Documente Academic
Documente Profesional
Documente Cultură
1
1
]
7
OR
Q. a) Explain the following :
i) Buckinghams Theorem
ii) Geometric similarity
iii) Kinematic similarity
iv) Dynamic similarity 3+2+1+1=7
OR
b) A 1:16 model of subrarine is to be tested in towing tank containing salt water. If the submarine moves at
5 m/sec, at what velocity should the model be towed for dynamic similarity? assume kinematic viscosity
and density for the model and prototype as same. 7 (S-12)
Q. a) State Buckingham's theorem why this theorem is considered superior over the Rayleigh's method
for Dimensional analysis? 6
b) The ratio of lengths of a sub-marine and its model is 30 :1. The speed of submarine (prototype) is 10
m/s . The model is to be tested in a wind tunnel. Find the speed of air in wind tunnel. Also determine the
ratio of drug (resistance) between the model & prototype. Take the value of kinematic viscosities for the
sea water & air as 0.012 stokes and 0.016 stokes resp. The density for sea water and air is given as 1030
kg/m
3
and 1.24 kg/m
3
resp. 7
OR
Q. a) Explain the term Dimensionally homogeneous equation. What are the methods of Dimensional
Analysis ? Describe what do you mean by repeating variables. 6
b) The frictional torque T of a disc of diam D rotating at a speed N in a fluid of viscosity and density in
a turbulent flow is given by
5 2
2
u
T D N
D N
1
]
Prove this by the method of Dimensions. 7
Unit-IV(FP-I)
(W-ll)
Q. a) What is Boundary layer separation ? State various methods of preventing the separation of boundary
layer? 6
b) A flat plate 2m x 2m moves at 50km/hr in stationary air of density 1.15 kg/m
3
. If the coefficient of drag
and lift are 0.75 resp. determine:-(1) The lift force (2) The Drag force (3) The resultant force. 7
OR
Q. a) Explain with neat sketch boundary Layer separation. 6
b) Determine the Drag; Lift and resultant force for a flat plate of size 2m long and 1m wide; on which
experiments were conducted so that the wind flowing at it is at 50 km/hr. The density of air is 1.15 kg/m
3
Coefficient of Drag and lift are 0.75 and 0.15 resp 7
(S-12)
Q. a) Define, explain & draw the figure of following. 6
i) Displacement thickness. ii) Momentum thickness iii) Energy thickness
b) A flat plate 1.5 m x 1.5 m moves at 50 km/hr in stationary air of density 1.15 kg/m
3
, if the coefficient of
drag and Lift are 0.15 and 0.75 resp; determine. i) The lift force, ii) The drag force. iii) The resultant force
iv) The power required to keep the plate in motion. 7
OR
Q. a) What do you mean by the foil terms. 6 i) Boundary layer. ii) Friction & pressure drag, iii) Coefficient
of drag & coefficient of lift.
b) Find the displacement, momentum & energy thickness of the velocity distribution in the boundary layer
given by
2
u y y
U
_ _
, ,
where = Boundary layer thickness. 7
Unit-V (FP-I)
(S-05) Q. (a) What is compound pipe ? How will you determine the equivalent size
of a compound pipe? 4 (b) When a sudden contraction is introduced in a horizontal pipe line from 50 cm
diameter to 25 cm diameter, the pressure changes from 105 KPa to 69 KPa. If coefficient of contraction is
assumed to be 0.65, calculate the water flow rate.
The contraction is subsequently followed by a sudden enlargemenr'from 25 cm diameter to 50 cm
diameter. If the pressure at the 25 cm section is 69 KPa, work out the pressure at 50 cm
enlarged section. 9
OR
126
M EC If III(b) Petrol (s = 0.716)'flows through a 200 mm dia. pipe at the rate of 600 lit/ see. at20C. If the length
of pipe is 1 km, calculate the drop in pressure.: Assume kinematic viscosity as 4 x 10"
3
cmVsec and f =0-013. 7
OR
Q. (a) Derive an expression for loss of head due to sudden expansion in pipe.
6
(b) The rate of flow of water pumped into a pipe line ABC, which is 200 m long is 20 lit/sec. The pipe is laid on
an upward slope of 1 in 40. The length of portion AB is 100 m and its diameter 100 mm, while the length of
portion BC is also 100 mm but its dia. is 200 mm. The change of dia. at B is sudden. The flow is taking place
from A to C, where the press at A is 19-62 N/cm
2
and end C is connected to tank. Find the pressure at C and
draw hydraulic and total energy line. Take f = 0.008. 7
(W-10)
Q. (a) What are the various losses in pipe flow ? Explain in brief. 6
(b) Three pipes of same length L diameter D and friction factor f are connected in parallel. Determine the
diameter of the pipe of Length L and friction factor f which will carry same discharge for the same head loss.
hf =
fLV
2
2gD
Q. (a) Explain in brief hydraulic gradient line and the total energy line.
6
(b) For the distribution main of a city water supply a 0.30 m main is required. As pipes above 0.25 m are not
available, it is decided to lay two parallel mains of same diameter. Find the diameter of the parallel main. 7
Q. (a)
(b)
(s-ti) '---,"
Explain and name all the losses taking place in pipe flow/Write formula related with each loss and explain all
notations used. Explain how these losses are minimised ? 7
In a 80 mm diameter pipeline an oil of specific gravity 0.8 is flowing at the rate of 6.012 m
3
/s, sudden expansion
takes place into a second pipeline of such diameter that maximum pressure rise is obtained. Find: (i) Loss of
energy in sudden expansion
(ii) Difference in mercury level of manometer connected between two pipes. 7 OR
132
Q, (a) Derive Darcy-Weisbach equation for flow through pipe. 7 (b) Three pipes of diameters 300 mm, 200 mm
and 400 mm and lengths 450 m, 255 m and 315m resp. are connected in series. The difference in water levels in
two tanks is 18m. Determine the rate of flow of water if coefficients of friction are 0.0075, 0.0078,0-0072 resp.
considering all minor losses. 7
(W-ll)
Q. a) Explain H.GLand T.E.L sketch. 6 b) Determine the rate of flow of water through a pipe of dia. 20cm and
length 50 cm. One end of the pipe is connected to a reservoir and other end is open to the atmosphere. The pipe
is horizontal and height of the water in the reservoir is 4m above the centre line of pipe. Take F = 0.09. 7
OR
Q. a) State the losses taking place in pipe flow. Write formula related with each loss and explain its notations.
How these losses are minimized ?
6
b) In a 80 mm dia. Pipe line an oil of specific gravity 0.8 is flowing at the rate of 6.012 mVsec, sudden
expansion takes place in to a second pipe line of such dia that maximum pressure rise is obtained, find, i) Loss
of energy in sudden expansion, ii) Difference in mercury level of manometer connected beftwo pipes.
7
(S-12)
Q. a) Derive Darcy Weisbach equation for pipe flow. 6
b) The rate of flow of water through a horizontal pipe is 0.25m
3
/sec the diameter of the pipe which is 200m is
suddenly enlarged to 400 mm the pressure intensity in the smaller pipe is 11.77N/cm
2
Determine i) Loss of
head due to sudden enlargement, ii) Pressure intensity in the large pipe iii) Power lost due to enlargement. 7
OR Q. a) Explain Hydraulic Gradient Line & total energy lines with neat sketch.
6
b) Calculate the rate of flow of water through a pipe of diameter 300mm when the difference of pressure head
between the two ends of a pipe 400mm apart is 5m of water. Assume f=0.009. 7
\it,i ii in1
Q. (a) Show that the force exerted by a Jet of water on an inclined fixed flail
.,,!<.;,, *u_ J:~--..:- .>"
(b)
plate in the direction of Jet is given by F
x
=pav
2
sin
2
9.
Calculate the rate of flow of water for the following data:
i) Diameter of Jet = 50 mm
ii) Angle between plate and Jet = 30.
iii) Force exerted in the direction of Jet = 1471.5 N. 7
(W-1I)
Q. a) Derive an expression for the force exerted by a jet of water on the fixed vertical plate in the direction
of jet. 7
b) A jet of water of diameter 50mm moving with a velo. of 20m/sec strikes a fixed plate in such a way that
the angle between the jet and the plate is 60. Find the force exerted by the jet on the plate, i) In the
direction normal to plate, ii) In the direction of Jet. 7
Q. A Jet of water having a velo. of 15 m/sec strikes a curved vane which is moving with velo. of 5 m/sec
the vane is symmetrical and it is so shaped that the Jet is deflected through 120. Find the angle of Jet at
inlet of vane so that there is no shock. What is the abs. velo.of the Jet at outlet in magnitude and direction
and the work done per unit wt. of water'/Assume vane to be smooth Draw velocity diagram. 14
(S-I2)
Q. a) Show that the force exerted by the jet of water on an inclined fixed
plate in the direction of jet is given by Fx-pav
2
sin
2
6 7 b) A nozzle of 50rnm dia. delivers a stream of water
at 20m/sec perpendicular to a plate that moves away from the jet at 5m/sec find, i) The force on the plate.
ii) Tire work done & iii) The efficiency of jet. 7
OR
Q. a) A jet of water moving at ]2m/sec impings on vane shaped to deflect the jet through 120 when
stationary. If the vane is moving at 5 m/sec , find the angle of jet so that there is no shock at inlet. What is
the absolute velocity of the jet at exit in magnitue & direction and the work done per second per unit wt. of
water striking per second ? Assume that the vane is smooth. 14
ENGINEERING THERMODYNAMICS
Unit-I(ET)
(S-05)
Q. (a) Differentiate between the following: 4 (i) Homogeneous ari8 heterogeneous system, (ii) Heat and
Work.
(b) During the execution of reversible non-flow process work done is -155 kJ. If initial volume is 0.85 m
3
and pressure during process varies as P = (-3 V + 7) bar, where V is in m
3
, find the final volume. 4
(c) Define the following terms :
(i) State (ii)Path (iii) Process (iv) Cycle. 2
(d) What is relation between the system and its surrounding when system is : (i)Adiabatic (ii) Isolated (iii)
Closed. 3
OR
Q. (a) Define:
(i) Quasistatic process, (ii) Reversible process. 4
(b) A vessel of volume 0.2 m
3
contains Nitrogen at 1.01325 bar and 15C If 0.2 kg of Nitrogen is now
pumped into vessel, calculate the new pressure when vessel has returned to its initial temperature. Molar
mass of N
2
is 28 kg/k-mol. - 4
(c) It is proposed to heat 2 liters of water initially at 15C to a temperature of 80C. What time will be
required to achieve this objective if 0.5 kW electric heater has been supplied for this purpose ? It is
presumed that system does not exchange any heat with the surroundings. Take sp.heatofwater = 4.2kJ/kg-
K. 5
(W-05)
Q.(a) State the different between extensive nad intensive properties and state wherther following properties
are intensive or extensive: (i) Pressure (ii) Temperature (iii) Mass (iv) Density. (v) Volume (vi) Surface
area. 6
(b) Four Kmol of gas occupies 273.44m
3
volume at a temperature of
130 C. If the density of the gas under these conditions is 0.644 kg/m',
determine:
__..'If
Q.(a)
(b)
Q-(a)
(b)
MECHANICS OF MATERIALS
(Unit-I)MOM
126
(W-12)
Q. a) Differentiate between the following, giving due explanation;
i) stress and strain.
ii) Lateral strain and longitudinal strain
iii) Tensile stress and compressive stress. 6
b) A steel rod of 20 mm diameter passes centrally through a copper tube 40 mm external diameter and
30mm internal diameter. The tube is closed at each end by rigid plates of negligible thickness. The
nuts are tightened lightly home on the projected parts of the rod. If the temperature of the assembly is
raised to 60C, calculate the stresses developed in the copper and steel. Take E for steel as 2
10
5
N/mm
2
and E for copper as 1 20
5
N/mm
2
. Take a for steel as 12 10
-6
per C and = 18 10
-6
perC for copper. 8
OR
Q. a) Prove that the volumetric strain of a cylindrical rod which is subjected to an axial tensile load is
equal to strain in the length minus twice the strain of diameter. 6
b) A member ABCD is subjected to point loads P
1
P
2
P
3
P
4
as shown in figure and calculate the force
P
3
necessary for equilibrium if P
1
= 120kN, P
2
=220 kN and P
4
=160kN. Determine also the change in
the length of the member. Take E = 2 10
5
N/mm
2
.
(S-13)
Q. a) Define the following terms:
i) Modulus of Elasticity
ii) Bulk Modulus
iii) Modulus of Rigidity. .6
b) A compound bar consist of a circular rod of steel of diameter 25 mm rigidly fitted into a copper
tube of internal diameter 25 mm and thickness 5 mm. If the bar is subjected to a load of 120 kN. Find
the stresses developed in two materials. Take E
s
= 2 10
5
N/mm
2
and E
c
= 1.05 10
5
N/mm
2
. 8
OR
Q. a) A rod of steel is 20 m long at a temp, of 20 C. Find the free expansion of the length when temp,
is raised to 85 C. Find the temperature stress produced:
i) when the expansion of the rod is prevented,
ii) when the rod is permitted to expand by 6.0 mm
Take = 12 10
-6
/C and E = 200 GN/m
2
9
b) Explain the stress-strain curve for a mild steel bar. 5
(Unit-II)MOM
(W-12)
Q. a) Derive the relation between loading intensity, shear force and bending moment. 5
b) Draw shear force and bending moment diagrams for the cantilever beam shown in figure.
OR
b) A closely coiled helical spring of round steel wire 13 mm in diameter having 10 complete turns with
mean diameter of 140 mm is subjected to an axial load of 220 N. Determine:
i) The deflection of spring
ii) Maximum shear stress in the wire
iii) Stiffness of spring. (Take, C = 8 10
4
N/mm
2
). 6
(Unit-IV)MOM
(W-12)
Q. a) Derive the expressions for circumferential and longitudinal stresses in a thin cylinder closed at both
ends and subjected to internal fluid pressure. 6
b) A thin spherical shell of internal diameter 1.5 m and of thickness 8 mm is subjected to an internal
pressure of 2 N/mm
2
Determine the increase in diameter and increase in volume. Take E = 2 10
5
N/mm
2
and Poisson's ratio = 0.3. 8
OR
Q. a) Differentiate between a thin cylinder and a thick cylinder Name the stresses set up in a thick cylinder
subjected to internal fluid pressure. 5
b) A thin cylindrical shell 1000 mm long, 200mm internal diameter having thickness of metal as 10 mm is
filled with fluid at atmospheric pressure If an additional 20,000 mm
3
of fluid is pumped into the cylinder,
find
i) The pressure exerted by the fluid on the cylinder.
ii) The hoop stress induced. Take E= 2 10
5
N/mm
2
and Poisson's ratio =0.3 9
(S-13)
Q. a) Derive expression from first principles for circumferential and longitudinal stresses in a thin cylinder
subjected to internal pressure. 7
b) A thick cylindrical shell with 300 mm outer diameter and 200 mm internal diameter is subjected to an
internal pressure of 10 N/mm
2
. Determine the minimum external pressure that can be applied so that tensile
stress in the metal does not exceed 15 N/mm
2
. 7
OR
Q. a) A cylindrical shell is 3 m long, 1 m in diameter, and the thickness of metal is 10 mm. It is subjected
to an internal pressure of 150 N/cm
2
.
Calculate the change in dimensions of the shell and the maximum
intensity of shear stress induced. Take, E = 200 GPa and = 0.3. 7
b) A cylinder of 120 mm internal diameter to an internal fluid pressure of 80 N/mm
2
. If the maximum
stress developed in the cylinder is not to exceed 70 N/mm
2
. Find the thickness of thick cylinder. 7
(Unit-V)MOM
(W-12)
Q. a) Prove that the maximum stress induced in a body due to suddenly applied load is twice the stress
induced when the same load is applied gradually. 5
b) An unknown weight falls through a height of 20 mm on a collar rigidly attached to the lower end of a
vertical bar 5m long and 800 mm
2
in section. If the maximum extension of the rod is to be 0.5mm, what is
the corresponding stress and magnitude of the unknown weight ? Take E = 2 10
5
N/mm
2
8
OR
Q. a) Define the following terms
i) Principal planes
ii) Principal stresses
iii) Obliquity
iv) Mohr's circle. 4
b) At a certain point in a strained material, the stresses on two planes, at right angles to each other are
20N/mm
2
and 10 N/mm
2
both tensile. They are accompanied by a shear stresses of magnitude 10 N/mm
2
.
Find graphically or otherwise the location of principal planes and evaluate the principal stresses. 9
(S-13)
Q. a) Show that strain energy under uniaxial tension stored by a member per unit volume
2
2E
b) A rectangular block of material is subjected to a tensile stress of 110 N/mm
2
on one plane and a tensile
stress of 47 N/mm
2
on a plane at right angle, together with shear stress of 63 N/mm
2
on the same planes,
find:
i) The direction of the principal planes
ii) The magnitude of the principal stress
iii) The magnitude of the greatest shear stress. 8
OR
Q. a) The principal stresses at a point in a bar are 200 N/mm
2
(tensile) and 100 N/mm
2
(compressive).
Determine the resultant stress in magnitude and direction on a plane inclined at 60to the axis of the major
principal stress. Also determine the maximum shear stress in the material at the point. 6
b) A weight of 1.5 kN is dropped on a collar attached at the lower end of a vertical bar 4 m long and 30
mm in dia. Calculate the height of drop if the maximum instantaneous stress is not to exceed 120 N/mm
2
Also calculate the instantaneous elongation. Take E = 2 10
5
N/mm
2
. 7
(Unit-VI) MOM
(W-12)
Q. a) Prove that the deflection at the centre of a simply supported beam carrying a point load at the centre
is given by Yc =
3
48
WL
EI
where W = point load, L= Length of beam. 6
b) A beam of uniform rectangular section 100 mm wide and 100 mm deep is simply supported at its ends.
It carries a uniformly distributed load of 10 kN/m run over the entire span of 4M. Find
i) Slope at the supports.
ii) Max. deflection. Take E = 1 10
4
N/mm
2
7
OR
Q. a) A simply supported beam of span 6 m is loaded as shown in Fig. Determine
i) Slope at the end A.
ii) Deflection at load point C.
iii) Deflection at point D.
iv) Maximum deflection. Take flexural rigidity EI = 15 10
9
KN-mm
2
13
(S-13)
Q. a) Calculate Maximum deflection and slope, for a simply supported beam of span 'l' m having point
load at mid of the span. 5
b) A simply supported beam of 3m span carries a point loads of 120 kN and 80 kN at a distance of 0.6 m
and 2 m respectively from the left hand support. If I for the beam = 16 10
8
mm
4
and E = 210 GN/m
2
, find
the deflection under loads. Also calculate maximum deflection. 8
OR
Q. a) Calculate the deflection at point C and D. Also calculate the maximum deflection for a given Fig. by
Macaulay's method. Take, E = 200 GN/m
2
and I = 20 10
7
mm
4
. 13
FLUID POWER-I
(Unit-I) FP-I
(W-12) Q.(a) Differentiate between :-
(i) Absolute and guage pressure.
(ii) Simple manometers and differential manometer.
Oil") Piezometer and pressure guages. 6
(b) Determine the total pressure on a circular plate of diameter 2m which is placed vertically in a water in
such a way that the centre of plate is 3 m below the free surface of water. Find position of centre of
pressure also. 7
OR
Q.(a) Explain the phenomenon of capillarity. Obtain an expression for capillary rise of a liquid. 4
(b) Explain the following Newtonian and NonNewtonian fluids,
vapour pressure and compressibility. 6
(c) The capillm y rim- in a ^lass tube is not to exceed 0.2 mm of water. Determine llN minimum si/c, ^iven
that surface tension for water in conlncl with nil ~ (1,07; 1 N/m. 3
232
MECH III
MECII III
233, principal stress. Also determine the maximum shear stress in the material at the point. 6
(b) A weight of 1.5 kN is dropped on a collar attached at the lower end of a vertical bar 4 m long and
30 mm in dia. Calculate the height of drop if the maximum instantaneous stress is not to exceed 120
N/mm
2
Also calculate the instantaneous elongation. TakeE=2xl0
5
N/mm
2
. 7
(Unit-VI) MOM
Q. (a)
(b)
Q.
Q-(a)
(b)
Q.
(W-12)
Prove that the deflection at the centre of a simply supported beam
carrying a point load at the centre is given by Yc =
WL
3
48 El
13
where W = point load, L= Length of beam. 6
A beam of uniform rectangular section 100 mm wide and 100 mm deep is simply supported at its
ends. It carries a uniformly distributed load of 10 kN/m run over the entire span of 4M. Find-(i) Slope
at the supports. (ii) Max. deflection. TakeE=lxl0
4
N/mm
2
7
OR
A simply supported beam of span 6 m is loaded as shown in [Fig.Q.12] Determine
(i) Slope at the end A. (ii) Deflection at load point C. (iii) Deflection at point D. (iv) Maximum
deflection. Take flexural rigidity EI= 15xl0
9
KN-mm
2
(S-13)
Calculate Maximum deflection and slope, for a simply supported beam of span '/' m having point load
at mid of the span. 5
A simply supported beam of 3m span carries a point loads of 120 kN and 80 kN at a distance of 0.6 m
and 2 m respectively from the left hand support. If I for the beam =16xl0
8
mm
4
andE = 210 GN/m
2
,
find the deflection under loads. Also calculate maximum deflection.
8
OR
Calculate the deflection at point C and D. Also calculate the maximum deflection for a given Fig. Q.
12 by Macaulay's method. Take, E = 200GN/m
2
and I = 20xl0
7
mm
4
. 13
5 KN/m
2KN.m
B
3m
2.5m
1.5m
Fig Q 12
FLUID POWER-I
(Unit-I)FP-I
(W-12) Q. (a) Differentiate between:-
(i) Absolute and guage pressure.
(ii) Simple manometers and differential manometer.
(iii) Piezometer and pressure guages. 6
(b) Determine the total pressure on a circular plate of diameter 2m which is placed vertically in a
water in such a way that the centre of plate is 3 m below the free surface of water. Find position of
centre of pressure also. 7
OR
Q.(a) Explain the phenomenon of capillarity. Obtain an expression for capillary rise of a liquid. 4
(b) Explain the following Newtonian andNonNewtonian fluids,
vapour pressure and compressibility. 6
(c) The capillary rise in a glass tube is not to exceed 0.2 mm of water. Determine its minimum size,
given that surface tension for water in contact with air = 0.0725 N/m. 3
232
MECH III
MECH HI
233(S-13)
Q. (a) Explain with neat sketch the following :-(i) U tube differential manometer
(ii) Total pressure on a vertical plane surface submerged in liquid. 6
(b) The dynamic viscosity of an oil, used for lubrication between a shaft and sleeve is 6 poise. The shaft is
of diameter 0.4 m and rotates at 190 rpm. Calculate the power lost in the bearing for a sleeve length of 90
mm. The thickness of oil film is 1.5 mm. 7
OR
Q. (a) Differentiate between: (i) Liquid and gases (ii) Real fluid and ideal fluid (iii) Specific weight and
specific volume of fluid. 6
(b) Derive an expression for the depth of centre of pressure from free surface of liquid of an inclined plane
surface submerged in the liquid. 7
(Umt-II)FP-I
(W-12)
Q. (a) What is "Metacentre" and "Metacentric height". Derive an
expression for the metacentric height of a floating body. 7
(b) A jet of water from a 25 mm diameter nozzle is directed vertically upwards. Assuming that the jet
remains circular and neglecting any loss of energy, that will be the diameter at a point 4.5 m above the
nozzle, if the velocity with which the jet leaves the nozzle is 12m/s. 6
OR
Q. (a) Define velocity potential function and stream function. 4
(b) What is venturimeter? Derive an expression for the discharge through a venturimeter. 6
(c) A fluid field is given by: V = x
2
yi +y
2
zj - (2xyz+yz
2
) k
Prove that it is a case of possible steady incompressible fluid flows. Calculate the velocity and acceleration
at the point (2, 1,3)
3
(S-13)
Q. (a) State different types of flow lines with sketches. 6
(b) A pipeline carrying oil of specific gravity 0. 87, changes in diameter from 200 mm. diameter at a
position A to 500 mm diameter at a position B which is 4m at a higher level. If the pressure at A& B are
9.81 N / cm
2
and 5.886 N/cm
2
respectively and the discharge is 200 liters/s. Determine the loss of head and
direction of flow, 7
OR Q. (a) What is Euler's equation of motion? Also derive Bernoulli's
equation from Euler's equation. 6
(b) A horizontal venturimeter with inlet diameter 20 cm and throat diameter 10 cm is used to measure the
flow of water. The pressure at inlet is 17. 658 N/cm
2
and the vacuum pressure at the throat is 30 cm of
mercury. Find the discharge of water through venturimeter. Take C
d
= 0.98. 7
(Unit-Ill) FP-I
Q. (a)
. (W-12)
Define the following non-diamensional numbers Reynold's number, Froude's number and mach number.
What are their sign ificances for fluid flow problems ? 7 (b) Using Buckingham's n -theorem, show that the
velocity through a circular arifice is given by
234
MECH HI
where, Ft is the head causing flow,
D is diameter of the orifice,
^ is coefficient of viscosity
i is the mass density and
g is acceleration due to gravity. . 7
OR Q. (a) State various methods of diamentional analysis. Describe
Reyleigh's method for diamensional analysis. 7 (b) Find an expression for the drag force on smooth sphere
of
diameter D, moving with a uniform velocity V in a fluid flow of
density g and dynamic viscosity |^. 7 I MECH in 23JQ.(a)
(b)
Q. (a)
(b)
Q. (a)
(b)
Q.(a)
(S-13)
Define the following dimensionless numbers :-(i) Reynold's number (ii) Mach's number (iii) Froude's
number (iv) Weber's number.
8
Find an expression for the drag force on smooth sphere of diameter D, moving with a uniform velocity V
in a fluid of density p and dynamic viscosity JJ,. 6
OR
What are different similarities that can exist between model and prototype ? 6
A ship 300 m long moves in sea water, whose density is 1030 kg/m
3
. Al : 100 model of this ship is to be
tested in a wind tunnel. The velocity of air in the wind tunnel around the model is 30 m/s and the resistance
of the model is 60 N. Determine the velocity of ship in sea water and also the resistance of the ship in sea
water. The density of air is given as 1.24 kg/m
3
. Take the kinematic viscosity of sea water and air as 0.012
stokes and 0.018 stokes respectively. 8
(Unit-IV)FP-I
(W-12)
Define displacement thickness. Derive an expression for the displacement thickness.
Air is flowing over a flat plate 500 mm long and 600 mm wide
with a velocity of 4 m/s. The kinematic viscosity of air is
giyenas 0.15xl0
4
m
2
/S. Find
(i) The boundry layer thickness at the end of the plate.
(ii) Shear stress at 200 mm from the leading edge and
(iii) Drag force on one side of the plate.
Take the velocity profile over the plate as -
U
5;
and density air 1.24 kg/m
3
OR
What do you mean by separation of boundry layer ? What is the effect of pressure gradient on boundry
layer separation?
(b) For the velocity profile for turbulent boundry layer.
~
=
(y /) obtain an expression for boundry layer thickness, shear stress, drag force on one side of the
plate and coefficient of drag in terms of Reynold number. Given the shear stress (T
O
) for
the turbulent boundry layer as *o - 0.0225 U
(S-13)
Q. (a) For a real fluid flow over a flat plate, explain momentum thickness and deduce a relation for
momentum thickness. 6
(b)
Air is flowing over a smooth plate with a velocity of 10 m/s. The length of plate is 1.2m and width 0.8m. If
laminar boundary layer exists up to a value of Re = 2 x 10
5
, find the maximum distance from the leading
edge upto which laminar boundary layer exists. Find the maximum thickness of laminar boundary layer if
the velocity profile is given by
u .
Take kinematic viscosity for air = 0. 15 stokes. 7
OR
Q. (a) What is drag and lift? Also explain with neat sketch coeffi cient of drag and lift.
(b) The velocity distribution in the boundary layer is given by
U 5
where u is the velocity at distance y from plate and u = U at y = 8, 6 being boundary layer thickness.
Find:
(i) The displacement, momentum and energy thickness.
5*
*!
(ii) Value of
9
236
MECH III(Unit-V)FP-I
(Unit-VI)FP-I
(W-12)
Q. (a) Show that loss of head due to sudden expansion in pipeline is a function of velocity head. 6
(b) At a sudden enlargement of a water main from 240 mm to 480rrm diameter, the hydraulic gradient rises
by 10 mm. Estimate the rate of flow. 7
OR Q.. (a) Explain the phenomenon of water Hammer. Obtain an expression
for the rise of pressure when the flowing water in pipe is brought to rest by closing the valve gradually. 6
(b) A pipe line 300 mm in diameter and 3200 m long is used to pump up 50 kg per second of an oil whose
density is 950 kg/m
3
and whose kinematic viscosity is 2.1 stokes. The centre of the pipeline at the upper
end is 40 m above than that at the lower end. The discharge at the upper end is atmospheric. Find the
pressure at the lower end and draw the hydraulic gradient and the total energy line. 6
*
(S-13)
Q. (a) Derive an expression for loss of head due to sudden contrac tionin pipe. 7
(b) A pipeline 60 cm diameter bifurcates at a Y junction into two branches 40cm and 3 Ocm in diameter. If
the rate of flow in the main pipe is 1.5m'/s and mean velocity of flow in 30cm diameter pipe is 7.5 m/s,
determine the rate of flow in the 40 cm diameter pipe. 7
OR
Q. (a) What do you mean by water hammer? Explain factors affecting water hammer. Also discuss various
cases of water hammer. 6
(b) A horizontal pipeline 50 m long is connected to a water tank at one end and discharged freely into the
atmosphere at the other end. For the first 30 m of its length from the tank, the pipe is 200 mm diameter and
its diameter is suddenly enlarged to 400 mm. The height of water level in the tank is 10m above the centre
of the pipe. Considering all minor losses, determine the rate of flow. Take f = 0.01 for both sections of
pipe. Also draw HGL and TEL.
8
(W-12)
Show that the force exerted by a jet of water on moving inclined plate in the direction of jet is given by Fx
= /a(v-u)
2
sin
2
# where, a = area of jet
(b)
Q-(a)
(b)
Q.(a)
(b)
0= Inclination of the plate with the jet
v= Velocity of jet 7
A jet of water of diameter 50 mm moving with a velocity of 40 m/s strikes a curved fixed symmetrical
plate at the centre Find the force exerted by the jet of water in the direction of the jet, if the jet is deflected
through an angle of 120 at the outlet of the curved plate. 7
OR
Show that the efficiency of free jet striking normally on a series of flat plates mounted on the periphery of
a wheel can never exceed 50%. 7
A jet of water having a velocity of 3 5 m/s impinges on a series of vanes moving with a velocity of 20 m/s.
The jet makes an angle of 30 to the direction of motion of vanes when entering and leaves at an angle of
120. Draw the triangles of velocities at inlet and outlet and find (i) The angle of vanes tips so that water
enters and leaves
without shock.
(ii) The work done per unit weight of water entering the vane and (iii) The efficiency. 7
Define:- (i) (u) (iii)
(S-13)
Hydraulic efficiency Mechanical efficiency Volumetric efficiency.
6
A jet of water of diameter 50 mm moving with a velocity of 20 m/sec strikes a fixed plate in such a way
that the angle between the jet and the plate is 60. Find the force exerted by the jet on one plate-(i) in the
direction normal to the plate
(ii) in the direction of jet. 7
238
MECH HI
239OR
Q. A jet of water moving at 18 m/s impinges on vane shaped to deflect the jet through 120 when
stationary. If the vane is moving at 8 m/s, find the angle of jet so that there is no shock at inlet. What is the
absolute velocity of the jet at exit in magnitude and direction and the work done per second per unit wt.of
water striking per second? Assume the vane is smooth.Draw velocity diagram . 13
ENGINEERING THERMODYNAMICS
(Unit-I)ET
(W-12)
Q. (a) Define the terms State, Property, Process and Cycle of a
thermodynamic system. 4
(b) A car has a mass of 1600 kg. It has an engine which develops 35 kW when travelling at a speed of 70
km/h. Neglecting losses; determine the resistance to the motion in N/kg* 5
(c) Define the characteristic gas constant. How does it differ from
universal gas constant? Write the ideal gas equation associated with these constant and units of these
constant. 4
OR
Q. (a) An oxygen cylinder has a capacity of 300 liters and contains oxygen at a pressure of 3.1 MN/m
2
and
temperature 18C The stop valve is opened and some gas is used. If the pressure and temperature of the
oxygen left in the cylinder fall to 1.7 MN/m
2
and 15C, respectively, determine the mass of oxygen used.
The density of oxygen at 0Cand 1.01325 bar may be taken as 1.429kg/m
3
. 5
(b) How does classical thermodynamics differ from statistical thermodynamics? 4
(c) State the difference between extensive, intensive and specific properties of a thermodynamic system.
Give three examples of each. 4
"240 ^______________________
:
_______MECHIH
(S-13) Q. (a) What do you understand by macroscopic and microscopic
viewpoint? 4 (b) An automobile vehicle of 1500 kg mass is running at a speed of 60 km/hr. The brakes are
applied and the vehicle is brought to rest. Calculate the rise in temperature of the brakes if their mass is 15
kg. Take specific heat of the brake material = 0 .46 kJ/kg. K
4
(c) Define the law that forms the basis for temperature measure ment. Establish the correlation between
Centigrade and Fahrenheit temperature scale. 2 + 3 = 5
OR
Q. (a) Two spheres, each of capacity 2 m
3
, are connected by pipe with valve inserted in between. When the
valve lies in a closed position one sphere contains oxygen at 50 KPa and 320 K and other contains oxygen
at 45 KPa and 290 K. Subse quently the valve is opened and the entire system is allowed to attain the
equilibrium. At this state the final temp, is noted to be 27C. Presuming that the volume of connecting pipe
is negligible, determine final pressure of the complete system. (M for0
2
=32). 5
(b) State the concept of temperature and equality of temperature . 3
(c) State giving brief justification, whether the following proper ties of system are intensive or extensive :
Viscosity , I'lilltnlpv. Pressure, specific volume, density, surface nrcn. vHoi ily Differentiate between
intensive and extensive pmpeilit-M
1 i }-
(Unit-II)ET
(W-12)
Q. (a) A gas is compressed hyperbolically from a pressure and volume of 100 KN/m
2
and 0.056 m
3
,
respectively, to a volume of 0.007m
3
.' Determine the final pressure and the work done on the gas. 3
(b) Prove that heat transferred in polytropic process for a closed system is given by Q = mc
n
(T,-T
2
) Joules,
where c
n
is polytropic
heat capacity given byC
v
. (y-n)/(n-l). 5
(c) A gas has a density of 1.875 kg/m
3
at a pressure of 1 bar and with a temperature of 15C. Amass of 0.9
kg of gas requires a heat transfer of 175 kJ to raise its temperature from 15C to 250C while
MECH IN
241