Documente Academic
Documente Profesional
Documente Cultură
Check valves permit flow in one direction Tilting Disc Check Valves are similar in Features
only and close automatically when flow application to swing check valves. Essen-
reverses. They are entirely automatic in ac- tially, the tilting disc check valve consists of Threaded Ends in accordance with ASME
tion, depending upon differential pressure a cylindrical housing with a pivoted circular B1.20.1.
and velocity of flow within the line to perform disc. The pivots are located just above the
their functions of opening and closing. center of the disc and offset from the plane Flanged Swing Check Valves conform to
of the body seat. This design decreases the applicable requirements of ASME B16.10
The disc and any associated moving parts travel distance of the disc, and the closing in sizes 2" through 24". End flanges on
may be in a constant state of movement if force due to reversal of flow and pressure valves conform to applicable requirements
the velocity pressure is not sufficient to hold differential is reduced by pivot location, of B16.1 for classes 125 and 250.
the disc in a wide open and stable posi- thereby minimizing slam. The seat is of a
tion. Premature wear and noisy operation circular bevel type and the disc pivots in Bronze Trim Valves are for steam, water,
or vibration can be avoided by selecting or out of contact without rubbing or sliding, non-corrosive oil and gas and other fluids
the size of the check valve on the basis of while full pressure differential acts to seal that do not corrode bronze.
flow conditions rather than selecting the the disc tightly after seating.
check valve according to the size of the All Iron Valves are for gases, oils and
pipeline. other fluids not corrosive to iron.
Swing Check Valves with straight-through Valves May Be Installed in horizontal or
Sizing check valves on this basis may often body design and wide hinge support provide vertical pipe lines. In vertical lines, or any
result in the use of valves that are smaller turbulence-free flow and accurate seating. angle from horizontal, they can be used for
than the pipe in which they are used, neces- There is no tendency for seating surfaces upward flow only.
sitating the use of reducers for installation. to gall or score because the disc meets the
The pressure drop will be no greater than flat seat squarely without rubbing. When Lever and Weight can be provided upon
that of a larger valve that is partially open. faster reaction to flow reversal is neces- request to assist disc closure in unusual
Valve life will be greatly extended, and the sary, certain valves can be equipped with flow conditions. 2"-12" Figure 383 come
added bonus, of course, is the lower cost an outside lever and weight. 2" - 12" with standard with an adjustable lever arm
of the smaller valves. lever and weight come with adjustable le- which can be orientated in any position
ver. 14" - 24" valves must be specified for in 15° increments. These valves can be
Each valve in this section is classified by horizontal or vertical orientation. installed in horizontal lines, or in vertical
its pressure rating. lines with upward flow. 14"-24" valves
This will assist the disc to close more must be specified at the time of inquiry and
All swing check valves designated as Class rapidly and reduce the possibility of surge order with the installation orientation for
125 and 250 comply with MSS SP-71 Stan- and shock. horizontal or vertical-upward flow.
dard Practice.
Crane Iron Check Valves have an Non-Asbestos Gaskets and Packings.
identification tag which indicates the
valve catalog number and other pertinent
data. It provides easy and accurate field
reference.
Cap bolts
Cap
Cap gasket Identification
plate
Body Cap bolt nuts
Hinge pin
Hinge
Hinge pin
Disc washer
Disc nut
Disc
Disc
Body seat
ring
Body
Body
30
Iron Body Swing Check Valve Figure 372
31
Figure 373 Iron Body Swing Check Valve
32
Iron Body Swing Check Valve Figure 373 ½
33
Figure 383 Iron Body Swing Check Valve
Class 125 • Bolted Cap • Bronze Trim • Flanged Ends • Lever & Weight
34