -0.01
e0.005
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.005
0 - 0.006
0 - 0.008
Aluminum Alloy
CARBIDE
UWC
Type 2
SQUARE
Type 1
a 2 ute ball nose end mills with Impact Miracle coating for
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
1
1.5
2
3
4
5
6
8
10
12
1
1.5
2
3
4
5
6
8
10
12
2
3
4
6
8
10
12
14
18
22
0.94
1.44
1.9
2.9
3.9
4.9
5.85
7.85
9.7
11.7
40
40
45
45
45
50
50
60
70
75
6
6
6
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
2
2
2
2
RADIUS
0.5
0.75
1
1.5
2
2.5
3
4
5
6
Neck
Length
L3
No. of
Flutes
D1
Length of
Cut
ap
TAPER
Dia.
SOLID END MILLS
VF2SSBR0050
R0075
R0100
R0150
R0200
R0250
R0300
R0400
R0500
R0600
Radius of
Ball Nose
R
Stock
Order Number
Unit : mm
BALL
high hardness materials.

a Short shank type suitable for use with a shrink t type holder.
CUTTING CONDITIONS
I249
I155
Austenitic
Stainless Steel
Titanium Alloy
I156
10
ap
15
ap
L3
L1
D1
R
Type 2
L1
ap
L1
Type 3
Type 4
Unit : mm
Order Number
Radius of
Ball Nose
R
Dia.
0.1
0.1
0.15
0.15
0.2
0.2
0.3
0.3
0.4
0.4
0.5
0.5
0.6
0.6
0.7
0.7
0.75
0.75
0.8
0.8
0.9
0.9
1
1
1.25
1.5
1.5
2
2
2.5
3
4
5
6
8
10
VF2SBR0010S04
R0010S06
R0015S04
R0015S06
R0020S04
R0020S06
R0030S04
R0030S06
R0040S04
R0040S06
R0050S04
R0050S06
R0060S04
R0060S06
R0070S04
R0070S06
R0075S04
R0075S06
R0080S04
R0080S06
R0090S04
R0090S06
R0100S04
R0100S06
R0125S06
R0150S03
R0150S06
R0200S04
R0200S06
R0250S06
R0300S06
R0400S08
R0500S10
R0600S12
R0800S16
R1000S20
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
SOLID END MILLS
TAPER
RADIUS
BALL
high hardness materials.
Type 1
L1
20
D5
R
a 2 ute ball nose end mills with Impact Miracle coating for
ap
D5
D1
D1
SQUARE
UWC
Aluminum Alloy
10
R L3
R L3
Copper Alloy
0 - 0.004
0 - 0.005
0 - 0.006
0 - 0.008
0 - 0.011
0 - 0.013
D4(h5)
Hardened Steel
(>55HRC)
D1
CARBIDE
Hardened Steel
( < 55HRC)
D5
(<30HRC)
( < 45HRC)
h6:D4 > 12
D4 = 3
4 < D4 < 6
8 < D4 < 10
D4 = 12
D4 = 16
D4 = 20
D4(h5/h6) D4(h5)
VF2SB
D1 < 12 0 -0.01
D1 > 12 0 -0.02
D4(h5)
h5:D4 < 12
R < 6 e0.005
R > 6 e0.010
0.2
0.2
0.3
0.3
0.4
0.4
0.6
0.6
0.8
0.8
1
1
1.2
1.2
1.4
1.4
1.5
1.5
1.6
1.6
1.8
1.8
2
2
2.5
3
3
4
4
5
6
8
10
12
16
20
0.2
0.2
0.3
0.3
0.4
0.4
0.6
0.6
0.8
0.8
1
1
1.2
1.2
1.4
1.4
1.5
1.5
1.6
1.6
1.8
1.8
2
2
2.5
3
3
4
4
5
12
14
18
22
30
38
0.4
0.4
0.6
0.6
0.8
0.8
1.2
1.2
1.6
1.6
2
2
2.4
2.4
2.8
2.8
3
3
3.2
3.2
3.6
3.6
4
4
5

6

8
10

0.17
0.17
0.27
0.27
0.36
0.36
0.56
0.56
0.76
0.76
0.94
0.94
1.14
1.14
1.34
1.34
1.44
1.44
1.54
1.54
1.74
1.74
1.9
1.9
2.4

2.9

3.9
4.9

45
50
45
50
45
50
45
50
45
50
45
50
45
50
45
50
45
50
45
50
45
50
50
60
60
60
70
60
70
80
80
90
100
110
140
160
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
6
3
6
4
6
6
6
8
10
12
16
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
2
1
2
1
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
3
4
3
3
4
4
4
4
4
4
I249
VF2SDB
(<30HRC)
( < 45HRC)
R < 6.5
R > 6.5
e0.01
D1 < 12
D1 > 12
e0.02
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
D4 = 3
4 < D4 < 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
0 -0.02
0 -0.03
Titanium Alloy
Copper Alloy
0 - 0.006
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
UWC
Type 2
SQUARE
Type 1
a 2 ute long neck ball nose end mills with Impact Miracle coating for high
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
0.5
1
1
1.5
1.5
2
2
2.5
3
4
5
6
8
10
1
2
2
3
3
4
4
5
6
8
10
12
16
20
1
2
2
3
3
4
4
5
12
14
18
22
30
38
2
4
4
6
6
8
8
10
22
27
31
35
50
58
0.94
1.9
1.9
2.9
2.9
3.9
3.9
4.9
5.85
7.85
9.7
11.7
15.5
19.5
45
50
60
60
70
60
70
80
80
90
100
110
140
160
4
4
6
3
6
4
6
6
6
8
10
12
16
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
2
1
2
1
1
2
2
2
2
2
2
I250
RADIUS
Dia.
TAPER
VF2SDBR0050
R0100S04
R0100
R0150S03
R0150
R0200S04
R0200
R0250
R0300
R0400
R0500
R0600
R0800
R1000
Radius of
Ball Nose
R
SOLID END MILLS
Order Number
Stock
Unit : mm
BALL
hardness materials.
I157
VF2SDBL
(<30HRC)
( < 45HRC)
CARBIDE
R < 6.5
R > 6.5
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
e0.01
D1 < 12
D1 > 12
e0.02
Austenitic
Stainless Steel
D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
0 -0.02
0 -0.03
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
SQUARE
Type 1
UWC
Type 2
a 2 ute ball nose end mill with long shank for general use.
Order Number
Radius of
Ball Nose
R
Dia.
0.5
1
1.5
2
2.5
3
4
5
6
8
10
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
1
2
3
4
5
6
8
10
12
16
20
1
2
3
4
5
12
14
18
22
30
38
2
4
6
8
10
22
27
31
35
50
58
0.94
1.9
2.9
3.9
4.9
5.85
7.85
9.7
11.7
15.5
19.5
60
80
90
90
110
120
130
140
140
200
200
6
6
6
6
8
6
8
10
12
16
20
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
2
2
2
2
2
2
SOLID END MILLS
TAPER
RADIUS
VF2SDBLR0050
R0100
R0150
R0200
R0250
R0300
R0400
R0500
R0600
R0800
R1000
Neck
Length
L3
No. of
Flutes
D1
Length of
Cut
ap
Stock
BALL
Unit : mm
I158
s:
Inventory maintained in Japan.
CUTTING CONDITIONS
I250
VF2XLBS
Ball nose, Long neck, 2 ute, Short shank
Copper Alloy
Aluminum Alloy
CARBIDE
D1
B2
D4(h6)
Type1
15
R
30
a 2 ute long neck ball nose end mill for high-speed machining of hardened steel.
a Short shank type suitable for use with a shrink t holder.
L1
Effective
length
VF
SQUARE
L3
Effective length
for inclined angle
UWC
ap
Inclined angle
Order Number
VF2XLBSR0020N010
R0020N020
R0020N030
R0020N040
R0025N040
R0025N060
R0030N020
R0030N030
R0030N040
R0030N060
R0040N040
R0040N060
R0050N030
R0050N040
R0050N060
R0050N080
R0100N060
R0100N080
R0100N100
Radius of
Ball Nose
Dia.
Length of Neck Neck Cutting Edge to Overall Shank No. of

Cut
Length Dia. Shank Angle Length Dia. Flutes
D1
ap
L3
D5
B2
L1
D4
0.2
0.2
0.2
0.2
0.25
0.25
0.3
0.3
0.3
0.3
0.4
0.4
0.5
0.5
0.5
0.5
1
1
1
0.4
0.4
0.4
0.4
0.5
0.5
0.6
0.6
0.6
0.6
0.8
0.8
1
1
1
1
2
2
2
0.32
0.32
0.32
0.32
0.4
0.4
0.48
0.48
0.48
0.48
0.64
0.64
0.8
0.8
0.8
0.8
1.6
1.6
1.6
1
2
3
4
4
6
2
3
4
6
4
6
3
4
6
8
6
8
10
0.36
0.36
0.36
0.36
0.46
0.46
0.56
0.56
0.56
0.56
0.76
0.76
0.94
0.94
0.94
0.94
1.9
1.9
1.9
13.4
11.9
10.7
9.7
9.6
8.1
11.8
10.5
9.5
8.0
9.4
7.8
10.1
9.1
7.5
6.4
6.4
5.3
4.5
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Stock
Unit : mm
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
Effective length
for inclined angle
30'
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.0 1.0 1.1 1.2

2.0 2.1 2.3 2.5
3.1 3.2 3.4 3.7
4.1 4.3 4.6 4.9
4.1 4.3 4.6 4.9
6.2 6.4 6.9 7.4
2.1 2.2 2.3 2.5
3.1 3.3 3.5 3.8
4.2 4.3 4.6 5.0
6.3 6.5 6.9 7.5
4.2 4.3 4.6 5.0
6.3 6.5 6.9 7.5
3.2 3.3 3.6 3.9
4.2 4.4 4.8 5.2
6.3 6.6 7.1 7.7
8.4 8.8 9.4 10.2
6.2 6.5 6.9 7.4
8.3 8.7 9.2 9.9
10.4 10.8 11.5 12.4
CUTTING CONDITIONS
BALL
I251
RADIUS
Titanium Alloy
Austenitic
Stainless Steel
0 - 0.008
TAPER
Hardened Steel
(>55HRC)
D5
Hardened Steel
( < 55HRC)
D4 = 4
SOLID END MILLS

(<30HRC)
( < 45HRC)
0 -0.02
0.007
I159
VF2XLB
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
R < 1 e0.007
R > 1 e0.010
0 -0.02
Austenitic
Stainless Steel
Titanium Alloy
h6
4 < D4 < 6
Copper Alloy
0 - 0.008
Aluminum Alloy
Type 1
Effective
length
SQUARE
Effective length
for inclined angle
UWC
Type 2
a 2 ute long neck ball nose end mills with Impact Miracle coating
for high hardness materials.
VF2XLBR0010N005S04
R0010N005S06
R0010N008S04
R0010N010S04
R0010N010S06
R0010N013S04
R0010N015S04
R0010N015S06
R0010N018S04
R0010N020S04
R0010N025S04
R0015N010S04
R0015N010S06
R0015N013S04
R0015N015S04
R0015N015S06
R0015N018S04
R0015N020S04
R0015N020S06
R0015N025S04
R0015N030S04
R0015N040S04
R0020N010S04
R0020N010S06
R0020N015S04
R0020N015S06
R0020N020S04
R0020N020S06
R0020N025S04
R0020N025S06
R0020N030S04
R0020N030S06
R0020N040S04
R0020N050S04
R0025N015S04
R0025N015S06
R0025N020S04
s:
Radius of Dia. Length Neck Neck Cutting Edge to Overall Shank No. of
Ball Nose
of Cut Length Dia. Shank Angle Length Dia. Flutes
D1
R
ap
L3
B2
L1
D4
D5
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.25
0.25
0.25
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.4
0.4
0.4
0.5
0.5
0.75
1
1
1.25
1.5
1.5
1.75
2
2.5
1
1
1.25
1.5
1.5
1.75
2
2
2.5
3
4
1
1
1.5
1.5
2
2
2.5
2.5
3
3
4
5
1.5
1.5
2
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.46
0.46
0.46
11.5
11.7
11.2
10.9
11.3
10.7
10.4
10.9
10.2
10
9.5
11
11.3
10.7
10.4
10.9
10.2
9.9
10.6
9.5
9.1
8.4
11
11.3
10.4
11
10
10.6
9.5
10.3
9.1
10
8.4
7.8
10.5
11
10
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
6
4
4
6
4
4
6
4
4
4
4
6
4
4
6
4
4
6
4
4
4
4
6
4
6
4
6
4
6
4
6
4
4
4
6
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Type
Order Number
Stock
Unit : mm
BALL
RADIUS
TAPER
SOLID END MILLS
I160
Inclined angle
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Effective length
for inclined angle
30'
0.5
0.5
0.7
1.0
1.0
1.3
1.5
1.5
1.8
2.1
2.6
1.0
1.0
1.3
1.5
1.5
1.8
2.1
2.1
2.6
3.1
4.2
1.0
1.0
1.5
1.5
2.0
2.0
2.6
2.6
3.1
3.1
4.1
5.2
1.5
1.5
2.0
0.5
0.5
0.8
1.1
1.1
1.3
1.6
1.6
1.9
2.2
2.7
1.1
1.1
1.3
1.6
1.6
1.9
2.2
2.2
2.7
3.2
4.3
1.0
1.0
1.6
1.6
2.1
2.1
2.7
2.7
3.2
3.2
4.3
5.4
1.6
1.6
2.1
0.6
0.6
0.9
1.2
1.2
1.5
1.8
1.8
2.1
2.4
3.0
1.2
1.2
1.5
1.8
1.8
2.1
2.4
2.4
3.0
3.6
4.8
1.1
1.1
1.7
1.7
2.3
2.3
2.9
2.9
3.5
3.5
4.7
5.9
1.7
1.7
2.3
0.6
0.6
1.0
1.3
1.3
1.6
2.0
2.0
2.3
2.6
3.3
1.3
1.3
1.6
1.9
1.9
2.3
2.6
2.6
3.3
3.9
5.3
1.2
1.2
1.9
1.9
2.6
2.6
3.2
3.2
3.9
3.9
5.2
6.6
1.9
1.9
2.6
10.6
9.5
9.1
10
8.7
8.3
9.4
7.7
8.9
7.2
8.4
9.9
10.6
9.4
9
9.9
8.6
8.3
9.3
7.6
8.8
7.1
8.4
6.6
6.2
7.6
9.9
10.6
8.9
9.9
8.2
9.3
7.5
7
8.3
6.5
6.1
7.5
5.4
6.8
8.8
9.8
8
9.2
7.3
8.7
6.8
8.2
6.3
5.9
7.4
50
50
50
50
50
50
50
50
50
50
60
50
50
50
50
50
50
50
50
50
50
50
50
50
50
60
50
50
50
50
50
50
50
50
50
50
50
50
50
60
50
50
50
50
50
50
50
50
50
50
50
6
4
4
6
4
4
6
4
6
4
6
4
6
4
4
6
4
4
6
4
6
4
6
4
4
6
4
6
4
6
4
6
4
4
6
4
4
6
4
6
4
6
4
6
4
6
4
6
4
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
2.0 2.1
2.3
2.6
2.6 2.7
2.9
3.2
3.1 3.2
3.5
3.9
3.1 3.2
3.5
3.9
3.6 3.8
4.1
4.5
4.1 4.3
4.7
5.2
4.1 4.3
4.7
5.2
5.2 5.4
5.9
6.5
5.2 5.4
5.9
6.5
6.2 6.5
7.1
7.9
6.2 6.5
7.1
7.9
2.1 2.2
2.4
2.6
2.1 2.2
2.4
2.6
2.6 2.7
3.0
3.3
3.1 3.3
3.6
3.9
3.1 3.3
3.6
3.9
3.6 3.8
4.2
4.6
4.2 4.4
4.8
5.2
4.2 4.4
4.8
5.2
5.2 5.4
6.0
6.6
5.2 5.4
6.0
6.6
6.3 6.5
7.1
7.9
6.3 6.5
7.1
7.9
7.3 7.6
8.3
9.2
8.3 8.7
9.5 10.6
8.3 8.7
9.5 10.6
2.1 2.2
2.3
2.6
2.1 2.2
2.3
2.6
3.1 3.3
3.5
3.9
3.1 3.3
3.5
3.9
4.2 4.3
4.7
5.2
4.2 4.3
4.7
5.2
5.2 5.4
5.9
6.5
6.3 6.5
7.1
7.9
6.3 6.5
7.1
7.9
7.3 7.6
8.3
9.2
8.3 8.7
9.5 10.5
8.3
8.7
9.5 10.5
10.4 10.9 11.9 13.2
10.4 10.9 11.9 13.2
3.2
3.3
3.6
4.0
3.2
3.3
3.6
4.0
4.2
4.4
4.8
5.3
4.2
4.4
4.8
5.3
5.3
5.5
6.0
6.7
5.3
5.5
6.0
6.7
6.3
6.6
7.2
8.0
6.3
6.6
7.2
8.0
7.4
7.7
8.4
9.3
8.4
8.8
9.6 10.6
8.4
8.8
9.6 10.6
CUTTING CONDITIONS
I251
SQUARE
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
BALL
0.4
2
0.4
2.5
0.4
3
0.4
3
0.4
3.5
0.4
4
0.4
4
0.4
5
0.4
5
0.4
6
0.4
6
0.48 2
0.48 2
0.48 2.5
0.48 3
0.48 3
0.48 3.5
0.48 4
0.48 4
0.48 5
0.48 5
0.48 6
0.48 6
0.48 7
0.48 8
0.48 8
0.64 2
0.64 2
0.64 3
0.64 3
0.64 4
0.64 4
0.64 5
0.64 6
0.64 6
0.64 7
0.64 8
0.64 8
0.64 10
0.64 10
0.8
3
0.8
3
0.8
4
0.8
4
0.8
5
0.8
5
0.8
6
0.8
6
0.8
7
0.8
8
0.8
8
RADIUS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
30'
CARBIDE
TAPER
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Effective length
for inclined angle
SOLID END MILLS
VF2XLBR0025N020S06
R0025N025S04
R0025N030S04
R0025N030S06
R0025N035S04
R0025N040S04
R0025N040S06
R0025N050S04
R0025N050S06
R0025N060S04
R0025N060S06
R0030N020S04
R0030N020S06
R0030N025S04
R0030N030S04
R0030N030S06
R0030N035S04
R0030N040S04
R0030N040S06
R0030N050S04
R0030N050S06
R0030N060S04
R0030N060S06
R0030N070S04
R0030N080S04
R0030N080S06
R0040N020S04
R0040N020S06
R0040N030S04
R0040N030S06
R0040N040S04
R0040N040S06
R0040N050S04
R0040N060S04
R0040N060S06
R0040N070S04
R0040N080S04
R0040N080S06
R0040N100S04
R0040N100S06
R0050N030S04
R0050N030S06
R0050N040S04
R0050N040S06
R0050N050S04
R0050N050S06
R0050N060S04
R0050N060S06
R0050N070S04
R0050N080S04
R0050N080S06
Ball Nose
D1
R
ap
L3
B2
L1
D5
D4
Type
Order Number
Stock
Unit : mm
I161
VF2XLB
Order Number
VF2XLBR0050N090S04
R0050N100S04
R0050N100S06
R0050N120S04
R0050N120S06
R0050N140S04
R0050N160S04
R0050N160S06
R0050N180S04
R0050N200S04
R0050N200S06
R0060N060S04
R0060N060S06
R0060N080S04
R0060N080S06
R0060N100S04
R0060N100S06
R0060N120S04
R0060N120S06
R0060N140S04
R0060N160S04
R0060N160S06
R0070N080S04
R0070N120S04
R0070N160S04
R0075N060S04
R0075N060S06
R0075N080S04
R0075N080S06
R0075N100S04
R0075N100S06
R0075N120S04
R0075N120S06
R0075N140S04
R0075N140S06
R0075N160S04
R0075N160S06
R0075N180S04
R0075N200S04
R0075N200S06
R0080N080S04
R0080N120S04
R0080N160S04
R0080N200S04
R0090N080S04
R0090N120S04
R0090N160S04
R0090N200S04
R0100N060S04
R0100N060S06
R0100N080S04
Ball Nose
D1
R
ap
L3
B2
L1
D4
D5
Type
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
Stock
Unit : mm
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.8
0.8
0.8
0.8
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
2
2
2
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
1.12
1.12
1.12
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.28
1.28
1.28
1.28
1.44
1.44
1.44
1.44
1.6
1.6
1.6
9
10
10
12
12
14
16
16
18
20
20
6
6
8
8
10
10
12
12
14
16
16
8
12
16
6
6
8
8
10
10
12
12
14
14
16
16
18
20
20
8
12
16
20
8
12
16
20
6
6
8
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.34
1.34
1.34
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.54
1.54
1.54
1.54
1.74
1.74
1.74
1.74
1.9
1.9
1.9
5.5
5.2
6.7
4.6
6.1
4.2
3.8
5.3
3.5
3.3
4.6
6.6
8.1
5.7
7.3
5
6.6
4.5
6
4
3.7
5.2
5.5
4.3
3.5
6.3
8
5.4
7.2
4.7
6.5
4.2
5.9
3.8
5.4
3.4
5
3.1
2.9
4.3
5.3
4.1
3.3
2.8
5.1
3.9
3.1
2.6
5.8
7.9
4.9
50
50
50
50
60
60
60
70
60
60
70
50
50
50
50
50
50
50
50
60
60
70
50
50
60
50
50
50
50
50
50
50
50
50
50
60
60
60
60
70
50
50
60
60
50
50
60
60
50
50
50
4
4
6
4
6
4
4
6
4
4
6
4
6
4
6
4
6
4
6
4
4
6
4
4
4
4
6
4
6
4
6
4
6
4
6
4
6
4
4
6
4
4
4
4
4
4
4
4
4
6
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Effective length
for inclined angle
30'
9.5
10.5
10.5
12.6
12.6
14.7
16.8
16.8
18.9
21.0
21.0
6.3
6.3
8.4
8.4
10.5
10.5
12.6
12.6
14.7
16.8
16.8
8.4
12.6
16.8
6.3
6.3
8.4
8.4
10.5
10.5
12.6
12.6
14.7
14.7
16.8
16.8
18.9
21.0
21.0
8.4
12.6
16.8
21.0
8.4
12.6
16.8
20.9
6.2
6.2
8.3
9.9
11.0
11.0
13.2
13.2
15.3
17.5
17.5
19.7
21.9
21.9
6.6
6.6
8.8
8.8
11.0
11.0
13.2
13.2
15.3
17.5
17.5
8.8
13.1
17.5
6.6
6.6
8.8
8.8
11.0
11.0
13.1
13.1
15.3
15.3
17.5
17.5
19.7
21.9
21.9
8.8
13.1
17.5
21.9
8.8
13.1
17.5
21.8
6.5
6.5
8.7
10.8
12.0
12.0
14.4
14.4
16.8
19.2
19.2
21.6
24.0
24.0
7.2
7.2
9.6
9.6
12.0
12.0
14.4
14.4
16.8
19.2
19.2
9.6
14.4
19.2
7.2
7.2
9.6
9.6
12.0
12.0
14.4
14.4
16.8
16.8
19.2
19.2
21.6
23.9
23.9
9.6
14.4
19.1
23.9
9.6
14.3
19.1
23.9
7.0
7.0
9.4
12.0
13.3
13.3
15.9
15.9
18.6
21.3
21.3
23.9
26.6
26.6
8.0
8.0
10.6
10.6
13.3
13.3
15.9
15.9
18.6
21.2
21.2
10.6
15.9
21.2
7.9
7.9
10.6
10.6
13.2
13.2
15.9
15.9
18.5
18.5
21.2
21.2
23.8
26.5
10.5
15.9
21.2
10.5
15.8
21.1
7.7
7.7
10.4
* No interference
I162
s:
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.4
2.4
2.4
2.4
2.4
2.4
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
3.4
3.4
3.4
3.4
3.4
3.4
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
6.9
4.2
6.2
3.7
5.6
3.3
5.1
2.9
4.7
2.7
4.4
2.5
4.1
2.3
2
3.5
1.7
3
1.5
5.9
4.6
3.7
3.2
2.8
2.4
6.3
5.5
4.9
4.4
4
3.4
2.8
2.5
2.2
1.9
3.6
3
2.5
2.1
1.9
1.7
4.5
3.9
3.4
3.1
2.6
2.1
1.8
1.6
1.4
1.2
50
50
50
50
50
50
50
60
60
60
60
60
60
60
70
70
70
80
80
60
60
70
70
80
80
60
60
60
60
60
70
70
70
80
90
60
70
70
80
80
90
70
70
70
70
70
70
70
80
90
90
6
4
6
4
6
4
6
4
6
4
6
4
6
4
4
6
4
6
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
8.3
10.4
10.4
12.5
12.5
14.6
14.6
16.7
16.7
18.8
18.8
20.9
20.9
22.9
26.1
26.1
31.3
31.3
36.5
10.4
15.6
20.8
26.1
31.3
36.5
8.3
10.4
12.5
14.6
16.7
20.8
26.1
31.3
36.5
41.7
16.7
20.8
26.0
31.3
36.5
41.7
10.4
12.5
14.6
16.6
20.8
26.0
31.2
36.5
41.7
46.9
8.7
10.9
10.9
13.0
13.0
15.2
15.2
17.4
17.4
19.6
19.6
21.8
21.8
23.9
27.2
27.2
32.6
32.6
38.1
10.8
16.3
21.7
27.2
32.6
38.1
8.6
10.8
13.0
15.2
17.3
21.7
27.2
32.6
38.0
43.5
17.3
21.7
27.1
32.6
38.0
43.5
10.8
12.9
15.1
17.3
21.7
27.1
32.6
38.0
43.5
48.9
9.4
11.8
11.8
14.2
14.2
16.6
16.6
19.0
19.0
21.4
21.4
23.8
23.8
26.2
10.4
13.0
13.0
15.7
15.7
18.3
18.3
21.0
23.6
26.3
*
*
*
29.8 32.9
*
*
*
*
*
11.8 12.9
35.8
17.8
23.8
29.7
35.7
41.7
9.3
11.7
14.1
16.5
18.9
23.7
29.7
35.7
41.7
SQUARE
8
10
10
12
12
14
14
16
16
18
18
20
20
22
25
25
30
30
35
10
15
20
25
30
35
8
10
12
14
16
20
25
30
35
40
16
20
25
30
35
40
10
12
14
16
20
25
30
35
40
45
19.6
26.2
32.9
*
*
10.2
12.9
15.5
18.2
20.8
26.1
*
*
*
*
*
18.9 20.8
BALL
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
2
2
2
2
2
2
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.8
2.8
2.8
2.8
2.8
2.8
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
30'
RADIUS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
3.5
3.5
3.5
3.5
3.5
3.5
4
4
4
4
4
4
4
4
4
4
CARBIDE
TAPER
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.25
1.25
1.25
1.25
1.25
1.25
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.75
1.75
1.75
1.75
1.75
1.75
2
2
2
2
2
2
2
2
2
2
Effective length
for inclined angle
SOLID END MILLS
VF2XLBR0100N080S06
R0100N100S04
R0100N100S06
R0100N120S04
R0100N120S06
R0100N140S04
R0100N140S06
R0100N160S04
R0100N160S06
R0100N180S04
R0100N180S06
R0100N200S04
R0100N200S06
R0100N220S04
R0100N250S04
R0100N250S06
R0100N300S04
R0100N300S06
R0100N350S04
R0125N100S06
R0125N150S06
R0125N200S06
R0125N250S06
R0125N300S06
R0125N350S06
R0150N080S06
R0150N100S06
R0150N120S06
R0150N140S06
R0150N160S06
R0150N200S06
R0150N250S06
R0150N300S06
R0150N350S06
R0150N400S06
R0175N160S06
R0175N200S06
R0175N250S06
R0175N300S06
R0175N350S06
R0175N400S06
R0200N100S06
R0200N120S06
R0200N140S06
R0200N160S06
R0200N200S06
R0200N250S06
R0200N300S06
R0200N350S06
R0200N400S06
R0200N450S06
Ball Nose
D5
B2
ap
L3
L1
D4
D1
R
Type
Order Number
Stock
Unit : mm
23.7
29.6
35.6
*
*
*
* *
* *
11.6 12.7
14.0 15.4
16.4 18.0
18.8 20.7
23.6
29.6
*
*
* *
* *
* *
* *
No interference
CUTTING CONDITIONS
I251
I163
VF2XLB
Ball Nose
D5
ap
L3
L1
D4
B2
R
D1
VF2XLBR0200N500S06
R0250N200S06
R0250N250S06
R0250N300S06
R0250N350S06
R0300N300S06
R0300N400S06
R0300N500S06
2
2.5
2.5
2.5
2.5
3
3
3
4
5
5
5
5
6
6
6
3.2
4
4
4
4
4.8
4.8
4.8
50
20
25
30
35
30
40
50
3.9
4.9
4.9
4.9
4.9
5.85
5.85
5.85
1.1
1.5
1.2
1
0.9

100
70
70
80
80
80
90
100
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
Type
Order Number
1
1
1
1
1
2
2
2
s
s
s
s
s
s
s
Effective length
for inclined angle
30'
52.1 54.3
20.8 21.6
26.0 27.1
31.2
36.4
*
*
*
*
*
*
*
*
*
* *
* *
* *
* *
* *
* *
* *
* *
No interference
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
Stock
Unit : mm
I164
s:
CUTTING CONDITIONS
I251
VF3XB
(<30HRC)
( < 45HRC)
0 -0.02
e0.01
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
D4 = 8
h6
Copper Alloy
0 - 0.008
0 - 0.009
Aluminum Alloy
CARBIDE
VF
Effective length
for inclined angle
30
Effective
length
UWC
SQUARE
Type 1
a 3 ute ball end mill, high rigidity taper neck type.
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
0.4
0.4
0.4
0.9
0.9
0.9
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1.5
1.5
1.5
1.5
1.5
1.5
0.4
0.4
0.4
0.4
0.9
0.9
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.3
1.3
1.3
1.3
1.3
1.3
6
8
12
8
12
16
8
10
12
16
20
25
30
35
8
12
16
20
25
30
35
40
50
60
70
12
16
20
25
30
35
10
15
20
30
15
20
1.5
1.5
1.5
1.5
1.5
1.5
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.8
2.8
2.8
2.8
2.8
2.8
8.9
7.5
5.7
7.6
5.8
4.7
9.6
8.5
7.6
6.3
5.4
4.6
4.0
3.5
9.7
7.7
6.4
5.5
4.7
4.0
3.6
3.2
2.7
2.3
2.0
7.9
6.5
5.6
4.8
4.1
3.7
8.1
6.2
5.0
3.7
6.3
5.1
0.82
0.85
0.91
0.96
1.09
1.22
1.02
1.05
1.08
1.13
1.19
1.26
1.33
1.40
1.12
1.24
1.37
1.50
1.65
1.81
1.97
2.12
2.44
2.75
3.07
1.45
1.66
1.87
2.13
2.39
2.65
1.54
1.61
1.68
1.82
1.82
1.98
60
60
60
60
60
60
60
60
60
70
70
70
80
80
60
60
70
70
70
80
80
80
110
110
110
60
70
70
70
80
80
60
60
70
80
60
70
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
30' 1
6.3 6.6 6.9 7.3

8.4 8.6 9.1 9.5
12.4 12.7 13.4 14.1
8.4 8.9 9.3
12.4 13.1 13.8
16.5 17.3 18.3
8.5 8.8 9.3 9.8
10.5 10.9 11.4 12.1
12.6 13.0 13.6 14.4
16.6 17.1 18.0 18.9
20.6 21.2 22.3 23.5
25.7 26.3 27.7 29.3
30.7 31.5 33.1 35.0
35.7 36.6 38.6 40.7
8.6 9.1 9.6
12.6 13.3 14.1
16.7 17.6 18.5
20.7 21.8 23.0
25.7 27.1 28.6
30.8 32.4 34.2
35.8 37.7 39.8
40.8 43.0 45.4
50.9 53.6
60.9 64.1
71.0 74.7
13.0 13.7
17.1 18.0
21.2 22.4
26.3 27.8
31.5 33.2
36.6 38.6
10.6 10.9 11.4 12.0
15.6 16.0 16.9 17.8
20.6 21.2 22.3 23.5
30.7 31.5 33.1 35.0
15.7 16.5 17.4
20.7 21.8 23.0
RADIUS
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
TAPER
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.75
0.75
0.75
0.75
0.75
0.75
Effective length
for inclined angle
SOLID END MILLS
Dia. Taper Angle Length of Neck Length of Cutting Edge to Neck Overall Shank
One Side
Cut Length Neck Ext. Shank Angle Dia. Length Dia.
B1
ap
D1
D13
L13
L3
B2
L1
D4
Type
VF3XBR0040T0024L006
R0040T0024L008
R0040T0024L012
R0040T0054L008
R0040T0054L012
R0040T0054L016
R0050T0024L008
R0050T0024L010
R0050T0024L012
R0050T0024L016
R0050T0024L020
R0050T0024L025
R0050T0024L030
R0050T0024L035
R0050T0054L008
R0050T0054L012
R0050T0054L016
R0050T0054L020
R0050T0054L025
R0050T0054L030
R0050T0054L035
R0050T0054L040
R0050T0054L050
R0050T0054L060
R0050T0054L070
R0050T0130L012
R0050T0130L016
R0050T0130L020
R0050T0130L025
R0050T0130L030
R0050T0130L035
R0075T0024L010
R0075T0024L015
R0075T0024L020
R0075T0024L030
R0075T0054L015
R0075T0054L020
Radius of
Ball Nose
R
Stock
Order Number
No. of Flutes
Unit : mm
BALL
Inclined angle
*
*
*
* No interference
CUTTING CONDITIONS
I252
I165
VF3XB
VF3XBR0075T0054L030
R0075T0054L040
R0075T0130L015
R0075T0130L020
R0075T0130L030
R0100T0024L016
R0100T0024L020
R0100T0024L025
R0100T0024L030
R0100T0024L035
R0100T0024L040
R0100T0054L020
R0100T0054L025
R0100T0054L030
R0100T0054L035
R0100T0054L040
R0100T0054L050
R0100T0054L060
R0100T0054L070
R0100T0130L025
R0100T0130L030
R0100T0130L035
R0100T0130L040
R0125T0054L020
R0125T0054L030
R0125T0054L040
R0125T0130L020
R0125T0130L030
R0125T0130L040
R0150T0024L020
R0150T0024L025
R0150T0024L030
R0150T0024L040
R0150T0024L050
R0150T0054L020
R0150T0054L030
R0150T0054L040
R0150T0054L050
R0150T0054L060
R0150T0054L070
R0150T0130L040
R0150T0130L050
R0150T0130L060
R0150T0130L070
R0200T0054L030
R0200T0054L040
R0200T0054L050
R0200T0054L060
Radius of
Ball Nose
R
One Side
D13
D4
ap
B2
L13
L3
B1
L1
D1
0.75
0.75
0.75
0.75
0.75
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.25
1.25
1.25
1.25
1.25
1.25
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
0.9
0.9
1.5
1.5
1.5
0.4
0.4
0.4
0.4
0.4
0.4
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1.5
1.5
1.5
1.5
0.9
0.9
0.9
1.5
1.5
1.5
0.4
0.4
0.4
0.4
0.4
0.9
0.9
0.9
0.9
0.9
0.9
1.5
1.5
1.5
1.5
0.9
0.9
0.9
0.9
1.3
1.3
1.3
1.3
1.3
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
30
40
15
20
30
16
20
25
30
35
40
20
25
30
35
40
50
60
70
25
30
35
40
20
30
40
20
30
40
20
25
30
40
50
20
30
40
50
60
70
40
50
60
70
30
40
50
60
2.8
2.8
2.8
2.8
2.8
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
4.5
4.5
4.5
4.5
4.5
4.5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
3.7
3.0
6.4
5.2
3.8
5.5
4.6
3.9
3.4
2.9
2.6
4.7
4.0
3.4
3.0
2.7
2.2
1.9
1.6
4.1
3.5
3.1
2.7
4.3
3.1
2.4
4.4
3.1
2.5
3.8
3.1
2.7
2.1
1.7
3.8
2.7
2.1
1.7
2.3
2.0
2.2
2.8
2.4
2.1
3.5
2.7
2.2
1.9
2.29
2.61
2.08
2.34
2.86
2.07
2.13
2.20
2.27
2.34
2.41
2.42
2.57
2.73
2.89
3.04
3.36
3.67
3.99
3.02
3.28
3.54
3.81
2.89
3.20
3.52
3.21
3.74
4.26
3.11
3.18
3.25
3.39
3.53
3.37
3.69
4.00
4.31
4.63
4.94
4.73
5.26
5.78
6.30
4.65
4.97
5.28
5.60
80
80
60
70
80
70
70
70
80
80
80
70
70
80
80
80
110
110
110
70
80
80
80
60
80
80
60
80
80
60
80
80
80
100
60
80
80
100
110
120
80
110
110
120
90
90
110
110
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
6
8
8
8
8
8
8
8
Type
Order Number
Stock
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
No. of Flutes
Unit : mm
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Effective length
for inclined angle
30' 1
s:
30.8 32.4 34.2

40.8 43.0 45.3
16.1 17.0
21.2 22.4
31.5 33.2
16.7 17.1 18.0 19.0
20.7 21.3 22.3 23.5
25.8 26.4 27.8 29.3
30.8 31.6 33.2 35.0
35.8 36.7 38.6
40.8 41.9 44.0
20.8 21.9 23.0
25.8 27.2 28.6
30.9 32.5 34.2
35.9 37.7 39.8
40.9 43.0
51.0 53.6
61.0
71.1
26.4 27.9
31.6 33.3
36.7 38.7
41.8
20.8 21.9 23.1
30.9 32.5 34.2
40.9 43.1
21.4 22.5
31.6 33.3
41.9
20.7 21.3 22.3 23.5
25.8 26.4 27.7 29.2
30.8 31.6 33.2
40.9 41.9 44.0
50.9 52.2
20.9 21.9 23.0
30.9 32.5
41.0 43.1
51.0
61.1 64.2
71.1 74.8
41.9
52.2
62.4
72.7
30.9 32.5 34.2
41.0 43.0
51.0 53.6
61.1
*
*
*
*
* *
* *
*
*
*
*
*
* *
*
*
* *
*
*
*
*
*
*
I166
*
*
*
*
No interference
35
40
50
60
6.5
6.5
6.5
6.5
2.4
2.2
1.8
1.5
5.80
5.95
6.27
6.58
90
90
110
110
8
8
8
8
3
3
3
3
1
1
1
1
s
s
s

35.9 37.7
41.0 43.0
51.0
61.1
*
*
* *
* *
No interference
SQUARE
3.5
3.5
3.5
3.5
BALL
0.9
0.9
0.9
0.9
RADIUS
5
5
5
5
30' 1
CARBIDE
TAPER
2.5
2.5
2.5
2.5
Effective length
for inclined angle
SOLID END MILLS
VF3XBR0250T0054L035
R0250T0054L040
R0250T0054L050
R0250T0054L060
One Side
B1
ap
D1
D13
L13
L3
B2
L1
D4
Type
Radius of
Ball Nose
R
Stock
Order Number
No. of Flutes
Unit : mm
CUTTING CONDITIONS
I252
I167
VF4MB
D4 = 6 0 - 0.008
8 < D4 < 10 0 - 0.009
D4 = 12 0 - 0.011
0 -0.020
0.01

(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
CARBIDE
Copper Alloy
Aluminum Alloy
D1
15
D4(h6)
Type1
R
ap
VF
30
Type2
R
D4(h6)
UWC
D1
SQUARE
L1
ap
L1
a 4 ute ball nose end mill for high-speed machining of
hardened steel.
Order Number
Dia.
Length of
Cut
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L1
D4
0.5
1
1.5
2
2.5
3
4
5
6
1
2
3
4
5
6
8
10
12
2.5
6
8
8
12
12
14
18
22
50
60
70
70
80
80
90
100
110
6
6
6
6
6
6
8
10
12
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
2
2
2
2
SOLID END MILLS
TAPER
RADIUS
VF4MBR0050
R0100
R0150
R0200
R0250
R0300
R0400
R0500
R0600
Radius of
Ball Nose
Stock
BALL
Unit : mm
I168
CUTTING CONDITIONS
I254
VF4SVB
Ball nose, Short cut length, 4 ute,

Variable curve

(<30HRC)
( < 45HRC)
D1 < 12 0 -0.02
D1 > 12 0 -0.03
R < 6 0.01
R > 6 0.02
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
D4 = 6
8D410
12D416
D4 = 20
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
UWC
VF
SQUARE
Type1
45
a Impact Miracle ball nose end mill with variable curve ensures stable
Length of
Cut
Neck
Length
Neck
Dia.
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L3
D5
L1
D4
3
4
5
6
8
10
6
8
10
12
16
20
9
12
15
18
24
30
15
20
25
30
40
50
5.85
7.85
9.7
11.7
15.5
19.5
50
60
70
75
90
100
6
8
10
12
16
20
4
4
4
4
4
4
s
s
s
s
s
Type
1
1
1
1
1
1
RADIUS
Dia.
TAPER
VF4SVBR0300
R0400
R0500
R0600
R0800
R1000
Radius of
Ball Nose
SOLID END MILLS
Order Number
Stock
Unit : mm
BALL
machining of difcult-to-cut materials.
CUTTING CONDITIONS
I255
I169
Austenitic
Stainless Steel
Titanium Alloy
D1
CARBIDE
Hardened Steel
(>55HRC)
ap
Type2
Type3
15
L3
L1
ap
L3
L1
ap
L1
VFHVRBD0100R02N004
D0100R02N006
D0100R02N008
D0100R02N010
D0100R02N015
D0100R02N020
D0150R03N004
D0150R03N006
D0150R03N010
D0150R03N015
D0150R03N020
D0150R03N025
D0150R03N030
D0200R05N006
D0200R05N010
D0200R05N015
D0200R05N020
D0200R05N025
D0200R05N030
D0200R05N035
D0200R05N040
D0300R05N010
D0300R05N015
D0300R05N020
D0300R05N030
D0300R08N010
D0300R08N015
D0300R08N020
D0300R08N030
D0300R08N040
D0300R08N050
D0400R05N012
D0400R05N020
D0400R05N030
D0400R05N048
D0400R10N012
D0400R10N020
Dia. Corner R Length of Neck Neck Cutting Edge to Overall Shank No. of
Cut
D1
ap
L3
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
0.8
0.8
0.5
0.5
0.5
0.5
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
6
8
10
15
20
4
6
10
15
20
25
30
6
10
15
20
25
30
35
40
10
15
20
30
10
15
20
30
40
50
12
20
30
48
12
20
D5
B2
0.94 10.6
0.94 9.2
0.94 8.2
0.94 7.4
0.94 5.9
0.94 4.9
1.44 10.3
1.44 8.9
1.44 7
1.44 5.5
1.44 4.6
1.44 3.9
1.44 3.4
1.9
8.7
1.9
6.7
1.9
5.2
1.9
4.3
1.9
3.6
1.9
3.1
1.9
2.8
1.9
2.5
2.9
5.6
2.9
4.3
2.9
3.4
2.9
2.5
2.9
5.7
2.9
4.3
2.9
3.5
2.9
2.5
2.9
2
2.9
1.6
3.9
3.8
3.9
2.5
3.9
1.8
3.9
1.2
3.9
3.9
3.9
2.5
L1
D4
60
60
60
60
60
80
60
60
60
60
80
80
80
60
60
60
80
80
80
90
90
60
60
80
80
60
60
80
80
90
90
60
80
80
90
60
80
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Stock
Order Number
s
s
s
s
s
s
s
s
s
s
s
s
s
a
a
s
s
s
s
s
s
s
s
s
s
a
a
s
a
s
s
s
s
s
s
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Effective length
for inclined angle
30'
4.2
6.4
8.5
10.5
15.8
20.9
4.2
6.3
10.5
15.7
20.9
26.1
31.3
6.3
10.5
15.6
20.8
26
31.2
36.3
41.5
10.5
15.6
20.8
31.2
10.4
15.6
20.8
31.1
41.5
51.8
12.5
20.8
31.2
49.8
12.5
20.8
4.5
6.7
8.8
11
16.3
21.7
4.5
6.6
10.9
16.3
21.6
27
32.3
6.5
10.8
16.2
21.5
26.9
32.2
37.6
42.9
10.8
16.2
21.5
32.2
10.8
16.2
21.5
32.2
42.9
53.6
13
21.5
32.2
51.5
12.9
21.5
4.7
7.2
9.5
11.8
17.5
23.3
4.6
7.2
11.8
17.5
23.3
29
34.7
7
11.6
17.4
23.1
28.9
34.6
40.4
46.1
11.6
17.4
23.1
34.6
11.6
17.3
23.1
34.6
5.3
7.7
10.2
12.7
18.9
25.1
5.2
7.7
12.7
18.9
25.1
31.3
37.5
7.5
12.5
18.7
24.9
31.2
37.4
*
I170
Type1
Unit : mm
BALL
RADIUS
Inclined angle
and efcient machining.
TAPER
B2
D1
43
45
a Impact Miracle corner radius end mill for high feed
SOLID END MILLS
Effective
length
SQUARE
Effective length
for inclined angle
VF
Aluminum Alloy
D1
UWC
Copper Alloy
D4(h6)
Hardened Steel
( < 55HRC)
D5

(<30HRC)
( < 45HRC)
D4(h6)
4 ute, Corner radius, Short cut length,

Irregular helix utes
D4(h6)
VFHVRB
D4 = 6 0 - 0.008
8 < D4 < 10 0 - 0.009
12 < D4 < 16 0 - 0.011
D1 < 12 0 -0.02
D1 > 12 0 -0.03
D1 < 10 0.007
D1 > 10 0.01
*
*
12.5
18.7
24.9
12.4
18.7
24.9
*
* *
* *
13.9 15
23.1
*
* *
* *
13.8 14.9
23
No interference
L3
4
6
6
6
6
6
6
6
6
6
6
6
7
8
8
8
8
8
8
8
8
9
10
10
10
10
10
10
10
10
11
12
12
12
12
12
12
12
12
12
12
13
16
16
16
16
16
1
0.5
0.5
1
1
1
1.5
1.5
1.5
1.5
2
2
1.5
0.5
0.5
1
1
2
2
2
2
2
0.5
0.5
1
1
2
2
2
2
2
0.5
0.5
1
1
2
2
2
2
3
3
3
0.5
2
3
3
3
4
9
9
9
9
9
9
9
9
9
9
9
11
12
12
12
12
12
12
12
12
13.5
15
15
15
15
15
15
15
15
16.5
18
18
18
18
18
18
18
18
18
18
19.5
24
24
24
24
24
30
18
30
18
30
54
18
30
42
54
18
30

24
40
24
40
24
40
56
72

30
50
30
50
30
50
70
90

36
60
36
60
36
60
84
108
36
60

42
42
42
80
120
D5
B2
L1
D4
3.9 1.8
5.85
5.85
5.85
5.85
5.85
5.85
5.85
5.85
5.85
5.85
5.85

7.85
7.85
7.85
7.85
7.85
7.85
7.85
7.85

9.7

9.7

9.7

9.7

9.7

9.7

9.7

9.7

11.7

11.7

11.7

11.7

11.7

11.7

11.7

11.7

11.7

11.7

15.5

15.5

15.5

15.5

15.5
80
60
80
60
80
90
60
80
90
90
60
80
80
60
100
60
100
60
100
120
120
100
70
110
70
110
70
110
150
150
110
80
120
80
120
80
120
160
160
80
120
120
100
100
100
140
175
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
a
a
s
s
s
s
s
s
s
s
a
a
a
a
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
a
s
s
s
s
s
s
30'
1
2
2
2
2
2
2
2
2
2
2
2
3
2
2
2
2
2
2
2
2
3
2
2
2
2
2
2
2
2
3
2
2
2
2
2
2
2
2
2
2
3
2
2
2
2
2
31.1 32.2
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* No interference
CUTTING CONDITIONS
I256
SQUARE
ap
CARBIDE
BALL
Effective length
for inclined angle
RADIUS
D1
Type
TAPER
VFHVRBD0400R10N030
D0600R05N018
D0600R05N030
D0600R10N018
D0600R10N030
D0600R10N054
D0600R15N018
D0600R15N030
D0600R15N042
D0600R15N054
D0600R20N018
D0600R20N030
D0700R15
D0800R05N024
D0800R05N040
D0800R10N024
D0800R10N040
D0800R20N024
D0800R20N040
D0800R20N056
D0800R20N072
D0900R20
D1000R05N030
D1000R05N050
D1000R10N030
D1000R10N050
D1000R20N030
D1000R20N050
D1000R20N070
D1000R20N090
D1100R20
D1200R05N036
D1200R05N060
D1200R10N036
D1200R10N060
D1200R20N036
D1200R20N060
D1200R20N084
D1200R20N108
D1200R30N036
D1200R30N060
D1300R30
D1600R05N042
D1600R20N042
D1600R30N042
D1600R30N080
D1600R30N120
Dia. Corner R Length of Neck Neck Cutting Edge to Overall Shank No. of
Cut
SOLID END MILLS
Order Number
Stock
Unit : mm
I171
VFHVRB - Inch sizes

(<30HRC)
( < 45HRC)
CARBIDE
.250" < D4 < .375"

D4 = .500"
0 .0008"
e.0004"
4 ute, Corner radius, Short cut length,

Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - .00035
0 - .00043
Aluminum Alloy
Effective
length
SQUARE
Effective length
for inclined angle
UWC
Inclined angle
a Impact Miracle corner radius end mill for high feed
and efcient machining.
Order Number
.125
.125
.188
.188
.250
.250
.313
.313
.375
.375
.500
.500
.030
.030
.050
.050
.060
.060
.080
.080
.080
.080
.120
.120
.125
.125
.188
.188
.375
.375
.469
.469
.563
.563
.750
.750
.375
.625
.563
.938
.750
1.250
.938
1.563
1.125
1.875
1.500
2.500
SOLID END MILLS
TAPER
RADIUS
VFHVRBD1/8N3DR0.03
D1/8N5DR0.03
D3/16N3DR0.05
D3/16N5DR0.05
D1/4N3DR0.06
D1/4N5DR0.06
D5/16N3DR0.08
D5/16N5DR0.08
D3/8N3DR0.08
D3/8N5DR0.08
D1/2N3DR0.12
D1/2N5DR0.12
D1
L3
L1
D4
D5
B2
R
ap
I172
.1211
.1211
.1835
.1835
.2441
.2441
.3066
.3066
.3691
.3691
.4882
.4822
6.1
4.3
2.9
1.8
2.25
2.25
2.25
2.25
2.25
3.00
3.00
4.00
3.00
4.00
4.00
5.00
.250
.250
.250
.250
.250
.250
.313
.313
.375
.375
.500
.500
4
4
4
4
4
4
4
4
4
4
4
4
Stock
BALL
Unit : inch
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
9.9
16.5
14.9
24.7
*
*
*
*
*
*
*
*
10.3 11
11.9
17.1 18.3 19.8
15.4 16.4
25.6
*
*
*
*
*
*
*
*
*
*
* *
* *
* *
* *
* *
* *
* *
* *
* *
No interference
CUTTING CONDITIONS
I260
Corner radius end mill, Medium cut length, 4 ute,


(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
D1
Hardened Steel
( < 55HRC)
0.015
D4 = 6
8D410
12D416
D4 = 20
0 -0.02
h6
0 -0.03
D4(h6)
Type1
ap
L1
UWC
VF
SQUARE
VFMHVRB
D112
D1 > 12
42
45
a Impact Miracle end mill with irregular helix utes ensures stable machining
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L1
D4
VFMHVRBD0600R050
D0600R100
D0800R050
D0800R100
D1000R050
D1000R100
D1000R200
D1200R050
D1200R100
D1200R200
D1600R100
D1600R200
D1600R300
D2000R100
D2000R200
D2000R300
D2000R400
6
6
8
8
10
10
10
12
12
12
16
16
16
20
20
20
20
0.5
1
0.5
1
0.5
1
2
0.5
1
2
1
2
3
1
2
3
4
13
13
19
19
22
22
22
26
26
26
35
35
35
45
45
45
45
50
50
60
60
70
70
70
75
75
75
90
90
90
110
110
110
110
6
6
8
8
10
10
10
12
12
12
16
16
16
20
20
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I242
RADIUS
Length of
Cut
TAPER
Corner R
SOLID END MILLS
Dia.
Order Number
Stock
Unit : mm
BALL
of difcult-to-cut materials and applications requiring long overhangs.
I173
VFMHVRBCH


(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
0 - 0.011
0 - 0.013
Aluminum Alloy
D1
CARBIDE
D4 = 16
D4 = 20
0 -0.03
0.015
D4(h6)
Type1
ap
SQUARE
L1
UWC
VF
42
45
a Vibration control corner radius end mill with multiple internal through coolant holes ensures stable
Dia.
Corner
Radius
Length of
Cut
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L1
D4
16
16
20
20
1
3
1
3
35
35
45
45
90
90
110
110
16
16
20
20
4
4
4
4
Order Number
VFMHVRBCHD1600R100
D1600R300
D2000R100
D2000R300
Stock
Unit : mm
s
s
s
s
Type
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
BALL
machining on difcult-to-cut materials and applications requiring long overhangs.
I174
CUTTING CONDITIONS
I261
VF6MHVRB


(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
0.015
Austenitic
Stainless Steel
Titanium Alloy,
D4 = 6
8D410
12D416
D4 = 20
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
D1
Hardened Steel
( < 55HRC)
D112 0 -0.02
h6
D1 > 12 0 -0.03
D4(h6)
Type1
ap
UWC
VF
SQUARE
L1
43.5
45
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L1
D1
VF6MHVRBD0600R050
D0600R100
D0800R050
D0800R100
D1000R050
D1000R100
D1200R050
D1200R100
D1600R100
D1600R200
D2000R100
D2000R200
6
6
8
8
10
10
12
12
16
16
20
20
0.5
1
0.5
1
0.5
1
0.5
1
1
2
1
2
13
13
19
19
22
22
26
26
32
32
38
38
50
50
60
60
70
70
75
75
90
90
100
100
6
6
8
8
10
10
12
12
16
16
20
20
6
6
6
6
6
6
6
6
6
6
6
6
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
1
1
1
1
1
1
1
1
1
I244
RADIUS
Length of
Cut
TAPER
Corner R
SOLID END MILLS
Dia.
Order Number
Stock
Unit : mm
BALL
a Newly developed irregular helix 6 ute geometry reduces vibrations and achieves high efciency machining.
a Suitable for machining of difcult-to-cut materials such as stainless steel, titanium alloy and inconel.
I175
VF6MHVRBCH


(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
0 - 0.011
0 - 0.013
Aluminum Alloy
D1
CARBIDE
D4 = 16
D4 = 20
0 -0.03 h6
0.015
D4(h6)
Type 1
ap
SQUARE
L1
UWC
VF
43.5
45
a Vibration control corner radius end mill with multiple internal through coolant holes ensures stable
Dia.
Corner
Radius
Length of
Cut
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L1
D1
16
16
20
20
1
3
1
3
32
32
38
38
90
90
100
100
16
16
20
20
6
6
6
6
Order Number
VF6MHVRBCHD1600R100
D1600R300
D2000R100
D2000R300
Stock
Unit : mm
s
s
s
s
Type
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
BALL
machining on difcult-to-cut materials and applications requiring long overhangs.
I176
CUTTING CONDITIONS
I261
VF8MHVRBCH

Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
D1

(<30HRC)
( < 45HRC)
D4 = 16
D4 = 20
0 -0.03 h6
0.015
D4(h6)
Type1
ap
UWC
VF
SQUARE
L1
44
45
a Vibration control corner radius end mill with multiple internal through coolant holes ensures
Length of
Cut
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L1
D1
16
16
20
20
1
3
1
3
32
32
38
38
90
90
100
100
16
16
20
20
8
8
8
8
s
s
s
s
1
1
1
1
SOLID END MILLS
VF8MHVRBCHD1600R100
D1600R300
D2000R100
D2000R300
Type
RADIUS
Corner
Radius
TAPER
Dia.
Order Number
Stock
Unit : mm
BALL
stable machining on difcult-to-cut materials and applications requiring long overhangs.
CUTTING CONDITIONS
I262
I177
DIAMOND COATED END MILLS
Graphite
GFRP
CFRP
Machineable
Ceramics
D1
15
ap
D4(h6)
CARBIDE
Aluminum Alloy
0 - 0.008
0 - 0.009
0 - 0.011
Type1
D4(h6)
DF4JC
End mill, Semi long cut length, 4 ute, For graphite
D4 = 6
8 < D4 < 10
D4 = 12
0 -0.02
Type2
D1
SQUARE
L1
UWC
30
DF
ap
L1
Helix angle
a 4 ute end mill with original diamond coating
Dia.
Length of
Cut
Overall
Length
Shank Dia.
No. of
Flutes
D1
ap
L1
D4
3
4
6
8
10
12
12
16
24
28
35
36
60
60
60
70
90
110
6
6
6
8
10
12
4
4
4
4
4
4
Order Number
DF4JCD0300
D0400
D0600
D0800
D1000
D1200
Stock
Unit : mm
s
s
s
s
s
s
Type
1
1
2
2
2
2
SOLID END MILLS
TAPER
RADIUS
BALL
for graphite machining.
I178
CUTTING CONDITIONS
I264
DF4XL
End mill, Long neck, 4 ute, For graphite
0 -0.02
Aluminum Alloy
Graphite
GFRP
CFRP
Machineable
Ceramics
4 < D4 < 6
8 < D4 < 10
D4 = 12
0 - 0.008
0 - 0.009
0 - 0.011
CARBIDE
UWC
30
DF
Helix angle
Type2
D 1<3
SQUARE
Type1
D1 3
a 4 ute long neck end mill with original diamond coating
Neck
Dia.
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L3
D5
L1
D4
DF4XLD0100N060
D0100N080
D0100N100
D0150N100
D0150N160
D0200N100
D0200N160
D0200N200
D0300N160
D0300N200
D0300N300
D0400N200
D0400N400
D0600N300
D0800N300
D1000N300
D1200N300
1
1
1
1.5
1.5
2
2
2
3
3
3
4
4
6
8
10
12
1.5
1.5
1.5
2.3
2.3
3
3
3
4.5
4.5
4.5
6
6
9
12
15
18
6
8
10
10
16
10
16
20
16
20
30
20
40
30
30
30
30
0.94
0.94
0.94
1.44
1.44
1.9
1.9
1.9
2.9
2.9
2.9
3.9
3.9
5.85
7.85
9.7
11.7
50
50
50
60
60
60
60
60
70
70
70
80
80
70
90
90
110
4
4
4
4
4
4
4
4
4
4
4
4
4
6
8
10
12
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
CUTTING CONDITIONS
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
I265
RADIUS
Neck
Length
TAPER
Length of
Cut
SOLID END MILLS
Dia.
Order Number
Stock
Unit : mm
BALL
I179
GFRP
CFRP
Machineable
Ceramics
0 - 0.008
0 - 0.009
0 - 0.011
D5
Graphite
D1
CARBIDE
Aluminum Alloy
D4 = 6
8 < D4 < 10
D4 = 12
0.01
D4(h6)
DF2MB
ap
Type1
L3
SQUARE
L1
UWC
30
DF
Helix angle
a 2 ute ball nose end mill with original diamond coating
Radius of
Ball Nose
Dia.
Length of
Cut
Neck
Length
Neck
Dia.
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L3
D5
L1
D4
3
3
4
4
5
5
6
6
6
6
8
8
10
10
12
12
30
30
40
40
50
50
55
55
50
50
60
60
70
70
75
75
5.85
5.85
7.85
7.85
9.7
9.7
11.7
11.7
100
150
110
150
120
180
130
200
6
6
8
8
10
10
12
12
2
2
2
2
2
2
2
2
DF2MBR0300A100
R0300A150
R0400A110
R0400A150
R0500A120
R0500A180
R0600A130
R0600A200
Type
Order Number
Stock
Unit : mm
1
1
1
1
1
1
1
1
s
s
s
s
s
s
s
SOLID END MILLS
TAPER
RADIUS
BALL
I180
CUTTING CONDITIONS
I266
GFRP
CFRP
Machineable
Ceramics
u
B2
0 - 0.008
CARBIDE
30
Helix angle
a 2 ute long neck ball nose end mill with original
D4(h6)
L1
Inclined angle
Type2
ap
L3
D4(h6)
DF
L3
D1
UWC
Effective
length
Effective length
for inclined angle
ap
D5
Type1
12
L1
SQUARE
Graphite
D4=4
D1
Aluminum Alloy
0.01
D5
DF2XLB
D1
ap
L3
D5
B2
L1
D4
0.2
0.2
0.2
0.2
0.2
0.2
0.25
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.75
0.75
0.75
0.75
1
1
1
1
1
1
1
1
1.5
1.5
1.5
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.6
0.6
0.6
0.6
0.6
0.8
0.8
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
3
3
3
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.9
0.9
0.9
0.9
0.9
1.2
1.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2.3
2.3
2.3
2.3
3
3
3
3
3
3
3
3
4.5
4.5
4.5
1
2
3
4
8
12
4
2
4
6
10
16
6
8
4
6
8
10
12
20
30
40
8
10
16
30
8
10
12
16
20
25
40
60
16
25
40
0.36
0.36
0.36
0.36
0.36
0.36
0.46
0.56
0.56
0.56
0.56
0.56
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.9
2.9
2.9
11
10
9.1
8.4
6.4
5.1
8.3
9.9
8.3
7.1
5.5
4.1
7
6.1
8
6.8
5.9
5.2
4.6
3.3
2.4
1.9
5.4
4.7
3.4
2.1
4.9
4.2
3.7
2.9
2.5
2
1.4
0.9
1.7
1.2
0.7
50
50
50
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
80
80
80
60
60
80
80
60
60
60
80
80
80
100
100
80
80
100
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Neck
Dia.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Effective length
for inclined angle
30'
1
2
3.1
4.1
8.3
12.5
4.1
2.1
4.2
6.3
10.4
16.7
6.3
8.3
4.2
6.3
8.4
10.5
12.6
21
31.4
41.8
8.4
10.5
16.8
31.4
8.3
10.4
12.5
16.7
20.9
26
41.5
62.6
16.7
26.1
41.7
1
2.1
3.2
4.3
8.7
13
4.3
2.2
4.4
6.5
10.9
17.4
6.5
8.7
4.4
6.6
8.8
11
13.2
21.9
32.8
43.7
8.8
11
17.5
32.8
8.7
10.9
13
17.4
21.8
27.2
43.5
1.1
2.3
3.5
4.7
9.5
14.3
4.7
2.4
4.8
7.1
11.9
19.1
7.1
9.5
4.8
7.2
9.6
12
14.4
24
36
1.2
2.6
3.9
5.2
10.5
15.8
5.2
2.6
5.2
7.9
13.2
21.2
7.9
10.5
5.3
8
10.6
13.3
15.9
26.6
12
19.2
35.9
9.4
11.8
14.2
19
23.8
13.2
21.2
RADIUS
Length of Neck
Cut
Length
TAPER
Dia.
SOLID END MILLS
DF2XLBR0020N010
R0020N020
R0020N030
R0020N040
R0020N080
R0020N120
R0025N040
R0030N020
R0030N040
R0030N060
R0030N100
R0030N160
R0040N060
R0040N080
R0050N040
R0050N060
R0050N080
R0050N100
R0050N120
R0050N200
R0050N300
R0050N400
R0075N080
R0075N100
R0075N160
R0075N300
R0100N080
R0100N100
R0100N120
R0100N160
R0100N200
R0100N250
R0100N400
R0100N600
R0150N160
R0150N250
R0150N400
Cutting Edge to Overall Shank No. of

Shank Angle Length Dia. Flutes
Radius of
Ball Nose
Type
Order Number
Stock
Unit : mm
BALL
diamond coating for graphite machining.
*
*9.6 10.6
*
*
10.4
13
15.7
*
*
* *
* *
*
* *
17.3 *
*
27.2 *
*
*No interference
* *
*
CUTTING CONDITIONS
I267
I181
DF2XLB
DF2XLBR0150N600
R0200N200
R0200N300
R0200N400
R0200N600
Cutting Edge to Overall Shank No. of

Shank Angle Length Dia. Flutes
Radius of
Ball Nose
Dia.
D1
ap
L3
D5
B2
L1
D4
1.5
2
2
2
2
3
4
4
4
4
4.5
6
6
6
6
60
20
30
40
60
2.9
3.9
3.9
3.9
3.9
0.5

100
80
80
100
100
4
4
4
4
4
2
2
2
2
2
Length of Neck
Cut
Length
Neck
Dia.
Type
Order Number
1
2
2
2
2
s
s
s
s
Effective length
for inclined angle
30'
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* No interference
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
Stock
Unit : mm
I182
CUTTING CONDITIONS
I267
DF3XB
Aluminum Alloy
Graphite
GFRP
CFRP
Machineable
Ceramics
D4=6
0.01
0 - 0.008
CARBIDE
coating for graphite machining.
D1
B1
0.5
0.5
0.5
1
1
1
1.5
1.5
2
1
1
1
2
2
2
3
3
4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
ap
L13
L3
B2
D13
L1
D4
1.5
30
1.5
40
1.5
50
3
40
3
60
3
80
4.5
60
4.5
80
6
100
3
3
3
5
5
5
7.5
7.5
9
4
3.2
2.6
2.6
1.8
1.4
1.4
1.1
0.6
0.94
0.94
0.94
1.9
1.9
1.9
2.9
2.9
3.9
100
100
100
100
130
130
130
130
160
6
6
6
6
6
6
6
6
6
3
3
3
3
3
3
3
3
3
1
1
1
1
1
1
1
1
1
s
s
s
s
s
s
s
s
Unit : mm
Effective length
for inclined angle
30' 1
30.4 32.1
40.4 41.4
50.4 51.7
40.7 41.7
60.7 62.2
80.7 82.7
60.8 62.2
80.8 82.8
100.8 *
32.8 34.6
43.6 46
54.4 *
43.9 *
*
*
*
*
*
*
*
*
*
*
* No interference
SOLID END MILLS
Type
DF3XBR0050L030
R0050L040
R0050L050
R0100L040
R0100L060
R0100L080
R0150L060
R0150L080
R0200L100
Radius of Dia. Taper Angle Length of Neck Length of Cutting Edge Neck Overall Shank No. of
One Side
Ball Nose
Cut Length Straight Neck to Shank Dia. Length Dia. Flutes
Angle
Stock
Order Number
Inclined angle
BALL
Helix angle
a 3 ute taper neck ball nose end mill with original diamond
RADIUS
Effective length
for inclined angle
30
TAPER
DF
Effective
length
UWC
SQUARE
Type1
CUTTING CONDITIONS
I268
I183
DFPSRB
Corner radius end mill, Short cut length, 2-4 ute, High precision, For graphite
CARBIDE
Aluminum Alloy
Graphite
GFRP
CFRP
Machineable
Ceramics
0 -0.02
0.01
4 < D4 < 6
8 < D4 < 10
D4 = 12
h6
0 - 0.008
0 - 0.009
0 - 0.011
Type1
Effective length
for inclined angle
UWC
Effective
length
30
DF
Helix angle
D1 < 1.5
a 0.01mm corner radius tolerance, 0-0.02mm outer diameter tolerance. Corner radius
Inclined angle
Unit : mm
Dia.
Order Number
DFPSRBD0050R010N04
D0050R010N05
D0050R010N06
D0050R010N10
D0050R010N15
D0080R010N06
D0080R010N08
D0100R010N08
D0100R010N12
D0100R020N08
D0100R020N12
D0100R020N16
D0100R020N20
D0100R020N30
D0150R020N10
D0150R020N20
D0200R020N12
D0200R020N16
D0200R020N20
D0200R020N30
D0200R020N40
D0300R020N20
D0300R020N40
D0300R050N20
D0400R020N20
D0400R020N40
D0400R050N20
D0400R050N40
D0600R050N30
D0600R100N30
D0800R050N30
D0800R100N30
D1000R050N40
D1000R100N40
D1200R050N40
Corner R Length of Neck

Cut
Length
Neck
Dia.
D1
ap
L3
D5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
1
1
1
1
1
1
1
1.5
1.5
2
2
2
2
2
3
3
3
4
4
4
4
6
6
8
8
10
10
12
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.5
0.2
0.2
0.5
0.5
0.5
1
0.5
1
0.5
1
0.5
0.75
0.75
0.75
0.75
0.75
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2.3
2.3
3
3
3
3
3
4.5
4.5
4.5
6
6
6
6
9
9
12
12
15
15
18
4
5
6
10
15
6
8
8
12
8
12
16
20
30
10
20
12
16
20
30
40
20
40
20
20
40
20
40
30
30
30
30
40
40
40
0.46
0.46
0.46
0.46
0.46
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.9
1.9
1.9
1.9
1.9
2.9
2.9
2.9
3.9
3.9
3.9
3.9
5.85
5.85
7.85
7.85
9.7
9.7
11.7
Cutting Edge Overall Shank No. of

to Shank Length Dia. Flutes
Angle
D4
N
L1
B2
9.5
8.7
8
6.1
4.7
7.7
6.6
6.3
4.9
6.3
4.9
4
3.4
2.5
4.9
2.9
3.7
2.9
2.5
1.7
1.4
1.4
0.7
1.4

60
60
60
60
60
60
60
60
60
60
60
70
70
70
70
70
70
70
80
80
80
80
80
80
80
80
80
80
90
90
90
90
130
130
130
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
8
8
10
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Type
SOLID END MILLS
TAPER
RADIUS
BALL
end mill with original diamond coating for precise and efcient graphite machining.
I184
Type3
D1 > 2
Stock
SQUARE
Type2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Effective length
for inclined angle
30'
4.1
5.2
6.2
10.3
15.5
6.2
8.3
8.5
12.6
8.5
12.6
16.8
20.9
31.3
10.5
20.9
12.5
16.7
20.8
31.2
41.5
20.8
41.5
20.8
4.3
5.4
6.4
10.7
16
6.4
8.6
8.8
13.1
8.8
13.1
17.4
21.7
32.4
11
21.7
13
17.3
21.5
32.2
42.9
21.5
4.6
5.7
6.9
11.5
17.2
6.9
9.2
9.5
14.1
9.5
14.1
18.7
23.3
34.8
11.8
23.3
14
18.6
23.2
5
6.2
7.5
12.4
18.6
7.5
9.9
10.2
15.2
10.2
15.2
20.2
25.1
*
*
*
*
*
*
*
*
*
*
*
12.7
15.1
*
*
* *
* *
* *
* * *
21.5 *
*
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* No interference
CUTTING CONDITIONS
I269
Memo
I185
CBN END MILLS
CBN2XLB
(<30HRC)
( < 45HRC)
CARBIDE
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
e0.005
0 -0.010
Austenitic
Stainless Steel
Titanium Alloy
4 < D4 < 6
Copper Alloy
0 - 0.005
Aluminum Alloy
SQUARE
Type 1
Effective length
for inclined angle
Effective
length
CBN
a Solid CBN ball nose. A wide variation of neck lengths available.
TAPER
RADIUS
CBN2XLBR0020N010S04
R0020N010S06
R0020N016S04
R0020N016S06
R0030N009S06
R0030N015S04
R0030N015S06
R0030N024S04
R0030N024S06
R0040N010S06
R0040N020S04
R0040N020S06
R0040N032S04
R0040N032S06
R0050N011S06
R0050N025S04
R0050N025S06
R0050N040S04
R0050N040S06
R0075N038S04
R0075N038S06
R0075N060S04
R0075N060S06
R0100N017S06
R0100N050S04
R0100N050S06
R0100N080S04
R0100N080S06
SOLID END MILLS
I186
Ball Nose
D4
L1
ap
L3
B2
D5
D1
R
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.75
0.75
0.75
0.75
1
1
1
1
1
0.4
0.4
0.4
0.4
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1.5
1.5
1.5
1.5
2
2
2
2
2
0.3
0.3
0.3
0.3
0.4
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
1.1
1.1
1.1
1.1
1.2
1.5
1.5
1.5
1.5
1
1
1.6
1.6
0.9
1.5
1.5
2.4
2.4
1
2
2
3.2
3.2
1.1
2.5
2.5
4
4
3.8
3.8
6
6
1.7
5
5
8
8
0.36
0.36
0.36
0.36
0.56
0.56
0.56
0.56
0.56
0.76
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
1.9
13.4
13.9
12.4
13.3
14.1
12.6
13.4
11.3
12.5
14.1
11.8
12.9
10.3
11.7
14.1
11
12.3
9.3
11
9.1
11
7.1
9.3
13.6
7.3
9.8
5.3
7.9
51
51
51
51
62
51
51
51
51
62
51
51
51
51
62
51
51
51
51
52
52
52
52
62
52
52
52
52
4
6
4
6
6
4
6
4
6
6
4
6
4
6
6
4
6
4
6
4
6
4
6
6
4
6
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Type
Order Number
Stock
BALL
Inclined angle
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
a
s
a
s
s
s
s
s
s
s
s
s
Unit : mm
Effective length
for inclined angle
30'
1
1
1.6
1.6
0.9
1.5
1.5
2.5
2.5
1
2
2
3.3
3.3
1.1
2.6
2.6
4.1
4.1
3.9
3.9
6.2
6.2
1.7
5.1
5.1
8.2
8.2
1
1
1.7
1.7
0.9
1.6
1.6
2.6
2.6
1
2.1
2.1
3.4
3.4
1.1
2.7
2.7
4.3
4.3
4.1
4.1
6.4
6.4
1.7
5.3
5.3
8.5
8.5
1.1
1.1
1.8
1.8
1.0
1.7
1.7
2.7
2.7
1.1
2.3
2.3
3.6
3.6
1.2
2.8
2.8
4.6
4.6
4.3
4.3
6.8
6.8
1.8
5.6
5.6
9
9
1.2
1.2
2
2
1.1
1.8
1.8
2.9
2.9
1.2
2.4
2.4
3.9
3.9
1.2
3
3
4.9
4.9
4.6
4.6
7.3
7.3
1.9
6
6
9.7
9.7
Short edge and neck lengths for high rigidity.
CUTTING CONDITIONS
I270
CBN2XLRB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
e0.005
Austenitic
Stainless Steel
0 - 0.010
Titanium Alloy
Copper Alloy
Aluminum Alloy
CARBIDE
B2
D1
D4
D5
Type 1
15
ap
L3
Effective length
for inclined angle
Effective
length
CBN
SQUARE
L1
D1
ap
L3
D5
B2
L1
D4
0.05
0.05
0.1
0.1
0.05
0.05
0.1
0.1
0.2
0.2
0.3
0.3
0.1
0.1
0.2
0.2
0.3
0.3
0.1
0.1
0.2
0.2
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
0.3
0.3
0.3
0.3
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.9
0.9
0.9
0.9
0.9
0.9
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
2
3
2
3
3
5
3
5
3
5
3
5
5
8
5
8
5
8
6
10
6
10
6
10
6
10
0.46
0.46
0.46
0.46
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
11.6
10.4
11.7
10.5
9.7
7.9
9.7
8
9.8
8
9.9
8.1
7.3
5.6
7.3
5.6
7.4
5.7
5.9
4.2
5.9
4.2
6
4.2
6.1
4.3
51
51
51
51
51
51
51
51
51
51
51
51
52
52
52
52
52
52
52
52
52
52
52
52
52
52
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Effective length
for inclined angle
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
30'
2.1
3.1
2.1
3.1
3.2
5.3
3.2
5.3
3.2
5.3
3.2
5.3
5.3
8.5
5.3
8.5
5.3
8.5
6.3
10.5
6.3
10.5
6.3
10.5
6.3
10.5
2.1
3.2
2.1
3.2
3.4
5.6
3.4
5.6
3.4
5.6
3.4
5.6
5.6
8.8
5.6
8.8
5.6
8.8
6.6
10.9
6.6
10.9
6.6
10.8
6.5
10.8
2.3
3.5
2.3
3.4
3.7
6
3.6
6
3.5
6
3.4
6
6
9.5
6
9.5
6
9.5
7.1
11.7
7.1
11.7
7
11.6
7
11.6
2.5
3.7
2.5
3.7
4
6.5
4
6.5
4
6.5
4
6.5
6.5
10.2
6.5
10.2
6.5
10.2
7.6
12.6
7.6
12.6
7.6
12.6
7.5
12.5
CUTTING CONDITIONS
I271
RADIUS
Unit : mm
TAPER
CBN2XLRBD0050R005N02
D0050R005N03
D0050R010N02
D0050R010N03
D0100R005N03
D0100R005N05
D0100R010N03
D0100R010N05
D0100R020N03
D0100R020N05
D0100R030N03
D0100R030N05
D0150R010N05
D0150R010N08
D0150R020N05
D0150R020N08
D0150R030N05
D0150R030N08
D0200R010N06
D0200R010N10
D0200R020N06
D0200R020N10
D0200R030N06
D0200R030N10
D0200R050N06
D0200R050N10
ball Nose
Stock
Order Number
Inclined angle
SOLID END MILLS
lengths available.
BALL
a CBN long neck radius end mill. A wide variation of neck
I187
UNCOATED CARBIDE END MILLS
C2SA
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
D1 < 12
D1 > 12
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
0 -0.020
0 -0.030
Titanium Alloy
D4 = 6
8 < D4 < 10
12 < D4 < 16
D4 = 20
h6
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Copper Alloy
Aluminum Alloy
CARBIDE
SQUARE
Type 1
UWC
Type 2
I188
Unit : mm
Dia.
Neck
Length
L3
Neck
Dia.
D5
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
SOLID END MILLS
TAPER
RADIUS
BALL
a High efciency machining for aluminum alloys.
3
4
5
6
8
10
10
12
12
12
16
16
16
20
20
6
6
8
8
10
12
12
15
15
15
15
15
15
20
20
12
12
15
16
20
30
35
30
35
40
30
40
45
40
50
2.7
3.7
4.7
5.7
7.4
9.4
9.4
11.4
11.4
11.4
15.4
15.4
15.4
19
19
60
60
60
75
75
75
100
75
100
125
75
100
125
100
125
6
6
6
6
8
10
10
12
12
12
16
16
16
20
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
C2SAD0300N120
D0400N120
D0500N150
D0600N160
D0800N200
D1000N300
D1000N350
D1200N300
D1200N350
D1200N400
D1600N300
D1600N400
D1600N450
D2000N400
D2000N500
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
I272
C3SA
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
D1 < 12
D1 > 12
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
0 -0.020
0 -0.030
Titanium Alloy
8 < D4 < 10
12 < D4 < 16
20 < D4 < 25
h6
0 - 0.009
0 - 0.011
0 - 0.013
Copper Alloy
Aluminum Alloy
CARBIDE
UWC
Type 2
Type 1
Type 2
SQUARE
Type 1
Overall
Length
L1
Shank
Dia.
D4
C3SAD1000A100S08
D1000N300
D1000N350
D1200A150S10
D1200N300
D1200N350
D1200N400
D1600A200S14
D1600N300
D1600N400
D1600N450
D1700A150S16
D1800A200S16
D2000A200S18
D2000N400
D2000N600
D2000N850
D2500N500
D2500N650
D2500N900
D2600A200S25
10
10
10
12
12
12
12
16
16
16
16
17
18
20
20
20
20
25
25
25
26
12
12
12
15
15
15
15
15
15
15
15
18
18
20
20
20
20
20
20
20
20

30
35

30
35
40

30
40
45

40
60
85
50
65
90

9.4
9.4

11.4
11.4
11.4

15.4
15.4
15.4

19
19
19
24
24
24
100
75
100
150
75
100
125
200
75
100
125
150
200
200
100
125
150
100
125
150
200
8
10
10
10
12
12
12
14
16
16
16
16
16
18
20
20
20
25
25
25
25
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
CUTTING CONDITIONS
Type
2
1
1
2
1
1
1
2
1
1
1
2
2
2
1
1
1
1
1
1
2
I272
RADIUS
Neck
Dia.
D5
TAPER
Neck
Length
L3
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
Order Number
SOLID END MILLS
Unit : mm
BALL
I189
UNCOATED CARBIDE END MILLS
C2MHA
2 ute, Medium cut length, Relieved neck
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
D1 < 12
D1 > 12
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
0 -0.020
0 -0.030
D4 = 6
8 < D4 < 10
12 < D4 < 16
20 < D4 < 25
h6
Titanium Alloy
Copper Alloy
0 - 0.008
0 - 0.009
0 - 0.011
0 - 0.013
Aluminum Alloy
CARBIDE
SQUARE
Type 1
Type 2
UWC
Type 3
Unit : mm
Overall
Length
L1
Shank
Dia.
D4
No. of
Flutes
D1
Length of
Cut
ap
Stock
Dia.
3
4
5
6
8
10
12
14
16
20
25
9
12
15
18
20
25
25
32
32
38
38
60
60
60
60
75
75
75
75
100
125
125
6
6
6
6
8
10
12
12
16
20
25
2
2
2
2
2
2
2
2
2
2
2
Order Number
C2MHAD0300
D0400
D0500
D0600
D0800
D1000
D1200
D1400
D1600
D2000
D2500
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
2
2
2
2
3
2
2
2
SOLID END MILLS
TAPER
RADIUS
BALL
I190
CUTTING CONDITIONS
I273
C3SARB
Corner radius, Short cut length, 3 ute, For aluminum alloy
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
0 -0.020
0 -0.030
12 < D4 < 16
20 < D4 < 25
Titanium Alloy,
0 - 0.011
0 - 0.013
Copper Alloy
Aluminum Alloy
CARBIDE
D1
D5
Carbon Steel, Alloy Steel, Cast Iron Tool Steel, Pre-Hardened Steel,Hardened Steel
(<30HRC)
( < 45HRC)
D1 < 12
D1 > 12
a High efciency machining for aluminium alloys.
D4(h6)
Type2
ap
L1
Dia.
Order Number
C3SARBD1200N0300R100
D1200N0300R320
D1200N0400R100
D1200N0400R320
D1600N0450R100
D1600N0450R320
D1600N0700R100
D1600N0700R320
D1800R100
D1800R320
D2000N0600R100
D2000N0600R320
D2000N0600R400
D2000N0850R100
D2000N0850R320
D2000N0850R400
D2500N0650R320
D2500N0650R400
D2500N0650R500
D2500N0900R320
D2500N0900R400
D2500N0900R500
Corner R Length of
Cut
Neck
Length
Neck
Dia.
Overall
Length
Shank
Dia.
No. of
Flutes
D1
ap
L3
D5
L1
D4
12
12
12
12
16
16
16
16
18
18
20
20
20
20
20
20
25
25
25
25
25
25
1
3.2
1
3.2
1
3.2
1
3.2
1
3.2
1
3.2
4
1
3.2
4
3.2
4
5
3.2
4
5
15
15
15
15
15
15
15
15
18
18
20
20
20
20
20
20
20
20
20
20
20
20
30
30
40
40
45
45
70
70

60
60
60
85
85
85
65
65
65
90
90
90
11.4
11.4
11.4
11.4
15.4
15.4
15.4
15.4

18.0
18.0
18.0
18.0
18.0
18.0
23.0
23.0
23.0
23.0
23.0
23.0
75
75
125
125
125
125
150
150
150
150
125
125
125
150
150
150
125
125
125
150
150
150
12
12
12
12
16
16
16
16
16
16
20
20
20
20
20
20
25
25
25
25
25
25
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
CUTTING CONDITIONS
Stock
Unit : mm
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Type
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
I272
SQUARE
37.5
D1
UWC
BALL
L1
RADIUS
L3
TAPER
ap
SOLID END MILLS
D4(h6)
Type1
I191
DIAMOND STAR CUTTING CONDITIONS
APPLICATION CHART
y Square
End Mill, Corner Radius End Mill
DS2SS (Î014), DS2MS (Î015), DS2LS (Î016), DS3SC (Î017), DS3MC (Î018), DS4SC (Î019), DS4MC (Î020),
DS4LC (Î021), DS4MC...CB (Î029), DS4LC...CB (Î030), DS2SRB (Î031), DS2MRB (Î032), DS4SRB (Î033),
DS4MRB (Î034)
.016" .125"
150 250 BHN
IPT
IPT
IPT
IPT
.0002 .0005
.0008 .0015
.0015 .003
.002 .003
.003 .005
.3 .5D
.002 .003
.003
.3 .5D
.05 .2D
Carbon Steel
Steel Alloys
45 HRC
130 350
.0002 .0005
.0008 .0015
.0015 .003
Steel Alloys
45 55 HRC
100 160
.0001 .0004
.0005 .001
.001 .002
.002
.003
300
140 185 BHN
100 300
.0001 .0005
.0008 .0015
.0015 .003
.002 .003
.003 .004
400
180 200 BHN
125 350
.0001 .0005
.0008 .0015
.0015 .003
.002 .003
.003 .004
Heat Resistant
32 43 HRC
100 300
.0001 .0004
.0005 .001
.001 .002
.002
.002
Ti
.3 .5D
.3 .5D
.05 .2D
Gray Cast Iron
180 260 BHN
150 550
.0002 .0005
.0008 .0015
.0015 .003
.002 .003
.003 .005
.3 .5D
Ductile Cast Iron
220 260 BHN
150 550
.0002 .0005
.0008 .0015
.0015 .003
.002 .003
.003 .005
.3 .5D
Aluminum Alloys
180 220 BHN
300 1000
.0002 .0005
.001 .002
.002 .003
.003 .004
.004 .005
.5 1D
Copper Alloys
60 120 BHN
200 500
.0002 .0005
.0008 .0015
.0015 .003
.002 .003
.003 .005
.3 .5D
Plastics
300 1500
.0002 .0005
.001 .002
.002 .003
.003 .004
.004 .005
.5 1D
Titanium
300 350 BHN
70 300
.0003 .0006
.0006 .001
.001 .003
.003 .004
.004 .007
.3 .5D
y STAINLESS
STEEL Square End Mill, Corner Radius End Mill
DS3MHH60 ( Î027 ) , DS6MHH60 ( Î028 ) , DS3SH...SS ( Î038 ) , DS3MH...SS ( Î039 ) , DS5MH...SS ( Î040 ) ,
DS5LH...SS (Î041), DS3SHRB...SS (Î044), DS3MHRB...SS (Î045), DS5SHRB...SS (Î046), DS5MHRB...SS (Î047),
DS3MHHRB (Î048), DS6MHHRB (Î049)
.125"
STAINLESS
STEELS
SOLID END MILLS
IPT
160 500
SFM
STEELS
HRC / BHN
Slottingmax
D.O.C.
NONCAST STAINLESS
FERROUS IRON
STEELS
MATERIAL
.141" .250" .281" .500" .563" .750" .750" 1.250"
.141" .250" .281" .500" .563" .750"
.750"
MATERIAL
HRC / BHN
SFM
IPT
IPT
IPT
IPT
IPT
Slottingmax
D.O.C.
304 316
130 190 BHN
150 300
.0005
.0008 .0015
.0015 .003
.002 .003
.003
.3 .5D
405 410 430
180 200 BHN
200 500
.0005
.0008 .0015
.0015 .003
.002 .003
.003
.3 .5D
405 410 430
30 37 HRC
130 500
.0005
.0008 .0015
.0015 .003
.002 .003
.003
.3 .5D
PH
35 42 HRC
150 200
.0004
.0005 .001
.001 .002
.002
.002
.05 .2D
y ALUMINUM
Square End Mill, Corner Radius End Mill
ALUMINUM
DS2SRB...A (Î035), DS2SRB...NA (Î036), DS3MHR...A (Î037)
.141" .250"
.281" .500"
.563" .750"
.750" 1"
IPT
IPT
IPT
IPT
Slottingmax
D.O.C.
MATERIAL
HRC / BHN
SFM
Aluminum Cast
40 100 BHN
700 1500
.001 .002
.002 .003
.003 .004
.004 .006
.5 1D
Aluminum Alloys
<5% silicon
40 100 BHN
700 1500
.001 .002
.002 .003
.003 .004
.004 .006
.5 1D
Aluminum Alloys
>5% silicon
60 120 BHN
450 1000
.001 .002
.002 .003
.003 .004
.004 .006
.5 1D
decrease speed by 25% when using extra length end mills.

* Please
Speed may be increased by 25% when using stub length end mills.
* When slotting, please decrease speed by 20%.
*
I192
APPLICATION CHART
y Ball
Nose End Mill
DS2SB (Î022), DS2LB (Î023), DS3SB (Î024), DS4SB (Î025), DS4LB (Î026)
NONCAST STAINLESS
STEELS
FERROUS IRON STEELS
.016" .125"
Ti
MATERIAL
HRC / BHN
Carbon Steel
150 250 BHN
.141" .250" .281" .500" .563" .750"
.750" 1"
IPT
IPT
IPT
IPT
IPT
Slottingmax
D.O.C.
160 900
.0001 .0005
.001 .0015
.0015 .003
.003 .005
.005 .006
.1 .25D
SFM
Steel Alloys
45 HRC
160 750
.0001 .0004
.001 .0012
.0012 .003
.003 .005
.005 .006
.1 .25D
Steel Alloys
45 55 HRC
160 600
.0001 .0004
.0008 .0012
.0012 .003
.003 .004
.004 .005
.1 .25D
400
180 200 BHN
160 750
.0001 .0004
.001 .0012
.0012 .003
.003 .005
.005 .006
.1 .25D
Heat Resistant
32 43 HRC
150 400
.0001 .0004
.0008 .0012
.0012 .003
.003 .004
.004 .005
.1 .25D
Gray Cast Iron
180 260 BHN
160 900
.0001 .0005
.001 .0015
.0015 .003
.003 .005
.005 .006
.1 .25D
Ductile Cast Iron
220 260 BHN
160 900
.0001 .0005
.001 .0015
.0015 .003
.003 .005
.005 .006
.1 .25D
Aluminum Alloys
180 220 BHN
300 1500
.0001 .0008
.001 .002
.0015 .004
.004 .006
.006 .008
.2 .5D
Copper Alloys
60 120 BHN
160 900
.0001 .0005
.001 .0015
.0015 .003
.003 .005
.005 .006
.1 .25D
Plastics
300 1500
.0001 .0008
.001 .002
.0015 .004
.004 .006
.006 .008
.2 .5D
Titanium
300 350 BHN
100 300
.0001 .0004
.0008 .0012
.0012 .003
.003 .004
.004 .005
.1 .25D
.750"
y STAINLESS
STEEL Ball Nose End Mill

.125"
STAINLESS
STEELS
MATERIAL
HRC / BHN
SFM
IPT
.141" .250" .281" .500" .563" .750"

IPT
IPT
IPT
IPT
Slottingmax
D.O.C.
304 316
130 190 BHN
250 500
.0003 .0004
.001 .0012
.0012 .003
.003 .005
.004 .005
.1 .25D
405 410 430
180 200 BHN
200 600
.0003 .0004
.001 .0012
.0012 .003
.003 .005
.005 .006
.1 .25D
405 410 430
30 37 HRC
130 500
.0003 .0004
.001 .0012
.0012 .003
.003 .005
.005 .006
.1 .25D
PH
35 42 HRC
150 350
.0003 .0004
.0008 .0012
.0012 .003
.003 .004
.004 .005
.1 .25D
decrease speed by 25% when using extra length end mills.

* Please
Speed may be increased by 25% when using stub length end mills.
* When slotting, please decrease speed by 20%.
*
SOLID END MILLS
DS3SHB...SS (Î042), DS3MHB...SS (Î043)
I193
CUTTING CONDITIONS
MS2SS
End mill, Medium cut length, 2 ute MS2MS
SOLID END MILLS
Work
material
Carbon steel, Cast iron,

Alloy steel, Pre-hardened steel
Hardened steel (45 55HRC)
AISI 1050, AISI No 35 B,

AISI P20, AISI P21 etc.
AISI H13 etc.

Table feed
MS2MRB
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ae, ap (mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ae, ap (mm)
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
2
2.5
3
4
5
6
8
10
12
16
20
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
30000
24000
20000
15000
12000
10000
8000
6400
5400
2400
1900
40
100
200
600
1000
1200
1400
1600
1800
2000
3000
3000
2600
2300
2000
1600
1400
1000
900
820
380
320
1.6
3.9
7.9
23.6
39.4
47.2
55.1
63.0
70.9
78.7
118.1
118.1
102.4
90.6
78.7
63.0
55.1
39.4
35.4
32.3
15.0
12.6
0.001
0.002
0.005
0.01
0.015
0.02
0.02
0.03
0.04
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00
<3
<4
40000
40000
40000
40000
40000
40000
40000
40000
40000
32000
32000
24000
19000
16000
12000
9000
7000
5600
4500
3800
1200
1000
40
100
200
600
960
1200
1400
1600
1600
1600
1900
1900
1600
1400
1200
900
700
550
500
450
100
80
1.6
3.9
7.9
23.6
37.8
47.2
55.1
63.0
63.0
63.0
74.8
74.8
63.0
55.1
47.2
35.4
27.6
21.7
19.7
17.7
3.9
3.1
0.001
0.002
0.005
0.01
0.015
0.02
0.02
0.03
0.04
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
0.40
0.50
0.50
< 0.8
<1
Depth of
cut
D:Dia.
1) If the depth of cut is smaller than this table, feed rate can be increased.
2) In case of slotting with over 3 mm endmill, please reduce revolution to 50 70% of above value, and reduce feed rate to 40 60% of above
value.
3) When drilling, please set the feed rate at 1/3 or below of the above value.
4) If the rigidity of the machine or the workpiece installation is very low, or chattering is generated, please reduce the revolution and the feed
rate proportionately.
I194
MS2SS
I050
MS2MS
I051
MS2MRB
I090
MS2MD
Medium cut length, 2 ute, Strong geometry type
Work
material
Dia.
(mm)
1
1.5
2
2.5
3
4
5
6
8
10
12

Hardened steel (45-55HRC)

AISI H13 etc.

Table feed
(mm/min)
(IPM)
Depth of cut
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
(mm)
40000
40000
30000
24000
20000
15000
12000
10000
8000
6400
5400
2000
3000
3000
2600
2300
2000
1600
1400
1000
900
820
78.7
118.1
118.1
102.4
90.6
78.7
63.0
55.1
39.4
35.4
32.3
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00
32000
32000
24000
19000
16000
12000
9000
7000
5600
4500
3800
1600
1900
1900
1600
1400
1200
900
700
550
500
450
63.0
74.8
74.8
63.0
55.1
47.2
35.4
27.6
21.7
19.7
17.7
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
0.40
0.50
0.50
<Please
Depth of
cut
Table feed
Revolution
(min-1)
refer to the list above for depth of cut.
<Please
D:Dia.
SOLID END MILLS
MS2MD
I053
I195
CUTTING CONDITIONS
MS2JS
Work
material
Dia.
(mm)
SOLID END MILLS
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
2
2.5
3
4
5
6
8
10
12

Alloy steel ( 30HRC)
Alloy steel, Tool steel,

Pre-hardened steel
Austenitic stainless steel,

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.
AISI H13, AISI W1-10,

AISI P21 etc.
AISI 304, AISI 306, Ti-6Al-4V etc.
AISI H13 etc.
Table feed
Revolution
(min-1)
(IPM)
(mm/min)
Revolution
(min-1)
(mm/min)
40000
40000
32000
24000
19000
16000
14000
12000
11000
9500
6400
4800
3800
3400
2700
2300
2000
1500
1300
1100
(40)
(45)
(45)
(45)
(45)
(45)
(45)
(45)
(45)
45 (45)
45 (45)
45 (45)
45 (45)
55 (45)
65 (45)
80 (45)
100 (50)
100 (50)
100 (50)
100 (50)
40000
40000
40000
32000
25000
21000
18000
16000
14000
13000
8500
6400
5100
4200
3400
2900
2500
1900
1600
1300
(40)
(45)
(55)
(60)
(60)
(60)
(60)
(60)
(60)
60 (60)
60 (60)
60 (60)
60 (60)
65 (60)
80 (60)
100 (60)
120 (60)
130 (60)
130 (60)
120 (60)
(1.6)
(1.8)
(2.2)
(2.4)
(2.4)
(2.4)
(2.4)
(2.4)
(2.4)
2.4 (2.4)
2.4 (2.4)
2.4 (2.4)
2.4 (2.4)
2.6 (2.4)
3.1 (2.4)
3.9 (2.4)
4.7 (2.4)
5.1 (2.4)
5.1 (2.4)
4.7 (2.4)
Table feed
(IPM)
(1.6)
(1.8)
(1.8)
(1.8)
(1.8)
(1.8)
(1.8)
(1.8)
(1.8)
1.8 (1.8)
1.8 (1.8)
1.8 (1.8)
1.8 (1.8)
2.2 (1.8)
2.6 (1.8)
3.1 (1.8)
3.9 (2.0)
3.9 (2.0)
3.9 (2.0)
3.9 (2.0)
Table feed
Revolution
(min-1)
(mm/min)
(IPM)
40000
40000
27000
20000
16000
13000
11000
9900
8800
8000
5300
4000
3200
2600
2100 (1600)
1800 (1350)
1500 (1100)
1200 (900)
950 (710)
800 (600)
(35)
(35)
(35)
(35)
(35)
(35)
(35)
(35)
(35)
35 (35)
35 (35)
35 (35)
40 (40)
40 (40)
50 (30)
60 (30)
75 (30)
80 (30)
75 (30)
75 (30)
(1.4)
(1.4)
(1.4)
(1.4)
(1.4)
(1.4)
(1.4)
(1.4)
(1.4)
1.4 (1.4)
1.4 (1.4)
1.4 (1.4)
1.6 (1.6)
1.6 (1.6)
2.0 (1.2)
2.4 (1.2)
3.0 (1.2)
3.1 (1.2)
3.0 (1.2)
3.0 (1.2)
Table feed
Revolution
(IPM)
(min-1)
(mm/min)
40000
32000
21000
16000
13000
11000
9100
8000
7100
6400
4200
3200
2500
2100
1700
1500
1300
1000
800
670

25
25
25
25
25
35
40
50
50
50
50
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(1.0)
(1.0)
(1.0)
(1.0)
(1.0)
(1.0)
(1.0)
(1.0)
(1.0)
1.0 (1.0)
1.0 (1.0)
1.0 (1.0)
1.0 (1.0)
1.0 (1.0)
1.4 (1.0)
1.6 (1.0)
2.0 (1.0)
2.0 (1.0)
2.0 (1.0)
2.0 (1.0)
Depth of
cut
D:Dia.
( ) : Indicates standard revolution and feed rate in slotting.
1) When cutting austenitic stainless steels, the use of water-soluble cutting uid is especially effective.
I196
MS2JS
I054
MS2LS
Slotting
Work
material


Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
Table feed
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ap (mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ap (mm)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
2
2.5
3
4
5
6
8
10
12
40000
40000
40000
40000
33000
28000
25000
22000
20000
13000
10000
9000
8000
6000
4800
4000
3000
2400
2000
400
600
700
800
800
800
800
800
800
800
800
800
800
600
480
400
300
240
200
15.7
23.6
27.6
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
23.6
18.9
15.7
11.8
9.4
7.9
0.001
0.005
0.007
0.01
0.015
0.015
0.02
0.03
0.04
0.10
0.15
0.20
0.20
0.20
0.30
0.30
0.30
0.30
0.30
30000
35000
30000
24000
21000
18000
16000
15000
13000
9000
6700
6000
5200
4000
3200
2600
2000
1600
1300
250
420
420
380
480
480
480
500
500
500
500
500
460
340
280
210
170
140
110
9.8
16.5
16.5
15.0
18.9
18.9
18.9
19.7
19.7
19.7
19.7
19.7
18.1
13.4
11.0
8.3
6.7
5.5
4.3
0.001
0.005
0.007
0.01
0.01
0.015
0.02
0.03
0.04
0.10
0.15
0.20
0.20
0.20
0.20
0.20
0.30
0.30
0.30
SOLID END MILLS
Depth of
cut
D:Dia.
Shoulder milling
Work
material


Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
Table feed
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ae (mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ae (mm)
3
4
5
6
8
10
12
3500
2800
2200
1800
1600
1400
1200
370
370
330
300
270
240
200
14.6
14.6
13.0
11.8
10.6
9.4
7.9
0.05
0.06
0.06
0.06
0.08
0.10
0.10
2600
2100
1700
1500
1100
900
750
250
200
160
140
140
140
120
9.8
7.9
6.3
5.5
5.5
5.5
4.7
0.03
0.03
0.03
0.03
0.04
0.05
0.06
Depth of
cut
D:Dia.
MS2LS
I055
I197
CUTTING CONDITIONS
MS2XL
Work
material
Dia. Neck length

(mm) (mm)
0.2
0.3
0.4
0.5
0.6
0.7
SOLID END MILLS
0.8
0.9
1.2
0.5
1
1
3
9
2
4
12
2
6
10
15
2
6
10
18
2
6
10
4
8
12
24
6
10
15
6
8
12
20
30
6
8
12
20

Work
material

Table feed
(IPM)
Revolution
(min-1)
(mm/min)
40000
40000
40000
40000
22000
40000
40000
17000
40000
40000
25000
14000
40000
40000
25000
12000
40000
40000
11000
40000
40000
25000
10000
40000
35000
9000
40000
40000
30000
15000
8000
40000
40000
25000
6500
600
400
650
500
150
800
800
150
950
700
400
150
950
800
450
150
1000
900
300
1200
1000
400
150
1300
1000
400
1600
1600
1000
400
150
1900
1900
1000
150
23.6
15.7
25.6
19.7
5.9
31.5
31.5
5.9
37.4
27.6
15.7
5.9
37.4
31.5
17.7
5.9
39.4
35.4
11.8
47.2
39.4
15.7
5.9
51.2
39.4
15.7
63.0
63.0
39.4
15.7
5.9
74.8
74.8
39.4
5.9
Depth of cut
(mm)
0.004
0.001
0.007
0.002
0.001
0.007
0.003
0.001
0.01
0.003
0.002
0.001
0.01
0.005
0.003
0.001
0.02
0.01
0.005
0.02
0.01
0.003
0.001
0.02
0.01
0.003
0.04
0.03
0.02
0.005
0.001
0.06
0.04
0.03
0.01
Dia. Neck length

(mm) (mm)
1.5
1.6
2.5
6
10
20
30
45
6
10
16
6
10
16
30
40
60
8
16
20
40
50
8
16
20
40
50
12
20
30
40
50
16
35
60
20
40
60

Table feed
(IPM)
Revolution
(min-1)
(mm/min)
40000
30000
15000
7500
5000
40000
30000
20000
40000
30000
20000
8000
6000
4200
25000
18000
12000
8000
4000
20000
15000
10000
5000
3700
15000
11000
6400
4500
2800
12000
5100
2200
10000
4200
1900
2400
1800
600
300
150
2400
1800
1000
2400
1800
1000
500
250
150
2500
1700
1000
400
150
2000
1400
800
250
150
3000
2200
1200
400
150
2500
750
150
2000
800
150
Depth of cut
(mm)
94.5
70.9
23.6
11.8
5.9
94.5
70.9
39.4
94.5
70.9
39.4
19.7
9.8
5.9
98.4
66.9
39.4
15.7
5.9
78.7
55.1
31.5
9.8
5.9
118.1
86.6
47.2
15.7
5.9
98.4
29.5
5.9
78.7
31.5
5.9
0.10
0.05
0.02
0.005
0.001
0.12
0.07
0.04
0.18
0.10
0.06
0.04
0.01
0.003
0.20
0.10
0.08
0.03
0.015
0.30
0.15
0.10
0.02
0.01
0.30
0.22
0.12
0.05
0.018
0.35
0.15
0.02
0.40
0.20
0.10
2) Cutting conditions may differ considerably due to the overhang, depth of cut, and machine tool conditions. Please use the above table as a
start reference point.
I198
MS2XL
I056
MS2XL6

Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
Work material
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
2.1
2.2
2.3
2.4
2.5
Neck
length
(mm)
0.8
1.5
1
2
1.3
2.5
1.5
3
1.8
3.5
2
4
2.3
4.5
2.5
5
2.8
5.5
3
6
3.3
6.5
3.5
7
3.8
7.5
4
8
4.3
8.5
4.5
9
4.8
9.5
5
10
5.3
10.5
5.5
11
5.8
11.5
6
12
6.3
12.5
Table feed
Revolution
(min-1)
(mm/min)
(IPM)
40000
500 1000
19.7 39.4
40000
500 1000
19.7 39.4
40000
500 1000
19.7 39.4
33000
500 1000
19.7 39.4
29000
500 1000
19.7 39.4
25000
500 1000
19.7 39.4
22000
500 1000
19.7 39.4
20000
500 1000
19.7 39.4
18000
500 1000
19.7 39.4
16000
500 1000
19.7 39.4
15000
500 1000
19.7 39.4
14000
500 1000
19.7 39.4
13000
500 1000
19.7 39.4
12000
500 1000
19.7 39.4
12000
500 1000
19.7 39.4
11000
500 1000
19.7 39.4
10000
500 1000
19.7 39.4
10000
500 1000
19.7 39.4
9800
500 1000
19.7 39.4
9600
500 1000
19.7 39.4
9400
500 1000
19.7 39.4
9200
500 1000
19.7 39.4
9000
500 1000
19.7 39.4
Depth of cut per pass

(mm)
0.01
0.007
0.015
0.01
0.02
0.013
0.03
0.018
0.04
0.025
0.06
0.03
0.08
0.05
0.1
0.07
0.12
0.08
0.12
0.08
0.12
0.08
0.12
0.08
0.15
0.1
0.15
0.1
0.17
0.12
0.17
0.12
0.17
0.12
0.2
0.15
0.2
0.15
0.2
0.15
0.2
0.15
0.25
0.2
0.25
0.2
Table feed
Revolution
(min-1)
(mm/min)
(IPM)
30000
300 800
11.8 31.5
30000
300 800
11.8 31.5
30000
300 800
11.8 31.5
25000
300 800
11.8 31.5
22000
300 800
11.8 31.5
20000
300 800
11.8 31.5
18000
300 800
11.8 31.5
16000
300 800
11.8 31.5
14000
300 800
11.8 31.5
13000
300 800
11.8 31.5
12000
300 800
11.8 31.5
11000
300 800
11.8 31.5
10000
300 800
11.8 31.5
10000
300 800
11.8 31.5
9500
300 800
11.8 31.5
9000
300 800
11.8 31.5
9000
300 800
11.8 31.5
9000
300 800
11.8 31.5
9000
300 800
11.8 31.5
9000
300 800
11.8 31.5
8800
300 800
11.8 31.5
8700
300 800
11.8 31.5
8500
300 800
11.8 31.5

(mm)
0.01
0.007
0.015
0.01
0.02
0.013
0.03
0.018
0.04
0.025
0.06
0.03
0.08
0.05
0.1
0.07
0.12
0.08
0.12
0.08
0.12
0.08
0.12
0.08
0.15
0.1
0.15
0.1
0.17
0.12
0.17
0.12
0.17
0.12
0.2
0.15
0.2
0.15
0.2
0.15
0.2
0.15
0.25
0.2
0.25
0.2
SOLID END MILLS
Dia.
(mm)
MS2XL6
I059
I199
CUTTING CONDITIONS
MS4XL

Work material
Work material
Dia.
(mm)
1.2
1.5
1.8
2.5
SOLID END MILLS
I200

Table feed
Neck length
(mm)
Revolution
(min-1)
(mm/min)
4
8
12
16
6
10
12
16
6
12
16
20
6
12
20
25
6
12
16
20
30
8
25
50
8
16
25
30
40000
36000
20000
10000
40000
36000
20000
12000
40000
32000
16000
10000
40000
32000
12000
7000
40000
32000
24000
12000
5000
32000
9000
2500
25000
18000
12000
7000
3000
2400
1000
500
3000
2400
1200
600
3200
2400
1100
600
3600
2800
1000
600
4000
3200
2400
1200
500
4000
1100
300
3600
2500
1700
800
(IPM)
118.1
94.5
39.4
19.7
118.1
94.5
47.2
23.6
126.0
94.5
43.3
23.6
141.7
110.2
39.4
23.6
157.5
126.0
94.5
47.2
19.7
157.5
43.3
11.8
141.7
98.4
66.9
31.5
Depth of cut
(mm)
0.04
0.03
0.02
0.005
0.05
0.04
0.03
0.01
0.06
0.05
0.03
0.01
0.08
0.06
0.02
0.01
0.1
0.07
0.05
0.03
0.01
0.2
0.04
0.005
0.4
0.2
0.1
0.05
Dia.
(mm)
3.5
10
Table feed
Neck length
(mm)
Revolution
(min-1)
(mm/min)
15
25
35
12
20
30
40
50
16
25
35
50
20
30
40
50
30
50
70
40
60
80
20000
11000
5500
18000
12000
8000
4200
2400
14000
9500
6400
3200
11000
8000
5400
3200
8000
4000
2000
6400
3200
1600
3000
1600
800
3000
2000
1300
700
400
2700
1800
1200
600
2200
1600
1100
640
1600
800
400
1300
640
320
(IPM)
Depth of cut
(mm)
118.1
63.0
31.5
118.1
78.7
51.2
27.6
15.7
106.3
70.9
47.2
23.6
86.6
63.0
43.3
25.2
63.0
31.5
15.7
51.2
25.2
12.6
0.6
0.15
0.06
1
0.5
0.2
0.08
0.03
1
0.5
0.2
0.05
1.2
0.6
0.25
0.15
1.6
0.5
0.2
2
0.6
0.3
2) Cutting conditions may differ considerably due to the overhang, depth of cut, and machine tool conditions. Please use the above table as
a start reference point.
MS4XL
I071
- Inch sizes
MS2XL
Work material
Dia
(inch)
.0156
.0313
.0625
.0938
.1250
.1875
.2500
Neck length
(inch)
Revolution
(min-1)
Table feed
(IPM)
Depth of cut
ap
(inch)
.0938
.1250
.1875
.1875
.2500
.3750
.3750
.5000
.7500
.5625
.7500
1.1250
.7500
1.1250
1.5000
40000
30000
20000
40000
25000
15000
40000
30000
10000
33000
20000
10000
25000
17000
13000
17.0
10.6
5.6
56.7
26.6
10.6
90.7
51.0
10.6
81.8
42.5
14.1
72.4
54.2
55.3
.0002
.0002
.0001
.0008
.0008
.0004
.0028
.0016
.0008
.003
.002
.001
.004
.006
.008
Depth of cut
D:Dia.
SOLID END MILLS
MS2XL
I061
I201
CUTTING CONDITIONS
- Inch sizes
MS4XL
Work material
Dia
(inch)
.0156
.0313
.1250
.1875
.2500
Neck length
(inch)
Revolution
(min-1)
Table feed
(IPM)
Depth of cut
ap
(inch)
.3750
.5000
.7500
.5625
.7500
1.1250
.7500
1.1250
1.5000
40000
30000
10000
33000
20000
10000
25000
17000
13000
121.0
68.0
14.2
109.1
56.6
18.8
96.5
72.2
73.7
.0028
.0016
.0008
.003
.002
.001
.004
.006
.008
Depth of cut
D:Dia.
SOLID END MILLS
I202
MS4XL
I074
MSSHD
MSMHD
y Shoulder Milling
Work
material
Dia.
(mm)
2
3
4
5
6
8
10
12
16
20
25


Pre-hardened steel

Titanium alloy
Hardened steel (4555HRC) Heat resistant alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti-6Al-4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
(min-1) (mm/min) (IPM)
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
15000
11000
8000
6400
5800
4400
3500
2900
2200
1800
1400
550
800
900
1000
1100
1100
1000
1000
800
750
600
21.7
31.5
35.4
39.4
43.3
43.3
39.4
39.4
31.5
29.5
23.6
10000
7400
5600
4500
3700
2800
2200
1900
1400
1100
900
340
500
540
600
640
660
640
640
500
460
400
13.4
19.7
21.3
23.6
25.2
26.0
25.2
25.2
19.7
18.1
15.7
10000
7400
5600
4500
3700
2800
2200
1900
1400
1100
900
320
480
520
580
600
600
560
530
450
440
380
12.6
18.9
20.5
22.8
23.6
23.6
22.0
20.9
17.7
17.3
15.0
6400
4800
3600
2900
2400
1800
1400
1200
900
720
570
160
250
270
300
320
330
320
320
250
230
200
6.3
9.8
10.6
11.8
12.6
13.0
12.6
12.6
9.8
9.1
7.9
4800
4000
3200
2600
2100
1600
1300
1100
800
640
510
100
170
240
240
230
220
200
170
130
100
80
3.9
6.7
9.4
9.4
9.1
8.7
7.9
6.7
5.1
3.9
3.1
Depth of
cut
D:Dia.
Work
material
Dia.
(mm)
2
3
4
5
6
8
10
12
16
20
25


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti-6Al-4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
12000
9000
7200
5800
5000
3700
3000
2500
2000
1600
1300
400
600
720
720
800
800
720
720
600
540
480
15.7
23.6
28.3
28.3
31.5
31.5
28.3
28.3
23.6
21.3
18.9
7000
5300
4000
3200
2700
2000
1600
1300
1000
800
640
200
300
360
360
400
400
360
360
280
250
220
7.9
11.8
14.2
14.2
15.7
15.7
14.2
14.2
11.0
9.8
8.7
7000
5300
4000
3200
2700
2000
1600
1300
1000
800
640
100
150
180
180
200
200
180
180
150
130
120
3.9
5.9
7.1
7.1
7.9
7.9
7.1
7.1
5.9
5.1
4.7
4200
3200
2400
1900
1600
1200
960
800
600
480
380
80
130
140
150
160
170
160
160
130
120
100
3.1
5.1
5.5
5.9
6.3
6.7
6.3
6.3
5.1
4.7
3.9
2300
1900
1400
1100
950
720
570
480
360
290
230
40
70
95
95
95
90
80
70
50
40
35
1.6
2.8
3.7
3.7
3.7
3.5
3.1
2.8
2.0
1.6
1.4
SOLID END MILLS
y Slotting
Depth of
cut
D:Dia.
MSSHD
I062
MSMHD
I063
I203
CUTTING CONDITIONS
MSJHD
y Shoulder milling
Work
material
Dia.
(mm)
2
3
4
5
6
8
10
12
16
20


Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

CUTTING CONDITIONS
AISI P21 etc.
Table feed
Revolution
11000
8000
6200
5000
4200
3200
2500
2100
1600
1200
370
550
620
670
750
780
690
670
570
470
14.6
21.7
24.4
26.4
29.5
30.7
27.2
26.4
22.4
18.5
Table feed
Revolution
7000
5100
4000
3200
2600
2000
1600
1300
1000
800
230
320
350
370
400
420
410
380
320
290
9.1
12.6
13.8
14.6
15.7
16.5
16.1
15.0
12.6
11.4

Titanium alloy
AISI 304, AISI 306,

Ti-6Al-4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
7000
5100
4000
3200
2600
2000
1600
1300
1000
800
210
300
340
360
390
400
380
340
280
260
8.3
11.8
13.4
14.2
15.4
15.7
15.0
13.4
11.0
10.2
5000
3800
3000
2400
2000
1500
1200
1000
750
600
100
190
210
220
220
230
210
190
170
150
3.9
7.5
8.3
8.7
8.7
9.1
8.3
7.5
6.7
5.9
3800
2500
1900
1500
1300
960
760
640
480
380
55
80
110
110
110
100
100
80
65
50
2.2
3.1
4.3
4.3
4.3
3.9
3.9
3.1
2.6
2.0
Depth of
cut
D:Dia.
SOLID END MILLS
I204
MSJHD
I065
MSMHZD
y Drilling
y Shoulder milling
Work
material
Dia.
(mm)
Carbon steel, Cast iron, Alloy steel, Tool steel, Austenitic stainless steel, Heat resistant alloy
Alloy steel (30HRC) Pre-hardened steel
Titanium alloy
AISI 1050, AISI 35,
AISI P20 etc.
AISI H13, AISI W1-10, AISI 304, AISI 306,

Ti-6Al-4V etc.
AISI P21 etc.
Inconel718 etc.
Revolution Table feed Revolution Table feed Revolution Table feed Revolution Table feed
(min-1) (mm/min) (IPM) (min-1) (mm/min) (IPM) (min-1) (mm/min) (IPM) (min-1) (mm/min) (IPM)
1
19000 600 23.6 13000 310 12.2 10000 200 7.9 9500
1.5 14000 600 23.6 9000 310 12.2 7500 210 8.3 6400
11000 600 23.6 7200 310 12.2 6000 210 8.3 4800
2
3
8500 770 30.3 5300 380 15.0 4400 220 8.7 3200
7200 850 33.5 4400 480 18.9 3700 250 9.8 2400
4
6
5300 940 37.0 3200 490 19.3 2700 270 10.6 1600
8
4000 1010 39.8 2400 560 22.0 2000 280 11.0 1200
3200 1000 39.4 1900 480 18.9 1600 300 11.8 950
10
2700 950 37.4 1600 440 17.3 1300 300 11.8 800
12
16
2000 720 28.3 1200 350 13.8 1000 260 10.2 600
1600 600 23.6 1000 290 11.4 800 240 9.4 480
20
65
75
75
100
130
130
120
110
90
70
60
2.6
3.0
3.0
3.9
5.1
5.1
4.7
4.3
3.5
2.8
2.4
Work
material
Dia.
(mm)
Carbon steel, Cast iron, Alloy steel, Tool steel, Austenitic stainless steel,
Titanium alloy
AISI 1050, AISI 35,
AISI P20 etc.

Ti-6Al-4V etc.
AISI P21 etc.
Revolution Table feed Revolution Table feed Revolution Table feed

(min-1) (mm/min) (IPM) (min-1) (mm/min) (IPM) (min-1) (mm/min) (IPM)
1
13000 80 3.1 10000 50 2.0 6000 10
1.5 12000 120 4.7 8000 80 3.1 6000 20
11000 200 7.9 7200 140 5.5 6000 30
2
3
8500 250 9.8 5300 180 7.1 4200 50
7200 300 11.8 4400 210 8.3 3300 60
4
6
5300 300 11.8 3200 210 8.3 2200 70
8
4000 320 12.6 2400 220 8.7 1600 80
3200 340 13.4 1900 240 9.4 1300 70
10
2700 320 12.6 1600 220 8.7 1100 70
12
16
2000 250 9.8 1200 180 7.1 800 55
1600 200 7.9 1000 140 5.5 640 55
20
0.4
0.8
1.2
2.0
2.4
2.8
3.1
2.8
2.8
2.2
2.2
Depth of
cut
Depth of
cut
D:Dia.
D:Dia.
y Slotting
Dia.
(mm)
Carbon steel, Cast iron, Alloy steel, Tool steel, Austenitic stainless steel, Heat resistant alloy
Titanium alloy
AISI 1050, AISI 35,
AISI P20 etc.

AISI P21 etc.
Ti-6Al-4V etc.
Inconel718 etc.
SOLID END MILLS
Work
material
Revolution Table feed Revolution Table feed Revolution Table feed Revolution Table feed
(min-1) (mm/min) (IPM) (min-1) (mm/min) (IPM) (min-1) (mm/min) (IPM) (min-1) (mm/min) (IPM)
1
13000 130 5.1 10000 80 3.1 6000 30 1.2
1.5 12000 250 9.8 8000 150 5.9 6000 60 2.4
2
11000 500 19.7 7200 260 10.2 6000 130 5.1
8500 640 25.2 5300 320 12.6 4200 130 5.1
3
4
7200 650 25.6 4400 370 14.6 3300 140 5.5
5300 720 28.3 3200 380 15.0 2200 140 5.5
6
8
4000 780 30.7 2400 430 16.9 1600 140 5.5
3200 770 30.3 1900 370 14.6 1300 150 5.9
10
2700 730 28.7 1600 340 13.4 1100 150 5.9
12
16
2000 600 23.6 1200 290 11.4 800 130 5.1
1600 500 19.7 1000 240 9.4 640 120 4.7
20
5700
3800
2800
1900
1400
950
720
570
480
360
290
25
30
35
50
70
70
60
50
40
30
25
1.0
1.2
1.4
2.0
2.8
2.8
2.4
2.0
1.6
1.2
1.0
Depth of
cut
D:Dia.
MSMHZD
I066
I205
CUTTING CONDITIONS
- Inch sizes
MSMHZD
y Drilling
y Shoulder milling
Work
material
Dia.
(inch)
.0625
.1250
.1875
.2500
.3125
.3750
.4380
.5000
.5630
.6250
.7500
Alloy steel ( 30HRC) Pre-hardened steel
Titanium alloy
AISI 1050, AISI 35,
AISI P20 etc.

AISI P21 etc.
Ti-6Al-4V etc.

13000 550 21.7 8500 310 12.2 7100 200

8000 770 30.3 5100 380 15.0 4200 220
6300 880 34.6 3800 490 19.3 3200 250
5000 950 37.4 3000 500 19.7 2500 270
4000 1000 39.4 2400 560 22.0 2000 280
3300 1000 39.4 2000 490 19.3 1700 290
2900 970 38.2 1700 450 17.7 1400 300
2500 860 33.9 1500 420 16.5 1300 300
2200 790 31.1 1300 370 14.6 1100 280
2000 720 28.3 1200 350 13.8 1000 260
1700 610 24.0 1000 290 11.4 800 240
7.9
8.7
9.8
10.6
11.0
11.4
11.8
11.8
11.0
10.2
9.4
Depth of
cut
Work
material
Dia.
(inch)
.0625
.1250
.1875
.2500
.3125
.3750
.4380
.5000
.5630
.6250
.7500
Titanium alloy
AISI 1050, AISI 35,
AISI P20 etc.

AISI P21 etc.
Ti-6Al-4V etc.

11000
8000
6300
5000
4000
3300
2900
2500
2200
2000
1700
120
260
300
310
320
330
330
310
270
250
200
4.7
10.2
11.8
12.2
12.6
13.0
13.0
12.2
10.6
9.8
7.9
7600
5000
3800
3000
2400
2000
1700
1500
1300
1200
1000
80
180
210
210
220
240
220
210
180
180
140
3.1
7.1
8.3
8.3
8.7
9.4
8.7
8.3
7.1
7.1
5.5
6000
4000
2700
2000
1600
1300
1100
1000
900
800
700
20
50
60
70
80
70
70
70
60
55
55
0.8
2.0
2.4
2.8
3.1
2.8
2.8
2.8
2.4
2.2
2.2
Depth of
cut
D:Dia.
D:Dia.
y Slotting
SOLID END MILLS
Work
material
Dia.
(inch)
.0625
.1250
.1875
.2500
.3125
.3750
.4380
.5000
.5630
.6250
.7500
Titanium alloy
AISI 1050, AISI 35,
AISI P20 etc.

AISI P21 etc.
Ti-6Al-4V etc.

11000
8000
6300
5000
4000
3300
2900
2500
2200
2000
1700
230
600
660
720
780
740
730
700
630
600
510
9.1
23.6
26.0
28.3
30.7
29.1
28.7
27.6
24.8
23.6
20.1
7600
5000
3800
3000
2400
2000
1700
1500
1300
1200
1000
150
320
360
390
430
380
340
330
300
290
240
5.9
12.6
14.2
15.4
16.9
15.0
13.4
13.0
11.8
11.4
9.4
6000
4000
2700
2000
1600
1300
1100
1000
900
800
700
60
130
140
140
140
150
150
140
140
130
120
2.4
5.1
5.5
5.5
5.5
5.9
5.9
5.5
5.5
5.1
4.7
Depth of
cut
D:Dia.
I206
MSMHZD
I067
MS4SC
Work
material
MS4MC


AISI H13 etc.

Table feed
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ae, ap (mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ae, ap (mm)
1
1.5
2
2.5
3
4
5
6
8
10
12
16
20
40000
40000
30000
24000
20000
15000
12000
10000
8000
6400
5400
2400
1900
3000
4500
4500
3900
3500
3000
2400
2100
1500
1400
1200
550
480
118.1
177.2
177.2
153.5
137.8
118.1
94.5
82.7
59.1
55.1
47.2
21.7
18.9
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00
<3
<4
32000
32000
24000
19000
16000
12000
9000
7000
5600
4500
3800
1200
1000
2400
3600
3600
3000
2700
2400
1800
1500
1100
950
860
120
100
94.5
141.7
141.7
118.1
106.3
94.5
70.9
59.1
43.3
37.4
33.9
4.7
3.9
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
0.40
0.50
0.50
< 0.8
<1
Depth of
cut
2) In case of slotting with over 3 mm endmill, please reduce revolution to 50 70% of above value, and reduce feed rate to 40 60% of above
value.
MS4SC
I068
MS4MC
I069
SOLID END MILLS
D:Dia.
I207
CUTTING CONDITIONS
MS4JC
Work
material


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI H13 etc.
Table feed
Table feed
Table feed
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
1
1.5
2
2.5
3
4
5
6
8
10
12
11100
7400
5600
4500
3700
3000
2600
2300
1700
1400
1200
85
85
85
85
90
110
140
170
180
180
170
3.3
3.3
3.3
3.3
3.5
4.3
5.5
6.7
7.1
7.1
6.7
9500
6400
4800
3800
3400
2700
2300
2000
1500
1300
1100
65
90
90
90
90
90
110
140
140
140
140
2.6
3.5
3.5
3.5
3.5
3.5
4.3
5.5
5.5
5.5
5.5
8000
5300
4000
3200
2600
2100
1800
1500
1200
950
800
50
50
50
55
60
70
85
110
110
110
110
2.0
2.0
2.0
2.2
2.4
2.8
3.3
4.3
4.3
4.3
4.3
6400
4200
3200
2500
2100
1700
1500
1300
1000
800
670
35
35
35
35
35
50
55
70
70
70
70
1.4
1.4
1.4
1.4
1.4
2.0
2.2
2.8
2.8
2.8
2.8
Depth of
cut
SOLID END MILLS
D:Dia.
I208
MS4JC
I070
MS3ES
MS2ES
Work
material


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI H13 etc.
Table feed
Table feed
Table feed
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
3
4
5
6
7
8
10
12
10000
7500
6000
5000
4500
4000
3200
2700
600
600
600
600
560
520
450
410
23.6
23.6
23.6
23.6
22.0
20.5
17.7
16.1
7000
5200
4200
3500
3000
2800
2200
1900
400
400
400
400
360
350
300
270
15.7
15.7
15.7
15.7
14.2
13.8
11.8
10.6
6000
4500
3600
3000
2700
2400
1900
1600
300
300
300
300
280
260
230
210
11.8
11.8
11.8
11.8
11.0
10.2
9.1
8.3
5000
4000
3200
2700
2300
2000
1600
1300
120
120
120
120
110
110
100
100
4.7
4.7
4.7
4.7
4.3
4.3
3.9
3.9
Depth of
cut
D:Dia.
Work
material


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI H13 etc.
Table feed
Table feed
Table feed
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
3
4
5
6
7
8
10
12
14
10000
7500
6000
5000
4500
4000
3200
2700
2300
900
900
900
900
840
780
680
620
550
35.4
35.4
35.4
35.4
33.1
30.7
26.8
24.4
21.7
7000
5200
4200
3500
3000
2800
2200
1900
1600
600
600
600
600
540
520
450
410
350
23.6
23.6
23.6
23.6
21.3
20.5
17.7
16.1
13.8
6000
4500
3600
3000
2700
2400
1900
1600
1400
450
450
450
450
420
390
340
310
280
17.7
17.7
17.7
17.7
16.5
15.4
13.4
12.2
11.0
5000
4000
3200
2700
2300
2000
1600
1300
1200
180
180
180
180
160
160
140
120
120
7.1
7.1
7.1
7.1
6.3
6.3
5.5
4.7
4.7
SOLID END MILLS
MS4EC
Depth of
cut
D:Dia.
MS2ES
I075
MS3ES
I076
MS4EC
I077
I209
CUTTING CONDITIONS
MS2SB
Ball nose end mill, Medium cut length, 2 ute MS2MB
Ball nose end mill, Short cut length, 2 ute
Work
material
R
(mm)
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0.1
0.15
0.2
0.25
0.3
0.4
0.5
0.75
1
1.25
1.5
2
2.5
3
4
5
6
Ball nose taper end mill, Medium cut length, 2 ute


AISI H13 etc.
% >15
% < 15
Table feed
Revolution
Table feed
Revolution
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
32000
25000
21000
16000
13000
9000
40000
40000
40000
40000
40000
40000
40000
40000
39000
33000
27000
20000
16000
13000
10000
8000
6000
300
500
1600
2400
3200
4800
5600
6500
6500
7000
7500
7500
6000
5800
4500
3600
2500
11.8
19.7
63.0
94.5
126.0
189.0
220.5
255.9
255.9
275.6
295.3
295.3
236.2
228.3
177.2
141.7
98.4
250
350
1200
1400
1600
2400
3200
4000
4700
4500
4300
3600
2900
2600
2000
1700
1300
9.8
13.8
47.2
55.1
63.0
94.5
126.0
157.5
185.0
177.2
169.3
141.7
114.2
102.4
78.7
66.9
51.2
% < 15
Depth of
cut ap Revolution
Table feed
(mm)
0.003
0.007
0.02
0.025
0.03
0.05
0.06
0.09
0.11
0.12
0.13
0.15
0.20
0.25
0.30
0.50
0.50
40000
40000
40000
40000
40000
40000
40000
40000
40000
36000
32000
25000
20000
17000
13000
10000
7200
300
500
1300
1900
2500
4000
5600
6500
6500
6500
6000
6000
5400
4700
3600
2900
2000
11.8
19.7
51.2
74.8
98.4
157.5
220.5
255.9
255.9
255.9
236.2
236.2
212.6
185.0
141.7
114.2
78.7
MS2MTB
% >15
Table feed
Revolution
40000
40000
40000
40000
40000
40000
40000
32000
31000
26000
22000
16000
13000
10000
8000
6400
4800
250
350
950
1100
1300
1900
3000
3200
3500
3500
3400
2700
2300
2000
1500
1200
1000
9.8
13.8
37.4
43.3
51.2
74.8
118.1
126.0
137.8
137.8
133.9
106.3
90.6
78.7
59.1
47.2
39.4
Depth of
cut ap
(mm)
0.003
0.007
0.015
0.020
0.025
0.04
0.05
0.08
0.11
0.12
0.13
0.15
0.20
0.25
0.30
0.50
0.50
< 0.2R
Depth of cut
< ap
SOLID END MILLS
R:Radius
I210
1) % is the inclination of the machined surface.

MS2SB
I078
MS2MB
I079
MS2MTB
I107
MS2XLB
Work material
R
(mm)
R 0.1
R 0.15
R 0.2
R 0.25
R 0.3
R 0.4
R 0.5
AISI H13 etc.

Neck
Table feed Depth of cut Revolution Table feed Depth of cut
length Revolution
-1
-1
(mm) (min ) (mm/min) (IPM) ap (mm) (min ) (mm/min) (IPM) ap (mm)
0.5
1
1.5
2
2.5
3
1
1.5
2
2.5
3
4
1
2
3
4
5
6
2
3
4
5
6
7
8
10
2
3
4
5
6
7
8
9
10
11
12
2
3
4
5
6
7
8
10
12
3
4
6
8
50000
50000
40000
40000
40000
30000
50000
50000
50000
40000
40000
30000
50000
50000
50000
40000
40000
30000
50000
50000
45000
45000
36000
32000
32000
26000
50000
50000
44000
37000
37000
35000
35000
30000
30000
22000
22000
50000
50000
50000
35000
35000
30000
30000
30000
22000
40000
40000
35000
30000
400
400
300
200
100
50
600
600
600
400
300
200
1800
1300
900
600
400
200
2500
1500
1200
900
600
400
300
200
3500
3500
2500
1200
1000
750
600
500
500
300
200
4400
4000
4000
2400
2400
1500
1500
700
500
4000
4000
3000
2000
15.7
15.7
11.8
7.9
3.9
2.0
23.6
23.6
23.6
15.7
11.8
7.9
70.9
51.2
35.4
23.6
15.7
7.9
98.4
59.1
47.2
35.4
23.6
15.7
11.8
7.9
137.8
137.8
98.4
47.2
39.4
29.5
23.6
19.7
19.7
11.8
7.9
173.2
157.5
157.5
94.5
94.5
59.1
59.1
27.6
19.7
157.5
157.5
118.1
78.7
0.003
0.002
0.001
0.001
0.001
0.001
0.007
0.005
0.003
0.003
0.002
0.002
0.015
0.01
0.005
0.004
0.003
0.002
0.02
0.015
0.01
0.007
0.006
0.005
0.003
0.002
0.03
0.03
0.02
0.01
0.008
0.008
0.006
0.004
0.003
0.002
0.002
0.04
0.04
0.02
0.02
0.02
0.015
0.01
0.008
0.006
0.05
0.05
0.03
0.02
50000
50000
40000
40000
40000
30000
50000
50000
50000
40000
40000
30000
50000
50000
50000
40000
40000
30000
50000
50000
45000
45000
36000
32000
32000
26000
50000
50000
44000
37000
37000
35000
35000
30000
30000
22000
22000
50000
50000
50000
35000
35000
30000
30000
30000
22000
44000
44000
35000
30000
320
320
240
160
80
40
480
480
480
320
240
160
1400
1000
700
480
320
160
2000
1200
950
700
480
320
240
160
2800
2800
2000
950
800
600
480
400
400
240
160
3500
3200
3200
1900
1900
1200
1200
560
400
3200
3200
2400
1600
12.6
12.6
9.4
6.3
3.1
1.6
18.9
18.9
18.9
12.6
9.4
6.3
55.1
39.4
27.6
18.9
12.6
6.3
78.7
47.2
37.4
27.6
18.9
12.6
9.4
6.3
110.2
110.2
78.7
37.4
31.5
23.6
18.9
15.7
15.7
9.4
6.3
137.8
126.0
126.0
74.8
74.8
47.2
47.2
22.0
15.7
126.0
126.0
94.5
63.0
0.003
0.002
0.001
0.001
0.001
0.001
0.007
0.005
0.003
0.003
0.002
0.002
0.015
0.01
0.005
0.004
0.003
0.002
0.02
0.015
0.01
0.007
0.006
0.005
0.003
0.002
0.03
0.03
0.02
0.01
0.008
0.008
0.006
0.004
0.003
0.002
0.002
0.04
0.04
0.02
0.02
0.02
0.015
0.01
0.008
0.006
0.05
0.05
0.03
0.02
R
(mm)
R 0.5
R 0.6
R 0.75
R1
R 1.5
R2
R 2.5
R3
AISI H13 etc.
Neck
Table feed Depth of cut Revolution Table feed Depth of cut
length Revolution
-1
-1
(mm) (min ) (mm/min) (IPM) ap (mm) (min ) (mm/min) (IPM) ap (mm)
10
12
14
16
18
20
3.6
6
8
10
12
18
24
6
8
10
12
16
20
30
4
6
8
10
12
16
20
25
30
35
8
10
16
20
25
30
35
40
10
20
30
40
50
20
25
30
35
30
50
20000
20000
18000
18000
13000
13000
40000
40000
40000
27000
16000
15000
11000
40000
40000
40000
32000
15000
12000
9000
40000
40000
40000
40000
40000
32000
10000
10000
10000
10000
32000
32000
32000
27000
21000
6000
6000
6000
24000
24000
20000
12000
8000
22000
22000
22000
22000
20000
20000
1000
1000
600
500
300
250
4400
4400
4000
1900
1400
700
300
6000
6000
5000
3400
1400
900
400
8000
8000
6000
5000
5000
3500
1000
1000
800
600
7000
7000
5000
3800
2700
700
700
600
6000
3800
3000
1700
1000
6000
4400
3800
3600
6000
3000
39.4
39.4
23.6
19.7
11.8
9.8
173.2
173.2
157.5
74.8
55.1
27.6
11.8
236.2
236.2
196.9
133.9
55.1
35.4
15.7
315.0
315.0
236.2
196.9
196.9
137.8
39.4
39.4
31.5
23.6
275.6
275.6
196.9
149.6
106.3
27.6
27.6
23.6
236.2
149.6
118.1
66.9
39.4
236.2
173.2
149.6
141.7
236.2
118.1
0.01
0.01
0.008
0.008
0.005
0.005
0.06
0.04
0.04
0.02
0.02
0.008
0.006
0.07
0.07
0.06
0.04
0.03
0.02
0.01
0.1
0.1
0.1
0.08
0.08
0.05
0.04
0.04
0.02
0.02
0.15
0.15
0.1
0.1
0.08
0.08
0.06
0.04
0.2
0.15
0.1
0.1
0.05
0.2
0.2
0.15
0.1
0.2
0.15
20000
20000
18000
18000
13000
13000
40000
40000
40000
27000
16000
15000
11000
36000
36000
36000
29000
15000
12000
9000
32000
32000
32000
32000
32000
26000
10000
10000
10000
10000
26000
26000
26000
22000
17000
6000
6000
6000
19000
19000
16000
12000
8000
18000
18000
18000
18000
16000
16000
800
800
480
400
240
200
3500
3500
3200
1500
1100
560
240
4300
4300
3600
2400
1100
720
320
5000
5000
3800
3200
3200
2200
800
800
640
480
4500
4500
3200
2400
1700
560
560
480
3800
2400
1900
1400
800
3800
2800
2400
2300
3800
1900
31.5
31.5
18.9
15.7
9.4
7.9
137.8
137.8
126.0
59.1
43.3
22.0
9.4
169.3
169.3
141.7
94.5
43.3
28.3
12.6
196.9
196.9
149.6
126.0
126.0
86.6
31.5
31.5
25.2
18.9
177.2
177.2
126.0
94.5
66.9
22.0
22.0
18.9
149.6
94.5
74.8
55.1
31.5
149.6
110.2
94.5
90.6
149.6
74.8
0.01
0.01
0.008
0.008
0.005
0.005
0.06
0.04
0.04
0.02
0.02
0.008
0.006
0.07
0.07
0.06
0.04
0.03
0.02
0.01
0.1
0.1
0.1
0.08
0.08
0.05
0.04
0.04
0.02
0.02
0.15
0.15
0.1
0.1
0.08
0.08
0.06
0.04
0.2
0.15
0.1
0.1
0.05
0.2
0.2
0.15
0.1
0.2
0.15
SOLID END MILLS
Work material

Depth of cut
R:Radius
2) Cutting conditions may differ considerably due to the overhang, depth of cut, and machine tool conditions. Please use the above table
as a start reference point.
MS2XLB
I080
I211
CUTTING CONDITIONS
- Inch sizes
MS2XLB
y MS2XLB
- Inch sizes
MS4XLB
y MS4XLB
Work material
Work material
AISI H13 etc.
R
(inch)
.0078
.0156
.0313
.0469
.0625
.0938
.1250
AISI H13 etc.
Neck length
(inch)
Revolution
(min-1)
Table feed
(IPM)
Depth of cut
ap
(inch)
.0938
.1290
.1875
.1875
.2500
.3750
.3750
.5000
.7500
.5625
.7500
1.1250
.7500
1.1250
1.5000
40000
30000
20000
40000
25000
15000
40000
30000
10000
40000
20000
10000
30000
20000
15000
21.2
17.7
10.6
70.8
44.3
26.6
113.4
85.1
28.4
141.8
70.8
35.5
124.0
106.3
106.3
.0002
.0002
.0001
.0008
.0008
.0004
.0028
.0016
.0008
.003
.002
.001
.004
.006
.008
<0.1R
<0.2R
R
(inch)
.0313
.0156
.0625
.0938
.1250
Neck length
(inch)
Revolution
(min-1)
Table feed
(IPM)
Depth of cut
ap
(inch)
.3750
.5000
.7500
.5625
.7500
1.1250
.7500
1.1250
1.5000
40000
30000
10000
40000
20000
10000
30000
20000
15000
151.2
113.4
37.8
189.0
94.4
47.3
165.4
141.7
141.7
.0028
.0016
.0008
.003
.002
.001
.004
.006
.008
<0.1R
<0.2R
(R<3/64)
(R>3/64)
Depth of cut
<ap
R:Radius
(R<3/64)
(R>3/64)
Depth of cut
<ap
SOLID END MILLS
R:Radius
I212
MS2XLB
I085
MS4XLB
I086
MS2XB

Work material
Work material
Table feed
Taper angle Neck length Depth of cut Revolution
(mm)
one side
(mm)
(min-1) (mm/min)
(IPM)
30'
30'
R0.1
1
1
2
2
3
3
5
30'
R0.15
1
2
3
5
30'
30'
R0.2
1
1
1
2
30'
30'
R0.25
1
1
2
2
30'
30'
R0.3
1
1
1
2
2
30'
30'
R0.4
1
1
2
3
1.5
2
1.5
2
1.5
2
1.5
2
2
3
3
3
3
3
2
5
2
5
2
5
3
5
3
5
3
5
5
8
5
10
15
6
8
8
12
8
12
8
12
0.005
0.005
0.005
0.005
0.01
0.01
0.01
0.01
0.01
0.005
0.005
0.01
0.01
0.01
0.02
0.01
0.02
0.01
0.02
0.01
0.03
0.02
0.03
0.02
0.03
0.02
0.03
0.02
0.03
0.02
0.01
0.03
0.02
0.05
0.04
0.05
0.04
0.08
0.06
R
(mm)
Table feed
Taper angle Neck length Depth of cut Revolution
(mm)
one side
(mm)
(min-1) (mm/min)
(IPM)
30'
30'
30'
30000
300
11.8
R0.5
1
1
1
2
3
5
30'
30'
30000
30000
30000
300
300
300
11.8
11.8
R0.6
30'
30'
R0.75
400
11.8
500
1
1
1
2
3
5
15.7
30'
30'
R1.5
30000
1
1
2
30'
30'
30'
R1
30000
1
1
2
2
19.7
R2
1
1
2
3
30'
1
10
20
30
10
20
35
20
40
20
12
24
12
24
12
24
10
30
10
30
30
20
30
40
20
40
50
40
40
38.2
30
50
30
50
48.9
50
60
60
0.05
0.02
0.005
0.05
0.02
0.005
0.03
0.05
0.05
0.05
0.02
0.05
0.02
0.06
0.03
0.1
0.02
0.1
0.05
0.1
0.05
0.03
0.02
0.05
0.03
0.02
0.1
0.1
0.1
0.1
0.03
0.1
0.03
0.1
0.1
0.1
0.1
22000
530
20.9
22000
600
23.6
20000
700
27.6
18000
1000
39.4
16000
1300
51.2
14000
1100
43.3
SOLID END MILLS
R
(mm)

<0.1R(R<0.5)
<0.2R(R>0.5)
Depth of cut
ap
R:Radius
MS2XB
I087
I213
CUTTING CONDITIONS
MS2XLRB

Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.
AISI H13, AISI W1 -10,

AISI P21 etc.
AISI 304, AISI 306,

Ti -6Al -4V etc.
AISI H13 etc.
Table feed
Revolution
(min-1) (mm/min)
(IPM)
Table feed
Revolution
(min-1) (mm/min)
(IPM)
Table feed
Revolution
(min-1) (mm/min)
(IPM)
Table feed
Revolution
(min-1)
(IPM)
(mm/min)
Work material
Dia.
(mm)
1
2
3
4
6
1
2
3
4
6
Neck length
(mm)
2
4
6
8
12
5
10
15
20
30
(2D)
(5D)
30000
15000
10000
7500
5000
22000
11000
7400
5600
3700
600
600
600
600
600
350
350
350
350
350
23.6
23.6
23.6
23.6
23.6
13.8
13.8
13.8
13.8
13.8
20000
10000
7000
5200
3500
17000
8800
5800
4400
2900
400
400
400
400
400
280
280
280
280
280
15.7
15.7
15.7
15.7
15.7
11.0
11.0
11.0
11.0
11.0
18000
9100
6000
4500
3000
14000
7200
4800
3600
2400
300
300
300
300
300
200
200
200
200
200
(Neck length=2D)
(Neck length=2D)
(Neck length=5D)
(Neck length=5D)
11.8
11.8
11.8
11.8
11.8
7.9
7.9
7.9
7.9
7.9
15000
8000
5000
4000
2700
12000
6400
4200
3200
2100
120
120
120
120
120
100
100
100
100
100
4.7
4.7
4.7
4.7
4.7
3.9
3.9
3.9
3.9
3.9
SOLID END MILLS
Depth of cut
I214
D:Dia.
MS2XLRB
I092
MS4MRB
Work
material


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti -6Al -4V etc.
AISI H13 etc.
Table feed
Table feed
Table feed
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
3
4
5
6
8
10
12
16
20
16000
12000
9600
8000
6000
4800
4000
3000
2400
1500
1800
1800
1800
1600
1400
1200
960
800
59.1
70.9
70.9
70.9
63.0
55.1
47.2
37.8
31.5
10000
8000
6400
5300
4000
3200
2700
2000
1600
800
1000
1000
1000
900
800
700
560
480
31.5
39.4
39.4
39.4
35.4
31.5
27.6
22.0
18.9
7400
5600
4400
3700
2800
2200
1800
1400
1100
480
600
600
600
560
500
430
360
300
18.9
23.6
23.6
23.6
22.0
19.7
16.9
14.2
11.8
8000
6000
4800
4000
3000
2400
2000
1500
1200
240
240
240
240
240
240
230
190
170
9.4
9.4
9.4
9.4
9.4
9.4
9.1
7.5
6.7
Depth of
cut
MS4MRB
I093
SOLID END MILLS
D:Dia.
I215
CUTTING CONDITIONS
MSMHDRB
y Shoulder milling
Work
material
Dia.
(mm)
2
3
4
5
6
8
10
12
16
18
20


Pre-hardened steel

Titanium alloy
Heat resistant alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti -6Al -4V etc.
AISI H13 etc
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
15000
11000
8000
6400
5900
4400
3500
2900
2200
2000
1800
10000
7400
5600
4500
3700
2800
2300
1900
1400
1250
1100
10000
7400
5600
4500
3700
2800
2300
1900
1400
1250
1100
550
800
900
1000
1100
1100
1000
1000
800
800
750
21.7
31.5
35.4
39.4
43.3
43.3
39.4
39.4
31.5
31.5
29.5
340
500
540
600
640
660
640
640
500
480
460
13.4
19.7
21.3
23.6
25.2
26.0
25.2
25.2
19.7
18.9
18.1
320
480
520
580
600
600
560
530
450
450
440
12.6
18.9
20.5
22.8
23.6
23.6
22.0
20.9
17.7
17.7
17.3
6400
4800
3600
2900
2400
1800
1400
1200
900
800
720
160
250
270
300
320
330
320
320
250
240
230
6.3
9.8
10.6
11.8
12.6
13.0
12.6
12.6
9.8
9.4
9.1
4800
4000
3200
2600
2100
1600
1300
1100
800
640
510
100
170
240
240
230
220
200
170
130
100
80
3.9
6.7
9.4
9.4
9.1
8.7
7.9
6.7
5.1
3.9
3.1
Depth of
cut
D:Dia.
y Slotting
SOLID END MILLS
Work
material
Dia.
(mm)
2
3
4
5
6
8
10
12
16
18
20


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti -6Al -4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
12000
9000
7200
5800
5000
3700
3000
2500
2000
1800
1600
400
600
720
720
800
800
720
600
480
460
430
15.7
23.6
28.3
28.3
31.5
31.5
28.3
23.6
18.9
18.1
16.9
7000
5300
4000
3200
2700
2000
1600
1300
1000
900
800
200
300
360
360
400
400
360
290
230
210
200
7.9
11.8
14.2
14.2
15.7
15.7
14.2
11.4
9.1
8.3
7.9
7000
5300
4000
3200
2700
2000
1600
1300
1000
900
800
100
150
180
180
200
200
180
150
120
110
100
3.9
5.9
7.1
7.1
7.9
7.9
7.1
5.9
4.7
4.3
3.9
4200
3200
2400
1900
1600
1200
960
800
600
550
480
80
130
140
150
160
170
160
140
110
110
100
3.1
5.1
5.5
5.9
6.3
6.7
6.3
5.5
4.3
4.3
3.9
2300
1900
1400
1100
950
720
570
480
360
290
230
40
70
95
95
95
90
80
70
50
40
35
1.6
2.8
3.7
3.7
3.7
3.5
3.1
2.8
2.0
1.6
1.4
Depth of
cut
D:Dia.
I216
MSMHDRB
I095
MS2MT
y Slotting
Work
material


Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI H13 etc.
Small
Mill Dia.
(mm)
Revolution
(min-1)
(mm/min)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
40000
40000
40000
37000
32000
27000
24000
21000
19000
13000
320
400
450
500
530
560
610
610
610
720
Table feed
(IPM)
Depth of cut Revolution

(mm)
(min-1)
12.6
15.7
17.7
19.7
20.9
22.0
24.0
24.0
24.0
28.3
0.005
0.006
0.008
0.010
0.013
0.015
0.018
0.020
0.025
0.040
40000
40000
40000
32000
26000
23000
20000
18000
16000
11000
Table feed
(IPM)
(mm/min)
180
220
270
320
340
380
410
450
450
540

(mm)
(min-1)
7.1
8.7
10.6
12.6
13.4
15.0
16.1
17.7
17.7
21.3
Depth of
cut
0.004
0.005
0.006
0.008
0.010
0.011
0.013
0.015
0.020
0.030
40000
35000
31000
25000
21000
18000
16000
14000
13000
8500
Table feed
(IPM)
(mm/min)
100
130
150
160
170
180
210
210
210
270
Depth of cut
(mm)
3.9
5.1
5.9
6.3
6.7
7.1
8.3
8.3
8.3
10.6
0.002
0.003
0.004
0.005
0.006
0.007
0.008
0.009
0.010
0.015
Please refer to the list.
Work
material


Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI H13 etc.
Small
Mill Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
2
2.5
3
4
5
6
8
10
9500
7800
6400
4800
3800
3200
2400
1900
720
800
800
800
800
800
700
600
28.3
31.5
31.5
31.5
31.5
31.5
27.6
23.6
8000
6300
5300
4000
3200
2600
2000
1600
540
540
540
540
540
540
480
410
21.3
21.3
21.3
21.3
21.3
21.3
18.9
16.1
6400
5000
4200
3200
2500
2100
1600
1300
300
300
300
300
300
300
270
240
11.8
11.8
11.8
11.8
11.8
11.8
10.6
9.4
Table feed
Table feed
Table feed
SOLID END MILLS
y Shoulder milling
Depth of
cut
D:End point diameter
MS2MT
I097
I217
CUTTING CONDITIONS
MS4LT

AISI H13 etc.
Work material
Small mill dia.

(mm)
R
(mm)
0.2
0.3

2
3
0.4
0.5
0.6
R 0.3
0.7
Length of cut
(mm)
4
6
4
6
6
8
Table feed
Revolution
(min-1)
(mm/min)
20000 40000
20000 40000
20000 40000
200 500
200 500
200 500
(IPM)
7.9 19.7
7.9 19.7
7.9 19.7
20000 38000
200 500
7.9 19.7
18000 32000
250 600
9.9 23.6
16000 27000
250 600
9.9 23.6
14000 24000
250 600
9.9 23.6
R 0.4
8
12
R 0.5
10
300 800
11.8 31.5
10
1.3
12
1.4
12
SOLID END MILLS
R 0.75
2.5
3.0
13000 24000
200 400
7.9 15.8
11000 20000
200 400
7.9 15.8
10000 18000
200 400
7.9 15.8
0.01
0.007
0.015
0.01
0.02
0.02
300 800
300 800
11.8 31.5
11.8 31.5
0.03
0.035
0.001
0.001
0.002
0.005
0.003
0.005
0.004
0.008
0.005
0.015
0.01
0.007
0.015
8000 14000
200 500
7.9 19.7
0.01
0.008
0.02
6600 12000
200 500
7.9 19.7
6100 11000
5700 10000
200 500
200 500
7.9 19.7
7.9 19.7
0.02
0.015
0.01
0.015
0.018
0.06
0.03
10
0.04
0.02
16
7500 13000
300 800
11.8 31.5
12
16
16
12
20
0.03
200 500
7.9 19.7
7000 12000
300 800
11.8 31.5
0.06
0.03
0.025
0.035
5000 9000
200 500
7.9 19.7
0.025
300 800
11.8 31.5
0.05
0.04
4400 8000
200 500
7.9 19.7
0.03
5500 9500
300 800
11.8 31.5
0.05
0.04
0.04
0.1
11.8 31.5
0.06
30
0.03
25
40
0.08
0.04
3700 6400
300 800
11.8 31.5
0.015
0.1
10
300 800
0.03
0.07
0.02
4400 7600
0.02
0.015
0.08
6200 11000
0.015
0.008
0.045
30
20
5300 9500
0.015
8
R1
7.9 15.8
0.005
8500 15000
8000 14000
24
2.0
200 400
0.01
0.04
8
R 0.9
16000 29000
0.003
0.03
20
1.8
5.9 11.8
5.9 11.8
5.9 11.8
11.8 31.5
8
150 300
150 300
150 300
300 800
25
1.6
20000 40000
20000 40000
20000 36000
9200 16000
16
1.5
0.001
0.002
Depth of cut
(mm)
0.015
6
R 0.6
(IPM)
0.03
1100019000
16
1.2
(mm/min)
0.013
6
1.0
Revolution
(min-1)
0.03
4
0.8
Table feed
Depth of cut
(mm)
4000 7200
200 500
7.9 19.7
0.02
0.01
0.05
3200 5700
200 500
7.9 19.7
0.03
0.015
2700 4800
200 500
7.9 19.7
0.04
0.02
I218
MS4LT
I101
MS4LTB

AISI H13 etc.
Work material
R0.3
R0.4
R0.5
R0.6
R0.75
R0.9
R1
Length of cut
(mm)
4
6
6
8
10
8
10
12
16
8
10
12
16
8
10
12
16
20
8
10
12
16
20
10
12
16
20
25
30
Revolution
(min-1)
Table feed
(IPM)
(mm/min)
18000 32000 250 600 9.8 23.6
14000 24000 250 600 9.8 23.6
11000 19000 300 800 11.8 31.5
9200 16000 300 800 11.8 31.5
7500 13000 300 800 11.8 31.5
6200 11000 300 800 11.8 31.5
5500 9500
300 800 11.8 31.5
Depth of cut
(mm)
0.01
0.007
0.025
0.02
0.015
0.025
0.02
0.018
0.015
0.035
0.03
0.027
0.02
0.05
0.04
0.035
0.03
0.02
0.08
0.07
0.06
0.05
0.04
0.08
0.07
0.05
0.04
0.03
0.02
Revolution
(min-1)
Table feed
(IPM)
Depth of cut
(mm)
(mm/min)
13000 24000 200 400 7.9 15.7
10000 18000 200 400 7.9 15.7
8000 14000 200 500 7.9 19.7
6600 12000 200 500 7.9 19.7
5300 9500
200 500 7.9 19.7
4400 8000
200 500 7.9 19.7
4000 7200
200 500 7.9 19.7
0.005
0.004
0.013
0.01
0.008
0.013
0.01
0.009
0.008
0.018
0.015
0.013
0.01
0.025
0.02
0.018
0.015
0.01
0.04
0.035
0.035
0.03
0.02
0.045
0.04
0.03
0.02
0.015
0.01
SOLID END MILLS
R
(mm)
MS4LTB
I108
I219
CUTTING CONDITIONS
VCMDSC
End mill, Medium cut length, 4 6 ute
Work
material
Dia.
(mm)
0.5
1
1.5
2
3
AISI H13 etc.
AISI D2 etc.
Table feed
Table feed
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ae, ap (mm)
Revolution
(min-1)
(mm/min)
40000
40000
40000
40000
34000
2000
3000
5000
5600
5600
78.7
118.1
196.9
220.5
220.5
0.03
0.05
0.08
0.10
0.15
30000
20000
18000
16000
13000
600
900
1100
1300
1600
(IPM)
Depth of cut
ae, ap (mm)
23.6
35.4
43.3
51.2
63.0
0.02
0.03
0.05
0.06
0.09
Depth of
cut
D:Dia.
SOLID END MILLS
2) The above condition are for shoulder milling. In slotting with over &3, please set the revolution, feed rate and depth of cut at 20 40% of
above value.
I220
VCMDSC
I112
VCLD
Work
material

Pre-hardened steel

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
AISI W1, AISI M2 etc.
Table feed
Table feed
Table feed
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
6
8
10
12
16
20
25
2100
1600
1300
1100
800
640
510
450
430
420
380
310
270
230
17.7
16.9
16.5
15.0
12.2
10.6
9.1
1600
1200
960
800
600
480
380
330
310
290
260
220
190
160
13.0
12.2
11.4
10.2
8.7
7.5
6.3
1300
1000
800
660
500
400
320
240
230
220
200
160
140
120
9.4
9.1
8.7
7.9
6.3
5.5
4.7
1100
800
640
530
400
320
260
190
170
150
140
120
110
90
7.5
6.7
5.9
5.5
4.7
4.3
3.5
Depth of
cut
D:Dia.
SOLID END MILLS
VCLD
I113
I221
CUTTING CONDITIONS
VCMH
End mill, Medium cut length, 3 4 ute, High helix angle
Work
material


Titanium alloy

AISI 304, AISI 306,

Ti -6Al -4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
3
4
5
6
8
10
12
16
18
20
25
5300
4400
3600
3200
2400
1900
1600
1200
1100
960
760
130
220
260
280
300
290
250
180
170
190
150
5.1
8.7
10.2
11.0
11.8
11.4
9.8
7.1
6.7
7.5
5.9
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
4400
3700
3000
2700
2000
1600
1300
1000
900
800
640
100
160
190
200
210
210
170
130
120
140
110
3.9
6.3
7.5
7.9
8.3
8.3
6.7
5.1
4.7
5.5
4.3
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
2400
2000
1700
1500
1200
960
800
600
530
480
380
50
80
100
100
110
115
95
70
65
75
60
2.0
3.1
3.9
3.9
4.3
4.5
3.7
2.8
2.6
3.0
2.4
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
1500
1300
1100
1000
800
640
530
400
350
320
260
25
40
50
50
45
45
40
30
25
25
20
1.0
1.6
2.0
2.0
1.8
1.8
1.6
1.2
1.0
1.0
0.8
Depth of
cut
SOLID END MILLS
D:Dia.
I222
2) The above table shows cutting conditions for shoulder milling. For slotting, please set the revolution at 80 100% and the feed rate at
60 80% of the table gure. Please set the revolution rate at 60% and the feed rate at 40% when slotting austenitic stainless steels.
VCMH
I114
VC6MH
VC8MH
Work
material


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti -6Al -4V etc.
Inconel718 etc.
Table feed
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
6
8
10
12
16
20
25
10600
8000
6400
5300
4000
3200
2500
2900
2900
2700
2700
2200
1900
1600
114.2
114.2
106.3
106.3
86.6
74.8
63.0
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
8000
6000
4800
4000
3000
2400
1900
2000
2000
2000
2000
1600
1400
1200
78.7
78.7
78.7
78.7
63.0
55.1
47.2
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
4200
3200
2500
2100
1600
1300
1000
900
900
870
830
740
710
560
35.4
35.4
34.3
32.7
29.1
28.0
22.0
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
2100
1600
1300
1100
800
640
510
320
300
260
230
180
150
120
12.6
11.8
10.2
9.1
7.1
5.9
4.7
Depth of
cut
D:Dia.
SOLID END MILLS
VC6MH
I115
VC8MH
I116
I223
CUTTING CONDITIONS
VCSFPR
y Shoulder milling
Work
material
Dia.
(mm)
3
4
5
6
8
10
12
16
20


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti -6Al -4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
16000
12000
9500
8000
6000
4800
4000
3000
2400
960
960
960
960
1050
1050
960
840
760
37.8
37.8
37.8
37.8
41.3
41.3
37.8
33.1
29.9
13000
9500
7600
6400
4800
3800
3200
2400
1900
640
640
640
680
760
760
700
620
560
25.2
25.2
25.2
26.8
29.9
29.9
27.6
24.4
22.0
6400
4800
3800
3200
2400
1900
1600
1200
1000
260
260
260
290
340
340
320
300
300
10.2
10.2
10.2
11.4
13.4
13.4
12.6
11.8
11.8
5300
4000
3200
2700
2000
1600
1300
1000
800
100
100
100
110
140
150
150
150
140
3.9
3.9
3.9
4.3
5.5
5.9
5.9
5.9
5.5
4200
3200
2500
2100
1600
1300
1100
800
600
70
70
70
75
95
105
110
110
100
2.8
2.8
2.8
3.0
3.7
4.1
4.3
4.3
3.9
Depth of
cut
D:Dia.
y Slotting
SOLID END MILLS
Work
material
Dia.
(mm)
3
4
5
6
8
10
12
16
20


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti -6Al -4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
13000
9500
7600
6400
4800
3800
3200
2400
1900
720
720
720
720
800
800
750
620
540
28.3
28.3
28.3
28.3
31.5
31.5
29.5
24.4
21.3
11000
8000
6400
5300
4000
3200
2700
2000
1600
480
480
480
480
520
520
520
450
400
18.9
18.9
18.9
18.9
20.5
20.5
20.5
17.7
15.7
4800
3600
3200
2700
2000
1600
1300
1000
800
190
190
190
200
220
220
210
180
160
7.5
7.5
7.5
7.9
8.7
8.7
8.3
7.1
6.3
3200
2400
1900
1600
1200
1000
800
600
500
50
50
50
55
70
70
75
75
70
2.0
2.0
2.0
2.2
2.8
2.8
3.0
3.0
2.8
2100
1600
1300
1100
800
600
500
400
300
25
25
25
30
35
35
40
45
40
1.0
1.0
1.0
1.2
1.4
1.4
1.6
1.8
1.6
Depth of
cut
D:Dia.
I224
VCSFPR
I117
VC2ESB
Work
material
R
(mm)
R
R
R
R
R
R
R
R
R
R
0.5
0.75
1
1.5
2
2.5
3
4
5
6

Pre-hardened steel

AISI P21 etc.
AISI H13 etc.

% >15
% < 15
Table feed
Revolution
(min-1) (mm/min)
40000
40000
40000
40000
32000
25000
21000
16000
13000
9000
5600
6500
6500
7500
7500
6000
5800
4500
3600
2500
(IPM)
220.5
256.0
256.0
295.3
295.3
236.2
228.3
177.2
141.7
98.5
Table feed
Revolution
(min-1) (mm/min)
40000
40000
39000
27000
20000
16000
13000
10000
8000
6000
3200
3200
3800
4300
3600
2900
2600
2000
1700
1300
(IPM)
126.0
126.0
149.6
169.3
141.7
114.2
102.4
78.7
66.9
51.2
% < 15
Depth of
cut ap Revolution
Table feed
(mm)
0.06
0.09
0.11
0.13
0.15
0.20
0.25
0.30
0.50
0.50
40000
40000
40000
32000
25000
20000
17000
13000
10000
7200
5600
6500
6500
6000
6000
5400
4700
3600
2900
2000
220.5
256.0
256.0
236.2
236.2
212.6
185.0
141.7
114.2
78.7
% >15
Table feed
Revolution
40000
32000
31000
22000
16000
13000
10000
8000
6400
4800
3000
3200
3500
3400
2700
2300
2000
1500
1200
1000
118.1
126.0
137.8
133.9
106.3
90.6
78.7
59.1
47.2
39.4
Depth of
cut ap
(mm)
0.06
0.09
0.11
0.13
0.15
0.20
0.25
0.30
0.50
0.50
< 0.2R
Depth of
cut
< ap
R:Radius
SOLID END MILLS

VC2ESB
I118
I225
CUTTING CONDITIONS
VC2PSBP
Ball nose, Short cut length, Ultra high precision
Work
material
R
(mm)
R0.05
R0.1
R0.15
R0.2
R0.25
R0.3
R0.35
R0.4
R0.45
R0.5
R0.75
R1
R1.5
R2
R2.5
R3
R4
R5
R6
VC2PSB

Pre-hardened steel

AISI P21 etc.
AISI H13 etc.
% >15
% < 15
Table feed
% < 15
Table feed
% >15
Table feed
Table feed
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
35000
30000
25000
23000
20000
15000
12000
10000
200
600
900
1000
1500
2000
2800
2800
3200
3200
3600
3500
3400
3400
3400
3400
3000
3000
2600
7.9
23.6
35.4
39.4
59.1
78.7
110.2
110.2
126.0
126.0
141.7
137.8
133.9
133.9
133.9
133.9
118.1
118.1
102.4

40000
40000
40000
40000
40000
40000
40000
38000
35000
30000
25000
23000
20000
17000
15000
12500
10000
8300

400
600
700
1000
1500
2100
2100
2200
2200
2300
2200
2200
2200
2200
2200
2000
2000
1800

15.7
23.6
27.6
39.4
59.1
82.7
82.7
86.6
86.6
90.6
86.6
86.6
86.6
86.6
86.6
78.7
78.7
70.9
40000
40000
40000
40000
40000
40000
40000
40000
38000
35000
32000
28000
24000
20000
18000
16000
10000
8000
6600
170
600
900
1000
1500
2000
2800
2800
3000
3000
3000
2800
2600
2600
2600
2600
2000
2000
1700
6.7
23.6
35.4
39.4
59.1
78.7
110.2
110.2
118.1
118.1
118.1
110.2
102.4
102.4
102.4
102.4
78.7
78.7
66.9

40000
40000
40000
40000
40000
37000
35000
32000
30000
25000
20000
16000
14000
12000
10000
7500
6000
5000

400
600
700
1000
1500
1800
1800
1800
1800
1800
1700
1500
1500
1500
1400
1200
1200
1100

15.7
23.6
27.6
39.4
59.1
70.9
70.9
70.9
70.9
70.9
66.9
59.1
59.1
59.1
55.1
47.2
47.2
43.3
SOLID END MILLS
< 0.1R
I226
Depth of
cut
< 0.06R
R:Radius

VC2PSBP
I120
VC2PSB
I119
VCXB
Pre-hardened steel

AISI P21 etc.
AISI H13 etc.
Work material
R0.5
R1
R2
R3
R4
R5
R6
Taper angle
one side
1
1
1
1
3
5
1
1
1
1
3
5
1
1
1
1
3
1
1
1
1
3
1
3
1
1
1
3
1
1
1
3
30'
30'
30'
30'
30'
30'
30'
Neck length
(mm)
16
21
26
23
42
23
21
31
41
23
41
23
36
46
60
49
28
51
65
92
53
34
55
36
70
100
59
40
70
100
83
63
Depth of cut
ap
(mm)
0.02
0.01
0.01
0.02
0.05
0.05
0.05
0.04
0.03
0.1
0.1
0.1
0.2
0.15
0.1
0.2
0.2
0.3
0.2
0.1
0.3
0.3
0.4
0.4
0.4
0.3
0.5
0.5
0.6
0.4
0.6
0.6
Table feed
Revolution
(min-1)
(mm/min)
0.1
22000
0.2
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
530
20.9
12000
230
9.1
18000
570
22.4
10000
260
10.2
0.8
14000
670
26.4
6000
200
7.9
1.2
10000
840
33.1
5000
220
8.7
1.6
8000
840
33.1
4000
270
10.6
6000
840
33.1
3000
310
12.2
2.4
5000
900
35.4
2500
340
13.4
ae
(mm)
(IPM)
SOLID END MILLS
R
(mm)
ae
Depth of cut
ap
VCXB
I121
I227
CUTTING CONDITIONS
VC3MB
yRoughing

Work Alloy steel, Pre-hardened steel
material
AISI 1050, AISI No 35 B, AISI P20, AISI P21 etc.
R
(mm)
R1
R2
R3
R4
R5
R6
R8
R10
Revolution
(min-1)
32000
18500
13000
10000
8000
6600
5000
4000
% < 15
Table feed
(mm/min)
(IPM)
3000
3700
4000
5000
5000
4600
4000
3600
118.1
145.7
157.5
196.9
196.9
181.1
157.5
141.7
Revolution
(min-1)
25000
14500
10000
8000
6500
5300
4000
3200
AISI H13 etc.

% >15
Table feed
(mm/min)
(IPM)
1170
1460
1500
2000
2000
1800
1600
1440
Revolution
(min-1)
46.1
57.5
59.1
78.7
78.7
70.9
63.0
56.7
% < 15
Table feed
(mm/min)
(IPM)
18000
11000
7700
6000
4800
4000
3000
2400
1440
1760
1920
2300
2200
2100
1700
1400
56.7
69.3
75.6
90.6
86.6
82.7
66.9
55.1
Revolution
(min-1)
16000
9200
6400
4800
3800
3200
2400
1900
% >15
Table feed
(mm/min)
(IPM)
640
740
800
920
870
840
680
550
25.2
29.1
31.5
36.2
34.3
33.1
26.8
21.7
< 0.5R
Depth of
cut
< 0.2R
R:Radius
yFinishing

Work Alloy steel, Pre-hardened steel
material
AISI 1050, AISI No 35 B, AISI P20, AISI P21 etc.
SOLID END MILLS
R
(mm)
R1
R2
R3
R4
R5
R6
R8
R10
Revolution
(min-1)
32000
25500
20000
15000
12000
10000
7500
6000
% < 15
Table feed
(IPM)
(mm/min)
3200
5000
6100
7500
7500
7000
6000
5400
126.0
196.9
240.2
295.3
295.3
275.6
236.2
212.6
Revolution
(min-1)
32000
20000
15000
11000
9000
7500
5600
4500
AISI H13 etc.

% >15
Table feed
(mm/min)
(IPM)
1500
2000
2200
2700
2700
2500
2200
2000
Revolution
(min-1)
59.1
78.7
86.6
106.3
106.3
98.4
86.6
78.7
25000
17000
13000
10000
8000
6600
5000
4000
% < 15
Table feed
(IPM)
(mm/min)
2000
2700
3200
3800
3700
3500
2800
2300
78.7
106.3
126.0
149.6
145.7
137.8
110.2
90.6
Revolution
(min-1)
20000
13000
10000
7500
6000
5000
3700
3000
% >15
Table feed
(IPM)
(mm/min)
800
1000
1200
1400
1400
1300
1000
900
31.5
39.4
47.2
55.1
55.1
51.2
39.4
35.4
< 0.1R
Depth of
cut
< 0.06R
R:Radius

I228
VC3MB
I123
VC4MB
Work
material
R
(mm)
R
R
R
R
R
R
R
R
R
R
R
R
0.5
0.75
1
1.5
2
2.5
3
4
5
6
8
10

Pre-hardened steel,
Hardened steel ( 55HRC)
AISI H13, AISI W1 -10, AISI P21 etc.
AISI D2 etc.
% >15
% < 15
Table feed
Revolution
40000
40000
40000
40000
32000
25000
21000
16000
13000
9000
7500
6000
8000
9600
9600
12000
11000
9000
8400
6400
5200
3600
2400
2000
315.0
378.0
378.0
472.4
433.1
354.3
330.7
252.0
204.7
141.7
94.5
78.7
Table feed
Revolution
40000
40000
40000
32000
24000
19000
15000
12000
9600
7200
5000
4000
3800
4800
5600
5600
4700
3800
3400
2600
2200
1700
1500
1300
149.6
189.0
220.5
220.5
185.0
149.6
133.9
102.4
86.6
66.9
59.1
51.2
% < 15
Depth of
cut ap Revolution
Table feed
(mm)
0.06
0.09
0.11
0.13
0.15
0.20
0.25
0.30
0.50
0.50
0.50
0.50
40000
40000
40000
32000
24000
19000
16000
12000
10000
7000
5000
4000
5600
7200
8000
7700
6200
5300
4800
3600
3200
2200
1100
900
220.5
283.5
315.0
303.1
244.1
208.7
189.0
141.7
126.0
86.6
43.3
35.4
% >15
Table feed
Revolution
40000
38000
28000
19000
14000
12000
9600
7200
5800
4300
3100
2500
3100
4200
3100
2900
2500
2200
2000
1600
1300
940
600
500
122.0
165.4
122.0
114.2
98.4
86.6
78.7
63.0
51.2
37.0
23.6
19.7
Depth of
cut ap
(mm)
0.05
0.08
0.10
0.12
0.13
0.15
0.20
0.20
0.20
0.30
0.30
0.30
< 0.2R
Depth of
cut
< ap
R:Radius
SOLID END MILLS
VC4MB
I124
I229
CUTTING CONDITIONS
VCPSRB
Pre-hardened steel

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
Work material
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
2
4
4
6
8
4
6
10
6
10
15
4
6
10
6
10
15
8
15
10
15
20
12
20
30
15
30
18
41
50
24
50
30
50
36
48000
48000
48000
38000
29000
48000
38000
29000
48000
38000
29000
41000
32000
24000
36000
29000
22000
33000
20000
30000
24000
18000
26000
20000
15000
20000
12000
20000
15000
10000
15000
10000
12000
10000
10000
200 600
160 500
240 750
190 600
150 450
270 900
220 720
160 540
300 900
240 720
180 540
300 900
240 720
180 540
600 2000
480 1600
360 1200
750 2400
450 1400
900 3000
720 2400
540 1800
1200 4500
960 2000
720 1000
1200 4800
720 1900
1600 7500
900 2400
600 1200
1900 7500
1300 2400
1600 7500
1300 3200
1500 7500
7.9 23.6
6.3 19.7
9.4 29.5
7.5 23.6
5.9 17.7
10.6 35.4
8.7 28.3
6.3 21.3
11.8 35.4
9.4 28.3
7.1 21.3
11.8 35.4
9.4 28.3
7.1 21.3
23.6 78.7
18.9 63.0
14.2 47.2
29.5 94.5
17.7 55.1
35.4 118.1
28.3 94.5
21.3 70.9
47.2 177.2
37.8 78.7
28.3 39.4
47.2 189.0
28.3 74.8
63.0 295.3
35.4 94.5
23.6 47.2
74.8 295.3
51.2 94.5
63.0 295.3
51.2 126.0
59.1 295.3
40000
40000
32000
26000
19000
32000
26000
19000
32000
26000
19000
27000
22000
16000
24000
19000
14000
22000
13000
20000
16000
12000
17000
14000
10000
13000
8000
13000
12000
8000
10000
8000
8000
7000
7000
0.6
0.8
1.2
1.5
2.5
SOLID END MILLS
Table feed
Neck length
(mm)
8
10
12
< 0.2R
Depth of cut
< 0.4R
(D < & 2)
(D > & 2)
Table feed
(mm/min)
(IPM)
160 500
6.3 19.7
100 300
3.9 11.8
160 500
6.3 19.7
130 400
5.1 15.7
100 300
3.9 11.8
180 600
7.1 23.6
150 480
5.9 18.9
110 360
4.3 14.2
200 600
7.9 23.6
160 480
6.3 18.9
120 360
4.7 14.2
200 600
7.9 23.6
160 480
6.3 18.9
120 360
4.7 14.2
400 1300 15.7 51.2
320 1000 12.6 39.4
240 780
9.4 30.7
500 1600 19.7 63.0
300 960
11.8 37.8
600 2000 23.6 78.7
480 1600 18.9 63.0
360 1200 14.2 47.2
800 3000 31.5 118.1
640 2000 25.2 78.7
480 1000 18.9 39.4
780 3120 30.7 122.8
480 1600 18.9 63.0
1100 5000 43.3 196.9
720 1600 28.3 63.0
480 800
18.9 31.5
1300 5000 51.2 196.9
1000 2200 39.4 86.6
1100 5000 43.3 196.9
950 2200 37.4 86.6
1000 5000 39.4 196.9
< 0.1R
(D < & 1.5)

< 0.2mm (D < & 4)
< 0.5mm (D > & 6)
< 0.1mm
< 0.2R
Table feed
Revolution
(min-1)
(mm/min)
(IPM)
22000
22000
19000
16000
12000
19000
16000
12000
19000
15000
12000
16000
13000
10000
14000
12000
9000
13000
8000
12000
10000
7000
10000
8000
6000
10000
7000
8000
10000
6000
6000
3000
5000
2500
4000
80 250
50 150
80 250
70 200
50 150
90 300
70 240
60 180
100 300
80 240
60 180
100 300
80 240
60 180
200 650
160 520
120 390
250 800
150 480
300 1000
240 800
180 600
400 1500
320 2000
240 1000
520 2000
360 1120
550 2500
600 1200
360 530
650 2500
320 600
550 2500
280 600
500 2500
3.1 9.8
2.0 5.9
3.1 9.8
2.8 7.9
2.0 5.9
3.5 11.8
2.8 9.4
2.4 7.1
3.9 11.8
3.1 9.4
2.4 7.1
3.9 11.8
3.1 9.4
2.4 7.1
7.9 25.6
6.3 20.5
4.7 15.4
9.8 31.5
5.9 18.9
11.8 39.4
9.4 31.5
7.1 23.6
15.7 59.1
12.6 78.7
9.4 39.4
20.5 78.7
14.2 44.1
21.7 98.4
23.6 47.2
14.2 20.9
25.6 98.4
12.6 23.6
21.7 98.4
11.0 23.6
19.7 98.4
(D < & 2)
( D > & 2)
(D < & 1.5)

(D < & 4)
< 0.3mm (D > & 6)
< 0.05mm
< 0.1mm
D:Dia.
1) The cutting conditions above are a guide only to machining with cutting edges with a corner radius. When machining with peripheral cutting
edges, use the minimum feed rate as a guide.
3) When contour milling, cutting conditions can vary greatly due to the geometry of the workpiece and depth of cut.
I230
VCPSRB
I125
VCPSRB
yTaper neck type
Pre-hardened steel

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
Work material
Dia.
(mm)
1.5
1.5
2
2
2.5
2.5
3
3
4
4
5
5
6
8
10
Taper angle
one side
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
30'
30'
30'
30'
30'
30'
30'
30'
30'
30'
Table feed
Neck length
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
6
10
10
15
12
20
15
20
20
30
40
60
40
53
55
36000
28000
32000
25000
26000
20000
27000
21000
23000
18000
10000
7000
20000
15000
12000
270 810
210 630
540 1800
420 1400
600 1900
450 140
810 2700
630 2100
1080 3000
840 1500
520 1400
360 840
1650 4500
1950 4500
1650 4500
10.6 31.9
8.3 24.8
21.3 70.9
16.5 55.1
23.6 74.8
17.7 5.5
31.9 106.3
24.8 82.7
42.5 118.1
33.1 59.1
20.5 55.1
14.2 33.1
65.0 177.2
76.8 177.2
65.0 177.2
< 0.2R
Depth of cut
< 0.4R
(D < & 2)
(D > & 2)
Revolution
(min-1)
Table feed
(mm/min)
24000 180 540

19000 140 420
22000 360 1200
17000 280 910
18000 400 1300
13000 300 960
18000 540 1800
14000 420 1400
15000 720 3000
12000 560 1500
7000 420 840
5000 300 500
13000 1100 3000
10000 1300 3000
8000 1100 3000
Revolution
(min-1)
(mm/min)
(IPM)
7.1 21.3
5.5 16.5
14.2 47.2
11.0 35.8
15.7 51.2
11.8 37.8
21.3 70.9
16.5 55.1
28.3 118.1
22.0 59.1
16.5 33.1
11.8 19.7
43.3 118.1
51.2 118.1
43.3 118.1
15000
11000
13000
10000
11000
8000
11000
8000
9000
7000
5000
4000
8000
6000
5000
90 270
70 210
180 590
140 460
200 640
150 480
270 900
210 700
360 3000
280 1500
260 600
210 400
550 1500
650 1500
550 1500
3.5 10.6
2.8 8.3
7.1 23.2
5.5 18.1
7.9 25.2
5.9 18.9
10.6 35.4
8.3 27.6
14.2 118.1
11.0 59.1
10.2 23.6
8.3 15.7
21.7 59.1
25.6 59.1
21.7 59.1
< 0.1R
(D < & 1.5)

< 0.2mm (D < & 4)
< 0.5mm (D > & 6)
< 0.1mm
Table feed
(IPM)
< 0.2R
(D < & 2)
(D > & 2)
(D < & 1.5)

(D < & 4)
< 0.3mm (D > & 6)
< 0.05mm
< 0.1mm
VCPSRB
I128
SOLID END MILLS
D:Dia.
1) The cutting conditions above are a guide only to machining with cutting edges with a corner radius. When machining with peripheral cutting
edges, use the minimum feed rate as a guide.
I231
CUTTING CONDITIONS
VC4JRB
Corner radius end mill, Semi long cut length, 4 ute
Work
material


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti -6Al -4V etc.
AISI H13 etc.
Dia.
(mm)
Revolution
(min-1)
3
4
5
6
8
10
12
16
20
4200
3400
2900
2500
1900
1600
1300
1000
800
Table feed
(mm/min)
(IPM)
110
140
170
200
220
220
170
140
110
4.3
5.5
6.7
7.9
8.7
8.7
6.7
5.5
4.3
Revolution
(min-1)
3400
2700
2300
2000
1500
1300
1100
820
650
Table feed
(mm/min)
(IPM)
95
110
140
170
170
170
150
110
85
3.7
4.3
5.5
6.7
6.7
6.7
5.9
4.3
3.3
Revolution
(min-1)
2600
2100
1800
1500
1200
950
800
600
480
Table feed
(mm/min)
(IPM)
70
85
100
130
150
130
100
80
70
2.8
3.3
3.9
5.1
5.9
5.1
3.9
3.1
2.8
Revolution
(min-1)
2100
1700
1500
1300
1000
800
670
500
400
Table feed
(mm/min)
(IPM)
50
60
70
85
85
85
70
50
40
2.0
2.4
2.8
3.3
3.3
3.3
2.8
2.0
1.6
Depth of
cut
SOLID END MILLS
D:Dia.
I232
3) The above table shows cutting conditions for shoulder milling. For slotting, please reduce the feed rate only to 50% of the table gure.
Please set the revolution rate at 60% and the feed rate at 40% when slotting austenitic stainless steels.
VC4JRB
I129
VCHFRB
Carbon steel, Cast iron, Alloy steel ( 30HRC)
Alloy steel, Tool steel, Pre-hardened steel
AISI 1050, AISI 35, AISI P20 etc.
Work material
Dia.
(mm)
2
3
4
5
6
7
8
9
10
11
12
13
16
R
(mm)
R
R
R
R
R
R
R
R
R
R
R
R
R
0.5
0.75
1
1.2
1.5
1.5
2
2
2
2
3
3
3
Revolution
(min-1)
33000
22000
17000
13000
11000
9400
8200
7300
6500
6000
5500
5000
4100
Table feed
(mm/min)
(IPM)
10000
11000
12000
13000
13000
13000
13000
13000
13000
12000
12000
12000
10000
Revolution
(min-1)
Depth of cut Depth of cut

ae (mm)
ap (mm)
393.7
433.1
472.4
511.8
511.8
511.8
511.8
511.8
511.8
472.4
472.4
472.4
393.7
0.08
0.12
0.15
0.20
0.25
0.25
0.30
0.30
0.30
0.30
0.45
0.45
0.45
0.8
1.2
1.5
2.0
2.5
3.0
3.0
4.0
4.5
5.5
4.5
5.5
7.5
27000
18000
14000
11000
9000
7800
7000
6000
5500
5000
4600
4200
3400
Table feed
(mm/min)
(IPM)
8400
9000
9500
11000
11000
11000
11000
11000
11000
10000
10000
10000
8800
330.7
354.3
374.0
433.1
433.1
433.1
433.1
433.1
433.1
393.7
393.7
393.7
346.5

ap (mm)
ae (mm)
0.05
0.08
0.12
0.15
0.15
0.15
0.20
0.20
0.20
0.20
0.30
0.30
0.30
0.8
1.2
1.5
2.0
2.5
3.0
3.0
4.0
4.5
5.5
4.5
5.5
7.5
ae
Depth of cut
ap
AISI H13 etc.
AISI D2 etc.
Work material
2
3
4
5
6
7
8
9
10
11
12
13
16
R
(mm)
R
R
R
R
R
R
R
R
R
R
R
R
R
0.5
0.75
1
1.2
1.5
1.5
2
2
2
2
3
3
3
Table feed
(mm/min)
(IPM)
24000
16000
12000
9600
8000
6900
6000
5300
4800
4500
4100
3700
3000
7500
8500
8800
9500
9600
9600
9600
9500
9500
9000
9000
8900
7800

ap (mm)
ae (mm)
295.3
334.6
346.5
374.0
378.0
378.0
378.0
374.0
374.0
354.3
354.3
350.4
307.1
0.04
0.06
0.08
0.10
0.10
0.10
0.15
0.15
0.15
0.15
0.25
0.25
0.25
Revolution
(min-1)
0.8
1.2
1.5
2.0
2.5
3.0
3.0
4.0
4.5
5.5
4.5
5.5
7.5
16000
11000
8000
6400
5300
4600
4000
3800
3200
2900
2700
2500
2000
Table feed
(mm/min)
(IPM)
3000
3300
3500
3800
3800
3800
3800
3800
3800
3500
3500
3500
3200
118.1
129.9
137.8
149.6
149.6
149.6
149.6
149.6
149.6
137.8
137.8
137.8
126.0

ap (mm)
ae (mm)
0.03
0.05
0.07
0.08
0.10
0.10
0.13
0.13
0.13
0.13
0.20
0.20
0.20
0.8
1.2
1.5
2.0
2.5
3.0
3.0
4.0
4.5
5.5
4.5
5.5
7.5
SOLID END MILLS
Dia.
(mm)
Revolution
(min-1)
ae
Depth of cut
ap
y Coefcients respective of tool overhang

Type
Straight
Taper neck
Overhang
Revolution
Feed rate
Depth of cut
ap
L/D < 5
L/D=6
L/D=7
L/D=6
L/D=8
L/D > 10
100%
90%
80%
100%
90%
80%
100%
80%
70%
100%
80%
70%
100%
80%
70%
100%
80%
70%
1) The above table shows cutting conditions when machining with the corner
radius cutting edge.
2) This table shows the cutting conditions with less than 5D overhang length.
In the case of longer overhangs, the revolution and the feed rate should be
reduced proportionately.
4) Using air blow or mist is recommended.
5) When contour milling, cutting conditions can vary greatly due to the
geometry of the workpiece and depth of cut.
6) When machining inclinations in the Z direction, set the inclination angle at
2 and reduce the feed rate by 50%.
7) If the rigidity of the machine or the workpiece installation is very low, or
chattering is generated, please reduce the revolution and the feed rate
proportionately.
VCHFRB
I130
I233
CUTTING CONDITIONS
- Inch sizes
VCHFRB
Carbon steel, Cast iron, Alloy steel ( 30HRC)
Alloy steel, Tool steel, Pre-hardened steel
AISI 1050, AISI 35, AISI P20 etc.
Work material
R
(inch)
Dia.
(inch)
.1250
.1875
.2500
.3750
.5000
R
R
R
R
R
.030
.050
.060
.080
.120
Revolution
(min-1)
21000
14000
10000
6800
5100
Table feed
(mm/min)
(IPM)
11000
13000
13000
13000
12000

ap (inch)
ae (inch)
433
512
512
512
472
.0045
.0075
.0090
.0120
.0180
Revolution
(min-1)
.049
.066
.098
.161
.195
17000
12000
8600
5700
4300
Table feed
(mm/min)
(IPM)
9000
11000
11000
11000
10000
354
433
433
433
394

ap (inch)
ae (inch)
.0032
.0053
.0063
.0084
.0126
.049
.066
.098
.161
.195
ae
Depth of cut
ap
Work material
AISI H13 etc.
R
(inch)
Dia.
(inch)
.1250
.1875
.2500
.3750
.5000
R
R
R
R
R
.030
.050
.060
.080
.120
Revolution
(min-1)
AISI D2 etc.
Table feed
(mm/min)
(IPM)
15000
10000
7600
5000
3800
8500
9300
9600
9500
8900

ap (inch)
ae (inch)
335
366
378
374
350
.0025
.0042
.0050
.0067
.0101
Revolution
(min-1)
.049
.066
.098
.161
.195
10000
6700
5000
3300
2500
Table feed
(mm/min)
(IPM)
3200
3700
3800
3600
3400
126
146
150
142
134

ap (inch)
ae (inch)
.0020
.0034
.0040
.0054
.0081
.049
.066
.098
.161
.195
ae
Depth of cut
ap
SOLID END MILLS
y Coefcients respective of tool overhang
I234
Type
Straight
Taper neck
Overhang
Revolution
Feed rate
Depth of cut
ap
L/D < 5
L/D=6
L/D=7
L/D=6
L/D=8
L/D > 10
100%
90%
80%
100%
90%
80%
100%
80%
70%
100%
80%
70%
100%
80%
70%
100%
80%
70%
1) The above table shows cutting conditions when machining with the corner
radius cutting edge.
2) This table shows the cutting conditions with less than 5D overhang length.
In the case of longer overhangs, the revolution and the feed rate should be
reduced proportionately.
5) When contour milling, cutting conditions can vary greatly due to the
geometry of the workpiece and depth of cut.
6) When machining inclinations in the Z direction, set the inclination angle at
2 and reduce the feed rate by 50%.
7) If the rigidity of the machine or the workpiece installation is very low, or
chattering is generated, please reduce the revolution and the feed rate
proportionately.
VCHFRB
I132
VCMHDRB
y Shoulder milling
Work
material
Dia.
(mm)
2
3
4
5
6
8
10
12
16
20
25


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti -6Al -4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
15000
11000
8000
6400
5900
4400
3500
2900
2200
1800
1400
10000
7400
5600
4500
3700
2800
2300
1900
1400
1100
900
10000
7400
5600
4500
3700
2800
2300
1900
1400
1100
900
550
800
900
1000
1100
1100
1000
1000
800
750
600
21.7
31.5
35.4
39.4
43.3
43.3
39.4
39.4
31.5
29.5
23.6
340
500
540
600
640
660
640
640
500
460
400
13.4
19.7
21.3
23.6
25.2
26.0
25.2
25.2
19.7
18.1
15.7
320
480
520
580
600
600
560
530
450
440
380
12.6
18.9
20.5
22.8
23.6
23.6
22.0
20.9
17.7
17.3
15.0
6400
4800
3600
2900
2400
1800
1400
1200
900
720
570
160
250
270
300
320
330
320
320
250
230
200
6.3
9.8
10.6
11.8
12.6
13.0
12.6
12.6
9.8
9.1
7.9
4800
4000
3200
2600
2100
1600
1300
1100
800
640
510
100
170
240
240
230
220
200
170
130
100
80
3.9
6.7
9.4
9.4
9.1
8.7
7.9
6.7
5.1
3.9
3.1
Depth of
cut
D:Dia.
Work
material
Dia.
(mm)
2
3
4
5
6
8
10
12
16
20
25


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti -6Al -4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
12000
9000
7200
5800
5000
3700
3000
2500
2000
1600
1300
400
600
720
720
800
800
720
720
600
540
480
15.7
23.6
28.3
28.3
31.5
31.5
28.3
28.3
23.6
21.3
18.9
7000
5300
4000
3200
2700
2000
1600
1300
1000
800
640
200
300
360
360
400
400
360
360
280
250
220
7.9
11.8
14.2
14.2
15.7
15.7
14.2
14.2
11.0
9.8
8.7
7000
5300
4000
3200
2700
2000
1600
1300
1000
800
640
100
150
180
180
200
200
180
180
150
130
120
3.9
5.9
7.1
7.1
7.9
7.9
7.1
7.1
5.9
5.1
4.7
4200
3200
2400
1900
1600
1200
960
800
600
480
380
80
130
140
150
160
170
160
160
130
120
100
3.1
5.1
5.5
5.9
6.3
6.7
6.3
6.3
5.1
4.7
3.9
2300
1900
1400
1100
950
720
570
480
360
290
230
40
70
95
95
95
90
80
70
50
40
35
1.6
2.8
3.7
3.7
3.7
3.5
3.1
2.8
2.0
1.6
1.4
SOLID END MILLS
y Slotting
Depth of
cut
D:Dia.
VCMHDRB
I133
I235
CUTTING CONDITIONS
VC4STB
Pre-hardened steel

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
Work material
SOLID END MILLS
R
(mm)
Taper angle Neck

one side length
( )
(mm)
1.5
2
R 0.3
5
10
1.5
1.5
2
R 0.4
5
7
10
1.5
1.5
1.5
2
2
2
5
R 0.5
5
5
7
7
7
10
2
R 0.75
5
1.5
1.5
1.5
2
2
2
R1
5
5
5
7
10
R 1.25 5
1.5
1.5
3
R 1.5
5
5
R 1.75 5
5
5
5
15
10
15
10
10
10
15
10
15
20
10
15
20
10
15
20
10
15
20
14
10
15
10
15
20
6
10
15
10
15
23
17
12
15
15
20
15
10
18
15
Table feed
Revolution
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
32000
32000
32000
32000
32000
27500
1600
1600
1600
1600
2000
2000
2000
2000
2000
2000
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2800
2800
2800
2800
2800
2800
2800
2800
2800
2800
2800
2800
3000
3000
3000
3000
3000
3500
63.0
63.0
63.0
63.0
78.7
78.7
78.7
78.7
78.7
78.7
98.4
98.4
98.4
98.4
98.4
98.4
98.4
98.4
98.4
98.4
98.4
98.4
98.4
98.4
98.4
110.2
110.2
110.2
110.2
110.2
110.2
110.2
110.2
110.2
110.2
110.2
110.2
118.1
118.1
118.1
118.1
118.1
137.8
Depth of cut Depth of cut Revolution

Table feed
ap
ae
-1
(mm)
(mm) (min ) (mm/min) (IPM)
0.08
0.08
0.08
0.05
0.07
0.05
0.07
0.07
0.07
0.06
0.11
0.09
0.06
0.11
0.09
0.06
0.12
0.09
0.08
0.12
0.11
0.08
0.11
0.18
0.16
0.18
0.16
0.14
0.20
0.18
0.16
0.18
0.18
0.14
0.16
0.18
0.23
0.23
0.23
0.23
0.25
0.23
0.23
0.12
0.12
0.12
0.08
0.11
0.08
0.11
0.11
0.11
0.09
0.16
0.14
0.09
0.16
0.14
0.09
0.18
0.14
0.11
0.18
0.16
0.11
0.16
0.27
0.24
0.27
0.24
0.21
0.30
0.27
0.24
0.27
0.27
0.21
0.24
0.27
0.34
0.34
0.34
0.34
0.38
0.34
0.34
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
30000
30000
30000
30000
30000
30000
30000
30000
30000
30000
30000
30000
27000
27000
27000
27000
27000
23000
1200
1200
1200
1200
1500
1500
1500
1500
1500
1500
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1800
1800
1800
1800
1800
1800
1800
1800
1800
1800
1800
1800
2000
2000
2000
2000
2000
2500
47.2
47.2
47.2
47.2
59.1
59.1
59.1
59.1
59.1
59.1
63.0
63.0
63.0
63.0
63.0
63.0
63.0
63.0
63.0
63.0
63.0
63.0
63.0
63.0
63.0
70.9
70.9
70.9
70.9
70.9
70.9
70.9
70.9
70.9
70.9
70.9
70.9
78.7
78.7
78.7
78.7
78.7
98.4

Table feed
ap
ae
-1
(mm)
0.06
0.06
0.06
0.04
0.06
0.04
0.06
0.06
0.06
0.05
0.08
0.07
0.05
0.08
0.07
0.05
0.10
0.07
0.06
0.10
0.08
0.06
0.08
0.14
0.13
0.14
0.13
0.11
0.16
0.14
0.13
0.14
0.14
0.11
0.13
0.14
0.18
0.18
0.18
0.18
0.20
0.18
0.18
0.10
0.10
0.10
0.06
0.08
0.06
0.08
0.08
0.08
0.07
0.13
0.11
0.07
0.13
0.11
0.07
0.14
0.11
0.09
0.14
0.13
0.09
0.13
0.22
0.19
0.22
0.19
0.17
0.24
0.22
0.19
0.22
0.22
0.17
0.19
0.22
0.27
0.27
0.27
0.27
0.30
0.27
0.27
40000
40000
40000
40000
30000
30000
30000
30000
30000
30000
25000
25000
25000
25000
25000
25000
25000
25000
25000
25000
25000
25000
25000
18000
18000
15000
15000
15000
15000
15000
15000
15000
15000
15000
15000
15000
15000
16000
16000
16000
16000
16000
14000
700
700
700
700
700
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1200
1200
1200
1200
1200
1500
27.6
27.6
27.6
27.6
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
39.4
39.4
39.4
39.4
39.4
39.4
39.4
39.4
39.4
39.4
39.4
39.4
47.2
47.2
47.2
47.2
47.2
59.1

ap
ae
(mm)
(mm)
0.04
0.04
0.04
0.03
0.04
0.03
0.04
0.04
0.04
0.03
0.05
0.05
0.03
0.05
0.05
0.03
0.06
0.05
0.04
0.06
0.05
0.04
0.05
0.09
0.08
0.09
0.08
0.07
0.10
0.09
0.08
0.09
0.09
0.07
0.08
0.09
0.11
0.11
0.11
0.11
0.13
0.11
0.11
0.06
0.06
0.06
0.04
0.05
0.04
0.05
0.05
0.05
0.05
0.08
0.07
0.05
0.08
0.07
0.05
0.09
0.07
0.06
0.09
0.08
0.06
0.08
0.14
0.12
0.14
0.12
0.11
0.15
0.14
0.12
0.14
0.14
0.11
0.12
0.14
0.17
0.17
0.17
0.17
0.19
0.17
0.17
Depth of cut
I236
I135
VC4STB

Pre-hardened steel

AISI P21 etc.
AISI H13 etc.
AISI D2 etc
.
Work material
R
(mm)
R2
R3
R4
Taper angle Neck

one side length
(mm)
( )
1.5
1.5
3
5
7
1.5
1.5
3
1.5
3
15
20
21
13
18
15
20
22
15
22
Table feed
Revolution
24000
24000
24000
24000
24000
16000
16000
16000
12000
12000
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
137.8
137.8
137.8
137.8
137.8
137.8
137.8
137.8
137.8
137.8

Table feed
ap
ae
-1
(mm)
0.23
0.23
0.23
0.25
0.23
0.30
0.30
0.30
0.30
0.30
0.34
0.34
0.34
0.38
0.34
0.45
0.45
0.45
0.45
0.45
20000
20000
20000
20000
20000
13500
13500
13500
10000
10000
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
98.4
98.4
98.4
98.4
98.4
98.4
98.4
98.4
98.4
98.4

Table feed
ap
ae
-1
(mm)
0.18
0.18
0.18
0.20
0.18
0.24
0.24
0.24
0.24
0.24
0.27
0.27
0.27
0.30
0.27
0.36
0.36
0.36
0.36
0.36
12000
12000
12000
12000
12000
8000
8000
8000
6000
6000
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
59.1
59.1
59.1
59.1
59.1
59.1
59.1
59.1
59.1
59.1

ap
ae
(mm)
(mm)
0.11
0.11
0.11
0.13
0.11
0.15
0.15
0.15
0.15
0.15
0.17
0.17
0.17
0.19
0.17
0.23
0.23
0.23
0.23
0.23
Depth of cut
SOLID END MILLS
I237
CUTTING CONDITIONS
VC2C
Work
material


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti -6Al -4V etc.
AISI H13 etc.
Dia.
(mm)
Revolution
(min-1)
2
4
6
8
10
12
16000
8000
5300
4000
3200
2700
Depth of
cut
Table feed
(mm/min)
(IPM)
960
480
320
240
190
160
37.8
18.9
12.6
9.4
7.5
6.3
Revolution
(min-1)
11000
5600
3700
2800
2200
1900
Table feed
(mm/min)
(IPM)
590
300
200
150
120
100
23.2
11.8
7.9
5.9
4.7
3.9
Revolution
(min-1)
9500
4800
3200
2400
1900
1600
Table feed
(mm/min)
(IPM)
460
230
150
120
90
80
18.1
9.1
5.9
4.7
3.5
3.1
Revolution
(min-1)
8000
4000
2700
2000
1600
1300
Table feed
(mm/min)
(IPM)
320
160
110
80
60
50
12.6
6.3
4.3
3.1
2.4
2.0
Chamfering of hole
Chamfering
(MAX. 2.5mm)
D:Dia.
SOLID END MILLS
I238
VC2C
I137
VF2XL
End mill, 2 ute, Long neck
AISI H13 etc.
AISI D2 etc.
Table feed
Table feed
Dia.
(mm)
Neck length
(mm)
Revolution
(min-1)
(mm/min)
(IPM)

ap (mm)
Revolution
(min-1)
(mm/min)
(IPM)

ap (mm)
0.1
0.5
0.6
1
1.5
1
2
3
1
2
4
2
4
6
2
4
6
4
6
8
10
4
6
8
10
12
6
8
10
12
16
6
8
10
12
16
20
12
16
20
40000
40000
40000
40000
40000
40000
38000
40000
40000
36000
40000
36000
30000
40000
36000
30000
36000
30000
24000
20000
32000
32000
28000
28000
24000
22000
22000
22000
20000
18000
16000
16000
16000
16000
15000
14000
11000
11000
11000
100
400
300
200
500
400
250
800
500
300
800
600
400
1000
800
600
1200
900
600
400
1600
1400
1000
800
500
1200
1100
1000
800
500
1000
1000
800
800
600
500
800
600
500
3.9
15.7
11.8
7.9
19.7
15.7
9.8
31.5
19.7
11.8
31.5
23.6
15.7
39.4
31.5
23.6
47.2
35.4
23.6
15.7
63.0
55.1
39.4
31.5
19.7
47.2
43.3
39.4
31.5
19.7
39.4
39.4
31.5
31.5
23.6
19.7
31.5
23.6
19.7
0.002
0.004
0.003
0.002
0.006
0.003
0.002
0.008
0.007
0.004
0.01
0.008
0.005
0.015
0.01
0.006
0.03
0.02
0.01
0.008
0.05
0.04
0.03
0.02
0.02
0.08
0.07
0.06
0.05
0.03
0.15
0.15
0.1
0.08
0.06
0.05
0.2
0.15
0.1
40000
40000
40000
40000
40000
38000
36000
36000
30000
27000
30000
27000
22000
30000
27000
22000
27000
22000
18000
15000
24000
24000
21000
21000
18000
16000
16000
16000
15000
13000
12000
12000
12000
12000
11000
10000
8200
8200
8200
80
360
250
150
450
350
200
500
350
200
600
450
300
700
500
350
900
650
450
300
1100
1000
750
600
370
900
800
750
600
350
750
750
600
600
450
350
600
450
350
3.1
14.2
9.8
5.9
17.7
13.8
7.9
19.7
13.8
7.9
23.6
17.7
11.8
27.6
19.7
13.8
35.4
25.6
17.7
11.8
43.3
39.4
29.5
23.6
14.6
35.4
31.5
29.5
23.6
13.8
29.5
29.5
23.6
23.6
17.7
13.8
23.6
17.7
13.8
0.001
0.004
0.002
0.001
0.004
0.002
0.001
0.006
0.005
0.003
0.009
0.007
0.004
0.012
0.01
0.006
0.02
0.015
0.008
0.005
0.04
0.03
0.02
0.015
0.01
0.06
0.05
0.04
0.03
0.02
0.15
0.1
0.08
0.06
0.05
0.04
0.15
0.15
0.1
0.2
0.3
0.4
0.5
0.6
0.8
1.5
SOLID END MILLS
Work material
Depth of cut
D:Dia.
VF2XL
I138
I239
CUTTING CONDITIONS
VF2MV
Work
material

Pre-hardened steel
AISI H13, AISI W1 10,

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
Table feed
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
0.5
1
1.5
2
2.5
3
4
5
6
40000
40000
40000
30000
24000
20000
15000
12000
10000
1000
2000
3000
3000
2600
2300
2000
1600
1400

(mm)
(min-1)
39.4
78.7
118.1
118.1
102.4
90.6
78.7
63.0
55.1
0.015
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
<Please
Depth of
cut
40000
32000
32000
24000
19000
16000
12000
9000
7000
Table feed
(IPM)
(mm/min)
960
1600
1900
1900
1600
1400
1200
900
700

1D
37.8
63.0
74.8
74.8
63.0
55.1
47.2
35.4
27.6

(mm)
(min-1)
0.015
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
30000
16000
10600
8100
6400
5400
4000
3200
2700
Table feed
(IPM)
(mm/min)
600
550
500
400
350
300
240
190
160
23.6
21.7
19.7
15.7
13.8
11.8
9.4
7.5
6.3
Depth of cut
(mm)
0.01
0.05
0.08
0.1
0.13
0.15
0.2
0.2
0.2
D
<Please
D:Dia.
SOLID END MILLS
1) When slotting, reduce the revolutions by 50 - 70% and the feed rate by 40 - 60%.
2) For austenitic stainless steels, titanium and heat-resistant alloys, VFMHV is recommended.
3) The irregular helix ute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity
of the machine or the workpiece installation is very low, then vibration can occur. In this case, please reduce the revolution and feed rate
proportionately, or set a lower depth of cut.
I240
VF2MV
I140
VF4MV
Work
material

Pre-hardened steel

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
Table feed
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
6
8
10
12
16
20
10000
8000
6400
5400
2400
1900
2100
1500
1400
1200
550
480
82.7
59.1
55.1
47.2
21.7
18.9

(mm)
(min-1)
0.60
0.80
1.00
1.00
3.00
4.00
<Please
Depth of
cut
7000
5600
4500
3800
1200
1000
Table feed
(IPM)
(mm/min)
1400
1100
950
860
280
240
55.1
43.3
37.4
33.9
11.0
9.4

(mm)
(min-1)
0.30
0.40
0.50
0.50
0.80
1.00
2700
2000
1600
1300
1000
800
Table feed
(IPM)
(mm/min)
320
240
210
160
130
100
12.6
9.4
8.3
6.3
5.1
3.9
Depth of cut
(mm)
0.20
0.20
0.30
0.30
0.30
0.30
<Please
D:Dia.
SOLID END MILLS
1) When slotting, reduce the revolutions by 50 - 70% and the feed rate by 40 - 60%.
2) For austenitic stainless steels, titanium and heat-resistant alloys, VFMHV is recommended.
VF4MV
I141
I241
CUTTING CONDITIONS
VFMHV
Medium cut length, Irregular helix utes
VFMHVRB
Corner radius end mill, Medium cut length, 4 ute, Irregular helix utes
y Shoulder milling
Work
material
Dia.
(mm)
2
3
4
5
6
7
8
9
10
11
12
13
14
16
18
20


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti-6Al-4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
21000
15000
11000
9600
8000
6800
6000
5300
4800
4400
4000
3700
3400
3000
2700
2400
1100
1250
1400
1920
2240
1900
1680
1480
1440
1350
1250
1180
1160
1140
970
860
43.3
49.2
55.1
75.6
88.2
74.8
66.1
58.3
56.7
53.1
49.2
46.5
45.7
44.9
38.2
33.9
21000
15000
11000
9600
8000
6800
6000
5300
4800
4400
4000
3700
3400
3000
2700
2400
1100
1250
1400
1920
2240
1900
1680
1480
1440
1350
1250
1180
1160
1140
970
860
43.3
49.2
55.1
75.6
88.2
74.8
66.1
58.3
56.7
53.1
49.2
46.5
45.7
44.9
38.2
33.9
14000
10600
8000
6400
5300
4500
4000
3500
3200
2900
2700
2500
2300
2000
1800
1600
560
850
960
1020
1060
1010
960
840
770
760
760
700
640
560
550
510
22.0
33.5
37.8
40.2
41.7
39.8
37.8
33.1
30.3
29.9
29.9
27.6
25.2
22.0
21.7
20.1
9600
7400
5600
4500
3700
3200
2800
2500
2200
2000
1900
1700
1600
1400
1200
1100
310
380
400
430
440
450
450
450
440
400
380
360
350
340
340
330
12.2
15.0
15.7
16.9
17.3
17.7
17.7
17.7
17.3
15.7
15.0
14.2
13.8
13.4
13.4
13.0
4800
4200
3200
2500
2100
1800
1600
1400
1300
1200
1100
1000
900
800
700
600
130
200
220
250
250
260
260
220
210
190
180
160
140
130
110
100
5.1
7.9
8.7
9.8
9.8
10.2
10.2
8.7
8.3
7.5
7.1
6.3
5.5
5.1
4.3
3.9
Depth of
cut
D:Dia.
y Slotting
SOLID END MILLS
Work
material
Dia.
(mm)
2
3
4
5
6
7
8
9
10
11
12
13
14
16
18
20


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti-6Al-4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
17000
12000
9200
7600
6400
5500
4800
4200
3800
3500
3200
2900
2700
2400
2100
1900
680
720
810
1060
1280
1210
1150
1010
910
900
900
810
760
670
670
610
26.8
28.3
31.9
41.7
50.4
47.6
45.3
39.8
35.8
35.4
35.4
31.9
29.9
26.4
26.4
24.0
10000
6900
5600
4500
3700
3200
2800
2500
2200
2000
1900
1700
1600
1400
1200
1100
400
410
490
630
740
700
670
600
530
530
530
480
450
390
380
350
15.7
16.1
19.3
24.8
29.1
27.6
26.4
23.6
20.9
20.9
20.9
18.9
17.7
15.4
15.0
13.8
9600
7400
5600
4500
3700
3200
2800
2500
2200
2000
1900
1700
1600
1400
1200
1100
310
380
400
410
440
410
390
350
350
320
300
290
290
280
270
260
12.2
15.0
15.7
16.1
17.3
16.1
15.4
13.8
13.8
12.6
11.8
11.4
11.4
11.0
10.6
10.2
4800
3200
2400
1900
1600
1400
1200
1100
1000
900
800
730
680
600
530
480
130
140
150
170
190
190
190
180
160
160
160
150
140
120
120
120
5.1
5.5
5.9
6.7
7.5
7.5
7.5
7.1
6.3
6.3
6.3
5.9
5.5
4.7
4.7
4.7
3200
2700
2000
1600
1300
1100
1000
900
800
720
660
610
570
500
440
400
80
110
120
130
160
140
130
130
130
120
110
100
90
80
70
60
3.1
4.3
4.7
5.1
6.3
5.5
5.1
5.1
5.1
4.7
4.3
3.9
3.5
3.1
2.8
2.4
Depth of
cut
D:Dia.
I242
VFMHV
I142
VFMHVRB
I173
VFJHV
End mill, Semi long cut length, 4 ute, Irregular helix utes
y Shoulder milling
Work
material
Dia.
(mm)
2
3
4
5
6
8
10
12
16
20


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti-6Al-4V etc.
AISI D2 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
16000
12000
9500
7600
6300
4700
3800
3100
2300
1900
530
820
950
1000
1100
1100
1000
980
810
740
20.9
32.3
37.4
39.4
43.3
43.3
39.4
38.6
31.9
29.1
10000
7600
6000
4800
4000
3000
2400
2000
1500
1200
320
470
520
550
610
630
610
580
480
430
12.6
18.5
20.5
21.7
24.0
24.8
24.0
22.8
18.9
16.9
10000
7600
6000
4800
4000
3000
2400
2000
1500
1200
300
440
510
540
600
600
570
520
420
390
11.8
17.3
20.1
21.3
23.6
23.6
22.4
20.5
16.5
15.4
7400
5600
4500
3600
3000
2200
1800
1500
1100
900
140
280
310
330
330
330
310
280
240
220
5.5
11.0
12.2
13.0
13.0
13.0
12.2
11.0
9.4
8.7
3800
2500
1900
1500
1300
960
760
640
480
380
55
80
110
110
110
100
100
80
65
50
2.2
3.1
4.3
4.3
4.3
3.9
3.9
3.1
2.6
2.0
Depth of
cut
D:Dia.
SOLID END MILLS
VFJHV
I144
I243
CUTTING CONDITIONS
VF6MHV
VF6MHVRB
End mill, Medium cut length, 6 ute, Irregular helix utes Corner radius, Medium cut length, 6 ute, Irregular helix utes
ySide milling
Pre-hardened steel
Work
material AISI H13, AISI W1-10,
AISI P21 etc.
Table feed

Titanium alloy
AISI 304, AISI 306,

Ti-6Al-4V etc.
Inconel718 etc.
Table feed
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
Revolution
(min-1)
(mm/min)
(IPM)
6
8
10
12
16
20
10600
8000
6400
5300
4000
3200
2900
2900
2700
2700
2200
1900
114.2
114.2
106.3
106.3
86.6
74.8
8000
6000
4800
4000
3000
2400
2000
2000
2000
2000
1600
1400
78.7
78.7
78.7
78.7
63.0
55.1
2100
1600
1300
1100
800
640
320
300
260
230
180
150
12.6
11.8
10.2
9.1
7.1
5.9
Depth of
cut
D:Dia.
SOLID END MILLS
I244
VF6MHV
I145
VF6MHVRB
I175
MS2XLRB
VFSD
VFMD
Corner
End
mill,radius
Short cut
endlength,
mill, Short
For hardened
cut length,
materials
2 ute, Long
End mill,
neckMedium cut length, For hardened materials
Work
material
AISI H13 etc.
AISI D2 etc.
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
1
2
3
4
6
8
10
12
16
20
25
40000
40000
32000
24000
16000
12000
9600
8000
6000
4800
3800
1200
2000
3800
4400
5800
5800
5800
4800
3600
2900
2300
47.2
78.7
149.6
173.2
228.3
228.3
228.3
189.0
141.7
114.2
90.6

(min-1)
ae (mm)
0.05
0.1
0.2
0.2
0.3
0.4
0.5
0.6
0.8
1.0
1.0
40000
24000
16000
12000
8000
6000
4800
4000
3000
2400
1900
Table feed
(mm/min)
(IPM)
800
1000
1900
2200
2900
2900
2900
2400
1800
1400
1100
31.5
39.4
74.8
86.6
114.2
114.2
114.2
94.5
70.9
55.1
43.3

(min-1)
ae (mm)
0.03
0.05
0.1
0.1
0.2
0.2
0.3
0.3
0.5
0.5
0.5
32000
16000
11000
8000
5300
4000
3200
2700
2000
1600
1300
Table feed
(mm/min)
(IPM)
Depth of cut
ae (mm)
500
600
1200
1300
1800
1800
1800
1500
1100
880
720
19.7
23.6
47.2
51.2
70.9
70.9
70.9
59.1
43.3
34.6
28.3
0.02
0.05
0.05
0.05
0.1
0.1
0.2
0.2
0.3
0.3
0.3
Depth of
cut
D:Dia.
Work
material
AISI H13 etc.
AISI D2 etc.
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
1
2
15000
8000
300
320
11.8
12.6

(min-1)
ap (mm)
0.1
0.2
9500
4800
Table feed
(mm/min)
(IPM)
Depth of cut
ap (mm)
110
190
4.3
7.5
0.05
0.1
SOLID END MILLS
y Slot milling with small diameter tools
Depth of
cut
D:Dia.
VFSD
I148
VFMD
I149
I245
CUTTING CONDITIONS
VFSFPR
ySide milling
Work
material
Dia.
(mm)
3
4
5
6
8
10
12
16
20


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti 6Al 4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
16000
12000
9500
8000
6000
4800
4000
3000
2400
960
960
960
960
1050
1050
960
840
760
37.8
37.8
37.8
37.8
41.3
41.3
37.8
33.1
29.9
13000
9500
7600
6400
4800
3800
3200
2400
1900
640
640
640
680
760
760
700
620
560
25.2
25.2
25.2
26.8
29.9
29.9
27.6
24.4
22.0
6400
4800
3800
3200
2400
1900
1600
1200
1000
260
260
260
290
340
340
320
300
300
10.2
10.2
10.2
11.4
13.4
13.4
12.6
11.8
11.8
5300
4000
3200
2700
2000
1600
1300
1000
800
320
320
320
340
400
400
400
360
320
12.6
12.6
12.6
13.4
15.7
15.7
15.7
14.2
12.6
4200
3200
2500
2100
1600
1300
1100
800
600
70
70
70
75
95
105
110
110
100
2.8
2.8
2.8
3.0
3.7
4.1
4.3
4.3
3.9
Depth of
cut
D:Dia.
y Slotting
SOLID END MILLS
Work
material
Dia.
(mm)
3
4
5
6
8
10
12
16
20


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti 6Al 4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
13000
9500
7600
6400
4800
3800
3200
2400
1900
720
720
720
720
800
800
750
620
540
28.3
28.3
28.3
28.3
31.5
31.5
29.5
24.4
21.3
11000
8000
6400
5300
4000
3200
2700
2000
1600
480
480
480
480
520
520
520
450
400
18.9
18.9
18.9
18.9
20.5
20.5
20.5
17.7
15.7
4800
3600
3200
2700
2000
1600
1300
1000
800
190
190
190
200
220
220
210
180
160
7.5
7.5
7.5
7.9
8.7
8.7
8.3
7.1
6.3
3200
2400
1900
1600
1200
1000
800
600
500
190
190
190
200
220
220
210
180
160
7.5
7.5
7.5
7.9
8.7
8.7
8.3
7.1
6.3
2100
1600
1300
1100
800
600
500
400
300
25
25
25
30
35
35
40
45
40
1.0
1.0
1.0
1.2
1.4
1.4
1.6
1.8
1.6
Depth of
cut
D:Dia.
I246
VFSFPR
I150
VFMFPR
Roughing end mill, Medium cut length, 4 ute
ySide milling
Work
material
Dia.
(mm)
5
6
8
10
12
16
20


Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306,

Ti 6Al 4V etc.
AISI H13 etc.
Inconel718 etc.
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
Table feed
Revolution
3800
3200
2400
1900
1600
1200
1000
360
360
450
450
400
360
340
14.2
14.2
17.7
17.7
15.7
14.2
13.4
3200
2700
2000
1600
1300
1000
800
290
290
360
360
320
290
270
11.4
11.4
14.2
14.2
12.6
11.4
10.6
2500
2100
1600
1300
1100
800
600
150
160
160
180
180
160
150
5.9
6.3
6.3
7.1
7.1
6.3
5.9
2500
2100
1600
1300
1100
800
600
150
160
160
180
180
160
150
5.9
6.3
6.3
7.1
7.1
6.3
5.9
1900
1600
1200
1000
800
600
500
50
60
70
75
80
80
80
2.0
2.4
2.8
3.0
3.1
3.1
3.1
Depth of
cut
D:Dia.
SOLID END MILLS
VFMFPR
I153
I247
CUTTING CONDITIONS
VF2WB
Wide ball nose, Medium cut length, 2 ute
Work
material

Pre-hardened steel

Titanium alloy
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI 304, AISI 306, Ti 6Al 4V etc. AISI H13 etc.
R
(mm)
Table feed
Revolution
R1
R1.5
R2
R3
40000
32000
24000
16000
Depth of
cut

5000
5000
3800
2800
196.9
196.9
149.6
110.2
Table feed
(mm)
0.07
0.12
0.15
0.20
40000
32000
24000
16000
5000
5000
3800
2800
196.9
196.9
149.6
110.2
Table feed
(mm)
0.06
0.11
0.13
0.18
32000
26000
20000
13000
2500
2500
2000
1500
98.4
98.4
98.4
59.1
Table feed
(mm)
0.05
0.10
0.12
0.15
32000
26000
20000
13000
3000
3000
2800
2100
118.1
118.1
110.2
82.7
Depth of cut
(mm)
0.03
0.07
0.10
0.12
0.05R (R=1)
0.1R (R > 1)
<Please
R:Radius
SOLID END MILLS
I248
VF2WB
I154
VF2SSB
VF2SB
Work
material
R
(mm)
R 0.1
R 0.15
R 0.2
R 0.3
R 0.4
R 0.5
R 0.75
R 1
R 1.25
R 1.5
R 2
R 2.5
R 3
R 4
R 5
R 6
R 8
R10
AISI H13 etc.
AISI D2 etc.
% < 15
% >15
Table feed
Revolution
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
32000
25000
21000
16000
13000
9000
6000
4500
320
640
1600
3200
6400
8000
9600
9600
10400
12000
10880
9000
8400
6400
5200
3600
2400
1800
12.6
25.2
63.0
126.0
252.0
315.0
378.0
378.0
409.4
472.4
428.3
354.3
330.7
252.0
204.7
141.7
94.5
70.9
Table feed
Revolution
40000
40000
40000
40000
40000
40000
40000
39000
32000
27000
20000
16000
13000
10000
8000
6000
4000
3000
240
560
1200
1600
2400
3200
4000
4700
4500
4300
3600
2900
2600
2000
1700
1300
1000
780
9.4
22.0
47.2
63.0
94.5
126.0
157.5
185.0
177.2
169.3
141.7
114.2
102.4
78.7
66.9
51.2
39.4
30.7
% < 15
Depth of
cut
Table feed
Revolution
ap (mm)
0.003
0.01
0.02
0.03
0.05
0.06
0.09
0.11
0.12
0.13
0.15
0.2
0.25
0.3
0.5
0.5
0.5
0.5
40000
40000
40000
40000
40000
40000
40000
40000
37000
32000
24000
19000
16000
12000
10000
7000
5000
4000
320
640
1400
2800
4000
5600
7200
8000
8100
7700
6200
5300
4800
3600
3200
2200
1600
1300
12.6
25.2
55.1
110.2
157.5
220.5
283.5
315.0
318.9
303.1
244.1
208.7
189.0
141.7
126.0
86.6
63.0
51.2
% >15
Table feed
Revolution
40000
40000
40000
40000
40000
40000
32000
24000
19000
16000
12000
9600
8000
6000
4800
3600
2500
1800
160
400
1000
1200
1600
2400
2500
2400
2300
2200
1900
1700
1600
1200
960
720
500
360
6.3
15.7
39.4
47.2
63.0
94.5
98.4
94.5
90.6
86.6
74.8
66.9
63.0
47.2
37.8
28.3
19.7
14.2
Depth of
cut
ap (mm)
0.003
0.007
0.015
0.025
0.04
0.05
0.075
0.1
0.11
0.12
0.13
0.15
0.2
0.2
0.2
0.3
0.3
0.3
< 0.2R
Depth of
cut
ap
R:Radius
R
(mm)
R 0.1
R 0.15
R 0.2
R 0.3
R 0.4
R 0.5
R 0.75
R 1
R 1.25
R 1.5
R 2
R 2.5
R 3
R 4
R 5
R 6
R 8
R10

% < 15
% >15
Table feed
Revolution
40000
40000
40000
40000
40000
40000
32000
24000
19000
16000
12000
9600
8000
6000
4800
3600
2500
1800
320
640
1200
2000
2800
3600
4500
3800
3400
3200
2400
2100
1700
1400
1100
860
650
470
12.6
25.2
47.2
78.7
110.2
141.7
177.2
149.6
133.9
126.0
94.5
82.7
66.9
55.1
43.3
33.9
25.6
18.5
Table feed
Revolution
40000
40000
40000
40000
40000
32000
21000
16000
13000
11000
8000
6000
5000
4000
3000
2200
1500
1000
160
400
1000
1200
1600
1300
1200
1000
1000
880
800
600
600
480
420
310
240
160
6.3
15.7
39.4
47.2
63.0
51.2
47.2
39.4
39.4
34.6
31.5
23.6
23.6
18.9
16.5
12.2
9.4
6.3
SOLID END MILLS
Work
material
Depth of
cut
ap (mm)
0.002
0.005
0.01
0.02
0.03
0.04
0.05
0.07
0.08
0.09
0.1
0.1
0.11
0.11
0.12
0.12
0.15
0.15

2) If the depth of cut is smaller than this table, feed rate can
be increased.
3) If the rigidity of the machine or the workpiece installation
is very low, or chattering is generated, please reduce the
revolution and the feed rate proportionately.
< 0.2R
Depth of
cut
ap
R:Radius
VF2SSB
I155
VF2SB
I156
I249
CUTTING CONDITIONS
VF2SDB
VF2SDBL
yOverhang below 5D (D is end mill diameter)
Work
material
R
(mm)
R 0.5
R 1 1, 3
R 1.5 2
R 1.5 1
R 2 3
R 2 1
R 2.5
R 3
R 4
R 5
R 6
R 8
R10

Pre-hardened steel

AISI P21 etc.
AISI H13 etc.
% >15
% < 15
Table feed
Table feed
Revolution
(min-1) (mm/min)
(IPM)
Revolution
(min-1) (mm/min)
(IPM)
40000
40000
29000
37000
24000
30000
25000
22000
19000
15000
12000
9000
7500
204.7
236.2
181.1
275.6
169.3
255.9
236.2
236.2
204.7
169.3
133.9
102.4
86.6
36000
36000
19000
24000
15000
19000
16000
14000
12000
9500
8000
6000
4800
90.6
137.8
94.5
118.1
86.6
110.2
102.4
94.5
86.6
78.7
70.9
59.1
47.2
5200
6000
4600
7000
4300
6500
6000
6000
5200
4300
3400
2600
2200
2300
3500
2400
3000
2200
2800
2600
2400
2200
2000
1800
1500
1200
%< 15
ap
ae
Table feed
Revolution
(mm)
(mm)
0.10
0.20
0.20
0.30
0.25
0.40
0.50
0.60
0.80
1.00
1.20
1.60
2.00
0.25
0.50
0.50
0.75
0.70
1.00
1.30
1.80
2.40
3.00
3.60
4.80
6.00
40000
40000
25000
37000
19000
28000
22000
18000
15000
11000
9000
7000
5500
5200
6000
4000
7000
3400
6000
5000
4500
3800
3000
2400
1900
1500
204.7
236.2
157.5
275.6
133.9
236.2
196.9
177.2
149.6
118.1
94.5
74.8
59.1
% >15
Table feed
Revolution
(min-1) (mm/min)
(IPM)
36000
36000
16000
24000
13000
19000
16000
12000
9500
7000
6000
4500
3600
90.6
137.8
78.7
118.1
66.9
102.4
90.6
74.8
66.9
59.1
55.1
43.3
35.4
2300
3500
2000
3000
1700
2600
2300
1900
1700
1500
1400
1100
900

ap
ae
(mm)
(mm)
0.10
0.20
0.20
0.30
0.25
0.40
0.50
0.60
0.80
1.00
1.20
1.60
2.00
0.25
0.50
0.50
0.75
0.70
1.00
1.25
1.50
2.00
2.50
3.00
4.00
5.00
ae
Depth of
cut
< ap
1: Shank Dia. = 6 mm, 2: Shank Dia. = 3 mm, 3: Shank Dia. = 4 mm
SOLID END MILLS

Work
material
R
(mm)
R 0.5
R 1 1, 3
R 1.5 2
R 1.5 1
R 2 3
R 2 1
R 2.5
R 3
R 4
R 5
R 6
R 8
R10
AISI D2 etc.
% >15
% < 15
Table feed
Revolution
(min-1) (mm/min)
(IPM)
Table feed
Revolution
40000
36000
17000
25000
12000
18000
15000
12000
9800
7500
6000
4500
3600
196.9
196.9
94.5
236.2
74.8
189.0
165.4
137.8
118.1
94.5
74.8
59.1
47.2
40000
24000
11000
16000
8200
12000
9500
8000
6500
5000
4000
3000
2500
5000
5000
2400
6000
1900
4800
4200
3500
3000
2400
1900
1500
1200
2400
2400
1000
2200
900
2000
1700
1600
1300
1000
800
600
500
94.5
94.5
39.4
86.6
35.4
78.7
66.9
63.0
51.2
39.4
31.5
23.6
19.7

ap
ae
(mm)
(mm)
0.05
0.10
0.12
0.12
0.13
0.13
0.15
0.20
0.20
0.20
0.30
0.30
0.30
0.10
0.20
0.30
0.30
0.40
0.40
0.50
0.60
0.80
1.00
1.20
1.60
2.00

2) If the depth of cut is smaller than this table, feed rate can be
increased.
ae
Depth of
cut
< ap
1: Shank Dia. = 6 mm, 2: Shank Dia. = 3 mm, 3: Shank Dia. = 4 mm
I250
VF2SDB
I157
VF2SDBL
I158
Work
material
AISI H13 etc.
AISI D2 etc.
Neck Revolution
Table feed
R
length
(mm) (mm) (min-1) (mm/min) (IPM)

Table feed
ap
-1
Depth of cut
ap
(mm)
0.5
1
1.5
R 0.1
2
2.5
1
1.5
R 0.15 2
2.5
3
4
1
1.5
2
2.5
R 0.2
3
4
5
1.5
2
R 0.25 3
4
5
6
2
3
4
5
R 0.3
6
7
8
2
3
4
R 0.4
6
8
10
3
4
5
6
8
R 0.5 10
12
14
16
18
20
6
8
R 0.6 10
12
14
16
8
R 0.7 12
16
6
8
R 0.75 10
12
14
16
0.003
0.002
0.001
0.001
0.001
0.007
0.005
0.003
0.003
0.002
0.002
0.015
0.01
0.01
0.005
0.005
0.004
0.003
0.02
0.02
0.015
0.01
0.007
0.006
0.03
0.03
0.02
0.01
0.008
0.008
0.006
0.04
0.04
0.02
0.02
0.01
0.008
0.05
0.05
0.03
0.03
0.02
0.01
0.01
0.008
0.008
0.005
0.005
0.05
0.05
0.03
0.02
0.01
0.01
0.06
0.03
0.02
0.07
0.07
0.06
0.04
0.04
0.03
0.002
0.002
0.001
0.001
0.001
0.005
0.003
0.002
0.002
0.001
0.001
0.01
0.006
0.006
0.003
0.003
0.003
0.002
0.015
0.015
0.01
0.007
0.005
0.004
0.02
0.02
0.015
0.007
0.005
0.005
0.004
0.03
0.03
0.015
0.01
0.007
0.005
0.04
0.04
0.02
0.02
0.01
0.01
0.008
0.008
0.006
0.004
0.004
0.04
0.04
0.02
0.01
0.01
0.006
0.05
0.02
0.01
0.06
0.06
0.04
0.03
0.03
0.02
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
30000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
36000
36000
36000
40000
40000
35000
30000
30000
30000
25000
40000
40000
40000
30000
25000
25000
40000
40000
40000
35000
30000
20000
20000
18000
18000
13000
13000
40000
40000
27000
16000
16000
15000
40000
32000
15000
40000
40000
40000
32000
16000
13000
300
300
300
200
100
500
500
500
400
300
200
1400
1000
1000
700
700
600
400
2000
2000
1200
900
700
600
2800
2800
2000
1000
800
600
400
3500
3000
3000
1600
1000
600
4000
4000
3000
2000
1600
1000
1000
600
500
300
250
4000
3000
1900
1100
850
500
4500
3000
1000
5000
5000
4500
3400
1500
1200
11.8
11.8
11.8
7.9
3.9
19.7
19.7
19.7
15.7
11.8
7.9
55.1
39.4
39.4
27.6
27.6
23.6
15.7
78.7
78.7
47.2
35.4
27.6
23.6
110.2
110.2
78.7
39.4
31.5
23.6
15.7
137.8
118.1
118.1
63.0
39.4
23.6
157.5
157.5
118.1
78.7
63.0
39.4
39.4
23.6
19.7
11.8
9.8
157.5
118.1
74.8
43.3
33.5
19.7
177.2
118.1
39.4
196.9
196.9
117.2
133.9
59.1
47.2
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
30000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
36000
36000
36000
40000
40000
35000
30000
30000
30000
25000
40000
40000
40000
30000
25000
25000
40000
40000
40000
35000
30000
20000
18000
18000
18000
13000
13000
35000
27000
24000
16000
16000
14000
28000
19000
14000
32000
28000
21000
19000
13000
13000
300
300
200
100
60
500
500
500
400
300
200
1400
1000
1000
700
700
500
300
2000
2000
1200
900
600
500
2800
2800
2000
1000
800
600
400
3500
3000
3000
1600
1000
600
4000
4000
3000
2000
1600
1000
800
480
400
240
200
3500
2000
1700
1000
780
400
3200
1800
800
4000
3500
2400
2000
1200
1200
11.8
11.8
7.9
3.9
2.4
19.7
19.7
19.7
15.7
11.8
7.9
55.1
39.4
39.4
27.6
27.6
19.7
11.8
78.7
78.7
47.2
35.4
23.6
19.7
110.2
110.2
78.7
39.4
31.5
23.6
15.7
137.8
118.1
118.1
63.0
39.4
23.6
157.5
157.5
118.1
78.7
63.0
39.4
31.5
18.9
15.7
9.4
7.9
137.8
78.7
66.9
39.4
30.7
15.7
126.0
70.9
31.5
157.5
137.8
94.5
78.7
47.2
47.2
Work
material
AISI H13 etc.
AISI D2 etc.
Neck Revolution
Table feed
R
length
(mm) (mm) (min-1) (mm/min) (IPM)
R 0.75
R 0.8
R 0.9
R1
R 1.25
R 1.5
R 1.75
R2
R 2.5
R3
18
20
8
12
16
20
8
12
16
20
6
8
10
12
14
16
18
20
22
25
30
35
10
15
20
25
30
35
8
10
12
14
16
20
25
30
35
40
16
20
25
30
35
40
10
12
14
16
20
25
30
35
40
45
50
20
25
30
35
30
40
50
13000
12000
40000
35000
13000
10000
40000
36000
25000
10000
40000
40000
40000
40000
40000
32000
24000
10000
10000
10000
10000
10000
36000
36000
26000
10000
8000
8000
32000
32000
32000
32000
32000
27000
21000
9000
6000
6000
28000
26000
23000
13000
9000
8500
24000
24000
24000
24000
24000
24000
20000
12000
11000
10000
8000
19000
19000
19000
16000
16000
16000
16000
1100
900
5000
3800
1200
750
5000
3800
2500
1000
6000
5000
5000
5000
5000
3500
2400
1000
1000
1000
800
500
5000
4600
3000
1100
800
500
6400
5100
5100
4500
4500
3800
2700
1000
700
600
4200
3800
3300
1900
1200
1100
4800
4800
3800
3800
3800
3800
3000
1700
1500
1300
1000
3400
3400
3200
2700
3500
3000
2700
43.3
35.4
196.9
149.6
47.2
29.5
196.9
149.6
98.4
39.4
236.2
196.9
196.9
196.9
196.9
137.8
94.5
39.4
39.4
39.4
31.5
19.7
196.9
181.1
118.1
43.3
31.5
19.7
252.0
200.8
200.8
177.2
177.2
149.6
106.3
39.4
27.6
23.6
165.4
149.6
129.9
74.8
47.2
43.3
189.0
189.0
149.6
149.6
149.6
149.6
118.1
66.9
59.1
51.2
39.4
133.9
133.9
126.0
106.3
137.8
118.1
106.3

Table feed
ap
-1
Depth of cut
ap
(mm)
0.02
0.02
0.08
0.05
0.04
0.02
0.09
0.06
0.04
0.03
0.1
0.1
0.08
0.08
0.06
0.05
0.04
0.04
0.04
0.04
0.02
0.02
0.12
0.08
0.07
0.06
0.05
0.03
0.15
0.15
0.13
0.13
0.1
0.1
0.08
0.08
0.06
0.04
0.13
0.13
0.12
0.09
0.08
0.07
0.2
0.2
0.15
0.15
0.15
0.15
0.1
0.1
0.1
0.08
0.05
0.2
0.2
0.15
0.1
0.2
0.15
0.15
0.02
0.01
0.07
0.03
0.02
0.01
0.08
0.04
0.025
0.02
0.1
0.1
0.07
0.05
0.05
0.03
0.03
0.03
0.02
0.02
0.015
0.01
0.11
0.075
0.05
0.04
0.03
0.03
0.15
0.15
0.13
0.1
0.1
0.06
0.06
0.05
0.04
0.03
0.13
0.11
0.08
0.07
0.06
0.04
0.2
0.2
0.15
0.15
0.15
0.1
0.08
0.08
0.06
0.05
0.04
0.2
0.2
0.15
0.1
0.2
0.15
0.15
10000
9000
26000
20000
12000
8000
25000
18000
14000
8000
24000
24000
24000
24000
21000
16000
13000
10000
10000
8000
8000
8000
20000
18000
13000
8000
7000
5000
16000
16000
16000
16000
16000
14000
11000
7000
6000
5000
14000
13000
11000
9000
6000
5500
12000
12000
12000
12000
12000
10000
10000
8000
5000
5000
4000
10000
10000
8000
8000
8000
8000
6000
800
700
3200
2100
1100
600
3100
1900
1300
800
3400
3000
3000
2600
2300
1700
1300
1000
1000
800
800
400
2600
2000
1400
800
700
400
3000
2200
2200
2200
1800
1600
1200
700
600
400
1600
1600
1200
1000
600
500
2200
2200
1500
1500
1500
1100
1100
900
500
500
400
1400
1400
1000
900
1000
800
500
31.5
27.6
126.0
82.7
43.3
23.6
122.0
74.8
51.2
31.5
133.9
118.1
118.1
102.4
90.6
66.9
51.2
39.4
39.4
31.5
31.5
15.7
102.4
78.7
55.1
31.5
27.6
15.7
118.1
86.6
86.6
86.6
70.9
63.0
47.2
27.6
23.6
15.7
63.0
63.0
47.2
39.4
23.6
19.7
86.6
86.6
59.1
59.1
59.1
43.3
43.3
35.4
19.7
19.7
15.7
55.1
55.1
39.4
35.4
39.4
31.5
19.7
SOLID END MILLS
VF2XLBS
VF2XLB
Ball nose, Long neck, 2 ute, Short shank Ball nose, Long neck, 2 ute, For hardened materials
Depth of cut
R:Radius
VF2XLBS
I159
VF2XLB
I160
I251
CUTTING CONDITIONS
VF3XB
Work
material
R
(mm)
Taper angle Neck

length
one side
(mm)
0.4
R0.4
0.9
0.4
R0.5
SOLID END MILLS
0.9
1.5
0.4
R0.75
0.9
1.5
6
8
12
8
12
16
8
10
12
16
20
25
30
35
8
12
16
20
25
30
35
40
50
60
70
12
16
20
25
30
35
10
15
20
30
15
20
30
40
15
20
30


Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
Table feed
Table feed
Table feed
Table feed
Revolution
Depth of cut
(min-1) (mm/min) (IPM) (mm) (min-1) (mm/min) (IPM) (mm) (min-1) (mm/min) (IPM) (mm) (min-1) (mm/min) (IPM) (mm)
34000
31000
28000
31000
28000
25000
27000
24000
24000
22000
20000
18000
15000
14000
27000
24000
22000
20000
18000
15000
14000
11000
8400
7000
7000
24000
22000
20000
18000
15000
14000
18000
17000
17000
14000
17000
17000
14000
13000
17000
17000
14000
2700
2100
2000
2200
2100
1100
2700
2200
2200
2100
1400
1300
960
800
2900
2400
2200
1600
1400
1100
960
800
610
510
480
2600
2400
1800
1600
1300
1100
2700
2200
2100
1600
2400
2200
1800
1300
2600
2400
2000
106.3
82.7
78.7
86.6
82.7
43.3
106.3
86.6
86.6
82.7
55.1
51.2
37.8
31.5
114.2
94.5
86.6
63.0
55.1
43.3
37.8
31.5
24.0
20.1
18.9
102.4
94.5
70.9
63.0
51.2
43.3
106.3
86.6
82.7
63.0
94.5
86.6
70.9
51.2
102.4
94.5
78.7
0.03
0.02
0.015
0.02
0.015
0.01
0.04
0.03
0.03
0.03
0.015
0.015
0.01
0.008
0.04
0.03
0.03
0.015
0.015
0.01
0.008
0.007
0.006
0.004
0.003
0.03
0.03
0.015
0.015
0.01
0.008
0.06
0.04
0.03
0.015
0.04
0.03
0.015
0.01
0.04
0.03
0.015
31000
29000
26000
29000
26000
23000
25000
22000
22000
21000
18000
17000
14000
13000
25000
22000
21000
18000
17000
14000
13000
11000
7800
6500
6500
22000
21000
18000
17000
14000
13000
17000
16000
16000
13000
16000
16000
13000
12000
16000
16000
13000
2200
1700
1600
1800
1700
910
2200
1800
1800
1700
1200
1000
780
650
2300
2000
1800
1300
1200
910
780
650
490
400
390
2100
2000
1400
1300
1000
910
2200
1800
1700
1300
2000
1800
1400
1000
2100
2000
1600
86.6
66.9
63.0
70.9
66.9
35.8
86.6
70.9
70.9
66.9
47.2
39.4
30.7
25.6
90.6
78.7
70.9
51.2
47.2
35.8
30.7
25.6
19.3
15.7
15.4
82.7
78.7
55.1
51.2
39.4
35.8
86.6
70.9
66.9
51.2
78.7
70.9
55.1
39.4
82.7
78.7
63.0
0.025
0.02
0.01
0.02
0.01
0.01
0.04
0.025
0.025
0.025
0.01
0.01
0.01
0.007
0.04
0.025
0.025
0.01
0.01
0.009
0.007
0.006
0.005
0.004
0.002
0.025
0.025
0.01
0.01
0.01
0.007
0.05
0.04
0.025
0.01
0.04
0.025
0.01
0.01
0.04
0.025
0.01
24000
22000
20000
22000
20000
18000
19000
17000
17000
16000
14000
13000
11000
10000
19000
17000
16000
14000
13000
11000
10000
8000
6000
5000
5000
17000
16000
14000
13000
11000
10000
13000
12000
12000
10000
12000
12000
10000
9000
12000
12000
10000
1700
1300
1200
1400
1300
700
1700
1400
1400
1300
900
800
600
500
1800
1500
1400
1000
900
700
600
500
380
320
300
1600
1500
1100
1000
800
700
1700
1400
1300
1000
1500
1400
1100
800
1600
1500
1200
66.9
51.2
47.2
55.1
51.2
27.6
66.9
55.1
55.1
51.2
35.4
31.5
23.6
19.7
70.9
59.1
55.1
39.4
35.4
27.6
23.6
19.7
15.0
12.6
11.8
63.0
59.1
43.3
39.4
31.5
27.6
66.9
55.1
51.2
39.4
59.1
55.1
43.3
31.5
63.0
59.1
47.2
0.02
0.015
0.01
0.015
0.01
0.008
0.03
0.02
0.02
0.02
0.01
0.009
0.008
0.006
0.03
0.02
0.02
0.01
0.009
0.008
0.006
0.005
0.004
0.003
0.002
0.02
0.02
0.01
0.009
0.008
0.006
0.04
0.03
0.02
0.01
0.03
0.02
0.01
0.008
0.03
0.02
0.01
19000
18000
16000
18000
16000
14000
15000
14000
14000
13000
11000
10000
8800
8000
15000
14000
13000
11000
10000
8800
8000
6400
4800
4000
4000
14000
13000
11000
11000
8800
8000
10000
9600
9600
8000
9600
9600
8000
7200
9600
9600
8000
1400
1000
960
1100
1000
560
1400
1100
1100
1000
720
640
480
400
1400
1200
1100
800
720
560
480
400
300
260
240
1300
1200
880
800
640
560
1400
1100
1000
800
1200
1100
880
640
1300
1200
960
55.1
39.4
37.8
43.3
39.4
22.0
55.1
43.3
43.3
39.4
28.3
25.2
18.9
15.7
55.1
47.2
43.3
31.5
28.3
22.0
18.9
15.7
11.8
10.2
9.4
51.2
47.2
34.6
31.5
25.2
22.0
55.1
43.3
39.4
31.5
47.2
43.3
34.6
25.2
51.2
47.2
37.8
0.015
0.01
0.007
0.01
0.007
0.006
0.02
0.015
0.015
0.015
0.007
0.006
0.006
0.004
0.02
0.015
0.015
0.007
0.006
0.006
0.004
0.003
0.003
0.002
0.001
0.015
0.015
0.007
0.006
0.006
0.004
0.03
0.02
0.015
0.007
0.02
0.015
0.007
0.006
0.02
0.015
0.007
2) If the rigidity of the machine or the workpiece installation is very low, or chattering is generated, please reduce the revolution and the
feed rate proportionately.
I252
VF3XB
I165
R
(mm)
Taper angle Neck

length
one side
(mm)
0.4
R1
0.9
1.5
0.9
R1.25
1.5
0.4
R1.5
0.9
1.5
R2
0.9
R2.5
0.9
16
20
25
30
35
40
20
25
30
35
40
50
60
70
25
30
35
40
20
30
40
20
30
40
20
30
40
50
20
30
40
50
60
70
50
60
70
30
40
50
60
35
40
60


Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
Table feed
Table feed
Table feed
Table feed
Revolution
Depth of cut
(min-1) (mm/min) (IPM) (mm) (min-1) (mm/min) (IPM) (mm) (min-1) (mm/min) (IPM) (mm) (min-1) (mm/min) (IPM) (mm)
15000
14000
14000
13000
13000
12000
14000
14000
13000
13000
12000
11000
9800
8400
14000
12600
13000
12000
13000
12000
11000
13000
12000
11000
12000
11000
11000
11000
12000
11000
11000
11000
9800
9800
11000
9800
9800
10000
9500
9500
9000
8000
8000
7600
3200
2400
2100
1800
1600
1400
2600
2200
1900
1800
1600
1400
1100
960
2400
2100
1900
1800
2900
2600
2200
3000
2700
2400
3700
2900
2400
2000
3800
3000
2600
2100
2000
1800
2200
2100
2000
3200
2400
2100
1900
3500
3200
2400
126.0
94.5
82.7
70.9
63.0
55.1
102.4
86.6
74.8
70.9
63.0
55.1
43.3
37.8
94.5
82.7
74.8
70.9
114.2
102.4
86.6
118.1
106.3
94.5
145.7
114.2
94.5
78.7
149.6
118.1
102.4
82.7
78.7
70.9
86.6
82.7
78.7
126.0
94.5
82.7
74.8
137.8
126.0
94.5
0.07
0.06
0.04
0.03
0.03
0.015
0.06
0.05
0.04
0.04
0.03
0.015
0.007
0.004
0.05
0.04
0.04
0.03
0.06
0.05
0.04
0.06
0.05
0.04
0.13
0.07
0.06
0.04
0.13
0.07
0.06
0.04
0.03
0.015
0.04
0.03
0.015
0.3
0.15
0.1
0.07
0.3
0.2
0.15
14000
13000
13000
12000
12000
11000
13000
13000
12000
12000
11000
10000
9100
7800
13000
12000
12000
11000
12000
11000
9800
12000
11050
9800
11000
10000
10000
9800
11000
10000
10000
9800
9100
9100
9800
9100
9100
9400
8800
8800
8300
7400
7400
7000
2600
2000
1700
1400
1300
1200
2100
1800
1600
1400
1300
1200
910
780
2000
1700
1600
1400
2300
2100
1800
2500
2200
2000
3000
2300
2000
1600
3100
2500
2100
1700
1600
1400
1800
1700
1600
2600
2000
1700
1600
2900
2600
2000
102.4
78.7
66.9
55.1
51.2
47.2
82.7
70.9
63.0
55.1
51.2
47.2
35.8
30.7
78.7
66.9
63.0
55.1
90.6
82.7
70.9
98.4
86.6
78.7
118.1
90.6
78.7
63.0
122.0
98.4
82.7
66.9
63.0
55.1
70.9
66.9
63.0
102.4
78.7
66.9
63.0
114.2
102.4
78.7
0.06
0.05
0.04
0.03
0.025
0.01
0.05
0.04
0.04
0.03
0.025
0.01
0.006
0.004
0.04
0.04
0.03
0.025
0.05
0.04
0.04
0.05
0.04
0.04
0.1
0.06
0.05
0.04
0.1
0.06
0.05
0.04
0.025
0.01
0.04
0.025
0.01
0.25
0.12
0.1
0.06
0.25
0.18
0.12
11000
10000
10000
9000
9000
8500
10000
10000
9000
9000
8500
8000
7000
6000
10000
9000
9000
8500
9000
8500
7500
9000
8500
7500
8500
8000
8000
7500
8500
8000
8000
7500
7000
7000
7500
7000
7000
7200
6800
6800
6400
5700
5700
5400
2000
1500
1300
1100
1000
900
1600
1400
1200
1100
1000
900
700
600
1500
1300
1200
1100
1800
1600
1400
1900
1700
1500
2300
1800
1500
1200
2400
1900
1600
1300
1200
1100
1400
1300
1200
2000
1500
1300
1200
2200
2000
1500
78.7
59.1
51.2
43.3
39.4
35.4
63.0
55.1
47.2
43.3
39.4
35.4
27.6
23.6
59.1
51.2
47.2
43.3
70.9
63.0
55.1
74.8
66.9
59.1
90.6
70.9
59.1
47.2
94.5
74.8
63.0
51.2
47.2
43.3
55.1
51.2
47.2
78.7
59.1
51.2
47.2
86.6
78.7
59.1
0.05
0.04
0.03
0.025
0.02
0.01
0.04
0.03
0.03
0.025
0.02
0.01
0.005
0.003
0.03
0.03
0.025
0.02
0.04
0.03
0.03
0.04
0.03
0.03
0.09
0.05
0.04
0.03
0.09
0.05
0.04
0.03
0.02
0.01
0.03
0.02
0.01
0.2
0.1
0.08
0.05
0.2
0.15
0.1
8800
8000
8000
7200
7200
6800
8000
8000
7200
7200
6800
6400
5600
4800
8000
7200
7200
6800
7200
6800
6000
7200
6800
6000
6800
6400
6400
6000
6800
6400
6400
6000
5600
5600
6000
5600
5600
5800
5400
5400
5100
4600
4600
4300
1600
1200
1000
880
800
720
1300
1100
960
880
800
720
560
480
1200
1000
960
880
1400
1300
1100
1500
1400
1200
1800
1400
1200
960
1900
1500
1300
1000
960
880
1100
1000
960
1600
1200
1000
960
1800
1600
1200
63.0
47.2
39.4
34.6
31.5
28.3
51.2
43.3
37.8
34.6
31.5
28.3
22.0
18.9
47.2
39.4
37.8
34.6
55.1
51.2
43.3
59.1
55.1
47.2
70.9
55.1
47.2
37.8
74.8
59.1
51.2
39.4
37.8
34.6
43.3
39.4
37.8
63.0
47.2
39.4
37.8
70.9
63.0
47.2
0.03
0.03
0.02
0.02
0.015
0.007
0.03
0.025
0.02
0.02
0.015
0.007
0.003
0.002
0.025
0.02
0.02
0.015
0.03
0.025
0.02
0.03
0.025
0.02
0.06
0.03
0.03
0.02
0.06
0.03
0.03
0.02
0.015
0.007
0.02
0.015
0.007
0.15
0.07
0.06
0.03
0.15
0.1
0.07
SOLID END MILLS
Work
material
2) If the rigidity of the machine or the workpiece installation is very low, or chattering is generated, please reduce the revolution and the
feed rate proportionately.
VF3XB
I165
I253
CUTTING CONDITIONS
VF4MB
Work
material
R
(mm)
R0.5
R1
R1.5
R2
R2.5
R3
R4
R5
R6
AISI H13 etc.
AISI D2 etc.
% 15
% >15
Table feed
Revolution
(min-1) (mm/min)
(IPM)
40000
40000
40000
32000
25000
21000
16000
13000
9000
8000
9600
12000
11000
9000
8400
6400
5200
3600
315.0
378.0
472.4
433.1
354.3
330.7
252.0
204.7
141.7
Table feed
Revolution
(min-1) (mm/min)
(IPM)
40000
40000
32000
24000
19000
15000
12000
9600
7200
3800
5600
5600
4700
3800
3400
2600
2200
1700
149.6
220.5
220.5
185.0
149.6
133.9
102.4
86.6
66.9
% 15
Depth of
cut
Table feed
Revolution
(mm)
(min-1) (mm/min)
(IPM)
0.06
0.11
0.13
0.15
0.20
0.25
0.30
0.50
0.50
Depth of
cut
40000
40000
32000
24000
19000
16000
12000
10000
7000
5600
8000
7700
6200
5300
4800
3600
3200
2200
<Please
220.5
315.0
303.1
244.1
208.7
189.0
141.7
126.0
86.6
% >15
Table feed
Revolution
(min-1) (mm/min)
(IPM)
40000
28000
19000
14000
12000
9600
7200
5800
4300
3100
3100
2900
2500
2200
2000
1600
1300
940
122.0
122.0
114.2
98.4
86.6
78.7
63.0
51.2
37.0
Depth of
cut
(mm)
0.05
0.10
0.12
0.13
0.15
0.20
0.20
0.20
0.30
R:Radius
SOLID END MILLS
Work
material
R
(mm)
R0.5
R1
R1.5
R2
R2.5
R3
R4
R5
R6
Depth of
cut
I254

% 15
% >15
Table feed
Revolution
(min-1) (mm/min)
(IPM)
40000
24000
16000
12000
9600
8000
6000
4800
3600
4700
5000
4200
3100
2700
2300
1900
1500
1100
185.0
196.9
165.4
122.0
106.3
90.6
74.8
59.1
43.3
Table feed
Revolution
(min-1) (mm/min)
(IPM)
32000
16000
11000
8000
6000
5000
4000
3000
2200
1700
1200
1100
1000
780
780
620
550
400
66.9
47.2
43.3
39.4
30.7
30.7
24.4
21.7
15.7
Depth of
cut
(mm)
0.03
0.06
0.07
0.08
0.08
0.09
0.09
0.10
0.10

increased.
<Please
refer to the list

above for depth of cut.
R:Radius
VF4MB
I168
VF4SVB
Ball nose, Short cut length, 4 ute, Variable curve
Work
material
R
(mm)
R 3
R 4
R 5
R 6
R 8
R10

Pre-hardened steel

Titanium alloy

AISI P21 etc.
AISI 304, AISI 306, Ti 6Al 4V etc.

% >15
% 15
Table feed
Revolution
(min-1) (mm/min)
(IPM)
16000
12000
9600
8000
6000
4800
4800
4300
4100
4000
3200
3000
189.0
169.3
161.4
157.5
126.0
118.1
Table feed
Revolution
(min-1) (mm/min)
(IPM)
10600
8000
6400
5300
4000
3200
2100
1900
1800
1800
1400
1300
82.7
74.8
70.9
70.9
55.1
51.2
Depth of
% 15
cut
Table feed
Revolution
ap
(min-1) (mm/min)
(mm)
(IPM)
0.5
0.8
1
1.2
1.6
2
12000
9000
7200
6000
4500
3600
3200
3200
3000
3000
2500
2300
126.0
126.0
118.1
118.1
98.4
90.6
% >15
Table feed
Revolution
(min-1) (mm/min)
(IPM)
8000
6000
4800
4000
3000
2400
1400
1400
1300
1300
1100
1000
55.1
55.1
51.2
51.2
43.3
39.4
Depth of
cut
ap
(mm)
0.5
0.8
1
1.2
1.6
2
0.5R
Depth of
cut
ap
R:Radius
R
(mm)
R 3
R 4
R 5
R 6
R 8
R10
Inconel718 etc.
% 15
% >15
Table feed
Revolution
(min-1) (mm/min)
(IPM)
3200
2400
2000
1700
1200
1000
500
430
420
350
300
250
19.7
16.9
16.5
13.8
11.8
9.8
Table feed
Revolution
(min-1) (mm/min)
(IPM)
2100
1600
1300
1100
800
640
210
190
180
150
130
100
8.3
7.5
7.1
5.9
5.1
3.9
Depth of
cut
ap
(mm)
0.25
0.4
0.5
0.6
0.8
1

2) When cutting austenitic stainless steels, the use of watersoluble cutting uid is especially effective.
increased.
4) The irregular helix ute end mill has a larger effect on controlling
vibration when compared to standard end mills. However, if the
rigidity of the machine or the workpiece installation is very
low, then vibration can occur. In this case, please reduce the
revolution and feed rate proportionately, or set a lower depth
of cut.
SOLID END MILLS

Work
material
0.2R
Depth of
cut
ap
R:Radius
VF4SVB
I169
I255
CUTTING CONDITIONS
VFHVRB
yHigh feed conditions

Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
Work material
SOLID END MILLS
Dia.
R Neck length Revolution Table feed Depth of cut Depth of cut Revolution Table feed Depth of cut Depth of cut Revolution Table feed Depth of cut Depth of cut Revolution Table feed Depth of cut Depth of cut
(mm) (mm) (mm) (min-1) (mm/min) (IPM) ap (mm) ae (mm) (min-1) (mm/min) (IPM) ap (mm) ae (mm) (min-1) (mm/min) (IPM) ap (mm) ae (mm) (min-1) (mm/min) (IPM) ap (mm) ae (mm)
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
0.8
0.8
0.5
0.5
0.5
0.5
1
1
1
0.5
0.5
1
1
1
1.5
1.5
1.5
1.5
2
2
4
6
8
10
15
20
4
6
10
15
20
25
30
6
10
15
20
25
30
35
40
10
15
20
30
10
15
20
30
40
50
12
20
30
48
12
20
30
18
30
18
30
54
18
30
42
54
18
30
40000 7200 283.5 0.04

40000 6500 255.9 0.03
32000 4500 177.2 0.022
24000 2700 106.3 0.015
16000 1200 47.2 0.008
14000 1000 39.4 0.005
32000 10000 393.7 0.1
32000 7800 307.1 0.08
27000 5700 224.4 0.05
22000 3200 126.0 0.03
16000 1400 55.1 0.02
13000 1000 39.4 0.015
13000 900 35.4 0.01
24000 10000 393.7 0.1
24000 10000 393.7 0.08
20000 7000 275.6 0.05
20000 3600 141.7 0.04
16000 1800 70.9 0.03
16000 1400 55.1 0.025
13000 1100 43.3 0.02
13000 1000 39.4 0.02
16000 11000 433.1 0.12
16000 9000 354.3 0.11
13000 7200 283.5 0.09
13000 5700 224.4 0.06
16000 11000 433.1 0.24
16000 9000 354.3 0.22
13000 7200 283.5 0.19
13000 5700 224.4 0.12
11000 3600 141.7 0.08
8000 2600 102.4 0.07
8400 6000 236.2 0.15
8400 6000 236.2 0.14
6900 4900 192.9 0.12
5600 2000 78.7 0.07
12000 12000 472.4 0.3
12000 12000 472.4 0.27
10000 9900 389.8 0.24
4000 3900 153.5 0.15
4000 3900 153.5 0.14
8000 13000 511.8 0.5
8000 13000 511.8 0.45
6600 11000 433.1 0.25
8000 13000 511.8 0.5
8000 13000 511.8 0.45
6600 11000 433.1 0.4
6600 11000 433.1 0.25
8000 13000 511.8 0.5
8000 13000 511.8 0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1.5
1.5
1.5
1.5
1
1
1
1
1
1
2
2
2
2
1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
33000 5100 200.8 0.03

33000 4600 181.1 0.022
27000 3200 126.0 0.018
20000 1900 74.8 0.01
14000 700 27.6 0.005
12000 600 23.6 0.004
27000 7100 279.5 0.08
27000 5500 216.5 0.06
22000 4000 157.5 0.035
18000 2300 90.6 0.025
14000 1200 47.2 0.016
11000 800 31.5 0.012
11000 700 27.6 0.008
20000 7100 279.5 0.08
20000 7100 279.5 0.06
17000 5000 196.9 0.04
17000 2600 102.4 0.03
14000 1400 55.1 0.025
14000 1200 47.2 0.02
11000 800 31.5 0.018
11000 700 27.6 0.015
13000 7800 307.1 0.09
13000 6400 252.0 0.08
11000 5100 200.8 0.07
11000 4000 157.5 0.05
13000 7800 307.1 0.19
13000 6400 252.0 0.17
11000 5100 200.8 0.15
11000 4000 157.5 0.09
9100 2600 102.4 0.06
6600 1800 70.9 0.05
7000 4300 169.3 0.12
7000 4300 169.3 0.11
5700 3500 137.8 0.09
4600 1400 55.1 0.05
10000 8500 334.6 0.23
10000 8500 334.6 0.21
8300 7000 275.6 0.19
3300 2800 110.2 0.12
3300 2800 110.2 0.11
6600 9200 362.2 0.4
6600 9200 362.2 0.35
5500 7800 307.1 0.2
6600 9200 362.2 0.4
6600 9200 362.2 0.35
5500 7800 307.1 0.3
5500 7800 307.1 0.2
6600 9200 362.2 0.4
6600 9200 362.2 0.35
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1.5
1.5
1.5
1.5
1
1
1
1
1
1
2
2
2
2
1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
27000 4100 161.4 0.025

27000 3700 145.7 0.018
21000 2600 102.4 0.012
16000 1500 59.1 0.008
12000 500 19.7 0.003
10000 400 15.7 0.002
21000 5700 224.4 0.06
21000 4200 165.4 0.05
18000 3000 118.1 0.03
15000 1700 66.9 0.018
13000 1000 39.4 0.012
10000 700 27.6 0.009
10000 600 23.6 0.006
16000 5700 224.4 0.06
16000 5700 224.4 0.05
13000 3200 126.0 0.03
13000 1800 70.9 0.025
12000 1100 43.3 0.02
12000 900 35.4 0.016
10000 700 27.6 0.014
10000 600 23.6 0.012
11000 6300 248.0 0.07
11000 5100 200.8 0.06
8700 4000 157.5 0.05
8700 3000 118.1 0.04
11000 6300 248.0 0.14
11000 5100 200.8 0.13
8700 4000 157.5 0.11
8700 3000 118.1 0.07
7400 2000 78.7 0.05
5800 1500 59.1 0.04
5600 3400 133.9 0.09
5600 3400 133.9 0.08
4600 2800 110.2 0.07
3800 1100 43.3 0.04
8000 6800 267.7 0.18
8000 6800 267.7 0.16
6700 5600 220.5 0.14
2700 2200 86.6 0.09
2700 2200 86.6 0.08
5400 7400 291.3 0.3
5400 7400 291.3 0.27
4400 6300 248.0 0.15
5400 7400 291.3 0.3
5400 7400 291.3 0.27
4400 6300 248.0 0.24
4400 6300 248.0 0.15
5400 7400 291.3 0.3
5400 7400 291.3 0.27
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1.5
1.5
1.5
1.5
1
1
1
1
1
1
2
2
2
2
1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
20000 1800 70.9 0.013

20000 1600 63.0 0.01
16000 1100 43.3 0.008
12000 700 27.6 0.006
10000 400 15.7 0.003
9000 300 11.8 0.002
16000 2500 98.4 0.03
16000 2000 78.7 0.025
14000 1400 55.1 0.014
11000 1000 39.4 0.009
9000 700 27.6 0.007
7500 500 19.7 0.005
7500 400 15.7 0.004
12000 2500 98.4 0.03
12000 2500 98.4 0.025
10000 1800 70.9 0.016
10000 900 35.4 0.012
9000 720 28.3 0.01
9000 650 25.6 0.008
7000 500 19.7 0.007
7000 400 15.7 0.006
8000 2800 110.2 0.04
8000 2300 90.6 0.04
6500 1800 70.9 0.03
6500 1400 55.1 0.02
8000 2800 110.2 0.07
8000 2300 90.6 0.07
6500 1800 70.9 0.06
6500 1400 55.1 0.04
5500 1000 39.4 0.025
4600 800 31.5 0.02
4200 1500 59.1 0.05
4200 1500 59.1 0.04
3500 1200 47.2 0.03
2800 500 19.7 0.02
6000 3000 118.1 0.1
6000 3000 118.1 0.08
5000 2500 98.4 0.07
2000 1000 39.4 0.05
2000 1000 39.4 0.04
4000 3300 129.9 0.15
4000 3300 129.9 0.14
3300 2800 110.2 0.08
4000 3300 129.9 0.15
4000 3300 129.9 0.14
3300 2800 110.2 0.12
3300 2800 110.2 0.08
4000 3300 129.9 0.15
4000 3300 129.9 0.14
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1.5
1.5
1.5
1.5
1
1
1
1
1
1
2
2
2
2
1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
Depth of cut
I256
VFHVRB
I170


Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
Work material
7
8
8
8
8
8
8
8
8
9
10
10
10
10
10
10
10
10
11
12
12
12
12
12
12
12
12
12
12
13
16
16
16
16
16
1.5 6800 13000 511.8 0.5

3
0.5 24 3000 3900 153.5 0.18 5
0.5 40 3000 3900 153.5 0.16 5
4.5
1
24 4200 6500 255.9 0.3
1
40 4200 6500 255.9 0.27 4.5
2
24 6000 13000 511.8 0.6
3
2
40 6000 13000 511.8 0.54 3
2
56 5000 11000 433.1 0.48 3
3
2
72 5000 11000 433.1 0.3
5300 13000 511.8 0.6
2
3.5
0.5 30 2400 3900 153.5 0.18 6.5
0.5 50 2400 3900 153.5 0.16 6.5
6
1
30 3300 6500 255.9 0.3
1
50 3300 6500 255.9 0.27 6
4.5
2
30 4800 13000 511.8 0.6
2
50 4800 13000 511.8 0.54 4.5
2
70 4000 11000 433.1 0.48 4.5
2
90 4000 11000 433.1 0.48 4.5
4300 12000 472.4 0.6
2
5
0.5 36 2000 3600 141.7 0.27 8
0.5 60 2000 3600 141.7 0.24 8
1
36 2400 4800 189.0 0.36 7.5
1
60 2400 4800 189.0 0.32 7.5
6
2
36 4000 12000 472.4 0.9
2
60 4000 12000 472.4 0.8
6
6
2
84 3300 9900 389.8 0.7
2
108 3300 9900 389.8 0.45 6
4.5
3
36 4000 12000 472.4 0.9
4.5
3
60 4000 12000 472.4 0.8
3700 12000 472.4 0.9
3
5
0.5 42 1500 3000 118.1 0.27 11
2
42 2100 5000 196.9 0.45 9
7.5
3
42 3000 10000 393.7 0.9
7.5
3
80 3000 10000 393.7 0.8
7.5
3
120 2500 8300 326.8 0.7
5600
2500
2500
3500
3500
5000
5000
4200
4200
4400
2000
2000
2700
2700
4000
4000
3300
3300
3600
1700
1700
2000
2000
3300
3300
2700
2700
3300
3300
3100
1200
1700
2500
2500
2100
9200 362.2
2800 110.2
2800 110.2
4600 181.1
4600 181.1
9200 362.2
9200 362.2
7800 307.1
7800 307.1
9200 362.2
2800 110.2
2800 110.2
4600 181.1
4600 181.1
9200 362.2
9200 362.2
7800 307.1
7800 307.1
8500 334.6
2600 102.4
2600 102.4
3400 133.9
3400 133.9
8500 334.6
8500 334.6
7000 275.6
7000 275.6
8500 334.6
8500 334.6
8500 334.6
2100 82.7
3600 141.7
7100 279.5
7100 279.5
5900 232.3
0.4
3
0.14 5
0.12 5
0.23 4.5
0.21 4.5
0.46 3
0.42 3
0.37 3
0.23 3
0.46 3.5
0.14 6.5
0.12 6.5
0.23 6
0.21 6
0.46 4.5
0.42 4.5
0.37 4.5
0.37 4.5
0.46 5
0.21 8
0.18 8
0.28 7.5
0.25 7.5
0.7
6
0.6
6
0.55 6
0.35 6
0.7
4.5
0.6
4.5
0.7
5
0.21 11
0.35 9
0.7
7.5
0.6
7.5
0.55 7.5
4600
2000
2000
2800
2800
4000
4000
3400
3400
3600
1600
1600
2200
2200
3200
3200
2700
2700
2900
1300
1300
1600
1600
2700
2700
2200
2200
2700
2700
2500
1000
1400
2000
2000
1700
7400 291.3
2200 86.6
2200 86.6
3700 145.7
3700 145.7
7400 291.3
7400 291.3
6300 248.0
6300 248.0
7400 291.3
2200 86.6
2200 86.6
3700 145.7
3700 145.7
7400 291.3
7400 291.3
6300 248.0
6300 248.0
6800 267.7
2100 82.7
2100 82.7
2700 106.3
2700 106.3
6800 267.7
6800 267.7
5600 220.5
5600 220.5
6800 267.7
6800 267.7
6800 267.7
1700 66.9
2900 114.2
5700 224.4
5700 224.4
4700 185.0
0.3
3
0.11 5
0.1
5
0.18 4.5
0.16 4.5
0.36 3
0.32 3
0.3
3
0.2
3
0.36 3.5
0.11 6.5
0.1
6.5
0.18 6
0.16 6
0.36 4.5
0.32 4.5
0.3
4.5
0.3
4.5
0.36 5
0.14 8
0.12 8
0.18 7.5
0.16 7.5
0.45 6
0.4
6
0.36 6
0.23 6
0.45 4.5
0.4
4.5
0.45 5
0.12 11
0.2
9
0.4
7.5
0.37 7.5
0.32 7.5
3400
1500
1500
2100
2100
3000
3000
2500
2500
2700
1200
1200
1700
1700
2400
2400
2000
2000
2200
1000
1000
1200
1200
2000
2000
1700
1700
2000
2000
1900
750
1100
1500
1500
1300
3300 129.9
1000 39.4
1000 39.4
1600 63.0
1600 63.0
3300 129.9
3300 129.9
2800 110.2
2800 110.2
3300 129.9
1000 39.4
1000 39.4
1600 63.0
1600 63.0
3300 129.9
3300 129.9
2800 110.2
2800 110.2
3000 118.1
900 35.4
900 35.4
1200 47.2
1200 47.2
3000 118.1
3000 118.1
2500 98.4
2500 98.4
3000 118.1
3000 118.1
3000 118.1
750 29.5
1300 51.2
2500 98.4
2500 98.4
2100 82.7
0.15 3
0.05 5
0.05 5
0.09 4.5
0.08 4.5
0.18 3
0.16 3
0.14 3
0.09 3
0.18 3.5
0.05 6.5
0.05 6.5
0.09 6
0.08 6
0.18 4.5
0.16 4.5
0.14 4.5
0.14 4.5
0.18 5
0.07 8
0.06 8
0.09 7.5
0.08 7.5
0.23 6
0.2
6
0.18 6
0.11 6
0.23 4.5
0.2
4.5
0.23 5
0.05 11
0.08 9
0.15 7.5
0.14 7.5
0.12 7.5
SOLID END MILLS
Dia.
Depth of cut
VFHVRB
I170
I257
CUTTING CONDITIONS
VFHVRB
yHigh depth of cut conditions

Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
Work material
SOLID END MILLS
Dia.
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
0.8
0.8
0.5
0.5
0.5
0.5
1
1
1
0.5
0.5
1
1
1
1.5
1.5
1.5
1.5
2
2
4
6
8
10
15
20
4
6
10
15
20
25
30
6
10
15
20
25
30
35
40
10
15
20
30
10
15
20
30
40
50
12
20
30
48
12
20
30
18
30
18
30
54
18
30
42
54
18
30
24000
24000
19000
14000

19000
19000
16000
13000

14000
14000
12000
12000

9600
9600
7800
7800
9600
9600
7800
7800

5000
5000
4100

7200
7200
6000
2400
2400
4800
4800
4000
4800
4800
4000
4000
4800
4800
2200
2000
1400
800

3000
2300
1700
1000

3000
3000
2100
1100

3300
2700
2200
1700
3300
2700
2200
1700

1800
1800
1500

3600
3600
3000
1200
1200
3900
3900
3300
3900
3900
3300
3300
3900
3900
86.6
78.7
55.1
31.5

118.1
90.6
66.9
39.4

118.1
118.1
82.7
43.3

129.9
106.3
86.6
66.9
129.9
106.3
86.6
66.9

70.9
70.9
59.1

141.7
141.7
118.1
47.2
47.2
153.5
153.5
129.9
153.5
153.5
129.9
129.9
153.5
153.5
0.08
0.07
0.05
0.04

0.2
0.16
0.1
0.06

0.2
0.16
0.1
0.08

0.24
0.22
0.18
0.12
0.5
0.5
0.4
0.24

0.3
0.3
0.24

0.6
0.6
0.5
0.3
0.3
1
0.9
0.5
1
0.9
0.8
0.5
1
0.9
0.45
0.45
0.45
0.45

0.65
0.65
0.65
0.65

0.75
0.75
0.75
0.75

1.5
1.5
1.5
1.5
1
1
1
1

2
2
2

1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
20000
20000
16000
12000

16000
16000
13000
11000

12000
12000
10000
10000

8000
8000
6500
6500
8000
8000
6500
6500

4200
4200
3400

6000
6000
5000
2000
2000
4000
4000
3300
4000
4000
3300
3300
4000
4000
1500
1400
1000
600

2100
1600
1200
700

2100
2100
1500
800

2300
1900
1500
1200
2300
1900
1500
1200

1300
1300
1100

2500
2500
2100
840
840
2700
2700
2300
2700
2700
2300
2300
2700
2700
59.1
55.1
39.4
23.6

82.7
63.0
47.2
27.6

82.7
82.7
59.1
31.5

90.6
74.8
59.1
47.2
90.6
74.8
59.1
47.2

51.2
51.2
43.3

98.4
98.4
82.7
33.1
33.1
106.3
106.3
90.6
106.3
106.3
90.6
90.6
106.3
106.3
0.07
0.05
0.04
0.03

0.16
0.13
0.07
0.05

0.16
0.13
0.08
0.06

0.2
0.17
0.14
0.1
0.4
0.35
0.3
0.2

0.24
0.22
0.19

0.5
0.4
0.4
0.24
0.22
0.8
0.7
0.4
0.8
0.7
0.6
0.4
0.8
0.7
0.45
0.45
0.45
0.45

0.65
0.65
0.65
0.65

0.75
0.75
0.75
0.75

1.5
1.5
1.5
1.5
1
1
1
1

2
2
2

1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
16000
16000
13000
9000

13000
13000
11000
9000

9400
9400
8000
8000

6400
6400
5200
5200
6400
6400
5200
5200

3400
3400
2700

4800
4800
4000
1600
1600
3200
3200
2700
3200
3200
2700
2700
3200
3200
1200
1100
800
400

1700
1300
1000
600

1700
1700
1200
600

1800
1500
1200
1000
1800
1500
1200
1000

1000
1000
840

2000
2000
1700
670
670
2200
2200
1800
2200
2200
1800
1800
2200
2200
47.2
43.3
31.5
15.7

66.9
51.2
39.4
23.6

66.9
66.9
47.2
23.6

70.9
59.1
47.2
39.4
70.9
59.1
47.2
39.4

39.4
39.4
33.1

78.7
78.7
66.9
26.4
26.4
86.6
86.6
70.9
86.6
86.6
70.9
70.9
86.6
86.6
0.05
0.04
0.03
0.025

0.12
0.1
0.05
0.04

0.12
0.1
0.06
0.05

0.14
0.13
0.11
0.07
0.3
0.25
0.23
0.14

0.18
0.17
0.14

0.36
0.32
0.3
0.18
0.17
0.6
0.5
0.3
0.6
0.5
0.5
0.3
0.6
0.5
0.45
0.45
0.45
0.45

0.65
0.65
0.65
0.65

0.75
0.75
0.75
0.75

1.5
1.5
1.5
1.5
1
1
1
1

2
2
2

1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
12000
12000
9500
7000

9500
9500
8000
6500

7000
7000
6000
6000

4800
4800
3900
3900
4800
4800
3900
3900

2500
2500
2100

3600
3600
3000
1200
1200
2400
2400
2000
2400
2400
2000
2000
2400
2400
550
500
350
200

750
580
430
250

750
750
530
280

830
680
550
430
830
680
550
430

450
450
380

900
900
750
300
300
980
980
830
980
980
830
830
980
980
21.7
19.7
13.8
7.9

29.5
22.8
16.9
9.8

29.5
29.5
20.9
11.0

32.7
26.8
21.7
16.9
32.7
26.8
21.7
16.9

17.7
17.7
15.0

35.4
35.4
29.5
11.8
11.8
38.6
38.6
32.7
38.6
38.6
32.7
32.7
38.6
38.6
0.025
0.02
0.016
0.012

0.06
0.05
0.03
0.018

0.06
0.05
0.03
0.025

0.07
0.06
0.05
0.04
0.14
0.13
0.11
0.05

0.06
0.06
0.05

0.12
0.11
0.1
0.06
0.06
0.2
0.18
0.1
0.2
0.18
0.16
0.1
0.2
0.18
0.45
0.45
0.45
0.45

0.65
0.65
0.65
0.65

0.75
0.75
0.75
0.75

1.5
1.5
1.5
1.5
1
1
1
1

2
2
2

1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
Depth of cut
I258
VFHVRB
I170


Pre-hardened steel
AISI 1050, AISI 35,

AISI P20 etc.

AISI P21 etc.
AISI H13 etc.
AISI D2 etc.
Work material
7
8
8
8
8
8
8
8
8
9
10
10
10
10
10
10
10
10
11
12
12
12
12
12
12
12
12
12
12
13
16
16
16
16
16
1.5 4100 3900 153.5 1

3
0.5 24 1800 1200 47.2 0.35 5
0.5 40 1800 1200 47.2 0.3
5
1
24 2500 2000 78.7 0.6
4.5
4.5
1
40 2500 2000 78.7 0.5
3
2
24 3600 3900 153.5 1.2
3
2
40 3600 3900 153.5 1.1
3
2
56 3000 3300 129.9 1
3
2
72 3000 3300 129.9 0.6
3200 3900 153.5 1.2
2
3.5
0.5 30 1400 1200 47.2 0.35 6.5
6.5
0.5 50 1400 1200 47.2 0.3
6
1
30 2000 2000 78.7 0.6
1
50 2000 2000 78.7 0.5
6
4.5
2
30 2900 3900 153.5 1.2
4.5
2
50 2900 3900 153.5 1.1
2
70 2400 3300 129.9 1
4.5
4.5
2
90 2400 3300 129.9 1
2600 3600 141.7 1.2
2
5
0.5 36 1200 1100 43.3 0.5
8
8
0.5 60 1200 1100 43.3 0.5
7.5
1
36 1400 1400 55.1 0.7
7.5
1
60 1400 1400 55.1 0.6
6
2
36 2400 3600 141.7 1.8
6
2
60 2400 3600 141.7 1.6
6
2
84 2000 3000 118.1 1.4
2
108 2000 3000 118.1 0.9
6
4.5
3
36 2400 3600 141.7 1.8
4.5
3
60 2400 3600 141.7 1.6
2200 3600 141.7 1.8
3
5
0.5 42 900 900 35.4 0.5 11
2
42 1300 1500 59.1 0.9
9
7.5
3
42 1800 3000 118.1 1.8
7.5
3
80 1800 3000 118.1 1.6
7.5
3
120 1500 2500 98.4 1.4
3400
1500
1500
2100
2100
3000
3000
2500
2500
2700
1200
1200
1700
1700
2400
2400
2000
2000
2200
1000
1000
1200
1200
2000
2000
1700
1700
2000
2000
1800
750
1100
1500
1500
1200
2700 106.3
840 33.1
840 33.1
1400 55.1
1400 55.1
2700 106.3
2700 106.3
2300 90.6
2300 90.6
2700 106.3
840 33.1
840 33.1
1400 55.1
1400 55.1
2700 106.3
2700 106.3
2300 90.6
2300 90.6
2500 98.4
770 30.3
770 30.3
1000 39.4
1000 39.4
2500 98.4
2500 98.4
2100 82.7
2100 82.7
2500 98.4
2500 98.4
2500 98.4
630 24.8
1100 43.3
2100 82.7
2100 82.7
1800 70.9
0.8
3
0.3
5
0.25 5
0.5
4.5
0.4
4.5
1
3
0.9
3
0.8
3
0.5
3
1
3.5
0.3
6.5
0.25 6.5
0.5
6
0.4
6
1
4.5
0.9
4.5
0.8
4.5
0.8
4.5
1
5
0.4
8
0.4
8
0.6
7.5
0.5
7.5
1.4
6
1.3
6
1.1
6
0.7
6
1.4
4.5
1.3
4.5
1.4
5
0.4 11
0.7
9
1.4
7.5
1.3
7.5
1.1
7.5
2700
1200
1200
1700
1700
2400
2400
2000
2000
2100
940
940
1300
1300
1900
1900
1600
1600
1700
800
800
940
940
1600
1600
1300
1300
1600
1600
1500
600
870
1200
1200
1000
2200
670
670
1100
1100
2200
2200
1800
1800
2200
670
670
1100
1100
2200
2200
1800
1800
2000
620
620
780
780
2000
2000
1700
1700
2000
2000
2000
500
840
1700
1700
1400
86.6
26.4
26.4
43.3
43.3
86.6
86.6
70.9
70.9
86.6
26.4
26.4
43.3
43.3
86.6
86.6
70.9
70.9
78.7
24.4
24.4
30.7
30.7
78.7
78.7
66.9
66.9
78.7
78.7
78.7
19.7
33.1
66.9
66.9
55.1
0.6 3
0.2 5
0.2 5
0.4 4.5
0.3 4.5
0.7 3
0.7 3
0.6 3
0.4 3
0.7 3.5
0.2 6.5
0.2 6.5
0.4 6
0.3 6
0.7 4.5
0.7 4.5
0.6 4.5
0.6 4.5
0.7 5
0.3 8
0.3 8
0.4 7.5
0.4 7.5
1.1 6
1
6
0.8 6
0.5 6
1.1 4.5
1
4.5
1.1 5
0.3 11
0.5 9
0.9 7.5
0.8 7.5
0.7 7.5
2100
900
900
1300
1300
1800
1800
1500
1500
1600
700
700
1000
1000
1500
1500
1200
1200
1300
600
600
700
700
1200
1200
1000
1000
1200
1200
1100
450
650
900
900
750
980
300
300
500
500
980
980
830
830
980
300
300
500
500
980
980
830
830
900
280
280
350
350
900
900
750
750
900
900
900
230
380
750
750
630
38.6
11.8
11.8
19.7
19.7
38.6
38.6
32.7
32.7
38.6
11.8
11.8
19.7
19.7
38.6
38.6
32.7
32.7
35.4
11.0
11.0
13.8
13.8
35.4
35.4
29.5
29.5
35.4
35.4
35.4
9.1
15.0
29.5
29.5
24.8
0.2
3
0.07 5
0.06 5
0.12 4.5
0.11 4.5
0.24 3
0.22 3
0.2
3
0.12 3
0.24 3.5
0.07 6.5
0.06 6.5
0.12 6
0.11 6
0.24 4.5
0.22 4.5
0.2
4.5
0.2
4.5
0.24 5
0.11 8
0.1
8
0.14 7.5
0.13 7.5
0.4
6
0.3
6
0.3
6
0.2
6
0.4
4.5
0.3
4.5
0.4
5
0.1 11
0.2
9
0.4
7.5
0.3
7.5
0.3
7.5
SOLID END MILLS
Dia.
Depth of cut
VFHVRB
I170
I259
CUTTING CONDITIONS
- Inch sizes
VFHVRB
Work material
Carbon Steel, Cast Iron,

Alloy Steel ( 30HRC)

Pre-haedened steel
Hardened Steel (45 55HRC)
AISI 1049, AISI 30, AISI P20
AIAI H13, AISI W1-10, AISI P21
AISI H13
AISI D2
Neck Revolution Table feed Depth of cut Depth of cut Revolution Table feed Depth of cut Depth of cut Revolution Table feed Depth of cut Depth of cut Revolution Table feed Depth of cut Depth of cut
R
Dia.
Length
ap
ae
ap ae
ap
ap
ae
ae
(inch) (inch) (inch) (min-1) (mm/min) (IPM) (mm) (mm) (min-1) (mm/min) (IPM) (mm) (mm) (min-1) (mm/min) (IPM) (mm) (mm) (min-1) (mm/min) (IPM) (mm) (mm)
0.125
0.125
0.188
0.188
0.250
0.250
0.313
0.313
0.375
0.375
0.500
0.500
0.03
0.03
0.05
0.05
0.06
0.06
0.08
0.08
0.08
0.08
0.12
0.12
0.375
0.625
0.563
0.938
0.750
1.250
0.938
1.563
1.125
1.875
1.500
2.500
16000
16000
12000
12000
8000
8000
6000
6000
4800
4800
4000
4000
11000 433.1
9000 354.3
12000 472.4
12000 472.4
13000 511.8
13000 511.8
13000 511.8
13000 511.8
13000 511.8
13000 511.8
12000 472.4
12000 472.4
0.24
0.22
0.3
0.27
0.5
0.45
0.6
0.54
0.6
0.54
0.9
0.8
1
1
1.5
1.5
2
2
3
3
4.5
4.5
4.5
4.5
13000
13000
10000
10000
6600
6600
5000
5000
4000
4000
3300
3300
7800
6400
8500
8500
9200
9200
9200
9200
9200
9200
8500
8500
307.1
252
334.6
334.6
362.2
362.2
362.2
362.2
362.2
362.2
334.6
334.6
0.19
0.17
0.23
0.21
0.4
0.35
0.46
0.42
0.46
0.42
0.7
0.6
1
11000 6300 248 0.14 1
1
11000 5100 200.8 0.13 1
1.5 8000 6800 267.7 0.18 1.5
1.5 8000 6800 267.7 0.16 1.5
2
5400 7400 291.3 0.3 2
2
5400 7400 291.3 0.27 2
3
4000 7400 291.3 0.36 3
3
4000 7400 291.3 0.32 3
4.5 3200 7400 291.3 0.36 4.5
4.5 3200 7400 291.3 0.32 4.5
4.5 2700 6800 267.7 0.45 4.5
4.5 2700 6800 267.7 0.4 4.5
8000
8000
6000
6000
4000
4000
3000
3000
2400
2400
2000
2000
2800
2300
3000
3000
3300
3300
3300
3300
3300
3300
3000
3000
110.2
90.6
118.1
118.1
129.9
129.9
129.9
129.9
129.9
129.9
118.1
118.1
0.07
0.07
0.1
0.08
0.15
0.14
0.18
0.16
0.18
0.16
0.23
0.2
1
1
1.5
1.5
2
2
3
3
4.5
4.5
4.5
4.5
Depth of cut
SOLID END MILLS
Work material
Carbon Steel, Cast Iron,

Alloy Steel ( 30HRC)

Pre-haedened steel
AISI 1049, AISI 30, AISI P20
AIAI H13, AISI W1-10, AISI P21
AISI H13
AISI D2
Neck Revolution Table feed Depth of cut Depth of cut Revolution Table feed Depth of cut Depth of cut Revolution Table feed Depth of cut Depth of cut Revolution Table feed Depth of cut Depth of cut
R
Dia.
Length
ap
ae
ap ae
ap
ap
ae
ae
(inch) (inch) (inch) (min-1) (mm/min) (IPM) (mm) (mm) (min-1) (mm/min) (IPM) (mm) (mm) (min-1) (mm/min) (IPM) (mm) (mm) (min-1) (mm/min) (IPM) (mm) (mm)
0.125
0.125
0.188
0.188
0.250
0.250
0.313
0.313
0.375
0.375
0.500
0.500
0.03
0.03
0.05
0.05
0.06
0.06
0.08
0.08
0.08
0.08
0.12
0.12
0.375
0.625
0.563
0.938
0.750
1.250
0.938
1.563
1.125
1.875
1.500
2.500
9600
9600
7200
7200
4000
4800
3600
3600
2900
2900
2400
2400
3300
2700
3600
3600
3300
3900
3900
3900
3900
3900
3600
3600
129.9
106.3
141.7
141.7
129.9
153.5
153.5
153.5
153.5
153.5
141.7
141.7
0.5
0.5
0.6
0.6
0.5
1
1.2
1.1
1.2
1.1
1.8
1.6
1
1
1.5
1.5
3
2
3
3
4.5
4.5
4.5
4.5
8000
8000
6000
6000
3300
4000
3000
3000
2400
2400
2000
2000
2300
1900
2500
2500
2300
2700
2700
2700
2700
2700
2500
2500
90.6
74.8
98.4
98.4
90.6
106.3
106.3
106.3
106.3
106.3
98.4
98.4
0.4
0.35
0.5
0.4
0.4
0.8
1
0.9
1
0.9
1.4
1.3
1
1
1.5
1.5
3
2
3
3
4.5
4.5
4.5
4.5
6400
6400
4800
4800
2700
3200
2400
2400
1900
1900
1600
1600
1800
1500
2000
2000
1800
2200
2200
2200
2200
2200
2000
2000
70.9
59.1
78.7
78.7
70.9
86.6
86.6
86.6
86.6
86.6
78.7
78.7
0.3
0.25
0.36
0.32
0.3
0.6
0.7
0.7
0.7
0.7
1.1
1
1
1
1.5
1.5
3
2
3
3
4.5
4.5
4.5
4.5
4800
4800
3600
3600
2000
2400
1800
1800
1500
1500
1200
1200
830
680
900
900
830
980
980
980
980
980
900
900
32.7
26.8
35.4
35.4
32.7
38.6
38.6
38.6
38.6
38.6
35.4
35.4
0.14
0.13
0.12
0.11
0.1
0.2
0.24
0.22
0.24
0.22
0.4
0.3
1
1
1.5
1.5
3
2
3
3
4.5
4.5
4.5
4.5
Depth of cut
I260
VFHVRB
I172
VFMHVCH
VFMHVRBCH
End mill, Medium cut length, 4 ute, Irregular helix utes, with multiple internal through coolant holes Corner radius end mil , Medium cut length, 4 ute, Irregular helix utes, with multiple internal through coolant holes
y Slotting
y Shoulder milling
Work
Titanium alloy
material
Inconel718 etc.
Table feed
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
16
20
2000
1600
560
510

Work
Titanium alloy
material
22.0
20.1
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
800
600
110
100
4.3
3.9
Table feed
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
16
20
1400
1100
170
130
Depth of
Depth of
cut
cut
D:Dia.
6.7
5.1
D:Dia.
VF6MHVCH
VF6MHVRBCH
End mil , Medium cut length, 6 ute, Irregular helix utes with multiple internal through coolant holes Corner radius end mil , Medium cut length, 6 ute, Irregular helix utes, with multiple internal through coolant holes
y Shoulder milling
Work
Titanium alloy
material
Table feed
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
16
20
3000
2400
1600
1400
63.0
55.1
SOLID END MILLS
Inconel718 etc.
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
800
640
180
150
7.1
5.9
Depth of
cut
D:Dia.
VFMHVCH
I143
VF6MHVCH
I146
VFMHVRBCH
I174
VF6MHVRBCH
I176
I261
CUTTING CONDITIONS
VF8MHVCH
VF8MHVRBCH
End mil , Medium cut length, 8 ute, Irregular helix utes with multiple internal through coolant holes Corner radius end mil , Medium cut length, 8 ute, Irregular helix utes, with multiple internal through coolant holes
y Shoulder milling
Work
Titanium alloy
material
Inconel718 etc.
Table feed
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
16
20
3000
2400
2100
1900
82.7
74.8
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
800
640
240
200
9.4
7.9
Depth of
cut
D:Dia.
VFSFPRCH
Roughing end mill, Short cut length, 4 ute, with multiple internal through coolant holes
SOLID END MILLS
y Shoulder milling
y Slotting

Work
Titanium alloy
material
Inconel718 etc.
Table feed
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
16
20
1200
1000
300
300

Work
Titanium alloy
material
11.8
11.8
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
800
600
110
100
4.3
3.9
Table feed
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
16
20
800
600
100
80
Depth of
Depth of
cut
cut
D:Dia.
3.9
3.1
D:Dia.
I262
VF8MHVCH
I147
VF8MHVRBCH
I177
VFSFPRCH
I151
VF6SVRCH
Roughing end mill, Short cut length, 6 ute, Irregular helix utes, with multiple internal through coolant holes
y Shoulder milling
Work
Titanium alloy
material
Inconel718 etc.
Table feed
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
16
20
2400
2000
1200
1000
47.2
39.4
Table feed
(IPM)
Revolution
(min-1)
(mm/min)
800
640
160
140
6.3
5.5
Depth of
cut
D:Dia.
SOLID END MILLS
VF6SVRCH
I152
I263
CUTTING CONDITIONS
DF4JC
End mill, Semi long cut length, 4 ute, For graphite
Work
material
Graphite
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
3
4
6
8
10
12
22000
18000
14000
10500
8700
7200
2500
2900
3200
2900
2600
2200
98.4
114.2
126.0
114.2
102.4
86.6
0.05D
Depth of
cut
2D
D:Dia.
SOLID END MILLS
1) When high machining accuracy is needed, or the workpiece becomes chipped, we recommend lowering the feed rate.
2) Use a milling machine dedicated for graphite.
I264
DF4JC
I178
DF4XL
End mill, Long neck, 4 ute, For graphite
y Shoulder milling
Dia.
(mm)
1.5
4
6
8
10
12
Work material
Graphite
Table feed
Neck length
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
6
8
10
10
16
10
16
20
16
20
30
20
40
30
30
30
30
30000
25000
22000
25000
18000
22000
19000
16000
21000
18000
14000
18000
13000
14000
10500
8700
7200
1300
1000
700
1200
800
1500
1100
800
1900
1500
1000
2400
1500
3200
2900
2600
2200
51.2
39.4
27.6
47.2
31.5
59.1
43.3
31.5
74.8
59.1
39.4
94.5
59.1
126.0
114.2
102.4
86.6
Depth of cut
Dia.
(mm)
1.5
4
6
8
10
12
Graphite
Neck length Revolution

(min-1)
(mm)
6
8
10
10
16
10
16
20
16
20
30
20
40
30
30
30
30
30000
25000
22000
25000
18000
22000
19000
16000
21000
18000
14000
18000
13000
14000
10500
8700
7200
Table feed
(IPM)
(mm/min)
1000
700
500
1100
600
1200
800
600
1400
1100
700
1800
900
2300
2000
1900
1700
39.4
27.6
19.7
43.3
23.6
47.2
31.5
23.6
55.1
43.3
27.6
70.9
35.4
90.6
78.7
74.8
66.9
Depth of cut
(mm)
0.1
0.08
0.06
0.14
0.1
0.2
0.16
0.12
0.3
0.25
0.2
0.5
0.4
1.2
2
3
4
Depth of cut
D:Dia.
D:Dia.
3) If the rigidity of the machine or the workpiece installation is very low, or chattering is generated, please reduce the revolution and the feed rate
proportionately.
DF4XL
I179
SOLID END MILLS
Work material
y Slotting
I265
CUTTING CONDITIONS
DF2MB
Work material
R
(mm)
R3
R4
R5
R6
Graphite
Table feed
Overall length
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
100
150
110
150
120
180
130
200
10000 16000
6000 10000
9000 12000
5000 9000
7500 10000
5000 7500
6000 8000
4000 6000
1200 2100
600 1200
1500 2200
700 1500
1700 2400
1000 1700
1300 1900
800 1300
47.2 82.7
23.6 47.2
59.1 86.6
27.6 59.1
66.9 94.5
39.4 66.9
51.2 74.8
31.5 51.2
0.6
0.4
0.8
0.6
1
0.8
1.2
1
1.5
1.2
2
1.6
2.5
2
3
2.5
Depth of cut
SOLID END MILLS
3) If the rigidity of the machine or the workpiece installation is very low, or chattering is generated, please reduce the revolution
and the feed rate proportionately.
I266
DF2MB
I180
DF2XLB
R
(mm)
R0.2
R0.25
R0.3
R0.4
R0.5
R0.75
R1
R1.5
R2
Graphite
Table feed
Neck length
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
1
2
3
4
8
12
4
2
4
6
10
16
6
8
4
6
8
10
12
20
30
40
8
10
16
30
8
10
12
16
20
25
40
60
16
25
40
60
20
30
40
60
40000
40000
40000
40000
30000
20000
40000
40000
40000
40000
35000
22000
40000
40000
40000
40000
40000
40000
40000
30000
20000
15000
40000
40000
35000
27000
40000
40000
35000
30000
30000
25000
20000
15000
28000
20000
16000
14000
21000
15000
13000
12000
1500
1500
1300
1300
800
450
1500
1800
1500
1500
1000
530
1700
1700
2500
2500
2000
2000
2000
1100
600
400
2800
2800
2000
1000
3000
3000
2500
2000
2000
1500
1000
500
3000
2000
1500
1000
3000
2000
1600
1400
59.1
59.1
51.2
51.2
31.5
17.7
59.1
70.9
59.1
59.1
39.4
20.9
66.9
66.9
98.4
98.4
78.7
78.7
78.7
43.3
23.6
15.7
110.2
110.2
78.7
39.4
118.1
118.1
98.4
78.7
78.7
59.1
39.4
19.7
118.1
78.7
59.1
39.4
129.9
78.7
63.0
55.1
0.05
0.05
0.04
0.04
0.03
0.03
0.05
0.07
0.06
0.06
0.05
0.04
0.08
0.08
0.12
0.1
0.1
0.1
0.1
0.08
0.06
0.04
0.15
0.15
0.15
0.1
0.23
0.2
0.2
0.2
0.2
0.18
0.15
0.1
0.3
0.25
0.2
0.17
0.5
0.4
0.35
0.3
0.15
0.12
0.12
0.1
0.1
0.08
0.15
0.2
0.18
0.15
0.15
0.12
0.2
0.15
0.3
0.3
0.25
0.2
0.2
0.2
0.15
0.12
0.45
0.45
0.3
0.3
0.7
0.6
0.6
0.5
0.5
0.45
0.4
0.3
0.9
0.75
0.6
0.45
1.5
1.2
1
0.9
SOLID END MILLS
Work material
Depth of cut
DF2XLB
I181
I267
CUTTING CONDITIONS
DF3XB
Work material
R
(mm)
R0.5
R1
R1.5
R2
Graphite
Table feed
Neck length
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
30
40
50
40
60
80
60
80
100
20000
15000
12000
20000
15000
12000
14000
12000
10000
1100
750
500
1800
900
600
1700
1200
1100
43.3
29.5
19.7
70.9
35.4
23.6
66.9
47.2
43.3
0.05
0.04
0.03
0.13
0.09
0.07
0.15
0.12
0.2
0.13
0.11
0.1
0.4
0.27
0.2
0.45
0.35
0.5
Depth of cut
SOLID END MILLS
I268
DF3XB
I183
DFPSRB
Corner radius end mill, Short cut length, 2-4 ute, High precision, For graphite
Dia.
(mm)
0.5
0.8
1.5
6
8
10
12
Graphite
Table feed
R
(mm)
Neck length
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.5
0.2
0.2
0.5
0.5
0.5
1
0.5
1
0.5
1
0.5
4
5
6
10
15
6
8
8
12
8
12
16
20
30
10
20
12
16
20
30
40
20
40
20
20
40
20
40
30
30
30
30
40
40
40
30000
28000
25000
22000
20000
28000
22000
25000
22000
25000
22000
18000
15000
12000
25000
18000
22000
19000
16000
13000
11000
18000
12000
18000
18000
13000
18000
13000
14000
14000
10500
10500
8700
8700
7200
1100
960
850
600
500
1300
900
1500
1300
1500
1300
1000
800
600
2100
1400
3000
2500
2000
1600
1200
3000
1800
3000
4200
2800
4200
2800
4600
4600
4000
4000
3500
3500
3000
43.3
37.8
33.5
23.6
19.7
51.2
35.4
59.1
51.2
59.1
51.2
39.4
31.5
23.6
82.7
55.1
118.1
98.4
78.7
63.0
47.2
118.1
70.9
118.1
165.4
110.2
165.4
110.2
181.1
181.1
157.5
157.5
137.8
137.8
118.1
0.05
0.05
0.05
0.04
0.03
0.08
0.08
0.1
0.1
0.1
0.1
0.08
0.08
0.07
0.15
0.15
0.2
0.2
0.2
0.16
0.14
0.3
0.25
0.3
0.4
0.4
0.4
0.4
0.6
0.6
0.8
0.8
1
1
1.2
0.23
0.23
0.23
0.21
0.18
0.45
0.45
0.6
0.6
0.45
0.45
0.4
0.4
0.35
0.8
0.8
1.2
1.2
1.2
1
0.8
2
1.7
1.5
2.7
2.7
2.3
2.3
3.8
3
5.3
4.5
6.8
6
8
SOLID END MILLS
Work material
Depth of cut
DFPSRB
I184
I269
CUTTING CONDITIONS
CBN2XLB
Work
material
R
(mm)
R0.2
R0.3
R0.4
R0.5
R0.75
R1
AISI H13 etc.
AISI D2 etc.
Table feed
Revolution
50000
50000
50000
50000
50000
50000
1500
2000
3000
3000
3500
4000
59.1
78.7
118.1
118.1
137.8
157.5

Table feed
ap
ae
(mm)
(mm)
0.006
0.01
0.02
0.03
0.04
0.05
0.01
0.02
0.05
0.06
0.08
0.1
50000
50000
50000
50000
50000
50000
1200
1500
2000
2000
2500
3000
47.2
59.1
78.7
78.7
98.4
118.1

Table feed
ap
ae
(mm)
(mm)
0.006
0.01
0.02
0.03
0.03
0.04
0.01
0.02
0.04
0.05
0.06
0.07
50000
50000
50000
50000
50000
50000
1200
1500
2000
2000
2500
3000
47.2
59.1
78.7
78.7
98.4
118.1

ap
ae
(mm)
(mm)
0.004
0.008
0.015
0.02
0.02
0.03
0.008
0.015
0.03
0.03
0.04
0.05
Depth of
cut
SOLID END MILLS
2) Oil mist coolant is recommended.
I270
CBN2XLB
I186
CBN2XLRB
Work
material
AISI H13 etc.
AISI D2 etc.
Dia.
(mm)
Table feed
Revolution
0.5
1
1.5
2
50000
38000
25000
20000
750
1100
900
800
29.5
43.3
35.4
31.5
Table feed
ap (mm) ae (mm) (min-1) (mm/min) (IPM)
0.01
0.02
0.03
0.04
0.2
0.3
0.5
0.7
50000
38000
25000
20000
600
760
700
600
23.6
29.9
27.6
23.6
Table feed
ap (mm) ae (mm) (min-1) (mm/min) (IPM)
0.01
0.01
0.02
0.03
0.1
0.2
0.4
0.6
40000
25000
17000
12000
400
400
340
300
15.7
15.7
13.4
11.8

ap (mm) ae (mm)
0.005
0.01
0.02
0.02
0.06
0.1
0.2
0.3
Depth of
cut
SOLID END MILLS
2) Oil mist coolant is recommended.
CBN2XLRB
I187
I271
CUTTING CONDITIONS
C2SA
MS2XB
2
Ball
ute,
nose
Short
end cut
mill,length,
2 ute,Relieved
Taper neck
neck, For aluminum alloy
y Shoulder milling
Work
material
y Slotting
Work
material
Aluminum alloy
Table feed
Aluminum alloy
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
3
4
5
6
8
10
12
16
20
40000
36000
30000
27000
20000
16000
13000
10000
8000
1800
2400
3000
3200
3400
3600
3600
3600
3300
70.9
94.5
118.1
126.0
133.9
141.7
141.7
141.7
129.9
3
4
5
6
8
10
12
16
20
40000
36000
30000
27000
20000
16000
13000
10000
8000
1600
2100
2700
2800
3000
3200
3200
3200
3000
63.0
82.7
106.3
110.2
118.1
126.0
126.0
126.0
118.1
Depth of
cut
Depth of
cut
D:Dia.
D:Dia.
SOLID END MILLS
1) Water-soluble cutting uid is recommended.

2) Climb cutting is recommended for shoulder milling.
3) If the tooling clamping is insufcient, the tool can be pulled at of the holder therefore ensure that is securely located.
4) The above are for L/D of up to 4. If exceeding L/D of 4 reduce the speed, feed and depth of cut proportionally.
5) If the rigidity of the machine or the workpiece installation is very low, or chattering and noise are generated, please reduce the revolution
C3SA
C3SARB
3 ute, Short cut length, Relieved neck, For aluminum alloy Corner radius, Short cut length, 3 ute, For aluminum alloy
y Shoulder milling
Work
material
y Slotting
Work
material
Aluminum alloy
Table feed
Aluminum alloy
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
12
16
18
20
25
13000
10000
9000
8000
6000
5400
5400
5000
5000
4500
212.6
212.6
196.9
196.9
177.2
12
16
18
20
25
13000
10000
9000
8000
6000
3200
3200
3000
3000
2800
126.0
126.0
118.1
118.1
110.2
Depth of
cut
Depth of
cut
D:Dia.
D:Dia.

2) If the rigidity of the machine or the workpiece installation is very low, or chattering is generated, please reduce the revolution and feed rate
proportionately, or set the depth of cut smaller.
4) The above are for L/D of up to 4. If exceeding L/D of 4 reduce the speed, feed and depth of cut proportionally.
5) Not center cutting edge therefore vertical feed can not be carried at. If vertical feed is necessary please use ramping.
I272
C2SA
I188
C3SA
I189
C3SARB
I191
C2MHA
MS2XLRB
2
ute, Medium
cutmill,
length,
Relieved
neck2, For
alloy
Corner
radius end
Short
cut length,
ute,aluminum
Long neck
y Shoulder milling
Work
material
y Slotting
Work
material
Aluminum alloy
Table feed
Aluminum alloy
Table feed
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
Dia.
(mm)
Revolution
(min-1)
(mm/min)
(IPM)
3
4
5
6
8
10
12
16
20
25
40000
36000
30000
27000
20000
16000
13000
10000
8000
6000
2400
2600
4000
4000
4000
4500
4500
4500
4300
3600
94.5
102.4
157.5
157.5
157.5
177.2
177.2
177.2
169.3
141.7
3
4
5
6
8
10
12
16
20
25
40000
36000
30000
27000
20000
16000
13000
10000
8000
6000
1500
1800
2800
2800
2800
3200
3200
3200
3000
2500
59.1
70.9
110.2
110.2
110.2
126.0
126.0
126.0
118.1
98.4
Depth of
cut
Depth of
cut
D:Dia.
D:Dia.
SOLID END MILLS

3) If the tooling clamping is insufcient, the tool can be pulled at of the holder therefore ensure that is securely located.
4) If the rigidity of the machine or the workpiece installation is very low, or chattering and noise are generated, please reduce the revolution
C2MHA
I190
I273
GUIDE TO MILLING TOOL INSERTS

aOrganization
for Milling insert Standards section
zOrganized according to cutter type then, its respective

insert description number.
xCutters are arranged in alphabetical order.
aOrganization
for Classication section
zClassied into milling inserts and wiper inserts.

xInserts are arranged in alphabetical order.
ORGANIZED ACCORDING TO CUTTER TYPE

IN ALPHABETICAL ORDER
INSERT DESCRIPTION NUMBER
INSERT TOLERANCE
INSERTS ARE ARRANGED
IN ALPHABETICAL ORDER
INSERT GRADE
INSERT
DIMENSIONS
CUTTER TYPE &

PHOTO OF INSERT
MILLING INSERTS
P
M
K
N
S
H
Work Material
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
Honing :
E : Round F : Sharp S : Chamfer + Round
Dimensions (inch)
NNMU200608ZEN-HK
(ISO) Number
AHX640 ^K014
NNMU200608ZEN-MK
AHX640 ^K014
NNMU200608ZEN-HK
NNMU200608ZEN-MK
Class
Honing
FH7020
MC5020
VP15TF
VP30RT
TF15
Order Number
Insert Geometry
Order Number
: Stable Cutting
: General Cutting
: Unstable Cutting
Coated Carbide
Cutter Type
CLASSIFICATION
L1
L2
D1
S1
F1
Re
M E
.787
.258
.031
M E
AEMW150304ER
150304FR
150304FR
150308ER
150308ER
150308FR
150308FR
1503062ER
1503062ER
1503093ER
1503093ER
1503125ER
1503250ER
.787
.258
.031
(ISO) Number
AEMW150304ER
Cutter Type
AHX640 ^K014
.787
.258
(ISO) Number
APMT1135PDER-H1
1135PDER-H2
1135PDER-H2
Cutter Type
1135PDER-H6
APMT1135PDER-M0
1135PDER-M1
1135PDER-M1
1135PDER-M2
1135PDER-M2
APGT1604PDFR-G2
APGT1604PDFR-G2
APMT1604PDER-H1
APMT1604PDER-H1
19T3093ER
1604PDER-H2
1604PDER-H2
19T3125ER
1604PDER-H4
19T3250ER
1604PDER-H6
Page
BAP300
^K066
1135PDER-H4
1135PDER-H6
APMT1135PDER-M0
1503125ER
J017
J017
1503250ER
AEMW19T304ER
AEMW19T304ER
19T304FR
19T304FR
19T308ER
19T308ER
19T308FR
19T308FR
19T3062ER
19T3062ER
19T3093ER
19T3125ER
19T3250ER
123608PEFR-GM
Order Number
APMT1135PDER-H1
1135PDER-H4
J016
BAE600
BAP400
^K066
J017
J017
AOGT123602PEFR-GM AOGT123602PEFR-GM APX3000

123604PEFR-GM
123604PEFR-GM ^K030
WNEU2006ZEN7C-WK WNEU2006ZEN7C-WK M E
Page
BAE500
123608PEFR-GM
J012
1604PDER-H4
J017
1604PDER-H6
1604PDER-H8
1604PDER-H8
APMT1604PDER-M2
APMT1604PDER-M2
APMT1604PDER
APMT1604PDER
CCMX083508ENA
CCMX083508EN-A
J018
AOMT123604PEER-H AOMT123604PEER-H
.031
123608PEER-H
123608PEER-H
123616PEER-H
123616PEER-H
J013
J032
JOMW06T215ZZSR-FT JOMW06T215ZZSR-FT M S
080320ZZSR-FT
080320ZZSR-FT M S
JDMW09T320ZDSR-FT JDMW09T320ZDSR-FT M S
AJX ^K088
a a
.250
.109
.047
.059
a a
.315
.125
.055
.079
a a
.375
.156
.071
.079
120420ZDSR-FT M S
a a
.472
.187
140520ZDSR-FT
140520ZDSR-FT M S
a a
.551
JOMT06T215ZZSR-JM
JOMT06T215ZZSR-JM M S
a a
.250
080320ZZSR-JM
080320ZZSR-JM M S
JDMT09T320ZDSR-JM JDMT09T320ZDSR-JM M S
120420ZDSR-FT
*
*JOMW... : 13, JDMW... : 15
AJX ^K088
.098
.079
.219
.110
.079
.109
.047
.059
a a
.315
.125
.055
a a
.375
.156
.071
120420ZDSR-JM
120420ZDSR-JM M S
a a
.472
.187
.098
.079
140520ZDSR-JM
140520ZDSR-JM M S
a a
.551
.219
.110
.079
JDMT120420ZDSR-ST
JDMT120420ZDSR-ST M S
a a
.472
.187
.098
.079
140520ZDSR-ST
140520ZDSR-ST M S
a a
.551
.219
.110
.079
.079
.079
JOMW... : 13, JDMW... : 15
AJX ^K088
APX3000 ^K030
AOGT123602PEFR-GM AOGT123602PEFR-GM G F
.472
123604PEFR-GM
123604PEFR-GM G F
.472
123608PEFR-GM
123608PEFR-GM G F
.472
.260
.260
.260

.142
.142
.142
.071
.063
.047
AOMT123602PEER-M AOMT123602PEER-M
.008
.016
.031
123604PEER-M
123604PEER-M
123608PEER-M
123608PEER-M
123610PEER-M
123610PEER-M
123612PEER-M
123612PEER-M
123616PEER-M
123616PEER-M
123620PEER-M
123620PEER-M
123624PEER-M
123624PEER-M
123630PEER-M
123630PEER-M
123632PEER-M
123632PEER-M
J013
09T308ENA
09T308EN-A
CCMX09T308ENB
CCMX09T308EN-B
CPMT1205ZPEN-M2
CPMT1205ZPEN-M2
1205ZPEN-M3
1205ZPEN-M3
184816PEER-H
184816PEER-H
184832PEER-H
184832PEER-H
184840PEER-H
184840PEER-H
184850PEER-H
184850PEER-H
184864PEER-H
184864PEER-H
120420ZDSR-FT
120420ZDSR-FT
140520ZDSR-FT
140520ZDSR-FT
J013
080320ZZSR-FT
184808PEER-M
184808PEER-M
184810PEER-M
184812PEER-M
184812PEER-M
184816PEER-M
184816PEER-M
120420ZDSR-JM
120420ZDSR-JM
184820PEER-M
184820PEER-M
140520ZDSR-JM
140520ZDSR-JM
LEGEND FOR STOCK

STATUS MARK
080320ZZSR-JM
BAP300
J000
Order:
140520ZDSR-ST
PRODUCT SECTION
General Cutting
Unstable Cutting
PAGE TITLE BY TOOL APPLICATION
aTo
140520ZDSR-ST
PAGE TITLE

J012
JDMT120420ZDSR-ST JDMT120420ZDSR-ST
STOCK STATUS

Stable Cutting
080320ZZSR-JM
JDMT09T320ZDSR-JM JDMT09T320ZDSR-JM
J036

J012
JOMT06T215ZZSR-JM JOMT06T215ZZSR-JM
J013
J017
J023
080320ZZSR-FT ^K088
JDMW09T320ZDSR-FT JDMW09T320ZDSR-FT
^K066
J012
PMR
^K137
JOMW06T215ZZSR-FT JOMW06T215ZZSR-FT AJX
184810PEER-M
APGT1135PDFR-G2
J021
J021
AOMT184804PEER-H AOMT184804PEER-H APX4000

184808PEER-H ^K038
184808PEER-H
APGT1135PDFR-G2
LER
^K078
PAGE REFERENCE
indicates the reference pages for
detailed standards of specic inserts.
J012

a GRADE
a SINTERED CBN / PCD
IDENTIFICATION ...................................................
GRADES FOR MILLING ........................................
MILLING APPLICATION RANGE ..........................
COATED CARBIDE(CVD and PVD) .............................
CERMET ................................................................
CEMENTED CARBIDE ..........................................
CBN(SINTERED CBN) ...................................................
PCD(SINTERED DIAMOND) .............................................
J002
J004
J005
J006
J008
J009
J010
J011
STANDARD MILLING INSERTS

ROTATING INSERTS ......................................... J012
CBN AND PCD ................................................... J034
CLASSIFICATION.................................................. J036
J001
IDENTIFICATION
y ISO CODES FOR MILLING
Symbol
Symbol
Insert Shape
Relief Angle
Octagonal
15
Square
20
Triangular
25
Rhombic 80
30
Rhombic 86
Parallelogram 85
11
Round
Other
Special Design
Other
Wiper
Major Relief Angle
z Insert Shape
x Relief Angle
INCH
METRIC
c Tolerance Class
v Chip Breaker With or Without Hole
Metric
Class
C
E
J002
D1 (I.C.) Tolerance of I.C.
S1
.250
.375
.500
.625
e.001
e.0005
e.001
e.001
e.001
e.001
.250
.375
.500
.625
.250
.375
.500
.625
.250
.375
.500
.625
e.002
e.002
e.003
e.003
e.002
e.002
e.003
e.004
e.002
e.002
e.003
e.004
e.0005
e.0005
e.0005
e.0005
e.003
e.003
e.006
e.006
e.003
e.003
e.005
e.006
e.001
e.001
e.001
e.001
e.001
e.001
e.001
e.001
e.005
e.005
e.005
e.005
Hole
ChipConguration breakers Figure
Symbol
Hole
With Hole
With Hole
With Hole
Without
Hole
No
Without
Hole
Onesided
Cylindrical
Hole
+
One
Countersink
(40 60)
Cylindrical
Hole
+
One
Countersink
(70 90)
No
Onesided
No
Special
Design
E
Round
Metric
Diameter of
Inscribed
Circle
(inch)
F
Sharp
.250
06
06
11
.313
08
07
13
.375
09
09
16
.394
10
.472
12
.500
.625
.787
Chamfer
.394
R
R
Chamfer+Hone
Inch
Thickness
(inch)
Metric
T3
12
12
22
2.5
.156
16
15
27
.125
03
.187
04
20
n Insert Thickness
b Insert Size
m Cutting Edge Angle
, Wiper Edge Relief Angle
45
15
75
20
90
25
/ Cutting Direction
L
Left
Neutral
Right
11 Width of Wiper Edge
.055
.094
Round(small)
Z
Chamfer
. Cutting Edge Condition
12 Molded Chipbreaker for Milling
Inch
J003
GRADES FOR MILLING

a INDEXABLE INSERT GRADES FOR MILLING
ISO
Coated Carbide
CVD
PVD
P01
Steel
P10
P20
P30
P40
Stainless Steel
M01
M10
M20
M30
M40
K01
K10
K20
MP8010
Cast Iron
K30
Non-Ferrous Metal
N01
N10
N20
N30
Hardened Steel
S01
S20
S30
H01
H10
H20
H30
J004
MP9030
S10
MP8010
S
Heat Resistant Alloy Ti Alloy
Cermet
Cemented
Carbide
CBN
(Sintered CBN)
PCD
(Sintered
Diamond)
MILLING APPLICATION RANGE

P
STEEL
STAINLESS STEEL
Cutting Speed (SFM)
Cermet
CVD Coated Carbide
PVD Coated Carbide

Cermet
Cutting Speed (SFM)
Cermet
CVD Coated Carbide
PVD Coated Carbide

Cermet
Cemented Carbide
Cemented Carbide
Feed (inch/tooth)
CAST IRON
NON-FERROUS METAL
Sintered CBN
Cermet
CVD Coated Carbide

PVD Coated Carbide
Cemented Carbide
Feed (inch/tooth)
Cutting Speed (SFM)
Cutting Speed (SFM)
Sintered Diamond
Feed (inch/tooth)
Cemented Carbide
Feed (inch/tooth)
J005

a Coating Layers
(Wear Resistance)
(Thermal Shock Resistance)
(Improved Welding Resistance)
COATED CARBIDE (CVD&PVD)

<CVD>
a Special tough brous structure improves wear
and fracture resistance.
a It covers a wide application range and thus
a Substrate
reduces the number of tools required.

PVD
<
>
a PVD coating prolongs tool life.
a Coating of tools with sharp edges is possible without
softening or changing the quality of the substrate.
SELECTION STANDARD
a MILLING
Work Material
VP15TF
Recommended Cutting
Speed (SFM)
755
(490 985)
655
(490 820)
575
(400 750)
575
(400 750)
390
(330 490)
755
(490 985)
655
(490 820)
490
(330 655)
490
(330 655)
390
(330 490)
590
(330 820)
655
(490 820)
490
(330 655)
490
(330 655)
LC15TF
1000
(200 3000)
Recommended Grade
F7010
F7030
Steel
VP15TF
VP30RT
UP20M
F7010
F7030
Stainless
Steel
VP15TF
VP30RT
UP20M
MC5020
F5010
Cast Iron
F5020
ISO
Application Range
P01
P10
P20
P30
P40
M01
M10
M20
M30
M40
K01
K10
K20
K30
N10
Aluminum Alloy
N20
S01
VP15TF
100
(65 130)
Ti Alloy
S10
S20
S30
H01
Hardened
Materials
VP15TF
80
(50 110)
H10
H20
H30
J006
MP9030
Heat Resistant
Alloy
MP8010
N30
FEATURES OF VP (MIRACLE) COATING
Substrate
Compared to conventional coating technology, VP

(MIRACLE) coating features (Al,Ti)N coating with highly
increased heat resistance and adhesion strength.
Coating Layer
Hardness
(HRA)
T.R.S
(GPa)
MC5020
F7010
FH7020
F7030
MP8010
MP9030
VP15TF
VP20RT
VP30RT
UP20M
91.0
89.0
88.8
88.8
93.5
90.5
91.5
90.5
88.8
90.5
2.2
2.6
2.8
2.8
2.3
2.5
2.5
2.5
2.8
2.0
Composition
Thickness
Thick
TiCN-Al2O3-TiN
Thin
Thick
TiCN-Al2O3-TiN
Thin
(Al,Ti, Si)N
Thin
(Al,Ti)N-Ti Compound
Thin
(Al,Ti)N
Thin
(Al,Ti)N
Thin
(Al,Ti)N
Thin
TiN
Thin
MIRACLE Coating
Oxidation Temperature
Grade
Increased
Heat Resistance
Increased
Adhesion Strength
Competitor's Coating Grade
*1GPa=102kg/mm
2
Adhesion Strength
Tool
ASX445R0607E
Tool
AHX640WR0620F
Insert (Grade)
SEMT13T3AGSN-JM (VP15TF)
Insert (Grade)
NNMU200608ZEN-MK (MC5020)
Gray cast iron (Scaled)
Welding parts
Workpiece
Workpiece
Machine parts
655
.011
.118
Cutting time (min/corner)
Cutting
Conditions
Cutting Speed (SFM)

Feed per Tooth (IPR)
Depth of Cut (inch)
Normal wear
condition
Results
Competitors
coated
Tool
Insert (Grade)
Results
500
.013
.12 .20
MC5020 enables to extend tool life
three times more than competitors
CVD grade.
Fracture
BXD4000R2504
Tool
Insert (Grade)
XDGT1550PDFR-G04(LC15TF)
Aluminum alloy
AQXUR134SA12L
QOMT0934R-M2(VP30RT)
Carbon steel (Slotting)
Workpiece
Cutting
Conditions
Component
Cutting Speed (SFM)
Depth of Cut (inch)
Revolution
(min-1)
Cutting Speed (SFM)
5,600
3,635
(inch)
.157
(inch)
Width of Cut
.059
.013
Depth of Cut
Chip Discharge (in3/min)

Result
Cutting
Conditions
Cutting Conditions
Workpiece
Cutting Speed (SFM)

(inch/rev)
Feed
2.8
LC15TF produced a superior surface
nish compared to the competitors
non-coated carbide grade that
generated a dull surface nish.
260
.004
Tool life doubled.
Result
J007
CERMET
aNX2525 has high
hardened Ti compound particles within it's

microstructure therefore the grade has
both excellent wear
and fracture resistance properties.
aNX4545 uses a
special alloy for the
binder material
therefore the grade
has high fracture
resistance properties.
a NX2525 for high speed milling.

a NX4545 for general milling.
SELECTION STANDARD
a Milling
Work Material
Recommended Grade
Recommended Cutting
Speed (SFM)
NX2525
820
(490 1150)
ISO
Application Range
P10
M10
P20
M20
Steel
490
(390 590)
NX4545
P30
M30
M
K
K01
655
(490 985)
NX2525
Cast Iron
K10
K20
(Note) In case of wet cutting, please use coated carbide F7030 for steel cutting and coated carbide MC5020 for cast iron cutting.
CUTTING PERFORMANCE
Feed per Tooth : fz Width of Cut : ae
Cutting Performance
Competitor's Cermet C
Fracture
Workpiece : AISI 4140(3.8"W x 15.7"L)
Cutter : SE445R0506E
Insert : SEEN42AFTN1
vc=1150SFM
ap=.098inch
fz=.008inch/tooth
Dry Cutting
Competitor's Cermet A
Fracture
Flank Wear (inch)
Flank Wear (inch)
Steel High Speed Milling
Competitor's Cermet B
Fracture
Competitor's Cermet B
Fracture
Cutting Time (min)
Machined Length per Tooth (feet)
Cast Iron Milling

K10 Cemented Carbide
Flank Wear (inch)
Competitor's Cermet A
Fracture
Workpiece : AISI 40(3.7"W x 15.7"L)
Cutter : SE445R0506E
Insert : SEEN42AFTN1
vc=590SFM
ap=.098inch
fz=.008inch/tooth
Dry Cutting
Machined Length per Tooth (feet)
Grade
NX2525
NX4545
Hardness (HRA)
92.2
90.0
Substrate
Thermal Conductivity
T.R.S.(GPa)
(W/mK)
2.0
2.2
33
33
2
Thermal Expansion
(x 10-6/K)
7.8
7.8
-3
*1GPa=102kg/mm , 1W/m K=2.3910

J008
cal/cm sec r
Steel Shoulder Milling

Workpiece : AISI 4140(220HB)
Cutter : NSE400R503S32
Insert : TEEN43PETR1
vc=655SFM
fz=.014inch/tooth
ae=1inch
ap=.118inch
Down Cut Dry Cutting
CEMENTED CARBIDE
a Available grade series are UTi20T for steel
and cast iron, and HTi10 for cast iron,

non-ferrous metal and non-metal.
K Series Grade (WC-Co)
.394!inch
P,M Series Grade (WC-TiC-TaC-Co)
.394!inch
SELECTION STANDARD
a MILLING
Work Material
Recommended Grade
Recommended Cutting
Speed (SFM)
UTi20T
390
(165 590)
ISO
Application Range
P10
Steel
P20
P30
M10
390
(165 590)
UTi20T
Stainless Steel
M20
M30
K
HTi10
330
(165 490)
UTi20T
390
(165 590)
K10
Cast Iron
K20
K30
N01
N10
HTi10
TF15
Non-Ferrous Metal
1310
(985 1640)
N20
N30
MAIN COMPONENT AND APPLICATION

Main
Component
Characteristics
Work Material
WC-TiC-TaC-Co
High heat resistance and plastic deformation resistance.
Carbon steel, Alloy steel, Stainless steel,

and Cast iron
WC-Co
High rigidity and wear resistance.
Cast iron, Non-Ferrous metals, and Non-metal
ISO
P
K
*For High SFM, cutters need to be balanced. Keep the recommended cutting speed shown in each cutter type page.
ISO
P
K
N
Grade
Thermal
Thermal
Hardness Conductivity
Expansion
(HRA)
(W/mK)
(x10-6/K)
UTi20T
90.5
38
HTi05T
HTi10
92.5
92.0
91.5
TF15
Young's
Modulus
(GPa)
T.R.S
(GPa)*
5.5
520
2.0
79
79
4.5
4.6
600
630
1.5
2.0
71
5.3
580
2.5
1GPa = 102kg/mm2, 1W/mK=2.39 x 10-3cal/cm sec r
J009
CBN (SINTERED CBN)

a MB710 and MB730 for cast iron cutting.
a BC5030 for high-speed roughing of cast irons is now
available.
a BC5030 roughing grade in combination with the AOX body
allows use of up to 16 corners and enables cost-effective,

high performance machining.
SELECTION STANDARD / RECOMMENDED CUTTING CONDITIONS

a FINISHING
Work Material
Cutting Speed (SFM)
Structure
1640
820
2460
3280
4100
Feed Depth of Cut

Coolant
(inch/rev) (inch)
Ferritic + Pearilitic
.012
Gray Cast Iron
.020
Dry
Pearilitic
a ROUGHING
Work Material
Cutting Speed (SFM)
Structure
1640
820
Gray Cast Iron
3280
4920
6560
BC5030
Pearilitic
Feed Depth of Cut

Coolant
(inch/rev) (inch)
.006
.118
Dry
FEATURES AND BASE

Grade
Application
Features
MB710
For General Cutting
MB730
For High Speed Cutting

For Interrupted Cutting
BC5030
High-speed machining at large depths of cut

High-speed interrupted machining
at large depths of cut
General purpose grade with well balanced wear and fracture resistance.
Has the largest CBN content and therefore displays good thermal conductivity.
It is suitable for the high temperatures that are generated in high speed cutting.
High CBN content and high thermal conductivity. The whole insert is composed of
sintered CBN. This enables high speed, high efciency machining at larger depths of cut.
The coating is for recognition of spent corners.
Tool
AOX445R10008D
Insert
SL-ONEN120404ASN (BC5030)
Machine
Machining Center
Workpiece
Cutting Condition
AISI-35
Cutting Speed (SFM)
3940
Depth of Cut (inch)
.110
Width of Cut (inch)
2.76
Table Feed (inch/min)
120
Feed per Tooth (inch/tooth)

Result
J010
.004
10 times longer tool life and 4 times higher efciency
than ceramics.
Excellent machining with a surface nish of Ra < 64!m.
Main
Component Coating Layer
CBN
TiC
Al2O3
CBN (High Content)
Co Base Alloy
CBN
AIN

TiN Base
PCD (SINTERED DIAMOND)

a Suitable for non-ferrous metals cutting such as aluminum alloy.
a Suitable for extremely high speed nishing.
Micro-Structure of MD220
GRADE FEATURES
Grade
Features
MD220
Excellent in the balance between wear resistance and fracutre resistance.

A wide range of tooling application.
RECOMMENDED CUTTING CONDITION

Work Material
Cutting Speed (SFM)
Aluminum Alloy
(Si < 12%)
3280 19700
Depth of Cut (inch)
MD220
.012
.002
655 2630
Finished Surface Roughness (!inch)
CUTTING PERFORMANCE
Revolution : 6000min-1
Rz=.041!inch
Revolution : 20000min-1
Rz=.056!inch
Workpiece
Insert
Grade
Tool
Feed
Depth of Cut
Width of Cut
Dry Cutiing
: Aluminum Alloy
: NP-GDCW1240PDFR2
: MD220
: V10000R0406D
: .008inch/tooth
: .020inch
: 3.150inch
Aluminum Alloy
(Si > 13%)
Grade
Revolution Speed (min-1)
J011
MILLING INSERTS
P
M
K
N
S
H
Work Material
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
Dimensions (inch)
Class
Honing
FH7020
MC5020
VP15TF
VP30RT
TF15
Coated Carbide
L1
AHX640 ^K014
NNMU200608ZEN-HK
NNMU200608ZEN-HK
M E
.787
.258
.031
AHX640 ^K014
NNMU200608ZEN-MK
NNMU200608ZEN-MK
M E
.787
.258
.031
AHX640 ^K014
WNEU2006ZEN7C-WK WNEU2006ZEN7C-WK M E
.787
.258
.031
AJX ^K088
JOMW06T215ZZSR-FT JOMW06T215ZZSR-FT M S
Cutter Type
Order Number
(ISO) Number
Insert Geometry
F1
Re
a a
.250
.109
.047
.059
a a
.315
.125
.055
.079
JDMW09T320ZDSR-FT JDMW09T320ZDSR-FT M S
a a
.375
.156
.071
.079
120420ZDSR-FT
120420ZDSR-FT M S
a a
.472
.187
.098
.079
140520ZDSR-FT
140520ZDSR-FT M S
a a
.551
.219
.110
.079
JOMT06T215ZZSR-JM
JOMT06T215ZZSR-JM M S
a a
.250
.109
.047
.059
080320ZZSR-JM
080320ZZSR-JM M S
a a
.315
.125
.055
.079
JDMT09T320ZDSR-JM JDMT09T320ZDSR-JM M S
a a
.375
.156
.071
.079
a a
.472
.187
.098
.079
.551
.219
.110
.079
120420ZDSR-JM
120420ZDSR-JM M S
140520ZDSR-JM
140520ZDSR-JM M S
a a
JDMT120420ZDSR-ST
JDMT120420ZDSR-ST M S
a a
.472
.187
.098
.079
140520ZDSR-ST
140520ZDSR-ST M S
a a
.551
.219
.110
.079
JOMW... : 13, JDMW... : 15
AJX ^K088
APX3000 ^K030
J012
S1
*
AJX ^K088
D1
080320ZZSR-FT M S
080320ZZSR-FT
*JOMW... : 13, JDMW... : 15
L2
AOGT123602PEFR-GM AOGT123602PEFR-GM G F
.472
.260
.142
.071
.008
123604PEFR-GM
123604PEFR-GM G F
.472
.260
.142
.063
.016
123608PEFR-GM
123608PEFR-GM G F
.472
.260
.142
.047
.031
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round F : Sharp
Dimensions (inch)
(ISO) Number
APX3000 ^K030
APX3000 ^K030
APX4000 ^K038
APX4000 ^K038
AQX ^K080
L1
L2
S1
F1
Re
AOMT123604PEER-H
AOMT123604PEER-H
M E
a a a
.472
.260
.142
.063
.016
123608PEER-H
123608PEER-H
M E
a a a
.472
.260
.142
.047
.031
123616PEER-H
123616PEER-H
M E
a a a
.472
.260
.142
.016
.063
AOMT123602PEER-M
AOMT123602PEER-M
M E
a a
.472
.260
.142
.071
.008
123604PEER-M
123604PEER-M
M E
a a
.472
.260
.142
.063
.016
123608PEER-M
123608PEER-M
M E
a a
.472
.260
.142
.047
.031
123610PEER-M
123610PEER-M
M E
ss
.472
.260
.142
.039
.039
123612PEER-M
123612PEER-M
M E
a a
.472
.260
.142
.031
.047
123616PEER-M
123616PEER-M
M E
a a
.472
.260
.142
.016
.063
123620PEER-M
123620PEER-M
M E
a a
.472
.260
.142
.016
.079
123624PEER-M
123624PEER-M
M E
a a
.472
.260
.142
.016
.094
123630PEER-M
123630PEER-M
M E
a a
.472
.260
.142
.016
.118
123632PEER-M
123632PEER-M
M E
a a
.472
.260
.142
.016
.125
AOMT184804PEER-H
AOMT184804PEER-H
M E
a a a
.709
.354
.189
.071
.016
184808PEER-H
184808PEER-H
M E
a a a
.709
.354
.189
.055
.031
184816PEER-H
184816PEER-H
M E
a a a
.709
.354
.189
.016
.063
184832PEER-H
184832PEER-H
M E
.709
.354
.189
.016
.125
184840PEER-H
184840PEER-H
M E
.709
.354
.189
.016
.157
184850PEER-H
184850PEER-H
M E
.709
.354
.189
.197
184864PEER-H
184864PEER-H
M E
.709
.354
.189
.250
AOMT184804PEER-M
AOMT184804PEER-M
M E
a a
.709
.354
.189
.071
.016
184808PEER-M
184808PEER-M
M E
a a
.709
.354
.189
.055
.031
184810PEER-M
184810PEER-M
M E
.709
.354
.189
.039
.039
184812PEER-M
184812PEER-M
M E
.709
.354
.189
.031
.047
184816PEER-M
184816PEER-M
M E
a a
.709
.354
.189
.016
.063
184820PEER-M
M E
184820PEER-M
AQX ^K080
MC5020
VP15TF
VP20RT
VP30RT
HTi10
Order Number
Insert Geometry
Class
Cutter Type
Honing
Coated Carbide
QOGT0830R-G1
QOGT0830R-G1
G F
0934R-G1
0934R-G1
G F
1443R-G1
1443R-G1
G F
1651R-G1
1651R-G1
G F
1959R-G1
1959R-G1
QOMT0830R-M2
QOMT0830R-M2
M E
0934R-M2
0934R-M2
M E
1443R-M2
1443R-M2
M E
1651R-M2
1651R-M2
1959R-M2
1959R-M2
*
F
.709
.354
.189
.016
.079
.350
.220
.120
.016
.401
.264
.134
.016
.528
.350
.169
.016
.650
.433
.200
.016
.016
.768
.512
.232
.350
.220
.120
.031
.401
.264
.134
.031
.528
.350
.169
.031
M E
.650
.433
.200
.031
M E
.768
.512
.232
.031
Work Material
P
M
K
N
S
H
*1 Grade VP15TF has E honing.

J013
MILLING INSERTS
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round F : Sharp
(ISO) Number
QOGT0830R-G1
1035R-G1
QOGT0830R-G1
1035R-G1
1342R-G1
1342R-G1
1651R-G1
1651R-G1
1856R-G1
1856R-G1
2062R-G1
2576R-G1
2062R-G1
2576R-G1
QOMT0830R-M2
1035R-M2
QOMT0830R-M2
1035R-M2
M E
M E
1342R-M2
1342R-M2
M E
1651R-M2
1651R-M2
1856R-M2
1856R-M2
2062R-M2
2576R-M2
2062R-M2
2576R-M2
M E
ss
M E
ss
RDMW0517M0E
0620M0E
RDMW0517M0E
0620M0E
G E
G E
0724M0E
0724M0E
G E
ASX400 ^K022
SOET12T308PEER-JL
SOET12T308PEER-JL
E E
ASX400 ^K022
AQX (METRIC)
^K081
AQX (METRIC)
^K081
ARX (METRIC)
^K099
Dimensions (inch)
Cermet Carbide
F7010
F7030
MC5020
VP15TF
VP30RT
MP8010
NX4545
Order Number
Insert Geometry
Class
Cutter Type
Honing
Coated
HTi10
Work Material
P
M
K
N
S
H
L1
L2
D1
S1
G F
.350
.220
.120
.417
.276
.138
.516
.343
.165
.650
.433
.200
.709
.472
.220
.803
.535
.244
1.016
.677
.299
a a
.350
.220
.120
ss
.417
.276
.138
ss
.516
.343
.165
M E
a a
.650
.433
.200
M E
ss
.709
.472
.220
.803
.535
.244
1.016
.677
.299
.197
.067
.236
.078
.276
.094
1
*
F 1
*
F 1
*
F 1
*
F 1
*
F 1
*
F 1
*
a a
.500
.156
SOMT12T308PEER-JM SOMT12T308PEER-JM M E
12T308PEEL-JM
12T308PEEL-JM M E
a a a a a
.500
.156
.500
.156
SOMT12T308PEER-JH SOMT12T308PEER-JH M E
a a a a
.500
.156
ASX400 ^K022
*1 Grade VP15TF has E honing.
J014
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
T : Chamfer X : Round (Small)
Order Number
(ISO) Number
Insert Geometry
ASX400 ^K022
SOMT12T320PEER-FT SOMT12T320PEER-FT M E
ASX400 ^K022
SOGT12T308PEFR-JP SOGT12T308PEFR-JP G F
ASX400
^K022
WOEW12T308PEER8C WOEW12T308PEER8C E E
ASX445 ^K008
SEET13T3AGEN-JL
SEET13T3AGEN-JL
E E
a a
13T3AGXN-JL
13T3AGXN-JL
E X
12T308PETR8C
a a
12T308PETR8C E T
a a
ASX445 ^K008
SEMT13T3AGSN-JM SEMT13T3AGSN-JM M S
a a a a a
ASX445 ^K008
SEMT13T3AGSN-JH SEMT13T3AGSN-JH M S
a a a a
ASX445 ^K008
SEMT13T3AGSN-FT SEMT13T3AGSN-FT M S
Dimensions (inch)
Cermet Carbide
Class
Honing
F7010
F7030
MC5020
VP15TF
VP30RT
NX2525
NX4545
HTi05T
HTi10
Coated
Cutter Type
L1
L2
S1
Re
.156
.079
.156
.031
.492
.520
.156
.031
.492
.520
.156
.031
.156
.059
.156
.059
.156
.059
.156
.059
.156
.059
Work Material
P
M
K
N
S
H
J015
MILLING INSERTS
P
M
K
N
S
H
Work Material
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round F : Sharp T : Chamfer
Dimensions (inch)
(ISO) Number
ASX445 ^K008
SEGT13T3AGFN-JP
SEGT13T3AGFN-JP
G F
ASX445
^K008
WEEW13T3AGER8C
WEEW13T3AGER8C
E E
13T3AGTR8C
13T3AGTR8C
E T
AXD4000 ^K052
XDGX175004PDFR-GL XDGX175004PDFR-GL G F
Re
F1
L1
20
S1
30
.68
9
"
J016
AXD7000 ^K056
BAE500
a
a
L1
L2
S1
F1
Re
.156
.098
.649
.651
.156
.323
.059
.649
.651
.156
.323
.059
.901
.197
.067
.016
175008PDFR-GL
175008PDFR-GL G F
.901
.197
.051
.031
175012PDFR-GL
175012PDFR-GL G F
.901
.197
.035
.047
175016PDFR-GL
175016PDFR-GL G F
.866
.197
.055
.063
175020PDFR-GL
175020PDFR-GL G F
.866
.197
.039
.079
.094
175024PDFR-GL
175024PDFR-GL G F
.866
.197
.024
175030PDFR-GL
175030PDFR-GL G F
.831
.197
.031
.118
175032PDFR-GL
175032PDFR-GL G F
.831
.197
.024
.125
175040PDFR-GL
175040PDFR-GL G F
.787
.197
.031
.157
175050PDFR-GL
175050PDFR-GL G F
.764
.197
.016
.197
XDGX227008PDFR-GL XDGX227008PDFR-GL G F
a 1.181
.276
.079
.031
227016PDFR-GL
227016PDFR-GL G F
a 1.181
.276
.047
.063
227020PDFR-GL
227020PDFR-GL G F
a 1.181
.276
.031
.079
227024PDFR-GL
227024PDFR-GL G F
a 1.181
.276
.016
.094
227030PDFR-GL
227030PDFR-GL G F
a 1.134
.276
.031
.118
227032PDFR-GL
227032PDFR-GL G F
a 1.134
.276
.024
.125
227040PDFR-GL
227040PDFR-GL G F
a 1.083
.276
.035
.157
227050PDFR-GL
227050PDFR-GL G F
a 1.063
.276
.016
.197
.625
.375
.125
.016
.625
.375
.125
.016
.625
.375
.125
.031
.375
.125
.031
.375
.125
.063
.625
.375
.125
.094
.625
.375
.125
.125
.625
.375
.125
.252
AEMW150304ER
AEMW150304ER
M E
150304FR
150304FR
M F
150308ER
150308ER
M E
150308FR
150308FR
M F
.625
1503062ER
1503062ER
M E
.625
1503093ER
1503093ER
M E
1503125ER
1503125ER
M E
1503250ER
1503250ER
M E

a
r
UTi20T
HTi05T
HTi10
TF15
Order Number
Insert Geometry
Class
Honing
VP15TF
UP20M
LC15TF
NX2525

Cutter Type
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round F : Sharp
Dimensions (inch)
Class
Honing
F7010
F7030
VP15TF
UP20M
NX4545
UTi20T
HTi10
AEMW19T304ER
AEMW19T304ER
M E
as
19T304FR
19T304FR
M F
19T308ER
19T308ER
M E
19T308FR
19T308FR
M F
19T3062ER
19T3062ER
M E
.750
.500
.156
.063
19T3093ER
19T3093ER
M E
.750
.500
.156
.094
19T3125ER
19T3125ER
M E
.750
.500
.156
.125
.252
Cutter Type
Order Number
(ISO) Number
Insert Geometry
BAE600
19T3250ER
19T3250ER
M E
BAP300 ^K066
APGT1135PDFR-G2
BAP300 ^K066
APMT1135PDER-H1 APMT1135PDER-H1 M E
BAP300 ^K066
APGT1135PDFR-G2
L1
L2
S1
F1
Re
.750
.500
.156
.016
.750
.500
.156
.016
a a
.750
.500
.156
.031
.750
.500
.156
.031
G F
.750
.500
.156
.433
.250
.138
.047
.031
.433
.250
.138
.059
.016
a a a
.433
.250
.138
.047
.031
.433
.250
.138
.016
.063
.433
.250
.138
.016
.094
1135PDER-H2
1135PDER-H2 M E
1135PDER-H4
1135PDER-H4 M E
1135PDER-H6
1135PDER-H6 M E
APMT1135PDER-M0 APMT1135PDER-M0 M E
.433
.250
.138
.071
.008
1135PDER-M1
1135PDER-M1 M E
.433
.250
.138
.059
.016
1135PDER-M2
1135PDER-M2 M E
a a
.433
.250
.138
.047
.031
BAP400 ^K066
APGT1604PDFR-G2
APGT1604PDFR-G2 G F
.650
.375
.187
.055
.031
BAP400 ^K066
APMT1604PDER-H1
APMT1604PDER-H1
M E
.650
.375
.187
.067
.016
1604PDER-H2
1604PDER-H2
M E
a a a
a a
.650
.375
.187
.055
.031
1604PDER-H4
1604PDER-H4
M E
.650
.375
.187
.016
.063
1604PDER-H6
1604PDER-H6
M E
.650
.375
.187
.016
.094
1604PDER-H8
1604PDER-H8
M E
.650
.375
.187
.016
.125
Work Material
P
M
K
N
S
H
J017
MILLING INSERTS
Work Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round F : Sharp
S : Chamfer + Round T : Chamfer
Dimensions (inch)
Cutter Type
Order Number
(ISO) Number
BAP400 ^K066
APMT1604PDER-M2
APMT1604PDER-M2
M E
a a
BAP3500 ^K050
XPGT13T3PDER-G1
XPGT13T3PDER-G1
G E
13T3PDER-G2
13T3PDER-G2
13T3PDER-G6
13T3PDER-G6
L1
L2
D1
S1
F1
Re
.650
.375
.187
.055
.031
.512
.311
.156
.063
.016
G E
.512
.311
.156
.047
.031
G E
.512
.311
.156
.016
.094
13T3PDER-G75
13T3PDER-G75 G E
.512
.311
.156
.016
.118
13T3PDER-G8
13T3PDER-G8
G E
.512
.311
.156
.016
.125
XPGT13T3PDFR-G1
XPGT13T3PDFR-G1
G F
.512
.311
.156
.063
.016
13T3PDFR-G2
13T3PDFR-G2
G F
.512
.311
.156
.047
.031
13T3PDFR-G6
13T3PDFR-G6
G F
.512
.311
.156
.016
.094
13T3PDFR-G75
13T3PDFR-G75 G F
.512
.311
.156
.016
.118
13T3PDFR-G8
13T3PDFR-G8
G F
.512
.311
.156
.016
.125
XPMT13T3PDER-M1
XPMT13T3PDER-M1
M E
a a
.512
.311
.156
.063
.016
13T3PDER-M2
13T3PDER-M2
M E
a a
.512
.311
.156
.047
.031
13T3PDER-M6
13T3PDER-M6
M E
a a
.512
.311
.156
.016
.094
13T3PDER-M75
13T3PDER-M75 M E
a a
.512
.311
.156
.016
.118
13T3PDER-M8
13T3PDER-M8
a a
.512
.311
.156
.016
.125
Insert Geometry
BAP3500 ^K050
BAP3500 ^K050
BF407 ^K019
M E
SFAN42ZFFR2
SFAN1203ZFFR2
A F
.500
.125
.094
42ZFFL2
1203ZFFL2
A F
.500
.125
.094
SFCN42ZFFR2
SFCN1203ZFFR2
A F
.500
.125
.094
OEMX12T3ETR1
OEMX12T3ETR1
M T
.500
.156
.039
12T3ESR1
12T3ESR1
M S
.500
.156
.039
OEEX1705ETR1
OEEX1705ETR1
M T
ss
.669
.197
.055
OEMX1705ETR1
OEMX1705ETR1
M T
.669
.197
.055
1705ESR1
1705ESR1
M S
.669
.197
.055
BOE ^K108
BOE ^K108
J018
Class
Honing
F7010
F7030
VP15TF
NX2525
NX4545
HTi10
a
a
OEMX12T3ETR1-JS
OEMX12T3ETR1-JS M T
.507
.156
.039
12T3EER1-JS
12T3EER1-JS M E
.507
.156
.039
1705EER1-JS
1705EER1-JS M E
as
.669
.197
.055
1705ETR1-JS
1705ETR1-JS M T
.669
.197
.055

a
r
a
a
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round S : Chamfer + Round
T : Chamfer
L1
REMX12T3EN
REMX12T3EN
M E
.500
.164
12T3SN
12T3SN
M S
.500
.164
1705EN
1705EN
M E
.679
.205
1705SN
1705SN
M S
.679
.205
Cutter Type
Order Number
(ISO) Number
Insert Geometry
BOE ^K108
BOE ^K108
BRP ^K104
Dimensions (inch)
Carbide
Class
Honing
F7010
F7030
VP15TF
UP20M
AP20M
UTi20T
Coated
D1
S1
F1
Re
REMX12T3EN-JS
REMX12T3EN-JS
M E
.500
.164
1705EN-JS
1705EN-JS
M E
.679
.205
RPMT07T200E-JS
RPMT07T200E-JS
M E
a a
.313
.109
09T300E-JS
09T300E-JS
M E
.375
.156
120400E-JS
120400E-JS
M E
.500
.188
150600E-JS
150600E-JS
M E
a r a
.625
.250
a a
RPMW07T200E
RPMW07T200E
M E
a a
.313
.109
09T300E
09T300E
M E
a a
.375
.156
120400E
120400E
M E
.500
.188
150600E
150600E
M E
.625
.250
BSP ^K112
SPMB1204APT
SPMB1204APT
M T
.500
.187
.055
BXD4000 ^K062
XDGT1550PDER-G04
XDGT1550PDER-G04 G E
.886
.197
.059
.016
1550PDER-G08
1550PDER-G08 G E
.886
.197
.043
.031
1550PDER-G12
1550PDER-G12 G E
.886
.197
.028
.047
1550PDER-G16
1550PDER-G16 G E
.886
.197
.016
.063
1550PDER-G20
1550PDER-G20 G E
.854
.197
.008
.079
1550PDER-G30
1550PDER-G30 G E
.787
.197
.024
.118
1550PDER-G32
1550PDER-G32 G E
.787
.197
.016
.125
1550PDER-G40
1550PDER-G40 G E
.748
.197
.020
.157
1550PDER-G50
1550PDER-G50 G E
.709
.197
.016
.197
BRP ^K104
Work Material
P
M
K
N
S
H
J019
MILLING INSERTS
Work Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round F : Sharp
T : Chamfer
(ISO) Number
BXD4000 ^K062
BXD4000 ^K062
ECMP ^K113
FBP415 ^K018
Dimensions (inch)
L1
D1
S1
F1
Re
XDGT1550PDFR-G04
XDGT1550PDFR-G04 G F
.886
.197
.059
.016
1550PDFR-G08
1550PDFR-G08 G F
.886
.197
.043
.031
1550PDFR-G12
1550PDFR-G12 G F
s .886
.197
.028
.047
1550PDFR-G16
1550PDFR-G16 G F
.886
.197
.016
.063
1550PDFR-G20
1550PDFR-G20 G F
.854
.197
.008
.079
1550PDFR-G30
1550PDFR-G30 G F
.787
.197
.024
.118
1550PDFR-G32
1550PDFR-G32 G F
.787
.197
.016
.125
1550PDFR-G40
1550PDFR-G40 G F
.748
.197
.020
.157
1550PDFR-G50
1550PDFR-G50 G F
.709
.197
.016
.197
.886
.197
.059
.016
.886
.197
.043
.031
XDGT1550PDFR-GL04 XDGT1550PDFR-GL04 G F
1550PDFR-GL08
CFSP ^K114
Cermet Carbide
F7010
MC5020
VP15TF
LC15TF
UP20M
NX2525
NX4545
UTi20T
HTi10
TF15
Order Number
Insert Geometry
Class
Cutter Type
Honing
Coated
1550PDFR-GL08 G F
SPMW321
SPMW090304
M E 1
s ss ss
.375 .125
.016
322
090308
M E 1
s ss ss
.375 .125
.031
421
120304
a ss a a
.500 .125
.016
422
120308
a ss a a
.500 .125
.031
MPMM322
MPMT090308
M E
.375 .125
.031
432
120408
M E
.500 .1875
.031
r s
.500 .125
.055
.500 .125
.055
.500 .125
.055
SPEN42EEER1
SPEN1203EEER1
42EEEL1
1203EEEL1
*
*
E 1
*
E 1
*
E E
a a
E E
E E
FBP415 ^K018
SPER42EEER-JS
SPER1203EEER-JS
*1 Grade NX2525 and NX4545 have T honing.
J020

a
r
Work Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round
Dimensions (inch)
Class
Honing
F7030
MC5020
VP15TF
UP20M
NX2525
UTi20T
HTi05T
HTi10
SPNN42EEER1
SPNN1203EEER1
N E
42EEEL1
1203EEEL1
N E
WPC42EEER10C
WPC42EEER10C
C E
.500
.597
.125
.394
42EEEL10C
42EEEL10C
C E
.500
.597
.125
.394
Cutter Type
Order Number
(ISO) Number
Insert Geometry
FBP415 ^K018
L1
L2
D1
.500
.500
S1
F1
Re
.125
.055
.125
.055
FBP415 ^K018
CCMX083508ENA
CCMX083508EN-A
09T308ENA
09T308EN-A
LER ^K078
CCMX09T308ENB
LER ^K078
LER ^K078
LER ^K078
M E s
.313
.138
.031
a a
.375
.156
.031
CCMX09T308EN-B
M E s
.375
.156
.031
ZCMX083508ERA
ZCMX083508ER-A
M E s
09T308ERA
09T308ER-A
ZCMX09T308ERB
ZCMX09T308ER-B
M E
M E
M E s
.409
.313
.137
.031
a a s
.472
.375
.156
.031
.472
.375
.156
.031
J021
MILLING INSERTS
Work Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round F : Sharp
T : Chamfer
Dimensions (inch)
Cutter Type
Order Number
(ISO) Number
Insert Geometry
MBD ^K123
MBF ^K123
MBN ^K122
J022
NSE300 ^K028
For improved
wall accuracy
L1
D1
S1
F1
Re
MBD0500021
MBD0500021
.550
.500
.031
0500041
0500041
.550
.500
.063
0625021
0625021
.625
.625
.031
0625041
0625041
.625
.625
.063
0750021
0750021
.700
.750
.031
0750041
0750041
.700
.750
.063
1000021
1000021
.925
1.000
.031
1000041
1000041
.925
1.000
.063
1000081
1000081
.925
1.000
.125
MBF0500021
MBF0500021
.550
.500
.031
0500041
0500041
.550
.500
.063
0625021
0625021
.625
.625
.031
0625041
0625041
.625
.625
.063
0750021
0750021
.700
.750
.031
0750041
0750041
.700
.750
.063
1000021
1000021
.925
1.000
.031
1000041
1000041
.925
1.000
.063
1000081
1000081
.925
1.000
.125
MBN0312001
MBN0312001
.312
0375001
0375001
.375
0500001
0500001
.500
0625001
0625001
.625
0750001
0750001
.750
1000001
1000001
1.000
1250001
1250001
1.250
M200001
M200001
.787
M300001
M300001
1.181
TECN32PEFR1W
TECN1603PEFR1W
C F
.375
.125
.055
.016
32PEER1W
1603PEER1W C E
.375
.125
.055
.016
32PETR1W
1603PETR1W
.375
.125
.055
.016
Curved edge

a
r
Class
Honing
NX2525
NX4545
UTi20T
HTi10
APL05
Cermet Carbide
C T ss s
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
T : Chamfer Z : Strong
Cutter Type
Order Number
(ISO) Number
Insert Geometry
NSE300 ^K028
TEEN32PEFR1
TEEN1603PEFR1
E F
32PEER1
1603PEER1
E E
32PETR1
1603PETR1
E T
32PESR1
1603PESR1
E S
Dimensions (inch)
Cermet Carbide
Class
Honing
F7010
F7030
MC5020
VP15TF
UP20M
AP10H
NX2525
NX4545
UTi20T
HTi10
Coated
D1
S1
F1
Re
.375
.125
.055
.016
r a
.375
.125
.055
.016
.375
.125
.055
.016
.375
.125
.055
.016
.375
.125
.055
.016
sa a
a
a s
NSE300 ^K028
TEER32PEER-JS
TEER1603PEER-JS
E E
NSE400 ^K028
SE400
TECN43PEFR1
TECN2204PEFR1
C F
.500
.187
.055
.039
43PEER1
2204PEER1
C E
.500
.187
.055
.039
43PETR1
2204PETR1
C T
.500
.187
.055
.039
TEEN43PEFR1
TEEN2204PEFR1
E F
.500
.187
.055
.039
43PEER1
2204PEER1
E E
a a
a a
.500
.187
.055
.039
43PETR1
2204PETR1
E T
.500
.187
.055
.039
43PESR1
2204PESR1
E S
.500
.187
.055
.039
TEKN43PEER1
TEKN2204PEER1
K E
.500
.187
.076
43PESR1
2204PESR1
K S
.500
.187
.076
43PETR1
2204PETR1
K T
.500
.187
.076
43PETR
2204PETR
K T
.500
.187
.076
2204PEZR
K Z
.500
.187
.076
.500
.187
.055
.039
.313
.125
.079
.500
.219
.055
.031
.500
.219
.055
.047
43PEZR
NSE400 ^K028
SE400
TEER43PEER-JS
TEER2204PEER-JS
E E
PMF ^K138
TPEW1303ZPER2
TPEW1303ZPER2
E E
PMR ^K137
CPMT1205ZPEN-M2 CPMT1205ZPEN-M2 M E
1205ZPEN-M3
1205ZPEN-M3 M E
a a
ss s
a a a
a s
s
s
s
s
s
s
as
Work Material
P
M
K
N
S
H
J023
MILLING INSERTS
Work Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
Dimensions (inch)
Cutter Type
Order Number
(ISO) Number
SE400
WEC400PEER10C
WEC400PEER10C
C E
SE415
SECN42EFTR1
SECN1203EFTR1
C T
SEEN42EFFR1
SEEN1203EFFR1
E F
42EFER1
1203EFER1
E E
42EFTR1
1203EFTR1
E T
42EFSR1
1203EFSR1
E S
SEKN42EFSR1
SEKN1203EFSR1
K S
42EFTR1
1203EFTR1
K T
1203EFTR
K F
Insert Geometry
J024
Class
Honing
F7010
F7030
MC5020
VP15TF
NX2525
NX4545
UTi20T
HTi05T
HTi10
42EFTR
L1
L2
S1
F1
Re
.472
.688
.187
.393
.016
.125
.055
.039
.125
.055
.039
.125
.055
.039
.125
.055
.039
ss
.125
.055
.039
.125
.055
.125
.055
.125
.071
.039
.125
.055
.039
s
a
a
a a
s
s
SE415
SEER42EFER-JS
SEER1203EFER-JS
E E
SE415
WEC42EFFR5C
WEC42EFFR5C
C F
.500
.540
.125
.197
.039
42EFER5C
42EFER5C
C E
.500
.540
.125
.197
.039
42EFTR5C
42EFTR5C
C T
.500
.540
.125
.197
.039
.500
.590
.125
.394
.039
.125
.055
.039
.125
.055
.039
.125
.055
.039
.125
.094
.039
.125
.055
.039
a a a a
.125
.055
.039
a a
.125
.055
.039
.125
.055
.125
.055
.125
.067
.039
SE415
WEC42EFER10C
WEC42EFER10C
C E
SE445
SECN42AFTN1
SEEN42AFFN1
42AFEN1
42AFEN2
42AFTN1
42AFSN1
42AFXN1
SEKN42AFSN1
42AFTN1
42AFTN
SECN1203AFTN1
SEEN1203AFFN1
1203AFEN1
1203AFEN2
1203AFTN1
1203AFSN1
1203AFXN1
SEKN1203AFSN1
1203AFTN1
1203AFTN
C
E
E
E
E
E
E
K
K
K

a
r
T
F
E
E
T
S
X
S
T
T
as s
s
a
a
a
a r
a a a
s
s
s
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
Dimensions (inch)
Cutter Type
Order Number
(ISO) Number
SEER42AFEN-JS
SEER1203AFEN-JS
E E
42AFXN-JS
1203AFXN-JS
E X
Insert Geometry
SE445
SE445
Class
Honing
F7010
F7030
MC5020
VP15TF
NX2525
NX4545
UTi20T
HTi05T
HTi10
WEC42AFFR5C
WEC1203AFFR5C
C F
42AFER5C
1203AFER5C
C E
42AFTR5C
1203AFTR5C
C T
SE445
WEC42AFER10C
WEC42AFER10C
C E
SE515
SEEN53EFER1
53EFTR1
53EFSR1
SEEN1504EFER1
1504EFTR1
1504EFSR1
E E
E T
E S
SECN53AFTN1
SEEN53AFFN1
53AFEN1
53AFTN1
53AFSN1
53AFXN1
SEKN53AFSN1
53AFTN1
53AFTN
SEER53AFEN-JS
C T
SECN1504AFTN1
E F
SEEN1504AFFN1
E E
1504AFEN1
E T
1504AFTN1
E S
1504AFSN1
E X
1504AFXN1
K S
SEKN1504AFSN1
K T
1504AFTN1
K T
1504AFTN
SEER1504AFEN-JS E E
SE545
SE545
D1
S1
F1
Re
a a a a
.500
.125
.055
.039
.500
.125
.055
.039
.125
.197
.039
.125
.197
.039
.125
.197
.039
.125
.394
.039
.625
.187
.055
.039
.625
.187
.055
.039
.625
.187
.055
.039
.625
.187
.055
.039
.625
.187
.055
.039
.625
.187
.055
.039
.625
.187
.055
.039
.625
.187
.055
.039
.625
.187
.055
.039
.625
.187
.055
.625
.187
.055
.625
.187
.067
.039
.625
.187
.055
.039
s
a
s
a
a
a a
a a
s
s
s
as s
Work Material
P
M
K
N
S
H
J025
MILLING INSERTS
P
M
K
N
S
H
Work Material
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: General Cutting
: Stable Cutting
: Unstable Cutting
Honing :
E : Round S : Chamfer + Round
T : Chamfer
Dimensions (inch)
Order Number
(ISO) Number
Insert Geometry
R19.685"
Re 45
Re
.625"
SPX ^K070
C E
53AFTR5C
53AFTR5C
C T
D1
S1
F1
Re
.625
.729
.187
.197
.039
.625
.729
.187
.197
.039
.787
.187
.787
.187
S1
RGEN2004EN
RGEN2004M0EN
2004SN
2004M0SN
E S
JPMX140412-JM
JPMX140412-JM
M E
a a
.563
.500
.187
.047
190412-JM
190412-JM
M E
a a
.750
.500
.187
.047
E E s
s
JPMX140412-WH
JPMX140412-WH
M E
a a
.563
.500
.187
.047
190412-WH
190412-WH
M E
a a
.750
.500
.187
.047
SPX ^K070
MPMX120412-JM
MPMX120412-JM
M E
a a
.500
.187
.047
SPX ^K070
MPMX120412-WH
MPMX120412-WH
M E
a a
.500
.187
.047
SPX ^K070
SPMX120408-JM
SPMX120408-JM
M E
a a
.500
.187
.031
SPX ^K070
WEC53AFER5C
L2
20
F1
SG20
J026
WEC53AFER5C
L1
.729"
SE545
UTi20T
HTi05T
Cutter Type
Class
Honing
VP15TF
VP20RT
UP20M
NX2525

Work Material
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round F : Sharp
Dimensions (inch)
Class
Honing
VP15TF
VP20RT
MP8010
Coated
L1
L2
D1
S1
F1
Re
M E
.500
.187
.031
.335
.375
.102
.020
.1875
F a
.394
.500
.118
.020
.2500
F a
.472
.6225
.157
.039
.3125
0750
F a
.591
.750
.197
.039
.3750
1000
1000
F a
.728
1.000
.236
.039
.5000
1250
1250
F a
.925
1.250
.276
.039
.6250
.1969
Cutter Type
Order Number
(ISO) Number
SPX ^K070
SPMX120408-WH
SPMX120408-WH
SRF ^K115
SRFT0375
SRFT0375
F a
0500
0500
0625
0625
0750
F1
L1
Insert Geometry
D1
S1
F1
L1
SRF (METRIC)
^K115
D1
.335
.394
.102
.020
12
12
F s
.394
.472
.118
.020
.2362
16
16
F s
.472
.630
.157
.039
.3150
20
20
F s
.591
.787
.197
.039
.3937
25
25
F s
.728
.984
.236
.039
.4921
30
30
F s
.886
1.181
.276
.039
.5906
32
32
F s
.925
1.260
.276
.039
.6299
F s
.591
.787
.197
.079
.0197
20R10
20R10
F s
.591
.787
.197
.079
.0394
20R20
20R20
F s
.591
.787
.197
.079
.0787
20R30
20R30
F s
.591
.787
.197
.079
.1181
25R05
25R05
F s
.728
.984
.236
.098
.0197
Re
25R10
25R10
F s
.728
.984
.236
.098
.0394
25R20
25R20
F s
.728
.984
.236
.098
.0787
25R30
25R30
F s
.728
.984
.236
.098
.1181
30R05
30R05
F s
.886
1.181
.276
.118
.0197
30R10
30R10
F s
.886
1.181
.276
.118
.0394
30R20
30R20
F s
.886
1.181
.276
.118
.0787
30R30
30R30
F s
.886
1.181
.276
.118
.1181
L1
SRM2 ^K126
SUFT20R05
S1
1
SRFT10
SUFT20R05
SUF (METRIC)
^K117
SRFT10
F s
F1
ap
S1
a a
SRM212C
SRM212C
M E
.748
.385
.169
.375
216C
216C
M E
.945
.512
.216
.500
220C
220C
.638
.275
.625
M E
1.102
P
M
K
N
S
H
J027
MILLING INSERTS
Work Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round
Dimensions (inch)
Class
Honing
F7030
VP15TF
Coated
SRM212E
SRM212E
M E
.610
.315
.169
.375
216E
216E
M E
.807
.409
.216
.500
220E
220E
M E
.964
.520
.275
.625
Cutter Type
Order Number
(ISO) Number
Insert Geometry
SRM2 ^K126
SRM2 ^K126
SRM2 ^K126
SRM2 (METRIC)
^K128
SRM2 (METRIC)
^K128
SRM2 (METRIC)
^K128
SRM2 (METRIC)
^K128
J028
L2
S1
B3
SRM210C-M
SRM210C-M
M E
.630
.323
.138
.313
212C-M
212C-M
M E
.748
.385
.169
.375
216C-M
216C-M
M E
.945
.512
.216
.500
220C-M
220C-M
M E
1.102
.638
.275
.625
SRM210E-M
SRM210E-M
M E
.531
.258
.138
.313
212E-M
212E-M
M E
.610
.315
.169
.375
216E-M
216E-M
M E
.807
.409
.216
.500
220E-M
220E-M
M E
.964
.520
.275
.625
SRG16C
SRG16C
G E
.630
.323
.138
.315
11
20C
20C
G E s
.748
.402
.181
.394
10
25C
25C
G E s
.945
.504
.217
.492
10
30C
30C
G E s
1.102
.602
.276
.591
10
32C
32C
G E s
1.102
.642
.276
.630
10
SRG16E
SRG16E
G E
.531
.264
.138
.315
11
20E
20E
G E s
.610
.335
.181
.394
25E
25E
G E s
.807
.402
.217
.492
30E
30E
G E s
.992
.480
.276
.591
32E
32E
G E s
1.028
.516
.276
.630
SRM16C-M
SRM16C-M
M E
.630
.323
.138
.315
11
20C-M
20C-M
M E
.748
.402
.181
.394
10
25C-M
25C-M
M E
.945
.504
.217
.492
10
30C-M
30C-M
M E
1.102
.602
.276
.591
10
32C-M
32C-M
M E
1.102
.642
.276
.630
10
SRM16E-M
SRM16E-M
M E
.531
.264
.138
.315
11
20E-M
20E-M
M E
.610
.335
.181
.394
25E-M
25E-M
M E
.807
.402
.217
.492
30E-M
30E-M
M E
.992
.480
.276
.591
32E-M
32E-M
M E
1.028
.516
.276
.630

a
r
L1
P
M
K
N
S
H
Work Material
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round
Cutter Type
Order Number
(ISO) Number
Insert Geometry
SRM2 40/50 (METRIC)

^K132
SRG40C
SRG40C
50C
50C
SRG40E
50E
Dimensions (inch)
Carbide
Class
Honing
VP15TF
VP20RT
VP30RT
UP20M
AP20M
UTi20T
Coated
L1
L2
S1
G E sss
1.417
.807
.315
.787
G E
sss
1.575
1.024
.335
.984
SRG40E
G E sss
1.260
.654
.315
.787
50E
G E sss
1.409
.787
.335
.984
11
SRM2 40/50 (METRIC)

^K132
TBE1
15
UDK15
UDK15
K E
.547
.453
.118
.295
20
20
K E
.638
.551
.157
.394
25
25
K E
.795
.669
.197
.492
30
30
K E
.917
.787
.236
.591
TBE2500W
UDK50AC
UDK50AC
K E
.756
.591
.236
.984
TBE2500W
UDK50AE
UDK50AE
K E
.803
.591
.236
.984
TBE2
SPMM432A
SPMT120408-A
M E
.187
TRM4 ^K134
UPM40
UPM40
M E
.520
.189
.787
50
50
M E
.650
.236
.984
11
J029
MILLING INSERTS
Work Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
(ISO) Number
Dimensions (inch)
Cermet Carbide
F7010
F7030
MC5020
VP15TF
UP20M
AP20M
MP9030
NX2525
NX4545
UTi20T
HTi10
Order Number
Insert Geometry
Class
Cutter Type
Honing
Coated
L1
D1
S1
F1
TRM4 ^K134
UPM50P0
UPM50P0
M E
.650
.236
.984
TRM4 ^K134
UPM40P1
UPM40P1
M E
.520
.189
.787
50P1
50P1
M E
.650
.236
.984
.752
.335
.500
.248
.375
.125
.047
.375
.125
.047
.500
.187
.055
.500
.187
.055
XNMU190912R-MS
XNMU190912R-MS
M E
VOX400 ^K020
SONX1206PER
SONX1206PER
N E
Corner Angle 0
11 Positive
TPKN32PPR
TPKN1603PPR
K T
32PPL
1603PPL
K T
43PDR
2204PDR
K T
43PDL
2204PDL
SPKN42EDR
SPKN1203EDR
K T
a a
.500
.125
.055
53EDR
1504EDR
K T
ss aa
.625
.187
.055
63EDR
1904EDR
.750
.187
.055
SDEN42AEN
SDEN1203AEN
E T
.500
.125
.047
SDKN42AEN
SDKN1203AEN
K T
.500
.125
.047
.500
.125
.047
.625
.187
.047
.374"
VFX6 ^K076
.500"
.047"
*1 a a
sa
a a
*
T
a a a a
r
a a a a
Corner Angle 15
11 Positive
Corner Angle 45
15 Positive
s
s
42AETN
1203AETN
K T
53AETN
1504AETN
K T

a
r
*22 aa a a sa aa
*
a
T
F7010 and F7020 have E honing.

*12 Grade
Grade HTi10 has F honing.
*
J030
Work Material
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
Dimensions (inch)
F7010
F7030
MC5020
VP15TF
NX2525
NX4545
UTi20T
HTi10
Honing
Cutter Type
Class

Order Number
(ISO) Number
Corner Angle 45
20 Positive
SEER43AFEN-JS
SEER1204AFEN-JS
E E
Corner Angle 45
20 Positive
SEMN43AZEN
SEMN1204AZEN
M E
Corner Angle 45
20 Positive
SEKN42AGTN
SEKN1203AGTN
K T
Negative
SNMN432
SNMN120408
M E
433
120412
M E
11 Positive
Re
Insert Geometry
D1
S1
F1
Re
.500
.187
.055
.039
.500
.187
.079
.008
.500
.125
.067
.039
ss
.500
.187
.031
ss
.500
.187
.047
SPMN422-CH
SPMN120308-CH10 M T
.500
.125
.031
423-CH
120312-CH10 M T
.500
.125
.047
633-CH
190412-CH15 M T
.750
.187
.047
634-CH
190416-CH15 M T
.750
.187
.063
25
11
S1
D1
SPMN4... : C=.004"
SPMN6... : C=.006"
SPMN421
11 Positive
Re
11
D1
S1
SPMN120304
M E
421T
120304T
M T
422
120308
M E
423
120312
M E
432
120408
M E
433
120412
M E
532
150408
M E
*1
*
ss
s
.500
.125
.016
a a
.500
.125
.031
ss
.500
.125
.047
ss
.500
.187
.031
a a
.500
.187
.047
P
M
K
N
S
H
*1 Grade HTi10 has F honing.
J031
MILLING INSERTS
P
M
K
N
S
H
Work Material
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Hardened Materials
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
Dimensions (inch)
11 Positive
Re
11
D1
S1
TPMN321
TPMN160304
322
160308
323
160312
431
220404
432
220408
433
220412
UTi20T
HTi10
L1
L2
D1
S1
Re
a s
a a
.375
.125
.016
s as
a a
.375
.125
.031
sa
.375
.125
.047
a a
as
.500
.187
.031
M E 2 s
*
E 2
*
E 1
*
E 1
*
E 1
*
E 1
*
NX2525
(ISO) Number
F7030
VP15TF
UP20M
Order Number
Insert Geometry
Honing
Cutter Type
Class
s as
ss
a a
APMT1604PDER
APMT1604PDER
M E
JPMT060204-E
JPMT060204-E
M E
ss
.500
.187
.047
.672
.375
.187
.031
.313
.256
.098
.016
L2
Re
11
S1
L1
85
D1
Re
11
Re
L2
86
S1
HTi10 has F honing.

*12 Grade
Grade HTi10 has F honing, grade NX2525 has T honing.
*
J032

a
r
Memo
J033
CBN AND PCD

Cutter Type
Order Number
(ISO) Number
Insert Geometry
AOX445 ^K017
D1
Re
Dimensions (inch)
PCD
Class
MB710
MB730
MB835
BC5030
MD220
CBN
D1
S1
F1
Re
.500
.187
.016
.500
.125
.094
SL-ONEN120404ASN
SL-ONEN120404ASN
SFCN42ZFFR2
SFCN1203ZFFR2
OEMX12T3ETR1
OEMX12T3ETR1
a a
.500
.156
.039
12T3ETR5
12T3ETR5
a a
.500
.156
.197
S1
BF407 ^K019
.118"
F1
D1
25
S1
BOE ^K108
20
F1
D1
S1
FBP415 ^K018
SPEN42EETR1
SPEN1203EETR1
E s
.500
.125
.055
TPEW1303ZPTR2
TPEW1303ZPTR2
.313
.125
.079
SECN42AFFR1
SECN1203AFFR1
.500
.125
.055
.039
.118"
11
F1
S1
D1
PMF ^K138
F1
60
J034
20
S1
D1
SE445
Re
D1 Re F1
20
S1

CBN AND PCD WITH WIPER

Dimensions (inch)
Order Number
(ISO) Number
Insert Geometry
NP-WEEW13T3AGFR3C
NP-WEEW13T3AGFR3C
13T3AGTR3C
13T3AGTR3C
L1
L2
D1
S1
F1
Re
.649
.651
.156
.130
.059
.649
.651
.156
.130
.059
L2
ASX445 ^K008
MD220
Cutter Type
Class
MB710
CBN PCD
29
F1
Re
S1
L1
BF407 ^K019
F1
NP-WFC42ZFER6
D1
NP-WFC42ZFER2
NP-WFC42ZFER2
.500
.125
.094
42ZFER6
42ZFER6
.500
.125
.236
.500
.125
.094
.500
.597
.125
.394
.500
.604
.125
.197
.039
.500
.604
.125
.197
.039
25
S1
F1
BF407 ^K019
WFC42ZFER2
WFC42ZFER2
WPC42EETR10C
WPC42EETR10C
WEC42AFFR5C
WEC42AFFR5C
42AFTR5C
42AFTR5C
D1
25
S1
F1
L2
R19.685"
FBP415 ^K018
15
11
F1
L1
S1
SE445
45
L1
F1
Re
20
S1
Re
L2
R15.748"
a
a
J035
CLASSIFICATION
Order Number
(ISO) Number
AEMW150304ER
AEMW150304ER
150304FR
Cutter Type
Page
Order Number
(ISO) Number
APMT1135PDER-H1
APMT1135PDER-H1
150304FR
1135PDER-H2
1135PDER-H2
150308ER
150308ER
1135PDER-H4
1135PDER-H4
150308FR
150308FR
1135PDER-H6
1135PDER-H6
1503062ER
1503062ER
APMT1135PDER-M0
APMT1135PDER-M0
1503093ER
1503093ER
1135PDER-M1
1135PDER-M1
1503125ER
1503125ER
1135PDER-M2
1135PDER-M2
APGT1604PDFR-G2
APGT1604PDFR-G2
1503250ER
BAE500
J016
Page
BAP300
^K066
J017
J017
1503250ER
AEMW19T304ER
AEMW19T304ER
19T304FR
19T304FR
19T308ER
19T308ER
19T308FR
19T308FR
19T3062ER
19T3062ER
APMT1604PDER-H1
APMT1604PDER-H1
19T3093ER
19T3093ER
1604PDER-H2
1604PDER-H2
19T3125ER
19T3125ER
1604PDER-H4
1604PDER-H4
19T3250ER
19T3250ER
1604PDER-H6
1604PDER-H6
1604PDER-H8
1604PDER-H8
APMT1604PDER-M2
APMT1604PDER-M2
BAE600
BAP400
^K066
J017
J017
AOGT123602PEFR-GM AOGT123602PEFR-GM APX3000

123604PEFR-GM
123604PEFR-GM ^K030
123608PEFR-GM
Cutter Type
123608PEFR-GM
J012
J017
J018
AOMT123604PEER-H AOMT123604PEER-H
123608PEER-H
123608PEER-H
123616PEER-H
123616PEER-H
J013
APMT1604PDER
APMT1604PDER
J032
123604PEER-M
123604PEER-M
CCMX083508ENA
CCMX083508EN-A
123608PEER-M
123608PEER-M
09T308ENA
09T308EN-A
123610PEER-M
123610PEER-M
123612PEER-M
123612PEER-M
123616PEER-M
123616PEER-M
CCMX09T308ENB
CCMX09T308EN-B
123620PEER-M
123620PEER-M
123624PEER-M
123624PEER-M
123630PEER-M
123630PEER-M
123632PEER-M
123632PEER-M
J013
184816PEER-H
184832PEER-H
184832PEER-H
184840PEER-H
184840PEER-H
184850PEER-H
184850PEER-H
184864PEER-H
184864PEER-H
J013
184808PEER-M
184810PEER-M
184810PEER-M
184812PEER-M
184812PEER-M
184816PEER-M
184816PEER-M
184820PEER-M
APGT1135PDFR-G2
1205ZPEN-M3
PMR
^K137
J023
JOMW06T215ZZSR-FT JOMW06T215ZZSR-FT AJX
080320ZZSR-FT ^K088
120420ZDSR-FT
120420ZDSR-FT
140520ZDSR-FT
140520ZDSR-FT
J012
JOMT06T215ZZSR-JM JOMT06T215ZZSR-JM
J013
080320ZZSR-JM
080320ZZSR-JM
JDMT09T320ZDSR-JM JDMT09T320ZDSR-JM
120420ZDSR-JM
120420ZDSR-JM
140520ZDSR-JM
140520ZDSR-JM
J012
JDMT120420ZDSR-ST JDMT120420ZDSR-ST
BAP300
^K066
J017
J036
CPMT1205ZPEN-M2
1205ZPEN-M3
JDMW09T320ZDSR-FT JDMW09T320ZDSR-FT
184820PEER-M
APGT1135PDFR-G2
CPMT1205ZPEN-M2
080320ZZSR-FT
184808PEER-M
J021
J021
AOMT184804PEER-H AOMT184804PEER-H APX4000

184808PEER-H
184808PEER-H ^K038
184816PEER-H
LER
^K078
140520ZDSR-ST
140520ZDSR-ST
J012
(ISO) Number
Cutter Type
Page
JPMT060204-E
Order Number
(ISO) Number
MPMX120412-JM
MPMX120412-JM
Cutter Type
J032
JPMX140412-JM
JPMX140412-JM
190412-JM
190412-JM
J026
MPMX120412-WH
SPX
^K070
MPMX120412-WH
J026
JPMX140412-WH
JPMX140412-WH
190412-WH
190412-WH
J026
NNMU200608ZEN-HK NNMU200608ZEN-HK AHX640W

200608ZEN-MK
200608ZEN-MK
^K014
J026
J012
NP-WEEW13T3AGFR3C NP-WEEW13T3AGFR3C ASX445
MBD0500021
MBD0500021
0500041
0500041
0625021
0625021
0625041
0625041
0750021
0750021
0750041
0750041
NP-WFC42ZFER2
NP-WFC42ZFER2
1000021
1000021
42ZFER6
42ZFER6
1000041
1000041
1000081
1000081
MBF0500021
MBF0500021
0500041
0500041
OEMX12T3ETR1
OEMX12T3ETR1
0625021
0625021
12T3ESR1
12T3ESR1
0625041
0625041
OEEX1705ETR1
OEEX1705ETR1
0750021
0750021
OEMX1705ETR1
OEMX1705ETR1
0750041
0750041
1000021
1000021
OEMX12T3ETR1-JS
OEMX12T3ETR1-JS
1000041
1000041
12T3EER1-JS
12T3EER1-JS
1000081
1000081
1705EER1-JS
1705EER1-JS
MBN0312001
MBN0312001
0375001
0375001
0500001
0500001
0625001
0625001
0750001
0750001
1000001
1000001
1250001
1250001
QOGT0830R-G1
QOGT0830R-G1
M200001
M200001
0934R-G1
0934R-G1
1443R-G1
1443R-G1
1651R-G1
1651R-G1
M300001
MBD
^K123
13T3AGTR3C
MPMT090308
432
120408
13T3AGTR3C
^K008
J035
J022
BF407
^K019
J035
MBF
^K123
J022
1705ESR1
1705ETR1-JS
MBN
^K122
BOE
^K108
J018
1705ESR1
J018
1705ETR1-JS
OEMX12T3ETR1
OEMX12T3ETR1
12T3ETR5
12T3ETR5
J034
J022
M300001
MPMM322
Page
SPX
^K070
ECMP
^K113
J020
1959R-G1
1959R-G1
QOMT0830R-M2
QOMT0830R-M2
0934R-M2
0934R-M2
1443R-M2
1443R-M2
1651R-M2
1651R-M2
1959R-M2
1959R-M2
Order Number
JPMT060204-E
AQX
^K080
J013
J013
J037
CLASSIFICATION
Order Number
(ISO) Number
Cutter Type
Page
AQX(METRIC)
^K081
Order Number
(ISO) Number
QOGT0830R-G1
QOGT0830R-G1
1035R-G1
1035R-G1
1342R-G1
1651R-G1
1856R-G1
1856R-G1
42EFSR1
1203EFSR1
2062R-G1
2062R-G1
SEKN42EFSR1
SEKN1203EFSR1
42EFTR1
1203EFTR1
42EFTR
1203EFTR
SECN42EFTR1
SECN1203EFTR1
SEEN42EFFR1
SEEN1203EFFR1
1342R-G1
42EFER1
1203EFER1
1651R-G1
42EFTR1
1203EFTR1
J014
2576R-G1
2576R-G1
QOMT0830R-M2
QOMT0830R-M2
1035R-M2
1035R-M2
1342R-M2
1342R-M2
1651R-M2
1651R-M2
1856R-M2
1856R-M2
2062R-M2
2062R-M2
SECN42AFTN1
SECN1203AFTN1
2576R-M2
2576R-M2
SEEN42AFFN1
SEEN1203AFFN1
RDMW0517M0E
RDMW0517M0E
0620M0E
0620M0E
0724M0E
0724M0E
REMX12T3EN
REMX12T3EN
12T3SN
12T3SN
1705EN
1705EN
1705SN
1705SN
SEER42EFER-JS
ARX(METRIC)
^K099
J014
BOE
^K108
J019
42AFEN1
1203AFEN1
42AFEN2
1203AFEN2
42AFTN1
1203AFTN1
42AFSN1
1203AFSN1
42AFXN1
1203AFXN1
SEKN42AFSN1
SEKN1203AFSN1
42AFTN1
1203AFTN1
42AFTN
1203AFTN
SEER42AFEN-JS
SEER1203AFEN-JS
1705EN-JS
42AFXN-JS
1203AFXN-JS
2004M0SN
RPMT07T200E-JS
RPMT07T200E-JS
09T300E-JS
09T300E-JS
120400E-JS
120400E-JS
150600E-JS
J019
SECN42AFFR1
SG20
SECN1203AFFR1
SE445
J024
J025
SE445
BRP
^K104
J019
J034
SEEN53EFER1
SEEN1504EFER1
53EFTR1
1504EFTR1
53EFSR1
1504EFSR1
SE515
J025
150600E-JS
RPMW07T200E
SECN53AFTN1
SECN1504AFTN1
09T300E
09T300E
SEEN53AFFN1
SEEN1504AFFN1
120400E
120400E
53AFEN1
1504AFEN1
150600E
150600E
53AFTN1
1504AFTN1
53AFSN1
1504AFSN1
53AFXN1
1504AFXN1
SEKN53AFSN1
SEKN1504AFSN1
53AFTN1
1504AFTN1
53AFTN
1504AFTN
SDEN42AEN
SDEN1203AEN
SDKN42AEN
SDKN1203AEN
SDKN53AETN
J024
J026
RPMW07T200E
42AETN
J024
J024
REMX12T3EN-JS
RGEN2004M0EN
SE415
J014
1705EN-JS
2004SN
Page
SEER1203EFER-JS
REMX12T3EN-JS
RGEN2004EN
Cutter Type
J019
Corner Angle 45
15 Positive
J030
1203AETN
SDKN1504AETN
Corner Angle 45
15 Positive
J030
SEER53AFEN-JS
SE545
J025
SEER1504AFEN-JS
J025
J038
(ISO) Number
SEET13T3AGEN-JL
13T3AGXN-JL
13T3AGXN-JL
SEMT13T3AGSN-JM
Cutter Type
Page
ASX445
^K008
(ISO) Number
Cutter Type
J014
SEMT13T3AGSN-JM
SOMT12T308PEER-JM SOMT12T308PEER-JM
12T308PEEL-JM
12T308PEEL-JM
J014
SOMT12T308PEER-JH SOMT12T308PEER-JH
SEMT13T3AGSN-JH
J014
J015
SEMT13T3AGSN-FT
SOMT12T320PEER-FT SOMT12T320PEER-FT
SEMT13T3AGSN-FT
J015
J015
SEGT13T3AGFN-JP
SOGT12T308PEFR-JP SOGT12T308PEFR-JP
SEGT13T3AGFN-JP
J015
J015
SEER43AFEN-JS
SEER1204AFEN-JS
SONX1206PER
Corner Angle 45
20 Positive
SONX1206PER
VOX400
^K020
J031
SEMN43AZEN
SEMN1204AZEN
Corner Angle 45
20 Positive
J031
SEKN42AGTN
SEKN1203AGTN
Page
^K022
J015
J015
SEMT13T3AGSN-JH
Order Number
SOET12T308PEER-JL SOET12T308PEER-JL ASX400
J030
SPEN42EEER1
SPEN1203EEER1
42EEEL1
1203EEEL1
SPNN42EEER1
SPNN1203EEER1
42EEEL1
Corner Angle 45
20 Positive
J031
SPER42EEER-JS
FBP415
^K018
J020
1203EEEL1
SPER1203EEER-JS
FBP415
^K018
J020
SFAN42ZFFR2
SFAN1203ZFFR2
42ZFFL2
1203ZFFL2
SFCN42ZFFR2
SFCN1203ZFFR2
SFCN42ZFFR2
SFCN1203ZFFR2
BF407
^K019
J018
SPEN42EETR1
SPEN1203EETR1
J034
J034
SPKN42EDR
SPKN1203EDR
53EDR
1504EDR
63EDR
1904EDR
Corner Angle 15
11 Positive
J030
Order Number
SEET13T3AGEN-JL
SL-ONEN120404ASN SL-ONEN120404ASN AOX445

^K017
J034
SPMB1204APT
SPMB1204APT
BSP
^K112
J019
SNMN432
SNMN120408
433
120412
Negative
J031
SPMM432A
SPMT120408-A
TBE
J029
J039
CLASSIFICATION
Order Number
(ISO) Number
SPMN422-CH
SPMN120308-CH10
423-CH
120312-CH10
633-CH
190412-CH15
634-CH
190416-CH15
SPMN421
SPMN120304
421T
120304T
422
120308
423
120312
432
120408
433
120412
532
150408
SPMW321
SPMW090304
322
090308
421
120304
422
SPMX120408-JM
Cutter Type
Page
11 Positive
J031
11 Positive
J031
CFSP
^K114
J020
SPX
^K070
J026
SPMX120408-WH
SPMX120408-WH
J027
SRFT0375
SRFT0375
0500
0500
0625
0625
0750
0750
1000
1000
1250
J040
SRF
^K115
J027
1250
SRFT10
SRFT10
12
12
16
16
20
20
25
30
SRF(METRIC)
^K117
(ISO) Number
SRG16C
20C
20C
25C
25C
30C
30C
32C
32C
SRG16E
SRG16E
20E
20E
25E
25E
30E
30E
32E
120308
SPMX120408-JM
Order Number
SRG16C
SRM212C
216C
216C
220C
220C
SRM212E
SRM212E
216E
216E
220E
220E
SRM210C-M
SRM210C-M
212C-M
212C-M
216C-M
216C-M
220C-M
220C-M
SRM210E-M
SRM210E-M
212E-M
212E-M
216E-M
216E-M
SRM16C-M
20C-M
20C-M
25C-M
25C-M
30C-M
30C-M
32C-M
32C-M
SRM16E-M
20E-M
20E-M
25
25E-M
25E-M
30
30E-M
30E-M
32
32
SRG40C
SRG40C
50C
50C
32E-M
SRM2 40/50
^K132
J029
J028
SRM2
^K126
J027
J028
J028
J028
SRM2(METRIC)
^K128
J028
J028
32E-M
SUFT20R05
SUFT20R05
20R10
20R10
20R20
20R20
20R30
20R30
SRG40E
SRG40E
25R05
25R05
50E
50E
25R10
25R10
25R20
25R20
25R30
25R30
30R05
30R05
30R10
30R10
30R20
30R20
30R30
30R30
J029
J028
220E-M
SRM16C-M
SRM16E-M
J027
Page
SRM2(METRIC)
^K128
32E
SRM212C
220E-M
Cutter Type
SRF
^K115
J027
(ISO) Number
TECN1603PEFR1W
32PEER1W
1603PEER1W
32PETR1W
1603PETR1W
TEEN32PEFR1
TEEN1603PEFR1
32PEER1
1603PEER1
32PETR1
1603PETR1
32PESR1
TEER32PEER-JS
Cutter Type
Page
NSE300
^K028
UDK50AE
J029
1603PESR1
TEER1603PEER-JS
TECN2204PEFR1
2204PEER1
NSE400
^K028
43PETR1
2204PETR1
SE400
TEEN43PEFR1
TEEN2204PEFR1
43PEER1
2204PEER1
43PETR1
2204PETR1
43PESR1
2204PESR1
TEKN43PEER1
TEKN2204PEER1
43PESR1
2204PESR1
43PETR1
2204PETR1
43PETR
2204PETR
UPM40
UPM40
50
50
UPM50P0
TRM4
^K134
J029
UPM50P0
J030
J023
UPM40P1
UPM40P1
50P1
50P1
WEC400PEER10C
WEC400PEER10C
J030
SE400
J024
2204PEZR
TEER2204PEER-JS
J023
TPEW1303ZPER2
WEC42EFFR5C
WEC42EFFR5C
42EFER5C
42EFER5C
42EFTR5C
42EFTR5C
WEC42EFER10C
PMF
^K138
SE415
J024
WEC42EFER10C
J024
J023
TPEW1303ZPTR2
TPEW1303ZPTR2
PMF
^K138
J034
TPKN32PPR
TPKN1603PPR
32PPL
1603PPL
43PDR
2204PDR
43PDL
Page
TBE2500W
J023
43PEER1
TPEW1303ZPER2
Cutter Type
J029
UDK50AE
NSE300
^K028
TECN43PEFR1
43PEZR
(ISO) Number
UDK50AC
J022
J023
TEER43PEER-JS
Order Number
UDK50AC
WEC42AFFR5C
WEC1203AFFR5C
42AFER5C
1203AFER5C
42AFTR5C
1203AFTR5C
WEC42AFER10C
Corner Angle 0
11 Positive
SE445
J025
WEC42AFER10C
J025
J030
Order Number
TECN32PEFR1W
2204PDL
WEC42AFFR5C
WEC42AFFR5C
42AFTR5C
42AFTR5C
220408
WEC53AFER5C
WEC53AFER5C
220412
53AFTR5C
53AFTR5C
TPMN321
TPMN160304
322
160308
323
160312
431
220404
432
433
UDK15
UDK15
20
20
25
25
30
30
11 Positive
J035
J032
TBE1
SE545
J026
J029
J041
CLASSIFICATION
Order Number
(ISO) Number
WEEW13T3AGER8C
WEEW13T3AGER8C
13T3AGTR8C
13T3AGTR8C
WFC42ZFER2
WFC42ZFER2
Cutter Type
Page
ASX445
^K008
J016
BF407
^K019
J035
WNEU2006ZEN7C-WK WNEU2006ZEN7C-WK AHX640W

^K014
J012
WOEW12T308PEER8C WOEW12T308PEER8C ASX400

12T308PETR8C
12T308PETR8C ^K022
WPC42EEER10C
WPC42EEER10C
42EEEL10C
42EEEL10C
WPC42EETR10C
WPC42EETR10C
J015
FBP415
^K018
J021
175012PDFR-GL
175012PDFR-GL
175016PDFR-GL
175016PDFR-GL
175020PDFR-GL
175020PDFR-GL
175024PDFR-GL
175024PDFR-GL
175030PDFR-GL
175030PDFR-GL
175032PDFR-GL
175032PDFR-GL
175040PDFR-GL
175040PDFR-GL
175050PDFR-GL
175050PDFR-GL
227020PDFR-GL
227020PDFR-GL
227024PDFR-GL
227024PDFR-GL
227030PDFR-GL
227030PDFR-GL
227032PDFR-GL
227032PDFR-GL
227040PDFR-GL
227040PDFR-GL
227050PDFR-GL
XNMU190912R-MS
J016
J016
227050PDFR-GL
XNMU190912R-MS
XPGT13T3PDER-G1
XPGT13T3PDER-G1
13T3PDER-G2
13T3PDER-G2
13T3PDER-G6
13T3PDER-G6
13T3PDER-G75
13T3PDER-G75
13T3PDER-G8
13T3PDER-G8
XPGT13T3PDFR-G1
XPGT13T3PDFR-G1
13T3PDFR-G2
13T3PDFR-G2
1550PDER-G12
1550PDER-G16
1550PDER-G16
1550PDER-G20
1550PDER-G20
1550PDER-G30
1550PDER-G30
13T3PDFR-G6
13T3PDFR-G6
1550PDER-G32
1550PDER-G32
13T3PDFR-G75
13T3PDFR-G75
1550PDER-G40
1550PDER-G40
13T3PDFR-G8
13T3PDFR-G8
1550PDER-G50
1550PDER-G50
XPMT13T3PDER-M1
XPMT13T3PDER-M1
XDGT1550PDFR-G04 XDGT1550PDFR-G04
J019
13T3PDER-M2
13T3PDER-M2
1550PDFR-G08
1550PDFR-G08
13T3PDER-M6
13T3PDER-M6
1550PDFR-G12
1550PDFR-G12
13T3PDER-M75
13T3PDER-M75
1550PDFR-G16
1550PDFR-G16
1550PDFR-G20
1550PDFR-G20
1550PDFR-G30
1550PDFR-G30
1550PDFR-G32
1550PDFR-G32
1550PDFR-G40
1550PDFR-G40
1550PDFR-G50
1550PDFR-G50
13T3PDER-M8
J020
XDGT1550PDFR-GL04 XDGT1550PDFR-GL04
1550PDFR-GL08
Page
XDGX227008PDFR-GL XDGX227008PDFR-GL AXD7000

227016PDFR-GL
227016PDFR-GL ^K056
1550PDER-G12
1550PDFR-GL08
Cutter Type
VFX6 ^K076
J030
XDGT1550PDER-G04 XDGT1550PDER-G04 BXD4000

1550PDER-G08
1550PDER-G08 ^K062
(ISO) Number
FBP415
^K018
J035
J042
Order Number
XDGX175004PDFR-GL XDGX175004PDFR-GL AXD4000

175008PDFR-GL
175008PDFR-GL ^K052
BAP3500
^K050
J018
J018
J018
13T3PDER-M8
ZCMX083508ERA
ZCMX083508ER-A
09T308ERA
09T308ER-A
ZCMX09T308ERB
ZCMX09T308ER-B
LER
^K078
J021
J021
J020
Memo
J043
GUIDE TO MILLING TOOLS

aSection
organization
zOrganized according to cutting mode for milling.

CUTTING MODE ICON

represents available cutting modes,
such as face milling and shoulder milling.
PHOTO OF PRODUCT
TYPE
GEOMETRY
PRODUCT FEATURES
SCOPE OF AVAILABLE WORK MATERIAL

provides a graph depicting the scope of the
available work material for machining.
CORNER ANGLE ICON
APPLICATION
PRODUCT
SECTION
STANDARDS FOR
APPLICABLE INSERTS
APPLICATION ICON
represents available
machining applications,
such as nishing
and roughing.
indicates stock status, dimensions,

etc. for applicable inserts.
MILLING
Max. Depth
of Cut
ap
Mass
(lbs)
Type
(Fig.)
D2
L1
D9
L7
D8
W1
L8
2.500
3.009
1.575
.750
.748
.415
.313
.187
.236
1.5
0304C
3.000
3.520
1.969
1.000
1.024
1.496
.375
.219
.236
2.4
0405E
4.000
4.518
1.969
.625
.375
0506E
5.000
5.513
2.480
1.500
1.378
2.362
.625
.375
.236
6.6
0607E
6.000
6.511
2.480
1.500
1.378
2.362
.625
.375
.236
10.4
0808M
8.000
8.509
2.480
1010M
1.500
1.378
2.362
.236
4.0
E E
13T3AGXN-JL
E X
JM breaker SEMT13T3AGSN-JM M S
JH breaker SEMT13T3AGSN-JH M S
5.512
1.000
.560
.236
14.6
2.500
1.378
7.087
1.000
.560
.236
23.7
2.000
2.513
1.575
.750
.748
.415
.313
.187
.236
.9
2505
2.500
3.009
1.575
.750
.748
.415
.313
.187
.236
1.5
0306C
3.000
3.520
1.969
1.000
1.024
1.496
.375
.219
.236
2.2
0407E
4.000
4.518
0508E
5.000
5.513
2.480
1.500
1.378
2.362
.625
.375
.236
6.2
0610E
10
6.000
6.511
2.480
1.500
1.378
2.362
.625
.375
.236
10.1
0812M
12
8.000
8.509
2.480
2.500
1.378
5.512
1.000
.560
.236
14.6
1014M
14
2.480
2.500
1.378
7.087
1.000
.560
.236
23.7
2.000
2.513
1.575
.750
.748
.415
.313
.187
.236
.9
0308C
3.000
3.520
1.969
1.000
1.024
1.496
.375
.219
.236
2.2
0410E
10
4.000
4.518
1.969
1.500
1.378
2.362
.625
.375
.236
3.8
WEEW13T3AGER8C
0512E
12
5.000
13T3AGTR8C
0616E
16
6.000
6.511
2.480
1.500
1.378
2.362
.625
.375
.236
10.3
0820M
20
8.000
8.509
2.480
2.500
1.378
5.512
1.000
.560
.236
14.6
1024M
24
10.000 10.508
2.480
2.500
1.378
7.087
1.000
.560
.236
23.7
NP-WEEW13T3AGFR3C
13T3AGTR3C
Extra Fine Pitch
10.000 10.508
5.513
1.969
1.500
2.480
1.500
1.378
1.378
2.362
.625
2.362
.375
.625
.236
.375
.236
3.7
6.4
Tool Holder
Number
Shim
x
Insert
c
ASX445 Type
Shim Screw
HTi10
Dimensions (inch)
Cermet Carbide
D1
Insert Screw
TPS35
Geometry
.528 .156 .078 .059
.528 .156 .078 .059
.528 .156 .078 .059
SEGT13T3AGFN-JP G F
.528 .156 .098
WIPER INSERTS
Dimensions (inch)
Coated Cermet Uncoated CBN PCD
Shape
Order Number
L1
L2
S1
F1
Geometry
Re
.649 .651 .156 .323 .059
.649 .651 .156 .323 .059
a
a
.649 .651 .156 .130 .059

.649 .651 .156 .130 .059
Wrench (Insert) Wrench (Shim)
TIP15T
HKY35R
SPARE PARTS
M001
TECHNICAL DATA
N001
K011
PAGE REFERENCE

SPARE PARTS
TECHNICAL DATA
indicates reference pages, including the above,
on the right hand page of each double-page spread.
PRODUCT STANDARDS
indicates tool types, order numbers, stock
status (per right/left hand), dimensions, etc.
SPARE PARTS FOR FACE MILL

indicates part numbers of the applicable
spare parts.
CUTTING EDGE ANGLE FOR

FACE MILLING
K000
Re
* Clamp Torque (lbf-in) : WCS503507H=44, TPS35=31
INSERT SEAT LOCATION
aTo
F1
.528 .156 .078 .059
S1
.528 .156 .078 .059
STASX445N WCS503507H
JP breaker
Honing
VP15TF
For Aluminum
Alloy
1.378
2.480
Fine Pitch
2.500
10
10.000 10.508
FT breaker SEMT13T3AGSN-FT M S
JL breaker SEET13T3AGEN-JL
ASX445R0204
SPARE PARTS
K008
Order Number
Coated
MILLING
Coarse Pitch
Dimensions (inch)
D1
ASX445R0205
MILLING
Stock Number
R of Teeth
a
ASX445R2504
Hardened Materials
MD220
Type
Order Number

T :+449
+953
I :+2255
+2302
MB710
C H :45
A.R :+20 +23
R.R :-13 -10
y ARBOR TYPE
Honing :
E : Round F : Sharp S : Chamfer + Round T : Chamfer
X : Round (Small)
Non-Ferrous Metal
HTi05T
breakers.
a Screw-on type.
a High rigidity due to employment
of a carbide shim.
Shape
Cast Iron
NX4545
Fig.3
: Stable Cutting
: General Cutting
: Unstable Cutting
Stainless Steel
VP30RT
20 positive insert.
a A wide range of chip
Steel
VP15TF
a Precision molded
P
M
K
N
S
H
MC5020
Work Material
Class
Honing
General Steel Stainless Steel Hardened Steel
F7030
Fig.2
F7010
Cast Iron
INSERTS WITH BREAKER
Roughing
Fig.1
NX2525
Light Alloy
Finishing
Roughing
MediumHeavy Light Semi
Finish Light Application
For Cast Iron
Cutting
-Heavy Cutting
Cutting
FACE
MILLING
<GENERAL CUTTING>
ASX445
Order:
For title product, please specify order number and hand of tool (right/left).
For insert,
please specify insert number and grade.
ROTATING TOOLS
MILLING TOOLS
CLASSIFICATION................................. K002
*Arranged by Alphabetical order

K014
K088
K017
K030
K038
K046
K080
K099
K022
K008
K052
K056
K066
K068
K050
K019
K108
K104
K112
K062
K114
K113
K018
K078
K141
K125
K124
K028
K137
K140
K139
K142
K070
K115
K128
K134
K136
K076
K020
AHX640W
AJX
AOX445
APX3000
APX4000
APX4000 (Long Cutting Edge)
AQX
ARX
ASX400
ASX445
AXD4000
AXD7000
BAP300
BAP300 (Long Cutting Edge)
BAP3500
BF407
BOE
BRP
BSP
BXD4000
CFSP
ECMP
FBP415
LER
LONG ARBORS
MBD/MBF
MBN
NSE300,400
PMC
PMF
PMR
SCREW-IN ARBORS
SPX
SRF
SRM2
SRM2 & 40/ & 50
TRM4
VFX6
VOX400
STANDARD OF MILLING
aFACE MILLING
ASX445 ..........................................
AHX640W .......................................
AOX445 ..........................................
FBP415 ...........................................
BF407 .............................................
aSHOULDER MILLING
VOX400 ..........................................
ASX400 ..........................................
NSE300,400 ...................................
BAP300 ..........................................
aDEEP SHOULDER MILLING
APX4000 (Long Cutting Edge) .......
BAP300 (Long Cutting Edge) .........
SPX .................................................
VFX6 ...............................................
LER .................................................
aMULTI FUNCTION MILLING
APX3000 ........................................
APX4000 ........................................
BAP3500 ........................................
AXD4000 ........................................
AXD7000 ........................................
BXD4000 ........................................
AQX ................................................
AJX .................................................
ARX ................................................
BRP ................................................
BOE ................................................
BSP ................................................
ECMP .............................................
aRADIUS MILLING
MBD/MBF .......................................
aCHAMFER MILLING
CFSP ..............................................
aBALL NOSE END MILL
SRF .................................................
MBN ................................................
SRM2 ..............................................
SRM2 & 40/ & 50 ..............................
TRM4 ..............................................
aVERTICAL FEED MILLING
PMC ................................................
PMR ................................................
PMF ................................................
LONG ARBORS .............................
aSCREW-IN ARBORS ......................
K008
K014
K017
K018
K019
K020
K022
K028
K066
K046
K068
K070
K076
K078
K030
K038
K050
K052
K056
K062
K080
K088
K099
K104
K108
K112
K113
K125
K114
K115
K124
K128
K134
K136
K137
K139
K140
K141
K142
K001
MILLING
CLASSIFICATION (ARBOR TYPE)

*Arranged by corner angle.
45
40
Face Milling
45
15
MILLING
K002
Multi Functional Multi Functional Multi Functional General Cutting for High Feed Cutting High Efciency High Feed Cutting
General Cutting
Milling
Milling
Milling
Aluminum Alloy
for Cast Iron
Cutting for Cast Iron
for Cast Iron
Cutting Corner AppliMode Angle cation
Product Name Shape
ASX445
AHX640W
Corner Angle,
Max. Depth of Cut
Features
a Precision molded 20 positive
insert.
a A wide range of chip breakers.
a Screw-on type.
a High rigidity due to
employment of a carbide
shim.
a Heptagonal
double-sided insert.
14
corner use.
a Fine pitch design
allows high feed
milling.
a Economical
AOX445
BF407
AJX
2.000"
2.500"
3.000"
4.000"
5.000"
6.000"
8.000"
10.000"
3.000"
4.000"
5.000"
6.000"
8.000"
10.000"
12.000"
solid CBN insert.

(when depth of cut is 3mm)
a High efciency machining
from roughing to nishing.
a Easy operation and
cleaning.
a 11 positive insert.
a Large axial angle
prevents chattering.
a Multi insert design.
a Enables high feed
machining.
a For cast iron
machining.
a High rake and high
relief angle.
a Suitable for light
alloy machining.
clamp structure.
(Max. Depth of Cut : .236")
K014
63
80
100
125
160
200
(Max. Depth of Cut : 8mm)
3.150"
3.937"
4.921"
6.299"
7.874"
9.843"
12.402"
3.150"
3.937"
4.921"
6.299"
7.874"
9.843"
12.402"
3.000"
4.000"
cutting.
4.921"
a Special insert design with 6.299"
the use of 3 cutting edges.
BOE
K008
K017
K018
K019
a Air / coolant through.
2.000"
a High rigidity due to double 2.500"
a Suitable for high feed
BRP
a Octagonal double-sided
a Economical 16 corner use.
FBP415
Work Material
Cutter
Dia. Light Alloy Cast Iron General Steel Stainless Steel Hardened Steel
a Round shape insert
gives strong cutting

edge.
a A wide variety of
lengths available.
a Suitable for machining
of die and mold.
a 20positive insert.
a Compatible with
8-corner use insert
and round type insert.
a Multi functional
milling.
1.500"
2.000"
2.500"
3.000"
4.000"
1.250"
1.500"
2.000"
2.480"
2.500"
3.000"
3.150"
3.937"
4.921"
6.300"
8.000"
(Max. Depth of Cut : .039", .059", .079")
K089
(Max. Depth of Cut : .240", .302")
K105
(Max. Depth of Cut : .276", .354")
K109
*Arranged by No. of available corners.
Shoulder Milling
10
VOX400
Features
aVertical inserts with
high strength cutting
edge.
aEconomical 8 corner
use.
aScrew-on type.
2.000"
2.500"
3.000"
4.000"
5.000"
6.000"
8.000"
10.000"
a Economical
due to the
use of 4 cutting edges.
a Low resistance due to
the 3D design of the
curved cutting edge.
a Curved cutting edge
and high rigidity holder.
2.000"
2.500"
3.000"
4.000"
5.000"
6.000"
8.000"
10.000"
a High rake angle.
a Enables highly
NSE300
2.000"
2.500"
3.150"
3.937"
NSE400
3.150"
3.937"
4.921"
6.299"
7.874"
90
ASX400
NSE300/NSE400
Work Material
Cutter
Dia. Light Alloy Cast Iron General Steel Stainless Steel Hardened Steel
efcient machining.
VOX400
K020
K022
K028
K028

a Low resistance insert and
APX3000
high rigidity body.
2.000"
a Ideal chip control.
a High wall accuracy can be 2.500"
produced by using this

cutter and unique insert
geometry.
high rigidity body.
K031
2.000"

2.500"
a High wall accuracy can be 3.000"
4.000"
90
geometry.
a High rake insert.
a Copy milling is
1.500"
2.000"
possible.
BAP3500

a Low resistance
inserts.
a High balance quality.
a Excellent wall
90
AXD7000

a Low resistance insert and
APX4000
AXD4000
3.000"
accuracy.
functional
milling.
a Multi
K039
2.500"
3.000"
2.000"
2.500"
3.000"
4.000"
5.000"
AXD4000
K050
K052
MILLING
Corner Angle,
Max. Depth of Cut
.591"
Product Name Shape
15.5
Aluminum Alloy for

Multi Functional Multi Functional General Cutting and Multi Functional Multi Functional General Cutting (NSE300) General Cutting For Cast Iron
Difcult-to-cut Material Cutting
Milling
Milling
Heavy Cutting
Milling
Milling
Heavy Cutting (NSE400)
Cutting Corner AppliMode Angle cation

a Low resistance
inserts.
a Excellent wall
accuracy.
a Multi functional
milling.
BXD4000

a Low resistance inserts
& high rigidity body.

Fly Insert
mechanism guarantees
secure high-revolution
milling.
a The Anti
2.000"
3.000"
(Max. Depth of Cut : .803", .827")
K056
1.500"
2.000"
2.500"
3.000"
4.000"
K063
K003
MILLING
CLASSIFICATION (SHANK TYPE)

Product Name Shape
Corner Angle,
Max. Depth of Cut
Features
Product Name Shape
due to the
a Low resistance due to the
3D design of the curved
cutting edge.
a Curved cutting edge and
high rigidity holder.
a Max. depth of cut .394".
& 1.250" & 2.000"
90
a Economical
VFX6

a Low resistance insert
SPX
^ K030
^ K038
1.220''3.543''
efciency milling
titanium alloys.
a On-edge style inserts with
high strength cutting edge.
& 63 & 100mm
^ K076
90
and
a The
2.835"8.100"
.394"(APX3000)
.591"(APX4000)
^ K023
APX3000
APX4000
Features
a High
.394"
ASX400
Corner Angle,
Max. Depth of Cut
high rigidity body.

a High wall accuracy
can be
geometry.
& .500" & 1.500"
wavy cutting edge

helps to reduce cutting
resistance.
a Suitable for heavy
machining due to holder
rigidity.
& 1.969" & 2.000"
90
^ K070
.433"
BAP3500

a High rake insert.
a Copy milling is possible.
a Max.depth of cut .433".
a Different
helical ute
angles prevents
chattering.
a Suitable for heavy cutting
due to holder rigidity.
& 1.000" & 2.000"
LER
& .750" & 1.250"
90
^ K050
^ K078
a Inserts with various
BAP300
a Precision
molded 20
positive insert.
breakers.
a Screw-on type.
a High rigidity due to
employment of a carbide
shim.
& 50 & 80mm
ASX445
chipbreakers and grades

are available.
& .500" & 1.500"
^ K066
^ K010
.827"
AXD7000

a Low resistance
a Octagonal
double-sided
solid CBN insert.
a Easy operation and
cleansing.
& 50 & 63mm
AOX445
inserts.
a Excellent wall
accuracy.
functional
milling.
& 1.250" & 1.500"
90
^ K017
a Low resistance inserts
BXD4000
&
.750" 1.500" (STANDARD EDGE TYPE)

.281" .688" (SHORT EDGE TYPE)
^ K056
.591"
MILLING
a Multi
AQX
high rigidity body.

Fly Insert
mechanism guarantees
secure high-revolution
milling.
& 1.000" & 1.500"
a The Anti

a The center bottom cutting
edge enables drilling and

end milling without
prepared hole.
a Max.depth of cut .281"
1.500".
& .625" & 1.500"
90
^ K062
^ K080
a Inserts with various
BAP300
Long Cutting Edge
a 13, 15 positive insert.

a High rigidity due to double
AJX
.079"
chipbreakers and grades

are available.
& .750" & 2.000"
90
^ K068
K004
^ K088
clamp structure.
for high feed
cutting.
a Special insert design with
the use of 3 cutting edges.
& .625" & 2.000"
a Suitable
Corner Angle,
Max. Depth of Cut
Features
Product Name Shape
a Precision
ARX
M-class
15positive insert.
for various
machining applications.
& 10 & 25mm
PMR
a Round shape insert
PMF
Features
a1
directional cutting with

large overhang.
shape of curved
edge gives high rigidity
and low resistance.
& 50 & 80mm
a Effective
a Unique
^ K099
^ K139
BRP
gives
strong cutting edge.

a A wide variety of lengths
available.
a Suitable for machining of
die and mold.
a Max.depth of cut .146"
.302".
& .500" & 2.500"
^ K104
a Compatible with 8-corner
.354"
BOE
a2
directional cutting with

large overhang.
burring so no need for
hand nishing.
a High precision multi
directional insert ensures
highly accurate surfaces.
& 50 & 80mm
a No
^ K140
a Suitable for roughing
SRM2
use insert and round type

insert.
a Multi functional milling.
& 1.250" & 3.125"
^ K108
^ K128
a Multi-function
.276"
BSP
endmill for
plunging, contouring and
chamfer milling.
a Max.depth of cut .276".
& .375" & 1.500"
SRM2 & 40/&50

(& 1.575"/& 1.969")
to
semi-nishing of small
and medium molds.
a High rigidity body design.
a Low resistance
chipbreaker.
a Key type clamp.
a Shrink t ready.
& .625" & 1.250"
a Best
for roughing of
molds.
a Low resistance
chipbreaker.
a Highly rigid body.
& 40, & 50 mm
(& 1.575", & 1.969")
^ K134
45
^ K112
a Large
TRM4
a Unique
.433"
ECMP
insert seat
position facilitates smooth
initial cutting and stable
machining.
a Excellent chip disposal.
a 86rhombic shape
11positive insert.
& 1.000" & 1.500"
^ K136
a Excellent
.327"
CFSP
sharpness with
11positive inserts.
a 45chamfer series.
& .313" & 1.250"
^ K115
one clamp screw.

cutting edge.
& .312" & 1.250"
^ K114
undercutting trimmed
part of press mould.
a 2 directional cutting with
large overhang.
& 25 & 40mm
cutting edge
provides sharpness similar
to that of solid ball nose
end mills.
a Highly accurate corner
radius tolerance allows for
high precision nishing.
a Carbide shank type
available.
& .375" & 1.250"
a Insert with two edges.
a Simple clamp system with
MBN
45
ball-nose endmill
suitable for roughing of
large molds.
a Economical 3-corner-use
inserts.
rigid holder are stable in
heavy cutting.
& 1.500", & 2.000"
a S-shaped
SRF
^ K113
a Sharp
a For
PMC
Corner Angle,
Max. Depth of Cut
MILLING
Product Name Shape
^ K124
a Insert with two edges.
a Simple clamp system with
MBD
one clamp screw.

cutting edge.
& .500" & 1.000"
a Sharp
^ K137
^ K125
K005
MILLING
SELECTION CHART (SHANK TYPE)

Product Name
Cutting Mode
Slot
Milling
Shoulder
Milling
Spot
Milling
Contour
Milling
Chamfer
Milling
MILLING
Radius
Milling
Drilling
Copy
Milling
Face
Milling
K006
ASX400
^ K023
APX3000
APX4000
^ K030
K038
BAP300
^ K066
BAP3500
^ K050
AXD4000
AXD7000
^ K052
K056
BXD4000
^ K062
SPX
VFX
^ K070
K076
BAP300
LONG CUTTING EDGE
LER
^ K068
K078
ASX445
^ K010
AOX445
^ K017
AJX
ARX
BRP
BOE
BSP
ECMP
CFSP
^ K113
^ K114
PMC
PMR
PMF
^ K137
^ K080
^ K088
^ K099
^ K104
^ K108
^ K112
K138
K139
SRM2
TRM4
^ K128
K136
SRF
MBN
MBD
^ K115
K124
K125
MILLING
AQX
MULTI FUNCTIONAL MULTI FUNCTIONAL MULTI FUNCTIONAL MULTI FUNCTIONAL MULTI FUNCTIONAL MULTI FUNCTIONAL
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
K007
MILLING
FACE
MILLING
<GENERAL CUTTING>
ASX445
Light Alloy
Cast Iron
Finishing
Roughing
Fig.1
Fig.2
a Precision molded
20 positive insert.
Fig.3
breakers.
a Screw-on type.
a High rigidity due to employment
of a carbide shim.
C H :45
A.R :+20 +23
R.R :-13 -10
Type
y ARBOR TYPE
Order Number
Dimensions (inch)
Stock Number
R of Teeth
D1
D2
L1
D9
L7
D8
W1
L8
Max. Depth
of Cut
ap
Mass
(lbs)
Type
(Fig.)
2.500
3.009
1.575
.750
.748
.415
.313
.187
.236
1.5
0304C
3.000
3.520
1.969
1.000
1.024
1.496
.375
.219
.236
2.4
0405E
4.000
4.518
1.969
1.500
1.378
2.362
.625
.375
.236
4.0
0506E
5.000
5.513
2.480
1.500
1.378
2.362
.625
.375
.236
6.6
0607E
6.000
6.511
2.480
1.500
1.378
2.362
.625
.375
.236
10.4
0808M
8.000
8.509
2.480
2.500
1.378
5.512
1.000
.560
.236
14.6
1010M
10
10.000 10.508
2.480
2.500
1.378
7.087
1.000
.560
.236
23.7
ASX445R0204
2.000
2.513
1.575
.750
.748
.415
.313
.187
.236
.9
2505
2.500
3.009
1.575
.750
.748
.415
.313
.187
.236
1.5
0306C
3.000
3.520
1.969
1.000
1.024
1.496
.375
.219
.236
2.2
0407E
4.000
4.518
1.969
1.500
1.378
2.362
.625
.375
.236
3.7
0508E
5.000
5.513
2.480
1.500
1.378
2.362
.625
.375
.236
6.2
0610E
10
6.000
6.511
2.480
1.500
1.378
2.362
.625
.375
.236
10.1
0812M
12
8.000
8.509
2.480
2.500
1.378
5.512
1.000
.560
.236
14.6
1014M
14
10.000 10.508
2.480
2.500
1.378
7.087
1.000
.560
.236
23.7
1.575
.750
.748
.415
.313
.187
.236
.9
Fine Pitch
Coarse Pitch
ASX445R2504
ASX445R0205
Extra Fine Pitch
MILLING

T :+449
+953
I :+2255
+2302
2.000
2.513
0308C
3.000
3.520
1.969
1.000
1.024
1.496
.375
.219
.236
2.2
0410E
10
4.000
4.518
1.969
1.500
1.378
2.362
.625
.375
.236
3.8
0512E
12
5.000
5.513
2.480
1.500
1.378
2.362
.625
.375
.236
6.4
0616E
16
6.000
6.511
2.480
1.500
1.378
2.362
.625
.375
.236
10.3
0820M
20
8.000
8.509
2.480
2.500
1.378
5.512
1.000
.560
.236
14.6
1024M
24
10.000 10.508
2.480
2.500
1.378
7.087
1.000
.560
.236
23.7
SPARE PARTS
z
Tool Holder
Number
Shim
x
Insert
c
K008
ASX445 Type
*c
Shim Screw
Insert Screw
STASX445N WCS503507H
Clamp Torque (lbf-in) : WCS503507H=44, TPS35=31
*
TPS35
TIP15T
HKY35R
Fig.2
Fig.1
80, 100 only
Fig.4
Fig.3
(315 only)
(315 only)
METRIC Standard
For metric arbors
Extra Fine Pitch
Fine Pitch
Coarse Pitch
Type
y ARBOR TYPE
Order Number
Stock Number
R of Teeth
T :+449
+953
I :+2255
+2302
Dimensions (mm)
D1
D2
L1
D9
L7
D8
D12
W1
L8
Max. Depth
of Cut
ap
Mass
(kg)
Type
(Fig.)
ASX445-050A03R
50
63.0
40
22
20
11
45
10.4
6.3
-063A04R
63
75.9
40
22
20
11
50
10.4
6.3
0.7
-080A04R
80
93.2
50
27
22
13.5
56
12.4
1.0
-100A05R
100
113.2
50
32
25
17.5
70
14.4
1.6
-125B06R
125
138.0
63
40
32
56
80
16.4
2.4
-160C07R
160
173.0
63
40
29
56
100
16.4
3.9
-200C08R
200
212.9
63
60
32
135
155
25.7
14
6.7
-250C10R
10
250
262.9
63
60
32
174
200
25.7
14
10.5
-315C14R
14
315
327.9
80
60
57
256.8
285
25.7
14
22.4
ASX445-050A04R
50
63.0
40
22
20
11
45
10.4
6.3
0.4
-063A05R
63
75.9
40
22
20
11
50
10.4
6.3
0.6
-080A06R
80
93.2
50
27
22
13.5
56
12.4
0.9
-100A07R
100
113.2
50
32
25
17.5
70
14.4
1.5
-125B08R
125
138.0
63
40
32
56
80
16.4
2.3
-160C10R
10
160
173.0
63
40
29
56
100
16.4
3.6
-200C12R
12
200
212.9
63
60
32
135
155
25.7
14
5.8
-250C14R
14
250
262.9
63
60
32
174
200
25.7
14
10.6
-315C18R
18
315
327.9
80
60
57
256.8
285
25.7
14
22.2
ASX445-050A05R
50
63.0
40
22
20
11
45
10.4
6.3
0.4
-063A06R
63
75.9
40
22
20
11
50
10.4
6.3
0.6
-080A08R
80
93.2
50
27
22
13.5
56
12.4
0.9
-100A10R
10
100
113.2
50
32
25
17.5
70
14.4
1.5
-125B12R
12
125
138.0
63
40
32
56
80
16.4
2.3
-160C16R
16
160
173.0
63
40
29
56
100
16.4
3.6
-200C20R
20
200
212.9
63
60
32
135
155
25.7
14
6.5
-250C24R
24
250
262.9
63
60
32
174
200
25.7
14
10.3
-315C28R
28
315
327.9
80
60
57
256.8
285
25.7
14
21.8
0.5
INSERTS
K011
SPARE PARTS
M001
TECHNICAL DATA
N001
MILLING
C H :45
A.R :+20 +23
R.R :-13 -10
K009
MILLING
Fig.1
Fig.2
Fig.3
METRIC Standard
For inch arbors
C H :45
A.R :+20 +23
R.R :-13 -10
Order Number
ASX445R08004C
R10005D
R12506E
R16007F
R20008K
R25010K
R31514P
ASX445R08006C
R10007D
R12508E
R16010F
R20012K
R25014K
R31518P
ASX445R08008C
R10010D
R12512E
R16016F
R20020K
R25024K
R31528P
Stock Number
R of Teeth
s
s
4
5
6
7
8
10
14
6
7
8
10
12
14
18
8
10
12
16
20
24
28
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
T :+449
+953
I :+2255
+2302
D1
D2
L1
D9
L7
D8
W1
L8
Max. Depth
of Cut
ap
80
100
125
160
200
250
315
80
100
125
160
200
250
315
80
100
125
160
200
250
315
93.2
113.2
138.0
173.0
212.9
262.9
327.9
93.2
113.2
138.0
173.0
212.9
262.9
327.9
93.2
113.2
138.0
173.0
212.9
262.9
327.9
50
50
63
63
63
63
63
50
50
63
63
63
63
63
50
50
63
63
63
63
63
25.4 [1.0"]
31.75 [1.25"]
38.1 [1.5"]
50.8 [2.0"]
47.625 [1.875"]
47.625 [1.875"]
47.625 [1.875"]
25.4 [1.0"]
31.75 [1.25"]
38.1 [1.5"]
50.8 [2.0"]
47.625 [1.875"]
47.625 [1.875"]
47.625 [1.875"]
25.4 [1.0"]
31.75 [1.25"]
38.1 [1.5"]
50.8 [2.0"]
47.625 [1.875"]
47.625 [1.875"]
47.625 [1.875"]
26
32
35
38
35
35
40
26
32
35
38
35
35
40
26
32
35
38
35
35
40
38
45
60
80
140
180
245
38
45
60
80
140
180
245
38
45
60
80
140
180
245
9.5
12.7
15.9
19.1
25.4
25.4
25.4
9.5
12.7
15.9
19.1
25.4
25.4
25.4
9.5
12.7
15.9
19.1
25.4
25.4
25.4
6
8
10
11
14
14
14
6
8
10
11
14
14
14
6
8
10
11
14
14
14
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Dimensions (mm)
[inch]
Mass
(kg)
Type
(Fig.)
1.1
1.8
2.9
4.7
7.9
12.9
22.4
1.0
1.7
2.8
4.6
7.8
12.8
22.2
1.1
1.8
2.9
4.7
7.8
12.8
21.8
1
1
1
1
2
2
3
1
1
1
1
2
2
3
1
1
1
1
2
2
3
MILLING
Extra Fine Pitch
Fine Pitch
Coarse Pitch
Type
y ARBOR TYPE
METRIC Standard
y SHANK TYPE
Order Number
ASX445R503S32
634S32
804S32
K010
Stock Number
R of Teeth
s
s
s
3
4
4
Dimensions (mm)
D1
D2
L1
D4
L2
Max. Depth of Cut

ap (mm)
50
63
80
63.0
75.9
93.2
125
125
125
32
32
32
40
40
40
6
6
6

(10 inserts in one case) (1 insert in one case for CBN/PCD)
For Aluminum
Alloy
: Stable Cutting
: General Cutting
: Unstable Cutting
Stainless Steel
Cast Iron
Honing :
E : Round F : Sharp S : Chamfer + Round T : Chamfer
X : Round (Small)
Non-Ferrous Metal
Hardened Materials
E X
JM breaker SEMT13T3AGSN-JM M S
JH breaker SEMT13T3AGSN-JH M S
HTi10
Dimensions (inch)
D1
S1
F1
Re
Geometry
.528 .156 .078 .059

.528 .156 .078 .059
FT breaker SEMT13T3AGSN-FT M S
JP breaker
MC5020
NX4545
13T3AGXN-JL
VP30RT
E E
Cermet Carbide
VP15TF
JL breaker SEET13T3AGEN-JL
F7030
Order Number
Coated
F7010
Shape
Steel
Class
Honing
Roughing
MediumHeavy Light Semi
Finish Light Application
For Cast Iron
Cutting
-Heavy Cutting
Cutting
Work Material
P
M
K
N
S
H
.528 .156 .078 .059
.528 .156 .078 .059
.528 .156 .078 .059
SEGT13T3AGFN-JP G F
.528 .156 .098
WIPER INSERTS
Dimensions (inch)
13T3AGTR8C
NP-WEEW13T3AGFR3C
13T3AGTR3C
MD220
MB710
HTi05T
L1
L2
S1
F1
Geometry
Re
MILLING
WEEW13T3AGER8C
NX2525
Order Number
Honing
VP15TF
Coated Cermet Uncoated CBN PCD
Shape
.649 .651 .156 .323 .059
.649 .651 .156 .323 .059
a
a
.649 .651 .156 .130 .059

.649 .651 .156 .130 .059
SPARE PARTS
M001
TECHNICAL DATA
N001
K011
MILLING
Work Material
Hardness
P
Mild Steel
< 180HB
180 280HB
Carbon Steel
Alloy Steel
280 350HB
M
Stainless Steel
K
Cast Iron
Aluminum Alloy
Nickel High Alloy
H Heat-Treated Steel
< 270HB
Grade
Cutting Speed
(SFM)
Finish Light Cutting LightSemi-Heavy Cutting MediumHeavy Cutting

Feed per Tooth (inch/tooth) Breaker Feed per Tooth (inch/tooth) Breaker Feed per Tooth (inch/tooth) Breaker
F7010/F7030
920 (690 1150)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
.012 (.008 .016)
JH
VP15TF
820 (655 985)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
.012 (.008 .016)
JH
VP30RT
755 (590 920)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
.012 (.008 .016)
JH
NX4545
590 (425 755)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
F7010/F7030
820 (655 985)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
.012 (.008 .016)
JH
VP15TF
720 (560 885)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
.012 (.008 .016)
JH
VP30RT
490 (395 590)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
NX4545
490 (390 590)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
F7010/F7030
590 (425 755)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
.012 (.008 .016)
JH
VP15TF
460 (330 590)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
.012 (.008 .016)
JH
VP30RT
330 (260 395)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
NX4545
330 (260 390)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
VP15TF
720 (560 885)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
.012 (.008 .016)
JH
VP30RT
655 (490 820)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
.012 (.008 .016)
JH
NX4545
490 (395 590)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
Tensile Strength
< 450MPa
MC5020
655 (400 820)
.008 (.004 .012)
JM
.012 (.008 .016)
JH
FT
VP15TF
590 (425 826)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
.012 (.008 .016)
JH
HTi10
2130 (1000 3300) .006 (.004 .008)
JP
.008 (.004 .012)
JP
.012 (.008 .016)
JP
VP15TF
130 (65 165)
.006 (.004 .008)
JL
.008 (.004 .012)
JM
40 55HRC
VP15TF
260 (195 330)
.004 (.002 .006)
JL
.006 (.004 .008)
JM
.008 (.004 .012)
JH
INSTRUCTIONS FOR USING INSERTS

y INSTRUCTIONS FOR USE OF THE JP BREAKER
a The JP breaker has sharp cutting edges.
Wear gloves when handling.
MILLING
a When machining aluminum alloy, welding to
K012
the cutting edge tends to occur, often leading

to insert failure. To prevent this, wet cutting is
recommended.
y INSTRUCTIONS FOR USE OF WIPER INSERTS

a Wiper inserts for the ASX445 are
single-cornered.
a When installing the wiper insert, place the
insert so that the cutting edge is located as

shown.
FEATURES
y STABLE, LONG TOOL LIFE, HIGH ACCURACY BODY
A carbide shim with Mitsubishi's proprietary
Anti-Fly Insert (AFI) mechanism provides
excellent insert location characteristics,
permitting stable cutting even under high
load conditions.
The cutter body is made from a special

alloy that provides high strength at high
temperature. A special surface treatment
improves the corrosion resistance.
The ASX cutter uses screw-on type inserts

that allow easy clamping of the inserts with
high location
precision. Indexing
of the inserts can
be performed
without completely
removing the screw.
y EFFECTIVE FOR VARIOUS MACHINING APPLICATIONS

a Coarse Pitch Type
1. The 1st recommendation
for cutting steel and
stainless steel.
2. For deep cutting and high
feed rates with large-volume
chip discharge.
3. Longer overhang possible for
relatively low machining riidity.
a Extra Fine Pitch Type
a Fine Pitch Type

for cast iron.
2. For cutting operations
where chip dischange
volume is small and
high table feed is
desired.

type for cast iron,
hardened steel and
heat-resistant alloys.
2. For shallow cutting with
low feed rates and lowvolume chip discharge.
y CHIPBREAKERS FOR A WIDE RANGE OF APPLICATIONS
High accuracy insert with

ground-nished periphery.
Large rake angle leading
to low cutting resistance.
zWorkpiece rigidity is
low.
JM
Light to
Semi-Heavy cutting
Breaker
JH
Medium to
Heavy cutting
Breaker
High accuracy M class insert. High accuracy M class insert.

For a wide range of work- Strong cutting edge for high
piece materials and cutting fracture resistance.
conditions.
zGeneral cutting.
zInterrupted cutting.
xScaling.
JP
Aluminum alloy
cutting
Breaker
FT
Rough cutting
for cast iron
Breaker
High accuracy insert with ground-nished High accuracy M class inserts.

periphery. Large rake angle and mirror- High fracture-resistant at-top
finished rake face for sharp cutting inserts.
performance and high welding resistance.
zGeneral machining of aluminum
and non ferrous metal.
xHigh feed cutting.
zFor rough machining

of scaled cast iron.
y INSERT GRADES FOR A WIDE RANGE OF MATERIALS

Stainless Steel
Aluminum Alloy
S Heat Resistant Alloy
H Heat Treated Steel
VP15TF
VP15TF
Cutting
Stable Conditions
Unstable
Cutting
Stable Conditions
Unstable
Low
Cutting
Speed
High
MILLING
JL
Finish to
Light cutting
Breaker
Cutting
Stable Conditions
Unstable
Cutting
Stable Conditions
Unstable
Cutting
Stable Conditions
Unstable
Cutting
Stable Conditions
Unstable
(Note) When machining steel or stainless steel where the emphasis is on surface nish, use cermet grade NX4545.
Stable Cutting : Continuous cutting, Constant depth of cut, Pre-machined securely clamped component cutting
Unstable Cutting : Heavy interrupted, Irregular depth of cut, Low clamping rigidity cutting
K013
MILLING
FACE
MILLING
<HIGH FEED CUTTING FOR CAST IRON>
AHX640W
Light Alloy
Cast Iron
Finishing
Roughing
Fig.1
Fig.2
Fig.3
Fig.4
a Heptagonal double-sided
insert.
a Fine pitch design allows
high feed milling.
Super Extra Fine Pitch
Extra Fine Pitch
Type
C H :40
A.R :-6
R.R :-4
T :+10
I :+9 +10 (T, I : When using the MK breaker insert)
Order Number
AHX640WR/L0308D
0410E
0512E
0614F
0820M
1024M
1228M
AHX640WR/L0310D
0414E
0518E
0620F
0828M
1036M
1242M
Stock Number
R L of Teeth
Dimensions (inch)
D2
D1
L1
D9
W1
L8
Mass
(lbs)
Type
(Fig.)
4.2
7.3
1
1
3.000
4.000
3.494 2.500 1.250 1.260

4.494 2.500 1.500 1.181
.669
.787
2.874
3.799
.500 .281
.625 .375
.236
.236
a r
12
5.000
5.494 2.500 1.500 1.378 2.362
3.799
.625 .375
.236
8.8
a r
14
6.000
6.494 2.500 2.000 1.496 3.150
4.724
.750 .437
.236
12.6
a r
20
8.000
8.494 2.500 2.500 1.378 5.512
6.890 1.000 .560
.236
19.6
a r
24
28
10.000 10.494 2.500 2.500 1.378 7.087 8.661 1.000 .560

12.000 12.494 2.500 2.500 1.575 9.646 11.220 1.000 .560
.236
.236
32.0
49.2
3
4
a r
a r
10
14
3.000
4.000
3.494 2.500 1.250 1.260

4.494 2.500 1.500 1.181
.669
.787
2.874
3.799
.500 .281
.625 .375
.236
.236
4.2
7.3
1
1
a r
18
5.000
5.494 2.500 1.500 1.378 2.362
3.799
.625 .375
.236
8.8
a r
20
6.000
6.494 2.500 2.000 1.496 3.150
4.724
.750 .437
.236
12.6
a r
28
8.000
8.494 2.500 2.500 1.378 5.512
6.890 1.000 .560
.236
19.6
a r
36
42
10.000 10.494 2.500 2.500 1.378 7.087 8.661 1.000 .560

12.000 12.494 2.500 2.500 1.575 9.646 11.220 1.000 .560
.236
.236
32.0
49.2
3
4
a r
a r

Class
Honing
MC5020
MILLING
D12
8
10
Coated
Order Number
D8
a r
a r
INSERTS
Shape
L7
Max. Depth
of Cut
ap
MK breaker NNMU200608ZEN-MK M E
Work Material
Geometry
K
Gray
Cast Iron
Ductile
Cast Iron
HK breaker NNMU200608ZEN-HK M E
Tensile
Strength
Grade
Cutting Speed Feed per Tooth

(SFM)
(inch/tooth)
< 200MPa
985
(820 1150)
.012
(.008 .016)
250 350
MPa
720
(490 985)
.012
(.008 .016)
< 450MPa
655
(490 820)
.008
(.004 .012)
500 800
MPa
555
(490 655)
.008
(.004 .012)
MC5020
MK
HK
Extra Fine Pitch
Wiper
WNEU2006ZEN7C-WK M E
General Cutting
Unstable Cutting
High
Machine rigidity
Low
(Note) When the workpiece has poor clamping rigidity and the tool
overhang is long, reduce the cutting speed and feed by 2030%.
a
K014
Fig.1
Fig.2
Fig.3
Fig.4
(315 only)
METRIC Standard
For metric arbors
T :+10
Order Number
Stock Number
R L of Teeth
D1
D2
L1
D9
L7
D8
D12
W1
L8
Max. Depth
of Cut
ap
Dimensions (mm)
Mass
(kg)
Type
(Fig.)
AHX640W-080A08R/L
s s
80
92.6
50
27
23
13
56
12.4
1.5
-100B10R/L
s s
10
100
112.6
50
32
32
45
70
14.4
2.1
-125B12R/L
s s
12
125
137.6
63
40
32
56
80
16.4
3.1
-160C16R/L
s s
16
160
172.6
63
40
29
56
100
16.4
5.6
-200C20R/L
s s
20
200
212.6
63
60
32
135
155
25.7
14
8.0
-250C24R/L
s s
24
250
262.6
63
60
32
180
200
25.7
14
12.6
-315C28R/L
s s
28
315
327.6
80
60
57
225
285
25.7
14
31.5
AHX640W-080A10R/L
s s
10
80
92.6
50
27
23
13
56
12.4
1.5
-100B14R/L
s s
14
100
112.6
50
32
32
45
70
14.4
2.1
-125B18R/L
s s
18
125
137.6
63
40
32
56
80
16.4
3.1
-160C22R/L
s s
22
160
172.6
63
40
29
56
100
16.4
5.6
-200C28R/L
s s
28
200
212.6
63
60
32
135
155
25.7
14
8.0
-250C36R/L
s s
36
250
262.6
63
60
32
180
200
25.7
14
12.6
-315C44R/L
s s
44
315
327.6
80
60
57
225
285
25.7
14
31.5
MILLING
Extra Fine Pitch
Type
C H :40
A.R :-6
R.R :-4
SPARE PARTS
*
Tool Holder
Number
AHX640W Type
Wedge
Clamp Screw
Wrench
CWAHX640WN
LS0622T
TKY15T
* Clamp Torque (lbf-in) : LS0622T=53
SPARE PARTS
M001
TECHNICAL DATA
N001
K015
MILLING
Fig.1
Fig.2
Fig.3
Fig.4
METRIC Standard
For inch arbors
T :+10
Order Number
Stock Number
R L of Teeth
K016
Dimensions (mm)
D1
D2
L1
D9
[1.0"]
[inch]
L7
D8
26
Max. Depth
of Cut
ap
Mass
(kg)
Type
(Fig.)
D12
W1
L8
13
56
9.5
1.5
32
45
70 12.7
2.1
AHX640WR/L08008C
s s
80
92.6
50
25.4
10010D
s s
10
100
112.6
50
31.75 [1.25"]
12512E
s s
12
125
137.6
63
38.1
[1.5"]
35
56
80 15.9 10
3.5
16016F
s s
16
160
172.6
63
50.8
[2.0"]
38
72 100 19.1 11
5.6
63
47.625 [1.875"]
35
140 175 25.4 14.22
9.0
35
180 220 25.4 14.22
14.4
40
225 285 25.4 14.22
23.8
20020K
s s
25024K
s s
24
250
262.6
63
47.625 [1.875"]
31528P
s s
28
315
327.6
63
47.625 [1.875"]
AHX640WR/L08010C
s s
10
80
92.6
50
25.4
10014D
s s
14
100
112.6
50
31.75 [1.25"]
12518E
s s
18
125
137.6
63
38.1
16022F
s s
22
160
172.6
63
50.8
20028K
s s
28
200
212.6
63
47.625 [1.875"]
35
25036K
s s
36
250
262.6
63
47.625 [1.875"]
31544P
s s
44
315
327.6
63
47.625 [1.875"]
20
MILLING
Extra Fine Pitch
Type
C H :40
A.R :-6
R.R :-4
200
212.6
[1.0"]
26
13
56
9.5
1.5
32
45
70 12.7
2.1
[1.5"]
35
56
80 15.9 10
3.5
[2.0"]
38
72 100 19.1 11
5.6
140 175 25.4 14.22
9.0
35
180 220 25.4 14.22
14.4
40
225 285 25.4 14.22
23.8
FACE
MILLING
<HIGH EFFICIENCY CUTTING FOR CAST IRON>
AOX445
Fig.2
Fig.1
a Octagonal double-sided
solid CBN insert.
(Max. Depth of Cut)
Cast Iron
Roughing
(Max. Depth of Cut)
Light Alloy
Finishing
Fig.3

a Easy operation and cleaning.
y ARBOR TYPE
Type
Order Number
Coarse Pitch
Stock
AOX445-063A04R/L
R/L08006C
R/L10008D
R/L12510E
R/L16012F
R/L20012K
R L
s r
s r
s r
s r
s r
s r
T :-9 -6
I :-5
Number
of Teeth
C H :45
A.R :-5
R.R :-9 -6
For inch arbors
(Max. Depth of Cut)
METRIC Standard
D1
D2
L1
D9
L7
D8
4
6
8
10
12
12
63
80
100
125
160
200
70.75
87.73
107.73
132.71
167.71
207.71
40
50
50
63
63
63
22
25.4 [1.0"]
31.75 [1.25"]
38.1 [1.5"]
50.8 [2.0"]
47.625 [1.875"]
20
26
32
35
38
35
11
38
45
60
80
140
Dimensions (mm)
Max.
Max.
Mass Depth of Cut Spindle Type
Speed (Fig.)
(mm)
(kg)
-1
A1 ap (min )
[inch]
W1
L8
10.4 6.3
9.5 6
12.7 8
15.9 10
19.1 11
25.4 14.22
0.6
1.1
2.4
2.9
4.6
8.3
3
3
3
3
3
3
8
8
8
8
8
8
12000
11000
9300
8300
7200
6400
1
2
2
2
2
3
(Note) When machining with a depth of cut of over 3mm, 16 corners cannot be used.
(Max. Depth of Cut)
METRIC Standard
Stock
Order Number
R L
AOX445R/L503S32
R/L634S32
s r
s r
D1
D2
L1
D4
L2
3
4
50
63
57.75
70.75
125
125
32
32
40
40
Dimensions (mm)
Mass
(kg)
1.0
1.3
Max.
Depth of Cut
A1
ap
Max.
Spindle
Speed
(min-1)
3
3
8
8
13000
12000
(mm)
SPARE PARTS
INSERTS
SL-ONEN120404ASN
BC5030
Class
CBN
Order Number
Tool Holder
Number
Geometry
AOX445
MILLING
Number
of Teeth
Coarse Pitch
Type
y SHANK TYPE
Wedge
Clamp Screw
Wrench
CWAOX445N
LS15T
TKY25T
* Clamp Torque (lbf-in) : LS15T=71

Work Material
K
Gray
Cast Iron

(1 insert in one case for CBN)
Tensile
Strength
Grade

(SFM)
(inch/tooth)
BC5030
3280
(2625 4920)
< 200MPa
250 350
MPa
.004
(.002 .006)
SPARE PARTS
M001
TECHNICAL DATA
N001
K017
MILLING
FACE
MILLING
<HIGH FEED CUTTING FOR CAST IRON>
FBP415
Light Alloy
Cast Iron
Finishing
Roughing
Fig.2
Fig.1
a Large axial angle
prevents chattering.
a Enables high feed
(12" only)
Fig.3
(12" only)
machining.
a For cast iron
machining.
3", 4"
C H :15
A.R :+13
R.R :-2
5" 12"
C H :15
A.R :+13 T :+4
I :+12
R.R :+1
T :+2
I :+13
D9
L7
D8
W1
L8
Max. Depth
of Cut
ap
Dimensions (inch)
Stock Number
R of Teeth
Order Number
D1
D2
L1
Type
(Fig.)
FBP415R0308C
3.150
3.355 1.969
1.000
1.024
.512
.375
.219
.335
3.3
0410E
10
3.937
4.141 2.480
1.500
1.181
.787
.625
.375
.335
6.0
0514E
14
4.921
5.131 2.480
1.500
1.496
2.362
.625
.375
.335
8.0
0618F
18
6.299
6.509 2.480
2.000
1.496
3.150
.750
.437
.335
12.7
0822M
22
7.874
8.083 2.480
2.500
1.378
5.512
1.000
.560
.335
19.0
1028M
28
9.843 10.051 2.480
2.500
1.378
7.087
1.000
.560
.335
30.8
1234M
34
12.402 12.610 2.480
2.500
1.575
9.646
1.000
.560
.335
50.6
E E
42EETR1
E T
SPNN42EEER1
N E
Work
Material
CBN
UTi20T
HTi10
HTi05T
MB710
SPEN42EEER1

MC5020
F7010
NX2525
Order Number
Class
Honing
INSERTS
MILLING
Mass
(lbs)
a a a
r s
Geometry
Tensile
Strength
Grade

(SFM)
(inch/tooth)
< 200MPa
HTi10
655
(460 785)
.008
(.004 .012)
MC5020
820
(555 985)
.008
(.004 .012)
Gray
Cast Iron 250 350
MPa
HTi10
r s
< 450MPa
Ductile
Cast Iron
SPER42EEER-JS E E
MB710
500 800
MPa
JS breaker
1640
.006
(985 2950) (.002 .010)
525
.006
(360 620) (.004 .008)
MC5020
655
(425 785)
.008
(.004 .012)
MC5020
525
(360 620)
.008
(.004 .012)
MB710
655
(330 985)
.006
(.002 .010)
SPARE PARTS
WPC42EEER10C C E
42EETR10C C T
a
a
Tool
Holder
Number
Shim
Clamp Wrench Wrench

Shim
Wedge-T
Screw (Clamp Screw) (Shim)
Screw
FBP415R STSP415R TS32 CWSP415TR LS10T TKY25T TKY08F
* Clamp Torque (lbf-in) : LS10T=75, TS32=8.9

K018

(10 inserts in one case) (1 insert in one case for CBN)
a
r
FACE
MILLING
<GENERAL CUTTING FOR ALUMINUM ALLOY>
BF407
Light Alloy
Cast Iron
Finishing
Roughing
Fig.2
Fig.1
a High rake and high
(12" only)
Fig.3
(12" only)
relief angle.
a Suitable for light alloy
machining.
C H :7
A.R :+15
R.R :+12
T :+14
I :+14
BF407R0305C
0406E
0508E
0610F
0812M
1016M
1218M
D1
5
6
a
a
D9
L7
D8
W1
L8
Max. Depth
of Cut
ap
1.000
1.500
1.024
1.181
.512
.787
.375
.625
.219
.375
.354
.354
Dimensions (inch)
Stock Number
R of Teeth
Order Number
3.150
3.937
D2
L1
3.260 1.969
4.047 2.480
Type
(Fig.)
2.4
5.1
1
1
4.921
5.028 2.480
1.500
1.496
2.362
.625
.375
.354
10
6.299
6.406 2.480
2.000
1.496
3.150
.750
.437
.354
11
12
7.874
7.969 2.480
2.500
1.378
5.512
1.000
.560
.354
17
16
18
9.843 9.937 2.480

12.402 12.508 2.480
2.500
2.500
1.378
1.575
7.087
9.646
1.000
1.000
.560
.560
.354
.354
29
53.5
3
3
INSERTS
6.2

Work
Material
SFAN42ZFFR2
A F
SFCN42ZFFR2
C F
MD220
Carbide PCD
HTi10
Class
Honing
Order Number
Mass
(lbs)
Max
D.O.C
Geometry
Silicon (%)
HTi10
<2
MD220
.350
a
Grade
Aluminum
Alloy
.350
HTi10
10 Max.
MD220
HTi10
15 Max.
NP-WFC42ZFER2 C E
.098
NP-WFC42ZFER6 C E
.098
WFC42ZFER2
.236
C E
2200
(1300 3200)
3200
(2600 3900)
2200
(1300 3200)
3200
(2600 3900)
1300
(650 1900)
2000
(1300 2600)
.006
(.004 .010)
.006
(.002 .010)
.004
(.002 .006)
.006
(.002 .010)
.006
(.002 .010)
MILLING
MD220

(SFM)
(inch/tooth)
SPARE PARTS
z
*2
*1
Tool Holder
Number
Insert
Plug
BF407R0305C
0406E
BF407R0508E
BF407R1218M
Wedge
Clamp Screw
Adjusting Screw
Wrench
CWSF407TR1
LS15T
CAS51T
TKY25T
CWSF407TR2
LS15T
CAS51T
TKY25T
screw for factory use only.

*12 Adjusting
Clamp Torque (lbf-in) : LS15T=75
*
(10 inserts in one case) (1 insert in one case for PCD)
SPARE PARTS
M001
TECHNICAL DATA
N001
K019
MILLING
SHOULDER MILLING
VOX400
<STRONG EDGE TYPE FOR CAST IRON>
Carbon Steel Alloy Steel Stainless Steel Hardened Steel
200
250
D12
101.6
D9
W1
L8
Fig.3
D12
D9
W1
100
125
160
L7
L1
ap
ap
L1
L1
D8
D11
D1
D8
D1
D8
D1
ap
L7
63
80
Fig.2
D12
D9
W1
L8
Fig.1
L7
Cast Iron
L8
Light Alloy
Roughing
METRIC Standard
For inch arbors
MILLING
Fine Pitch
Coarse Pitch
VOX400-063A04R
R08004C
R10006D
R12508E
R16010F
R20012K
R25016K
VOX400-063A06R
R08008C
R10010D
R12512E
R16016F
R20020K
R25024K
Number of Teeth
Order Number
Stock
Type
y ARBOR TYPE
D1
L1
D9
L7
D8
D11
D12
W1
L8
17
20
50
55
10.4
9.5
6.3
6
0.6
1.0
10
[1.0"]
11
13
10
1
1
31.75
[1.25"]
32
45
70
12.7
1.5
10
63
38.1
[1.5"]
40
60
80
15.9 10
2.7
10
160
63
50.8
[2.0"]
43
80
120
19.1 11
5.3
10
12
16
200
250
63
63
47.625 [1.875"]
47.625 [1.875"]
35
35
130
180

175
220
25.4 14.22
25.4 14.22
8.5
13.3
10
3
3
6
8
63
80
40
50
22
25.4
[1.0"]
20
26
11
13
17
20
50
55
10.4
9.5
6.3
6
0.6
1.0
10
10
1
1
10
100
50
31.75
[1.25"]
32
45
70
12.7
1.5
10
12
125
63
38.1
[1.5"]
40
60
80
15.9 10
2.7
10
16
160
63
50.8
[2.0"]
43
80
120
19.1 11
5.3
10
63
63
47.625 [1.875"]
47.625 [1.875"]
35
35
130
180

175
220
25.4 14.22
25.4 14.22
8.5
13.3
10
3
3
63
80
40
50
22
25.4
100
50
125
10
s
s
s
s
s
20
24
200
250
*
Tool Holder Number
Clamp Screw
Wrench
CS401160T
TKY15T
* Clamp Torque (lbf-in) : CS401160T=31
K020
Max.
Mass
Depth of Cut Fig.
(kg)
ap (mm)
20
26
4
4
SPARE PARTS
VOX400
[inch]
Dimensions (mm)
10
10
160
200
250
L7
L1
ap
ap
L1
L1
D12
101.6(160:66.7)
D9
W1
L8
100
125
L8
L8
Fig.3
D12
D9
W1
L7
D8
D11
D1
D8
D1
METRIC Standard
D8
D1
ap
63
80
Fig.2
D12
D9
W1
L7
Fig.1
For metric arbors
Number of Teeth
Order Number
Stock
Type
y ARBOR TYPE
Fine Pitch
Coarse Pitch
VOX400-063A04R
-080A04R
-100B06R
-125B08R
-160C10R
-200C12R
-250C16R
VOX400-063A06R
-080A08R
-100B10R
-125B12R
-160C16R
-200C20R
-250C24R
Mass Max.
Depth of Cut Fig.
(kg)
ap (mm)
Dimensions (mm)
D1
L1
D9
L7
D8
D11
D12
W1
L8
*
Clamp
Screw
CS401160T
TKY15T
CS401160T
TKY15T
Wrench
4
4
63
80
40
50
22
27
20
23
11
13
17
20
50 10.4 6.3
56 12.4 7
0.6
1
10
10
1
1
6 100
50
32
32
45
78 14.4 8
1.7
10
CS401160T
TKY15T
8 125
63
40
32
56
89 16.4 9
10
CS401160T
TKY15T
10 160
63
40
29
56
120 16.4 9
5.4
10
CS401160T
TKY15T
12 200
16 250
63
63
60
60
32
32
130
180

175 25.7 14.22 8.1

210 25.7 14.22 11.8
10
3
3
CS401160T
TKY15T
CS401160T
TKY15T
63
80
40
50
22
27
20
23
11
13
17
20
50 10.4 6.3
56 12.4 7
0.6
1
10
CS401160T
TKY15T
10
1
1
CS401160T
TKY15T
10 100
50
32
32
45
78 14.4 8
1.7
10
CS401160T
TKY15T
12 125
63
40
32
56
89 16.4 9
10
CS401160T
TKY15T
16 160
63
40
29
56
120 16.4 9
5.4
10
CS401160T
TKY15T
20 200
24 250
63
63
60
60
32
32
130
180

175 25.7 14.22 8.1

210 25.7 14.22 11.8
10
3
3
CS401160T
TKY15T
CS401160T
TKY15T
6
8
s
s
10
10

Coated
Order Number
SONX1206PER
Class
Honing
MC5020
Shape
Work Material
N E
Geometry
(mm)
Ductile Cast Iron

6.3
Insert Grade

(SFM)
(inch/tooth)
985
(820 1150)
.016
(.012 .020)
720
(490 985)
.012
(.008 .016)
450MPa
655
(490 820)
.012
(.008 .016)
500 800
MPa
555
(490 655)
.008
(.004 .012)
200MPa
Gray Cast Iron
12.7
Tensile
Strength
250 350
MPa
MC5020
SPARE PARTS
M001
TECHNICAL DATA
N001
MILLING
INSERTS
K021
MILLING
SHOULDER MILLING
ASX400
<GENERAL CUTTING>
Light Alloy
Cast Iron
Finishing
Roughing
Fig.1
Fig.2
a Economical due to the

a Low resistance due to
Fig.3
the 3D design of
the curved cutting edge.
high rigidity holder.
C H :0
T :-9 -11
A.R :+11
R.R :-9 -11 I :+11
ASX400R0203
2504
0304C
0405E
0506E
0608E
0810M
1012M
Fine Pitch
Coarse Pitch
Order Number
Extra Fine Pitch
MILLING
Number
of Teeth
Type
y ARBOR TYPE
Stock
Dimensions (inch)
Max. Depth Mass

of Cut
(lbs)
ap
Type
(Fig.)
D1
L1
D9
L7
D8
W1
L8
2.000
1.575
.750
.748
.415
.313
.187
2.500
1.575
.750
.748
.415
.313
.187
.394
1.1
3.000
1.969
1.000
1.024
1.496
.375
.219
.394
2.2
4.000
1.969
1.500
1.378
2.362
.625
.375
.394
3.3
5.000
2.480
1.500
1.378
2.362
.625
.375
.394
5.5
6.000
2.480
1.500
1.378
2.362
.625
.375
.394
8.8
10
8.000
2.480
2.500
1.378
5.315
1.000
.560
.394
15.0
12
10.000
2.480
2.500
1.378
7.087
1.000
.560
.394
26.0
ASX400R0204
2.000
1.575
.750
.748
.415
.313
.187
.394
.8
2505
2.500
1.575
.750
.748
.415
.313
.187
.394
1.1
0306C
3.000
1.969
1.000
1.024
1.496
.375
.219
.394
2.2
0407E
4.000
1.969
1.500
1.378
2.362
.625
.375
.394
3.3
0508E
5.000
2.480
1.500
1.378
2.362
.625
.375
.394
5.5
0612E
12
6.000
2.480
1.500
1.378
2.362
.625
.375
.394
8.8
0816M
16
8.000
2.480
2.500
1.378
5.315
1.000
.560
.394
15.0
1018M
18
10.000
2.480
2.500
1.378
7.087
1.000
.560
.394
26.0
ASX400R0205
2.000
1.575
.750
.748
.415
.313
.187
.394
.8
2506
2.500
1.575
.750
.748
.415
.313
.187
.394
1.1
0308C
3.000
1.969
1.000
1.024
1.496
.375
.219
.394
2.2
0410E
10
4.000
1.969
1.500
1.378
2.362
.625
.375
.394
3.3
0512E
12
5.000
2.480
1.500
1.378
2.362
.625
.375
.394
5.5
0615E
15
6.000
2.480
1.500
1.378
2.362
.625
.375
.394
8.8
0819M
19
8.000
2.480
2.500
1.378
5.315
1.000
.560
.394
15.0
1022M
22
10.000
2.480
2.500
1.378
7.087
1.000
.560
.394
26.0
.394
.8
SPARE PARTS
Tool Holder Number
ASX400R Type
Shim
Shim Screw
Insert Screw
Wrench (Insert)
Wrench (Shim)
Insert
STASX400N
WCS503507H
TPS35
TIP15T
HKY35R
SOpT12T3pp
PEpR-pp

K022
Stock
Order Number
a
a
D1
L1
D4
L2
Shim
ap
3 1.500 4.750 1.250 1.500 .394 STASX400N WCS503507H TPS35 TIP15T HKY35R
4 2.000 4.750 1.250 1.575 .394 STASX400N WCS503507H TPS35 TIP15T HKY35R
SOpT12T3pp
PEpR-pp

Steel
: Stable Cutting
: General Cutting
: Unstable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
Honing :
E : Round F : Sharp
Hardened Materials
JH breaker SOMT12T308PEER-JH M E
.500
.156
.055
.031
.500
.156
.055
.031
.500
.156
.055
.031
.500
.156
.020
.079
.500
.156
.055
.031
HTi10
MC5020
FT breaker SOMT12T320PEER-FT M E
JP breaker SOGT12T308PEFR-JP
NX4545
JM breaker SOMT12T308PEER-JM M E
VP30RT
E E
Dimensions (inch)
Cermet Carbide
VP15TF
JL breaker SOET12T308PEER-JL
F7030
Order Number
Coated
G F
D1
S1
F1
Re
Geometry
MILLING
F7010
P
M
K
N
S
H
Class
Honing
For Aluminum Heavy Interrupted MediumHeavy LightSemi FinishLight

Application
-Heavy Cutting
Cutting
Alloy
Cutting
Cutting
Shape
Insert
Shim Screw
INSERTS
Work Material
Dimensions (inch)
Insert Wrench Wrench

Screw (Insert) (Shim)
a 2 1.250 4.750 1.250 1.500 .394 STASX400N WCS503507H TPS35 TIP15T HKY35R
R
ASX400R202W20
243W20
324W20
Number of Teeth
y WELDON SHANK TYPE
WIPER INSERTS
Dimensions (inch)
WOEW12T308PEER8C
E E
12T308PETR8C
E T
NX2525
Order Number
Class
Honing
HTi05T
Carbide Cermet
Shape
L1
L2
S1
F1
Re
Geometry
.492 .520 .156 .315 .031
a
a
.492 .520 .156 .315 .031
SPARE PARTS
M001
TECHNICAL DATA
N001
K023
MILLING
Fig.1
Fig.2
Fig.3
Fig.4
METRIC Standard
For metric arbors
C H :0
A.R :+11
T :-9 -11
R.R :-9 -11 I :+11
Stock
Order Number
ASX400-050A03R
-063A04R
-080B04R
-100B05R
-125B06R
-160C08R
-200C10R
-250C12R
ASX400-050A04R
-063A05R
-080B06R
-100B07R
-125B08R
-160C12R
-200C16R
-250C18R
ASX400-050A05R
-063A06R
-080B08R
-100B10R
-125B12R
-160C15R
-200C19R
-250C22R
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
D1
L1
D9
L7
D8
D12
W1
L8
3
4
4
5
6
8
10
12
4
5
6
7
8
12
16
18
5
6
8
10
12
15
19
22
50
63
80
100
125
160
200
250
50
63
80
100
125
160
200
250
50
63
80
100
125
160
200
250
40
40
50
50
63
63
63
63
40
40
50
50
63
63
63
63
40
40
50
50
63
63
63
63
22
22
27
32
40
40
60
60
22
22
27
32
40
40
60
60
22
22
27
32
40
40
60
60
20
20
29
32
32
29
32
32
20
20
29
32
32
29
32
32
20
20
29
32
32
29
32
32
11
11
38
45
60
56
135
180
11
11
38
45
60
56
135
180
11
11
38
45
60
56
135
180
41
50
60
70
80
100
160
210
41
50
60
70
80
100
160
210
41
50
60
70
80
100
160
210
10.4
10.4
12.4
14.4
16.4
16.4
25.7
25.7
10.4
10.4
12.4
14.4
16.4
16.4
25.7
25.7
10.4
10.4
12.4
14.4
16.4
16.4
25.7
25.7
6.3
6.3
7
8
9
9
14.22
14.22
6.3
6.3
7
8
9
9
14.22
14.22
6.3
6.3
7
8
9
9
14.22
14.22
Max. Depth Mass

of Cut
(kg)
ap
Dimensions (mm)
0.3
0.5
0.9
1.4
2.3
3.6
6.3
10.8
0.3
0.5
0.9
1.4
2.2
3.5
6.2
10.7
0.3
0.5
0.9
1.4
2.1
3.4
6.2
10.5
1
1
2
2
2
3
4
4
1
1
2
2
2
3
4
4
1
1
2
2
2
3
4
4
ap
Re
METRIC Standard
L3
L1
Stock
Order Number
Fine Pitch Coarse Pitch
ASX400R403S32
503S32
634S32
804S32
ASX400R504S32
635S32
806S32
s
s
s
s
s
s
s
Number of Teeth
Type
y SHANK TYPE
K024
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
Type
(Fig.)
D4
MILLING
D1
Number
of Teeth
Extra Fine Pitch
Fine Pitch
Coarse Pitch
Type
y ARBOR TYPE
D1
L1
D4
L3
ap
Shim
Shim Screw
3
3
4
4
4
5
6
40
50
63
80
50
63
80
125
125
125
125
125
125
125
32
32
32
32
32
32
32
40
40
40
40
40
40
40
10
10
10
10
10
10
10
STASX400N
STASX400N
STASX400N
STASX400N
STASX400N
STASX400N
STASX400N
WCS503507H
WCS503507H
WCS503507H
WCS503507H
WCS503507H
WCS503507H
WCS503507H
Dimensions (mm)
Clamp Torque (lbf-in) : WCS503507H=44, TPS35=31

*
Insert
Screw
TPS35
TPS35
TPS35
TPS35
TPS35
TPS35
TPS35
Wrench
(Insert)
TIP15T
TIP15T
TIP15T
TIP15T
TIP15T
TIP15T
TIP15T
Wrench
Insert
(Shim)
HKY35R
HKY35R SOpT12T3pp
PEpR-pp
HKY35R
HKY35R
HKY35R
SOpT12T3pp
HKY35R
PEpR-pp
HKY35R
Fig.1
Fig.2
METRIC Standard
For inch arbors
Fine Pitch
Coarse Pitch
Type
y ARBOR TYPE
Number
of Teeth
C H :0
A.R :+11
T :-9 -11
R.R :-9 -11 I :+11
D1
4
5
80
100
50
50
125
63
25.4 [1.0"]
31.75 [1.25"]
38.1 [1.5"]
160
63
50.8
10
12
200
250
63
63
6
7
80
100
50
50
125
63
25.4 [1.0"]
31.75 [1.25"]
38.1 [1.5"]
12
160
63
50.8
16
18
200
250
63
63
Stock
Order Number
ASX400R08004C
R10005D
R12506E
R16008F
R20010K
R25012K
ASX400R08006C
R10007D
R12508E
R16012F
R20016K
R25018K
s
s
s
L1
Max. Depth
of Cut
ap
Mass
(kg)
Type
(Fig.)
10
10
1.0
1.5
1
1
Dimensions (mm)
[inch]
D9
L7
D8
D12
W1
26
32
38
45
60
70
9.5
12.7
35
60
80
15.9
10
10
2.5
[2.0"]
47.625 [1.875"]
47.625 [1.875"]
38
90
100
19.1
11
10
4.0
35
135
180
160
210
25.4
25.4
14.22
14.22
10
10
7.0
12.0
2
2
26
32
38
45
60
70
9.5
12.7
10
10
1.0
1.5
1
1
35
60
80
15.9
10
10
2.5
[2.0"]
47.625 [1.875"]
47.625 [1.875"]
38
90
100
19.1
11
10
4.0
35
135
180
160
210
25.4
25.4
14.22
14.22
10
10
7.0
12.0
2
2
35
35
L8
6
8
6
8
Section A-A
METRIC Standard
y SCREW-IN TYPE
Mass
Number of Teeth
Stock
Coolant Thru
Order Number
MILLING
(Max. Depth of Cut)
Dimensions (mm)
2
* (kg)
D1 D4 D5 L1 L2 L11 H1 M
Shim
Shim
Screw
Insert
Screw
Wrench
(Insert)
Wrench
(Shim)
ASX400R322AM1640
s u
2 32 17 29 63 40
24 M16 0.3
WCS503507H
TPS35
TIP15T
HKY35R
403AM1645
s u
3 40 17 29 68 45
24 M16 0.3 STASX400N WCS503507H
TPS35
TIP15T
HKY35R
Torque (lbf-in) : WCS503507H=44, TPS35=31

*12 Clamp
Clamp Torque of the Head (lbf-ft) : M16=66.7
*
SCREW-IN ARBORS
K142
SPARE PARTS
M001
INSERTS
K023
TECHNICAL DATA
N001
K025
MILLING
Work Material
Grade
Cutting Speed
(SFM)
FinishMedium Cutting LightSemi-Heavy Cutting MediumHeavy Cutting

Feed per Tooth (inch/tooth) Breaker Feed per Tooth (inch/tooth) Breaker Feed per Tooth (inch/tooth) Breaker
F7030
920 (690 1150)
.007 (.003 .011)
JL
.008 (.004 .012)
JM
.010 (.008 .014)
JH
VP15TF
820 (655 985)
.007 (.003 .011)
JL
.008 (.004 .012)
JM
.010 (.004 .014)
JH
VP30RT
755 (590 920)
.007 (.003 .011)
JL
.008 (.004 .012)
JM
.010 (.004 .014)
JH
NX4545
590 (425 755)
.006 (.003 .009)
JL
.007 (.004 .011)
JM
F7030
820 (655 985)
.006 (.003 .009)
JL
.007 (.004 .011)
JM
.008 (.004 .012)
JH
VP15TF
720 (560 885)
.006 (.003 .009)
JL
.007 (.004 .011)
JM
.008 (.004 .012)
JH
VP30RT
490 (395 590)
.005 (.002 .008)
JL
.006 (.004 .010)
JM
NX4545
490 (390 590)
.005 (.002 .008)
JL
.006 (.004 .010)
JM
F7030
590 (425 755)
.005 (.002 .008)
JL
.006 (.004 .010)
JM
.007 (.004 .011)
JH
VP15TF
460 (330 590)
.005 (.002 .008)
JL
.006 (.004 .010)
JM
.007 (.004 .011)
JH
VP30RT
390 (260 525)
.005 (.002 .008)
JL
.006 (.004 .010)
JM
.007 (.004 .011)
JH
NX4545
330 (260 395)
.004 (.002 .006)
JL
.005 (.004 .008)
JM
VP15TF
720 (560 885)
.006 (.003 .009)
JL
.007 (.004 .011)
JM
.008 (.004 .012)
JH
VP30RT
490 (395 590)
.006 (.003 .009)
JL
.007 (.004 .011)
JM
NX4545
490 (390 590)
.006 (.003 .009)
JL
.007 (.004 .011)
JM
Hardness
P
Mild Steel
< 180HB
180 280HB
Carbon Steel
Alloy Steel
280 350HB
M
Stainless Steel
K
Cast Iron
< 270HB
Tensile Strength
< 450MPa
Hardened Steel
655 (490 820)
.008 (.004 .012)
JM
.010 (.004 .014)
VP15TF
590 (425 820)
.007 (.004 .011)
JL
.008 (.004 .012)
JM
.010 (.004 .014)
JH
2130 (1000 3300) .006 (.004 .008)
JP
.008 (.004 .012)
JP
.012 (.008 .016)
JP
HTi10
VP15TF
130 (65 165)
.006 (.003 .008)
JL
.008 (.004 .012)
JM
40 55HRC
VP15TF
200 (120 280)
.003 (.002 .005)
JL
.004 (.002 .006)
JM
.005 (.003 .007)
JH
Aluminum Alloy

H
MC5020
JH
FT
MILLING
INSTRUCTIONS FOR USING INSERTS
K026
y INSTRUCTIONS FOR USE OF THE JP BREAKER

a The JP breaker has sharp cutting edges.
Wear gloves when handling.
y INSTRUCTIONS FOR USE OF WIPER INSERTS

a Wiper inserts for the ASX400 are
single-cornered.
a When machining aluminum alloy, welding to
a When installing the wiper insert, place the
the cutting edge tends to occur, often leading

to insert failure. To prevent this, wet cutting is
recommended.
insert so that the small chamfer is located

as shown.
FEATURES
y ECONOMICAL
y LOW RESISTANCE
y HIGH ACCURACY
ASX400 is economical as it employs
Due to the 3D design of the cutting edge and a

large rake angle, high cutting edge sharpness has
been achieved with reduced cutting resistance.
Due to the curved edge and high accuracy

body and insert, high accuracy surface
nish on walls and high quality surface
nish on faces can be achieved.
inserts that have 4 cutting edges. Additionally

with one tool, it is possible to carry out face
milling, shoulder milling, and slotting operations.
*JM breaker data

.276" pitch x 3
Tool
ASX400
.0012
Competitor A
.0040
Competitor B
.0048
Values obtained under

recommended cutting
conditions.
Wall accuracy (inch)
Cutting edge diameter
y EASY TO USE
y HIGH RELIABILITY
y HIGH HEAT-RESISTANT BODY
Employs a screw on type mechanism,

therefore, the inserts can be easily set.
Additionally when indexing the insert, it is not
necessary to remove the screw completely.
Uses a carbide shim and Mitsubishi's proprietary

Anti-Fly-Insert (A.F.I) to prevent the inserts from
moving when machining. Additionally the insert
screw uses TORXPLUS, for high clamping
force ensuring high reliability.
The cutter body is made from a special alloy that

provides high strength at high temperatures. A
special surface treatment improves the corrosion
and friction resistance. The ASX400 can be
used for long hours even under harsh conditions.
re
eratu
mp
of te
t pro
Hea
Conv
ention
al
1.7
tim
es
y CHIPBREAKERS FOR A WIDE RANGE OF APPLICATIONS
JM
Light to SemiHeavy cutting

Breaker
a High accuracy insert
a High accuracy M class
with ground-nished
periphery.
a Large rake angle
leading to low cutting
resistance.
insert.
a For a wide range of
workpiece materials
and cutting conditions.
JH
Medium to
Heavy cutting
Breaker
FT
Heavy cutting/
Heavy interrupted cutting
Breaker
JP
Aluminum alloy
cutting
Breaker

a High accuracy insert
insert.
insert.
with ground-nished
periphery.
a Strong cutting edge for
a Corner radius of .079" has
high fracture resistance.
improved fracture resistance. a Large rake angle and
mirror-nished rake face
a Strong main cutting edge
allows heavy cutting and
lead to sharp cutting
heavy interrupted cutting.
performance and high
Stable cutting performance.
welding resistance.
MILLING
JL
Finish to
Light cutting
Breaker
y INSERT GRADES FOR A WIDE RANGE OF MATERIALS

Stainless Steel
Cast Iron
Ductile Cast Iron
Aluminum Alloy
Heat Treated Steel
Cutting Unstable
Stable Conditions
Cutting Unstable
Stable Conditions
Cutting Unstable
Stable Conditions
Cutting Unstable
Stable Conditions
Cutting Unstable
Stable Conditions
Low
Cutting
Speed
High
Carbon Steel
Alloy Steel
Cutting Unstable
Stable Conditions
(Note) When machining steel or stainless steel where the emphasis is on surface nish, use cermet grade NX4545.
Stable Cutting : Continuous cutting, Constant depth of cut, Pre-machined securely clamped component cutting
Unstable Cutting : Heavy interrupted, Irregular depth of cut, Low clamping rigidity cutting
K027
MILLING
SHOULDER
MILLING
<GENERAL AND HEAVY CUTTING>
NSE300,400
Light Alloy
Cast Iron
Finishing
Roughing
Fig.1
Fig.2
a High rake angle.
a Enables highly
Fig.3
efcient machining.
Type
C H :0
A.R :+16
T :+5 +8
R.R :+5 +8 I :+16
Stock Number
R of Teeth
Order Number
NSE400
NSE300
NSE300R0204
2505
0304C
0306C
0405E
0408E
NSE400R0306C
0407E
0508E
0610F
0812M
a
a
a
a
a
a
a
a
a
a
a
4
5
4
6
5
8
6
7
8
10
12
Dimensions (inch)
D1
L1
D9
L7
D8
W1
L8
Max. Depth
of Cut
ap
2.000
2.500
3.150
3.150
3.937
3.937
3.150
3.937
4.921
6.299
7.874
1.575
1.575
1.969
1.969
2.480
2.480
1.969
2.480
2.480
2.480
2.480
.750
.750
1.000
1.000
1.500
1.500
1.000
1.500
1.500
2.000
2.500
.748
.748
1.024
1.024
1.181
1.181
1.024
1.181
1.496
1.496
1.378
.415
.415
.512
.512
.787
.787
.512
.787
2.362
3.150
5.512
.313
.313
.375
.375
.625
.625
.375
.625
.625
.750
1.000
.187
.187
.219
.219
.375
.375
.219
.375
.375
.437
.560
.492
.492
.492
.492
.492
.492
.669
.669
.669
.669
.669
Mass
(lbs)
Type
(Fig.)
.8
1.3
2.8
2.4
5.2
4.6
2.4
4.6
7.0
11.8
17.0
1
1
1
1
1
1
1
1
2
2
3
SPARE PARTS
*
Tool Holder
Number
z
Locator Wedge-T Locator Wedge-T
NSE300R0204
2505
SPTSE300R
LS19T
TKY15T
TS32
LS10T
NSE300R0408E
NSE400R Type
Work
Material
Hardness
P
Mild Steel
Grade

(SFM)
(inch/tooth)
F7010
785
(525 950)
< 180HB
VF15TF
F7010/F7030
590
(330 820)
655
(440 785)
Carbon Steel < 180280HB

Alloy Steel
NX4545
460
(260 655)
280350HB
VP15TF
390
(260 525)

a
r
Stainless
Steel
Grade
< 200HB
VP15TF
490
(330 655)
MC5020
655
(440 785)
VP15TF
525
(330 720)
HTi10
2600
(1800 3200)
Tensile
Cast Iron Strength
< 350MPa
N Aluminum
Alloy

(SFM)
(inch/tooth)
Hardness
.006
(.004 .008)
TKY25T
SPTSE400R CWSE300TR LS10TS
Work
Material
.008
(.004 .012)
.008
(.004 .012)
TKY08F
* Clamp Torque (lbf-in) : LS19T=44, LS10T=75, LS10TS=75
K028
Locator Wrench Wrench

Screw (Clamp Screw) (Locator Screw)

CWNSE300TR
MILLING
NSE300R0304C
Insert
CWTSE300TR
Clamp
Screw
.008
(.004 .012)
.008
(.004 .012)
.005
(.002 .008)
INSERTS
: Stable Cutting
Stainless Steel
Cast Iron
Non-Ferrous Metal
32PESR1
E S
r
a
HTi10
NX4545
E T
UTi20T
32PETR1
UP20M
Cermet Carbide
NX2525
E E
VP15TF
32PEER1
MC5020
E F
F7010
TEEN32PEFR1
F7030
Coated
D1
S1
F1
Re
.375 .125 .055 .016
.375 .125 .055 .016
.375 .125 .055 .016
TECN32PEFR1W C F
.375 .125 .055 .016
32PEER1W C E
.375 .125 .055 .016
.500 .187 .055 .039
43PEER1
C E
.500 .187 .055 .039
43PETR1
C T
TEEN43PEFR1
E F
43PEER1
E E
43PETR1
E T
NSE400
C F
43PESR1
E S
TEKN43PEER1
K E
43PETR1
K T
43PESR1
K S
43PETR
K T
43PEZR
K Z
a
a
.500 .187 .055 .039
a
a
Curved edge
.375 .125 .055 .016
TECN43PEFR1
Geometry
.375 .125 .055 .016
: Unstable Cutting
Dimensions (inch)
32PETR1W C T
: General Cutting
Honing : E : Round F : Sharp S : Chamfer + Round

T : Chamfer Z : Strong
Order Number
Shape
For improved
wall accuracy
Steel
Class
Honing
NSE300
Cutter Type
Work Material
P
M
K
N
.500 .187 .055 .039
.500 .187 .055 .039

.500 .187 .055 .039
.500 .187 .055 .039
s
s
s
s
s
s
.500 .187 .076
.500 .187 .076
.500 .187 .076
.500 .187 .076
.500 .187 .076
Strong cutting edge type.

: Stable Cutting
Honing : E : Round
Stainless Steel
Cast Iron
TEER32PEER-JS
E E
JS breaker
TEER43PEER-JS
E E
UTi20T
F7030
JS breaker
NX2525
Order Number
F7010
Shape
: General Cutting
: Unstable Cutting
MILLING
Steel
Class
Honing
P
M
K
Dimensions (inch)
D1
S1
F1
Re
.375 .125 .055 .016
.500 .187 .055 .039
Geometry
NSE300
Cutter Type
Work Material
NSE400
SPARE PARTS
M001
TECHNICAL DATA
N001
K029
MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
Finishing
Roughing
APX3000
Light Alloy
Cast Iron
Fig.1

Max. Depth of Cut
Fig.2
Max. Depth of Cut
Fig.3
a Low resistance insert
and high rigidity body.
Max. Depth of Cut

a High wall accuracy can be
Fig.4
produced by using this cutter

and unique insert geometry.
Max. Depth of Cut
y SHANK TYPE
A Holders
.079
Standard
.094
B Holders
MILLING
K030
.008
.125
.500
.500
.625 3.250 1.120

.500 3.250 1.120
6
6
TIP07F
Anti-seize
Lubricant
MK1KS
1
1
Insert
Screw
TPS25
TPS25
TIP07F
MK1KS
.625
.625 3.625 1.190
16
TPS25
TIP07F
MK1KS
.625
.625 3.625 1.190
16
TPS25
TIP07F
MK1KS
.750
.750 4.375 1.380
TPS25
TIP07F
MK1KS
.750
.750 4.375 1.380
TPS25
TIP07F
MK1KS
.750
.750 4.375 1.380
TPS25
TIP07F
MK1KS
.750
.750 4.375 1.380
TPS25
TIP07F
MK1KS
3 1.000
.750 4.375 1.570
TPS25 1
TIP07F
MK1KS
3 1.000
.750 4.375 1.570
TPS25 1
TIP07F
MK1KS
4 1.000
.750 4.375 1.570
TPS25 1
TIP07F
MK1KS
4 1.000
.750 4.375 1.570
TPS25 1
TIP07F
MK1KS
3 1.000 1.000 4.750 1.570
TPS25 1
TIP07F
MK1KS
3 1.000 1.000 4.750 1.570
TPS25 1
TIP07F
MK1KS
APX3000UR081FA10SA
081SA08SA
102FA10SA
102SA10SA
122FA12SA
122SA12SA
123FA12SA
123SA12SA
163FA12SA
163SA12SA
164FA12SA
164SA12SA
163FA16SA
163SA16SA
164FA16SA
164SA16SA
205FA20SA
205SA20SA
246FA20SA
246SA20SA
APX3000UR081SA08SB
102SA10SB
122SA12SB
123SA12SB
163SA12SB
164SA12SB
163SA16SB
164SA16SB
205SA20SB
246SA20SB
Clamp Torque (lbf-in) : TPS25=8.9, TPS25 1=8.9

a
D1
Stock
Order Number
Number of Teeth
Insert
Corner
Re
Type
Dimensions(inch)
D4
L1
L2
Max.
Ramping Type
Angle (Fig.)
%
*
Wrench
4 1.000 1.000 4.750 1.570
TPS25 1
TIP07F
MK1KS
4 1.000 1.000 4.750 1.570
TPS25 1
TIP07F
MK1KS
5 1.250 1.250 5.125 1.970
TPS25 1
TIP07F
MK1KS
5 1.250 1.250 5.125 1.970
TPS25 1
TIP07F
MK1KS
6 1.500 1.250 5.125 1.970

6 1.500 1.250 5.125 1.970
2
2
TPS25 1
TIP07F
MK1KS
TPS25 1
TIP07F
MK1KS
.500
.625
.500 3.250 1.120

.625 3.625 1.190
6
16
TPS25
TIP07F
MK1KS
1
2
TPS25
TIP07F
MK1KS
.750
.750 4.375 1.380
TPS25
TIP07F
MK1KS
.750
.750 4.375 1.380
TPS25
TIP07F
MK1KS
3 1.000
.750 4.375 1.570
TPS25 1
TIP07F
MK1KS
4 1.000
.750 4.375 1.570
TPS25 1
TIP07F
MK1KS
3 1.000 1.000 4.750 1.570
TPS25 1
TIP07F
MK1KS
4 1.000 1.000 4.750 1.570
TPS25 1
TIP07F
MK1KS
5 1.250 1.250 5.125 1.970

6 1.500 1.250 5.125 1.970
3
2
TPS25 1
TIP07F
MK1KS
TPS25 1
TIP07F
MK1KS
a
a
A Holders
Long
.079
.094
.125
Stock
Dimensions(inch)
Max.
Ramping Type
Angle (Fig.)
%
9
5
TIP07F
Anti-seize
Lubricant
MK1KS
2 .750 .750 7.250 1.380

2 1.000 1.000 8.500 1.570
Insert
Screw
TPS25
TPS25 1
TIP07F
MK1KS
3 1.000 1.000 8.500 1.570
TPS25 1
TIP07F
MK1KS
3 1.250 1.250 9.000 1.970
TPS25 1
TIP07F
MK1KS
4 1.250 1.250 9.000 1.970
TPS25 1
TIP07F
MK1KS
TIP07F
MK1KS
APX3000UR122SA12LA
162SA16LA
163SA16LA
203SA20LA
204SA20LA
243SA20LA
244SA20LA
APX3000UR122SA12LB
162SA16LB
163SA16LB
203SA20LB
204SA20LB
243SA20LB
244SA20LB
.008
B Holders
D1
D4
L1
L2
Wrench
3 1.500 1.250 9.000 1.970

4 1.500 1.250 9.000 1.970
2
2
TPS25 1
TPS25 1
TIP07F
MK1KS
9
5
TPS25
TIP07F
MK1KS
2 .750 .750 7.250 1.380

2 1.000 1.000 8.500 1.570
TPS25 1
TIP07F
MK1KS
3 1.000 1.000 8.500 1.570
TPS25 1
TIP07F
MK1KS
a
a
a
3 1.250 1.250 9.000 1.970
TPS25 1
TIP07F
MK1KS
4 1.250 1.250 9.000 1.970
TPS25 1
TIP07F
MK1KS
3 1.500 1.250 9.000 1.970

4 1.500 1.250 9.000 1.970
2
2
TPS25 1
TIP07F
MK1KS
TPS25 1
TIP07F
MK1KS
Max. Depth of Cut
Order Number
Number of Teeth
Insert
Corner
Re
Type

.094
A Holders
B Holders
.079
.125
APX3000R0205A
0207A
2506A
0306A
0309A
APX3000R0205B
0207B
2506B
0306B
0309B
T :+15 +27
I :+7 +21
Dimensions (inch)
D1
L1
D9
L7
.750
.750
D8
D12
W1
L8
Insert Wrench Anti-seize Coolant thru

D11 % Screw
Lubricant Set Bolt
.600 1 TPS251 TIP07F MK1KS HSCU37513H
5 2.000 1.575
7 2.000 1.575
.748 .415 1.811 .313

.748 .415 1.811 .313
.187
.187
6 2.500 1.969 1.000 1.024 .539 2.360 .375
.219

6 3.000 1.969 1.000 1.024 .539 2.756 .375

9 3.000 1.969 1.000 1.024 .539 2.756 .375
.219
.219

5 2.000 1.575
7 2.000 1.575
.748 .415 1.811 .313

.748 .415 1.811 .313
.187
.187

6 2.500 1.969 1.000 1.024 .539 2.360 .375
.219
6 3.000 1.969 1.000 1.024 .539 2.756 .375

9 3.000 1.969 1.000 1.024 .539 2.756 .375
.219
.219

a
a
.750
.750
MILLING
Re
.008
Stock
Order Number
Number of Teeth
Insert Corner
Type
y ARBOR TYPE
Max. Ramping Angle
C H :0
A.R :+7 +21
R.R :+15 +27
* Clamp Torque (lbf-in) : TPS25 1=8.9

y COMBINATION OF HOLDER AND INSERT CORNER RADIUS
A Holder
B Holder
APX3000URooooooA
APX3000URooooooB
Holder
Insert Corner Radius

(Re)
INSERTS
K035
SPARE PARTS
M001
OPERATION GUIDANCE
K049
TECHNICAL DATA
N001
K031
MILLING
Fig.1
10 (Max. Depth of Cut)
Fig.2
Fig.3
METRIC Standard
.008
.079
.008
.079
.008
Long
Extra Long
MILLING
Standard
Re
(inch)
.079
APX3000R121SA16SA
141SA16SA
162SA16SA
182SA16SA
202SA20SA
203SA20SA
223SA20SA
252SA25SA
253SA25SA
254SA25SA
284SA25SA
304SA32SA
323SA32SA
324SA32SA
325SA32SA
403SA32SA
405SA32SA
406SA32SA
507SA32SA
638SA32SA
APX3000R182SA16LA
202SA20LA
222SA20LA
252SA25LA
253SA25LA
282SA25LA
283SA25LA
322SA32LA
323SA32LA
352SA32LA
353SA32LA
APX3000R182SA16ELA
202SA20ELA
222SA20ELA
252SA25ELA
253SA25ELA
282SA25ELA
283SA25ELA
322SA32ELA
323SA32ELA
352SA32ELA
353SA32ELA
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Number of Teeth
Order Number
Stock
Insert Corner
Type
y STRAIGHT SHANK TYPE (A Holders)
D1
D4
L1
L2
1
1
2
2
2
3
3
2
3
4
4
4
3
4
5
3
5
6
7
8
2
2
2
2
3
2
3
2
3
2
3
2
2
2
2
3
2
3
2
3
2
3
12
14
16
18
20
20
22
25
25
25
28
30
32
32
32
40
40
40
50
63
18
20
22
25
25
28
28
32
32
35
35
18
20
22
25
25
28
28
32
32
35
35
16
16
16
16
20
20
20
25
25
25
25
32
32
32
32
32
32
32
32
32
16
20
20
25
25
25
25
32
32
32
32
16
20
20
25
25
25
25
32
32
32
32
85
85
85
85
100
100
115
115
115
115
115
125
125
125
125
125
125
125
125
125
120
150
150
170
170
170
170
190
190
190
190
180
200
200
220
220
220
220
260
260
260
260
25
25
25
25
30
30
30
35
35
35
35
45
45
45
45
45
45
45
45
45
25
60
30
70
70
35
35
90
90
45
45
25
70
30
80
80
35
35
100
100
45
45
6
6
15
11
9
9
7
6
6
6
4
4
3
3
3
2
2
2
1
1
11
9
7
6
6
4
4
3
3
3
3
11
9
7
6
6
4
4
3
3
3
3
Max.
Ramping Type
Angle (Fig.)
Dimensions (mm)
1
1
2
3
2
2
3
2
2
2
3
2
2
2
2
3
3
3
3
3
3
2
3
2
2
3
3
2
2
3
3
3
2
3
2
2
3
3
2
2
3
3
*
Insert
Screw
TPS25
TPS25
TPS25
TPS25
TPS25
TPS25
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS25
TPS25
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS25
TPS25
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
Wrench Anti-seize
Lubricant
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
(Note) When using inserts with corner radius Re >.094" (2.4mm), B-Holders are required as shown on page K035.
*
K032
Insert
AOMT
1236pp
PEER-p
AOGT
1236pp
PEFR-GM
METRIC Standard
C H :0
A.R :+7 +21
R.R :+15 +27
Number of Teeth
.008
.079
T :+15 +27
I :+7 +21
APX3000-032A05RA
32 40 16 18
9 30
-040A06RA
40 40 16 18
9 34
-050A07RA
50 40 22 20
-063A08RA
63 40 22 20
-080A09RA
80 50 27 23 13 70 12.4
-100A11RA
Order Number
Re
(inch)
Stock
Insert Corner
y ARBOR TYPE (A Holders)
Dimensions (mm)
D1
L1 D9 L7
Max. Ramping
Angle
For metric arbors
Wrench Anti-seize
Lubricant
Coolant thru
Set Bolt
Insert
Screw
TPS25 1
TIP07F
MK1KS
HSC08030H
TPS25 1
TIP07F
MK1KS
HSC08030H
TPS25 1
TIP07F
MK1KS
HSC10030H
L8
D11
8.4
5.6
14
8.4
5.6
14
11 45 10.4
6.3
17
D8 D12 W1
11 55 10.4
11 100 63 32 26 17 80 14.4
6.3
17
TPS25 1
TIP07F
MK1KS
HSC10030H
20
TPS25 1
TIP07F
MK1KS
HSC12035H
26
0.5 TPS25 1
TIP07F
MK1KS
HSC16040H
(Note) When using inserts with corner radius Re >.094"(2.4mm), B-Holders are required as shown on page K035.
Clamp Torque (lbf-in) : TPS25 1=8.9
C H :0
A.R :+7 +21
R.R :+15 +27
Stock
Order Number
Re
(inch)
R
s
R10011DA
.008 APX3000R08009CA
.079
Number of Teeth
Insert Corner
Dimensions (mm)
D1 L1
D9
80 50 25.4 [1.0"]
T :+15 +27
I :+7 +21
[inch]
L7 D8 D12 W1
26 13 70
Max. Ramping
Angle
For inch arbors
L8 D11 %
9.5 6 20 1
MILLING
METRIC Standard
*
Insert
Anti-seize Coolant thru
Screw Wrench Lubricant
Set Bolt
TPS25 1 TIP07F MK1KS HSC12035H
11 100 63 31.75 [1.25"] 32 17 80 12.7 8 26 0.5 TPS25 1 TIP07F
MK1KS
HSC16040H
(Note) When using inserts with corner radius Re >.094"(2.4mm), B-Holders are required as shown on page K035.
Clamp Torque (lbf-in) : TPS25 1=8.9
INSERTS
K035
OPERATION GUIDANCE
K049
SPARE PARTS
M001
TECHNICAL DATA
N001
K033
MILLING

H1
METRIC Standard
Section A-A
D4
D5
L1
L2
L11
H1
16
8.5
13
48
30
10
M8
0.1 TPS25
Wrench Anti-seize
Lubricant
TIP07F MK1KS
18
8.5
13
48
30
10
M8
0.1 TPS25
TIP07F
MK1KS
20
10.5
18
49
30
14
M10 0.1 TPS25
TIP07F
MK1KS
223M10A30
22
10.5
18
49
30
14
M10 0.1 TPS25 1 TIP07F
MK1KS
254M12A35
25
12.5
21
57
35
19
M12 0.2 TPS25 1 TIP07F
MK1KS
.079
284M12A35
28
12.5
21
57
35
19
M12 0.2 TPS25 1 TIP07F
MK1KS
304M16A40
30
17
29
63
40
24
M16 0.3 TPS25 1 TIP07F
MK1KS
325M16A40
32
17
29
63
40
24
M16 0.3 TPS25 1 TIP07F
MK1KS
355M16A40
35
17
29
63
40
24
M16 0.3 TPS25 1 TIP07F
MK1KS
406M16A40
40
17
29
63
40
24
M16 0.3 TPS25 1 TIP07F
MK1KS
APX3000R162M08A30
182M08A30
203M10A30
Mass
Stock
D1
Order Number
Re
(inch)
.008

1
Number of Teeth
Insert Corner
y SCREW-IN TYPE (A Holders)

Dimensions (mm)
M*
Insert
Screw
(kg)
Insert
AOMT
1236pp
PEER-p
AOGT
1236pp
PEFR-GM
1 Clamp Torque (lbf-in) : TPS25=8.9, TPS25 1=8.9

2 Clamp Torque of the Head (lbf-ft) : M8=17.1, M10=33.8, M12=59.2, M16=66.7
(Note) For large R inserts
APX offers various nose radii for inserts, however one holder can NOT secure every insert radius.
We offer A-Holders that properly secures up to .079" radius.
Customers may modify holders as below, so that larger nose radii can be secured.
*
*
NOTE ON USE OF INSERTS WITH LARGE CORNER RADII
MILLING
When using inserts with corner radius Re > R.094",

please machine the holder with a radius form as shown
on the right table.
R
.106"
(B-Holder)
R : Holder end radius

Re : Insert corner radius
R
Or B-Holders are available as non stock, produced to order only.
"Order numbers"; Please add "B" to the end of the order number of A-Holders.
Ex) APX3000R162M08A30APX3000R162M08A30B
K034
Re
.094"
.118"
.125"

Re
INSERTS
Dimensions (inch)
Stock
Coated Carbide
Order Number
General Use
M breaker
AOMT123602PEER-M
a a
.472 .260 .142 .071 .008
123604PEER-M
a a
.472 .260 .142 .063 .016
123608PEER-M
a a
.472 .260 .142 .047 .031
123610PEER-M
s s
.472 .260 .142 .039 .039
123612PEER-M
a a
.472 .260 .142 .031 .047
123616PEER-M
a a
.472 .260 .142 .016 .063
123620PEER-M
a a
.472 .260 .142 .016 .079
123624PEER-M
a a
.472 .260 .142 .016 .094
123630PEER-M
a a
.472 .260 .142 .016 .118
123632PEER-M
a a
.472 .260 .142 .016 .125
AOMT123604PEER-H
a a a
.472 .260 .142 .063 .016
123608PEER-H
a a a
.472 .260 .142 .047 .031
123612PEER-H
a a a
.472 .260 .142 .016 .063
Strong Cutting
Edge Type
H breaker
Aluminum
Alloy Machining
GM breaker
L1
L2
S1
F1
Geometry
Re
TF15
MC5020
VP15TF
VP20RT
Shape
AOGT 123602PEFR-GM
.472 .260 .142 .071 .008
123604PEFR-GM
.472 .260 .142 .063 .016
123608PEFR-GM
.472 .260 .142 .047 .031

We offer B-Holders that secures .094", .118" and .125" radius, only for popular inch sizes.

on the right table.
Re
.094"
.118"
.125"
.106"
(B-Holder)
MILLING
R : Holder end radius

Re : Insert corner radius
Or additional B-Holders are available as non stock, produced to order only.
"Order numbers"; Please replace the last letter "A" of A-Holders to "B".
Ex) APX3000R08009CAAPX3000R08009CB
OPERATION GUIDANCE
K049
SCREW-IN ARBORS
K142
SPARE PARTS
M001
TECHNICAL DATA
N001
K035
MILLING
APX3000
y CUTTING CONDITIONS FOR SHOULDER MILLING
Work Material
Hardness
Insert
Grade
Mild Steel
< 180HB
Cutting
Speed
vc
(SFM)
Width
of Cut
ae
(inch)
755
(600 900)
.25D1
VP15TF
VP20RT
720
M breaker (
570 860)
590
(470 700)
< 270HB
Gray Cast Iron
MILLING
Ductile Cast Iron
.006
.004
.157
.004
.157
.157 .276
.006
.004
.078
.078 .197
.006
.004
.157
.004
.157
.157 .276
.006
.004
.078
.078 .197
.006
.004
.157
.004
.157
.157 .276
.006
.004
.078
.078 .197
.006
.004
.157
.004
.157
.157 .276
.004
.003
.078
.078 .197
.004
.003
.157
.003
.157
.157 .276
.157
.157 .276
.75D1
.25D1
.75D1
.5D1
460
(395 525)
.75D1
590
(470 700)
.25D1
560
(440 670)
.5D1
460
(395 525)
.75D1
MC5020
820
H breaker (655 985)
.25D1
VP20RT
M breaker
.5D1
690
MC5020
H breaker (525 850)
.75D1
MC5020
655
H breaker (490 820)
.25D1
620
MC5020
H breaker (460 785)
.5D1
555
MC5020
H breaker (390 720)
.75D1
.25D1
Aluminum Alloy
TF15
1640
GM breaker (655 3280)
295
(230 350)
Hardened Steel 4055HRC
K036
.078
.078 .197
.5D1
560
(440 670)
Tensile
Strength
785
MC5020
< 350MPa
H breaker (625 950)
Tensile
Strength
< 800MPa
.006
.004
.25D1
Stainless Steel
.157
.157 .276
590
(440 670)
VP15TF
Carbon Steel
180350HB
M breaker
Alloy Steel
VP15TF
280
H breaker (
200 330)
230
(180 270)
& .500"
& .625" & 1.000"
& 1.250" & 3.000"
(& 12mm)
(& 16mm & 25mm)
(& 32mm & 80mm)
Depth of Cut Feed per Tooth Depth of Cut Feed per Tooth Depth of Cut Feed per Tooth
ap
ap
ap
fz
fz
fz
(inch)
(inch)
(inch)
(IPT)
(IPT)
(IPT)
.5D1
.5D1
.75D1
.006
.004
.006
.004
.197
.197 .276
.276 .335
.335 .394
.118
.118 .217
.217 .315
.315 .394
.157
.157 .394
.197
.197 .276
.276 .335
.335 .394
.118
.118 .217
.217 .315
.315 .394
.157
.157 .394
.197
.197 .276
.276 .335
.335 .394
.118
.118 .217
.217 .315
.315 .394
.157
.157 .394
.197
.197 .276
.276 .335
.335 .394
.118
.118 .217
.217 .315
.315 .394
.157
.157 .394
.197
.197 .276
.276 .335
.335 .394
.118
.118 .217
.217 .315
.315 .394
.157
.157 .394
.157
.157 .276
.157
.157 .276
.010
.008
.006
.004
.010
.008
.006
.004
.006
.004
.010
.008
.006
.004
.010
.008
.006
.004
.006
.004
.008
.006
.004
.003
.008
.006
.004
.003
.004
.003
.010
.008
.006
.004
.010
.008
.006
.004
.006
.004
.008
.006
.004
.003
.008
.006
.004
.003
.004
.003
.010
.006
.008
.004
.197
.197 .276
.276 .335
.335 .394
.118
.118 .217
.217 .315
.315 .394
.118
.118 .276
.197
.197 .276
.276 .335
.335 .394
.118
.118 .217
.217 .315
.315 .394
.118
.118 .276
.197
.197 .276
.276 .335
.335 .394
.118
.118 .217
.217 .315
.315 .394
.118
.118 .276
.197
.197 .276
.276 .335
.335 .394
.118
.118 .217
.217 .315
.315 .394
.118
.118 .276
.197
.197 .276
.276 .335
.335 .394
.118
.118 .217
.217 .315
.315 .394
.118
.118 .276
.157
.157 .276
.157
.157 .276
.008
.006
.004
.003
.008
.006
.004
.003
.004
.003
.008
.006
.004
.003
.008
.006
.004
.003
.004
.003
.008
.006
.004
.003
.008
.006
.004
.003
.004
.003
.008
.006
.004
.003
.008
.006
.004
.003
.004
.003
.008
.006
.004
.003
.008
.006
.004
.003
.004
.003
.008
.004
.008
.004
.197
.004
.197
.006
.197
.004
.157
.157 .276
.004
.003
.006
.004
.004
.003
.006
.004
.003
.006
.004
.197
.197 .276
.078
.078 .197
.197
.197 .276
.276 .335
.118
.118 .217
.118
.006
.157
.003
.157
.003
.118
.003
(Note 1) These cutting conditions are a guide to the standard shank type and the arbor type.
Please make adjustments according to the machining conditions.
(Note 2) Vibration is liable to occur in certain cases. Please reduce the depth of cut and / or reduce cutting conditions in the following cases.
When using the long shank type
When using long tool overhang with the standard or arbor type
When the application has poor clamping rigidity or when using a low rigidity machine.
(Note 3) In case of coarse and ne pitch cutters, the coarse pitch type is recommended to prevent vibration.
(Note 4) For heavy interrupted and unstable cutting, the H breaker insert is the rst recommendation.
y CUTTING CONDITIONS FOR SLOT MILLING

Cutting
Speed
vc
(SFM)
Width
of Cut
ae
(inch)
Hardness
Insert
Grade
Mild Steel
< 180HB
VP15TF
VP20RT
M breaker
Carbon Steel
Alloy Steel
180350HB
VP15TF
M breaker
590
(470 700)
460
(395 525)
< 270HB
VP20RT
M breaker
K Gray Cast Iron Tensile Strength

< 350MPa
Strength
Ductile Cast Iron Tensile
< 800MPa
Work Material
M Stainless Steel
N Aluminum Alloy
H Hardened Steel 4055HRC
& .500"
& .625" & 1.000"
& 1.250" & 1.500"
(& 12mm)
(& 16 mm & 25mm)
(& 32 mm & 40mm)
ap
ap
ap
fz
fz
fz
(IPT)
(inch)
(IPT)
(IPT)
(inch)
(inch)
.157
.157 .276
.157
.157 .276
.157
.157 .276
.157
.157 .276
.157
.157 .276
.004
.003
.004
.003
.004
.003
.004
.003
.004
.003
.118
.118 .197
.118
.118 .197
.118
.118 .197
.118
.118 .197
.118
.118 .197
.004
.003
.004
.003
.004
.003
.004
.003
.004
.003
.004
.197
.008
.197
.006
.003
.157
.003
.118
.003
D1
.118
.004
D1
.118
.004
460
(395 525)
D1
.118
.004
MC5020
H breaker
460
(395 525)
D1
.118
.004
MC5020
H breaker
330
(260 390)
D1
.118
.003
TF15
GM breaker
1640
(655 3280)
D1
.197
VP15TF
H breaker
230
(180 270)
D1
.118
y RAMPING/HELICAL CUTTING
a HELICAL CUTTING
Blind holes,
Flat bottom
Through holes
Pitch
(P)
Pitch
(P)
Hole
diameter
(DH)
Hole
diameter
(DH)
Refer to the table below when using .031 inch radius for maximum ramping angle,
pitch and minimum/maximum hole diameter. Use cutting conditions for slotting to calculate speed and feed when ramping / helical cutting.
Ramping
Cutting Edge
Maximum
Minimum
Diameter
Ramping Angle Distance 1)
D1
L
(inch)
(inch)
%
.500
.625
.750
1.000
1.250
1.500
2.000
2.500
3.000
Helical Cutting (Blind Hole, Flat Bottom)

Minimum
Maximum
Maximum
Maximum
Hole Diameter
Pitch
Hole Diameter 2)
Pitch
P max.
DH min.
P max.
DH max.
(inch)
(inch)
(inch)
(inch)
Helical Cutting (Through Hole)

Minimum
Maximum
Hole Diameter
Pitch
DH min.
P max.
(inch)
(inch)
6
16
3.8
1.4
0.92
1.17
.09
.35
.87
1.1
.07
.27
.63
.79
.020
.079
2.5
1.42
.19
1.35
.17
1.03
.079
4.5
1.92
.23
1.85
.19
1.58
.079
7.5
2.42
.17
2.35
.15
2.05
.079
11.3
2.92
.15
2.85
.13
2.56
.079
22.6
3.92
.07
3.85
.07
3.55
.079
1
1
22.6
22.6
4.92
5.92
.07
.07
4.85
5.85
.07
.07
4.56
5.52
.079
.079
(Note 1) L(=.394"/tan%). Cutters' moving distance until depth of cut reaches .394" at a maximum ramping angle.
(Note 2) In case corner radius of .031". Other than that, nd with the below formula.
{(cutting edge diameter D1) - (corner radius) - .008"} x 2
(Note 3) When machining highly ductile materials with ramping angles above, chips could be continuous.
In this case, decrease the ramping angle or feed per tooth.
MILLING
a RAMPING
K037
MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
Finishing
Roughing
APX4000
Fig.5
D4
D1
D1
D4
.591" Max. Depth of Cut

L2
L1
L2
D1
D4
Fig.6
L1
D4
Fig.2

L2
L1
D4

L2
L1
Fig.3
D1
Fig.4
D1
Fig.1
D4
Cast Iron
D1
Light Alloy

L2
L1

L2
L1

APX4000URpppSApp = Ground shank : See gure 1, 2 and 3.
APX4000URpppFApp = Flat shank : See gure 4 and 5.
Max.
Ramping Type
Angle (Fig.)
Dimensions (inch)

A Holders
B Holders
B Holders
Standard
A Holders
Insert
Anti-seize
Wrench
Screw
Lubricant
a
TPS4S
TIP15W
MK1KS
1
.750
.750
4.000
1.250
14
4
APX4000UR121FA12SA
TPS4S TIP15W MK1KS
.750
.750
4.000 1.250
14
1
121SA12SA a 1
TPS4
TIP15W MK1KS
1.000
.750
4.000 1.250
11
3
162SA12SA a 2
TPS4
TIP15W MK1KS
1.000
1.000
4.500 1.250
11
4
162FA16SA a 2
TPS4
TIP15W MK1KS
1.000
1.000
4.500 1.250
11
2
162SA16SA a 2
TPS4
TIP15W MK1KS
1.250
1.250
5.000 1.750
7
5
202FA20SA a 2
.016
TPS4
TIP15W MK1KS
1.250
1.250
5.000 1.750
7
2
202SA20SA a 2
.079
TPS4
TIP15W MK1KS
1.250
1.250
5.000 1.750
7
5
203FA20SA a 3
TPS4
TIP15W MK1KS
1.250
1.250
5.000 1.750
7
2
203SA20SA a 3
TPS43 TIP15W MK1KS
1.500
1.250
5.000 1.750
7
6
243FA20SA a 3
TPS43 TIP15W MK1KS
1.500
1.250
5.000 1.750
7
3
243SA20SA a 3
TPS43 TIP15W MK1KS
1.500
1.250
5.000 1.750
7
6
244FA20SA a 4
TPS43 TIP15W MK1KS
1.500
1.250
5.000 1.750
7
3
244SA20SA a 4
TPS4S TIP15W MK1KS
.750
.750
4.000 1.250
14
4
APX4000UR121FA12SB a 1
TPS4
TIP15W MK1KS
1.000
1.000
4.500 1.250
11
5
162FA16SB a 2
.125
TPS4
TIP15W MK1KS
1.250
1.250
5.000 1.750
7
5
202FA20SB a 2
a
TPS4
TIP15W MK1KS
3
1.250
1.250
5.000
1.750
7
5
203FA20SB
.157
TPS43 TIP15W MK1KS
1.500
1.250
5.000 1.750
7
6
243FA20SB a 3
TPS43 TIP15W MK1KS
1.500
1.250
5.000 1.750
7
6
244FA20SB a 3
TPS4
TIP15W MK1KS
1.000
1.000
8.500 1.250
11
2
APX4000UR162SA16LA a 2
TPS4
TIP15W MK1KS
1.250
1.250
9.000 1.750
7
2
202SA20LA a 2
.016
TPS4
TIP15W MK1KS
1.250
1.250
9.000 1.750
7
2
203SA20LA a 3
a
TPS43 TIP15W MK1KS
3
1.500
1.500
9.000
1.750
7
2
243SA24LA
.079
TPS43 TIP15W MK1KS
1.500
1.500
9.000 1.750
7
2
244SA24LA a 4
TPS43 TIP15W MK1KS
1.500
1.500 14.000 1.750
7
2
243SA24ELA a 3
TPS4
TIP15W MK1KS
1.000
1.000
8.500 1.250
11
2
APX4000UR162SA16LB a 2
TPS4
TIP15W MK1KS
1.250
1.250
9.000 1.750
7
2
202SA20LB a 2
.125
TPS4
TIP15W MK1KS
1.250
1.250
9.000 1.750
7
2
203SA20LB a 3
a
TPS43
TIP15W
MK1KS
3
1.500
1.500
9.000
1.750
7
2
243SA24LB
.157
TPS43 TIP15W MK1KS
1.500
1.500
9.000 1.750
7
2
244SA24LB a 4
TPS43 TIP15W MK1KS
1.500
1.500 14.000 1.750
7
2
243SA24ELB a 3
(Note) When using inserts with corner radius Re >.125"(3.2mm), B-Holders or C-Holders are required as shown on page K043.
Clamp Torque (lbf-in) : TPS4=31, TPS4S=31, TPS43=31
Long
MILLING
K038
Number of
Teeth
Order Number
Re
(inch)
Stock
Type
Insert Corner
y SHANK TYPE
D1
D4
L1
L2
D12
L8
D9
L1
L7
Max. Depth of Cut

.591"
W1
D8
D11
D1
Order Number
T :+21 +28
I :+15 +22
Dimensions (inch)
D1
L1
D9
L7
D8
D12
W1
L8
APX4000UR0204A
4 2.000 1.625
.750
.748 .415 1.875 .313 .187
0205A
5 2.000 1.625
.750
2505CA
0306DA
0307DA
0408EA
D11
Insert
Anti-seize Coolant thru
% Screw Wrench Lubricant Set Bolt
.600 4
TPS43 TIP15W MK1KS HSCU37513H
.748 .415 1.875 .313 .187
.600 4
5 2.500 2.000 1.000 1.024 .539 2.375 .375 .219
.787 2
6 3.000 2.500 1.250 1.260 .669 2.874 .500 .281 1.024 2
7 3.000 2.500 1.250 1.260 .669 2.874 .500 .281 1.024 2
8 4.000 2.500 1.500 1.181 .787 3.799 .625 .375 1.181 1.5 TPS43 TIP15W MK1KS HSCU75016H
APX4000UR0204B
4 2.000 1.625
.750
.748 .415 1.875 .313 .187
.600 4
0205B
5 2.000 1.625
.750
.748 .415 1.875 .313 .187
.600 4
2505CB
5 2.500 2.000 1.000 1.024 .539 2.375 .375 .219
.787 2
0306DB
6 3.000 2.500 1.250 1.260 .669 2.874 .500 .281 1.024 2
0307DB
7 3.000 2.500 1.250 1.260 .669 2.874 .500 .281 1.024 2
0408EB
8 4.000 2.500 1.500 1.181 .787 3.799 .625 .375 1.181 1.5 TPS43 TIP15W MK1KS HSCU75016H
.016
.079
.125
B Holders
A Holders
Re
(inch)
Stock
Number of Teeth
Insert Corner
Type
y ARBOR TYPE
Max. Ramping Angle
C H :0
A.R :+15 +22
R.R :+21 +28
.157
(Note) When using inserts with corner radius Re >.197"(5.0mm), C-Holders are required as shown on page K043.
Clamp Torque (lbf-in) : TPS43=31

A Holder
B Holder
C Holder
Holder
APX4000URooooooA
.016"
.031"
.039"
.047"
APX4000URooooooB APX4000URooooooC
.063"
.079"
.125"
.157"
.197"
MILLING
.250"

(Re)
INSERTS
K043
OPERATION GUIDANCE
K049
SPARE PARTS
M001
TECHNICAL DATA
N001
K039
MILLING
Fig.1
(Max. Depth of Cut)
Fig.2
(Max. Depth of Cut)
METRIC Standard
Number of Teeth
D4
L1
L2
25
25
115
35
11
32
32
125
45
323SA32SA
32
32
125
403SA32SA
40
32
Standard

.016
.079
.016
Extra Long
MILLING
Long
.079
404SA32SA
40
504SA32SA
505SA32SA
634SA32SA
.079
Max.
Ramping Type
Angle (Fig.)
Dimensions (mm)
Insert
Screw
Wrench Anti-seize
Lubricant
TPS4
TIP15W MK1KS
TPS4
TIP15W MK1KS
45
TPS4
TIP15W MK1KS
125
45
TPS43
TIP15W MK1KS
32
125
45
TPS43
TIP15W MK1KS
50
32
125
45
TPS43
TIP15W MK1KS
50
32
125
45
TPS43
TIP15W MK1KS
63
32
125
45
TPS43
TIP15W MK1KS
636SA32SA
63
32
125
45
TPS43
TIP15W MK1KS
APX4000R252SA25LA
25
25
170
35
11
TPS4
TIP15W MK1KS
282SA25LA
28
25
170
35
TPS4
TIP15W MK1KS
322SA32LA
32
32
190
45
TPS4
TIP15W MK1KS
323SA32LA
32
32
190
45
TPS4
TIP15W MK1KS
352SA32LA
35
32
190
45
TPS4
TIP15W MK1KS
353SA32LA
35
32
190
45
TPS4
TIP15W MK1KS
402SA32LA
40
32
190
45
TPS43
TIP15W MK1KS
403SA32LA
40
32
190
45
TPS43
TIP15W MK1KS
404SA32LA
40
32
190
45
TPS43
TIP15W MK1KS
APX4000R252SA25ELA
25
25
220
80
11
TPS4
TIP15W MK1KS
282SA25ELA
28
25
220
35
TPS4
TIP15W MK1KS
322SA32ELA
32
32
260
100
TPS4
TIP15W MK1KS
323SA32ELA
32
32
260
100
TPS4
TIP15W MK1KS
352SA32ELA
35
32
260
45
TPS4
TIP15W MK1KS
353SA32ELA
35
32
260
45
TPS4
TIP15W MK1KS
402SA32ELA
40
32
260
45
TPS43
TIP15W MK1KS
403SA32ELA
40
32
260
45
TPS43
TIP15W MK1KS
404SA32ELA
40
32
260
45
TPS43
TIP15W MK1KS
Re
(inch)
.016
D1
Order Number
Stock
Insert Corner
Type
y STRAIGHT SHANK TYPE (A Holders)
APX4000R252SA25SA
322SA32SA
Clamp Torque (lbf-in) : TPS4=31, TPS43=31
*
K040
Insert
AOMT
1848pp
PEER-p
(Max. Depth of Cut)
Fig.2
(Max. Depth of Cut)
Fig.1
Cutter Diameter
D1
& 50, & 63
METRIC Standard
& 80
& 100
For metric arbors
-050A05RA
Re
(inch)
.016
.079
& 160
Dimensions (mm)
D1
L1
D9
L7
D8
D12
40 40 16 18
34
-063A06RA
-080A07RA
W1
Max.
Ramping Angle
APX4000-040A04RA
Order Number
Stock
R
Number of Teeth
Insert Corner
& 125
T :+21 +28
I :+15 +22
Mass
C H :0
A.R :+15 +22
R.R :+21 +28
Set Bolt
Geometry
HSC08030H
10030H
12035H
16040H
MBA20040H
24045H
Type (Fig.)
& 40
L8 D11 (kg) %
*
Insert
Screw
Wrench Anti-seize
Lubricant
8.4 5.6 14 0.2 6
TPS43
TIP15W
MK1KS
50 40 22 20 11
45 10.4 6.3 17 0.3 4
TPS43
TIP15W
MK1KS
63 40 22 20 11
50 10.4 6.3 17 0.5 3
TPS43
TIP15W
MK1KS
80 50 27 23 13
60 12.4 7
20 1.2 2
TPS43
TIP15W
MK1KS
-100A08RA
8 100 50 32 25 17
70 14.4 8
27 2.1 1.5 1
TPS43
TIP15W
MK1KS
-125A09RA
9 125 63 40 40 56
90 16.4 9
3.3 1
TPS43
TIP15W
MK1KS
-160A10RA
10 160 63 40 40 72 100 16.4 9
4.8 1
TPS43
TIP15W
MK1KS
Insert
AOMT
1848pp
PEER-p
(Note) When using inserts with corner radius Re >.125" (3.2mm), B-Holders or C-Holders are required as shown on page K043.
MILLING
INSERTS
K043
OPERATION GUIDANCE
K049
SPARE PARTS
M001
TECHNICAL DATA
N001
K041
MILLING
(Max. Depth of Cut)
Fig.2
(Max. Depth of Cut)
Fig.1
Cutter Diameter
D1
& 80
METRIC Standard
& 100
Set Bolt
Geometry
z
HSC12035H
16040H
MBA20040H
24045H
For inch arbors

& 125
APX4000R08007CA
R10008DA
R12509EA
.079
R16010FA
.016
s
s
s
7
8
9
10
D1 L1
[inch]
Type (Fig.)
Dimensions (mm)
T :+21 +28
I :+15 +22
Max.
Ramping Angle
Re
(inch)
Stock
Order Number
Number of Teeth
Insert Corner
& 160
Mass
C H :0
A.R :+15 +22
R.R :+21 +28
L7 D8 D12 W1 L8 D11 (kg) %
D9
80 50 25.4 [1.0"] 26 13 70 9.5 6 20

100 63 31.75 [1.25"] 32 17 80 12.7 8 26
125 63 38.1 [1.5"] 40 56 100 15.9 10
160 63 50.8 [2.0"] 40 72 100 19.1 11
1.2 2
1
2.1 1.5 1
3.3 1
4.8 1
2
2
*
Insert
Screw
TPS43
Wrench Anti-seize
Lubricant
TIP15W MK1KS
TPS43
TIP15W
MK1KS
TPS43
TIP15W
MK1KS
TPS43
TIP15W
Insert
AOMT
1848pp
PEER-p
MK1KS
s
(Max. Depth of Cut)

Section A-A
y SCREW-IN TYPE (A Holders)
D1
2
2
25
28
12.5 23.5
12.5 23.5
57
57
35
35
6
6
19
19
M12 0.2
M12 0.2
TPS4
TPS4
TIP15W MK1KS
TIP15W MK1KS
32
17
28.5
63
40
24
M16 0.3
TPS4
TIP15W MK1KS
32
17
28.5
63
40
24
M16 0.3
TPS4
TIP15W MK1KS
35
17
28.5
63
40
24
M16 0.3
TPS4
TIP15W MK1KS
35
17
28.5
63
40
24
M16 0.3
TPS4
TIP15W MK1KS
3
4
40
40
17
17
28.5
28.5
63
63
40
40
6
6
24
24
M16 0.3
M16 0.3
TPS43
TPS43
TIP15W MK1KS
TIP15W MK1KS
APX4000R252M12A35
282M12A35
322M16A40
323M16A40
352M16A40
353M16A40
403M16A40
404M16A40
Dimensions (mm)
D4
D5
Mass
Stock
Order Number

1
Number of Teeth
MILLING
METRIC Standard
L1
L2
L11
H1
M* (kg)
Insert
Screw
Wrench Anti-seize
Lubricant
1 Clamp Torque (lbf-in) : TPS4=31, TPS43=31
2 Clamp Torque of the Head (lbf-ft) : M12=59.2, M16=66.7
*
*
K042

Insert
AOMT
1848pp
PEER-p
INSERTS
Dimensions (inch)
Shape
Order Number
General Use
M breaker
AOMT184804PEER-M
184808PEER-M
184810PEER-M
184812PEER-M
184816PEER-M
184820PEER-M
AOMT184804PEER-H
184808PEER-H
184816PEER-H
184832PEER-H
184840PEER-H
184850PEER-H
184864PEER-H
Strong Cutting
Edge Type
H breaker
MC5020
VP15TF
VP20RT
Coated
L1
L2
S1
F1
Re
a a
.709
.709
.354
.354
.189
.189
.071
.055
.016
.031
.709
.354
.189
.039
.039
.709
.354
.189
.031
.047
a a
.709
.709
.354
.354
.189
.189
.016
.016
.063
.079
a a a
.709
.709
.354
.354
.189
.189
.071
.055
.016
.031
a a a
.709
.354
.189
.016
.063
.709
.354
.189
.016
.125
.709
.354
.189
.157
.709
.709
.354
.354
.189
.189
.016

a a
s
a a a
Geometry
.197
.250

We offer B-Holders that secures .125"and .157" radius, only for popular inch sizes.

on the right table.
Re
R
Re
Re
.125"
.157"
.197"
.250"
.098"
B-Holders
.197"
C-Holders
: Holder end radius

: Insert corner radius
MILLING
Or additional B-Holders and C-Holders are available as non stock, produced to order only.
"Order numbers"; Please replace the last letter "A" of A-Holders to "B" or "C".
In case of screw-in holders, please add "B" or "C" to the end of the order number of A-Holders.
Ex) APX4000R08007CAAPX4000R08007CC
APX4000R252M12A35APX4000R252M12A35C
OPERATION GUIDANCE
K049
SCREW-IN ARBORS
K142
SPARE PARTS
M001
TECHNICAL DATA
N001
K043
MILLING
Work Material
Hardness
Insert
Grade
/Breaker
Mild Steel
Carbon Steel
Alloy Steel
< 180HB
180 350HB
< 270HB
.25D1
720
(570 860)
.5D1
590
(470 700)
.75D1
590
(440 670)
.25D1
560
(440 670)
.5D1
460
(395 525)
.75D1
590
(470 700)
.25D1
560
(440 670)
.5D1
460
(395 525)
.75D1
MC5020
H breaker
820
(655 985)
.25D1
MC5020
H breaker
785
(625 950)
.5D1
MC5020
H breaker
690
(525 850)
.75D1
MC5020
H breaker
655
(490 820)
.25D1
MC5020
H breaker
620
(460 785)
.5D1
MC5020
H breaker
555
(390 720)
.75D1
VP15TF
VP20RT
M breaker
VP15TF
M breaker
VP20RT
M breaker
MILLING
Gray Cast Iron
Ductile Cast Iron
Tensile
Strength
< 350MPa
Tensile
Strength
< 800MPa
Titanium Alloy
< 350HB
VP20RT
H breaker
130
(100 200)
.25D1
VP20RT
H breaker
100
(65 130)
.25D1
295
(230 350)
.25D1
280
(200 330)
230
(180 270)
.5D1
H
Hardened Steel
K044
Width
of Cut
ae
(inch)
755
(600 900)
Stainless Steel
Cutting
Speed
vc
(SFM)
40 55HRC
VP15TF
H breaker
.75D1
Depth of
Cut
ap
(inch)
Feed per Tooth

fz
(IPT)
& .750" &1.000"&1.500" &2.000"&3.000" & 4.000"
(& 20mm) (&25&40mm) (&50&80mm) (& 100mm)
.197
.197 .295
.295 .394
.394 .492
.492 .591
.197
.197 .295
.295 .394
.394 .492
.492 .591
.197
.197 .394
.394 .591
.197
.197 .295
.295 .394
.394 .492
.492 .591
.197
.197 .295
.295 .394
.394 .492
.492 .591
.197
.197 .394
.394 .591
.197
.197 .295
.295 .394
.394 .492
.492 .591
.197
.197 .295
.295 .394
.394 .492
.492 .591
.197
.197 .394
.394 .591
.197
.197 .295
.295 .394
.394 .492
.492 .591
.197
.197 .295
.295 .394
.394 .492
.492 .591
.197
.197 .394
.394 .591
.197
.197 .295
.295 .394
.394 .492
.492 .591
.197
.197 .295
.295 .394
.394 .492
.492 .591
.197
.197 .394
.394 .591
.197
.197 .295
.295 .394
.006
.004
.003

.006
.004
.003

.004

.006
.004
.003

.006
.004
.003

.004

.006
.004
.003

.006
.004
.003

.004

.006
.004
.003

.006
.004
.003

.004

.006
.004
.003

.006
.004
.003

.003

.006
.004
.002
.012
.010
.008
.006
.004
.012
.010
.008
.006
.004
.008
.006
.004
.012
.010
.008
.006
.004
.012
.010
.008
.006
.004
.008
.006
.004
.012
.010
.008
.006
.004
.012
.010
.008
.006
.004
.008
.006
.004
.012
.010
.008
.006
.004
.012
.010
.008
.006
.004
.008
.006
.004
.010
.008
.006
.004
.003
.010
.008
.006
.004
.003
.008
.006
.004
.006
.004
.002
.012
.010
.008
.006
.004
.012
.010
.008
.006
.004
.008
.006
.004
.012
.010
.008
.006
.004
.012
.010
.008
.006
.004
.008
.006
.004
.010
.008
.006
.004
.003
.010
.008
.006
.004
.003
.006
.004
.003
.012
.010
.008
.006
.004
.012
.010
.008
.006
.004
.008
.006
.004
.010
.008
.006
.004
.003
.010
.008
.006
.004
.003
.008
.006
.004
.004
.002
.010
.008
.006
.004
.003
.010
.008
.006
.004
.003
.006
.004
.003
.010
.008
.006
.004
.003
.010
.008
.006
.004
.003
.006
.004
.003
.010
.008
.006
.004
.003
.010
.008
.006
.004
.003
.006
.004
.003
.010
.008
.006
.004
.003
.010
.008
.006
.004
.003
.006
.004
.003
.010
.008
.006
.004
.003
.010
.008
.006
.004
.003
.006
.004
.003
.004
.002
.079
.004
.004
.002
.002
.197
.197 .295
.295 .394
.197
.197 .295
.004
.003

.004
.003
.006
.004
.003
.004
.003
.006
.004
.003
.004
.003
.006
.004
.003
.004
.003
.197
.003
.003
.003
.003
Hardness
Insert
Grade
/Breaker
Cutting
Speed
vc
(SFM)
Width
of Cut
ae
(inch)
Mild Steel
< 180HB
VP15TF
VP20RT
M breaker
590
(470 700)
D1
Carbon Steel
Alloy Steel
180 350HB
VP15TF
M breaker
460
(395 525)
D1
Stainless Steel
< 270HB
VP20RT
M breaker
460
(395 525)
D1
Gray Cast Iron
Tensile Strength
< 350MPa
MC5020
H breaker
690
(525 850)
D1
Ductile Cast Iron
Tensile Strength
< 800MPa
MC5020
H breaker
555
(390 720)
D1
Titanium Alloy
350HB
VP20RT
H breaker
VP20RT
H breaker
40 55HRC
VP15TF
H breaker
130
(100 200)
100
(65 130)
230
(180 270)
Work Material
M
K
H Hardened Steel
Feed per Tooth

fz
(IPT)
& .750" &1.000"&1.500" &2.000"&3.000" & 4.000"
(& 20mm) (&25&40mm) (&50&80mm) (& 100mm)
Depth of
Cut
ap
(inch)
.197
.197 .295
.295 .394
.197
.197 .295
.295 .394
.197
.197 .295
.295 .394
.197
.197 .295
.295 .394
.197
.197 .295
.295 .394
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
.006
.004
.003
D1
.197
.002
.002
.002
.002
D1
.040
.002
.002
.002
.002
D1
.197
.003
.003
.003
.003
a HELICAL CUTTING
Blind holes,
Flat bottom
Through holes
Pitch
Pitch
Hole
diameter
(DH)
Hole
diameter
(DH)
Refer to the table below when using .031 inch radius for maximum ramping angle,
pitch and minimum/maximum hole diameter. Use cutting conditions for slotting to calculate speed and feed when ramping / helical cutting.
Ramping
Cutting Edge
Maximum
Minimum
Diameter
Ramping Angle Distance 1)
D1
L
(inch)
(inch)
%
.750
1.000
1.250
1.500
2.000
2.500
3.000
4.000
Helical Cutting (Blind Hole, Flat Bottom)

Maximum
Maximum
Minimum
Maximum
Hole Diameter 2)
Pitch
Hole Diameter
Pitch
DH max.
P max.
DH min.
P max.
(inch)
(inch)
(inch)
(inch)
Helical Cutting (Through Hole)

Minimum
Maximum
Hole Diameter
Pitch
DH min.
P max.
(inch)
(inch)
14
2.7
1.42
.51
1.31
.43
.80
.019
11
3.4
1.92
.55
1.81
.47
1.30
.157
5.4
2.42
.43
2.31
.39
1.80
.196
5.4
2.92
.51
2.81
.47
2.30
.275
9.4
3.92
.39
3.81
.39
3.30
.275
18.8
4.92
.23
4.81
.23
4.30
.157
18.8
5.92
.31
5.81
.27
5.30
.236
1.5
25.1
7.92
.31
7.81
.27
7.30
.236
MILLING
a RAMPING
(Note 1) L(=.591"/tan%). Cutters' moving distance until depth of cut reaches .591" at a maximum ramping angle.
(Note 2) In case corner radius of .031". Other than that, nd with the below formula.
{(cutting edge diameter D1) - (corner radius) - .008"} x 2
(Note 3) When machining highly ductile materials with ramping angles above, chips could be continuous.
In this case, decrease the ramping angle or feed per tooth.
K045
MILLING
DEEP SHOULDER
MILLING
Roughing
APX4000
Cast Iron
LONG CUTTING EDGE
Stainless Steel Hardened Steel
D4
D1
Light Alloy
Carbon Steel
Alloy Steel
ap (Max. Depth of Cut)

L2
L1
*1 Combination Type
2412WA24S35A
3212WA32S35A
Order Number
*2
Dimensions (inch)
Total
APX4KUR2408WA24S35A
Stock
R
Number of Flutes
y LONG EDGE SHANK TYPE (A Holders)
Insert Screw
Wrench
Anti-seizure
Lubricant
8 1.500 1.500 6.500 3.250 2.200
TPS43
TIP15W
MK1KS
12 1.500 1.500 6.500 3.250 2.200
TPS43
TIP15W
MK1KS
12 2.000 2.000 6.500 3.250 2.200
TPS43
TIP15W
MK1KS
D4
D1
L1
L2
ap
Insert
AOMT1848
ppPEER-p
*
TIP15W MK1KS
3218WA32M53A a 3 18 2.000 2.000 7.750 4.500 3.300 TPS43
*1
Torque (lbf-in) : TPS43=31
*2 Clamp
(Note
1) When using inserts with corner radius Re > .125" on the bottom, B-Holders or C-Holders are required as shown on page K043.
1
(Note 2) Only corner radius Re .016" and .031" can be used for the peripheral cutting edges expect the bottom cutting edge (the end
cuttting edge).
(Note 3) When using the tool at high spindle speeds, ensure that the tool and arbor are correctly balanced.
L7
W1
D9
D1
D8
L8
ap((Max. Depth of Cut)

L1
MILLING
APX4KUR0209A16A
2516CA22A
Set Bolt
& 2.000"
HSCUF37520
& 2.500"
50028
Geometry
Dimensions (mm)
Total
Stock
Order Number
Number of Flutes
y LONG EDGE SHELL TYPE (A Holders)
D1
Insert Screw
Wrench
Anti-seizure
Lubricant
9 2.000 2.500 .750 1.063 .415 1.918 .313 .187 1.650
TPS43
TIP15W
MK1KS
AOMT1848
4 16 2.500 3.500 1.000 1.339 .539 2.409 .375 .219 2.200
TPS43
TIP15W
MK1KS
ppPEER-p
D1
L1
D9
L7
D8
D7
W1
L8
ap
Insert

*(Note
1) When using inserts with corner radius Re > .125" on the bottom, B-Holders or C-Holders are required as shown on page K043.
(Note 2) Only corner radius Re .016" and .031" can be used for the peripheral cutting edges expect the bottom cutting edge (the end cuttting edge).
(Note 4) In case of internal coolant supply, please use a face mill arbor with through coolant channels. Regular center-thru or side-thru arbors can't be used.
K046
D4
D1
L2
L1
*1 Combination Type
METRIC Standard
APX4KR4008SA42S056A
4012SA42S056A
1
5012WA508S056A
5018WA508M084A
1
s
s
s
Total
Order Number
Number of Flutes
Stock
y LONG EDGE SHANK TYPE (A Holders)
2
3
8
12
Dimensions (mm)
40
40
42
42
160
160
80
80
56
56
TPS43
TIP15W
Anti-seizure
Lubricant
MK1KS
TPS43
TIP15W
MK1KS
50
50
50.8 [2.0"]
50.8 [2.0"]
160
190
80
110
56
84
TPS43
TIP15W
MK1KS
D1
3
3
12
18
*2
[inch]
D4
L1
L2
ap
Insert Screw
Wrench
Insert
AOMT1848
ppPEER-p
*
s
TPS43
TIP15W MK1KS
*
2 Clamp Torque (lbf-in) : TPS43=31
* 1) When using inserts with corner radius Re > .125" on the bottom, B-Holders or C-Holders are required as shown on page K043.
(Note
L7
W1
D9
D1
D8
L8

L1
For metric arbors
Order Number
APX4K-050A09A042RA
-063A16A056RA
s
s
Geometry
& 50mm
HSC10050
& 63mm
12070
The bore diameter (D9) is equivalent to a metric size.
Dimensions (mm)
Total
Stock
Number of Flutes
Set Bolt
D1 L1
D9
L7 D8
D7
W1
L8
3 9 50 65
4 16 63 85
22
27
22 11 48
10.4 6.3 42
28 13 60.7 12.4 7
56
TPS43
TIP15W
Anti-seizure
Lubricant
MK1KS
TPS43
TIP15W
MK1KS
ap Insert Screw
Wrench
Insert
AOMT1848
ppPEER-p
* Clamp Torque (lbf-in) : TPS43=31

METRIC Standard
For inch arbors
MILLING
METRIC Standard
D1
APX4KR06316CA056A
R
s
4 16 63 85 25.4 [1.0"] 26 13 60.7
Dimensions (mm)
Total
Stock
Order Number
Number of Flutes
D1 L1
D9
L7 D8
[inch]
D7
W1
L8
ap Insert Screw
Wrench
Anti-seizure
Lubricant
9.5
56
TIP15W
MK1KS
TPS43
Insert
AOMT1848
ppPEER-p

(Note 1) When using inserts with corner radius Re > .125" on the bottom, B-Holders or C-Holders are required as shown on page K043.
(Note 4) In case of internal coolant supply, please use a face mill arbor with through coolant channels. Regular center-thru or side-thru arbors can't be used.
INSERTS
K043
OPERATION GUIDANCE
K049
SPARE PARTS
M001
TECHNICAL DATA
N001
K047
MILLING
RECOMMENDED CUTTING CONDITIONS (Long Cutting edge Shank and Shell Type)
Work Material
Hardness
Insert
Grade/Breaker
(SFM)
(inch)
655
(525 820)
0.15D1
525
(395 655)
0.3D1
525
(395 655)
0.15D1
395
(330 460)
0.3D1
525
(395 655)
0.15D1
395
(330 460)
0.3D1
MC5020
H breaker
755
(590 920)
0.15D1
MC5020
H breaker
620
(460 790)
0.3D1
MC5020
H breaker
620
(460 720)
0.15D1
MC5020
H breaker
560
(390 720)
0.3D1
40
(30 60)
30
(20 40)
0.15D1
P
Mild Steel
Carbon Steel
Alloy Steel
< 180HB
180 350HB
VP15TF
M breaker
VP15TF
M breaker
M
Stainless Steel
< 270HB
K
Cast Iron
Ductile Cast Iron
Tensile
Strength
< 350MPa
Tensile
Strength
< 800MPa
Cutting Speed Width of Cut Depth of Cut

vc
ae
ap
VP20RT
M breaker
Titanium Alloy
< 350HB
VP20RT
H breaker
VP20RT
H breaker
0.15D1
(inch)
Feed per Tooth

fz (IPT)
&2.0"(Max.ap=2.2")
&1.5"(Max.ap=2.2")
&2.0"(Max.ap=3.3")
&2.5"(Max.ap=2.2")
&2.0"(Max.ap=1.65")
&40(Max.ap=56mm(2.205") &50(Max.ap=56mm(2.205") &50(Max.ap=84mm(3.307")
&50 (Max.ap=42mm(1.654") &63 (Max.ap=56mm(2.205")
.787
1.969
3.150
.787
1.969
3.150
.787
1.969
3.150
.787
1.969
3.150
.394
1.969
3.150
.394
1.969
3.150
.394
1.969
3.150
.394
1.969
3.150
.394
1.969
3.150
.394
1.969
3.150
.787
1.969
.010
.008

.010
.008

.010
.008

.010
.008

.010
.008

.010
.008

.012
.010

.010
.008

.010
.008

.008
.006

.004
.004
.010
.008

.010
.008

.010
.008

.010
.008

.010
.008

.010
.008

.012
.010

.010
.008

.010
.008

.008
.006

.004
.004
.008
.006
.004
.008
.006
.004
.008
.006
.004
.008
.006
.004
.008
.006
.004
.008
.006
.004
.010
.008
.006
.010
.006
.004
.008
.006
.004
.006
.004
.003

.394
.003
.003
(Note 1) The above cutting conditons are determined based on high rigidity machine and workpiece, where no vibration occurred.
Please adjust processing conditions if the vibration is generated.
MILLING
Work Material
M
K
Insert
Grade/Breaker
Cutting Speed Width of Cut Depth of Cut

vc
ae
ap
(SFM)
Mild Steel
< 180HB
VP15TF
M breaker
Carbon Steel
Alloy Steel
180 350HB
VP15TF
M breaker
460
(395460)
330
(260 395)
Stainless Steel
< 270HB
VP20RT
M breaker
330
(260 395)
Tensile
Strength
< 350MPa
Tensile
Strength
< 800MPa
MC5020
H breaker
MC5020
H breaker
620
(460 790)
560
(390 720)
VP20RT
130
(100 200)
100
(65 130)
Cast Iron
Ductile Cast Iron
Hardness
Titanium Alloy
< 350HB
H breaker
VP20RT
H breaker
(inch)
(inch)
Feed per Tooth

fz (IPT)
&2.0"(Max.ap=2.2")
&1.5"(Max.ap=2.2")
&2.0"(Max.ap=3.3")
&2.5"(Max.ap=2.2")
&2.0"(Max.ap=1.65")
&40(Max.ap=56mm(2.205") &50(Max.ap=56mm(2.205") &50(Max.ap=84mm(3.307")
&50 (Max.ap=42mm(1.654") &63 (Max.ap=56mm(2.205")
.787
1.969
.787
1.969
.008
.006
.006
.004
.008
.006
.006
.004
.006

.004
.394
.004
.004
.003
.394
.1969
.394
.1969
.010
.008
.006
.004
.010
.008
.006
.004
.008
.006
.004
D1
.1969
.003
.003
D1
.787
.002
.002
D1
D1
D1
D1
D1
K048
a Use only specied inserts and parts.
a Clamp the inserts at a specied torque of only.
aThe maximum allowable spindle speeds are shown in Table 1. Ensure that the cutter operates under the
maximum allowable spindle speed.
The maximum allowable spindle speeds for safety purposes are determined in accordance with ISO15641
(Milling Cutters for high speed machiningSafety requirements).
(Table 1) Maximum allowable spindle speed
Cutting Edge Diameter (inch)
& .500"
& .625"
& .750"
Max. Allowable Spindle Speed (min-1)
& 1.000" & 1.250" & 1.500" & 2.000" & 2.500" & 3.000" & 4.000"
9900
19000
16000
Cutting Edge Diameter D1(mm)
12
14
16
18
20
22
25
28
30
19000
17000
15000
14000
12000
11000
10000
32
35
40
50
63
80
100
125
160
9500
9000
7500
6000
5000
3500
3000
2500
1500
9500
7600
6000
4800
3800
3100
MILLING
12000
K049
MILLING
MULTI FUNCTIONAL
MILLING
Roughing
BAP3500
Light Alloy
Cast Iron
Fig.2
Fig.1
(Max. Depth of Cut)
Fig.3

a High rake insert.
a Copy milling is possible.
Stock
Corner
Radius
Order Number
LB
SB
SA
.016
.031
.094
.118
.125
.094
.118
.125
BAP3500R122WA12SA
163WA16SA
204WA20SA
BAP3500R122WA12SB
163WA12SB
163WA16SB
204WA20SB
BAP3500R122SA12LB
163SA16LB
204SA20LB
a
a
a
a
a
a
a
a
a
a
Number of Teeth
Type
y SHANK TYPE
D1
L1
D4
L2
2
3
4
2
3
3
4
2
3
4
.750
1.000
1.250
.750
1.000
1.000
1.250
.750
1.000
1.250
4.375
4.750
5.125
4.375
4.750
4.750
5.125
7.250
8.500
9.000
.750
1.000
1.250
.750
.750
1.000
1.250
.750
1.000
1.250
1.38
1.57
1.97
1.38
1.57
1.57
1.97
1.38
1.57
1.97
Dimensions (inch)
Max.
Depth Type
of Cut (Fig.)
ap
Insert Screw
2 TS32
.433
3 TS32
.433
3 TS32
.433
2 TS32
.433
2 TS32
.433
3 TS32
.433
3 TS32
.433
1 TS32
.433
1 TS32
.433
1 TS32
.433
Wrench
TKY08F
TKY08F
TKY08F
TKY08F
TKY08F
TKY08F
TKY08F
TKY08F
TKY08F
TKY08F
Insert
XPMT13T3PDER-M1/M2
XPGT13T3PDFR-G1/G2
XPMT13T3PDER-M6/M75/M8
XPGT13T3PDFR-G6/G75/G8
XPMT13T3PDER-M6/M75/M8
XPGT13T3PDFR-G6/G75/G8
(Note) Please use insert corner R.016 or R.031 for SA type holders, and insert corner R.094, R.118 or R.125 for SB and LB type holders.
MILLING
D1
C H :0
A.R :+12 +14
R.R :+0 +4
.016
.031
BAP3500R1504A
0204A
0206A
2504A
2506A
0306A
0308A
Stock
Order Number
*
K050
a
a
a
a
a
a
a
Number of Teeth
y ARBOR TYPE
Corner
Radius
D1
4
4
6
4
6
6
8
1.500
2.000
2.000
2.500
2.500
3.000
3.000

1.5
2
2.5
3
Dimensions (inch)
L1
Coolant thru Set Bolt

HSCU25014H
37513H
37513H
50014H
D9
L7
1.575
.500
.630
1.575
.750
.748
1.575
.750
.748
1.575
.750
.748
1.575
.750
.748
1.969 1.000 1.024
1.969 1.000 1.024
D8
W1
L8
.276
.415
.415
.415
.415
.512
.512
.250
.313
.313
.313
.313
.375
.375
.156
.187
.187
.187
.187
.219
.219
Max.
Depth
of Cut
ap Insert Screw
.433 TS32
.433 TS32
.433 TS32
.433 TS32
.433 TS32
.433 TS32
.433 TS32
Insert
Wrench
TKY08F
TKY08F
TKY08F XPMT13T3PDER-M1/M2
TKY08F XPGT13T3PDER-G1/G2
TKY08F XPGT13T3PDFR-G1/G2
TKY08F
TKY08F
INSERTS
P
M
K
N
S
H
Work
Material
Steel
: Stable Cutting
Stainless Steel
Cast Iron
Honing :
E : Round F : Sharp

Hardened Materials
Dimensions (inch)
Order Number
M breaker
XPMT13T3PDER-M1
13T3PDER-M2
13T3PDER-M6
13T3PDER-M75
13T3PDER-M8
XPGT13T3PDER-G1
13T3PDER-G2
13T3PDER-G6
13T3PDER-G75
13T3PDER-G8
XPGT13T3PDFR-G1
13T3PDFR-G2
13T3PDFR-G6
13T3PDFR-G75
13T3PDFR-G8
M
M
M
M
M
G
G
G
G
G
G
G
G
G
G
E
E
E
E
E
E
E
E
E
E
F
F
F
F
F
HTi10
Class
Honing
F7030
VP15TF
Shape
G breaker
: Unstable Cutting
Non-Ferrous Metal
Coated Carbide
G breaker
: General Cutting
a a
a a
a a
a a
a a
a
a
a
a
a
a
a
a
a
a
L1
L2
S1
F1
Re
.512
.512
.512
.512
.512
.512
.512
.512
.512
.512
.512
.512
.512
.512
.512
.311
.311
.311
.311
.311
.311
.311
.311
.311
.311
.311
.311
.311
.311
.311
.156
.156
.156
.156
.156
.156
.156
.156
.156
.156
.156
.156
.156
.156
.156
.063
.047
.016
.016
.016
.063
.047
.016
.016
.016
.063
.047
.016
.016
.016
.016
.031
.094
.118
.125
.016
.031
.094
.118
.125
.016
.031
.094
.118
.125
Geometry

SA Holder
SB, LB Holder
BAP3500RooooooooA
BAP3500RooooooooB
Holder

(Re)
XPoT........-M1/G1
XPoT........-M2/G2
XPoT........-M6/G6
XPoT........-M75/G75
XPoT........-M8/G8
(Note) Other combinations of holder and insert corner R are not acceptable.

P
Mild Steel
Hardness
Grade
Breaker
< 180HB
VP15TF
General Cutting
800 1200
.006 (.004 .008)
VP15TF
General Cutting
700 1000
.006 (.004 .008)
Unstable Cutting
600 700
.006 (.004 .008)
General Cutting
600 700
.006 (.004 .008)
General Cutting
300 700
.006 (.004 .008)
Unstable Cutting
300 500
.008 (.004 .010)
General Cutting
700 1000
.006 (.004 .008)
General Cutting
600 800
.006 (.004 .008)
General Cutting
500 700
.004 (.002 .006)
Carbon Steel 180280HB F7030

Alloy Steel
280350HB VP15TF
F7030
Stainless Steel < 200HB
VP15TF
F7030
Tensile Strength
K Gray Cast Iron < 350MPa VP15TF
F7030
Tensile Strength VP15TF
< 450MPa
Ductile Cast Iron Tensile Strength

500 800 VP15TF
MPa

(SFM)
(inch/tooth)
Ramping Angle %
.008 (.004 .012)
.750
9.0
65 150
.006 (.004 .008)
1.000
5.5
100 300
.004 (.002 .006)
1.250
4.0
HTi10
General Cutting
1000 3000
.008 (.004 .012)
S Titanium Alloy
> 350HB
VP15TF
General Cutting
100 250
VP15TF
General Cutting
> 40HRC
VP15TF
General Cutting
H Hardened Steel
(Max.)
Diameter of Cutting Edge (inch)
N Aluminum Alloy
MILLING
Work Material
y MAX. RAMPING ANGLE (%)
Cutting
Mode
The gure above are the guidelines for conditions of general cutting by a standard type tool.
SPARE PARTS
M001
TECHNICAL DATA
N001
K051
MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
<CUTTING FOR ALUMINUM ALLOY>
Finishing
Roughing
AXD4000
Carbon Steel Alloy Steel Stainless Steel Hardened Steel
D12
D9
W1
125
D8
D11
D1
L7
L1
ap
ap
ap
L1
L1
50
63
80
100
D12
D9
W1
Fig. 3
L8
Fig. 2
L7
40
D12
D9
W1
L8
Fig. 1
L7
Cast Iron
L8
Light Alloy
D8
D1
D8
D11
D1
Cutter Diameter
D1
METRIC Standard
& 40
For inch arbors
& 50, & 63

& 80
A Holders
& 125
40 50 16
-040A03RA
40 50 16
18 8.5 34 8.4 5.6 12 0.3 15.5 41000 1 TS3SB TKY08D MK1KS
-050A02RA
50 50 22
20 11
45 10.4 6.3 17 0.4 15.5 35000 2 TS3SB TKY08D MK1KS
-050A04RA
50 50 22
20 11
45 10.4 6.3 17 0.4 15.5 35000 2 TS3SB TKY08D MK1KS
-063A05RA
63 50 22
20 11
50 10.4 6.3 17 0.6 15.5 30000 2 TS3SB TKY08D MK1KS
R08005CA
R10006DA
R12507EA
L7 D8 D12 W1
25.4
5 80 50
26 13
[1.0"]
31.75
6 100 63
32 17
[1.25"]
38.1
7 125 63
40 56
[1.5"]
Max.
Spindle
Speed
ap (min-1)
L8 D11 (kg) (mm)
Type (Fig.)
Mass
D9
[inch]
Max.
Depth of Cut
AXD4000-040A02RA
Clamp Wrench Anti-seize

Lubricant
Screw
18 8.5 34 8.4 5.6 12 0.3 15.5 41000 1 TS3SB TKY08D MK1KS
Stock
D1 L1
Dimensions (mm)
60 9.5 6
20 1.0 15.5 27000 2 TS3SB TKY08D MK1KS
70 12.7 8
26 2.0 15.5 23000 2 TS3SB TKY08D MK1KS
90 15.9 10
2.8 15.5 20000 3 TS3SB TKY08D MK1KS
AXD4000-040A02RB
40 50 16
18 8.5 34 8.4 5.6 12 0.3 14.8 41000 1 TS3SB TKY08D MK1KS
-040A03RB
40 50 16
18 8.5 34 8.4 5.6 12 0.3 14.8 41000 1 TS3SB TKY08D MK1KS
-050A02RB
50 50 22
20 11
45 10.4 6.3 17 0.4 14.8 35000 2 TS3SB TKY08D MK1KS
-050A04RB
50 50 22
20 11
45 10.4 6.3 17 0.4 14.8 35000 2 TS3SB TKY08D MK1KS
-063A05RB
63 50 22
20 11
50 10.4 6.3 17 0.6 14.8 30000 2 TS3SB TKY08D MK1KS
5.0
R08005CB
80 50
R10006DB
6 100 63
R12507EB
4.0
25.4
26 13
[1.0"]
31.75
32 17
[1.25"]
38.1
7 125 63
40 56
[1.5"]
60 9.5 6
20 1.0 14.8 27000 2 TS3SB TKY08D MK1KS
70 12.7 8
26 2.0 14.8 23000 2 TS3SB TKY08D MK1KS
90 15.9 10
2.8 14.8 20000 3 TS3SB TKY08D MK1KS
(Note 1) The maximum spindle speeds are set to ensure tool and insert stability.
Before operating the tool read the operation guidance on page K054.
(Note 3) Note for insert with a corner radius of .063" and above, as corner radius increases the L1 dimension decreases.
Clamp Torque (lbf-in) : TS3SB=13
K052
B Holders
MILLING
3.2
T :+21 +26
I :+14 +15
Order Number
Re
0.4
& 100
HFF08043H
HSC10030H
12035H
16040H
MBA20040H
Geometry
z
Number of Teeth
Type
Insert Corner
y ARBOR TYPE
C H :0
A.R :+14 15
R.R :+21 +26
Set Bolt
Insert
XDGX1750pp
PDFR-GL
D1
D1
D4
Fig. 2
D4
Fig. 1
ap
ap
L2
L2
L1
L1
METRIC Standard
4.0
5.0
Stock
R
AXD4000R252SA25SA
252SA25LA
322SA32SA
322SA32LA
403SA32SA
403SA42SA
AXD4000R252SA25SB
252SA25LB
322SA32SB
322SA32LB
403SA32SB
403SA42SB
s
s
s
s
s
s
s
s
s
s
s
s
Max.
Spindle
Speed
ap
(min-1)
Type (Fig.)
3.2
Order Number
Max.
Depth of Cut
0.4
49000
49000
48000
48000
41000
41000
49000
49000
48000
48000
41000
41000
1
1
1
1
2
1
1
1
1
1
2
1
Number of Teeth
Insert
Corner
Re
B Holders
A Holders
Type
y SHANK TYPE
D1
L1
L2
D4
(mm)
2
2
2
2
3
3
2
2
2
2
3
3
25
25
32
32
40
40
25
25
32
32
40
40
125
170
150
200
150
170
125
170
150
200
150
170
50
80
50
80
50
80
50
80
50
80
50
80
25
25
32
32
32
42
25
25
32
32
32
42
15.5
15.5
15.5
15.5
15.5
15.5
14.8
14.8
14.8
14.8
14.8
14.8
Dimensions (mm)
Clamp
Screw
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
Wrench
TKY08D
TKY08D
TKY08D
TKY08D
TKY08D
TKY08D
TKY08D
TKY08D
TKY08D
TKY08D
TKY08D
TKY08D
Anti-seize
Lubricant
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
Insert
XDGX1750pp
PDFR-GL
(Note 3) Note for insert with a corner radius of .063" and above, as corner radius increases the L1 and L2 dimension decreases.
Clamp Torque (lbf-in) : TS3SB=13
INSERTS
Cutting Conditions (Guide):
:Stable Cutting
:General Cutting
Aluminum Alloy
Order Number
XDGX175004PDFR-GL
175008PDFR-GL
175012PDFR-GL
175016PDFR-GL
175020PDFR-GL
175024PDFR-GL
175030PDFR-GL
175032PDFR-GL
175040PDFR-GL
175050PDFR-GL
G
G
G
G
G
G
G
G
G
G
F
F
F
F
F
F
F
F
F
F
Honing:
F :Sharp
Dimensions (mm)
L1
L4
S1
F1
Re
23.0
23.0
23.0
22.0
22.0
22.0
21.1
21.1
20.0
19.4
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
5
5
5
5
5
5
5
5
5
5
1.7
1.3
0.9
1.4
1.0
0.6
0.8
0.6
0.8
0.4
0.4
0.8
1.2
1.6
2.0
2.4
3.0
3.2
4.0
5.0
Geometry
TF15
Shape
Class
Honing
LC15TF
Stock
Coated Carbide
:Unstable Cutting
L1
Re
20
S1
30
L4
MILLING
F1
Work Material
y HOLDER AND INSERT CORNER RADIUS COMBINATION

Holder
.016"
Insert
Corner
Radius
(Re)
.031"
.047"
A Holder
B Holder
AXD4000pppppppA
AXD4000RppppppppA
AXD4000pppppppB
AXD4000RppppppppB
.063"
.079"
.094"
.118"
.126"
.157"
.197"
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
175004PDFR-GL 175008PDFR-GL 175012PDFR-GL 175016PDFR-GL 175020PDFR-GL 175024PDFR-GL 175030PDFR-GL 175032PDFR-GL 175040PDFR-GL 175050PDFR-GL
SPARE PARTS
M001
TECHNICAL DATA
N001
K053
MILLING
y SHOULDER MILLING
Work Material
Insert
Grade
Width of Cut Cutting Speed

ae
vc
(inch)
(SFM)
0.25 D1
3280
(655 9840)
0.5 D1
3280
(655 9840)
0.75 D1
3280
(655 9840)
Aluminum Alloy
LC15TF
TF15
Depth of Cut
ap
(inch)

Cutting Edge DiameterD1 Cutting Edge DiameterD1 Cutting Edge DiameterD1 Cutting Edge DiameterD1
&25
& 32
& 40
& 50 & 125
.197
.197 .295
.295 .393
.393 .492
.492 .571
.197
.197 .295
.295 .393
.393 .492
.492 .571
.197
.197 .295
.295 .393
.393 .492
.492 .571
.014
.013
.012
.011
.010
.014
.013
.012
.010
.008
.012
.011
.010
.009
.008
.014
.013
.012
.011
.010
.014
.013
.012
.011
.010
.012
.011
.010
.009
.008
.016
.015
.014
.013
.012
.014
.013
.012
.011
.010
.012
.011
.010
.009
.008
.016
.015
.014
.013
.012
.016
.015
.014
.013
.012
.014
.013
.012
.011
.010
y SLOT MILLING
Work Material
Insert
Grade
Width of Cut Cutting Speed

ae
vc
(inch)
(SFM)
(inch)
3280
(655 9840)
.197
.197 .295
.295 .393
.393 .492
.492 .571
N
Aluminum Alloy
LC15TF
TF15
D1
Depth of Cut
ap

Cutting Edge DiameterD1 Cutting Edge DiameterD1 Cutting Edge DiameterD1 Cutting Edge DiameterD1
& 25
& 32
& 40
& 50 & 125
.010
.009
.008

.010
.009
.008
.007
.006
.012
.011
.010
.009
.008
.014
.013
.012
.011
.010
(Note 1) The above cutting conditions are determined based on high workpiece and machine rigidity, where no vibration occurred. If vibrations
occur make adjustments according to the machining conditions.
(Note 2) Note, vibrations may occur in the following conditions.
When using long tool overhang.
When pocket machining corner radii.
When the workpiece has poor clamping rigidity or when the machine rigidity or workpiece rigidity is low, vibrations can occur easily, if so, reduce
cutting conditions such as width and depth of cut and feed per tooth.
Only use the inserts and parts provided by Mitsubishi Materials with this tool. Use of the correct insert clamp screws is
especially important to ensure overall tool safety. Do not use damaged or worn clamp screws.
Clamp Screw Number
Overall Length L(inch)
Clamp Torque (lbf-in)
25125
TS3SB
.315
13
First
MILLING
aWhen tightening the clamp screws, follow the order in Figure 1.

a The maximum allowable spindle speeds are shown in Table 1. Ensure that the cutter operates under the

Second
Figure 1

25
49000
32
48000
40
41000
50
35000
63
30000
80
27000
100
23000
125
20000
a Even when operating under the maximum allowable spindle speed, if the spindle speed is equal to or higher than the values shown in table 2, it is recommended
that the balance quality (with the arbor or milling chuck) conforms to G6.3 or better based on ISO1940. It is also recommended to replace the clamp screws with
new ones when changing inserts. Furthermore, ensure to use machines that are provided with safety measures in case of cutter breakage.
The balance quality of the holder (without inserts and clamp screws) is G6.3 or better at 10000min-1.
(Table 2) Maximum spindle speed when balancing with the arbor or milling chuck has not been achieved
Max. Spindle Speed (min-1)
25
12000
32
9500
40
7600
50
6000
63
4800
80
3800
100
3000
a When setting the spindle speed, take into consideration the maximum allowable spindle speed of the arbor or milling chuck.
a Use the specied set bolt when using the arbor type with through coolant.
a The inserts have sharp cutting edges and handling them with bare hands may cause injuries. Always wear safety gloves when handling the indexable inserts.
K054
125
2400
a RAMPING
Blind holes,
Flat bottom
a HELICAL CUTTING
L
Pitch
(P)
Pitch
(P)
L=
%
Through holes
ap
tan %
ap
D1
D1
Hole
diameter
(DH)
RAMPING/HELICAL CUTTING
D1
Hole
diameter
(DH)
Cutting
Ramping
Helical Milling (Blind Hole, Flat Bottom)
Helical Milling (Through Hole)
Insert
Edge
Holder Diameter Corner Radius
Minimum Distance Maximum Hole Diameter Maximum Pitch Minimum Hole Diameter Maximum Pitch Minimum Hole Diameter Maximum Pitch
Maximum
Re
Type
1
L
DH max.
P max.
DH min.
P max.
DH min.
P max.
Ramping Angle
D1
(inch)
(inch)
(inch)
(inch)
(inch)
(inch)
(inch)
(inch)
%
(mm)
.01 6 .047
1.142
1.799
1.063
1.22
.276
23.1
1.46
1.913 2
.063 .094
25
22.0
1.54
1.819 3
.945
1.736
.945
1.22
.276
.118 .125
18.7
1.81
1.709 4
.748
1.677
.709
1.26
.236
.016 .047
15.4
2.24
2.465 2
.984
2.350
.945
1.772
.394
32
.063 .094
14.7
2.36
2.370 3
.827
2.283
.827
1.772
.394
.118 .125
.748
2.224
.709
1.772
.354
13.8
2.52
2.260 4
.016 .047
11.1
3.11
3.094 2
.866
2.980
.866
2.402
.472
40
.063 .094
10.4
3.35
3.000 3
.787
2.913
.748
2.402
.433
.118 .125
9.7
3.58
2.890 4
.669
2.850
.669
2.402
.433
.016 .047
8.2
4.25
3.882 2
.827
3.768
.787
3.189
.512
50
.063 .094
7.6
4.61
3.787 3
.709
3.697
.709
3.189
.472
.118 .125
6.9
5.08
3.677 4
.630
3.638
.630
3.189
.433
A
.016 .047
6.1
5.71
4.906 2
.787
4.787
.748
4.213
.551
63
.063 .094
5.6
6.26
4.811 3
.669
4.720
.669
4.213
.512
.118 .125
.630
4.657
.591
4.213
.472
5.2
6.73
4.701 4
.016 .047
4.6
7.60
6.244 2
.748
6.126
.748
5.551
.591
.063 .094
80
4.2
8.35
6.150 3
.669
6.059
.669
5.551
.512
.118 .125
.591
5.996
.591
5.551
.472
3.8
9.21
6.039 4
.016 .047
3.5
10.00
7.819 2
.709
7.701
.709
7.126
.591
100
.063 .094
3.2
10.94
7.724 3
.630
7.634
.630
7.126
.551
.118 .125
.551
7.571
.551
7.126
.472
2.9
12.05
7.614 4
.016 .047
.709
9.669
.669
9.094
.591
2.7
12.95
9.787 2
125
.063 .094
2.5
13.98
9.693 3
.630
9.602
.630
9.094
.551
.118 .125
2.3
15.20
9.583 4
.551
9.539
.551
9.094
.512
.157
15.1
2.17
1.654
.551
1.602
.512
1.260
.197
25
.197
13.7
2.40
1.583
.433
1.567
.433
1.299
.197
.157
12.7
2.60
2.201
.630
2.150
.630
1.772
.315
32
.197
12.0
2.76
2.130
.551
2.110
.551
1.772
.315
.157
8.8
3.78
2.823
.591
2.776
.551
2.402
.394
40
.197
8.2
4.06
2.748
.512
2.736
.512
2.402
.354
.157
6.3
5.31
3.606
.551
3.563
.551
3.189
.394
50
.197
5.8
5.75
3.531
.472
3.520
.472
3.189
.354
B
.157
4.6
7.24
4.630
.512
4.583
.512
4.213
.433
63
.197
4.2
7.95
4.555
.472
4.543
.472
4.213
.394
.157
3.4
9.84
5.969
.512
5.921
.512
5.551
.433
80
.197
3.1
10.79
5.894
.433
5.882
.433
5.551
.394
.157
2.6
12.83
7.543
.512
7.496
.472
7.126
.433
100
.197
2.4
13.94
7.469
.433
7.457
.433
7.126
.394
.157
2.0
16.69
9.512
.472
9.465
.472
9.094
.433
125
.197
1.8
18.54
9.437
.433
9.425
.433
9.094
.394
MILLING
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
(Note) The recommended ramping feed is .002inch/tooth or under.

*1) Using the maximum ramping angle, the distance to reach the maximum depth of cut is as follows:
L= (maximum depth of cut ap/tan %). Maximum depth of cut A type is .610inch, B type is .582inch.
*2) Corner radius of .016inch. For other corner radii, use the following formula. {(cutting edge diameter D1)(corner radius Re) 0.3}2
)
Corner radius of .063inch. For other corner radii, use the following formula. {(cutting edge diameter D1)(corner radius Re) 0.3}2
3
*
*4) Corner radius of .118inch. For other corner radii, use the following formula. {(cutting edge diameter D1)(corner radius Re) 0.3}2
y MAX.DRILLING DEPTH
Holder
Type
Insert
Corner R
Re
(inch)
A
B
.016 .047
.063 .094
.118 .125
.157
.197
Max.Drilling Depth (inch)

Cutting Edge Diameter D1 Cutting Edge Diameter D1 Cutting Edge Diameter D1
& 32mm
& 40 & 125mm
& 25mm
.205
.181
.146
.106
.091
.205
.185
.165
.142
.130
.209
.189
.173
.150
.138
AXD4000 can be effectively used for

pocket machining without the need
for a prepared hole.
K055
MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
<CUTTING FOR ALUMINUM ALLOY>
Finishing
AXD7000
Light Alloy
Cast Iron
Roughing
Fig.2
Fig.1

a Low resistance
inserts.
a Excellent wall
accuracy.
a High spindle
Cutter Diameter
D1
speeds possible.
a Multi functional
milling.
& 2"
& 3"
& 4"
C H :0
A.R :+11
R.R :+26 +27
x
0405EA
0506EA
6 5.000 2.500 1.500 1.575 2.205 3.810 .625 .375 1.181 6.6 .827 3 20000 2 TS4SBL TKY15D MK1KS
3 2.000 2.000 .750 .748 .415 1.875 .313 .187 .600 .9 .803 8 30000 1 TS4SBL TKY15D MK1KS
0303DB
0405EB
3 3.000 2.500 1.250 1.260 .669 2.750 .500 .281 1.024 2.6 .803 4 23000 1 TS4SBL TKY15D MK1KS XDGX2270pp
5 4.000 2.500 1.500 1.181 .787 3.810 .625 .375 1.181 5.4 .803 3 23000 1 TS4SBL TKY15D MK1KS PDFR-GL
0506EB
6 5.000 2.500 1.500 1.575 2.205 3.810 .625 .375 1.181 6.6 .803 2 20000 2 TS4SBL TKY15D MK1KS
AXD7000UR0203B
.157
.197
Max.
Spindle
Speed
D1 L1 D9 L7 D8 D12 W1 L8 D11 (lbs) ap % (min-1)
Type (Fig.)
.125
3 3.000 2.500 1.250 1.260 .669 2.750 .500 .281 1.024 2.6 .827 5 23000 1 TS4SBL TKY15D MK1KS XDGX2270pp
5 4.000 2.500 1.500 1.181 .787 3.810 .625 .375 1.181 5.4 .827 4 23000 1 TS4SBL TKY15D MK1KS PDFR-GL
Mass
0303DA
Dimensions (inch)
Max.
Depth of Cut
Ramping Angle
3 2.000 2.000 .750 .748 .415 1.875 .313 .187 .600 .9 .827 9 30000 1 TS4SBL TKY15D MK1KS
AXD7000UR0203A
.031
Stock
a
Insert Corner
Number of Teeth
A Holders
z
z
Order Number
Re
B Holders
Geometry
Type
y ARBOR TYPE
& 5"
T :+26 +27
I :+11
Coolant thru
Set Bolt
HSCU37513H
62516H
75016H
MBAU75016H
*
Insert
Anti-seize
Insert
Clamp Torque (lbf-in) : TS4SBL=31
MILLING
Number of Teeth
Max.
Depth of Cut
Ramping Angle
ap
(min-1)
Insert Screw
Wrench
Anti-seize
Lubricant
Insert
.031 AXD7000UR202SA20SA
2 1.250 6.000 2.000 1.250 .827 19
41000
TS4SB
TKY15D
MK1KS
242SA24SA
2 1.500 7.000 3.000 1.500 .827 13
36000
TS4SBL
TKY15D
MK1KS
XDGX2270pp
PDFR-GL
.157 AXD7000UR202SA20SB
.197
242SA24SB
2 1.250 6.000 2.000 1.250 .803 18
41000
TS4SB
TKY15D
MK1KS
2 1.500 7.000 3.000 1.500 .803 11
36000
TS4SBL
TKY15D
MK1KS
Order Number
Stock
Re
Insert Corner
Max.
Spindle
Speed
.125
Dimensions (inch)
D1
L1
L2
D4
Clamp Torque (lbf-in) : TS4SB=31, TS4SBL=31
*
K056
B Holders A Holders
Type
y SHANK TYPE
XDGX2270pp
PDFR-GL
Fig.2
Fig.1
Cutter Diameter
D1
& 50, &63
METRIC Standard
& 80
For metric arbors
50 50 22 20 11 45 10.4 6.3 17 0.4 21
9 30000 1 TS4SBL TKY15D MK1KS
0.8
-063A03RA
63 50 22 20 11 45 10.4 6.3 17 0.5 21
-080A04RA
80 63 27 23 13 63 12.4 7
20 1.2 21
3.2
-100A05RA
5 100 63 32 26 17 70 14.4 8
26 1.8 21
-125B06RA
6 125 63 40 40 56 90 16.4 9
2.7 21
AXD7000-050A03RB
3 16000 2 TS4SBL TKY15D MK1KS XDGX2270pp

50 50 22 20 11 45 10.4 6.3 17 0.4 20.4 8 30000 1 TS4SBL TKY15D MK1KS PDFR-GL
4.0
-063A03RB
63 50 22 20 11 45 10.4 6.3 17 0.5 20.4 6 25000 1 TS4SBL TKY15D MK1KS
-080A04RB
80 63 27 23 13 63 12.4 7
20 1.2 20.4 4 23000 1 TS4SBL TKY15D MK1KS
5.0
-100A05RB
5 100 63 32 26 17 70 14.4 8
26 1.8 20.4 3 19000 1 TS4SBL TKY15D MK1KS
-125B06RB
6 125 63 40 40 56 90 16.4 9
2.7 20.4 2 16000 2 TS4SBL TKY15D MK1KS
Max.
Spindle
Speed
Type (Fig.)
AXD7000-050A03RA
Mass
D1 L1 D9 L7 D8 D12 W1 L8 D11 (kg) ap % (min-1)
Stock
Number of Teeth
Type
z
z
A Holders
Dimensions (mm)
HSC10030H
12035H
16040H
MBA20040H
Order Number
Re
B Holders
& 125
Geometry
Insert Corner
y ARBOR TYPE
& 100
T :+26 +29
I :+11
Max.
Depth of Cut
Ramping Angle
C H :0
A.R :+11
R.R :+26 +29
Set Bolt
*
Insert
Anti-seize
Insert
(Note 3) Note for inserts with a corner radius of 3.0 and above, as corner radius increases the L1 dimension decreases.
METRIC Standard
Max.
Depth of Cut
Ramping Angle
ap
(min-1)
32 21
19
41000
TS4SB
TKY15D
MK1KS
42 21
13
36000
TS4SBL
TKY15D
MK1KS
32 170 80
32 20.4 18
41000
TS4SB
TKY15D
MK1KS
40 170 80
42 20.4 11
36000
TS4SBL
TKY15D
MK1KS
D1
0.8 AXD7000R322SA32SA
32 170 80
R402SA42SA
3.2
4.0 AXD7000R322SA32SB
40 170 80
R402SA42SB
5.0
Stock
Number of Teeth
Max.
Spindle
Speed
Type
Re
Order Number
B Holders A Holders
Insert Corner
y SHANK TYPE
Dimensions (mm)
L1
L2
D4
MILLING
*
Insert Screw
Wrench
Anti-seize
Lubricant
Insert
XDGX2270pp
PDFR-GL
(Note 2) When using the tool at high spindle speeds, ensure that the tool and chuck are correctly balanced.
(Note 3) Note for inserts with a corner radius of 3.0 and above, as corner radius increases the L1 and L2 dimensions decreases.
INSERTS
K057
SPARE PARTS
M001
TECHNICAL DATA
N001
K057
MILLING
Fig.2
Fig.1
Cutter Diameter
D1
& 50, &63
METRIC Standard
& 80
For inch arbors
C H :0
A.R :+11
R.R :+26 +29
R10005DA
31.75
5 100 63 [ "] 32 17 70 12.7
1.25
8 26 1.8 21
R12506EA
38.1
6 125 63 [ "] 40 56 90 15.9 10 2.7 21
1.5
0.8
3.2
Max.
Spindle
Speed
L7 D8 D12 W1 L8 D11 (kg) ap % (min-1)
Type (Fig.)
6 20 1.2 21
D9
Mass
25.4
80 63 [ "] 26 13 63 9.5
1.0
D1 L1
[inch]
Max.
Depth of Cut
Ramping Angle
Dimensions (mm)
*
Insert
Anti-seize
25.4
80 63 [ "] 26 13 63 9.5
1.0
6 20 1.2 20.4 4 23000 1 TS4SBL TKY15D MK1KS

8 26 1.8 20.4 3 19000 1 TS4SBL TKY15D MK1KS
AXD7000R08004CB
R10005DB
31.75
5 100 63 [ "] 32 17 70 12.7
1.25
R12506EB
38.1
6 125 63 [ "] 40 56 90 15.9 10 2.7 20.4 2 16000 2 TS4SBL TKY15D MK1KS
1.5
4.0
5.0
Stock
Type
z
z
AXD7000R08004CA
Insert Corner
A Holders
HSC10030H
12035H
16040H
MBA20040H
Order Number
Re
B Holders
& 125
Geometry
Number of Teeth
y ARBOR TYPE
& 100
T :+26 +29
I :+11
Set Bolt
Insert
XDGX2270pp
PDFR-GL
(Note 3) Note for inserts with a corner radius of .118" and above, as corner radius increases the L1 dimension decreases.
MILLING
METRIC Standard
3.2
2
2
3
D1
L1
L2
32
40
50
127
132
137
80
85
90
Ramping Angle
04002A-H63A
05003A-H63A
A Holders
0.8 AXD7000R03202A-H63A
Dimensions (mm)
Max.
Depth of Cut
Re
Number
of Teeth
Order Number
Stock
Type
Insert Corner
y HSK63A SHANK TYPE (A Holders)

Max.
Spindle
Speed
ap
(min-1)
21
21
21
19
13
9
41000
36000
30000
*
Insert
Screw
TS4SB
TS4SBL
TS4SBL
Anti-seize
Insert
Lubricant
TKY15D MK1KS
XDGX2270pp
TKY15D MK1KS
PDFR-GL
TKY15D MK1KS
Wrench
(Note 2) Note for inserts with a corner radius of .118" and above, as corner radius increases the L1 and L2 dimensions decreases.
(Note 3) There is no data chip hole.
K058

INSERTS
N
Work Material
: Stable Cutting
Non-Ferrous Metal
TF15
Class
Honing
LC15TF
Order Number
: Unstable Cutting
Honing :
F : Sharp
Dimensions (inch)
Stock
Coated Carbide
Shape
: General Cutting
L1
L4
S1
F1
Geometry
Re
XDGX227008PDFR-GL G F
1.181 .886 .276 .079 .031
227016PDFR-GL G F
1.181 .886 .276 .047 .063
227020PDFR-GL G F
1.181 .886 .276 .031 .079
227024PDFR-GL G F
1.181 .886 .276 .016 .094
227030PDFR-GL G F
1.134 .886 .276 .031 .118
227032PDFR-GL G F
1.134 .886 .276 .024 .125
227040PDFR-GL G F
1.083 .886 .276 .035 .157
227050PDFR-GL G F
1.063 .886 .276 .016 .197

Holder
Insert
Corner
Radius
(Re)
A Holder
B Holder
AXD7000URppppppppA
AXD7000URpppppA
AXD7000URppppA
AXD7000URppppppppB
AXD7000URpppppB
AXD7000URppppB
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
227008PDFR-GL 227016PDFR-GL 227020PDFR-GL 227030PDFR-GL 227032PDFR-GL 227040PDFR-GL 227050PDFR-GL

y SHOULDER MILLING
Insert
Grade
Width
of Cut
ae
(inch)
Cutting
Speed
vc
(SFM)
0.25D1
3280
(655 9840)
0.5D1
3280
(655 9840)
0.75D1
3280
(655 9840)
Width
of Cut
ae
(inch)
Cutting
Speed
vc
(SFM)
Depth of
Cut
ap
(inch)
D1
3280
(655 9840)
.197
.197 .394
.394 .591
.591 .787
Aluminum Alloy
LC15TF
TF15
Depth of
Cut
ap
(inch)
.197
.197 .394
.394 .591
.591 .787
.197
.197 .394
.394 .591
.591 .787
.197
.197 .394
.394 .591
.591 .787

Cutting Edge Diameter D1 Cutting Edge Diameter D1
&1.250"
&1.500"
.014
.012
.010
.008
.014
.012
.010
.008
.012
.010
.008
.006
Cutting Edge Diameter D1

&2.000" &3.000"
.016
.014
.012
.010
.014
.012
.010
.008
.012
.010
.008
.006
.016
.014
.012
.010
.016
.014
.012
.010
.014
.012
.010
.008
MILLING
Work Material
y SLOT MILLING
Work Material
N
Aluminum Alloy
Insert
Grade
LC15TF
TF15

Cutting Edge Diameter D1 Cutting Edge Diameter D1
&1.250"
&1.500"
.010
.008
.006
.004
Cutting Edge Diameter D1

&2.000" &3.000"
.012
.010
.008
.006
.014
.012
.010
.008
(Note 1) The above cutting conditions are determined based on high workpiece and machine rigidity,
where no vibration occurred. If vibrations occur make adjustments according to the machining conditions.
(Note 2) Note, vibrations may occur in the following conditions.
When using long tool overhang.
When pocket machining corner radii.
When the workpiece has poor clamping rigidity or when the machine rigidity or workpiece rigidity is low,
vibrations can occur easily. If so, reduce cutting conditions such as width and depth of cut and feed per tooth.
SPARE PARTS
M001
TECHNICAL DATA
N001
K059
MILLING
a HELICAL CUTTING
a RAMPING
Blind holes,
Flat bottom
Through holes
Pitch
(P)
Pitch
(P)
Hole
diameter
(DH)
Hole
diameter
(DH)
RAMPING/HELICAL CUTTING
Holder
Type
Ramping
Helical Milling (Blind Hole, Flat Bottom)
Cutting Edge
Minimum *1)
Maximum *2) Maximum
Maximum *3) Maximum
Maximum
Diameter
Pitch
Pitch
Hole Diameter
Hole Diameter
Ramping Angle Distance
D1
L
P max.
P max.
DH max.
DH min.
(inch)
(inch)
%
(inch)
(inch)
(inch)
(inch)
1.250
1.500
2.000
3.000
1.250
1.500
2.000
3.000
19
13
9
5
18
11
8
4
2.40
3.58
5.22
9.45
2.54
4.25
5.88
11.82
2.413
2.913
3.913
5.913
2.161
2.661
3.661
5.661
.866
.748
.630
.591
.630
.591
.512
.394
2.272
2.772
3.772
5.772
2.106
2.606
3.606
5.606
.827
.709
.630
.591
.630
.591
.512
.394
Helical Milling (Through Hole)

Maximum
Minimum
Pitch
Hole Diameter
P max.
DH min.
( inch )
(inch)
1.614
2.126
3.110
5.118
1.614
2.126
3.110
5.118
.315
.354
.394
.433
.276
.315
.354
.315
(Note) The recommended ramping or drilling feed is .002 IPT or less.

1 Using the maximum ramping angle, the distance to reach the maximum depth of cut is as follows:
L= (maximum depth of cut ap/tan %). Maximum depth of cut A type is .827", B type is .803".
2 The maximum diameter when machining a blind hole with a at face using a corner radius of .031" for A type and .157" for B type.
For other corner radii, use to following formula.
{(cutting edge diameter D1) - (corner radius Re) - .012"}x 2
3 The minimum diameter when machining a blind hole with a at face using a corner radius of .031" for A type and .157" for B type.
For other corner radii, use to following formula.
{(cutting edge diameter D1) - (corner radius Re) - (width of wiper edged F1) - .004"}x 2
*
*
*
y MAX.DRILLING DEPTH
Max.Drilling Depth (inch)
(inch)
.031
A
.197
.125
B
K060
Insert
Corner R
Re
MILLING
Holder Type
.157
.197
.157
AXD7000 can be effectively used for

pocket machining without the need
for a prepared hole.
especially important to ensure overall tool safety.
Do not use damaged or worn clamp screws.
Cutting Edge Diameter D1(inch)
1.250"
1.500" 5.000"
Clamp Screw Number
TS4SB
TS4SBL
Overall Length L(inch)
.353
.413
Clamp Torque (lbf-in)
31
31
First

a The maximum allowable spindle speeds are shown in Table 1. Ensure that the cutter operates under the

Second
Figure 1

1.250"
1.500"
2.000"
2.500"
3.000"
4.000"
5.000"
41000
36000
30000
25000
23000
19000
16000
that the balance quality (with the arbor or milling chuck) conforms to G6.3 or better based on ISO1940. It is also recommended to replace the clamp screws with
The balance quality of the holder (without inserts and clamp screws) is G6.3 or better at 10000min-1.
(Table 2) Maximum spindle speed when balancing with the arbor or milling chuck has not been achieved
1.250"
1.500"
2.000"
2.500"
3.000"
4.000"
5.000"
9500
7600
6000
4800
3800
3000
2400
MILLING
K061
MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
<ALUMINUM ALLOY FOR DIFFICULT-TO-CUT MATERIAL CUTTING>
Finishing
Roughing
BXD4000
Light Alloy
Cast Iron

a Low resistance inserts & high rigidity body.
a The Anti Fly Insert mechanism
guarantees secure high-revolution milling.
Order Number

.125
.157
B Holders
A Holders
Re
.016
.197
Stock
Insert
Corner
BXD4000R162SA12S
162SA16S
202SA20S
243SA20S
BXD4000R162SA12SB
162SA16SB
202SA20SB
243SA20SB
a
a
a
a
a
a
a
a
Number of Teeth
Type
y STRAIGHT SHANK TYPE
D1
L1
D4
L2
ap
2
2
2
3
2
2
2
3
1.000
1.000
1.250
1.500
1.000
1.000
1.250
1.500
6.000
6.000
6.000
6.000
6.000
6.000
6.000
6.000
.750
1.000
1.250
1.250
.750
1.000
1.250
1.250
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
.591
.591
.591
.591
.591
.591
.591
.591
20
20
13
10
20
20
13
10
Max.
Ramping
Depth
Angle
of Cut
Dimensions (inch)
1 You need to balance the tool and holder together so that it conrms to G40 or higher standards.
*
Max.
Spindle Speed
(min-1)
Balance
G40 *1 Insert
Unknown Balanced Screw Wrench
12000
38000 TS4SL TKY15W
12000
38000 TS4SL TKY15W
9500
33000 TS4SL TKY15W
7600
29000 TS4SL TKY15W
12000
38000 TS4SL TKY15W
12000
38000 TS4SL TKY15W
9500
33000 TS4SL TKY15W
7600
29000 TS4SL TKY15W
2 Clamp Torque (lbf-in) : TS4SL=35

Work
Material
P
M
K
N
S
Steel
: Stable Cutting
Stainless Steel
Cast Iron
Dimensions (inch)
Lower Cutting
Resistance Type
K062
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
F
F
F
F
F
F
F
F
F
E
E
E
E
E
E
E
E
E
F
F
TF15
XDGT1550PDFR-G04
1550PDFR-G08
1550PDFR-G12
1550PDFR-G16
1550PDFR-G20
1550PDFR-G30
1550PDFR-G32
1550PDFR-G40
1550PDFR-G50
XDGT1550PDER-G04
1550PDER-G08
1550PDER-G12
1550PDER-G16
1550PDER-G20
1550PDER-G30
1550PDER-G32
1550PDER-G40
1550PDER-G50
XDGT1550PDFR-GL04
1550PDFR-GL08
MILLING
G breaker
Class
Honing
VP15TF
LC15TF
Coated Carbide
Order Number
L1
.866
.866
.866
.866
.854
.787
.787
.748
.709
.866
.866
.866
.866
.854
.787
.787
.748
.709
.866
.866
a
a
s
a
a
a
a
a
a
a
a

: Unstable Cutting
Honing :
E : Round F : Sharp
Non-Ferrous Metal
Shape
: General Cutting
L4
S1
F1
Re
.630
.630
.630
.630
.630
.630
.630
.630
.630
.630
.630
.630
.630
.630
.630
.630
.630
.630
.630
.630
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.059
.043
.028
.016
.008
.024
.016
.020
.016
.059
.043
.028
.016
.008
.024
.016
.020
.016
.059
.043
.016
.031
.047
.063
.079
.118
.125
.157
.197
.016
.031
.047
.063
.079
.118
.125
.157
.197
.016
.031
Geometry
D1
Insert
Corner
Order Number
BXD4000R1503
0203
0204
2504
0305
0406
BXD4000R1503B
0203B
0204B
2504B
0305B
0406B
.016
.125
.157
A Holders
Re
B Holders
Stock
Type
y ARBOR TYPE
.197
Number of Teeth
C H :0
A.R :+15
R.R :+13 +16
1.5
2
2.5
3
4
T :+13 +16
I :+15
HSCU25014H
37513H
37513H
50014H
75016H
2
D1
L1
D9
L7
D8
*
Max.
Spindle Speed
(min-1)
Balance
G40 *1 Insert Wrench
% Unknown Balanced
Screw
10
7600 29000 TS4SL TKY15W
Max.
Ramping
Depth
Angle
of Cut
Dimensions (inch)
W1
ap
L8
3
3
1.500 1.969
2.000 1.969
.500
.750
.630 .276 .250 .156

.748 .415 .313 .187
.591
.591
6000
24000 TS4SL TKY15W
2.000 1.969
.750
.748 .415 .313 .187
.591
6000
24000 TS4SL TKY15W
2.500 1.969
.750
.748 .415 .313 .187
.591
4800
5
6
3.000 1.969 1.000 1.024 .539 .375 .219

4.000 2.480 1.500 1.181 .787 .625 .375
.591
.591
3
3
3800
3000
21000 TS4SL TKY15W

19000 TS4SL TKY15W
16000 TS4SL TKY15W
3
3
1.500 1.969
2.000 1.969
.500
.750
.630 .276 .250 .156

.748 .415 .313 .187
.591
.591
10
7
7600
6000
29000 TS4SL TKY15W

24000 TS4SL TKY15W
2.000 1.969
.750
.748 .415 .313 .187
.591
6000
24000 TS4SL TKY15W
2.500 1.969
.750
.748 .415 .313 .187
.591
4800
5
6
3.000 1.969 1.000 1.024 .539 .375 .219

4.000 2.480 1.500 1.181 .787 .625 .375
.591
.591
3
3
3800
3000
21000 TS4SL TKY15W

19000 TS4SL TKY15W
16000 TS4SL TKY15W
a
a
need to balance the tool and holder together so that it conrms to G40 or higher standards.
*12 You
Clamp Torque (lbf-in) : TS4SL=35
*

~ A Holder
~ B Holder
BXD4000RoooooooA
BXD4000RoooooooB
Holder
.016"
.031"
.047"
.063"
.079"
.118"
.125"
.157"
.197"
Insert
Corner Radius
(Re)
XDGT........-G04 XDGT........-G08 XDGT........-G12 XDGT........-G16 XDGT........-G20 XDGT........-G30 XDGT........-G32 XDGT........-G40 XDGT........-G50

MILLING

Hardness
Grade
Cutting Speed (SFM)
Mild Steel
< 180HB
VP15TF
590 (490 655)
.006 (.004 .008)
Carbon Steel
Alloy Steel
< 280HB
VP15TF
490 (390 655)
.006 (.004 .008)
280 350HB
VP15TF
460 (390 525)
.006 (.004 .008)
Stainless Steel
< 270HB
VP15TF
460 (390 525)
.008 (.004 .012)
Aluminum Alloy
TF15
3280 (655 9840)
.012 (.004 .020)
Titanium Alloy
VP15TF
130 (100 195)
.004 (.004 .012)
VP15TF
100 (65 130)
.006 (.004 .008)
Work Material
The gure above are the guidelines for conditions of general cutting by a standard type tool.
The conditions vary depending on machine strength, the length of overhang, and work clamping conditions.
Please adjust table feed when using long shank type tool.
SPARE PARTS
M001
TECHNICAL DATA
N001
K063
MILLING
Fig.2
Fig.1
Fig.3
Cutter Diameter
D1
METRIC Standard
&80
5.0
s
s
s
s
s
s
s
s
s
s
s
0.3
0.4
0.7
1.1
2.0
2.8
0.3
0.4
0.7
1.1
2.0
2.8
15
15
15
15
15
15
15
15
15
15
15
15
9
6
5
3
3
2
9
6
5
3
3
2
29000
24000
21000
19000
16000
14000
29000
24000
21000
19000
16000
14000
Max.
Spindle
Speed
Mass
40
50
63
80
100
125
40
50
63
80
100
125
Ramping Angle

4.0
A Holders
B Holders
3.2
3
4
5
5
6
7
3
4
5
5
6
7
Dimensions (mm)
Max.
Spindle
Speed
L1 D9 L7 D8 D12 W1
L8
D11 (kg) ap % (min-1)
50
50
50
50
63
63
50
50
50
50
63
63
5.6
6.3
6.3
7
8
9
5.6
6.3
6.3
7
8
9

17
17
20
26

17
17
20
26
16
22
22
27
32
40
16
22
22
27
32
40
18
20
20
23
26
40
18
20
20
23
26
40
M8
11
11
13
17
56
M8
11
11
13
17
56
32
41
50
60
70
80
32
41
50
60
70
80
8.4
10.4
10.4
12.4
14.4
16.4
8.4
10.4
10.4
12.4
14.4
16.4
x
c
1
2
2
2
2
3
1
2
2
2
2
3
*
Insert
Screw
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
Wrench
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
Insert
XDGT1550
PDpR-Gpp
XDGT1550
PDpR-GLpp
XDGT1550
PDpR-Gpp
METRIC Standard
For inch arbors
0.4
3.2
4.0
B Holders A Holders
Re
5.0
BXD4000R08005CA
10006DA
12507EA
BXD4000R08005CB
10006DB
12507EB
s
s
s
s
s
s
5
6
7
5
6
7
Dimensions (mm)
D1 L1 L7 L8 D8 W1
80
100
125
80
100
125
50
63
63
50
63
50
26
32
40
26
32
40
6
8
10
6
8
10
13
17
56
13
17
56
9.5
12.7
15.9
9.5
12.7
15.9
[inch]
D9
25.4 [1.0"]
31.75 [1.25"]
38.1 [1.5"]
25.4 [1.0"]
31.75 [1.25"]
38.1 [1.5"]
D11 D12 (kg) ap % (min-1)
20
26

20
26
60
70
80
60
70
80
1.1
2.0
2.8
1.1
2.0
2.8
15
15
15
15
15
15
3
3
2
3
3
2
19000
16000
14000
19000
16000
14000
Type (Fig.)
Order Number
Number of Teeth
Insert
Corner
Stock
y ARBOR TYPE
Type
MILLING
0.4
BXD4000-040A03RA
-050A04RA
-063A05RA
-080A05RA
-100A06RA
-125B07RA
BXD4000-040A03RB
-050A04RB
-063A05RB
-080A05RB
-100A06RB
-125B07RB
D1
&125
Ramping Angle
Re
T :+8 +16
I :+11 +15
Max. Depth
of Cut
Order Number
Stock
Insert
Corner
Number of Teeth
Type
y ARBOR TYPE
&100
Mass
C H :0
A.R :+10 +15
R.R :+8 +10
HFF08043H
HSC10030H
12035H
16040H
MBA20040H
Max. Depth
of Cut
For metric arbors
Geometry
Type (Fig.)
&40
&50, &63
Set Bolt
2
2
3
2
2
3
*
Insert
Screw
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
Wrench
(Note 1) The maximum spindle speeds stated above are based on ISO15641.
(Note 2) When using the tool at high spindle speeds, please pay special attention to the balancing. The whole tool assembly should
be balanced according to G6.3 based on ISO1940 quality grades.
*
K064
Insert
TKY15W XDGT1550
pR-Gpp
TKY15W PD
XDGT1550
TKY15W PDpR-GLpp
TKY15W
XDGT1550
TKY15W
PDpR-Gpp
TKY15W
Fig.1 Straight Shank
Fig.2 Offset Shank
METRIC Standard
Order Number
BXD4000R201SA20SA
252SA25SA
282SA25SA
322SA32SA
352SA32SA
403SA32SA
403SA42SA
BXD4000R252SA25LA
322SA32LA
BXD4000R282SA25ELA
352SA32ELA
403SA32ELA
BXD4000R201SA20SB
252SA25SB
282SA25SB
322SA32SB
352SA32SB
403SA32SB
403SA42SB
BXD4000R252SA25LB
322SA32LB
BXD4000R282SA25ELB
352SA32ELB
403SA32ELB
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
D1
ap
L1
L2
D4
(min-1)
Type (Fig.)
Long
Extra
Long
5.0
Stock
Shank Type
Standard
4.0
B Holders
Extra
Long
3.2
Number of Teeth
0.4
A Holders
Re
Standard
Insert
Corner
Long
Type
y SHANK TYPE
1
2
2
2
2
3
3
2
2
2
2
3
1
2
2
2
2
3
3
2
2
2
2
3
20
25
28
32
35
40
40
25
32
28
35
40
20
25
28
32
35
40
40
25
32
28
35
40
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
110
125
125
150
150
170
170
170
200
220
250
250
110
125
125
150
150
170
170
170
200
220
250
250
35
50
50
50
50
80
80
80
80
50
50
65
35
50
50
50
50
80
80
80
80
50
50
65
20
25
25
32
32
32
42
25
32
25
32
32
20
25
25
32
32
32
42
25
32
25
32
32
28
20
17
13
11
9
9
20
13
17
11
9
28
20
17
13
11
9
9
20
13
17
11
9
15000
38000
35000
33000
31000
29000
29000
38000
33000
35000
31000
29000
15000
38000
35000
33000
31000
29000
29000
38000
33000
35000
31000
29000
1
1
2
1
2
2
1
1
1
2
2
2
1
1
2
1
2
2
1
1
1
2
2
2
Ramping Max.
Angle Spindle
Speed
Dimensions (mm)
1 You need to balance the tool and holder together so that it conrms to G40 or higher standards.
*
Insert
Screw
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
TS4SL
Wrench
Insert
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
TKY15W
XDGT1550
PDpR-Gpp
XDGT1550
PDpR-GLpp
XDGT1550
PDpR-Gpp
*2 Clamp Torque (lbf-in) : TS4SL=35
especially important to ensure overall tool safety. Do not use damaged or worn clamp screws.
a The maximum allowable spindle speeds are shown in Table 1. Ensure that the cutter operates under the maximum allowable spindle speed.
The maximum allowable spindle speeds for safety purposes are determined in accordance with ISO15641 (Milling Cutters for high speed machiningSafety requirements).
MILLING

.750"
15000
.950"
38000
1.100" 1.250" 1.350" 1.500" 2.000" 2.500" 3.000" 4.000" 5.000"

35000
33000
31000
29000
24000
21000
19000
16000
14000
20mm with one tooth balancing is necessary to adjust sensitively.

that the balance quality (with the arbor or milling chuck) conforms to G40 or better based on ISO1940. It is also recommended to replace the clamp screws with
The balance quality of the holder (without inserts and clamp screws) is G40 or better at 10000min-1
*(
Table 2) Maximum spindle speed when balancing with the arbor or milling chuck has not been achieved
.750"
.950"
15000
12000
1.100" 1.250" 1.350" 1.500" 2.000" 2.500" 3.000" 4.000" 5.000"

10800
9500
8700
7600
6000
4800
3800
3000
2400
INSERTS
K062
SPARE PARTS
M001
TECHNICAL DATA
N001
K065
MILLING
SHOULDER MILLING
BAP300
Light Alloy
Cast Iron
Roughing
Fig.1
(Max. Depth of Cut)
Fig.2
Fig.3
a Inserts with various chipbreakers
and grades are available.
y SHANK TYPE
Order Number
Stock
R
Number of Teeth
D1
L2
Max.
Depth
of Cut
ap
Insert Screw
Wrench
BAP300R081W08
.500
2.781
.500
1.000
.354
TS25
TKY08F
102W10
.625
3.500
.625
1.000
.354
TS25
TKY08F
122W12
.750
4.000
.750
1.250
.354
TS25
TKY08F
123W12
.750
4.000
.750
1.250
.354
TS25
TKY08F
164W12
1.000
4.000
.750
1.250
.354
TS25
TKY08F
164W16
1.000
4.500
1.000
1.250
.354
TS25
TKY08F
205W20
1.250
5.000
1.250
1.750
.354
TS25
TKY08F
246W20
1.500
5.000
1.250
1.750
.354
TS25
TKY08F
Dimensions (inch)
L1
D4
MILLING
K066

Type
(Fig.)
*
Insert
APG/MT1135
PDpR-pp
INSERTS
Steel
: Stable Cutting
Stainless Steel
Cast Iron
Hardened Materials
Coated
M E
1135PDER-H2
M E
1135PDER-H4
M E
1135PDER-H6
M E
APMT1135PDER-M0 M E
1135PDER-M1 M E
1135PDER-M2 M E
APGT1135PDFR-G2
.433
.250
.138
.059
.016
.433
.250
.138
.047
.031
.433
.250
.138
.016
.063
.433
.250
.138
.016
.094
.433
.250
.138
.071
.008
.433
.250
.138
.059
.016
.433
.250
.138
.047
.031
.433
.250
.138
.047
.031
G F
HTi10
F7030
UTi20T
APMT1135PDER-H1
NX4545
H breaker
G breaker
: Unstable Cutting
Dimensions (inch)
Cermet Carbide
VP15TF
Order Number
F7010
Shape
M breaker
: General Cutting
Honing :
E : Round F : Sharp
Non-Ferrous Metal
Class
Honing
Work
Material
P
M
K
N
H
L1
L2
S1
F1
Re
Geometry

P
Mild Steel
Hardness
Grade
Breaker
Cutting Mode
Cutting Speed (SFM)
< 180HB
NX4545
VP15TF/F7030
M
M
Finish Cutting
General Cutting
800 1200
NX4545
Finish Cutting
180 280HB
VP15TF/F7030
General Cutting
F7030
Unstable Cutting
Carbon Steel
Alloy Steel
280 350HB
NX4545
Finish Cutting
VP15TF/F7030
VP15TF/F7030
M
H
General Cutting
Unstable Cutting
700 1000
600 900
600 700
Feed per Tooth

(inch/tooth)
.004 (.002 .006)
.006 (.004 .008)
.003 (.002 .004)
.006 (.004 .008)
.006 (.004 .008)
.003 (.002 .004)
.006 (.004 .008)
.008 (.004 .010)
.006 (.004 .008)
.004 (.002 .006)
Stainless Steel
< 200HB
VP15TF/F7030
VP15TF
M
H
General Cutting
General Cutting
300 700
Gray Cast Iron
Tensile Strength
< 350MPa
VP15TF
General Cutting
700 1000
.006 (.004 .008)
Tensile Strength
< 450MPa
VP15TF
General Cutting
600 800
.006 (.004 .008)
Tensile Strength
500 800MPa
VP15TF
General Cutting
500 700
.004 (.002 .006)
HTi10
General Cutting
VP15TF
General Cutting
1000 3000
100 300
.004 (.002 .006)
Ductile Cast Iron
N
H
Aluminum Alloy
Hardened Steel

40 55HRC
MILLING
Work Material
.008 (.004 .012)
SPARE PARTS
M001
TECHNICAL DATA
N001
K067
MILLING
DEEP SHOULDER
MILLING
Roughing
BAP300
Light Alloy
Cast Iron
LONG CUTTING EDGE
Fig.1
Fig.2
Fig.3 Combination Shank
a Inserts with various chipbreakers
and grades are available.
y LONG EDGE TYPE
BAP300R1204WL12
1608WL16
2012WL20
2414WL24
3227WL32
a
a
a
a
a
Number of Teeth
Stock
Order Number
Number of Flute
1 4
2 8
2 12
2 14
3 27
D1
L1
D4
L2
Max.
Depth
of Cut
ap
.750
1.000
1.250
1.500
2.000
4.375
5.250
5.625
6.250
6.750
.750
1.000
1.250
1.500
2.000
1.625
2.000
2.375
3.000
3.500
1.024
1.339
1.693
2.008
2.638
Dimensions (inch)
Type
(Fig.)
2
1
1
1
3
*
Insert Screw
TS25
TS25
TS25
TS25
TS25
Wrench
TKY08F
TKY08F
TKY08F
TKY08F
TKY08F
Insert
APG/MT1135
PDpR-p1/p2

INSERTS
Cast Iron
HTi10
NX4545
a
a
UTi20T
VP15TF
M E
L1
L2
S1
F1
Re
.433
.433
.250
.250
.138
.138
.059
.047
.016
.031
.433
.433
.433
.250
.250
.250
.138
.138
.138
.071
.059
.047
.008
.016
.031
.433
.250
.138
.047
.031
a
a
a
G F

: Unstable Cutting
Dimensions (inch)
Cermet Carbide
M E
APMT1135PDER-M0 M E
1135PDER-M1 M E
1135PDER-M2 M E
APGT1135PDFR-G2
Coated
F7030
APMT1135PDER-H1
1135PDER-H2
Class
Honing
Hardened Materials
H breaker
: General Cutting
Honing :
E : Round F : Sharp
Non-Ferrous Metal
Order Number
G breaker
: Stable Cutting
Stainless Steel
Shape
M breaker
K068
Steel
F7010
MILLING
Work
Material
P
M
K
N
H
Geometry

Work Material
Mild Steel
Hardness
Grade
Breaker
Cutting Mode
Cutting Speed
(SFM)
< 180HB
NX4545
VP15TF/F7030
M
M
Finish Cutting
General Cutting
800 1200
NX4545
Finish Cutting
180 280HB
VP15TF/F7030
General Cutting
F7030
Unstable Cutting
Carbon Steel
Alloy Steel
280 350HB
.004 (.002 .006)

.006 (.004 .008)
.003 (.002 .004)
.006 (.004 .008)
.006 (.004 .008)
.003 (.002 .004)
NX4545
Finish Cutting
VP15TF/F7030
VP15TF/F7030
M
H
General Cutting
Unstable Cutting
VP15TF/F7030
VP15TF
F7030
M
H
H
General Cutting
General Cutting
Unstable Cutting
300 500
.006 (.004 .008)

.008 (.004 .010)
.006 (.004 .008)
.004 (.002 .006)
.008 (.004 .010)
600 900
600 700
300 700
Stainless Steel
< 200HB
Gray Cast Iron
Tensile Strength
< 350MPa
VP15TF
General Cutting
700 1000
.006 (.004 .008)
Tensile Strength
< 450MPa
VP15TF
General Cutting
600 800
.006 (.004 .008)
Tensile Strength
500 800MPa
VP15TF
General Cutting
500 700
.004 (.002 .006)
1000 3000
100 300
.008 (.004 .012)

.004 (.002 .006)
Ductile Cast Iron
N
H
700 1000
Feed per Tooth

(inch/tooth)
Aluminum Alloy
Hardened Steel
HTi10
General Cutting
> 40HRC
VP15TF
General Cutting
y CUTTING PERFORMANCE
Cutting Width
Grade : UTi20T
Cutting Depth (inch)
Cemented carbide / Coated carbide
Shoulder Milling
Cutting Depth
FOR BAP300 LONG CUTTING EDGE TYPE
Cutting Width
MILLING
(Note1) In each of the above graphs cutting performance is shown

for carbon steel (AlSI1049). In case of alloy steels, reduce the
conditions by 20 30%.
(Note2) In the case of deep slot milling air blow should be used.
(Note3) The diameter "D1" is taken from the tools peripheral cutting
edge.
SPARE PARTS
M001
TECHNICAL DATA
N001
K069
MILLING
DEEP SHOULDER
MILLING
SPX
Light Alloy
Cast Iron
Roughing
a CAT50 shank
General Steel Alloy Tool Steel Hardened Steel
ap(Max. Depth of Cut)
a Straight shank (Combination type)

a The wavy cutting edge
helps to reduce cutting

resistance.
a Suitable for heavy machining
y SHANK TYPE
Straight Shank
(Combination)
SPX4R3224CAT50NS
Stock
Order Number
Number of Flute
CAT50
Shank
Type
Number
of Teeth
24
Number of Insert
Dimensions (inch)
Total
D1
L1
D4
Bottom Cutting Edge A Bottom Cutting Edge B Peripheral Cutting Edge
L2
ap
JPMX
190412- oo
MPMX
120412- oo
SPMX
120408- oo
2.000 11.000
7.000 4.300
20
2.000 13.000
9.000 6.200
30
11.000 8.100
40
4R3234CAT50NM
4R3244CAT50NL
44
2.000 15.000
16
1.969
7.091 2.000
3.937 2.835
12
4R05024WNS
24
1.969
8.661 2.000
5.512 4.331
20
4R05034WNM
34
1.969 10.630 2.000
7.480 6.181
30
4R05044WNL
44
1.969 12.598 2.000
9.449 8.071
40
SPX4R05016WNES
34
L8
D1
D8
W1
D9
L7

L1
y SHELL TYPE
Order Number
Number
of Teeth
R Flutes Total
Set Bolt
& 2.500"
HSCUF50028
62528
Number of Insert
Dimensions (inch)
D1
L1
D9
L7
D8
D7
Geometry
D1
& 3.000"
Stock
MILLING
W1
L8
ap
JPMX
140412- oo
MPMX
120412- oo
SPMX
120408- oo
SPX4UR2524CA22A
24
2.500 3.500 1.000 1.339 .539 2.375 .375 .219 2.280
20
4UR0324DA22A
24
3.000 3.500 1.250 1.654 .669 2.874 .500 .281 2.280
20
(Note) In case of internal coolant supply, please use a face mill arbor with through coolant channels. Regular center-thru or side-thru arbors can't be used.
K070

L8
D1
D8
W1
D9
L7

L1
METRIC Standard
For inch arbors
Stock
Number
of Teeth
Dimensions (mm)
R Flutes Total D1 L1
SPX4R06324CA058A
4R08024DA058A
Set Bolt
& 63mm
HSC12070
16065
& 80mm
y SHELL TYPE
Order Number
D1
s
s
4
4
24
24
D9
L7 D8
Number of Insert
[inch]
D7
Geometry
W1 L8 ap
JPMX
140412- oo
MPMX
120412- oo
SPMX
120408- oo
2
2
2
2
20
20
63 85 25.4 [1.000] 26 13 60
9.5 6 58
80 85 31.75 [1.250] 38 17 76.8 12.7 8 58
L7
D1
D8
W1
D9
L8

L1
METRIC Standard
D1
Set Bolt
& 63mm
HSC12070
16065
For metric arbors

The bore diameter (D9) is equivalent to a metric size.
& 80mm
Number
of Teeth
R Flutes Total
SPX4-063A24A058RA
-080A24A058RA
s
s
4
4
24
24
Number of Insert
Dimensions (mm)
D7
D1
L1
D9
L7
D8
W1
63
80
85
85
27
32
28
40
13 60 12.4
17 76.8 14.4
L8
ap
JPMX
140412- oo
MPMX
120412- oo
SPMX
120408- oo
7
8
58
58
2
2
2
2
20
20
MILLING
Order Number
Stock
ySHELL TYPE
Geometry
SPARE PARTS
*
Holder
SPX
Insert Screw
Wrench
TS55
TKY25D
Insert
JPMX190412-WH
MPMX120412-WH
SPMX120408-WH
JPMX190412-JM
MPMX120412-JM
SPMX120408-JM
K071
MILLING
INSERTS
Dimensions (inch)
S1
Re
a a
.750
.500
.187
.047
140412-WH
a a
.563
.500
.187
.047
MPMX120412-WH
a a
.500
.187
.047
SPMX120408-WH
a a
.500
.187
.031
JPMX190412-JM
a a
.750
.500
.187
.047
140412-JM
a a
.563
.500
.187
.047
MPMX120412-JM
a a
.500
.187
.047
SPMX120408-JM
a a
.500
.187
.031
Bottom Cutting Edge A
Bottom Cutting Edge B
Wavy Cutting Edge Type
D1
Peripheral Cutting Edge
L2
JPMX190412-WH
* Only for use with a shell type holder.
K072
L1
Bottom Cutting Edge A
Straight Cutting Edge Type
MILLING
Order Number
Bottom Cutting Edge B
Shape
Peripheral Cutting Edge
Type
Class
VP15TF
VP20RT
Coated
Geometry
RECOMMENDED CUTTING CONDITIONS (Shank Type)

y CUTTING CONDITIONS FOR SHOULDER MILLING (Number of effective utes is 2.)
Work Material
Hardness
P
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180 350HB
Alloy Tool Steel
< 300HB
Stainless Steel
Cast Iron
< 200HB
Tensile
Strength
<350MPa
Ductile Cast Iron
Tensile
Strength
<800MPa
Titanium Alloy
< 350HB
Insert
Grade/Breaker
VP15TF
WH
VP15TF
JM
VP15TF
WH
VP15TF
JM
VP15TF
WH
VP15TF
JM
VP20RT
WH
VP20RT
JM
VP15TF
WH
VP15TF
JM
VP15TF
WH
VP15TF
JM
VP20RT
WH
VP20RT
JM
Cutting Speed
vc
Width of Cut
ae
Depth of Cut
ap
Feed per Tooth

fz
395
(330 460)
395
(330 460)
260
(230 395)
260
(230 395)
260
(200 330)
260
(200 330)
260
(230 395)
260
(230 395)
330
(260 395)
330
(260 395)
260
(200 330)
260
(200 330)
130
(115 165)
130
(115 165)
<.197
<4D1
.006 .010
<.394
<2D1
.006 .010
<.197
<4D1
.006 .010
<.394
<2D1
.006 .010
<.197
<4D1
.004 .008
<.394
<2D1
.004 .008
<.197
<4D1
.004 .008
<.394
<2D1
.004 .008
<.197
<4D1
.006 .016
<.197
<4D1
.004 .010
<.197
<4D1
.006 .014
<.197
<4D1
.004 .008
<.197
<4D1
.003 .005
<.394
<2D1
.003 .005
(SFM)
(inch)
(inch)
(IPT)
(Note 2) For tools with a cutting edge length of 7.87 or more, please reduce the cutting speed and table feed by 10-20% and the width of cut
by 50%.
(Note 3) If the cutting angle between the tool and workpiece exceeds 90 when machining corners ,Reduce the cutting speed and table feed
by 10-20% and ae by 50%. Also if possible, set a radius cutting path for corners.

Hardness
P
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180 350HB
Alloy Tool Steel
< 300HB
Stainless Steel
Cast Iron
< 200HB
Tensile
Strength
<350MPa
Ductile Cast Iron
Tensile
Strength
<800MPa
Titanium Alloy
< 350HB
Insert
Grade/Breaker
VP15TF
WH
VP15TF
JM
VP15TF
WH
VP15TF
JM
VP15TF
WH
VP15TF
JM
VP20RT
WH
VP20RT
JM
VP15TF
WH
VP15TF
JM
VP15TF
WH
VP15TF
JM
VP20RT
WH
VP20RT
JM
Cutting Speed
vc
Width of Cut
ae
Depth of Cut
ap
Feed per Tooth

fz
200
(165 395)
200
(165 395)
200
(165 330)
200
(165 330)
165
(130 260)
165
(130 260)
200
(165 395)
200
(165 395)
165
(130 260)
165
(130 260)
130
(115 260)
130
(115 260)
115
(100 165)
115
(100 165)
D1
<.394
.004 .010
D1
<.394
.004 .006
D1
<.394
.004 .010
D1
<.394
.004 .006
D1
<.394
.004 .010
D1
<.394
.004 .006
D1
<.394
.004 .010
D1
<.394
.004 .006
D1
<1.969
.006 .010
D1
<1.575
.004 .008
D1
<1.575
.006 .010
D1
<1.181
.004 .008
D1
<.394
.003 .005
D1
<.394
.003 .005
(SFM)
(inch)
(inch)
(IPT)
MILLING
Work Material
K073
MILLING
RECOMMENDED CUTTING CONDITIONS (Shell Type)

y CUTTING CONDITIONS FOR SHOULDER MILLING (Number of effective utes is 4.)
Work Material
Hardness
Insert
Grade/Breaker
< 180HB
VP15TF
JM
P
Mild Steel
Carbon Steel
Alloy Steel
180 350HB
Alloy Tool Steel
< 300HB
Stainless Steel
< 200HB
K
Cast Iron
Tensile
Strength
<350MPa
Ductile Cast Iron
Tensile
Strength
<800MPa
Titanium Alloy
< 350HB
VP15TF
JM
VP15TF
JM
VP20RT
JM
VP15TF
WH
VP15TF
JM
VP15TF
WH
VP15TF
JM
VP20RT
JM
Cutting Speed
vc
(SFM)
395
(330 460)
395
(330 460)
395
(260 425)
330
(260 395)
330
(200 360)
260
(200 330)
460
(330 490)
395
(330 460)
395
(260 425)
330
(260 395)
395
(260 425)
330
(260 395)
330
(200 360)
260
(200 360)
330
(200 395)
260
(200 395)
150
(115 165)
150
(115 165)
Width of Cut
ae
Depth of Cut
ap
Feed per Tooth

fz
<.394
<0.5D1
.006 .012
<.394
>0.5D1
.006 .010
<.394
<0.5D1
.006 .012
<.394
>0.5D1
.006 .010
<.394
<0.5D1
.004 .010
<.394
>0.5D1
.004 .006
<.394
<0.5D1
.004 .010
<.394
>0.5D1
.004 .008
<.394
<0.5D1
.010 .016
<.394
>0.5D1
.010 .016
<.394
<0.5D1
.006 .012
<.394
>0.5D1
.006 .010
<.394
<0.5D1
.008 .014
<.394
>0.5D1
.008 .014
<.394
<0.5D1
.006 .012
<.394
>0.5D1
.006 .012
<.394
<0.5D1
.003 .004
<.394
>0.5D1
.003 .004
(inch)
(inch)
(IPT)
MILLING
Work Material
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180350HB
Alloy Tool Steel
< 300HB
Stainless Steel
< 200HB
K
Cast Iron
Tensile
Strength
< 350MPa
Ductile Cast Iron
Tensile
Strength
< 800MPa
Titanium Alloy
< 350HB
Insert
Grade/Breaker
VP15TF
JM
VP15TF
JM
VP15TF
JM
VP20RT
JM
VP15TF
WH
VP15TF
JM
VP15TF
WH
VP15TF
JM
VP20RT
JM
Cutting Speed
vc
Width of Cut
ae
Depth of Cut
ap
Feed per Tooth

fz
395
(330 460)
330
(260 395)
260
(200 330)
330
(260 460)
260
(200 330)
200
(165 330)
260
(200 330)
200
(165 330)
260
(200 330)
200
(165 330)
260
(200 330)
200
(165 330)
130
(115 165)
D1
<0.25D1
.006 .010
D1
<0.25D1
.006 .010
D1
<.394
.004 .008
D1
<.394
.004 .006
D1
<0.25D1
.004 .010
D1
<0.6D1
.004 .008
D1
<0.25D1
.004 .008
D1
<0.6D1
.004 .006
D1
<0.25D1
.004 .010
D1
<0.5D1
.004 .008
D1
<0.25D1
.004 .008
D1
<0.5D1
.004 .006
D1
<0.25D1
.002 .004
(SFM)
(inch)
(inch)
(IPT)
K074
Memo
K075
MILLING
DEEP SHOULDER
MILLING
<CUTTING FOR TITANIUM ALLOY>
Roughing
VFX
W1
ap (Max.Depth of Cut)
L1
a High efciency milling
titanium alloys.
a On-edge style inserts
with high strength cutting

edge.
VFX6-063A04A031R
-063A04A060R
-080A05A031R
-080A05A075R
-100A06A031R
-100A06A090R
Order Number
Set Bolt
VFX6-063A04A031R
-063A04A060R
-080A05A031R
-080A05A075R
-100A06A031R
-100A06A090R
HSC12045
HSC12070
HSC16040
HSC16080
HSC20040
HSC20090
Dimensions (mm)
D1
L1
D9
L7
D8
D7 W1
28
28
13 61
13 61
4 8 63
4 16 63
60 27
85 27
5 10 80
60 32
28
17 77.3 14.4 8.0 31 1.5
5 25 80 100 32
28
17 77.3 14.4 8.0 75 2.6
6 12 100 65 40
6 36 100 115 40
30
30
21 96.6 16.4 9.0 31 2.7

21 96.6 16.4 9.0 90 4.8
*2
Number of
Inserts
Seal
Coolant Anti-seizure
ap (kg) Clamp
Screw Washer Wrench Nozzle Lubricant
L8
Geometry
*1
Mass
Number of Teeth
Stock
R
Number of Effective Flute
y SHELL TYPE
Order Number
D9
D8
D1
L7
L8
12.4 7.0 31 0.9

12.4 7.0 60 1.3
XNMU1909
12R-MS
W12-S1
16
TS450 W16-S1 TKY20T
10
HSD
MK1KS
04004H08
25
12
W20-S1
36
145PSI
Standard
(145PSI - 725PSI)
725PSI
1015PSI
Nozzle Dia.
0.6mm
0.8mm
1.2mm
1.6mm
Order Number
HSD04004H06
HSD04004H08
HSD04004H12
HSD04004H16
INSERTS
Oder Number
L2
L3
S1
F1
Re
19.1 9.5 12.7 8.5
1.0
1.2
Geometry
F1
XNMU190912R-MS
L1
L3
Re
K076
L1
S1
Shape
Dimensions (mm)
L2
Stock
Coated
MP9030
MILLING

*12 The
0.8mm nozzles are installed in the standard. Select and use alternate nozzles from below list depend on the coolant pressure.
*

Work
Titanium Alloy (Ti-6Al-4V)
S Material
vc
n
Cutting Diameter Number of
(mm)
Effective Flute (SFM) (min-1)
&63
&80
&100
ae
(inch)
ap
(inch)
Titanium Alloy (Ti-5Al-5V-5Mo-3Cr)

fz
(inch/tooth)
Pc
(HP)
vc
n
Number of
Effective Flute (SFM) (min-1)
130
202
1.496<ae2.480 2.362
.004
18.0
165
253
.984<ae1.496 2.362
.004
12.7
195
303
.512<ae.984
2.362
.004
9.7
195
303
ae.512
2.362
.005
130
159
1.890<ae3.150 2.953
165
199
195
239
195
239
2.953
.005
130
127
2.362<ae3.937 3.543
.004
165
159
1.575<ae2.362 3.543
.004
28.0
195
191
.787<ae1.575 3.543
.004
21.5
195
191
.005
13.8
100
95
Cutting mode
ae
ap
ae
(inch)
ap
(inch)
fz
(inch/tooth)
Pc
(HP)
80
126
1.496<ae2.480 2.362
.003
9.4
80
126
.984<ae1.496 2.362
.003
5.4
100
152
.512<ae.984
2.362
.004
5.1
6.3
100
152
ae.512
2.362
.004
2.8
.004
27.9
80
99
1.890<ae3.150 2.953
.003
14.5
1.260<ae1.890 2.953
.004
19.7
80
99
1.260<ae1.890 2.953
.003
8.3
.630<ae1.260 2.953
.004
15.0
100
119
.630<ae1.260 2.953
.004
7.9
9.8
100
119
2.953
.004
4.4
39.7
80
80
2.362<ae3.937 3.543
.003
20.5
80
80
1.575<ae2.362 3.543
.003
11.8
100
95
.787<ae1.575 3.543
.004
11.3
.004
6.3
ae.630
ae.787
3.543
vc
n
fz
Pc
: Cutting speed
: Revolution
: Feed per tooth
: Estimated cutting power
ae.630
ae.787
3.543
Formula of max. metal removal rates
ap x ae x n x fz x Number of ute
MRR (inch3/min) =
1000
MILLING
(Note 1) Please note that machining performance differs according to conditions such as the rigidity of the machinery used, workpiece clamping rigidity, the coolant
supply system pressure and ow.
(Note 2) Internal coolant is recommended. For the tool holder, use an FMH arbor with a through coolant system. Use with external lubricating coolant is also effective.
K077
MILLING
DEEP SHOULDER
MILLING
LER
Light Alloy
Cast Iron
Roughing
y DESIGN FEATURES OF LER TYPE END MILL

Cutter Body
Insert : ZCMX Type
100corner
Flute B
Clamp Screw
Insert : CCMX Type
Flute A
a Different helical ute
a Additional body clearance
angles prevents chattering.
reduces probability of
chip jamming.
a Suitable for heavy cutting
Close Pitch Insert Position.
80corner
a All
4 cutting edges of CCMX insert are utilized,80

corners in ute "A" and 100 corners on ute "B".
Fig.2 Combination Shank
Fig.1
(Max. Depth of Cut)
(Max. Depth of Cut)
Dimensions (inch)
D1
L1
D4
ap
L2
RR
LER1606W20
6 1.000 4.281 1.250 2.000 1.063 8
2008W20
8 1.250 4.781 1.250 2.500 1.700 8 35
2012W20
2 12 1.250 5.531 1.250 3.250 2.480 8 35
2415W24
3 15 1.500 5.687 1.500 3.000 2.100 5 27
3218W32
3 18 2.000 6.750 2.000 3.500 2.500 5 52
Steel
Strong Cutting
Edge Type
: General Cutting
UTi20T
Order Number
Dimensions (inch)
Cermet Carbide
L1
L2
D1
S1
Re
CCMX083508ENA
09T308ENA
M
M
a a a

.313 .138 .031

.375 .156 .031
* CCMX09T308ENB
.375 .156 .031
ZCMX083508ERA
09T308ERA
M
M
* ZCMX09T308ERB
a a a
.409 .313
.472 .375

.137 .031
.156 .031
.472 .375
.156 .031
* These inserts are for slotting only when chipping occurs with standard inserts. Feed must be reduced 25%.
K078

: Unstable Cutting
Non-Ferrous Metal
Class
F7030
VP15TF
UP20M
MILLING
Bottom Insert (One Pocket Only) Peripheral and Bottom Inserts
Strong Cutting
Edge Type
Insert
Cast Iron
Coated
Shape
Wrench
CS300890T zTKY08F CCMX083508ENp 5

1
CS300890T xTKY08D ZCMX083508ERp 1
CS350990T zTKY10F CCMX09T308ENp 7
1
CS350990T xTKY10D ZCMX09T308ERp 1
1
1
2
Clamp Torque (lbf-in) : CS300890T=8.9, CS350990T=22
: Stable Cutting
Stainless Steel
NX2525
Work Material
Insert
x
Insert Screw
INSERTS
P
M
K
N
Type
(Fig.)
Teeth
Number of Teeth
Stock
Order Number
Number of Flute
Geometry

y SLOT MILLING
y SHOULDER MILLING
Cutting Condition Vs.Tool Diameter

Work Material Spindle Speed
& 1" & 1.25" & 1.5"
& 2"
Feed
P Mild Steel
(<160HB)
Cutting Condition Vs.Tool Diameter

Work Material Spindle Speed
& 1" & 1.25" & 1.5"
& 2"
Feed
min-1
2250
1800
1500
1100
P Mild Steel
inch/min
7 12
6 10
7 12
6 10
(<160HB)
2250
1800
1500
1100
-1
Carbon Steel min

(20HRC) inch/min
-1
min
Alloy Steel
(30HRC) inch/min
Insert
grade
-1
Stainless Steel min

(304)
inch/min
8 14
7 12
8 14
7 12
1750
1800
1200
900
6 10
58
6 10
58
1900
1500
1250
950
35
2.5 4
35
2.5 4
min-1
2250
inch/min 11 18
Insert
grade
1800
1500
1100
9 15
11 18
9 15
-1
2250
1800
1500
1100
Carbon Steel min
(20HRC) inch/min 12 21 11 18 12 21 11 18 VP15TF
VP15TF
Alloy Steel
(30HRC)
M
VP15TF
min-1
1750
1400
1200
900
inch/min
9 15
8 12
9 15
8 12
1900
1500
1250
950
7 12
6 10
7 12
6 10
-1
Stainless Steel min

(304)
inch/min
VP15TF
Warning : These feed rates are for ENA and ERA inserts.
Reduce feed 25% for ENB and ERB inserts.
Do not use ENB or ERB inserts in stainless steel, mild steel,
titanium alloys and nickel base alloys.
Insert breakage will occur.
y SHOULDER MILLING
.5xD1
(NOTE FEED RATE)
.25xD1
D1
CONDITION I
1.2xD1
CONDITION II
.2xD1
CONDITION I
GENERALLY DOWN (CLIMB) CUT IS RECOMMENDED
CONDITION II
(NOTE FEED RATE)
.5xD1
.25xD1
a Titanium alloy requires coolant (Cutting uid).

a Use higher recommended feed rate under CONDITION I.
a Use lower recommended feed rate under CONDITION II.
y NET CUTTING POWER
a Please use the chart below for reference, please select the
conditions that suits the machines power.

a Chip Discharge Q (inch3/min)=Table FeedDepth of CutCutting Width1000
a Titanium alloy requires coolant (Cutting uid).

a Use higher recommended feed rate under CONDITION I.
a Use lower recommended feed rate under CONDITION II.
y FOR USE OF LONG CUTTING LENGTH TYPE

a Since the overhang from the milling chuck is long, a large width of
cut will cause chattering and tool breakage.

a Keep the width of cut small and the depth of cut in axial direction large.
(See the following illustration.)

a For slot milling, keep the table feed at not more than half the value listed in
Large
)
HB
30
l2
e
Ste
Small
Net Cutting Power (HP)
the above table. (Use the standard cutting length type as much as possible.)
Metal Removal (Cubic inch)
MILLING
FORCED AIR IS REQUIRED AT CUTTING EDGE
1.2xD1
y SLOT MILLING
NG
Good
Large Depth of Cut

(.5xD1 .25xD1)
Small Depth of Cut

( < .25xD1)
SPARE PARTS
M001
TECHNICAL DATA
N001
K079
MILLING
MULTI FUNCTIONAL
MILLING
AQX
Light Alloy
Cast Iron
Including
Flat faces
Roughing
Fig.1
Number of
Teeth : 4
Fig.2
Fig.3

a The center bottom cutting edge
enables drilling and end milling

without prepared hole.
Long
Standard
Order Number
AQXUR124WA12S
164WA16S
204WA20S
244WA20S
AQXUR124SA12L
134SA12L
164SA16L
174SA16L
204SA20L
214SA20L
244SA20L
Stock
Type
y STANDARD EDGE TYPE
D1
L1
D4
L2
.750
1.000
1.250
1.500
.750
.797
1.000
1.047
1.250
1.297
1.500
4.125
4.875
5.250
5.625
7.250
7.250
8.500
8.500
9.000
9.000
9.500
.750
1.000
1.250
1.250
.750
.750
1.000
1.000
1.250
1.250
1.250
1.375
1.625
2.000
2.375
2.375
1.375
3.000
1.625
3.500
2.000
2.375
a
a
a
a
a
a
a
a
a
Type
(Fig.)
A3 *
R
a
a
Dimensions (inch)
1
.219
.281
.375
.438
.219
.219
.281
.281
.375
.375
.438
ap *
.750
1.000
1.250
1.500
.750
.750
1.000
1.000
1.250
1.250
1.500
3
2
2
2
1
1
1
1
1
1
1
Insert
Screw
TS25
TS32
TS407
TS5
TS25
TS25
TS32
TS32
TS407
TS407
TS5
Wrench
Insert
zTKY08F
xTKY08D
xTKY15D
xTKY25D
zTKY08F
zTKY08F
xTKY08D
xTKY08D
xTKY15D
xTKY15D
xTKY25D
QOG/MT0934R-pp
1443R-pp
1651R-pp
1959R-pp
QOG/MT0934R-pp
0934R-pp
1443R-pp
1443R-pp
1651R-pp
1651R-pp
1959R-pp
Clamp Torque (lbf-in) : TS25=8.9, TS32=8.9, TS407=31, TS5=66
Fig.4
Number of
Teeth:2
Order Number
AQXUR102WA10S
122WA12S
162WA16S
202WA20S
242WA20S
AQXUR102SA10L
112SA10L
122SA12L
132SA12L
162SA16L
172SA16L
202SA20L
212SA20L
242SA20L
3.5
Stock
Type
Long
Standard
MILLING
y SHORT EDGE TYPE
D1
L1
D4
L2
.625
.750
1.000
1.250
1.500
.625
.672
.750
.797
1.000
1.047
1.250
1.297
1.500
3.688
4.125
4.875
5.250
5.625
6.875
6.875
7.250
7.250
8.500
8.500
9.000
9.000
9.500
.625
.750
1.000
1.250
1.250
.625
.625
.750
.750
1.000
1.000
1.250
1.250
1.250
1.125
1.375
1.625
2.000
2.375
2.000
1.125
2.375
1.375
3.000
1.625
3.500
2.000
2.375
a
a
a
a
a
a
a
a
a
a
a
a
a
*3
Dimensions (inch)
Type
(Fig.)
A3 *
.188
.219
.281
.375
.438
.188
.188
.219
.219
.281
.281
.375
.375
.438
ap *
.281
.344
.469
.563
.688
.281
.281
.344
.344
.469
.469
.563
.563
.688
3
3
2
2
2
4
4
4
4
4
4
4
4
4
z
x
Insert
Screw
TS2A
TS25
TS32
TS407
TS55
TS2A
TS2A
TS25
TS25
TS32
TS32
TS407
TS407
TS55
Wrench
Insert
zTKY06F
zTKY08F
xTKY08D
xTKY15D
xTKY25D
zTKY06F
zTKY06F
zTKY08F
zTKY08F
xTKY08D
xTKY08D
xTKY15D
xTKY15D
xTKY25D
QOG/MT0830R-pp
0934R-pp
1443R-pp
1651R-pp
1959R-pp
QOG/MT0830R-pp
0830R-pp
0934R-pp
0934R-pp
1443R-pp
1443R-pp
1651R-pp
1651R-pp
1959R-pp
(Note) When exceeding A3 depth of cut, reduce feed rates by 50%(Do not exceed ap depth of cut). Reference page K085.
1 Dimension A3 represents the depth of cut when the cutting edge consists of 2 inserts.
2 ap: Maximum depth of cut.
3 Clamp Torque (lbf-in) : TS2A=5.3, TS25=8.9, TS33=8.9, TS407=31, TS5=66
*
*
K080 *a : Inventory maintained.
Number of Teeth : 4
METRIC Standard
Long
Standard
AQXR164SA16S
164SN16S
174SA16S
174SN16S
204SA20S
204SN20S
214SA20S
214SN20S
254SA25S
254SN25S
264SA25S
264SN25S
324SA32S
324SN32S
334SA32S
334SN32S
354SA32S
354SN32S
404SA32S
404SN32S
504SA42S
504SN42S
AQXR164SA16L
164SN16L
174SA16L
174SN16L
204SA20L
204SN20L
214SA20L
214SN20L
254SA25L
254SN25L
264SA25L
264SN25L
324SA32L
324SN32L
334SA32L
334SN32L
354SA32L
354SN32L
404SA32L
404SN32L
504SA42L
504SN42L
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s

u

u

u

u

u

u

u

u

u

u

u

u

u

u

u

u

u

u

u

u

u
Dimensions (mm)
*1
D1
L1
D4
L2
A3
16
16
17
17
20
20
21
21
25
25
26
26
32
32
33
33
35
35
40
40
50
50
16
16
17
17
20
20
21
21
25
25
26
26
32
32
33
33
35
35
40
40
50
50
120
120
120
120
130
130
130
130
140
140
140
140
150
150
150
150
150
150
160
160
170
170
175
175
175
175
185
185
185
185
220
220
220
220
230
230
230
230
230
230
240
240
250
250
16
16
16
16
20
20
20
20
25
25
25
25
32
32
32
32
32
32
32
32
42
42
16
16
16
16
20
20
20
20
25
25
25
25
32
32
32
32
32
32
32
32
42
42
30
30
30
30
35
35
35
35
40
40
40
40
50
50
50
50
50
50
60
60
70
70
50
50
30
30
60
60
35
35
75
75
40
40
90
90
50
50
50
50
60
60
70
70
4.5
4.5
4.5
4.5
6
6
6
6
7.5
7.5
7.5
7.5
9.5
9.5
9.5
9.5
11
11
12
12
15
15
4.5
4.5
4.5
4.5
6
6
6
6
7.5
7.5
7.5
7.5
9.5
9.5
9.5
9.5
11
11
12
12
15
15
ap *
17.6
17.6
17.6
17.6
22
22
22
22
27.5
27.5
27.5
27.5
35.2
35.2
35.2
35.2
40
40
44
44
55
55
17.6
17.6
17.6
17.6
22
22
22
22
27.5
27.5
27.5
27.5
35.2
35.2
35.2
35.2
40
40
44
44
55
55
A3 represents the depth of cut when the cutting edge consists of 2 inserts.
*12 Dimension
ap: Maximum depth of cut.
*3 Clamp Torque (lbf-in) : TS2A=5.3, TS25=8.9, TS33=8.9, TS407=31,
*
TS55=66, TS6S=89
Insert Screw
Wrench
TS2A
TS2A
TS2A
TS2A
TS25
TS25
TS25
TS25
TS33
TS33
TS33
TS33
TS407
TS407
TS407
TS407
TS407
TS407
TS55
TS55
TS6S
TS6S
TS2A
TS2A
TS2A
TS2A
TS25
TS25
TS25
TS25
TS33
TS33
TS33
TS33
TS407
TS407
TS407
TS407
TS407
TS407
TS55
TS55
TS6S
TS6S
zTKY06F
zTKY06F
zTKY06F
zTKY06F
zTKY08F
zTKY08F
zTKY08F
zTKY08F
zTKY08D
xTKY08D
xTKY08D
xTKY08D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY25D
xTKY25D
cTKY30T
cTKY30T
zTKY06F
zTKY06F
zTKY06F
zTKY06F
zTKY08F
zTKY08F
zTKY08F
zTKY08F
xTKY08D
xTKY08D
xTKY08D
xTKY08D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY25D
xTKY25D
cTKY30T
cTKY30T
Insert
QOG/MT0830R-G1/M2
QOG/MT1035R-G1/M2
QOG/MT1342R-G1/M2
QOG/MT1651R-G1/M2
QOG/MT1856R-G1/M2
QOG/MT2062R-G1/M2
QOG/MT2576R-G1/M2
QOG/MT0830R-G1/M2
QOG/MT1035R-G1/M2
MILLING
Stock
Order Number
Coolant Thru
Type
y STANDARD EDGE TYPE
QOG/MT1342R-G1/M2
QOG/MT1651R-G1/M2
QOG/MT1856R-G1/M2
QOG/MT2062R-G1/M2
QOG/MT2576R-G1/M2
INSERTS
K084
SPARE PARTS
M001
TECHNICAL DATA
N001
K081
MILLING
Number of Teeth : 2
METRIC Standard
Stock
Order Number
Long
MILLING
Standard
AQXR162SA16S
162SN16S
172SA16S
172SN16S
202SA20S
202SN20S
212SA20S
212SN20S
252SA25S
252SN25S
262SA25S
262SN25S
322SA32S
322SN32S
332SA32S
332SN32S
352SA32S
352SN32S
402SA32S
402SN32S
502SA42S
502SN42S
AQXR162SA16L
162SN16L
172SA16L
172SN16L
202SA20L
202SN20L
212SA20L
212SN20L
252SA25L
252SN25L
262SA25L
262SN25L
322SA32L
322SN32L
332SA32L
332SN32L
352SA32L
352SN32L
402SA32L
402SN32L
502SA42L
502SN42L
Coolant Thru
Type
y SHORT EDGE TYPE
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
s u
s
Dimensions (mm)
*1
D1
L1
D4
L2
A3
16
16
17
17
20
20
21
21
25
25
26
26
32
32
33
33
35
35
40
40
50
50
16
16
17
17
20
20
21
21
25
25
26
26
32
32
33
33
35
35
40
40
50
50
120
120
120
120
130
130
130
130
140
140
140
140
150
150
150
150
150
150
160
160
170
170
175
175
175
175
185
185
185
185
220
220
220
220
230
230
230
230
230
230
240
240
250
250
16
16
16
16
20
20
20
20
25
25
25
25
32
32
32
32
32
32
32
32
42
42
16
16
16
16
20
20
20
20
25
25
25
25
32
32
32
32
32
32
32
32
42
42
30
30
30
30
35
35
35
35
40
40
40
40
50
50
50
50
50
50
60
60
70
70
50
50
30
30
60
60
35
35
75
75
40
40
90
90
50
50
50
50
60
60
70
70
4.5
4.5
4.5
4.5
6
6
6
6
7.5
7.5
7.5
7.5
9.5
9.5
9.5
9.5
11
11
12
12
15
15
4.5
4.5
4.5
4.5
6
6
6
6
7.5
7.5
7.5
7.5
9.5
9.5
9.5
9.5
11
11
12
12
15
15
ap *
Insert Screw
Wrench
TS2A
TS2A
TS2A
TS2A
TS25
TS25
TS25
TS25
TS33
TS33
TS33
TS33
TS407
TS407
TS407
TS407
TS407
TS407
TS55
TS55
TS6S
TS6S
TS2A
TS2A
TS2A
TS2A
TS25
TS25
TS25
TS25
TS33
TS33
TS33
TS33
TS407
TS407
TS407
TS407
TS407
TS407
TS55
TS55
TS6S
TS6S
zTKY06F
zTKY06F
zTKY06F
zTKY06F
zTKY08F
zTKY08F
zTKY08F
zTKY08F
xTKY08D
xTKY08D
xTKY08D
xTKY08D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY25D
xTKY25D
cTKY30T
cTKY30T
zTKY06F
zTKY06F
zTKY06F
zTKY06F
zTKY08F
zTKY08F
zTKY08F
zTKY08F
xTKY08D
xTKY08D
xTKY08D
xTKY08D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY25D
xTKY25D
cTKY30T
cTKY30T
7.4
7.4
7.4
7.4
9.2
9.2
9.2
9.2
11.5
11.5
11.5
11.5
14.5
14.5
14.5
14.5
16
16
18
18
23
23
7.4
7.4
7.4
7.4
9.2
9.2
9.2
9.2
11.5
11.5
11.5
11.5
14.5
14.5
14.5
14.5
16
16
18
18
23
23
A3 represents the depth of cut when the cutting edge consists of 2 inserts.
*12 Dimension
ap: Maximum depth of cut.
*3 Clamp Torque (lbf-in) : TS2A=5.3, TS25=8.9, TS33=8.9, TS407=31, TS55=66, TS6S=89
*
K082
Insert
QOoT0830R-oo
QOoT1035R-oo
QOoT1342R-oo
QOoT1651R-oo
QOoT1856R-oo
QOoT2062R-oo
QOoT2576R-oo
QOoT0830R-oo
QOoT1035R-oo
QOoT1342R-oo
QOoT1651R-oo
QOoT1856R-oo
QOoT2062R-oo
QOoT2576R-oo
Section A-A
METRIC Standard
y SCREW-IN TYPE
Stock
R
Dimensions (mm)
D1
D4
D5
L1
L2
L11
H1
M*
A3*
ap* Insert Screw
Wrench
Insert
AQXR162M08A30
s u
16
8.5 14.7
48
30
10
M8
4.5
7.4
TS2A
zTKY06F
172M08A30
s u
17
8.5 14.5
48
30
10
M8
4.5
7.4
TS2A
zTKY06F
202M10A30
s u
20 10.5 18.6
49
30
14
M10
9.2
TS25
zTKY08F
212M10A30
s u
21 10.5 18.5
49
30
14
M10
9.2
TS25
zTKY08F
252M12A35
s u
25 12.5 23.5
57
35
19
M12
7.5 11.5
TS33
xTKY08D
262M12A35
s u
26 12.5 23.5
57
35
19
M12
7.5 11.5
TS33
xTKY08D
322M16A40
s u
32 17
28.5
63
40
24
M16
9.5 14.5
TS407
xTKY15D
332M16A40
s u
33 17
28.5
63
40
24
M16
9.5 14.5
TS407
xTKY15D
352M16A40
s u
35 17
28.5
63
40
24
M16 11
16
TS407
xTKY15D
QOoT1856R-oo
402M16A45
s u
40 17
28.5
68
45
24
M16 12
18
TS55
xTKY25D
QOoT2062R-oo
QOoT0830R-oo
QOoT1035R-oo
QOoT1342R-oo
QOoT1651R-oo
1 Dimension A3 represents the depth of cut when the cutting edge consists of 2 inserts.
2 ap: Maximum depth of cut.
3 Clamp Torque (lbf-in) : TS2A=5.3, TS25=8.9, TS33=8.9, TS407=31, TS55=66
MILLING
*
*
*
*
Coolant Thru
Order Number

3
SCREW-IN ARBORS
K142
INSERTS
K084
SPARE PARTS
M001
TECHNICAL DATA
N001
K083
MILLING
INSERTS
Work
Material
P
M
K
N
S
H
Steel
: Stable Cutting
Stainless Steel
Cast Iron
Hardened Materials
Order Number
End Mill Dia.
Class
Honing
VP15TF
VP30RT
M breaker
QOMT0830R-M2
& .625, .672
M E
0934R-M2
& .750, .797
M E
1443R-M2
& 1.000, 1.047
1651R-M2
& 1.250, 1.297

& 1.500
M E
& .625, .672
GF
1959R-M2
QOGT0830R-G1
Dimensions (inch)
L1
L2
S1
Re
a a
.350
.220
.120
.031
a a
.401
.264
.134
.031
M E
a a
.528
.350
.169
.031
M E
a a
.650
.433
.200
.031
.768
.512
.232
.031
.350
.220
.120
.016
a a
0934R-G1
& .750, .797
GF
.401
.264
.134
.016
1443R-G1
& 1.000, 1.047
GF
.528
.350
.169
.016
1651R-G1
& 1.250, 1.297
GF
.650
.433
.200
.016
1959R-G1
& 1.500
GF
.768
.512
.232
.016
*s
Geometry
Grade VP15TF has E honing.
INSERTS
P
M
K
N
S
H
For Metric Standard

Steel
: Stable Cutting
Stainless Steel

Hardened Materials
Class
Honing
VP15TF
VP30RT
End Mill
Dia.
Order Number
M breaker
QOMT0830R-M2
& 16,17 M E
1035R-M2
1342R-M2
1651R-M2
MILLING
Shape
Dimensions (mm)
Carbide
L1
L2
S1
Re
a a
8.4
5.5
0.8
& 20,21 M E
s s
10.6
3.5
0.8
& 25,26 M E
s s
13.1
8.7
4.2
0.8
& 32,33 M E
a a
16.5
11
5.1
0.8
1856R-M2
& 35
M E
s s
18
12
5.6
0.8
2062R-M2
& 40
M E
s s
20.4
13.6
6.2
0.8
2576R-M2
& 50
M E
s s
25.8
17.2
7.6
0.8
8.4
5.5
0.4
1035R-G1
& 20,21 G F
10.6
3.5
0.4
1342R-G1
& 25,26
13.1
8.7
4.2
0.4
1651R-G1
& 32,33
1856R-G1
& 35
2062R-G1
& 40
2576R-G1
& 50
*
*s
G F* s
G F* s
G F* s
G F* s
G F* s
QOGT0830R-G1
& 16,17 G F
* Grade VP15TF has E honing.

: Unstable Cutting
Honing :
E : Round F : Sharp
Non-Ferrous Metal
Coated
G breaker
: General Cutting
Cast Iron
HTi10
Work
Material
K084
HTi10
Shape
: Unstable Cutting
Honing :
E : Round F : Sharp
Non-Ferrous Metal
Coated Carbide
G breaker
: General Cutting
16.5
11
5.1
0.4
18
12
5.6
0.4
20.4
13.6
6.2
0.4
25.8
17.2
7.6
0.4
Geometry

a A3 is the depth of cut for the full dual blade
portion at the end of the cutting edge.

occurs, there is an area where the cutting
edge becomes single bladed, not forming
full dual blade conguration. As such,
please pay special attention to the
relationship between depth of cut and feed.
a In general, the edge at the border of cut
tends to suffer from damages. At large
depth of cut operations, applying the
following depth of cut (t), at which the edge
is full dual bladed at the border of cut, is
recommended to prevent damage to the
cutting edge.
(Note) Figures for A3 and ap are shown

in the table of holder standard.
Tool diameter Recommended depth of cut t (inch)

& .625, & .672
.472 .551
& .750, & .797
.551 .669
& 1.000, & 1.047
.669 .866
& 1.250, & 1.297
.866 1.102
& 1.500
1.102 1.378
Overhang
a Beyond the range of A3 where overlapping
(Note) D1=Cutting Edge

Diameter
Feed Rate
a Chatter vibration and other problems tend to occur
at operations where overhang length is large

and/or machine rigidity is low, resulting in unstable
machining.
a Please reduce feed accordingly, using the above
chart as a guideline.

Work Material Hardness Grade
P
Mild Steel
< 180HB
& .625", & .672"

& .750", & .797" & 1.000", & 1.047" & 1.250", & 1.297"
& 1.500"
Cutting (& 16mm, &17mm) (& 20mm, &21mm) (& 25mm, &26mm) (& 32mm, &33mm)
(& 40mm)
Speed
(SFM) Depth of Cut Width of Cut Feed Depth of Cut Width of Cut Feed Depth of Cut Width of Cut Feed Depth of Cut Width of Cut Feed Depth of Cut Width of Cut Feed
(inch) (inch) (inch/rev) (inch) (inch) (inch/rev) (inch) (inch) (inch/rev) (inch) (inch) (inch/rev) (inch) (inch) (inch/rev)
.177 .315 .010

590
VP15TF ( ) .177 .472 .197 .006
490 720
.472 .669 .118 .004
.177 .315 .008
.236 .394 .012
.472 .787
.020
.236 .551 .276 .010 .295 .669 .315 .011 .374 .866 .433 .013 .472 1.102 .512
.016
.551 .866 .157 .007 .669 1.063 .197 .008 .866 1.378 .236 .010 1.102 1.732 .276
.012
.236 .394 .010
.295 .492 .014
.295 .492 .012
.374 .630 .016
.374 .630 .014
.472 .787
.016
525
Carbon Steel
180350HB VP15TF ( ) .177 .472 .157 .006 .236 .551 .236 .008 .295 .669 .276 .010 .374 .866 .394 .011 .472 1.102 .472 .013
395 655
Alloy Steel
.177 .315 .008
Stainless Steel
< 270HB
490
VP30RT ( ) .177 .472 .157 .006
395 590
.472 .669 .079 .003
.177 .315 .010
Cast Iron
.118 .006 .669 1.063 .157 .007 .866 1.378 .197 .008 1.102 1.732 .236
.236 .394 .010
.010
.374 .630 .014
.472 .787
.016
.236 .551 .236 .008 .295 .669 .276 .010 .374 .866 .394 .011
.472 1.102 .472
.013
.118 .006 .669 1.063 .157 .007 .866 1.378 .197 .008 1.102 1.732 .236
.010
.551 .866
.236 .394 .012
.295 .492 .012
.295 .492 .014
.374 .630 .016
.472 .787
.020
590
Tensile Strength
VP15TF ( ) .177 .472 .197 .006 .236 .551 .276 .010 .295 .669 .315 .011 .374 .866 .433 .013 .472 1.102 .512 .016
490 720
< 450MPa
.472 .669
Aluminum Alloy
.551 .866
.118 .004
.551 .866 .157 .007 .669 1.063 .197 .008 .866 1.378 .236 .010 1.102 1.732 .276
.177 .433 .012

HTi10
1640
.472 .315 .008
.177
(G1 Breaker) (655 2620)
.472 .669 .197 .006
.236 .551 .394 .012 .295 .669 .492 .013 .374 .866 .630 .015 .472 1.102 .787
.018
.551 .866 .236 .009 .669 1.063 .295 .010 .866 1.378 .394 .012 1.102 1.732 .472
.014
.177 .197 .006
.236 .551 .014
.236 .236 .008
.295 .689 .016
.295 .276 .009
.374 .906 .018
.374 .315 .010
.012
.472 1.102 .022
.472 .394
MILLING
.472 .669 .079 .003
.012
260
Hardened Steel 4555HRC VP15TF ( ) .177 .472 .118 .004 .236 .551 .157 .006 .295 .669 .157 .007 .374 .866 .197 .008 .472 1.102 .236 .009
160 390
.472 .669 .039 .002
.551 .866 .079 .005 .669 1.063 .079 .006 .866 1.378 .079 .006 1.102 1.732 .079
.007
(Note 1) Please pay special attention on the depth of cut when using the short edge type.
(Note 2) When using the G1 breaker (VP15TF), please reduce the feed rate by 20%.
SPARE PARTS
M001
TECHNICAL DATA
N001
K085
MILLING
y CUTTING CONDITIONS FOR SLOTTING
Work Material
& .625", & .672" & .750", & .797" &1.000", &1.047" &1.250", &1.297"
& 1.500"
(& 40mm)
Cutting Speed (&16mm, &17mm) (&20mm, &21mm) (&25mm, &26mm) (&32mm, &33mm)
(SFM)
Depth of Cut Feed Depth of Cut Feed Depth of Cut Feed Depth of Cut Feed Depth of Cut Feed
(inch)
(inch/rev)
(inch)
(inch/rev)
(inch)
(inch/rev)
(inch)
(inch/rev)
(inch)
(inch/rev)
Hardness
Grade
< 180HB
VP15TF
P
Mild Steel
Carbon Steel
180 350HB
Alloy Steel
VP15TF
Stainless Steel
VP30RT
K
Cast Iron
< 270HB
Tensile Strength
< 450MPa
N
Aluminum Alloy
H Hardened Steel 45 55HRC
.177
590
.472
.177
(490 720)
.472 .669
.177
525
.472
.177
(395 655)
.472 .669
.177
490
.472
.177
(395 590)
.472 .669
.177
590
.472
.177
(490 720)
.472 .669
.177
HTi10
1640
.472
.177
(G1 Breaker) (655 2620)
.472 .669
VP15TF
VP15TF
.236 .007
.295
.006
.004 .236 .551 .006 .295 .669
.003 .551 .866 .004 .669 1.063
.236 .006
.295
.006
.472
.374 .010
.008
.006 .374 .866 .008 .472 1.102
.005 .866 1.378 .006 1.102 1.732
.374 .008
.472
.007
.012
.010
.004 .236 .551

.002 .551 .866
.236
.006
.004 .236 .551
.002 .551 .866
.005 .295 .669

.004 .669 1.063
.295
.006
.005 .295 .669
.004 .669 1.063
.006 .374 .866

.004 .866 1.378
.374
.007
.006 .374 .866
.004 .866 1.378
.006 .472 1.102

.005 1.102 1.732
.472
.008
.006 .472 1.102
.005 1.102 1.732
.008
.006
.236
.006
.004 .236 .551
.003 .551 .866
.236
.007
.005 .236 .551
.004 .551 .866
.295
.007
.006 .295 .669
.004 .669 1.063
.295
.008
.006 .295 .669
.005 .669 1.063
.374
.008
.006 .374 .866
.005 .866 1.378
.374
.009
.007 .374 .866
.006 .866 1.378
.472
.010
.008 .472 1.102
.006 1.102 1.732
.472
.011
.009 .472 1.102
.006 1.102 1.732
.012
.010
.007
.177 .004
.236 .005
.295 .006
.374 .006
260
(160 390) .177 .472 .003 .236 .551 .004 .295 .669 .005 .374 .866 .005
.007
.010
.010
.008
.006
.013
.011
.008
.472 .007
.472 1.102 .006
(Note 1) Please pay special attention on the depth of cut when using the short edge type.

y CUTTING CONDITIONS (For Ramping)
a When machining steel the recommended ramping angle is 3. If a ramping angle larger
than 3 is used, then the chips may not be broken effectively resulting in chips wrapping
around the tool.
a When ramping, it is recommended to reduce the feed rate by 40%.
y CUTTING CONDITIONS (For Drilling and Plunging)

a Drilling
a Plunge Milling
a The recommended drilling depth is
MILLING
less than .5D1.

a Use step feed when drilling (.01 .02
inch) to ensure that the chips are
effectively broken.
a Use internal or external cooling to
ensure that the chips disposal is
sufciently achieved.
a The chips generated can discharge
in any direction, so ensure that
adequate safety precautions are
taken.
Work Material
Hardness
Grade
Mild Steel
< 180HB
VP15TF
Carbon Steel
Alloy Steel
180 350HB
Stainless Steel
same as the feed for drilling.

a No step feed necessary.
a Please refer to the following
table for the depth of cut at

plunging operations.
Depth of Cut in the Radius Direction
Peck Feed
Peck Feed
& .625", & .672"

Cutting Speed (&16mm, &17mm)
(SFM)
Feed
Step
(inch/rev) (inch)
&.750", &.797" &1.000", &1.047" &1.250", &1.297"

(&20mm, &21mm) (&25mm, &26mm) (&32mm, &33mm)
<
<
.4D1
.5D1
& 1.500"
(& 40mm)
Feed Step Feed Step Feed Step Feed Step

(inch/rev) (inch) (inch/rev) (inch) (inch/rev) (inch) (inch/rev) (inch)
.001.003
.008
.002
.012
.002
.012
.002
.012
.002
.012
VP15TF
590
(490 720)
525
(395 655)
.001 .003
.008
.002
.012
.002
.012
.002
.012
.002
.012
< 270HB
VP30RT
490
(395 590)
.001 .003
.006
.002
.010
.002
.010
.002
.010
.002
.010
Cast Iron
Tensile Strength
< 450MPa
VP15TF
590
(490 720)
.002 .004
.016
.002
.020
.002
.020
.003
.020
.003
.020
Aluminum Alloy
1640
HTi10
(G1 Breaker) (655 2620) .002 .004
.008
.002
.012
.002
.012
.003
.012
.003
.012
Hardened Steel
45 55HRC
.006
.001
.010
.001
.010
.002
.010
.002
.010
VP15TF
260
(160 390)
.001 .003
(Note 1) Helical grooving is strongly recommended for machining of tempered steel.

K086
a The feed for plunging is the
Depth of cut in
the radius direction

y CUTTING CONDITIONS (Helical Cutting)
a How to calculate the theoretical
center of the tool path.
dc = DH - D1
Theoretical center of the tool Desired hole diameter Cutting edge diameter
P = ) dc tan %
a Depth of cut for a pass.
(Note) % < 3
a Min. machined hole diameter at helical cutting : 1.2D1
Max. machined hole diameter at helical cutting : 1.8D1
a For chip discharge, please always apply air blow.
(When aluminum cutting, please use coolant.)
a When helical cutting, it is recommended to reduce the feed rate by 40%.

a When using the G1 breaker (VP15TF), please reduce the feed rate by 20%.
Hardness
Grade
590
VP15TF (
490 720)
< 180HB
Mild Steel
525
Carbon Steel
180 350HB VP15TF (
395 655)
Alloy Steel
M
Stainless Steel
K
Cast Iron
490
VP30RT (
395 590)
< 270HB
590
Tensile Strength
VP15TF (
< 450MPa
490 720)
N
Aluminum Alloy
HTi10
1640
(G1 Breaker) (655 2620)
260
Hardened Steel 45 55HRC VP15TF (160 390)
Work Material
Hardness
Grade
< 180HB
VP15TF
P
Mild Steel
.787
.315
.006
.017
.945
.394
.007
.017
1.181
.492
.008
.022
.984
.472
.006
.039
1.181
.591
.006
.043
1.496
.748
.007
.056
1.142
.630
.005
.056
1.417
.787
.006
.069
1.772
.984
.006
.087
.787
.315
.006
.013
.945
.394
.006
.013
1.181
.492
.007
.016
.984
.472
.005
.029
1.181
.591
.006
.032
1.496
.748
.006
.042
1.142
.630
.004
.042
1.417
.787
.005
.052
1.772
.984
.006
.065
.787
.118
.006
.009
.945
.157
.006
.009
1.181
.197
.007
.011
.984
.197
.005
.019
1.181
.276
.006
.022
1.496
.354
.006
.028
1.142
.315
.004
.028
1.417
.394
.005
.035
1.772
.492
.006
.043
.787
.394
.006
.022
.945
.551
.007
.022
1.181
.709
.008
.027
.984
.512
.006
.048
1.181
.669
.006
.054
1.496
.827
.007
.070
1.142
.630
.005
.070
1.417
.787
.006
.086
1.772
.984
.006
.108
.787
.394
.007
.017
.945
.551
.008
.017
1.181
.709
.009
.022
.984
.512
.006
.039
1.181
.669
.007
.043
1.496
.827
.008
.056
1.142
.630
.006
.056
1.417
.787
.006
.069
1.772
.984
.007
.087
.787
.118
.004
.009
.945
.157
.005
.009
1.181
.197
.006
.011
.984
.197
.003
.019
1.181
.276
.004
.022
1.496
.354
.005
.028
1.142
.315
.002
.028
1.417
.394
.003
.035
1.772
.492
.004
.043
& 1.250", & 1.297"

& 1.500"
(& 40mm)
(& 32mm, & 33mm)
Cutting Speed
Machining Max. Depth Feed DOC/pass Machining Max. Depth Feed DOC/pass
(SFM)
Diameter
of Cut
Diameter
of Cut
(inch)
(inch) (inch/rev) (inch/pass) (inch)
(inch) (inch/rev) (inch/pass)
590
(490 720)
1.496
1.890
.630
.945
.010
.009
.026
.069
1.890
2.362
.787
1.181
.012
.010
.035
.086
2.283
1.260
.008
.112
2.835
1.575
.009
.138
1.496
.630
.008
.019
1.890
.787
.010
.026
1.890
2.283
.945
1.260
.007
.006
.052
.084
2.362
2.835
1.181
1.575
.009
.008
.065
.104
Carbon Steel
Alloy Steel
180 350HB
VP15TF
525
(395 655)
Stainless Steel
< 270HB
VP30RT
490
(395 590)
1.496
1.890
2.283
.236
.433
.630
.008
.007
.006
.013
.035
.056
1.890
2.362
2.835
.315
.551
.787
.010
.009
.008
.017
.043
.069
Cast Iron
Tensile Strength
< 450MPa
VP15TF
590
(490 720)
1.496
1.890
2.283
.866
1.063
1.260
.010
.009
.008
.032
.086
.141
1.890
2.362
2.835
1.102
1.339
1.575
.012
.010
.009
.043
.108
.173
Aluminum Alloy
HTi10
1640
(G1 Breaker) (655 2620)
1.496
1.890
2.283
.866
1.063
1.260
.011
.009
.009
.026
.069
.112
1.890
2.362
2.835
1.102
1.339
1.575
.013
.011
.009
.035
.086
.138
260
(160 390)
1.496
1.890
2.283
.236
.433
.630
.006
.006
.005
.013
.035
.056
1.890
2.362
2.835
.315
.551
.787
.007
.006
.006
.017
.043
.069
H
Hardened Steel 45 55HRC
VP15TF
MILLING
Work Material
& 1.000", & 1.047"

& .625", & .672"
& .750", & .797"
(& 16mm, & 17mm)
(& 20mm, & 21mm)
(& 25mm, & 26mm)
Cutting Speed
(SFM) Machining Max. Depth Feed DOC/pass Machining Max. Depth Feed DOC/pass Machining Max. Depth Feed DOC/pass
Diameter of Cut
Diameter of Cut
Diameter of Cut (inch/rev)
(inch/pass)
(inch) (inch) (inch/rev) (inch/pass) (inch) (inch) (inch/rev) (inch/pass) (inch) (inch)
K087
MILLING
MULTI FUNCTIONAL
MILLING
AJX
Light Alloy
Cast Iron
Including
Flat faces
Roughing
Fig.1 FA at shank

(Corresponding Inclination Angle)

(Max. Depth of Cut)
a 13,15 positive insert.

a High rigidity due to double clamp
Fig.2
structure.
a Suitable for high feed cutting.
a Special insert design with the use of
(Max. Depth of Cut)
3 cutting edges.
Fig.3
Fig.4
(Max. Depth of Cut)
(Max. Depth of Cut)
Standard
L1
L2
ap
A2
B 2
z
x
Insert Clamp Clamp Bridge Spring

Screw Bridge
Screw
D1
D4
.625
.625 .346 3.750 1.250 .039 .012 2.12 1 TS25
1 TS25
Wrench
Insert
zTKY08F JOMp06T215
ZZSR-pp
zTKY08F
06R112FA10S
.688
.625 .409 3.750
.750
.750 .417 4.750 2.000 .059 .020 1.31 2 TS33
.875
.750 .535 4.750 1.250 .059 .020
2 1.000 1.000 .602 5.625 2.375 .079 .039 1.1 3 TS351 AMS3 AJS3010T10 ASS2 xTKY10D JDMp09T320
ZDSR-pp
2 1.125 1.000 .728 5.625 1.625 .079 .039 1 TS351 AMS3 AJS3010T10 ASS2 xTKY10D
08R142FA12S
AJXU09R162WA16S
09R182FA16S
Long
D6
AJXU06R102FA10S
AJXU08R122WA12S
MILLING
Dimensions (inch)
Type (Fig.)
Order Number
Stock
Number of Teeth
Type
y SHANK TYPE
.750 .039 .012
1 TS33
xTKY08D JOMp080320
ZZSR-pp
xTKY08D
AJXU12R202WA20S
12R243WA20S
2 1.250 1.250 .789 6.000 2.750 .079 .059 0.94 3 TS43 AMS4 AJS4012T15 ASS2 xTKY15D JDMp120420
ZDSR-pp
3 1.500 1.250 1.038 6.000 2.000 .079 .059 3 TS43 AMS4 AJS4012T15 ASS2 xTKY15D
AJXU14R323WA24S
3 2.000 1.500 1.534 6.000 2.000 .079 .079
AJXU06R102SA10M
06R102SA10L
06R112SA10L
06R123SA12M
AJXU08R122SA12L
p140520
3 TS54 AMS5 AJS5014T25 ASS3 xTKY25D JDM
ZDSR-pp
.625
.625 .346 5.750 1.500 .039 .012 1.75 4 TS25
zTKY08F
.625
.625 .346 5.750 2.750 .039 .012 0.93 4 TS25
.688
.625 .409 5.750
4 TS25
zTKY08F JOMp06T215
ZZSR-pp
zTKY08F
.750
.750 .472 7.000 2.375 .039 .012 1.11 4 TS25
zTKY08F
.750
.750 .417 7.000 4.000 .059 .020 0.64 4 TS33
xTKY08D
08R142SA12L
.875
.750 .535 7.000 1.250 .059 .020
4 TS33
xTKY08D
08R163SA16M
3 1.000 1.000 .661 8.000 2.750 .059 .020 0.94 4 TS33
xTKY08D
AJXU09R162SA16L
2 1.000 1.000 .602 8.000 4.750 .079 .039 0.54 4 TS351 AMS3 AJS3010T10 ASS2 xTKY10D
09R182SA16L
2 1.125 1.000 .728 8.000 1.625 .079 .039
09R203SA20M
4 TS351 AMS3 AJS3010T10 ASS2 xTKY10D JDMp09T320

ZDSR-pp
09R244SA20M
4 1.500 1.250 1.114 10.000 2.375 .079 .039
AJXU12R202SA20L
12R243SA20L
3 1.500 1.250 1.038 10.000 2.000 .079 .059
12R243SA24L
3 1.500 1.500 1.038 10.000 2.750 .079 .059 0.94 4 TS43 AMS4 AJS4012T15 ASS2 xTKY15D
.750 .039 .012
JOMp080320
ZZSR-pp
4 TS351 AMS3 AJS3010T10 ASS2 xTKY10D
4 TS43 AMS4 AJS4012T15 ASS2 xTKY15D
JDMp120420
ZDSR-pp
* Clamp Torque (lbf-in) : TS25=8.9, TS33=8.9, TS351=22, TS43=31, TS54=66, AJS3010T10=22, AJS4012T15=31, AJS5014T25=66
K088
.079"(Max. Depth of Cut)
.079" (Max. Depth of Cut)
Order Number
Stock
Number of Teeth
Type
y ARBOR TYPE
Coarse Pitch
D1
D6
L1
D9
L7
D8 D12 W1
Insert Clamp Clamp Bridge Spring Wrench Coolant thru

L8 D11 A2 Screw
Bridge Screw
Set Bolt
Insert
HSCU JDMp120420
3 2.000 1.539 2.000 .750 .748 .415 1.875 .313 .187 .600 .059 TS43 AMS4 AJS40
12T15 ASS2 zTKY15T 37513H
ZDSR-pp
14R2503C
3 2.500 2.032 2.000 1.000 1.024 .539 2.375 .375 .219 .787 .079
14R0304C
4 3.000 2.532 2.000 1.000 1.024 .539 2.750 .375 .219 .787 .079
14R0405E
HSCU
50014H
AJX14RA12505E
HSCU
5 4.000 3.531 2.500 1.500 1.181 .787 3.750 .625 .375 1.181 .079 TS54 AMS5 AJS50
MBAU
5 4.921 4.457 2.480 1.500 1.575 2.205 3.937 .625 .375 .079
75016H
14RA16006F
6 6.299 5.835 2.480 2.000 1.693 2.835 3.937 .750 .437
.079
14R2504C
14R0305C
5 3.000 2.532 2.000 1.000 1.024 .539 2.750 .375 .219 .787 .079
14R0406E
HSCU
6 4.000 3.531 2.500 1.500 1.181 .787 3.750 .625 .375 1.181 .079 TS54 AMS5 AJS50
AJX14RA12507E
7 4.921 4.457 2.480 1.500 1.575 2.205 3.937 .625 .375
.079
14RA16008F
8 6.299 5.835 2.480 2.000 1.693 2.835 3.937 .750 .437
.079
5 2.000 1.606 2.000 .750 .748 .415 1.875 .313 .187 .600 .039 TS351 AMS3 AJS3010
T10
12R2505C
5 2.500 2.039 2.000 1.000 1.024 .539 2.375 .375 .219 .787 .059
12R0306C
12R0407E
AJXU09R0205
JDMp
140520
ZDSR-pp
MBAU
100016H
HSCU JDMp120420
ASS2 zTKY15T 37513H
ZDSR-pp
4 2.000 1.539 2.000 .750 .748 .415 1.875 .313 .187 .600 .059 TS43 AMS4 AJS40
12T15
4 2.500 2.032 2.000 1.000 1.024 .539 2.375 .375 .219 .787 .079
AJXU12R0204
Fine Pitch
Dimensions (inch)
AJXU12R0203
Extra Fine Pitch
AJX12
AJX14
A.R :+8
A.R :+8
R.R :-5 -4 R.R :-3
HSCU
50014H
JDMp
140520
ZDSR-pp
MBAU
75016H
MBAU
100016H
HSCU JDMp09T320
xTKY10D 37513H
ZDpR-pp
HSCU
ASS2
50014H
zTKY15T
6 3.000 2.543 2.000 1.000 1.024 .539 2.750 .375 .219 .787 .059 TS43 AMS4 AJS4012
T15
HSCU
75016H
7 4.000 3.539 2.500 1.500 1.181 .787 3.750 .625 .375 1.181 .059
MILLING
AJX09
A.R :+8
R.R :-6
JDMp
120420
ZDSR-pp
* Clamp Torque (lbf-in) : TS351=22, TS43=31, TS54=66, AJS3010T10=22, AJS4012T15=31, AJS5014T25=66
INSERTS
K095
SPARE PARTS
M001
TECHNICAL DATA
N001
K089
MILLING
(Max. Depth of Cut)

METRIC Standard
Stock
Order Number
MILLING
Standard
Short
AJX06R162SA16SS
172SA16SS
AJX06R162SA16S
172SA16S
203SA20S
223SA20S
AJX08R202SA20S
222SA20S
253SA25S
283SA25S
AJX09R252SA25S
282SA25S
303SA32S
323SA32S
353SA32S
404SA32S
404SA42S
AJX12R302SA32S
322SA32S
352SA32S
403SA32S
403SA42S
AJX14R503SA42S
634SA42S
s
s
s
s
s
s
s
s
s
s
Number of Teeth
Type
y SHANK TYPE
D1 D 4
L2
ap
A2
B 2
Insert Clamp Clamp Bridge Spring Wrench

Screw Bridge
Screw
L1
2 16 16
2 17 16
8.9
9.9
70 20 1.0 0.3 330

TS25
TS25
70 20 1.0 0.3

zTKY08F JOMp06T215
zTKY08F ZZSR-pp
2 16 16
2 17 16
8.9 110 30 1.0 0.3 215

TS25
TS25
9.9 110 20 1.0 0.3

zTKY08F
3 20 20 12.9 130 50 1.0 0.3 118

TS25
TS25
3 22 20 14.9 130 30 1.0 0.3

zTKY08F
2 20 20 11.4 130 50 1.5 0.5 118

TS33
TS33
2 22 20 13.4 130 30 1.5 0.5

xTKY08D
3 25 25 16.4 140 60 1.5 0.5 106

TS33
TS33
3 28 25 19.4 140 40 1.5 0.5

xTKY08D
zTKY08F
xTKY08D
3 30 32 20.0 150 70 2.0 1.0 148

TS351 AMS3 AJS3010T10 ASS2 xTKY10D
3 32 32 21.9 150 70 2.0 1.0 056

3 35 32 24.9 150 50 2.0 1.0
4 40 32 29.9 150 50 2.0 1.0
4 40 42 29.9 150 70 2.0 1.0 148

2 30 32 18.3 150 70 2.0 1.5 148

TS407 AMS4 AJS4012T15
2 32 32 20.3 150 70 2.0 1.5 1
2 35 32 23.3 150 50 2.0 1.5
3 40 32 28.3 150 50 2.0 1.5
s
s
s
s
s
s
3 40 42 28.3 150 70 2.0 1.5 148

TS43
TS54
3 50 42 38.2 150 50 2.0 2.0
TS54
4 63 42 51.1 150 50 2.0 2.0
JOMp
080320
ZZSR-pp
xTKY08D
JOMp
06T215
ZZSR-pp
zTKY08F
2 25 25 14.9 140 60 2.0 1.0 106

2 28 25 17.9 140 40 2.0 1.0
Insert
D6
* Clamp Torque (lbf-in) : TS25=8.9, TS33=8.9, TS351=22, TS407=31, TS43=31, TS54=66
K090
Dimensions (mm)
JDMp
09T320
ZDSR-pp
ASS2 xTKY15D
ASS2 xTKY15D
ASS2 xTKY15D
ASS2 xTKY15D
JDMp
120420
ZDSR-pp
AMS4 AJS4012T15 ASS2 xTKY15D

AMS5 AJS5014T25 ASS3 xTKY25D JDMp140520
AMS5 AJS5014T25 ASS3 xTKY25D ZDSR-pp
AJX06R162SA16L
172SA16L
203SA20L
223SA20L
AJX08R202SA20L
222SA20L
253SA25L
283SA25L
AJX09R252SA25L
282SA25L
303SA32L
323SA32L
353SA32L
404SA32L
404SA42L
AJX12R302SA32L
322SA32L
352SA32L
403SA32L
403SA42L
AJX14R503SA42L
634SA42L
AJX06R162SA16EL
172SA16EL
AJX08R202SA20EL
222SA20EL
AJX09R252SA25EL
282SA25EL
AJX12R302SA32EL
322SA32EL
352SA32EL
402SA32EL
402SA42EL
Stock
s
s
s
s
s
s
s
s
D 1 D4
D6
L1
L2
ap
A2
B2

Screw Bridge
Screw
70 1.0 0.3 056

TS25
TS25
20 1.0 0.3

zTKY08F
3 20 20 12.9 180 100 1.0 0.3 038

TS25
TS25
3 22 20 14.9 180 30 1.0 0.3

zTKY08F
2 20 20 11.4 180 100 1.5 0.5 036

TS33
TS33
2 22 20 13.4 180 30 1.5 0.5

xTKY08D
3 25 25 16.4 200 120 1.5 0.5 032

TS33
TS33
3 28 25 19.4 200 40 1.5 0.5

xTKY08D
2 16 16
2 17 16
8.9 150
9.9 150
zTKY08F
Insert
JOMp
06T215
ZZSR-pp
zTKY08F
xTKY08D
JOMp
080320
ZZSR-pp
xTKY08D
s 2 25 25 14.9 200 120 2.0 1.0 030

s
s

40 2.0 1.0
3 30 32 20.0 200 120 2.0 1.0 102
2 28 25 17.9 200
3 32 32 21.9 200 120 2.0 1.0 032

3 35 32 24.9 200 50 2.0 1.0
4 40 32 29.9 250 50 2.0 1.0
4 40 42 29.9 250
s
s
70 2.0 1.0 148

2 30 32 18.3 200 120 2.0 1.5 1
2 32 32 20.3 200 120 2.0 1.5 036
2 35 32 23.3 200 50 2.0 1.5
3 40 32 28.3 250 50 2.0 1.5
3 40 42 28.3 250
3 50 42 38.1 250
4 63 42 51.1 250
s
s
s
s
s
s
s
s
s
s
70 2.0 1.5 148

TS43
TS54
TS54
50 2.0 2.0
50 2.0 2.0
ASS2 xTKY15D
ASS2 xTKY15D
ASS2 xTKY15D
JDMp
120420
ZDSR-pp
8.9 200 100 1.0 0.3 038

TS25
TS25
9.9 200 20 1.0 0.3

zTKY08F JOMp06T215
xTKY08F ZZSR-pp
2 20 20 11.4 250 130 1.5 0.5 030

TS33
TS33
2 22 20 13.4 250 30 1.5 0.5

xTKY08D JOMp080320
xTKY10D ZZSR-pp
2 16 16
2 17 16
2 25 25 14.9 300 180 2.0 1.0 018

TS351 AMS3 AJS3010T10 ASS2 xTKY10D JDMp09T320
TS351 AMS3 AJS3010T10 ASS2 xTKY15D ZDSR-pp
2 28 25 17.9 300 40 2.0 1.0
2 40 42 28.3 350
ASS2 xTKY15D
AMS5 AJS5014T25 ASS3 xTKY25D JDMp140520

AMS5 AJS5014T25 ASS3 xTKY25D ZDSR-pp
ASS2 xTKY10D
2 30 32 18.3 300 180 2.0 1.5 042

2 32 32 20.3 300 180 2.0 1.5 024
2 35 32 23.3 300 50 2.0 1.5
2 40 32 28.3 350 50 2.0 1.5
JDMp
09T320
ZDSR-pp
70 2.0 1.5 148

TS43
ASS2 xTKY15D
ASS2 xTKY15D
ASS2 xTKY15D
ASS2 xTKY15D
JDMp
120420
ZDSR-pp
* Clamp Torque (lbf-in) : TS25=8.9, TS33=8.9, TS351=22, TS407=31, TS43=31, TS54=66
INSERTS
K095
SPARE PARTS
M001
TECHNICAL DATA
N001
MILLING
Extra Long
Long
Number of Teeth
Type
Order Number
Dimensions (mm)
K091
50
63
80
100
MILLING
125
160
METRIC Standard
For metric arbors
AJX09
A.R :+8
R.R :-6
50 38.3 50 22 20 11
AJX14-063A03R
63 51.1 50 22 20 11
-080A04R
80 68.1 50 27 23 13
-100A05R
5 100 88.1 63 32 26 17
-125B05R
5 125 113.2 63 40 40 56
-160B06R
6 160 148.2 63 40 40 56
AJX09-050A05R
50 40
AJX12-050A04R
50 38.3 50 22 20 11
-063A05R
63 51.3 50 22 20 11
HSC100 JDMp09T320
0.4 TS351 AMS3 AJS30
10T10 ASS2 xTKY10D 30H
ZDSR-pp
47 10.4 6.3 17 1.5 0.4
HSC100
30H
JDMp
60 10.4 6.3 17 1.5 0.7
AJS40
-080A06R
80 68.3 50 27 23 13
76 12.4 7
19 1.5 1.2
-100A07R
7 100 88.3 63 32 26 17
96 14.4 8
26 1.5 2.6
AJX14-063A04R
63 51.1 50 22 20 11
60 10.4 6.3 17 2
0.7
-080A05R
80 68.1 50 27 23 13
76 12.4 7
19 2
1.2
-100A06R
6 100 88.1 63 32 26 17
96 14.4 8
26 2
2.4 TS54
-125B07R
7 125 113.2 63 40 40 56 100 16.4 9
2
3.3
-160B08R
8 160 148.2 63 40 40 56 100 16.4 9
2
5.0
Mass
AJX12-050A03R
Order Number
Stock
Number of Teeth
Fine Pitch
MILLING
Coarse Pitch
Type
y ARBOR TYPE
AJX12
AJX14
A.R :+8
A.R :+8
R.R :-5 -4 R.R :-3
Dimensions (mm)
D1
D6
Insert Clamp Clamp Bridge

L8 D11 A2 (kg) Screw Bridge Screw Spring Wrench Set Bolt Insert
HSC100 JDMp120420
47 10.4 6.3 17 1.5 0.4 TS43 AMS4 AJS40
ZDSR-pp
HSC100
60 10.4 6.3 17 2 0.7
30H
HSC120
76 12.4 7 19 2 1.2
35H
JDMp
AJS50
140520
96 14.4 8 26 2 2.4 TS54 AMS5 14T25 ASS3 zTKY25T HSC160
40H
ZDSR-pp
100 16.4 9
2 3.3
MBA200
40H
100 16.4 9
2 5.0
L1 D9 L7 D8 D12 W1
50 22 20 11
47 10.4 6.3 17 1
TS43
AMS4
ASS2 zTKY15T
120420
HSC120
35H ZDSR-pp
HSC160
40H
HSC100
30H
HSC120
35H
JDMp
AJS50
ASS3 zTKY25T HSC160
140520
AMS5
40H
14T25
ZDSR-pp
MBA200
40H
12T15
K092
METRIC Standard
AJX09
A.R :+8
R.R :-6
AJX14R06303B
R08004D
80 68.1 63 31.75 (1.25") 32 17 76 12.7 8 26 2
R10005D
5 100 88.1 63 31.75 (1.25") 32 17 96 12.7 8 26 2
2.4 TS54
R12505E
5 125 113.2 63 38.1
(1.5") 40 56 100 15.9 10 2
3.3
R16006F
6 160 148.2 63 50.8
(2.0") 43 72 100 19.1 11 2
5.0
AJX12R05004B
50 38.3 50 22.225 (.875") 19 11 47 8.4 5 17 1.5 0.4 TS43
AJX14R06304B
63 51.1 50 22.225 (.875") 19 11 60 8.4 5 17 2
0.7
R08005D
80 68.1 63 31.75 (1.25") 32 17 76 12.7 8 26 2
1.3
R10006D
6 100 88.1 63 31.75 (1.25") 32 17 96 12.7 8 26 2
R12507E
7 125 113.2 63 38.1
(1.5") 40 56 100 15.9 10
R16008F
8 160 148.2 63 50.8
(2.0") 43 72 100 19.1 11
AJX09R05005B
50
AJX12R06305B
63 51.3 50 22.225 (.875") 19 11 60 8.4 5
R08006D
80 68.3 63 31.75 (1.25") 32 17 76 12.7 8
R10007D
7 100 88.3 63 31.75 (1.25") 32 17 96 12.7 8
Mass
AJX12R05003B
Insert Clamp Clamp Bridge

L7 D8 D12 W1 L8 D11 A2 (kg) Screw Bridge Screw Spring Wrench Set Bolt Insert
HSC100 JDMp120420
50 38.3 50 22.225 (.875") 19 11 47 8.4 5 17 1.5 0.4 TS43 AMS4 AJS40
ZDSR-pp
HSC100
63 51.1 50 22.225 (.875") 19 11 60 8.4 5 17 2 0.7
30H
Order Number
Stock
Number of Teeth
Extra Fine Pitch
Fine Pitch
Coarse Pitch
Type
y ARBOR TYPE
AJX14
AJX12
A.R :+8
A.R :+8
R.R :-5 -4 R.R :-3
Dimensions (mm)
D1 D6 L1
D9
40 50 22.225 (.875") 19 11 47 8.4 5
1.3
HSC160 JDMp
40H
140520
MBA200 ZDSR-pp
40H
MBA240
45H
HSC100 JDMp120420
AMS4 AJS40
ASS2
zTKY15T
30H
12T15
ZDSR-pp
HSC100
30H
AJS50
AMS5 14T25 ASS3 zTKY25T
HSC160 JDMp
40H
140520
ZDSR-pp
MBA200
2 3.3
40H
MBA240
2 5.0
45H
HSC100 JDMp09T320
ASS2
xTKY10D
17 1 0.5 TS351 AMS3 AJS30
10T10
30H
ZDSR-pp
HSC100
17 1.5 0.9
30H
JDMp
AJS40
26 1.5 1.7 TS43 AMS4 12T15 ASS2 zTKY15T HSC160 120420
40H ZDSR-pp
26 1.5 2.9
2.4 TS54
AJS50
AMS5 14T25 ASS3 zTKY25T
MILLING
For inch arbors
INSERTS
K095
SPARE PARTS
M001
TECHNICAL DATA
N001
K093
MILLING
Fig.1
Fig.2
Fig.3
Section A-A
METRIC Standard
y SCREW-IN TYPE
MILLING
*
*
K094
Dimensions (mm)
2
* ap A2
D1 D4 D5 D6 L1 L2 L11 H1 M
Type (Fig.)
Number of Teeth
Stock
R
Coolant Thru
Order Number

Screw Bridge
Screw
Insert
AJX06R162AM0830
s u
2 16 8.5 13 8.9 48 30 6 10 M8 1.0 0.3 1 TS25
zTKY08F
172AM0830
s u
2 17 8.5 13 9.9 48 30 6 10 M8 1.0 0.3 1 TS25
zTKY08F
203AM1030
s u
3 20 10.5 18 12.9 49 30 6 14 M10 1.0 0.3 3 TS25
JOMp
06T215
zTKY08F ZZSR-pp
223AM1030
s u
3 22 10.5 18 14.9 49 30 6 14 M10 1.0 0.3 3 TS25
zTKY08F
AJX08R202AM1030
s u
2 20 10.5 18 11.4 49 30 6 14 M10 1.5 0.5 2 TS33
zTKY08D
222AM1030
s u
2 22 10.5 18 13.4 49 30 6 14 M10 1.5 0.5 2 TS33
zTKY08D
253AM1235
s u
3 25 12.5 21 16.4 57 35 6 19 M12 1.5 0.5 1 TS33
JOMp
080320
zTKY08D ZZSR-pp
283AM1235
s u
3 28 12.5 21 19.4 57 35 6 19 M12 1.5 0.5 1 TS33
zTKY08D
AJX09R252AM1235
s u
2 25 12.5 21 14.9 57 35 6 19 M12 2.0 1.0 2 TS351 AMS3 AJS3010T10 ASS2 xTKY10D
282AM1235
s u
303AM1645
s u
323AM1645
s u
JDMp
09T320
3 32 17.0 29 21.9 68 45 6 24 M16 2.0 1.0 1 TS351 AMS3 AJS3010T10 ASS2 xTKY10D ZDSR-pp
353AM1645
s u
404AM1645
s u
AJX12R302AM1645
s u
322AM1645
s u
352AM1645
JDMp
120420
s u 2 35 17.0 29 23.3 68 45 6 24 M16 2.0 1.5 2 TS43 AMS4 AJS4012T15 ASS2 xTKY15D ZDSR-pp
403AM1645
s u
1 Clamp Torque (lbf-in) : TS25=8.9, TS33=8.9, TS351=22, TS407=31, TS43=31, AJS3010T10=22, AJS4012T15=31

INSERTS
Work
Material
P
M
K
S
H
Steel
Stainless Steel
Cast Iron
Hardened Materials
: Stable Cutting
Class
FH7020
VP15TF
VP30RT
B3
JOMW06T215ZZSR-FT
a a a
13
.250
.109
.047
.059
080320ZZSR-FT
a a a
13
.315
.125
.055
.079
JDMW09T320ZDSR-FT
a a a
15
.375
.156
.071
.079
120420ZDSR-FT
a a a
15
.472
.187
.098
.079
140520ZDSR-FT
a a a
15
.551
.219
.110
.079
JDMT120420ZDSR-ST
a a a
15
.472
.187
.098
.079
140520ZDSR-ST
a a a
15
.551
.219
.110
.079
JOMT06T215ZZSR-JM
a a a
13
.250
.109
.047
.059
080320ZZSR-JM
a a a
13
.315
.125
.055
.079
JDMT09T320ZDSR-JM
a a a
15
.375
.156
.071
.079
120420ZDSR-JM
a a a
15
.472
.187
.098
.079
140520ZDSR-JM
a a a
15
.551
.219
.110
.079
Shape
Lower Cutting
Resistance
Order Number
: Unstable Cutting
Dimensions (inch)
Coated
Strong Cutting
Edge
: General Cutting
D1
S1
F1
Re
Geometry
(Note) Setting heights for ST chipbeaker and the other chipbreakers differ slightly.
If an ST type chipbreaker is used, please check the tool length offset height.
NOTE FOR PROGRAMMING
cut
Un
tion
por
When using the AJX,

please program the approximate
radius as indicated.
The approximate uncut portions for
the program are as follows.
MILLING
Insert
JOMo06T215ZZSR-oo
JOMo080320ZZSR-oo
JDMo09T320ZDSR-oo
JDMo120420ZDSR-oo
JDMo140520ZDSR-oo
Approx. R(inch) Uncut portion K(inch)
.079
.098
.118
.118
.118
.013
.018
.019
.025
.025
(Note) The uncut portion may change slightly depending on cutting conditions.
SCREW-IN ARBORS
K142
SPARE PARTS
M001
TECHNICAL DATA
N001
K095
MILLING
Work Material
Hardness
Grade
Cutting
Speed
(SFM)
& .625", & .688"

(& 16mm, & 17mm)
(Shank type)
& .750", & .875"

(& 20mm, & 22mm)
(Shank type)
& .750"
(& 20mm)
(Shank type)
AJXU06 Type
AJXU08 Type
AJXU06 Type
2 (Number of Teeth)
2 (Number of Teeth)
3 (Number of Teeth)
Over- Axial Feed per Over- Axial Feed per Over- Axial Feed per
hang Depth of Cut Tooth
(inch) (inch) (inch/tooth) (inch) (inch) (inch/tooth) (inch) (inch) (inch/tooth)
< 180HB
FH7020
Carbon Steel
180 280HB
FH7020
VP15TF
850
(700 1000)
550
(400 700)
Alloy Steel
280 350HB
Alloy Tool Steel
< 350HB
FH7020
VP15TF
450
(300 600)
< 35HRC
FH7020
VP15TF
35 43HRC
VP15TF
390
(260 520)
330
(230 430)
Stainless Steel
< 270HB
VP30RT
450
(300 600)
Gray Cast Iron
Tensile strength
< 350MPa
FH7020
850
(700 1000)
Ductile Cast Iron
Tensile strength
< 800MPa
VP15TF
550
(400 700)
Hardened Steel
43 55HRC
VP15TF
230
(160 300)
Mild Steel
Pre-hardened Steel
Work Material
MILLING
K096
Grade
Mild Steel
< 180HB
FH7020
Carbon Steel
180 280HB
FH7020
VP15TF
Alloy Steel
280 350HB
Alloy Tool Steel
< 350HB
FH7020
VP15TF
< 35HRC
FH7020
VP15TF
3 5 43HRC
VP15TF
Stainless Steel
< 270HB
VP30RT
Gray Cast Iron
Tensile strength
< 350MPa
FH7020
Ductile Cast Iron
Tensile strength
< 800MPa
VP15TF
Hardened Steel
43 55HRC
VP15TF
Pre-hardened Steel
Hardness
Cutting
Speed
(SFM)
5.5
7.0
8.2
5.5
7.0
8.2
5.5
7.0
8.2
5.5
7.0
8.2
5.5
7.0
8.2
5.5
7.0
8.2
5.5
7.0
8.2
.031
.024
.016
.028
.020
.012
.028
.020
.012
.031
.024
.016
.031
.024
.016
.028
.020
.012
.020
.016
.012
.031
.024
.016
.031
.024
.016
.028
.020
.012
.028
.020
.012
.039
.031
.024
.031
.024
.016
.020
.012
.008
6.3
8.3
9.4
6.3
8.3
9.4
6.3
8.3
9.4
6.3
8.3
9.4
6.3
8.3
9.4
6.3
8.3
9.4
6.3
8.3
9.4
.039
.031
.024
.031
.024
.016
.031
.024
.016
.039
.031
.024
.039
.031
.024
.031
.024
.016
.020
.016
.012
.039
.031
.024
.039
.031
.024
.031
.024
.016
.031
.024
.016
.047
.039
.031
.039
.031
.024
.024
.016
.008
6.3
8.3
9.4
6.3
8.3
9.4
6.3
8.3
9.4
6.3
8.3
9.4
6.3
8.3
9.4
6.3
8.3
9.4
6.3
8.3
9.4
.035
.028
.020
.028
.020
.016
.028
.020
.016
.035
.028
.020
.035
.028
.020
.028
.020
.016
.020
.016
.012
.035
.028
.020
.035
.028
.020
.028
.020
.012
.028
.020
.012
.039
.031
.024
.035
.028
.020
.020
.016
.008
& 1.500"
(& 40mm)
(& 1.500"shank)
& 2.000"
(& 50mm)
(Shank type)
& 2.000", & 2.500"

(& 50mm, & 63mm)
(Arbor type)
AJXU12 Type
AJXU14 Type
AJXU12 Type ( & 2.000")

AJXU14 Type (& 2.500")
3 (Number of Teeth)
3 (Number of Teeth)
Over- Axial Feed per Over- Axial Feed per

(inch) (inch) (inch/tooth) (inch) (inch) (inch/tooth)
850
7.0 .047
.059
7.0 .055
.059
(700 1000)
9.5
.039
.051
9.5
.047
.051
550
12.0 .031
.043

(400 700)
7.0 .039
.059
7.0 .047
.059
450
9.5 .031
.051
9.5 .039
.051
(300 600)
12.0 .024
.043

390
7.0 .039
.051
7.0 .047
.051
(260 520)
9.5 .031
.043
9.5 .039
.043
330
12.0 .024
.035

(230 430)
7.0 .047
.051
7.0 .055
.051
450
9.5 .039
.043
9.5 .047
.043
(300 600)
12.0 .031
.035

7.0 .047
.067
7.0 .055
.067
850
9.5 .039
.059
9.5 .047
.059
(700 1000)
12.0 .031
.051

7.0 .039
.059
7.0 .047
.059
550
9.5 .031
.051
9.5 .039
.051
(400 700)
12.0 .024
.043

7.0 .024
.043
7.0 .031
.043
230
9.5 .020
.035
9.5 .024
.035
(160 300)
12.0 .016
.028

3 or 4 (Number of Teeth)
Over- Axial Feed per
(inch) (inch) (inch/tooth)
6.0
10.0
14.0
6.0
10.0
14.0
6.0
10.0
14.0
6.0
10.0
14.0
6.0
10.0
14.0
6.0
10.0
14.0
6.0
10.0
.059
.051
.043
.051
.043
.035
.051
.043
.035
.059
.051
.043
.059
.051
.043
.051
.043
.035
.035
.028
.059
.051
.043
.059
.051
.043
.051
.043
.035
.051
.043
.035
.067
.059
.051
.059
.051
.043
.043
.035
& 1.500"
(& 40mm)
(& 1.250"shank)
AJXU09 Type
& 1.500"
(& 40mm)
(& 1.250"shank)
AJXU12 Type
3 (Number of Teeth)
3 (Number of Teeth)
4 (Number of Teeth)
& 1.000", & 1.125"

(& 25mm, & 28mm)
(Shank type)
& 1.000"
(& 25mm)
(Shank type)
& 1.250"
(& 32mm)
(Shank type)
& 1.250"
(& 32mm)
(Shank type)
AJXU09 Type
AJXU08 Type
AJXU12 Type
2 (Number of Teeth)
3 (Number of Teeth)
2 (Number of Teeth)
AJXU09 Type
Over- Axial Feed per Over- Axial Feed per Over- Axial Feed per Over- Axial Feed per Over- Axial Feed per Over- Axial Feed per
(inch) (inch) (inch/tooth) (inch) (inch) (inch/tooth) (inch) (inch) (inch/tooth) (inch) (inch) (inch/tooth) (inch) (inch) (inch/tooth) (inch) (inch) (inch/tooth)
.039
.031
.024
.031
.024
.016
.031
.024
.016
.039
.031
.024
.039
.031
.024
.031
.024
.016
.020
.016
.012
.047
.039
.031
.047
.039
.031
.039
.031
.024
.039
.031
.024
.055
.047
.039
.047
.039
.031
.031
.024
.016
& 2.000", & 2.500"

(& 50mm, & 63mm)
(Arbor type)
AJXU09 Type ( & 2.000")
AJXU12 Type (& 2.500")
5 (Number of Teeth)
Overhang
(inch)
6.0
10.0
14.0
6.0
10.0
14.0
6.0
10.0
14.0
6.0
10.0
14.0
6.0
10.0
14.0
6.0
10.0
14.0
6.0
10.0
Axial Feed per

Depth of Cut Tooth
(inch) (inch/tooth)
.053
.051
.046
.043
.039
.035
.046
.051
.039
.043
.032
.035
.046
.043
.039
.035
.032
.028
.053
.043
.046
.035
.039
.028
.053
.059
.046
.051
.039
.039
.046
.051
.039
.043
.032
.035
.032
.039
.025
.031

6.7
9.0
11.5
6.7
9.0
11.5
6.7
9.0
11.5
6.7
9.0
11.5
6.7
9.0
11.5
6.7
9.0
11.5
6.7
9.0
11.5
.035
.028
.020
.028
.020
.016
.028
.020
.016
.035
.028
.020
.035
.028
.020
.028
.020
.016
.020
.016
.012
.039
.031
.024
.039
.031
.024
.035
.028
.020
.035
.028
.020
.047
.039
.031
.039
.031
.024
.028
.020
.012
7.0
9.0
11.0
7.0
9.0
11.0
7.0
9.0
11.0
7.0
9.0
11.0
7.0
9.0
11.0
7.0
9.0
11.0
7.0
9.0
11.0
.047
.039
.031
.039
.031
.024
.039
.031
.024
.047
.039
.031
.047
.039
.031
.039
.031
.024
.024
.020
.016
.055
.047
.039
.055
.047
.039
.047
.039
.031
.047
.039
.031
.063
.055
.047
.055
.047
.039
.039
.031
.024
&3.000", &4.000", &4.921", &6.299"

& 3.000", & 4.000"
(& 80mm, &100mm, &125mm, &160mm) (& 80mm, & 100mm)
(Arbor type)
(Arbor type)
AJXU14 Type
AJX14 Type
4 or 5 or 6 or 7 or 8
(Number of Teeth)
Overhang
(inch)
7.0
12.0
18.0
7.0
12.0
18.0
7.0
12.0
18.0
7.0
12.0
18.0
7.0
12.0
18.0
7.0
12.0
18.0
7.0
12.0
Axial Feed per

Depth of Cut Tooth
(inch) (inch/tooth)
.059
.059
.051
.051
.039
.039
.051
.059
.043
.051
.031
.039
.051
.051
.043
.043
.031
.031
.059
.051
.051
.043
.039
.031
.059
.067
.051
.059
.039
.047
.051
.059
.043
.051
.031
.039
.035
.043
.028
.035

7.0
9.0
11.5
7.0
9.0
11.5
7.0
9.0
11.5
7.0
9.0
11.5
7.0
9.0
11.5
7.0
9.0
11.5
7.0
9.0
11.5
.043
.035
.028
.035
.028
.020
.035
.028
.020
.043
.035
.028
.043
.035
.028
.035
.028
.020
.020
.016
.012
.047
.039
.031
.047
.039
.031
.039
.031
.024
.039
.031
.024
.055
.047
.035
.047
.039
.031
.035
.028
.020
7.0
9.5
12.0
7.0
9.5
12.0
7.0
9.5
12.0
7.0
9.5
12.0
7.0
9.5
12.0
7.0
9.5
12.0
7.0
9.5
12.0
.047
.039
.031
.039
.031
.024
.039
.031
.024
.047
.039
.031
.047
.039
.031
.039
.031
.024
.024
.020
.016
.055
.047
.039
.055
.047
.039
.047
.039
.031
.047
.039
.031
.063
.055
.047
.055
.047
.039
.039
.031
.024
7.0
9.5
12.0
7.0
9.5
12.0
7.0
9.5
12.0
7.0
9.5
12.0
7.0
9.5
12.0
7.0
9.5
12.0
7.0
9.5
12.0
.043
.035
.028
.035
.028
.020
.035
.028
.020
.043
.035
.028
.043
.035
.028
.035
.028
.020
.020
.016
.012
.047
.039
.031
.047
.039
.031
.039
.031
.024
.039
.031
.024
.055
.047
.035
.047
.039
.031
.035
.028
.020
zOverhang length
AJXU12 Type
6 or 7 (Number of Teeth)
Overhang
(inch)
7.0
12.0
18.0
7.0
12.0
18.0
7.0
12.0
18.0
7.0
12.0
18.0
7.0
12.0
18.0
7.0
12.0
18.0
7.0
12.0
Axial Feed per

Depth of Cut Tooth
(inch) (inch/tooth)
.053
.051
.046
.043
.035
.031
.046
.051
.039
.043
.028
.031
.046
.043
.039
.035
.028
.024
.053
.043
.046
.035
.035
.024
.053
.059
.046
.051
.035
.035
.046
.051
.039
.043
.028
.031
.032
.039
.025
.031

Overhang length
(GL:Gage Length)
xMain spindle speed

N(min-1)=(Recommended cutting speed x 12) (outer tool diameter x 3.14)
cTable feed rate
vf(inch/min)=N x feed per tooth x number of teeth
vRecommended width of cut (ae) is more than 60% of cutter
diameter.
MILLING
6.7
9.0
11.5
6.7
9.0
11.5
6.7
9.0
11.5
6.7
9.0
11.5
6.7
9.0
11.5
6.7
9.0
11.5
6.7
9.0
11.5
bThe above cutting conditions are a guide when using a

CAT50 size holder. In case of CAT40 and HSK63 machines,
a cutter diameter of under 1.5 inch is recommended.
In this case, reduce the depth of cut and table feed rate.
nUse of ST chipbreaker with a tougher cutting edge is
recommended for interrupted cutting. For tough
applications,VP30RT is recommended.
mA cutter body with a coarse pitch is recommended for use in
unstable conditions such as a long tool overhang.
,Use "sharp" JM chipbreaker to lower cutting forces or
when there is a long tool overhang.
.Large chips are generated when machining with the AJX.
To avoid chip jamming-related problems, machine using an
air blow to disperse the chips effectively.
K097
MILLING
MAXIMUM CAPACITIES BY MODE
y RAMPING
y HELICAL CUTTING
a How to calculate the theoretical
center of the tool path.
dc = DH - D1
Theoretical
center
of the tool
Desired hole
diameter
Cutting edge
diameter
a Please set the depth of cut per
cycle under max. depth of cut (ap).

a Please machine in a down cutting
direction (climb milling).

a When ramping and helical cutting, it is recommended to reduce the feed rate by 40%.
a When drilling, please set the feed in the axial direction .008 inch/rev or less.
a The long chips generated can discharge in any direction, so ensure that adequate safety precautions are taken.
Ramp machining
K098
Arbor Type
MILLING
Shank Type
Holder Type
Tool
Width of Max. Depth
Diameter Face Cut
of Cut
(inch)
(inch)
ap (inch)
Max.
Angle
Helical Cutting
Required X distance
for Z inch depth (inch)
Z=.039
Z=.059
Z=.079
Max. Drilling
Min. Hole Max. Hole Depth
Diameter Diameter A2 (inch)
(inch)
(inch)
AJXU06R102
.625
.340
.039
3.0
.744
.900
1.130
.012
06R112
.688
.400
.039
2.5
.893
1.020
1.260
.012
06R123
.750
.472
.039
1.7
1.314
1.150
1.380
.012
08R122
.750
.410
.059
3.5
.638
.965
.990
1.340
.020
08R142
.875
.530
.059
3.0
.744
1.126
1.240
1.590
.020
08R163
1.000
.661
.059
2.0
1.117
1.690
1.490
1.840
.020
09R162
1.000
.590
.079
4.0
.558
.844
1.130
1.330
1.840
.039
09R182
1.125
.720
.079
3.0
.744
1.126
1.507
1.580
2.090
.039
09R203
1.250
.854
.079
3.3
.676
1.023
1.370
1.830
2.340
.039
09R244
1.500
1.114
.079
2.4
.931
1.408
1.885
2.330
2.840
.039
12R202
1.250
.790
.079
4.0
.558
.844
1.130
1.590
2.340
.059
12R243
1.500
1.040
.079
3.0
.744
1.126
1.507
2.090
2.840
.059
14R323
2.000
1.530
.079
4.2
.531
.803
1.076
2.900
3.840
.079
AJXU09R02
2.000
1.606
.079
1.1
2.031
3.073
4.114
3.330
3.840
.039
12R02
2.000
1.540
.079
2.0
1.117
1.690
2.262
3.090
3.840
.059
12R2505
2.500
2.039
.079
1.5
1.489
2.253
3.017
4.090
4.840
.059
12R0306
3.000
2.543
.079
1.2
1.862
2.817
3.771
5.090
5.840
.059
12R0407
4.000
3.539
.079
0.8
2.793
4.225
5.658
7.090
7.840
.059
14R25
2.500
2.030
.079
2.8
.797
1.206
1.615
3.900
4.840
.079
14R03
3.000
2.530
.079
1.8
1.241
1.877
2.514
4.900
5.840
.079
14R04
4.000
3.530
.079
1.2
1.862
2.817
3.771
6.900
7.840
.079
AJX14RA125
4.920
4.530
.079
.8
2.793
4.225
5.658
8.740
9.680
.079
14RA160
6.300
5.830
.079
.5
4.469
6.761
9.053
11.500
12.440
.079
MULTI FUNCTIONAL
MILLING
ARX
Light Alloy
Cast Iron
Including
Flat faces
Roughing
Fig.1 (Type with the center cutting edge)
Fig.2 (Type without the center cutting edge (multi-tooth))

a Precision M-class
15positive insert.
a Effective for various
machining applications.
METRIC Standard
30R203SA20S
25R224SA20S
30R224SA20S
25R255SA20S
30R254SA20S
20
120
20
11
180
20
10
180
20
16
12
180
20
16
11
180
20
20
20
15
180
3.0
20
20
14
2.5
22
20
17
3.0
22
20
2.5
25
20
3.0
25
20
Type (Fig.)
Number of Teeth
25R204SA20S
Coolant Thru
30R173SA16S
25R173SA16S
140
30R163SA16S
25R163SA16S
20
20
120
120
2.5
35R142SA12S
ARX25R122SA10S
30R122SA10S
L2
ARX25R102SA10S
the Center
Without the Center Cutting Edge (Multi-tooth) With
Cutting Edge
Order Number
Stock
Type
y STEEL SHANK TYPE
Insert Screw
Wrench
Insert
TPS20
TIP06F
RDMW0517M0E
TPS22S
TIP07FS
RDMW0620M0E
TPS22
TIP07FS
RDMW0724M0E
TPS20
TIP06F
RDMW0517M0E
TPS20
TIP06F
RDMW0517M0E
TPS22
TIP07FS
RDMW0620M0E
TPS20
TIP06F
RDMW0517M0E
TPS22
TIP07FS
RDMW0620M0E
20
TPS20
TIP06F
RDMW0517M0E
180
20
TPS22
TIP07FS
RDMW0620M0E
180
20
TPS20
TIP06F
RDMW0517M0E
16
180
20
TPS22
TIP07FS
RDMW0620M0E
20
180
20
TPS20
TIP06F
RDMW0517M0E
19
180
20
TPS22
TIP07FS
RDMW0620M0E
Dimensions (mm)
D1
D4
D6
10
10
3.0
12
10
3.5
14
12
2.5
12
10
2.5
16
16
3.0
16
16
2.5
17
3.0
17
2.5
L1
Clamp Torque (lbf-in) : TPS20=5.3, TPS22=5.3, TPS22S=5.3
Using the ARX Effectively (Reducing Unremoved Material)

Ball nose end milling
To reduce
unremoved material,
the pick feed needs
to be reduced.
(Machining efciency
will decrease.)
MILLING
Unremoved material
(cusp height)
a When Milling Even Surfaces
With the use of the ARX

Higher machining
efciency
Even with a large
pick feed, no unremoved
material will remain.
Pf
Pf
a When Milling Corner Radius

With the use of the ARX
Ball nose end milling

To machine small corner
radii, the tool diameter
needs to be reduced.
(Tool rigidity will
decrease.)
A large shank diameter offering high rigidity can

also machine small corner radii.
(The cutting load of a subsequent nishing tool
will be decreased thereby lengthening its tool
life. Surface nish quality
will be improved.)
La
rge
Sm
all
rad
ius
ra
diu
INSERTS
K100
SPARE PARTS
M001
TECHNICAL DATA
N001
K099
MILLING
Fig.1
Fig.2
Fig.3
METRIC Standard
ARX25R122SA10LW
D4
D6
L1
L2
2.5
10
10
150
40
3.0
12
10
150
3.5
14
12
170
2.5
12
10
150
Type (Fig.)
35R142SA12LW
Number of Teeth
30R122SA10LW
Coolant Thru
D1
ARX25R102SA10LW
Without the Center

With the Center
Cutting Edge (Multi-tooth) Cutting Edge
Order Number
Stock
Type
y CARBIDE SHANK TYPE
Insert Screw
Wrench
Insert
TPS20
TIP06F
RDMW0517M0E
40
TPS22S
TIP07FS
RDMW0620M0E
40
TPS22
TIP07FS
RDMW0724M0E
40
TPS20
TIP06F
RDMW0517M0E
Dimensions (mm)
* Clamp Torque (lbf-in) : TPS20=5.3, TPS22=5.3, TPS22S=5.3

INSERTS
MILLING
Shape
K100
VP15TF
MP8010
Coated Dimensions (mm)

D1
RDMW0517M0E
s s
5.0
1.70
0620M0E
s s
6.0
1.99
0724M0E
s s
7.0
2.38
Order Number

S1
Geometry
Section A-A
METRIC Standard
y SCREW-IN TYPE
203M10A30
224M10A30
254M12A35
10 M8
0.1
TPS20
TIP06F
RDMW0517M0E
14 M10 0.2
TPS20
TIP06F
RDMW0517M0E
14 M10 0.2
TPS20
TIP06F
RDMW0517M0E
19 M12 0.2
TPS20
TIP06F
RDMW0517M0E
30
10 M8
0.1
TPS22
TIP07FS
RDMW0620M0E
8.5 14.5 48
30
10 M8
0.1
TPS22
TIP07FS
RDMW0620M0E
3.0
20 10.5 18.5 49
30
14 M10 0.2
TPS22
TIP07FS
RDMW0620M0E
3.0
22 10.5 18.5 49
30
14 M10 0.2
TPS22
TIP07FS
RDMW0620M0E
3.0
25 12.5 23.4 57
35
19 M12 0.2
TPS22
TIP07FS
RDMW0620M0E
Mass
Coolant Thru
173M08A30
Number of Teeth
Stock
s
ARX30R163M08A30
RDMW0517M0E
TIP06F
255M12A35
TPS20
224M10A30
0.1
10 M8
204M10A30
2.5
173M08A30
Dimensions (mm)
D1
D4
L1
L2
L11
16
8.5 14.7 48
30
2.5
17
8.5 14.5 48
30
2.5
20 10.5 18.6 49
30
2.5
22 10.5 18.5 49
30
2.5
25 12.5 23.6 57
35
3.0
16
8.5 14.6 48
3.0
17
D5
H1
M*
(kg) Insert Screw
Wrench
Insert
1 Clamp Torque (lbf-in) : TPS20=5.3, TPS22=5.3

2 Clamp Torque of the Head (lbf-ft) : M8=17.1, M10=33.8, M12=59.2
MILLING
*
*
ARX25R163M08A30
Order Number

1
SCREW-IN ARBORS
K100
SPARE PARTS
M001
TECHNICAL DATA
N001
K101
MILLING
(Note) The cutting conditions below are a guide only.

y SHOULDER POCKET RAMPING COPYING

Work Material
Hardness
Grade
Cutting Speed ARX25RpppSAppS ARX30RpppSAppS ARX35RpppSAppS

vc
(SFM)
ap (inch) fz (inch/tooth) ap (inch) fz (inch/tooth) ap (inch) fz (inch/tooth)
Mild Steel
< 180HB
VP15TF 590 (490 720)
<.039
<.020
<.047
<.020
<.059
<.020
180 350HB
VP15TF 525 (395 655)
<.028
<.012
<.035
<.012
<.047
<.012
< 270HB
VP15TF 490 (395 590)
<.028
<.012
<.035
<.012
<.047
<.012
Tensile strength<450MPa VP15TF 590 (490 720)
<.039
<.020
<.047
<.020
<.059
<.020
<.020
<.008
<.028
<.008
<.039
<.008
Stainless Steel
Cast Iron
Hardened Steel
45 55HRC
VP15TF 260 (165 395)
(Note) When ramping, refer to the machining limits on page K103.
y SLOTTING
Work Material
Hardness
Grade

vc
(SFM)
ap (inch) fz (inch/tooth) ap (inch) fz (inch/tooth) ap (inch) fz (inch/tooth)
Mild Steel
< 180HB
VP15TF 590 (490 720)
<.039
<.016
<.047
<.016
<.059
<.016
180 350HB
VP15TF 525 (395 655)
<.028
<.008
<.035
<.008
<.047
<.008
Stainless Steel
< 270HB
VP15TF 490 (395 590)
<.028
<.008
<.035
<.008
<.047
<.008
Cast Iron
<.039
<.016
<.047
<.016
<.059
<.016
<.020
<.004
<.028
<.004
<.039
<.004
Hardened Steel
45 55HRC
VP15TF 260 (165 395)
y PLUNGING
Work Material
Hardness
Grade

vc
Width of Cut Feed per Tooth Width of Cut Feed per Tooth Width of Cut Feed per Tooth
(SFM)
ae (inch) fz (inch/tooth) ae (inch) fz (inch/tooth) ae (inch) fz (inch/tooth)
Mild Steel
< 180HB
VP15TF 590 (490 720)
<.098
<.012
<.118
<.012
<.138
<.012
180 350HB
VP15TF 525 (395 655)
<.098
<.008
<.118
<.008
<.138
<.008
Stainless Steel
< 270HB
VP15TF 490 (395 590)
<.098
<.008
<.118
<.008
<.138
<.008
<.098
<.012
<.118
<.012
<.138
<.012
<.098
<.004
<.118
<.004
<.138
<.004
Cast Iron
Hardened Steel
45 55HRC
VP15TF 260 (165 395)
y HELICAL DRILLING
MILLING
ARX25RpppSAppS
Work Material
Hardness
Grade
ARX35RpppSAppS
Mild Steel
< 180HB
VP15TF 590 (490 720)
<.039
<.012
<.039
<.012
<.039
<.012
180 350HB
VP15TF 525 (395 655)
<.028
<.008
<.035
<.008
<.039
<.008
< 270HB
VP15TF 490 (395 590)
<.028
<.008
<.035
<.008
<.039
<.008
<.039
<.012
<.039
<.012
<.039
<.012
<.020
<.004
<.028
<.004
<.039
<.004
Stainless Steel
Cast Iron
Hardened Steel
45 55HRC
VP15TF 260 (165 395)
(Note) When helical drilling, refer to the machining limits on page K103.
K102
ARX30RpppSAppS
Cutting Speed
vc
Per Pass
(SFM)
(
) Per Pass
(
) Per Pass
(
)
ap (inch/pass) fz inch/tooth ap (inch/pass) fz inch/tooth ap (inch/pass) fz inch/tooth
CUTTING MODE MAXIMUM CAPACITIES

y RAMPING
y HELICAL DRILLING
a Setting
Finding a cutters distance

moved L when depth of
cu t re a c h e s ap a t a
ramping angle of %.
a tools center excursion
1
dc = Required
DHbore- Tools
Dcutting
Tools center
excursion
diameter
the depth of cut per pass,

refer to the cutting conditions on page
K102 for helical drilling.
Cutting
direction
L=ap/tan % (mm)
diameter
a For
the machine spindle revolution so

that the tool is rotating and cutting
in a down cut direction.
Order Number
ARX 25R102SA10S
Number
R
(mm) of Teeth
Ramping
max. %
ap max. (mm)
Helical Drilling
L (mm)
DH min. (mm) DH max. (mm)
10
2.5
90
2.5
15
19
25R102SA10LW
10
2.5
90
2.5
15
19
30R122SA10S
12
3.0
90
3.0
18
23
30R122SA10LW
12
3.0
90
3.0
18
23
35R142SA12S
14
3.5
90
3.5
21
27
35R142SA12LW
14
3.5
90
3.5
21
27
12
2.5
27.17
2.5
4.87
19
23
25R122SA10LW
12
2.5
27.17
2.5
4.87
19
23
30R163SA16S
16
3.0
21.25
3.0
7.71
26
31
25R163SA16S
16
2.5
13.70
2.5
10.26
27
31
30R173SA16S
17
3.0
18.42
3.0
9.01
28
33
25R173SA16S
17
2.5
12.22
2.5
11.54
29
33
30R203SA20S
20
3.0
13.21
3.0
12.78
34
39
25R204SA20S
20
2.5
9.23
2.5
15.38
35
39
30R224SA20S
22
3.0
11.13
3.0
15.25
38
43
25R224SA20S
22
2.5
7.94
2.5
17.92
39
43
30R254SA20S
25
3.0
9.01
3.0
18.92
44
49
25R255SA20S
25
2.5
6.57
2.5
21.71
45
49
ARX 25R122SA10S
Without the Center Cutting Edge (Multi-tooth)
D1
(mm)
MILLING
With the Center Cutting Edge
Type
a Set
K103
MILLING
MULTI FUNCTIONAL
MILLING
BRP
Light Alloy
Cast Iron
Roughing
Fig.1
(Max. Depth of Cut)
*Please allow for an inclination angle of B +1

2
Fig.2
Fig.3
Fig.4
a Round shape insert gives strong cutting edge.
a A wide variety of lengths available.
a Suitable for machining of die and mold.
EL
.187
EL
.250
.312
EL
.500
.177 2.781
.500 1.000 .007 .146 2 56' 2 CS250560T zTKY08F
.625
.303 3.500
.625 1.000 .039 .146 2 56' 3 CS250560T zTKY08F
.750
.429 4.000
.750 1.250 .066 .146 2 16' 3 CS250560T zTKY08F
3 1.000
.681 4.500 1.000 1.250 .078 .146 2 16' 4 CS250560T zTKY08F zRPMW07T200E
BRP3UNR081LW08
.500
.177 6.000
101LW10
.625
.303 6.000
.625 2.800 .039 .146 0 56' 1 CS250560T zTKY08F
BRP3UNR122ELW12
.750
.429 10.000
.750 5.100 .066 .146 0 30' 1 CS250560T zTKY08F
163ELW16
3 1.000
.681 10.000 1.000 5.100 .078 .146 0 30' 1 CS250560T zTKY08F
BRP4UNR101W10
.625
.244 3.500
.625 1.000 .011 .177 3 3'
121W12
.750
.366 4.000
.750 1.250 .035 .177 2 20' 3 CS350760T zTKY15F
162W16
2 1.000
.618 4.500 1.000 1.250 .098 .177 2 20' 4 CS350760T zTKY15F
203W20
BRP3UNR081W08
101W10
122W12
163W16
Dimensions (inch)
L1
D4
L2
A2
ap
B2
Type (Fig.)
D6
Stock
D1
Order Number
Insert
Screw
Wrench
Insert
.500 2.800 .007 .146 0 56' 1 CS250560T zTKY08F xRPMT07T200E-JS
3 CS350760T zTKY15F
3 1.250
.866 5.000 1.250 1.750 .098 .177 1 35' 4 CS350760T zTKY15F zRPMW09T300E
BRP4UNR101LW10
.625
.244 6.000
.625 2.800 .011 .177 0 57' 1 CS350760T zTKY15F xRPMT09T300E-JS
121LW12
.750
.366 7.000
.750 3.900 .035 .177 0 40' 1 CS350760T zTKY15F
BRP4UNR162ELW16
2 1.000
.618 10.000 1.000 5.100 .098 .177 0 30' 1 CS350760T zTKY15F
203ELW20
3 1.250
.866 12.000 1.250 7.100 .098 .177 0 22' 1 CS350760T zTKY15F
BRP6UPR202W20
2 1.250
.744 5.000 1.250 1.750 .157 .240
TS43
xTKY15D
243W20
3 1.500
.976 5.000 1.250 1.750 .157 .240
TS43
xTKY15D
324W20
4 2.000 1.492 5.000 1.250 1.750 .157 .240
TS43
xTKY15D
405W20
5 2.500 1.999 5.000 1.250 1.750 .157 .240
TS43
xTKY15D
BRP6UPR202ELS20
2 1.250
.744 12.000 1.250 1.750 .157 .240
TS43
xTKY15D
243ELS20
3 1.500
.996 12.000 1.250 1.750 .157 .240
TS43
xTKY15D
324ELS20
4 2.000 1.492 12.000 1.250 1.750 .157 .240
TS43
xTKY15D
BRP7UPR323W20
3 2.000 1.370 5.000 1.250 1.750 .217 .302
TS54
xTKY25D
404W20
4 2.500 1.866 5.000 1.250 1.750 .217 .302
TS54
xTKY25D
3 2.000 1.370 12.000 1.250 1.750 .217 .302
TS54
xTKY25D
EL BRP7UPR323ELS20
R : Standard shank, L : Long shank, EL : Extra Long shank

*12 Type
Clamp Torque (lbf-in) : CS250560T=8.9, CS350760T=31, TS43=31, TS54=66
*
K104
Number of Teeth
.156
MILLING
Type 1
Corner Radius
y SHANK TYPE
a : Inventory maintained. r : Non stock, produced to order only.

zRPMW120400E
xRPMT120400E-JS
zRPMW150600E
xRPMT150600E-JS
Fig.1
Fig.2
Set Bolt
(Attached)
Use the attached set bolt.
y ARBOR TYPE
Corner
Radius
D7
L1
D9
L7
D8
W1
L8
Max. Depth of cut Type

A2
ap (Fig.)
1.500
.996 1.228 2.000
.750
.748
.313
.187
.157
.240
0204
2.000 1.492 1.715 2.000
.750
.748 .415
.313
.187
.157
.240
2505
2.500 1.992 2.214 2.000
.750
.748 .415
.313
.187
.157
.240
0306C
3.000 2.492 2.706 2.000 1.000 1.024 .539
.375
.219
.157
.240
0407E
4.000 3.492 3.696 2.500 1.500 1.181 .787
.625
.375
.157
.240
2.500 1.866 2.165 2.000
.750
.748 .415
.313
.187
.217
.302
0305C
3.000 2.366 2.649 2.000 1.000
.969 .539
.375
.219
.217
.302
0406E
4.000 3.366 3.631 2.500 1.500 1.122 .787
.625
.375
.217
.302
BRP7UPR2504
.312
D6
D1
BRP6UPR1503X
.250
Dimensions (inch)
Stock Number
R of Teeth
Order Number
Insert
RPMW120400E
RPMT120400E-JS
RPMW150600E
RPMT150600E-JS
SPARE PARTS
*
Insert Screw
Wrench
Set Screw
BRP6UPR1503X
BRP6UPR0204
TS43
TKY15D
HDSU37513
Tool Holder
Number
TS43
TKY15D
TS54
TKY25D
BRP6UPR0407E
BRP7UPR2504
BRP7UPR0406E

INSERTS
Steel
: Stable Cutting
Stainless Steel
Cast Iron
JS breaker
: Unstable Cutting

Hardened Materials
Order Number
Class
F7010
F7030
VP15TF
AP20M
Coated
Shape
: General Cutting
MILLING
Work
Material
P
M
K
S
H
Dimensions (inch)
D1
S1
RPMW07T200E
a a
.313
.109
09T300E
a a
120400E
150600E
.375
.156
a a
.500
.188
a a
.625
.250
RPMT07T200E-JS
a a
.313
.109
09T300E-JS
a a
.375
.156
120400E-JS
a a
.500
.188
150600E-JS
a r a a
.625
.250
Geometry
SPARE PARTS
M001
TECHNICAL DATA
N001
K105
MILLING
Cutting Speed (SFM)
CVD
PVD
F7010 / F7030 / F620
VP15TF / AP20M
Work Material
Material
Hardness
Mild Steel
< 180HB
820 (660 980)
820 (660 980)
Carbon Steel
180 280HB
590 (425 720)
590 (425 720)
Alloy Steel
280 380HB
525 (360 620)
525 (360 620)
Prehardened Steel
35 45HB
390 (260 460)
390 (260 460)
High Alloy Steel
< 300HB
425 (295 525)
425 (295 525)
Sintered Steel
45 60HRC
215 (155 275)
< 260HB
590 (425 720)
590 (425 720)
570 (425 720)
Tensile Strength 360500MPa
470 (340 600)
Tensile Strength 500800MPa
360 (260 460)
Stainless Steel
Gray Cast Iron

Ductile Cast Iron
FEED PER TOOTH (IPT) FOR STRAIGHT LINE (NON-RAMPING) CUTTING ONLY
Type
BRP3U
BRP4U
BRP6U
BRP7U
Depth of Cut (inch)
.040
.012
.014
.020
.024
.080
.009
.012
.016
.020
.120
.008
.010
.012
.018
.150
.006
.010
.012
.016
.180

.007
.011
.012
.200

.009
.013
.240

.008
.012
.280

.010
.320

.008
RAMPING
Type
BRP3U
MILLING
BRP4U
BRP6U
BRP7U
Min. Cutting Length According to Max. Ramp Angle L min. (inch)

Tool Diameter Max. Ramp Angle
Tan % per inch
(inch)
%Max.
ap = .094" ap = .125" ap = .156" ap = .188" ap = .250" ap = .281" ap = .312"
.500
.625
.750
1.000
.625
.750
1.000
1.250
1.250
1.500
2.000
2.500
3.000
4.000
2.000
2.500
3.000
4.000
3.71
12.34
13.50
8.48
4.07
8.41
12.98
8.18
17.3
11.78
7.15
5.13
3.99
2.77
11.49
7.88
5.99
4.04
.065
.219
.240
.149
.071
.148
.231
.144
.312
.209
.125
.090
.070
.048
.203
.138
.105
.071
1.446
.429
.392
.631
1.324
.635
.407
.653
.301
.450
.752
1.044
1.343
1.958
.463
.681
.895
1.324
1.923
.571
.521
.839
1.761
.845
.541
.868
.401
.598
1.000
1.389
1.786
2.604
.616
.906
1.190
1.761
2.400
.712
.650
1.047
2.197
1.054
.675
1.083
.500
.746
1.248
1.733
2.229
3.250
.768
1.130
1.486
2.197
Cutting
Direction
K106

2.648
1.270
.814
1.306
.603
.900
1.504
2.089
2.686
3.917
.926
1.362
1.790
2.648

.801
1.196
2.000
2.778
3.571
5.208
1.232
1.812
2.381
3.521

1.384
2.036
2.676
3.958

1.537
2.261
2.971
4.394
INTERPOLATING
CUTTING HOLE DIAMETER AND DEPTH OF CUT
Minimum
Cutting Diameter
Type
*1
BRP4U
BRP6U
BRP7U
*2
& dc
*1
Inclination Angle %
ap=.094" ap=.156" ap=.188" ap=.250" ap=.312"
ap max. =.039 | %=3.778
&DH max.
*2
& dc
Inclination Angle %
ap=.094" ap=.156" ap=.188" ap=.250" ap=.312"
ap max. =.078 | %= 3.367
.500
.688
.188
.922
.422
.625
.938
.313
5.461
9.015
1.172
.547
3.131
5.187
.750
1.188
.438
3.908
6.468
1.422
.672
2.549
4.226
1.000
1.688
.688
2.490
4.128
1.922
.922
1.859
3.083
.625
.874
.249
1.172
.547
3.131
5.187
6.243
ap max. =.039 | %=2.854
.750
1.124
.374
4.574
7.563
9.091
1.422
.672
2.549
4.226
5.089
1.000
1.624
.624
2.745
4.550
5.478
1.922
.922
1.859
3.083
3.714
1.250
2.124
.874
1.961
3.252
3.917
2.422
1.172
1.462
2.426
2.923
1.250
2.000
.750
2.285
3.788
4.562
6.057
2.422
1.172
1.462
2.426
2.923
3.884
1.500
2.500
1.000
1.714
2.843
3.425
4.550
2.922
1.422
1.205
2.000
2.410
3.203
2.000
3.500
1.500
1.143
1.896
2.285
3.037
3.922
1.922
.892
1.480
1.783
2.371
2.500
4.500
2.000
.857
1.422
1.714
2.279
4.922
2.422
.708
1.175
1.415
1.882
3.000
5.500
2.500
.686
1.138
1.371
1.823
5.922
2.922
.587
.974
1.173
1.560
4.000
7.500
3.500
.490
.813
.980
1.302
7.922
3.922
.437
.725
.874
1.162
2.000
3.376
1.376
1.246
2.067
2.490
3.310
4.128
3.922
1.922
.892
1.480
1.783
2.371
2.958
2.500
4.376
1.876
.914
1.516
1.827
2.429
3.030
4.922
2.422
.708
1.175
1.415
1.882
2.348
3.000
5.376
2.376
.721
1.197
1.443
1.918
2.393
5.922
2.922
.587
.974
1.173
1.560
1.947
4.000
7.376
3.376
.508
.842
1.016
1.350
1.685
7.922
3.922
.437
.725
.874
1.162
1.451
1 DH = Cutting Hole Diameter : & (inch)

2 dc = Tool Pass Diameter : & (inch)
DH max. = (D1-.039) X 2,
ap max. =.156 (inch)
DH min. = (D1-.156) X 2,
BRP3U type
DH min. = (D1-.188) X 2,
DH max. = (D1-.039) X 2,
BRP4U type
DH min. = (D1-.250) X 2,
DH max. = (D1-.039) X 2,
BRP6U type
DH min. = (D1-.312) X 2,
DH max. = (D1-.039) X 2,
BRP7U type
dc = DH-D1
DH min. (Minimum Cutting Diameter) DH max.(Maximum Cutting Diameter) ap max. (Maximum Depth of Cut)
MILLING
*
*
DH max.
Tool
Diameter
& D1
(inch)
&DH min.
BRP3U
Maximum
Cutting Diameter
DH min.
K107
MILLING
MULTI FUNCTIONAL
MILLING
BOE
Light Alloy
Cast Iron
Roughing
Fig.1 (BOE4 type)

(Inner)
.197"
(Max. Depth of Cut)ap
a Compatible with 8-corner use insert
Fig.2 (BOE type)
and round type insert.

a Multi functional milling.
BOE4R202W20
243W20
323W20
404W20
BOER322W20
403W20
504W20
a
a
a
a
a
a
a
Number of Teeth
Order Number
Stock
y WELDON SHANK TYPE
D1
D6
D3
L1
D4
L2
A1
ap
A2
2
3
3
4
2
3
4
1.250
1.500
2.000
2.500
2.000
2.500
3.125
.925
1.177
1.680
2.181
1.539
2.043
2.668
.516
.767
1.269
1.772
.996
1.500
2.129
5.022
5.022
5.022
5.022
4.053
4.053
4.053
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.772
1.772
1.772
1.772
1.772
1.772
1.772
.098
.098
.098
.098
.118
.118
.118
.276
.276
.276
.276
.354
.354
.354
.118
.118
.118
.118
.155
.155
.155
Dimensions (inch)
Max. Depth of Cut
Insert Screw
CS350990T
CS350990T
CS350990T
CS350990T
CS501290T
CS501290T
CS501290T
Wrench
zTKY10F
zTKY10F
zTKY10F
zTKY10F
xTKY25T
xTKY25T
xTKY25T
Insert
zOEMX12T3ETR
xREMX12T3EN
zOEMX1705EpR1
xREMX1705pN
* Clamp Torque (lbf-in) : CS350990T=22, CS501290T=66

INSERTS
Work
Material
P
M
K
H
: Stable Cutting
: General Cutting
: Unstable Cutting
Honing :
E : Round S : Chamfer + Round T : Chamfer
Steel
Stainless Steel
Cast Iron
Hardened Materials
Coated Cermet CBN 1
Order Number
MILLING
*
*
OEMX12T3ETR1
12T3ETR5
12T3ESR1
2
12T3EER1-JS
2
12T3ETR1-JS
OEEX1705ETR1
OEMX1705ETR1
1705ESR1
2
1705EER1-JS
2
1705ETR1-JS
REMX12T3EN
12T3SN
2
12T3EN-JS
REMX1705EN
1705SN
2
1705EN-JS
*2Breaker *
JS
*
*
*2
*
*
JS Breaker
1 Flat insert.
2 Insert with breaker.
K108
M
M
M
M
M
E
M
M
M
M
M
M
M
M
M
M
T
T
S
E
T
T
T
S
E
T
E
S
E
E
S
E
a a a
a a
a
s
a
s s
a
a
a s
a
a
a
s
a
a
s
a

<10 inserts in one case> <1 insert in one case for CBN>
Dimensions (inch)
Class
Honing
F7010
F7030
VP15TF
NX2525
NX4545
MB835
MB730
Shape
D1
S1
F1
.500
.500
.500
.500
.500
.669
.669
.669
.669
.669
.510
.510
.510
.679
.679
.679
.156
.156
.156
.156
.156
.197
.197
.197
.197
.197
.164
.164
.164
.205
.205
.205
.039
.197
.039
.039
.039
.055
.055
.055
.055
.055

Geometry
2
JS Breaker
1
CBN
2
JS Breaker
Fig.1
Fig.2
Fig.3
Fig.4
Set Bolt
y ARBOR TYPE
Dimensions (inch)
D1
D6
D3
L1
D9
L7
D8
W1
L8
Mass
(lbs)
Max. Depth of Cut

A1
ap
A2
Type
(Fig.)
1.250
.925
.516 2.598
.098
.276
.118
1503X
1.500 1.177
.767 1.575
.750
.748
.313
.187
.5
.098
.276
.118
0203
2.000 1.680 1.269 1.575
.750
.748
.415
.313
.201
.8
.098
.276
.118
2504
2.500 2.181 1.772 1.969
.750
.748
.415
.313
.201
1.3
.098
.276
.118
0305C
3.000 2.682 2.271 1.969 1.000 1.024
.512
.375
.236
2.4
.098
.276
.118
BOER2503A
2.480 2.024 1.480 1.969
.748
.415
.313
.187
1.3
.118
.354
.155
0304C
3.150 2.693 2.154 1.969 1.000 1.024
.512
.375
.219
3.8
.118
.354
.155
0405E
3.937 3.484 2.941 2.480 1.500 1.181
.787
.625
.375
6.3
.118
.354
.155
0506E
4.921 4.469 3.929 2.480 1.500 1.380 2.362
.625
.375
7.0
.118
.354
.155
0608F
6.300 5.846 5.307 2.480 2.000 1.496 3.185
.750
.437
11.4
.118
.354
.155
0809F
8.000 7.547 7.003 2.500 2.000 1.496 2.185
.750
.437
16.2
.118
.354
.155
BOE4R202
.750
OEMX12T3pppp
Insert
REMX12T3pppp
Stock Number
R of Teeth
OEMX1705pppp
REMX1705pppp
Order Number
SPARE PARTS
Milling Cutter No.

Insert Screw
Wrench
Set Bolt

zHDSU37513
CS350990T
zTKY10F
MILLING
BOE4R202
1503
0203
2504
0305C
BOER2503A
xBOE4S06U

CS501290T
xTKY25T
BOER0809F
* Clamp Torque (lbf-in) : CS350990T=22, CS501290T=66
SPARE PARTS
M001
TECHNICAL DATA
N001
K109
MILLING
(Ramp milling)
(Face milling)
4 corners usable
(Drilling)
(Boring)
.157inch(Max.)
.354inch(Max.)
(Chamfer milling)
.118inch(Max.)
(Face milling)
8 corners usable
(Helical milling) (Contour milling)
(Shoulder milling)
(Note) These are recommended cutting conditions when cutter diameter is less than 3.15inch. For cutters with diameter > &3.15inch increase cutting speed by 10%.
Above sizes are for OEMX1705 pppp.
Work Material
Hardness
P
Mild Steel
< 180HB
180 280HB
Carbon Steel
Alloy Steel
280 380HB
Pre-Hardened Steel
High Alloy Steel
35 45HRC
< 300HB
M
Stainless Steel
< 270HB
Grade
Cutting Speed
(SFM)
F7010
785 (590 985)
F7030
705 (475 820)
VP15TF
590 (330 820)
F7010
655 (460 785)
F7030
590 (390 690)
VP15TF
590 (330 820)
F7010
490 (330 555)
F7030
425 (295 525)
VP15TF
390 (260 525)
F7010
425 (295 525)
F7030
360 (260 460)
VP15TF
390 (260 525)
F7010
490 (330 555)
F7030
425 (295 525)
VP15TF
390 (260 525)
F7010
655 (460 785)
F7030
590 (390 690)
VP15TF
490 (330 655)
VP15TF
525 (330 720)
MB730
4920 (3280 9840)
MILLING
Cast Iron
Tensile Strength
< 350MPa
Tensile Strength
360 500MPa
VP15TF
525 (330 720)
Tensile Strength
500 800MPa
VP15TF
460 (295 620)
VP15TF
260 (165 330)
MB835
490 (330 655)
Ductile Cast Iron
H
Heat-Treated Steel
45 60HRC
Cutting Mode
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
B (Depth of Cut .004 .020inch)
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
B (Depth of Cut .004 .012inch)
Feed per Tooth

(inch/tooth)
.008 (.006 .010)
.008 (.006 .010)
.008 (.006 .010)
.003 (.002 .004)
.008 (.006 .010)
.008 (.006 .010)
.008 (.006 .010)
.003 (.002 .004)
.008 (.006 .010)
.008 (.006 .010)
.008 (.006 .010)
.003 (.002 .004)
.006 (.004 .008)
.006 (.004 .008)
.004 (.002 .006)
.002 (.001 .003)
.006 (.004 .008)
.006 (.004 .008)
.004 (.002 .006)
.002 (.001 .003)
.006 (.004 .008)
.006 (.004 .008)
.004 (.002 .006)
.003 (.002 .004)
.012 (.010 .014)
.010 (.008 .012)
.006 (.004 .008)
.003 (.002 .004)
.006 (.004 .008)
.010 (.008 .012)
.008 (.006 .010)
.004 (.002 .006)
.002 (.001 .003)
.010 (.008 .012)
.008 (.006 .010)
.004 (.002 .006)
.002 (.001 .003)
.006 (.004 .008)
.006 (.004 .008)
.004 (.002 .005)
.002 (.001 .002)
.006 (.004 .008)
(Note 1) This list of recommended cutting conditions is for ank wear of .012 inch in 30min. cutting time.
(Note 2) More than 2 inch shank length should be clamped in the milling chuck.
(Note 3) Use peck feed when drilling. (.020inch step is recommended)
(Note 4) When chattering occurs, reduce cutting speed to 70 80%.
(Note 5) When using round inserts, make sure that the at portion of the ank surface is secure against the insert seat wall.
K110
APPLICATION
R Corner Milling
Pocket Milling
Core
(Max.)
Face Milling
Minimum Width to
Eliminate Core
Drilling
Core
Deep Shoulder Milling

Approx. .004"
(Wall Face Geometry)
Approx. .047"
Contouring
(Max.)
Max. Depth of Cut
Maximum cutting depth is

.155" by inside cutting edge.
(Max.)
Chamfer Milling
MILLING
Above sizes are for OEMX1705pppp.
K111
MILLING
MULTI FUNCTIONAL
MILLING
BSP
Light Alloy
Including
Flat faces
Roughing
(Max. Depth of Cut)
Cast Iron
(Max. Depth of Cut)
a Multi-function endmill for plunging,
contouring and chamfer milling.

D1
D2
.375
.980 4.053 1.250 1.772
.750 1.345 4.053 1.250 1.772
.276
.197
CS451190T
TKY20F
3 1.500 2.097 4.053 1.250 1.772
.276
.197
CS451190T
TKY20F
Stock
Number of Teeth
Order Number
BSPR061W20
122W20
243W20
Max. Depth of Cut

Dimensions (inch)
L1
D4
L2
Outer
Inner
ap
A2
Insert Screw
Wrench
.276
.079
CS451190T
TKY20F
Insert
SPMB1204APp

INSERTS
Dimensions (inch)
SPMB1204APT
UTi20T
Order Number
Class
Honing
UP20M
Coated Carbide
Shape
D1
M T
.500
Geometry
S1
F1
.187
.055
Ramp milling
(Max.)
(Max.)
Chamfer milling
A
BD
C
Cutting Speed Feed per tooth Cutting Speed Feed per tooth Cutting Speed Feed per tooth
(SFM)
(inch/tooth)
(SFM)
(inch/tooth)
(SFM)
(inch/tooth)
Work Material
Hardness
Grade
Mild Steel
Carbon Steel
Alloy Steel
M Stainless Steel
Cast Iron
K
Gray Cast Iron
Ductile Iron
< 160HB
UTi20T/UP20M
500
.012 .015
500
.008 .012
400
.001 .003
< 230HB
UTi20T/UP20M
500
.008 .012
500
.006 .010
400
.001 .003
< 45HRC
UTi20T/UP20M
200
.004 .010
200
.002 .004
200
.001 .002
< 200HB
UTi20T/UP20M
500
.004 .008
500
.004 .006
400
.001 .003
< 140HB
UTi20T/UP20M
400
.008 .012
400
.004 .012
400
.001 .004
K112
Drilling
Face milling
(Max.)
(Max.)
(Max.)
MILLING

MULTI FUNCTIONAL
MILLING
Roughing
ECMP
a Unique insert seat position
(Max. Depth of Cut)
facilitates smooth initial cutting

and stable machining.
a Excellent chip disposal.
a 86rhombic shape 11positive insert.
Order Number
Stock Number
of Teeth
R
ECMPR162W16
202W20
242W20
a
a
a
2
2
2
Dimensions (inch)
D1
L1
D4
L2
Max.
Depth
of Cut
ap
Insert Screw
Wrench
Insert
TS4
TKY15R
MPMM322
TS5
TKY25R
MPMM432
TS5
TKY25R
MPMM432
1.000 4.500 1.000 1.250 .315

1.250 5.000 1.250 1.750 .433
1.500 6.562 1.250 3.313 .433

INSERTS
UTi20T
Shape
Dimensions (inch)
Class
VP15TF
Coated Carbide
D1
S1
Re
.375
.125
.031
.500
.1875 .031
Order Number
ISO Number
MPMM322
MPMT090308
432
120408
Geometry
(Note) Feed per Tooth (inch/tooth) or Feed per Revolution (inch/rev)
Work Material
Mild Steel
Grade
< 180HB
UTi20T
.004 .010
.004 .008
.004 .006
.004 .006
.004 .006
UTi20T
.004 .008
.004 .006
.002 .004
.002 .004
.003 .005
UTi20T
.004 .012
.004 .010
.004 .008
.004 .006
.004 .006
Carbon Steel Alloy Steel 280350HB
K
Cast Iron
Edge Machining (inch/rev)

Outer Peripheral Edge Cutting (inch/tooth) Cutting Speed : 260400 SFM Bottom Cutting
(Drilling, Boring)
Depth of Cut .080" Depth of Cut .160" Depth of Cut .240" Depth of Cut .320"
Hardness
Tensile
Strength
< 450MPa
MILLING
y ECMPR162W16
y ECMPR202W20, ECMP242W20
Work Material
Mild Steel
Hardness
Grade
Edge Machining (inch/rev)

Outer Peripheral Edge Cutting (inch/tooth) Cutting Speed : 260400 SFM Bottom Cutting
(Drilling, Boring)
Depth of Cut .080" Depth of Cut .160" Depth of Cut .240" Depth of Cut .320" Depth of Cut .400"
< 180HB
UTi20T
.004 .012 .004 .010 .004 .008 .004 .006 .004 .006
.005 .006
UTi20T
.004 .010 .004 .008 .004 .006 .002 .006 .002 .004
.004 .006
UTi20T
.004 .016 .004 .012 .004 .010 .004 .008 .004 .008
.004 .008
Carbon Steel Alloy Steel 280350HB
K
Cast Iron
Tensile
Strength
< 450MPa
y PRECAUTIONS IN USING ECMP

1. Higher than recommended data may be used if depth of cut is small and peripheral cutting is operation.
2. When bottom cutting use coolant.
SPARE PARTS
M001
TECHNICAL DATA
N001
K113
MILLING
CHAMFER
MILLING
CFSP
Light Alloy
Cast Iron
Roughing
(Max. Depth of Cut)
a Excellent sharpness with
11positive inserts.
a 45chamfer series.
Stock
Number of Teeth
Order Number
CFSPR051W16
101W16
203W20
a
a
a
1
1
3
D1
D2
L1
D4
L2
Max.
Depth
of Cut
ap
.313
.625
1.250
.964
1.280
1.905
4.000
4.000
4.125
1.000
1.000
1.250
1.719
1.719
1.844
.327
.327
.327
Dimensions (inch)
*
Insert Screw
Wrench
Insert
TS52
TKY25R
SPMA42p
TS5
TKY25R
SPMA42p
TS5
TKY25R
SPMA42p

INSERTS
Steel
: Stable Cutting
Stainless Steel
: General Cutting
: Unstable Cutting
Cast Iron
ISO Number
SPMW421
SPMW120304
422
120308
a a
Dimensions (inch)
NX2525
NX4545
UTi20T
HTi10
Order Number
Class
MILLING
Shape
P
M
K
VP15TF
UP20M
Work
Material
D1
S1
Re
a a
s s a a
.500
.125
.016
s s a a
.500
.125
.031
Geometry

Work Material
Hardness
P
Carbon Steel
Alloy Steel
180 280HB
280 350HB
K
Cast Iron
K114
Tensile Strength
< 450MPa

Chamfer Milling
Face Milling
Grade
Cutting Speed
(SFM)
UTi20T
590 (425 720)
.016
.006
UP20M
590 (425 720)
.016
.008
NX2525
590 (425 720)
.016
.008
UTi20T
330 (230 395)
.012
.006
UTi20T
460 (330 560)
.020
.004
HTi10
460 (330 560)
.020
.004

BALL NOSE
END MILL
SRF
Light Alloy
Cast Iron
Including
curved faces
Finishing
Fig. 2
Carbon Steel
Alloy Steel Stainless Steel Hardened Steel
Fig. 3
Fig. 4
Fig. 5
Fig. 1

Refer to page K121 for ap &Re.
Inserts
R
D1
D4
L1
D5
L2
L3
L5
B 2
B5
Long
Standard
Clamp
Screw
Wrench Anti-seize
Lubricant
z
RS3008TS
MK1KS
TKY08D
z
RS3510T
MK1KS
TKY10D
x
RS4015T
MK1KS
TKY15T
x
RS5020T TKY20T MK1KS
SRFT0375 .1875 .375

230' 130' 1
.500 4.375 .354 1.625 512 1.535
SRFT10
.1969 .394
208' 130' 1
SRFT0500 .2500 .500
203' 130' 1
.625 4.750 .453 2.000 .591 1.902
08S10M a
SRFT12
.2362 .472
229' 130' 1
SRFT0625 .3125 .625
207' 130' 1
.750 5.125 .606 2.000 .787 1.909
10S12M a
SRFT16
.3150 .630
202' 130' 1
SRFT0750 .3750 .750
252' 130' 1
.3937 .787 1.000 6.000 .732 2.875 .945 2.740 227' 130' 1
12S16M a SRFT20
SUFT20Rpp
.787
227' 130' 2
SRFT1000 .5000 1.000
236' 130' 1
.4921 .984 1.250 7.125 .965 3.250 1.181 3.112 246' 130' 1 RS6025T
16S20M a SRFT25
SUFT25Rpp
.984
246' 130' 2
SRFT1250 .6250 1.250
8.039
3
4.164 1.417
SRFT30
.5906 1.181
8.000
4.125 1.378
3

1.250
1.161

RS8030T
20S20M a
SRFT32
.6299 1.260
8.039
4.164 1.417
3
SUFT30Rpp 1.181
8.000
4.125 1.378
4
SRFT0375 .1875 .375
1
133'
130'
a
RS3008TS
.500 6.000 .354 2.500 .512 2.465
SRFU06S08L
SRFT10
.1969 .394
130' 130' 1
SRFT0500 .2500 .500
130' 130' 1
a
RS3510T
.625 6.375 .453 2.875 .591 2.817
08S10L
SRFT12
.2362 .472
139' 130' 1
SRFT0625 .3125 .625
130' 130' 5
a
RS4015T
.750 7.125 .606 3.625 .787 2.488
10S12L
SRFT16
.3150 .630
130' 130' 5
SRFT0750 .3750 .750
141' 130' 1
a SRFT20
.3937 .787 1.000 8.500 .732 4.625 .945 4.539 130' 130' 1 RS5020T
12S16L
SUFT20Rpp
.787
130' 130' 2
SRFT1000 .5000 1.000
130' 130' 1
a SRFT25
.4921 .984 1.250 9.625 .965 5.750 1.181 5.697 130' 130' 1 RS6025T
16S20L
SUFT25pp
.984
130' 130' 2
SRFT1250 .6250 1.250
10.539
3
6.664 1.417
SRFT30
.5906 1.181
10.500
6.625 1.378
3
a
1.250
1.161

RS8030T
20S20L

SRFT32
.6299 1.260
10.539
6.664 1.417
3
SUFT30pp 1.181
10.500
6.625 1.378
4
(Note) Fit inserts in the right direction. (Refer to page K122 & K123)
Clamp Torque (lbf-in) : RS3008TS=13, RS3510T=22, RS4015T=29, RS5020T=44, RS6025T=66, RS8030T=88
SRFU06S08M
x
MK1KS
TKY25T
MILLING
Dimensions (inch)
Fig.
Order Number
Stock
Type
y Steel Shank
x
MK1KS
TKY30T
z
MK1KS
TKY08D
z
MK1KS
TKY10D
x
MK1KS
TKY15T
x
MK1KS
TKY20T
x
MK1KS
TKY25T
x
MK1KS
TKY30T
SPARE PARTS
M001
TECHNICAL DATA
N001
K115
MILLING
Fig. 1
Fig. 2

Inserts
Long
MILLING
Standard
SRFU06S06MW
08S08MW
10S10MW
12S12MW
16S16MW
20S20MW
SRFU06S06LW
08S08LW
10S10LW
12S12LW
16S16LW
20S20LW
Dimensions (inch)
SRFT0375
SRFT10
SRFT0500
SRFT12
SRFT0625
SRFT16
SRFT0750
SRFT20
SUFT20Rpp
SRFT1000
SRFT25
SUFT25Rpp
SRFT1250
SRFT30
SRFT32
SUFT30Rpp
SRFT0375
SRFT10
SRFT0500
SRFT12
SRFT0625
SRFT16
SRFT0750
SRFT20
SUFT20Rpp
SRFT1000
SRFT25
SUFT25Rpp
SRFT1250
SRFT30
SRFT32
SUFT30Rpp
D1
.1875
.1969
.2500
.2362
.3125
.3150
.3750
.3937

.5000
.4921

.6250
.5906
.6299

.1875
.1969
.2500
.2362
.3125
.3150
.3750
.3937

.5000
.4921

.6250
.5906
.6299
.375
.394
.500
.472
.625
.630
.750
.787
.787
1.000
.984
.984
1.250
1.181
1.260
1.181
.375
.394
.500
.472
.625
.630
.750
.787
.787
1.000
.984
.984
1.250
1.181
1.260
1.181
D4
L1
D5
.375
4.375
.354
1.625 0.512
.500
4.750
.453
2.000 0.591
.625
5.250
.606
2.125 0.787
.750
7.125
.732
4.000 0.945
1.000
8.000
.965
4.125 1.181
1.250
9.039
9.000
1.161
9.039
9.000
5.164
5.125
5.164
5.125
1.417
1.378
1.417
1.378
.375
6.625
.354
3.125
.512
.500
6.625
.453
3.125
.591
.625
8.000
.606
4.500
.787
.750 10.000
.732
6.125
.945
1.000 12.000
.965
8.125 1.181
L2
Clamp Screw
L3
14.039
10.164 1.417
14.000
10.125 1.378
1.250
1.161
14.039
10.164 1.417
14.000
10.125 1.378
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
2
a
r
K116

Wrench
Anti-seize
Lubricant
RS3008TS zTKY08D
MK1KS
RS3510T
zTKY10D
MK1KS
RS4015T
xTKY15T
MK1KS
RS5020T
xTKY20T
MK1KS
RS6025T
xTKY25T
MK1KS
RS8030T
xTKY30T
MK1KS
RS3008TS zTKY08D MK1KS

RS3510T
zTKY10D MK1KS
RS4015T
xTKY15T
MK1KS
RS5020T
xTKY20T
MK1KS
RS6025T
xTKY25T
MK1KS
RS8030T
xTKY30T
MK1KS
(Note) Fit inserts in the right direction. (Refer to page K122 & K123)
Clamp Torque (lbf-in) : RS3008TS=13, RS3510T=22, RS4015T=29, RS5020T=44, RS6025T=66, RS8030T=88
Fig.
Order Number
Stock
Type
y Carbide Shank
Fig. 3
Fig. 4
Fig. 5
Fig. 1
Fig. 6
Fig. 2
METRIC Standard
Standard
Semi Long
20S25M
25S32M
30S32M
32S32M
SRFH10S12L
12S16L
16S20L
s
s
s
s
s
20S25L
20S20L80
25S32L
25S25L100
30S32L
SRFT10
SRFT12
SRFT16
SRFT20
SUFT20Rpp
SRFT25
SUFT25Rpp
SRFT30
SUFT30Rpp
SRFT32
SRFT10
SRFT12
SRFT16
SRFT20
SUFT20Rpp
SRFT20
SUFT20Rpp
SRFT25
SUFT25Rpp
SRFT25
SUFT25Rpp
SRFT30
SUFT30Rpp
D1
D4
L1
D5
L2
L3
L5
B 2
B5
5
6
8
10

12.5

15

16
5
6
8
10

10

12.5

12.5

15
10
12
16
20
20
25
25
30
30
32
10
12
16
20
20
20
20
25
25
25
25
30
30
12
16
20
25
25
32
32
32
32
32
12
16
20
25
25
20
20
32
32
25
25
32
32
110
120
130
150
150
180
180
200
200
200
150
160
160
180
180
180
180
200
200
200
200
230
230
9.5
11.5
15.5
19.5
19.5
24.5
24.5
29.5
29.5
31.5
9.5
11.5
15.5
19.5
19.5
19.5
19.5
24.5
24.5
24.5
24.5
29.5
29.5
40
50
50
70
70
80
80
100
100
100
60
70
70
80
80
80
80
100
100
100
100
130
130
13
15
20
24
24
30
30
35
35
35
13
15
20
24
24
24
24
30
30
30
30
35
35
39.1
47.9
47.9
67.5
67.5
76.6
76.6

39.3
68.5
68.4
77.7
77.7

97.2
97.2

138
236
244
223
223
258
258

130
147
151
203
203

217
217

130
130
130
130
130
130
130

130
130
130
130
130

130
130

1
1
1
1
2
1
2
3
4
3
5
1
1
1
2
3
4
1
2
3
4
3
4
Clamp
Screw
RS3008T
RS3510T
RS4015T
Wrench Anti-seize
Lubricant
zTKY08D MK1KS
zTKY10D MK1KS
xTKY15T MK1KS
RS5020T xTKY20T MK1KS

MILLING
Inserts
SRFH10S12M
12S16M
16S20M
Dimensions (mm)
Fig.
Order Number
Stock
Type
y Steel Shank

RS8030T
RS3008T
RS3510T
RS4015T
xTKY30T
zTKY08D
zTKY10D
xTKY15T
MK1KS
MK1KS
MK1KS
MK1KS

(Note 1) Fit inserts in the right direction. (Refer to page K122 & K123)
(Note 2) Inch type insert can not be installed on the metric holder.
Clamp Torque (lbf-in) : RS3008T=13, RS3510T=22, RS4015T=29, RS5020T=44, RS6025T=66, RS8030T=88
SPARE PARTS
M001
TECHNICAL DATA
N001
K117
Inserts
Extra Long
Long
SRFH20S25E
20S20E120
25S32E
25S25E150
30S32E
SRFH20S25X
25S32X
30S32X
32S32X
Dimensions (mm)
SRFT20
SUFT20Rpp
SRFT20
SUFT20Rpp
SRFT25
SUFT25Rpp
SRFT25
SUFT25Rpp
SRFT30
SUFT30Rpp
SRFT20
SUFT20Rpp
SRFT25
SUFT25Rpp
SRFT30
SUFT30Rpp
SRFT32
D1
D4
10
20
25 220 19.5 120 24
82.4 130
130
20
25 220 19.5 120 24
82.4 130
130
10
20
20 220 19.5 120 24
20
20 220 19.5 120 24
25
12.5 25
D5
L2
L3
L5
B2
Clamp
Screw
12.5 25
L1
B5
32 250 24.5 150 30 125.5 130

130
32 250 24.5 150 30 125.5 130

130
25 250 24.5 150 30
25
25 250 24.5 150 30
15
30
32 300 29.5 200 35
30
32 300 29.5 200 35
10
20
25 250 19.5 150 24
82.4 130
130
20
25 250 19.5 150 24
82.4 130
130
12.5 25
MILLING
K118
32 300 24.5 200 30 123.1 130

130
25
32 300 24.5 200 30 123.1 130

130
15
30
32 350 29.5 250 35
30
32 350 29.5 250 35
16
32
32 350 31.5 250 35
Wrench Anti-seize
Lubricant

Fig.
Order Number
Stock
Type
MILLING
Fig. 1
Fig. 2
METRIC Standard
Standard
D1
D4
L1
D5
L2
Clamp Screw
L3
Wrench
Anti-seize
Lubricant
SRFH10S10MW
SRFT10
10
10
110
9.5
40
13
RS3008T zTKY08D MK1KS
12S12MW
SRFT12
12
12
120
11.5
50
15
16S16MW
SRFT16
16
16
130
15.5
50
20
SRFT20
10
20
20
180
19.5
80
24
20
20
180
19.5
80
24
12.5
25
25
200
24.5
100
30
25
25
200
24.5
100
30
SRFT30
15
30
32
230
29.5
130
35
SRFT32
16
32
32
231
29.5
131
36
20S20MW
25S25MW
30S32MW
SUFT20Rpp
SRFT25
SUFT25Rpp

SUFT30Rpp
32
32
230
29.5
130
35
SRFH10S10LW
SRFT10
10
10
150
9.5
60
13
12S12LW
SRFT12
12
12
160
11.5
70
15
16S16LW
SRFT16
16
16
160
15.5
70
20
16S16EW
SRFT16
16
16
200
15.5
110
20
SRFT20
10
20
20
250
19.5
150
24
20
20
250
19.5
150
24
12.5
25
25
300
24.5
200
30
25
25
300
24.5
200
30
SRFT30
15
30
32
350
29.5
250
35
SRFT32
16
32
32
351
29.5
251
36
30
32
350
29.5
250
35
20S20LW
25S25LW
30S32LW
SUFT20Rpp
SRFT25
SUFT25Rpp
SUFT30Rpp
MILLING
Inserts
Long
Dimensions (mm)
Fig.
Order Number
Stock
Type
y Carbide Shank
SPARE PARTS
M001
TECHNICAL DATA
N001
K119
MILLING
L2
H1
L11
Re
SECTION A-A
L1
D4
D5
D1
D4
D5
D1
ap (Max. Depth of Cut) A

L2
L1
H1
L11
SECTION A-A
METRIC Standard
y Screw-in Type
20AM1035
25AM1240
30AM1645
Dimensions (mm)
Insert
R
D1
D4
D5
L1
L2
L11
Anti-seize
Lubricant
TKY15T
MK1KS
0.1 RS5020T
TKY20T
MK1KS
0.1 RS6025T
TKY25T
MK1KS
TKY30T
MK1KS
16
8.5 14.9
48
30
10
SRFT20
10
20
10.5 18.4
54
35
14
M10
20
10.5 18.4
54
35
14
M10
12.5
25
12.5 23.5
62
40
19
M12
25
12.5 25.5
62
40
19
M12
SRFT30
15
30
17
28.1
68
45
24
M16 0.2
SRFT32
16
32
17
28.1
69
46
24
M16
32
17
28.1
69
46
24
M16
SUFT20Rpp
SRFT25
SUFT25Rpp
Clamp Torque (lbf-in) : RS4015T=29, RS5020T=44, RS6025T=66, RS8030T=88
MILLING

*
Wrench
SRFT16
SUFT30Rpp
K120
H1
Mass (kg)
Coolant Hole
SRFH16AM0830
Stock
Order Number
Clamp
Screw
M8 0.1 RS4015T
0.2
RS8030T
INSERTS
INCH Standard
Dimensions (inch)
D1
SRFT0375
a a
.375
.1875
.335
.020
.102
0500
a a
.500
.2500
.394
.020
.118
0625
a a
.625
.3125
.472
.039
.158
0750
a a
.750
.3750
.591
.039
.197
1000
a a
1.000
.5000
.728
.039
.236
1250
a a
1.250
.6250
.925
.039
.276
Re
L1
F1
S1
ap
Geometry
F1
L1.0006"
R .00024"
S1
Order Number
. 0
00
11
"
Shape
MP8010
VP15TF
Coated
METRIC Standard
Dimensions (mm)
s s
10
5 (.1969")
0.5
2.6
12
s s
12
6 (.2362")
10
0.5
16
s s
16
8 (.3150")
12
20
s s
20
10 (.3937")
15
25
s s
25
12.5 (.4921")
18.5
30
s s
30
15 (.5906")
22.5
32
s s
32
16 (.6299")
23.5
S1
ap
Geometry
F1
L10.015
8.5
F1
R 0.006
S1
L1
0 0
.0
27
Re
D
s
20
0.5 (.0197")
15
2.5
20R10
20
1 (.0394")
15
20R20
20
2 (.0787")
15
20R30
20
3 (.1181")
15
25R05
25
0.5 (.0197")
18.5
2.5
25R10
25
1 (.0394")
18.5
2.5
3.5
25R20
25
2 (.0787")
18.5
2.5
4.5
25R30
25
3 (.1181")
18.5
2.5
5.5
30R05
30
0.5 (.0197")
22.5
3.5
30R10
30
1 (.0394")
22.5
30R20
30
2 (.0787")
22.5
30R30
30
3 (.1181")
22.5
F1
ap
SUFT20R05
MILLING
SRFT10
L10.015
D1
Order Number
S1
Re0.010
0 0
.0
20
Shape
MP8010
VP15TF
Coated
SCREW-IN ARBORS
K142
SPARE PARTS
M001
TECHNICAL DATA
N001
K121
MILLING
Recommended Cutting Conditions for SRFT Ball-nose inserts
Hardness
Insert Grades
Cutting Speed
vc
Feed per Tooth

fz
Depth of Cut
ap
(SFM)
(IPT)
(inch)
Carbon Steel
Alloy Steel
180 280HB
VP15TF
655 (260 985)
.008 (.004 .012)
< 0.05D1
Pre-hardened steels
< 45HRC
VP15TF
490 (260 655)
.008 (.004 .012)
< 0.05D1
Alloy Tool Steel
180 380HB
VP15TF
490 (260 655)
.008 (.004 .012)
< 0.05D1
Cast Iron
Tensile Strength
< 350MPa
MP8010
820 (590 1475)
.008 (.004 .012)
< 0.05D1
Ductile Cast Iron
Tensile Strength
< 800MPa
MP8010
655 (260 985)
.008 (.004 .012)
< 0.05D1
45 55HRC
MP8010
330 (195 395)
.008 (.004 .012)
< 0.05D1
>55HRC
MP8010
260 (195 395)
.008 (.004 .012)
< 0.01D1
Work Material
H
Hardened Steel
(Note 1) The values above are for average machining conditions. The optimum values can change slightly according to the condition
and rigidity of the machine and work holding. Adjust the values accordingly.
(Note 2) For end mills with a carbide shank, up to 20 percent higher cutting conditions are possible.
(Note 3) Please note the following when machining hardened steel with MP8010.
Please shorten the overhang length as much as possible.
Use with carbide shank recommended.
Take special care with the depth of cut to prevent fracture.
Calculating Actual Cutting Speed

1. Effective cutting diameter = 2 ap (D1-ap)
D1
D1 : Tool diameter (inch)

ap : Depth of Cut (inch)
2. Using ap
Calculate cutting speed at the depth of cut line.
ap
vc =
MILLING
vc : Actual cutting speed (SFM)

n : Revolution (min-1)
Effective
cutting diameter
Selecting Pick Feed

Theoretical
h=
h : Cusp height
pf : Pick feed
R : Ball nose or corner radius
Actual surface roughness Rz will be about 3 times worse than theoretical h.

This is because of the effect of a built-up edge.
To determine Pf, use the formula below based on a particular Rz value.
Pf =
Pf
Insert Installation
1. Clean the insert and the insert pocket
Thoroughly clean the insert and the insert pocket on the holder body.
2. Fitting the insert

Place the concave mark on the insert uppermost as shown with the clamp screw
inserted from above. Fasten the clamp screw while firmly pressing the insert
against the insert pocket wall. Use of a special anti seize lubricant MK1KS is
recommended. Tighten at the recommended torque range.
K122
Concave mark
GROOVING SYSTEM
Recommended Cutting Conditions for SUFT Corner Radius insert
y Shoulder milling(When small width of cut.*)
Hardness
Insert Grades
Cutting Speed
vc
Depth of Cut
ap
Wide of Cut
ae
Feed per Tooth

fz
(SFM)
(mm)
(mm)
(IPT)
Carbon Steel
Alloy Steel
180 280HB
VP15TF
655 (260 985)
< 0.05D1
< 0.05D1
.008 (< .016)
Pre-hardened steels
< 45HRC
VP15TF
490 (260 655)
< 0.05D1
< 0.05D1
.006 (< .012)
Alloy Tool Steel
180 380HB
VP15TF
490 (260 655)
< 0.05D1
< 0.05D1
.006 (< .012)
Cast Iron
Tensile Strength
< 350MPa
VP15TF
655 (260 985)
< 0.05D1
< 0.1D1
.012 (< .016)
Ductile Cast Iron
Tensile Strength
< 800MPa
VP15TF
490 (260 655)
< 0.05D1
< 0.1D1
.012 (< .016)
Hardened Steel
45 55HRC
VP15TF
260 (195 330)
< 0.05D1
< 0.02D1
.004 (< .006)
Wide of Cut
ae
Feed per Tooth

fz
Work Material
Work Material
Hardness
Insert Grades
Cutting Speed
vc
Depth of Cut
ap
(SFM)
(mm)
(mm)
(IPT)
Carbon Steel
Alloy Steel
180 280HB
VP15TF
655 (260 985)
< 0.02D1
< D1
.008 (< .016)
Pre-hardened steels
< 45HRC
VP15TF
490 (260 655)
< 0.02D1
< D1
.006 (< .012)
Alloy Tool Steel
180 380HB
VP15TF
490 (260 655)
< 0.02D1
< D1
.006 (< .012)
Cast Iron
Tensile Strength
< 350MPa
VP15TF
655 (260 985)
< 0.03D1
< D1
.012 (< .016)
Ductile Cast Iron
Tensile Strength
< 800MPa
VP15TF
490 (260 655)
< 0.03D1
< D1
.012 (< .016)
Hardened Steel
45 55HRC
VP15TF
260 (195 330)
< 0.01D1
< D1
.004 (< .006)
When the pick feed direction is along the radius of the tool such as nish face machining.
*(Note
1)This cutting condition is the standard condition when using the steel standard shank type.
If it is occurred vibration or chipping on the cutting edge, please decrease the cutting condition as width of cut, depth of cut
and feed per tooth depending on the situation.
(Note 2)The value of cutting speed is stood at the peripheral diameter of the tool.
Please calculate the spindle speed of tool in the following expressions.
Spindle speed of cutting tool n(min-1 )=12Cutting speed vc Diameter of cutting tool D1 3.14
MILLING
* When the pick feed direction is along the axis of the tool such as nish machining at the wall part.
y Slot milling / Shoulder milling(When large width of cut.*)
Insert Installation
1. Clean the insert and insert pocket
Thoroughly clean the insert and the insert pocket on the holder body.
2. Fitting the insert
Concave mark
Place the concave mark on the insert uppermost as shown with the clamp screw
inserted from above. Fasten the clamp screw while firmly pressing the insert
against the insert pocket wall. Use of a special anti seize lubricant MK1KS is
recommended. Tighten at the recommended torque range.
K123
MILLING
BALL NOSE
END MILL
Including
curved faces
Finishing
MBN
Order Number
MBN040375SC
040500SB
050625SB
060750SA
081000SA
101250SB
10M300SB
10M300SC
Stock
y STRAIGHT MBN SERIES TOOL HOLDER
a
a
a
a
a
a
a
a
Dimensions (inch)
D1
L1
D4
L2
D5
.375
.500
.625
.750
1.000
1.250
30mm
30mm
3.540
5.910
6.300
8.270
9.060
8.270
6.890
8.270
.500
.500
.625
.750
1.000
1.250
1.250
1.250
1.340
1.810
2.090
2.360
3.140
3.150
2.200
3.150
.335
.413
.551
.709
.882
1.126
1.126
1.126
Insert Screw
BLS03
BLS04
BLS05
BLS06
BLS08
BLS12
BLS12
BLS12
Wrench
TKY15R
TKY20R
TKY20R
TKY20R
TKY30R
TKY30R
TKY30R
TKY30R
Insert
MBN0375
MBN0500
MBN0625
MBN0750
MBN1000
MBN1250
MBNM300
MBNM300
Wrench
TKY08D
TKY15R
TKY20R
TKY20R
TKY20R
TKY30R
TKY30R
Insert
MBN0312
MBN0375
MBN0500
MBN0625
MBN0750
MBN1000
MBN1250
(Note) Uses MBN style inserts only.

Clamp Torque (lbf-in) : BLS03=27, BLS04=35, BLS05=44, BLS06=53, BLS08=58, BLS12=58
Order Number
MILLING
MBN040312TB
040375TB
050500TB
060625TB
080750TB
101000TB
121250TB
Stock
y TAPERED NECK MBN SERIES TOOL HOLDER
a
a
a
a
a
a
a
Dimensions (inch)
D1
L1
D4
L2
D5
.312
.375
.500
.625
.750
1.000
1.250
5.510
5.910
6.300
6.890
7.480
8.270
9.450
.500
.500
.625
.750
1.000
1.250
1.500
1.970
1.380
2.360
2.640
3.150
3.940
4.840
.295
.354
.413
.551
.709
.882
1.167
Insert Screw
BLS02
BLS03
BLS04
BLS05
BLS06
BLS08
BLS12
(Note) Uses MBN style inserts only.

Clamp Torque (lbf-in) : BLS02=18, BLS03=27, BLS04=35, BLS05=44, BLS06=53, BLS08=58, BLS12=58
INSERTS
Shape
K124
Order Number
APL05
D1 (inch)
MBN0312001
0375001
0500001
0625001
0750001
1000001
1250001
M200001
M300001
a
a
.312
.375
.500
.625
.750
1.000
1.250
20mm ( .7874)
30mm (1.181)
a
a
a
a
a
a
a
Geometry
RADIUS
END MILL
Including
curved faces
Finishing
MBD/MBF
Order Number
MBD040500SB
050625SB
060750SB
081000SB
Stock
y STRAIGHT NECK MBD SERIES TOOL HOLDER
a
a
a
a
Dimensions (inch)
D1
L1
D4
L2
D5
.500
.625
.750
1.000
5.980
6.380
6.890
7.480
.500
.625
.750
1.000
1.890
2.160
2.480
2.830
.413
.551
.709
.882
Insert Screw
BLS04
BLS05
BLS06
BLS08
Wrench
TKY20R
TKY20R
TKY20R
TKY30R
Insert
MBD/F 0500
MBD/F 0625
MBD/F 0750
MBD/F 1000
(Note) Uses MBD and MBF style inserts only.

Clamp Torque (lbf-in) : BLS04=35, BLS05=44, BLS06=53, BLS08=58
INSERTS
Order Number
APL05
D1
Re
MBD0500021
.500
.031
.550
0500041
.500
.063
.550
0625021
.625
.031
.625
0625041
.625
.063
.625
0750021
.750
.031
.700
0750041
.750
.063
.700
1000021
1.000
.031
.925
1000041
1.000
.063
.925
1000081
1.000
.125
.925
MBF0500021
.500
.031
.550
0500041
.500
.063
.550
0625021
.625
.031
.625
0625041
.625
.063
.625
0750021
.750
.031
.700
0750041
.750
.063
.700
1000021
1.000
.031
.925
1000041
1.000
.063
.925
1000081
1.000
.125
.925
Geometry
Backdraft
MILLING
Shape
Flat Bottom
SPARE PARTS
M001
TECHNICAL DATA
N001
K125
MILLING
MBD/MBF/MBN
y CALCULATED EFFECTIVE CUTTING DIAMETER FOR BALL NOSE AND FEEDRATE MULTIPLIER
.005
.078 4.000 .086 4.200 .099 4.600
.111 5.000 .122 5.300 .125 5.390
.141 5.800
.153 6.170
.158 6.300
.010
.110 3.100 .121 3.300 .140 3.700 .157 4.000 .172 4.200 .176 4.280
.199 4.600
.216 4.900
.223 5.000
.020
.153 2.500 .169 2.700 .196 2.900 .220 3.100 .242 3.300 .248 3.400
.280 3.700
.304 3.890
.314 4.000
.050
.229 1.800 .255 2.000 .300 2.200 .339 2.300 .374 2.500 .384 2.500
.436 2.700
.475 2.870
.490 2.900
.075
.267 1.600 .300 1.700 .357 1.900 .406 2.000 .450 2.200 .462 2.190
.527 2.400
.576 2.500
.594 2.600
.100
.295 1.500 .332 1.600 .400 1.700 .458 1.800 .510 2.000 .524 1.990
.600 2.200
.657 2.280
.678 2.300
.125
.306 1.400 .354 1.400 .433 1.600 .500 1.700 .559 1.800 .575 1.850
.661 2.000
.727 2.110
.750 2.200
.156
.370 1.300 .463 1.500 .541 1.600 .609 1.700 .627 1.710
.726 1.900
.800 1.960
.826 2.000
.188
.375 1.000 .484 1.400 .573 1.500 .650 1.600 .671 1.610
.781 1.700
.864 1.840
.894 1.900
.250
.500 1.000 .612 1.400 .707 1.400 .733 1.470
.866 1.600
.964 1.680 1.000 1.700
.312
.625 1.000 .739 1.300 .770 1.360
.375
.750 1.000 .787 1.280
.927 1.500 1.042 1.560 1.082 1.600

.968 1.400 1.099 1.470 1.146 1.500
.600
1.000 1.000 1.000 1.000 1.225 1.300
.625
1.250 1.000
Roughness (Rth)
MILLING
MBN insert with chipbreaker, axial depth of cut range .010" to 15% of cutter diameter. Rec. Axial DOC = .020" to .030"
MBN insert without chipbreaker depth of cut range .007" to .050". Rec. Axial = .015" to .030"
Ideal chip thickness = .005" to .008"
Excessive feed can deteriorate surface nish.
WOC
Step over
Effective
Diameter
Rth= D
2
D2 - WOC2
4
D=Tool Diameter
K126
Eff.
Cutting
Dia
Feed Rate
Multiple
Eff.
Cutting
Dia
Feed Rate
Multiple
Eff.
Cutting
Dia
Feed Rate
Multiple
Eff.
Cutting
Dia
Feed Rate
Multiple
Eff.
Cutting
Dia
Feed Rate
Multiple
Eff.
Cutting
Dia
Feed Rate
Multiple
Eff.
Cutting
Dia
Feed Rate
Multiple
Eff.
Cutting
Dia
Feed Rate
Multiple
Feed Rate
Multiple
&.3125" Ball Nose &.375" Ball Nose &.50" Ball Nose &.625" Ball Nose &.750" Ball Nose &20mm Ball Nose &1.0" Ball Nose &30mm Ball Nose &1.25" Ball Nose
Axial
Eff.
DOC Cutting
Dia
MBN and MBD Tool Holder Descriptions
MBN 05 0625 S B
z
z Holder Style
b Length
A = Long, B = Medium and C = Short
MBN = Ball Nose

MBD = Backdraft
x Shank Dia. in 1/8"
c Tool Dia.
0500 = 1/2, 0625 = 5/8
1+1/4 = 1250, and 30.5mm = M305
4 = 1/2, 5 = 5/8
and 1+1/4 = 10
v Shank Style
S = Straight and T = Tapered
MBN, MBD and MBF Insert Descriptions
MBN 0625 00 1
z Insert Type
MBN = Ball Nose

MBD = Backdraft
MBF = Flat Bottom
v Chip Breaker Type
1 = No Breaker
c Insert Corner Radius

x Insert Dia.
MBN = 00
MBD and MBF in 1/64 inc.
0625 = 5/8 and

M305 = 30.5mm
02 = 1/32, 04 = 1/16 etc.
y GRADE DESCRIPTIONS
APL05 A premium micrograin carbide combined with alternating layers of thermally stable TiAlN.
This combination of micrograin carbide and TiAlN enables APL05 to exceed the most demanding high speed
nishing requirements of the Die Mold professional.
Work Material
Plain Carbon Steel

Alloy Steels and
Medium Carbon Tool Steels
Stainless Steels
200 & 300 Series
400 & 500 Series
PH Series
Gray Cast Iron
Ductile and Malleable Cast Iron
Aluminum Low Silicon
High Silicon
Wood and Resins
Graphite
Nickel Base Alloys
Pure Titanium and Titanium Alloys
Hardness
(BHN)
Cutting Speed
(SFM)
50 180
180 330
135 330
330 450
450 500
135 275
135 330
330 425
425 500
150 375
120 320
120 320

140 300
300 475
110 300
300 350
350 440
250 800
250 800
220 650
150 600
400 500
200 700
230 650
180 600
400 500
200 800
300 1000
300 800
800 1000
300 550
1000 2400
800 1500
80 450
50 260
100 1200
50 600
35 300
Feed Rate
(IPT)
.004 .025
.004 .015
.004 .008
.003 .006
.004 .009
.004 .011
.004 .008
.003 .006
.004 .012
.004 .014
.004 .014
.004 .020
.003 .015
.003 .020
.003 .016
.003 .008
.003 .008
.004 .010
.004 .010
.004 .010
MILLING
y RECOMMENDED FINISHING SPEEDS AND FEEDS
K127
MILLING
BALL NOSE
END MILL
Including
curved faces
Roughing
SRM2
Light Alloy
Cast Iron

a Suitable for roughing to semi-nishing of small and
medium molds.
a High rigidity body design.
a Low resistance chipbreaker.
a Key type clamp.
a Shrink t ready.
a Short Type
(Draft Angle)
a Medium Type
SRM210SAS2
SRM212SAS2
SRM210SAM2
SRM212SAM2
SRM216SAS2
SRM220SAS2
SRM216SAM2
SRM220SAM2
a Long Type
(Draft Angle)
(Draft Angle)
a Long Edge Type
SRM210SAL2
SRM212SAL2
SRM216SAL2
SRM212SAL4
SRM216SAL4
SRM220SAL2
SRM220SAL4
(Draft Angle)
Stock
Number of Teeth
Order Number
Short
Long
Long Edge
*
K128
Dimensions (inch)
x
c
Inner, Outer Peripheral Inner, Outer Peripheral

R
R
D1
L1
D4
L2
L3
ap B2 Insert Screw
Wrench
z
TS25H

.75 1.5 1.0
.625 3
SRM210SAS2 a 2 .313 .625 4
TKY08D
z

1
1.5 1.25 .750 6 30' TS32
212SAS2 a 2 .375 .75 4
TKY08D
x

4.5 1
2

.945 TS43
216SAS2 a 2 .500 1
TKY15T
x

1.25 2
1.102 TS55
220SAS2 a 2 .625 1.25 5
TKY25T

.75 2.5 1.0
.625 1 30' TS25H z
SRM210SAM2 a 2 .313 .625 5
TKY08D
z

1
2.5 1.25 .750 1 30' TS32
212SAM2 a 2 .375 .75 5
TKY08D
x

5.5 1
3

.945 TS43
216SAM2 a 2 .500 1
TKY15T
x

1.102 TS55
220SAM2 a 2 .625 1.25 6.5 1.25 3.5
TKY25T

.75 3.5 1.0
.625 1 30' TS25H z
SRM210SAL2 a 2 .313 .625 6
TKY08D
z

1
3.5 1.50 .750 1 30' TS32
212SAL2 a 2 .375 .75 6
TKY08D
x

6.5 1.25 4
1.75 .945 1 30' TS43
216SAL2 a 2 .500 1
TKY15T
x

1.25 5
1.102 TS55
220SAL2 a 2 .625 1.25 8
TKY25T
z
1
3.5 1.50 1.180 1 30' TS32 TS25 z
SRM212SAL4 a 4 .375 .75 6
TKY08D TKY08D
c
6.5 1.25 4
1.75 1.457 1 30' TS43 TS25 x
216SAL4 a 4 .500 1
TKY15T TKY08F
c
1.25 5
1.732 TS55 TS43 x
220SAL4 a 4 .625 1.25 8
TKY25T TKY15F
Clamp Torque (lbf-in) : TS25H=8.9, TS25=8.9, TS32=8.9, TS43=31, TS55=66
Medium
MILLING
Type
y SHANK TYPE
Inner
Outer
Insert
SRM210C-M SRM210E-M
SRM212C
SRM212C-M
SRM216C
SRM216C-M
SRM220C
SRM220C-M
SRM212E
SRM212E-M
SRM216E
SRM216E-M
SRM220E
SRM220E-M
SRM210C-M SRM210E-M
SRM212C
SRM212C-M
SRM216C
SRM216C-M
SRM220C
SRM220C-M
SRM212E
SRM212E-M
SRM216E
SRM216E-M
SRM220E
SRM220E-M
SRM210C-M SRM210E-M
SRM212C
SRM212C-M
SRM216C
SRM216C-M
SRM220C
SRM220C-M
SRM212C
SRM212C-M
SRM216C
SRM216C-M
SRM220C
SRM220C-M
SRM212E
SRM212E-M
SRM216E
SRM216E-M
SRM220E
SRM220E-M
SRM212E
SRM212E-M
SRM216E
SRM216E-M
SRM220E
SRM220E-M
Peripheral

APMT1135
PDER-p2
APMT1135
PDER-p2
APMT1604
PDER-p2
INSERTS
Dimensions (inch)
Order Number
L1
L2
S1
F1
Re
.313
.630 .323
.138
212C-M
.375
.748 .385
.169
216C-M
.500
.945 .512
.216
220C-M
.625 1.102 .638
.275
SRM210E-M
.313
.531 .258
.138
212E-M
.375
.610 .315
.169
216E-M
.500
.807 .409
.216
220E-M
.625
.964 .520
.275
Strong Cutting SRM212C

Edge Type
.375
.748 .385
.169
216C
.500
.945 .512
.216
220C
.625 1.102 .638
.275
SRM212E
.375
.610 .315
.169
216E
.500
.807 .409
.216
220E
.625
.964 .520
.275
Strong Cutting APMT1135PDER-H2

Edge Type
.433 .250
.138
.047
.031
1604PDER-H2
.650 .375
.187
.055
.031
Low Resistance APMT1135PDER-M2

Type
.433 .250
.138
.047
.031
.650 .375
.187
.055
.031
With Breaker
SRM210C-M
Strong Cutting
Edge Type
1604PDER-M2
Geometry
MILLING
Shape
With Breaker
No Breaker
No Breaker
With Breaker
With Breaker
Peripheral
Outer
Inner
Outer
Inner
Type
Class
VP15TF
Coated
(Note) The M type breaker (APMT....PDER-M2) is the rst recommendation for its excellent cutting performance.
Please use H type breakers (APMT....PDER-H2) due to cutting edge strength.
SPARE PARTS
M001
TECHNICAL DATA
N001
K129
MILLING
D4
D1
D5
a Standard Type
R
A
ap (Max.depth of cut)
L2
L11
H1
L1
Section A-A
A
D4
D1
D5
a Long Type
ap (Max.depth of cut)
L2
H1
L11
L1
Section A-A
METRIC Standard
Long
MILLING
Standard
Dimensions (mm)
Wrench
16 8.5 14.6 48 30 6 10 M8 12 0.1 TS25H
zTKY08D
20 10.5 18.6 54 35 6 14 M10 14 0.1 TS32
zTKY08D
TS25
xTKY15T
SRM2160AM08S30
s u
2200AM10S35
s u
10
2250AM12S40
s u
12.5 25 12.5 23.5 62 40 6 19 M12 19 0.2 TS43
2300AM16S45
s u
15
30 17 28.3 68 45 6 24 M16 24 0.2 TS55
2320AM16S45
s u
16
32 17 30.0 68 45 6 24 M16 28 0.2 TS55
TS43
SRM2200AM10L45
s u
10
20 10.5 18.6 64 45 6 14 M10 30 0.2 TS32
TS25
2250AM12L55
s u
12.5 25 12.5 23.5 77 55 6 19 M12 37 0.3 TS43
TS25
2300AM16L60
s u
15
30 17 28.3 83 60 6 24 M16 44 0.3 TS55
TS43
2320AM16L60
s u
16
32 17 29.0 83 60 6 24 M16 44 0.3 TS55
TS43

Inner, Outer Peripheral

*2
R D1 D4 D5 L1 L2 L11 H1 M ap (kg)
Insert Screw
Torque (lbf-in) : TS25H=8.9, TS25=8.9, TS32=8.9, TS43=31, TS55=66

*12 Clamp
Clamp Torque of the Head (lbf-ft) : M8=17.1, M10=33.8, M12=59.2, M16=66.7
*
K130
Mass
Stock
Order Number
Coolant Thru
Type
y SCREW-IN TYPE
xTKY15T
cTKY08F
xTKY25T
cTKY15F
zTKY08D
xTKY15T
cTKY08F
xTKY25T
cTKY15F
xTKY25T
cTKY15F
Inner
SRG16C
SRM16C-M
SRG20C
SRM20C-M
SRG25C
SRM25C-M
SRG30C
SRM30C-M
SRG32C
SRM32C-M
SRG20C
SRM20C-M
SRG25C
SRM25C-M
SRG30C
SRM30C-M
SRG32C
SRM32C-M
Outer
Insert
SRG16E
SRM16E-M
SRG20E
SRM20E-M
SRG25E
SRM25E-M
SRG30E
SRM30E-M
SRG32E
SRM32E-M
SRG20E
SRM20E-M
SRG25E
SRM25E-M
SRG30E
SRM30E-M
SRG32E
SRM32E-M
Peripheral

APMT1135
PDER-p2
APMT1135
PDER-p2
APMT1604
PDER-p2
APMT1604
PDER-p2
For Metric Standard
INSERTS
Dimensions (mm)
Order Number
Strong Cutting
Edge Type
SRG16C
20C
25C
30C
32C
SRG16E
20E
25E
30E
32E
SRM16C-M
20C-M
25C-M
30C-M
32C-M
SRM16E-M
20E-M
25E-M
30E-M
32E-M
APMT1135PDER-H2
1604PDER-H2
G
G
G
G
G
G
G
G
G
G
M
M
M
M
M
M
M
M
M
M
M
M
Low Resistance APMT1135PDER-M2

Type
1604PDER-M2
M
M
Outer
Strong Cutting
Edge Type
Inner
Low Resistance
Type
Outer
Low Resistance
Type
Peripheral
Class
F7030
VP15TF
Shape
Inner
Type
Coated
Strong Cutting
Edge Type
s
s s
s s
s s
s s
s
s s
s s
s s
s s
s
s
s
s
s
s
s
s
s
s
a a
a a
a a
a a
L1
L2
S1
F1
Re
B 3
8
10
12.5
15
16
8
10
12.5
15
16
8
10
12.5
15
16
8
10
12.5
15
16

16
19
24
28
28
13.5
15.5
20.5
25.2
26.1
16
19
24
28
28
13.5
15.5
20.5
25.2
26.1
11
16.5
8.2
10.2
12.8
15.3
16.3
6.7
8.5
10.2
12.2
13.1
8.2
10.2
12.8
15.3
16.3
6.7
8.5
10.2
12.2
13.1
6.35
9.525
3.5
4.6
5.5
7
7
3.5
4.6
5.5
7
7
3.5
4.6
5.5
7
7
3.5
4.6
5.5
7
7
3.5
4.76

1.2
1.4

0.8
0.8
11
10
10
10
10
11
9
9
9
9
11
10
10
10
10
11
9
9
9
9
11
11

11
16.5
6.35
9.525
3.5
4.76
1.2
1.4
0.8
0.8
11
11
Geometry
18
18
(Low-resistance inner or outer inserts are precision M class type.)

Selection guide for peripheral cutting edges : The rst recommendation is the super sharp M breaker (APMT....PDER-M2).
When cutting edge strength is particularly important, use the H breaker (APMT....PDER-H2).
MILLING
SCREW-IN ARBORS
K142
SPARE PARTS
M001
TECHNICAL DATA
N001
K131
MILLING
Tool Overhang
Recommended cutting conditions on this literature are chosen based on deection,
vibration and machined surface when using a CAT50 arbor. Conditions-"a" is the
length from a gage line to the arbor end face, and "b" is the neck length (tool
overhang from the arbor).
(Inch)
Cutting Diameter : D1
Type
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
.625"
.750"
1.000"
1.250"
ap
max.
Inner / Outer
Maximum cutting
edge length
Peripheral
1.5
2.5
3.5
1.5
2.5
3.5
2.0
3.0
4.0
2.0
3.5
5.0
5.5
6.5
7.5
5.5
6.5
7.5
6.0
7.0
8.0
6.0
7.5
9.0
Recommended Depth of Cut for Long Cutting Edge Type

The maximum cutting edge length of the long cutting edge type with a peripheral
insert is 1.4-1.5D1. The peripheral insert is for light machining only.
Maximum ap is 0.5D1 or below.
(Long cutting edge type)
Cutting Mode
y SLOT MILLING
N: Spindle Speed (RPM)

F: Table Feed (IPM)
Work Material
MILLING
Carbon Steel
Alloy Steel
Hardness
Cutting
Speed
(SFM)
Grade
500
180280HB (
375667)
VP15TF
458
280350HB (
375542)
VP15TF
375
Pre-Hardened Steel 3545HRC (333500
) VP15TF
Alloy Tool Steel
< 350HB
458
(375542)
VP15TF
Stainless Steel
< 270HB
500
(333667)
VP15TF
Gray Cast Iron
< 350MPa
667
(5001000) VP15TF
< 500MPa
583
(500750)
VP15TF
< 800MPa
500
(500750)
VP15TF
4550HRC
333
(167417)
VP15TF
5060HRC
188
(125333)
VP15TF
Ductile Cast Iron
H
Heat Treated Steel
K132
Type
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
& .625"
(& 16mm)
N
F
ap
3056
3056
3056
2801
2801
2801
2292
2292
2292
2801
2801
2801
3056
3056
3056
4074
4074
4074
3565
3565
3565
3056
3056
3056
2037
2037
2037
1146
1146
1146
14
14
14
13
13
13
11
11
11
13
13
13
14
14
14
32
32
26
28
28
22
24
24
19
10
10
10
5
5
5
.236
.157
.079
.236
.157
.079
.236
.157
.079
.236
.157
.079
.157
.118
.079
.236
.157
.079
.236
.157
.079
.236
.157
.079
.157
.079
.039
.157
.079
.039
& .750"
(& 20mm)
N
F
ap
2546
2546
2546
2334
2334
2334
1910
1910
1910
2334
2334
2334
2546
2546
2546
3395
3395
3395
2971
2971
2971
2546
2546
2546
1698
1698
1698
955
955
955
12
12
12
11
11
11
9
9
9
11
11
11
12
12
12
27
27
27
23
23
23
20
20
20
8
8
8
5
5
5
.315
.157
.079
.315
.157
.079
.315
.157
.079
.315
.157
.079
.197
.118
.059
.315
.157
.079
.315
.157
.079
.315
.157
.079
.157
.079
.039
.157
.079
.039
& 1.000"
(& 25mm)
N
F
ap
1910
1910
1910
1751
1751
1751
1432
1432
1432
1751
1751
1751
1910
1910
1910
2546
2546
2546
2228
2228
2228
1910
1910
1910
1273
1273
1273
716
716
716
18
18
18
17
17
17
14
14
14
17
17
17
18
18
18
24
24
24
21
21
21
18
18
18
12
12
12
7
7
7
.500
.500
.333
.500
.500
.333
.500
.500
.333
.500
.500
.333
.500
.500
.333
.500
.500
.333
.500
.500
.333
.500
.500
.333
.500
.500
.333
.500
.500
.333
& 1.250"
(& 32mm)
N
F
ap
1528
1528
1528
1401
1401
1401
1146
1146
1146
1401
1401
1401
1528
1528
1528
2037
2037
2037
1783
1783
1783
1528
1528
1528
1019
1019
1019
573
573
573
14
14
14
13
13
13
11
11
11
13
13
13
14
14
14
19
19
19
17
17
17
14
14
14
10
10
10
5
5
5
.625
.625
.417
.625
.625
.417
.625
.625
.417
.625
.625
.417
.625
.625
.417
.625
.625
.417
.625
.625
.417
.625
.625
.417
.625
.625
.417
.625
.625
.417
ap
Cutting Mode
y SHOULDER MILLING (Cutting Depth : Small)
Work Material
P
Carbon Steel
Alloy Steel
Hardness
Cutting
Speed
(SFM)
Grade
625
180280HB (
375750)
VP15TF
500
280350HB (
375667)
VP15TF
500
(375667)
VP15TF
Pre-Hardened Steel 3545HRC
N : Spindle Speed (RPM)

F : Table Feed (IPM)
ae
Alloy Tool Steel
< 350HB
500
(375542)
VP15TF
Stainless Steel
< 270HB
625
(333667)
VP15TF
Gray Cast Iron
< 350MPa
625
(5001000) VP15TF
< 500MPa
625
(500750)
VP15TF
< 800MPa
583
(500750)
VP15TF
4550HRC
333
(167417)
VP15TF
5060HRC
188
(125333)
VP15TF
Ductile Cast Iron
H
Heat Treated Steel
Type
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
& .625"
(& 16mm)
N
F ap ae
3820
3820
3820
3056
3056
3056
3056
3056
3056
3056
3056
3056
3820
3820
3820
3820
3820
3820
3820
3820
3820
3565
3565
3565
2037
2037
2037
1146
1146
1146
30
24
18
19
14
14
19
14
14
19
14
14
18
18
18
60
45
36
60
45
36
56
42
34
10
10
10
5
5
5
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
.236
.157
.079
.236
.157
.079
.236
.157
.079
.236
.157
.079
.236
.157
.079
.315
.236
.157
.315
.236
.157
.315
.236
.157
.157
.079
.039
.157
.079
.039
& .750"
(& 20mm)
N
F ap ae
3183
3183
3183
2546
2546
2546
2546
2546
2546
2546
2546
2546
3183
3183
3183
3183
3183
3183
3183
3183
3183
2971
2971
2971
1698
1698
1698
955
955
955
38
25
15
20
16
12
20
16
12
20
16
12
20
15
15
63
50
38
63
50
38
58
47
35
8
8
8
5
5
5
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.197
.315
.236
.157
.315
.236
.157
.315
.236
.157
.315
.236
.157
.315
.236
.157
.394
.315
.236
.394
.315
.236
.394
.315
.236
.197
.118
.079
.197
.118
.079
& 1.000"
(& 25mm)
F ap ae
N
2387
2387
2387
1910
1910
1910
1910
1910
1910
1910
1910
1910
2387
2387
2387
2387
2387
2387
2387
2387
2387
2228
2228
2228
1273
1273
1273
716
716
716
28
23
23
23
18
18
23
18
18
23
18
18
28
23
23
32
23
23
28
23
23
26
21
21
15
12
12
8
7
7
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.250
.500
.400
.300
.500
.400
.300
.500
.400
.300
.500
.400
.300
.500
.400
.300
.500
.400
.300
.500
.400
.300
.500
.400
.300
.250
.200
.150
.250
.200
.150
& 1.250"
(& 32mm)
N
F ap ae
1910
1910
1910
1528
1528
1528
1528
1528
1528
1528
1528
1528
1910
1910
1910
1910
1910
1910
1910
1910
1910
1783
1783
1783
1019
1019
1019
573
573
573
23
18
18
18
14
14
18
14
14
18
14
14
23
18
18
26
18
18
23
18
18
21
17
17
12
10
10
7
5
5
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.313
.625
.500
.375
.625
.500
.375
.625
.500
.375
.625
.500
.375
.625
.500
.375
.625
.500
.375
.625
.500
.375
.625
.500
.375
.313
.250
.188
.313
.250
.188
y SHOULDER MILLING (Cutting Depth : Large)
Carbon Steel
Alloy Steel
Hardness
Cutting
Speed
(SFM)
Grade
625
180280HB (
375750)
VP15TF
500
280350HB (
375667)
VP15TF
500
(375667)
VP15TF
Pre-Hardened Steel 3545HRC
Alloy Tool Steel
< 350HB
500
(375542)
VP15TF
Stainless Steel
< 270HB
625
(333667)
VP15TF
Gray Cast Iron
< 350MPa
625
(5001000) VP15TF
< 500MPa
625
(500750)
VP15TF
< 800MPa
583
(500750)
VP15TF
4550HRC
333
(167417)
VP15TF
5060HRC
188
(125333)
VP15TF
Ductile Cast Iron
H
Heat Treated Steel
Type
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
Short
Medium
Long
& .625"
(& 16mm)
N
F ap ae
3820
3820
3820
3056
3056
3056
3056
3056
3056
3056
3056
3056
3820
3820
3820
3820
3820
3820
3820
3820
3820
3565
3565
3565
2037
2037
2037
1146
1146
1146
24
18
18
14
14
14
14
14
14
14
14
14
18
18
18
45
36
30
45
36
30
42
34
28
10
10
10
5
5
5
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.315
.157
.118
.079
.157
.118
.079
.157
.118
.079
.157
.118
.079
.157
.118
.079
.315
.197
.118
.315
.197
.118
.315
.197
.118
.079
.039
.039
.079
.039
.039
& .750"
(& 20mm)
N
F ap ae
3183
3183
3183
2546
2546
2546
2546
2546
2546
2546
2546
2546
3183
3183
3183
3183
3183
3183
3183
3183
3183
2971
2971
2971
1698
1698
1698
955
955
955
30
20
15
20
12
12
20
12
12
20
12
12
20
15
15
50
38
30
50
38
30
47
35
28
8
8
8
5
5
5
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.394
.157
.118
.079
.157
.118
.079
.157
.118
.079
.157
.118
.079
.157
.118
.079
.315
.157
.079
.315
.157
.079
.315
.157
.079
.118
.079
.039
.118
.079
.039
& 1.000"
(& 25mm)
N
F ap ae
2387
2387
2387
1910
1910
1910
1910
1910
1910
1910
1910
1910
2387
2387
2387
2387
2387
2387
2387
2387
2387
2228
2228
2228
1273
1273
1273
716
716
716
28
23
23
23
18
18
23
18
18
23
18
18
28
23
23
32
23
23
28
23
23
26
21
21
15
12
12
8
7
7
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.250
.250
.200
.250
.250
.200
.250
.250
.200
.250
.250
.200
.333
.267
.200
.333
.267
.200
.333
.267
.200
.333
.267
.200
.200
.160
.120
.200
.160
.120
& 1.250"
(& 32mm)
N
F ap ae
1910
1910
1910
1528
1528
1528
1528
1528
1528
1528
1528
1528
1910
1910
1910
1910
1910
1910
1910
1910
1910
1783
1783
1783
1019
1019
1019
573
573
573
23
18
18
18
14
14
18
14
14
18
14
14
23
18
18
26
18
18
23
18
18
21
17
17
12
10
10
7
5
5
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.625
.313
.313
.250
.313
.313
.250
.313
.313
.250
.313
.313
.250
.417
.333
.250
.417
.417
.333
.417
.417
.333
.417
.417
.333
.250
.200
.150
.250
.200
.150
MILLING
N : Spindle Speed (RPM)

F : Table Feed (IPM)
ae
Work Material
Down cutting (Climb milling) is preferred.
ap
Cutting Mode
*Machining Stainless Steels
K133
MILLING
BALL NOSE
END MILL
SRM2
Including
curved faces
Roughing
40 (1.575")
50 (1.969 ")
a Combination Type
a Morse Taper Type
a Straight Type
METRIC Standard
Long Standard Long Standard Extra Long Long Standard
Morse Taper
D1
D4
L1
L2
ap
.787
.984
.787
.984
1.575
1.969
1.575
1.969
2.000
2.000
2.000
2.000
7.874
7.874
9.843
9.843
4.724
4.724
6.693
6.693
2.126
2.480
2.126
2.480

Insert Screw
TS6S
TS43
TS6
TS43
TS6S
TS43
TS6
TS43

Wrench
TKY30T TKY15F
TKY30T TKY15F
TKY30T TKY15F
TKY30T TKY15F
Inner
SRM2400WNLS
2500WNLS
2400WNLM
2500WNLM
s
s
s
2
2
2
2
2500WNLL
2 .984 1.969 2.000 11.811 8.661 2.480
TS6
TS43
TKY30T TKY15F SRG50C
2500WNLX
2 .984 1.969 2.000 13.780 10.630 2.480
TS6
TS43
SRM2400SNLS
2500SNLS
2400SNLM
2500SNLM
s
s
s
s
2
2
2
2
TS6S
TS6
TS6S
TS6
TS43
TS43
TS43
TS43
TKY30T
TKY30T
TKY30T
TKY30T
SRM2500MNLS
2 .984 1.969
10.079 4.724 2.480
TS6
TS43
2500MNLM
2 .984 1.969
11.260 5.906 2.480
TS6
TS43
.787
.984
.787
.984
1.575
1.969
1.575
1.969
1.654
1.654
1.654
1.654
7.874
7.874
9.843
9.843
3.937
3.937
5.906
3.937
2.126
2.480
2.126
2.480
TKY15F
TKY15F
TKY15F
TKY15F
SRG40C
SRG50C
SRG40C
SRG50C
SRG40C
SRG50C
SRG40C
SRG50C
Outer
Peripheral
Insert
SRG40E APMT1604
PDER-p2
SRG50E APMT1604
PDER-p2
SRG40E APMT1604
PDER-p2
SRG50E APMT1604
PDER-p2
APMT1604
SRG50E
PDER-p2
APMT1604
SRG50E
PDER-p2
SRG40E APMT1604
PDER-p2
SRG50E APMT1604
PDER-p2
APMT1604
SRG40E PDER-p2
SRG50E APMT1604
PDER-p2
APMT1604
SRG50E
PDER-p2
APMT1604
SRG50E
PDER-p2
INSERTS
Dimensions (inch)
Inner
Shape
Strong Cutting
Edge Type
Order Number
Class
VP15TF
VP20RT
VP30RT
Coated
Outer
Peripheral
K134
Dimensions (inch)
* Clamp Torque (lbf-in) : TS43=31, TS6=89, TS6S=89

Application
MILLING
Straight
Combination
Number of Flutes
Order Number
Stock
Type
L1
L2
S1
F1
Re
.787 1.417 .807 .315

.984 1.575 1.024 .335

.787 1.260 .654 .315

.984 1.409 .787 .335

* SRG40C
50C
*
G
G
s s s
* SRG40E
50E
*
G
G
s s s
APMT1604PDER-M2
.650 .375 .187 .055 .031
APMT1604PDER-H2
.650 .375 .187 .055 .031
in one case.
* 2ainserts
s s s
s s s
Geometry

B : Shoulder Milling (Standard Type)
A : Slot Milling
C : Shoulder Milling (Long Cutting Edge Type)
Cutting
Mode
Hardness
Grade
Cutting Speed
(SFM)
Alloy Tool Steel
< 250HB
VP20RT
VP30RT
655 (525 820)
Cast Tool Steel
< 230HB
VP15TF
VP20RT
655 (525 985)
VP15TF
VP20RT
655 (525 985)
VP15TF
VP20RT
655 (525 985)
Work Material
K
Ductile Cast Iron
Gray Cast Iron
Tensile Strength
< 540MPa
Tensile Strength
< 350MPa
Feed per Tooth

(IPR)
Cutting
Mode
.008 (.004 .012)

.008 (.004 .016)
.012 (.004 .016)
.008 (.004 .012)
.012 (.004 .018)
.008 (.004 .016)
.010 (.004 .016)
.010 (.004 .018)
.014 (.004 .018)
.010 (.004 .016)
.014 (.004 .018)
.010 (.004 .016)
A
B
C
A
B
C
A
B
C
A
B
C
y GRADE APPLICATION GUIDE

Gray Cast Iron Ductile Cast Iron
Cast Tool Steel
Alloy Tool Steel
VP15TF
VP20RT
VP30RT
Toughness
MILLING
Wear Resistance
SPARE PARTS
M001
TECHNICAL DATA
N001
K135
MILLING
BALL NOSE
END MILL
Including
curved faces
TRM4
Light Alloy
Cast Iron
Including
Flat faces
Roughing
(Max. Depth of Cut)
a Large ball-nose endmill suitable
for roughing of large molds.

a Economical 3-corner-use inserts.
a Curved cutting edge and rigid
holder are stable in heavy cutting.

Number
of Teeth
Order Number
Stock
Dimensions (inch)
R
L1
D1
D4
L2
L3
ap
Insert
UPM40
UPM40P1
UPM40
UPM40P1
UPM50
UPM50P1/P0
UPM50
UPM50P1/P0
.750
1.500
8.000 2.000
4.750
4.000
1.875
CS451190T
zTKY20R
424W32M
.750
1.500 10.000 2.000
6.750
6.000
1.875
CS451190T
zTKY20R
TRM432W32S
1.000
2.000
8.000 2.000
4.000
2.250
CS501290T
xTKY25T
432W32M
1.000
2.000 10.000 2.000
6.000
2.250
CS501290T
xTKY25T
Dimensions (inch)
VP15TF
AP20M
L1
S1
.984
.650
.236
UPM40
50
.787
.984
.520
.650
.189
.236
UPM40P1
50P1
.787
.984
.520
.650
.189
.236
Order Number
General
UPM50P0
Strong Cutting
Edge Type
Lower Cutting
Resistance Type
Coated
CUTTING MODE
.3D1
Work Material
B : Shoulder Milling (Standard Type)

K
Grade
Carbon Steel
180 280
HB
AP20M
VP15TF
Alloy Steel
180 280
HB
VP15TF
650
(560 750)
Tensile Strength AP20M

< 350MPa VP15TF
720
(620 820)
AP20M
600
(530 660)
Gray Cast Iron

Hardened Steel
1.0D1
C : Shoulder Milling (Long Edge Type)
200 280
HB
Heat Treated Steel > 40 HRC

.1D1

Cutting Speed
(SFM)
Hardness
.917D1
Geometry
A : Grooving
Clamp Torque (lbf-in) : CS451190T=44, CS501290T=66
Class
Shape
MILLING
Wrench
TRM424W32S
INSERTS
K136
Insert Screw
AP20M
VP15TF
AP20M
VP15TF
750
(620 820)
320
(260 390)
Cutting Mode
Feed (IPR)
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
.014 (.010 .024)

.016 (.010 .032)
.016 (.010 .040)
.014 (.010 .024)
.016 (.010 .032)
.016 (.010 .040)
.014 (.010 .024)
.016 (.010 .032)
.016 (.010 .040)
.014 (.010 .024)
.016 (.010 .032)
.016 (.010 .040)
.014 (.010 .024)
.016 (.010 .032)
.016 (.010 .040)
VERTICAL FEED
MILLING
Roughing
PMC
part of press mould.
D5
a For under-cutting trimmed
D4
D1
a 2 directional cutting with
ae(Max.Depth of Cut)
L4
L2
L1
large overhang.
a Suitable for automated
3 axis programming.
H1
SECTION A-A
L11
PMC08R252AM1035
25 10.5 18 58.7 39.7 35
14 M10 1.5 35 40.5 0.1
JOMp080320
ZZSR-pp
SC20M10S
ppppW
09R323AM1245
32 12.5 21 72.5 50.5 45
19 M12 3
35 40.5 0.2
JDMp09T320
ZDSR-pp
SC25M12S
ppppW
12R403AM1645
40 17
24 M16 3.5 35 40.5 0.3
JDMp120420
ZDSR-pp
SC32M16S
ppppW
Order Number
Mass
Coolant Hole
D1
Stock
R
Number of Teeth

Dimensions (mm)
D4
D5
L1
L2
L4 L11 H1
29 74.4 51.4 45
M*
ae
Shank Arbor
(kg)
Insert
*1 Clamp Torque of the Head(lbf-ft) : M10=33.8, M12=59.2, M16=66.7

SPARE PARTS
Clamp Bridge
Screw
Clamp
Bridge
Clamp
Screw
Spring
Wrench
Anti-seize
Lubricant
TS33
AMS3
AJS3010T10
ASS2
xTKY08D
zTKY10R
MK1KS
09R323AM1245
TS351
AMS3
AJS3010T10
ASS2
xTKY10D
MK1KS
12R403AM1645
TS43
AMS4
AJS4012T15
ASS2
xTKY15D
MK1KS
PMC08R252AM1035
Clamp Torque (lbf-in) : TS33=8.9, TS351=22, TS43=31, AJS3010T10=22, AJS4012T15=31
INSERTS
Dimensions (mm)
Coated
Shape
FT
Breaker
Class
FH7020
VP15TF
VP30RT
MILLING
Order Number
B 3
JOMW080320ZZSR-FT
a a a
13 8
3.18 1.4
PMC08R252AM1035
JDMW09T320ZDSR-FT
a a a
15 9.525 3.97 1.8
PMC09R323AM1245
120420ZDSR-FT
a a a
15 12
4.76 2.5
PMC12R403AM1645
Order Number
D1
S1
F1
Re
PMC holder
Geometry
B3
F1
D1
ST
Breaker
JDMT120420ZDSR-ST
a a a
15 12
4.76 2.5
S1
PMC12R403AM1645
B3
F1
D1
JM
Breaker
Re
JOMT080320ZZSR-JM M
a a a
13 8
3.18 1.4
PMC08R252AM1035
JDMT09T320ZDSR-JM M
a a a
15 9.525 3.97 1.8
PMC09R323AM1245
120420ZDSR-JM M
a a a
15 12
4.76 2.5
PMC12R403AM1645
Re
S1
B 3
F1
D1
Re
S1
SPARE PARTS
M001
TECHNICAL DATA
N001
K137
MILLING
Work Material
Hardness
Carbon Steel
Alloy Steel
< 180HB
Hardening Tool Steel

for Cold Work Dies
< 300HB
< 300HB
Alloy Tool Steel
Tensile
Strength
Cast Iron
Grade
VP15TF
VP15TF
VP15TF
VP15TF
Breaker
Cutting
Dia.
(mm)
Number
of Teeth
Cutting Speed
(SFM)
Feed per Tooth

(inch/tooth)
Width of Cut
(inch)
Pick Feed
(inch)
& 40
820 (655 985)
.024
.059
.236
& 32
655 (490 720)
.022
.047
.197
& 25
655 (490 720)
.022
.039
.197
& 40
820 (655 985)
.022
.059
.197
& 32
590 (490 655)
.020
.047
.118
& 25
FT
FT
FT
FT
<350MPa
Tensile
Strength
Ductile Cast Iron
VP15TF
FT
< 800MPa
590 (490 655)
.020
.039
.118
& 40
655 (330 985)
.022
.059
.197
& 32
490 (260 655)
.020
.047
.118
& 25
490 (260 655)
.020
.039
.118
& 40
820 (655 985)
.024
.059
.236
& 32
655 (490 720)
.022
.047
.197
& 25
655 (490 720)
.022
.039
.197
& 40
820 (655 985)
.024
.059
.236
& 32
655 (490 720)
.022
.047
.197
& 25
655 (490 720)
.022
.039
.197
(Note 1) The above cutting conditions are general guide lines. Adjustments maybe necessary depending on machine rigidity,
workpiece geometry and clamping.
(Note 2) A carbide shank extension is recommended to prevent vibrations.
Application of Breakers
Cutting
Conditions
Breaker
Light
Cutting
Application of Insert Grades
General
Cutting
JM
Interrupted
Cutting
Cutting
Conditions
Light
Cutting
Interrupted
Cutting
General
Cutting
FH7020
FT
Grade
(First recommended)
VP15TF
ST
(First recommended)
VP30RT
MILLING
NOTES ON MACHINING METHODS

a How to choose an appropriate diameter tool.
Machine plain surfaces with a larger tool and corner radii with smaller diameter cutters.
Cutting point
PMC
Small type
PMC
Large type
PMC
a Relation of the cutter diameter and corner R size of work piece

A guide for the smallest possible workpiece radius that can be machined is from 0.6 0.7 x diameter of the tool.
C
rR
Tool diameter
D1(mm)
Corner R
(inch)
6
0.
or
& 25
R > .689
& 32
R > .866
& 40
R > .945
1x
ne
.7
~0
PMC
D1
* Adjust cutting conditions according to the set up.

* Smaller workpiece corner radii (only >0.5 x cutter &) may be possible
by reducing the width of cut, speed and pick feed.
K138
SCREW-IN ARBORS
K142
VERTICAL FEED
MILLING
PMR
Light Alloy
Cast Iron
Roughing
a 1 directional cutting with large overhang.

a Unique shape of curved edge gives
high rigidity and low resistance.

Stock
Order Number
Inch
Metric
PMR405003A22R
406304A22R
408005A27R
PMR405003BR
406304BR
408005DR
s
s
s
s
s
s
Number of Teeth
D1
L1
D9
L7
D8
D12
W1
L8
ap
3
4
5
3
4
5
50
63
80
50
63
80
40
40
50
40
40
63
22
22
27
22.225
22.225
31.75
20
20
23
19
19
32
11
11
13.5
11
11
17
45
57
73
45
57
73
10.4
10.4
12.4
8.4
8.4
12.7
6.3
6.3
7
5
5
8
11
11
11
11
11
11
Dimensions (mm)
Insert
CPMT1205ZPEN-M2/3
CPMT1205ZPEN-M2/3
CPMT1205ZPEN-M2/3
CPMT1205ZPEN-M2/3
CPMT1205ZPEN-M2/3
CPMT1205ZPEN-M2/3
SPARE PARTS
Shim Screw
Order Number
Shim
PMR405003A22R
406304A22R
408005A27R
405003BR
406304BR
408005DR
Insert
Insert Screw
Shim
Shim Screw
Insert Screw
STPMR4N
STPMR4N
STPMR4N
STPMR4N
STPMR4N
STPMR4N
WCS503507H
WCS503507H
WCS503507H
WCS503507H
WCS503507H
WCS503507H
TPS35
TPS35
TPS35
TPS35
TPS35
TPS35
TIP15T
TIP15T
TIP15T
TIP15T
TIP15T
TIP15T
HKY35R
HKY35R
HKY35R
HKY35R
HKY35R
HKY35R
Set Bolt
HSC10035
HSC10035
HSC12040
HSC10035
HSC10035
HSC16040
Order Number
Class
CPMT1205ZPEN-M2
1205ZPEN-M3
Dimensions (mm)
Coated
VP15TF F7030
s
D1
S1
F1
Re
12.7
5.56
1.4
0.8
12.7
5.56
1.4
1.2
MILLING
INSERTS
Shape
Geometry

Work Material
Carbon Steel
Alloy Steel
Hardness
180 280HB
280 380HB
Grade
Cutting Speed (SFM)
pf (mm)
VP15TF
590 (490 655)
.008 (.004 .012)
< .5D
Tensile Strength
< .5D
VP15TF
590 (490 655)
.008 (.004 .012)
< 350MPa
Tensile Strength
VP15TF
< .5D
490 (390 555)
.008 (.004 .012)
360 500MPa
Ductile Cast Iron
Tensile Strength
< .5D
390 (330 490)
.008 (.004 .012)
VP15TF
500 800MPa
(Note 1) The above conditions are suitable for general machining purposes, it is possible to use conditions that are different from the above.
(Note 2) For horizontal feed machining, please reduce the feed rate by 20 40%.
(Note 3) If vibration occurs when machining, please reduce the depth of cut, cutting speed by 20 50%.
Gray Cast Iron

ARBORS
K142
SPARE PARTS
M001
TECHNICAL DATA
N001
K139
MILLING
Cast Iron
63
D4
D9
W1
L8
D4
D9
W1
L1
L1
L7
Light Alloy
50
L7
PMF
Finishing
L8
VERTICAL FEED
MILLING
D8
D1
D4
D9
W1
80
L8
D8
D1
L1
L7
a 2 directional cutting with large overhang.

a No burring so no need for hand nishing.
a High precision multi directional insert
ensures highly accurate surfaces.
D8
D1
Stock
Number of Teeth
METRIC Standard
Order Number

2
z
Max.
*
*
x
Allowable Revolution
(min-1)
Insert Radial Set Bolt Wrench Wrench Set Bolt Insert
Balance
G40
*1 Cartridge Screw
W1 L8 D4 Unknown Balanced
Screw (Cartridge)
Dimensions (mm)
D1 L1 D9 L7 D8
HKY40R
HKY50R
zHDS10031
PMF05004A22R
4 50 63 22 20 12
10.4 6.3 48 6300 12700 PMFA13R TS254 TSS04005 HBH06012 TKY08F
06306A22R
6 63 63 22 20 18
10.4 6.3 60 5000 10100 PMFA13R TS254 TSS04005 HBH06012 TKY08F HKY40R xHSC10050 1303
08008A27R
8 80 50 27 23 13.5 12.4 7
75 3900
TPEW
p
7900 PMFA13R TS254 TSS04005 HBH06012 TKY08F HKY40R xHSC12035 ZP R2
need to balance the tool and holder together so that it conrms to G40 or higher standards.
*12 You
Clamp Torque (lbf-in) : TS254=8.9, HBH06012=8.5
*
INSERTS
Order Number
TPEW1303ZPTR2
a a
Dimensions (mm)
D1
S1
F1
7.94
3.18
7.94
3.18
Geometry
60
F1
F1
TPEW1303ZPER2
MB710
MILLING
Shape
Class
VP15TF
AP10H
Coated CBN
11
D1
* CBN
S1

Work Material
Hardness
Grade
180280HB
VP15TF
Carbon Steel
Alloy Steel
Gray
Cast Iron
280380HB
VP15TF
Tensile Strength
< 350MPa
AP10H
MB710

(SFM)
(inch/tooth)
820
(490 1150)
655
(330 985)
Work Material
K
.004
(.0019 .006)
Ductile
Cast Iron
Hardness
Grade
Tensile Strength
< 500MPa
AP10H
MB710
Tensile Strength
< 800MPa
MB710
AP10H

(SFM)
(inch/tooth)
820
(490 1150)
3280
(2625 3940)
655
(330 985)
3280
(2625 3940)
.004
(.002 .006)
.004
(.002 .006)
1150
(655 1640)
.004
(.0019 .006)
4920
(3280 6560)
(Note 1) Recommended radial depth of cut is .004" to .008"(1 2mm).

(Note 2) Up and down vertical cutting is recommended for efciency.
(Note 3) For crossfeed cutting, feed per tooth should be reduced to less than .002(inch/tooth).
K140
<10 inserts in one case> <1 insert in one case for CBN>
ARBORS
K141
LONG ARBORS
(Effective Neck Length)
Order Number
Stock
METRIC Standard
Dimensions (mm)
D5
D10
L10
L11
L3
Mass
(lbs)
Cutter
47
22
250
18
202
M10
14.3
PMF05004A22R, PMR405003A22R
22-250-063
60
22
250
18
202
M10
18.7
PMF06306A22R, PMR406304A22R
27-300-080
75
27
300
22
252
M12
27.6
PMF08008A27R, PMR408005A27R
22.225-250-050
47
22.225
250
17
202
M10
14.3
PMR405003BR
MILLING
BT50-22-250-050
PMF
K140
SPARE PARTS
M001
PMR
K139
TECHNICAL DATA
N001
K141
MILLING
SCREW-IN ARBORS
STRAIGHT SHANK ARBOR
D4
D9
D5
L2
L1
Stock
SC16M08S100S
08S200L
SC20M10S120S
10S220L
SC25M12S125S
12S245L
SC32M16S140S
16S280L
Coolant Thru
Type
Steel Shank
y STEEL SHANK TYPE

Order Number
s u
s u
s u
s u
s u
s u
s u
Mass
D9
D4
D5
L1
L2
H1
8.5
8.5
10.5
10.5
12.5
12.5
17
17
16
16
20
20
25
25
32
32
14.5
14.5
18.5
18.5
23.5
23.5
28.5
28.5
100
200
120
220
125
245
140
280
10
10
10
10
10
10
15
15
10
10
14
14
19
19
24
24
M8
M8
M10
M10
M12
M12
M16
M16
(kg)
0.1
0.3
0.3
0.5
0.4
0.8
0.8
1.6
METRIC Standard
Stock
Coolant Thru
Type
Carbide Shank
MILLING
SC16M08S100SW
08S200LW
SC20M10S120SW
10S220LW
SC25M12S125SW
12S245LW
SC32M16S140SW
16S280LW
Dimensions (mm)
s u
y CARBIDE SHANK TYPE

Order Number
H1
METRIC Standard
Dimensions (mm)
s u
s u
s u
s u
s u
s u
s u
s u
Mass
D9
D4
D5
L1
L2
H1
(kg)
8.5
8.5
10.5
10.5
12.5
12.5
17
17
16
16
20
20
25
25
32
32
14.5
14.5
18.5
18.5
23.5
23.5
28.5
28.5
100
200
120
220
125
245
140
280
10
10
10
10
10
10
15
15
10
10
14
14
19
19
24
24
M8
M8
M10
M10
M12
M12
M16
M16
0.2
0.5
0.5
0.9
0.8
1.5
1.4
2.8
HSK SHANK ARBOR
HSK63A
63
D5
D9
C4
SC16M08S22-HSK63A
20M10S24-HSK63A
25M12S27-HSK63A
32M16S28-HSK63A
K142
Coolant Thru
Order Number
L2
METRIC Standard
Stock
y HSK63A SHANK ARBOR
s u
s u
s u
s u
L10
Dimensions (mm)
Mass
D9
D5
L10
L2
(kg)
8.5
10.5
12.5
17.0
14.5
18.5
23.5
28.5
48
50
53
54
22
24
27
28
M8
M10
M12
M16
0.7
0.7
0.7
0.8
BT SHANK ARBOR
BT30
D5
D9
L2
Stock
y BT30 SHANK ARBOR
Coolant Thru
METRIC Standard
Order Number
SC16M08S10-BT30
20M10S10-BT30
25M12S10-BT30
32M16S10-BT30
s u
s u
s u
s u
L10
Dimensions (mm)
Mass
D9
D5
L10
L2
8.5
10.5
12.5
17.0
14.5
18.5
23.5
28.5
32
32
32
32
10
10
10
10
M8
M10
M12
M16
0.4
0.4
0.4
0.4
BT40
D5
D9
(kg)
L2
Order Number
SC16M08S10-BT40
20M10S10-BT40
25M12S10-BT40
32M16S10-BT40
s u
s u
s u
s u
L10
Dimensions (mm)
Mass
D9
D5
L10
L2
8.5
10.5
12.5
17.0
14.5
18.5
23.5
28.5
37
37
37
37
10
10
10
10
M8
M10
M12
M16
(kg)
1.0
1.0
1.0
1.0
HOW TO INSTALL THE SCREW-IN HEAD
MILLING
Stock
y BT40 SHANK ARBOR
Coolant Thru
METRIC Standard
z Thoroughly clean the clamp section of the head and the

arbor with an air blower or brush before installation.
x Tighten the head at the recommended torque and ensure
that there is no gap between the head and arbor.
Screw Size
Recommended Torque
(lbf-ft)
Wrench Size
(mm)
M8
M10
M12
M16
17.1
33.8
59.2
66.7
10
14
19
24
a Cutting tools become extremely hot during cutting. Never touch them with bare hands after operation as this may produce risk of
injuries or burns.
a Do not handle the cutting tools with bare hands as this may cause injuries.
SPARE PARTS
M001
TECHNICAL DATA
N001
K143
MILLING
MAXIMUM SPINDLE SPEED FOR CUTTER

ASX445
Diameter
AHX640W
AOX445
FBP415
Max.
Clamp
Max.
Clamp
Max.
Clamp
Max.
Clamp
Spindle Torque Spindle Torque Spindle Torque Spindle Torque
Speed
Speed
Speed
Speed
(min-1) (lbf-in) (min-1) (lbf-in) (min-1) (lbf-in) (min-1) (lbf-in)
2.0"
18000
31
13000
71
2.5"
16000
31
12000
71
3.0"
14000
31
9200
53
11000
71
16600
75
4.0"
13000
31
7700
53
9300
71
14300
75
5.0"
12000
31
6500
53
8300
71
12400
75
6.0"
10000
31
5500
53
7200
71
10800
75
8.0"
9000
31
4000
53
6400
71
9300
75
10.0"
8000
31
2800
53
8100
75
1900
53
7000
75
12.0"
BF407
Diameter
ASX400
AXD7000
NSE300
NSE400
PMF
Clamp
Max.
Clamp
Max.
Clamp
Max.
Clamp
Max.
Clamp
Max.
Clamp
Max.
Clamp
Max.
Spindle Torque Spindle Torque Spindle Torque Spindle Torque Spindle Torque Spindle Torque Spindle Torque
Speed
Speed
Speed
Speed
Speed
Speed
Speed
(min-1) (lbf-in) (min-1) (lbf-in) (min-1) (lbf-in) (min-1) (lbf-in) (min-1) (lbf-in) (min-1) (lbf-in) (min-1) (lbf-in)
1.0"
MILLING
BXD4000
38000
35
1.25"
41000
31
33000
35
1.5"
36000
31
29000
35
2.0"
18000
31
30000
31
24000
35
8900
75
12700
8.9
2.5"
16000
31
25000
31
21000
35
7700
75
10100
8.9
7900
8.9
3.0"
15700
75
14000
31
23000
31
19000
35
13700
75
12000
75
4.0"
13500
75
13000
31
19000
31
16000
35
11800
75
10300
75
5.0"
11800
75
12000
31
16000
31
9000
75
6.0"
10200
75
10000
31
7800
75
8.0"
8800
75
9000
31
6700
75
10.0"
7600
75
8000
31
12.0"
6600
75
All values shown on this chart are based on the insert being properly seated in pocket and torqued to the recommended values.
(Note) You need to balance the tool and holder together so that it conrms to G40 or higher standards.
K144
Memo
K145
GUIDE TO DRILLING TOOLS

aSection
organization
zOrganized according to cutting mode for drilling. (Refer to DRILL LIST.)
PHOTO OF PRODUCT
GEOMETRY
PRODUCT TYPE
PRODUCT SECTION
DRILLING(SOLID CARBIDE)
a Suitable
for high efciency and high accuracy drilling over a wide

variety of materials from general steel to difcult-to-cut materials.
for low to high speed cutting.
MWS
.1250< D1< .2344 .2500< D1< .3906 .4062< D1< .7031 .7188< D1< .7812
D1 Tolerance
(inch)
D4 Tolerance
(inch)
INCH STANDARD
0
.00071
0
.00031
0
.00130
0
.00051
0
.00106
0
.00043
0
.00087
0
.00035
MWS (Internal coolant)
.1495
5 Int.
8 Int.
.1562
5 Int.
8 Int.
5 Int.
8 Int.
.1693 8 Int.
.1719
5 Int.
8 Int.
.1875
5 Int.
8 Int.
5 Int.
.2031
8 Int.
.2130 8 Int.
.2188
5 Int.
8 Int.
.2344
5 Int.
8 Int.
5 Int.
.2500
8 Int.
5 Int.
.2570
8 Int.
5 Int.
8 Int.
5 Int.
.2720
8 Int.
.1590
.2656
MWS01250LB
01250X8DB
01405LB
01406X8DB
01495LB
01495X8DB
01562LB
01562X8DB
01590LB
01590X8DB
01693X8DB
01719LB
01719X8DB
01875LB
01875X8DB
02031LB
02031X8DB
02130X8DB
02188LB
02188X8DB
02344LB
02344X8DB
02500LB
02500X8DB
02570LB
02570X8DB
02656LB
02656X8DB
02720LB
02720X8DB
L2
L1
D4
1.535 1.535 3.425 .1575

1.535 1.535 3.425 .1575
Hole Depth
L3
D1
(inch) (l/d)
Coolant
(Int./Ext.)
Order Number
Drill
Dia.
.2812
5 Int.
8 Int.
.2969
5 Int.
8 Int.
1.732 1.732 3.622 .1575

1.732 1.732 3.622 .1575
.3125
5 Int.
8 Int.
1.732 1.732 3.622 .1575

1.732 1.732 3.622 .1575
.3281
5 Int.
8 Int.
1.969 1.969 3.937 .1969

1.969 1.969 3.937 .1969
.3320
5 Int.
8 Int.
5 Int.
.3438
8 Int.
5 Int.
8 Int.
1.732 1.732 3.622 .1575

1.732 1.732 3.622 .1575
1.969 1.969 3.937 .1969

1.969 1.969 3.937 .1969
1.969 1.969 3.937 .1969
2.165 2.165 4.134 .1969
2.165 2.165 4.134 .1969
1.732 1.890 3.937 .2344
2.402 2.599 4.646 .2344
2.402 2.599 4.646 .2344
.3594
5 Int.
8 Int.
5 Int.
.3750
8 Int.
.3680
Dimensions (inch)
Stock
VP15TF
Hole Depth
Coolant
(Int./Ext.)
5 Int.
8 Int.
.1405 5 Int.
.1406 8 Int.
.1250
DRILLING
VP15TF
D1
(inch) (l/d)
Dimensions (inch)
Stock
1.890 1.890 3.937 .2344

2.599 2.599 4.646 .2344
.3906
5 Int.
8 Int.
1.890 1.890 3.937 .2344

2.599 2.599 4.646 .2344
.4062
5 Int.
8 Int.
2.047 2.205 4.292 .2656

2.835 3.031 5.118 .2656
5 Int.
.4219
8 Int.
2.205 2.205 4.292 .2656

3.031 3.031 5.118 .2656
5 Int.
.4375
8 Int.
2.205 2.205 4.292 .2656

3.031 3.031 5.118 .2656
.4531
5 Int.
8 Int.
2.205 2.205 4.292 .2720

3.031 3.031 5.118 .2720
5 Int.
.4688
8 Int.
Order Number
MWS02812LB
02812X8DB
02969LB
02969X8DB
03125LB
03125X8DB
03281LB
03281X8DB
03320LB
03320X8DB
03438LB
03438X8DB
03594LB
03594X8DB
03680LB
03680X8DB
03750LB
03750X8DB
03906LB
03906X8DB
04062LB
04062X8DB
04219LB
04219X8DB
04375LB
04375X8DB
04531LB
04531X8DB
04688LB
04688X8DB
L3
L2
L1
Dimensions (inch)
Stock
.4844
5 Int.
8 Int.
.5000
5 Int.
8 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
.5050
.5118
.5156
.5312
.5469
.5625
.5781
.5937
.6094
(Note 1) MWS type larger than &.2031" have a recess in the shank end face.
(Note 2) MWS type can be used for shrink t holders.
Drill
Dia.
Drill
Dia.
D1
(inch) (l/d)
Order Number
L3
MWS04844LB
04844X8DB
05000LB
05000X8DB
05050LB
05118LB
05156LB
05312LB
05469LB
05625LB
05781LB
05937LB
06094LB
L2
L1
Drill
Dia.
D4
3.937 4.095 6.575 .5000

5.433 5.630 8.110 .5000
4.094 4.095 6.575 .5000
5.630 5.630 8.110 .5000
4.094 4.095 6.575 .5118
4.094 4.095 6.575 .5118
4.250 4.409 6.922 .5469
4.250 4.409 6.922 .5469
4.406 4.409 6.922 .5469
4.563 4.722 7.281 .5781
4.719 4.722 7.281 .5781
4.875 5.035 7.594 .6250
4.875 5.035 7.594 .6250
D1
(inch) (l/d)
.6250
.6330
.6406
.6563
.6718
.6875
.7031
.7188
.7344
.7500
.7580
.7656
.7812
Dimensions (inch)
Stock
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
Order Number
L3
MWS06250LB
06330LB
06406LB
06563LB
06718LB
06875LB
07031LB
07188LB
07344LB
07500LB
07580LB
07656LB
07812LB
L2
L1
D4
5.031 5.035 7.594 .6250

5.197 5.354 7.913 .6563
5.197 5.354 7.913 .6563
5.354 5.354 7.913 .6563
5.512 5.669 8.228 .7031
5.512 5.669 8.228 .7031
5.669 5.669 8.228 .7031
5.827 5.984 8.543 .7344
5.984 5.984 8.543 .7344
6.142 6.299 8.858 .7812
6.142 6.299 8.858 .7812
6.142 6.299 8.858 .7812
6.299 6.299 8.858 .7812
D4
2.362 2.520 4.646 .3125

3.268 3.465 5.591 .3125
2.520 2.520 4.646 .3125
3.465 3.465 5.591 .3125
2.520 2.520 4.646 .3125

3.465 3.465 5.591 .3125
2.677 2.835 5.000 .3438
3.701 3.898 6.063 .3438
2.992 3.150 5.355 .3906

4.134 4.330 6.535 .3906
2.992 3.150 5.355 .3906
4.134 4.330 6.535 .3906
3.150 3.150 5.355 .3906
4.330 4.330 6.535 .3906
3.780 3.780 6.221 .4688

5.197 5.197 7.638 .4688
3.780 3.780 6.221 .4688
5.197 5.197 7.638 .4688
.008 (.006 .012)
430 (260 460)
.010 (.008 .014)
Carbon Steel
Alloy Steel
180 280HB
300 (160 330)
.008 (.006 .012)
360 (230 390)
.010 (.008 .014)
280 350HB
260 (130 300)
.008 (.006 .010)
300 (200 360)
.010 (.006 .012)

.008 (.004 .010)
Stainless Steel
200 (70 330)
.004 (.002 .006)
260 (130 390)
330 (230 390)
.010 (.006 .012)
430 (330 460)
200 (100 260)
.008 (.006 .010)
230 (130 300)
.008 (.006 .012)
390 (260 490)
.010 (.008 .014)
490 (330 560)
.012 (.008 .020)
70 (30 80)
.004 (.002 .006)
80 (50 100)
.005 (.002 .006)
< 200HB
Gray Cast Iron
Tensile Strength
Tensile Strength
Aluminum Alloy
Work Material
3.465 3.464 5.866 .4219

4.764 4.764 7.165 .4219
3.622 3.780 6.221 .4688
5.000 5.197 7.638 .4688
360 (160 390)
Ductile Cast Iron
3.150 3.150 5.355 .3906

4.330 4.330 6.535 .3906
3.307 3.464 5.866 .4219
4.567 4.764 7.165 .4219
&.2500" &.3906"
Cutting Speed
Feed
(SFM)
(IPR)
< 180HB
Drill Diameter
Conditions
Hardness
2.677 2.835 5.000 .3438

3.701 3.898 6.063 .3438
2.835 2.835 5.000 .3438
3.898 3.898 6.063 .3438
&.1250" &.2344"
Cutting Speed
Feed
(SFM)
(IPR)
Mild Steel
Work Material
< 350MPa
< 450MPa
Drill Diameter
Conditions
Hardness
&.4062" &.5469"
Cutting Speed
Feed
(SFM)
(IPR)
.012 (.006 .014)
&.5625" &.7812"
Cutting Speed
Feed
(SFM)
(IPR)
Mild Steel
< 180HB
490 (300 560)
.012 (.008 .016)
525 (330 590)
.014 (.008 .016)
Carbon Steel
Alloy Steel
180 280HB
430 (260 460)
.010 (.008 .016)
460 (330 490)
.012 (.008 .016)
280 350HB
360 (230 430)
.010 (.006 .014)
390 (295 460)
.012 (.008 .016)

.010 (.006 .012)
< 200HB
300 (160 390)
.010 (.006 .012)
330 (195 390)
Gray Cast Iron
Tensile Strength
490 (360 520)
.014 (.010 .016)
525 (390 555)
Ductile Cast Iron
Tensile Strength
300 (160 360)
.010 (.008 .016)
330 (195 360)
.012 (.008 .039)
Aluminum Alloy
520 (330 560)
.016 (.008 .032)
555 (330 590)
.020 (.008 .039)
80 (50 100)
.006 (.004 .008)
100 (80 115)
.008 (.004 .010)
Stainless Steel
< 350MPa
< 450MPa
DRILLING
Hole Depth
Heat Resistant
Alloy
Coolant
(Int./Ext.)
Light Alloy
VP15TF
Cast Iron
Hole Depth
Stainless
Steel
Coolant
(Int./Ext.)
Hardened
Steel
VP15TF
Carbon Steel
Alloy Steel
a Suitable
.014 (.010 .016)
(Note) Please contact Mitsubishi Materials for special grades and geometries other than our standard products.
L004
TECHNICAL DATA
PRODUCT STANDARDS
indicates diameters, order numbers,
stock status, numbers of teeth,
dimensions, and spare parts
for the title product.
LEGEND FOR STOCK

STATUS MARK
aTo
L000
Order:
N001
L005
PAGE REFERENCE
.TECHNICAL DATA
indicates the reference pages, including

the above, on the right hand page of

for each work material classication, indicates recommended
cutting conditions according to the ISO categories for cutting grades,
P, M, K, N, S and H.
For solid-carbide drill or brazed drill, please specify order number and grade.
For indexable type drill, please specify order number for drill.
For indexable type drill insert, please specify insert number and insert grade.
DRILLING TOOLS
DRILLS SELECTION CHART ........................................... L002
DRILL STANDARD
aSOLID CARBIDE TYPE
MWE/MWS DRILLS ..................................................... L004
MWS SUPER LONG DRILLS ...................................... L016
MZE/MZS DRILLS ....................................................... L026
MZS STEP DRILLS ..................................................... L037
MZE/MZS DRILLS (FOR TUBE SHEET) .................... L038
MICRO-MWS DRILLS ................................................. L040
MICRO-MZE/MZS DRILLS .......................................... L050
MSE DRILLS................................................................ L054
MSP DRILLS................................................................ L056
MICRO-MGS DRILLS (SOLID GUN DRILLS)............. L058
MMS DRILLS ............................................................... L060
MAS/MAE DRILLS ...................................................... L066
MNS DRILLS ............................................................... L074
MHS DRILLS ............................................................... L082
DRILLS FOR WHEEL HUB ......................................... L091
MCS DRILLS ............................................................... L092
aINDEXABLE
TYPE
STAW DRILLS ............................................................. L094
TAW DRILLS ............................................................... L098
TAW CHAMFER RING ................................................. L118
TAF DRILLS ................................................................ L120
aBRAZED TYPE
BRA DRILLS................................................................ L130
BRS DRILLS ................................................................ L132
*Arranged
BRA (INCH)
L130
L132
L068
L066
L068
L092
L059
L058
L091
L082
L060
L074
L054
L056
L006
L004
L006
L016
BRS (INCH)
MAE (METRIC)
MAS (INCH)
MAS (METRIC)
MCS (INCH)
MGD (INCH)
MGS (METRIC)
MHE
MHS (METRIC)
MMS (METRIC)
MNS (METRIC)
MSE (METRIC)
MSP (METRIC)
MWE (METRIC)
MWS (INCH)
MWS (METRIC)
MWS (LONG, INCH)
L018
L040
L042
L026
L028
L050
L051
L026
L028
L050
L051
L037
L094
L120
L123
L098
L106
MWS (LONG, METRIC)

MWS (MICRO, INCH)
MWS (MICRO, METRIC)
MZE (INCH)
MZE (METRIC)
MZE (MICRO, INCH)
MZE (MICRO, METRIC)
MZS (INCH)
MZS (METRIC)
MZS (MICRO, INCH)
MZS (MICRO, METRIC)
MZS (STEP DRILL, METRIC)
STAW (METRIC)
TAF (INCH)
TAF (METRIC)
TAW (INCH)
TAW (METRIC)
L001
DRILLING
L002
Cutting Conditions
Dimensions
Light Alloy
Cast Iron
L052
L051
L052
Internal
L050
External
L052
Internal
L051
External
METRIC
& 0.1 & 0.99 mm
e e e e e u L056 L056
METRIC
& 3.0 & 20.0 mm
e u u e u u L006 L015
3
5
2
3
3
5
8
3
10
15
20
25
30
MWS
15
20
25
30
MGS
20
MZS
L052
External
MZS
L050
External
MZE
L047
e u u e u u L054 L055
Internal
MWS
L042
METRIC
& 0.1 & 0.99 mm
External
MWE
L047
Internal
MSP
L040
Internal
MSE
Internal
MZS
INCH
&.0200" &.1200"
Page
Internal
General Use
Starter Drill
for MSE Type
General Use
Step Drill
MZE
MWS Super
Long Type
MWS
1
5
12
20
25
30
1
5
12
Solid Gun
Drill
For General Size Hole (> & .1250", & 3.0mm)

For Deep Hole
( > l/d
10)
DRILLING
Solid Carbide
For Micro Size Hole ( < & .1200", & 2.95mm)
INCH METRIC
Stainless Steel
Range of Size
Hardened Steel
Hole
Depth
(I /d)
Carbon Steel
Alloy Steel
Work Material
Coolant
Product Code
Drill Type
Category
Drill Structure
DRILLS SELECTION CHART
80
METRIC
& 0.5 & 2.95 mm
INCH
&.0394" &.1200"
METRIC
& 1.0 & 2.9 mm
INCH
&.0394" &.1200"
METRIC
& 1.0 & 2.9 mm
INCH
& .1250" &.7812"
METRIC
& 3.0 & 25.0 mm
INCH
&.1250" &.7812"
METRIC
& 3.0 & 20.0 mm
INCH
&.1250" &.7812"
METRIC
& 3.0 & 20.0 mm
METRIC
& 4.3 & 8.5 mm
INCH
&.1250" &.5000"
METRIC
& 3.0 &14.0 mm
METRIC
& 0.7 & 3.0 mm
e e u u
e u u e u u
e e u u
L004
L005
L006
L015
L026
L039
L028
L039
L026
L039
L028
L039
e e u u
e u u e u u
e e u u
e e u u L037 L039
e e u u
L016
L017
L018
L017
e u e e e u L058 L059
Shape
3
6
MHE
L091
L091
L092
L092
L094
L096
L098
L111
L106
L111
L120
L128
L123
L128
3
5
METRIC
& 10.0 &13.9 mm
3
5
8
2
3
4
Internal
Internal
Internal
Internal
Internal
L089
INCH
&.1719 " &.5010"
Multi-corner
Insert
Light Alloy
L082
Cast Iron
L039
BRS
Indexable
Head
L028
INCH
&.3 9 4 " &.591"
L073
u e
BRA
L068
METRIC
& 3.0 &20.0 mm
2
3
4
L067
2
3
30
TAF
TAW
L066
METRIC
& 3.0 &12.0 mm
INCH
&.5625" &1.1875"
METRIC
&14.0 & 30.0 mm
INCH
&.468" &2.250"
METRIC
&12.0 & 56.0 mm
INCH
&.3125" &1.250"
METRIC
& 8.0 & 30.0 mm
INCH
&.5000" &1.1875"
METRIC
&14.0 & 30.0 mm
Shape
u e
L079
3
5
8
L073
L074
STAW
L068
MCS
L064
METRIC
& 3.0 &14.0 mm
MHS
(HTi10)
L060
5
10
20
30
Internal
MZE
u e
METRIC
& 3.0 &16.0 mm
External
MNS
INCH
&.1250" &.7812"
Internal
MAS
For CFRP
u e u
e e
DRILLING
METRIC
& 3.0 & 16.0 mm
Page
Cutting Conditions
Dimensions
Internal
External
MAE
Internal
METRIC
& 3.0 & 20.0 mm
External
2 coolant
holes
Helix Angle
(10)
4 coolant
holes
3
5
New Point
Type
CVD Diamond Low Cutting

General Use General Use
Coating
Resistance
MMS
High Helix
(30)
For Aluminum or Cast Iron

For General Use
For General Use
Brazed
Indexable
For
For CFRP For Wheel Hub Hardened
Steel
Solid Carbide
For
Stainless Steel
INCH METRIC
Stainless Steel
Range of Size
Hardened Steel
Hole
Depth
(I /d)
Carbon Steel
Alloy Steel
Coolant
Product Code
Drill Type
Category
Drill Structure
Work Material
P
e e e
u u
L130
L131
e u
L132
L133
L003
a Suitable

a Suitable for low to high speed cutting.
MWS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
.1250< D1< .2344 .2500< D1< .3906 .4062< D1< .7031 .7188< D1< .7812
D1 Tolerance
(inch)
D4 Tolerance
(inch)
INCH STANDARD
0
.00071
0
.00031
0
.00106
0
.00043
0
.00087
0
.00035
0
.00130
0
.00051
5 Int.
8 Int.
.1405 5 Int.
.1406 8 Int.
.1495
5 Int.
8 Int.
.1562
5 Int.
8 Int.
.1590
5 Int.
8 Int.
.1693 8 Int.
5 Int.
.1719
8 Int.
5 Int.
.1875
8 Int.
5 Int.
.2031
8 Int.
.2130 8 Int.
.2188
5 Int.
8 Int.
.2344
5 Int.
8 Int.
.2500
5 Int.
8 Int.
.2570
5 Int.
8 Int.
.2656
5 Int.
8 Int.
.2720
5 Int.
8 Int.
DRILLING
.1250
MWS01250LB
01250X8DB
01405LB
01406X8DB
01495LB
01495X8DB
01562LB
01562X8DB
01590LB
01590X8DB
01693X8DB
01719LB
01719X8DB
01875LB
01875X8DB
02031LB
02031X8DB
02130X8DB
02188LB
02188X8DB
02344LB
02344X8DB
02500LB
02500X8DB
02570LB
02570X8DB
02656LB
02656X8DB
02720LB
02720X8DB
L2
L1
D4
1.535 1.535 3.425 .1575

1.535 1.535 3.425 .1575
D1
(inch) (l/d)
.2812
5 Int.
8 Int.
.2969
5 Int.
8 Int.
1.732 1.732 3.622 .1575

1.732 1.732 3.622 .1575
.3125
5 Int.
8 Int.
1.732 1.732 3.622 .1575

1.732 1.732 3.622 .1575
.3281
5 Int.
8 Int.
1.969 1.969 3.937 .1969

1.969 1.969 3.937 .1969
.3320
5 Int.
8 Int.
.3438
5 Int.
8 Int.
.3594
5 Int.
8 Int.
.3680
5 Int.
8 Int.
.3750
5 Int.
8 Int.
1.890 1.890 3.937 .2344

2.599 2.599 4.646 .2344
.3906
5 Int.
8 Int.
1.890 1.890 3.937 .2344

2.599 2.599 4.646 .2344
.4062
5 Int.
8 Int.
2.047 2.205 4.292 .2656

2.835 3.031 5.118 .2656
.4219
5 Int.
8 Int.
2.205 2.205 4.292 .2656

3.031 3.031 5.118 .2656
.4375
5 Int.
8 Int.
2.205 2.205 4.292 .2656

3.031 3.031 5.118 .2656
.4531
5 Int.
8 Int.
2.205 2.205 4.292 .2720

3.031 3.031 5.118 .2720
.4688
5 Int.
8 Int.
1.732 1.732 3.622 .1575

1.732 1.732 3.622 .1575
1.969 1.969 3.937 .1969

1.969 1.969 3.937 .1969
1.969 1.969 3.937 .1969
2.165 2.165 4.134 .1969
2.165 2.165 4.134 .1969
1.732 1.890 3.937 .2344
2.402 2.599 4.646 .2344
2.402 2.599 4.646 .2344
Dimensions (inch)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(inch) (l/d)
Dimensions (inch)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
(Note 1) MWS type larger than &.2031" have a recess in the shank end face.
Order Number
MWS02812LB
02812X8DB
02969LB
02969X8DB
03125LB
03125X8DB
03281LB
03281X8DB
03320LB
03320X8DB
03438LB
03438X8DB
03594LB
03594X8DB
03680LB
03680X8DB
03750LB
03750X8DB
03906LB
03906X8DB
04062LB
04062X8DB
04219LB
04219X8DB
04375LB
04375X8DB
04531LB
04531X8DB
04688LB
04688X8DB
L004
L3
L2
L1
D4
2.362 2.520 4.646 .3125

3.268 3.465 5.591 .3125
2.520 2.520 4.646 .3125
3.465 3.465 5.591 .3125
2.520 2.520 4.646 .3125
3.465 3.465 5.591 .3125
2.677 2.835 5.000 .3438
3.701 3.898 6.063 .3438
2.677 2.835 5.000 .3438
3.701 3.898 6.063 .3438
2.835 2.835 5.000 .3438
3.898 3.898 6.063 .3438
2.992 3.150 5.355 .3906
4.134 4.330 6.535 .3906
2.992 3.150 5.355 .3906
4.134 4.330 6.535 .3906
3.150 3.150 5.355 .3906
4.330 4.330 6.535 .3906
3.150 3.150 5.355 .3906
4.330 4.330 6.535 .3906
3.307 3.464 5.866 .4219
4.567 4.764 7.165 .4219
3.465 3.464 5.866 .4219
4.764 4.764 7.165 .4219
3.622 3.780 6.221 .4688
5.000 5.197 7.638 .4688
3.780 3.780 6.221 .4688
5.197 5.197 7.638 .4688
3.780 3.780 6.221 .4688
5.197 5.197 7.638 .4688
5 Int.
8 Int.
5 Int.
.5000
8 Int.
.5050
.5118
.5156
.5312
.5469
.5625
.5781
.5937
.6094
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
.4844
MWS04844LB
04844X8DB
05000LB
05000X8DB
05050LB
05118LB
05156LB
05312LB
05469LB
05625LB
05781LB
05937LB
06094LB
L2
L1
D4
3.937 4.095 6.575 .5000

5.433 5.630 8.110 .5000
4.094 4.095 6.575 .5000
5.630 5.630 8.110 .5000
4.094 4.095 6.575 .5118
4.094 4.095 6.575 .5118
4.250 4.409 6.922 .5469
4.250 4.409 6.922 .5469
4.406 4.409 6.922 .5469
4.563 4.722 7.281 .5781
4.719 4.722 7.281 .5781
4.875 5.035 7.594 .6250
4.875 5.035 7.594 .6250
D1
(inch) (l/d)
.6250
.6330
.6406
.6563
.6718
.6875
.7031
.7188
.7344
.7500
.7580
.7656
.7812
Dimensions (inch)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
Dimensions (inch)
Stock
VP15TF
Hole Depth
D1
(inch) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
5 Int.
Order Number
L3
MWS06250LB
06330LB
06406LB
06563LB
06718LB
06875LB
07031LB
07188LB
07344LB
07500LB
07580LB
07656LB
07812LB
L2
L1
D4
5.031 5.035 7.594 .6250

5.197 5.354 7.913 .6563
5.197 5.354 7.913 .6563
5.354 5.354 7.913 .6563
5.512 5.669 8.228 .7031
5.512 5.669 8.228 .7031
5.669 5.669 8.228 .7031
5.827 5.984 8.543 .7344
5.984 5.984 8.543 .7344
6.142 6.299 8.858 .7812
6.142 6.299 8.858 .7812
6.142 6.299 8.858 .7812
6.299 6.299 8.858 .7812
Work Material
Drill Diameter
Conditions
Hardness
&.1250" &.2344"
Cutting Speed
Feed
(SFM)
(IPR)
&.2500" &.3906"
Cutting Speed
Feed
(SFM)
(IPR)
Mild Steel
< 180HB
360 (160 390)
.008 (.006 .012)
430 (260 460)
.010 (.008 .014)
Carbon Steel
Alloy Steel
180 280HB
300 (160 330)
.008 (.006 .012)
360 (230 390)
.010 (.008 .014)
280 350HB
260 (130 300)
.008 (.006 .010)
300 (200 360)
.010 (.006 .012)
Stainless Steel
< 200HB
200 (70 330)
.004 (.002 .006)
260 (130 390)
.008 (.004 .010)
Gray Cast Iron
Tensile Strength
330 (230 390)
.010 (.006 .012)
430 (330 460)
.012 (.006 .014)
Ductile Cast Iron
Tensile Strength
200 (100 260)
.008 (.006 .010)
230 (130 300)
.008 (.006 .012)
Aluminum Alloy
390 (260 490)
.010 (.008 .014)
490 (330 560)
.012 (.008 .020)
70 (30 80)
.004 (.002 .006)
80 (50 100)
.005 (.002 .006)
Work Material
< 350MPa
< 450MPa
Drill Diameter
Conditions
Hardness
&.4062" &.5469"
Cutting Speed
Feed
(SFM)
(IPR)
&.5625" &.7812"
Cutting Speed
Feed
(SFM)
(IPR)
Mild Steel
< 180HB
490 (300 560)
.012 (.008 .016)
525 (330 590)
.014 (.008 .016)
Carbon Steel
Alloy Steel
180 280HB
430 (260 460)
.010 (.008 .016)
460 (330 490)
.012 (.008 .016)
280 350HB
360 (230 430)
.010 (.006 .014)
390 (295 460)
.012 (.008 .016)
< 200HB
300 (160 390)
.010 (.006 .012)
330 (195 390)
.010 (.006 .012)
490 (360 520)
.014 (.010 .016)
525 (390 555)
.014 (.010 .016)
300 (160 360)
.010 (.008 .016)
330 (195 360)
.012 (.008 .039)
Stainless Steel
Gray Cast Iron
Tensile Strength
Ductile Cast Iron
Tensile Strength
Aluminum Alloy
520 (330 560)
.016 (.008 .032)
555 (330 590)
.020 (.008 .039)
80 (50 100)
.006 (.004 .008)
100 (80 115)
.008 (.004 .010)
< 350MPa
< 450MPa
TECHNICAL DATA
N001
DRILLING
L005
a Suitable

MWE/MWS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
u(only MWE) e(MWE:u)
Light Alloy
Heat Resistant
Alloy
D1=3 3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 25

D1 Tolerance
(mm)
D4 Tolerance
METRIC STANDARD
MWE (External coolant)
(mm)
MWE
MWS
0
0.014
0
0.014
0
0.006
0
0.018
0
0.018
0
0.008
0
0.022
0
0.022
0
0.009
0
0.027
0
0.027
0
0.011
0
0.033
0
0.033
0
0.013
3.0
3.1
DRILLING
3.2
3.3
3.4
3.5
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
MWE0300SA
MWE0300MA
MWS0300MB
MWS0300LB
MWS0300X8DB
MWE0310SA
MWE0310MA
MWS0310MB
MWS0310LB
MWS0310X8DB
MWE0320SA
MWE0320MA
MWS0320MB
MWS0320LB
MWS0320X8DB
MWE0330SA
MWE0330MA
MWS0330MB
MWS0330LB
MWS0330X8DB
MWE0340SA
MWE0340MA
MWS0340MB
MWS0340LB
MWS0340X8DB
MWE0350SA
MWE0350MA
MWS0350MB
MWS0350LB
MWS0350X8DB
L2
L1
D4
16
21
16
21
55
60
3.0
3.0
24
24
72
3.0
33
35
33
35
81
81
3.0
3.0
18
24
18
24
55
60
3.1
3.1
28
28
76
4.0
39
41
39
41
87
87
4.0
4.0
18
24
18
24
55
60
3.2
3.2
28
28
76
4.0
39
41
39
41
87
87
4.0
4.0
18
24
18
24
55
60
3.3
3.3
28
28
76
4.0
39
41
39
41
87
87
4.0
4.0
20
24
20
24
55
60
3.4
3.4
28
28
76
4.0
39
41
39
41
87
87
4.0
4.0
20
24
20
24
55
60
3.5
3.5
28
28
76
4.0
39
41
39
41
87
87
4.0
4.0
D1
(mm) (l/d)
3.6
3.7
3.8
3.9
4.0
4.1
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
(Note 1) MWS type larger than & 5.0 have a recess in the shank end face.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
Order Number
MWE0360SA
MWE0360MA
MWS0360MB
MWS0360LB
MWS0360X8DB
MWE0370SA
MWE0370MA
MWS0370MB
MWS0370LB
MWS0370X8DB
MWE0380SA
MWE0380MA
MWS0380MB
MWS0380LB
MWS0380X8DB
MWE0390SA
MWE0390MA
MWS0390MB
MWS0390LB
MWS0390X8DB
MWE0400SA
MWE0400MA
MWS0400MB
MWS0400LB
MWS0400X8DB
MWE0410SA
MWE0410MA
MWS0410MB
MWS0410LB
MWS0410X8DB
L006
L3
L2
L1
D4
20
27
20
27
55
60
3.6
3.6
32
32
80
4.0
44
46
44
46
92
92
4.0
4.0
20
27
20
27
55
60
3.7
3.7
32
32
80
4.0
44
46
44
46
92
92
4.0
4.0
22
27
22
27
55
60
3.8
3.8
32
32
80
4.0
44
46
44
46
92
92
4.0
4.0
22
27
22
27
55
60
3.9
3.9
32
32
80
4.0
44
46
44
46
92
92
4.0
4.0
22
27
22
27
55
60
4.0
4.0
32
32
80
4.0
44
46
44
46
92
92
4.0
4.0
22
29
22
29
55
63
4.1
4.1
36
36
86
5.0
50
52
50
52
100
100
5.0
5.0
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
MWE0420SA
MWE0420MA
MWS0420MB
MWS0420LB
MWS0420X8DB
MWE0430SA
MWE0430MA
MWS0430MB
MWS0430LB
MWS0430X8DB
MWE0440SA
MWE0440MA
MWS0440MB
MWS0440LB
MWS0440X8DB
MWE0450SA
MWE0450MA
MWS0450MB
MWS0450LB
MWS0450X8DB
MWE0460SA
MWE0460MA
MWS0460MB
MWS0460LB
MWS0460X8DB
MWE0470SA
MWE0470MA
MWS0470MB
MWS0470LB
MWS0470X8DB
MWE0480SA
MWE0480MA
MWS0480MB
MWS0480LB
MWS0480X8DB
MWE0490SA
MWE0490MA
MWS0490MB
MWS0490LB
MWS0490X8DB
MWE0500SA
MWE0500MA
MWS0500MB
MWS0500LB
MWS0500X8DB
L1
D4
22
29
22
29
55
63
4.2
4.2
36
36
86
5.0
50
52
50
52
100
100
5.0
5.0
24
29
24
29
58
63
4.3
4.3
36
36
86
5.0
50
52
50
52
100
100
5.0
5.0
24
29
24
29
58
63
4.4
4.4
36
36
86
5.0
50
52
50
52
100
100
5.0
5.0
24
29
24
29
58
63
4.5
4.5
36
36
86
5.0
50
52
50
52
100
100
5.0
5.0
24
32
24
32
58
68
4.6
4.6
40
40
90
5.0
55
57
55
57
105
105
5.0
5.0
24
32
24
32
58
68
4.7
4.7
40
40
90
5.0
55
57
55
57
105
105
5.0
5.0
26
32
26
32
62
68
4.8
4.8
40
40
90
5.0
55
57
55
57
105
105
5.0
5.0
26
32
26
32
62
68
4.9
4.9
40
40
90
5.0
55
57
55
57
105
105
5.0
5.0
26
32
26
32
62
68
5.0
5.0
27.5
30
82
6.0
44
57
48
57
100
105
6.0
5.0
D1
(mm) (l/d)
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
Dimensions (mm)
Stock
VP15TF
L2
Hole Depth
L3
Coolant
(Int./Ext.)
Order Number
Drill
Dia.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
Order Number
MWE0510SA
MWE0510MA
MWS0510MB
MWS0510LB
MWS0510X8DB
MWE0520SA
MWE0520MA
MWS0520MB
MWS0520LB
MWS0520X8DB
MWE0530SA
MWE0530MA
MWS0530MB
MWS0530LB
MWS0530X8DB
MWE0540SA
MWE0540MA
MWS0540MB
MWS0540LB
MWS0540X8DB
MWE0550SA
MWE0550MA
MWS0550MB
MWS0550LB
MWS0550X8DB
MWE0560SA
MWE0560MA
MWS0560MB
MWS0560LB
MWS0560X8DB
MWE0570SA
MWE0570MA
MWS0570MB
MWS0570LB
MWS0570X8DB
MWE0580SA
MWE0580MA
MWS0580MB
MWS0580LB
MWS0580X8DB
MWE0590SA
MWE0590MA
MWS0590MB
MWS0590LB
MWS0590X8DB
L3
L2
L1
D4
26
34
26
34
62
72
5.1
5.1
27.5
30
82
6.0
44
61
48
66
100
118
6.0
6.0
26
34
26
34
62
72
5.2
5.2
27.5
30
82
6.0
44
61
48
66
100
118
6.0
6.0
26
34
26
34
62
72
5.3
5.3
27.5
30
82
6.0
44
61
48
66
100
118
6.0
6.0
28
34
28
34
66
72
5.4
5.4
27.5
30
82
6.0
44
61
48
66
100
118
6.0
6.0
28
34
28
34
66
72
5.5
5.5
27.5
30
82
6.0
44
61
48
66
100
118
6.0
6.0
28
36
28
36
66
74
5.6
5.6
30
30
82
6.0
48
66
48
66
100
118
6.0
6.0
28
36
28
36
66
74
5.7
5.7
30
30
82
6.0
48
66
48
66
100
118
6.0
6.0
28
36
28
36
66
74
5.8
5.8
30
30
82
6.0
48
66
48
66
100
118
6.0
6.0
28
36
28
36
66
74
5.9
5.9
30
30
82
6.0
48
66
48
66
100
118
6.0
6.0
CUTTING CONDITIONS
L015
TECHNICAL DATA
N001
DRILLING
4.2
Dimensions (mm)
Stock
VP15TF
Hole Depth
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
L007
a Suitable

MWE/MWS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Heat Resistant
Alloy
Light Alloy
D1=3 3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 25

D1 Tolerance
(mm)
D4 Tolerance
METRIC STANDARD
(mm)
MWE
MWS
0
0.014
0
0.014
0
0.006
0
0.018
0
0.018
0
0.008
0
0.022
0
0.022
0
0.009
0
0.027
0
0.027
0
0.011
0
0.033
0
0.033
0
0.013
6.0
6.1
DRILLING
6.2
6.3
6.4
6.5
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
MWE0600SA
MWE0600MA
MWS0600MB
MWS0600LB
MWS0600X8DB
MWE0610SA
MWE0610MA
MWS0610MB
MWS0610LB
MWS0610X8DB
MWE0620SA
MWE0620MA
MWS0620MB
MWS0620LB
MWS0620X8DB
MWE0630SA
MWE0630MA
MWS0630MB
MWS0630LB
MWS0630X8DB
MWE0640SA
MWE0640MA
MWS0640MB
MWS0640LB
MWS0640X8DB
MWE0650SA
MWE0650MA
MWS0650MB
MWS0650LB
MWS0650X8DB
L2
L1
D4
28
41
28
41
66
81
6.0
6.0
30
30
82
6.0
48
66
48
66
100
118
6.0
6.0
31
41
31
41
70
81
6.1
6.1
D1
(mm) (l/d)
6.6
6.7
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
32.5
35
88
7.0
3 Int.
52
72
56
77
109
130
7.0
7.0
5 Int.
8 Int.
31
41
31
41
70
81
6.2
6.2
2 Ext.
3 Ext.
6.8
32.5
35
88
7.0
3 Int.
52
72
56
77
109
130
7.0
7.0
5 Int.
8 Int.
31
41
31
41
70
81
6.3
6.3
2 Ext.
3 Ext.
6.9
32.5
35
88
7.0
3 Int.
52
72
56
77
109
130
7.0
7.0
5 Int.
8 Int.
31
41
31
41
70
81
6.4
6.4
2 Ext.
3 Ext.
7.0
32.5
35
88
7.0
3 Int.
52
72
56
77
109
130
7.0
7.0
5 Int.
8 Int.
31
41
31
41
70
81
6.5
6.5
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
32.5
35
88
7.0
52
72
56
77
109
130
7.0
7.0
7.1
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
Order Number
MWE0660SA
MWE0660MA
MWS0660MB
MWS0660LB
MWS0660X8DB
MWE0670SA
MWE0670MA
MWS0670MB
MWS0670LB
MWS0670X8DB
MWE0680SA
MWE0680MA
MWS0680MB
MWS0680LB
MWS0680X8DB
MWE0690SA
MWE0690MA
MWS0690MB
MWS0690LB
MWS0690X8DB
MWE0700SA
MWE0700MA
MWS0700MB
MWS0700LB
MWS0700X8DB
MWE0710SA
MWE0710MA
MWS0710MB
MWS0710LB
MWS0710X8DB
L008
L3
L2
L1
D4
31
43
31
43
70
83
6.6
6.6
35
35
88
7.0
56
77
56
77
109
130
7.0
7.0
31
43
31
43
70
83
6.7
6.7
35
35
88
7.0
56
77
56
77
109
130
7.0
7.0
34
43
34
43
74
83
6.8
6.8
35
35
88
7.0
56
77
56
77
109
130
7.0
7.0
34
43
34
43
74
83
6.9
6.9
35
35
88
7.0
56
77
56
77
109
130
7.0
7.0
34
43
34
43
74
83
7.0
7.0
35
35
88
7.0
56
77
56
77
109
130
7.0
7.0
34
45
34
45
74
87
7.1
7.1
37.5
40
94
8.0
60
83
64
88
118
142
8.0
8.0
7.3
7.4
7.5
7.6
7.7
7.8
7.9
8.0
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
MWE0720SA
MWE0720MA
MWS0720MB
MWS0720LB
MWS0720X8DB
MWE0730SA
MWE0730MA
MWS0730MB
MWS0730LB
MWS0730X8DB
MWE0740SA
MWE0740MA
MWS0740MB
MWS0740LB
MWS0740X8DB
MWE0750SA
MWE0750MA
MWS0750MB
MWS0750LB
MWS0750X8DB
MWE0760SA
MWE0760MA
MWS0760MB
MWS0760LB
MWS0760X8DB
MWE0770SA
MWE0770MA
MWS0770MB
MWS0770LB
MWS0770X8DB
MWE0780SA
MWE0780MA
MWS0780MB
MWS0780LB
MWS0780X8DB
MWE0790SA
MWE0790MA
MWS0790MB
MWS0790LB
MWS0790X8DB
MWE0800SA
MWE0800MA
MWS0800MB
MWS0800LB
MWS0800X8DB
L1
D4
34
45
34
45
74
87
7.2
7.2
37.5
40
94
8.0
60
83
64
88
118
142
8.0
8.0
34
45
34
45
74
87
7.3
7.3
37.5
40
94
8.0
60
83
64
88
118
142
8.0
8.0
34
45
34
45
74
87
7.4
7.4
37.5
40
94
8.0
60
83
64
88
118
142
8.0
8.0
34
45
34
45
74
87
7.5
7.5
37.5
40
94
8.0
60
83
64
88
118
142
8.0
8.0
37
48
37
48
79
90
7.6
7.6
40
40
94
8.0
64
88
64
88
118
142
8.0
8.0
37
48
37
48
79
90
7.7
7.7
40
40
94
8.0
64
88
64
88
118
142
8.0
8.0
37
48
37
48
79
90
7.8
7.8
40
40
94
8.0
64
88
64
88
118
142
8.0
8.0
37
48
37
48
79
90
7.9
7.9
40
40
94
8.0
64
88
64
88
118
142
8.0
8.0
37
48
37
48
79
90
8.0
8.0
40
40
94
8.0
64
88
64
88
118
142
8.0
8.0
D1
(mm) (l/d)
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
Dimensions (mm)
Stock
VP15TF
L2
Hole Depth
L3
Coolant
(Int./Ext.)
Order Number
Drill
Dia.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
Order Number
MWE0810SA
MWE0810MA
MWS0810MB
MWS0810LB
MWS0810X8DB
MWE0820SA
MWE0820MA
MWS0820MB
MWS0820LB
MWS0820X8DB
MWE0830SA
MWE0830MA
MWS0830MB
MWS0830LB
MWS0830X8DB
MWE0840SA
MWE0840MA
MWS0840MB
MWS0840LB
MWS0840X8DB
MWE0850SA
MWE0850MA
MWS0850MB
MWS0850LB
MWS0850X8DB
MWE0860SA
MWE0860MA
MWS0860MB
MWS0860LB
MWS0860X8DB
MWE0870SA
MWE0870MA
MWS0870MB
MWS0870LB
MWS0870X8DB
MWE0880SA
MWE0880MA
MWS0880MB
MWS0880LB
MWS0880X8DB
MWE0890SA
MWE0890MA
MWS0890MB
MWS0890LB
MWS0890X8DB
L3
L2
L1
D4
37
53
37
53
79
96
8.1
8.1
42.5
45
100
9.0
68
94
72
99
127
154
9.0
9.0
37
53
37
53
79
96
8.2
8.2
42.5
45
100
9.0
68
94
72
99
127
154
9.0
9.0
37
53
37
53
79
96
8.3
8.3
42.5
45
100
9.0
68
94
72
99
127
154
9.0
9.0
37
53
37
53
79
96
8.4
8.4
42.5
45
100
9.0
68
94
72
99
127
154
9.0
9.0
37
53
37
53
79
96
8.5
8.5
42.5
45
100
9.0
68
94
72
99
127
154
9.0
9.0
40
55
40
55
84
98
8.6
8.6
45
45
100
9.0
72
99
72
99
127
154
9.0
9.0
40
55
40
55
84
98
8.7
8.7
45
45
100
9.0
72
99
72
99
127
154
9.0
9.0
40
55
40
55
84
98
8.8
8.8
45
45
100
9.0
72
99
72
99
127
154
9.0
9.0
40
55
40
55
84
98
8.9
8.9
45
45
100
9.0
72
99
72
99
127
154
9.0
9.0
CUTTING CONDITIONS
L015
TECHNICAL DATA
N001
DRILLING
7.2
Dimensions (mm)
Stock
VP15TF
Hole Depth
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
L009
a Suitable

MWE/MWS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Heat Resistant
Alloy
Light Alloy
D1=3 3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 25

D1 Tolerance
(mm)
D4 Tolerance
METRIC STANDARD
(mm)
MWE
MWS
0
0.014
0
0.014
0
0.006
0
0.018
0
0.018
0
0.008
0
0.022
0
0.022
0
0.009
0
0.027
0
0.027
0
0.011
0
0.033
0
0.033
0
0.013
9.0
9.1
DRILLING
9.2
9.3
9.4
9.5
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
MWE0900SA
MWE0900MA
MWS0900MB
MWS0900LB
MWS0900X8DB
MWE0910SA
MWE0910MA
MWS0910MB
MWS0910LB
MWS0910X8DB
MWE0920SA
MWE0920MA
MWS0920MB
MWS0920LB
MWS0920X8DB
MWE0930SA
MWE0930MA
MWS0930MB
MWS0930LB
MWS0930X8DB
MWE0940SA
MWE0940MA
MWS0940MB
MWS0940LB
MWS0940X8DB
MWE0950SA
MWE0950MA
MWS0950MB
MWS0950LB
MWS0950X8DB
L2
L1
D4
40
55
40
55
84
98
9.0
9.0
45
45
100
9.0
72
99
72
99
127
154
9.0
9.0
40
58
40
58
84
102
9.1
9.1
47.5
D1
(mm) (l/d)
9.6
9.7
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
50
106
10.0
3 Int.
76
105
80
110
136
166
10.0
10.0
5 Int.
8 Int.
40
58
40
58
84
102
9.2
9.2
2 Ext.
3 Ext.
47.5
9.8
50
106
10.0
3 Int.
76
105
80
110
136
166
10.0
10.0
5 Int.
8 Int.
40
58
40
58
84
102
9.3
9.3
2 Ext.
3 Ext.
47.5
9.9
50
106
10.0
3 Int.
76
105
80
110
136
166
10.0
10.0
5 Int.
8 Int.
40
58
40
58
84
102
9.4
9.4
2 Ext.
3 Ext.
47.5
10.0
50
106
10.0
3 Int.
76
105
80
110
136
166
10.0
10.0
5 Int.
8 Int.
40
58
40
58
84
102
9.5
9.5
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
47.5
76
105
50
106
10.0
80
110
136
166
10.0
10.0
10.1
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
Order Number
MWE0960SA
MWE0960MA
MWS0960MB
MWS0960LB
MWS0960X8DB
MWE0970SA
MWE0970MA
MWS0970MB
MWS0970LB
MWS0970X8DB
MWE0980SA
MWE0980MA
MWS0980MB
MWS0980LB
MWS0980X8DB
MWE0990SA
MWE0990MA
MWS0990MB
MWS0990LB
MWS0990X8DB
MWE1000SA
MWE1000MA
MWS1000MB
MWS1000LB
MWS1000X8DB
MWE1010SA
MWE1010MA
MWS1010MB
MWS1010LB
MWS1010X8DB
L010
L3
L2
L1
D4
43
60
43
60
89
105
9.6
9.6
50
50
106
10.0
80
110
80
110
136
166
10.0
10.0
43
60
43
60
89
105
9.7
9.7
50
50
106
10.0
80
110
80
110
136
166
10.0
10.0
43
60
43
60
89
105
9.8
9.8
50
50
106
10.0
80
110
80
110
136
166
10.0
10.0
43
60
43
60
89
105
9.9
9.9
50
50
106
10.0
80
110
80
110
136
166
10.0
10.0
43
60
43
60
89
105
10.0
10.0
50
50
106
10.0
80
110
80
110
136
166
10.0
10.0
43
66
43
66
89
112
10.1
10.1
52.5
84
116
55
116
11.0
88
121
149
182
11.0
11.0
10.3
10.4
10.5
10.6
10.7
10.8
10.9
11.0
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
MWE1020SA
MWE1020MA
MWS1020MB
MWS1020LB
MWS1020X8DB
MWE1030SA
MWE1030MA
MWS1030MB
MWS1030LB
MWS1030X8DB
MWE1040SA
MWE1040MA
MWS1040MB
MWS1040LB
MWS1040X8DB
MWE1050SA
MWE1050MA
MWS1050MB
MWS1050LB
MWS1050X8DB
MWE1060SA
MWE1060MA
MWS1060MB
MWS1060LB
MWS1060X8DB
MWE1070SA
MWE1070MA
MWS1070MB
MWS1070LB
MWS1070X8DB
MWE1080SA
MWE1080MA
MWS1080MB
MWS1080LB
MWS1080X8DB
MWE1090SA
MWE1090MA
MWS1090MB
MWS1090LB
MWS1090X8DB
MWE1100SA
MWE1100MA
MWS1100MB
MWS1100LB
MWS1100X8DB
L1
D4
43
66
43
66
89
112
10.2
10.2
52.5
D1
(mm) (l/d)
11.1
2 Ext.
3 Ext.
a
a
55
116
11.0
3 Int.
84
116
88
121
149
182
11.0
11.0
5 Int.
8 Int.
43
66
43
66
89
112
10.3
10.3
2 Ext.
3 Ext.
52.5
11.2
55
116
11.0
3 Int.
84
116
88
121
149
182
11.0
11.0
5 Int.
8 Int.
43
66
43
66
89
112
10.4
10.4
2 Ext.
3 Ext.
11.3
55
116
11.0
3 Int.
84
116
88
121
149
182
11.0
11.0
5 Int.
8 Int.
43
66
43
66
89
112
10.5
10.5
2 Ext.
3 Ext.
52.5
11.4
55
116
11.0
3 Int.
84
116
88
121
149
182
11.0
11.0
5 Int.
8 Int.
43
68
43
68
89
114
10.6
10.6
2 Ext.
3 Ext.
55
55
116
11.0
3 Int.
88
121
88
121
149
182
11.0
11.0
5 Int.
8 Int.
47
68
47
68
95
114
10.7
10.7
2 Ext.
3 Ext.
55
55
116
11.0
3 Int.
88
121
88
121
149
182
11.0
11.0
5 Int.
8 Int.
47
68
47
68
95
114
10.8
10.8
2 Ext.
3 Ext.
55
55
116
11.0
3 Int.
88
121
88
121
149
182
11.0
11.0
5 Int.
8 Int.
47
68
47
68
95
114
10.9
10.9
2 Ext.
3 Ext.
55
55
116
11.0
3 Int.
88
121
88
121
149
182
11.0
11.0
5 Int.
8 Int.
47
68
47
68
95
114
11.0
11.0
2 Ext.
3 Ext.
55
55
116
11.0
3 Int.
88
121
88
121
149
182
11.0
11.0
5 Int.
8 Int.
52.5
11.5
11.6
11.7
11.8
11.9
Dimensions (mm)
Stock
VP15TF
L2
Hole Depth
L3
Coolant
(Int./Ext.)
Order Number
Drill
Dia.
Order Number
MWE1110SA
MWE1110MA
MWS1110MB
MWS1110LB
MWS1110X8DB
MWE1120SA
MWE1120MA
MWS1120MB
MWS1120LB
MWS1120X8DB
MWE1130SA
MWE1130MA
MWS1130MB
MWS1130LB
MWS1130X8DB
MWE1140SA
MWE1140MA
MWS1140MB
MWS1140LB
MWS1140X8DB
MWE1150SA
MWE1150MA
MWS1150MB
MWS1150LB
MWS1150X8DB
MWE1160SA
MWE1160MA
MWS1160MB
MWS1160LB
MWS1160X8DB
MWE1170SA
MWE1170MA
MWS1170MB
MWS1170LB
MWS1170X8DB
MWE1180SA
MWE1180MA
MWS1180MB
MWS1180LB
MWS1180X8DB
MWE1190SA
MWE1190MA
MWS1190MB
MWS1190LB
MWS1190X8DB
L3
L2
L1
D4
47
71
47
71
95
118
11.1
11.1
57.5
60
122
12.0
92
127
96
132
158
194
12.0
12.0
47
71
47
71
95
118
11.2
11.2
57.5
60
122
12.0
92
127
96
132
158
194
12.0
12.0
47
71
47
71
95
118
11.3
11.3
57.5
60
122
12.0
92
127
96
132
158
194
12.0
12.0
47
71
47
71
95
118
11.4
11.4
57.5
60
122
12.0
92
127
96
132
158
194
12.0
12.0
47
71
47
71
95
118
11.5
11.5
57.5
60
122
12.0
92
127
96
132
158
194
12.0
12.0
47
73
47
73
95
121
11.6
11.6
60
60
122
12.0
96
132
96
132
158
194
12.0
12.0
47
73
47
73
95
121
11.7
11.7
60
60
122
12.0
96
132
96
132
158
194
12.0
12.0
47
73
47
73
95
121
11.8
11.8
60
60
122
12.0
96
132
96
132
158
194
12.0
12.0
51
73
51
73
102
121
11.9
11.9
60
60
122
12.0
96
132
96
132
158
194
12.0
12.0
CUTTING CONDITIONS
L015
TECHNICAL DATA
N001
DRILLING
10.2
Dimensions (mm)
Stock
VP15TF
Hole Depth
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
L011
a Suitable

MWE/MWS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
D1=3 3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 25

D1 Tolerance
(mm)
D4 Tolerance
METRIC STANDARD
(mm)
MWE
MWS
0
0.014
0
0.014
0
0.006
0
0.018
0
0.018
0
0.008
0
0.022
0
0.022
0
0.009
0
0.027
0
0.027
0
0.011
0
0.033
0
0.033
0
0.013
12.0
12.1
DRILLING
12.2
12.3
12.4
12.5
12.6
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
MWE1200SA
MWE1200MA
MWS1200MB
MWS1200LB
MWS1200X8DB
MWE1210SA
MWE1210MA
MWS1210MB
MWS1210LB
MWE1220SA
MWE1220MA
MWS1220MB
MWS1220LB
MWE1230SA
MWE1230MA
MWS1230MB
MWS1230LB
MWE1240SA
MWE1240MA
MWS1240MB
MWS1240LB
MWE1250SA
MWE1250MA
MWS1250MB
MWS1250LB
MWS1250X8DB
MWE1260SA
MWE1260MA
MWS1260MB
MWS1260LB
L2
L1
D4
51
73
51
73
102
121
12.0
12.0
60
60
122
12.0
96
132
96
132
158
194
12.0
12.0
51
76
51
76
102
135
12.1
12.1
62.5 65
100
104
128
167
13.0
13.0
51
76
D1
(mm) (l/d)
12.7
12.8
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
51
76
102
135
12.2
12.2
62.5 65
100
104
128
167
13.0
13.0
51
76
102
135
12.3
12.3
62.5 65
100
104
128
167
13.0
13.0
5 Int.
8 Int.
51
76
102
135
12.4
12.4
2 Ext.
3 Ext.
62.5 65
100
104
128
167
13.0
13.0
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
51
76
51
76
51
76
51
76
102
135
12.5
12.5
62.5
65
128
13.0
100
138
104
143
167
206
13.0
13.0
51
78
51
78
102
137
12.6
12.6
65
104
65
104
128
167
13.0
13.0
12.9
13.0
13.1
13.2
13.3
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
Order Number
MWE1270SA
MWE1270MA
MWS1270MB
MWS1270LB
MWE1280SA
MWE1280MA
MWS1280MB
MWS1280LB
MWE1290SA
MWE1290MA
MWS1290MB
MWS1290LB
MWE1300SA
MWE1300MA
MWS1300MB
MWS1300LB
MWS1300X8DB
MWE1310SA
MWE1310MA
MWS1310MB
MWS1310LB
MWE1320SA
MWE1320MA
MWS1320MB
MWS1320LB
MWE1330SA
MWE1330MA
MWS1330MB
MWS1330LB
L012
L3
L2
L1
D4
51
78
51
78
102
137
12.7
12.7
65
104
65
104
128
167
13.0
13.0
51
78
51
78
102
137
12.8
12.8
65
104
65
104
128
167
13.0
13.0
51
78
51
78
102
137
12.9
12.9
65
104
65
104
128
167
13.0
13.0
51
78
51
78
102
137
13.0
13.0
65
65
128
13.0
104
143
104
143
167
206
13.0
13.0
51
84
51
84
102
144
13.1
13.1
67.5 70
108
112
134
176
14.0
14.0
51
84
102
144
13.2
13.2
67.5 70
108
112
134
176
14.0
14.0
54
84
107
144
13.3
13.3
67.5 70
108
112
134
176
14.0
14.0
51
84
54
84
13.5
13.6
13.7
13.8
13.9
14.0
14.1
14.2
14.3
14.4
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
3 Ext.
3 Int.
5 Int.
3 Ext.
3 Int.
5 Int.
a
a
a
a
a
MWE1340SA
MWE1340MA
MWS1340MB
MWS1340LB
MWE1350SA
MWE1350MA
MWS1350MB
MWS1350LB
MWS1350X8DB
MWE1360SA
MWE1360MA
MWS1360MB
MWS1360LB
MWE1370SA
MWE1370MA
MWS1370MB
MWS1370LB
MWE1380SA
MWE1380MA
MWS1380MB
MWS1380LB
MWE1390SA
MWE1390MA
MWS1390MB
MWS1390LB
MWE1400SA
MWE1400MA
MWS1400MB
MWS1400LB
MWS1400X8DB
MWE1410SA
MWE1410MA
MWS1410MB
MWS1410LB
MWE1420SA
MWE1420MA
MWS1420MB
MWS1420LB
MWE1430MA
MWS1430MB
MWS1430LB
MWE1440MA
MWS1440MB
MWS1440LB
L1
D4
54
84
54
84
107
144
13.4
13.4
67.5 70
108
112
134
176
14.0
14.0
54
84
54
84
107
144
13.5
13.5
67.5
70
134
14.0
112
154
176
218
14.0
14.0
108
149
54
86
54
86
107
147
13.6
13.6
70
112
70
112
134
176
14.0
14.0
54
86
54
86
107
147
13.7
13.7
70
112
70
112
134
176
14.0
14.0
54
86
54
86
107
147
13.8
13.8
70
112
70
112
134
176
14.0
14.0
54
86
54
86
107
147
13.9
13.9
70
112
70
112
134
176
14.0
14.0
54
86
54
86
107
147
14.0
14.0
70
70
134
14.0
112
154
112
154
176
218
14.0
14.0
56
89
56
89
111
151
14.1
14.1
72.5 75
116
120
140
185
15.0
15.0
56
89
111
151
14.2
14.2
72.5 75
116
120
140
185
15.0
15.0
89
89
72.5 75
116
120
151
140
185
14.3
15.0
15.0
56
89
89
89
72.5 75
116
120
151
140
185
14.4
15.0
15.0
D1
(mm) (l/d)
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
3 Ext.
3 Int.
5 Int.
14.6
14.7
3 Ext.
3 Int.
5 Int.
14.8
3 Ext.
3 Int.
5 Int.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
15.3
3 Ext.
3 Int.
5 Int.
15.4
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
15.6
3 Ext.
3 Int.
5 Int.
15.7
3 Ext.
3 Int.
5 Int.
14.5
14.9
15.0
15.1
15.2
15.5
Dimensions (mm)
Stock
VP15TF
L2
Hole Depth
L3
Coolant
(Int./Ext.)
Order Number
Drill
Dia.
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Order Number
MWE1450SA
MWE1450MA
MWS1450MB
MWS1450LB
MWS1450X8DB
MWE1460MA
MWS1460MB
MWS1460LB
MWE1470MA
MWS1470MB
MWS1470LB
MWE1480MA
MWS1480MB
MWS1480LB
MWE1490MA
MWS1490MB
MWS1490LB
MWE1500SA
MWE1500MA
MWS1500MB
MWS1500LB
MWS1500X8DB
MWE1510MA
MWS1510MB
MWS1510LB
MWE1520SA
MWE1520MA
MWS1520MB
MWS1520LB
MWE1530MA
MWS1530MB
MWS1530LB
MWE1540MA
MWS1540MB
MWS1540LB
MWE1550SA
MWE1550MA
MWS1550MB
MWS1550LB
MWS1550X8DB
MWE1560MA
MWS1560MB
MWS1560LB
MWE1570MA
MWS1570MB
MWS1570LB
L3
L2
L1
D4
56
89
56
89
111
151
14.5
14.5
75
140
15.0
116
160
72.5
120
165
185
225
15.0
15.0
91
75
120
91
75
120
153
140
185
14.6
15.0
15.0
91
75
120
91
75
120
153
140
185
14.7
15.0
15.0
91
75
120
91
75
120
153
140
185
14.8
15.0
15.0
91
75
120
91
75
120
153
140
185
14.9
15.0
15.0
56
91
56
91
111
153
15.0
15.0
75
75
140
15.0
120
165
120
165
185
225
15.0
15.0
94
94
77.5 80
124
128
157
145
193
15.1
16.0
16.0
58
94
115
157
15.2
15.2
77.5 80
124
128
145
193
16.0
16.0
94
94
77.5 80
124
128
157
145
193
15.3
16.0
16.0
94
94
77.5 80
124
128
157
145
193
15.4
16.0
16.0
115
157
15.5
15.5
58
94
58
94
77.5
58
94
80
145
16.0
124
171
128
181
193
241
16.0
16.0
96
80
128
96
80
128
160
145
193
15.6
16.0
16.0
96
80
128
96
80
128
160
145
193
15.7
16.0
16.0
CUTTING CONDITIONS
L015
TECHNICAL DATA
N001
DRILLING
13.4
Dimensions (mm)
Stock
VP15TF
Hole Depth
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
L013
a Suitable

MWE/MWS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
D1=3 3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 25

D1 Tolerance
(mm)
D4 Tolerance
METRIC STANDARD
(mm)
MWE
MWS
0
0.014
0
0.014
0
0.006
0
0.018
0
0.018
0
0.008
0
0.022
0
0.022
0
0.009
0
0.027
0
0.027
0
0.011
0
0.033
0
0.033
0
0.013
15.8
15.9
16.0
DRILLING
16.2
16.3
16.5
17.0
17.5
17.8
18.0
3 Ext.
3 Int.
5 Int.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
8 Int.
2 Ext.
2 Ext.
2 Ext.
3 Ext.
a
a
a
a
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
2 Ext.
3 Ext.
3 Int.
5 Int.
MWE1580MA
MWS1580MB
MWS1580LB
MWE1590MA
MWS1590MB
MWS1590LB
MWE1600SA
MWE1600MA
MWS1600MB
MWS1600LB
MWS1600X8DB
MWE1620SA
MWE1630SA
MWE1650SA
MWE1650MA
MWS1650MB
MWS1650LB
MWE1700SA
MWE1700MA
MWS1700MB
MWS1700LB
MWE1750SA
MWE1750MA
MWS1750MB
MWS1750LB
MWE1780SA
MWE1800SA
MWE1800MA
MWS1800MB
MWS1800LB
L2
L1
D4
96
80
128
96
80
128
160
145
193
15.8
16.0
16.0
96
80
128
96
80
128
160
145
193
15.9
16.0
16.0
58
96
58
96
115
160
16.0
16.0
80
80
145
16.0
128
176
128
181
193
241
16.0
16.0
60
60
119
16.2
60
60
119
16.3
60
102
60
102
119
167
16.5
16.5
82.5 85
132
136
150
201
17.0
17.0
60
102
60
102
119
167
17.0
17.0
85
136
85
136
150
201
17.0
17.0
62
102
62
102
123
167
17.5
17.5
87.5 90
140
144
155
209
18.0
18.0
D1
(mm) (l/d)
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
20.5
3 Int.
5 Int.
21.0
3 Int.
5 Int.
21.5
3 Int.
5 Int.
22.0
3 Int.
5 Int.
22.5
3 Int.
5 Int.
18.5
19.0
19.5
20.0
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
62
62
123
17.8
62
102
62
102
123
167
18.0
18.0
23.0
3 Int.
5 Int.
90
144
90
144
155
209
18.0
18.0
23.5
3 Int.
5 Int.
Order Number
MWE1850SA
MWE1850MA
MWS1850MB
MWS1850LB
MWE1900SA
MWE1900MA
MWS1900MB
MWS1900LB
MWE1950SA
MWE1950MA
MWS1950MB
MWS1950LB
MWE2000SA
MWE2000MA
MWS2000MB
MWS2000LB
MWS2050MB
MWS2050LB
MWS2100MB
MWS2100LB
MWS2150MB
MWS2150LB
MWS2200MB
MWS2200LB
MWS2250MB
MWS2250LB
MWS2300MB
MWS2300LB
MWS2350MB
MWS2350LB
L014
L3
L2
L1
D4
64
114
127
179
18.5
18.5
92.5 95
148
152
160
217
19.0
19.0
64
114
64
114
127
179
19.0
19.0
95
152
95
152
160
217
19.0
19.0
66
114
66
114
131
179
19.5
19.5
97.5 100
156
160
165
225
20.0
20.0
66
114
66
114
131
179
20.0
20.0
100
160
100
160
165
225
20.0
20.0
103
166
105
168
176
239
21.0
21.0
105
168
105
168
176
239
21.0
21.0
108
174
110
176
182
248
22.0
22.0
110
176
110
176
182
248
22.0
22.0
113
182
115
184
188
257
23.0
23.0
115
184
115
184
188
257
23.0
23.0
118
190
120
192
194
266
24.0
24.0
64
114
24.0
3 Int.
5 Int.
24.5
3 Int.
5 Int.
MWS2400MB
MWS2400LB
MWS2450MB
MWS2450LB
L2
L1
D4
120
192
120
192
194
266
24.0
24.0
123
198
125
200
200
270
25.0
25.0
D1
(mm) (l/d)
25.0
Dimensions (mm)
Stock
3 Int.
5 Int.
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
Dimensions (mm)
Stock
VP15TF
Hole Depth
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
s
s
Order Number
MWS2500MB
MWS2500LB
L3
L2
L1
D4
125
200
125
200
200
270
25.0
25.0

y MWE (External coolant)
&3.0 &6.0 mm
&.1181" &.2362"
Conditions Cutting Speed
Feed
(SFM)
(IPR)
Hardness
Drill Diameter
Work Material
Mild Steel
Carbon Steel
Alloy Steel
Stainless Steel
Gray Cast Iron

Ductile Cast Iron
Aluminum Alloy
&6.1 &10.0 mm
&.2362" &.3937"
Feed
Cutting Speed
(IPR)
(SFM)
&10.1 &14.0 mm
&.3937" &.5511"
Cutting Speed
Feed
(SFM)
(IPR)
&14.1 &20.0 mm
&.5511" &.7874"
Cutting Speed
Feed
(SFM)
(IPR)
< 180HB
280
.008
280
.010
295
.012
330
.014
(115 330) (.006 .012) (145 390) (.006 .014) (180 390) (.008 .014) (195 425) (.008 .016)
180 280HB
260
.008
295
.010
295
.012
295
.014
(130 310) (.006 .012) (165 390) (.006 .014) (195 425) (.006 .014) (195 425) (.008 .016)
280 350HB
245
.006
260
.008
280
.010
280
.012
(115 260) (.006 .008) (145 375) (.006 .010) (180 375) (.006 .012) (180 375) (.008 .014)
< 200HB
65
.004
(50 100) (.002 .006)
80
.005
(50 100) (.002 .006)
80
.006
(50 100) (.004 .008)
80
.008
(50 100) (.004 .010)
Tensile Strength
230
.010
245
.012
260
.014
280
.016
(130 280) (.006 .012) (165 295) (.008 .014) (165 310) (.008 .016) (180 310) (.012 .018)
< 350MPa
Tensile Strength
210
.008
230
.010
245
.012
260
.014
(115 260) (.006 .010) (145 280) (.006 .012) (145 295) (.008 .014) (165 295) (.008 .016)
< 450MPa
260
.008
295
.010
330
.012
360
.014
(230 295) (.004 .010) (260 330) (.006 .012) (295 360) (.008 .014) (330 390) (.008 .016)
65
(30 80)
.004
(.002 .006)
80
.005
(50 100) (.002 .006)
80
.006
(50 100) (.004 .008)
100
.008
(80 115) (.004 .010)
H Hardened Material
40 60HRC
65
(50 80)
.004
(.002 .006)
80
.005
(50 100) (.002 .006)
80
.006
(50 100) (.004 .008)
100
.008
(50 115) (.004 .010)
&3.0 &6.0 mm
&.1181" &.2362"
Feed
(SFM)
(IPR)
Hardness
Drill Diameter
Work Material
Mild Steel
Carbon Steel
Alloy Steel
Stainless Steel
Gray Cast Iron

Ductile Cast Iron
Aluminum Alloy
&6.1 &10.0 mm
&.2362" &.3937"
Feed
Cutting Speed
(IPR)
(SFM)
&10.1 &14.0 mm
&.3937" &.5511"
Cutting Speed
Feed
(SFM)
(IPR)
&14.1 &25.0 mm
&.5511" &.9843"
Cutting Speed
Feed
(SFM)
(IPR)
< 180HB
360
.008
(160 390) (.006 .012)
430
.010
(260 460) (.008 .014)
490
.012
(300 560) (.008 .016)
520
.014
(330 590) (.008 .016)
180 280HB
300
.008
(160 330) (.006 .012)
360
.010
(230 390) (.008 .014)
430
.010
(260 460) (.008 .016)
460
.012
(330 490) (.008 .016)
280 350HB
260
.008
(130 300) (.006 .010)
300
.010
(200 360) (.006 .012)
360
.010
(230 430) (.006 .014)
390
.012
(300 460) (.006 .014)
200
(70 330)
.004
(.002 .006)
260
.008
(130 390) (.004 .010)
300
.010
(160 390) (.006 .012)
330
.010
(200 390) (.006 .012)
Tensile Strength
330
.010
(230 390) (.006 .012)
< 350MPa
Tensile Strength
210
.008
(115 260) (.006 .010)
< 450MPa
430
.012
(330 460) (.006 .014)
490
.014
(360 520) (.010 .016)
520
.014
(390 560) (.010 .016)
230
.008
(130 300) (.006 .012)
300
.010
(160 360) (.008 .016)
330
.012
(200 360) (.008 .016)
390
.010
(260 490) (.008 .014)
490
.012
(330 560) (.008 .020)
520
.016
(330 560) (.008 .032)
560
.020
(330 590) (.008 .040)
80
.005
(50 100) (.002 .006)
80
.006
(50 100) (.004 .008)
< 200HB

70
(30 80)
.004
(.002 .006)
100
(80 110)
DRILLING
y MWS (Internal coolant)
.008
(.004 .010)
TECHNICAL DATA
N001
L015
MWS DB
a Can
aaa
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
long deep hole drilling for 15-30 x D.

be used with minimum lubricant for steel and cast iron.
a Super
Light Alloy
Heat Resistant
Alloy
.1250< D1< .2344 .2500< D1< .3906 .4062< D1< .5000

D1 Tolerance
(inch)
D4 Tolerance
(inch)
INCH STANDARD
.00130
.00217
0
.00035
.00098
.00169
0
.00031
.00161
.00268
0
.00043
.1250
.1406
.1495
DRILLING
.1562
.1590
.1693
.1719
.1875
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
MWS01250X15DB
01250X20DB
01250X25DB
01250X30DB
01406X15DB
01406X20DB
01406X25DB
01406X30DB
01495X15DB
01495X20DB
01495X25DB
01495X30DB
01562X15DB
01562X20DB
01562X25DB
01562X30DB
01590X15DB
01590X20DB
01590X25DB
01590X30DB
01693X15DB
01693X20DB
01693X25DB
01693X30DB
01719X15DB
01719X20DB
01719X25DB
01719X30DB
01875X15DB
01875X20DB
01875X25DB
01875X30DB
L2
L1
D4
2.480 2.598 4.488 .1575

3.189 3.307 5.197 .1575
3.858 3.976 5.866 .1575
4.567 4.685 6.575 .1575
2.835 2.953 4.843 .1575
3.622 3.740 5.630 .1575
4.409 4.528 6.417 .1575
5.197 5.315 7.205 .1575
2.835 2.953 4.843 .1575
3.622 3.740 5.630 .1575
4.409 4.528 6.417 .1575
5.197 5.315 7.205 .1575
2.835 2.953 4.843 .1575
3.622 3.740 5.630 .1575
4.409 4.528 6.417 .1575
5.197 5.315 7.205 .1575
3.189 3.307 5.276 .1969
4.094 4.213 6.181 .1969
4.961 5.079 7.047 .1969
5.866 5.984 7.953 .1969
3.189 3.307 5.276 .1969
4.094 4.213 6.181 .1969
4.961 5.079 7.047 .1969
5.866 5.984 7.953 .1969
3.189 3.307 5.276 .1969
4.094 4.213 6.181 .1969
4.961 5.079 7.047 .1969
5.866 5.984 7.953 .1969
3.543 3.661 5.630 .1969
4.528 4.646 6.614 .1969
5.512 5.630 7.598 .1969
6.496 6.614 8.583 .1969
D1
(inch) (l/d)
.2031
.2130
.2188
.2344
.2500
.2570
.2656
.2720
Dimensions (inch)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(inch) (l/d)
Dimensions (inch)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
(Note 1) MWS type with & .1969 " or larger diameter has a recess in the shank end face.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
Order Number
MWS02031X15DB
02031X20DB
02031X25DB
02031X30DB
02130X15DB
02130X20DB
02130X25DB
02130X30DB
02188X15DB
02188X20DB
02188X25DB
02188X30DB
02344X15DB
02344X20DB
02344X25DB
02344X30DB
02500X15DB
02500X20DB
02500X25DB
02500X30DB
02570X15DB
02570X20DB
02570X25DB
02570X30DB
02656X15DB
02656X20DB
02656X25DB
02656X30DB
02720X15DB
02720X20DB
02720X25DB
02720X30DB
L016
L3
L2
L1
D4
3.898 4.016 6.063 .2344

5.000 5.118 7.165 .2344
6.063 6.181 8.228 .2344
7.165 7.283 9.331 .2344
3.898 4.016 6.063 .2344
5.000 5.118 7.165 .2344
6.063 6.181 8.228 .2344
7.165 7.283 9.331 .2344
4.252 4.370 6.417 .2344
5.433 5.551 7.598 .2344
6.614 6.732 8.780 .2344
7.795 7.913 9.961 .2344
4.252 4.370 6.417 .2344
5.433 5.551 7.598 .2344
6.614 6.732 8.780 .2344
7.795 7.913 9.961 .2344
4.606 4.724 6.811 .2656
5.906 6.024 8.110 .2656
7.165 7.283 9.370 .2656
8.465 8.583 10.669 .2656
4.961 5.079 7.165 .2656
6.339 6.457 8.543 .2656
7.717 7.835 9.921 .2656
9.094 9.213 11.299 .2656
4.961 5.079 7.165 .2656
6.339 6.457 8.543 .2656
7.717 7.835 9.921 .2656
9.094 9.213 11.299 .2656
4.961 5.079 7.165 .2720
6.339 6.457 8.543 .2720
7.717 7.835 9.921 .2720
9.094 9.213 11.299 .2720
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
20 Int.
25 Int.
30 Int.
15 Int.
.3281 20 Int.
25 Int.
.2812
.2969
.3125
a
a
15 Int.
.3320 20 Int.
25 Int.
15 Int.
.3438 20 Int.
25 Int.
15 Int.
.3594 20 Int.
25 Int.
a
a
a
a
MWS02812X15DB
02812X20DB
02812X25DB
02812X30DB
02969X15DB
02969X20DB
02969X25DB
02969X30DB
03125X15DB
03125X20DB
03125X25DB
03125X30DB
03281X15DB
03281X20DB
03281X25DB
03320X15DB
03320X20DB
03320X25DB
03438X15DB
03438X20DB
03438X25DB
03594X15DB
03594X20DB
03594X25DB
L2
L1
D4
5.315 5.433 7.559 .3125

6.811 6.929 9.055 .3125
8.268 8.386 10.512 .3125
9.764 9.882 12.008 .3125
5.669 5.787 7.913 .3125
7.244 7.362 9.488 .3125
8.819 8.937 11.063 .3125
10.394 10.512 12.638 .3125
5.669 5.787 7.913 .3125
7.244 7.362 9.488 .3125
8.819 8.937 11.063 .3125
10.394 10.512 12.638 .3125
6.024 6.142 8.307 .3438
7.717 7.835 10.000 .3438
9.370 9.488 11.654 .3438
6.024 6.142 8.307 .3438
7.717 7.835 10.000 .3438
9.370 9.488 11.654 .3438
6.378 6.496 8.661 .3438
8.150 8.268 10.433 .3438
9.921 10.039 12.205 .3438
D1
(inch) (l/d)
Dimensions (inch)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
Dimensions (inch)
Stock
VP15TF
Hole Depth
D1
(inch) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
15 Int.
.3680 20 Int.
25 Int.
15 Int.
.3750 20 Int.
25 Int.
15 Int.
.3906 20 Int.
25 Int.
.4062
15 Int.
20 Int.
.4219
15 Int.
20 Int.
.4375
15 Int.
20 Int.
.4531
15 Int.
20 Int.
.4688
15 Int.
20 Int.
.4844 15 Int.
.5000 15 Int.
a
a
a
a
Order Number
MWS03680X15DB
03680X20DB
03680X25DB
03750X15DB
03750X20DB
03750X25DB
03906X15DB
03906X20DB
03906X25DB
04062X15DB
04062X20DB
04219X15DB
04219X20DB
04375X15DB
04375X20DB
04531X15DB
04531X20DB
04688X15DB
04688X20DB
04844X15DB
05000X15DB
L3
L2
L1
D4
6.732 6.850 9.016 .3906

8.622 8.740 10.906 .3906
10.472 10.591 12.756 .3906
7.087 7.205 9.370 .3906
9.055 9.173 11.339 .3906
11.024 11.142 13.307 .3906
7.087 7.205 9.370 .3906
9.055 9.173 11.339 .3906
11.024 11.142 13.307 .3906
7.441 7.559 9.961 .4219
9.528 9.646 12.047 .4219
7.795 7.913 10.315 .4219
9.961 10.079 12.480 .4219
8.150 8.268 10.709 .4688
10.433 10.551 12.992 .4688
8.504 8.622 11.063 .4688
10.866 10.984 13.425 .4688
8.504 8.622 11.063 .4688
10.866 10.984 13.425 .4688
8.858 8.976 11.457 .5000
9.213 9.331 11.811 .5000
6.732 6.850 9.016 .3906

8.622 8.740 10.906 .3906
10.472 10.591 12.756 .3906
Mild Steel
Carbon Steel
Alloy Steel
&.2500" &.3906"
& 6.5 & 10.0 mm
&.4062" &.5000"
& 10.5 & 14.0 mm
Cutting Speed
(SFM)
Feed
(IPR)
Cutting Speed
(SFM)
Feed
(IPR)
< 180HB
300
(160 390)
.008
(.006 .012)
360
(260 460)
.010
(.008 .014)
430
(300 560)
.012
(.008 .016)
180 280HB
260
(160 330)
.008
(.006 .012)
300
(230 390)
.010
(.008 .014)
360
(260 460)
.010
(.008 .016)
280 350HB
230
(130 300)
.008
(.006 .010)
260
(200 360)
.010
(.006 .012)
300
(230 430)
.010
(.006 .014)
160
(70 330)
.004
(.002 .006)
230
(130 390)
.008
(.004 .010)
260
(160 390)
.010
(.006 .012)
Stainless Steel
< 200HB
Gray Cast Iron
Tensile Strength
< 350MPa
300
(230 390)
.010
(.006 .012)
360
(330 460)
.012
(.006 .014)
430
(360 520)
.014
(.010 .016)
Ductile Cast Iron
Tensile Strength
< 450MPa
160
(100 260)
.008
(.006 .010)
200
(130 300)
.008
(.006 .012)
260
(160 360)
.010
(.008 .016)
Aluminum Alloy
330
(260 490)
.010
(.008 .014)
430
(330 560)
.012
(.008 .020)
460
(330 560)
.016
(.008 .032)
70
(30 80)
.004
(.002 .006)
70
(50 100)
.005
(.002 .006)
70
(50 100)
.006
(.004 .008)
HOW TO USE
L025
TECHNICAL DATA
N001
DRILLING
Work Material
&.1250" &.2344"
Drill Diameter
D1
& 3.0 & 6.0 mm
Feed
(SFM)
(IPR)
Hardness
L017
MWS DB
a Can
aaa
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron

a Super
Light Alloy
Heat Resistant
Alloy
D1=3
0.017
0.031
0
0.006
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
3<D1< 6
6<D1< 10 10<D1< 14
0.025
0.043
0
0.008
0.033
0.055
0
0.009
0.041
0.068
0
0.011
3.0
3.1
DRILLING
3.2
3.3
3.4
3.5
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
MWS0300X10DB
0300X15DB
0300X20DB
0300X25DB
0300X30DB
0310X10DB
0310X15DB
0310X20DB
0310X25DB
0310X30DB
0320X10DB
0320X15DB
0320X20DB
0320X25DB
0320X30DB
0330X10DB
0330X15DB
0330X20DB
0330X25DB
0330X30DB
0340X10DB
0340X15DB
0340X20DB
0340X25DB
0340X30DB
0350X10DB
0350X15DB
0350X20DB
0350X25DB
0350X30DB
L2
L1
D4
39
54
42
57
90
105
3.0
3.0
69
72
120
3.0
84
99
87
102
135
150
3.0
3.0
46
63
49
66
97
114
4.0
4.0
D1
(mm) (l/d)
3.6
3.7
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
81
84
132
4.0
20 Int.
98
116
101
119
149
167
4.0
4.0
25 Int.
30 Int.
46
63
49
66
97
114
4.0
4.0
10 Int.
15 Int.
81
84
132
4.0
20 Int.
98
116
101
119
149
167
4.0
4.0
25 Int.
30 Int.
46
63
49
66
97
114
4.0
4.0
10 Int.
15 Int.
3.8
3.9
81
84
132
4.0
20 Int.
98
116
101
119
149
167
4.0
4.0
25 Int.
30 Int.
46
63
49
66
97
114
4.0
4.0
10 Int.
15 Int.
4.0
81
84
132
4.0
20 Int.
98
116
101
119
149
167
4.0
4.0
25 Int.
30 Int.
46
63
49
66
97
114
4.0
4.0
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
81
84
132
4.0
98
116
101
119
149
167
4.0
4.0
4.1
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
(Note 1) MWS type with & 5.0 or larger diameter has a recess in the shank end face.
Order Number
MWS0360X10DB
0360X15DB
0360X20DB
0360X25DB
0360X30DB
0370X10DB
0370X15DB
0370X20DB
0370X25DB
0370X30DB
0380X10DB
0380X15DB
0380X20DB
0380X25DB
0380X30DB
0390X10DB
0390X15DB
0390X20DB
0390X25DB
0390X30DB
0400X10DB
0400X15DB
0400X20DB
0400X25DB
0400X30DB
0410X10DB
0410X15DB
0410X20DB
0410X25DB
0410X30DB
L018
L3
L2
L1
D4
52
72
55
75
103
123
4.0
4.0
92
95
143
4.0
112
132
115
135
163
183
4.0
4.0
52
72
55
75
103
123
4.0
4.0
92
95
143
4.0
112
132
115
135
163
183
4.0
4.0
52
72
55
75
103
123
4.0
4.0
92
95
143
4.0
112
132
115
135
163
183
4.0
4.0
52
72
55
75
103
123
4.0
4.0
92
95
143
4.0
112
132
115
135
163
183
4.0
4.0
52
72
55
75
103
123
4.0
4.0
92
95
143
4.0
112
132
115
135
163
183
4.0
4.0
59
81
62
84
112
134
5.0
5.0
104
107
157
5.0
126
149
129
152
179
202
5.0
5.0
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
MWS0420X10DB
0420X15DB
0420X20DB
0420X25DB
0420X30DB
0430X10DB
0430X15DB
0430X20DB
0430X25DB
0430X30DB
0440X10DB
0440X15DB
0440X20DB
0440X25DB
0440X30DB
0450X10DB
0450X15DB
0450X20DB
0450X25DB
0450X30DB
0460X10DB
0460X15DB
0460X20DB
0460X25DB
0460X30DB
0470X10DB
0470X15DB
0470X20DB
0470X25DB
0470X30DB
0480X10DB
0480X15DB
0480X20DB
0480X25DB
0480X30DB
0490X10DB
0490X15DB
0490X20DB
0490X25DB
0490X30DB
0500X10DB
0500X15DB
0500X20DB
0500X25DB
0500X30DB
L1
D4
59
81
62
84
112
134
5.0
5.0
104
107
157
5.0
126
149
129
152
179
202
5.0
5.0
59
81
62
84
112
134
5.0
5.0
104
107
157
5.0
126
149
129
152
179
202
5.0
5.0
59
81
62
84
112
134
5.0
5.0
104
107
157
5.0
126
149
129
152
179
202
5.0
5.0
59
81
62
84
112
134
5.0
5.0
104
107
157
5.0
126
149
129
152
179
202
5.0
5.0
65
90
68
93
118
143
5.0
5.0
115
118
168
5.0
140
165
143
168
193
218
5.0
5.0
65
90
68
93
118
143
5.0
5.0
115
118
168
5.0
140
165
143
168
193
218
5.0
5.0
65
90
68
93
118
143
5.0
5.0
115
118
168
5.0
140
165
143
168
193
218
5.0
5.0
65
90
68
93
118
143
5.0
5.0
115
118
168
5.0
140
165
143
168
193
218
5.0
5.0
65
90
68
93
118
143
5.0
5.0
115
118
168
5.0
140
165
143
168
193
218
5.0
5.0
D1
(mm) (l/d)
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
Dimensions (mm)
Stock
VP15TF
L2
Hole Depth
L3
Coolant
(Int./Ext.)
Order Number
Drill
Dia.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
Order Number
MWS0510X10DB
0510X15DB
0510X20DB
0510X25DB
0510X30DB
0520X10DB
0520X15DB
0520X20DB
0520X25DB
0520X30DB
0530X10DB
0530X15DB
0530X20DB
0530X25DB
0530X30DB
0540X10DB
0540X15DB
0540X20DB
0540X25DB
0540X30DB
0550X10DB
0550X15DB
0550X20DB
0550X25DB
0550X30DB
0560X10DB
0560X15DB
0560X20DB
0560X25DB
0560X30DB
0570X10DB
0570X15DB
0570X20DB
0570X25DB
0570X30DB
0580X10DB
0580X15DB
0580X20DB
0580X25DB
0580X30DB
0590X10DB
0590X15DB
0590X20DB
0590X25DB
0590X30DB
L3
L2
L1
D4
72
99
75
102
127
154
6.0
6.0
127
130
182
6.0
154
182
157
185
209
237
6.0
6.0
72
99
75
102
127
154
6.0
6.0
127
130
182
6.0
154
182
157
185
209
237
6.0
6.0
72
99
75
102
127
154
6.0
6.0
127
130
182
6.0
154
182
157
185
209
237
6.0
6.0
72
99
75
102
127
154
6.0
6.0
127
130
182
6.0
154
182
157
185
209
237
6.0
6.0
72
99
75
102
127
154
6.0
6.0
127
130
182
6.0
154
182
157
185
209
237
6.0
6.0
78
108
81
111
133
163
6.0
6.0
138
141
193
6.0
168
198
171
201
223
253
6.0
6.0
78
108
81
111
133
163
6.0
6.0
138
141
193
6.0
168
198
171
201
223
253
6.0
6.0
78
108
81
111
133
163
6.0
6.0
138
141
193
6.0
168
198
171
201
223
253
6.0
6.0
78
108
81
111
133
163
6.0
6.0
138
141
193
6.0
168
198
171
201
223
253
6.0
6.0
CUTTING CONDITIONS
L017
HOW TO USE
L025
TECHNICAL DATA
N001
DRILLING
4.2
Dimensions (mm)
Stock
VP15TF
Hole Depth
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
L019
MWS DB
a Can
aaa
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron

a Super
Light Alloy
Heat Resistant
Alloy
D1=3
0.017
0.031
0
0.006
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
3<D1< 6
6<D1< 10 10<D1< 14
0.025
0.043
0
0.008
0.033
0.055
0
0.009
0.041
0.068
0
0.011
6.0
6.1
DRILLING
6.2
6.3
6.4
6.5
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
MWS0600X10DB
0600X15DB
0600X20DB
0600X25DB
0600X30DB
0610X10DB
0610X15DB
0610X20DB
0610X25DB
0610X30DB
0620X10DB
0620X15DB
0620X20DB
0620X25DB
0620X30DB
0630X10DB
0630X15DB
0630X20DB
0630X25DB
0630X30DB
0640X10DB
0640X15DB
0640X20DB
0640X25DB
0640X30DB
0650X10DB
0650X15DB
0650X20DB
0650X25DB
0650X30DB
L2
L1
D4
78
108
81
111
133
163
6.0
6.0
138
141
193
6.0
168
198
171
201
223
253
6.0
6.0
85
117
88
120
141
173
7.0
7.0
150
153
206
7.0
182
215
185
218
238
271
7.0
7.0
85
117
88
120
141
173
7.0
7.0
150
153
206
7.0
182
215
185
218
238
271
7.0
7.0
85
117
88
120
141
173
7.0
7.0
150
153
206
7.0
182
215
185
218
238
271
7.0
7.0
85
117
88
120
141
173
7.0
7.0
150
153
206
7.0
182
215
185
218
238
271
7.0
7.0
85
117
88
120
141
173
7.0
7.0
150
153
206
7.0
182
215
185
218
238
271
7.0
7.0
D1
(mm) (l/d)
6.6
6.7
6.8
6.9
7.0
7.1
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
Order Number
MWS0660X10DB
0660X15DB
0660X20DB
0660X25DB
0660X30DB
0670X10DB
0670X15DB
0670X20DB
0670X25DB
0670X30DB
0680X10DB
0680X15DB
0680X20DB
0680X25DB
0680X30DB
0690X10DB
0690X15DB
0690X20DB
0690X25DB
0690X30DB
0700X10DB
0700X15DB
0700X20DB
0700X25DB
0700X30DB
0710X10DB
0710X15DB
0710X20DB
0710X25DB
0710X30DB
L020
L3
L2
L1
D4
91
126
94
129
147
182
7.0
7.0
161
164
217
7.0
196
231
199
234
252
287
7.0
7.0
91
126
94
129
147
182
7.0
7.0
161
164
217
7.0
196
231
199
234
252
287
7.0
7.0
91
126
94
129
147
182
7.0
7.0
161
164
217
7.0
196
231
199
234
252
287
7.0
7.0
91
126
94
129
147
182
7.0
7.0
161
164
217
7.0
196
231
199
234
252
287
7.0
7.0
91
126
94
129
147
182
7.0
7.0
161
164
217
7.0
196
231
199
234
252
287
7.0
7.0
98
135
101
138
155
192
8.0
8.0
173
176
230
8.0
210
248
213
251
267
305
8.0
8.0
7.3
7.4
7.5
7.6
7.7
7.8
7.9
8.0
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
MWS0720X10DB
0720X15DB
0720X20DB
0720X25DB
0720X30DB
0730X10DB
0730X15DB
0730X20DB
0730X25DB
0730X30DB
0740X10DB
0740X15DB
0740X20DB
0740X25DB
0740X30DB
0750X10DB
0750X15DB
0750X20DB
0750X25DB
0750X30DB
0760X10DB
0760X15DB
0760X20DB
0760X25DB
0760X30DB
0770X10DB
0770X15DB
0770X20DB
0770X25DB
0770X30DB
0780X10DB
0780X15DB
0780X20DB
0780X25DB
0780X30DB
0790X10DB
0790X15DB
0790X20DB
0790X25DB
0790X30DB
0800X10DB
0800X15DB
0800X20DB
0800X25DB
0800X30DB
L1
D4
98
135
101
138
155
192
8.0
8.0
173
176
230
8.0
210
248
213
251
267
305
8.0
8.0
98
135
101
138
155
192
8.0
8.0
173
176
230
8.0
210
248
213
251
267
305
8.0
8.0
98
135
101
138
155
192
8.0
8.0
173
176
230
8.0
210
248
213
251
267
305
8.0
8.0
98
135
101
138
155
192
8.0
8.0
173
176
230
8.0
210
248
213
251
267
305
8.0
8.0
104
144
107
147
161
201
8.0
8.0
184
187
241
8.0
224
264
227
267
281
321
8.0
8.0
104
144
107
147
161
201
8.0
8.0
184
187
241
8.0
224
264
227
267
281
321
8.0
8.0
104
144
107
147
161
201
8.0
8.0
184
187
241
8.0
224
264
227
267
281
321
8.0
8.0
104
144
107
147
161
201
8.0
8.0
184
187
241
8.0
224
264
227
267
281
321
8.0
8.0
104
144
107
147
161
201
8.0
8.0
184
187
241
8.0
224
264
227
267
281
321
8.0
8.0
D1
(mm) (l/d)
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
Dimensions (mm)
Stock
VP15TF
L2
Hole Depth
L3
Coolant
(Int./Ext.)
Order Number
Drill
Dia.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
Order Number
MWS0810X10DB
0810X15DB
0810X20DB
0810X25DB
0810X30DB
0820X10DB
0820X15DB
0820X20DB
0820X25DB
0820X30DB
0830X10DB
0830X15DB
0830X20DB
0830X25DB
0830X30DB
0840X10DB
0840X15DB
0840X20DB
0840X25DB
0840X30DB
0850X10DB
0850X15DB
0850X20DB
0850X25DB
0850X30DB
0860X10DB
0860X15DB
0860X20DB
0860X25DB
0860X30DB
0870X10DB
0870X15DB
0870X20DB
0870X25DB
0870X30DB
0880X10DB
0880X15DB
0880X20DB
0880X25DB
0880X30DB
0890X10DB
0890X15DB
0890X20DB
0890X25DB
0890X30DB
L3
L2
L1
D4
111
153
114
156
169
211
9.0
9.0
196
199
254
9.0
238
281
241
284
296
339
9.0
9.0
111
153
114
156
169
211
9.0
9.0
196
199
254
9.0
238
281
241
284
296
339
9.0
9.0
111
153
114
156
169
211
9.0
9.0
196
199
254
9.0
238
281
241
284
296
339
9.0
9.0
111
153
114
156
169
211
9.0
9.0
196
199
254
9.0
238
281
241
284
296
339
9.0
9.0
111
153
114
156
169
211
9.0
9.0
196
199
254
9.0
238
281
241
284
296
339
9.0
9.0
117
162
120
165
175
220
9.0
9.0
207
210
265
9.0
252
297
255
300
310
355
9.0
9.0
117
162
120
165
175
220
9.0
9.0
207
210
265
9.0
252
297
255
300
310
355
9.0
9.0
117
162
120
165
175
220
9.0
9.0
207
210
265
9.0
252
297
255
300
310
355
9.0
9.0
117
162
120
165
175
220
9.0
9.0
207
210
265
9.0
252
297
255
300
310
355
9.0
9.0
CUTTING CONDITIONS
L017
HOW TO USE
L025
TECHNICAL DATA
N001
DRILLING
7.2
Dimensions (mm)
Stock
VP15TF
Hole Depth
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
L021
MWS DB
a Super
a Can
aaa
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy

Heat Resistant
Alloy
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D1=3
3<D1< 6
0.017
0.031
0
0.006
0.025
0.043
0
0.008
6<D1< 10 10<D1< 14
0.033
0.055
0
0.009
0.041
0.068
0
0.011
9.0
9.1
DRILLING
9.2
9.3
9.4
9.5
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
MWS0900X10DB
0900X15DB
0900X20DB
0900X25DB
0900X30DB
0910X10DB
0910X15DB
0910X20DB
0910X25DB
0910X30DB
0920X10DB
0920X15DB
0920X20DB
0920X25DB
0920X30DB
0930X10DB
0930X15DB
0930X20DB
0930X25DB
0930X30DB
0940X10DB
0940X15DB
0940X20DB
0940X25DB
0940X30DB
0950X10DB
0950X15DB
0950X20DB
0950X25DB
0950X30DB
L2
L1
D4
117
162
120
165
175
220
9.0
9.0
207
210
265
9.0
252
297
255
300
310
355
9.0
9.0
124
171
127
174
182 10.0
229 10.0
219
222
277 10.0
266
314
269
317
324 10.0
372 10.0
124
171
127
174
182 10.0
229 10.0
219
222
277 10.0
266
314
269
317
324 10.0
372 10.0
124
171
127
174
182 10.0
229 10.0
219
222
277 10.0
266
314
269
317
324 10.0
372 10.0
124
171
127
174
219
266
314
D1
(mm) (l/d)
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
10 Int.
15 Int.
20 Int.
25 Int.
30 Int.
182 10.0
229 10.0
10 Int.
15 Int.
222
277 10.0
10.0 20 Int.
269
317
324 10.0
372 10.0
25 Int.
30 Int.
124
171
127
174
182 10.0
229 10.0
10 Int.
15 Int.
219
222
277 10.0
269
317
324 10.0
372 10.0
20 Int.
25 Int.
266
314
9.6
9.7
9.8
9.9
10.1
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
Order Number
MWS0960X10DB
0960X15DB
0960X20DB
0960X25DB
0960X30DB
0970X10DB
0970X15DB
0970X20DB
0970X25DB
0970X30DB
0980X10DB
0980X15DB
0980X20DB
0980X25DB
0980X30DB
0990X10DB
0990X15DB
0990X20DB
0990X25DB
0990X30DB
1000X10DB
1000X15DB
1000X20DB
1000X25DB
1000X30DB
1010X10DB
1010X15DB
1010X20DB
1010X25DB
L022
L3
L2
L1
D4
130
180
133
183
188 10.0
238 10.0
230
233
288 10.0
280
330
283
333
338 10.0
388 10.0
130
180
133
183
188 10.0
238 10.0
230
233
288 10.0
280
330
283
333
338 10.0
388 10.0
130
180
133
183
188 10.0
238 10.0
230
233
288 10.0
280
330
283
333
338 10.0
388 10.0
130
180
133
183
188 10.0
238 10.0
230
233
288 10.0
280
330
283
333
338 10.0
388 10.0
130
180
133
183
188 10.0
238 10.0
230
233
288 10.0
280
330
283
333
338 10.0
388 10.0
137
189
140
192
201 11.0
253 11.0
242
294
245
297
306 11.0
358 11.0
10.3
10.4
10.5
10.6
10.7
10.8
10.9
11.0
11.1
11.2
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
MWS1020X10DB
1020X15DB
1020X20DB
1020X25DB
1030X10DB
1030X15DB
1030X20DB
1030X25DB
1040X10DB
1040X15DB
1040X20DB
1040X25DB
1050X10DB
1050X15DB
1050X20DB
1050X25DB
1060X10DB
1060X15DB
1060X20DB
1060X25DB
1070X10DB
1070X15DB
1070X20DB
1070X25DB
1080X10DB
1080X15DB
1080X20DB
1080X25DB
1090X10DB
1090X15DB
1090X20DB
1090X25DB
1100X10DB
1100X15DB
1100X20DB
1100X25DB
1110X10DB
1110X15DB
1110X20DB
1110X25DB
1120X10DB
1120X15DB
1120X20DB
1120X25DB
L1
D4
137
189
140
192
201 11.0
253 11.0
242
294
245
297
306 11.0
358 11.0
137
189
140
192
201 11.0
253 11.0
242
294
245
297
306 11.0
358 11.0
137
189
140
192
201 11.0
253 11.0
242
294
245
297
306 11.0
358 11.0
137
189
140
192
201 11.0
253 11.0
242
294
245
297
306 11.0
358 11.0
143
198
146
201
207 11.0
262 11.0
253
308
256
311
317 11.0
372 11.0
143
198
146
201
207 11.0
262 11.0
253
308
256
311
317 11.0
372 11.0
143
198
146
201
207 11.0
262 11.0
253
308
256
311
317 11.0
372 11.0
143
198
146
201
207 11.0
262 11.0
253
308
256
311
317 11.0
372 11.0
143
198
146
201
207 11.0
262 11.0
253
308
256
311
317 11.0
372 11.0
150
207
153
210
215 12.0
272 12.0
265
322
268
325
330 12.0
387 12.0
150
207
153
210
215 12.0
272 12.0
265
322
268
325
330 12.0
387 12.0
D1
(mm) (l/d)
11.3
11.4
11.5
11.6
11.7
11.8
11.9
12.0
Dimensions (mm)
Stock
VP15TF
L2
Hole Depth
L3
Coolant
(Int./Ext.)
Order Number
Drill
Dia.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
15 Int.
20 Int.
25 Int.
10 Int.
12.1 15 Int.
20 Int.
10 Int.
12.2 15 Int.
20 Int.
10 Int.
12.3 15 Int.
20 Int.
10 Int.
12.4 15 Int.
20 Int.
r
r
r
r
r
r
Order Number
MWS1130X10DB
1130X15DB
1130X20DB
1130X25DB
1140X10DB
1140X15DB
1140X20DB
1140X25DB
1150X10DB
1150X15DB
1150X20DB
1150X25DB
1160X10DB
1160X15DB
1160X20DB
1160X25DB
1170X10DB
1170X15DB
1170X20DB
1170X25DB
1180X10DB
1180X15DB
1180X20DB
1180X25DB
1190X10DB
1190X15DB
1190X20DB
1190X25DB
1200X10DB
1200X15DB
1200X20DB
1200X25DB
1210X10DB
1210X15DB
1210X20DB
1220X10DB
1220X15DB
1220X20DB
1230X10DB
1230X15DB
1230X20DB
1240X10DB
1240X15DB
1240X20DB
L3
L2
L1
D4
150
207
153
210
215 12.0
272 12.0
265
322
268
325
330 12.0
387 12.0
150
207
153
210
215 12.0
272 12.0
265
322
268
325
330 12.0
387 12.0
150
207
153
210
215 12.0
272 12.0
265
322
268
325
330 12.0
387 12.0
156
216
159
219
221 12.0
281 12.0
276
336
279
339
341 12.0
401 12.0
156
216
159
219
221 12.0
281 12.0
276
336
279
339
341 12.0
401 12.0
156
216
159
219
221 12.0
281 12.0
276
336
279
339
341 12.0
401 12.0
156
216
159
219
221 12.0
281 12.0
276
336
279
339
341 12.0
401 12.0
156
216
159
219
221 12.0
281 12.0
276
336
279
339
341 12.0
401 12.0
163
225
288
166
228
291
229 13.0
291 13.0
354 13.0
163
225
288
166
228
291
229 13.0
291 13.0
354 13.0
163
225
288
166
228
291
229 13.0
291 13.0
354 13.0
163
225
288
166
228
291
229 13.0
291 13.0
354 13.0
CUTTING CONDITIONS
L017
HOW TO USE
L025
TECHNICAL DATA
N001
DRILLING
10.2
Dimensions (mm)
Stock
VP15TF
Hole Depth
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
L023
MWS DB
a Super
a Can
aaa
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy

Heat Resistant
Alloy
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D1=3
3<D1< 6
0.017
0.031
0
0.006
0.025
0.043
0
0.008
6<D1< 10 10<D1< 14
0.033
0.055
0
0.009
0.041
0.068
0
0.011
DRILLING
10 Int.
12.5 15 Int.
20 Int.
10 Int.
12.6 15 Int.
20 Int.
10 Int.
12.7 15 Int.
20 Int.
10 Int.
12.8 15 Int.
20 Int.
10 Int.
12.9 15 Int.
20 Int.
r
r
r
r
r
r
r
r
10 Int.
13.0 15 Int.
20 Int.
10 Int.
13.1 15 Int.
20 Int.
r
r
r
10 Int.
13.2 15 Int.
20 Int.
MWS1250X10DB
1250X15DB
1250X20DB
1260X10DB
1260X15DB
1260X20DB
1270X10DB
1270X15DB
1270X20DB
1280X10DB
1280X15DB
1280X20DB
1290X10DB
1290X15DB
1290X20DB
1300X10DB
1300X15DB
1300X20DB
1310X10DB
1310X15DB
1310X20DB
1320X10DB
1320X15DB
1320X20DB
D4
L3
L2
163
225
288
166
228
291
229 13.0
291 13.0
354 13.0
10 Int.
13.3 15 Int.
20 Int.
169
234
299
172
237
302
235 13.0
300 13.0
365 13.0
10 Int.
13.4 15 Int.
20 Int.
169
234
299
172
237
302
235 13.0
300 13.0
365 13.0
10 Int.
13.5 15 Int.
20 Int.
169
234
299
172
237
302
235 13.0
300 13.0
365 13.0
10 Int.
13.6 15 Int.
20 Int.
169
234
299
172
237
302
235 13.0
300 13.0
365 13.0
10 Int.
13.7 15 Int.
20 Int.
169
234
299
172
237
302
235 13.0
300 13.0
365 13.0
10 Int.
13.8 15 Int.
20 Int.
176
243
311
179
246
314
243 14.0
310 14.0
378 14.0
10 Int.
13.9 15 Int.
20 Int.
176
243
311
179
246
314
243 14.0
310 14.0
378 14.0
10 Int.
14.0 15 Int.
20 Int.
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
L1
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
r
r
s
s
r
r
r
r
r
r
Order Number
MWS1330X10DB
1330X15DB
1330X20DB
1340X10DB
1340X15DB
1340X20DB
1350X10DB
1350X15DB
1350X20DB
1360X10DB
1360X15DB
1360X20DB
1370X10DB
1370X15DB
1370X20DB
1380X10DB
1380X15DB
1380X20DB
1390X10DB
1390X15DB
1390X20DB
1400X10DB
1400X15DB
1400X20DB
L024
L3
L2
L1
D4
176
243
311
179
246
314
243 14.0
310 14.0
378 14.0
176
243
311
179
246
314
243 14.0
310 14.0
378 14.0
176
243
311
179
246
314
243 14.0
310 14.0
378 14.0
182
252
322
185
255
325
249 14.0
319 14.0
389 14.0
182
252
322
185
255
325
249 14.0
319 14.0
389 14.0
182
252
322
185
255
325
249 14.0
319 14.0
389 14.0
182
252
322
185
255
325
249 14.0
319 14.0
389 14.0
182
252
322
185
255
325
249 14.0
319 14.0
389 14.0
y OPERATIONAL GUIDANCE FOR THE MWS...DB DRILL (

.125"-
.500" &
3.0 -
14.0mm)
a Drilling a blind hole
y 2. Initial cutting with the long type drill
y 1. Drilling a pilot hole
z Use a drill with a larger (atter) point angle than the MWS...DB type.
Mitsubishi type MZE, MZS, MWE or MWS drill is recommended.
x Use a drill with the same diameter as the deep hole drill.
c Drill depth : Approx 1D or deeper.
v Ensure a high precision hole is drilled for the pilot.
y 4. Drill retraction
y 3. Drill the deep hole
z Start cutting at the recommended speed and feed with a non-peck

(continuous feed) cycle.
IRREGULAR FACE DRILLING
z Penetrate the pilot hole at a low revolution. (Cutting speed 65-100

SFM, feed rate .008-.012 IPR)
x Stop the long type drill .039-.118 inch short of the pilot hole bottom.
z After drilling, lower the cutting revolution about .039-.079 inch short of
the hole end. (Cutting speed of around 65-100 SFM)
x Retract the drill to the pilot hole depth starting point at a feed rate of
120 inch/min.
c Finally clear the hole at a cutting speed of 65-100 SFM and feed rate of
.008-.012 IPR.
a Drilling and breaking through on irregular faces or angles
y 1. Spot facing
z Machine a at on the irregular face by using an end mill or drill

capable of spot facing. Make the spot face diameter the same size
as the required deep hole diameter.

y 5. Breaking through
z When breaking through, the cutting edge can be damaged.

x A feed rate of .002-.004 IPR is recommended.
z Use a drill with a larger (atter) point angle than the MWS...DB type.
Mitsubishi type MZE, MZS, MWE or MWS drill is recommended.
x Use a drill with the same diameter as the deep hole drill.
v Ensure a high precision hole is drilled for the pilot.
DRILLING
FLAT FACE DRILLING

z Finally clear the hole at a cutting speed of 65-100 SFM.

x Retract the drill to the pilot hole depth starting point at a feed rate of 120
inch/min.
CUTTING CONDITIONS
L017
TECHNICAL DATA
N001
L025
a Excellent
chip disposal.
coolant hole enables high speed machining
(MZS type).
MZE/MZS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
u(only MZE) e(MZE:u)
a Helical
Light Alloy
Heat Resistant
Alloy
(inch)
D4 Tolerance MZE
(inch)
MZS
INCH STANDARD
MZE
.1250< D1< .2344 .2500< D1< .3906 .4062< D1< .7031 .7188< D1< .7812
D1 Tolerance
0
.00071
0
.00047
0
.00031
0
.00087
0
.00059
0
.00035
0
.00106
0
.00071
0
.00043
0
.00130
0
.00083
0
.00051
(External coolant)
MZS (Internal coolant)
2 Ext.
.1250 3 Int.
5 Int.
3 Int.
5 Int.
.1406 2 Ext.
3 Int.
.1495
5 Int.
2 Ext.
5 Int.
3 Int.
.1590
5 Int.
2 Ext.
.1719 3 Int.
5 Int.
2 Ext.
.1875 3 Int.
5 Int.
2 Ext.
.2031 3 Int.
5 Int.
.2165 3 Int.
2 Ext.
.2188 3 Int.
5 Int.
2 Ext.
.2344 3 Int.
5 Int.
.1405
DRILLING
.1562
a
a
a
a
a
a
a
a
a
a
3 Ext.
.2500 3 Int.
5 Int.
MZE01250SA
MZS01250MB
MZS01250LB
MZS01405MB
MZS01405LB
MZE01406SA
MZS01495MB
MZS01495LB
MZE01562SA
MZS01562LB
MZS01590MB
MZS01590LB
MZE01719SA
MZS01719MB
MZS01719LB
MZE01875SA
MZS01875MB
MZS01875LB
MZE02031SA
MZS02031MB
MZS02031LB
MZS02165MB
MZE02188SA
MZS02188MB
MZS02188LB
MZE02344SA
MZS02344MB
MZS02344LB
MZE02500MA
MZS02500MB
MZS02500LB
L2
L1
D4
.703 .703 1.922 .1250

1.102 1.102 2.992 .1575
1.535 1.535 3.425 .1575
1.260 1.260 3.150 .1575
1.732 1.732 3.622 .1575
D1
(inch) (l/d)
3 Ext.
.2570 3 Int.
5 Int.
3 Ext.
.2656 3 Int.
.781 2.047 .1406
5 Int.
1.260 1.260 3.150 .1575

1.732 1.732 3.622 .1575
3 Ext.
.2720 3 Int.
5 Int.
.781
.875 .875 2.188 .1562

1.732 1.732 3.622 .1575
a
a
3 Ext.
1.417 1.417 3.386 .1969

1.969 1.968 3.937 .1969
.2812 3 Int.
5 Int.
.938 .938 2.281 .1719

1.417 1.417 3.386 .1969
1.969 1.968 3.937 .1969
3 Ext.
.2969 3 Int.
5 Int.
1.000 1.000 2.438 .1875

1.575 1.574 3.543 .1969
2.165 2.165 4.134 .1969
3 Ext.
.3125 3 Int.
5 Int.
1.000 1.000 2.438 .2031

1.083 1.181 3.228 .2344
1.732 1.890 3.937 .2344
3 Ext.
.3281 3 Int.
5 Int.
1.083 1.181 3.228 .2344
3 Ext.
.3320 3 Int.
5 Int.
1.125 1.125 2.625 .2188

1.181 1.181 3.228 .2344
1.890 1.890 3.937 .2344
1.125 1.125 2.625 .2344
1.181 1.181 3.228 .2344
1.890 1.890 3.937 .2344
1.625 1.625 3.188 .2500
1.280 1.378 3.465 .2656
2.047 2.205 4.292 .2656
Dimensions (inch)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(inch) (l/d)
Dimensions (inch)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
(Note 1) MZS type larger than & .2031" have a recess in the shank end face.
(Note 2) MZS type can be used for shrink t holders.
a
a
a
a
a
a
a
a
3 Ext.
.3438 3 Int.
5 Int.
3 Ext.
.3594 3 Int.
5 Int.
a
a
a
Order Number
MZE02570MA
MZS02570MB
MZS02570LB
MZE02656MA
MZS02656MB
MZS02656LB
MZE02720MA
MZS02720MB
MZS02720LB
MZE02812MA
MZS02812MB
MZS02812LB
MZE02969MA
MZS02969MB
MZS02969LB
MZE03125MA
MZS03125MB
MZS03125LB
MZE03281MA
MZS03281MB
MZS03281LB
MZE03320MA
MZS03320MB
MZS03320LB
MZE03438MA
MZS03438MB
MZS03438LB
MZE03594MA
MZS03594MB
MZS03594LB
L026
L3
L2
L1
D4
1.688 1.688 3.268 .2570

1.378 1.378 3.465 .2656
2.205 2.205 4.292 .2656
1.688 1.688 3.250 .2656
1.378 1.378 3.465 .2656
2.205 2.205 4.292 .2656
1.688 1.688 3.268 .2720
1.378 1.378 3.465 .2720
2.205 2.205 4.292 .2720
1.750 1.750 3.438 .2812
1.476 1.575 3.701 .3125
2.362 2.520 4.646 .3125
1.875 1.875 3.563 .2969
1.575 1.575 3.701 .3125
2.520 2.520 4.646 .3125
1.875 1.875 3.563 .3125
1.575 1.575 3.701 .3125
2.520 2.520 4.646 .3125
2.063 2.063 3.750 .3281
1.673 1.772 3.937 .3438
2.677 2.835 5.000 .3438
2.087 2.087 3.780 .3320
1.673 1.772 3.937 .3438
2.677 2.835 5.000 .3438
2.188 2.188 3.875 .3438
1.722 1.772 3.937 .3438
2.835 2.835 5.000 .3438
2.281 2.281 4.000 .3594
1.870 1.968 4.173 .3906
2.992 3.150 5.355 .3906
a
a
5 Int.
3 Ext.
.3750 3 Int.
5 Int.
3 Ext.
.3906 3 Int.
5 Int.
a
a
a
a
3 Ext.
.4062 3 Int.
5 Int.
3 Ext.
.4219 3 Int.
5 Int.
3 Ext.
.4375 3 Int.
5 Int.
3 Ext.
.4531 3 Int.
5 Int.
3 Ext.
.4688 3 Int.
5 Int.
3 Ext.
.4844 3 Int.
5 Int.
3 Ext.
.5000 3 Int.
5 Int.
3 Ext.
.5050 3 Int.
5 Int.
3 Ext.
.5118 3 Int.
5 Int.
a
a
a
a
a
a
a
a
a
a
a
a
3 Ext.
.5156 3 Int.
5 Int.
3 Ext.
.5312 3 Int.
5 Int.
a
a
a
MZE03680MA
MZS03680MB
MZS03680LB
MZE03750MA
MZS03750MB
MZS03750LB
MZE03906MA
MZS03906MB
MZS03906LB
MZE04062MA
MZS04062MB
MZS04062LB
MZE04219MA
MZS04219MB
MZS04219LB
MZE04375MA
MZS04375MB
MZS04375LB
MZE04531MA
MZS04531MB
MZS04531LB
MZE04688MA
MZS04688MB
MZS04688LB
MZE04844MA
MZS04844MB
MZS04844LB
MZE05000MA
MZS05000MB
MZS05000LB
MZE05050MA
MZS05050MB
MZS05050LB
MZE05118MA
MZS05118MB
MZS05118LB
MZE05156MA
MZS05156MB
MZS05156LB
MZE05312MA
MZS05312MB
MZS05312LB
L1
D4
2.283 2.283 4.016 .3680

1.870 1.968 4.173 .3906
2.992 3.150 5.355 .3906
D1
(inch) (l/d)
.5469
VP15TF
L2
Hole Depth
L3
3 Int.
5 Int.
a
a
3 Ext.
2.375 2.375 4.125 .3750

1.969 1.968 4.173 .3906
3.150 3.150 5.355 .3906
.5625 3 Int.
5 Int.
3 Ext.
2.375 2.375 4.125 .3906

1.969 1.968 4.173 .3906
3.150 3.150 5.355 .3906
.5781 3 Int.
2.625 2.625 4.406 .4062

2.067 2.165 4.567 .4219
3.307 3.465 5.866 .4219
5 Int.
3 Int.
.5937
5 Int.
3 Int.
5 Int.
.6094
2.688 2.688 4.500 .4219

2.165 2.165 4.567 .4219
3.465 3.465 5.866 .4219
3 Ext.
.6250 3 Int.
5 Int.
2.813 2.813 4.625 .4375

2.264 2.362 4.803 .4688
3.622 3.780 6.221 .4688
3 Ext.
.6330 3 Int.
2.875 2.875 4.750 .4531

2.362 2.362 4.803 .4688
3.780 3.780 6.221 .4688
2.875 2.875 4.750 .4688
2.362 2.362 4.803 .4688
3.780 3.780 6.221 .4688
3.000 3.000 5.313 .4844
2.461 2.559 5.039 .5000
3.937 4.094 6.575 .5000
3.063 3.063 5.375 .5000
2.559 2.559 5.039 .5000
4.094 4.094 6.575 .5000
3.071 3.071 5.394 .5050
2.559 2.559 5.039 .5118
4.094 4.094 6.575 .5118
3.071 3.071 5.394 .5118
2.559 2.559 5.039 .5118
4.094 4.094 6.575 .5118
3.344 3.344 5.688 .5156
2.657 2.756 5.276 .5469
4.250 4.406 6.922 .5469
3.344 3.344 5.688 .5312
2.657 2.756 5.276 .5469
4.250 4.406 6.922 .5469
Dimensions (inch)
Stock
5 Int.
3 Int.
.6406
5 Int.
.6563
3 Int.
5 Int.
.6718
3 Int.
5 Int.
.6875
3 Int.
5 Int.
.7031
3 Int.
5 Int.
.7188
3 Int.
5 Int.
.7344
3 Int.
5 Int.
.7500
3 Int.
5 Int.
.7580
3 Int.
5 Int.
.7656
3 Int.
5 Int.
.7812
3 Int.
5 Int.
Order Number
MZS05469MB
MZS05469LB
MZE05625MA
MZS05625MB
MZS05625LB
MZE05781MA
MZS05781MB
MZS05781LB
MZS05937MB
MZS05937LB
MZS06094MB
MZS06094LB
MZE06250MA
MZS06250MB
MZS06250LB
MZE06330MA
MZS06330MB
MZS06330LB
MZS06406MB
MZS06406LB
MZS06563MB
MZS06563LB
MZS06718MB
MZS06718LB
MZS06875MB
MZS06875LB
MZS07031MB
MZS07031LB
MZS07188MB
MZS07188LB
MZS07344MB
MZS07344LB
MZS07500MB
MZS07500LB
MZS07580MB
MZS07580LB
MZS07656MB
MZS07656LB
MZS07812MB
MZS07812LB
L3
L2
L1
D4
2.756 2.756 5.276 .5469

4.406 4.406 6.922 .5469
3.500 3.500 5.938 .5625
2.854 2.953 5.512 .5781
4.563 4.718 7.281 .5781
3.582 3.582 6.020 .5781
2.953 2.953 5.512 .5781
4.719 4.718 7.281 .5781
3.051 3.150 5.709 .6250
4.875 5.031 7.594 .6250
3.051 3.150 5.709 .6250
4.875 5.031 7.594 .6250
3.780 3.780 6.299 .6250
3.150 3.150 5.709 .6250
5.031 5.031 7.594 .6250
4.016 4.016 6.575 .6330
3.248 3.347 5.906 .6563
5.197 5.354 7.913 .6563
3.248 3.347 5.906 .6563
5.197 5.354 7.913 .6563
3.346 3.347 5.906 .6563
5.354 5.354 7.913 .6563
3.445 3.543 6.102 .7031
5.512 5.669 8.228 .7031
3.445 3.543 6.102 .7031
5.512 5.669 8.228 .7031
3.543 3.543 6.102 .7031
5.669 5.669 8.228 .7031
3.642 3.740 6.299 .7344
5.827 5.984 8.543 .7344
3.740 3.740 6.299 .7344
5.984 5.984 8.543 .7344
3.839 3.937 6.496 .7812
6.142 6.299 8.858 .7812
DRILLING
3 Ext.
.3680 3 Int.
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
Dimensions (inch)
Stock
VP15TF
Hole Depth
D1
(inch) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
3.839 3.937 6.496 .7812

6.142 6.299 8.858 .7812
3.839 3.937 6.496 .7812
6.142 6.299 8.858 .7812
3.937 3.937 6.496 .7812
6.299 6.299 8.858 .7812
CUTTING CONDITIONS
L039
TECHNICAL DATA
N001
L027
a Excellent
chip disposal.
(MZS type).
MZE/MZS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
a Helical
Light Alloy
Heat Resistant
Alloy
(mm)
D4 Tolerance
METRIC STANDARD
MZE
D1=3
D1 Tolerance
(mm)
MZE
MZS
0
0.014
0
0.014
0
0.006
3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 20

0
0.018
0
0.018
0
0.008
0
0.022
0
0.022
0
0.009
0
0.027
0
0.027
0
0.011
0
0.033
0
0.033
0
0.013
(External coolant)
3.0
3.1
DRILLING
3.2
3.3
3.4
3.5
3.6
3.7
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
s
a
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
MZE0300SA
MZE0300MA
MZS0300MB
MZS0300LB
MZE0310SA
MZE0310MA
MZS0310MB
MZS0310LB
MZE0320SA
MZE0320MA
MZS0320MB
MZS0320LB
MZE0330SA
MZE0330MA
MZS0330MB
MZS0330LB
MZE0340SA
MZE0340MA
MZS0340MB
MZS0340LB
MZE0350SA
MZE0350MA
MZS0350MB
MZS0350LB
MZE0360SA
MZE0360MA
MZS0360MB
MZS0360LB
MZE0370SA
MZE0370MA
MZS0370MB
MZS0370LB
L1
D4
16
21
16
21
55
60
3.0
3.0
24
33
24
33
72
81
3.0
3.0
18
24
18
24
55
60
3.1
3.1
28
39
28
39
76
87
4.0
4.0
18
24
18
24
55
60
3.2
3.2
28
39
28
39
76
87
4.0
4.0
18
24
18
24
55
60
3.3
3.3
28
39
28
39
76
87
4.0
4.0
20
24
20
24
55
60
3.4
3.4
28
39
28
39
76
87
4.0
4.0
20
24
20
24
55
60
3.5
3.5
28
39
28
39
76
87
4.0
4.0
20
27
20
27
55
60
3.6
3.6
32
44
32
44
80
92
4.0
4.0
20
27
20
27
55
60
3.7
3.7
32
44
32
44
80
92
4.0
4.0
D1
(mm) (l/d)
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
Coated Carbide
HTi10
L2
s
s
a
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
s
a
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
s
a
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
a
s
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
Coated Carbide
HTi10
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
(Note 1) MZS type larger than & 5.0 have a recess in the shank end face.
s
s
Order Number
MZE0380SA
MZE0380MA
MZS0380MB
MZS0380LB
MZE0390SA
MZE0390MA
MZS0390MB
MZS0390LB
MZE0400SA
MZE0400MA
MZS0400MB
MZS0400LB
MZE0410SA
MZE0410MA
MZS0410MB
MZS0410LB
MZE0420SA
MZE0420MA
MZS0420MB
MZS0420LB
MZE0430SA
MZE0430MA
MZS0430MB
MZS0430LB
MZE0440SA
MZE0440MA
MZS0440MB
MZS0440LB
MZE0450SA
MZE0450MA
MZS0450MB
MZS0450LB
L028
L3
L2
L1
D4
22
27
22
27
55
60
3.8
3.8
32
44
32
44
80
92
4.0
4.0
22
27
22
27
55
60
3.9
3.9
32
44
32
44
80
92
4.0
4.0
22
27
22
27
55
60
4.0
4.0
32
44
32
44
80
92
4.0
4.0
22
29
22
29
55
63
4.1
4.1
36
50
36
50
86
100
5.0
5.0
22
29
22
29
55
63
4.2
4.2
36
50
36
50
86
100
5.0
5.0
24
29
24
29
58
63
4.3
4.3
36
50
36
50
86
100
5.0
5.0
24
29
24
29
58
63
4.4
4.4
36
50
36
50
86
100
5.0
5.0
24
29
24
29
58
63
4.5
4.5
36
50
36
50
86
100
5.0
5.0
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
4.8
3 Int.
5 Int.
4.9
5.0
5.1
5.2
5.3
5.4
5.5
5.6
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
s
a
s
s
a
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
s
a
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
D4
24
32
24
32
58
68
4.6
4.6
40
55
40
55
90
105
5.0
5.0
24
32
24
32
58
68
4.7
4.7
40
55
40
55
90
105
5.0
5.0
26
32
26
32
62
68
4.8
4.8
40
55
40
55
90
105
5.0
5.0
26
32
26
32
62
68
4.9
4.9
40
55
40
55
90
105
5.0
5.0
26
32
26
32
62
68
5.0
5.0
27.5
44
30
48
82
100
6.0
6.0
26
34
26
34
62
72
5.1
5.1
27.5
44
30
48
82
100
6.0
6.0
26
34
26
34
62
72
5.2
5.2
27.5
44
30
48
82
100
6.0
6.0
26
34
26
34
62
72
5.3
5.3
27.5
44
30
48
82
100
6.0
6.0
28
34
28
34
66
72
5.4
5.4
27.5
44
30
48
82
100
6.0
6.0
28
34
28
34
66
72
5.5
5.5
27.5
44
30
48
82
100
6.0
6.0
28
36
28
36
66
74
5.6
5.6
30
48
30
48
82
100
6.0
6.0
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
D1
(mm) (l/d)
5.7
5.8
5.9
6.0
6.1
6.2
6.3
6.4
6.5
6.6
6.7
Order Number
MZE0570SA
MZE0570MA
MZS0570MB
MZS0570LB
MZE0580SA
MZE0580MA
MZS0580MB
MZS0580LB
MZE0590SA
MZE0590MA
MZS0590MB
MZS0590LB
MZE0600SA
MZE0600MA
MZS0600MB
MZS0600LB
MZE0610SA
MZE0610MA
MZS0610MB
MZS0610LB
MZE0620SA
MZE0620MA
MZS0620MB
MZS0620LB
MZE0630SA
MZE0630MA
MZS0630MB
MZS0630LB
MZE0640SA
MZE0640MA
MZS0640MB
MZS0640LB
MZE0650SA
MZE0650MA
MZS0650MB
MZS0650LB
MZE0660SA
MZE0660MA
MZS0660MB
MZS0660LB
MZE0670SA
MZE0670MA
MZS0670MB
MZS0670LB
L3
L2
L1
D4
28
36
28
36
66
74
5.7
5.7
30
48
30
48
82
100
6.0
6.0
28
36
28
36
66
74
5.8
5.8
30
48
30
48
82
100
6.0
6.0
28
36
28
36
66
74
5.9
5.9
30
48
30
48
82
100
6.0
6.0
28
41
28
41
66
81
6.0
6.0
30
48
30
48
82
100
6.0
6.0
31
41
31
41
70
81
6.1
6.1
32.5
52
35
56
88
109
7.0
7.0
31
41
31
41
70
81
6.2
6.2
32.5
52
35
56
88
109
7.0
7.0
31
41
31
41
70
81
6.3
6.3
32.5
52
35
56
88
109
7.0
7.0
31
41
31
41
70
81
6.4
6.4
32.5
52
35
56
88
109
7.0
7.0
31
41
31
41
70
81
6.5
6.5
32.5
52
35
56
88
109
7.0
7.0
31
43
31
43
70
83
6.6
6.6
35
56
35
56
88
109
7.0
7.0
31
43
31
43
70
83
6.7
6.7
35
56
35
56
88
109
7.0
7.0
CUTTING CONDITIONS
L039
TECHNICAL DATA
N001
DRILLING
3 Int.
5 Int.
MZE0460SA
MZE0460MA
MZS0460MB
MZS0460LB
MZE0470SA
MZE0470MA
MZS0470MB
MZS0470LB
MZE0480SA
MZE0480MA
MZS0480MB
MZS0480LB
MZE0490SA
MZE0490MA
MZS0490MB
MZS0490LB
MZE0500SA
MZE0500MA
MZS0500MB
MZS0500LB
MZE0510SA
MZE0510MA
MZS0510MB
MZS0510LB
MZE0520SA
MZE0520MA
MZS0520MB
MZS0520LB
MZE0530SA
MZE0530MA
MZS0530MB
MZS0530LB
MZE0540SA
MZE0540MA
MZS0540MB
MZS0540LB
MZE0550SA
MZE0550MA
MZS0550MB
MZS0550LB
MZE0560SA
MZE0560MA
MZS0560MB
MZS0560LB
L1
HTi10
L2
Dimensions (mm)
Stock
Coated Carbide
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
HTi10
Hole Depth
VP15TF
4.7
Dimensions (mm)
Stock
Coated Carbide
2 Ext.
3 Ext.
D1
(mm) (l/d)
4.6
Coolant
(Int./Ext.)
Drill
Dia.
L029
a Excellent
chip disposal.
(MZS type).
MZE/MZS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
a Helical
Light Alloy
Heat Resistant
Alloy
(mm)
D4 Tolerance
METRIC STANDARD
MZE
D1=3
D1 Tolerance
(mm)
MZE
MZS
0
0.014
0
0.014
0
0.006
3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 20

0
0.018
0
0.018
0
0.008
0
0.022
0
0.022
0
0.009
0
0.027
0
0.027
0
0.011
0
0.033
0
0.033
0
0.013
(External coolant)
3 Int.
5 Int.
2 Ext.
3 Ext.
6.9
3 Int.
5 Int.
2 Ext.
3 Ext.
DRILLING
7.0
3 Int.
5 Int.
2 Ext.
3 Ext.
7.1
3 Int.
5 Int.
2 Ext.
3 Ext.
7.2
3 Int.
5 Int.
2 Ext.
3 Ext.
7.3
3 Int.
5 Int.
2 Ext.
3 Ext.
7.4
3 Int.
5 Int.
2 Ext.
3 Ext.
7.5
3 Int.
5 Int.
MZE0680SA
MZE0680MA
MZS0680MB
MZS0680LB
MZE0690SA
MZE0690MA
MZS0690MB
MZS0690LB
MZE0700SA
MZE0700MA
MZS0700MB
MZS0700LB
MZE0710SA
MZE0710MA
MZS0710MB
MZS0710LB
MZE0720SA
MZE0720MA
MZS0720MB
MZS0720LB
MZE0730SA
MZE0730MA
MZS0730MB
MZS0730LB
MZE0740SA
MZE0740MA
MZS0740MB
MZS0740LB
MZE0750SA
MZE0750MA
MZS0750MB
MZS0750LB
L1
D4
34
43
34
43
74
83
6.8
6.8
35
56
35
56
88
109
7.0
7.0
34
43
34
43
74
83
6.9
6.9
35
56
35
56
88
109
7.0
7.0
34
43
34
43
74
83
7.0
7.0
35
56
35
56
88
109
7.0
7.0
34
45
34
45
74
87
7.1
7.1
37.5
60
40
64
94
118
8.0
8.0
34
45
34
45
74
87
7.2
7.2
37.5
60
40
64
94
118
8.0
8.0
34
45
34
45
74
87
7.3
7.3
37.5
60
40
64
94
118
8.0
8.0
34
45
34
45
74
87
7.4
7.4
37.5
60
40
64
94
118
8.0
8.0
34
45
34
45
74
87
7.5
7.5
37.5
60
40
64
94
118
8.0
8.0
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
D1
(mm) (l/d)
7.6
7.7
7.8
7.9
8.0
8.1
8.2
8.3
Coated Carbide
HTi10
L2
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
HTi10
6.8
Coated Carbide
2 Ext.
3 Ext.
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
Order Number
MZE0760SA
MZE0760MA
MZS0760MB
MZS0760LB
MZE0770SA
MZE0770MA
MZS0770MB
MZS0770LB
MZE0780SA
MZE0780MA
MZS0780MB
MZS0780LB
MZE0790SA
MZE0790MA
MZS0790MB
MZS0790LB
MZE0800SA
MZE0800MA
MZS0800MB
MZS0800LB
MZE0810SA
MZE0810MA
MZS0810MB
MZS0810LB
MZE0820SA
MZE0820MA
MZS0820MB
MZS0820LB
MZE0830SA
MZE0830MA
MZS0830MB
MZS0830LB
L030
L3
L2
L1
D4
37
48
37
48
79
90
7.6
7.6
40
64
40
64
94
118
8.0
8.0
37
48
37
48
79
90
7.7
7.7
40
64
40
64
94
118
8.0
8.0
37
48
37
48
79
90
7.8
7.8
40
64
40
64
94
118
8.0
8.0
37
48
37
48
79
90
7.9
7.9
40
64
40
64
94
118
8.0
8.0
37
48
37
48
79
90
8.0
8.0
40
64
40
64
94
118
8.0
8.0
37
53
37
53
79
96
8.1
8.1
42.5
68
45
72
100
127
9.0
9.0
37
53
37
53
79
96
8.2
8.2
42.5
68
45
72
100
127
9.0
9.0
37
53
37
53
79
96
8.3
8.3
42.5
68
45
72
100
127
9.0
9.0
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
8.6
3 Int.
5 Int.
2 Ext.
3 Ext.
8.7
3 Int.
5 Int.
2 Ext.
3 Ext.
8.8
3 Int.
5 Int.
2 Ext.
3 Ext.
8.9
3 Int.
5 Int.
2 Ext.
3 Ext.
9.0
3 Int.
5 Int.
2 Ext.
3 Ext.
9.1
3 Int.
5 Int.
2 Ext.
3 Ext.
9.2
3 Int.
5 Int.
2 Ext.
3 Ext.
9.3
3 Int.
5 Int.
2 Ext.
3 Ext.
9.4
3 Int.
5 Int.
D4
37
53
37
53
79
96
8.4
8.4
42.5
68
45
72
100
127
9.0
9.0
37
53
37
53
79
96
8.5
8.5
42.5
68
45
72
100
127
9.0
9.0
40
55
40
55
84
98
8.6
8.6
45
72
45
72
100
127
9.0
9.0
40
55
40
55
84
98
8.7
8.7
45
72
45
72
100
127
9.0
9.0
40
55
40
55
84
98
8.8
8.8
45
72
45
72
100
127
9.0
9.0
40
55
40
55
84
98
8.9
8.9
45
72
45
72
100
127
9.0
9.0
40
55
40
55
84
98
9.0
9.0
45
72
45
72
100
127
9.0
9.0
40
58
40
58
84
102
9.1
9.1
47.5
76
50
80
106 10.0
136 10.0
40
58
40
58
84
102
47.5
76
50
80
106 10.0
136 10.0
40
58
40
58
84
102
47.5
76
50
80
106 10.0
136 10.0
40
58
40
58
84
102
47.5
76
50
80
106 10.0
136 10.0
9.2
9.2
9.3
9.3
9.4
9.4
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
D1
(mm) (l/d)
9.5
9.6
9.7
9.8
9.9
10.0
10.1
10.2
10.3
10.4
10.5
Order Number
MZE0950SA
MZE0950MA
MZS0950MB
MZS0950LB
MZE0960SA
MZE0960MA
MZS0960MB
MZS0960LB
MZE0970SA
MZE0970MA
MZS0970MB
MZS0970LB
MZE0980SA
MZE0980MA
MZS0980MB
MZS0980LB
MZE0990SA
MZE0990MA
MZS0990MB
MZS0990LB
MZE1000SA
MZE1000MA
MZS1000MB
MZS1000LB
MZE1010SA
MZE1010MA
MZS1010MB
MZS1010LB
MZE1020SA
MZE1020MA
MZS1020MB
MZS1020LB
MZE1030SA
MZE1030MA
MZS1030MB
MZS1030LB
MZE1040SA
MZE1040MA
MZS1040MB
MZS1040LB
MZE1050SA
MZE1050MA
MZS1050MB
MZS1050LB
L3
L2
L1
D4
40
58
40
58
84
102
47.5
76
50
80
106 10.0
136 10.0
43
60
43
60
89
105
50
80
50
80
106 10.0
136 10.0
43
60
43
60
89
105
50
80
50
80
106 10.0
136 10.0
43
60
43
60
89
105
50
80
50
80
106 10.0
136 10.0
43
60
43
60
89
105
50
80
50
80
106 10.0
136 10.0
43
60
43
60
89 10.0
105 10.0
50
80
50
80
106 10.0
136 10.0
43
66
43
66
89 10.1
112 10.1
52.5
84
55
88
116 11.0
149 11.0
43
66
43
66
89 10.2
112 10.2
52.5
84
55
88
116 11.0
149 11.0
43
66
43
66
89 10.3
112 10.3
52.5
84
55
88
116 11.0
149 11.0
43
66
43
66
89 10.4
112 10.4
52.5
84
55
88
116 11.0
149 11.0
43
66
43
66
89 10.5
112 10.5
52.5
84
55
88
116 11.0
149 11.0
9.5
9.5
9.6
9.6
9.7
9.7
9.8
9.8
9.9
9.9
CUTTING CONDITIONS
L039
TECHNICAL DATA
N001
DRILLING
3 Int.
5 Int.
MZE0840SA
MZE0840MA
MZS0840MB
MZS0840LB
MZE0850SA
MZE0850MA
MZS0850MB
MZS0850LB
MZE0860SA
MZE0860MA
MZS0860MB
MZS0860LB
MZE0870SA
MZE0870MA
MZS0870MB
MZS0870LB
MZE0880SA
MZE0880MA
MZS0880MB
MZS0880LB
MZE0890SA
MZE0890MA
MZS0890MB
MZS0890LB
MZE0900SA
MZE0900MA
MZS0900MB
MZS0900LB
MZE0910SA
MZE0910MA
MZS0910MB
MZS0910LB
MZE0920SA
MZE0920MA
MZS0920MB
MZS0920LB
MZE0930SA
MZE0930MA
MZS0930MB
MZS0930LB
MZE0940SA
MZE0940MA
MZS0940MB
MZS0940LB
L1
HTi10
L2
Dimensions (mm)
Stock
Coated Carbide
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
HTi10
Hole Depth
VP15TF
8.5
Dimensions (mm)
Stock
Coated Carbide
2 Ext.
3 Ext.
D1
(mm) (l/d)
8.4
Coolant
(Int./Ext.)
Drill
Dia.
L031
a Excellent
chip disposal.
(MZS type).
MZE/MZS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
a Helical
Light Alloy
Heat Resistant
Alloy
(mm)
D4 Tolerance
METRIC STANDARD
MZE
D1=3
D1 Tolerance
(mm)
MZE
MZS
0
0.014
0
0.014
0
0.006
3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 20

0
0.018
0
0.018
0
0.008
0
0.022
0
0.022
0
0.009
0
0.027
0
0.027
0
0.011
0
0.033
0
0.033
0
0.013
(External coolant)
3 Int.
5 Int.
2 Ext.
3 Ext.
10.7
3 Int.
5 Int.
2 Ext.
3 Ext.
DRILLING
10.8
3 Int.
5 Int.
2 Ext.
3 Ext.
10.9
3 Int.
5 Int.
2 Ext.
3 Ext.
11.0
3 Int.
5 Int.
2 Ext.
3 Ext.
11.1
3 Int.
5 Int.
2 Ext.
3 Ext.
11.2
3 Int.
5 Int.
2 Ext.
3 Ext.
11.3
3 Int.
5 Int.
MZE1060SA
MZE1060MA
MZS1060MB
MZS1060LB
MZE1070SA
MZE1070MA
MZS1070MB
MZS1070LB
MZE1080SA
MZE1080MA
MZS1080MB
MZS1080LB
MZE1090SA
MZE1090MA
MZS1090MB
MZS1090LB
MZE1100SA
MZE1100MA
MZS1100MB
MZS1100LB
MZE1110SA
MZE1110MA
MZS1110MB
MZS1110LB
MZE1120SA
MZE1120MA
MZS1120MB
MZS1120LB
MZE1130SA
MZE1130MA
MZS1130MB
MZS1130LB
L1
D4
43
68
43
68
89 10.6
114 10.6
55
88
55
88
116 11.0
149 11.0
47
68
47
68
95 10.7
114 10.7
55
88
55
88
116 11.0
149 11.0
47
68
47
68
95 10.8
114 10.8
55
88
55
88
116 11.0
149 11.0
47
68
47
68
95 10.9
114 10.9
55
88
55
88
116 11.0
149 11.0
47
68
47
68
95 11.0
114 11.0
55
88
55
88
116 11.0
149 11.0
47
71
47
71
95 11.1
118 11.1
57.5
92
60
96
122 12.0
158 12.0
47
71
47
71
95 11.2
118 11.2
57.5
92
60
96
122 12.0
158 12.0
47
71
47
71
95 11.3
118 11.3
57.5
92
60
96
122 12.0
158 12.0
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
D1
(mm) (l/d)
11.4
11.5
11.6
11.7
11.8
11.9
12.0
12.1
Coated Carbide
HTi10
L2
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
HTi10
10.6
Coated Carbide
2 Ext.
3 Ext.
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
Order Number
L2
47
47
MZE1140SA
71
MZE1140MA 71
MZS1140MB 57.5 60
92
96
MZS1140LB
47
47
MZE1150SA
71
MZE1150MA 71
MZS1150MB 57.5 60
92
96
MZS1150LB
47
47
MZE1160SA
73
MZE1160MA 73
60
MZS1160MB 60
96
96
MZS1160LB
47
47
MZE1170SA
73
MZE1170MA 73
60
MZS1170MB 60
96
96
MZS1170LB
47
47
MZE1180SA
73
MZE1180MA 73
60
MZS1180MB 60
96
96
MZS1180LB
51
51
MZE1190SA
73
MZE1190MA 73
60
MZS1190MB 60
96
96
MZS1190LB
51
51
MZE1200SA
73
MZE1200MA 73
60
MZS1200MB 60
96
96
MZS1200LB
51
51
MZE1210SA
76
MZE1210MA 76
MZS1210MB 62.5 65
MZS1210LB 100 104
L032
L3
L1
D4
95 11.4
118 11.4
122 12.0
158 12.0
95 11.5
118 11.5
122 12.0
158 12.0
95 11.6
121 11.6
122 12.0
158 12.0
95 11.7
121 11.7
122 12.0
158 12.0
95 11.8
121 11.8
122 12.0
158 12.0
102 11.9
121 11.9
122 12.0
158 12.0
102 12.0
121 12.0
122 12.0
158 12.0
102 12.1
135 12.1
128 13.0
167 13.0
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
12.4
3 Int.
5 Int.
2 Ext.
3 Ext.
12.5
3 Int.
5 Int.
2 Ext.
3 Ext.
12.6
3 Int.
5 Int.
2 Ext.
3 Ext.
12.7
3 Int.
5 Int.
2 Ext.
3 Ext.
12.8
3 Int.
5 Int.
2 Ext.
3 Ext.
12.9
3 Int.
5 Int.
2 Ext.
3 Ext.
13.0
3 Int.
5 Int.
2 Ext.
3 Ext.
13.1
3 Int.
5 Int.
2 Ext.
3 Ext.
13.2
3 Int.
5 Int.
51
76
51
76
102 12.2
135 12.2
62.5 65
100 104
128 13.0
167 13.0
51
76
D4
51
76
102 12.3
135 12.3
62.5 65
100 104
128 13.0
167 13.0
51
76
51
76
102 12.4
135 12.4
62.5 65
100 104
128 13.0
167 13.0
51
76
51
76
102 12.5
135 12.5
62.5 65
100 104
128 13.0
167 13.0
51
78
51
78
102 12.6
137 12.6
65
104
65
104
128 13.0
167 13.0
51
78
51
78
102 12.7
137 12.7
65
104
65
104
128 13.0
167 13.0
51
78
51
78
102 12.8
137 12.8
65
104
65
104
128 13.0
167 13.0
51
78
51
78
102 12.9
137 12.9
65
104
65
104
128 13.0
167 13.0
51
78
51
78
102 13.0
137 13.0
65
104
65
104
128 13.0
167 13.0
51
84
51
84
102 13.1
144 13.1
67.5 70
108 112
134 14.0
176 14.0
51
84
51
84
102 13.2
144 13.2
67.5 70
108 112
134 14.0
176 14.0
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
D1
(mm) (l/d)
13.3
13.4
13.5
13.6
13.7
13.8
13.9
14.0
14.1
14.2
14.3
2 Ext.
3 Ext.
3 Int.
5 Int.
s
s
s
s
s
Order Number
MZE1330SA
MZE1330MA
MZS1330MB
MZS1330LB
MZE1340SA
MZE1340MA
MZS1340MB
MZS1340LB
MZE1350SA
MZE1350MA
MZS1350MB
MZS1350LB
MZE1360SA
MZE1360MA
MZS1360MB
MZS1360LB
MZE1370SA
MZE1370MA
MZS1370MB
MZS1370LB
MZE1380SA
MZE1380MA
MZS1380MB
MZS1380LB
MZE1390SA
MZE1390MA
MZS1390MB
MZS1390LB
MZE1400SA
MZE1400MA
MZS1400MB
MZS1400LB
MZE1410SA
MZE1410MA
MZS1410MB
MZS1410LB
MZE1420SA
MZE1420MA
MZS1420MB
MZS1420LB
MZE1430SA
MZE1430MA
MZS1430MB
MZS1430LB
L3
L2
54
84
54
84
107 13.3
144 13.3
67.5 70
108 112
134 14.0
176 14.0
54
84
L1
D4
54
84
107 13.4
144 13.4
67.5 70
108 112
134 14.0
176 14.0
54
84
54
84
107 13.5
144 13.5
67.5 70
108 112
134 14.0
176 14.0
54
86
54
86
107 13.6
147 13.6
70
112
70
112
134 14.0
176 14.0
54
86
54
86
107 13.7
147 13.7
70
112
70
112
134 14.0
176 14.0
54
86
54
86
107 13.8
147 13.8
70
112
70
112
134 14.0
176 14.0
54
86
54
86
107 13.9
147 13.9
70
112
70
112
134 14.0
176 14.0
54
86
54
86
107 14.0
147 14.0
70
112
70
112
134 14.0
176 14.0
56
89
56
89
111 14.1
151 14.1
72.5 75
116 120
140 15.0
185 15.0
56
89
56
89
111 14.2
151 14.2
72.5 75
116 120
140 15.0
185 15.0
56
89
56
89
111 14.3
151 14.3
72.5 75
116 120
140 15.0
185 15.0
CUTTING CONDITIONS
L039
TECHNICAL DATA
N001
DRILLING
3 Int.
5 Int.
MZE1220SA
MZE1220MA
MZS1220MB
MZS1220LB
MZE1230SA
MZE1230MA
MZS1230MB
MZS1230LB
MZE1240SA
MZE1240MA
MZS1240MB
MZS1240LB
MZE1250SA
MZE1250MA
MZS1250MB
MZS1250LB
MZE1260SA
MZE1260MA
MZS1260MB
MZS1260LB
MZE1270SA
MZE1270MA
MZS1270MB
MZS1270LB
MZE1280SA
MZE1280MA
MZS1280MB
MZS1280LB
MZE1290SA
MZE1290MA
MZS1290MB
MZS1290LB
MZE1300SA
MZE1300MA
MZS1300MB
MZS1300LB
MZE1310SA
MZE1310MA
MZS1310MB
MZS1310LB
MZE1320SA
MZE1320MA
MZS1320MB
MZS1320LB
L1
HTi10
L2
Dimensions (mm)
Stock
Coated Carbide
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
HTi10
Hole Depth
VP15TF
12.3
Dimensions (mm)
Stock
Coated Carbide
2 Ext.
3 Ext.
D1
(mm) (l/d)
12.2
Coolant
(Int./Ext.)
Drill
Dia.
L033
a Excellent
chip disposal.
(MZS type).
MZE/MZS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
a Helical
Light Alloy
Heat Resistant
Alloy
(mm)
D4 Tolerance
METRIC STANDARD
MZE
D1=3
D1 Tolerance
(mm)
MZE
MZS
0
0.014
0
0.014
0
0.006
3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 20

0
0.018
0
0.018
0
0.008
0
0.022
0
0.022
0
0.009
0
0.027
0
0.027
0
0.011
0
0.033
0
0.033
0
0.013
(External coolant)
14.5
DRILLING
14.6
14.7
14.8
14.9
15.0
15.1
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
s
s
s
s
s
s
s
s
s
s
s
s
s
s
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
s
s
s
s
MZE1440SA
MZE1440MA
MZS1440MB
MZS1440LB
MZE1450SA
MZE1450MA
MZS1450MB
MZS1450LB
MZE1460SA
MZE1460MA
MZS1460MB
MZS1460LB
MZE1470SA
MZE1470MA
MZS1470MB
MZS1470LB
MZE1480SA
MZE1480MA
MZS1480MB
MZS1480LB
MZE1490SA
MZE1490MA
MZS1490MB
MZS1490LB
MZE1500SA
MZE1500MA
MZS1500MB
MZS1500LB
MZE1510SA
MZE1510MA
MZS1510MB
MZS1510LB
56
89
56
89
111 14.4
151 14.4
72.5 75
116 120
140 15.0
185 15.0
56
89
L1
D4
56
89
111 14.5
151 14.5
72.5 75
116 120
140 15.0
185 15.0
56
91
56
91
111 14.6
153 14.6
75
120
75
120
140 15.0
185 15.0
56
91
56
91
111 14.7
153 14.7
75
120
75
120
140 15.0
185 15.0
56
91
56
91
111 14.8
153 14.8
75
120
75
120
140 15.0
185 15.0
56
91
56
91
111 14.9
153 14.9
75
120
75
120
140 15.0
185 15.0
56
91
56
91
111 15.0
153 15.0
75
120
75
120
140 15.0
185 15.0
58
94
58
94
115 15.1
157 15.1
77.5 80
124 128
145 16.0
193 16.0
15.2
15.3
15.4
15.5
15.6
15.7
15.8
15.9
Coated Carbide
2 Ext.
3 Ext.
3 Int.
5 Int.
D1
(mm) (l/d)
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
s
s
s
s
s
s
s
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
Dimensions (mm)
Stock
HTi10
L2
Hole Depth
L3
Coolant
(Int./Ext.)
Order Number
Drill
Dia.
VP15TF
14.4
2 Ext.
3 Ext.
Coated Carbide
HTi10
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Order Number
MZE1520SA
MZE1520MA
MZS1520MB
MZS1520LB
MZE1530SA
MZE1530MA
MZS1530MB
MZS1530LB
MZE1540SA
MZE1540MA
MZS1540MB
MZS1540LB
MZE1550SA
MZE1550MA
MZS1550MB
MZS1550LB
MZE1560SA
MZE1560MA
MZS1560MB
MZS1560LB
MZE1570SA
MZE1570MA
MZS1570MB
MZS1570LB
MZE1580SA
MZE1580MA
MZS1580MB
MZS1580LB
MZE1590SA
MZE1590MA
MZS1590MB
MZS1590LB
L034
: Inventory maintained. s : Inventory maintained in Japan. r : Non stock, produced to order only.
L3
L2
58
94
58
94
115 15.2
157 15.2
77.5 80
124 128
145 16.0
193 16.0
58
94
L1
D4
58
94
115 15.3
157 15.3
77.5 80
124 128
145 16.0
193 16.0
58
94
58
94
115 15.4
157 15.4
77.5 80
124 128
145 16.0
193 16.0
58
94
58
94
115 15.5
157 15.5
77.5 80
124 128
145 16.0
193 16.0
58
96
58
96
115 15.6
160 15.6
80
128
80
128
145 16.0
193 16.0
58
96
58
96
115 15.7
160 15.7
80
128
80
128
145 16.0
193 16.0
58
96
58
96
115 15.8
160 15.8
80
128
80
128
145 16.0
193 16.0
58
96
58
96
115 15.9
160 15.9
80
128
80
128
145 16.0
193 16.0
2 Ext.
3 Ext.
16.2
2 Ext.
3 Ext.
16.3
2 Ext.
3 Ext.
16.4
2 Ext.
3 Ext.
r
r
r
r
r
r
r
r
2 Ext.
3 Ext.
3 Int.
5 Int.
s
s
16.6
2 Ext.
3 Ext.
16.7
2 Ext.
3 Ext.
16.8
2 Ext.
3 Ext.
16.9
2 Ext.
3 Ext.
17.0
2 Ext.
3 Ext.
3 Int.
5 Int.
a
a
17.1
2 Ext.
3 Ext.
17.2
2 Ext.
3 Ext.
17.3
2 Ext.
3 Ext.
17.4
2 Ext.
3 Ext.
17.5
2 Ext.
3 Ext.
3 Int.
5 Int.
s
s
17.6
2 Ext.
3 Ext.
17.7
2 Ext.
3 Ext.
L3
L2
58
96
58
96
115 16.0
160 16.0
17.8
2 Ext.
3 Ext.
80
128
80
128
145 16.0
193 16.0
17.9
2 Ext.
3 Ext.
60
102
60
102
119 16.1
167 16.1
60
102
60
102
119 16.2
167 16.2
60
102
60
102
119 16.3
167 16.3
18.1
2 Ext.
3 Ext.
60
102
60
102
119 16.4
167 16.4
18.2
2 Ext.
3 Ext.
60
102
60
102
119 16.5
167 16.5
18.3
2 Ext.
3 Ext.
82.5 85
132 136
150 17.0
201 17.0
18.4
2 Ext.
3 Ext.
60
102
60
102
119 16.6
167 16.6
60
102
60
102
119 16.7
167 16.7
60
102
60
102
119 16.8
167 16.8
18.6
2 Ext.
3 Ext.
60
102
60
102
119 16.9
167 16.9
18.7
2 Ext.
3 Ext.
60
102
60
102
119 17.0
167 17.0
18.8
2 Ext.
3 Ext.
85
136
85
136
150 17.0
201 17.0
18.9
2 Ext.
3 Ext.
62
102
62
102
123 17.1
167 17.1
62
102
62
102
123 17.2
167 17.2
62
102
62
102
123 17.3
167 17.3
19.1
2 Ext.
3 Ext.
62
102
62
102
123 17.4
167 17.4
19.2
2 Ext.
3 Ext.
62
102
62
102
123 17.5
167 17.5
19.3
2 Ext.
3 Ext.
87.5 90
140 144
155 18.0
209 18.0
19.4
2 Ext.
3 Ext.
62
102
62
102
123 17.6
167 17.6
62
102
62
102
123 17.7
167 17.7
D1
(mm) (l/d)
18.0
18.5
19.0
19.5
r
r
r
2 Ext.
3 Ext.
3 Int.
5 Int.
s
s
2 Ext.
3 Ext.
3 Int.
5 Int.
s
s
2 Ext.
3 Ext.
3 Int.
5 Int.
s
s
2 Ext.
3 Ext.
3 Int.
5 Int.
s
s
Order Number
MZE1780SA
MZE1780MA
MZE1790SA
MZE1790MA
MZE1800SA
MZE1800MA
MZS1800MB
MZS1800LB
MZE1810SA
MZE1810MA
MZE1820SA
MZE1820MA
MZE1830SA
MZE1830MA
MZE1840SA
MZE1840MA
MZE1850SA
MZE1850MA
MZS1850MB
MZS1850LB
MZE1860SA
MZE1860MA
MZE1870SA
MZE1870MA
MZE1880SA
MZE1880MA
MZE1890SA
MZE1890MA
MZE1900SA
MZE1900MA
MZS1900MB
MZS1900LB
MZE1910SA
MZE1910MA
MZE1920SA
MZE1920MA
MZE1930SA
MZE1930MA
MZS1930MB
MZS1930LB
MZE1950SA
MZE1950MA
MZS1950MB
MZS1950LB
L3
L2
L1
D4
62
102
62
102
123 17.8
167 17.8
62
102
62
102
123 17.9
167 17.9
62
102
62
102
123 18.0
167 18.0
90
144
90
144
155 18.0
209 18.0
64
114
64
114
127 18.1
179 18.1
64
114
64
114
127 18.2
179 18.2
64
114
64
114
127 18.3
179 18.3
64
114
64
114
127 18.4
179 18.4
64
114
64
114
127 18.5
179 18.5
92.5 95
148 152
160 19.0
217 19.0
64
114
64
114
127 18.6
179 18.6
64
114
64
114
127 18.7
179 18.7
64
114
64
114
127 18.8
179 18.8
64
114
64
114
127 18.9
179 18.9
64
114
64
114
127 19.0
179 19.0
95
152
95
152
160 19.0
217 19.0
66
114
66
114
131 19.1
179 19.1
66
114
66
114
131 19.2
179 19.2
66
114
66
114
131 19.3
179 19.3
97.5 100
156 160
165 20.0
225 20.0
66
114
66
114
131 19.5
179 19.5
97.5 100
156 160
165 20.0
225 20.0
CUTTING CONDITIONS
L039
TECHNICAL DATA
N001
DRILLING
HTi10
3 Int.
5 Int.
MZE1600SA
MZE1600MA
MZS1600MB
MZS1600LB
MZE1610SA
MZE1610MA
MZE1620SA
MZE1620MA
MZE1630SA
MZE1630MA
MZE1640SA
MZE1640MA
MZE1650SA
MZE1650MA
MZS1650MB
MZS1650LB
MZE1660SA
MZE1660MA
MZE1670SA
MZE1670MA
MZE1680SA
MZE1680MA
MZE1690SA
MZE1690MA
MZE1700SA
MZE1700MA
MZS1700MB
MZS1700LB
MZE1710SA
MZE1710MA
MZE1720SA
MZE1720MA
MZE1730SA
MZE1730MA
MZE1740SA
MZE1740MA
MZE1750SA
MZE1750MA
MZS1750MB
MZS1750LB
MZE1760SA
MZE1760MA
MZE1770SA
MZE1770MA
D4
Dimensions (mm)
Stock
Coated Carbide
VP15TF
L1
Hole Depth
HTi10
s
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
VP15TF
Hole Depth
16.1
16.5
Dimensions (mm)
Stock
Coated Carbide
2 Ext.
3 Ext.
D1
(mm) (l/d)
16.0
Coolant
(Int./Ext.)
Drill
Dia.
L035
a Excellent
chip disposal.
(MZS type).
MZE/MZS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
a Helical
Light Alloy
Heat Resistant
Alloy
(mm)
D4 Tolerance
METRIC STANDARD
MZE
D1=3
D1 Tolerance
(mm)
MZE
MZS
0
0.014
0
0.014
0
0.006
3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 20

0
0.018
0
0.018
0
0.008
0
0.022
0
0.022
0
0.009
0
0.027
0
0.027
0
0.011
0
0.033
0
0.033
0
0.013
(External coolant)
19.6
2 Ext.
3 Ext.
19.7
2 Ext.
3 Ext.
19.8
2 Ext.
3 Ext.
MZE1960SA
MZE1960MA
MZE1970SA
MZE1970MA
MZE1980SA
MZE1980MA
D4
66
114
66 131 19.6
114 179 19.6
66
114
66 131 19.7
114 179 19.7
66
114
66 131 19.8
114 179 19.8
D1
(mm) (l/d)
19.9
20.0
Coated Carbide
2 Ext.
3 Ext.
HTi10
L1
VP15TF
L2
Hole Depth
L3
Dimensions (mm)
Stock
r
r
2 Ext.
3 Ext.
3 Int.
5 Int.
s
s
Order Number
MZE1990SA
MZE1990MA
MZE2000SA
MZE2000MA
MZS2000MB
MZS2000LB
DRILLING
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
Coated Carbide
HTi10
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
L036
L3
L2
L1
D4
66
114
66 131 19.9
114 179 19.9
66
114
66 131 20.0
114 179 20.0
100 100
160 160
165 20.0
225 20.0
MZS
a Pre-hole
drilling for metric screw thread.

(MZS type).
a Helical
STEP DRILL
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D1=4.3, 5.1
D1=6.8
D1=8.5
0
0.018
0
0.009
0
0.022
0
0.009
0
0.022
0
0.011
(Note 2) Spot face drilling is not possible (chamfering only).
(Note 3) For metric coarse thread.
D1
(mm)
4.3
5.1
6.8
8.5
Dimensions (mm)
Stock
Hole
Depth
Coolant
(Int./Ext.)
Order Number
Thread
Size
(l/d)
3
3
Int.
Int.
3
3
Int.
Int.
MZS0430MM05
0510MM06
0680MM08
0850MM10
VP15TF
Drill
Dia.
M5
M6
M8
M10
L4
L3
L1
D4
15
18
31
36
84
90
7.0
8.0
24
30
48
60
104
122
10.0
12.0
y CAUTION FOR USE
Chips from chamfer machining tend to

be elongated and may cause jamming.
It is recommended to peck feed to
reduce the length of chips.
Cutting resistance increases on initial

contact with chamfer. Reduce feed at
this point.
The width of the chamfer is C1.0 for M4M6, and C1.5 for M4-M12.
For widths other than those stated
above consultation is needed.
DRILLING
Spot facing as shown above is not

possible. The large diameter section
does not have any back taper. Please
contact us if spot face drill are required.
CUTTING CONDITIONS
L039
TECHNICAL DATA
N001
L037
MZE/MZS
a Excellent
chip disposal.
(MZS type).
a Helical
FOR TUBE SHEET DRILLING
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
.2500< D1< .3906 .4062< D1< .7031 .7188< D1< .7812

D1 Tolerance
D4 Tolerance
(inch)
MZE
0
.00087
0
.00059
0
.00035
(inch)
MZE
MZS
0
.00106
0
.00071
0
.00043
0
.00130
0
.00083
0
.00051
(External coolant)
(Note 1) MZS type larger than & .2031" have a recess in the shank end face.
Dimensions (inch)
Drill Type
MZS Type
L/D=3
MZS Type
L/D=5
DRILLING
MZE Type
L/D=3
L038
Order Number
MZS0970MB
05050MB
06330MB
1700MB
07580MB
MZS0970LB
05050LB
06330LB
1700LB
07580LB
MZE0970MA
05050MA
06330MA
1700MA
VP15TF
Stock
D1
L3
.3810
.5050
50mm
2.559
.6330
3.248
.6990
.7580
85mm
3.839
.3810
.5050
80mm
4.094
.6330
a
a
a
a
a
a
a
L2
L1
D4
106mm
5.039
10mm
.5118
3.347
5.906
.6363
85mm
3.937
150mm
6.496
17mm
.7812
80mm
4.094
136mm
6.575
10mm
.5118
5.197
5.354
7.913
.6363
.6990
.7580
136mm
6.142
136mm
6.299
201mm
8.858
17mm
.7812
.3810
.5050
60mm
3.071
60mm
3.071
105mm
5.394
9.7mm
.5050
.6330
.6690
4.016
102mm
4.016
102mm
6.575
167mm
.6330
17mm
50mm
2.559
Drill diameter and dimensions appear as decimal values for inch drills and in millimeters for metric drills.

y MZE (External coolant)
Work Material
&.2500" &.3906"
& 6.1 & 10.0mm
Cutting Speed
Feed
(SFM)
(IPR)
&.4062" &.5469"
& 10.1 & 14.0mm
Cutting Speed
Feed
(SFM)
(IPR)
&.5625" &.7812"
& 14.1 & 20.0mm
Cutting Speed
Feed
(SFM)
(IPR)
Mild Steel
< 180HB
150
.008
180
.010
215
.012
230
.014
Carbon Steel
Alloy Steel
180 280HB
130
.008
165
.010
195
.012
215
.014
280 350HB
115
.006
150
.008
180
.010
195
.012
65
.004
80
.0048
80
.006
80
.008
165
.010
195
.012
230
.014
230
.016
150
.008
180
.010
215
.012
230
.014
260
.008
295
.010
330
.012
360
.014
M Stainless Steel
K
&.1250" &.2344"
Drill Diameter
D1
& 3.0 & 6.0mm
Feed
(SFM)
(IPR)
Hardness
< 200HB
Strength
Gray Cast Iron Tensile
< 350MPa
Strength
< 450MPa
N Aluminum Alloy
65
.004
80
.005
80
.006
98
.008
H Hardened Steel
40 60HRC
65
.004
80
.0048
80
.006
100
.008
y MZS (Internal coolant)

Work Material
&.2500" &.3906"
& 6.1 & 10.0mm
Cutting Speed
Feed
(SFM)
(IPR)
&.4062" &.5469"
& 10.1 & 14.0mm
Cutting Speed
Feed
(SFM)
(IPR)
&.5625" &.7812"
& 14.1 & 20.0mm
Cutting Speed
Feed
(SFM)
(IPR)
Mild Steel
< 180HB
260
.008
425
.010
460
.012
490
.014
Carbon Steel
Alloy Steel
180 280HB
230
.008
360
.008
395
.010
425
.012
M Stainless Steel
K
&.1250" &.2344"
Drill Diameter
D1
& 3.0 & 6.0mm
Feed
(SFM)
(IPR)
Hardness
280 350HB
195
.006
230
.008
260
.010
295
.012
< 200HB
130
.004
230
.008
260
.010
295
.010
330
.010
425
.012
460
.014
490
.014
Strength
< 350MPa
Strength
< 450MPa
195
.008
230
.008
260
.010
295
.012
N Aluminum Alloy
390
.008
490
.012
525
.016
555
.019
65
.004
80
.005
85
.006
98
.008
REASONABLE COOLANT FLOW AND PRESSURE FOR MZS DRILLS

Flow Rate and Pressure
Flow Rate
Flow Rate
DRILLING
Reasonable Range
Unreasonable Range
inch
Drill Diameter
inch
Drill Diameter
TECHNICAL DATA
N001
L039
a Suitable

a Worlds smallest coolant through solid carbide drill.
MICRO-MWS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
.0200 < D1 < .0390 .0394 < D1 < .1094 D1=.1200

SB
D1 Tolerance
(inch)
INCH STANDARD
LB
XB
y SB Type
D4 Tolerance
(inch)
(For pilot holes)
+ .00035
0
0
.00035
0
.00035
0
.00031
+ .00055
0
+ .00071
0
0
.00055
0
.00031
0
.00071
0
.00031
Type A
Type B
y LB/XB Type
Type A
Type B
1 Int.
5 Int.
12 Int.
1 Int.
.0210 5 Int.
12 Int.
1 Int.
5 Int.
12 Int.
1 Int.
.0240 5 Int.
12 Int.
1 Int.
.0250 5 Int.
12 Int.
1 Int.
.0260 5 Int.
12 Int.
1 Int.
.0280 5 Int.
12 Int.
DRILLING
.0200
.0225
a
a
a
a
a
a
a
a
a
a
a
a
a
a
MWS00200SB
00200LB
00200XB
00210SB
00210LB
00210XB
00225SB
00225LB
00225XB
00240SB
00240LB
00240XB
00250SB
00250LB
00250XB
00260SB
00260LB
00260XB
00280SB
00280LB
00280XB
D4
D1
(inch) (l/d)
.098 .294 1.772 .1250 A

.315 .511 1.850 .1250 A
.630 .826 1.850 .1250 A
1 Int.
5 Int.
12 Int.
.0292
.102 .296 1.772 .1250 A

.315 .509 1.850 .1250 A
.630 .824 1.850 .1250 A
1 Int.
.0310 5 Int.
12 Int.
.114 .306 1.772 .1250 A

.315 .506 1.850 .1250 A
.630 .821 1.850 .1250 A
1 Int.
5 Int.
12 Int.
.0312
.122 .311 1.772 .1250 A

.315 .503 1.850 .1250 A
.630 .818 1.850 .1250 A
1 Int.
.0320 5 Int.
12 Int.
.122 .309 1.772 .1250 A

.315 .502 1.850 .1250 A
.630 .817 1.850 .1250 A
1 Int.
.0330 5 Int.
12 Int.
.134 .319 1.772 .1250 A

.315 .500 1.850 .1250 A
.630 .815 1.850 .1250 A
1 Int.
.0350 5 Int.
12 Int.
.142 .323 1.969 .1250 A

.394 .575 1.969 .1250 A
.787 .968 1.969 .1250 A
1 Int.
.0360 5 Int.
12 Int.
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Order Number
MWS00292SB
00292LB
00292XB
00310SB
00310LB
00310XB
00312SB
00312LB
00312XB
00320SB
00320LB
00320XB
00330SB
00330LB
00330XB
00350SB
00350LB
00350XB
00360SB
00360LB
00360XB
L040
L3
L2
L1
D4
Type
L1
Dimensions (inch)
Stock
VP15TF
L2
Hole Depth
L3
Drill
Dia.
Coolant
(Int./Ext.)
Order Number
Type
D1
(inch) (l/d)
Dimensions (inch)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
(Note) MWS type can be used for shrink t holders.
.142 .320 1.969 .1250 A

.394 .572 1.969 .1250 A
.787 .966 1.969 .1250 A
.154 .329 1.969 .1250 A
.394 .569 1.969 .1250 A
.787 .963 1.969 .1250 A
.154 .329 1.969 .1250 A
.394 .569 1.969 .1250 A
.787 .962 1.969 .1250 A
.161 .335 1.969 .1250 A
.394 .567 1.969 .1250 A
.787 .961 1.969 .1250 A
.161 .333 1.969 .1250 A
.394 .565 1.969 .1250 A
.787 .959 1.969 .1250 A
.173 .341 1.969 .1250 A
.394 .562 1.969 .1250 A
.787 .955 1.969 .1250 A
.181 .347 1.969 .1250 A
.394 .560 1.969 .1250 A
.787 .953 1.969 .1250 A
1 Int.
.0380 5 Int.
12 Int.
1 Int.
5 Int.
12 Int.
1 Int.
12 Int.
1 Int.
.0400
12 Int.
1 Int.
.0410
12 Int.
1 Int.
.0420
12 Int.
1 Int.
.0430
12 Int.
1 Int.
.0465
12 Int.
1 Int.
.0520
12 Int.
1 Int.
.0550
12 Int.
1 Int.
12 Int.
1 Int.
.0625
12 Int.
1 Int.
.0635
12 Int.
.0390
.0394
.0591
a
a
a
a
a
a
MWS00370SB .181 .345 1.969 .1250

00370LB .394 .558 1.969 .1250
00370XB .787 .952 1.969 .1250
00380SB .193 .355 1.969 .1250
00380LB .394 .556 1.969 .1250
00380XB .787 .950 1.969 .1250
00390SB .193 .353 1.969 .1250
00390LB .394 .554 1.969 .1250
00390XB .787 .948 1.969 .1250
00394SB .197 .357 2.165 .1250
00394XB .906 1.065 2.165 .1250
00400SB .197 .355 2.165 .1250
00400XB .906 1.064 2.165 .1250
00410SB .204 .361 2.165 .1250
00410XB .906 1.062 2.165 .1250
00420SB .205 .360 2.165 .1250
00420XB .906 1.060 2.165 .1250
00430SB .213 .366 2.165 .1250
00430XB .906 1.059 2.165 .1250
00465SB .236 .383 2.165 .1250
00465XB .906 1.052 2.165 .1250
00520SB .252 .388 2.165 .1250
00520XB .906 1.042 2.165 .1250
00550SB .276 .406 2.165 .1250
00550XB .906 1.036 2.165 .1250
00591SB .291 .414 2.165 .1250
00591XB .906 1.028 2.165 .1250
00625SB .315 .432 2.677 .1250
00625XB 1.181 1.298 2.677 .1250
00635SB .315 .430 2.677 .1250
00635XB 1.181 1.296 2.677 .1250
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
D1
(inch) (l/d)
.0670
1 Int.
12 Int.
.0700
1 Int.
12 Int.
.0730
1 Int.
12 Int.
.0760
1 Int.
12 Int.
.0785
1 Int.
12 Int.
.0810
1 Int.
12 Int.
.0860
1 Int.
12 Int.
.0890
1 Int.
12 Int.
.0938
1 Int.
12 Int.
.0960
1 Int.
12 Int.
.1010
1 Int.
12 Int.
.1040
1 Int.
12 Int.
.1060
1 Int.
12 Int.
.1094
1 Int.
12 Int.
.1200
1 Int.
12 Int.
Order Number
MWS00670SB
00670XB
00700SB
00700XB
00730SB
00730XB
00760SB
00760XB
00785SB
00785XB
00810SB
00810XB
00860SB
00860XB
00890SB
00890XB
00938SB
00938XB
00960SB
00960XB
01010SB
01010XB
01040SB
01040XB
01060SB
01060XB
01094SB
01094XB
01200SB
01200XB
L3
L2
L1
D4
Type
D4
Dimensions (inch)
Stock
VP15TF
L1
Hole Depth
L2
Coolant
(Int./Ext.)
L3
Type
Order Number
Drill
Dia.
.331 .439 2.677 .1250 A

1.181 1.289 2.677 .1250 A
.354 .457 2.677 .1250 A
1.181 1.284 2.677 .1250 A
.362 .459 2.677 .1250 A
1.181 1.278 2.677 .1250 A
.378 .469 2.677 .1250 A
1.181 1.273 2.677 .1250 A
.394 .480 2.677 .1250 A
1.181 1.268 2.677 .1250 A
.402 .484 2.913 .1250 A
1.496 1.578 2.913 .1250 A
.433 .506 2.913 .1250 A
1.496 1.569 2.913 .1250 A
.441 .508 2.913 .1250 A
1.496 1.563 2.913 .1250 A
.472 .531 2.913 .1250 A
1.496 1.554 2.913 .1250 A
.480 .534 2.913 .1250 A
1.496 1.550 2.913 .1250 A
.496 .541 3.189 .1250 B
1.772 1.772 3.189 .1250 B
.520 .559 3.189 .1250 B
1.772 1.772 3.189 .1250 B
.528 .556 3.189 .1250 B
1.772 1.772 3.189 .1250 B
.551 .581 3.189 .1250 B
1.772 1.772 3.189 .1250 B
.598 .608 3.425 .1250 B
2.047 2.047 3.425 .1250 B
CUTTING CONDITIONS
L047
HOW TO USE
L048
TECHNICAL DATA
N001
DRILLING
1 Int.
5 Int.
12 Int.
.0370
Dimensions (inch)
Stock
VP15TF
Hole Depth
D1
(inch) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
L041
a Suitable

MICRO-MWS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
0.5 < D1<1 1 < D1 < 2.95

D1 Tolerance MWS-SB
(mm)
MWS-LB/XB
D4 Tolerance
METRIC STANDARD
(mm)
y SB Type
+0.009
0
0
0.009
0
0.006
+0.014
0
0
0.014
0
0.006
(For pilot holes)
Type A
Type B
y LB/XB Type
Type A
Type B
1
5
12
Int.
Int.
Int.
1
0.51 5
12
Int.
Int.
Int.
1
0.52 5
12
Int.
Int.
Int.
1
0.53 5
12
Int.
Int.
Int.
1
0.54 5
12
Int.
Int.
Int.
1
5
12
Int.
Int.
Int.
1
0.56 5
12
Int.
Int.
Int.
DRILLING
0.50
0.55
s
s
s
s
s
s
s
s
s
s
s
s
s
s
MWS0050SB
0050LB
0050XB
0051SB
0051LB
0051XB
0052SB
0052LB
0052XB
0053SB
0053LB
0053XB
0054SB
0054LB
0054XB
0055SB
0055LB
0055XB
0056SB
0056LB
0056XB
L1 D4
D1
(mm) (l/d)
2.5 7.2 47 3
8 13
47 3
16 21
47 3
A
A
A
1
5
12
Int.
Int.
Int.
0.57
2.6 7.2 47 3
8 13
47 3
16 21
47 3
A
A
A
1
0.58 5
12
Int.
Int.
Int.
2.6 7.2 47 3
8 13
47 3
16 21
47 3
A
A
A
1
0.59 5
12
Int.
Int.
Int.
2.6 7.2 47 3
8 13
47 3
16 21
47 3
A
A
A
1
0.60 5
12
Int.
Int.
Int.
2.6 7.2 47 3
8 13
47 3
16 21
47 3
A
A
A
1
0.61 5
12
Int.
Int.
Int.
2.6 7.2 47 3
8 13
47 3
16 21
47 3
A
A
A
1
5
12
Int.
Int.
Int.
0.62
2.9 7.5 47 3
8 13
47 3
16 21
47 3
A
A
A
1
0.63 5
12
Int.
Int.
Int.
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Order Number
MWS0057SB
0057LB
0057XB
0058SB
0058LB
0058XB
0059SB
0059LB
0059XB
0060SB
0060LB
0060XB
0061SB
0061LB
0061XB
0062SB
0062LB
0062XB
0063SB
0063LB
0063XB
L042
L3
L2
L1 D4
Type
L2
Dimensions (mm)
Stock
VP15TF
L3
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
Order Number
Type
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
2.9 7.4 47 3
8 13
47 3
16 21
47 3
A
A
A
2.9 7.4 47 3
8 13
47 3
16 21
47 3
A
A
A
2.9 7.4 47 3
8 12
47 3
16 20
47 3
A
A
A
2.9 7.4 47 3
8 12
47 3
16 20
47 3
A
A
A
3.1 7.6 47 3
8 12
47 3
16 20
47 3
A
A
A
3.1 7.5 47 3
8 12
47 3
16 20
47 3
A
A
A
3.1 7.5 47 3
8 12
47 3
16 20
47 3
A
A
A
1
5
12
Int.
Int.
Int.
1
0.66 5
12
Int.
Int.
Int.
1
0.67 5
12
Int.
Int.
Int.
1
0.68 5
12
Int.
Int.
Int.
1
0.69 5
12
Int.
Int.
Int.
1
5
12
Int.
Int.
Int.
1
0.71 5
12
Int.
Int.
Int.
1
5
12
Int.
Int.
Int.
1
0.73 5
12
Int.
Int.
Int.
1
5
12
Int.
Int.
Int.
1
0.75 5
12
Int.
Int.
Int.
1
0.76 5
12
Int.
Int.
Int.
1
0.77 5
12
Int.
Int.
Int.
1
0.78 5
12
Int.
Int.
Int.
1
5
12
Int.
Int.
Int.
0.65
0.70
0.72
0.74
0.79
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
MWS0064SB
0064LB
0064XB
0065SB
0065LB
0065XB
0066SB
0066LB
0066XB
0067SB
0067LB
0067XB
0068SB
0068LB
0068XB
0069SB
0069LB
0069XB
0070SB
0070LB
0070XB
0071SB
0071LB
0071XB
0072SB
0072LB
0072XB
0073SB
0073LB
0073XB
0074SB
0074LB
0074XB
0075SB
0075LB
0075XB
0076SB
0076LB
0076XB
0077SB
0077LB
0077XB
0078SB
0078LB
0078XB
0079SB
0079LB
0079XB
0.80
3.1 7.5 47 3
8 12
47 3
16 20
47 3
A
A
A
0.81
3.4 7.8 47 3
8 12
47 3
16 20
47 3
VP15TF
A
A
A
D1
(mm) (l/d)
Coolant
(Int./Ext.)
3.1 7.5 47 3
8 12
47 3
16 20
47 3
L2
1
5
12
Int.
Int.
Int.
1
5
12
Int.
Int.
Int.
A
A
A
1
0.82 5
12
Int.
Int.
Int.
3.4 7.7 47 3
8 12
47 3
16 20
47 3
A
A
A
1
0.83 5
12
Int.
Int.
Int.
3.4 7.7 47 3
8 12
47 3
16 20
47 3
A
A
A
1
0.84 5
12
Int.
Int.
Int.
3.4 7.7 47 3
8 12
47 3
16 20
47 3
A
A
A
1
0.85 5
12
Int.
Int.
Int.
3.4 7.7 47 3
8 12
47 3
16 20
47 3
A
A
A
1
5
12
Int.
Int.
Int.
0.86
3.6 7.9 50 3
10 14
50 3
20 24
50 3
A
A
A
1
0.87 5
12
Int.
Int.
Int.
3.6 7.9 50 3
10 14
50 3
20 24
50 3
A
A
A
1
5
12
Int.
Int.
Int.
0.88
3.6 7.8 50 3
10 14
50 3
20 24
50 3
A
A
A
1
0.89 5
12
Int.
Int.
Int.
3.6 7.8 50 3
10 14
50 3
20 24
50 3
A
A
A
1
5
12
Int.
Int.
Int.
0.90
3.6 7.8 50 3
10 14
50 3
20 24
50 3
A
A
A
1
0.91 5
12
Int.
Int.
Int.
3.9 8.1 50 3
10 14
50 3
20 24
50 3
A
A
A
1
0.92 5
12
Int.
Int.
Int.
3.9 8.1 50 3
10 14
50 3
20 24
50 3
A
A
A
1
0.93 5
12
Int.
Int.
Int.
3.9 8.0 50 3
10 14
50 3
20 24
50 3
A
A
A
1
0.94 5
12
Int.
Int.
Int.
3.9 8.0 50 3
10 14
50 3
20 24
50 3
A
A
A
1
5
12
Int.
Int.
Int.
0.95
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Order Number
MWS0080SB
0080LB
0080XB
0081SB
0081LB
0081XB
0082SB
0082LB
0082XB
0083SB
0083LB
0083XB
0084SB
0084LB
0084XB
0085SB
0085LB
0085XB
0086SB
0086LB
0086XB
0087SB
0087LB
0087XB
0088SB
0088LB
0088XB
0089SB
0089LB
0089XB
0090SB
0090LB
0090XB
0091SB
0091LB
0091XB
0092SB
0092LB
0092XB
0093SB
0093LB
0093XB
0094SB
0094LB
0094XB
0095SB
0095LB
0095XB
L1 D4
3.9 8.0 50 3
10 14
50 3
20 24
50 3
A
A
A
4.1 8.2 50 3
10 14
50 3
20 24
50 3
A
A
A
4.1 8.2 50 3
10 14
50 3
20 24
50 3
A
A
A
4.1 8.1 50 3
10 14
50 3
20 24
50 3
A
A
A
4.1 8.1 50 3
10 14
50 3
20 24
50 3
A
A
A
4.1 8.1 50 3
10 14
50 3
20 24
50 3
A
A
A
4.4 8.4 50 3
10 14
50 3
20 24
50 3
A
A
A
4.4 8.4 50 3
10 14
50 3
20 24
50 3
A
A
A
4.4 8.4 50 3
10 14
50 3
20 24
50 3
A
A
A
4.4 8.3 50 3
10 14
50 3
20 24
50 3
A
A
A
4.4 8.3 50 3
10 14
50 3
20 24
50 3
A
A
A
4.6 8.5 50 3
10 14
50 3
20 24
50 3
A
A
A
4.6 8.5 50 3
10 14
50 3
20 24
50 3
A
A
A
4.6 8.5 50 3
10 14
50 3
20 24
50 3
A
A
A
4.6 8.4 50 3
10 14
50 3
20 24
50 3
A
A
A
4.6 8.4 50 3
10 14
50 3
20 24
50 3
A
A
A
L3
L2
CUTTING CONDITIONS
L047
HOW TO USE
L048
TECHNICAL DATA
N001
DRILLING
L1 D4
L3
Dimensions (mm)
Stock
Type
Int.
Int.
Int.
Order Number
Drill Hole
Dia. Depth
Type
1
5
12
0.64
Dimensions (mm)
Stock
VP15TF
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill Hole
Dia. Depth
L043
a Suitable

MICRO-MWS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
0.5 < D1<1 1 < D1 < 2.95

MWS-SB
D1 Tolerance
(mm)
METRIC STANDARD
MWS-LB/XB
+0.009
0
0
0.009
MWS-DB
y SB Type
D4 Tolerance
(For pilot holes)
(mm)
0
0.006
+0.014
0
0
0.014
0
0.014
0
0.006
Type A
Type B
y LB/XB Type
Type A
Type B
y DB Type
1
5
12
Int.
Int.
Int.
1
5
12
Int.
Int.
Int.
1
0.98 5
12
Int.
Int.
Int.
1
5
12
Int.
Int.
Int.
1
12
Int.
Int.
20
Int.
25
30
Int.
Int.
1
20
Int.
Int.
25
30
Int.
Int.
DRILLING
0.96
0.97
0.99
1.00
1.05
s
s
s
s
s
s
s
s
MWS0096SB
0096LB
0096XB
0097SB
0097LB
0097XB
0098SB
0098LB
0098XB
0099SB
0099LB
0099XB
0100SB
0100XB
0100X20DB
0100X25DB
0100X30DB
0105SB
0105X20DB
0105X25DB
0105X30DB
L1 D4
4.9 8.7 50 3
10 14
50 3
20 24
50 3
A
A
A
4.9 8.7 50 3
10 14
50 3
20 24
50 3
A
A
A
4.9 8.7 50 3
10 14
50 3
20 24
50 3
A
A
A
4.9 8.7 50 3
10 14
50 3
20 24
50 3
A
A
A
5.0 8.7 55 3
23 27
55 3
A
A
24
28
60 3
28
33
32
37
66 3
72 3
A
A
5.2 8.8 55 3
24 28
60 3
A
A
29
35
A
A
33
38
66 3
72 3
D1
(mm) (l/d)
1.10
1.15
1.20
1.25
1
12
Int.
Int.
20
Int.
25
30
Int.
Int.
1
20
Int.
Int.
25
30
Int.
Int.
1
12
Int.
Int.
20
Int.
25
30
Int.
Int.
1
20
Int.
Int.
25
30
Int.
Int.
Order Number
MWS0110SB
0110XB
0110X20DB
0110X25DB
0110X30DB
0115SB
0115X20DB
0115X25DB
0115X30DB
0120SB
0120XB
0120X20DB
0120X25DB
0120X30DB
0125SB
0125X20DB
0125X25DB
0125X30DB
L044
L3
L2
L1 D4
Type
L2
Dimensions (mm)
Stock
VP15TF
L3
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
Order Number
Type
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
5.4 8.9 55 3
23 27
55 3
A
A
25
29
60 3
31
36
34
40
66 3
72 3
A
A
5.6 9.1 55 3
26 30
60 3
A
A
32
38
66 3
72 3
A
A
6.0 9.4 55 3
23 26
55 3
A
A
28
31
60 3
34
40
37
43
66 3
72 3
A
A
6.2 9.5 55 3
29 32
68 3
A
A
35
41
A
A
36
41
38
45
74 3
82 3
1.40
1.45
1.50
1.55
1.60
1.65
1.70
20 Int.
25 Int.
30 Int.
1 Int.
20 Int.
25 Int.
30 Int.
1 Int.
12 Int.
20 Int.
25 Int.
30 Int.
1 Int.
20 Int.
25 Int.
30 Int.
1 Int.
12 Int.
20 Int.
25 Int.
30 Int.
1 Int.
20 Int.
25 Int.
30 Int.
1 Int.
12 Int.
20 Int.
25 Int.
30 Int.
1 Int.
20 Int.
25 Int.
30 Int.
1 Int.
12 Int.
20 Int.
25 Int.
30 Int.
MWS0130SB
0130XB
0130X20DB
0130X25DB
0130X30DB
0135SB
0135X20DB
0135X25DB
0135X30DB
0140SB
0140XB
0140X20DB
0140X25DB
0140X30DB
0145SB
0145X20DB
0145X25DB
0145X30DB
0150SB
0150XB
0150X20DB
0150X25DB
0150X30DB
0155SB
0155X20DB
0155X25DB
0155X30DB
0160SB
0160XB
0160X20DB
0160X25DB
0160X30DB
0165SB
0165X20DB
0165X25DB
0165X30DB
0170SB
0170XB
0170X20DB
0170X25DB
0170X30DB
6.4 9.6 55 3
23 26
55 3
A
A
30
33
68 3
36
43
40
46
74 3
82 3
A
A
6.6 9.7 55 3
31 34
68 3
A
A
38
45
74 3
82 3
A
A
7.0 10.0 55 3
23 26
55 3
A
A
32
35
68 3
39
46
42
49
74 3
82 3
A
A
7.2 10.1 55 3
33 36
68 3
A
A
41
48
74 3
82 3
A
A
7.4 10.2 55 3
23 26
55 3
A
A
35
37
68 3
42
50
45
52
74 3
82 3
A
A
7.6 10.3 68 3
36 38
78 3
A
A
43
51
86 3
95 3
D1
(mm) (l/d)
VP15TF
L1 D4
Coolant
(Int./Ext.)
L2
Type
L3
1 Int.
20 Int.
25 Int.
30 Int.
1 Int.
12 Int.
20 Int.
25 Int.
30 Int.
1 Int.
20 Int.
25 Int.
30 Int.
1 Int.
12 Int.
20 Int.
25 Int.
30 Int.
1 Int.
20 Int.
25 Int.
30 Int.
1 Int.
12 Int.
20 Int.
A
A
25 Int.
30 Int.
8.0 10.6 68 3
30 33
68 3
A
A
1 Int.
20 Int.
37
39
78 3
45
53
47
55
86 3
95 3
A
A
25 Int.
30 Int.
A
A
1 Int.
12 Int.
8.2 10.7 68 3
38 40
78 3
20 Int.
46
54
86 3
95 3
A
A
25 Int.
30 Int.
8.4 10.8 68 3
30 32
68 3
A
A
1 Int.
20 Int.
39
42
78 3
50
59
86 3
95 3
A
A
25 Int.
30 Int.
48
56
41
48
43
51
46
54
49
57
1.75
1.80
1.85
1.90
1.95
2.00
2.05
2.10
2.15
Dimensions (mm)
Stock
Order Number
MWS0175SB
0175X20DB
0175X25DB
0175X30DB
0180SB
0180XB
0180X20DB
0180X25DB
0180X30DB
0185SB
0185X20DB
0185X25DB
0185X30DB
0190SB
0190XB
0190X20DB
0190X25DB
0190X30DB
0195SB
0195X20DB
0195X25DB
0195X30DB
0200SB
0200XB
0200X20DB
0200X25DB
0200X30DB
0205SB
0205X20DB
0205X25DB
0205X30DB
0210SB
0210XB
0210X20DB
0210X25DB
0210X30DB
0215SB
0215X20DB
0215X25DB
0215X30DB
L1 D4
68 3
84 3
A
A
94 3
102 3
A
A
9.0 11.2
30 32
68 3
68 3
A
A
41
44
84 3
50
59
53
62
94 3
102 3
A
A
68 3
84 3
A
A
94 3
102 3
A
A
9.4 11.5
30 32
68 3
68 3
A
A
44
46
84 3
53
63
55
65
94 3
102 3
A
A
68 3
84 3
A
A
94 3
102 3
A
A
10.0 11.9
30 32
68 3
68 3
A
A
46
48
84 3
56
66
58
68
94 3
102 3
A
A
74 3
94 3
A
A
107 3
118 3
A
A
74 3
74 3
A
A
L3
L2
8.6 10.9
40 43
49
58
51
60
9.2 11.3
43 45
52
61
54
63
9.6 11.6
45 47
55
64
57
66
10.2 12.0
47 49
57
68
59
69
10.4 12.1
38 40
48
50
94 3
59
69
60
71
107 3
118 3
A
A
74 3
94 3
A
A
107 3
118 3
A
A
10.6 12.2
49 51
60
71
62
73
CUTTING CONDITIONS
L047
HOW TO USE
L048
TECHNICAL DATA
N001
DRILLING
1.35
1 Int.
12 Int.
Order Number
Drill Hole
Dia. Depth
Type
1.30
Dimensions (mm)
Stock
VP15TF
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill Hole
Dia. Depth
L045
a Suitable

MICRO-MWS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
0.5 < D1<1 1 < D1 < 2.95

MWS-SB
D1 Tolerance MWS-LB/XB
(mm)
METRIC STANDARD
+0.009
0
0
0.009
MWS-DB
y SB Type
D4 Tolerance
(For pilot holes)
(mm)
0
0.006
+0.014
0
0
0.014
0
0.014
0
0.006
Type A
Type B
y LB/XB Type
Type A
Type B
y DB Type
2.25
2.30
2.35
Int.
Int.
20
Int.
25
30
Int.
Int.
1
20
Int.
Int.
25
30
Int.
Int.
1
12
Int.
Int.
20
Int.
25
30
Int.
Int.
1
20
Int.
Int.
25
30
Int.
Int.
MWS0220SB
0220XB
0220X20DB
0220X25DB
0220X30DB
0225SB
0225X20DB
0225X25DB
0225X30DB
0230SB
0230XB
0230X20DB
0230X25DB
0230X30DB
0235SB
0235X20DB
0235X25DB
0235X30DB
74 3
74 3
A
A
51
52
94 3
62
73
63
74
107 3
118 3
D1
(mm) (l/d)
1
12
Int.
Int.
20
Int.
A
A
25
30
Int.
Int.
74 3
94 3
A
A
1
20
Int.
Int.
107 3
118 3
A
A
25
30
Int.
Int.
11.4 12.7
38 39
74 3
74 3
A
A
1
12
Int.
Int.
53
54
94 3
20
Int.
64
76
66
77
107 3
118 3
A
A
25
30
Int.
Int.
74 3
94 3
A
A
1
20
Int.
Int.
107 3
118 3
A
A
25
30
Int.
Int.
11.2 12.6
52 53
63
74
64
76
11.6 12.8
54 55
66
78
67
79
2.40
2.45
2.50
2.55
Dimensions (mm)
Stock
VP15TF
11.0 12.5
38 39
L2
Coolant
(Int./Ext.)
L1 D4
L3
Drill Hole
Dia. Depth
Order Number
MWS0240SB
0240XB
0240X20DB
0240X25DB
0240X30DB
0245SB
0245X20DB
0245X25DB
0245X30DB
0250SB
0250XB
0250X20DB
0250X25DB
0250X30DB
0255SB
0255X20DB
0255X25DB
0255X30DB
L046
L1 D4
Type
DRILLING
2.20
1
12
Order Number
Type
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
12.0 13.1
38 39
74 3
74 3
A
A
55
56
94 3
67
79
68
80
107 3
118 3
A
A
74 3
94 3
A
A
107 3
118 3
A
A
74 3
74 3
A
A
L3
L2
12.2 13.2
56 57
69
81
70
82
12.4 13.3
38 39
58
59
94 3
70
83
71
84
107 3
118 3
A
A
12.6 12.6 81 3
59 59 103 3
B
B
71
84
B
B
71
84
117 3
132 3
2.65
2.70
2.75
20 Int.
25 Int.
30 Int.
1 Int.
20 Int.
25 Int.
30 Int.
1 Int.
12 Int.
20 Int.
25 Int.
30 Int.
1 Int.
20 Int.
25 Int.
30 Int.
MWS0260SB
0260XB
0260X20DB
0260X25DB
0260X30DB
0265SB
0265X20DB
0265X25DB
0265X30DB
0270SB
0270XB
0270X20DB
0270X25DB
0270X30DB
0275SB
0275X20DB
0275X25DB
0275X30DB
13.0 13.0
45 45
L1 D4
81 3
81 3
B
B
D1
(mm) (l/d)
2.80
1 Int.
12 Int.
s
s
60
60
103 3
20 Int.
73
86
73
86
117 3
132 3
B
B
25 Int.
30 Int.
13.2 13.2 81 3
61 61 103 3
B
B
1 Int.
20 Int.
74
87
117 3
132 3
B
B
25 Int.
30 Int.
81 3
81 3
B
B
1 Int.
12 Int.
74
87
13.4 13.4
45 45
2.85
2.90
62
62
103 3
20 Int.
76
89
76
89
117 3
132 3
B
B
25 Int.
30 Int.
13.6 13.6 81 3
63 63 103 3
B
B
1 Int.
20 Int.
77
91
B
B
25 Int.
30 Int.
77
91
117 3
132 3
2.95
Dimensions (mm)
Stock
VP15TF
L2
Coolant
(Int./Ext.)
L3
Drill Hole
Dia. Depth
Order Number
MWS0280SB
0280XB
0280X20DB
0280X25DB
0280X30DB
0285SB
0285X20DB
0285X25DB
0285X30DB
0290SB
0290XB
0290X20DB
0290X25DB
0290X30DB
0295SB
0295X20DB
0295X25DB
0295X30DB
L3
L2
14.0 14.0
45 45
L1 D4
Type
1 Int.
12 Int.
Order Number
Type
2.60
Dimensions (mm)
Stock
VP15TF
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill Hole
Dia. Depth
81 3
81 3
B
B
64
64
103 3
78
92
78
92
117 3
132 3
B
B
14.2 14.2 81 3
66 66 103 3
B
B
80
94
117 3
132 3
B
B
81 3
81 3
B
B
80
94
14.4 14.4
45 45
67
67
103 3
81
96
81
96
117 3
132 3
B
B
14.6 14.6 81 3
68 68 103 3
B
B
83
97
B
B
83
97
117 3
132 3

y SB/LB/XB Type Drill
Mild Steel
Carbon Steel
Alloy Steel
Stainless Steel
Gray Cast Iron

Ductile Cast Iron
& .0280" & .0335"

& 0.71 & 0.85 mm
Cutting Speed
(SFM)
Feed
(IPR)
& .0339" & .0390"

& 0.86 & 0.99 mm
Cutting Speed
(SFM)
Feed
(IPR)
& .0394" & .1161"

& 1.0 & 2.95 mm
Cutting Speed
(SFM)
Feed
(IPR)
165
.0004
(130 200) (.0002 .0006)
165
.0008
165
.0012
(130 200) (.0004 .0012) (130 200) (.0008 .0020)
200
(165 230)
.0031
(.0016 .0047)
165
.0004
(130 200) (.0002 .0006)
165
.0004
(130 200) (.0002 .0006)
165
.0008
165
.0012
(130 200) (.0004 .0012) (130 200) (.0008 .0020)
165
.0008
165
.0012
(130 200) (.0004 .0012) (130 200) (.0008 .0020)
200
(165 230)
165
(130 200)
.0031
(.0016 .0047)
.0031
(.0016 .0047)
100
(65 130)
100
(65 130)
.0008
(.0004 .0012)
100
(65 130)
.0020
(.0008 .0039)
165
.0006
Tensile Strength
(130 200) (.0003 .0008)
< 350MPa
100
.0004
Tensile Strength
(65 130) (.0002 .0006)
< 450MPa
165
.0008
165
.0016
(130 200) (.0004 .0012) (130 200) (.0008 .0024)
100
.0008
100
.0012
(65 130) (.0004 .0012) (65 130) (.0008 .0020)
165
(130 200)
100
(65 130)
.0032
(.0016 .0047)
.0024
(.0008 .0039)
200
.0012
(165 260) (.0008 .0020)
200
.0016
200
.0024
(165 260) (.0012 .0024) (165 260) (.0016 .0032)
200
(165 260)
.0039
(.0020 .0059)
35
(15 50)
.0012
(.0004 .0020)
< 180HB
180 280HB
280 350HB
< 200HB
Aluminum Alloy
35
(15 50)
.0003
(.0002 .0004)
.00025
(.00015 .0003)
35
(15 50)
.0006
(.0003 .0008)
.0004
(.0002 .0008)
100
(65 130)
35
(15 50)
.0004
(.0002 .0008)
DRILLING
Work Material
& .0197" & .0276"

Drill Diameter
& 0.50 & 0.70 mm
D1
Feed
(SFM)
(IPR)
Hardness
y DB Type Long Drill

Work Material
Mild Steel
Carbon Steel
Alloy Steel
Stainless Steel
Gray Cast Iron

Ductile Cast Iron
& .0394 " & .0787"

Drill Diameter
& 1.0 & 2.0 mm
D1
Feed
(SFM)
(IPR)
Hardness
< 180HB
180 280HB
280 350HB
< 200HB
Cutting Speed
(SFM)
Feed
(IPR)
165
.0031
(130 200) (.0016 .0039)
200
.0039
(165 230) (.0031 .0047)
130
.0028
(100 165) (.0016 .0031)
100
.0016
(65 130) (.0012 .0024)
165
.0035
(130 200) (.0024 .0047)
165
.0028
(130 200) (.0020 .0039)
100
(65 130)
100
(65 130)
.0012
(.0004 .0020)
130
.0028
Tensile Strength
(100 165) (.0016 .0031)
< 350MPa
100
.0016
Tensile Strength
(65 130) (.0012 .0024)
< 450MPa
& .0807" & .1161"

& 2.05 & 2.95 mm
30
(15 50)
.0008
(.0004 .0012)
.0024
(.0016 .0031)
165
.0035
(130 200) (.0024 .0047)
165
.0028
(130 200) (.0020 .0039)
50
(30 65)
.0012
(.0004 .0020)
HOW TO USE
L048
TECHNICAL DATA
N001
L047
MICRO-MWS
y OPERATIONAL GUIDANCE FOR MICRO-MWS DRILLS
Drill Length
Drill Installation
NG
D1
Thrust bearing type collet chuck

holds the drill securely.
A > D1 x 2
Do not clamp on the utes.
Through Coolant Type
Thin Workpiece
Coolant Handling
Spindle Through
Coolant Type
Coolant
Inducer Type
If Bending
Occurs
NG
Support
the Workpiece
Recommended coolant pressure:
> 435 PSI (3MPa)
At least 220 PSI (1.5MPa) is required.
1) Small particles of swarf will

jam in the oil hole of small
diameter drills. Always use
a ne mesh lter as a
preventative measure.
2) Dirt and dust particles
adhere to the oil in old
coolant and prevent an
efcient ow. Regular
coolant exchange is
recommended.
Good
y CAUTIONS FOR USE
DRILLING
a Please use a ne mesh lter (mesh < 3 micro) for coolant to prevent jamming in the oil hole.
a For deep drilling with the long type drill, machining a pilot hole is recommended.
L048
Drill Installation
Adjusting Screw
Drill Holding
(Otherwise, centrifugal forces may cause drill breakage.)
zA pilot hole must proceed

application of XB or DB drill.
xUse SB drill for pilot hole.
cDepending on cutting
conditions peck feeding may
be necessary.
y OPERATIONAL GUIDANCE FOR THE MICRO-MWS DRILL (L/D > 10)

zPenetrate the pilot hole at a low revolution. (Revolution speed

500-1000 min-1, feed rate .008-.012 IPR)
xStop the long type drill .020-.039 inch short of the pilot hole bottom.
zUse the SB type drill.

xUse a drill with the same diameter as the deep hole drill.
cDrill depth : Approx 1D.
vEnsure a high precision hole is drilled for the guide pilot.
zStart cutting at the recommended speed and feed with a non-peck

zAfter drilling, lower the cutting revolution about .020-.039 inch short of
the hole end. (Revolution speed of around 500-1000 min-1)
xRetract the drill to the pilot hole depth starting point at a feed rate of
120 inch/min.
cFinally clear the hole at a cutting speed of 65-100 SFM and feed rate of
.008-.012 IPR.
y 1. Spot facing
zMachine a flat on the irregular face by using an end mill or drill capable of
spot facing. Make the spot face diameter the same size as the required
deep hole diameter.
zPenetrate the pilot hole at a low revolution. (Revolution speed

500-1000 min-1, feed rate .008-.012 IPR)
xStop the long type drill .020-.039 inch short of the pilot hole bottom.
zWhen breaking through, the cutting edge can be damaged.

xFeed rate should be half the normal feed.
zUse a drill with a larger (flatter) point angle than XB or DB type. The
MWS-SB type is recommended.
xEnsure a high precision hole is drilled for the pilot.
cDrill depth : Approx 1D.
DRILLING
FLAT FACE DRILLING
zStart cutting at the recommended speed and feed with a non-peck

zFinally clear the hole at a revolution speed of 500-1000 min-1.

xRetract the drill to the pilot hole depth starting point at a feed rate of
120 inch/min.
L049
MICRO-MZE/MZS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
a Excellent
chip disposal.
through coolant hole enables high speed machining
(MZS type).
a Helical
.0394 < D1<.1094 D1=.1200
Heat Resistant
Alloy
D1 Tolerance
0
.00055
0
.00031
(inch)
D4 Tolerance
(inch)
INCH STANDARD
MZE (External coolant)
0
.00071
0
.00031
Type A
Type B
MZS
(Internal coolant)
Type A
Type B
DRILLING
.0394
2 Ext.
5 Int.
.0400
2 Ext.
5 Int.
.0410
2 Ext.
5 Int.
.0420
2 Ext.
5 Int.
.0430
2 Ext.
5 Int.
.0465
2 Ext.
5 Int.
.0520
2 Ext.
5 Int.
.0550
2 Ext.
5 Int.
.0591
2 Ext.
5 Int.
.0625
2 Ext.
5 Int.
.0635
2 Ext.
5 Int.
.0670
2 Ext.
5 Int.
.0700
2 Ext.
5 Int.
MZE00394SB
MZS00394LB
MZE00400SB
MZS00400LB
MZE00410SB
MZS00410LB
MZE00420SB
MZS00420LB
MZE00430SB
MZS00430LB
MZE00465SB
MZS00465LB
MZE00520SB
MZS00520LB
MZE00550SB
MZS00550LB
MZE00591SB
MZS00591LB
MZE00625SB
MZS00625LB
MZE00635SB
MZS00635LB
MZE00670SB
MZS00670LB
MZE00700SB
MZS00700LB
D4
D1
(inch) (l/d)
.236 .396 2.165 .1250 A

.433 .593 2.165 .1250 A
.0730
2 Ext.
5 Int.
.276 .435 2.165 .1250 A

.669 .828 2.165 .1250 A
.0760
2 Ext.
5 Int.
.276 .433 2.165 .1250 A

.669 .826 2.165 .1250 A
.0785
2 Ext.
5 Int.
.276 .431 2.165 .1250 A

.669 .826 2.165 .1250 A
.0810
2 Ext.
5 Int.
.276 .429 2.165 .1250 A

.669 .822 2.165 .1250 A
.0860
2 Ext.
5 Int.
.315 .461 2.165 .1250 A

.669 .815 2.165 .1250 A
.0890
2 Ext.
5 Int.
.354 .490 2.165 .1250 A

.669 .805 2.165 .1250 A
.0938
2 Ext.
5 Int.
.354 .485 2.165 .1250 A

.669 .800 2.165 .1250 A
.0960
2 Ext.
5 Int.
.354 .477 2.165 .1250 A

.669 .792 2.165 .1250 A
.1010
2 Ext.
5 Int.
.394 .511 2.165 .1250 A

.866 .983 2.677 .1250 A
.1040
2 Ext.
5 Int.
.394 .509 2.165 .1250 A

.866 .981 2.677 .1250 A
.1060
2 Ext.
5 Int.
.433 .541 2.165 .1250 A

.866 .974 2.677 .1250 A
.1094
2 Ext.
5 Int.
.433 .536 2.165 .1250 A

.866 .969 2.677 .1250 A
.1200
2 Ext.
5 Int.
Order Number
MZE00730SB
MZS00730LB
MZE00760SB
MZS00760LB
MZE00785SB
MZS00785LB
MZE00810SB
MZS00810LB
MZE00860SB
MZS00860LB
MZE00890SB
MZS00890LB
MZE00938SB
MZS00938LB
MZE00960SB
MZS00960LB
MZE01010SB
MZS01010LB
MZE01040SB
MZS01040LB
MZE01060SB
MZS01060LB
MZE01094SB
MZS01094LB
MZE01200SB
MZS01200LB
L050
L3
L2
L1
D4
Type
L1
Dimensions (inch)
Stock
VP15TF
L2
Hole Depth
L3
Drill
Dia.
Coolant
(Int./Ext.)
Order Number
Type
D1
(inch) (l/d)
Dimensions (inch)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
(Note) MICRO-MZE/MZS type can be used for shrink t holders.
.433 .530 2.165 .1250 A

.866 .963 2.677 .1250 A
.433 .524 2.165 .1250 A
.866 .957 2.677 .1250 A
.433 .520 2.165 .1250 A
.866 .953 2.677 .1250 A
.630 .712 2.165 .1250 A
1.102 1.184 2.913 .1250 A
.630 .703 2.165 .1250 A
1.102 1.175 2.913 .1250 A
.630 .697 2.165 .1250 A
1.102 1.169 2.913 .1250 A
.630 .688 2.165 .1250 A
1.102 1.160 2.913 .1250 A
.630 .684 2.165 .1250 A
1.102 1.156 2.913 .1250 A
.630 .630 2.165 .1250 B
1.299 1.299 3.189 .1250 B
.630 .630 2.165 .1250 B
1.299 1.299 3.189 .1250 B
.630 .630 2.165 .1250 B
1.299 1.299 3.189 .1250 B
.630 .630 2.165 .1250 B
1.299 1.299 3.189 .1250 B
.709 .709 2.165 .1250 B
1.535 1.535 3.425 .1250 B
D1 Tolerance
(mm)
D4 Tolerance
METRIC STANDARD
MZE (External coolant)
(mm)
MZE
MZS
D1<2
2 < D1< 3
0
0.014
0
0.006
0
0.006
0
0.014
0
0.014
0
0.006
Type A
Type B
4 < 2 : h6
*D
D4 > 2 : h8
MZS
(Internal coolant)
Type A
Type B
1.1
2 Ext.
5 Int.
1.2
2 Ext.
5 Int.
1.3
2 Ext.
5 Int.
1.4
2 Ext.
5 Int.
1.5
2 Ext.
5 Int.
1.6
2 Ext.
5 Int.
1.7
2 Ext.
5 Int.
1.8
2 Ext.
5 Int.
1.9
2 Ext.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
5 Int.
2 Ext.
3 Ext.
5 Int.
2.0
2.1
2.2
s
s
s
s
MZE0100SB
MZS0100LB
MZE0110SB
MZS0110LB
MZE0120SB
MZS0120LB
MZE0130SB
MZS0130LB
MZE0140SB
MZS0140LB
MZE0150SB
MZS0150LB
MZE0160SB
MZS0160LB
MZE0170SB
MZS0170LB
MZE0180SB
MZS0180LB
MZE0190SB
MZS0190LB
MZE0200SA
MZE0200MA
MZS0200MB
MZS0200LB
MZE0210SA
MZE0210MA
MZS0210LB
MZE0220SA
MZE0220MA
MZS0220LB
6
11
8
15
55
55
2.0
3.0
A
A
7
17
9
21
55
55
2.0
3.0
A
A
8
17
9
20
55
55
2.0
3.0
A
A
8
17
9
20
55
55
2.0
3.0
A
A
9
17
10
20
55
55
2.0
3.0
A
A
9
17
10
20
55
55
2.0
3.0
A
A
10
22
10
25
55
68
2.0
3.0
B
A
10
22
10
24
55
68
2.0
3.0
B
A
11
22
11
24
55
68
2.0
3.0
B
A
11
22
11
24
55
68
2.0
3.0
B
A
12
16
12
16
55
55
2.0
2.0
B
B
16
22
18
24
62
68
3.0
3.0
A
A
12
16
28
12
16
30
55
55
74
2.1
2.1
3.0
B
B
A
13
18
28
13
18
29
55
55
74
2.2
2.2
3.0
B
B
A
D1
(mm) (l/d)
2.3
2.4
2.5
2.6
2.7
2.8
2.9
VP15TF
D4
Hole Depth
L1
Coolant
(Int./Ext.)
L2
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
a
a
s
s
a
a
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
2 Ext.
3 Ext.
3 Int.
5 Int.
Dimensions (mm)
Stock
s
a
s
s
a
a
s
s
a
Order Number
MZE0230SA
MZE0230MA
MZS0230MB
MZS0230LB
MZE0240SA
MZE0240MA
MZS0240MB
MZS0240LB
MZE0250SA
MZE0250MA
MZS0250MB
MZS0250LB
MZE0260SA
MZE0260MA
MZS0260MB
MZS0260LB
MZE0270SA
MZE0270MA
MZS0270MB
MZS0270LB
MZE0280SA
MZE0280MA
MZS0280MB
MZS0280LB
MZE0290SA
MZE0290MA
MZS0290MB
MZS0290LB
L3
L2
L1
D4
13
18
13
18
55
55
2.3
2.3
B
B
20
28
21
29
66
74
3.0
3.0
A
A
16
20
16
20
55
55
2.4
2.4
B
B
20
28
21
29
66
74
3.0
3.0
A
A
16
20
16
20
55
55
2.5
2.5
B
B
20
28
21
29
66
74
3.0
3.0
A
A
16
20
16
20
55
55
2.6
2.6
B
B
24
33
24
33
72
81
3.0
3.0
B
B
16
20
16
20
55
55
2.7
2.7
B
B
24
33
24
33
72
81
3.0
3.0
B
B
16
21
16
21
55
60
2.8
2.8
B
B
24
33
24
33
72
81
3.0
3.0
B
B
16
21
16
21
55
60
2.9
2.9
B
B
24
33
24
33
72
81
3.0
3.0
B
B
CUTTING CONDITIONS
L052
HOW TO USE
L052
TECHNICAL DATA
N001
DRILLING
2 Ext.
5 Int.
L3
Drill
Dia.
Type
1.0
Order Number
Type
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
(Note 1) MICRO-MZE...SB type can be used for shrink t holders.

(Note 2) MICRO-MZS type can be used for shrink t holders.
L051
MICRO-MZE/MZS
y MZE (External coolant)
Work Material
&.0394" &.1200"
& 1.0 & 2.9mm
Cutting Speed
Feed
(SFM)
(IPR)
Mild Steel
< 180HB
75
.0035
Carbon Steel
Alloy Steel
180 280HB
65
.003
280 350HB
55
.0025
< 200HB
50
.0015
80
.003
M Stainless Steel
K
Drill Diameter
D1
Conditions
Hardness
Tensile Strength
< 350MPa
Strength
< 450MPa
Cast Iron
70
.003
32
.002
H Hardened Steel
40 60HRC
32
.002
y MZS (Internal coolant)

Work Material
&.0394" &.1200"
& 1.0 & 2.9mm
Cutting Speed
Feed
(SFM)
(IPR)
Mild Steel
< 180HB
200
.0035
Carbon Steel
Alloy Steel
180 280HB
175
.003
280 350HB
150
.0025
< 200HB
100
.0015
190
.003
130
.003
M Stainless Steel
K
Drill Diameter
D1
Conditions
Hardness
Tensile Strength
< 350MPa
Strength
< 450MPa
Cast Iron
N Aluminum Alloy
200
.003
65
.0015
DRILLING
y SPECIAL APPLICATION NOTES

For safety and success, always pre-drill the hole with a pilot drill.
This is especially true for drilling small sizes less than .1200" [2.9mm].
z A pilot hole must proceed application of LB drill.
x Use a SB drill with the same diameter for pilot hole.
c Depending on cutting conditions peck feeding may be necessary.
Minimum coolant pressure = 800psi (5.5 MPa).

Coolant must have Extreme Pressure (EP) Additives.
Positive displacement type coolant pump is required.
Coolant lter must be less than 5 microns. Fine ltration is necessary to
prevent blockage of the coolant Holes.
L052
Pilot
Drill
REASONABLE COOLANT FLOW AND PRESSURE FOR MZS DRILLS

Flow Rate and Pressure
Flow Rate
Flow Rate
Reasonable Range
Unreasonable Range
inch
Drill Diameter
inch
Drill Diameter
y PERFORMANCE REQUIREMENTS
1. High pressure pump system (800 psi or greater)
4. Coolant with Extreme Pressure additives
2. Filter to 5 microns
5. Use MZE pilot drill
3. Runout <.0003 max.
6. Recommended for rotating drill applications

DRILLING
In order for micro MZS Drills to perform properly you must

satisfy the following requirements.
L053
a Wide
MSE
ute for preventing chip jaming.

small diameter machining.
a Stable,
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
0.1 < D1< 3

D1 Tolerance
0
0.009
0
0.006
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
Type A
Type B
DRILLING
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.17
0.18
0.19
0.20
0.21
0.22
0.23
0.24
0.25
0.26
0.27
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
s
s
MSE0010SB
0011SB
0012SB
0013SB
0014SB
0015SB
0016SB
0017SB
0018SB
0019SB
0020SB
0021SB
0022SB
0023SB
0024SB
0025SB
0026SB
0027SB
0028SB
0029SB
0030SB
0031SB
0032SB
0033SB
0034SB
0035SB
0036SB
0037SB
0038SB
0039SB
0040SB
0041SB
L2
L1
D4
1.2
1.2
9.7
9.7
38
38
3
3
A
A
1.4
9.7
38
1.4
9.7
38
9.7
38
9.7
38
9.7
38
9.7
38
9.7
38
9.7
38
2.5
9.7
38
2.5
9.7
38
2.5
9.7
38
2.5
9.7
38
9.7
38
9.7
38
9.7
38
9.7
38
9.7
38
9.7
38
10.2
38
10.2
38
10.2
38
10.2
38
11.2
38
11.1
38
11.1
38
11.1
38
11.1
38
11.1
38
7
7
12.1
12.0
38
38
3
3
B
B
D1
(mm)
0.42
0.43
0.44
0.45
0.46
0.47
0.48
0.49
0.50
0.51
0.52
0.53
0.54
0.55
0.56
0.57
0.58
0.59
0.60
0.61
0.62
0.63
0.64
0.65
0.66
0.67
0.68
0.69
0.70
0.71
0.72
0.73
VP15TF
Type
L3
Dimensions (mm)
Stock
VP20MF
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
VP15TF
D1
(mm)
Dimensions (mm)
Stock
VP20MF
Drill
Dia.
Coolant
(Int./Ext.)
(Note) MSE type can be used for shrink t holders.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Order Number
MSE0042SB
0043SB
0044SB
0045SB
0046SB
0047SB
0048SB
0049SB
0050SB
0051SB
0052SB
0053SB
0054SB
0055SB
0056SB
0057SB
0058SB
0059SB
0060SB
0061SB
0062SB
0063SB
0064SB
0065SB
0066SB
0067SB
0068SB
0069SB
0070SB
0071SB
0072SB
0073SB
L054
Type
L3
L2
L1
D4
7
7
12.0
12.0
38
38
3
3
B
B
12.0
38
12.0
38
11.9
38
11.9
38
11.9
38
11.9
38
11.9
38
11.8
38
11.8
38
11.8
38
11.8
38
11.8
38
11.8
38
11.7
38
11.7
38
11.7
38
11.7
38
11.7
38
11.6
38
11.6
38
11.6
38
11.6
38
11.6
38
11.5
38
11.5
38
11.5
38
12.5
38
12.5
38
8
8
12.5
12.4
38
38
3
3
B
B
0.74
0.75
0.76
0.77
0.78
0.79
0.80
0.81
0.82
0.83
0.84
0.85
0.86
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
MSE0074SB
0075SB
0076SB
0077SB
0078SB
0079SB
0080SB
0081SB
0082SB
0083SB
0084SB
0085SB
0086SB
Type
L3
L2
L1
D4
8
8
12.4
12.4
38
38
3
3
B
B
12.4
38
12.4
38
12.3
38
12.3
38
10
14.3
38
10
14.3
38
10
14.3
38
10
14.3
38
10
14.2
38
10
10
14.2
14.2
38
38
3
3
B
B
D1
(mm)
0.87
0.88
0.89
0.90
0.91
0.92
0.93
0.94
0.95
0.96
0.97
0.98
0.99
Stock
VP15TF
Order Number
Drill
Dia.
VP20MF
Dimensions (mm)
Coolant
(Int./Ext.)
VP15TF
Stock
VP20MF
D1
(mm)
Coolant
(Int./Ext.)
Drill
Dia.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Dimensions (mm)
Order Number
MSE0087SB
0088SB
0089SB
0090SB
0091SB
0092SB
0093SB
0094SB
0095SB
0096SB
0097SB
0098SB
0099SB
Type
L3
L2
L1
D4
10
10
14.2
14.2
38
38
3
3
B
B
10
14.1
38
10
14.1
38
10
14.1
38
10
14.1
38
10
14.1
38
10
14.0
38
10
14.0
38
10
14.0
38
10
14.0
38
10
10
14.0
14.0
38
38
3
3
B
B

Work Material
& 0.10 & 0.19 mm

Drill Diameter D1
Conditions Revolution
Feed
Peck
(min-1)
(IPR)
(inch)
Hardness
& 0.20 & 0.29 mm
& 0.30 & 0.49 mm
Revolution
(min-1)
Feed
(IPR)
Peck
(inch)
Revolution
(min-1)
Feed
(IPR)
Peck
(inch)
General Steel
Carbon Steel
< 180HB
20000
.00008
.0008
20000
.00012
.0016
20000
.00016
.0020
Alloy Steel
Pre-hardened Steel
< 40HRC
20000
.00008
.0008
20000
.00012
.0016
20000
.00016
.0020
Stainless Steel
< 200HB
20000
.00008
.0008
18000
.00012
.0016
15000
.00016
.0020
Cast Iron
Tensile Strength
< 350MPa
20000
.00008
.0008
20000
.00012
.0016
20000
.00016
.0020
Aluminum Alloy
20000
.00016
.0020
20000
.00024
.0040
20000
.00080
.0118
7000
.00004
.0008
5000
.00008
.0016
4000
.00012
.0020
Work Material
& 0.50 & 0.79 mm

Drill Diameter D1
Conditions Revolution
Feed
Peck
(min-1)
(IPR)
(inch)
Hardness
& 0.80 & 0.99 mm

Revolution
(min-1)
Feed
(IPR)
Peck
(inch)
General Steel
Carbon Steel
< 180HB
20000
.00040
.0040
20000
.0016
.0118
Alloy Steel
Pre-hardened Steel
< 40HRC
20000
.00040
.0040
20000
.0008
.0118
Stainless Steel
< 200HB
10000
.00040
.0040
6000
.0008
.0080
Cast Iron
Tensile Strength
< 350MPa
20000
.00040
.0040
20000
.0016
.0018
Aluminum Alloy
20000
.00200
.0200
20000
.0024
.0315
3000
.00020
.0040
1800
.0004
.0080
DRILLING
(Note)
Use of the Starter Drill is recommended. (Order number: MSP0300SB, Cutting conditions: Please see page D056.)
Adjust the cutting conditions depending on the machine rigidity and component set up.
When drilling depth is over 5 times the drill diameter, reduce the peck distance above.
Use of water-soluble uid (Diluted x 20) is necessary for drilling using the cutting conditions above. Lower the cutting speed if oil or mist
coolant is used.
*
*
*
*
TECHNICAL DATA
N001
L055
MSP
STARTER Drill
a For
use with MSE Type drill.
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
METRIC STANDARD
(Note) MSP type can be used for shrink t holders.
Order Number
Grade
Stock
MSP0300SB
VP15TF
Dimensions (mm)
D1
D4
L1
L3
3.0
3.0
38
1.5

Order Number
Revolution
(min-1)
Table Feed
(IPR)
MSP0300SB
10000
.00002
DRILLING
L056
Range of Diameter
(mm)
0.1 0.99
y REFERENCE TABLE OF PRE-HOLE DIMENSIONS
MSE0010SB
0011SB
0012SB
0013SB
0014SB
0015SB
0016SB
0017SB
0018SB
0019SB
0020SB
0021SB
0022SB
0023SB
0024SB
0025SB
0026SB
0027SB
0028SB
0029SB
0030SB
0031SB
0032SB
0033SB
0034SB
0035SB
0036SB
0037SB
0038SB
0039SB
0040SB
0041SB
0042SB
0043SB
0044SB
0045SB
0046SB
0047SB
0048SB
0049SB
0050SB
0051SB
0052SB
0053SB
0054SB
Cutting
Dia.
Pre-hole
Diameter
Pre-hole
Depth
0.10
0.11
0.060 0.080
0.066 0.088
0.072 0.096
0.030 0.040
0.033 0.044
0.036 0.048
0.078 0.104
0.084 0.112
0.039 0.052
0.042 0.056
0.090 0.120
0.096 0.128
0.045 0.060
0.048 0.064
0.102 0.136
0.108 0.144
0.051 0.068
0.054 0.072
0.114 0.152
0.120 0.160
0.057 0.076
0.060 0.080
0.126 0.168
0.132 0.176
0.063 0.084
0.066 0.088
0.138 0.184
0.144 0.192
0.069 0.092
0.072 0.096
0.150 0.200
0.156 0.208
0.075 0.100
0.078 0.104
0.162 0.216
0.168 0.224
0.081 0.108
0.084 0.112
0.174 0.232
0.180 0.240
0.087 0.116
0.090 0.120
0.32
0.186 0.248
0.192 0.256
0.093 0.124
0.096 0.128
0.33
0.198 0.264
0.099 0.132
0.34
0.204 0.272
0.210 0.280
0.102 0.136
0.105 0.140
0.37
0.216 0.288
0.222 0.296
0.108 0.144
0.111 0.148
0.38
0.228 0.304
0.114 0.152
0.39
0.234 0.312
0.240 0.320
0.117 0.156
0.120 0.160
0.246 0.328
0.252 0.336
0.123 0.164
0.126 0.168
0.258 0.344
0.264 0.352
0.129 0.172
0.132 0.176
0.270 0.360
0.276 0.368
0.135 0.180
0.138 0.184
0.282 0.376
0.288 0.384
0.141 0.188
0.144 0.192
0.294 0.392
0.300 0.400
0.147 0.196
0.150 0.200
0.52
0.306 0.408
0.312 0.416
0.153 0.204
0.156 0.208
0.53
0.54
0.318 0.424
0.324 0.432
0.159 0.212
0.162 0.216
0.12
0.13
0.14
0.15
0.16
0.17
0.18
0.19
0.20
0.21
0.22
0.23
0.24
0.25
0.26
0.27
0.28
0.29
0.30
0.31
0.35
0.36
0.40
0.41
0.42
0.43
0.44
0.45
0.46
0.47
0.48
0.49
0.50
0.51
Description
MSE0055SB
0056SB
0057SB
0058SB
0059SB
0060SB
0061SB
0062SB
0063SB
0064SB
0065SB
0066SB
0067SB
0068SB
0069SB
0070SB
0071SB
0072SB
0073SB
0074SB
0075SB
0076SB
0077SB
0078SB
0079SB
0080SB
0081SB
0082SB
0083SB
0084SB
0085SB
0086SB
0087SB
0088SB
0089SB
0090SB
0091SB
0092SB
0093SB
0094SB
0095SB
0096SB
0097SB
0098SB
0099SB
Cutting
Dia.
Pre-hole
Diameter
Pre-hole
Depth
0.55
0.56
0.330 0.440
0.336 0.448
0.342 0.456
0.165 0.220
0.168 0.224
0.171 0.228
0.348 0.464
0.354 0.472
0.174 0.232
0.177 0.236
0.360 0.480
0.366 0.488
0.180 0.240
0.183 0.244
0.372 0.496
0.378 0.504
0.186 0.248
0.189 0.252
0.384 0.512
0.390 0.520
0.192 0.256
0.195 0.260
0.396 0.528
0.402 0.536
0.198 0.264
0.201 0.268
0.57
0.58
0.59
0.60
0.61
0.62
0.63
0.64
0.65
0.66
0.67
0.68
0.408 0.544
0.204 0.272
0.69
0.414 0.552
0.420 0.560
0.207 0.276
0.210 0.280
0.426 0.568
0.432 0.576
0.213 0.284
0.216 0.288
0.438 0.584
0.444 0.592
0.219 0.292
0.222 0.296
0.70
0.71
0.72
0.73
0.74
0.75
0.76
0.77
0.78
0.79
0.80
0.450 0.600
0.456 0.608
0.462 0.616
0.468 0.624
0.474 0.632
0.480 0.640
0.225 0.300
0.228 0.304
0.231 0.308
0.234 0.312
0.237 0.316
0.240 0.320
0.243 0.324
0.82
0.486 0.648
0.492 0.656
0.83
0.498 0.664
0.246 0.328
0.249 0.332
0.84
0.504 0.672
0.510 0.680
0.252 0.336
0.255 0.340
0.516 0.688
0.522 0.696
0.258 0.344
0.261 0.348
0.528 0.704
0.534 0.712
0.264 0.352
0.267 0.356
0.540 0.720
0.546 0.728
0.270 0.360
0.273 0.364
0.81
0.85
0.86
0.87
0.88
0.89
0.90
0.91
0.92
0.93
0.94
0.95
0.552 0.736
0.558 0.744
0.564 0.752
0.570 0.760
0.276 0.368
0.279 0.372
0.282 0.376
0.285 0.380
0.97
0.576 0.768
0.582 0.776
0.288 0.384
0.291 0.388
0.98
0.99
0.588 0.784
0.594 0.792
0.294 0.392
0.297 0.396
0.96
DRILLING
Description
Unit : mm
L057
a Small
diameter deep hole drilling.

hole accuracy is possible.
a Can be used with machining and turning center.
MICRO-MGS
a High
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
METRIC STANDARD
50
80
Int.
Int.
0.8
45
70
Int.
Int.
0.9
40
60
Int.
Int.
35
55
75
Int.
Int.
Int.
1.0
Int.
Int.
Int.
1.1
30
50
65
30
45
60
Int.
Int.
Int.
Int.
Int.
Int.
1.3
40
55
70
Int.
Int.
Int.
1.4
35
50
65
Int.
Int.
Int.
1.5
35
50
60
Int.
Int.
Int.
1.6
30
45
55
30
40
55
Int.
Int.
Int.
MGS0070L040B
0070L060B
0080L040B
0080L060B
0090L040B
0090L060B
0100L040B
0100L060B
0100L080B
0110L040B
0110L060B
0110L080B
0120L040B
0120L060B
0120L080B
0130L060B
0130L080B
0130L100B
0140L060B
0140L080B
0140L100B
0150L060B
0150L080B
0150L100B
0160L060B
0160L080B
0160L100B
0170L060B
0170L080B
0170L100B
1.2
1.7
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
D4
Order Number
D1
(mm) (l/d)
40
80
60 100
3
3
40
80
60 100
3
3
Int.
Int.
Int.
1.8
30
40
50
3
3
1.9
Int.
Int.
Int.
40
80
60 100
25
35
45
40
80
60 100
80 120
3
3
3
25
35
45
Int.
Int.
Int.
2.0
40
80
60 100
80 120
3
3
3
2.1
35
40
Int.
Int.
3
3
3
30
40
Int.
Int.
40
80
60 100
80 120
2.2
2.3
30
40
Int.
Int.
60 100
80 120
100 140
3
3
3
2.4
30
35
Int.
Int.
3
3
3
2.5
25
35
Int.
Int.
60 100
80 120
100 140
2.6
25
35
Int.
Int.
60 100
80 120
100 140
3
3
3
2.7
25
30
Int.
Int.
3
3
3
2.8
25
30
Int.
Int.
60 100
80 120
100 140
2.9
20
30
Int.
Int.
60 100
80 120
100 140
3
3
3
3.0
20
30
Int.
Int.
MGS0180L060B
0180L080B
0180L100B
0190L060B
0190L080B
0190L100B
0200L060B
0200L080B
0200L100B
0210L080B
0210L100B
0220L080B
0220L100B
0230L080B
0230L100B
0240L080B
0240L100B
0250L080B
0250L100B
0260L080B
0260L100B
0270L080B
0270L100B
0280L080B
0280L100B
0290L080B
0290L100B
0300L080B
0300L100B
L3
L1
s
s
s
s
s
s
(Note) Contact Mitsubishi Materials regarding coated products (VP, GP and UP coated carbide).
L058
Dimensions (mm)
Stock
HTi10
0.7
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
Order Number
D1
(mm) (l/d)
DRILLING
Dimensions (mm)
Stock
HTi10
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
(Note) MGS type can be used for shrink t holders.
L3
L1
D4
60 100
80 120
100 140
3
3
3
60 100
80 120
100 140
3
3
3
60 100
80 120
100 140
3
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
y DRIVER
y When connected with a driver.
Flute length
MGD38
MGD70
Dimensions (inch)
Stock
Order Number
s
s
D8
D4
.500
.500
L1
L3
.118 1.500 .496

.118 2.756 .984
L4
Clamp Wrench
Screw
.500 HSS04004 HKY20F

.787 HSS04004 HKY20F

Work Material
& 0.7 & 3.0 mm

Drill Diameter D1
Conditions Cutting speed
Feed
(SFM)
(IPR)
Hardness
Mild Steel
< 180HB
.0004
164
.0003
280 350HB
130
.0002
Stainless Steel
< 200HB
130
.0002
Gray Cast Iron
Tensile Strength
< 350MPa
230
.0008
Ductile Cast Iron
Tensile Strength
< 450MPa
130
.0006
360
.0008
230
.0008
Carbon Steel
Alloy Steel
230
180 280HB
N Aluminum Alloys
Copper Alloys
y Special Application Notes :

For safety and success, high pressure coolant is required.
(Minimum coolant pressure=1000PSI)
Coolant lter must be less than 5 microns.
Fine ltration is necessary to prevent blockage of the coolant
holes.
A pilot hole or guide bushing is required.
HOW TO USE
(Mitsubishis MZE, MZS, MWE or MWS is recommended.)
y 3. Coolant is turned ON, raise cutting speed and
feed to the recommended cutting condition.
y 2. Drill is inserted into the pilot hole.
(Drill is not rotating.)
DRILLING
y 1. Pilot hole drilling.
y 4. Return to Pos 2 after drilling end, coolant
turned OFF and drill rotation is stopped.
TECHNICAL DATA
N001
L059
a New grade DP7020 and a unique margin, developed specifically for stainless steel,
MMS
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
D1=3
0
0.014
0
0.008
D1 Tolerance
(mm)
D4 Tolerance
(mm)
D1(h8)
METRIC STANDARD
3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 20

0
0
0
0
0.033
0.027
0.022
0.018
0
0
0
0
0.013
0.011
0.009
0.008
D4(h6)
Hardened
Steel
140
Carbon Steel
Alloy Steel
complement high ow coolant holes.

a Long drill life and high efciency drilling of holes in stainless steel.
L3
L2
L1
3.0
3
5
Int.
Int.
3.1
3
5
Int.
Int.
3.2
3
5
Int.
Int.
3.3
3
5
Int.
Int.
3.4
3
5
Int.
Int.
3.5
3
5
Int.
Int.
3.6
3
5
Int.
Int.
3.7
3
5
Int.
Int.
3.8
3
5
Int.
Int.
3.9
3
5
Int.
Int.
4.0
3
5
Int.
Int.
4.1
3
5
Int.
Int.
4.2
3
5
Int.
Int.
4.3
3
5
Int.
Int.
4.4
3
5
Int.
Int.
4.5
3
5
Int.
Int.
4.6
3
5
Int.
Int.
4.7
3
5
Int.
Int.
4.8
3
5
Int.
Int.
L1
D4
D1
(mm) (l/d)
MMS0300X3DB
0300X5DB
0310X3DB
0310X5DB
0320X3DB
0320X5DB
0330X3DB
0330X5DB
0340X3DB
0340X5DB
0350X3DB
0350X5DB
0360X3DB
0360X5DB
0370X3DB
0370X5DB
0380X3DB
0380X5DB
0390X3DB
0390X5DB
0400X3DB
0400X5DB
0410X3DB
0410X5DB
0420X3DB
0420X5DB
0430X3DB
0430X5DB
0440X3DB
0440X5DB
0450X3DB
0450X5DB
0460X3DB
0460X5DB
0470X3DB
0470X5DB
0480X3DB
0480X5DB
DP7020
L2
Dimensions (mm)
Stock
Coolant
L3
Hole Depth
Order Number
Drill Dia.
DP7020
(mm) (l/d)
DRILLING
Dimensions (mm)
Stock
Coolant
D1
Hole Depth
Drill Dia.
When looking at the coating the color can vary depending on the direction
of viewing. This does not have any effect on the performance of the drill.
21
28
23
31
70
78
6
6
4.9
3
5
Int.
Int.
21
28
23
31
70
78
6
6
5.0
3
5
Int.
Int.
21
28
23
31
70
78
6
6
5.1
3
5
Int.
Int.
21
28
23
31
70
78
6
6
5.2
3
5
Int.
Int.
21
28
23
31
70
78
6
6
5.3
3
5
Int.
Int.
21
28
23
31
70
78
6
6
5.4
3
5
Int.
Int.
22
30
23
31
70
78
6
6
5.5
3
5
Int.
Int.
22
30
23
31
70
78
6
6
5.6
3
5
Int.
Int.
22
30
23
31
70
78
6
6
5.7
3
5
Int.
Int.
22
30
23
31
70
78
6
6
5.8
3
5
Int.
Int.
22
30
23
31
70
78
6
6
5.9
3
5
Int.
Int.
24
33
26
35
73
82
6
6
6.0
3
5
Int.
Int.
24
33
26
35
73
82
6
6
6.1
3
5
Int.
Int.
24
33
26
35
73
82
6
6
6.2
3
5
Int.
Int.
24
33
26
35
73
82
6
6
6.3
3
5
Int.
Int.
24
33
26
35
73
82
6
6
6.4
3
5
Int.
Int.
25
35
28
38
75
85
6
6
6.5
3
5
Int.
Int.
25
35
28
38
75
85
6
6
6.6
3
5
Int.
Int.
25
35
28
38
75
85
6
6
6.7
3
5
Int.
Int.
Order Number
MMS0490X3DB
0490X5DB
0500X3DB
0500X5DB
0510X3DB
0510X5DB
0520X3DB
0520X5DB
0530X3DB
0530X5DB
0540X3DB
0540X5DB
0550X3DB
0550X5DB
0560X3DB
0560X5DB
0570X3DB
0570X5DB
0580X3DB
0580X5DB
0590X3DB
0590X5DB
0600X3DB
0600X5DB
0610X3DB
0610X5DB
0620X3DB
0620X5DB
0630X3DB
0630X5DB
0640X3DB
0640X5DB
0650X3DB
0650X5DB
0660X3DB
0660X5DB
0670X3DB
0670X5DB
L3
L2
L1
D4
25
35
28
38
75
85
6
6
25
35
28
38
75
85
6
6
28
39
30
42
81
89
6
6
28
39
30
42
81
89
6
6
28
39
30
42
81
89
6
6
28
39
30
42
81
89
6
6
28
39
30
42
81
89
6
6
30
42
30
42
81
89
6
6
30
42
30
42
81
89
6
6
30
42
30
42
81
89
6
6
30
42
30
42
81
89
6
6
30
42
30
42
81
89
6
6
33
46
35
48
86
95
8
8
33
46
35
48
86
95
8
8
33
46
35
48
86
95
8
8
33
46
35
48
86
95
8
8
33
46
35
48
86
95
8
8
35
49
37
51
90
98
8
8
35
49
37
51
90
98
8
8
Note) Please contact Mitsubishi Carbide for any geometry that is not in the brochure (e.g. different diameter and length).
L060
3
5
Int.
Int.
6.9
3
5
Int.
Int.
7.0
3
5
Int.
Int.
7.1
3
5
Int.
Int.
7.2
3
5
Int.
Int.
7.3
3
5
Int.
Int.
7.4
3
5
Int.
Int.
7.5
3
5
Int.
Int.
7.6
3
5
Int.
Int.
7.7
3
5
Int.
Int.
7.8
3
5
Int.
Int.
7.9
3
5
Int.
Int.
8.0
3
5
Int.
Int.
8.1
3
5
Int.
Int.
8.2
3
5
Int.
Int.
8.3
3
5
Int.
Int.
8.4
3
5
Int.
Int.
8.5
3
5
Int.
Int.
8.6
3
5
Int.
Int.
8.7
3
5
Int.
Int.
8.8
3
5
Int.
Int.
8.9
3
5
Int.
Int.
9.0
3
5
Int.
Int.
9.1
3
5
Int.
Int.
D4
D1
Coolant
L1
Hole Depth
L2
Drill Dia.
L3
(mm) (l/d)
MMS0680X3DB
0680X5DB
0690X3DB
0690X5DB
0700X3DB
0700X5DB
0710X3DB
0710X5DB
0720X3DB
0720X5DB
0730X3DB
0730X5DB
0740X3DB
0740X5DB
0750X3DB
0750X5DB
0760X3DB
0760X5DB
0770X3DB
0770X5DB
0780X3DB
0780X5DB
0790X3DB
0790X5DB
0800X3DB
0800X5DB
0810X3DB
0810X5DB
0820X3DB
0820X5DB
0830X3DB
0830X5DB
0840X3DB
0840X5DB
0850X3DB
0850X5DB
0860X3DB
0860X5DB
0870X3DB
0870X5DB
0880X3DB
0880X5DB
0890X3DB
0890X5DB
0900X3DB
0900X5DB
0910X3DB
0910X5DB
35
49
37
51
90
98
8
8
3
5
Int.
Int.
35
49
37
51
90
98
8
8
9.3
3
5
Int.
Int.
35
49
37
51
90
98
8
8
9.4
3
5
Int.
Int.
38
53
39
56
90
103
8
8
9.5
3
5
Int.
Int.
38
53
39
56
90
103
8
8
9.6
3
5
Int.
Int.
38
53
39
56
90
103
8
8
9.7
3
5
Int.
Int.
38
53
39
56
90
103
8
8
9.8
3
5
Int.
Int.
38
53
39
56
90
103
8
8
9.9
3
5
Int.
Int.
40
56
40
56
90
103
8
8
10.0
3
5
Int.
Int.
40
56
40
56
90
103
8
8
10.1
3
5
Int.
Int.
40
56
40
56
90
103
8
8
10.2
3
5
Int.
Int.
40
56
40
56
90
103
8
8
10.3
3
5
Int.
Int.
40
56
40
56
90
103
8
8
10.4
3
5
Int.
Int.
43
60
45
62
96
113
10
10
10.5
3
5
Int.
Int.
43
60
45
62
96
113
10
10
10.6
3
5
Int.
Int.
43
60
45
62
96
113
10
10
10.7
3
5
Int.
Int.
43
60
45
62
96
113
10
10
10.8
3
5
Int.
Int.
43
60
45
62
96
113
10
10
10.9
3
5
Int.
Int.
45
63
47
65
101
116
10
10
11.0
3
5
Int.
Int.
45
63
47
65
101
116
10
10
11.1
3
5
Int.
Int.
45
63
47
65
101
116
10
10
11.2
3
5
Int.
Int.
45
63
47
65
101
116
10
10
11.3
3
5
Int.
Int.
45
63
47
65
101
116
10
10
11.4
3
5
Int.
Int.
48
67
50
70
101
121
10
10
11.5
3
5
Int.
Int.
9.2
Order Number
MMS0920X3DB
0920X5DB
0930X3DB
0930X5DB
0940X3DB
0940X5DB
0950X3DB
0950X5DB
0960X3DB
0960X5DB
0970X3DB
0970X5DB
0980X3DB
0980X5DB
0990X3DB
0990X5DB
1000X3DB
1000X5DB
1010X3DB
1010X5DB
1020X3DB
1020X5DB
1030X3DB
1030X5DB
1040X3DB
1040X5DB
1050X3DB
1050X5DB
1060X3DB
1060X5DB
1070X3DB
1070X5DB
1080X3DB
1080X5DB
1090X3DB
1090X5DB
1100X3DB
1100X5DB
1110X3DB
1110X5DB
1120X3DB
1120X5DB
1130X3DB
1130X5DB
1140X3DB
1140X5DB
1150X3DB
1150X5DB
L3
L2
L1
D4
48
67
50
70
101
121
10
10
48
67
50
70
101
121
10
10
48
67
50
70
101
121
10
10
48
67
50
70
101
121
10
10
50
70
50
70
101
121
10
10
50
70
50
70
101
121
10
10
50
70
50
70
101
121
10
10
50
70
50
70
101
121
10
10
50
70
50
70
101
121
10
10
53
74
55
78
111
134
12
12
53
74
55
78
111
134
12
12
53
74
55
78
111
134
12
12
53
74
55
78
111
134
12
12
53
74
55
78
111
134
12
12
55
77
56
78
116
134
12
12
55
77
56
78
116
134
12
12
55
77
56
78
116
134
12
12
55
77
56
78
116
134
12
12
55
77
56
78
116
134
12
12
58
81
60
84
116
140
12
12
58
81
60
84
116
140
12
12
58
81
60
84
116
140
12
12
58
81
60
84
116
140
12
12
58
81
60
84
116
140
12
12
CUTTING CONDITIONS
L064
TECHNICAL DATA
N001
DRILLING
6.8
Order Number
Dimensions (mm)
Stock
DP7020
(mm) (l/d)
DP7020
Coolant
Hole Depth
Drill Dia.
D1
Dimensions (mm)
Stock
L061
a New grade DP7020 and a unique margin, developed specifically for stainless steel,
MMS
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
D1=3
0
0.014
0
0.008
D4 Tolerance
(mm)
D1 Tolerance
(mm)
D1(h8)
METRIC STANDARD
3<D1< 6 6<D1< 10 10<D1< 18 18<D1< 20

0
0
0
0
0.033
0.027
0.022
0.018
0
0
0
0
0.013
0.011
0.009
0.008
D4(h6)
Hardened
Steel
140
Carbon Steel
Alloy Steel
complement high ow coolant holes.

a Long drill life and high efciency drilling of holes in stainless steel.
L3
L2
L1
11.6
3
5
Int.
Int.
11.7
3
5
Int.
Int.
11.8
3
5
Int.
Int.
11.9
3
5
Int.
Int.
12.0
3
5
Int.
Int.
12.1
3
5
Int.
Int.
12.2
3
5
Int.
Int.
12.3
3
5
Int.
Int.
12.4
3
5
Int.
Int.
12.5
3
5
Int.
Int.
12.6
3
5
Int.
Int.
12.7
3
5
Int.
Int.
12.8
3
5
Int.
Int.
12.9
3
5
Int.
Int.
13.0
3
5
Int.
Int.
13.1
3
5
Int.
Int.
13.2
3
5
Int.
Int.
13.3
3
5
Int.
Int.
13.4
3
5
Int.
Int.
L1
D4
D1
(mm) (l/d)
MMS1160X3DB
1160X5DB
1170X3DB
1170X5DB
1180X3DB
1180X5DB
1190X3DB
1190X5DB
1200X3DB
1200X5DB
1210X3DB
1210X5DB
1220X3DB
1220X5DB
1230X3DB
1230X5DB
1240X3DB
1240X5DB
1250X3DB
1250X5DB
1260X3DB
1260X5DB
1270X3DB
1270X5DB
1280X3DB
1280X5DB
1290X3DB
1290X5DB
1300X3DB
1300X5DB
1310X3DB
1310X5DB
1320X3DB
1320X5DB
1330X3DB
1330X5DB
1340X3DB
1340X5DB
DP7020
L2
Dimensions (mm)
Stock
Coolant
L3
Hole Depth
Order Number
Drill Dia.
DP7020
(mm) (l/d)
DRILLING
Dimensions (mm)
Stock
Coolant
D1
Hole Depth
Drill Dia.
looking at the coating the color can vary depending on the direction
*When
of viewing. This does not have any effect on the performance of the drill.
60
84
60
84
116
140
12
12
13.5
3
5
Int.
Int.
60
84
60
84
116
140
12
12
13.6
3
5
Int.
Int.
60
84
60
84
116
140
12
12
13.7
3
5
Int.
Int.
60
84
60
84
116
140
12
12
13.8
3
5
Int.
Int.
60
84
60
84
116
140
12
12
13.9
3
5
Int.
Int.
63
88
66
92
122
148
14
14
14.0
3
5
Int.
Int.
63
88
66
92
122
148
14
14
14.1
3
5
Int.
Int.
63
88
66
92
122
148
14
14
14.2
3
5
Int.
Int.
63
88
66
92
122
148
14
14
14.3
3
5
Int.
Int.
63
88
66
92
122
148
14
14
14.4
3
5
Int.
Int.
65
91
66
92
122
148
14
14
14.5
3
5
Int.
Int.
65
91
66
92
122
148
14
14
14.6
3
5
Int.
Int.
65
91
66
92
122
148
14
14
14.7
3
5
Int.
Int.
65
91
66
92
122
148
14
14
14.8
3
5
Int.
Int.
65
91
66
92
122
148
14
14
14.9
3
5
Int.
Int.
68
95
70
98
126
154
14
14
15.0
3
5
Int.
Int.
68
95
70
98
126
154
14
14
15.1
3
5
Int.
Int.
68
95
70
98
126
154
14
14
15.2
3
5
Int.
Int.
68
95
70
98
126
154
14
14
15.3
3
5
Int.
Int.
Order Number
MMS1350X3DB
1350X5DB
1360X3DB
1360X5DB
1370X3DB
1370X5DB
1380X3DB
1380X5DB
1390X3DB
1390X5DB
1400X3DB
1400X5DB
1410X3DB
1410X5DB
1420X3DB
1420X5DB
1430X3DB
1430X5DB
1440X3DB
1440X5DB
1450X3DB
1450X5DB
1460X3DB
1460X5DB
1470X3DB
1470X5DB
1480X3DB
1480X5DB
1490X3DB
1490X5DB
1500X3DB
1500X5DB
1510X3DB
1510X5DB
1520X3DB
1520X5DB
1530X3DB
1530X5DB
L3
L2
L1
D4
68
95
70
98
126
154
14
14
70
98
70
98
126
154
14
14
70
98
70 126
98 154
70
98
70 126
98 154
70
98
70 126
98 154
70
98
70 126
98 154
14
14
14
14
14
14
14
14
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
73 76 135
102 106 165
73 76 135
102 106 165
73 76 135
102 106 165
73 76 135
102 106 165
73 76 135
102 106 165
75 76 135
105 106 165
75 76 135
105 106 165
75 76 135
105 106 165
75 76 135
105 106 165
75 76 135
105 106 165
78 80 139
109 112 171
78 80 139
109 112 171
78 80 139
109 112 171
Note) Please contact Mitsubishi Carbide for any geometry that is not in the brochure (e.g. different diameter and length).
L062
3
5
Int.
Int.
15.5
3
5
Int.
Int.
15.6
3
5
Int.
Int.
15.7
3
5
Int.
Int.
15.8
3
5
Int.
Int.
15.9
3
5
Int.
Int.
16.0
3
5
Int.
Int.
16.1
3
5
Int.
Int.
16.2
3
5
Int.
Int.
16.3
3
5
Int.
Int.
16.4
3
5
Int.
Int.
16.5
3
5
Int.
Int.
16.6
3
5
Int.
Int.
16.7
3
5
Int.
Int.
16.8
3
5
Int.
Int.
16.9
3
5
Int.
Int.
17.0
3
5
Int.
Int.
17.1
3
5
Int.
Int.
17.2
3
5
Int.
Int.
17.3
3
5
Int.
Int.
17.4
3
5
Int.
Int.
17.5
3
5
Int.
Int.
17.6
3
5
Int.
Int.
17.7
3
5
Int.
Int.
D4
D1
Coolant
L1
Hole Depth
L2
Drill Dia.
L3
(mm) (l/d)
MMS1540X3DB
1540X5DB
1550X3DB
1550X5DB
1560X3DB
1560X5DB
1570X3DB
1570X5DB
1580X3DB
1580X5DB
1590X3DB
1590X5DB
1600X3DB
1600X5DB
1610X3DB
1610X5DB
1620X3DB
1620X5DB
1630X3DB
1630X5DB
1640X3DB
1640X5DB
1650X3DB
1650X5DB
1660X3DB
1660X5DB
1670X3DB
1670X5DB
1680X3DB
1680X5DB
1690X3DB
1690X5DB
1700X3DB
1700X5DB
1710X3DB
1710X5DB
1720X3DB
1720X5DB
1730X3DB
1730X5DB
1740X3DB
1740X5DB
1750X3DB
1750X5DB
1760X3DB
1760X5DB
1770X3DB
1770X5DB
78 80 139
109 112 171
78 80 139
109 112 171
16
16
16
16
80 80 139
112 112 171
16
16
18.0
3
5
Int.
Int.
80 80 139
112 112 171
16
16
18.1
3
5
Int.
Int.
80 80 139
112 112 171
16
16
18.2
3
5
Int.
Int.
80 80 139
112 112 171
16
16
18.3
3
5
Int.
Int.
80 80 139
112 112 171
16
16
18.4
3
5
Int.
Int.
83 86 145
116 120 179
18
18
18.5
3
5
Int.
Int.
83 86 145
116 120 179
18
18
18.6
3
5
Int.
Int.
83 86 145
116 120 179
18
18
18.7
3
5
Int.
Int.
83 86 145
116 120 179
18
18
18.8
3
5
Int.
Int.
83 86 145
116 120 179
18
18
18.9
3
5
Int.
Int.
85 86 145
119 120 179
18
18
19.0
3
5
Int.
Int.
85 86 145
119 120 179
18
18
19.1
3
5
Int.
Int.
85 86 145
119 120 179
18
18
19.2
3
5
Int.
Int.
85 86 145
119 120 179
18
18
19.3
3
5
Int.
Int.
85 86 145
119 120 179
18
18
19.4
3
5
Int.
Int.
88 90 149
123 126 185
18
18
19.5
3
5
Int.
Int.
88 90 149
123 126 185
18
18
19.6
3
5
Int.
Int.
88 90 149
123 126 185
18
18
19.7
3
5
Int.
Int.
88 90 149
123 126 185
18
18
19.8
3
5
Int.
Int.
88 90 149
123 126 185
18
18
19.9
3
5
Int.
Int.
90 90 149
126 126 185
18
18
20.0
3
5
Int.
Int.
90 90 149
126 126 185
18
18
17.8
3
5
Int.
Int.
17.9
3
5
Int.
Int.
Order Number
MMS1780X3DB
1780X5DB
1790X3DB
1790X5DB
1800X3DB
1800X5DB
1810X3DB
1810X5DB
1820X3DB
1820X5DB
1830X3DB
1830X5DB
1840X3DB
1840X5DB
1850X3DB
1850X5DB
1860X3DB
1860X5DB
1870X3DB
1870X5DB
1880X3DB
1880X5DB
1890X3DB
1890X5DB
1900X3DB
1900X5DB
1910X3DB
1910X5DB
1920X3DB
1920X5DB
1930X3DB
1930X5DB
1940X3DB
1940X5DB
1950X3DB
1950X5DB
1960X3DB
1960X5DB
1970X3DB
1970X5DB
1980X3DB
1980X5DB
1990X3DB
1990X5DB
2000X3DB
2000X5DB
L3
L2
L1
D4
90 90 149
126 126 185
18
18
90 90 149
126 126 185
18
18
90 90 149
126 126 185
18
18
93 96 157
130 134 191
20
20
93 96 157
130 134 191
20
20
93 96 157
130 134 191
20
20
93 96 157
130 134 191
20
20
93 96 157
130 134 191
20
20
95 96 157
133 134 195
20
20
95 96 157
133 134 195
20
20
95 96 157
133 134 195
20
20
95 96 157
133 134 195
20
20
95 96 157
133 134 195
20
20
98 100 161
137 140 201
20
20
98 100 161
137 140 201
20
20
98 100 161
137 140 201
20
20
98 100 161
137 140 201
20
20
98 100 161
137 140 201
20
20
100 100 161

140 140 201
20
20
100 100 161

140 140 201
20
20
100 100 161

140 140 201
20
20
100 100 161

140 140 201
20
20
100 100 161

140 140 201
20
20
CUTTING CONDITIONS
L064
TECHNICAL DATA
N001
DRILLING
15.4
Order Number
Dimensions (mm)
Stock
DP7020
(mm) (l/d)
DP7020
Coolant
Hole Depth
Drill Dia.
D1
Dimensions (mm)
Stock
L063
MMS
Work Material
No
Hardness
& 3.0 & 3.9mm
Feed (IPR)
Drill Diameter
D1
& 4.0 & 5.9mm
& 6.0 & 7.9mm
& 8.0 & 9.9mm
Cutting speed
(SFM)
Ferritic, Martensitic
Stainless Steel
< 200HB
195 260 330
.003 .005 .007
.004 .006 .008
.005 .007 .009
.005 .007 .009
> 200HB
130 195 260
.003 .004 .007
.004 .005 .008
.005 .006 .009
.005 .006 .009
PH Stainless Steel
< 450HB
130 165 260
.003 .004 .007
.004 .005 .008
.005 .006 .009
.005 .006 .009
Austenitic
Stainless Steel
< 200HB
195 260 330
.003 .005 .007
.004 .006 .008
.005 .007 .009
.005 .007 .009
> 200HB
130 195 260
.003 .004 .007
.004 .005 .008
.005 .006 .009
.005 .006 .009
Duplex Steel
135HB 275HB
130 165 260
.003 .004 .007
.004 .005 .008
.005 .006 .009
.005 .006 .009
Work Material
No
Hardness
Stainless Steel
< 200HB
165 195 230
.006 .008 .009
.006 .008 .010
.006 .009 .010
.007 .009 .011
> 200HB
130 165 195
.006 .007 .009
.006 .007 .010
.006 .008 .010
.007 .008 .011
PH Stainless Steel
< 450HB
100 130 165
.006 .007 .009
.006 .007 .010
.006 .008 .010
.007 .008 .011
Austenitic
Stainless Steel
< 200HB
165 195 230
.006 .008 .009
.006 .008 .010
.006 .009 .010
.007 .009 .011
> 200HB
130 165 195
.006 .007 .009
.006 .007 .010
.006 .008 .010
.007 .008 .011
Duplex Steel
135HB 275HB
100 130 165
.006 .007 .009
.006 .007 .010
.006 .008 .010
.007 .008 .011
Cutting speed
(SFM)
Feed (IPR)
Drill Diameter
D1
& 10.0 & 11.9mm & 12.0 & 15.9mm & 16.0 & 19.9mm
(Note 1) Spindle through & high pressure coolant system is recommended to make stable holes.
(Note 2) Emulsion type of water coolant is recommended.
(Note 3) In non water cutting uid, reduce the cutting speed by 10%-20%.
y Stainless Steel Cross Reference List

Work Material
No
DRILLING
Stainless Steel
PH Stainless Steel
Austenitic
Stainless Steel
Duplex Steel
L064
USA
AIS/SAE
Japan
JIS
416
410
430
434
430Ti
409
420
431
420
440C
630 (17-4PH)
S15500 (15-5PH)
631 (17-7PH)
SUS416
SUS410
SUS430
SUS434
SUS430LX

SUS420J1
SUS431
SUS420J2
SUS440C
SUS630

SUS631
SUS304
SUS305
SUS303
SUS304L
SUS316
SUS304LN
SUS316L
SUS316LN
SUS316L
SUS317L

SUS321
SUS347
SUS316Ti

SCS14A
SUS329J1
SUS329J3L
304
305
303
304L
316
304LN
316L
316LN

317L
N08926
321
347
316Ti

S32750
329
S31803
Germany
W-no.
DIN
1.4005
1.4006
X12CrS3
X10Cr13
X6Cr17
X6CrMo17
X6CrTi17
X6CrTi12
X20Cr13
X20CrNi17-2
X30Cr13
X10CrMo17
X5CrNiCuNb16 4

X7CrNiAl17 7
X5CrNi18 10
X5CrNi8-12
X12CrNiS18-9
X2CrNi19-11
X5CrNiMo17 12 2
X2CrNiN18 10
X2CrNiMo17 12 2
X2CrNiMoN17 12 2
X2CrNiMo18 14 3
X2CrNiMo18 15 4
X1NiCrMoCuN25 20 7
X6CrNiTi18-10
X6CrNiNb18-10
X6CrNiMoTi17 12 2
X2CrNiN23 4
X2CrNiMoN25 7 4
X3CrNiMoN27 5 2
X2CrNiMoN22 5 3
1.4016
1.4113
1.4510
1.4512
1.4021
1.4057
1.4028
1.4125
1.4542
1.4545
1.4568
1.4301
1.4303
1.4305
1.4307
1.4401
1.4311
1.4404
1.4406
1.4435
1.4438
1.4529
1.4541
1.4550
1.4571
1.4362
1.4410
1.4460
1.4462
& 20.0mm
y Operational Guidance for the MMS Drill

Drill holding
Drill Installation
Installation tolerance
Adjusting screw
Drill holding
D1

A : > D1 x 1.5
Runout < .001"
Coolant handling
Thin workpieces
Interrupted cutting
Spindle through
coolant type
Coolant
inducer type
< MMS type >

1) Dirt and dust particles in old
coolant can clog the oil hole
and prevent effective flow.
Regular coolant exchange is
recommended.
jam in the oil hole. Use a lter
as a preventative measure.
When using small diameter
drills, use a ne mesh lter.
If bending
occurs
zLower the feed

when drilling the
interrupted part.
Requires prior
machining
Support the
workpiece
zSpot face with an
end mill prior to
drilling.
Coolant pressure is approx.

70 - 1015 PSI (0.5 - 7MPa).
Burring and workpiece chipping
DRILLING
Stepped holes
One process
zDivide the machining into two

processes.
xDrill the larger hole rst.
Tools for chamfering and spot
facing can be produced to
order.
zLower the feed rate when

breaking through.
xAdd a chamfer.
cChange the point angle.
L065
a Specialized
in aluminum and cast iron drilling.

hole accuracy.
a Pre-hole drilling for rolled tap.
a Helical coolant hole enables high speed machining.
MAS
Carbon Steel
Alloy Steel
Hardened
Steel
a High
Stainless
Steel
Cast Iron
Light Alloy
.1250<D1< .2344 .2500<D1< .3906 .4062<D1< .7031 .7188<D1< .7812
Heat Resistant
Alloy
D1 Tolerance
(inch)
D4 Tolerance
(inch)
INCH STANDARD
L/D=3
+ .00020
0
0
.00031
+ .00020
0
0
.00035
+ .00020
0
0
.00043
+ .00020
0
0
.00051
Internal Coolant
(Note 1) MAS type larger than & .2031" have a recess in the shank end face.
(Note 2) MAS type can be used for shrink t holders.
Order Number
D1
(inch)
.1250
.1406
.1495
.1563
.1590
.1719
.1875
.2031
.2165
.2188
.2344
.2500
.2570
.2656
.2720
.2812
.2969
DRILLING
.3125
.3281
.3320
.3438
.3594
.3680
.3750
.3906
.4062
MAS01250MB
01406MB
01495MB
01563MB
01590MB
01719MB
01875MB
02031MB
02165MB
02188MB
02344MB
02500MB
02570MB
02656MB
02720MB
02812MB
02969MB
03125MB
03281MB
03320MB
03438MB
03594MB
03680MB
03750MB
03906MB
04062MB
Dimensions (inch)
L3
L1
D4
Rolled
Thread
Tap Size
Drill
Dia.
.945 2.520
1.102 2.677
.157
.157
.4219
.4375
1.102 2.677
.157 10-24NC
.4531
1.102 2.677
.157
.4688
1.220 2.795
.197 10-32NF
.4844
1.220 2.795
.197
.5000
1.299 2.874
.197
.5118
1.417 2.992
.236
.5156
1.417 2.992
.236
.5312
1.535 3.110
.236
.5469
1.535 3.110
.236
.5625
1.654 3.307
.276 1/16-27NS
.5781
1.654 3.307
.276 5/16-18NC
.5937
1.654 3.307
.276
.6094
1.654 3.307
.276 5/16-24NF
.6250
1.890 3.543
.315
.6406
1.890 3.543
.315
.6563
1.890 3.543
.315 3/8-16NC
.6718
1.969 3.701
.354 1/8-27NPT
.6875
1.969 3.701
.354 3/8-24NF
.7031
1.969 3.701
.354
.7188
2.087 3.819
.394
.7344
2.087 3.819
.394 7/16-14NC
.7500
2.087 3.819
.394
2.087 3.819
2.165 3.976
.394 7/16-20NF
.433
.7656
.7812
Order Number
MAS04219MB
04375MB
04531MB
04688MB
04844MB
05000MB
05118MB
05156MB
05312MB
05469MB
05625MB
05781MB
05937MB
06094MB
06250MB
06406MB
06563MB
06718MB
06875MB
07031MB
07188MB
07344MB
07500MB
07656MB
07812MB
D1
(inch)
Stock
HTi10
Stock
HTi10
Drill
Dia.
Helix Angle : 10
Dimensions (inch)
L3
D4
Rolled
Thread
Tap Size
2.165 3.976
2.362 4.173
.433 1/2-13, 1/2-12

.472 1/4-18NPT
2.362 4.173
.472 1/2-20, 1/4-18NS
2.362 4.173
.472
2.559 4.528
.512 9/16-12NC
2.559 4.528
.512
2.559 4.528
.512
2.756 4.724
.551 9/16-18NF
2.756 4.724
.551 5/8-11NC
2.756 4.724
.551
2.835 5.118
.591 3/8-18NPT
2.835 5.118
.591 5/8-18NF
2.992 5.276
.630 3/8-18NS
2.992 5.276
.630
2.992 5.276
.630
3.150 5.433
.669
3.150 5.433
.669 3/4-10NC
3.346 5.630
.709
3.346 5.630
.709 3/4-16NF
3.346 5.630
.709 1/2-14NPT
3.543 5.827
.748
3.543 5.827
.748 7/8-9, 1/2-14NS
3.740 6.024
.787
3.740 6.024
3.740 6.024
.787
.787
L066
L1

Work Material
Drill Dia. &.1250" &.2344"
Drill Dia. &.2500" &.3906"
Drill Dia. &.4062" &.7812"
Cutting Speed
(SFM)
Feed
(IPR)
Cutting Speed
(SFM)
Feed
(IPR)
Cutting Speed
(SFM)
Feed
(IPR)
N Aluminum Alloy Casting
330 (195 490)
.006 (.002 .012)
390 (260 555)
.008 (.004 .012)
490 (330 655)
.010 (.004 .016)
Aluminum Alloy Die Casting
390 (260 555)
.005 (.002 .010)
490 (330 590)
.006 (.002 .010)
525 (390 655)
.008 (.004 .012)
Gray Cast Iron
195 (130 260)
.006 (.004 .008)
260 (195 360)
.008 (.004 .012)
330 (230 425)
.012 (.008 .016)
Ductile Cast Iron
145 (100 195)
.004 (.002 .006)
195 (130 260)
.005 (.002 .008)
260 (195 330)
.008 (.004 .012)
y MACHINED HOLE ACCURACY

Feed : .008inch/rev
Oversize
Drilled Depth : 2.36inch (Through hole)
Roundness
Roundness (m)
Surface nish (m)
Oversize (m)
Cutting speed (SFM)
WSO (10%)
Surface Roughness
Cutting speed (SFM)
Cutting speed (SFM)
DRILLING
Tool : MAS1000LB Workpiece : 330Aluminum
TECHNICAL DATA
N001
L067
a Specialized

hole accuracy.
MAE/MAS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
a High
Light Alloy
Heat Resistant
Alloy
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
MAE (External Coolant)
D1=3
3<D1< 6
+0.005
0
0
0.006
+0.005
0
0
0.008
6<D1< 10 10<D1< 16
+0.005
0
0
0.009
+0.005
0
0
0.011
MAS (Internal Coolant)
3 Ext.
3 Int.
6 Int.
3.0
3.1
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
3.3
3 Ext.
3 Int.
6 Int.
3.4
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
3.5
3.6
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
3.65
3.7
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
DRILLING
3.2
3.8
*
*
*
MAE0300MB
MAS0300MB
MAS0300LB
MAE0310MB
MAS0310MB
MAS0310LB
MAE0320MB
MAS0320MB
MAS0320LB
MAE0330MB
MAS0330MB
MAS0330LB
MAE0340MB
MAS0340MB
MAS0340LB
MAE0350MB
MAS0350MB
MAS0350LB
MAE0360MB
MAS0360MB
MAS0360LB
MAE0365MB
MAS0365MB
MAS0365LB
MAE0370MB
MAS0370MB
MAS0370LB
MAE0380MB
MAS0380MB
MAS0380LB
L1
D4
21
21
30
61
61
70
3.0
3.0
3.0
24
24
34
64
64
74
4.0
4.0
4.0
24
24
34
64
64
74
4.0
4.0
4.0
24
24
34
64
64
74
4.0
4.0
4.0
24
24
34
64
64
74
24
24
34
D1
(mm) (l/d)
3 Ext.
3 Int.
6 Int.
3.9
4.0
3 Ext.
3 Int.
6 Int.
4.1
3 Ext.
3 Int.
6 Int.
4.2
3 Ext.
3 Int.
6 Int.
4.0
4.0
4.0
4.3
3 Ext.
3 Int.
6 Int.
64
64
74
4.0
4.0
4.0
3 Ext.
3 Int.
6 Int.
4.4
28
28
40
68
68
80
4.0
4.0
4.0
4.5
3 Ext.
3 Int.
6 Int.
28
28
40
68
68
80
4.0
4.0
4.0
3 Ext.
3 Int.
6 Int.
4.6
28
28
40
68
68
80
4.0
4.0
4.0
4.7
3 Ext.
3 Int.
6 Int.
28
28
40
68
68
80
4.0
4.0
4.0
4.8
3 Ext.
3 Int.
6 Int.
* : Standard hole size for rolled thread tap.
Dimensions (mm)
Stock
Order Number
HTi10
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
HTi10
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
(Note 1) MAS type larger than & 5.0 have a recess in the shank end face.
(Note 2) MAE/MAS type can be used for shrink t holders.
*
*
*
MAE0390MB
MAS0390MB
MAS0390LB
MAE0400MB
MAS0400MB
MAS0400LB
MAE0410MB
MAS0410MB
MAS0410LB
MAE0420MB
MAS0420MB
MAS0420LB
MAE0430MB
MAS0430MB
MAS0430LB
MAE0440MB
MAS0440MB
MAS0440LB
MAE0450MB
MAS0450MB
MAS0450LB
MAE0460MB
MAS0460MB
MAS0460LB
MAE0470MB
MAS0470MB
MAS0470LB
MAE0480MB
MAS0480MB
MAS0480LB
L068
L3
L1
D4
28
28
40
68
68
80
4.0
4.0
4.0
28
28
40
68
68
80
4.0
4.0
4.0
31
31
44
71
71
84
5.0
5.0
5.0
31
31
44
71
71
84
5.0
5.0
5.0
31
31
44
71
71
84
5.0
5.0
5.0
31
31
44
71
71
84
5.0
5.0
5.0
31
31
44
71
71
84
5.0
5.0
5.0
33
33
48
73
73
88
5.0
5.0
5.0
33
33
48
73
73
88
5.0
5.0
5.0
33
33
48
73
73
88
5.0
5.0
5.0
5.0
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
5.2
3 Ext.
3 Int.
6 Int.
5.3
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
5.4
5.5
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
5.6
5.7
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
5.9
3 Ext.
3 Int.
6 Int.
6.0
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
6.1
6.2
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
5.8
6.3
s
s
s
s
s
s
*
*
*
MAE0490MB
MAS0490MB
MAS0490LB
MAE0500MB
MAS0500MB
MAS0500LB
MAE0510MB
MAS0510MB
MAS0510LB
MAE0520MB
MAS0520MB
MAS0520LB
MAE0530MB
MAS0530MB
MAS0530LB
MAE0540MB
MAS0540MB
MAS0540LB
MAE0550MB
MAS0550MB
MAS0550LB
MAE0560MB
MAS0560MB
MAS0560LB
MAE0570MB
MAS0570MB
MAS0570LB
MAE0580MB
MAS0580MB
MAS0580LB
MAE0590MB
MAS0590MB
MAS0590LB
MAE0600MB
MAS0600MB
MAS0600LB
MAE0610MB
MAS0610MB
MAS0610LB
MAE0620MB
MAS0620MB
MAS0620LB
MAE0630MB
MAS0630MB
MAS0630LB
D4
33
33
48
73
73
88
5.0
5.0
5.0
33
33
48
73
73
88
5.0
5.0
5.0
36
36
52
76
76
92
6.0
6.0
6.0
36
36
52
76
76
92
6.0
6.0
6.0
36
36
52
76
76
92
36
36
52
D1
(mm) (l/d)
Dimensions (mm)
Stock
Order Number
HTi10
L1
Hole Depth
L3
Coolant
(Int./Ext.)
Order Number
Drill
Dia.
3 Ext.
3 Int.
6 Int.
6.4
6.5
3 Ext.
3 Int.
6 Int.
6.6
3 Ext.
3 Int.
6 Int.
6.7
3 Ext.
3 Int.
6 Int.
6.0
6.0
6.0
6.8
3 Ext.
3 Int.
6 Int.
76
76
92
6.0
6.0
6.0
3 Ext.
3 Int.
6 Int.
6.9
36
36
52
76
76
92
6.0
6.0
6.0
7.0
3 Ext.
3 Int.
6 Int.
39
39
57
79
79
97
6.0
6.0
6.0
3 Ext.
3 Int.
6 Int.
7.1
39
39
57
79
79
97
6.0
6.0
6.0
7.2
3 Ext.
3 Int.
6 Int.
39
39
57
79
79
97
6.0
6.0
6.0
7.3
3 Ext.
3 Int.
6 Int.
39
39
57
79
79
97
6.0
6.0
6.0
7.35
3 Ext.
3 Int.
6 Int.
39
39
57
79
79
97
6.0
6.0
6.0
7.4
3 Ext.
3 Int.
6 Int.
42
42
62
84
84
104
7.0
7.0
7.0
3 Ext.
3 Int.
6 Int.
7.5
42
42
62
84
84
104
7.0
7.0
7.0
7.6
3 Ext.
3 Int.
6 Int.
42
42
62
84
84
104
7.0
7.0
7.0
3 Ext.
3 Int.
6 Int.
7.7
s
s
s
s
s
s
s
s
*
*
*
MAE0640MB
MAS0640MB
MAS0640LB
MAE0650MB
MAS0650MB
MAS0650LB
MAE0660MB
MAS0660MB
MAS0660LB
MAE0670MB
MAS0670MB
MAS0670LB
MAE0680MB
MAS0680MB
MAS0680LB
MAE0690MB
MAS0690MB
MAS0690LB
MAE0700MB
MAS0700MB
MAS0700LB
MAE0710MB
MAS0710MB
MAS0710LB
MAE0720MB
MAS0720MB
MAS0720LB
MAE0730MB
MAS0730MB
MAS0730LB
MAE0735MB
MAS0735MB
MAS0735LB
MAE0740MB
MAS0740MB
MAS0740LB
MAE0750MB
MAS0750MB
MAS0750LB
MAE0760MB
MAS0760MB
MAS0760LB
MAE0770MB
MAS0770MB
MAS0770LB
L3
L1
D4
42
42
62
84
84
104
7.0
7.0
7.0
42
42
62
84
84
104
7.0
7.0
7.0
42
42
65
84
84
107
7.0
7.0
7.0
42
42
65
84
84
107
7.0
7.0
7.0
42
42
65
84
84
107
7.0
7.0
7.0
42
42
65
84
84
107
7.0
7.0
7.0
42
42
65
84
84
107
7.0
7.0
7.0
48
48
68
90
90
110
8.0
8.0
8.0
48
48
68
90
90
110
8.0
8.0
8.0
48
48
68
90
90
110
8.0
8.0
8.0
48
48
68
90
90
110
8.0
8.0
8.0
48
48
68
90
90
110
8.0
8.0
8.0
48
48
68
90
90
110
8.0
8.0
8.0
48
48
72
90
90
114
8.0
8.0
8.0
48
48
72
90
90
114
8.0
8.0
8.0
CUTTING CONDITIONS
L073
TECHNICAL DATA
N001
DRILLING
3 Ext.
3 Int.
6 Int.
4.9
5.1
Dimensions (mm)
Stock
HTi10
Hole Depth
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
L069
a Specialized

hole accuracy.
MAE/MAS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
a High
Light Alloy
Heat Resistant
Alloy
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D1=3
3<D1< 6
+0.005
0
0
0.006
+0.005
0
0
0.008
6<D1< 10 10<D1< 16
+0.005
0
0
0.009
+0.005
0
0
0.011
3 Ext.
3 Int.
6 Int.
7.8
7.9
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
8.1
3 Ext.
3 Int.
6 Int.
8.2
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
8.3
8.4
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
8.5
8.6
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
DRILLING
8.0
8.7
s
s
s
s
MAE0780MB
MAS0780MB
MAS0780LB
MAE0790MB
MAS0790MB
MAS0790LB
MAE0800MB
MAS0800MB
MAS0800LB
MAE0810MB
MAS0810MB
MAS0810LB
MAE0820MB
MAS0820MB
MAS0820LB
MAE0830MB
MAS0830MB
MAS0830LB
MAE0840MB
MAS0840MB
MAS0840LB
MAE0850MB
MAS0850MB
MAS0850LB
MAE0860MB
MAS0860MB
MAS0860LB
MAE0870MB
MAS0870MB
MAS0870LB
L1
D4
48
48
72
90
90
114
8.0
8.0
8.0
48
48
72
90
90
114
8.0
8.0
8.0
48
48
72
90
90
114
8.0
8.0
8.0
50
50
75
94
94
119
9.0
9.0
9.0
50
50
75
94
94
119
50
50
75
D11
(mm) (l/d)
3 Ext.
3 Int.
6 Int.
8.8
8.9
3 Ext.
3 Int.
6 Int.
9.0
3 Ext.
3 Int.
6 Int.
9.1
3 Ext.
3 Int.
6 Int.
9.0
9.0
9.0
9.2
3 Ext.
3 Int.
6 Int.
94
94
119
9.0
9.0
9.0
3 Ext.
3 Int.
6 Int.
9.21
50
50
75
94
94
119
9.0
9.0
9.0
9.3
3 Ext.
3 Int.
6 Int.
50
50
75
94
94
119
9.0
9.0
9.0
3 Ext.
3 Int.
6 Int.
9.4
50
50
77
94
94
121
9.0
9.0
9.0
9.5
3 Ext.
3 Int.
6 Int.
50
50
77
94
94
121
9.0
9.0
9.0
9.6
3 Ext.
3 Int.
6 Int.
Dimensions (mm)
Stock
Order Number
HTi10
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
HTi10
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
s
s
s
s
s
s
*
*
*
MAE0880MB
MAS0880MB
MAS0880LB
MAE0890MB
MAS0890MB
MAS0890LB
MAE0900MB
MAS0900MB
MAS0900LB
MAE0910MB
MAS0910MB
MAS0910LB
MAE0920MB
MAS0920MB
MAS0920LB
MAE0921MB
MAS0921MB
MAS0921LB
MAE0930MB
MAS0930MB
MAS0930LB
MAE0940MB
MAS0940MB
MAS0940LB
MAE0950MB
MAS0950MB
MAS0950LB
MAE0960MB
MAS0960MB
MAS0960LB
L070
L3
L1
D4
50
50
77
94
94
121
9.0
9.0
9.0
50
50
77
94
94
121
9.0
9.0
9.0
50
50
77
94
94
121
9.0
9.0
9.0
53
53
81
97 10.0
97 10.0
125 10.0
53
53
81
97 10.0
97 10.0
125 10.0
53
53
81
97 10.0
97 10.0
125 10.0
53
53
81
97 10.0
97 10.0
125 10.0
53
53
81
97 10.0
97 10.0
125 10.0
53
53
81
97 10.0
97 10.0
125 10.0
53
53
81
97 10.0
97 10.0
125 10.0
9.8
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
10.0
3 Ext.
3 Int.
6 Int.
10.1
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
10.2
10.3
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
10.4
10.5
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
10.7
3 Ext.
3 Int.
6 Int.
10.8
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
10.9
11.0
3 Ext.
3 Int.
6 Int.
10.6
s
s
r
r
r
r
s
s
r
r
s
s
r
r
r
r
r
r
r
r
s
s
3 Ext.
11.08 3 Int.
6 Int.
*
*
*
MAE0970MB
MAS0970MB
MAS0970LB
MAE0980MB
MAS0980MB
MAS0980LB
MAE0990MB
MAS0990MB
MAS0990LB
MAE1000MB
MAS1000MB
MAS1000LB
MAE1010MB
MAS1010MB
MAS1010LB
MAE1020MB
MAS1020MB
MAS1020LB
MAE1030MB
MAS1030MB
MAS1030LB
MAE1040MB
MAS1040MB
MAS1040LB
MAE1050MB
MAS1050MB
MAS1050LB
MAE1060MB
MAS1060MB
MAS1060LB
MAE1070MB
MAS1070MB
MAS1070LB
MAE1080MB
MAS1080MB
MAS1080LB
MAE1090MB
MAS1090MB
MAS1090LB
MAE1100MB
MAS1100MB
MAS1100LB
MAE1108MB
MAS1108MB
MAS1108LB
D4
53
53
81
97 10.0
97 10.0
125 10.0
53
53
81
97 10.0
97 10.0
125 10.0
53
53
81
97 10.0
97 10.0
125 10.0
53
53
81
97 10.0
97 10.0
125 10.0
55
55
89
D1
(mm) (l/d)
Dimensions (mm)
Stock
HTi10
L1
Hole Depth
L3
Coolant
(Int./Ext.)
Order Number
Drill
Dia.
3 Ext.
3 Int.
6 Int.
11.1
11.2
3 Ext.
3 Int.
6 Int.
11.3
3 Ext.
3 Int.
6 Int.
11.4
3 Ext.
3 Int.
6 Int.
101 11.0
101 11.0
135 11.0
11.5
3 Ext.
3 Int.
6 Int.
55
55
89
101 11.0
101 11.0
135 11.0
3 Ext.
3 Int.
6 Int.
11.6
55
55
89
101 11.0
101 11.0
135 11.0
11.7
3 Ext.
3 Int.
6 Int.
55
55
89
101 11.0
101 11.0
135 11.0
3 Ext.
3 Int.
6 Int.
11.8
55
55
89
101 11.0
101 11.0
135 11.0
11.9
3 Ext.
3 Int.
6 Int.
55
55
89
101 11.0
101 11.0
135 11.0
12.0
3 Ext.
3 Int.
6 Int.
55
55
89
101 11.0
101 11.0
135 11.0
12.1
3 Ext.
3 Int.
6 Int.
55
55
89
101 11.0
101 11.0
135 11.0
12.2
3 Ext.
3 Int.
6 Int.
55
55
89
101 11.0
101 11.0
135 11.0
3 Ext.
3 Int.
6 Int.
12.3
55
55
89
101 11.0
101 11.0
135 11.0
12.4
3 Ext.
3 Int.
6 Int.
60
60
94
106 12.0
106 12.0
140 12.0
3 Ext.
3 Int.
6 Int.
12.5
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
s
s
r
r
r
r
r
r
r
r
s
s
Order Number
MAE1110MB
MAS1110MB
MAS1110LB
MAE1120MB
MAS1120MB
MAS1120LB
MAE1130MB
MAS1130MB
MAS1130LB
MAE1140MB
MAS1140MB
MAS1140LB
MAE1150MB
MAS1150MB
MAS1150LB
MAE1160MB
MAS1160MB
MAS1160LB
MAE1170MB
MAS1170MB
MAS1170LB
MAE1180MB
MAS1180MB
MAS1180LB
MAE1190MB
MAS1190MB
MAS1190LB
MAE1200MB
MAS1200MB
MAS1200LB
MAE1210MB
MAS1210MB
MAS1210LB
MAE1220MB
MAS1220MB
MAS1220LB
MAE1230MB
MAS1230MB
MAS1230LB
MAE1240MB
MAS1240MB
MAS1240LB
MAE1250MB
MAS1250MB
MAS1250LB
L3
L1
D4
60
60
94
106 12.0
106 12.0
140 12.0
60
60
94
106 12.0
106 12.0
140 12.0
60
60
94
106 12.0
106 12.0
140 12.0
60
60
94
106 12.0
106 12.0
140 12.0
60
60
94
106 12.0
106 12.0
140 12.0
60
60
94
106 12.0
106 12.0
140 12.0
60
60
94
106 12.0
106 12.0
140 12.0
60
60
94
106 12.0
106 12.0
140 12.0
60
60
94
106 12.0
106 12.0
140 12.0
60
60
94
106 12.0
106 12.0
140 12.0
65
65
100
115 13.0
115 13.0
150 13.0
65
65
100
115 13.0
115 13.0
150 13.0
65
65
100
115 13.0
115 13.0
150 13.0
65
65
100
115 13.0
115 13.0
150 13.0
65
65
100
115 13.0
115 13.0
150 13.0
CUTTING CONDITIONS
L073
TECHNICAL DATA
N001
DRILLING
3 Ext.
3 Int.
6 Int.
9.7
9.9
Dimensions (mm)
Stock
HTi10
Hole Depth
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
L071
a Specialized

hole accuracy.
MAE/MAS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
a High
Light Alloy
Heat Resistant
Alloy
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D1=3
3<D1< 6
+0.005
0
0
0.006
+0.005
0
0
0.008
6<D1< 10 10<D1< 16
+0.005
0
0
0.009
+0.005
0
0
0.011
3 Ext.
3 Int.
6 Int.
12.6
12.7
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
3 Ext.
12.96 3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
13.0
13.1
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
13.2
13.3
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
12.8
DRILLING
12.9
13.4
r
r
r
r
r
r
r
r
s
s
s
s
r
r
r
r
r
r
r
r
*
*
*
MAE1260MB
MAS1260MB
MAS1260LB
MAE1270MB
MAS1270MB
MAS1270LB
MAE1280MB
MAS1280MB
MAS1280LB
MAE1290MB
MAS1290MB
MAS1290LB
MAE1296MB
MAS1296MB
MAS1296LB
MAE1300MB
MAS1300MB
MAS1300LB
MAE1310MB
MAS1310MB
MAS1310LB
MAE1320MB
MAS1320MB
MAS1320LB
MAE1330MB
MAS1330MB
MAS1330LB
MAE1340MB
MAS1340MB
MAS1340LB
L1
D4
D11
(mm) (l/d)
3 Ext.
3 Int.
6 Int.
13.5
13.6
3 Ext.
3 Int.
6 Int.
13.7
3 Ext.
3 Int.
6 Int.
13.8
3 Ext.
3 Int.
6 Int.
115 13.0
115 13.0
150 13.0
13.9
3 Ext.
3 Int.
6 Int.
65
65
100
115 13.0
115 13.0
150 13.0
3 Ext.
3 Int.
6 Int.
14.0
70
70
110
120 14.0
120 14.0
160 14.0
14.1
3 Ext.
3 Int.
6 Int.
70
70
110
120 14.0
120 14.0
160 14.0
3 Ext.
3 Int.
6 Int.
14.2
70
70
110
120 14.0
120 14.0
160 14.0
14.3
3 Ext.
3 Int.
6 Int.
70
70
110
120 14.0
120 14.0
160 14.0
14.4
3 Ext.
3 Int.
6 Int.
65
65
100
115 13.0
115 13.0
150 13.0
65
65
100
115 13.0
115 13.0
150 13.0
65
65
100
115 13.0
115 13.0
150 13.0
65
65
100
115 13.0
115 13.0
150 13.0
65
65
100
Dimensions (mm)
Stock
Order Number
HTi10
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
HTi10
Hole Depth
Drill
Dia.
Coolant
(Int./Ext.)
r
r
r
r
r
r
r
r
s
s
r
r
r
r
r
r
r
r
*
*
*
MAE1350MB
MAS1350MB
MAS1350LB
MAE1360MB
MAS1360MB
MAS1360LB
MAE1370MB
MAS1370MB
MAS1370LB
MAE1380MB
MAS1380MB
MAS1380LB
MAE1390MB
MAS1390MB
MAS1390LB
MAE1400MB
MAS1400MB
MAS1400LB
MAE1410MB
MAS1410MB
MAS1410LB
MAE1420MB
MAS1420MB
MAS1420LB
MAE1430MB
MAS1430MB
MAS1430LB
MAE1440MB
MAS1440MB
MAS1440LB
L3
L1
D4
70
70
110
120 14.0
120 14.0
160 14.0
70
70
110
120 14.0
120 14.0
160 14.0
70
70
110
120 14.0
120 14.0
160 14.0
70
70
110
120 14.0
120 14.0
160 14.0
70
70
110
120 14.0
120 14.0
160 14.0
70
70
110
120 14.0
120 14.0
160 14.0
72
72
115
130 15.0
130 15.0
173 15.0
72
72
115
130 15.0
130 15.0
173 15.0
72
72
115
130 15.0
130 15.0
173 15.0
72
72
115
130 15.0
130 15.0
173 15.0
L072
TECHNICAL DATA
N001
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
14.6
14.7
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
14.8
14.9
3 Ext.
3 Int.
6 Int.
3 Ext.
14.96 3 Int.
6 Int.
15.0
3 Ext.
3 Int.
6 Int.
15.1
3 Ext.
3 Int.
6 Int.
3 Ext.
3 Int.
6 Int.
14.5
15.2
MAE1450MB
MAS1450MB
MAS1450LB
MAE1460MB
MAS1460MB
MAS1460LB
MAE1470MB
MAS1470MB
MAS1470LB
MAE1480MB
MAS1480MB
MAS1480LB
MAE1490MB
MAS1490MB
MAS1490LB
MAE1496MB
MAS1496MB
MAS1496LB
MAE1500MB
MAS1500MB
MAS1500LB
MAE1510MB
MAS1510MB
MAS1510LB
MAE1520MB
MAS1520MB
MAS1520LB
r
r
r
r
r
r
r
r
r
r
s
s
*
*
*
s
s
r
r
r
r
L1
D4
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
L3
Hole Depth
Order Number
Drill
Dia.
Coolant
(Int./Ext.)
Dimensions (mm)
Stock
VP15TF
Hole Depth
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill
Dia.
72
72
115
130 15.0
130 15.0
173 15.0
3 Ext.
15.3 3 Int.
6 Int.
72
72
115
130 15.0
130 15.0
173 15.0
3 Ext.
15.4 3 Int.
6 Int.
72
72
115
130 15.0
130 15.0
173 15.0
15.5
3 Ext.
3 Int.
6 Int.
72
72
115
130 15.0
130 15.0
173 15.0
3 Ext.
15.6 3 Int.
6 Int.
72
72
115
130 15.0
130 15.0
173 15.0
15.7
3 Ext.
3 Int.
6 Int.
72
72
115
130 15.0
130 15.0
173 15.0
15.8
3 Ext.
3 Int.
6 Int.
72
72
115
130 15.0
130 15.0
173 15.0
15.9
3 Ext.
3 Int.
6 Int.
76
76
120
134 16.0
134 16.0
178 16.0
16.0
3 Ext.
3 Int.
6 Int.
76
76
120
134 16.0
134 16.0
178 16.0
Order Number
r
r
r
r
r
r
*
*
*
r
r
s
s
L3
MAE1530MB
MAS1530MB
MAS1530LB
MAE1540MB
MAS1540MB
MAS1540LB
MAE1550MB
MAS1550MB
MAS1550LB
MAE1560MB
MAS1560MB
MAS1560LB
MAE1570MB
MAS1570MB
MAS1570LB
MAE1580MB
MAS1580MB
MAS1580LB
MAE1590MB
MAS1590MB
MAS1590LB
MAE1600MB
MAS1600MB
MAS1600LB
L1
D4
76
76
120
134 16.0
134 16.0
178 16.0
76
76
120
134 16.0
134 16.0
178 16.0
76
76
120
134 16.0
134 16.0
178 16.0
76
76
120
134 16.0
134 16.0
178 16.0
76
76
120
134 16.0
134 16.0
178 16.0
76
76
120
134 16.0
134 16.0
178 16.0
76
76
120
134 16.0
134 16.0
178 16.0
76
76
120
134 16.0
134 16.0
178 16.0
3.0 6.0 mm
Drill Diameter .118 236
Work Material
N Cast Aluminum Alloy
Die Cast Aluminum Alloy

M
A
E K
Gray Cast Iron
Ductile Cast Iron
N Cast Aluminum Alloy
M
Die Cast Aluminum Alloy
A
S K
Gray Cast Iron
Ductile Cast Iron
Drill Diameter
6.010.0 mm
.240 394
Drill Diameter
10.0 16.0 mm
.398 630
Cutting Speed (SFM)
Feed (IPR)
Cutting Speed (SFM)
Feed (IPR)
Cutting Speed (SFM)
Feed (IPR)
295 (130 460)
.006 (.002 .012)
330 (165 490)
.008 (.002 .012)
395 (195 560)
.010 (.004 .016)
330 (195 490)
.005 (.002 .010)
360 (230 525)
.006 (.002 .010)
425 (260 590)
.008 (.004 .012)
130 (65 195)
.006 (.004 .008)
195 (130 260)
.008 (.004 .012)
260 (195 330)
.012 (.008 .016)
100 (65 130)
.004 (.002 .006)
130 (65 195)
.005 (.002 .008)
195 (130 260)
.008 (.004 .012)
300 (195 490)
.006 (.002 .012)
390 (260 555)
.008 (.004 .012)
490 (330 655)
.010 (.004 .016)
390 (260 555)
.005 (.002 .010)
490 (330 590)
.006 (.002 .010)
525 (390 655)
.008 (.004 .012)
195 (130 260)
.006 (.004 .008)
260 (195 360)
.008 (.004 .012)
330 (230 425)
.012 (.008 .016)
145 (100 195)
.004 (.002 .006)
195 (130 260)
.005 (.002 .008)
260 (195 330)
.008 (.004 .012)
DRILLING
Tool
y HOLE AND DRILL DIAMETERS FOR THREAD

Thread Tapping
Thread Size
Super Burnish Drill

Diameter (D1mm)
M4x0.7
M5x0.8
M6x1.0
M8x1.25
M10x1.5
M12x1.75
M14x2
M16x2
3.3
4.2
5.0
6.8
8.5
10.3
12.0
14.0
Roll Thread Tapping
Hole Diameter Tolerance (mm)

Max.
Min.
Super Burnish Drill

Diameter (D1mm)
3.242
4.134
4.917
6.647
8.376
10.106
11.835
13.835
3.422
4.334
5.153
6.912
8.676
10.441
12.21
14.21
3.65
4.6
5.5
7.35
9.21
11.08
12.96
14.96
Hole Diameter Tolerance (mm)

Max.
Min.
3.65
4.59
5.48
7.34
9.18
11.05
12.92
14.92
3.7
4.66
5.57
7.41
9.28
11.15
13.04
15.04
L073
MNS/MNS DB
aaa
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
a Unique 4 hole, high ow, coolant delivery system prevents
built-up-edge.
a Long drill life and highly efcient drilling of holes in aluminum.
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D 1 =3
3<D1< 6
0
0.014
0
0.006
0
0.018
0
0.008
6<D1< 10 10<D1< 14
0
0.022
0
0.009
0
0.027
0
0.011
a 4.5mm or smaller diameter drills are designed with 2 coolant holes.
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
MNS0300LB
0300X10DB
0300X20DB
0300X30DB
0310LB
0310X10DB
0310X20DB
0310X30DB
0320LB
0320X10DB
0320X20DB
0320X30DB
0330LB
0330X10DB
0330X20DB
0330X30DB
0340LB
0340X10DB
0340X20DB
0340X30DB
0350LB
0350X10DB
0350X20DB
0350X30DB
0360LB
0360X10DB
0360X20DB
0360X30DB
0370LB
0370X10DB
0370X20DB
0370X30DB
3.1
3.2
DRILLING
3.3
3.4
3.5
3.6
3.7
Dimensions (mm)
Stock
L3
L2
L1
D4
Order Number
D1
(mm) (l/d)
TF15
5
10
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
Order Number
D1
(mm) (l/d)
3.0
Dimensions (mm)
Stock
TF15
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
(Note) MNS type can be used for shrink t holders.
33
39
33
42
81
90
3.0
3.0
5
10
Int.
Int.
69
72 120
99 102 150
3.0
3.0
20
30
Int.
Int.
39
46
87
97
4.0
4.0
5
10
Int.
Int.
81
84 132
116 119 167
4.0
4.0
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
MNS0380LB
0380X10DB
0380X20DB
0380X30DB
0390LB
0390X10DB
0390X20DB
0390X30DB
0400LB
0400X10DB
0400X20DB
0400X30DB
0410LB
0410X10DB
0410X20DB
0410X30DB
0420LB
0420X10DB
0420X20DB
0420X30DB
0430LB
0430X10DB
0430X20DB
0430X30DB
0440LB
0440X10DB
0440X20DB
0440X30DB
0450LB
0450X10DB
0450X20DB
0450X30DB
39
46
39
49
87
97
4.0
4.0
81
84 132
116 119 167
4.0
4.0
39
46
39
49
87
97
4.0
4.0
81
84 132
116 119 167
4.0
4.0
39
46
39
49
87
97
4.0
4.0
81
84 132
116 119 167
4.0
4.0
39
46
39
49
87
97
4.0
4.0
81
84 132
116 119 167
4.0
4.0
44
52
39
49
44 92
55 103
4.0
4.0
92
95 143
132 135 183
4.0
4.0
44
52
44 92
55 103
4.0
4.0
92
95 143
132 135 183
4.0
4.0
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
L074
L3
L2
44
52
44 92
55 103
4.0
4.0
92
95 143
132 135 183
4.0
4.0
44
52
L1
D4
44 92
55 103
4.0
4.0
92
95 143
132 135 183
4.0
4.0
44
52
44 92
55 103
4.0
4.0
92
95 143
132 135 183
4.0
4.0
50
59
50 100
62 112
5.0
5.0
104 107 157

149 152 202
5.0
5.0
50
59
50 100
62 112
5.0
5.0
104 107 157

149 152 202
5.0
5.0
50
59
50 100
62 112
5.0
5.0
104 107 157

149 152 202
5.0
5.0
50
59
50 100
62 112
5.0
5.0
104 107 157

149 152 202
5.0
5.0
50
59
50 100
62 112
5.0
5.0
104 107 157

149 152 202
5.0
5.0
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
MNS0460LB
0460X10DB
0460X20DB
0460X30DB
0470LB
0470X10DB
0470X20DB
0470X30DB
0480LB
0480X10DB
0480X20DB
0480X30DB
0490LB
0490X10DB
0490X20DB
0490X30DB
0500LB
0500X10DB
0500X20DB
0500X30DB
0510LB
0510X10DB
0510X20DB
0510X30DB
0520LB
0520X10DB
0520X20DB
0520X30DB
0530LB
0530X10DB
0530X20DB
0530X30DB
0540LB
0540X10DB
0540X20DB
0540X30DB
4.8
4.9
5.0
5.1
5.2
5.3
5.4
55
65
55 105
68 118
5.0
5.0
115 118 168

165 168 218
5.0
5.0
55
65
L1
D4
55 105
68 118
5.0
5.0
115 118 168

165 168 218
5.0
5.0
55
65
55 105
68 118
5.0
5.0
115 118 168

165 168 218
5.0
5.0
55
65
55 105
68 118
5.0
5.0
115 118 168

165 168 218
5.0
5.0
44
65
44 100
68 118
6.0
5.0
115 118 168

165 168 218
5.0
5.0
44
72
44 100
75 127
6.0
6.0
127 130 182

182 185 237
6.0
6.0
44
72
44 100
75 127
6.0
6.0
127 130 182

182 185 237
6.0
6.0
44
72
44 100
75 127
6.0
6.0
127 130 182

182 185 237
6.0
6.0
44
72
44 100
75 127
6.0
6.0
127 130 182

182 185 237
6.0
6.0
Order Number
D1
(mm) (l/d)
D1
(5
l/d) Int.
10
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
MNS0550LB
0550X10DB
0550X20DB
0550X30DB
0560LB
0560X10DB
0560X20DB
0560X30DB
0570LB
0570X10DB
0570X20DB
0570X30DB
0580LB
0580X10DB
0580X20DB
0580X30DB
0590LB
0590X10DB
0590X20DB
0590X30DB
0600LB
0600X10DB
0600X20DB
0600X30DB
0610LB
0610X10DB
0610X20DB
0610X30DB
0620LB
0620X10DB
0620X20DB
0620X30DB
0630LB
0630X10DB
0630X20DB
0630X30DB
5.5
5.6
5.7
5.8
5.9
6.0
6.1
6.2
6.3
L3
L2
44
72
44 100
75 127
6.0
6.0
127 130 182

182 185 237
6.0
6.0
48
78
L1
D4
48 100
81 133
6.0
6.0
138 141 193

198 201 253
6.0
6.0
48
78
48 100
81 133
6.0
6.0
138 141 193

198 201 253
6.0
6.0
48
78
48 100
81 133
6.0
6.0
138 141 193

198 201 253
6.0
6.0
48
78
48 100
81 133
6.0
6.0
138 141 193

198 201 253
6.0
6.0
48
78
48 100
81 133
6.0
6.0
138 141 193

198 201 253
6.0
6.0
52
85
52 109
88 141
7.0
7.0
150 153 206

215 218 271
7.0
7.0
52
85
52 109
88 141
7.0
7.0
150 153 206

215 218 271
7.0
7.0
52
85
52 109
88 141
7.0
7.0
150 153 206

215 218 271
7.0
7.0
CUTTING CONDITIONS
L079
HOW TO USE
L080
TECHNICAL DATA
N001
DRILLING
Int.
Int.
L2
Dimensions (mm)
Stock
TF15
5
10
L3
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
TF15
4.7
Dimensions (mm)
Stock
Order Number
D1
(mm) (l/d)
4.6
Coolant
(Int./Ext.)
Drill Hole
Dia. Depth
L075
MNS/MNS DB
aaa
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
built-up-edge.
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D 1 =3
3<D1< 6
0
0.014
0
0.006
0
0.018
0
0.008
6<D1< 10 10<D1< 14
0
0.022
0
0.009
0
0.027
0
0.011
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
MNS0640LB
0640X10DB
0640X20DB
0640X30DB
0650LB
0650X10DB
0650X20DB
0650X30DB
0660LB
0660X10DB
0660X20DB
0660X30DB
0670LB
0670X10DB
0670X20DB
0670X30DB
0680LB
0680X10DB
0680X20DB
0680X30DB
0690LB
0690X10DB
0690X20DB
0690X30DB
0700LB
0700X10DB
0700X20DB
0700X30DB
0710LB
0710X10DB
0710X20DB
0710X30DB
0720LB
0720X10DB
0720X20DB
0720X30DB
6.5
6.6
6.7
DRILLING
6.8
6.9
7.0
7.1
7.2
Dimensions (mm)
Stock
D4
Order Number
D1
(mm) (l/d)
TF15
5
10
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
Order Number
D1
(mm) (l/d)
6.4
Dimensions (mm)
Stock
TF15
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
52 109
88 141
7.0
7.0
5
10
Int.
Int.
150 153 206

215 218 271
7.0
7.0
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
MNS0730LB
0730X10DB
0730X20DB
0730X30DB
0740LB
0740X10DB
0740X20DB
0740X30DB
0750LB
0750X10DB
0750X20DB
0750X30DB
0760LB
0760X10DB
0760X20DB
0760X30DB
0770LB
0770X10DB
0770X20DB
0770X30DB
0780LB
0780X10DB
0780X20DB
0780X30DB
0790LB
0790X10DB
0790X20DB
0790X30DB
0800LB
0800X10DB
0800X20DB
0800X30DB
0810LB
0810X10DB
0810X20DB
0810X30DB
L3
L2
52
85
52
85
L1
52 109
88 141
7.0
7.0
150 153 206

215 218 271
7.0
7.0
56
91
56 109
94 147
7.0
7.0
161 164 217

231 234 287
7.0
7.0
56
91
56 109
94 147
7.0
7.0
161 164 217

231 234 287
7.0
7.0
56
91
56 109
94 147
7.0
7.0
161 164 217

231 234 287
7.0
7.0
56
91
56 109
94 147
7.0
7.0
161 164 217

231 234 287
7.0
7.0
56
91
56 109
94 147
7.0
7.0
161 164 217

231 234 287
7.0
7.0
60 64 118
98 101 155
8.0
8.0
173 176 230

248 251 305
8.0
8.0
60 64 118
98 101 155
8.0
8.0
173 176 230

248 251 305
8.0
8.0
7.3
7.4
7.5
7.6
7.7
7.8
7.9
8.0
8.1
L076
L3
L2
L1
D4
60 64 118
98 101 155
8.0
8.0
173 176 230

248 251 305
8.0
8.0
60 64 118
98 101 155
8.0
8.0
173 176 230

248 251 305
8.0
8.0
60 64 118
98 101 155
8.0
8.0
173 176 230

248 251 305
8.0
8.0
64 64 118
104 107 161
8.0
8.0
184 187 241

264 267 321
8.0
8.0
64 64 118
104 107 161
8.0
8.0
184 187 241

264 267 321
8.0
8.0
64 64 118
104 107 161
8.0
8.0
184 187 241

264 267 321
8.0
8.0
64 64 118
104 107 161
8.0
8.0
184 187 241

264 267 321
8.0
8.0
64 64 118
104 107 161
8.0
8.0
184 187 241

264 267 321
8.0
8.0
68 72 127
111 114 169
9.0
9.0
196 199 254

281 284 339
9.0
9.0
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
MNS0820LB
0820X10DB
0820X20DB
0820X30DB
0830LB
0830X10DB
0830X20DB
0830X30DB
0840LB
0840X10DB
0840X20DB
0840X30DB
0850LB
0850X10DB
0850X20DB
0850X30DB
0860LB
0860X10DB
0860X20DB
0860X30DB
0870LB
0870X10DB
0870X20DB
0870X30DB
0880LB
0880X10DB
0880X20DB
0880X30DB
0890LB
0890X10DB
0890X20DB
0890X30DB
0900LB
0900X10DB
0900X20DB
0900X30DB
0910LB
0910X10DB
0910X20DB
0910X30DB
0920LB
0920X10DB
0920X20DB
0920X30DB
0930LB
0930X10DB
0930X20DB
0930X30DB
8.4
8.5
8.6
8.7
8.8
8.9
9.0
9.1
9.2
9.3
L1
D4
Order Number
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
5
10
Int.
Int.
20
30
Int.
Int.
Int.
Int.
Int.
20
Int.
Int.
Int.
5
10.3 10
20
Int.
Int.
Int.
MNS0940LB
0940X10DB
0940X20DB
0940X30DB
0950LB
0950X10DB
0950X20DB
0950X30DB
0960LB
0960X10DB
0960X20DB
0960X30DB
0970LB
0970X10DB
0970X20DB
0970X30DB
0980LB
0980X10DB
0980X20DB
0980X30DB
0990LB
0990X10DB
0990X20DB
0990X30DB
1000LB
1000X10DB
1000X20DB
1000X30DB
1010LB
1010X10DB
1010X20DB
1020LB
1020X10DB
1020X20DB
1030LB
1030X10DB
1030X20DB
1040LB
1040X10DB
1040X20DB
1050LB
1050X10DB
1050X20DB
1060LB
1060X10DB
1060X20DB
D1
(mm) (l/d)
68 72 127
111 114 169
9.0
9.0
196 199 254

281 284 339
9.0
9.0
68 72 127
111 114 169
9.0
9.0
196 199 254

281 284 339
9.0
9.0
68 72 127
111 114 169
9.0
9.0
196 199 254

281 284 339
9.0
9.0
68 72 127
111 114 169
9.0
9.0
196 199 254

281 284 339
9.0
9.0
72 72 127
117 120 175
9.0
9.0
207 210 265

297 300 355
9.0
9.0
72 72 127
117 120 175
9.0
9.0
207 210 265

297 300 355
9.0
9.0
72 72 127
117 120 175
9.0
9.0
207 210 265

297 300 355
9.0
9.0
72 72 127
117 120 175
9.0
9.0
207 210 265

297 300 355
9.0
9.0
20
72 72 127
117 120 175
9.0
9.0
10.2 10
207 210 265

297 300 355
9.0
9.0
76 80 136 10.0
124 127 182 10.0
9.4
9.5
9.6
9.7
9.8
9.9
10.0
10.1 10
5
r
r
r
r
r
r
219 222 277 10.0

314 317 372 10.0
10.4 10
20
Int.
Int.
Int.
76 80 136 10.0
124 127 182 10.0
5
10.5 10
20
Int.
Int.
Int.
5
10.6 10
20
Int.
Int.
Int.
219 222 277 10.0

314 317 372 10.0
76 80 136 10.0
124 127 182 10.0
219 222 277 10.0
314 317 372 10.0
r
r
s
s
r
r
L3
L2
L1
D4
76
80 136 10.0
124 127 182 10.0
219 222 277 10.0
314 317 372 10.0
76
80 136 10.0
124 127 182 10.0
219 222 277 10.0
314 317 372 10.0
80
80 136 10.0
130 133 188 10.0
230 233 288 10.0
330 333 388 10.0
80
80 136 10.0
130 133 188 10.0
230 233 288 10.0
330 333 388 10.0
80
80 136 10.0
130 133 188 10.0
230 233 288 10.0
330 333 388 10.0
80
80 136 10.0
130 133 188 10.0
230 233 288 10.0
330 333 388 10.0
80
80 136 10.0
130 133 188 10.0
230 233 288 10.0
330 333 388 10.0
84
88 149 11.0
137 140 201 11.0
242 245 306 11.0
84
88 149 11.0
137 140 201 11.0
242 245 306 11.0
DRILLING
Int.
Int.
L2
Dimensions (mm)
Stock
TF15
5
10
L3
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
TF15
8.3
Dimensions (mm)
Stock
Order Number
D1
(mm) (l/d)
8.2
Coolant
(Int./Ext.)
Drill Hole
Dia. Depth
84
88 149 11.0
137 140 201 11.0
242 245 306 11.0
84
88 149 11.0
137 140 201 11.0
242 245 306 11.0
84
88 149 11.0
137 140 201 11.0
242 245 306 11.0
88
88 149 11.0
143 146 207 11.0
253 256 317 11.0
CUTTING CONDITIONS
L079
HOW TO USE
L080
TECHNICAL DATA
N001
L077
MNS/MNS DB
aaa
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
built-up-edge.
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D 1 =3
3<D1< 6
0
0.014
0
0.006
0
0.018
0
0.008
6<D1< 10 10<D1< 14
0
0.022
0
0.009
0
0.027
0
0.011
20
Int.
Int.
Int.
5
10.9 10
20
Int.
Int.
Int.
20
Int.
Int.
Int.
5
11.1 10
20
Int.
Int.
Int.
5
11.2 10
20
Int.
Int.
Int.
5
20
Int.
Int.
Int.
5
11.4 10
20
Int.
Int.
Int.
20
Int.
Int.
Int.
5
11.6 10
20
Int.
Int.
Int.
20
Int.
Int.
Int.
5
11.8 10
20
Int.
Int.
Int.
MNS1070LB
1070X10DB
1070X20DB
1080LB
1080X10DB
1080X20DB
1090LB
1090X10DB
1090X20DB
1100LB
1100X10DB
1100X20DB
1110LB
1110X10DB
1110X20DB
1120LB
1120X10DB
1120X20DB
1130LB
1130X10DB
1130X20DB
1140LB
1140X10DB
1140X20DB
1150LB
1150X10DB
1150X20DB
1160LB
1160X10DB
1160X20DB
1170LB
1170X10DB
1170X20DB
1180LB
1180X10DB
1180X20DB
20
5
10.8 10
11.0 10
11.3 10
11.5 10
11.7 10
r
r
r
r
r
r
s
s
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
Dimensions (mm)
Stock
TF15
Int.
Int.
Int.
10.7 10
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
Order Number
D1
(mm) (l/d)
DRILLING
Dimensions (mm)
Stock
TF15
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
Order Number
Int.
Int.
Int.
20
Int.
Int.
Int.
5
12.1 10
20
Int.
Int.
Int.
20
Int.
Int.
Int.
5
12.3 10
20
Int.
Int.
Int.
92 96 158 12.0
150 153 215 12.0
265 268 330 12.0
5
12.4 10
20
Int.
Int.
Int.
92 96 158 12.0
150 153 215 12.0
265 268 330 12.0
12.5 10
20
Int.
Int.
Int.
92 96 158 12.0
150 153 215 12.0
265 268 330 12.0
5
12.6 10
20
Int.
Int.
Int.
92 96 158 12.0
150 153 215 12.0
265 268 330 12.0
5
20
Int.
Int.
Int.
12.7 10
96 96 158 12.0
156 159 221 12.0
276 279 341 12.0
5
12.8 10
20
Int.
Int.
Int.
96 96 158 12.0
156 159 221 12.0
276 279 341 12.0
5
20
Int.
Int.
Int.
12.9 10
96 96 158 12.0
156 159 221 12.0
276 279 341 12.0
5
13.0 10
20
Int.
Int.
Int.
MNS1190LB
1190X10DB
1190X20DB
1200LB
1200X10DB
1200X20DB
1210LB
1210X10DB
1210X20DB
1220LB
1220X10DB
1220X20DB
1230LB
1230X10DB
1230X20DB
1240LB
1240X10DB
1240X20DB
1250LB
1250X10DB
1250X20DB
1260LB
1260X10DB
1260X20DB
1270LB
1270X10DB
1270X20DB
1280LB
1280X10DB
1280X20DB
1290LB
1290X10DB
1290X20DB
1300LB
1300X10DB
1300X20DB
L3
L2
L1
D4
D1
(mm) (l/d)
88 88 149 11.0
143 146 207 11.0
253 256 317 11.0
11.9 10
88 88 149 11.0
143 146 207 11.0
253 256 317 11.0
12.0 10
88 88 149 11.0
143 146 207 11.0
253 256 317 11.0
88 88 149 11.0
143 146 207 11.0
253 256 317 11.0
12.2 10
92 96 158 12.0
150 153 215 12.0
265 268 330 12.0
20
5
r
r
s
s
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
s
s
L078
L3
L2
L1
D4
96 96 158 12.0
156 159 221 12.0
276 279 341 12.0
96 96 158 12.0
156 159 221 12.0
276 279 341 12.0
100 104 167 13.0
163 166 229 13.0
288 291 354 13.0
100 104 167 13.0
163 166 229 13.0
288 291 354 13.0
100 104 167 13.0
163 166 229 13.0
288 291 354 13.0
100 104 167 13.0
163 166 229 13.0
288 291 354 13.0
100 104 167 13.0
163 166 229 13.0
288 291 354 13.0
104 104 167 13.0
169 172 235 13.0
299 302 365 13.0
104 104 167 13.0
169 172 235 13.0
299 302 365 13.0
104 104 167 13.0
169 172 235 13.0
299 302 365 13.0
104 104 167 13.0
169 172 235 13.0
299 302 365 13.0
104 104 167 13.0
169 172 235 13.0
299 302 365 13.0
20
Int.
Int.
Int.
5
13.2 10
20
Int.
Int.
Int.
5
13.3 10
20
Int.
Int.
Int.
5
20
Int.
Int.
Int.
5
13.5 10
20
Int.
Int.
Int.
MNS1310LB
1310X10DB
1310X20DB
1320LB
1320X10DB
1320X20DB
1330LB
1330X10DB
1330X20DB
1340LB
1340X10DB
1340X20DB
1350LB
1350X10DB
1350X20DB
13.1 10
13.4 10
r
r
r
r
r
r
r
r
r
r
Dimensions (mm)
Stock
TF15
Order Number
D1
(mm) (l/d)
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
Dimensions (mm)
Stock
TF15
Coolant
(Int./Ext.)
Drill Hole
Dia. Depth
Order Number
20
Int.
Int.
Int.
5
13.7 10
20
Int.
Int.
Int.
108 112 176 14.0

176 179 243 14.0
311 314 378 14.0
5
13.8 10
20
Int.
Int.
Int.
108 112 176 14.0

176 179 243 14.0
311 314 378 14.0
13.9 10
20
Int.
Int.
Int.
108 112 176 14.0

176 179 243 14.0
311 314 378 14.0
5
14.0 10
20
Int.
Int.
Int.
MNS1360LB
1360X10DB
1360X20DB
1370LB
1370X10DB
1370X20DB
1380LB
1380X10DB
1380X20DB
1390LB
1390X10DB
1390X20DB
1400LB
1400X10DB
1400X20DB
L3
L2
L1
D4
D1
(mm) (l/d)
108 112 176 14.0

176 179 243 14.0
311 314 378 14.0
13.6 10
108 112 176 14.0

176 179 243 14.0
311 314 378 14.0
r
r
r
r
r
r
r
r
s
s
L3
L2
L1
D4
112 112 176 14.0

182 185 249 14.0
322 325 389 14.0
112 112 176 14.0
182 185 249 14.0
322 325 389 14.0
112 112 176 14.0
182 185 249 14.0
322 325 389 14.0
112 112 176 14.0
182 185 249 14.0
322 325 389 14.0
112 112 176 14.0
182 185 249 14.0
322 325 389 14.0

Work Material
N Aluminum Alloy Casting

Aluminum Die Casting
Order Number
D1
& 6.1 & 10.0 mm

&.2401 &.3937
& 10.1 & 14.0 mm

&.3976 &.5512
Cutting Speed (SFM)
Feed (IPR)
Cutting Speed (SFM)
Feed (IPR)
Cutting Speed (SFM)
Feed (IPR)
MNS...LB
260 490
.008 .020
330 655
.012 .039
490 820
.012 .039
MNS...DB
195 395
.008 .020
260 490
.012 .039
395 655
.012 .039
MNS...LB
260 490
.006 .012
330 655
.008 .016
490 655
.008 .016
MNS...DB
195 395
.006 .012
260 490
.008 .016
395 655
.008 .016
Wrought Aluminum Alloy
(Note)
When using the drill with a length over l/d 10, it is necessary to use a prep holes as the pilot. (If no prep-hole is used then drill breakage can
occur)
For pilot hole drilling, Mitsubishi Materials MNS-LB, MAE-MB or MAS-MB drill is recommended.
*
*
HOW TO USE
L080
TECHNICAL DATA
N001
DRILLING
Drill Diameter
& 3.0 & 6.0 mm
&.1181 &.2362
L079
MNS
y OPERATIONAL GUIDANCE FOR THE MNS...LB DRILL
Drill Length
Drill Installation
Installation Tolerance
Adjusting Screw
Drill Holding
NG
D1

A > D1 x 1.5
Runout < .001
Coolant Handling
Thin Workpiece
Interrupted Cutting
Spindle Through
Coolant Type
Coolant
Inducer Type
One process
a ne mesh lter as a
efcient ow. Regular
coolant exchange is
recommended.
If Bending
Occurs
NG
Requires prior
machining
Support
the Workpiece
Good
70 - 1015 PSI (0.5 - 7MPa).
Burring and Workpiece Chipping
DRILLING
Stepped Holes

processes.
order.
L080

breaking through.
xAdd a chamfer.
Good
zLower the feed
when drilling the
interrupted part.
zSpot face with an

end mill prior to
drilling.
MNS DB
aaa
y OPERATIONAL GUIDANCE FOR THE MNS...DB DRILL

z Use a drill with a larger (atter) point angle than the MNS...DB type.
Mitsubishi type MNS-LB, MAE-MB or MAS-MB drill is recommended.
x Ensure a high precision hole is drilled for the pilot.
(Adjust the pilot hole depth according to the length of the MNS...DB type.)


zAfter drilling, lower the cutting revolution about .039-.079 inch short of
120 inch/min.
.008-.012 IPR.
y 1. Spot facing



z Use a drill with a larger (atter) point angle than the super long type.
Mitsubishi type MNS-LB, MAE-MB or MAS-MB drill is recommended.
(Adjust the pilot hole depth according to the length of the super long type.)
DRILLING
FLAT FACE DRILLING


inch/min.
L081
a High web strength compliments a stablizing double margin design.
a Long drill life and no-peck drilling in harderned steel up to HRC55.
MHS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D1=3
3<D1< 6
+0.010
0.002
+0.010
0.002
0
0.008
6<D1< 10 10<D1< 12
+0.010
0.005
0
0.009
+0.010
0.008
0
0.011
3.0
3.1
3.2
DRILLING
3.3
3.4
3.5
3.6
3.7
4
10
Int.
Int.
17
27
Int.
Int.
4
10
Int.
Int.
17
26
Int.
Int.
4
10
Int.
Int.
16
25
Int.
Int.
3
9
Int.
Int.
16
25
Int.
Int.
3
9
Int.
Int.
15
24
Int.
Int.
3
9
Int.
Int.
14
23
Int.
Int.
3
9
Int.
Int.
14
Int.
22
31
Int.
Int.
3
8
Int.
Int.
14
Int.
22
30
Int.
Int.
L3
L2
MHS0300L020B 19.0 20
0300L040B 39.0 40
0300L060B 59.0 60
0300L090B 89.0 90
0310L020B 19.5 20
0310L040B 39.5 40
0310L060B 59.5 60
0310L090B 89.5 90
0320L020B 19.5 20
0320L040B 39.5 40
0320L060B 59.5 60
0320L090B 89.5 90
0330L020B 19.5 20
0330L040B 39.5 40
0330L060B 59.5 60
0330L090B 89.5 90
0340L020B 19.5 20
0340L040B 39.5 40
0340L060B 59.5 60
0340L090B 89.5 90
0350L020B 19.5 20
0350L040B 39.5 40
0350L060B 59.5 60
0350L090B 89.5 90
0360L020B 20.0 20
0360L040B 40.0 40
0360L060B 60.0 60
0360L090B 90.0 90
0360L120B 120.0 120
0370L020B 20.0 20
0370L040B 40.0 40
0370L060B 60.0 60
0370L090B 90.0 90
0370L120B 120.0 120
L1
D4
D1
(mm) (l/d)
70
90
4.0
4.0
3
8
Int.
Int.
110
140
4.0
4.0
13
Int.
4.0
4.0
Int.
Int.
70
90
21
29
4.0
4.0
Int.
Int.
110
140
3
8
13
Int.
70
90
4.0
4.0
21
28
Int.
Int.
110
140
4.0
4.0
2
7
Int.
Int.
70
90
4.0
4.0
12
Int.
4.0
4.0
Int.
Int.
110
140
20
27
4.0
4.0
Int.
Int.
70
90
2
7
12
Int.
110
140
4.0
4.0
19
26
Int.
Int.
70
90
4.0
4.0
2
7
Int.
Int.
110
140
4.0
4.0
11
Int.
4.0
4.0
Int.
Int.
70
90
19
26
4.0
Int.
Int.
110
2
6
140
170
4.0
4.0
11
Int.
4.0
4.0
Int.
Int.
70
90
18
25
4.0
2
6
Int.
Int.
110
140
170
4.0
4.0
11
Int.
18
24
Int.
Int.
3.8
3.9
4.0
4.1
4.2
4.3
4.4
Dimensions (mm)
Stock
VP15TF
Order Number
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
(Note 1) MHS type can be used for shrink t holders.

(Note 2) Use the shortest type in the respective diameter as a pilot drill.
Order Number
MHS0380L020B
0380L040B
0380L060B
0380L090B
0380L120B
0390L020B
0390L040B
0390L060B
0390L090B
0390L120B
0400L020B
0400L040B
0400L060B
0400L090B
0400L120B
0410L020B
0410L040B
0410L060B
0410L090B
0410L120B
0420L020B
0420L040B
0420L060B
0420L090B
0420L120B
0430L020B
0430L040B
0430L060B
0430L090B
0430L120B
0440L020B
0440L040B
0440L060B
0440L090B
0440L120B
L082
L3
L2
L1
D4
20.0
40.0
20
40
70
90
4.0
4.0
60.0
60 110
4.0
90.0 90 140
120.0 120 170
4.0
4.0
20.0
40.0
20
40
70
90
4.0
4.0
60.0
60 110
4.0
90.0 90 140
120.0 120 170
4.0
4.0
20.0
40.0
20
40
70
90
4.0
4.0
60.0
60 110
4.0
90.0 90 140
120.0 120 170
4.0
4.0
18.5
38.5
20
40
70
90
6.0
6.0
58.5
60 110
6.0
88.5 90 140
118.5 120 170
6.0
6.0
18.5
38.5
20
40
70
90
6.0
6.0
58.5
60 110
6.0
88.5 90 140
118.5 120 170
6.0
6.0
18.5
38.5
20
40
70
90
6.0
6.0
58.5
60 110
6.0
88.5 90 140
118.5 120 170
6.0
6.0
18.5
38.5
20
40
70
90
6.0
6.0
58.5
60 110
6.0
88.5 90 140
118.5 120 170
6.0
6.0
4.6
4.7
4.8
4.9
5.0
5.1
5.2
2
6
Int.
Int.
10
Int.
17
24
Int.
Int.
2
6
Int.
Int.
10
Int.
17
Int.
23
30
Int.
Int.
2
6
Int.
Int.
10
Int.
16
Int.
23
29
Int.
Int.
1
6
Int.
Int.
10
Int.
16
Int.
22
29
Int.
Int.
1
5
Int.
Int.
10
Int.
16
Int.
22
28
Int.
Int.
1
5
Int.
Int.
Int.
15
Int.
21
27
Int.
Int.
3
9
Int.
Int.
15
Int.
21
27
Int.
Int.
3
9
Int.
Int.
15
Int.
20
26
Int.
Int.
MHS0450L020B
0450L040B
0450L060B
0450L090B
0450L120B
0460L020B
0460L040B
0460L060B
0460L090B
0460L120B
0460L150B
0470L020B
0470L040B
0470L060B
0470L090B
0470L120B
0470L150B
0480L020B
0480L040B
0480L060B
0480L090B
0480L120B
0480L150B
0490L020B
0490L040B
0490L060B
0490L090B
0490L120B
0490L150B
0500L020B
0500L040B
0500L060B
0500L090B
0500L120B
0500L150B
0510L030B
0510L060B
0510L090B
0510L120B
0510L150B
0520L030B
0520L060B
0520L090B
0520L120B
0520L150B
L3
L2
L1
D4
D1
(mm) (l/d)
18.5
38.5
20
40
70
90
6.0
6.0
3
9
Int.
Int.
58.5
60 110
6.0
14
Int.
88.5 90 140
118.5 120 170
6.0
6.0
20
26
Int.
Int.
3
9
Int.
Int.
14
Int.
20
25
Int.
Int.
3
8
Int.
Int.
14
Int.
Int.
Int.
19.0
39.0
20
40
70
90
6.0
6.0
59.0
60 110
6.0
89.0
90 140
6.0
119.0 120 170

149.0 150 200
6.0
6.0
5.3
5.4
19.0
39.0
20
40
70
90
6.0
6.0
59.0
60 110
6.0
89.0
90 140
6.0
19
25
119.0 120 170

149.0 150 200
6.0
6.0
3
8
Int.
Int.
14
Int.
19
24
Int.
Int.
3
8
Int.
Int.
19.0
39.0
20
40
70
90
6.0
6.0
59.0
60 110
6.0
89.0
90 140
6.0
119.0 120 170

149.0 150 200
6.0
6.0
5.5
5.6
5.7
13
Int.
19.0
39.0
20
40
70
90
6.0
6.0
19
24
Int.
Int.
59.0
60 110
6.0
89.0
90 140
6.0
3
8
Int.
Int.
119.0 120 170

149.0 150 200
6.0
6.0
13
Int.
18
23
Int.
Int.
3
8
Int.
Int.
5.8
19.0
39.0
20
40
70
90
6.0
6.0
59.0
60 110
6.0
89.0
90 140
6.0
13
Int.
119.0 120 170

149.0 150 200
6.0
6.0
18
23
Int.
Int.
6.0
6.0
2
7
Int.
Int.
5.9
29.5
59.5
30 80
60 110
89.5
90 140
6.0
12
Int.
119.5 120 170

149.5 150 200
6.0
6.0
17
22
Int.
Int.
6.0
6.0
2
7
Int.
Int.
12
Int.
17
22
Int.
Int.
29.5
59.5
30 80
60 110
89.5
90 140
6.0
119.5 120 170

149.5 150 200
6.0
6.0
6.0
6.1
Dimensions (mm)
Stock
VP15TF
Coolant
(Int./Ext.)
Order Number
Drill Hole
Dia. Depth
Order Number
MHS0530L030B
0530L060B
0530L090B
0530L120B
0530L150B
0540L030B
0540L060B
0540L090B
0540L120B
0540L150B
0550L030B
0550L060B
0550L090B
0550L120B
0550L150B
0560L030B
0560L060B
0560L090B
0560L120B
0560L150B
0570L030B
0570L060B
0570L090B
0570L120B
0570L150B
0580L030B
0580L060B
0580L090B
0580L120B
0580L150B
0590L030B
0590L060B
0590L090B
0590L120B
0590L150B
0600L030B
0600L060B
0600L090B
0600L120B
0600L150B
0610L030B
0610L060B
0610L090B
0610L120B
0610L150B
L3
L2
L1
D4
29.5
59.5
30 80
60 110
89.5
90 140
6.0
119.5 120 170

149.5 150 200
6.0
6.0
6.0
6.0
29.5
59.5
30 80
60 110
6.0
6.0
89.5
90 140
6.0
119.5 120 170

149.5 150 200
6.0
6.0
29.5
59.5
30 80
60 110
6.0
6.0
89.5
90 140
6.0
119.5 120 170

149.5 150 200
6.0
6.0
30.0
60.0
30 80
60 110
6.0
6.0
90.0
90 140
6.0
120.0 120 170

150.0 150 200
6.0
6.0
30.0
60.0
30 80
60 110
6.0
6.0
90.0
90 140
6.0
120.0 120 170

150.0 150 200
6.0
6.0
30.0
60.0
30 80
60 110
6.0
6.0
90.0
90 140
6.0
120.0 120 170

150.0 150 200
6.0
6.0
30.0
60.0
30 80
60 110
6.0
6.0
90.0
90 140
6.0
120.0 120 170

150.0 150 200
6.0
6.0
30.0
60.0
30 80
60 110
90.0
90 140
6.0
120.0 120 170

150.0 150 200
6.0
6.0
DRILLING
4.5
Dimensions (mm)
Stock
VP15TF
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill Hole
Dia. Depth
6.0
6.0
28.5
58.5
30 80
60 110
8.0
8.0
88.5
90 140
8.0
118.5 120 170

148.5 150 200
8.0
8.0
CUTTING CONDITIONS
L089
HOW TO USE
L089
TECHNICAL DATA
N001
L083
MHS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D1=3
3<D1< 6
+0.010
0.002
+0.010
0.002
0
0.008
6<D1< 10 10<D1< 12
+0.010
0.005
0
0.009
+0.010
0.008
0
0.011
6.2
6.3
DRILLING
6.4
6.5
6.6
6.7
2
7
Int.
Int.
12
Int.
17
21
Int.
Int.
2
7
Int.
Int.
12
Int.
16
21
Int.
Int.
2
7
Int.
Int.
11
Int.
16
21
Int.
Int.
2
6
Int.
Int.
11
Int.
16
20
Int.
Int.
2
6
Int.
Int.
11
Int.
16
Int.
20
28
Int.
Int.
2
6
Int.
Int.
11
Int.
15
Int.
20
27
Int.
Int.
MHS0620L030B
0620L060B
0620L090B
0620L120B
0620L150B
0630L030B
0630L060B
0630L090B
0630L120B
0630L150B
0640L030B
0640L060B
0640L090B
0640L120B
0640L150B
0650L030B
0650L060B
0650L090B
0650L120B
0650L150B
0660L030B
0660L060B
0660L090B
0660L120B
0660L150B
0660L200B
0670L030B
0670L060B
0670L090B
0670L120B
0670L150B
0670L200B
L3
L2
L1
28.5
58.5
30 80
60 110
88.5
90 140
8.0
118.5 120 170

148.5 150 200
8.0
8.0
D4
D1
(mm) (l/d)
8.0
8.0
2
6
Int.
Int.
11
Int.
15
Int.
19
27
Int.
Int.
2
6
Int.
Int.
10
Int.
15
Int.
8.0
8.0
19
26
Int.
Int.
2
6
Int.
Int.
10
Int.
14
Int.
Int.
Int.
28.5
58.5
30 80
60 110
8.0
8.0
88.5
90 140
8.0
118.5 120 170

148.5 150 200
8.0
8.0
28.5
58.5
30 80
60 110
88.5
90 140
8.0
118.5 120 170

148.5 150 200
8.0
8.0
6.8
6.9
7.0
28.5
58.5
30 80
60 110
8.0
8.0
88.5
90 140
8.0
19
26
118.5 120 170

148.5 150 200
8.0
8.0
2
6
Int.
Int.
10
Int.
14
Int.
29.0
59.0
30 80
60 110
89.0
8.0
8.0
7.1
90 140
8.0
8.0
19
26
Int.
Int.
119.0 120 170

149.0 150 200
199.0 200 250
8.0
8.0
2
6
Int.
Int.
10
Int.
14
Int.
18
25
Int.
Int.
29.0
59.0
30 80
60 110
8.0
8.0
89.0
90 140
8.0
119.0 120 170
8.0
149.0 150 200

199.0 200 250
8.0
8.0
7.2
Dimensions (mm)
Stock
VP15TF
Order Number
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)

Order Number
MHS0680L030B
0680L060B
0680L090B
0680L120B
0680L150B
0680L200B
0690L030B
0690L060B
0690L090B
0690L120B
0690L150B
0690L200B
0700L030B
0700L060B
0700L090B
0700L120B
0700L150B
0700L200B
0710L030B
0710L060B
0710L090B
0710L120B
0710L150B
0710L200B
0720L030B
0720L060B
0720L090B
0720L120B
0720L150B
0720L200B
L084
L3
L2
L1
29.0
59.0
30 80
60 110
89.0
D4
8.0
8.0
90 140
8.0
119.0 120 170
8.0
149.0 150 200

199.0 200 250
8.0
8.0
29.0
59.0
30 80
60 110
89.0
8.0
8.0
90 140
8.0
119.0 120 170
8.0
149.0 150 200

199.0 200 250
8.0
8.0
29.0
59.0
30 80
60 110
89.0
8.0
8.0
90 140
8.0
119.0 120 170
8.0
149.0 150 200

199.0 200 250
8.0
8.0
29.5
59.5
30 80
60 110
89.5
8.0
8.0
90 140
8.0
119.5 120 170
8.0
149.5 150 200

199.5 200 250
8.0
8.0
29.5
59.5
30 80
60 110
8.0
8.0
89.5
90 140
8.0
119.5 120 170
8.0
149.5 150 200

199.5 200 250
8.0
8.0
7.4
2
6
Int.
Int.
10
Int.
14
Int.
18
25
Int.
Int.
1
6
Int.
Int.
10
Int.
14
Int.
18
24
Int.
Int.
1
5
Int.
Int.
Int.
13
Int.
17
24
Int.
Int.
1
5
Int.
Int.
Int.
7.6 13
Int.
17
Int.
24
30
Int.
Int.
1
5
Int.
Int.
Int.
7.7 13
Int.
17
Int.
23
30
Int.
Int.
7.5
1
5
Int.
Int.
Int.
7.8 13
Int.
17
Int.
23
30
Int.
Int.
1
5
Int.
Int.
Int.
13
Int.
16
Int.
23
29
Int.
Int.
7.9
MHS0730L030B
0730L060B
0730L090B
0730L120B
0730L150B
0730L200B
0740L030B
0740L060B
0740L090B
0740L120B
0740L150B
0740L200B
0750L030B
0750L060B
0750L090B
0750L120B
0750L150B
0750L200B
0760L030B
0760L060B
0760L090B
0760L120B
0760L150B
0760L200B
0760L250B
0770L030B
0770L060B
0770L090B
0770L120B
0770L150B
0770L200B
0770L250B
0780L030B
0780L060B
0780L090B
0780L120B
0780L150B
0780L200B
0780L250B
0790L030B
0790L060B
0790L090B
0790L120B
0790L150B
0790L200B
0790L250B
L2
L1
29.5
59.5
30 80
60 110
89.5
D4
D1
(mm) (l/d)
8.0
8.0
1
5
Int.
Int.
s
s
90 140
8.0
Int.
119.5 120 170
8.0
8.0 12
Int.
149.5 150 200

199.5 200 250
8.0
8.0
16
Int.
22
29
Int.
Int.
2
8
Int.
Int.
29.5
59.5
30 80
60 110
8.0
8.0
89.5
90 140
8.0
119.5 120 170
8.0
149.5 150 200

199.5 200 250
8.0
8.0
29.5
59.5
30 80
60 110
8.0
8.0
89.5
90 140
8.0
119.5 120 170
8.0
149.5 150 200

199.5 200 250
8.0
8.0
8.1
8.2
12
Int.
16
Int.
22
28
Int.
Int.
2
8
Int.
Int.
12
Int.
16
Int.
22
28
Int.
Int.
2
8
Int.
Int.
12
Int.
15
Int.
30.0
60.0
30 80
60 110
8.0
8.0
90.0
90 140
8.0
120.0 120 170
8.0
150.0 150 200
8.0
200.0 200 250

250.0 250 300
8.0
8.0
21
27
Int.
Int.
2
8
Int.
Int.
12
Int.
15
Int.
21
27
Int.
Int.
2
8
Int.
Int.
30.0
60.0
30 80
60 110
8.0
8.0
90.0
90 140
8.0
120.0 120 170
8.0
150.0 150 200
8.0
200.0 200 250

250.0 250 300
8.0
8.0
30.0
60.0
30 80
60 110
8.0
8.0
90.0
90 140
8.0
120.0 120 170
8.0
150.0 150 200

200.0 200 250
250.0 250 300
8.3
8.4
11
Int.
15
Int.
Int.
Int.
8.0
21
27
8.0
8.0
2
8
Int.
Int.
30.0
60.0
30 80
60 110
8.0
8.0
90.0
90 140
8.0
120.0 120 170
8.0
150.0 150 200
8.0
200.0 200 250

250.0 250 300
8.0
8.0
8.5
8.6
8.7
Dimensions (mm)
Stock
VP15TF
L3
Coolant
(Int./Ext.)
Order Number
Drill Hole
Dia. Depth
11
Int.
15
Int.
21
26
Int.
Int.
2
8
Int.
Int.
11
Int.
15
Int.
20
26
Int.
Int.
r
r
Order Number
MHS0800L030B
0800L060B
0800L090B
0800L120B
0800L150B
0800L200B
0800L250B
0810L040B
0810L090B
0810L120B
0810L150B
0810L200B
0810L250B
0820L040B
0820L090B
0820L120B
0820L150B
0820L200B
0820L250B
0830L040B
0830L090B
0830L120B
0830L150B
0830L200B
0830L250B
0840L040B
0840L090B
0840L120B
0840L150B
0840L200B
0840L250B
0850L040B
0850L090B
0850L120B
0850L150B
0850L200B
0850L250B
0860L040B
0860L090B
0860L120B
0860L150B
0860L200B
0860L250B
0870L040B
0870L090B
0870L120B
0870L150B
0870L200B
0870L250B
L3
L2
L1
30.0
60.0
30 80
60 110
90.0
D4
8.0
8.0
90 140
8.0
120.0 120 170
8.0
150.0 150 200
8.0
200.0 200 250

250.0 250 300
8.0
8.0
38.5
88.5
40 100 10.0
90 150 10.0
118.5 120 180 10.0

148.5 150 210 10.0
198.5 200 260 10.0
248.5 250 310 10.0
38.5
88.5
40 100 10.0
90 150 10.0
118.5 120 180 10.0

148.5 150 210 10.0
198.5 200 260 10.0
248.5 250 310 10.0
38.5
88.5
40 100 10.0
90 150 10.0
118.5 120 180 10.0

148.5 150 210 10.0
198.5 200 260 10.0
248.5 250 310 10.0
38.5
88.5
40 100 10.0
90 150 10.0
118.5 120 180 10.0

148.5 150 210 10.0
198.5 200 260 10.0
248.5 250 310 10.0
38.5
88.5
40 100 10.0
90 150 10.0
118.5 120 180 10.0

148.5 150 210 10.0
198.5 200 260 10.0
248.5 250 310 10.0
39.0
89.0
DRILLING
7.3
Dimensions (mm)
Stock
VP15TF
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill Hole
Dia. Depth
40 100 10.0
90 150 10.0
119.0 120 180 10.0

149.0 150 210 10.0
199.0 200 260 10.0
249.0 250 310 10.0
39.0
89.0
40 100 10.0
90 150 10.0
119.0 120 180 10.0

149.0 150 210 10.0
199.0 200 260 10.0
249.0 250 310 10.0
CUTTING CONDITIONS
L089
HOW TO USE
L089
TECHNICAL DATA
N001
L085
MHS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D1=3
3<D1< 6
+0.010
0.002
+0.010
0.002
0
0.008
6<D1< 10 10<D1< 12
+0.010
0.005
0
0.009
+0.010
0.008
0
0.011
2
8
8.8
8.9
s
s
11
Int.
14
Int.
20
26
Int.
Int.
s
s
2
7
Int.
Int.
11
Int.
14
Int.
20
25
Int.
Int.
2
7
Int.
Int.
11
Int.
14
Int.
20
25
Int.
Int.
2
7
Int.
Int.
11
Int.
9.1 14
Int.
19
Int.
25
30
Int.
Int.
2
7
Int.
Int.
9.0
DRILLING
Int.
Int.
10
Int.
9.2 14
Int.
19
Int.
25
30
Int.
Int.
r
r
MHS0880L040B
0880L090B
0880L120B
0880L150B
0880L200B
0880L250B
0890L040B
0890L090B
0890L120B
0890L150B
0890L200B
0890L250B
0900L040B
0900L090B
0900L120B
0900L150B
0900L200B
0900L250B
0910L040B
0910L090B
0910L120B
0910L150B
0910L200B
0910L250B
0910L300B
0920L040B
0920L090B
0920L120B
0920L150B
0920L200B
0920L250B
0920L300B
L3
L2
L1
D4
39.0
89.0
40 100 10.0
90 150 10.0
D1
(mm) (l/d)
2
7
Int.
Int.
r
r
119.0 120 180 10.0
10
Int.
149.0 150 210 10.0
9.3 14
Int.
199.0 200 260 10.0

249.0 250 310 10.0
19
Int.
24
30
Int.
Int.
2
7
Int.
Int.
39.0
89.0
40 100 10.0
90 150 10.0
119.0 120 180 10.0
149.0 150 210 10.0
10
Int.
199.0 200 260 10.0

249.0 250 310 10.0
9.4 13
Int.
19
Int.
40 100 10.0
90 150 10.0
24
29
Int.
Int.
119.0 120 180 10.0
2
7
Int.
Int.
10
Int.
9.5 13
Int.
18
Int.
24
29
Int.
Int.
Int.
Int.
199.5 200 260 10.0
2
7
249.5 250 310 10.0

299.5 300 360 10.0
10
Int.
9.6 13
Int.
18
Int.
24
29
Int.
Int.
2
7
Int.
Int.
199.5 200 260 10.0

249.5 250 310 10.0
299.5 300 360 10.0
10
Int.
9.7 13
Int.
18
Int.
23
28
Int.
Int.
39.0
89.0
149.0 150 210 10.0

199.0 200 260 10.0
249.0 250 310 10.0
39.5
89.5
40 100 10.0
90 150 10.0
119.5 120 180 10.0

149.5 150 210 10.0
39.5
89.5
40 100 10.0
90 150 10.0
119.5 120 180 10.0

149.5 150 210 10.0
Dimensions (mm)
Stock
VP15TF
Order Number
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)

Order Number
MHS0930L040B
0930L090B
0930L120B
0930L150B
0930L200B
0930L250B
0930L300B
0940L040B
0940L090B
0940L120B
0940L150B
0940L200B
0940L250B
0940L300B
0950L040B
0950L090B
0950L120B
0950L150B
0950L200B
0950L250B
0950L300B
0960L040B
0960L090B
0960L120B
0960L150B
0960L200B
0960L250B
0960L300B
0970L040B
0970L090B
0970L120B
0970L150B
0970L200B
0970L250B
0970L300B
L086
L3
L2
L1
D4
39.5
89.5
40 100 10.0
90 150 10.0
119.5 120 180 10.0

149.5 150 210 10.0
199.5 200 260 10.0
249.5 250 310 10.0
299.5 300 360 10.0
39.5
89.5
40 100 10.0
90 150 10.0
119.5 120 180 10.0

149.5 150 210 10.0
199.5 200 260 10.0
249.5 250 310 10.0
299.5 300 360 10.0
39.5
89.5
40 100 10.0
90 150 10.0
119.5 120 180 10.0

149.5 150 210 10.0
199.5 200 260 10.0
249.5 250 310 10.0
299.5 300 360 10.0
40.0
90.0
40 100 10.0
90 150 10.0
120.0 120 180 10.0

150.0 150 210 10.0
200.0 200 260 10.0
250.0 250 310 10.0
300.0 300 360 10.0
40.0
90.0
40 100 10.0
90 150 10.0
120.0 120 180 10.0

150.0 150 210 10.0
200.0 200 260 10.0
250.0 250 310 10.0
300.0 300 360 10.0
9.8
Int.
Int.
s
s
10
Int.
13
Int.
18
Int.
23
28
Int.
Int.
2
7
Int.
Int.
10
Int.
13
Int.
18
Int.
23
28
Int.
Int.
1
6
Int.
Int.
Int.
10.0 12
Int.
17
Int.
22
27
Int.
Int.
1
6
Int.
Int.
9.9
Int.
10.1 12
Int.
17
Int.
22
27
Int.
Int.
1
6
Int.
Int.
Int.
10.2 12
Int.
17
Int.
22
27
Int.
Int.
1
6
Int.
Int.
Int.
10.3 12
Int.
17
Int.
22
26
Int.
Int.
1
6
Int.
Int.
Int.
10.4 12
Int.
17
Int.
21
26
Int.
Int.
r
r
MHS0980L040B
0980L090B
0980L120B
0980L150B
0980L200B
0980L250B
0980L300B
0990L040B
0990L090B
0990L120B
0990L150B
0990L200B
0990L250B
0990L300B
1000L040B
1000L090B
1000L120B
1000L150B
1000L200B
1000L250B
1000L300B
1010L040B
1010L090B
1010L120B
1010L150B
1010L200B
1010L250B
1010L300B
1020L040B
1020L090B
1020L120B
1020L150B
1020L200B
1020L250B
1020L300B
1030L040B
1030L090B
1030L120B
1030L150B
1030L200B
1030L250B
1030L300B
1040L040B
1040L090B
1040L120B
1040L150B
1040L200B
1040L250B
1040L300B
L2
L1
D4
40.0
90.0
40 100 10.0
90 150 10.0
D1
(mm) (l/d)
1
6
Int.
Int.
s
s
120.0 120 180 10.0
Int.
150.0 150 210 10.0
10.5 12
Int.
200.0 200 260 10.0
16
Int.
250.0 250 310 10.0

300.0 300 360 10.0
21
26
Int.
Int.
1
6
Int.
Int.
40.0
90.0
40 100 10.0
90 150 10.0
120.0 120 180 10.0
Int.
150.0 150 210 10.0
10.6 12
Int.
200.0 200 260 10.0
16
Int.
250.0 250 310 10.0

300.0 300 360 10.0
21
26
Int.
Int.
40 100 10.0
90 150 10.0
1
6
Int.
Int.
120.0 120 180 10.0
Int.
150.0 150 210 10.0
10.7 11
Int.
200.0 200 260 10.0
16
Int.
250.0 250 310 10.0

300.0 300 360 10.0
21
25
Int.
Int.
1
6
Int.
Int.
40.0
90.0
38.5
88.5
40 100 12.0
90 150 12.0
118.5 120 180 12.0
Int.
148.5 150 210 12.0
10.8 11
Int.
198.5 200 260 12.0
16
Int.
248.5 250 310 12.0

298.5 300 360 12.0
21
25
Int.
Int.
1
6
Int.
Int.
38.5
88.5
40 100 12.0
90 150 12.0
118.5 120 180 12.0
Int.
148.5 150 210 12.0
10.9 11
Int.
198.5 200 260 12.0
16
Int.
248.5 250 310 12.0

298.5 300 360 12.0
20
25
Int.
Int.
40 100 12.0
90 150 12.0
1
6
Int.
Int.
118.5 120 180 12.0
Int.
148.5 150 210 12.0
11.0 11
Int.
198.5 200 260 12.0
16
Int.
248.5 250 310 12.0

298.5 300 360 12.0
20
25
Int.
Int.
1
6
Int.
Int.
38.5
88.5
38.5
88.5
40 100 12.0
90 150 12.0
Dimensions (mm)
Stock
VP15TF
L3
Coolant
(Int./Ext.)
Order Number
Drill Hole
Dia. Depth
118.5 120 180 12.0
Int.
148.5 150 210 12.0
11.1 11
Int.
198.5 200 260 12.0
15
Int.
248.5 250 310 12.0

298.5 300 360 12.0
20
24
Int.
Int.
r
r
Order Number
MHS1050L040B
1050L090B
1050L120B
1050L150B
1050L200B
1050L250B
1050L300B
1060L040B
1060L090B
1060L120B
1060L150B
1060L200B
1060L250B
1060L300B
1070L040B
1070L090B
1070L120B
1070L150B
1070L200B
1070L250B
1070L300B
1080L040B
1080L090B
1080L120B
1080L150B
1080L200B
1080L250B
1080L300B
1090L040B
1090L090B
1090L120B
1090L150B
1090L200B
1090L250B
1090L300B
1100L040B
1100L090B
1100L120B
1100L150B
1100L200B
1100L250B
1100L300B
1110L040B
1110L090B
1110L120B
1110L150B
1110L200B
1110L250B
1110L300B
L3
L2
L1
D4
38.5
88.5
40 100 12.0
90 150 12.0
118.5 120 180 12.0

148.5 150 210 12.0
198.5 200 260 12.0
248.5 250 310 12.0
298.5 300 360 12.0
39.0
89.0
40 100 12.0
90 150 12.0
119.0 120 180 12.0

149.0 150 210 12.0
199.0 200 260 12.0
249.0 250 310 12.0
299.0 300 360 12.0
39.0
89.0
40 100 12.0
90 150 12.0
119.0 120 180 12.0

149.0 150 210 12.0
199.0 200 260 12.0
249.0 250 310 12.0
299.0 300 360 12.0
39.0
89.0
40 100 12.0
90 150 12.0
119.0 120 180 12.0

149.0 150 210 12.0
199.0 200 260 12.0
249.0 250 310 12.0
299.0 300 360 12.0
39.0
89.0
40 100 12.0
90 150 12.0
119.0 120 180 12.0

149.0 150 210 12.0
199.0 200 260 12.0
249.0 250 310 12.0
299.0 300 360 12.0
39.0
89.0
40 100 12.0
90 150 12.0
DRILLING
2
7
Dimensions (mm)
Stock
VP15TF
D1
(mm) (l/d)
Coolant
(Int./Ext.)
Drill Hole
Dia. Depth
119.0 120 180 12.0

149.0 150 210 12.0
199.0 200 260 12.0
249.0 250 310 12.0
299.0 300 360 12.0
39.5
89.5
40 100 12.0
90 150 12.0
119.5 120 180 12.0

149.5 150 210 12.0
199.5 200 260 12.0
249.5 250 310 12.0
299.5 300 360 12.0
CUTTING CONDITIONS
L089
HOW TO USE
L089
TECHNICAL DATA
N001
L087
MHS
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
D1 Tolerance
(mm)
D4 Tolerance
(mm)
METRIC STANDARD
D1=3
3<D1< 6
+0.010
0.002
0
0.006
+0.010
0.002
0
0.008
6<D1< 10 10<D1< 12
+0.010
0.005
0
0.009
+0.010
0.008
0
0.011
DRILLING
1
5
Int.
Int.
r
r
Int.
11.2 11
Int.
15
Int.
20
24
Int.
Int.
1
5
Int.
Int.
Int.
11.3 11
Int.
15
Int.
20
24
Int.
Int.
1
5
Int.
Int.
Int.
11.4 11
Int.
15
Int.
19
24
Int.
Int.
1
5
Int.
Int.
Int.
11.5 10
Int.
15
Int.
19
24
Int.
Int.
1
5
Int.
Int.
Int.
11.6 10
Int.
15
Int.
19
23
Int.
Int.
r
r
MHS1120L040B
1120L090B
1120L120B
1120L150B
1120L200B
1120L250B
1120L300B
1130L040B
1130L090B
1130L120B
1130L150B
1130L200B
1130L250B
1130L300B
1140L040B
1140L090B
1140L120B
1140L150B
1140L200B
1140L250B
1140L300B
1150L040B
1150L090B
1150L120B
1150L150B
1150L200B
1150L250B
1150L300B
1160L040B
1160L090B
1160L120B
1160L150B
1160L200B
1160L250B
1160L300B
L3
L2
L1
D4
39.5
89.5
40 100 12.0
90 150 12.0
D1
(mm) (l/d)
1
5
Int.
Int.
r
r
119.5 120 180 12.0
Int.
149.5 150 210 12.0
11.7 10
Int.
199.5 200 260 12.0
15
Int.
249.5 250 310 12.0

299.5 300 360 12.0
19
23
Int.
Int.
1
5
Int.
Int.
39.5
89.5
40 100 12.0
90 150 12.0
119.5 120 180 12.0
Int.
149.5 150 210 12.0
11.8 10
Int.
199.5 200 260 12.0
14
Int.
249.5 250 310 12.0

299.5 300 360 12.0
19
23
Int.
Int.
40 100 12.0
90 150 12.0
1
5
Int.
Int.
119.5 120 180 12.0
Int.
149.5 150 210 12.0
11.9 10
Int.
199.5 200 260 12.0
14
Int.
249.5 250 310 12.0

299.5 300 360 12.0
19
23
Int.
Int.
1
5
Int.
Int.
39.5
89.5
39.5
89.5
40 100 12.0
90 150 12.0
119.5 120 180 12.0
Int.
149.5 150 210 12.0
12.0 10
Int.
199.5 200 260 12.0
14
Int.
249.5 250 310 12.0

299.5 300 360 12.0
18
22
Int.
Int.
40.0
90.0
Dimensions (mm)
Stock
VP15TF
Order Number
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)
D1
(mm) (l/d)
Dimensions (mm)
Stock
VP15TF
Drill Hole
Dia. Depth
Coolant
(Int./Ext.)

Order Number
MHS1170L040B
1170L090B
1170L120B
1170L150B
1170L200B
1170L250B
1170L300B
1180L040B
1180L090B
1180L120B
1180L150B
1180L200B
1180L250B
1180L300B
1190L040B
1190L090B
1190L120B
1190L150B
1190L200B
1190L250B
1190L300B
1200L040B
1200L090B
1200L120B
1200L150B
1200L200B
1200L250B
1200L300B
40 100 12.0
90 150 12.0
120.0 120 180 12.0

150.0 150 210 12.0
200.0 200 260 12.0
250.0 250 310 12.0
300.0 300 360 12.0
L088
L3
L2
L1
D4
40.0
90.0
40 100 12.0
90 150 12.0
120.0 120 180 12.0

150.0 150 210 12.0
200.0 200 260 12.0
250.0 250 310 12.0
300.0 300 360 12.0
40.0
90.0
40 100 12.0
90 150 12.0
120.0 120 180 12.0

150.0 150 210 12.0
200.0 200 260 12.0
250.0 250 310 12.0
300.0 300 360 12.0
40.0
90.0
40 100 12.0
90 150 12.0
120.0 120 180 12.0

150.0 150 210 12.0
200.0 200 260 12.0
250.0 250 310 12.0
300.0 300 360 12.0
40.0
90.0
40 100 12.0
90 150 12.0
120.0 120 180 12.0

150.0 150 210 12.0
200.0 200 260 12.0
250.0 250 310 12.0
300.0 300 360 12.0

Drill Diameter
D1
Work Material
& 3.0 & 6.0 mm

&.1181 &.2362
& 6.1 & 10.0 mm

&.2401 &.3937
& 10.1 & 12.0 mm

&.3976 &.4724
Conditions
Hardness
Cutting Speed
(SFM)
Feed
(IPR)
Cutting Speed
(SFM)
Feed
(IPR)
Cutting Speed
(SFM)
Feed
(IPR)
40HRC
130 230
.004 .008
130 230
.006 .010
130 230
.008 .012
40 50HRC
65 165
.002 .006
65 165
.004 .008
65 165
.006 .010
50 55HRC
30 100
.001 .004
30 100
.002 .006
30 100
.002 .008
H
Heat-treated steel
Pre-hardened steel
(Note 1) When using the drill with a length over l/d 10, it is necessary to use a prep holes as the pilot. (If no prep-hole is used then drill
breakage can occur)
(Note 2) Use the shortest ute drill in the respective size as a pilot drill.
y OPERATIONAL GUIDANCE FOR THE MHS DRILL
Drill Length
Drill Installation
Installation Tolerance
Adjusting Screw
Drill Holding
NG
D1

A > D1 x 1.5
Runout < .001
Coolant Handling
Thin Workpiece
Interrupted Cutting
Coolant
Inducer Type
One process
a ne mesh lter as a
efcient ow. Regular
coolant exchange is
recommended.

70 - 1015 PSI (0.5 - 7 MPa).
Stepped Holes

processes.
order.
If Bending
Occurs
NG
Good
zLower the feed
when drilling the
interrupted part.
Requires prior
machining
Support
the Workpiece
Good
zSpot face with an

end mill prior to
drilling.
DRILLING
Spindle Through
Coolant Type
Burring and Workpiece Chipping

breaking through.
xAdd a chamfer.
TECHNICAL DATA
N001
L089
MHS
y OPERATIONAL GUIDANCE FOR THE MHS LONG TYPE DRILL (L/D > 10)
FLAT FACE DRILLING
z Use a drill with a larger (atter) point angle than the MHS drill.
Use the shortest ute possible.
(Adjust the pilot hole depth according to the length of the MHS drill.)


DRILLING
z After drilling, lower the cutting revolution about .039-.079 inch short of
120 inch/min.
.008-.012 IPR.
y 1. Spot facing


L090

z Use a drill with a larger (atter) point angle than the super long type.
Use the shortest ute possible.
(Adjust the pilot hole depth according to the length of the super long type.)


inch/min.
MHE (Drill for WHEEL HUB)

y Designed for machining of wheel hub.
y Drill diameter range : From .394" to .591"
y Drill length : For 1 x D1 (D1:Drill diameter)
y Non stock, produced as special order only.
FEATURES
Lower cutting edge height for
the prevention of work hardening
Low helix angle

for high tool rigidity and
stable hole accuracy.
Small point angle for

stable hole accuracy
Narrow ute
for better chip control.

& .394" & .591"
Work Material
Carbon Steel
Hardness
Cutting Speed
(SFM)
Feed
(IPR)
<180HB
245 (195 295)
.010 (.006 .012)
(Note) The above cutting conditions should be used as a guide and need to be adjusted according to the machine rigidity,
workpiece clamping and shape.
: &.500" x 4" x &.500"
: Hub
: Carbon steel
: 195 SFM
: .006 IPR
: WSO
MHE
Competitor
Number of holes
CUTTING PERFORMANCE
DRILLING
Tool
Component
Workpiece
Cutting speed
Feed
Coolant
Chip Geometry
Hole Accuracy
Drill diameter (inch)
: New product
: 1st regrind
: 2nd regrind
Drilled hole diameter tolerance within .591!inch!
Cutting length (ft)
: 3rd regrind
Chip breaking properties

The workpiece surface is not damaged due to
the ne chips that were generated.
L091
a For
MCS
CFRP
high accuracy and efcient drilling of CFRP.

diamond coating produces, excellent wear resistance and smooth hole surface.
a Unique
CFRP with
Aluminum stack
.1719< D< .2362 .2510< D< .3937 .4380< D< .5512

D1 Tolerance
0
.00071
0
.00031
(inch)
D4 Tolerance
(inch)
0
13
0
.00106
0
.00043
D4(h6)
D1(h8)
INCH STANDARD
0
.00087
0
.00035
L3
L2
L1
(Note) MCS type can be used for shrink t holders.
D1
Coolant
(l/d)
(inch)
DD2010
Hole Depth
.1719
.1915
.2510
.3125
.3760
.3765
.4380
.5010
Dimensions (inch)
Stock
Drill Dia.
3
3
Int.
Int.
Int.
Int.
Int.
Int.
3
3
Int.
Int.
Order Number
MCS01719X3DB
01915X3DB
02510X3DB
03125X3DB
03760X3DB
03765X3DB
04380X3DB
05010X3DB
L3
L2
L1
D4
.906
1.063
1.102
1.102
2.559
2.559
.2362
.2362
1.299
1.614
3.071
.3150
1.575
1.614
3.071
.3150
1.772
1.811
3.425
.3937
1.772
1.811
3.425
.3937
2.087
2.284
2.126
2.323
3.937
4.134
.4724
.5512
DRILLING
Work
Material
L092
CFRP
CFRP with Aluminum stack
Drill Dia.
D1 (inch)
Cutting Speed
(SFM)
Feed
(IPR)
Cutting Speed
(SFM)
Feed
(IPR)
.1719
.1915
280
(165 390)
.0016
(.0012 .0032)
180
(130 230)
.0016
(.0012 .0024)
.2510
.3125
310
(195 425)
.0020
(.0012 .0039)
215
(165 260)
.0020
(.0012 .0028)
.3760
.3765
310
(195 425)
.0028
(.0016 .0047)
215
(165 260)
.0024
(.0016 .0032)
.4380
330
(195 490)
.0039
(.0020 .0059)
230
(165 330)
.0028
(.0020 .0039)
.5010
330
(195 490)
.0039
(.0020 .0059)
230
(165 330)
.0032
(.0020 .0047)
TECHNICAL DATA
N001
Memo
L093
DRILLING (INDEXABLE TYPE)

a Wavy cutting edge design for good chip control.
a Highly rigid clamping system offers stability and reliability for small hole drilling.
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
D1 Tolerance
(mm)
D1
METRIC STANDARD
D1=10
10<D1<14
0
0.022
0
0.027
D4
Carbon Steel
Alloy Steel
140
STAW
L3
L2
L1
L3
37
L2
L1
D4
Wrench
(l/d)
STAWSN1000S16
47
95
16
10.4
zTIP06F
STAWMN1000S16
57
67
115
16
zTIP06F
STAWSN1050S16
37
47
95
16
zTIP06F
STAWMN1050S16
57
67
115
16
zTIP06F
10.5
10.9
STAWSN1100S16
41
52
100
16
zTIP06F
STAWMN1100S16
66
77
125
16
zTIP06F
11.0
11.4
STAWSN1150S16
STAWMN1150S16
41
52
100
16
zTIP06F
16
zTIP06F
11.5
12.0
STAWSN1200S16
66
45
77
57
125
105
16
zTIP06F
DRILLING
11.9
12.4
STAWMN1200S16
STAWSN1250S16
70
45
82
57
130
105
16
16
zTIP06F
zTIP06F
12.5
12.9
STAWMN1250S16
STAWSN1300S16
70
49
82
62
130
110
16
16
zTIP06F
xTIP08W
13.0
13.4
STAWMN1300S16
74
87
135
16
xTIP08W
STAWSN1350S16
49
62
110
16
xTIP08W
STAWMN1350S16
74
87
135
16
xTIP08W
13.5
13.9
Insert
10.0
Order Number
Order Number
10.0
10.1
10.2
10.3
10.4
10.5
10.6
10.7
10.8
10.9
11.0
11.1
11.2
11.3
11.4
11.5
11.6
11.7
11.8
11.9
12.0
12.1
12.2
12.3
12.4
12.5
12.6
12.7
12.8
12.9
13.0
13.1
13.2
13.3
13.4
13.5
13.6
13.7
13.8
13.9
STAWN1000TH
STAWN1010TH
STAWN1020TH
STAWN1030TH
STAWN1040TH
STAWN1050TH
STAWN1060TH
STAWN1070TH
STAWN1080TH
STAWN1090TH
STAWN1100TH
STAWN1110TH
STAWN1120TH
STAWN1130TH
STAWN1140TH
STAWN1150TH
STAWN1160TH
STAWN1170TH
STAWN1180TH
STAWN1190TH
STAWN1200TH
STAWN1210TH
STAWN1220TH
STAWN1230TH
STAWN1240TH
STAWN1250TH
STAWN1260TH
STAWN1270TH
STAWN1280TH
STAWN1290TH
STAWN1300TH
STAWN1310TH
STAWN1320TH
STAWN1330TH
STAWN1340TH
STAWN1350TH
STAWN1360TH
STAWN1370TH
STAWN1380TH
STAWN1390TH
(Note) Please contact us for any geometry that is not in this catalogue (e.g. different diameter and length).
L094
Stock
Drill
Dia.
D1
(mm)
VP15TF
D1
(mm)
Dimensions (mm)
Holder
Stock
Drill Dia.
Range
Hole Depth
yHOLDERS
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
1D(h
1 8)
S1

<Note: One insert in one case>
VP15TF
D1
L2
S1
10.0
10.1
3.8
3.8
4.6
4.6
10.2
3.8
4.6
10.3
10.4
3.8
3.8
4.6
4.6
10.5
10.6
4.0
4.0
4.8
4.8
10.7
4.0
4.8
10.8
10.9
4.0
4.0
4.8
4.8
11.0
11.1
4.2
4.2
5.1
5.1
11.2
4.2
5.1
11.3
11.4
4.2
4.2
5.1
5.1
11.5
11.6
4.4
4.4
5.3
5.3
11.7
4.4
5.3
11.8
11.9
4.4
4.4
5.3
5.3
12.0
12.1
4.6
4.6
5.5
5.5
12.2
4.6
5.5
12.3
12.4
4.6
4.6
5.5
5.5
12.5
12.6
4.8
4.8
5.8
5.8
12.7
4.8
5.8
12.8
12.9
4.8
4.8
5.8
5.8
13.0
13.1
4.9
4.9
6.0
6.0
13.2
4.9
6.0
13.3
13.4
4.9
4.9
6.0
6.0
13.5
13.6
5.1
5.1
6.2
6.2
13.7
5.1
6.2
13.8
13.9
5.1
5.1
6.2
6.2
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Applicable Holder
STAWSN1000S16
STAWMN1000S16
STAWSN1050S16
STAWMN1050S16
STAWSN1100S16
STAWMN1100S16
STAWSN1150S16
STAWMN1150S16
STAWSN1200S16
STAWMN1200S16
DRILLING
STAWN1000TH
1010TH
1020TH
1030TH
1040TH
1050TH
1060TH
1070TH
1080TH
1090TH
1100TH
1110TH
1120TH
1130TH
1140TH
1150TH
1160TH
1170TH
1180TH
1190TH
1200TH
1210TH
1220TH
1230TH
1240TH
1250TH
1260TH
1270TH
1280TH
1290TH
1300TH
1310TH
1320TH
1330TH
1340TH
1350TH
1360TH
1370TH
1380TH
1390TH
L2
Dimensions (mm)
Stock
Order Number
140
INSERTS
STAWSN1250S16
STAWMN1250S16
STAWSN1300S16
STAWMN1300S16
STAWSN1350S16
STAWMN1350S16
CUTTING CONDITIONS
L096
HOW TO USE
L097
L095
DRILLING (INDEXABLE TYPE)
STAW
Drill Diameter D1
Work Material
Conditions Cutting speed

(SFM)
Hardness
DRILLING
L096
& 13 . 0 & 13.9mm
Feed
(IPR)
Cutting speed
(SFM)
Feed
(IPR)
< 180HB
260
(195 330)
.008
(.006 .010)
295
(230 360)
.010
(.008 .012)
180 280HB
260
(195 330)
.008
(.006 .010)
295
(230 360)
.010
(.008 .012)
280 350HB
230
(195 295)
.008
(.006 .010)
260
(195 330)
.010
(.008 .012)
Stainless Steel
< 200HB
130
(100 165)
.005
(.004 .006)
165
(130 195)
.006
(.005 .007)
Cast Iron
Tensile Strength
< 350MPa
260
(195 330)
.008
(.006 .010)
295
(230 360)
.010
(.008 .012)
Ductile Cast Iron
Tensile Strength
< 450MPa
230
(195295)
.008
(.006 .010)
260
(195 330)
.010
(.008 .012)
Mild Steel
Carbon Steel
Alloy Steel
& 10 .0 & 12.9mm
NOTES ON USE
Stopper
y INSERT INSTALLATION
1. Before inserting the insert into the holder, ensure that there are no foreign
objects or dirt in the holder slot or slit. Clean using compressed air if
necessary.
Internal
screw
Holder slot
Slit
en
op
k
loc
2. Use the wrench provided to loosen the inner screw to open the tip of the
holder, then place the insert into the holder slot as shown in gure 1.
Ensure that the wrench is rmly in contact with the base of the inner screw
head when tightening.
Fig. 1
lock
4. Check there is no gap between the bottom of the insert and holder slot.
OK
Alignment mark
open
3. After the insert has been set in the holder slot, tighten the inner screw while
pushing the insert lightly into the pocket as shown in gure 2 to securely
clamp and locate the insert.
Ensure that the wrench is rmly in contact with the base of the inner screw head
when tightening.
Fig. 2
NO
No clearance
Clearance
SPARE PARTS
Tool Holder Number
STAWS/MN1000S16
STAWS/MN1050S16
STAWS/MN1100S16
STAWS/MN1150S16
STAWS/MN1200S16
STAWS/MN1250S16
STAWS/MN1300S16
STAWS/MN1350S16
*1
Pack Order Number

(Internal screw & stopper)
*1
Internal Screw
Stopper
WS203107TPS-35LH
WS203107TPS
WS35LH
WS203107TPS-35LH
WS203107TPS
WS35LH
WS203108TPS-35LH
WS203108TPS
WS35LH
WS203108TPS-35LH
WS203108TPS
WS35LH
WS203108TPS-35LH
WS203108TPS
WS35LH
WS203108TPS-35LH
WS203108TPS
WS35LH
WS253909TPS-45LH
WS253909TPS-45LH
WS253909TPS
WS253909TPS
WS45LH
WS45LH
DRILLING
(Note) Poor or incorrect clamping of inserts can cause poor drilling performance and/or drill breakage.
Therefore ensure that the alignment marks on both the body and insert are aligned when setting.
When machining, use safety guards and eye protection.
Clamp Torque (lbf-in) : WS203107TPS=8.9, WS253909TPS=18, WS35LH=11, WS45LH=18

*12 The
parts are packaged internal screw, stopper and operation manual.
* Please
replace the parts in accordance with the operation manual.
L097
DRILLING(INDEXABLE INSERT TYPE)

a Wavy
TAW
Carbon Steel
Alloy Steel
Hardened
Steel
cutting edge design for good chip control.

geometry for accurate insert location.
a Serration
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
INCH STANDARD
L/D=3
Internal Coolant
Stock
Order Number
L3
L2
L1
D4
Insert
Drill Dia.
x
D8
Insert Screw
Wrench
D1
Plate
Anti-seize
Lubricant
(inch)
Order Number
TAWSNH0036
2.008 2.638 4.513
.625 1/8-27
WS254012T zTKY08D WPT4405 MK1KS
.5625
TAWNH0036T
0037
2.126 2.953 4.828
.625 1/8-27
.5781
TAWNH0037T
.5938
TAWNH0038T
0039
2.126 2.953 4.953
.750 1/8-27
.6094
TAWNH0039T
TAWN0040T
TAWNH0040T
TAWN0041T
TAWNH0041T
TAWN0042T
TAWNH0042T
TAWN0043T
TAWNH0043T
TAWN0044T
TAWNH0044T
TAWN0045T
TAWNH0045T
TAWN0046T
TAWNH0046T
TAWN0047T
TAWNH0047T
TAWN0048T
TAWNH0048T
TAWN0049T
TAWNH0049T
TAWN0050T
TAWNH0050T
TAWN0051T
TAWNH0051T
TAWN0052T
TAWNH0052T
TAWN0053T
TAWNH0053T
TAWN0054T
TAWNH0054T
TAWN0055T
TAWNH0055T
TAWN0056T
TAWNH0056T
.6250
TAWSN 0041
2.283 3.150 5.150
.750 1/8-27
.6406
.6563
0044
2.402 3.346 5.346
.750 1/8-27
.6719
.6875
0045
2.559 3.543 5.543
.750 1/8-27
.7031
0046
2.559 3.543 5.793 1.000 1/8-27
.7188
DRILLING
.7344
0049
2.677 3.898 6.148 1.000 1/8-27
WS304517T xTKY10T WPT4405 MK1KS
.7500
.7656
.7813
0051
2.835 3.898 6.148 1.000 1/8-27
.7969
.8125
0054
2.953 3.898 6.148 1.000 1/8-27
.8281
.8438
.8594
0056
3.110 4.094 6.344 1.000 1/8-27
.8750
WS254013T=18, WS254014T=18, WS254015T=18,
* Clamp Torque (lbf-in) : WS254012T=18,
WS254016T=18, WS304517T=31, WS304518T=31, WS355520T=49
L098
Stock
VP15TF
Dimensions (inch)
Holder
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
L3
L2
L1
D4
Insert
Drill Dia.
x
D8
Insert Screw
Wrench
D1
Plate
Anti-seize
Lubricant
3.228 4.094 6.344 1.000 1/8-27
.9063
.9219
.9375
0061
3.386 4.331 6.706 1.250 1/4-18
.9531
.9688
0100
3.465 4.331 6.706 1.250 1/4-18
.9844
1.0000
1.0156
0102
3.622 4.528 6.903 1.250 1/4-18
1.0313
1.0469
0105
3.701 4.528 6.903 1.250 1/4-18
WS406024T xTKY25T WPT4405 MK1KS 1.0625
1.0781
1.0938
0107
3.819 4.724 7.099 1.250 1/4-18
1.1094
1.1250
0110
3.937 4.921 7.296 1.250 1/4-18
1.1563
1.1719
0112
4.094 4.921 7.296 1.250 1/4-18
TAWN0057T
TAWNH0057T
TAWN0058T
TAWNH0058T
TAWN0059T
TAWNH0059T
TAWN0060T
TAWNH0060T
TAWN0061T
TAWNH0061T
TAWN0062T
TAWNH0062T
TAWN0063T
TAWNH0063T
TAWN0100T
TAWNH0100T
TAWN0101T
TAWNH0101T
TAWN0102T
TAWNH0102T
TAWN0103T
TAWNH0103T
TAWN0104T
TAWNH0104T
TAWN0105T
TAWNH0105T
TAWN0106T
TAWNH0106T
TAWN0107T
TAWNH0107T
TAWN0108T
TAWNH0108T
TAWN0109T
TAWNH0109T
TAWN0110T
TAWNH0110T
TAWN0111T
TAWNH0111T
TAWN0112T
TAWNH0112T
(inch)
.8906
TAWSN0059
Stock
Order Number
1.1875
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
DRILLING
Stock
Order Number
VP15TF
Dimensions (inch)
Holder
a
a
a
* Clamp Torque (lbf-in) : WS355521T=49, WS406023T=75, WS406024T=75, WS508026T=110, WS508027T=110
INSERTS
L104
CUTTING CONDITIONS
L111
HOW TO USE
L111
TECHNICAL DATA
N001
L099

a Wavy
TAW
Carbon Steel
Alloy Steel
Hardened
Steel

a Serration
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
INCH STANDARD
L/D=5
Internal Coolant
Stock
Order Number
L3
L2
L1
D4
Insert
Drill Dia.
x
D8
Insert Screw
Wrench
D1
Plate
Anti-seize
Lubricant
(inch)
Order Number
TAWMNH0036
3.150 3.819 5.694
.625 1/8-27
.5625
TAWNH0036T
0037
3.346 4.134 6.009
.625 1/8-27
.5781
TAWNH0037T
.5938
TAWNH0038T
0039
3.346 4.134 6.134
.750 1/8-27
.6094
TAWNH0039T
TAWN0040T
TAWNH0040T
TAWN0041T
TAWNH0041T
TAWN0042T
TAWNH0042T
TAWN0043T
TAWNH0043T
TAWN0044T
TAWNH0044T
TAWN0045T
TAWNH0045T
TAWN0046T
TAWNH0046T
TAWN0047T
TAWNH0047T
TAWN0048T
TAWNH0048T
TAWN0049T
TAWNH0049T
TAWN0050T
TAWNH0050T
TAWN0051T
TAWNH0051T
TAWN0052T
TAWNH0052T
TAWN0053T
TAWNH0053T
TAWN0054T
TAWNH0054T
TAWN0055T
TAWNH0055T
TAWN0056T
TAWNH0056T
.6250
TAWMN0041
3.583 4.528 6.528
.750 1/8-27
.6406
.6563
0044
3.780 4.724 6.724
.750 1/8-27
.6719
.6875
0045
4.016 4.921 6.921
.750 1/8-27
.7031
0046
4.016 4.921 7.171 1.000 1/8-27
.7188
DRILLING
.7344
0049
4.213 5.276 7.526 1.000 1/8-27
.7500
.7656
.7813
0051
4.449 5.472 7.722 1.000 1/8-27
.7969
.8125
0054
4.646 5.472 7.722 1.000 1/8-27
.8281
.8438
.8594
0056
4.882 5.669 7.919 1.000 1/8-27
.8750
WS254013T=18, WS254014T=18, WS254015T=18, WS254016T=18,
WS304517T=31, WS304518T=31, WS355520T=49
L100
Stock
VP15TF
Dimensions (inch)
Holder
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
L3
L2
L1
D4
Insert
Drill Dia.
x
D8
Insert Screw
Wrench
D1
Plate
Anti-seize
Lubricant
5.079 6.063
8.313 1.000 1/8-27
.9063
.9219
.9375
0061
5.315 6.299
8.674 1.250 1/4-18
.9531
.9688
0100
5.512 6.496
8.871 1.250 1/4-18
.9844
1.0000
1.0156
0102
5.748 6.693
9.068 1.250 1/4-18
1.0313
1.0469
0105
5.945 6.890
9.265 1.250 1/4-18
1.0781
1.0938
0107
6.181 7.087
9.462 1.250 1/4-18
1.1094
1.1250
0110
6.378 7.283
9.658 1.250 1/4-18
1.1563
1.1719
0112
6.575 7.677 10.052 1.250 1/4-18
TAWN0057T
TAWNH0057T
TAWN0058T
TAWNH0058T
TAWN0059T
TAWNH0059T
TAWN0060T
TAWNH0060T
TAWN0061T
TAWNH0061T
TAWN0062T
TAWNH0062T
TAWN0063T
TAWNH0063T
TAWN0100T
TAWNH0100T
TAWN0101T
TAWNH0101T
TAWN0102T
TAWNH0102T
TAWN0103T
TAWNH0103T
TAWN0104T
TAWNH0104T
TAWN0105T
TAWNH0105T
TAWN0106T
TAWNH0106T
TAWN0107T
TAWNH0107T
TAWN0108T
TAWNH0108T
TAWN0109T
TAWNH0109T
TAWN0110T
TAWNH0110T
TAWN0111T
TAWNH0111T
TAWN0112T
TAWNH0112T
(inch)
.8906
TAWMN0059
Stock
Order Number
1.1875
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
DRILLING
Stock
Order Number
VP15TF
Dimensions (inch)
Holder
a
a
a
INSERTS
L104
CUTTING CONDITIONS
L111
HOW TO USE
L111
TECHNICAL DATA
N001
L101

a Wavy
TAW
Carbon Steel
Alloy Steel
Hardened
Steel

a Serration
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
INCH STANDARD
L/D=8
Internal Coolant
Stock
Order Number
L3
L2
L1
D4
Insert
Drill Dia.
x
D8
Insert Screw
Wrench
D1
Plate
Anti-seize
Lubricant
(inch)
Order Number
TAWLNH0036
4.803 5.394 7.268 .625 1/8-27
.5625
TAWNH0036T
0037
5.118 5.827 7.701 .625 1/8-27
.5781
TAWNH0037T
.5938
TAWNH0038T
0039
5.118 5.827 7.827 .750 1/8-27
.6094
TAWNH0039T
TAWN0040T
TAWNH0040T
TAWN0041T
TAWNH0041T
TAWN0042T
TAWNH0042T
TAWN0043T
TAWNH0043T
TAWN0044T
TAWNH0044T
TAWN0045T
TAWNH0045T
TAWN0046T
TAWNH0046T
TAWN0047T
TAWNH0047T
TAWN0048T
TAWNH0048T
TAWN0049T
TAWNH0049T
TAWN0050T
TAWNH0050T
TAWN0051T
TAWNH0051T
TAWN0052T
TAWNH0052T
TAWN0053T
TAWNH0053T
TAWN0054T
TAWNH0054T
TAWN0055T
TAWNH0055T
TAWN0056T
TAWNH0056T
.6250
TAWLN0041
5.433 6.220 8.220 .750 1/8-27
.6406
.6563
0044
5.748 6.535 8.535 .750 1/8-27
.6719
.6875
0045
6.063 6.850 8.850 .750 1/8-27
.7031
0046
6.063 6.850 9.102 1.000 1/8-27
.7188
DRILLING
.7344
0049
6.378 7.283 9.535 1.000 1/8-27
.7500
.7656
.7813
0051
6.693 7.598 9.850 1.000 1/8-27
.7969
.8125
0054
7.008 7.953 10.205 1.000 1/8-27
.8281
.8438
.8594
0056
7.323 8.268 10.520 1.000 1/8-27
.8750
WS254013T=18, WS254014T=18, WS254015T=18, WS254016T=18,
WS304517T=31, WS304518T=31, WS355520T=49
L102
Stock
VP15TF
Dimensions (inch)
Holder
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
L3
L2
L1
D4
Insert
Drill Dia.
x
D8
Insert Screw
Wrench
D1
Plate
Anti-seize
Lubricant
7.638
8.780 10.031 1.000 1/8-27
.9063
.9219
.9375
0061
7.953
9.134 11.508 1.250 1/4-18
.9531
.9688
0100
8.268
9.449 11.823 1.250 1/4-18
.9844
1.0000
1.0156
0102
8.583
9.764 12.138 1.250 1/4-18
1.0313
1.0469
0105
8.898 10.079 12.453 1.250 1/4-18
1.0781
1.0938
0107
9.213 10.394 12.768 1.250 1/4-18
1.1094
1.1250
0110
9.528 10.709 13.083 1.250 1/4-18
1.1563
1.1719
0112
9.843 11.220 13.594 1.250 1/4-18
TAWN0057T
TAWNH0057T
TAWN0058T
TAWNH0058T
TAWN0059T
TAWNH0059T
TAWN0060T
TAWNH0060T
TAWN0061T
TAWNH0061T
TAWN0062T
TAWNH0062T
TAWN0063T
TAWNH0063T
TAWN0100T
TAWNH0100T
TAWN0101T
TAWNH0101T
TAWN0102T
TAWNH0102T
TAWN0103T
TAWNH0103T
TAWN0104T
TAWNH0104T
TAWN0105T
TAWNH0105T
TAWN0106T
TAWNH0106T
TAWN0107T
TAWNH0107T
TAWN0108T
TAWNH0108T
TAWN0109T
TAWNH0109T
TAWN0110T
TAWNH0110T
TAWN0111T
TAWNH0111T
TAWN0112T
TAWNH0112T
(inch)
.8906
TAWLN0059
Stock
Order Number
1.1875
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
DRILLING
Stock
Order Number
VP15TF
Dimensions (inch)
Holder
a
a
a
INSERTS
L104
CUTTING CONDITIONS
L111
HOW TO USE
L111
TECHNICAL DATA
N001
L103

a Wavy
TAW

a Serration
INSERTS
y INCH STANDARD
Geometry
DRILLING
U Type
For easy installation
L104
Order Number
TAWN0040T
0041T
0042T
0043T
0044T
0045T
0046T
0047T
0048T
0049T
0050T
0051T
0052T
0053T
0054T
0055T
0056T
0057T
0058T
0059T
0060T
0061T
0062T
0063T
0100T
0101T
0102T
0103T
0104T
0105T
0106T
0107T
0108T
0109T
0110T
0111T
0112T
<One insert in one case>
Stock
VP15TF
Dimensions (inch)
Applicable Holder
D1
L2
S1
Inch
Metric
.6250
.6406
.311
.307
.236
.236
TAWS/M/LN0041
TAWS/M/LN1600S20
.6563
.303
.236
.6719
.299
.236
TAWS/M/LN0044
TAWS/M/LN1700S20
.6875
.299
.236
.7031
.295
.236
.7188
.291
.236
TAWS/M/LN0045
TAWS/M/LN0046
TAWS/M/LN1800S20
.7344
.366
.276
.7500
.362
.276
TAWS/M/LN0049
TAWS/M/LN1900S25
.7656
.362
.276
.7813
.358
.276
.7969
.354
.276
TAWS/M/LN0051
TAWS/M/LN2000S25
.8125
.350
.276
.8281
.346
.276
TAWS/M/LN0054
TAWS/M/LN2100S25
.8438
.346
.276
.8594
.406
.315
.8750
.402
.315
TAWS/M/LN0056
TAWS/M/LN2200S25
.8906
.398
.315
.9063
.394
.315
TAWS/M/LN0059
TAWS/M/LN2300S25
.9219
.394
.315
.9375
.390
.315
.9531
.386
.315
TAWS/M/LN0061
TAWS/M/LN2400S32
.9688
.437
.354
.9844
.433
.354
TAWS/M/LN0100
TAWS/M/LN2500S32
1.0000
.433
.354
1.0156
.429
.354
1.0313
.425
.354
TAWS/M/LN0102
TAWS/M/LN2600S32
1.0469
.421
.354
1.0625
.421
.354
TAWS/M/LN0105
TAWS/M/LN2700S32
1.0781
.417
.354
1.0938
.476
.394
1.1094
.472
.394
TAWS/M/LN0107
TAWS/M/LN2800S32
1.1250
.469
.394
1.1406
.469
.394
TAWS/M/LN0110
TAWS/M/LN2900S32
1.1563
.465
.394
1.1719
1.1875
.461
.457
.394
.394
TAWS/M/LN0112
TAWS/M/LN3000S32
Order Number
H Type
For stainless steel and
soft gummy materials
TAWNH0036T
0037T
0038T
0039T
0040T
0041T
0042T
0043T
0044T
0045T
0046T
0047T
0048T
0049T
0050T
0051T
0052T
0053T
0054T
0055T
0056T
0057T
0058T
0059T
0060T
0061T
0062T
0063T
0100T
0101T
0102T
0103T
0104T
0105T
0106T
0107T
0108T
0109T
0110T
0111T
0112T
Stock
VP15TF
Dimensions (inch)
Applicable Holder
D1
L2
S1
Inch
Metric
.5625
.5781
.299
.295
.197
.197
TAWS/M/LNH0036
TAWS/M/LNH0037
TAWS/M/LNH1400S16
a
a
.5938
.291
.197
.6094
.291
.197
.6250
.311
.236
.6406
.307
.236
.6563
.303
.236
.6719
.299
.236
.6875
.299
.236
.7031
.295
.236
.7188
.291
.236
.7344
.366
.276
.7500
.362
.276
.7656
.362
.276
.7813
.358
.276
.7969
.354
.276
.8125
.350
.276
.8281
.346
.276
.8438
.346
.276
.8594
.417
.315
.8750
.413
.315
.8906
.409
.315
.9063
.406
.315
.9219
.406
.315
.9375
.402
.315
.9531
.398
.315
.9688
.461
.354
.9844
.457
.354
1.0000
.457
.354
1.0156
.453
.354
1.0313
.449
.354
1.0469
.445
.354
1.0625
.445
.354
1.0781
.441
.354
1.0938
.484
.394
1.1094
.480
.394
1.1250
.476
.394
1.1406
.476
.394
1.1563
.472
.394
1.1719
1.1875
.469
.465
.394
.394
TAWS/M/LNH0039
TAWS/M/LNH1500S20
TAWS/M/LN0041
TAWS/M/LN1600S20
TAWS/M/LN0044
TAWS/M/LN1700S20
TAWS/M/LN0045
TAWS/M/LN0046
TAWS/M/LN1800S20
TAWS/M/LN0049
TAWS/M/LN1900S25
TAWS/M/LN0051
TAWS/M/LN2000S25
TAWS/M/LN0054
TAWS/M/LN2100S25
TAWS/M/LN0056
TAWS/M/LN2200S25
TAWS/M/LN0059
TAWS/M/LN2300S25
TAWS/M/LN0061
TAWS/M/LN2400S32
TAWS/M/LN0100
TAWS/M/LN2500S32
TAWS/M/LN0102
TAWS/M/LN2600S32
TAWS/M/LN0105
TAWS/M/LN2700S32
TAWS/M/LN0107
TAWS/M/LN2800S32
TAWS/M/LN0110
TAWS/M/LN2900S32
TAWS/M/LN0112
TAWS/M/LN3000S32
CUTTING CONDITIONS
L111
HOW TO USE
L111
TECHNICAL DATA
N001
DRILLING
Geometry
L105

a Wavy
TAW
Carbon Steel
Alloy Steel
Hardened
Steel

a Serration
Stainless
Steel
Cast Iron
Light Alloy
14 < D1< 18 18 <D1< 30 30<D1< 40
Heat Resistant
Alloy
D1 Tolerance
(mm)
0
0.018
0
0.021
0
0.025
METRIC STANDARD
L3
L2
L1
D4
TAWSNH1400S16
D1
Insert Screw
(l/d)
51
67
115
Drill Dia.
16
Wrench
Plate
WS254012T TKY08D WPT4405
Anti-seize
Lubricant
MK1KS
MNH1400S16
80
97
145
16
MK1KS
14.0
14.2
14.3
LNH1400S16
122
137
185
16
MK1KS
14.4
14.5
TAWSNH1500S20
54
75
125
20
MK1KS
14.6
14.7
14.8
14.9
MNH1500S20
85
105
155
20
MK1KS
15.0
15.1
DRILLING
15.2
LNH1500S20
130
148
198
20
MK1KS
15.3
15.4
TAWNH1400T
TAWKH1400TG
TAWNH1410T
TAWKH1410TG
TAWNH1420T
TAWKH1420TG
TAWNH1430T
TAWKH1430TG
TAWNH1440T
TAWKH1440TG
TAWNH1450T
TAWKH1450TG
TAWNH1460T
TAWKH1460TG
TAWNH1470T
TAWKH1470TG
TAWNH1480T
TAWKH1480TG
TAWNH1490T
TAWKH1490TG
TAWNH1500T
TAWKH1500TG
TAWNH1510T
TAWKH1510TG
TAWNH1520T
TAWKH1520TG
TAWNH1530T
TAWKH1530TG
TAWNH1540T
TAWKH1540TG
(mm)
14.1
5
Stock
Order Number
Clamp Torque (lbf-in) : WS254012T=18, WS254013T=18
L106
: Inventory maintained. s : Inventory maintained in Japan. d : Inventory maintained in Japan. (Available Spring 2011).
DP5010
Order Number
Insert
VP15TF
Dimensions (mm)
Holder
Stock
Hole depth
Internal Coolant
d
a
d
a
d
a
d
a
d
a
d
a
d
a
d
a
d
a
d
a
d
a
d
a
d
a
d
a
d
L1
D4
D1
Insert Screw
(l/d)
Wrench
Plate
Anti-seize
Lubricant
TAWSN1600S20
58
80
130
20
WS254014T TKY08D WPT4405 MK1KS
15.6
15.7
15.8
15.9
MN1600S20
91
115
165
20

16.0
16.1
16.2
LN1600S20
138
158
208
20
16.3
16.4
16.5
TAWSN1700S20
61
85
135
20
16.6
16.7
16.8
16.9
MN1700S20
96
120
170
20

17.0
17.1
17.2
LN1700S20
146
166
216
20
17.3
17.4
TAWN1550T
TAWNH1550T
TAWKH1550TG
TAWN1560T
TAWNH1560T
TAWKH1560TG
TAWN1570T
TAWNH1570T
TAWKH1570TG
TAWN1580T
TAWNH1580T
TAWKH1580TG
TAWN1590T
TAWNH1590T
TAWKH1590TG
TAWN1600T
TAWNH1600T
TAWKH1600TG
TAWN1610T
TAWNH1610T
TAWKH1610TG
TAWN1620T
TAWNH1620T
TAWKH1620TG
TAWN1630T
TAWNH1630T
TAWKH1630TG
TAWN1640T
TAWNH1640T
TAWKH1640TG
TAWN1650T
TAWNH1650T
TAWKH1650TG
TAWN1660T
TAWNH1660T
TAWKH1660TG
TAWN1670T
TAWNH1670T
TAWKH1670TG
TAWN1680T
TAWNH1680T
TAWKH1680TG
TAWN1690T
TAWNH1690T
TAWKH1690TG
TAWN1700T
TAWNH1700T
TAWKH1700TG
TAWN1710T
TAWNH1710T
TAWKH1710TG
TAWN1720T
TAWNH1720T
TAWKH1720TG
TAWN1730T
TAWNH1730T
TAWKH1730TG
TAWN1740T
TAWNH1740T
TAWKH1740TG
(mm)
15.5
Stock
Order Number
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
DRILLING
L2
Drill Dia.
DP5010
L3
Insert
VP15TF
Order Number
Stock
Hole depth
Dimensions (mm)
Holder
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
Clamp Torque (lbf-in) : WS254014T=18, WS254015T=18

CUTTING CONDITIONS
L111
HOW TO USE
L111
TECHNICAL DATA
N001
L107

a Wavy
TAW
Carbon Steel
Alloy Steel
Hardened
Steel

a Serration
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
14 < D1< 18 18 <D1< 30 30<D1< 40

D1 Tolerance
(mm)
0
0.018
0
0.021
0
0.025
METRIC STANDARD
L3
L2
L1
Drill Dia.
D4
D1
Insert Screw
(l/d)
Wrench
Plate
Anti-seize
Lubricant
TAWSN1800S20
65
90
140
20
MK1KS
17.6
17.7
17.8
17.9
MN1800S20
102
125
175
20
MK1KS
18.0
18.1
18.2
LN1800S20
DRILLING
154
174
224
20
MK1KS
18.3
18.4
TAWN1750T
TAWNH1750T
TAWKH1750TG
TAWN1760T
TAWNH1760T
TAWKH1760TG
TAWN1770T
TAWNH1770T
TAWKH1770TG
TAWN1780T
TAWNH1780T
TAWKH1780TG
TAWN1790T
TAWNH1790T
TAWKH1790TG
TAWN1800T
TAWNH1800T
TAWKH1800TG
TAWN1810T
TAWNH1810T
TAWKH1810TG
TAWN1820T
TAWNH1820T
TAWKH1820TG
TAWN1830T
TAWNH1830T
TAWKH1830TG
TAWN1840T
TAWNH1840T
TAWKH1840TG
(mm)
17.5
Stock
Order Number
Clamp Torque (lbf-in) : WS254016T=18
L108
DP5010
Order Number
Insert
VP15TF
Dimensions (mm)
Holder
Stock
Hole depth
Internal Coolant
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
L1
D4
D1
Insert Screw
(l/d)
Wrench
Plate
Anti-seize
Lubricant
TAWSN1900S25
68
99
155
25
WS304517T
TKY10T WPT4405
MK1KS
18.6
18.7
18.8
18.9
5
MN1900S25
107
134
190
25
WS304517T
TKY10T WPT4405
MK1KS
19.0
19.1
19.2
8
LN1900S25
162
185
241
25
WS304517T
TKY10T WPT4405
MK1KS
19.3
19.4
19.5
3
TAWSN2000S25
72
99
155
25
WS304518T
TKY10T WPT4405
MK1KS
19.6
19.7
5
MN2000S25
113
139
195
25
WS304518T
TKY10T WPT4405
MK1KS
19.8
19.9
8
LN2000S25
170
193
249
25
WS304518T
TKY10T WPT4405
MK1KS
20.0
TAWSN2100S25
75
99
155
25
WS304518T
TKY10T WPT4405
MK1KS
MN2100S25
118
139
195
25
WS304518T
TKY10T WPT4405
MK1KS
LN2100S25
178
202
258
25
WS304518T
TKY10T WPT4405
MK1KS
TAWSN2200S25
79.3 104.3 160.3
25
WS355520T
TKY15T WPT4405
MK1KS
MN2200S25
124.3 144.3 200.3
25
WS355520T
TKY15T WPT4405
MK1KS
LN2200S25
186
25
WS355520T
TKY15T WPT4405
MK1KS
210
266
TAWN1850T
TAWNH1850T
TAWKH1850TG
TAWN1860T
TAWNH1860T
TAWKH1860TG
TAWN1870T
TAWNH1870T
TAWKH1870TG
TAWN1880T
TAWNH1880T
TAWKH1880TG
TAWN1890T
TAWNH1890T
TAWKH1890TG
TAWN1900T
TAWNH1900T
TAWKH1900TG
TAWN1910T
TAWNH1910T
TAWKH1910TG
TAWN1920T
TAWNH1920T
TAWKH1920TG
TAWN1930T
TAWNH1930T
TAWKH1930TG
TAWN1940T
TAWNH1940T
TAWKH1940TG
TAWN1950T
TAWNH1950T
TAWKH1950TG
TAWN1960T
TAWNH1960T
TAWKH1960TG
TAWN1970T
TAWNH1970T
TAWKH1970TG
TAWN1980T
TAWNH1980T
TAWKH1980TG
TAWN1990T
TAWNH1990T
TAWKH1990TG
TAWN2000T
TAWNH2000T
TAWKH2000TG
TAWN2050T
TAWNH2050T
TAWKH2050TG
TAWN2100T
TAWNH2100T
TAWKH2100TG
TAWN2150T
TAWNH2150T
TAWKH2150TG
TAWN2200T
TAWNH2200T
TAWKH2200TG
(mm)
18.5
Stock
Order Number
20.5
21.0
21.5
22.0
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
DRILLING
L2
Drill Dia.
DP5010
L3
Insert
VP15TF
Order Number
Stock
Hole depth
Dimensions (mm)
Holder
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
Clamp Torque (lbf-in) : WS304517T=31, WS304518T=31, WS355520T=49

CUTTING CONDITIONS
L111
HOW TO USE
L111
TECHNICAL DATA
N001
L109

a Wavy
TAW
Carbon Steel
Alloy Steel
Hardened
Steel

a Serration
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
14 < D1< 18 18 <D1< 30 30<D1< 40

D1 Tolerance
(mm)
0
0.018
0
0.021
0
0.025
METRIC STANDARD
L3
L2
L1
D4
DRILLING
(l/d)
L110
Drill Dia.
D1
Insert Screw
Wrench
Plate
Anti-seize
Lubricant
TAWSN2300S25
82.3 104.3 160.3
25
WS355521T
TKY15T WPT4405
MK1KS
MN2300S25
129.3 154.3 210.3
25
WS355521T
TKY15T WPT4405
MK1KS
LN2300S25
194
25
WS355521T
TKY15T WPT4405
MK1KS
223
279
TAWSN2400S32
86.3 110.3 170.3
32
WS355521T
TKY15T WPT4405
MK1KS
MN2400S32
135.3 160.3 220.3
32
WS355521T
TKY15T WPT4405
MK1KS
LN2400S32
202
32
WS355521T
TKY15T WPT4405
MK1KS
232
292
TAWSN2500S32
88.6 110.6 170.6
32
WS406023T
TKY25T WPT4405
MK1KS
MN2500S32
140.6 165.6 225.6
32
WS406023T
TKY25T WPT4405
MK1KS
LN2500S32
210
32
WS406023T
TKY25T WPT4405
MK1KS
240
300
TAWSN2600S32
92.6 115.6 175.6
32
WS406024T
TKY25T WPT4405
MK1KS
MN2600S32
146.6 170.6 230.6
32
WS406024T
TKY25T WPT4405
MK1KS
LN2600S32
218
32
WS406024T
TKY25T WPT4405
MK1KS
248
308
TAWSN2700S32
94.6 115.6 175.6
32
WS406024T
TKY25T WPT4405
MK1KS
MN2700S32
151.6 175.6 235.6
32
WS406024T
TKY25T WPT4405
MK1KS
LN2700S32
226
32
WS406024T
TKY25T WPT4405
MK1KS
256
316
TAWSN2800S32
97.2 120.2 180.2
32
WS508026T
TKY27T WPT4405
MK1KS
MN2800S32
157.2 180.2 240.2
32
WS508026T
TKY27T WPT4405
MK1KS
LN2800S32
234
32
WS508026T
TKY27T WPT4405
MK1KS
264
324
TAWSN2900S32
100.2 125.2 185.2
32
WS508027T
TKY27T WPT4405
MK1KS
MN2900S32
162.2 185.2 245.2
32
WS508027T
TKY27T WPT4405
MK1KS
LN2900S32
242
32
WS508027T
TKY27T WPT4405
MK1KS
272
332
TAWSN3000S32
104.2 125.2 185.2
32
WS508027T
TKY27T WPT4405
MK1KS
MN3000S32
167.2 195.2 255.2
32
WS508027T
TKY27T WPT4405
MK1KS
LN3000S32
250
32
WS508027T
TKY27T WPT4405
MK1KS
285
345
Stock
Order Number
TAWN2250T
TAWNH2250T
TAWKH2250TG
TAWN2300T
TAWNH2300T
TAWKH2330TG
TAWN2350T
TAWNH2350T
TAWKH2350TG
TAWN2400T
TAWNH2400T
TAWKH2400TG
TAWN2450T
TAWNH2450T
TAWKH2450TG
TAWN2500T
TAWNH2500T
TAWKH2500TG
TAWN2550T
TAWNH2550T
TAWKH2550TG
TAWN2600T
TAWNH2600T
TAWKH2600TG
TAWN2650T
TAWNH2650T
TAWKH2650TG
TAWN2700T
TAWNH2700T
TAWKH2700TG
TAWN2750T
TAWNH2750T
TAWKH2750TG
TAWN2800T
TAWNH2800T
TAWKH2800TG
TAWN2850T
TAWNH2850T
TAWKH2850TG
TAWN2900T
TAWNH2900T
TAWKH2900TG
TAWN2950T
TAWNH2950T
TAWKH2950TG
TAWN3000T
TAWNH3000T
TAWKH3000TG
(mm)
22.5
23.0
23.5
24.0
24.5
25.0
25.5
26.0
26.5
27.0
27.5
28.0
28.5
29.0
29.5
30.0
Clamp Torque (lbf-in) : WS355521T=49, WS406023T=75, WS406024T=75, WS508026T=110, WS508027T=110

*(Note
) Please contact Mitsubishi Materials for special grades and geometries other than our standard products.
a
DP5010
Order Number
Insert
VP15TF
Dimensions (mm)
Holder
Stock
Hole depth
Internal Coolant
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d
a
a
d

Work Material
Mild Steel
Carbon Steel
Alloy Steel
M Stainless Steel
K
Mild Steel
Carbon Steel
Alloy Steel
M Stainless Steel
K

(SFM)
Hardness
Feed
(inch/rev)
&.6250" &.7188"
& 15.5 & 18.4mm
Cutting Speed
(SFM)
&.7344" &.8438"
& 18.5 & 21.4mm
Feed
(inch/rev)
Cutting Speed
(SFM)
Feed
(inch/rev)
< 180HB
230 (195 295)
.008 (.006 .010)
260 (195 330)
.010 (.008 .012)
295 (230 360)
.010 (.008 .012)
180 280HB
230 (195 295)
.008 (.006 .010)
260 (195 330)
.010 (.008 .012)
260 (195 330)
.010 (.008 .012)
280 350HB
195 (165 260)
.006 (.005 .007)
230 (165 295)
.008 (.006 .010)
230 (165 295)
.008 (.006 .010)
< 200HB
165 (130 195)
.006 (.005 .007)
165 (130 195)
.006 (.005 .007)
195 (165 230)
.008 (.006 .009)
230 (165 295)
.008 (.006 .010)
260 (195 295)
.010 (.008 .012)
295 (230 360)
.010 (.008 .012)
230 (165 295)
.008 (.006 .010)
260 (195 295)
.010 (.008 .012)
260 (195 295)
.010 (.008 .012)
Strength
< 350MPa
Strength
< 450MPa
Work Material
&.5625" &.6094"
& 14.0 & 15.4mm
Drill Diameter
D1
&.8594" &.9531"
& 21.5 & 24.4mm
Drill Diameter
D1

(SFM)
Hardness
Feed
(inch/rev)
&.9688" &1.0781"
& 24.5 & 27.4mm
Cutting Speed
(SFM)
& 1.0938" & 1.1875"

& 27.5 & 30.4mm
Feed
(inch/rev)
Cutting Speed
(SFM)
Feed
(inch/rev)
< 180HB
330 (260 390)
.012 (.010 .014)
360 (260 390)
.012 (.010 .014)
360 (260 390)
.012 (.010 .014)
180 280HB
295 (230 360)
.012 (.010 .014)
330 (260 390)
.012 (.010 .014)
330 (260 390)
.012 (.010 .014)
280 350HB
260 (195 330)
.010 (.008 .012)
295 (230 360)
.010 (.008 .012)
295 (230 360)
.010 (.008 .012)
< 200HB
195 (165 230)
.008 (.006 .009)
230 (195 260)
.010 (.008 .011)
230 (195 260)
.010 (.008 .011)
330 (260 360)
.014 (.010 .016)
360 (295 390)
.014 (.010 .016)
360 (295 390)
.016 (.012 .018)
295 (195 330)
.012 (.010 .014)
330 (260 360)
.012 (.010 .014)
330 (260 360)
.012 (.010 .014)
Strength
< 350MPa
Strength
< 450MPa
y NOTES ON USE
INSERT INSTALLATION
DRILLING
a Loosen insert screw of holder to install insert.

a Mesh the insert serration to holder grooves.
a Fasten the insert screw using the provided wrench while holding rake face of the insert lightly with your thumb. (Figure 1)
a Check that there is no clearance between the insert bottom and holder ute end. (Figure 2)
Slit
OK
NG
Clearance
Figure 1
Figure 2
NOTE ON INSERT REPLACEMENT

a Clean insert guide grooves by blowing air before installing a new insert.
a Clean the slit underneath the insert on the holder with the provided plate.
a Use the provided anti-seize lubricant for lubricating the threads of the insert screw.
TECHNICAL DATA
N001
L111
TAW
a Wavy

a Serration
INSERTS
y METRIC STANDARD
Order Number
H Type
soft and gummy materials
TAWNH1400T
1410T
1420T
1430T
1440T
1450T
1460T
1470T
1480T
1490T
1500T
1510T
1520T
1530T
1540T
1550T
1560T
1570T
1580T
1590T
1600T
1610T
1620T
1630T
1640T
1650T
1660T
1670T
1680T
1690T
1700T
1710T
1720T
1730T
1740T
1750T
1760T
1770T
1780T
1790T
1800T
1810T
1820T
1830T
1840T
DRILLING
Geometry
L112
Dimensions (mm)
Stock
Applicable Holder
VP15TF
D1
L2
S1
a
a
14.0
14.1
7.6
7.6
5.0
5.0
14.2
7.6
5.0
14.3
7.6
5.0
14.4
7.6
5.0
14.5
7.5
5.0
14.6
7.5
5.0
14.7
7.5
5.0
14.8
7.5
5.0
14.9
7.5
5.0
15.0
7.4
5.0
15.1
7.4
5.0
15.2
7.4
5.0
15.3
15.4
7.4
7.4
5.0
5.0
15.5
15.6
7.9
7.9
6.0
6.0
15.7
7.9
6.0
15.8
7.9
6.0
15.9
7.9
6.0
16.0
7.8
6.0
16.1
7.8
6.0
16.2
7.8
6.0
16.3
16.4
7.8
7.8
6.0
6.0
16.5
16.6
7.7
7.7
6.0
6.0
16.7
7.7
6.0
16.8
7.7
6.0
16.9
7.7
6.0
17.0
7.6
6.0
17.1
7.6
6.0
17.2
7.6
6.0
17.3
17.4
7.6
7.6
6.0
6.0
17.5
17.6
7.5
7.5
6.0
6.0
17.7
7.5
6.0
17.8
7.5
6.0
17.9
7.5
6.0
18.0
7.4
6.0
18.1
7.4
6.0
18.2
7.4
6.0
18.3
18.4
7.4
7.4
6.0
6.0
a
a
a
a
a
a
Inch
Metric
TAWSNH0036
TAWMNH0036
TAWLNH0036
TAWSNH1400S16
TAWMNH1400S16
TAWLNH1400S16
TAWSNH0037
TAWMNH0037
TAWLNH0037
TAWSNH0039
TAWMNH0039
TAWLNH0039
TAWSNH1500S20
TAWMNH1500S20
TAWLNH1500S20
TAWSN0041
TAWMN0041
TAWLN0041
TAWSN1600S20
TAWMN1600S20
TAWLN1600S20
TAWSN0044
TAWMN0044
TAWLN0044
TAWSN1700S20
TAWMN1700S20
TAWLN1700S20
TAWSN0045
TAWMN0045
TAWLN0045
TAWSN0046
TAWMN0046
TAWLN0046
TAWSN1800S20
TAWMN1800S20
TAWLN1800S20
Order Number
H Type
soft and gummy materials
TAWNH1850T
1860T
1870T
1880T
1890T
1900T
1910T
1920T
1930T
1940T
1950T
1960T
1970T
1980T
1990T
2000T
2050T
2100T
2150T
2200T
2250T
2300T
2350T
2400T
2450T
2500T
2550T
2600T
2650T
2700T
2750T
2800T
2850T
2900T
2950T
3000T
Dimensions (mm)
Stock
Applicable Holder
VP15TF
D1
L2
S1
a
a
18.5
18.6
9.3
9.3
7.0
7.0
18.7
9.3
7.0
18.8
9.3
7.0
18.9
9.3
7.0
19.0
9.2
7.0
19.1
9.2
7.0
19.2
9.2
7.0
19.3
19.4
9.2
9.2
7.0
7.0
19.5
19.6
9.1
9.1
7.0
7.0
19.7
9.1
7.0
19.8
9.1
7.0
19.9
20.0
9.1
9.0
7.0
7.0
20.5
21.0
8.9
8.8
7.0
7.0
21.5
22.0
10.6
10.5
8.0
8.0
22.5
23.0
10.4
10.3
8.0
8.0
23.5
24.0
10.2
10.1
8.0
9.0
24.5
25.0
11.7
11.6
9.0
9.0
25.5
26.0
11.5
11.4
9.0
9.0
26.5
27.0
11.3
11.2
9.0
9.0
27.5
28.0
12.3
12.2
10.0
10.0
28.5
29.0
12.1
12.0
10.0
10.0
29.5
30.0
11.9
11.8
10.0
10.0
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Inch
Metric
TAWSN0049
TAWMN0049
TAWLN0049
TAWSN1900S25
TAWMN1900S25
TAWLN1900S25
TAWSN0051
TAWMN0051
TAWLN0051
TAWSN2000S25
TAWMN2000S25
TAWLN2000S25
TAWSN0054
TAWMN0054
TAWLN0054
TAWSN0056
TAWMN0056
TAWLN0056
TAWSN0059
TAWMN0059
TAWLN0059
TAWSN0061
TAWMN0061
TAWLN0061
TAWSN0100
TAWMN0100
TAWLN0100
TAWSN0102
TAWMN0102
TAWLN0102
TAWSN0105
TAWMN0105
TAWLN0105
TAWSN0107
TAWMN0107
TAWLN0107
TAWSN0110
TAWMN0110
TAWLN0110
TAWSN0112
TAWMN0112
TAWLN0112
TAWSN2100S25
TAWMN2100S25
TAWLN2100S25
TAWSN2200S25
TAWMN2200S25
TAWLN2200S25
TAWSN2300S25
TAWMN2300S25
TAWLN2300S25
TAWSN2400S32
TAWMN2400S32
TAWLN2400S32
TAWSN2500S32
TAWMN2500S32
TAWLN2500S32
TAWSN2600S32
TAWMN2600S32
TAWLN2600S32
TAWSN2700S32
TAWMN2700S32
TAWLN2700S32
TAWSN2800S32
TAWMN2800S32
TAWLN2800S32
TAWSN2900S32
TAWMN2900S32
TAWLN2900S32
TAWSN3000S32
TAWMN3000S32
TAWLN3000S32
CUTTING CONDITIONS
L111
HOW TO USE
L111
TECHNICAL DATA
N001
DRILLING
Geometry
L113
TAW
a Wavy

a Serration
INSERTS
y METRIC STANDARD
Geometry
DRILLING
H Type
For Cast iron
L114
Order Number
TAWKH1400TG
1410TG
1420TG
1430TG
1440TG
1450TG
1460TG
1470TG
1480TG
1490TG
1500TG
1510TG
1520TG
1530TG
1540TG
1550TG
1560TG
1570TG
1580TG
1590TG
1600TG
1610TG
1620TG
1630TG
1640TG
1650TG
1660TG
1670TG
1680TG
1690TG
1700TG
1710TG
1720TG
1730TG
1740TG
1750TG
1760TG
1770TG
1780TG
1790TG
1800TG
1810TG
1820TG
1830TG
1840TG
Dimensions (mm)
Stock
Applicable Holder
DP5010
D1
L2
S1
d
d
14.0
14.1
7.6
7.6
5.0
5.0
14.2
7.6
5.0
14.3
7.6
5.0
14.4
7.6
5.0
14.5
7.5
5.0
14.6
7.5
5.0
14.7
7.5
5.0
14.8
7.5
5.0
14.9
7.5
5.0
15.0
7.4
5.0
15.1
7.4
5.0
15.2
7.4
5.0
15.3
15.4
7.4
7.4
5.0
5.0
15.5
15.6
7.9
7.9
6.0
6.0
15.7
7.9
6.0
15.8
7.9
6.0
15.9
7.9
6.0
16.0
7.8
6.0
16.1
7.8
6.0
16.2
7.8
6.0
16.3
16.4
7.8
7.8
6.0
6.0
16.5
16.6
7.7
7.7
6.0
6.0
16.7
7.7
6.0
16.8
7.7
6.0
16.9
7.7
6.0
17.0
7.6
6.0
17.1
7.6
6.0
17.2
7.6
6.0
17.3
17.4
7.6
7.6
6.0
6.0
17.5
17.6
7.5
7.5
6.0
6.0
17.7
7.5
6.0
17.8
7.5
6.0
17.9
7.5
6.0
18.0
7.4
6.0
18.1
7.4
6.0
18.2
7.4
6.0
18.3
18.4
7.4
7.4
6.0
6.0
d
d
d
d
d
d
: Inventory maintained in Japan. (Available Spring 2011).
Inch
Metric
TAWSNH0036
TAWMNH0036
TAWLNH0036
TAWSNH1400S16
TAWMNH1400S16
TAWLNH1400S16
TAWSNH0037
TAWMNH0037
TAWLNH0037
TAWSNH0039
TAWMNH0039
TAWLNH0039
TAWSNH1500S20
TAWMNH1500S20
TAWLNH1500S20
TAWSN0041
TAWMN0041
TAWLN0041
TAWSN1600S20
TAWMN1600S20
TAWLN1600S20
TAWSN0044
TAWMN0044
TAWLN0044
TAWSN1700S20
TAWMN1700S20
TAWLN1700S20
TAWSN0045
TAWMN0045
TAWLN0045
TAWSN0046
TAWMN0046
TAWLN0046
TAWSN1800S20
TAWMN1800S20
TAWLN1800S20
H Type
For Cast iron
Order Number
TAWKH1850TG
1860TG
1870TG
1880TG
1890TG
1900TG
1910TG
1920TG
1930TG
1940TG
1950TG
1960TG
1970TG
1980TG
1990TG
2000TG
2050TG
2100TG
2150TG
2200TG
2250TG
2300TG
2350TG
2400TG
2450TG
2500TG
2550TG
2600TG
2650TG
2700TG
2750TG
2800TG
2850TG
2900TG
2950TG
3000TG
Dimensions (mm)
Stock
Applicable Holder
DP5010
D1
L2
S1
d
d
18.5
18.6
9.3
9.3
7.0
7.0
18.7
9.3
7.0
18.8
9.3
7.0
18.9
9.3
7.0
19.0
9.2
7.0
19.1
9.2
7.0
19.2
9.2
7.0
19.3
19.4
9.2
9.2
7.0
7.0
19.5
19.6
9.1
9.1
7.0
7.0
19.7
9.1
7.0
19.8
9.1
7.0
19.9
20.0
9.1
9.0
7.0
7.0
20.5
21.0
8.9
8.8
7.0
7.0
21.5
22.0
10.6
10.5
8.0
8.0
22.5
23.0
10.4
10.3
8.0
8.0
23.5
24.0
10.2
10.1
8.0
9.0
24.5
25.0
11.7
11.6
9.0
9.0
25.5
26.0
11.5
11.4
9.0
9.0
26.5
27.0
11.3
11.2
9.0
9.0
27.5
28.0
12.3
12.2
10.0
10.0
28.5
29.0
12.1
12.0
10.0
10.0
29.5
30.0
11.9
11.8
10.0
10.0
d
d
d
d
d
d
d
d
d
d
d
d
d
d
d
d
d
d
d
d
d
d
d
Inch
Metric
TAWSN0049
TAWMN0049
TAWLN0049
TAWSN1900S25
TAWMN1900S25
TAWLN1900S25
TAWSN0051
TAWMN0051
TAWLN0051
TAWSN2000S25
TAWMN2000S25
TAWLN2000S25
TAWSN0054
TAWMN0054
TAWLN0054
TAWSN0056
TAWMN0056
TAWLN0056
TAWSN0059
TAWMN0059
TAWLN0059
TAWSN0061
TAWMN0061
TAWLN0061
TAWSN0100
TAWMN0100
TAWLN0100
TAWSN0102
TAWMN0102
TAWLN0102
TAWSN0105
TAWMN0105
TAWLN0105
TAWSN0107
TAWMN0107
TAWLN0107
TAWSN0110
TAWMN0110
TAWLN0110
TAWSN0112
TAWMN0112
TAWLN0112
TAWSN2100S25
TAWMN2100S25
TAWLN2100S25
TAWSN2200S25
TAWMN2200S25
TAWLN2200S25
TAWSN2300S25
TAWMN2300S25
TAWLN2300S25
TAWSN2400S32
TAWMN2400S32
TAWLN2400S32
TAWSN2500S32
TAWMN2500S32
TAWLN2500S32
TAWSN2600S32
TAWMN2600S32
TAWLN2600S32
TAWSN2700S32
TAWMN2700S32
TAWLN2700S32
TAWSN2800S32
TAWMN2800S32
TAWLN2800S32
TAWSN2900S32
TAWMN2900S32
TAWLN2900S32
TAWSN3000S32
TAWMN3000S32
TAWLN3000S32
CUTTING CONDITIONS
L111
HOW TO USE
L111
TECHNICAL DATA
N001
DRILLING
Geometry
L115
TAW
a Wavy

a Serration
INSERTS
y METRIC STANDARD
Geometry
DRILLING
U Type
L116
Order Number
TAWN1550T
1560T
1570T
1580T
1590T
1600T
1610T
1620T
1630T
1640T
1650T
1660T
1670T
1680T
1690T
1700T
1710T
1720T
1730T
1740T
1750T
1760T
1770T
1780T
1790T
1800T
1810T
1820T
1830T
1840T
1850T
1860T
1870T
1880T
1890T
1900T
1910T
1920T
1930T
1940T
1950T
1960T
1970T
1980T
1990T
2000T
Dimensions (mm)
Stock
Applicable Holder
VP15TF
D1
L2
S1
a
a
15.5
15.6
7.9
7.9
6.0
6.0
15.7
7.9
6.0
15.8
7.9
6.0
15.9
7.9
6.0
16.0
7.8
6.0
16.1
7.8
6.0
16.2
7.8
6.0
16.3
16.4
7.8
7.8
6.0
6.0
16.5
16.6
7.7
7.7
6.0
6.0
16.7
7.7
6.0
16.8
7.7
6.0
16.9
7.7
6.0
17.0
7.6
6.0
17.1
7.6
6.0
17.2
7.6
6.0
17.3
17.4
7.6
7.6
6.0
6.0
17.5
17.6
7.5
7.5
6.0
6.0
17.7
7.5
6.0
17.8
7.5
6.0
17.9
7.5
6.0
18.0
7.4
6.0
18.1
7.4
6.0
18.2
7.4
6.0
18.3
18.4
7.4
7.4
6.0
6.0
18.5
18.6
9.3
9.3
7.0
7.0
18.7
9.3
7.0
18.8
9.3
7.0
18.9
9.3
7.0
19.0
9.2
7.0
19.1
9.2
7.0
19.2
9.2
7.0
19.3
19.4
9.2
9.2
7.0
7.0
19.5
19.6
9.1
9.1
7.0
7.0
19.7
9.1
7.0
19.8
9.1
7.0
19.9
20.0
9.1
9.0
7.0
7.0
a
a
a
a
a
a
a
a
Inch
Metric
TAWSN0041
TAWMN0041
TAWLN0041
TAWSN1600S20
TAWMN1600S20
TAWLN1600S20
TAWSN0044
TAWMN0044
TAWLN0044
TAWSN1700S20
TAWMN1700S20
TAWLN1700S20
TAWSN0045
TAWMN0045
TAWLN0045
TAWSN0046
TAWMN0046
TAWLN0046
TAWSN1800S20
TAWMN1800S20
TAWLN1800S20
TAWSN0049
TAWMN0049
TAWLN0049
TAWSN1900S25
TAWMN1900S25
TAWLN1900S25
TAWSN0051
TAWMN0051
TAWLN0051
TAWSN2000S25
TAWMN2000S25
TAWLN2000S25
U Type
Order Number
TAWN2050T
2100T
2150T
2200T
2250T
2300T
2350T
2400T
2450T
2500T
2550T
2600T
2650T
2700T
2750T
2800T
2850T
2900T
2950T
3000T
Dimensions (mm)
Stock
VP15TF
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
D1
L2
Applicable Holder
S1
Inch
Metric
TAWSN0054
TAWMN0054
TAWLN0054
TAWSN0056
TAWMN0056
TAWLN0056
TAWSN0059
TAWMN0059
TAWLN0059
TAWSN0061
TAWMN0061
TAWLN0061
TAWSN0100
TAWMN0100
TAWLN0100
TAWSN0102
TAWMN0102
TAWLN0102
TAWSN0105
TAWMN0105
TAWLN0105
TAWSN0107
TAWMN0107
TAWLN0107
TAWSN0110
TAWMN0110
TAWLN0110
TAWSN0112
TAWMN0112
TAWLN0112
TAWSN2100S25
TAWMN2100S25
TAWLN2100S25
TAWSN2200S25
TAWMN2200S25
TAWLN2200S25
TAWSN2300S25
TAWMN2300S25
TAWLN2300S25
TAWSN2400S32
TAWMN2400S32
TAWLN2400S32
TAWSN2500S32
TAWMN2500S32
TAWLN2500S32
TAWSN2600S32
TAWMN2600S32
TAWLN2600S32
TAWSN2700S32
TAWMN2700S32
TAWLN2700S32
TAWSN2800S32
TAWMN2800S32
TAWLN2800S32
TAWSN2900S32
TAWMN2900S32
TAWLN2900S32
TAWSN3000S32
TAWMN3000S32
TAWLN3000S32
20.5
21.0
8.9
8.8
7.0
7.0
21.5
22.0
10.3
10.2
8.0
8.0
22.5
23.0
10.1
10.0
8.0
8.0
23.5
24.0
9.9
9.8
8.0
9.0
24.5
25.0
11.1
11.0
9.0
9.0
25.5
26.0
10.9
10.8
9.0
9.0
26.5
27.0
10.7
10.6
9.0
9.0
27.5
28.0
12.1
12.0
10.0
10.0
28.5
29.0
11.9
11.8
10.0
10.0
29.5
30.0
11.7
11.6
10.0
10.0
DRILLING
Geometry
CUTTING CONDITIONS
L111
HOW TO USE
L111
TECHNICAL DATA
N001
L117
DRILLING(INDEXABLE TYPE)
CHAMFER RING
D7
a Drilling and chamfering can be done at the same time.

a Chamfering position can be changed according to the machining depth.
a Maximum chamfer width: 4mm
45
H1
45
L3
Tool Holder
Number
Stock
TAW200R-90
210R-90
220R-90
230R-90
240R-90
250R-90
260R-90
270R-90
280R-90
290R-90
300R-90
Dimensions (mm)
Maximum
chamfer
width
L1
D7
H1
40
40
53
54
44
46
4
4
40
55
46
40
56
48
40
57
48
42
58
50
42
59
50
42
60
52
42
61
52
45
45
62
63
54
54
L1
Drilled Depth L3 (min.max.)
Suitable TAW Type Drill
TAWS
TAWM
12 29
12 32
14 36
29 70
32 75
36 81
70 127
75 135
81 143
TAWL
TAWS/M/L2000S25
TAWS/M/L2100S25
14 39
14 43
39 86
43 92
86 151
92 159
TAWS/M/L2300S25
15 43
15 47
43 95
47 101
95 165
101 173
49 106
52 112
106 181
112 189
TAWS/M/L2700S32
15 49
15 52
4
4
15 52
15 56
52 114
56 119
114 194
119 202
TAWS/M/L2900S32
TAWS/M/L3000S32
TAWS/M/L2200S25
TAWS/M/L2400S32
TAWS/M/L2500S32
TAWS/M/L2600S32
TAWS/M/L2800S32
DRILLING
(Note) For cutting conditions, refer to the recommended cutting conditions for the TAW drill on page L111.
If tears or vibrations occur, reduce the feed or cutting speed.
SPARE PARTS
z
TAW200R-90
210R-90
220R-90
230R-90
240R-90
250R-90
260R-90
270R-90
280R-90
290R-90
300R-90
Insert
Clamp Screw
(Insert)
Guide Plate
Screw
(Guide Plate)
TS254
TS254
TAWP20-21
TAWP20-21
HSC04008
HSC04008
TSR06011S
TSR06011S
TSR05008S
TSR05008S
TS254
TAWP22-24
HSC04008
TSR06011S
TSR05008S
TS254
TAWP22-24
HSC04008
TSR06011S
TSR05008S
TS254
TAWP22-24
HSC04008
TSR06011S
TSR05008S
zTKY20R
TS254
TAWP25-26
HSC04008
TSR06011S
TSR05008S
zTKY10R
TS254
TAWP25-26
HSC04008
TSR06011S
TSR05008S
xTKY08F
TS254
TAWP27-28
HSC04008
TSR06011S
TSR05008S
TS254
TAWP27-28
HSC04008
TSR06011S
TSR05008S
TS254
TS254
TAWP29-30
TAWP29-30
HSC04008
HSC04008
TSR06011S
TSR06011S
TSR05008S
TSR05008S
(Note) The above parts are provided with the chamfer ring except insert.
L118
Tool Holder
Number
Run-out adjust
Set screw
(Chamfer Ring)
Screw
Wrench
TAWC12T301-45GM
INSERTS
Stock
Shape
Geometry (mm)
Order Number
VP15TF
s
R 0.1
6.5
TAWC12T301-45GM
11
45
8.
3.97
5
11
y CHAMFER RING INSTALLATION

1. Loosen the set screws (A) and run-out adjusting screws (B) on the chamfer ring.
2. Install the guide plates into the pockets provided and tighten the guide plate mounting screws.
3. Remove the TAW drill insert and, if necessary, the insert clamp screw.
4. Install the chamfer ring from the insert end of the drill oriented as shown in g. 1.
Note: Prior to locking the ring in its axial position rotate the ring so the Guide Plates contact the drill utes on the side of the
ute as indicated in g. 1.
5. Position the chamfer ring at the proper axial position and secure with the 2 set screws (A).
Tighten the set screws to 53 lbf-in.
6. Tighten the run-out adjust screws (B) until the chamfering insert contacts the TAW drill body as shown in g. 2.
Note: Stop tightening the run-out adjusting screw when chamfering insert contacts the TAW drill body.
If the run-out adjusting screws are over tightened the chamfering insert may be damaged.
Maximum torque for the run-out adjusting screw is 18 lbf-in.
Fig. 1
Chamfer Ring
Clamp Screw
Set Screw (A)

(Clamp Torque (Guide) : 53 lbf-in)
Guide Plate
Chamfering Insert
<Double Sided Relief>
Fig. 2
DRILLING
TAW Drill Insert
The guide plate and drill ute should make

contact in this area.
Run-out Adjust Screw (B) <Double Sided Relief>
(Clamp Torque (Guide) : 18 lbf-in)
Make the chamfering insert contact with the TAW drill.
(When detaching or moving the chamfer ring,
ensure there is a clearance between the inserts and the body.)
TECHNICAL DATA
N001
L119
a Highly
rigid drill body.

corner insert.
a Various grades and chip breakers.
TAFM
Carbon Steel
Alloy Steel
Hardened
Steel
a4
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
INCH STANDARD
L/D=3
Drills 1.938" and above have 4 inserts.

D8(NPT)
Dimensions (inch)
D1
L3
L2
L1
D4
D7
D8
No. of
Inserts
.468
1.60
2.47
4.22
.750
1.02
1/8
.500
1.70
2.56
4.31
.750
1.02
1/8
040204-Uo
TS2
zTKY06F
0531
.531
1.79
2.66
4.41
.750
1.02
1/8
040204-Uo
TS2
zTKY06F
0562
.562
1.89
2.75
4.50
.750
1.02
1/8
040204-Uo
TS2
zTKY06F
0593
.593
1.98
2.84
4.59
.750
1.02
1/8
GPMT 060204-Uo
TS2
zTKY06F
0625
.625
2.13
3.31
6.31
1.000
1.73
1/4
060204-Uo
TS2
zTKY06F
0687
.687
2.34
3.49
6.49
1.000
1.73
1/4
060204-Uo
TS2
zTKY06F
0750
.750
2.55
3.68
6.68
1.000
1.73
1/4
070204-Uo
TS25
zTKY08F
0812
.812
2.76
3.87
6.87
1.000
1.73
1/4
070204-Uo
TS25
zTKY08F
0875
.875
2.98
4.06
7.06
1.000
1.73
1/4
070204-Uo
TS25
zTKY08F
0937
.937
3.19
4.24
7.24
1.000
1.73
1/4
090304-Uo
TS3
zTKY08F
1000
1.000
3.40
4.43
7.43
1.250
1.89
1/4
090304-Uo
TS3
zTKY08F
1062
1.062
3.61
4.62
7.62
1.250
1.89
1/4
090304-Uo
TS3
zTKY08F
1125
1.125
3.83
4.77
7.77
1.250
1.89
1/4
11T308-Uo
TS4
xTKY15D
1187
1.187
4.04
5.14
8.14
1.500
2.09
1/4
11T308-Uo
TS4
xTKY15D
1250
1.250
4.25
5.33
8.33
1.500
2.09
1/4
11T308-Uo
TS4
xTKY15D
1312
1.312
4.46
5.52
8.52
1.500
2.09
1/4
11T308-Uo
TS4
xTKY15D
1375
1.375
4.68
5.71
8.71
1.500
2.28
1/4
140408-Uo
TS55
xTKY25D
1437
1.437
4.89
5.89
8.89
1.500
2.28
1/4
140408-Uo
TS55
xTKY25D
1500
1.500
5.10
6.08
9.08
1.500
2.28
1/4
140408-Uo
TS55
xTKY25D
1562
1.562
5.31
6.27
9.27
1.500
2.28
1/4
140408-Uo
TS55
xTKY25D
1625
1.625
5.53
6.46
9.46
1.500
2.28
1/4
140408-Uo
TS55
xTKY25D
Order Number
TAFM0468
0500
Insert No.
x
Insert Screw Wrench
TS2
zTKY06F
GCMT040204-Uo
1687
1.687
5.74
6.65
9.65
1.500
2.28
1/4
140408-Uo
TS55
xTKY25D
1750
1.750
5.95
6.83
9.83
1.500
2.28
1/4
140408-Uo
TS55
xTKY25D
1812
1.812
6.16
7.02
10.02
1.500
2.48
1/4
140408-Uo
TS55
xTKY25D
1875
1.875
6.37
7.21
10.21
1.500
2.48
1/4
140408-Uo
TS55
xTKY25D
1937
1.937
6.59
7.43
10.43
1.500
2.48
1/4
090304-Uo
TS3
zTKY08F
2000
2.000
6.80
7.61
10.61
1.500
2.48
1/4
090304-Uo
TS3
zTKY08F
2062
2.062
7.01
7.81
10.81
1.500
2.48
1/4
090304-Uo
TS3
zTKY08F
2125
2.125
7.22
7.99
10.99
1.500
2.48
1/4
090304-Uo
TS3
zTKY08F
2187
2.187
7.44
8.19
11.19
1.500
2.48
1/4
090304-Uo
TS3
zTKY08F
2250
2.250
7.65
8.39
11.39
1.500
2.48
1/4
11T308-Uo
TS4
xTKY15D
Clamp Torque (lbf-in) : TS2=5.3, TS25=8.9, TS3=8.9, TS4=31, TS55=66

L120
Stock
DRILLING
Internal Coolant
a Highly
rigid drill body.

corner insert.
TAFS
Carbon Steel
Alloy Steel
Hardened
Steel
a4
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
INCH STANDARD
L/D=2
1/4NPT
Internal Coolant
Stock
Dimensions (inch)
D1
L3
L2
L1
D4
D7
No. of
Inserts
.625
1.51
2.69
5.69
1.000
1.73
.750
1.80
2.93
5.93
1.000
1.73
Order Number
TAFS0625
0750
0875
.875
2.11
3.19
6.19
1.000
1.73
1000
1.000
2.40
3.43
6.43
1.250
1.89
1125
1.125
2.71
3.65
6.65
1.250
1.89
1250
1.250
3.00
4.08
7.08
1.500
2.09
Insert No.
x
Insert Screw Wrench
TS2
zTKY06F
GPMT 060204-Uo
070204-Uo
TS25
zTKY08F
070204-Uo
TS25
zTKY08F
090304-Uo
TS3
zTKY08F
11T308-Uo
TS4
xTKY15D
11T308-Uo
TS4
xTKY15D
DRILLING
* Clamp Torque (lbf-in) : TS2=5.3, TS25=8.9, TS3=8.9, TS4=31
INSERTS
L127
CUTTING CONDITIONS
L128
TECHNICAL DATA
N001
L121
a Highly
rigid drill body.

corner insert.
TAFL
Carbon Steel
Alloy Steel
Hardened
Steel
a4
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
1/4NPT
INCH STANDARD
L/D=4
Internal Coolant
Stock
Dimensions (inch)
D1
L3
L2
L1
D4
D7
No. of
Inserts
.625
2.76
3.94
6.94
1.000
1.73
.750
3.30
4.43
7.43
1.000
1.73
Order Number
TAFL0625
0750
0875
.875
3.86
4.94
7.94
1.000
1.73
1000
1.000
4.40
5.43
8.43
1.250
1.89
1125
1.125
4.96
5.90
8.90
1.250
1.89
1250
1.250
5.50
6.58
9.58
1.500
2.09
*
Insert No.
x
Insert Screw Wrench
TS2
zTKY06F
GPMT 060204-Uo
070204-Uo
TS25
zTKY08F
070204-Uo
TS25
zTKY08F
090304-Uo
TS3
zTKY08F
11T308-Uo
TS4
xTKY15D
11T308-Uo
TS4
xTKY15D
DRILLING

*(Note)
Please contact Mitsubishi Materials for special grades and geometries other than our standard products.
L122
a Highly
rigid drill body.

corner insert.
TAFS/TAFM/TAFL
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
a4
Heat Resistant
Alloy
METRIC STANDARD
Internal Coolant
12.0
2
3
12.5
2
3
13.0
2
3
13.5
2
3
14.0
2
3
14.5
2
3
15.0
2
3
15.5
2
3
16.0
2
3
4
16.5
2
3
17.0
2
3
4
17.5
2
3
18.0
2
3
4
18.5
2
3
19.0
2
3
4
Order Number
TAFS 1200F20
TAFM1200F20
TAFS 1250F20
TAFM1250F20
TAFS 1300F20
TAFM1300F20
TAFS 1350F20
TAFM1350F20
TAFS 1400F20
TAFM1400F20
TAFS 1450F20
TAFM1450F20
TAFS 1500F20
TAFM1500F20
TAFS 1550F20
TAFM1550F20
TAFS 1600F25
TAFM1600F25
TAFL 1600F25
TAFS 1650F25
TAFM1650F25
TAFS 1700F25
TAFM1700F25
TAFL 1700F25
TAFS 1750F25
TAFM1750F25
TAFS 1800F25
TAFM1800F25
TAFL 1800F25
TAFS 1850F25
TAFM1850F25
TAFS 1900F25
TAFM1900F25
TAFL 1900F25
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Dimensions (mm)
L3
L2
L1
D4
D7
D8
No. of
Insert
29
41
39
51
82
94
20
20
25
25
1/8
1/8
2
2
GCMT 040204-Uo
040204-Uo
29
41
39
51
82
94
20
20
25
25
1/8
1/8
2
2
040204-Uo
040204-Uo
31
44
41
54
84
97
20
20
25
25
1/8
1/8
2
2
31
44
41
54
84
97
20
20
25
25
1/8
1/8
33
47
43
57
86
100
20
20
25
25
1/8
1/8
Insert No.
Insert Screw
TS2
Wrench
TKY06F
TS2
TKY06F
TS2
TKY06F
TS2
TKY06F
040204-Uo
040204-Uo
TS2
TKY06F
TS2
TKY06F
2
2
040204-Uo
040204-Uo
TS2
TKY06F
TS2
TKY06F
2
2
040204-Uo
040204-Uo
TS2
TKY06F
TS2
TKY06F
TS2
TKY06F
33
47
43
57
86
100
20
20
25
25
1/8
1/8
2
2
040204-Uo
040204-Uo
TS2
TKY06F
35
50
45
60
88
103
20
20
25
25
1/8
1/8
2
2
GPMT 060204-Uo
060204-Uo
TS2
TKY06F
TS2
TKY06F
35
50
45
60
88
103
20
20
25
25
1/8
1/8
2
2
060204-Uo
060204-Uo
TS2
TKY06F
TS2
TKY06F
38
54
70
57
73
89
107
123
139
25
25
25
35
35
35
1/8
1/8
1/8
2
2
2
060204-Uo
060204-Uo
060204-Uo
TS2
TKY06F
TS2
TKY06F
TS2
TKY06F
38
54
57
73
107
123
25
25
35
35
1/8
1/8
2
2
060204-Uo
060204-Uo
TS2
TKY06F
TS2
TKY06F
41
58
75
59
76
93
109
126
143
25
25
25
35
35
35
1/8
1/8
1/8
2
2
2
060204-Uo
060204-Uo
060204-Uo
TS2
TKY06F
TS2
TKY06F
TS2
TKY06F
41
58
59
76
109
126
25
25
35
35
1/8
1/8
2
2
060204-Uo
060204-Uo
TS2
TKY06F
TS2
TKY06F
43
61
79
61
79
97
111
129
147
25
25
25
35
35
35
1/8
1/8
1/8
2
2
2
070204-Uo
TS25
TKY08F
070204-Uo
070204-Uo
TS25
TKY08F
TS25
TKY08F
43
61
61
79
111
129
25
25
35
35
1/8
1/8
2
2
070204-Uo
070204-Uo
TS25
TKY08F
TS25
TKY08F
46
65
84
63
82
101
113
132
151
25
25
25
35
35
35
1/8
1/8
1/8
2
2
2
070204-Uo
070204-Uo
070204-Uo
TS25
zTKY08F
TS25
zTKY08F
TS25
zTKY08F
DRILLING
Drill
Dia.
D1
(mm) (L/D)
Stock
Hole Depth
Side Coolant Not Available.

INSERTS
L127
CUTTING CONDITIONS
L128
TECHNICAL DATA
N001
L123
a Highly
rigid drill body.

corner insert.
TAFS/TAFM/TAFL
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
a4
Heat Resistant
Alloy
METRIC STANDARD
Internal Coolant
DRILLING
Drill
Dia.
D1
(mm) (L/D)
19.5
2
3
20.0
2
3
4
20.5
2
3
21.0
2
3
4
21.5
2
3
22.0
2
3
4
22.5
2
3
23.0
2
3
4
23.5
2
3
24.0
2
3
4
24.5
2
3
25.0
2
3
4
25.5
2
3
26.0
2
3
4
Order Number
TAFS 1950F25
TAFM1950F25
TAFS 2000F25
TAFM2000F25
TAFL 2000F25
TAFS 2050F25
TAFM2050F25
TAFS 2100F25
TAFM2100F25
TAFL 2100F25
TAFS 2150F25
TAFM2150F25
TAFS 2200F25
TAFM2200F25
TAFL 2200F25
TAFS 2250F25
TAFM2250F25
TAFS 2300F25
TAFM2300F25
TAFL 2300F25
TAFS 2350F25
TAFM2350F25
TAFS 2400F25
TAFM2400F25
TAFL 2400F25
TAFS 2450F25
TAFM2450F25
TAFS 2500F32
TAFM2500F32
TAFL 2500F32
TAFS 2550F32
TAFM2550F32
TAFS 2600F32
TAFM2600F32
TAFL 2600F32
Stock
Hole Depth
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Dimensions (mm)
L3
L2
L1
D4
D7
D8
46
65
63
82
113
132
25
25
35
35
1/8
1/8
2
2
070204-Uo
TS25
zTKY08F
48
68
88
65
85
105
115
135
155
25
25
25
35
35
35
1/8
1/8
1/8
2
2
2
070204-Uo
070204-Uo
070204-Uo
TS25
zTKY08F
TS25
zTKY08F
TS25
zTKY08F
48
68
65
85
115
135
25
25
35
35
1/8
1/8
2
2
070204-Uo
070204-Uo
TS25
zTKY08F
TS25
zTKY08F
50
71
92
67
88
109
117
138
159
25
25
25
35
35
35
1/8
1/8
1/8
2
2
2
070204-Uo
070204-Uo
070204-Uo
TS25
zTKY08F
TS25
zTKY08F
TS25
zTKY08F
50
71
67
88
117
138
25
25
35
35
1/8
1/8
2
2
070204-Uo
070204-Uo
TS25
zTKY08F
TS25
zTKY08F
53
75
97
69
91
113
119
141
163
25
25
25
35
35
35
1/8
1/8
1/8
2
2
2
070204-Uo
070204-Uo
070204-Uo
TS25
zTKY08F
TS25
zTKY08F
TS25
zTKY08F
53
75
69
91
119
141
25
25
35
35
1/8
1/8
2
2
070204-Uo
070204-Uo
TS25
zTKY08F
TS25
zTKY08F
55
78
101
71
94
117
121
144
167
25
25
25
35
35
35
1/8
1/8
1/8
2
2
2
090304-Uo
090304-Uo
090304-Uo
TS3
zTKY08F
TS3
zTKY08F
TS3
zTKY08F
55
78
71
94
121
144
25
25
35
35
1/8
1/8
2
2
090304-Uo
090304-Uo
TS3
zTKY08F
TS3
zTKY08F
58
82
106
73
97
121
123
147
171
25
25
25
35
35
35
1/8
1/8
1/8
2
2
2
090304-Uo
090304-Uo
090304-Uo
TS3
zTKY08F
TS3
zTKY08F
TS3
zTKY08F
58
82
73
97
123
147
25
25
35
35
1/8
1/8
2
2
090304-Uo
090304-Uo
TS3
zTKY08F
TS3
zTKY08F
60
85
110
75
100
125
130
155
180
32
32
32
42
42
42
1/8
1/8
1/8
2
2
2
090304-Uo
090304-Uo
090304-Uo
TS3
zTKY08F
TS3
zTKY08F
TS3
zTKY08F
TS3
zTKY08F
Insert No.
x
Insert Screw Wrench
TS25
zTKY08F
GPMT 070204-Uo
60
85
75
100
130
155
32
32
42
42
1/8
1/8
2
2
090304-Uo
090304-Uo
TS3
zTKY08F
62
88
114
77
103
129
132
158
184
32
32
32
42
42
42
1/8
1/8
1/8
2
2
2
090304-Uo
090304-Uo
090304-Uo
TS3
TS3
TS3
zTKY08F
zTKY08F
zTKY08F

*
L124
No. of
Insert
26.5
2
3
27.0
2
3
4
27.5
2
3
28.0
2
3
4
28.5
2
3
29.0
2
3
4
29.5
2
3
30.0
2
3
4
31.0
32.0
33.0
34.0
2
3
4
2
3
4
2
3
4
2
3
4
35.0
2
3
36.0
2
3
37.0
2
3
38.0
2
3
39.0
2
3
40.0
2
3
41.0
2
3
42.0
2
3
Order Number
TAFS 2650F32
TAFM2650F32
TAFS 2700F32
TAFM2700F32
TAFL 2700F32
TAFS 2750F32
TAFM2750F32
TAFS 2800F32
TAFM2800F32
TAFL 2800F32
TAFS 2850F32
TAFM2850F32
TAFS 2900F32
TAFM2900F32
TAFL 2900F32
TAFS 2950F32
TAFM2950F32
TAFS 3000F40
TAFM3000F40
TAFL 3000F40
TAFS 3100F40
TAFM3100F40
TAFL 3100F40
TAFS 3200F40
TAFM3200F40
TAFL 3200F40
TAFS 3300F40
TAFM3300F40
TAFL 3300F40
TAFS 3400F40
TAFM3400F40
TAFL 3400F40
TAFS 3500F40
TAFM3500F40
TAFS 3600F40
TAFM3600F40
TAFS 3700F40
TAFM3700F40
TAFS 3800F40
TAFM3800F40
TAFS 3900F40
TAFM3900F40
TAFS 4000F40
TAFM4000F40
TAFS 4100F40
TAFM4100F40
TAFS 4200F40
TAFM4200F40
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Dimensions (mm)
L3
L2
L1
D4
D7
D8
No. of
Insert
62
88
77
103
132
158
32
32
42
42
1/8
1/8
2
2
090304-Uo
TS3
zTKY08F
65
92
119
79
106
133
134
161
188
32
32
32
42
42
42
1/8
1/8
1/8
2
2
2
090304-Uo
090304-Uo
090304-Uo
TS3
zTKY08F
TS3
zTKY08F
TS3
zTKY08F
65
92
79
106
134
161
32
32
42
42
1/8
1/8
2
2
090304-Uo
090304-Uo
TS3
zTKY08F
TS3
zTKY08F
67
95
123
81
109
137
136
164
192
32
32
32
42
42
42
1/8
1/8
1/8
2
2
2
11T308-Uo
11T308-Uo
11T308-Uo
TS4
zTKY15D
TS4
zTKY15D
TS4
zTKY15D
67
95
81
109
136
164
32
32
42
42
1/8
1/8
2
2
11T308-Uo
11T308-Uo
TS4
TKY15D
TS4
TKY15D
70
99
128
83
112
141
138
167
196
32
32
32
42
42
42
1/8
1/8
1/8
2
2
2
11T308-Uo
11T308-Uo
11T308-Uo
TS4
TKY15D
TS4
TKY15D
TS4
TKY15D
70
99
83
112
138
167
32
32
42
42
1/8
1/8
2
2
11T308-Uo
11T308-Uo
TS4
TKY15D
TS4
TKY15D
72
102
132
90
120
150
155
185
215
40
40
40
50
50
50
1/4
1/4
1/4
2
2
2
11T308-Uo
11T308-Uo
11T308-Uo
TS4
TKY15D
TS4
TKY15D
TS4
TKY15D
74
105
136
92
123
154
157
188
219
40
40
40
50
50
50
1/4
1/4
1/4
2
2
2
11T308-Uo
11T308-Uo
11T308-Uo
TS4
TKY15D
TS4
TKY15D
TS4
TKY15D
77
109
141
94
126
158
159
191
223
40
40
40
50
50
50
1/4
1/4
1/4
2
2
2
11T308-Uo
11T308-Uo
11T308-Uo
TS4
TKY15D
TS4
TKY15D
TS4
TKY15D
79
112
145
96
129
162
161
194
227
40
40
40
50
50
50
1/4
1/4
1/4
2
2
2
11T308-Uo
11T308-Uo
11T308-Uo
TS4
TKY15D
TS4
TKY15D
TS4
TKY15D
82
116
150
98
132
166
163
197
231
40
40
40
50
50
50
1/4
1/4
1/4
2
2
2
11T308-Uo
11T308-Uo
11T308-Uo
TS4
TKY15D
TS4
TKY15D
TS4
TKY15D
84
119
100
135
165
200
40
40
50
50
1/4
1/4
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
86
122
102
138
167
203
40
40
50
50
1/4
1/4
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
89
126
104
141
169
206
40
40
50
50
1/4
1/4
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
91
129
106
144
171
209
40
40
50
50
1/4
1/4
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
94
133
108
147
173
212
40
40
50
50
1/4
1/4
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
96
136
110
150
175
215
40
40
50
50
1/4
1/4
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
98
139
112
153
177
218
40
40
50
50
1/4
1/4
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
2
2
140408-Uo
TS55
TKY25D
140408-Uo
TS55
TKY25D
101
143
114
156
179
221
40
40
50
50
1/4
1/4
Insert No.
x
Insert Screw Wrench
TS3
zTKY08F
GPMT 090304-Uo
DRILLING
Drill
Dia.
D1
(mm) (L/D)
Stock
Hole Depth
INSERTS
L127
CUTTING CONDITIONS
L128
TECHNICAL DATA
N001
L125
a Highly
rigid drill body.

corner insert.
TAFL
Carbon Steel
Alloy Steel
Hardened
Steel
a4
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
Drills 49.0mm and above have 4 inserts.
METRIC STANDARD
Internal Coolant
(PT)
DRILLING
Drill
Dia.
D1
(mm) (L/D)
43.0
2
3
44.0
2
3
45.0
2
3
46.0
2
3
47.0
2
3
48.0
2
3
49.0
2
3
50.0
2
3
51.0
2
3
52.0
2
3
53.0
2
3
54.0
2
3
55.0
2
3
56.0
2
3
Order Number
TAFS 4300F40
TAFM4300F40
TAFS 4400F40
TAFM4400F40
TAFS 4500F40
TAFM4500F40
TAFS 4600F40
TAFM4600F40
TAFS 4700F40
TAFM4700F40
TAFS 4800F40
TAFM4800F40
TAFS 4900F40
TAFM4900F40
TAFS 5000F40
TAFM5000F40
TAFS 5100F40
TAFM5100F40
TAFS 5200F40
TAFM5200F40
TAFS 5300F40
TAFM5300F40
TAFS 5400F40
TAFM5400F40
TAFS 5500F40
TAFM5500F40
TAFS 5600F40
TAFM5600F40
Stock
Hole Depth
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Dimensions (mm)
L3
L2
L1
D4
D7
D8
No. of
Insert
103
146
116
159
181
224
40
40
50
50
1/4
1/4
2
2
106
150
118
162
183
227
40
40
50
50
1/4
1/4
108
153
120
165
185
230
40
40
54
54
110
156
122
168
187
233
40
40
113
160
124
171
189
236
115
163
126
174
118
167
Insert No.
Insert Screw
TS55
GPMT 140408-Uo
140408-Uo
TS55
TKY25D
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
1/4
1/4
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
54
54
1/4
1/4
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
40
40
54
54
1/4
1/4
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
191
239
40
40
54
54
1/4
1/4
2
2
140408-Uo
140408-Uo
TS55
TKY25D
TS55
TKY25D
133
182
198
247
40
40
58
58
1/4
1/4
4
4
090304-Uo
090304-Uo
TS3
TKY08F
TS3
TKY08F
120
170
135
185
200
250
40
40
58
58
1/4
1/4
4
4
090304-Uo
090304-Uo
TS3
TKY08F
TS3
TKY08F
122
173
137
188
202
253
40
40
58
58
1/4
1/4
4
4
090304-Uo
090304-Uo
TS3
TKY08F
TS3
TKY08F
125
177
139
191
204
256
40
40
58
58
1/4
1/4
4
4
090304-Uo
090304-Uo
TS3
TKY08F
TS3
TKY08F
127
180
141
194
206
259
40
40
63
63
1/4
1/4
4
4
090304-Uo
090304-Uo
TS3
TKY08F
TS3
TKY08F
128
182
143
197
208
262
40
40
63
63
1/4
1/4
4
4
090304-Uo
090304-Uo
TS3
TKY08F
TS3
TKY08F
130
185
145
200
210
265
40
40
63
63
1/4
1/4
4
4
090304-Uo
090304-Uo
TS3
TKY08F
TS3
TKY08F
132
188
147
203
212
268
40
40
63
63
1/4
1/4
4
4
090304-Uo
090304-Uo
TS3
TS3
TKY08F
TKY08F
L126
x
Wrench
TKY25D
TAF TYPE DRILL

Shape
Class
INSERTS
U1 Breaker
GCMT
Drill Diameter
(inch)
(mm)
.469 .563inch
12.0 14.5mm
.594 .688inch
15.0 17.5mm
.750 .875inch
18.0 22.5mm
Order Number
Carbide
Coated
UE6020 GP20M UP20M US735 VP15TF TF15
GCMT040204-U1
Dimensions (inch)
D1
S1
Re
.196
.094
.016
GPMT060204-U1
.219
.094
.016
070204-U1
.250
.094
.016
090304-U1
.313
.125
.016
11T308-U1
.375
.156
.031
.500
.188
.031
GPMT
*1.9382.188inch
23.027.5mm
49.056.0mm
*
1.1251.313inch
2.250inch
28.034.0mm
1.3751.875inch
140408-U1
35.048.0mm
.469 .563inch
12.0 14.5mm GCMT040204-U2
.594 .688inch
15.0 17.5mm GPMT060204-U2
.750 .875inch
070204-U2
18.0 22.5mm
U2 Breaker
GCMT
GPMT
.196
.094
.016
.219
.094
.016
.250
.094
.016
.313
.125
.016
1.1251.313inch
2.250inch
28.034.0mm
11T308-U2
.375
.156
.031
.500
.188
.031
.219
.094
.016
.250
.094
.016
.9381.063inch
1.9382.188inch
23.027.5mm
49.056.0mm
090304-U2
.313
.125
.016
1.1251.313inch
2.250inch
28.034.0mm
11T308-U2
.375
.156
.031
.500
.188
.031
*
*
1.3751.875inch
140408-U2
35.048.0mm
.594 .688inch
15.0 17.5mm GPMT060204-U3
.750 .875inch
070204-U3
18.0 22.5mm
U3 Breaker
GPMT
090304-U2
*
*
1.3751.875inch
140408-U2
35.048.0mm
.594 .688inch
15.0 17.5mm GPGT 060204-U2
.750 .875inch
070204-U2
18.0 22.5mm
.9381.063inch
1.9382.188inch
23.027.5mm
49.056.0mm
U2 Breaker
GPGT
.219
.094
.016
.250
.094
.016
090304-U3
.313
.125
.016
1.1251.313inch
2.250inch
28.034.0mm
11T308-U3
.375
.156
.031
1.3751.875inch
35.048.0mm
140408-U3
.500
.188
.031
DRILLING
.9381.063inch
M
.9381.063inch
M
*1.9382.188inch
23.027.5mm
49.056.0mm
*
*
* : Drill has 4 inserts.

CUTTING CONDITIONS
L128
TECHNICAL DATA
N001
L127
TAF TYPE DRILL

INSERT RECOMMENDATION
y CHIP BREAKER RECOMMENDATION
Work Material P
Low Carbon Steel Medium Carbon Steel

Breaker
U1
U2
U3
Alloy Steel
Stainless Steel
N
Gray Cast Iron
Ductile Cast Iron Aluminum

Alloy
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
y INSERT GRADE RECOMMENDATION
Work Material P
Low Carbon Steel Medium Carbon Steel
Breaker
UP20M
GP20M
UE6020
US735
VP15TF
TF15
: 1st Recommendation u : 2nd Recommendation
M
Alloy Steel
: 1st Recommendation u : 2nd Recommendation
Stainless Steel
N
Gray Cast Iron
Ductile Cast Iron Aluminum

Alloy
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
GPGT
u
u
GPGT
u
u
e
e
Cutting Speed (SFM)

Work Material
Hardness
L/D = 2, L/D = 3
L/D = 4
&.469"&.594" &.625"&2.250" &.625"&1.250"

&12.0&14.5mm &15.0&56.0mm &18.0&340mm
Chip Breaker
RECOMMENDED CUTTING CONDITIONS (TAFp Series)

Feed (inch/rev)
Drill Diameter
.002
.0028
.003
.002
.003
.004
.003
(.0015 .005)
.003
(.002 .005)
.004
(.002 .006)
.004
(.002 .006)
.003
(.002 .004)
.004
(.002 .005)
.004
(.002 .005)
.0025
(.0015 .004)
.0025
(.0015 .005)
.003
(.0015 .005)
.0028
(.002 .004)
.006
(.004 .007)
.006
(.004 .007)
.0028
(.002 .004)
.004
(.003 .005)
.004
(.003 .005)
.008
(.006 .012)
.004
(.0015 .005)
.0045
(.003 .006)
.005
(.003 .007)
.005
(.003 .007)
.003
(.002 .005)
.004
(.003 .006)
.004
(.003 .006)
.003
(.0014 .004)
.004
(.0016 .006)
.004
(.0016 .006)
.004
(.0016 .005)
.007
(.004 .001)
.007
(.004 .001)
.004
(.0025 .005)
.006
(.003 .008)
.006
(.003 .008)
.009
(.006 .013)
U1 (.0015 .004) (.0015 .004) (.0015 .004)

Low Carbon
Steel
150 HB
500
656
500
(328 650) (500 1000) (328 650)
U2 (.0015 .004) (.0015 .005) (.0015 .005)

U3
.002
U1 (.0015 .004)
DRILLING
Medium Carbon
393
500
180 280 HB (
Steel
250 525) (375 600)
325
(262 400)
.002
U2 (.0015 .004)
U3
Alloy Steel
180 280 HB
393
500
(250 525) (375 600)
325
(262 400)
U1 (.0015 .004)
Stainless Steel
200 HB
325
500
(250 400) (375 650)
325
(262 400)
.002
U2 (.0015 .004)
U3
.0028
(.002 .004)
.0028
U2 (.0015 .004)
U1
Gray
Cast Iron
150 HB
400
500
(250 525) (375 600)
460
(360 525)
U3
Ductile
Cast Iron
L128

.002
.002
U1 (.0015 .004)
.002
U2 (.0015 .004)
U3
Aluminum
Alloy
140 HB
325
500
(250 500) (375 600)
325
(250 400)
D1
&.469"&.594" &.625"&.875" &.938"&1.313" &1.375"&1.813" &1.938"&2.250"

&12.0&14.5mm &15.0&22.5mm &23.0&34.0mm &35.0&48.0mm &49.0&56.0mm
.0028
U1 (.002 .004)
.002
U2 (.0015 .004)
U3
985
820
(655 1200) (490 1150) U2
.004
(.002 .005)
.005
(.002 .005)
.005
(.002 .005)
.005
(.003 .007)
.006
(.003 .008)
.006
(.003 .008)
.004
(.003 .005)
.005
(.003 .007)
.005
(.003 .007)
.004
(.0016 .005)
.004
(.0016 .006)
.004
(.0016 .006)
.004
(.0016 .005)
.007
(.004 .001)
.007
(.004 .001)
.004
(.0025 .005)
.007
(.003 .008)
.007
(.003 .008)
.010
(.006 .014)
.003
(.0015 .004)
.004
(.0015 .005)
.004
(.0015 .005)
.0045
(.003 .006)
.005
(.003 .007)
.005
(.003 .007)
.003
(.002 .005)
.004
(.003 .006)
.004
(.003 .006)
.003
(.0014 .004)
.004
(.0016 .006)
.004
(.0016 .006)
.004
(.0016 .005)
.007
(.004 .001)
.007
(.004 .001)
.004
(.0025 .005)
.006
(.003 .008)
.006
(.003 .008)
.009
(.006 .013)
CUTTING PERFORMANCE
y CUTTING RESISTANCE
Workpiece : AISI 4140 (200HB 220HB) Cutting Speed : 490 SFM
Cutting Power (HP)
Thrust (lb)
024
f = .0
IPR
Drill Diameter (inch)
IP
f=
02
06
PR
0
=.
40
00
.
f=
Thrust (lb)
004
f=.
IPR
04
.00
.0
f=
f=
PR
0I
Torque (lbf-in)
Cutting Power (HP)
.00
60
IP
R
R
Torque (lbf-in)
f=
24
IP
IP
IPR
.00
0
=.
Coolant Volume (GPM)
Coolant Pressure (PSI)
y COOLANT VOLUME AND PRESSURE
y CUTTING RESISTANCE
Workpiece : AISI 4140 (200HB 220HB) Cutting Speed : 490 SFM Drill Diameter : & 1.00
Torque (lbf-in)
Thrust (lb)
DRILLING
Cutting Power (HP)
B Comp
B Comp
B Comp
TAF Drill
Feed (IPR)
A Comp
Thrust (lb)
Torque (lbf-in)
Cutting Power (HP)
A Comp
A Comp
TAF Drill
Feed (IPR)
TAF Drill
Feed (IPR)
L129
DRILLING(BRAZED TYPE)
a Low
BRA
thrust due to absence of a chisel edge.

regrinding.
a Easy
NEW POINT DRILL
Carbon Steel
Alloy Steel
Hardened
Steel
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
.3125"< D1< .3906" .4063"< D1< .7031" .7188"< D1< 1.1719" 1.1875"< D1< 1.2500"
8< D1< 10mm 10<D1< 18mm 18<D1< 30mm
D1 Tolerance
(inch)
0
.00059
0
.00071
0
.00083
0
.00098
a General Use (Carbon Steel, Alloy Steel, Stainless Steel)
L/D=3
7
Internal Coolant
Helix Angle : 20
y INCH STANDARD
Dimensions (inch)
BRA0020
.3125
.859 1.375 3.250
.625 1/8
BRA0051
.7969 3.265 4.140 6.390 1.000 1/8
0021
.3281
.859 1.375 3.250
.625 1/8
0052
.8125 3.421 4.359 6.609 1.000 1/8
0022
.3438 1.049 1.578 3.906
.625 1/8
0053
.8281 3.421 4.359 6.609 1.000 1/8
0023
.3594 1.049 1.578 3.906
.625 1/8
0054
.8438 3.421 4.359 6.609 1.000 1/8
0024
.3750 1.312 1.765 3.640
.625 1/8
0055
.8594 3.578 4.546 6.769 1.000 1/8
0025
.3906 1.312 1.765 3.640
.625 1/8
0056
.8750 3.578 4.546 6.769 1.000 1/8
0026
.4063 1.312 1.765 3.640
.625 1/8
0057
.8906 3.734 4.765 7.015 1.000 1/8
0027
.4219 1.468 1.968 3.843
.625 1/8
0058
.9063 3.734 4.765 7.015 1.000 1/8
0028
.4375 1.468 1.968 3.843
.625 1/8
0059
.9219 3.734 4.765 7.015 1.000 1/8
0029
.4531 1.984 2.531 4.406
.625 1/8
0060
.9375 3.890 4.953 7.328 1.250 1/4
0030
.4688 1.984 2.531 4.406
.625 1/8
0061
.9531 3.890 4.953 7.328 1.250 1/4
0031
.4844 1.984 2.531 4.406
.625 1/8
0062
.9688 4.046 5.171 7.546 1.250 1/4
0032
.5000 2.140 2.734 4.609
.625 1/8
0063
.9844 4.046 5.171 7.546 1.250 1/4
0033
.5156 2.140 2.734 4.609
.625 1/8
0100
1.0000 4.046 5.171 7.546 1.250 1/4
0034
.5313 2.140 2.734 4.609
.625 1/8
0101
1.0156 4.046 5.359 7.734 1.250 1/4
0035
.5469 2.297 2.937 4.812
.625 1/8
0102
1.0313 4.203 5.359 7.734 1.250 1/4
0036
.5625 2.297 2.937 4.812
.625 1/8
0103
1.0469 4.359 5.578 7.953 1.250 1/4
0037
.5781 2.453 3.140 5.015
.625 1/8
0104
1.0625 4.359 5.578 7.953 1.250 1/4
0038
.5938 2.453 3.140 5.140
.750 1/8
0105
1.0781 4.359 5.578 7.953 1.250 1/4
0039
.6094 2.453 3.140 5.140
.750 1/8
0106
1.0938 4.515 5.765 8.140 1.250 1/4
0040
.6250 2.609 3.328 5.328
.750 1/8
0107
1.1094 4.515 5.765 8.140 1.250 1/4
0041
.6406 2.609 3.328 5.328
.750 1/8
0108
1.1250 4.671 5.984 8.359 1.250 1/4
0042
.6563 2.765 3.546 5.546
.750 1/8
0109
1.1406 4.671 5.984 8.359 1.250 1/4
0043
.6719 2.765 3.546 5.546
.750 1/8
0110
1.1563 4.671 5.984 8.359 1.250 1/4
0044
.6875 2.765 3.546 5.546
.750 1/8
0111
1.1719 4.828 6.172 8.546 1.250 1/4
0045
.7031 2.921 3.734 5.734
.750 1/8
0112
1.1875 4.828 6.172 8.546 1.250 1/4
0046
.7188 2.921 3.734 5.984 1.000 1/8
0113
1.2031 5.000 6.781 9.140 1.500 1/4
0047
.7344 3.109 3.953 6.203 1.000 1/8
0114
1.2188 5.000 6.781 9.140 1.500 1/4
0048
.7500 3.109 3.953 6.203 1.000 1/8
0115
1.2344 5.000 6.781 9.140 1.500 1/4
0049
.7656 3.109 3.953 6.203 1.000 1/8
0116
1.2500 5.172 6.609 9.359 1.500 1/4
0050
.7813 3.265 4.140 6.390 1.000 1/8
DRILLING
a
r
L3
L2
L1
D4
D8

Order Number
UP20M
D1
Order Number
L130
Dimensions (inch)
Stock
UP20M
Stock
D1
L3
L2
L1
D4
D8
y METRIC STANDARD
Dimensions (mm)
BRA0800S16
0850S16
0900S16
0950S16
1000S16
1050S16
1100S16
1150S16
1200S16
1250S16
1300S16
1350S16
1400S16
1450S16
1500S20
1550S20
1600S20
1650S20
1700S20
1750S20
1800S20
1850S20
1900S25
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Dimensions (mm)
Stock
D1
L3
L2
L1
D4
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
12.5
13.0
13.5
14.0
14.5
15.0
15.5
16.0
16.5
17.0
17.5
18.0
18.5
19.0
23
23
28
28
35
35
40
40
44
44
48
48
52
52
61
61
65
65
69
69
73
73
77
35
35
40
40
45
45
51
51
56
56
61
61
66
66
76
76
81
81
86
86
91
91
101
83
83
88
88
93
93
99
99
104
104
109
109
114
114
126
126
131
131
136
136
141
141
157
16
16
16
16
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
25
Order Number
BRA1950S25
2000S25
2050S25
2100S25
2150S25
2200S25
2250S25
2300S25
2350S25
2400S32
2450S32
2500S32
2550S32
2600S32
2650S32
2700S32
2750S32
2800S32
2850S32
2900S32
2950S32
3000S32
UP20M
Order Number
UP20M
Stock
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
D1
L3
L2
L1
D4
19.5
20.0
20.5
21.0
21.5
22.0
22.5
23.0
23.5
24.0
24.5
25.0
25.5
26.0
26.5
27.0
27.5
28.0
28.5
29.0
29.5
30.0
77
81
81
80
80
84
84
83
83
87
87
86
86
90
90
89
89
93
93
97
97
96
101
101
101
101
101
106
106
106
106
111
111
111
111
116
116
116
116
121
121
126
126
126
157
157
157
157
157
162
162
162
162
171
171
171
171
176
176
176
176
181
181
186
186
186
25
25
25
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
32
32
32
32

Hardness
Drill Dia.
&.3125" &.5156"
& 8.0 & 13.0mm
Feed
(inch/rev)
Cutting Speed
(SFM)
M
K
Drill Dia.
&.5313" &.7031"
& 13.5 & 18.0mm
Cutting Speed
(SFM)
Drill Dia.
Feed
(inch/rev)
>&.7031"
>& 18.5mm
Feed
(inch/rev)
Cutting Speed
(SFM)
< 180HB
180 (130 210) .010 (.008 .012) 210 (165 245) .012 (.010 .014) 245 (195 280) .012 (.010 .014)
Carbon Steel
Alloy Steel
180 280HB
165 (115 195) .010 (.008 .012) 195 (145 230) .012 (.010 .014) 230 (180 260) .012 (.010 .014)
280 350HB
130 (100 165) .010 (.008 .012) 165 (130 195) .010 (.008 .012) 180 (145 210) .011 (.008 .012)
Stainless Steel
< 200HB
Cast Iron
Tensile Strength
< 350MPa
Tensile Strength
< 450MPa
Mild Steel
Ductile Cast Iron

Titanium Alloy
100 (65 130) .010 (.008 .011)
115 (80 145) .011 (.008 .012) 130 (100 165) .012 (.010 .014)
195 (130 230) .012 (.010 .014) 230 (165 260) .014 (.012 .016) 260 (195 295) .016 (.014 .018)
180 (130 210) .011 (.008 .012) 195 (145 230) .012 (.010 .014) 230 (180 260) .012 (.010 .014)
50 (30 65)
.004 (.002 .005)
65 (30 80)
.006 (.004 .007)
65 (50 80)
.006 (.004 .008)
80 (65 100) .006 (.004 .008)
100 (65 115) .008 (.006 .010) 115 (100 130) .010 (.008 .012)
(Note) Above conditions are for general cutting.

The cutting conditions need to be modied depending on power, rigidity of the machine and workpiece shape.
y CUTTING FLUID
Water-soluble cutting uid containing large amount of E.P. additives.
DRILLING
Work Material
Fig. 2 Standard hone shape with T land BRA

Hone the entire
length of the cutting edge
y REGRINDING PROCEDURES
Contact your local Mitsubishi Carbide Representative or
Distributor for authorized regrinding facilities information.

Regrinding
Grind ank by moving table back and forth as shown in Fig. 1-(At the end of
grinding, be sure to spark out and maintain lip heights within .001 inch.)
Honing
Honing has great inuence on tool life and the accuracy of nished surface.
Be sure to hone the entire length (including radius) of cutting edge at each regrind.
For honing shape, refer to Fig. 2, Standard hone shape.
For honing use diamond le produced by Mitsubishi Materials Corp.
Fig. 1
Approx.
Relief angle
Work Material
Mild Steel
Carbon Steel
Alloy Steel
W (inch)
.006 .008
Work Material
W (inch)
Stainless steel
Titanium alloy
.002 .004
Cast iron
.001 .003
Diamond le (produced by Mitsubishi Materials Corp.)

Table traverse
Tilt the axis of the

grinding wheel 10 deg.
Roughing File
: T-1-140 (#140)
Finishing File
: T-0-400 (#400)
Ultra-Fine Finishing File : T-0-1500 (#1500)
Hold cutting edge parallel with table

surface and tilt it 15 deg. to the axis
of the grinding wheel.
TECHNICAL DATA
N001
L131
DRILLING(BRAZED TYPE)
a Excellent
cutting sharpness and chip discharge due to high rake type insert.
efciency, high accuracy machining.
a Suitable for stainless steel and mild steel cutting. Possible for general steel
cutting. (l/d=3)
BRS
Carbon Steel
Alloy Steel
Hardened
Steel
a High
Stainless
Steel
Cast Iron
Light Alloy
Heat Resistant
Alloy
.5000"< D1< .7031" .7188"< D1< 1.1719" D1=1.1875"

14<D1< 18mm 18<D1< 30mm
D1 Tolerance
(inch)
0
.00071
0
.00083
0
.00098
L/D=3
Internal Coolant
Helix Angle : 30
y INCH STANDARD
Dimensions (inch)
L3
L2
L1
D4
D8
Order Number
D1
L3
L2
L1
D4
D8
BRS0032
.5000 2.140 2.734 4.609
.625 1/8
BRS0055
.8594 3.578 4.546 6.796 1.000 1/8
0033
.5156 2.140 2.734 4.609
.625 1/8
0056
.8750 3.578 4.546 6.796 1.000 1/8
0034
.5313 2.140 2.734 4.609
.625 1/8
0057
.8906 3.734 4.765 7.015 1.000 1/8
0035
.5469 2.297 2.937 4.812
.625 1/8
0058
.9063 3.734 4.765 7.015 1.000 1/8
0036
.5625 2.297 2.937 4.812
.625 1/8
0059
.9219 3.734 4.765 7.015 1.000 1/8
0037
.5781 2.453 3.140 5.015
.625 1/8
0060
.9375 3.890 4.953 7.328 1.250 1/4
0038
.5938 2.453 3.140 5.140
.750 1/8
0061
.9531 3.890 4.953 7.328 1.250 1/4
0039
.6094 2.453 3.140 5.140
.750 1/8
0062
.9688 4.046 5.171 7.546 1.250 1/4
0040
.6250 2.609 3.328 5.328
.750 1/8
0063
.9844 4.046 5.171 7.546 1.250 1/4
0041
.6406 2.609 3.328 5.328
.750 1/8
0100
1.0000 4.046 5.171 7.546 1.250 1/4
0042
.6563 2.765 3.546 5.546
.750 1/8
0101
1.0156 4.203 5.359 7.734 1.250 1/4
0043
.6719 2.765 3.546 5.546
.750 1/8
0102
1.0313 4.203 5.359 7.734 1.250 1/4
0044
.6875 2.765 3.546 5.546
.750 1/8
0103
1.0469 4.359 5.578 7.953 1.250 1/4
0045
.7031 2.921 3.734 5.734
.750 1/8
0104
1.0625 4.359 5.578 7.953 1.250 1/4
0046
.7188 2.921 3.734 5.984 1.000 1/8
0105
1.0781 4.359 5.578 7.953 1.250 1/4
0047
.7344 3.109 3.953 6.203 1.000 1/8
0106
1.0938 4.515 5.765 8.140 1.250 1/4
0048
.7500 3.109 3.953 6.203 1.000 1/8
0107
1.1094 4.515 5.765 8.140 1.250 1/4
0049
.7656 3.109 3.953 6.203 1.000 1/8
0108
1.1250 4.671 5.984 8.359 1.250 1/4
0050
.7813 3.265 4.140 6.390 1.000 1/8
0109
1.1406 4.671 5.984 8.359 1.250 1/4
0051
.7969 3.265 4.140 6.390 1.000 1/8
0110
1.1563 4.671 5.984 8.359 1.250 1/4
0052
.8125 3.421 4.359 6.609 1.000 1/8
0111
1.1719 4.828 6.172 8.546 1.250 1/4
0053
.8281 3.421 4.359 6.609 1.000 1/8
0112
1.1875 4.828 6.172 8.546 1.250 1/4
0054
.8438 3.421 4.359 6.609 1.000 1/8
DRILLING
L132
D1
Dimensions (inch)
Stock
UP20M
Order Number
UP20M
Stock
y METRIC STANDARD
Dimensions (mm)
Dimensions (mm)
D1
UP20M
Stock
UP20M
Stock
D1
BRS1400S16
14.0
52
66
114
16
BRS2250S25
22.5
84
106
162
25
1450S16
14.5
52
66
114
16
2300S25
23.0
83
106
162
25
1500S20
15.0
61
76
126
20
2350S25
23.5
83
106
162
25
1550S20
15.5
61
76
126
20
2400S32
24.0
87
111
171
32
1600S20
16.0
65
81
131
20
2450S32
24.5
87
111
171
32
1650S20
16.5
65
81
131
20
2500S32
25.0
86
111
171
32
1700S20
17.0
69
86
136
20
2550S32
25.5
86
111
171
32
1750S20
17.5
69
86
136
20
2600S32
26.0
90
116
176
32
1800S20
18.0
73
91
141
20
2650S32
26.5
90
116
176
32
1850S20
18.5
73
91
141
20
2700S32
27.0
89
116
176
32
1900S25
19.0
77
101
157
25
2750S32
27.5
89
116
176
32
1950S25
19.5
77
101
157
25
2800S32
28.0
93
121
181
32
2000S25
20.0
81
101
157
25
2850S32
28.5
93
121
181
32
2050S25
20.5
81
101
157
25
2900S32
29.0
97
126
186
32
2100S25
21.0
80
101
157
25
2950S32
29.5
97
126
186
32
2150S25
21.5
80
101
157
25
3000S32
30.0
96
126
186
32
2200S25
22.0
84
106
162
25
Order Number
L3
L2
L1
D4
Order Number
L3
L2
L1
D4

&.5000" &.7813"
& 14.0 & 20.0mm
Cutting Speed
Feed
(SFM)
(inch/rev)
&.7969" & 1.1875"

& 20.5 & 30.0mm
Cutting Speed
Feed
(SFM)
(inch/rev)
< 180HB
210 (165 245)
.012 (.008 .016)
230 (180 280)
.014 (.008 .018)
180 280HB
195 (145 230)
.010 (.004 .014)
210 (145 260)
.012 (.006 .014)
280 350HB
180 (130 210)
.008 (.006 .014)
195 (145 230)
.010 (.006 .014)
< 200HB
230 (165 295)
.012 (.008 .016)
260 (195 330)
.012 (.008 .016)
Tensile Strength
< 350MPa
Tensile Strength
< 450MPa
Tensile Strength
500 800MPa
245 (195 360)
.012 (.008 .016)
260 (195 330)
.014 (.010 .020)
245 (195 330)
.012 (.008 .016)
260 (195 330)
.014 (.008 .018)
230 (180 295)
.010 (.006 .014)
245 (180 295)
.012 (.006 .016)
Work Material
Mild Steel
Carbon Steel
Alloy Steel
M
K
Stainless Steel (Austenitic)

Gray Cast Iron
Ductile Cast Iron
Hardness
Drill Dia.
DRILLING
Drill Dia.
(Note) Above conditions are for general cutting.

The cutting conditions need to be modied depending on power, rigidity of the machine and workpiece shape.
TECHNICAL DATA
N001
L133
Memo
L134
SPARE PARTS
IDENTIFICATION ................................ M002
SPARE PARTS
CLAMP SCREW .............................. M003
SET BOLT ....................................... M007
SHIM ................................................ M009
PIN/RING/CLAMP LEVER .............. M013
CLAMP BRIDGE ............................. M014
CHIPBREAKER............................... M015
ANTI SEIZE LUBRICANT ............... M016
M001
SPARE PARTS
IDENTIFICATION
y IDENTIFICATION OF CLAMP SCREW (Metric coarse right hand screw thread)
a Hexagonal Hole Dimensions

Example
Symbol
L
Length
05
10
Diameter
(Metric)
Pitch
(mm)
M2
M2.5
M3
M4
M5
M6
M8
M10
.4
.45
.5
.7
.8
1.0
1.25
1.5
.197
.394
Example
Symbol
d
Screw
Diameter
050
060
M5
M6
e Dimensions
HBH

.079
.098
.118
.157
.197
.236
HFC

.079
.098
.118
.157
.197
.236
Button
Head
Flat Head
Socket
Head
Symbol
Hexagonal Hole
Dimensions
Screw Head
Pan Head
Geometry
Flat Head
(Flat Head)
H
Symbol
With Slot
JIS
Standard
Set Screw
(Cut Point)
Geometry
Set Screw
(Cone Point)
S
Symbol
With Cross Hole
Set Screw
(Dog Point)
Geometry
Set Screw
(Flat Point)
y IDENTIFICATION OF WRENCH
Standard
SPARE PARTS
R L Wrench
M002
Long
L L Wrench
Hexagonal Wrench
Symbol
Symbol
Wrench
HKY
TKY
NKY
TIP
Hexagonal Wrench
Torx Wrench
15
20
25
30
40
50
60
e
.059
.079
.098
.118
.157
.197
.236
Torx Wrench
Symbol
06
08
10
15
20
25
27
e
.067
.091
.106
.130
.150
.173
.195
Torx plus Wrench

Size
Symbol
Size
T6
T8
T10
T15
T20
T25
T27
06
07
08
15
6IP
7IP
8IP
15IP
T T Wrench
Flag
F
FS Wrench
Flag
W Wrench
Torx Wrench
Torx plus Wrench
Driver
HSC
.059
.079
.098
.118
.157
.197
.236
.315
HSo
.035
.051
.059
.079
.098
.118
.157
.197
SPARE PARTS
CLAMP SCREW
Dimensions (inch)
a
AJS3010T10 .197
4012T15 .276
5014T25 .315
M30.5
M40.7
M50.8
Torque
' (lbf-in)
.394 .059 T10 120 22

.472 .087 T15 120 31
.551 .106 T25 120 66
Tool Holder
DOUBLE CLAMP Type Holder
AJX Type Cutter
PMC Type Cutter
BC5
.354
.717
.335 .669
BLS02
03
04
05
06
08
12
BRS105
.165
.235
.268
.294
.317
.375
.474
.312
M3
M4
M5
M5
M5
M6
M8
M50.8

.270

.335

.356

.504

.610

.803

.969
.543 .118
CAS51T
.312
M50.8
.748 .197 T25
10 75
* CS250560T
300790TS
.154
.185
.161
.217
.189
.217
.189
.236
.224
.248
.276
M2.50.45
M30.5
M30.5
M3.50.6
M3.50.6
M3.50.6
M3.50.6
M40.7
M40.7
M4.50.75
M50.8
.205
.276
.315
.276
.276
.331
.354
.354
.433
.433
.433
60
90
90
60
90
60
90
90
60
90
90
8.9 AL Type Holder

MMTI Type Holder
18
MILLING TOOLS Series
8.9
31
22
31
22
31
31
44
66
DC0520T
0621T
.335
.413
M50.8
M61.0
.886 .098 T15

.984 .157 T20

31
44

DOUBLE CLAMP DIMPLE BAR
HSK-T Tool Holder
DGS51
.453
M50.8
.748 .157 .157
62
HSK-T Tool Holder
*
*
*
300890T
350760T
350790T
350860T
350990T
400990T
401160T
451190T
501290T
.098
.089
.081
.157
.093
.157
.093
.110
.177
.114
.138
T08
T15
T20
T20
T20
T30
T30
T25 120
T8
T10
T8
T15
T10
T15
T10
T15
T15
T20
T25
70
F Type Boring Bar
18
27
35
44
53
58
58
66
MBN Type
MBD Type
BF407 Type Cutter
SPARE PARTS
Order
Number
Geometry
M003
SPARE PARTS
SPARE PARTS
CLAMP SCREW
Order
Number
Geometry
M004
Right-Hand Screw
Left-Hand Screw
.220
M40.7
.295
GTS1
2
3
.220
.310
.350
6-40UNF .500
10-32UNF .750
10-32UNF .750
GY05016S
.343
M50.8
GY06013M
.472
M61.0
JSS6
7
.272
.315
LLCS106
108
.236
.315
Torque
' (lbf-in)
.051 T10 90 22

T10
T20
T20
Tool Holder
AL Type Holder
AL Type Boring Bar

14
45
45
MTVO Type Tool Holder

STHN Type Boring Bar
.630
.138 T20 90
40
GY Holder
.709
.197 T30
53
GY Holder
M60.75 .177
M70.75 .173
.059 .031
.059 .039

SP Type Holder
M61
.650
M81.25 .827
.138 .098
.256 .118
19
29
HSK-T Tool Holder
M101.5
M81.25
M70.75
M70.75
M60.75
M70.75
1.260
.945
.551
.709
.433
.512
.472
.335
.236
.276
.157
.236
.472
.335
.197
.276
.157
.157
.197
.157
T25
T25
T15
T25

80
73
75
75
44
75
UG Holder
LS0622T
M60.75
.866
.315
.315 T15
53
AHX640W Type Cutter
NS251
401
.142
.228
*
*
d
d
d
d
LS21
24
10T
15T
19T
10TS
Hexagonal Hole on
*Without
Right-Hand Screw
Right-Hand Screw
dTorx Screw
Left-Hand Screw
SPARE PARTS
FC400890T
Dimensions (inch)
M2.50.45 .276
M40.7 .236

.087 60 6.2 SMALL TOOLS

.142 60 31
CLAMP SCREW
Dimensions (inch)
Torque
' (lbf-in)
Order
Number
NS402W
403W
404W
.230
.230
.228
M40.7
M40.7
M40.7
.394
.472
.394

.087
.087
.087
NS501W
502W
.315
.315
M50.8
M50.8
.630
.787

.098 120 19
.098 120 19
RS3008TS
3008T
3510T
4015T
5020T
6025T
8030T
S2
S3
.169 M30.35 .331 .079 T8

.169 M30.35 .339 .079 T8
.197 M3.50.35 .394 .091 T10
.236
M40.5 .551 .106 T15
M50.5 .646 .142 T20
.319
.374 M60.75 .846 .165 T25
.472 M80.75 .984 .197 T30
.157 M2.50.45 .256 .091 .079
.177 M30.5 .303 .094 .079
61
61
61
61
61
61
61
92
92
13
13
22
29
44
66
88
14
13
SRF Type Cutter
SETS51
61
.268
.315
M50.8
M61
.583 .059
.787 .071

31
44
HSK-T Tool Holder

MMTE Type Holder
MMTI Type Holder
SLCS105
.394
M50.8
.984 .248 .157
S34
S46
SRS5
TPS20
22
22S
25
25-1
35
4
4S
43

.264
M50.8
.106
.118
.118
.130
.130
.209
.209
.209
.209
M20.4
M2.20.45
M2.20.45
M2.50.45
M2.50.45
M3.50.6
M40.7
M40.7
M40.7
6.2 SMALL TOOLS

6.2
6.2
SMALL TOOLS
90 62
.078
.094

.630 .138
T20
44
.138
.185
.165
.217
.256
.453
.315
.276
.394
6IP
7IP
7IP
7IP
7IP
15IP
15IP
15IP
15IP
60
60
60
60
60
60
60
60
60
5.3 MILLING TOOLS Series

5.3
5.3
8.9
8.9
31
31
31
31
10-32UNF .313
1/4-28UNF .500

T15
T20
60
60
90
Tool Holder
.051
.063
.063
.067
.067
.110
.102
.102
.102
M Type Tool Holder

M Type Boring Bar
SPARE PARTS
Geometry
M005
SPARE PARTS
SPARE PARTS
CLAMP SCREW
a
TS16
2
2A
2C
d
2D
21
22
25
d
25D
25H
202
253
254
255
3
3D
3SB
31D
32
33
35
35D
351
4S
4SL
4
4D
4SB
4SBL
4SBLL
42
43
44
406
407
450
5S
5
5L
52
53
54
55
6S
6
TSS04005
.098
.106
.106
.106
.150
.106
.118
.130
.172
.142
.106
.130
.130
.138
.154
.197
.173
.189
.154
.154
.189
.209
.189
.213
.213
.213
.220
.228
.228
.228
.213
.213
.213
.213
.213
.232
.268
.268
.268
.268
.268
.268
.268
.335
.335
M1.60.35
M20.4
M20.4
M20.4
M20.4
M20.4
M2.20.45
M2.50.45
M2.50.45
M2.50.45
M20.4
M2.50.45
M2.50.45
M2.50.45
M30.5
M30.5
M30.5
M30.5
M30.5
M30.5
M3.50.6
M3.50.6
M3.50.6
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M4.50.75
M50.8
M50.8
M50.8
M50.8
M50.8
M50.8
M50.8
M61.0
M61.0
M40.7
.126
.181
.177
.150
.209
.134
.197
.217
.244
.217
.217
.177
.276
.295
.236
.236
.315
.283
.295
.264
.256
.472
.283
.276
.315
.315
.303
.354
.413
.571
.236
.394
.472
.610
.354
.512
.354
.354
.591
.315
.630
.472
.413
.512
.630
.197
.063
.055
.047
.055
.076
.055
.047
.067
.087
.079
.071
.067
.067
.063
.079
.091
.079
.087
.079
.079
.094
.110
.094
.093
.096
.102
.098
.105
.105
.105
.102
.102
.102
.102
.102
.142
.115
.126
.115
.126
.126
.126
.126
.173
.173
T6
T6
T6
T6
T6
T6
T6
T8
T8
T8
T6
T8
T8
T8
T8
T10
T8
T10
T8
T8
T10
T15
T10
T15
T15
T15
T15
T15
T15
T15
T15
T15
T15
T15
T15
T20
T25
T25
T25
T25
T25
T25
T25
T30
T30
T8
*
*
*
*
*
*
*
*
*
SPARE PARTS
*
*
*
*
M006
Dimensions (inch)
Order
Number
Geometry
Torque
' (lbf-in)
60
60
60
60
82
60
60
60
82
60
60
60
60
60
60
82
80
82
60
60
60
60
60
80
80
60
82
80
80
80
60
60
60
60
60
60
80
60
80
60
60
60
60
60
60
5.3
5.3
5.3
5.3
5.3
5.3
5.3
8.9
8.9
8.9
5.3
8.9
8.9
8.9
8.9
22
13
22
8.9
8.9
22
31
22
31
35
31
31
31
31
31
31
31
31
31
31
44
66
66
66
66
66
66
66
89
89
Tool Holder
SP Type Tool Holder
AL Type Tool Holder
SR Type Tool Holder
SMALL TOOLS
DIMPLE BAR
S Type Boring Bar
MICRO-DEX
GY Holder
MMTI Type Holder
F Type Boring Bar
HSK-T Tool Holder
TAF Drill
PMF Type Cutter
CLAMP SCREW
Geometry
Dimensions (inch)
Order
Number
WCS503507H
.248
M50.5
Torque
' (lbf-in)
.276 .130 .138
Tool Holder
44 ASX445 Type Cutter

ASX400 Type Cutter
PMR Type Cutter
XNS35
10-32UNF
.625
.220 .220 .094
36
10-32UNF
.750
.250 .250 .094
1/4-28UNF
.750
.310 .310 .125
46
47
1/4-28UNF
.875
.280 .280 .125
48
1/4-28UNF 1.000
.370 .370 .125
58
5/16-24UNF 1.000
.500 .280 .156
59
5/16-24UNF 1.120
.470 .410 .156
5/16-24UNF 1.125
.500 .500 .156
510
610
3/8-24UNF 1.250
.500 .500 .188
WS254012T
.157
M2.50.45 .453 .087 T8
254013T
.157
M2.50.45 .492 .087 T8
M2.50.45 .531 .087 T8
254014T
.157
254015T
.157
M2.50.45 .571 .087 T8
254016T
.157
M2.50.45 .610 .087 T8
304517T
.177
M30.5 .650 .134 T10
304518T
.177
M30.5 .689 .134 T10
355520T
.217
M3.50.6 .768 .154 T15
355521T
.217
M3.50.6 .807 .154 T15
406023T
.236
M40.7 .866 .173 T25
406024T
.236
M40.7 .906 .173 T25
508026T
.315
M50.8 .984 .205 T27
508027T
.315
M50.8 1.024 .205 T27

80
80
80
80
80
60
60
60
60
60
60
60
60
30
30
45
45
45
70
70
70
135
18
18
18
18
18
31
31
49
49
75
75
110
110
M Type Tool Holder

M Type Boring Bar
MTVO Type Holder
TAW Drill
SET BOLT
Right-Hand
Screw
Right-Hand
Screw
Right-Hand
Screw
Right-Hand
Screw
HDS10031
Dimensions (inch)
a
a'
M10x1.0
M10x1.5
Torque
(lbf-ft)
Tool Holder
1.220 .551 .472 .197 6.6 PMF Type Cutter
SPARE PARTS
Order
Number
Geometry
HDSU37513 5/16-32UNEF 3/8-24UNF 1.260 .472 .433 .156 6.1 BOE Type Cutter
BRP Type Cutter
M007
SPARE PARTS
SPARE PARTS
SET BOLT
Geometry
Order
Number
Dimensions (inch)
a
BOE4S06U
.562
HFF08043H
.433
Torque
' (lbf-ft)
3/8-24UNF 1.358 .374 .313 60
M81.25
1.693 .197 .197 90
29
Tool Holder
BOE Type Cutter
6.1 AXD4000 Type Cutter
SPARE PARTS
BXD4000 Type Cutter
M008
HSCU25014H
37513H
50014H
62516H
75016H
.370
.562
.750
.938
1.125
1/4-28UNF
3/8-24UNF
1/2-20UNF
5/8-18UNF
3/4-16UNF
1.647
1.625
1.875
2.250
2.375
.250
.375
.500
.625
.750
.156
.250
.375
.500
.625

10
29
59
80
110
AJX Type Cutter

APX3000 Type Cutter
APX4000 Type Cutter
AXD7000 Type Cutter
BAP3500 Type Cutter
BXD4000 Type Cutter
HSCUF25013
37513
37520
50014
50028
62518
62528
75018
HSCUC62523
75025
.375
.562
.562
.750
.750
.938
.938
1.125
.938
1.125
1/4-28UNF
3/8-24UNF
3/8-24UNF
1/2-20UNF
1/2-20UNF
5/8-18UNF
5/8-18UNF
3/4-16UNF
5/8-11UNS
3/4-10UNS
1.500
1.625
2.375
1.875
3.248
2.375
3.373
2.500
2.875
3.250
.250
.375
.375
.500
.500
.625
.625
.750
.625
.750
.188
.313
.313
.375
.375
.500
.500
.625
.500
.625

10
29
29
59
59
80
80
110
80
110
APX4000 Type Cutter

SPX Type Cutter
HSC08030H
10030H
12035H
16040H
.512
.630
.709
.945
M81.25
M101.5
M121.75
M162.0
1.496
1.575
1.850
2.205
.315
.394
.472
.630
.197
.236
.394
.551

18
29
59
110
AJX Type Cutter

APX3000 Type Cutter
APX4000 Type Cutter
AXD4000 Type Cutter
AXD7000 Type Cutter
BXD4000 Type Cutter
HSC10035
10050
12035
12040
12045
12070
16040
16065
16080
20040
20090
MBAU75016H
100016H
.630
.630
.709
.709
.709
.709
.945
.945
.945
1.181
1.181
2.000
2.593
M101.5
M101.5
M121.75
M121.75
M121.75
M121.75
M162.0
M162.0
M162.0
M202.5
M202.5
3/4-16UNF
1-14UNS
1.772
2.362
1.850
2.047
2.244
3.228
2.205
3.189
3.780
2.362
4.331
2.188
2.188
.394
.394
.472
.472
.472
.472
.630
.630
.630
.787
.787
.563
.563
.315
.315
.394
.394
.394
.394
.551
.551
.551
.669
.669
.625
.625

29
29
59
59
59
59
110
110
110
236
236
236
384
APX4000 Type Cutter

PMF Type Cutter
PMR Type Cutter
SPX Type Cutter
VFX6 Type Cutter
MBA20040H
24045H
1.969
2.559
M202.5
M243.0
2.126 .551 .669 236

2.323 .551 .669 384
AJX Type Cutter

APX4000 Type Cutter
AXD4000 Type Cutter
AXD7000 Type Cutter
BXD4000 Type Cutter
AJX Type Cutter

AXD7000 Type Cutter
SHIM
Dimensions (inch)
Order
Number
DCSVN32
.375
.125
.031
.047
ICSN322
432
433
533
633
.375
.500
.500
.625
.750
.125
.188
.188
.188
.188
.031
.031
.047
.047
.047
.031
.031
.047
.047
.047
.031
.031
.047
.047
.047
.031
.031
.047
.047
.047
M Type Tool Holder

M Type Boring Bar
IDSN322
433
533
543
.375
.500
.625
.625
.125
.188
.188
.250
.031
.047
.047
.047
.031
.047
.047
.047

M Type Tool Holder

M Type Boring Bar
IRSN32
43
44
63
.375
.500
.500
.750
.125
.188
.250
.188

M Type Tool Holder
.375
.375
.500
.500
.500
.625
.750
.750
.750
.750
1.000
.375
.375
.375
.375
.375
.375
.500
.500
.500
.625
.625
.750
.750
.125
.125
.188
.188
.250
.188
.188
.188
.250
.250
.250
.125
.125
.125
.188
.188
.188
.188
.188
.188
.188
.188
.188
.188
.031
.047
.047
.063
.047
.047
.047
.063
.047
.063
.094
.031
.047
.063
.031
.047
.063
.031
.063
.125
.047
.063
.047
.094
.031
.047
.047
.063
.047
.047
.047
.063
.047
.063
.094
.031
.047
.063
.031
.047
.063
.031
.063
.125
.047
.063
.047
.094
.031
.047
.047
.063
.047
.047
.047
.063
.047
.063
.094
.031
.047
.063
.031
.047
.063
.031
.063
.125
.047
.063
.047
.094
.031
.047
.047
.063
.047
.047
.047
.063
.047
.063
.094

M Type Tool Holder

M Type Boring Bar
ISSN322
323
433
434
443
533
633
634
643
644
846
ITSN322
323
324
332
333
334
432
434
438
533
534
633
636
Tool Holder
M Type Tool Holder

M Type Boring Bar
SPARE PARTS
Geometry
M009
SPARE PARTS
SPARE PARTS
SHIM
Geometry
*
*
*
*
*
IVSN322
432
433
.375
.500
.500
.125
.188
.188
.031
.031
.047
.031
.031
.047

M Type Tool Holder

M Type Boring Bar
IWSN322
432
533
.375
.500
.625
.125
.188
.188
.031
.031
.047
.031
.031
.047
.031
.031
.047

M Type Tool Holder

M Type Boring Bar
LLSCN32
33
42
LLSCP32
42
.375
.375
.500
.375
.500
.125
.188
.125
.125
.125
.016
.016
.031
.016
.031
.016
.016
.031
.016
.031
.031
.031
.047
.031
.047
.031
.031
.047
.031
.047

HSK-T Tool Holder
LLSDN32
42
43
LLSDP42
.375
.500
.500
.500
.125
.125
.188
.125
.031
.031
.031
.031
.047
.047
.047
.047


HSK-T Tool Holder
LLSRN123
.386
.125

HSK-T Tool Holder
LLSSN42
.500
.500
.125
.125
.031
.031
.031
.031
.047
.047
.047
.047

LLSTN32
33
LLSTP32
.375
.375
.375
.125
.188
.125
.016
.016
.016
.031
.031
.031
.047
.047
.047


LLSWN32
33
42
LLSWP42
.375
.375
.500
.500
.125
.188
.125
.125
.016
.016
.016
.016
.031
.031
.031
.031
.047
.047
.047
.047


SPARE PARTS
* * LLSSP42
*
*
*
*
M010
Dimensions (inch)
Order
Number
Tool Holder
SHIM
Dimensions (inch)
Order
Number
SPSCN42
.500
.125
SP Type Tool Holder
SPSVN32
.317
.125
.012
.012
SP Type Tool Holder

HSK-T Tool Holder
SPSSN42
.468
.125
SP Type Tool Holder
SPSTN32
.352
.125
SP Type Tool Holder
SPSDN32
.342
.125
SP Type Tool Holder
Tool Holder
SPARE PARTS
Geometry
M011
SPARE PARTS
SPARE PARTS
SHIM
SPARE PARTS
Geometry
M012
Dimensions (inch)
Order
Number
STASX400N
.433
.118
ASX400 Type Cutter
STASX445N
.424
.118
ASX445 Type Cutter
Tool Holder
PIN / RING / CLAMP LEVER

Order
Number
Geometry
Tool Holder
.262
.304
.016
.026
.041
.045
MMTE Type Holder

HSK-T Tool Holder
NL23
33
33L
34
34L
43
44
46
56
58
68
68L
810
BCP141
8 32
10 32
10 32
10 32
10 32
10 32
.250 28
.250 28
.313 24
.313 24
.375 24
.375 24
.438 20
.118
.313
.347
.406
.453
.500
.422
.516
.688
.703
.844
.875
.938
.813
.055
.063
.078
.078
.078
.078
.078
.094
.094
.125
.125
.141
.141
.156
.220
M Type Tool Holder

M Type Boring Bar
LLCL14
24
112
.185
.185
.138
.528
.638
.512
.520
.583
.531
HSK-T Tool Holder
LLP14
23
24
.285
.219
.285
.258
.191
.258
.228
.268
.358

HSK-T Tool Holder
CR4
5
a
c
*
*
SP Type Holder
HSK-T Tool Holder
SPARE PARTS
Dimensions (inch)
M013
SPARE PARTS
SPARE PARTS
CLAMP BRIDGE
SPARE PARTS
Geometry
M014
Order
Number
Dimensions (inch)
Tool Holder
AMS3
4
5
.276
.354
.394
.472
.531
.590
.118
.118
.136
.130
.150
.197

CL6
7
9
12
19
20
24
30
DCK2211
2613
3113
.310
.310
.430
.430
.310
.375
.491
.430
.433
.512
.512
.580
.640
.750
.880
.550
.730
1.000
1.000
.866
1.043
1.220
.440
.310
.660
.660
.310
.380
.785
.660
.259
.289
.354
.062
.062
.344
.344
.187
.125
.453
.344
.357
.407
.472
.094

.125
.125

.136
.125

DGK2R/L
3R/L
4R/L
5R/L
6R/L
.539
.539
.539
.539
.539
1.043
1.043
1.043
1.043
1.043
.047
.079
.118
.157
.197
.354
.354
.354
.354
.354

KGC1
.402
.590
M70.75
UG Holder
MTK1R/L
.512
.689
.197
.472
HSK-T Tool Holder
SETK51
61
.268
.350
.571
.713
.114
.161
.315
.339

MMTE Type Holder

MMTI Type Holder
HSK-T Tool Holder
SRK1R
.370
.827
.216
.295

AJX Type Cutter
PMC Type Cutter
M Type Tool Holder

M Type Boring Bar
MTVO Type Tool Holder
DOUBLE CLAMP Holder

HSK-T Tool Holder
CHIPBREAKER
Dimensions (inch)
a
Insert
I.C.
Breaker
Width
CBC4
.440
.062
.500
M Type Tool Holder

M Type Boring Bar
CBR4
.421
.560
.120
.500
M Type Tool Holder
CBS3
4
.370
.496
.315
.362
.059
.098
.375
.500
.059
.138
M Type Tool Holder

M Type Boring Bar
CBS3D
4D
.315
.402

.059
.098
.375
.500
.059
.098
M Type Tool Holder
CBT3
.283
.055
.098
.375
.138
M Type Tool Holder

M Type Boring Bar
Tool Holder
SPARE PARTS
Geometry
Order
Number
M015
SPARE PARTS
SPARE PARTS
ANTI SEIZE LUBRICANT
SPARE PARTS
Shape
M016
Order Number
Stock
Volume
(oz)
MK1KS
0.1
TECHNICAL DATA
TROUBLE SHOOTING FOR TURNING ................................................. N002
CHIP CONTROL FOR TURNING ........................................................... N004
EFFECTS OF CUTTING CONDITIONS FOR TURNING........................ N005
FUNCTION OF TOOL FEATURES FOR TURNING............................... N007
FORMULAS FOR CUTTING................................................................... N011
TROUBLE SHOOTING FOR MILLING................................................... N012
FUNCTION OF TOOL FEATURES FOR FACE MILLING ..................... N013
FORMULAS FOR MILLING .................................................................... N016
TROUBLE SHOOTING FOR END MILLING .......................................... N017
END MILL FEATURES AND SPECIFICATION...................................... N018
END MILL TYPE AND GEOMETRY ....................................................... N019
PITCH SELECTION OF PICK FEED ...................................................... N020
TROUBLE SHOOTING FOR DRILLING ................................................ N021
DRILL WEAR CONDITION AND CUTTING EDGE DAMAGE ............... N022
DRILL TERMINOLOGY AND CUTTING CHARACTERISTICS ............. N023
FORMULAS FOR DRILLING.................................................................. N026
TOOL WEAR AND DAMAGE ................................................................. N027
MATERIAL CROSS REFERENCE LIST ................................................ N028
SURFACE ROUGHNESS ....................................................................... N032
HARDNESS COMPARISON TABLE...................................................... N033
CUTTING TOOL MATERIALS................................................................ N034
GRADE CHAIN ....................................................................................... N035
GRADE COMPARISON TABLE ............................................................. N036
INSERT CHIP BREAKER COMPARISION TABLE ............................... N041
N001
TECHNICAL DATA
TROUBLE SHOOTING
Thermal cracking
Worsening Dimensional Accuracy

Poor Surface
Finish
Heat
Generation
TECHNICAL DATA
N002
Dry
a
Wet
Improper insert
tolerance
Large cutting resistance

and cutting edge ank
Improper cutting
conditions
Welding occurs
Improper cutting
edge geometry
Wet
a
Vibration occurs
Improper cutting
conditions
Improper cutting
edge geometry
Lack of rigidity
Cutting heat creates

deterioration in
machining accuracy
and tool life
Wet
Built-up edge
Worsening
surface
roughness
Lack of cutting
edge strength
Improper tool grade
Machine with Inadequate

Horsepower and Rigidity
Lead Angle
Corner Radius
Rake Angle
Depth of Cut
Feed Rate
Improper cutting
conditions
Machining accuracy
not maintained
adjustment is
necessary each time
Toolholder Overhang
Short Tool Life
Cutting Speed
Improper cutting
edge geometry
Improper tool grade
Dimensional
unevenness
during
machining
Improper cutting
conditions
Chipping and
fracturing of
cutting edge
Down
Installation of the Tool and

Workpiece
Rapid
insert wear
Down
Up
Machine and
Installation of Tool
Improve Tool Holder Rigidity
Improper tool grade
Up
Cutting
Fluids
Honing Strengthens
the Cutting Edge
Class of Insert
(Unground-Ground)
Style and Design

of the Tool
Select Chip Breaker
or
Cutting
Conditions
Do Not Use Watersoluble Cutting Fluid

Determine Dry or
Wet Cutting
ct
Select a Grade with Better

Thermal Shock Resistance
Adhesion Resistance
Trouble
Select a Tougher Grade
Fa
Insert Grade
Selection
Select a Harder Grade
Solutions
FOR TURNING
Lead Angle
Corner Radius
Improper cutting
edge geometry
Wet
a
Dry
a
TECHNICAL DATA
Chip Control
Wide chip control

range
Small chip control

range
Wet
Improper cutting
edge geometry
Broken into
short lengths
and scatter
Improper cutting
edge geometry
Improper cutting
conditions
Vibration occurs
Uncontrolled,
continuous /
tangled
Wet
Improper cutting
edge geometry
Improper cutting
conditions
Vibration occurs
Roughness
(Mild steel)

Burr / Chipping / Roughness
Rake Angle
Depth of Cut
Feed Rate
Cutting Speed
a
Improper cutting
conditions
Improper cutting
conditions
Toolholder Overhang
Improper cutting
conditions
Improper tool grade
Improper cutting
edge geometry
Chipping
(Cast iron)
Down

Workpiece
Burr
Steel,
(Aluminum
alloy )
Down
Up
Machine and
Improve Tool Holder Rigidity
Notch wear occurs
Up
Cutting
Fluids
Honing Strengthens
the Cutting Edge
Class of Insert
(Unground-Ground)
Style and Design

of the Tool
Select Chip Breaker
or
Cutting
Conditions

Determine Dry or
Wet Cutting
ct

Adhesion Resistance
Trouble
Fa
Insert Grade
Selection
Solutions
N003
TECHNICAL DATA
CHIP CONTROL FOR TURNING

y CHIP BREAKING CONDITIONS IN STEEL TURNING
Type
A Type
B Type
C Type
D Type
E Type
Curless
l > 2inch
l < 2inch
1 5 Curl
i 1 Curl
1 curlhalf curl
Small Depth
of Cut
d <.276"
Large Depth
of Cut
d=.276" .591"
Curl Length
l
a Irregular
continuous shape
a Tangle about
tool and workpiece
Note
continuous shape
a Long chips
a Chip
a Regular
scattering
a Chattering
a Poor
nished
surface
a Maximum
Good
Good
a Cutting Speed and Chip Control Range of Chip Breaker

In general, when cutting speed increases, the chip control range tends to become narrower.
vc=330SFM
Feed (IPR)
vc=490SFM
Feed (IPR)
Feed (IPR)
vc=165SFM
Depth of Cut (inch)
Depth of Cut (inch)
Workpiece : AISI 1045 (180HB)
Depth of Cut (inch)
Tool : MTJNR2525M16N
Insert : TNMG332
Dry Cutting
Grade : P10Grade
a Effects of Coolant on the Chip Control Range of a Chip Breaker

If the cutting speed is the same, the range of chip control differs according to whether coolant is used or not.
Coolant : Wet cutting

(Emulsion)
Feed (IPR)
Feed (IPR)
TECHNICAL DATA
Coolant : Dry cutting
Depth of Cut (inch)

Cutting Condition : vc=330SFM
N004
Depth of Cut (inch)
EFFECTS OF CUTTING
CONDITIONS FOR TURNING
y EFFECTS OF CUTTING CONDITIONS
Ideal conditions for cutting are short cutting time, long tool life, and high cutting accuracy. In order to obtain these conditions,
selection of efcient cutting conditions and tool, based on work material, hardness, shape and machine capability is necessary.
y CUTTING SPEED
Cutting speed effects tool life greatly. Increasing cutting speed increases cutting temperature and results in shortening tool life.
Cutting speed varies depending on the type and hardness of the work material. Selecting a tool grade suitable for the cutting
speed is necessary.
Cutting Speed (SFM)

Tool Life Standard : VB = .012inch
Feed : .012IPR
Holder : MCLNR-164C
Insert : CNMG432
Dry Cutting
Tool Life (min)
P Class Grade Tool Life
Cutting Speed (SFM)

Tool Life Standard : .012inch
Feed : .012IPR
Holder : MCLNR-164C
Insert : CNMG432MA
Dry Cutting
Tool Life (min)
M Class Grade Tool Life
Tool Life (min)
TECHNICAL DATA
Cutting Speed (SFM)
Workpiece : AISI No.45B Cast Iron

Tool Life Standard : .012inch
Feed : .012IPR
Holder : MCLNR-164C
Insert : CNMG432
Dry Cutting
K Class Grade Tool Life
a Effects of Cutting Speed

1. Increasing cutting speed by 20% decreases tool life to 1/2. Increasing cutting speed by 50% decreases tool life to 1/5.
2. Cutting at low cutting speed (65130 SFM) tends to cause chattering. Thus, tool life is shortened.
N005
TECHNICAL DATA
EFFECTS OF CUTTING
CONDITIONS FOR TURNING
y FEED
In cutting with a general holder, feed is the distance a holder moves per workpiece revolution. In milling, feed is the distance a
machine table moves per cutter revolution divided by number of inserts. Thus, it is indicated as feed per tooth. Feed rate
relates to nished surface roughness.
a Effects of Feed
tool life.
2. Increasing feed rate increases cutting temperature and
ank wear. However, effects on the tool life is minimal
compared to cutting speed.
Flank Wear (inch)
1. Decreasing feed rate results in ank wear and shortens
3. Increasing feed rate improves machining efciency.

Feed (IPR)
Cutting Conditions Workpiece : AISI 4340
Grade : STi10T
Depth of Cut ap=.040(inch) Cutting Speed vc=660(SFM)
Cutting Time Tc=10min
Feed and Flank Wear Relationship in Steel Turning
y DEPTH OF CUT
a Effects of Depth of Cut

1. Changing depth of cut doesn't effect tool life greatly.
2. Small depths of cut result in friction when cutting the
hardened layer of a workpiece. Thus tool life is
Flank Wear (inch)
Depth of cut is determined according to the required stock removal, shape of workpiece, power and rigidity of the machine and
tool rigidity.
shortened.
Depth of Cut (inch)
3. When cutting uncut or cast iron surfaces, the depth of

cut needs to be increased as much as the machine
power allows to avoid cutting impure hard layer with the
Cutting Conditions

Feed f=.008(IPR)
Cutting Time Tc=10min
Grade : STi10T
Cutting Speed vc=660(SFM)
tip of cutting edge which prevents chipping and

abnormal wear.
Depth of Cut and Flank Wear Relationship in Steel Turning
TECHNICAL DATA
Depth of Cut
Uncut Surface
Roughing of Surface Layer that Includes Uncut Surface
N006
FUNCTION OF TOOL FEATURES

FOR TURNING
y RAKE ANGLE
Rake angle is a cutting edge angle that has large effects on cutting resistance, chip disposal, cutting temperature and tool life.
Vertical
Force (N)
Positive Insert
Cutting
Temperature (C)
Tool Life (min)
(+ )
5
gle 1
e An
Rak
6
-10
gle
gle
e An
e An
Rak
Rak
Positive Rake
Angle
Negative Rake
Angle
(- )
Negative
Insert
Depth of Cut .079inch

Feed .008IPR
Cutting Speed 330SFM
Depth of Cut .079inch

Feed .008IPR
Cutting Speed 330SFM
1.Increasing rake angle in the positive (+) direction

improves sharpness.
2.Increasing rake angle by 1 in the positive (+)
direction decreases cutting power by about 1%.
3.Increasing rake angle in the positive (+) direction
lowers cutting edge strength and in the negative
(-) direction increases cutting resistance.
Rake Face Mean

Temperature
Rake Angle ()
Cutting Speed (SFM)
Rake Angle and Tool Life
of Rake Angle
Cutting Resistance
Vertical Force
Cutting Conditions
Workpiece : Alloy steel Grade : STi10T
Dry Cutting
Cutting Conditions
Grade : STi10
Feed : .013IPR
Workpiece : Alloy steel
Chip Disposal and Rake Angle

a Effects
Tool Life Standard : VB = .016inch

Depth of Cut : .039inch Feed = .013IPR
Cutting
Speed (SFM)
Tool Life
Standard
VB = .016
inch
When to Increase Rake Angle

in the Negative (-) Direction
u Hard workpiece.
u When cutting edge strength is
required such as in
interrupted cutting and uncut
surface cutting.
Effects of Rake Angle on

Cutting Speed, Vertical Force,
and Cutting Temperature
When to Increase Rake Angle

in the Positive (+) Direction
u Soft workpiece.
u Workpiece is easily machined.
u When workpiece or the
machine have poor rigidity.
y FLANK ANGLE
Flank angle prevents friction between ank face and workpiece resulting in smooth feed.
Flank Wear (inch)
Rake Angle 6
Large Flank Angle
D.O.C
(Same)
D.O.C
(Same)
Small
Flank Wear
Large
Flank Wear
Small Flank Angle
Flank angle creates a space between tool and workpiece.

Flank angle relates to ank wear.
a Effects
of Flank Angle
1.Increasing ank angle decreases ank wear

occurrence.
2.Increasing ank angle lowers cutting edge
strength.
Flank Angle $
Cutting Conditions
Flank Angle ($)
Workpiece : Alloy steel (200HB)

Grade : STi20
Feed : .013IPR
Cutting Time : 20min
Flank Angle and Flank Wear Relationship
When to Decrease Flank Angle

u Hard workpieces.
u When cutting edge strength
is required.
re
ctu
Fra
TECHNICAL DATA
Wear Depth
Wear Depth
When to Increase Flank Angle

u Soft workpieces.
u Workpieces suffer from
work hardening easily.
N007
TECHNICAL DATA

FOR TURNING
y SIDE CUTTING EDGE ANGLE (LEAD ANGLE)
Side cutting edge angle lower impact load and effect feed force, back force, and chip thickness.
1.1
5B
f = Same

Grade : STi120
Feed : .008IPR
Dry Cutting
f = Same
0.97
h
kr = 30
kr = 15
Side Cutting Edge Angle and Chip Thickness
B : Chip Width
f : Feed
h : Chip Thickness
kr : Side Cutting
Edge Angle
le 15
Ang
0
dge
Angle
ing E
dge
Cutt
ing E
Side
Cutt
Side
kr = 0
0.8
7h
Tool Life (min)
1.04
B
f = Same
a Effects of Side Cutting Edge Angle (Lead Angle)

1. At the same feed rate, increasing the side cutting edge angle increases the chip
contact length and decreases chip thickness. As a result, the cutting force is
dispersed on a longer cutting edge and tool life is prolonged. (Refer to the chart.)
2. Increasing the side cutting edge angle increases force a'. Thus, thin, long
workpieces suffer from bending in some cases.
3. Increasing the side cutting edge angle decreases chip control.
4. Increasing the side cutting edge angle decreases the chip thickness and increases
chip width. Thus, breaking chips is difcult.
When to Decrease Lead Angle
Cutting Speed (SFM)
Side Cutting Edge and Tool Life
When to Increase Lead Angle
A
A
u Finishing with small depth of
u Hard workpieces which
cut.
u Thin, long workpieces.
u When the machine has poor
rigidity.
produce high cutting

temperature.
u When roughing a large
diameter workpiece.
u When the machine has high
rigidity.
a'
Receive force A.
Force A is divided
into a and a'.
y END CUTTING EDGE ANGLE

End cutting edge angle prevents wear on tool and workpiece
surface and is usually 5 15.
End Cutting
Edge Angle
a Effects of End Cutting Edge Angle
TECHNICAL DATA
1. Decreasing the end cutting edge angle increases cutting edge strength,
but it also increases cutting edge temperature.
2. Decreasing the end cutting edge angle increases the back force and
can result in chattering and vibration while machining.
3. Small end cutting edge angle in roughing and large angle in nishing
are recommended.
Side Flank Angle
y CUTTING EDGE INCLINATION

Cutting edge inclination indicates inclination of the rake face. In heavy
cutting, the cutting edge receives extremely large shock at the beginning
of cutting. Cutting edge inclination keeps the cutting edge from receiving
this shock and prevents fracturing. 3 5 in turning and 10 15 in milling
are recommended.
a Effects of Cutting Edge Inclination

1. Negative (-) cutting edge inclination disposes chips in the workpiece
direction, and positive (+) disposes chips in the opposite direction.
2. Negative (-) cutting edge inclination increases cutting edge strength, but
it also increases back force of cutting resistance. Thus, chattering easily
occurs.
N008
Back Relief Angle
True Rake
Angle
()
Cutting Edge
Inclination
Main Cutting Edge
Side Cutting
Edge Angle
End Cutting Edge

Angle
Corner Radius
y HONING AND LAND
Honing Angle
Round Honing
R Honing
C Honing
R Honing
C Honing
Flat Land
Feed Force (N)
Principal Force (N)
Chamfer Honing
Tool Life (min)
Tool Life (Number of Impacts)
Land Width
Honing Width
Honing Width
Honing and land are cutting edge shapes that

maintain cutting edge strength.
Honing can be round or chamfer type. The
optimal honing or / and land width is
approximately 1/2 of the feed.
Land is the narrow at area on the rake or
ank face.
Honing Size (inch)

Grade : P10
Cutting Conditions : vc=525SFM ap=.059inch
f=.018IPR
Honing Size and Tool Life

Due to Fracturing
Honing Size and Tool Life

Due to Wear
Back Force (N)
Honing Size (inch)

Grade : P10
f=.013IPR
R Honing
C Honing
Honing Size (inch)

Grade : P10
f=.017IPR
Honing Size and Cutting Resistance
a Effects of Honing
When to Decrease Honing Size

u When nishing with small
depth of cut and small feed.

u Soft workpieces.
u When the workpiece and the
machine have poor rigidity.
When to Increase Honing Size

u Hard workpieces.
u When the cutting edge
strength is required such as

for uncut surface cutting and
interrupted cutting.
rigidity.
TECHNICAL DATA
1.Enlarging the honing increases cutting edge strength, and reduces fracturing.
2.Enlarging the honing increases ank wear occurrence. Honing size doesn't affect rake wear.
3.Enlarging the honing increases cutting resistance and chattering.
N009
TECHNICAL DATA

FOR TURNING
Finished Surface (!inch)
y CORNER RADIUS
Corner radius effects the cutting edge strength
and nished surface. In general, a corner
radius 2 3 times the feed is recommended.
Feed
Theoretical
Surface
Roughness
Depth
of Cut
Feed
Feed (IPR)
Corner Radius (inch)

Theoretical
Surface
Roughness
Depth
of Cut

Grade : P20
Cutting Speed : vc=395SFM ap=.020inch
Corner Radius Size and Tool Life Due to Fracturing
a Effects of Corner Radius
Flank Wear
Crater Wear
(Crater Depth)
When to Increase Corner Radius
u Finishing with small depth of
u When the cutting edge
cut.
u Thin, long workpieces.
u When the machine has poor
rigidity.
strength is required such as

in interrupted cutting and
uncut surface cutting.
u When roughing a workpiece
with large diameter.
rigidity.
Feed (IPR)
TECHNICAL DATA
a Corner Radius and Chip Control Range

Insert : TNGG331R
TNGG332R
TNGG333R
(STi10T)
(Side Cutting Edge angle 3)
Cutting Speed : vc=330SFM
Dry Cutting
Depth of Cut (inch)
(Note) Please refer to page F004 for chip shapes (A, B, C, D, E).
N010

(200HB)
Grade : P10
Cutting
Conditions : vc=460SFM
ap=.079inch
f=.008IPR
Tc=10min
Corner Radius Size and Tool Wear
When to Decrease Corner Radius
1.Increasing the corner radius improves the surface

nish.
2.Increasing the corner radius improves cutting
edge strength.
3.Increasing the corner radius too much increases
the cutting resistance and causes chattering.
4.Increasing the corner radius decreases ank and
rake wear.
5.Increasing the corner radius too much results in
poor chip control.
Crater Wear Depth (inch)

(280HB)
Grade : P10
Cutting
Conditions : vc=330SFM
ap=.079inch
f=.013IPR
Flank Wear Width (inch)
Tool Life (Number of Impacts)
Corner Radius and Finished Surface
FORMULAS FOR CUTTING

y CUTTING SPEED (vc)
(SFM)
y FEED ( f )
vc (SFM)
Dm (inch)
) (3.14)
-1
n (min )
: Cutting Speed
: Workpiece Diameter
: Pi
: Main Axis Spindle Speed
: Feed per Revolution

f (IPR)
I (inch/min) : Cutting Length per Min.
-1
n (min )
(IPR)
(Problem) What is the cutting speed when the main axis spindle speed is
-1
700 min and external diameter is & 2" ?
(Problem) What is the feed per revolution when the main axis spindle speed is
-1
500min and cutting length per minute is 4.72 inch/min ?
(Answer) Substitute )=3.14, Dm =2, n =700 into the formula.
(Answer) Substitute n=500, I=4.72 into the formula.
365SFM
.009IPR
Cutting speed is 365SFM.
Dm
y THEORETICAL FINISHED SURFACE ROUGHNESS (h)
y CUTTING TIME (Tc)
(min)
The answer is .009IPR.
Tc (min)
: Cutting Time
Im (inch)
: Workpiece Length
I (inch/min) : Cutting Length per Min.
(!inch)
h (!inch) : Finished Surface

Roughness
f (IPR) : Feed per Revolution
Re (inch) : Insert Corner Radius
(Problem) What is the cutting time when 4 inch workpiece is machined at

-1
1000min with feed= .008IPR ?
(Problem) What is the theoretical nished surface roughness when the insert
corner radius is .031inch and feed is .008IPR ?
(Answer) First, calculate the cutting length per min. from the feed and spindle speed.
(Answer) Substitute f= .008 IPR, R= .031 into the formula.
I = f n = .008 1000 = 8inch/min
!inch
Substitute the answer above into the formula.
Tc = Im =
l
4
8
The theoretical nished surface roughness is 258!inch.
= 0.5min
Feed
Feed
0.5 x 60 = 30 (sec.) The answer is 30 sec.

Theoretical
Surface
Roughness
Depth
of Cut
Theoretical
Surface
Roughness
TECHNICAL DATA
Depth
of Cut
N011
TECHNICAL DATA
TROUBLE SHOOTING FOR MILLING
a
a
Improper cutting
conditions
Lack of cutting
edge strength
Thermal cracking
occurs
Poor Surface Finish

Burr / Chipping
Chip Control
TECHNICAL DATA
N012
Not parallel
or irregular
surface
Burr
a
a
a
a
a
a
Wet
a
a
a
a
a
a
Tool clearance
a
a
a
a
a
a
Poor sharpness
Corner angle is
too small
a
a
Vibration occurs
Welding occurs
Chip thickness
is too thin
Cutter diameter
is too small
Poor chip
disposal
Wet
A large corner
angle
Improper cutting
conditions
Poor chip
disposal,
chip jamming
and chip
packing
Dry
Poor sharpness
Chipping
Workpiece
bending
Large back
force
Chip thickness
is too large
Cutter diameter
is too large
Poor run-out
accuracy
Vibration occurs
Wet
Lack of rigidity
Welding occurs
Built-up edge
occurs
Worsening
surface
roughness

Improper cutting
edge geometry
Improper cutting
conditions
Improper cutting
conditions
Shorten Tool Overhang
Run-out Accuracy
Use of a Wiper Insert
Wider Chip Pocket
Down
Decrease the Number of Teeth
Honing Strengthens
the Cutting Edge
Cutter
Diameter
Corner Angle
Rake Angle
Engage Angle
Up

Determine Dry or
Wet Cutting
Depth of Cut
Feed Rate
Cutting Speed

Adhesion Resistance
Down
Up
Improper tool grade
Chipping and
fracturing of
cutting edge
Up
Cutting
Fluids
Machine and
Workpiece
Short Tool Llfe
Rapid
insert wear
Style and Design

of the Tool
Cutting
Conditions
Improve Cutter Rigidity
Improper tool grade
rs
to
c
Fa
Trouble
Insert Grade
Selection
Solutions
a
a
a
Wet

FOR FACE MILLING
y FUNCTION OF EACH CUTTING EDGE
ANGLE IN FACE MILLING
Type of Angle
Symbol
Function
Effect
A.R
Determines chip
disposal direction.
Positive : Excellent machinability.
Determines
Negative : Excellent chip disposal.
Axial Rake Angle

Corner Angle
Axial Rake Angle
Lead
Angle
Radial Rake Angle R.R sharpness.

Corner Angle
Wiper Edge
CH
Determines chip
thickness.
Large : Thin chips and small

cutting impact.
Large back force.
Positive(large) :
Excellent machinability.
Minimal welding.
Negative(large) : Poor machinability. Strong cutting edge.
Main Cutting Edge

Cutting Edge
Inclination
True Rake Angle
True Rake Angle
Determines
actual
sharpness.
Cutting Edge
Inclination
Determines chip Positive (large) :

Excellent chip disposal.
disposal
Low cutting edge strength.
direction.
Radial Rake Angle
Each Cutting Edge Angle in Face Milling
y STANDARD INSERTS
a Positive and Negative Rake Angle
Negative
Rake Angle
Neutral
Rake Angle
a Standard Cutting Edge Shape

Axial Rake Angle
Axial Rake Angle
Axial Rake Angle
Radial Rake Angle
Radial Rake Angle
Radial Rake Angle
Positive
Rake Angle
Standard Cutting
Edge Combinations
Insert shape whose cutting edge

precedes is a positive rake angle.
Insert shape whose cutting edge
follows is a negative rake angle.
Double Positive
(DP Edge Type)
Double Negative
(DN Edge Type)
Axial Rake Angle (A.R.)
Positive ( + )
Negative ( )
Positive ( + )
Radial Rake Angel (R.R.)
Positive ( + )
Negative ( )
Negative ( )
Positive Insert (One Sided Use) Negative Insert (Double Sided Use) Positive Insert (One Sided Use)
Insert Used
Work Material
Negative/Positive
(NP Edge Type)
Steel
Cast Iron
Aluminum Alloy
Difcult-to-Cut Material
y CORNER ANGLE (CH) AND CUTTING RESISTANCE

SE445 Type
545 Type
SE415 Type
515 Type
Corner Angle : 0 Corner Angle : 15 Corner Angle : 45

Principal
Force
Principal
Force
Feed Force
Principal
Force
Feed Force
Back Force
fz(IPT)
Corner Angle 0
Back Force
fz(IPT)
Corner Angle Corner angle 15 is recommended
15
Workpiece : Alloy Steel (281HB)

Tool : 4" Single Insert
Cutting Conditions : vc=410SFM ap=.157inch ae=4.33inch
Cutting Resistance Comparison between

Different Insert Shapes
Principal Force
direction. Lifts the workpiece when

workpiece clamp rigidity is low.
Feed Force
Back Force
fz(IPT)
Corner Angle Back force is in the minus
Back Force
for face milling of workpieces

with low rigidity such as thin
workpieces.
Corner Angle 15
Corner Angle The largest back force.
45
Bends thin workpieces and lowers

cutting accuracy.
Prevents workpiece edge
chipping in cast iron cutting.
Feed Force
Table Feed
Three Cutting Resistance Forces in Milling
TECHNICAL DATA
Cutting Resistance (N)
SE300 Type
400 Type
Corner Angle 45
force: Force is in the opposite direction of face milling rotation.

* Principal
force: Force that pushes in the axial direction.
* Back
* Feed Force: Force is in the feed direction and is caused by table feed.
N013
TECHNICAL DATA

FOR FACE MILLING
y CORNER ANGLE AND TOOL LIFE
a Corner Angle and Chip Thickness
When the depth of cut and feed per tooth, fz, are xed, the larger the corner angle (CH) is, then the thinner the chip thickness (h)
becomes (for a 45 CH, it is approx. 75 that of a 0 CH). This can be seen in below. Therefore as the CH increases, the cutting
resistance decreases resulting in longer tool life. Note however, if the chip thickness is too large then the cutting resistance can
increase leading to vibrations and shortened tool life.
Effects on chip thickness due to the variation of corner angles

a Corner Angle and Crater Wear
Below shows wear patterns for different corner angles. When comparing crater wear for 0 and 45 corner angles, it can be clearly
seen that the crater wear for 0 corner angle is larger. This is because if the chip thickness is relatively large, the cutting resistance
increases and so promotes crater wear. As the crater wear develops then cutting edge strength will reduce and lead to fracturing.
0 Corner Angle
15 Corner Angle
45 Corner Angle
vc=330SFM
Tc=69min
vc=410SFM
Tc=55min

Tool : D1=4.92inch
Insert : M20
Cutting Conditions : ap=.118inch
ae=4.33inch
fz=.008IPT
Coolant : Dry Cutting
vc=525SFM
Tc=31min
y UP CUT AND DOWN CUT MILLING

Which method to be used will depend on the machine and the face mill cutter that has been selected. Generally down cut machining
offers longer tool life than up cut milling.
TECHNICAL DATA
Up Cut Milling
Tool rotation
Workpiece
movement
direction
Tool rotation
Milling cutter inserts
Milling cutter inserts

Portion machined
N014
Down Cut Milling

Portion machined
Workpiece
movement
direction
y FINISHED SURFACE
a Cutting Edge Run-out Accuracy
Cutting edge run-out accuracy of indexable inserts on the cutter body

greatly affects the surface nish and tool life.
Minor Cutting Edge
Large
Peripheral
Cutting Edge
Chipping Due to Vibration

Shorten Tool Life
Poor Finished Surface

Rapid Wear Growth
Run-out
Small
Stable Tool Life
Good Finished Surface
Cutting Edge Run-out and

Accuracy in Face Milling
Table Feed
Cutting Edge No.
Feed per Tooth

Feed per Revolution
Sub Cutting Edge Run-out

and Finished Surface
Mitsubishi Materials' normal minor cutting edge wiper flat width is .055 inch. Usually the
minor cutting edges are set parallel to the face of a milling cutter and theoretically the
nished surface accuracy should be maintained, even if run-out accuracy is poor.
Actual Problems
Countermeasure
Cutting edge
run-out.
Minor cutting edge
inclination.
Cutter body
accuracy.
Spare parts
accuracy.
Welding, vibration,
chattering.
Wiper Insert
a surface
* Machine
that has already
been machined by
normal insert in
order to produce
smooth nished
surface.
.0012 .004inch
D.O.C
a Improve Finished Surface Roughness
Wiper Insert
Standard Insert
Replace one normal insert with wiper

insert.
Wiper inserts are set to protrude by
.0012 .004 inch from the standard
inserts.
a How to Set a Wiper Insert
Body
Locator
Body
Locator
(a) One Corner Type
(b) Two Corner Type
Replace normal insert.
Replace normal insert.
Locator
(c) Two Corner Type

Use locator for
wiper insert.
TECHNICAL DATA
Body
Minor cutting edge length has to be larger than

the feed per revolution.
But, too long minor cutting edge can also
cause chattering.
When the cutter diameter is large and feed per
revolution is longer than the minor cutting
edge of the wiper insert, the use of two or
three wiper inserts is possible.
When using more than 1 wiper inserts,
eliminate run-out of wiper inserts.
Use a high hardness grade (high wear
resistance) for wiper inserts.
N015
TECHNICAL DATA
FORMULAS FOR MILLING

vc = ) D1 n (SFM)
12
vc (SFM)
) (3.14)
: Cutting Speed
: Pi
(Problem)
(Answer)
D1 (inch) : Cutter Diameter

n (min-1) : Main Axis Spindle Speed
What is the cutting speed when main axis spindle speed is 350min-1
and cutter diameter is & 5" ?
Substitute ) 3.14, D = 5", n= 350 into the formula.
vc = ) D n = 3.14 x 5" x 350 = 457.9 SFM
12
12
The cutting speed is 457.9SFM.
y FEED PER TOOTH (fz)
fz =
vf
(IPT)
zn
z : Insert Number
fz (IPT)
: Feed per Tooth
vf (inch/min) : Table Feed per Min.
n (min-1)
: Main Axis Spindle Speed (Feed per Revolution fr = z x fz)
(Problem)
Feed
Direction
Feed per Tooth
(Answer)
What is the feed per tooth when the main axis spindle speed is
500min-1, insert number is 10, and table feed is 20inch/min ?
Substitute the above figures into the formula.
20
= .004 IPT
fz = Vf =
zxn
10 x 500
The answer is .004IPT.
Wiper Edge Angle

Tooth Mark
y TABLE FEED (vf)
vf = fz z n (inch/min)

fz (IPT)
: Feed per Tooth
z : Insert Number
n (min-1)
(Problem)
(Answer)
What is the table feed when feed per tooth is .004IPT, with 10 inserts
and main axis spindle speed is 500min-1?
Substitute the above figures into the formula.
vf = fz x z x n = .004IPT x 10 x 500 = 20inch/min
The table feed is 20inch/min.
y CUTTING TIME (Tc)
TECHNICAL DATA
Tc =
L
vf
(min)
Tc (min)
: Cutting Time
L (inch)
: Total Table Feed Length (Workpiece Length(l )+ Cutter Diameter(D1))
(Problem)
(Answer)
What is the cutting time required for finishing 4" width and 12" length
surface of a cast iron (GG20) block when cutter diameter is & 8", the
number of inserts is 16, the cutting speed is 410SFM, and feed per tooth is
.01". (spindle speed is 200min-1)
Calculate table feed per min vf=.01 x 16 x 200=32inch/min
Calculate total table feed length. L=12+8=20inch
Substitute the above answers into the formula.
Tc = 20 = 0.625 (min)
32
0.625 x 60 = 37.5 (sec.)
N016
The answer is 37.5 sec.
TROUBLE SHOOTING FOR END MILLING
Machine Stability, Rigidity
Increase Chuck Clamping Power
Spindle Collet Run-out Accuracy
Tool Installation Accuracy
Wider Chip Pocket
Tool Diameter
Concavity Angle of
End Cutting Edge
Number of Flutes
Improve End Mill Rigidity
Air Blow
Increase Coolant
Quantity
Determine Dry or
Wet Cutting
Down
Cut
Improper cutting
conditions
Fragile cutting edge
Insufcient clamping
force
Poor clamping
rigidity
Improper cutting
conditions
Poor end mill rigidity
Overhang longer
than necessary
Poor wall
surface
roughness
a
a
Chip packing
a
a
a
a
a
Wet
a
a
a
a
a
a
Poor surface Improper cutting

conditions
nish
Poor clamping
accuracy
rigidity
Improper cutting
Burr,
conditions
workpiece
Large helix angle
chipping
Improper cutting
conditions
Metal removal
too large
Lack of ute
chip space
Notch wear occurs
Chip jamming
Quick burr
formation
Poor bottom The end cutting edge does

not have a concave angle
surface
Large pick feed
roughness
Large cutting
edge wear
Out of
Improper cutting
conditions
vertical
Improper cutting
conditions
Poor clamping
rigidity
Large cutting
edge wear
Improper cutting
conditions
Chip packing
Vibration
during
cutting
a
a
a
a
a
a
TECHNICAL DATA
Chipping
Breakage
during
cutting
Poor Surface Finish
Down
Up cut milling
Chip Control Burr / Chipping / Burrs
Up
Large wear
Not enough utes
at the peripheral
Improper cutting
cutting edge
conditions
Short Tool Life
Down Cut
Depth of Cut
Feed Rate
Cutting Speed
Down
Cutting
Fluids
Machine and
Collet Inspection and Exchange
Non-coated insert
is used
Up
Decrease Pick Feed Rate
s
or
ct
Fa
Trouble
Coated Tool
Solutions
Style and Design

of the Tool
Cutting Conditions
Helix Angle
Insert Grade
Selection
a
a
N017
TECHNICAL DATA
END MILL FEATURES AND SPECIFICATION

y NOMENCLATURE
Cutter sweep
Neck
Body (Cutting part)
Shank (Handle)
Shank diameter
Diameter
Length of cut
Overall length
Corner
Land width
Concavity angle of end cutting edge
End cutting edge
Peripheral cutting edge
Relief width (Flank width)

End gash
Radial primary relief angle
Axial rake angle
Radial secondary
clearance angle
Helix angle
Radial rake angle
Axial primary relief angle
Axial secondary clearance angle
y COMPARISON OF SECTIONAL AREA OF CHIP POCKET
2-utes
50%
3-utes
45%
4-utes
40%
6-utes
20%
N018
4-utes
6-utes
Advantage
3-utes
Effective chip disposal.

Horizontal feed milling
possible.
Effective chip disposal.

Horizontal feed milling
possible.
High rigidity.
High rigidity.
Superior cutting
edge durability.
Fault
Feature
2-utes
Low rigidity.
Diameter is not
measured easily.
Chip disposal is poor.
Chip disposal is poor.
Various cutting modes

including slotting, shoulder
milling and drilling.
Slotting, shoulder milling

Heavy cutting, nishing
Shallow slotting, shoulder

milling Finishing
Machining hardened steels.

Shallow slotting, shoulder
milling.
Usage
TECHNICAL DATA
y CHARACTERISTICS AND APPLICATIONS OF DIFFERENT-NUMBER-OF-FLUTE END MILLS
END MILL TYPE AND GEOMETRY

y PERIPHERAL CUTTING EDGE
Type
Shape
Feature
Regular ute geometry as shown is most commonly used for roughing
and nishing of side milling, slotting and shoulder milling.
Ordinary Flute
Tapered Flute
A tapered ute geometry is used for special applications such as

mould drafts and for applying taper angles after conventional straight
edged milling.
Roughing Flute
Roughing type geometry has a wave like edge form and breaks the
material into small chips. Additionally the cutting resistance is low
enabling high feed rates when roughing. The inside face of the ute is
suitable for regrinding.
Formed Flute
Special form geometry as shown is used for producing corner radii on

components. There are an innite number of different geometry's that can
be manufactured using such style of cutters.
y END CUTTING EDGE

Type
Shape
Feature
Square End
(With Center Hole)
Generally used for side milling, slotting and shoulder milling. Plunge
cutting is not possible due to the center hole that is used to ensure
accurate grinding and regrinding of the tool.
Square End
(Center Cut)
Generally used for side milling, slotting and shoulder milling. Plunge
cutting is possible and greater plunge cutting efciency is obtained
when using fewer utes. Regrinding on the ank face can be done.
Ball End
Geometry completely suited for curved surface milling. At the extreme

end point the chip pocket is very small leading to inefcient chip
evacuation.
Corner Radius End
Used for radius proling and corner radius milling. When pick feed
milling an end mill with a large diameter and small corner radius can
be efciently used.
y SHANK AND NECK PARTS
Standard
(Straight Shank)
Long Shank
Shape
Feature
Most widely used type.
Long shank type for deep pocket and shoulder applications.
Long Neck
Long neck geometry can be used for deep slotting and is also suitable
for boring.
Taper Neck
Long taper neck features are best utilized on deep slotting and mould
draft applications.
TECHNICAL DATA
Type
N019
TECHNICAL DATA
PITCH SELECTION OF PICK FEED

y PICK FEED MILLING (CONTOURING) WITH BALL NOSE END MILLS, END MILLS WITH CORNER RADIUS
End mill
sin-1
h=R 1 cos
R : Radius of Ball Nose, Corner Radius

P : Pick Feed
h : Cusp Height
y CORNER R OF END MILLS AND CUSP HEIGHT BY PICK FEED

P
Pitch of Pick Feed (P)

.004
.008
.012
.016
.020
.024
.028
.031
.035
.039
0.5
.0001
.0004
.0009
.0017
.0026
.0039
.00004
.0002
.0004
.0008
.0016
.0018
.0025
.0033
.0042
1.5
.00004
.0001
.0003
.0005
.0008
.0012
.0016
.0021
.0027
.0034
.00004
.0001
.0002
.0004
.0006
.0009
.0012
.0016
.0020
.0025
2.5
.00004
.00007
.0002
.0003
.0005
.0007
.0010
.0013
.0016
.0020
.00007
.0002
.0003
.0004
.0006
.0008
.0011
.0013
.0017
.00004
.0001
.0002
.0003
.0004
.0006
.0008
.0010
.0012
.00004
.00007
.0002
.0002
.0004
.0005
.0006
.0008
.0010
.00004
.00007
.0001
.0002
.0003
.0004
.0005
.0007
.0008
.00004
.0001
.0002
.0002
.0003
.0004
.0005
.0006
10
.00004
.00007
.0001
.0002
.0002
.0003
.0004
.0005
12.5
.00004
.00007
.0001
.0002
.0002
.0002
.0003
.0004
TECHNICAL DATA
Pitch of Pick Feed (P)

.043
.047
.051
.055
.059
.063
.067
.071
.075
.079
0.5
1.5
.0041
.0030
.0036
.0043
2.5
.0024
.0029
.0034
.0039
.0020
.0024
.0028
.0033
.0037
.0043
.0015
.0018
.0021
.0024
.0028
.0032
.0036
.0041
.0012
.0014
.0017
.0019
.0022
.0025
.0029
.0032
.0036
.0040
.0010
.0012
.0014
.0016
.0019
.0021
.0024
.0027
.0030
.0033
.0007
.0009
.0010
.0012
.0014
.0016
.0018
.0020
.0022
.0025
10
.0006
.0007
.0008
.0010
.0011
.0013
.0014
.0016
.0018
.0020
12.5
.0005
.0006
.0007
.0008
.0009
.0010
.0011
.0013
.0014
.0016
N020
Unit : inch
TROUBLE SHOOTING FOR DRILLING

Machine Stability, Rigidity
Workpiece Installation Accuracy
Flatten the Workpiece Face
Tool Installation Accuracy
Change to a Drill with

X Type Thinning
Small
Use a Drill with Coolant Holes
Large
Decrease the Lip Height
Shorten the Flute Length
Chisel Width
Increase Coolant
Pressure
Increase Volume
Increase Oil Ratio
Increase the Accuracy and

the Depth of the Pre-hole
Feed Rate
Core Thickness
Lack of drill
rigidity
Improper cutting
conditions
Drill breakage
Large deection
of the tool holder
Workpiece face
is inclined
Improper cutting
conditions
Large wear
Increase in tem.
at the peripheral at cutting point
cutting edge
Poor run-out
accuracy
lmproper cutting
conditions
Chipping of
Large deection
the peripheral of the tool holder
cutting edge
Chattering,
vibration
The chisel edge
width is too large
Chisel edge
Poor entry
chipping
Chattering,
vibration
Lack of drill
Hole diameter rigidity
Improper drill
increases
geometry
Increase in tem.
at cutting point
Hole diameter
Improper cutting
becomes
conditions
smaller
Improper drill
geometry
Lack of drill
rigidity
Poor
Large deection
straightness of the tool holder
Poor guiding
properties
Lack of drill
rigidity
Poor hole
positioning
Poor entry
accuracy,
Improper cutting
roundness and conditions
surface nish Large deection
of the tool holder
Improper drill
Burrs at the geometry
Improper cutting
hole exit
conditions
Improper cutting
conditions
Long chips
Poor chip
disposal
Improper cutting
conditions
Chip packing
Poor chip
disposal
Down
Step Feed
Lower the Feed when Exiting
or
Cutting
Fluids
Machine and
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
TECHNICAL DATA
Short Tool Life

Poor Hole Accuracy
Burr
Chip Control
Up
ct
Lower the Feed at Initial Entry
Fa
Trouble
Cutting Speed
Solutions
Honing Width
Style and Design

of the Tool
Cutting Conditions
N021
TECHNICAL DATA
DRILL WEAR CONDITION

AND CUTTING EDGE DAMAGE
y DRILL WEAR CONDITION
The diagram below shows a simple drawing depicting the wear of a drill's cutting edge. The generation and the amount of wear differ
according to the workpiece materials and cutting conditions used. But generally, the peripheral wear is largest and determines a drill
tool life. When regrinding, the ank wear at the point needs to be ground away completely. Therefore, if there is large wear more
material needs to be ground away to renew the cutting edge.
We : Chisel edge wear width
Wf
Wf
: Flank wear width (The middle of the cutting edge)
Wo : Outer corner wear width

Wm : Margin wear width
Wo
Wm
Wm'
Wm' : Margin wear width (Leading edge)
y CUTTING EDGE DAMAGE

When drilling, the cutting edge of the drill can suffer from chipping, fracture and abnormal damage. In such cases it is important to
take a closer look at the damage, investigate the cause and take countermeasures.
b
a
TECHNICAL DATA
N022
DRILL TERMINOLOGY
AND CUTTING CHARACTERISTICS
y NAMES OF EACH PART OF A DRILL
Height of point
Straight shank with tang
Clearance angle
Body
Lead
Flank
Neck
Taper shank
Tang
Helix angle
Drill
diameter
Outer corner
Axis
Point angle
Neck
length
Flute length
Shank length
Overall length
Margin width
Depth of body clearance

Body clearance
Margin
Flute
Flute width
Chisel edge angle
Cutting edge
Land width
y SHAPE SPECIFICATION AND CUTTING CHARACTERISTICS
High-hardness material Small
Rake Angle
Large
Soft material (Aluminum, etc.)
Flute Length
It is determined by depth of hole, guide bush length, and regrinding allowance. Since the inuence on the tool life
is great, it is necessary to minimize it as much as possible.
Point Angle
In general, the angle is 118 for high speed steel drills and 130 140 for carbide drills.
Point angle
Soft material with good machinability Small
Large For hard material and
high-efciency machining
Web Thickness
It is an important element that determines the rigidity and chip disposal performance of a drill. The web thickness
is set according to applications.
Large cutting resistance
Low cutting resistance
High rigidity
Low rigidity
Thin
Web thickness
Thick
Poor chip disposal
Good chip disposal performance
High-hardness material,
Machinable material
cross hole drilling, etc.
Margin
The margin determines the drill diameter and functions as a drill guide during drilling. The margin width is decided
taking into consideration the friction with in the hole to be drilled.
Poor guiding performance Small
Diameter
Back Taper
Margin width
Large
Good guiding performance
TECHNICAL DATA
Helix Angle
Is the inclination of the ute with respect to the axial direction of a drill, which corresponds to the rake angle. The rake
angle of a drill differs according to the position along the cutting edge. The rake angle is largest at the periphery and
smallest towards the center of the cutting edge. The chisel edge has a negative rake angle, crushing the work.
To reduce friction with the inside of the drilled hole, the portion from the point to the shank is tapered slightly. The
degree is usually represented by the quantity of reduction in the diameter with respect to the ute length, which is
approx. .0016" .016"/4".
N023
TECHNICAL DATA
DRILL TERMINOLOGY
AND CUTTING CHARACTERISTICS
y CUTTING EDGE GEOMETRY AND ITS INFLUENCE
As shown in table below, it is possible to select the most suitable cutting edge geometry for different applications. If the most
suitable cutting edge geometry is selected then higher machining efciency and higher hole accuracy can be obtained.
a Typical Cutting Edge Geometries
Grinding Name
Geometry
Features and Effect
Use
The ank is conical and the clearance angle

increases toward the center of the drill.
For general use.
The ank is at and facilitates cutting.
Mainly for small diameter

drills.
As there is no chisel edge, the results are high

centripetal force and small hole oversize.
Requires a special grinding machine.
Requires grinding of three sides.
For drilling operations

that require high hole
accuracy and positioning
accuracy.
For drilling that requires
high accuracy.
Spiral Point
To increase the clearance angle near the center

of the drill, conical grinding combined with
irregular helix.
S type chisel edge with high centripetal force and
machining accuracy.
Radial Lip
The cutting edge is ground radial with the aim of dispersing

load.
High machining accuracy and nished surface roughness.
For through holes, small burrs on the base.
Requires a special grinding machine.
For cast iron and light

alloy.
For cast iron plates.
Steel
This geometry has two-stage point angle for

better concentricity and a reduction in shock
when exiting the workpiece.
For thin sheet drilling.
Conical
Flat
Three Rake
Angles
Center Point
Drill
y WEB THINNING
TECHNICAL DATA
The rake angle of the cutting edge of a drill reduces toward the center, and it changes into a negative angle at the chisel edge. During
drilling, the center of a drill crushes the work, generating 50 70% of the cutting resistance. Web thinning is very effective for reduction in
the cutting resistance of a drill, early removal of cut chips at the chisel edge, and better initial bite.
Geometry
X type
Features
The thrust load substantially

reduces, and the bite
performance improves. This
is effective when the web is
thick.
Major
General drilling and deep hole
Applications drilling.
N024
XR type
S type
N type
The initial performance is

slightly inferior to that of the X
type, but the cutting edge is
tough and the applicable range
of workpiece materials is wide.
Popular design, easy cutting

type.
Effective when the web is

comparatively thick.
General drilling and stainless

steel drilling.
General drilling for steel, cast

iron, and non-ferrous metal.
Deep hole drilling.
y DRILLING CHIPS
Types of Chips
Conical Spiral
Geometry
Features and Ease of Raking
Fan-shaped chips cut by the cutting edge are curved by the ute. Chips of this type
are produced when the feeding rate of ductile material is small. If the chip breaks
after several turns, the chip raking performance is satisfactory.
Long pitch chips exit without coiling and will coil around the drill.
Long Pitch
Segment
Zigzag
Needle
This is a chip broken by the restraint caused by the drill ute and the wall of a drilled
hole. It is generated when the feed rate is high.
A conical spiral chip that is broken before the chip grows into the long-pitch shape by
the restraint caused by the wall of the drilled hole due to the insufciency of ductility.
Excellent chip disposal and chip discharge.
A chip that is buckled and folded because of the shape of ute and the characteristics
of the material. It easily causes chip packing in the ute.
Chips broken by vibration or broken when brittle material is curled with a small radius.
The raking performance is satisfactory, but these chips can become closely packed
jams.
TECHNICAL DATA
Fan
N025
TECHNICAL DATA
FORMULAS FOR DRILLING

(SFM)
*Unit transformation (fromn "mm" to "m")
vc (SFM)
) (3.14)
: Cutting Speed
: Circular Constant
D1(inch) : Drill Diameter

n (min-1) : Rotational Speed of the Main Spindle
(Problem) What is the cutting speed when main axis spindle speed is 1350min-1
and drill diameter is .500inch ?
(Answer) Substitute )=3.14, D1=.500inch, n=1350 into the formula
vc =
= 176.6SFM
The cutting speed is 176.6SFM
D1
y FEED OF THE MAIN SPINDLE (vf)
(inch/min)
vf
vf (inch/min) : Feed Speed of the Main Spindle (Z axis)

fr (IPR)
n (min-1)
: Rotational Speed of the Main Spindle
(Problem) What is the spindle feed (v f) when feed per revolution is .008IPR and
main axis spindle speed is 1350min-1?
(Answer) Substitute fr=.008, n=1350 into the formula
vf = frn = .0081350 = 10.8inch/min
The spindle feed is 10.8inch/min.
fr
y DRILLING TIME (Tc)

Tc
n
ld
fr
i
(min)
(min-1)
(inch)
(IPR)
TECHNICAL DATA
ld
N026
: Drilling Time
: Spindle Speed
: Hole Depth
: Number of Holes
(Problem) What is the drilling time required for drilling a 1.2inch

length hole in alloy steel at a cutting speed of 165SFM
and feed .006IPR ?
(Answer) Spindle Speed
TOOL WEAR AND DAMAGE

CAUSES AND COUNTERMEASURES
Tool Damage Form
Cause
Countermeasure
Tool grade is too soft.

Cutting speed is too high.
Flank angle is too small.
Feed rate is extremely low.
Tool grade with high wear resistance.

Lower cutting speed.
Increase ank angle.
Increase feed rate.
Crater Wear

Feed rate is too high.

Lower feed rate.
Chipping
Tool grade is too hard.

Lack of cutting edge strength.
Tool grade with high toughness.

Lower feed rate.
Increase honing. (Round honing is to be
changed to chamfer honing.)
Use large shank size.
Flank Wear
Lack of shank or holder rigidity.
Fracture
Plastic
Deformation
Welding
Lack of shank or holder rigidity.

Lower feed rate.
Increase honing. (Round honing is to be
changed to chamfer honing.)
Use large shank size.

Depth of cut and feed rate are too large.
Cutting temperature is high.

Decrease depth of cut and feed rate.
Tool grade with high thermal conductivity.
Cutting speed is low.
Increase cutting speed. (For ANSI 1045,

cutting speed 260 SFM.)
Increase rake angle.
Tool grade with low afnity.
(Coated grade, cermet grade)

Lack of cutting edge strength.
Poor sharpness.
Unsuitable grade.
Expansion or shrinkage due to cutting
heat.
Thermal Cracks
Especially in milling.
*
Notching
Dry cutting.
(For wet cutting, ood workpiece with
cutting uid)
Hard surfaces such as uncut surface,

chilled parts and machining hardened
layer.
Friction caused by jagged shape chips.
(Caused by small vibration)
Cutting edge welding and adhesion.

Poor chip disposal.
Increase rake angle to improve sharpness.

Enlarge chip pocket.
Damage due to the lack of strength of

a curved cutting edge.
Increase honing.

Cutting resistance is too high and
causes high cutting heat.
Decrease honing.
Increase rake angle to improve

sharpness.
Flank Wear
Fracture
for
*Damage
polycrystallines
Crater Wear
Fracture
TECHNICAL DATA
Flaking
for
*Damage
polycrystallines
N027
TECHNICAL DATA
MATERIAL CROSS REFERENCE LIST

y CARBON STEEL
USA
AISI/SAE
Japan
JIS
Germany
W.-nr.
DIN
U. K.
BS
EN
France
AFNOR
Italy
UNI
Spain
UNE
Sweden
SS
China
GB
RSt.37-2
4360 40 C
E 24-2 Ne
1311
15
1015
1020
STKM 12A
1.0038
STKM 12C
1.0401
1.0402
C15
C22
080M15
050A20
2C
CC12
CC20
C15, C16
C20, C21
15
20
1213
SUM22
1.0715
9SMn28
230M07
1A
S250
CF9SMn28
12L13
1215
12L14
1015
1025
A572-60
1035
1045
1140
1039
1335
1330
1035
1045
1050
1055
1060
1055
1060
1095
W1
W210
SUM22L
S15C
S25C
SMn438(H)
SCMn1
S35C
S45C
S50C
S55C
S58C
SK3
SUP4
1.0718
1.0722
1.0736
1.0737
1.1141
1.1158
1.8900
1.0501
1.0503
1.0726
1.1157
1.1167
1.1170
1.1183
1.1191
1.1213
1.0535
1.0601
1.1203
1.1221
1.1274
1.1545
1.1545
9SMnPb28
10SPb20
9SMn36
9SMnPb36
Ck15
Ck25
StE380
C35
C45
35S20
40Mn4
36Mn5
28Mn6
Cf35
Ck45
Cf53
C55
C60
Ck55
Ck60
Ck101
C105W1
C105W1
240M07
080M15
4360 55 E
060A35
080M46
212M36
150M36
150M28
060A35
080M46
060A52
070M55
080A62
070M55
080A62
060A96
BW1A
BW2
1B
32C
8M
15
14A
9
43D
43D
S250Pb
10PbF2
S300
S300Pb
XC12
CC35
CC45
35MF4
35M5
40M5
20M5
XC38TS
XC42
XC48TS
CC55
XC55
XC60
XC100
Y105
Y120
CF9SMnPb28
CF10Pb20
CF9SMn36
CF9SMnPb36
C16
FeE390KG
C35
C45
C28Mn
C36
C45
C53
C55
C60
C50
C60
C36KU
C120KU
F.111
1350
F.112
1450
F.2111
1912
11SMn28
11SMnPb28 1914
10SPb20
12SMn35
12SMnP35 1926
C15K
1370
2145
F.113
1550
F.114
1650
F210G
1957
36Mn5
2120
1572
C45K
1672
1674
1655
C55K
1678
F.5117
1870
F.5118
1880
F.515
2900
A570.36
Y15
Y13
15
25
35
45
40Mn
35Mn2
30Mn
35Mn
Ck45
50
55
60
55
60Mn
y ALLOY STEEL
USA
AISI/SAE
A573-81
TECHNICAL DATA
N028
5120
9255
9262
ASTM 52100
ASTM A204Gr.A
4520
ASTM A350LF5
ASTM A353
3135
3415
3415, 3310
8620
8740
5015
Japan
JIS
Germany
W.-nr.
DIN
SM400A, SM400B
1.0144
SM400C
SM490A, SM490B
1.0570
SM490C
1.0841
1.0904
1.0961
SUJ2
1.3505
1.5415
1.5423
1.5622
1.5662
SNC236
1.5710
SNC415(H) 1.5732
SNC815(H) 1.5752
SNCM220(H) 1.6523
SNCM240 1.6546
1.6587
SCr415(H) 1.7015
U. K.
BS
EN
France
AFNOR
St.44.2
4360 43 C
E28-3
St52-3
4360 50 B
E36-3
St52-3
55Si7
60SiCr7
100Cr6
15Mo3
16Mo5
14Ni6
X8Ni9
36NiCr6
14NiCr10
14NiCr14
21NiCrMo2
40NiCrMo22
17CrNiMo6
15Cr3
150M19
250A53
45
534A99
31
1501-240
1503-245-420
1501-509-510
640A35
111A
655M13
36A
805M20
362
311-Type 7
820A16
523M15
20MC5
55S7
60SC7
100C6
15D3
16N6
35NC6
14NC11
12NC15
20NCD2
18NCD6
12C3
Italy
UNI
Fe52BFN
Fe52CFN
Fe52
55Si8
60SiCr8
100Cr6
16Mo3KW
16Mo5
14Ni6
X10Ni9
16NiCr11
20NiCrMo2
40NiCrMo2(KB)
Spain
UNE
Sweden
SS
China
GB
1412
2132
F.431
56Si7
60SiCr8
F.131
16Mo3
16Mo5
15Ni6
XBNi09
15NiCr11
20NiCrMo2
40NiCrMo2
14NiCrMo13
2172
2085
2258
2912
2506
55Si2Mn
Gr15, 45G
15Cr
Japan
JIS
5140
5155
ASTM A182
F11, F12
ASTM A182
F.22
9840
4340
5132
5140
5115
4130
SCr440
SUP9(A)
SCM415(H)
1.7045
1.7176
1.7262
1.7335
1.7380
SCr430(H)
SCr440(H)
SCM420
SCM430
SCM432
SCCRM3
1.7715
1.8523
1.6511
1.6582
1.7033
1.7035
1.7131
1.7218
1.7220
34CrMo4
708A37
SCM 440
1.7223
41CrMo4
4140
SCM440(H) 1.7225
42CrMo4
6150
SUP10
4137
4135
4140
4142
L3
Germany
W.-nr.
DIN
Italy
UNI
Spain
UNE
55C3
12CD4
15CD3.5
15CD4.5
12CD9
12CD10
40NCD3
35NCD6
32C4
42C4
16MC5
25CD4
14CrMo45
42Cr4
12CrMo4
14CrMo45
2245
2216
40Cr
20CrMn
TU.H
2218
13MoCrV6
35NiCrMo4
35Cr4
42Cr4
16MnCr5
2541
2511
2225
40CrNiMoA
35Cr
40Cr
18CrMn
19B
35CD4
35CrMo4
34CrMo4
2234
35CrMo
708M40
19A
42CD4TS
41CrMo4
42CrMo4
2244
40CrMoA
708M40
19A
42CD4
42CrMo4
42CrMo4
2244
1.7361
1.8159
32CrMo12 722M24
50CrV4
735A50
40B
47
32CrMo12 F.124.A
50CrV4
51CrV4
1.8509
41CrAlMo7 905M39
41B
100Cr6
105WCr6
BL3
30CD12
50CV4
40CAD6
40CAD2
Y100C6
105WC13
55NiCrMoV6
X8Ni9
12Ni19
14NiCrMo134
X210Cr12
BH224/5
1501-509
832M13
BD3
36C
55NCDV7
Z18N5
Z200C12
Z40CDV5
52
Z100CDV5
Z30WCV9
Y1105V
Z80WKCV
Z80WCV
Z120M12
Z45CS9
Z40CSD10
Z85WDCV
6-5-2-5
1.2067
SKS31
1.2419
SKS2, SKS3
L6
SKT4
1.2713
ASTM A353
1.5662
2515
1.5680
1.6657
D3
SKD1
1.2080
ASTM D3
H13
SKD61
1.2344
ASTM H13
A2
SKD12
1.2363
SKD2
1.2436
S1
1.2542
H21
SKD5
1.2581
1.2601
W210
SKS43
1.2833
T4
SKH3
1.3255
T1
SKH2
1.3355
SCMnH/1 1.3401
HW3
SUH1
1.4718
D3
SUH3
1.3343
SKH9, SKH51 1.3343
M2
M7
1.3348
M35
SKH55
1.3243
42Cr4
55Cr3
15CrMo5
13CrMo4 4
U. K.
BS
EN
527A60
48
1501-620Gr27
1501-622
Gr31, 45
14MoV63 1503-660-440
39CrMoV13 9 897M39
40C
36CrNiMo4 816M40
110
34CrNiMo6 817M40
24
34Cr4
530A32
18B
41Cr4
530M40
18
16MnCr5 (527M20)
25CrMo4 1717CDS110
708M20
10CrMo910
X40CrMoV51 BH13
X40CrMoV51
X100CrMoV51 BA2
X210CrW12
45WCrV7 BS1
X30WCrV93 BH21
X165CrMoV12
100V1
BW2
S 18-1-2-5 BT4
S 18-0-1
BT1
G-X120Mn12 Z120M12
X45CrSi93 401S45
S6-5-2
4959BA2
S6/5/2
BM2
S 2-9-2
S6/5/2/5
BM35
France
AFNOR
12CrMo9
12CrMo10
36CrMoV12
38NiCrMo4(KB)
35NiCrMo6(KB)
34Cr4(KB)
41Cr4
16MnCr5
25CrMo4(KB)
55Cr3
Sweden
SS
2240
2230
China
GB
30CrMn
42CrMo
42CrMnMo
50CrVA
41CrAlMo7 41CrAlMo7 2940
100Cr6
100WCr6
105WCr5 2140
107WCr5KU
F.520.S
X10Ni9
XBNi09
15NiCrMo13 14NiCrMo131
X210Cr13KU X210Cr12
X250Cr12KU
X35CrMoV05KU X40CrMoV5 2242
X40CrMoV51KU
X100CrMoV51KU X100CrMoV5 2260
X215CrW121KU X210CrW12 2312
45WCrV8KU 45WCrSi8 2710
X28W09KU X30WCrV9
X165CrMoW12KU X160CrMoV12 2310
X78WCo1805KU HS18-1-1-5
X75W18KU HS18-0-1
XG120Mn12 X120MN12
X45CrSi8 F.322
15NiCrMo13
2715
HS6-5-2-2 F.5603
2722
HS2-9-2
HS2-9-2
2782
HS6-5-2-5 F.5613
2723
CrV, 9SiCr
CrWMo
5CrNiMo
Cr12
40CrMoV5
100CrMoV5
30WCrV9
V
W18Cr4VCo5
X45CrSi93
TECHNICAL DATA
USA
AISI/SAE
N029
TECHNICAL DATA
MATERIAL CROSS REFERENCE LIST

y STAINLESS STEEL (FERRITIC, MARTENSITIC)
USA
AISI/SAE
Japan
JIS
Germany
W.-nr.
DIN
U. K.
BS
EN
France
AFNOR
Italy
UNI
Spain
UNE
Sweden
SS
China
GB
403
SUS403
1.4000
X7Cr13
403S17
Z6C13
F.3110
2301
416
410
430
SUS416
SUS410
SUS430
SCS2
SUS420J2
1.4001
1.4005
1.4006
1.4016
1.4027
1.4034
X7Cr14
X12CrS13
X10Cr13
X8Cr17
G-X20Cr14
X46Cr13
416S21
410S21
430S15
420C29
420S45
56A
60
56B
56D
2380
2302
2320
2304
SUS431
SUS430F
SUS434
SCS5
SUS405
SUS430
SUH4
SUH446
SUH35
1.4003
1.4021
1.4057
1.4104
1.4113
1.4313
1.4724
1.4742
1.4747
1.4762
1.4871
1.4521
1.4922
1.4542
405S17
420S37
X22CrNi17 431S29
X12CrMoS17
X6CrMo17 434S17
X5CrNi134 425C11
X10CrA113 403S17
X10CrA118 430S15
X80CrNiSi20 443S65
X10CrA124
X53CrMnNiN219 349S54
X1CrMoTi182
X20CrMoV12-1
F.8401
Z11CF13 X12CrS13 F.3411
Z10C14
X12Cr13 F.3401
Z8C17
X8Cr17
F.3113
Z20C13M
Z40CM
X40Cr14 F.3405
Z38C13M
Z8CA12
X6CrAl13
Z8CA12
X20Cr13
Z15CNi6.02 X16CrNi16 F.3427
Z10CF17 X10CrS17 F.3117
Z8CD17.01 X8CrMo17
Z4CND13.4M (G)X6CrNi304
Z10C13
X10CrA112 F.311
Z10CAS18 X8Cr17
F.3113
Z80CSN20.02 X80CrSiNi20 F.320B
Z10CAS24 X16Cr26
Z52CMN21.09 X53CrMnNiN219
X20CrMoNi1201
Z7CNU17-04
OCr13
1Cr12
1Cr13
1Cr17
4Cr13
2303
2321
2383
2325
2385
2322
2326
2317
1Cr17Ni2
Y1Cr17
1Cr17Mo
OCr13Al
Cr17
2Cr25N
5Cr2Mn9Ni4N
405
420
431
430F
434
CA6-NM
405
430
HNV6
446
EV8
S44400
630
57
60
59
X6Cr13
y STAINLESS STEEL (AUSTENITIC)
TECHNICAL DATA
USA
AISI/SAE
N030
Japan
JIS
Germany
W.-nr.
DIN
U. K.
BS
EN
France
AFNOR
Italy
UNI
Spain
UNE
Z2CN18.10 X2CrNi18.11
Z6CN18.09 X5CrNi1810 F.3551
F.3541
F.3504
Z10CNF18.09 X10CrNiS18.09 F.3508
Z3CN19.10
Z2CrNi1810 X2CrNi18.11 F.3503
Z12CN17.07 X12CrNi1707 F.3517
Z2CN18.10
Z6CND17.11 X5CrNiMo1712 F.3543
Z6CN18.10M
F.8414
Z4CNDNb1812M XG8CrNiMo1811
Z2CND17.13
Z2CND17.12 X2CrNiMo1712
Sweden
SS
China
GB
304L
304
SUS304L
SUS304
1.4306
1.4350
X2CrNi1911 304S11
X5CrNi189 304S11
58E
303
304L
301
304LN
316
316LN
316L
316L
SUS303
SUS304L
SCS19
SUS301
SUS304LN
SUS316
SCS13
SCS14
SCS22
SUS316LN
SCS16
SUS316L
SUS317L
1.4305
1.4306
1.4310
1.4311
1.4401
1.4308
1.4408
1.4581
1.4429
1.4404
1.4435
X12CrNiS188 303S21
304C12
X2CrNi189 304S12
X12CrNi177
X2CrNiN1810 304S62
X5CrNiMo1810 316S16
G-X6CrNi189 304C15
G-X6CrNiMo1810 316C16
G-X5CrNiMoNb1810 318C17
X2CrNiMoN1813
316S13
316S13
X2CrNiMo1812
58M
58J
1.4436
1.4438
1.4539
316S13
X2CrNiMo1816 317S12
Z6CND18-12-03 X8CrNiMo1713
Z6CNT18.10
2343, 2347
2367
OOCr19Ni13Mo
2562
SUS321
1.4541
321S12
58B
2337
347
SUS347
1.4550
347S17
58F
316Ti
318
1.4571
1.4583
X10CrNiMoTi1810 320S17
X10CrNiMoNb1812
58J
Z6CNT18.10 X6CrNiTi1811 F.3553

F.3523
Z6CNNb18.10 X6CrNiNb1811 F.3552
F.3524
Z6CNDT17.12 X6CrNiMoTi1712 F.3535
Z6CNDNb1713B X6CrNiMoNb1713
316
317L
UNS V
0890A
321
X1NiCrMo
X10CrNiTi189
X10CrNiNb189
2352
2332
OCr19Ni10
OCr18Ni9
2346
2333
2352
2331
2371
2347
2375
2348
2353
1Cr18Ni9MoZr
Cr17Ni7
0Cr17Ni11Mo2
OCr17Ni13Mo
OCr27Ni12Mo3
2338
2350
1Cr18NI9Ti
1Cr18Ni11Nb
Cr18Ni12Mo2T
Cr17Ni12Mo3Mb
USA
AISI/SAE
Japan
JIS
Germany
W.-nr.
DIN
U. K.
BS
EN
France
AFNOR
Italy
UNI
Spain
UNE
Sweden
SS
China
GB
X15CrNiSi2012 309S24
X12CrNi2521 310S24
X10CrNi18.08
X4CrNiMo165
316S111
58C
Z15CNS20.12 X6CrNi2520
Z12CN2520 X6CrNi2520 F.331
F.8414
Z1NCDU25.20
Z6CND16-04-01
Z8CNA17-07 X2CrNiMo1712
2361
2370
1Cr23Ni13
OCr25Ni20
1.4828
1.4845
1.4406
1.4418
1.4568
1.4504
1.4563
1.4878
X12CrNiTi189 321S32
2584
2378
SUS321
Z1NCDU31-27-03
Z1CNDU20-18-06AZ
Z6CNT18.12B X6CrNiTi18 11 F.3523
309
310S
308
17-7PH
SUH309
SUH310
SCS17
NO8028
S31254
321
58B, 58C
1Cr18Ni9Ti
y HEAT RESISTANT STEELS

USA
AISI/SAE
Japan
JIS
330
HT, HT 50
SUH330
SCH15
Germany
W.-nr.
DIN
1.4864
1.4865
U. K.
BS
EN
X12NiCrSi3616
G-X40NiCrSi3818 330C11
France
AFNOR
Italy
UNI
Z12NCS35.16
XG50NiCr3919
Spain
UNE
Sweden
SS
China
GB
Spain
UNE
Sweden
SS
China
GB
y GRAY CAST IRON

USA
AISI/SAE
No 20 B
No 25 B
No 30 B
No 35 B
No 40 B
No 45 B
No 50 B
No 55 B
A436 Type 2
Japan
JIS
FC100
FC150
FC200
FC250
FC300
FC350
Germany
W.-nr.
DIN
0.6015
0.6020
0.6025
0.6030
0.6035
0.6040
0.6660
GG 10
GG 15
GG 20
GG 25
GG 30
GG 35
GG 40
GGL NiCr202
U. K.
BS
EN
Grade 150
Grade 220
Grade 260
Grade 300
Grade 350
Grade 400
L-NiCuCr202
France
AFNOR
Ft 10 D
Ft 15 D
Ft 20 D
Ft 25 D
Ft 30 D
Ft 35 D
Ft 40 D
L-NC 202
Italy
UNI
G15
G20
G25
G30
G35
FG15
FG25
FG30
FG35
0100
0110
0115
0120
0125
0130
0135
0140
0523
HT150
HT200
HT250
HT300
HT350
HT400
y DUCTILE CAST IRON

USA
AISI/SAE
Japan
JIS
60-40-18
80-55-06
A43D2
100-70-03
FCD400
FCD500
FCD600
FCD700
Germany
W.-nr.
DIN
0.7040
0.7033
0.7050
0.7660
0.7070
U. K.
BS
EN
GGG 40
SNG 420/12
GGG 40.3 SNG 370/17
GGG 35.3
GGG 50
SNG 500/7
GGG NiCr202 Grade S6
GGG NiMn137 L-NiMn 137
GGG 60
SNG 600/3
GGG 70
SNG 700/2
France
AFNOR
Italy
UNI
FCS 400-12 GS 370-17

FGS 370-17
FGS 500-7 GS 500

S-NC202
L-MN 137
FGS 600-3
FGS 700-2 GS 700-2
Spain
UNE
FGE 38-17
FGE 50-7
FGS 70-2
Sweden
SS
07 17-02
07 17-12
07 17-15
07 27-02
07 76
07 72
07 32-03
07 37-01
China
GB
QT400-18
QT500-7
QT600-3
QT700-18
USA
AISI/SAE
Japan
JIS
FCMB310
32510
FCMW330
40010
FCMW370
50005
FCMP490
70003
FCMP540
A220-70003 FCMP590
A 220-80002 FCMP690
Germany
W.-nr.
DIN
0.8145
0.8155
0.8165
GTS-35
GTS-45
GTS-55
GTS-65
GTS-65-02
GTS-70-02
U. K.
BS
8 290/6
B 340/12
P 440/7
P 510/4
P 570/3
P 570/3
P 690/2
EN
France
AFNOR
Italy
UNI
MN 32-8
MN 35-10
Mn 450
MP 50-5
MP 60-3
Mn 650-3
Mn 700-2
GMN45
GMN55
GMN 65
GMN 70
Spain
UNE
Sweden
SS
08 14
08 15
08 52
08 54
08 58
08 56
08 62
China
GB
TECHNICAL DATA
y MALLEABLE CAST IRON
N031
TECHNICAL DATA
SURFACE ROUGHNESS
SURFACE ROUGHNESS
Ten-Point Mean Roughness
Maximum Height
Arithmetical Mean
Roughness
Type Code
Ra
Rz
RZJIS
(From JIS B 0601-1994)
Determination Example (Figure)
Determination
Ra means the value obtained by the following formula and

expressed in micrometer (! m) when sampling only the
reference length from the roughness curve in the direction of
the mean line, taking X-axis in the direction of mean line and
Y-axis in the direction of longitudinal magnification of this
sampled part and the roughness curve is expressed by y=f(x):
Rz shall be that only when the reference length is sampled

from the roughness curve in the direction of the mean line, the
distance between the top profile peak line and the bottom
prole valley line on this sampled portion is measured in the
longitudinal magnification direction of roughness curve and
the obtained value is expressed in micrometer (!m).
(Note) When finding Rz, a portion without an exceptionally
high peak or low valley, which may be regarded as a
aw, is selected as the sampling length.
RZJIS shall be that only when the reference length is sampled
from the roughness curve in the direction of its mean line, the
sum of the average value of absolute values of the heights of
ve highest prole peaks (Yp) and the depths of ve deepest
profile valleys (Yv) measured in the vertical magnification
direction from the mean line of this sampled portion and this
sum is expressed in micrometer (!m).
:altitudes of the ve highest prole peaks of the
sampled portion corresponding to the reference
length l.
:altitudes of the ve deepest prole valleys of the
sampled portion corresponding to the reference
length l.
y RELATIONSHIP BETWEEN ARITHMETICAL MEAN (Ra) AND CONVENTIONAL DESIGNATION (REFERENCE DATA)
Max. Height
Ten-Point Mean Roughness
Ra
Rz
RZJIS
0.08
0.025 a
TECHNICAL DATA
0.05 a
0.25
I (mm)
0.05s
0.05z
0.1 s
0.1 z
0.2 s
0.2 z
0.1
0.4 s
0.4 z
0.2
0.8 s
0.8 z
0.4
0.8
1.6
6.3 s
6.3 z
3.2
12.5 s
12.5 z
6.3
25
25
12.5
25
50
100
0.8
2.5
8
1.6 s
1.6 z
3.2 s
3.2 z
50
50
100
100
200
200
400
400
0.08
0.25
0.8
2.5
8
correlation among the three is shown for convenience and is not exact.
*The
Ra : The evaluation length of Rz and Rz is the cutoff value and sampling length multiplied by 5, respectively.
*
JIS
N032
Conventional Finish
Mark
0.012 a
Rz RZJIS
Standard Series
]]
Cutoff Value
"c (mm)
]]]]
Standard Series
Sampling Length for
]]]
Arithmetical Mean Roughness
HARDNESS COMPARISON TABLE

Standard Tungsten
Carbide
Ball
Ball
Rockwell Hardness (3)

A Scale,
B Scale,
C Scale,
D Scale,
Load: 60kgf, Load: 100kgf, Load: 150kgf, Load: 100kgf,
Diamond
1/16" Ball
Diamond
Diamond
(HRB)
Point (HRA)
Point (HRC) Point (HRD)
Tensile
Strength
(Approx.)
MPa
(2)

(767)
(757)
940
920
900
880
860
85.6
85.3
85.0
84.7
84.4

68.0
67.5
67.0
66.4
65.9
76.9
76.5
76.1
75.7
75.3
97
96
95
93
92

429
415
401
388
375
429
415
401
388
375
455
440
425
410
396
73.4
72.8
72.0
71.4
70.6

45.7
44.5
43.1
41.8
40.4
59.7
58.8
57.8
56.8
55.7
61
59
58
56
54
1510
1460
1390
1330
1270

(745)
(733)
(722)
(712)
(710)
(698)
840
820
800

780
760
84.1
83.8
83.4

83.0
82.6

65.3
64.7
64.0

63.3
62.5
74.8
74.3
73.8

73.3
72.6
91
90
88

87
86

363
352
341
331
321
363
352
341
331
321
383
372
360
350
339
70.0
69.3
68.7
68.1
67.5

(110.0)
(109.0)
(108.5)
(108.0)
39.1
37.9
36.6
35.5
34.3
54.6
53.8
52.8
51.9
51.0
52
51
50
48
47
1220
1180
1130
1095
1060

(684)
(682)
(670)
(656)
(653)
740
737
720
700
697
82.2
82.2
81.8
81.3
81.2

61.8
61.7
61.0
60.1
60.0
72.1
72.0
71.5
70.8
70.7

84
83

81

311
302
293
285
277
311
302
293
285
277
328
319
309
301
292
66.9
66.3
65.7
65.3
64.6
(107.5)
(107.0)
(106.0)
(105.5)
(104.5)
33.1
32.1
30.9
29.9
28.8
50.0
49.3
48.3
47.6
46.7
46 1025
45 1005
970
43
950

925
41

(647)
(638)
630
627
690
680
670
667
81.1
80.8
80.6
80.5

59.7
59.2
58.8
58.7
70.5
70.1
69.8
69.7

80

79

269
262
255
248
241
269
262
255
248
241
284
276
269
261
253
64.1
63.6
63.0
62.5
61.8
(104.0)
(103.0)
(102.0)
(101.0)
100
27.6
26.6
25.4
24.2
22.8
45.9
45.0
44.2
43.2
42.0
40
39
38
37
36
895
875
850
825
800

601
677
640
80.7
79.8

59.1
57.3
70.0
68.7

77

578
640
615
79.8
79.1

57.3
56.0
68.7
67.7

75

235
229
223
217
212
235
229
223
217
212
247
241
234
228
222
61.4
60.8

99.0
98.2
97.3
96.4
95.5
21.7
20.5
(18.8)
(17.5)
(16.0)
41.4
40.5

35
34

33
785
765

725
705

555
607
591
78.8
78.4

55.6
54.7
67.4
66.7

73 2055

534
579
569
78.0
77.8

54.0
53.5
66.1
65.8
2015
71 1985
207
201
197
192
187
207
201
197
192
187
218
212
207
202
196

94.6
93.8
92.8
91.9
90.7
(15.2)
(13.8)
(12.7)
(11.5)
(10.0)

32
31
30
29
690
675
655
640
620

514
533
547
77.1
76.9

52.5
52.1
65.0
64.7
1915
70 1890
(495)

495
539
530
528
76.7
76.4
76.3

51.6
51.1
51.0
64.3
63.9
63.8
1855
1825
68 1820
183
179
174
170
167
183
179
174
170
167
192
188
182
178
175

90.0
89.0
87.8
86.8
86.0
(9.0)
(8.0)
(6.4)
(5.4)
(4.4)

28
27

26
615
600
585
570
560
(477)

477
516
508
508
75.9
75.6
75.6

50.3
49.6
49.6
63.2
62.7
62.7
1780
1740
66 1740
(461)

461
495
491
491
75.1
74.9
74.9

48.8
48.5
48.5
61.9
61.7
61.7
1680
1670
65 1670
163
156
149
143
137
163
156
149
143
137
171
163
156
150
143

85.0
82.9
80.8
78.7
76.4
(3.3)
(0.9)

25

23
22
21
545
525
505
490
460

444
474
472
472
74.3
74.2
74.2

47.2
47.1
47.1
61.0
60.8
60.8
1595
1585
63 1585
131
126
121
116
111
131
126
121
116
111
137
132
127
122
117

74.0
72.0
69.8
67.6
65.7

20
19
18
15
450
435
415
400
385
444

TECHNICAL DATA
MPa
(2)
Brinell Hardness (HB),

10mm Ball,
Load: 3,000kgf
Shore Hardness (HS)
A Scale,
B Scale,
C Scale,
D Scale,
Load: 60kgf, Load: 100kgf, Load: 150kgf, Load: 100kgf,
Diamond
1/16" Ball
Diamond
Diamond
(HRB)
Point (HRA)
Point (HRC) Point (HRD)
Tensile
Strength
(Approx.)
Vickers
Hardness (HV)
Tungsten
Standard
Carbide
Ball
Ball
Rockwell Hardness (3)
Shore Hardness (HS)
Brinell Hardness (HB),

10mm Ball,
Load: 3,000kgf
Vickers
Hardness (HV)
HARDNESS CONVERSION NUMBERS OF STEEL
(Note 1) The above list is the same as that of AMS Metals Hand book with tensile strength in approximate metric value and Brinell hardness
over a recommended range.
(Note 2) 1MPa=1N/mm2
(Note 3) Figures in ( ) are rarely used and are included for reference. This list has been taken from JIS Handbook Steel I.
N033
TECHNICAL DATA
CUTTING TOOL MATERIALS

The chart below shows the relationship between various tool materials, in relation with hardness on a vertical axis
and toughness on a horizontal axis.
Today, cemented carbide, coated carbide and TiC-TiN-based cermet are key tool materials in the market. As they
offer a high balance of hardness and toughness.
Sintered Diamond
Diamond Coating
Sintered CBN
Hardness
Ceramics
Coated Carbide
Coated Cermet
Coated Micro-grain
Cemented Carbide
Cermet
Micro-grain Cemented Carbide
Cemented Carbide
Coated
HSS
Powder HSS
HSS
Toughness
TECHNICAL DATA
Thermal
Conductivity
(W/mk)
Thermal
Expansion
(x 10-6/k)
Tool Material
Highly Soluble
2100
3.1
Sintered Diamond
1300
4.7
Sintered CBN
1600
100
3.4
Ceramics
AI2O3
2100
-100
i0
29
7.8
TiC
3200
-35
< 0.5
21
7.4
TiN
2500
-50
29
9.4
TaC
1800
-40
0.5
21
6.3
Cemented Carbide
WC
2100
-10
5.2
Cemented Carbide
Hard Materials
Hardness
(HV)
Diamond
>9000
CBN
>4500
Si3N4
Energy Formation Solubility in Iron

(kcal/g atom)
(%.1250r)
121
N034
Ceramics
Cemented Carbide
Cermet
Coated Carbide
Cermet
Coated Carbide
1W/m K=2.3910-3cal/cm sec r
GRADE CHAIN
P
Steel
M Stainless
Steel
Cemented
Carbide
UTi20T
UTi20T
Cast
Iron
HTi05T
NonFerrous
HTi10
HTi10

Ti Alloy RT9005 RT9010
Steel
UTi20T
TF15
UE6105 UE6110 UE6020 UE6035
F7010
F7030
VP10MF VP20MF VP15TF VP30RT

(PVD)
M Stainless
Steel
US7020
US735
F7010
F7030
VP10MF VP20MF
(PVD)
Cast
Iron
NonFerrous
Coated
Carbide
UC5115

US905
Ti Alloy
Hardened
H
Materials
VP05RT
Steel
M Stainless
Steel
MP8010
NX2525
VP15TF VP30RT UP20M

(PVD)
(PVD)
VP15TF
(PVD)
VP15TF
(PVD)
MP9030
(PVD)
VP15TF
(PVD)
NX55
NX3035
NX4545
NX2525 NX4545
Cast
Iron
NX2525
Steel
AP25N
VP25N
(PVD)
M Stainless
Steel
VP10RT
(PVD)
(PVD)
Coated Cermet
(PVD)
LC15TF
NEW
Cermet
MC5020
(PVD)
(PVD)
For Cutting Tools
UC5105
(PVD)
(PVD)
VP45N
(PVD)
(PVD)
AP25N
(PVD)
AP25N
VP25N
(PVD)
Non-Ferrous
Non-Metal
(PVD)
MD220
(Sintered Diamond)
Sintered
Alloy
MB4020
Polycrystallines
NEW
Cast
Iron
MB710
MB5015 MB730
MBS140
BC5030
Hardened
Materials MBC010 MBC020 BC8020 MB810
MB8025
MB825
MF20
MF30
(Sintered CBN)
NEW
MB835
TECHNICAL DATA
Cast
Iron
(Sintered CBN)
Micro-Grain
Cemented Carbide
Steel
Cast Iron
SF10
MF07
MF10
TF15
N035
TECHNICAL DATA
GRADE COMPARISON TABLE

CEMENTED CARBIDE
Classication
ISO
Mitsubishi Kennametal
Symbol
P01
P10
P10
P20
UTi20T
P30
UTi20T
Turning
Milling
TECHNICAL DATA
SRT
WS10
SMA
IC70
IC50M
ST20E
TX20
TX25
SRT
DX30
EX35
SM30
IC50M
IC54
A30
A30N
TX30
UX30
SR30
DX30
EX35
EX40
IC54
ST40E
TX40
SR30
DX35
EX45
EH510
U10E
TU10
UMN
WA10B
IC08
EH520
U2
TU20
UX30
DX25
UMS
EX35
A30
A30N
UX30
DX25
UMS
EX40
EX45
UM40
EX45
WH01
WH05
890
M20
UTi20T
K68
KMF
K125M
TTM
H13A
HX
883
M30
UTi20T
K600
TTR
H10F
SM30
IC08
IC28
G13
S6
IC128
K01
HTi05T
K605
H1P
K10
HTi10
K20
UTi20T
K30
UTi20T
HTi10
N30
S01
RT9005
RT9010
S20
RT9010
TF15
S30
P10
P20
P30
P40
M10
M20
H1
H2
TU40
TH03
KS05F
KG03
H1P
H10
HM
890
IC20
EH10
EH510
G1F
TH10
KW10
KG10
KT9
WH10
H13A
890
HX
883
IC20
G10E
EH20
EH520
G2F,
KS15F
G2, KS20
GW25
CR1
KG20
WH20
G10E
G3
H1
H2
KS05F
KW10
IC20
EH10
EH510
TH10
H10T
KW10
GW15
IC20
G10E
EH20
EH520
KS15F
THR
883
H10
H13A
K313
K110M
THM
THM-U
K715
KMF
K600
G13
THR
890
H15
HX KX
883 H15
H25
H25
883
KG30
TF15
KT9
WH10
CR1
WH20
KG03
K10
K313
THM
H10
H10A
H10F
H13A
K715
KMF
G13 K600
THR
890
IC07
IC08
EH10
EH510
KS05F
TH10
KW10
FZ05
KG10
890 883
HX H25
IC07
IC08
EH20
EH520
KS15F
KS20
KW10
FZ15
KG20
KG30
S1P
UTi20T
K125
UTi20T
GX
K600
IC50M
IC28
IC50M
IC28
IC28
A30N
TX25
A30N
UX30
PW30
UX40
PW30
K110M
UTi20T
K313
IC20
A30N
TX25
M30
M40
K01
K10
UTi20T
KFM
K600
IC28
A30N
UX30
HTi10
K110M
K313
K20
UTi20T
KFM
K30
UTi20T
IC28
SRT
SRT
DX30
SR30
DX30
SR30
UMN
DX25
UMS
DX25
UMS
TU40
HTi05T
EX35
EX35
EX40
EX45
EX35
EX40
EX45
EX45
KG03
H1P
HX
IC20
G10E
IC20
G10E
TH10
(Note) The above table is selected from a publication. We have not obtained approval from each company.
N036
PW30
RT9005
S10
Hitachi
Tool
TX10S
H10A
K605
Dijet
ST10P
K313
N01
Kyocera
IC70
M10
K313
K110M
THM
THM-U
K715
KMF
K600
Sumitomo Tungaloy
S1P
S6
N20
Iscar
G13
N10
Seco
Tools
P40
M40
K125M
TTM
GK
K600
TTR
Sandvik
KW10
GW25
KG10
WH10
GW25
KT9 CR1
KG20
WH20
KG30
MICRO GRAIN
Classication
Cutting Tools
ISO
Symbol
Mitsubishi
Z01
SF10
MF07
MF10
6UF
8UF
PN90
Z10
HTi10
MF20
H3F
H6F
H6FF
890
Z20
TF15
MF30
H10F
890
883
H15F
883
Kennametal
Z30
Sandvik
Seco
Tools
Sumitomo
Tungaloy
Kyocera
F
MD08F
MD1508
M
MD10
MD05F
MD07F
F0
XF1
F1
AFU
AF0
SF2
AF1
A1
CC
FW30
Dijet
Hitachi
Tool
FZ05
FB05
FB10
NM08
FZ10
FZ15
FB15
NM15
FZ15
FB15
FB20
FZ20
FB20
MD20
BM10
UM
BRM20
EF20N
NM25
CERMET
Turning
ISO
Symbol
P01
AP25N
P10
AP25N
NX2525
KT125
KT315
P20
AP25N
NX2525
NX3035
KT5020
KT325
KT1120
P30
VP45N
M10
NX2525
AP25N
M20
NX2525
AP25N
NX3035
KT125
Sandvik
CT5015
GC1525
Seco
Tools
CM
CMP
T110A
T2000Z
IC20N
IC520N
IC530N
T1200A
T2000Z
T1500A
CM
CMP
Milling
T3000Z
T1200A
T2000Z
NS520
AT520
GT520
GT720
NS520
AT530
GT720
GT730
NS530
GT530
GT730
NS730
NS530
NS730
NS520
AT530
GT530
GT720
NS530
GT730
NS730
Kyocera
TN30
PV30
TN60
TN6010
PV60
PV7010
TN90
TN6020
PV90
PV7020
PV7025
TN90
PV90
TN60
TN6020
PV60
PV7020
TN90
TN6020
PV90
PV7020
PV7025
Dijet
Hitachi
Tool
LN10
CX50
CX50
CX75
PX75
CZ25
CX75
PX75
PX90
CH550
PX90
LN10
CX50
CX50
CX75
CH550
T3000Z
K01
AP25N
NX2525
K10
AP25N
NX2525
K20
AP25N
NX2525
P10
NX2525
P20
NX2525
P30
NX4545
IC30N
M10
NX2525
IC30N
M20
NX2525
M30
NX4545
K01
K10
NX2525
K20
T1200A
T2000Z
T3000Z
T1500A
T110A
T2000Z
M30
Sumitomo Tungaloy
IC20N
IC520N
IC20N
IC75T
IC30N
IC520N
IC530N
IC75T
IC30N
GC1525
GC1525
Iscar
NX2525
KT125
KT325
CT5015
T110A
T2000Z
NS710
NS520
AT520
GT520
GT720
TN30
PV30
PV7005
LN10
T1200A
T2000Z
NS520
GT530
GT730
NS730
TN60
TN6020
PV60
PV7020
PV7025
LN10
T3000Z
KT530M
HT7
KT605M
KT530M
HT7
KT605M
CT530
CT530
C15M
IC30N
C15M
IC30N
C15M
CX75
NS530
T250A
TN60
CX75
TN100M
CX75
CX90
CH550
CH7030
MZ1000
MZ2000
CX90
CX99
MZ3000
CH7035
NS530
NS540
NS740
TN60
IC30N
NS530
T250A
TN100M
NS540
NS740
NS530
KT530M
HT7
CX75
CX90
CX99
CH550
CH7030
MZ1000
MZ2000
MZ3000
CH7035
TECHNICAL DATA
Classication
TN60
CX75
N037
TECHNICAL DATA

CVD COATED GRADE
Classication
Turning
S
P
ISO
Symbol
Milling
IC9150
IC8150
IC428
IC9150
IC9015
IC8150
IC8250
IC9015
IC8250
IC9025
IC9250
IC8350
KCP05
KC9105
GC4205
GC4005
TP0500
TP1500
P10
UE6105
UE6110
KCP10
KCP25
KC9110
GC4215
GC4015
TP1500
TP2500
P20
UE6110
UE6020
KCP25
KC9125
GC4215
GC4225
GC4015
GC4025
TP2500
P30
UE6020
UE6035
UH6400
US735
KCP30
KCP40
KC8050
GC4225
GC4235
GC4025
GC4035
TP3500
TP3000
P40
UE6035
UH6400
US735
KCP30
KCP40
KC9140
KC9040
KC9240
KC9245
GC4235
GC4035
TP3500
TP3000
M10
US7020
KCM15
GC2015
TM2000
M20
US7020
KCM15
KC9225
GC2015
TM2000
M30
US735
GC2025
TM4000
M40
US735
GC2025
TM4000
IC9350
K01
UC5105
KCK05
GC3205
GC3210
TH1500
TK1000
K10
UC5115
KCK15
KCK20
KC9315
GC3205
GC3210
GC3215
TK1000
TK2000
K20
UC5115
UE6110
KCK20
KC9110
KC9325
GC3215
TK2000
K30
UE6110
KC9125
KC9325
IC5005
IC9007
IC5005
IC5010
IC9150
IC428
IC4028
IC5010
IC8150
IC9150
IC9015
IC418
IC9015
IC418
S01
US905
KCM25
KC9230
KCM35
KC9240
KC9245
FH7020
F7030
KC930M
KC935M
M20
F7030
KC925M
M30
F7030
KC930M
K20
K30
JC110V
HG8010
AC810P
AC700G
AC2000
AC820P
T9005
T9115
CA5505
CA5515
JC110V
JC215V
HG8010
HG8025
GM8020
AC2000
AC820P
AC830P
T9115
T9125
CA5515
CA5525
CR9025
JC110V
JC215V
HG8025
GM8020
GM25
IC8350
IC9250
IC9350
AC830P
AC630M
T9125
T9035
CA5525
CA5535
CR9025
JC215V
JC325V
GM25
GM8035
IC9350
AC630M
T9035
CA5535
JC325V
JC450V
GM8035
GX30
AC610M
T9115
CA6515
JC110V
AC610M
AC630M
T6020
T9125
CA6515
CA6525
JC110V
AC630M
T6030
CA6525
IC9250
IC8250
IC9250
IC9025
IC656
IC9350
IC635
HG8025
GM25
GM8035
GX30
AC630M
GX30
AC410K
T5105
CA4505
CA4010
JC050W
JC105V
HG3305
AC410K
AC420K
AC700G
T5115
CA4515
CA4010
CA4115
JC050W
JC105V
JC110V
HG3315
HG8010
AC420K
AC700G
AC820P
T5115
T5125
CA4515
CA4115
CA4120
JC110V
JC215V
HG8025
GM8020
AC820P
T5125
JC215
HG8025
GM8020
MP1500
MP2500
GC4230
MP2500
IC4050
JC730U
ACP100
T3130
ACP100
T3130
JC730U
GX2030
GC4240
MP2500
GC2040
GX2030
GX2030
GX30
GF30
MP2500
KC930M
KC935M
IC9250
IC520M
IC9350
IC9350
IC4050
ACP100
T3130
ACP100
T3130
JC730U
GF30
GX30
GF30
GX30
IC635
JC600
MC5020
F5010
MC5020
F5020
ACK100
KC915M
GC3220
K20W
MK1500
IC5100
IC9150
KC920M
KC925M
KC930M
KC935M
GC3040
MK3000
IC4100
IC4050
IC520M
ACK200
T1115
T1015
T1115
T1015
N038
Hitachi
Tool
CA5505
K01
K10
Dijet
T9005
GC4220
M10
M40
Kyocera
AC810P
AC700G
IC9080
IC4100
IC9015
IC5100
IC520M
MP1500
F7030
Sumitomo Tungaloy
S05F
P10
P40
TECHNICAL DATA
Iscar
UE6105
P30
Seco
Tools
P01
P20
Sandvik
JC600
JC610
JC610
GX2030
GX30
PVD COATED GRADE

P
ISO
Symbol
VP10MF
KC5010
KC5510
KU10T
GC1525
GC1025
P20
VP10RT
VP20RT
VP15TF
VP20MF
KC5025
KC5525
KC7215
KC7315
KU25T
GC1525
GC1025
GC1125
CP250
TS2500
P30
VP10RT
VP20RT
VP15TF
VP20MF
KC7015
KC7020
KU25T
KC7235
GC1025
GC1125
CP500
Turning
M30
KC7040
KC7140
KC7030
VP10MF
VP10RT
VP20RT
VP15TF
VP20MF
VP10RT
VP20RT
VP15TF
VP20MF
GC1005
GC1025
GC1125
GC1105
GC1005
GC1025
GC1125
GC1105
KC7030
KC7225
GC1125
GC2035
CP200
TS2000
CP250
TS2500
CP500
CP500
GC2035
Kyocera
Dijet
Hitachi
Tool
IC250 IC350
IC507 IC570
IC807 IC907
IC908
IC228 IC250
IC308 IC328
IC350 IC354
IC507 IC528
IC570 IC807
IC808 IC907
IC908 IC928
IC1008 IC1028
IC3028
IC228 IC250
IC328 IC330
IC354 IC528
IC1008
IC1028 IC3028
IC228 IC328
IC330 IC528
IC1008
IC1028 IC3028
AH710
PR915 PR1005
PR930 PR1025
PR1115 PR1225
AH710
AH725
AH120
SH730
GH730
GH130
PR930
PR1025
PR1115
PR1225
IP2000
AH725 AH120
SH730 GH730
GH130 AH740
J740
IP3000
AH740
J740
IC330 IC354
IC507 IC520
IC570 IC807
IC907 IC3028
IC250 IC330
IC354 IC808
IC908 IC1008
IC1028 IC3028
IC228 IC250
IC328 IC330
IC1008 IC1028
IC3028
IC328
IC928 IC1008
IC1028 IC3028
AC510U
AC520U
AC520U
AC530U
AC530U
AH710
AH710 AH725
AH120 SH730
GH730 GH130
GH330
GH330 AH725
AH120 SH730
GH730 GH130
J740
PR915
PR1025
PR1225
JC5003
JC8015
IP050S
PR1025 PR1125 JC5003

PR1225
JC5015
PR915 PR930 JC8015
IP100S
PR1125
JC5015
JC8015
J740
K01
K10
KC5010
KC7210
CP200
TS2000
IC350
IC1008
K20
VP10RT
VP20RT
VP15TF
KC7015
KC7215
KC7315
CP200
CP250
TS2000
TS2500
IC228 IC350
IC808 IC908
IC1008
K30
VP10RT
VP20RT
VP15TF
KC7225
CP500
IC228 IC350
IC808 IC908
IC1008
S01
S10
S20
S30
Milling
CP200
TS2000
CP500
KC5010
KC5510
KC6005
KC6015
KC5025
KC5525
KC7020
KC7025
M40
Sumitomo Tungaloy
M01
M20
Iscar
PR915
PR1005
P10
M10
Seco
Tools
P01
P40
Sandvik
VP05RT
VP05RT
VP10RT
VP20RT
VP10RT
VP20RT
VP15TF
VP15TF
IC507 IC907
KC5010
KC5410
KC5510
KC5025
KC5525
GC1105
GC1005
GC1025
GC1025
GC1125
CP200 CP250
TS2000
TS2500
CP250
TS2500
CP500
GH110
AH110
PR905
AH710
GH110
AH110 AH710
PR905
AH725 AH120
GH730 GH130
AH725
AH120
GH730
GH130
AH905
AH905 SH730
AH110
AH120
JC5003 JC8015
JC5003
JC5015
JC8015
JC5015
JC8015
IC507
IC903
AC510U
IC300 IC808
IC908 IC928
IC3028
AC510U
AC520U
AH120
AH725
PR1125
AC520U
AH725
PR1125
GC1125
P01
JC5003
P10
KC715M
GC1010
GC1025
P20
KC522M
KC525M
GC1025
GC1010
GC2030
VP15TF
F25M
MP3000
IC250 IC350
IC808 IC810
IC900 IC903
IC908 IC910
IC950
IC250 IC300
IC328 IC330
IC350 IC528
IC808 IC810
IC830 IC900
IC908 IC910
IC928 IC950
IC1008
ACP100
ACP200
ACP200
AH725
AH120
GH330
AH330
PR730
PR830
PR1025
PR1225
JC5003
JC5030
JC8015
JC5015
JC5118
PR730
PR830
PR1025
PR1225
PR1230
JC5015
JC5030
JC5040
JC8015
JC5118
ATH80D
PTH08M
PCA08M
PCS08M
ACS05E
CY9020
JX1005 JX1020
PC20M JP4020
PCA12M
CY150
CY15
JX1015
TECHNICAL DATA
Classication
N039
TECHNICAL DATA

Classication
ISO
Symbol
Sandvik
Seco
Tools
Iscar
IC250 IC300
IC328 IC330
IC350 IC528
IC830 IC900
IC928 IC950
IC1008
P30
VP15TF
VP30RT
KC725M
KC530M
GC1010
GC1030
GC2030
F25M
MP3000
F30M
P40
VP30RT
KC735M
GC1030
F40M
T60M
KC715M
GC1025
GC1030
M01
M10
IC903
M20
VP15TF
VP20RT
KC730
KC522M
KC525M
GC1025
GC1030
GC1040
GC2030
F25M
MP3000
M30
VP15TF
VP20RT
VP30RT
KC725M
KC735M
GC1040
GC2030
F30M
F40M
MP3000
M40
VP30RT
IC250 IC300
IC808 IC830
IC900 IC908
IC928
IC1008
IC250 IC300
IC328 IC330
IC830 IC928
IC1008
F40M
Sumitomo Tungaloy
ACP200
ACP300
AH725
AH120
AH130
AH140
GH130
AH730
ACP300
AH140
ACP200
ACP200
ACP300
ACP300
ACP300
Milling
K10
TECHNICAL DATA
KC510M
GC1010
K20
VP15TF
VP20RT
KC520M
KC525M
GC1010
GC1020
K30
VP15TF
VP20RT
KC725M
KC735M
GC1020
IC350 IC810
IC830 IC900
IC910 IC928
IC950
IC1008
MK2000
IC350 IC808
IC810 IC830
IC900 IC908
IC910 IC928
IC950 IC1008
IC350 IC808
IC830 IC908
IC928 IC950
IC1008
ACK300
PR730
PR660
PR1025
PR1225
JC5015
JC5040
JC5118
JC8015
PR660
PR1210
PR905
JC5015
JC5080
JC8015
CY150
CY15
PTH13S
JX1015
JC5015
JC8015
JC5080
CY250 GX2030
GX30
CY25 PTH40H
PTH30E JX1045
ACK300
PR905
S20
VP15TF
MP9030
KC522M
KC525M
GC1025
GC2030
IC300 IC908
IC808 IC900
IC830 IC928
IC328 IC330
EH520Z
EH20Z
ACK300
PR905
KC725M
GC2030
S30T
IC830 IC928
ACK300
H30
VP15TF
IC903
GC1010
GC1030
KC635M
GC1010
GC1030
KC530M
MH1000
F15M
IC900
F15M
IC900 IC808
IC908
IC1008
MP3000
F30M
IC808 IC908
IC1008
CY250
CY25
HC844
JX1045
JX1060
GF30
GX30
ATH80D
PTH08M
PCA08M
PCS08M
ASC05E
JX1005
JX1020
CY9020
CY100H
CY10H
GH130
EH520Z
EH20Z
KC635M
CY150
CY15
JX1015
JC5003
JC8015
IC903
VP15TF
JS4060
CY250
CY25
HC844
JX1045
PTH30E
JS4060
PTH40H
JX1060
GF30
GX30
PCS08M
CY9020
JX1020
PR1210
PR905
C1025
H10
Hitachi
Tool
AH110
GH110
AH725
AH120
GH130
AH330
KC510M
MP8010
JC5015
JC8015
JC8050
JC5118
JC5015
JC5118
JC8050
JC5003
VP15TF
H20
N040
JC5118
S10
H01
JC5015
JC5040
JC8015
JC5118
PR730
PR1025 PR1225
PR905
F40M
Dijet
JC5040
JC5118
AH140
S01
S30
PR660
PR1230
AH110
GH110
AH330
K01
AH725
AH120
GH330
AH330
GH110
AH120 AH725
AH130 AH140
GH130 AH730
GH340
Kyocera
JC5003
JC8015
JC5118
JC5003
JC5015
JC8015
JC5118
JC8015
JC5015
JC8050
JC5118
JC8050
JC5118
JC8003
JC8008
JC8003
JC8008
JC8015
JC5118
JC8015
JC5118
PCS08M
PTH13S
JS1025
CY100H
CY10H
BH200
BH250
ATH80D
PTH08M
PCA08M
JX1005
CBN
Classication
ISO
Symbol
Turning
Mitsubishi
Sandvik
H01
MBC010
MB810
H10
MBC020
BC8020
MB8025
CB7015
CB20
H20
BC8020
MB8025
MB825
CB7025
CB7050
CB50
H30
BC8020
MB835
S01
MB730
Seco
Tools
CBN050C
CBN10
CBN100
CBN100P
CBN150
CBN150
CBN200
CBN300
CBN300P
CBN350
Element
Six
Sumitomo
Tungaloy
Kyocera
Dijet
DBC50
BNC100
BNX10
BXM10
BXC30
BX310
KBN05M
KBN10M
KBN10C
KBN510
DCC500
BNC160
BNX20
BN2000
BXM20
BXA30
BX330
KBN25M
KBN25C
KBN525
JBN300
BXM20
BXA40
BX360
KBN30M
JBN245
DCN450
DCX650
BNC200
BNX25
BN2000
BN250
BNC300
BN350
BN700
BXC50
BX380
BX450
BX950
BX480
KBN35M
S10
S20
S30
K01
K10
K20
K30
Sintered Alloy
MB710
MB5015
MB710
MB5015
MB730
MB730
MBS140
BC5030
MBS140
BC5030
CB50
CB7050
BX930
KBN60M
JBN795
JBN330
CBN300
CBN300P
DBA80
BN700
BX950
KBN60M
KBN900
CBN200
DBW85
DBS900
AMB90
BN700
BNS800
BXC90
BX90S
KBN900
BNS800
BXC90
BX90S
CBN350
MB4020
MB835
BN500
CBN200
DBW85
DBS900
BN7500
BN700
BX470
BX480
KBN65B
KBN65M
KBN70M
DIAMOND
INNOVATIONS
Element
Six
Sumitomo
Tungaloy
Kyocera
PCD
Classication
Turning
ISO
Symbol
N01
Mitsubishi
MD205
N20
MD205
MD220
MD220
MD230
N30
MD230
N10
Sandvik
CD10
1800
CTH025
DA90
DX180
DX160
KPD001
1500
CTB010
DA150
DX140
KPD001
KPD010
1300
CTB002
DA2200
DX120
KPD230
DA1000
DX110
1600
Dijet
JDA30
JDA735
JDA40
JDA745
JDA10
JDA715
TECHNICAL DATA
N041
TECHNICAL DATA
INSERT CHIP BREAKER COMPARISION TABLE

NEGATIVE INSERT TYPE
ISO
Classication
Cutting
Mode
PK
P
Finish
Sandvik
Seco
Sumitomo
Tungaloy
01
DP
QF
FF1
FA
TF
GP, VF
FL
ZF
XP, XP-T
FH
UF, FF
FY
C
Light
PF
Light
(Mild Steel)
SY
Light
(With Wiper)
SW
LF, FN
HQ, CQ
17
XQ, XS
NM, ZM, AS
CJ, GS
UG
TM
PS, HS
PG
AH
SM
M5
GE, UX
DM, 37
PT, CS
UB
AY, AE
UD, GG
AR, RE
UC
TE, UE
GH
RN
HZ
MR
PR, HM
Std.
QR, PR
RM, RH
HR
W-M3
W-MF5
MR6, MR7
TECHNICAL DATA
MU
TH
MX, ME
N042
PH
GT, HT
R4, R5, R6
MP
57
PX
57, RR6, R7
HG, HP
65, TU
HX
HX
SH
K, FP
MF
MS
P, MP
MM
MF4
HE, H
SU
SS
EX, UP
SA, SM
S
GH
M5, MR7
MR
RP
56, R6
MQ, GU
MS, MU
SU, HU
ST
MP, SE
SF
PV, DE
SG
SZ
MP
MR
Finish
Light
MA
FN
KF
Medium
Std.
Std., UN
Heavy
Flat Top
Finish
FJ
Light
MJ, MJ
Medium
MS
pNGP
pNGP
23, SM
M1
Heavy
GJ
MS
SR, SMR
M5, MR3
FS, K
M4
UZ
CF
Std.
VA
KM
GZ, UX
CM, 33, Std.
C, ZS, GC
KR
Flat Top
CH, Flat Top
Flat Top
SF
SGF
MF1
*
*
SU
TK
SA, HMM
Peripheral ground type insert.

(Note) Above charts are based on published data and not authorized by each manufacturer.
CT, AB
R8, RR9
HZ
WP, WQ
GUW
ES
Heavy
BH, CE
GU
WMX, WM
LUW, SEW AFW, ASW
BE
UA, UT
MF3
Medium
-Heavy
Medium
TSF, TS
MF5, M3
MW
Finish
Light
SX, SE
UR
PM
HV
NS, 27
QM, 61
MW
HX
PF
LU
MG, MN
Medium
(With Wiper)
W-MF2
FE
WP, WF
MH
Heavy
MF2
Hitachi
FW
MP
MA
MF
Dijet
SU
SA
SH
Medium
Kyocera

ISO
Classication
Cutting
Mode
P
SMG
Finish
Light
FV
11, UF
SV
LF
SW
FW
Medium
Finish
Light
(With Wiper)
Sandvik
LF
UM
Seco
UF, PF
WK
WF, WP
Sumitomo
* *
FC, SC
Tungaloy Kyocera
* *
JS, 01
* *
* *
CF, CK
FP, LU
PF, PSF
GP
F1
SU, SK
PS, PSS
XP, VF
W-F1
LUW
23
HQ
PM, 24
XQ, GK
Std.
MF
UM, PM
F2
MU
Medium
(With Wiper)
MW
MW
WM
W-F2
FinishLight
SV
MF
Medium
Std.
MM
Medium
Flat Top
KF, KM, KR
Medium
AZ
HP
Finish
Light
FJ
*
HP*
SS
Flat Top
JQ
FT
Flat Top
CM
JE
MP
Flat Top
FT
*
*
ACB *
Hitachi
GQ, GF
FF1
MV
Dijet
ASF
AL
AL
LF
* *
AG, AW
SC
AL
AH
ALU


Cutting
Mode
P
Finish
Light
FV, SMG
UF
SV
LF
MV
MF
Sandvik
PF
Seco
Sumitomo
Tungaloy Kyocera
FK
01
LU
PF, PSF
SU
PS, PSS
PM
Medium
PM
MU
23
FinishLight
SV
MF
Medium
MV
MM
GF, XP
HQ
XQ
24
SS
GP, CF
Dijet
Hitachi
JQ
JE
MP
TECHNICAL DATA
ISO
Classication

N043
MMC METAL FRANCE S.A.R.L. (France)
MITSUBISHI MATERIALS U.S.A. CORPORATION

Los Angeles
Chicago
Toronto
MIRACLE TOOLS
AMERICA, LLC
MMC HARTMETALL GmbH (Germany)

MMC HARDMETAL U.K.LTD (United Kingdom)
MMC HARDMETAL POLAND Sp.z o.o. (Poland)
MMC HARDMETAL OOO LTD. (Russia)
Ireland
Norway
Finland
Estonia
Sweden Latvia
Lithuania
Belarus
Belgium Czech Slovakia Ukraine
Switzerland Austria Hungary
Denmark
Netherlands
Portugal
RFM
MMC METAL DE MEXICO,

S.A. DE C.V.
(Mexico)
Columbia
Lima
Slovenia Romania
Turkey
Greece
MMC ITALIA
(Italy)
MITSUBISHI MATERIALS
~
ESPAN A, S.A.
(Spain)
Santa Craz
TIANJIN TIANLING CARBIDE TOOLS CO. LTD.

TIANJIN LINGYUN TOOL DESIGN CO. LTD.
(China)
(SHANGHAI) CORPORATION
Beijing
Seoul
Tianjin
Shanghai Daegu
Delhi Chongqing
S.R.L.
Taipei
Jamshedpur Guangzhou
Hanoi
Mumbai Pune
Hong Kong
Chennai
Manila
Bangkok
Ho Chi Minh
Kuala Lumpur
Singapore
Bangalore
Jakarta
Coimbatore
TSUKUBA PLANT
GIFU PLANT
AKASHI PLANT
MMC TAISHIN TOOL

CO., LTD.
(Taiwan)
Johannesburg
Santiago
Adelaide
Buenos Aires
Sales Ofce
Factory
MMC-METAL DO BRASIL LTDA.

(Brazil)
MMC HARDMETAL INDIA PVT. LTD.

(India)
Representative Ofce
Sydney
Melbourne
Auckland
MMC TOOLS (THAILAND) CO., LTD. MMC Hardmetal (Thailand) Co., Ltd.
(Thailand)
(Thailand)
Agency
Chicago
MIRACLE TOOLS
AMERICA, LLC
Toronto
Los Angeles
RFM
MMC METAL DE MEXICO,

S.A. DE C.V.
(Mexico)
OVERSEAS SALES OFFICES

http://www.mitsubishicarbide.com
JAPAN
MITSUBISHI MATERIALS CORPORATION
Area Marketing & Operations Department
KFC bldg., 8F, 1-6-1, Yokoami, Sumida-ku, Tokyo 130-0015 Japan
TEL +81-3-5819-8772
FAX +81-3-5819-8773
NORTH AMERICAN OFFICES
CHINA
MITSUBISHI MATERIALS(SHANGHAI)CORPORATION
Room 3911,UNITED PLAZA 1468,Nanjing Road West, Shanghai,
200040 China
TEL +86-21-6289-0022
FAX +86-21-6279-1180
THAILAND
MMC Hardmetal (Thailand) Co., Ltd.
8th Floor Regent House Building, 183 Rajdamuri Road,Lumpini,
Pathumwan, Bangkok 10330, Thailand
TEL +66-2651-9800
FAX +66-2651-9803
INDIA
Customer Service : 800-523-0800

Technical Service : 800-486-2341
LOS ANGELES HEAD OFFICE
11250 Slater Avenue, Fountain Valley, CA 92708
TEL : 714-352-6100
FAX : 714-668-1320
CHICAGO OFFICE
1314B North Plum Grove Road, Schaumburg, IL 60173
TEL : 847-252-6300
FAX : 847-519-1732
TORONTO OFFICE
6535 Millcreek Drive, Units 63&64, Mississauga, Ontario L5N 2M2, Canada
TEL : 905-814-0240
FAX : 905-814-0245
MMC HARDMETAL INDIA PVT. LTD.

2/10, 1st Floor, 80 Feet Road, R.M.V 2nd Stage,
Bangalore - 560 094 Karnataka India
TEL +91-80-2351-6083
FAX +91-80-2351-6080
MMC METAL DE MEXICO, S.A. DE C.V.

Av. La Caada No.16, Parque Industrial Bernardo Quintana,
El Marques, Queretaro, CP76246, Mexico
TEL : +52-442-221-6136
FAX : +52-442-221-6134
GERMANY
MMC HARTMETALL GmbH
Comeniusstr. 2, 40670 Meerbusch Germany
TEL +49-2159-91890
FAX +49-2159-918966
BRAZIL
MMC-METAL DO BRASIL LTDA.
Rua Cincinato Braga, 340, 13 Andar,
Bela Vista-CEP 01333-010, So Paulo-SP, Brazil
TEL +55-11-3506-5600
FAX +55-11-3506-5688
ISO 9001 , ISO 14001

(JSAQ080) (JSAE036)
The Scope of the Registration:
Design, development and
manufacturing of metal cutting
tools and blanks of cemented
carbide and other hard materials

TSUKUBA PLANT (JAPAN)

LOS ANGELES HEAD OFFICE
ISO 9001
(JSAQ094)

GIFU PLANT (JAPAN)

AKASHI PLANT (JAPAN)

Mits C005A (2011 2012) GeneralCataloge

Încărcat de

Informații document

Descriere originală:

Titlu original

Drepturi de autor

Formate disponibile

Partajați acest document

Partajați sau inserați document

Opțiuni de partajare

Vi se pare util acest document?

Este necorespunzător acest conținut?

Drepturi de autor:

Formate disponibile

Mits C005A (2011 2012) GeneralCataloge

Încărcat de

Drepturi de autor:

Formate disponibile

USING THIS CATALOG

catalog was made in JANUARY 2011.

note that products in this catalog are

(Note) Please contact us regarding grades and order numbers

HOW TO USE THIS CATALOG

NEGATIVE INSERTS WITH HOLE

SCooTYPE ... SQUARE 90 .................... A117

CNooTYPE... RHOMBIC 80 .................. A068

NEGATIVE INSERTS WITHOUT HOLE

KNooTYPE... PARALLELOGRAM 55 ... A098

POSITIVE INSERTS WITH HOLE

CCooTYPE... RHOMBIC 80 .................. A101

POSITIVE INSERTS WITHOUT HOLE

RTG TYPE ................................... A137

aHow the Text and Index are organized

: Inventory maintained. s : Inventory maintained in Japan.

Heat-resistant Alloy, Titanium Alloy

Cast Iron (<350MPa)

Stainless Steel (<200HB)

Thickness Corner Radius Chip Breaker

Depth of Cut (inch)

Depth of Cut (inch)

Depth of Cut (inch)

Carbon SteelAlloy Steel (Wiper)

Depth of Cut (inch)

Carbon SteelAlloy Steel

Depth of Cut (inch)

CHIP CONTROL RANGE FOR WORK MATERIALS

*Please refer to page PR9.

CBN & PCD TURNING INSERTS

EXTERNAL TURNING TOOLS

SOLID END MILLS

MILLING TOOL INSERTS

General purpose coated CBN grade for hardened steel

CVD coated grades for steel turning

CBN Breaker Insert

Cermet grade for turning

Breaker for steel turning

Special breakers for difficult-to-cut materials

Double clamp type holder for copying

For multi-task machines HSK tools

^ A040 A047, A050A057

SOLID END MILL

IMPACT MIRACLE end mill Series

IMPACT MIRACLE end mills

^ I143, I146, I147, I151

I152, I174, I176, I177

End mill series for high efficiency machining

2 flute IMPACT MIRACLE

MSTAR end mills

2 flute CBN long neck

Diamond coated end mills

Multi-functional end mills

Face milling cutters with screw-on type inserts

Screw-on insert, shoulder milling cutters

Face milling cutters for high efficiency

Strong edge insert type cutters for cast iron

End mills for deep shoulder milling

Milling cutters for aluminum alloys

Ultra high feed rate radius milling cutters

End mills for titanium alloy milling

Indexable ball nose end Mill for finishing