Documente Academic
Documente Profesional
Documente Cultură
1
I B.Tech Supplimentary Examinations, Aug/Sep 2007
INTRODUCTION TO CHEMICAL ENGINEERING
(Chemical Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
(a) Filtration
(b) Flotation. [8+8]
2. (a) What is the use of making a material balance and an energy balance?
(b) Write about the principle of conservation of mass and give the steps involved
in making mass balance calculations. [4+12]
3. Obtain Bernoulli’s equation from mechanical energy balance for steady flow. [16]
4. Derive the expression for log mean temperature difference for parallel flow heat
exchanger. What are the conditions under which it is valid? [16]
5. (a) Write the relation between individual and overall mass transfer coefficients
and also mention units of each.
(b) Briefly explain design of packed adsorption column. [6+10]
6. (a) Explain plate efficiency. What are different types of plate efficiencies?
(b) Write on any two of the following: [6+10]
i. Flash distillation
ii. Steam distillation
iii. Azeotropic distillation.
7. Discuss about the following terms for gas-liquid mass transfer operations: [16]
(a) Weeping
(b) Entrainment
(c) Hold-up
(d) Axial mixing.
1 of 2
Code No: R05010803 Set No. 1
(b) Write about the construction and operation of tray dryers with a neat diagram.
Mention its uses and advantages. [8+8]
⋆⋆⋆⋆⋆
2 of 2
Code No: R05010803 Set No. 2
I B.Tech Supplimentary Examinations, Aug/Sep 2007
INTRODUCTION TO CHEMICAL ENGINEERING
(Chemical Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. (a) Define fundamental units and dimensions useful in chemical engineering, write
dimensional formulae for Force and Energy.
(b) Define the units of major eight (8) quantities used in SI system.
(c) Explain the basis of dimensional analysis. [4+8+4]
2. (a) Write the energy balance equation for the following: [4×2=8]
i. Non-flow process
ii. Non-flow process at constant volume
iii. Non-flow process at constant pressure
iv. Flow system.
(b) Give the steps to be followed in making energy balance calculations. [8]
5. (a) The equilibrium in vapor-liquid systems is governed by the phase rule. Discuss.
(b) What are boiling point diagrams? Explain with a neat figure. [6+10]
7. (a) What are the two main categories into which industrial liquid-liquid contactors
are classified? Discuss about each category.
(b) Describe the construction and working of a rotating disc contactor. Where is
it used and what are its advantages? [6+10]
1 of 2
Code No: R05010803 Set No. 2
8. Describe the construction and operation of tray dryers and rotary dryers with neat
diagrams. Mention their uses and advantages. [16]
⋆⋆⋆⋆⋆
2 of 2
Code No: R05010803 Set No. 3
I B.Tech Supplimentary Examinations, Aug/Sep 2007
INTRODUCTION TO CHEMICAL ENGINEERING
(Chemical Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
(a) Screening
(b) Size reduction. [8+8]
3. The total energy content of a fluid element in motion has several components.
Discuss in detail and obtain the total energy balance for steady flow. [16]
4. (a) Explain heat conduction through a composite plane wall with a neat figure.
Also, derive the equation for the rate of heat transfer.
(b) The mean area for heat transfer depends on the shape of the solid. State the
different ways in which it can be expressed for different shapes of solids.
[10+6]
5. (a) Name two mass transfer operations for the following phases in contact:
i. liquid-liquid
ii. solid-vapor.
(b) Mention the similarities between various mass transfer operations.
(c) Many differences exist between various mass transfer operations. Explain with
examples. [8+4+4]
6. (a) Explain plate efficiency. What are different types of plate efficiencies?
(b) Write on any two of the following: [6+10]
i. Flash distillation
ii. Steam distillation
iii. Azeotropic distillation.
7. (a) Define the following terms with respect to gas-liquid mass transfer operations:
i. Cross flow
ii. Dual flow
iii. Split flow
1 of 2
Code No: R05010803 Set No. 3
iv. Turndown ratio. [4×2=8]
(b) Explain the following terms and give their effect on the gas-liquid mass transfer
operation:
i. Entrainment
ii. Weeping. [4+4]
8. (a) What is an adsorption isotherm? What information can be obtained from it?
Mention other ways of representing equilibrium adsorption data.
(b) What are the desirable characteristics of adsorbents? Give at least four ex-
amples of adsorbents widely used.
(c) Differentiate between regeneration and reactivation of adsorbents. [6+6+4]
⋆⋆⋆⋆⋆
2 of 2
Code No: R05010803 Set No. 4
I B.Tech Supplimentary Examinations, Aug/Sep 2007
INTRODUCTION TO CHEMICAL ENGINEERING
(Chemical Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
⋆⋆⋆⋆⋆
1 of 1