Documente Academic
Documente Profesional
Documente Cultură
Trademarks
Windows 95/98/Me and Windows NT/2000/XP/VISTA are registered trademarks of
Microsoft Corp. All other brands and product names are trademarks of their
respective companies.
Copyright
Copyright 2007 by DSE(NZ)Ltd - all rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the
prior written permission of DSE(NZ)Ltd.
Disclaimer
DSE(NZ)Ltd makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Any software described in this
manual is sold or licensed "as is". Should the programs prove defective following
their purchase, the buyer (and not DSE(NZ)Ltd, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, DSE(NZ)Ltd reserves
the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
Manual Versions
2
XH9948 – DSE WLAN 802.11g 4-Port Router
Table of Contents
1 INTRODUCTION................................................................................................. 4
1.1 PACKAGE CONTENTS ...................................................................................... 4
1.2 SYSTEM REQUIREMENTS................................................................................. 4
1.3 FEATURES & SPECIFICATIONS ......................................................................... 4
2 GETTING TO KNOW THE ROUTER.................................................................. 6
2.1 THE FRONT PANEL ......................................................................................... 6
2.2 REAR PANEL .................................................................................................. 6
3 SOFTWARE........................................................................................................ 8
3.1 DRIVER CD CONTENTS ................................................................................... 8
4 INSTALLATION INSTRUCTIONS ...................................................................... 9
4.1 CONNECTING THE ROUTER.............................................................................. 9
5 NETWORKING SETTINGS .............................................................................. 10
5.1 TCP/IP CONFIGURATION FOR W INDOWS 98 ................................................... 10
5.2 TCP/IP CONFIGURATION FOR W INDOWS 2000 ............................................... 13
5.3 TCP/IP CONFIGURATION FOR W INDOWS XP .................................................. 15
5.4 TCP/IP CONFIGURATION FOR W INDOWS VISTA............................................. 17
6 QUICK INSTALLATION GUIDE ....................................................................... 21
7 CONFIGURING THE ROUTER ........................................................................ 26
7.1 STATUS ....................................................................................................... 26
7.2 NETWORK .................................................................................................... 27
7.2.1 LAN..................................................................................................... 27
7.2.2 WAN ................................................................................................... 27
7.2.3 MAC Clone ......................................................................................... 28
7.3 WIRELESS ................................................................................................... 29
7.3.1 Wireless Settings ................................................................................ 29
7.4 FORWARDING (NAT) .................................................................................... 32
7.4.1 Virtual Servers .................................................................................... 32
7.4.2 DMZ .................................................................................................... 34
7.5 SYSTEM TOOLS ............................................................................................ 35
7.5.1 Firmware Upgrade .............................................................................. 35
7.5.2 Factory Defaults.................................................................................. 36
7.5.3 Reboot ................................................................................................ 36
7.5.4 Password ............................................................................................ 37
8 GLOSSARY ...................................................................................................... 38
9 APPENDIX........................................................................................................ 40
9.1 ROUTER DEFAULT SETTINGS ......................................................................... 40
9.2 MY SETTINGS............................................................................................... 40
10 SUPPORT ..................................................................................................... 41
11 WARRANTY.................................................................................................. 41
3
1 Introduction
Thank you for purchasing the DSE XH9948 WLAN 802.11g 4-Port Router, this
Router is designed to offer a complete wireless solution that allows you to share an
Internet connection, files, or network resource while protecting your network using
enhanced security features.
Note: This device is not a modem. In order to share internet connection you need
need to have subscription to an existing broadband service via an Ethernet based
Broadband Modem, USB-only modems are not supported by this device.
Features:
• Wi-Fi compliant with IEEE 802.11b and 802.11g devices
• Adopts eXtended RangeTM WLAN transmission technologies
• Integrate 4 port Fast Ethernet switch: 10/100Mbps MDI/MDIX auto-sensing
4
XH9948 – DSE WLAN 802.11g 4-Port Router
• Provide 10/100Mps WAN interface to connect with DSL or cable modem
for broadband Internet access
• Browser-based interface configuration and management makes the device
OS independent, easy to set up and simple to install
• Built-in firewall
Specifications:
General
Standards IEEE 802.3, 802.3u, 802.11b and 802.11g
Protocols TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP
Ports One 10/100M Auto-Negotiation WAN RJ45 port, Four
10/100M Auto-Negotiation LAN RJ45 ports supporting
Auto MDI/MDIX
Cabling Type 10BASE-T: UTP category 3, 4, 5 cable (max 100m)
EIA/TIA-568 100 STP (max 100m)
100BASE-TX: UTP category 5, 5e cable (max 100m)
EIA/TIA-568 100 STP (max 100m)
Radio Data Rate 54/48/36/24/18/12/9/6Mbps or 11/5.5/3/2/1Mbps
Radio Frequency 2.4GHz Spectrum
Power Supply 9V~ 0.8A
LEDs Power, System, WLAN, Link/Act
Safety & Emissions FCC, CE
Environmental and Physical
Operating Temp. 0°C~40°C (32°F ~104°F)
Operating Humidity 10% - 95% RH, Non-condensing
Dimensions (W×D×H) 150×118×30 mm (without antenna)
5
2 Getting to know the Router
The rear panel contains the following features (Viewed from left to right):
• Wireless antenna
• Reset button (Factory Default settings)
6
XH9948 – DSE WLAN 802.11g 4-Port Router
• WAN RJ45 port for connecting the router to an ADSL, cable modem or to
Ethernet
• Four LAN 10/100Mbps RJ45 ports for connecting the router to the local
PCs
• AC power socket:
Note: Only use the power adapter supplied with the XH9948 54Mbps Wireless
Router, use of a different adapter may result in product damage.
7
3 Software
!"# $ % % %
& ' % ()
% #$% % *
+,- %%
. %/ %
# $% 0 %%
1 ' 2 34
% 5% 67 %'
"
& %/ * ) 8
77 ' 7
' % '%
9# $ % * +,- % :% 8
% %
& %/ *
'% 7 % '
% + 198
# $% * +,- % :% 8 %
%
! ! %/ ,
' % *, $ 98 %
% ' ;( % $%
* +,- % :% 8 %
8
XH9948 – DSE WLAN 802.11g 4-Port Router
4 Installation Instructions
Note: For initial configuration please use a wired connection to one of the four
ethernet connections (LAN) on the router. Configuration through a wireless
connection is not recommended for any brand of router or wireless card adapter
1. Locate an optimum location for the router. For best wireless coverage, the
best location is typically near the centre of the wireless usage radius or for
optimum result, the closest to the location where wireless devices will be used
the most. However, this will depend on the maximum distance that you can be
away from the broadband modem.
2. Adjust the orientation of the antenna. Normally, upright is a good orientation.
3. Connect the PC(s) and each Network Switch (if required) on the LAN to the
LAN Ports on the router
4. Connect the Broadband Modem to the WAN port on the router
5. Connect the AC power adapter to the AC power socket on the router, and the
other end into an electrical outlet. The router will start automatically. However,
it may need to be configured further to work correctly with your Broadband
modem
9
5 Networking Settings
Note: The default IP address of the XH9948 DSE WLAN 802.11g 4-Port Router is
192.168.0.2, and the default Subnet Mask is 255.255.255.0. The DHCP server is on
by default. The following configuration examples are based on these settings
10
XH9948 – DSE WLAN 802.11g 4-Port Router
11
B. Configure IP Manually – See steps below.
12
XH9948 – DSE WLAN 802.11g 4-Port Router
5.2 TCP/IP Configuration for Windows 2000
Use the following steps to configure the manager PC to be a DHCP client. These
same steps must be performed for every host PC on your network if you use the
DHCP function of the Router.
1. Click the Start button and choose Settings and then Control Panel.
2. Double click the Network and Dial-up Connections icon.
3. Right-click on your network connection and select Properties from the drop
down menu. Select the TCP/IP line and click Properties.
A. Get an IP address from the Router (DHCP) – Make sure that you have the
same settings as shown in the following screen.
13
B. Configure IP Manually – Select Use the following IP address. The default IP
address of the Router is 192.168.0.2. So please use 192.168.0.X (where X is
between 1 and 253, except 2) for the IP Address field, 255.255.255.0 for the
Subnet Mask field and 192.168.0.2 for the Default Gateway field as shown
below. Enter the DNS values as provided by your ISP.
14
XH9948 – DSE WLAN 802.11g 4-Port Router
5.3 TCP/IP Configuration for Windows XP
Use the following steps to configure the manager PC to be a DHCP client. These
same steps must be performed for every host PC on your network if you use the
DHCP function of the Router.
1. Click the Start button and choose Settings and then Control Panel.
2. Double click the Network Connections icon.
3. Right-click on your network connection and select Properties from the drop
down menu. On the General tab, select the TCP/IP line and click Properties.
4. You have two setting methods:
A. Get an IP address from the Router (DHCP) – Make sure that you have the
same settings as shown in the following 2 screens.
15
B. Configure IP Manually – Select Use the following IP address. The
default IP address of the Router is 192.168.0.2. So please use
192.168.0.X (where X is between 1 and 253, except 2) for the IP Address
field, 255.255.255.0 for the Subnet Mask field and 192.168.1.2 for the
Default Gateway field as shown below. Enter the DNS values which are
provided by your ISP. (e.g. 203.96.152.4 / 203.96.152.12)
After configuring the TCP/IP protocol, you can use the ping command to check if
your computer has successfully connected to this router. At a DOS prompt, execute
the ping command.
Ping 192.168.0.2
If the following messages (or similar) appear:
Pinging 192.168.0.2 with 32 bytes of data:
Reply from 192.168.0.2: bytes=32 time=2ms TTL=64
Reply from 192.168.0.2: bytes=32 time<1ms TTL=64
Reply from 192.168.0.2: bytes=32 time<1ms TTL=64
Reply from 192.168.0.2: bytes=32 time<1ms TTL=64
A communication link between your computer and this Router has been successfully
established. Please note that the values for bytes, time and TTL are not critical – we
are looking for a response. Otherwise, if you get the following messages:
Pinging 192.168.0.2 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
16
XH9948 – DSE WLAN 802.11g 4-Port Router
5.4 TCP/IP Configuration for Windows VISTA
Use the following steps to configure the manager PC to be a DHCP client. These
same steps must be performed for every host PC on your network if you use the
DHCP function of the Router.
1. Click the Start button and choose Settings and then Control Panel.
2. Click Classic View on the task option on the left pane
17
4. Click Manage Network Connections on the task option on the left pane
5. Right-Click on the Network Connection depicting your LAN card and click
Properties
18
XH9948 – DSE WLAN 802.11g 4-Port Router
6. From LAN properties double-click on Internet Protocol Version 4 (TCP/IPv4)
19
B. Configure IP Manually – Select Use the following IP address. The
default IP address of the Router is 192.168.0.2. So please use
192.168.0.X (where X is between 1 and 253, except 2) for the IP Address
field, 255.255.255.0 for the Subnet Mask field and 192.168.0.2 for the
Default Gateway field as shown below. Enter the DNS values which are
provided by your ISP.
After configuring the TCP/IP protocol, you can use the ping command to check if
your computer has successfully connected to this router. At a DOS prompt, execute
the ping command.
Ping 192.168.0.2
If the following messages (or similar) appear:
Pinging 192.168.0.2 with 32 bytes of data:
Reply from 192.168.0.2: bytes=32 time=2ms TTL=64
Reply from 192.168.0.2: bytes=32 time<1ms TTL=64
Reply from 192.168.0.2: bytes=32 time<1ms TTL=64
Reply from 192.168.0.2: bytes=32 time<1ms TTL=64
A communication link between your computer and this Router has been successfully
established. Please note that the values for bytes, time and TTL are not critical – we
are looking for a response. Otherwise, if you get the following messages:
Pinging 192.168.0.2 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
20
XH9948 – DSE WLAN 802.11g 4-Port Router
1. Launch your Web Browser (such as Internet Explorer 6/7 or Firefox 2.0)
2. Enter the LAN IP address http://192.168.0.2/ into the Address Bar
3. You will be prompted to enter a username and password.
Enter the default login User Name and Password as indicated below.
The default login username is admin;
the default login password is password.
Note: If the above screen does not prompt, it may means that your web-browser has
been set to a proxy. Go to Tools menu Internet Options Connections LAN
Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK
to finish it.
21
4. If the User Name and Password are correct, you should be able to configure the
router using the web browser. Please click the Quick Setup link on the left of the
main menu and the Quick Setup screen will appear. Click Next
5. The router supports three popular ways to connect to Internet. Please select one
compatible with your ISP. Click Next to enter the necessary network parameters.
22
XH9948 – DSE WLAN 802.11g 4-Port Router
If your ISP uses a "PPPoE" connection then you will to select this option, you will
see the page below. Enter the User Name and Password provided by your ISP.
These fields are case sensitive. If you have difficulty with this process, please
contact your ISP.
If your ISP uses "Dynamic IP" or you are connecting the Router into an Ethernet
port based ADSL modem then choose this option, the router will automatically
receive the IP parameters from your ISP/Modem without needing to enter any
parameters.
If your ISP requires a "Static IP", choose this option and page will appear as
shown below
o Note: The IP parameters should have been provided by your ISP or if you
are connecting it to another Ethernet based Broadband modem then you
need to use appropriate IP Address.
o IP Address - This is the WAN port’s IP.
o Subnet Mask - The Subnet Mask is used for the WAN IP address, it is
usually 255.255.255.0
23
o Default Gateway - Enter the gateway into the box if required.
o Primary DNS - Enter the DNS Server IP address into the boxes if
required. This is usually provided by your ISP
o Secondary DNS - If your ISP provides another DNS server, enter it into
this field.
6. After you complete the above, click Next, the Wireless settings page will appear
as shown below.
Note: The change of wireless settings won't take effect until the router reboots! You
can reboot it manually.
24
XH9948 – DSE WLAN 802.11g 4-Port Router
7. Click the Next button; you will then see the Finish page:
After finishing all configurations of basic network parameters, please click Finish
button to exit this Quick Setup.
25
7 Configuring the Router
Note: This manual will only cover the basic configuration of this router, the reason for
this is that the router has very comprehensive instructions for each submenu
function, these instructions can be found on the right pane when browsing the router
settings and are specific for each submenu function
7.1 Status
The Status page displays the router's current status and configuration. All
information is read-only.
1. LAN: This field displays the current settings or information for the LAN, including
the MAC address, IP address and Subnet Mask.
2. Wireless: This field displays basic information or status for wireless function,
including Wireless Radio, SSID, Channel, Mode, Wireless MAC address and IP
address.
3. WAN: These parameters apply to the WAN port of the router, including MAC
address, IP address, Subnet Mask, Default Gateway, DNS server and WAN
connection type. If PPPoE is chosen as the WAN connection type, the
Disconnect button will be shown here while you are accessing the Internet. You
can also cut the connection by clicking the button. If you have not connected to
the Internet, a Connect button will be shown instead, you can then establish
internet connection by clicking the button.
4. Traffic Statistics: This field displays the router's traffic statistics.
5. System Up Time: The time of the router running from it's powered on or reset.
26
XH9948 – DSE WLAN 802.11g 4-Port Router
7.2 Network
There are three submenus under the Network menu (shown in figure 5-2): LAN,
WAN and MAC Clone. Click any of them, and you will be able to configure the
corresponding function. The detailed explanations for each submenu are provided
below.
7.2.1 LAN
You can configure the IP parameters of LAN on this page.
• MAC Address - the physical address of the router, as seen from the LAN.
The value can't be changed.
• IP Address - Enter the IP address of your router in dotted-decimal notation
(factory default: 192.168.0.2).
• Subnet Mask - An address code that determines the size of the network.
Normally use 255.255.255.0 as the subnet mask.
Note:
1. If you change the IP Address of LAN, you must use the new IP Address to
login the router.
2. If the new LAN IP Address you set is not in the same subnet, the IP Address
pool in the DHCP server will not take effect, until they are re-configured.
3. If you had any virtual server or DMZ settings prior to changing IP Address,
these may need to be reconfigured.
7.2.2 WAN
You can configure the WAN port parameters on this page. This is the setting that
facilitates connecting the WAN port with your ISP and in turn the internet.
Note: You must 1st make sure that you have the correct settings, if you are not sure
please check with your ISP, you will need the correct settings as without this you will
not be able to connect to the internet.
27
Choose the correct connection type and configure using the settings provided by
your ISP. Once you have configured the correct settings as specified by your ISP
then Click the Save button to save your settings, you do not need to reboot the
router, as the setting goes live as soon as Save is clicked.
7.2.3 MAC Clone
You can configure the MAC address of the WAN port on this page
Some ISPs require that you register the MAC Address of your adapter, which is
connected to your cable, DSL modem or Ethernet during installation. You do not
generally need to change anything here.
• WAN MAC Address - This field displays the current MAC address of the
WAN port. If your ISP requires that you register the MAC address, please
enter the correct MAC address into this field. The format for the MAC
Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit).
• Your PC's MAC Address - This field displays the MAC address of the PC
that is managing the router. If the MAC address is required, you can click the
Clone MAC Address button and this MAC address will fill in the WAN MAC
Address field.
To restore factory MAC address, click Restore Factory MAC, Click the Save button
to save your settings.
28
XH9948 – DSE WLAN 802.11g 4-Port Router
7.3 Wireless
There are three submenus under the Wireless: Wireless Settings, MAC Filtering
and Wireless Statistics. Click any of them, and you will be able to configure the
corresponding function.
29
• Channel - This field determines which operating frequency will be used. It is
not necessary to change the wireless channel unless you notice interference
problems with another nearby access point.
• Mode - Select the desired wireless mode. The options are:
o 54Mbps (802.11g) - Both 802.11g and 802.11b wireless stations can
connect to the router.
o 11Mbps (802.11b) - Only 802.11b wireless stations can connect to the
router.
• Note: The default is "54Mbps (802.11g)", which allows both 802.11g and
802.11b wireless stations to connect to the router.
• Enable Wireless Router Radio - The wireless radio of this Router can be
enabled or disabled to allow wireless stations access. If enabled, wireless
stations will be able to access the router; otherwise, wireless stations will not
be able to access the router.
• Enable SSID Broadcast - If you select the Enable SSID Broadcast
checkbox, the Wireless Router SSID will broadcast its name (SSID) on the
air.
• Enable Wireless Security – The wireless security function can be enabled
or disabled. If disabled, the wireless stations will be able to connect the router
without encryption. It is strongly recommended that you choose this option to
encrypt your wireless network. The encryption settings are described below.
• Authentication Type - You can select one of the following types:
o WEP - Select WEP authentication type based on 802.11
authentications.
o WPA-PSK/WPA2-PSK - Select WPA/WPA2 authentication type
based on pre-shared Passphrase.
o WPA/WPA2 - Select WPA/WPA2 authentication type based on
Radius Server.
• Authentication Option - You can select one of the following options:
o Automatic - Select Shared Key or Open System authentication type
automatically based on the wireless station request.
o Shared Key - select 802.11 Shared Key authentications.
o Open System - Select 802.11 Open System authentications.
o When you select WPA-PSK/WPA2-PSK as an authentication type you
can select Automatic, WPA –PSK or WPA2-PSK as authentication
options.
o When you select WPA/WPA2 as an authentication type you can select
Automatic, WPA or WPA2 as authentication options.
• WEP Key Format - You can select ASCII or Hexadecimal format. ASCII
Code Format stands for any combination of keyboard characters in the
specified length. Hexadecimal format stands for any combination of
hexadecimal digits (0-9, a-f, A-F) in the specified length.
• WEP Key settings - Select which of the four keys will be used and enter the
matching WEP key information for your network in the selected key radio
30
XH9948 – DSE WLAN 802.11g 4-Port Router
button. These values must be identical on all wireless stations in your
network.
• Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit)
for encryption. "Disabled" means the WEP key entry is invalid.
• For 64-bit encryption - You can enter 10 hexadecimal digits (any combination
of 0-9, a-f, A-F, zero key is not permitted) or 5 ASCII characters.
• For 128-bit encryption - You can enter 26 hexadecimal digits (any
combination of 0-9, a-f, A-F, zero key is not permitted) or 13 ASCII
characters.
• For 152-bit encryption - You can enter 32 hexadecimal digits (any
combination of 0-9, a-f, A-F, zero key is not permitted) or 16 ASCII
characters.
• Encryption - When you select WPA-PSK/WPA2-PSK or WPA/WPA2 as an
Authentication Type you can select Automatic, TKIP or AES.
Note: The router will reboot automatically after you click save.
31
7.4 Forwarding (NAT)
There are four submenus under the Forwarding menu (shown in figure 5-18): Virtual
Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able
to configure the corresponding function. The detailed explanations for each submenu
are provided below.
• Service Port - The numbers of External Ports. You can type a service port or
a range of service ports (the format is XXX – YYY, XXX is Start port, YYY is
End port).
• IP Address - The IP Address of the PC running the service application
32
XH9948 – DSE WLAN 802.11g 4-Port Router
• Protocol - The protocol used for this application, either TCP, UDP, or All
• Status - The Status box lets you enable/disable the virtual server entry.
• Common Service Port – Some common services are listed in the pull-down
list.
Note: It is possible that you have a computer or server that has more than one type
of available service. If so, select another service, and enter the same IP Address for
that computer or server.
Note: If you set the virtual server of service port as 80, you must set the web
management port on Security –> Remote Management page to be any value
except 80 such as 8080. Or else there will be a conflict to disable the virtual server.
33
7.4.2 DMZ
The DMZ host feature allows one local host to be exposed to the Internet for a
special-purpose service such as Internet gaming or videoconferencing. DMZ host
forwards all the ports at the same time. Any PC whose port is being forwarded must
have its DHCP client function disabled and should have a new static IP Address
assigned to it because its IP Address may change when using the DHCP function.
You can set up DMZ host on this page as shown below
Note: After you set the DMZ host, the firewall related to the host will not work.
34
XH9948 – DSE WLAN 802.11g 4-Port Router
7.5 System Tools
There are seven submenus under the System Tools menu; Time, Firmware,
Factory Defaults, Reboot, Password, Log and Statistics. Click any of them, and
you will be able to configure the corresponding function. The detailed explanations
for the most important submenus are provided below.
New firmware versions are posted at www.dse.co.nz and can be downloaded for
free. If the router is not experiencing difficulties, there is no need to download a more
recent firmware version, unless that version has a new feature that you want to use.
Note: When you upgrade the router's firmware, you may lose its configuration
settings, so make sure you write down the router settings before you upgrade its
firmware.
Note: Do not turn off the router or press the Reset button while the firmware is being
upgraded, the router will reboot after the upgrade has been finished.
35
7.5.2 Factory Defaults
This page allows you to restore the factory default settings for the router.
Click the Restore button to reset all configuration settings to their default values.
• The default User Name: admin
• The default Password: password
• The default IP Address: 192.168.0.2
• The default Subnet Mask: 255.255.255.0
Note: Any settings you have saved will be lost when the default settings are
restored.
7.5.3 Reboot
This page allows you to reboot the router.
Click the Reboot button to reboot the router. Some settings of the router will take
effect only after rebooting, which include:
• Change LAN IP Address. (System will reboot automatically)
• MAC Clone (system will reboot automatically)
• DHCP service function.
• Static address assignment of DHCP server.
• Web Service Port of the router.
• Upgrade the firmware of the router (system will reboot automatically).
• Restore the router's settings to factory default (system will reboot
automatically).
36
XH9948 – DSE WLAN 802.11g 4-Port Router
7.5.4 Password
This page allows you to change the factory default user name and password of the
router.
It is strongly recommended that you change the factory default user name and
password of the router. All users who try to access the router's web-based utility or
Quick Setup will be prompted for the router's user name and password.
Note: The new user name and password must not exceed 14 characters in length
and must not include any spaces. Enter the new Password twice to confirm it.
37
8 Glossary
38
XH9948 – DSE WLAN 802.11g 4-Port Router
• NAT (Network Address Translation) - NAT technology translates IP
addresses of a local area network to a different IP address for the
Internet.
• PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for
connecting remote hosts to the Internet over an always-on connection by
simulating a dial-up connection.
• SSID - A Service Set Identification is a thirty-two character (maximum)
alphanumeric key identifying a wireless local area network. For the
wireless devices in a network to communicate with each other, all devices
must be configured with the same SSID. This is typically the configuration
parameter for a wireless PC card. It corresponds to the ESSID in the
wireless Access Point and to the wireless network name.
• WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a
64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE
802.11 standard.
• Wi-Fi - A trade name for the 802.11b wireless networking standard, given
by the Wireless Ethernet Compatibility Alliance (WECA, see
http://www.wi-fi.net), an industry standards group promoting
interoperability among 802.11b devices.
• WLAN (Wireless Local Area Network) - A group of computers and
associated devices communicate with each other wirelessly, which
network serving users are limited in a local area.
39
9 Appendix
9.2 My Settings
We suggest you write down your routers’ customised settings for future reference:
Name of ISP
ISP Contact
40
XH9948 – DSE WLAN 802.11g 4-Port Router
10 Support
Should you encounter problems with the installation of this device, please follow
these steps:
1. Read the Manual
2. Make sure all the cables are plugged in correctly
3. Make sure you have entered the ISP settings correctly
4. If you are using wireless, then make sure that you are using the
correct security settings and the correct key/passphrase
5. Make sure your PCs Firewall is not blocking the service you are
trying to access
6. Contact Dick Smith Electronics Computer Support.
Note: Consumers are advised not to rely on our ability to provide support for Open
Source, GNU, Freeware or Shareware software, as this software is often under
continual development. We will however help where we can which may be limited to
providing web links only. Windows software that does not fall into the categories
above is supported.
Please visit our website http://www.dse.co.nz from time to time as the most up-to-
date drivers and manuals will be posted there.
11 Warranty
This device is supplied with a 12-month, non-transferable end user warranty. In the
unlikely event that this device should fail within the warranty period, please return it,
along with your purchase receipt, to your nearest Dick Smith Electronics store.
41
Dick Smith Electronics Stores
Okara Shopping Centre, 4 Port Rd., Phone: (09) 438 0687, Fax: (09) 438 9635;
Albany: Don McKinnon Drive, Albany MegaCentre, Phone: (09) 415 7410, Fax: (09) 415
4360; Glenfield: Glenfield Road, (Above Westfield Shopping Town), Phone: (09) 442 2314, Fax: (09) 442
2317; Takapuna: 451 Lake Road, Phone: (09) 486 4037, Fax: (09) 486 4039; City: 26-28 Wyndham
Street, Phone: (09) 303 1355, Fax: (09) 303 2783; New Lynn: 3045 Great North Road, Phone: (09) 827
0433, Fax: (09) 827 0466; Henderson: Level 1 (Shop 128), Westcity Mall, Phone: (09) 838 8024, Fax: (09)
838 9258; Botany: Shop B01 Botany Town Centre, Phone: (09) 271 4100, Fax: (09) 271 4101;
Karangahape Road: 442 Karangahape Road, Phone: (09) 309 4402: Fax: (09) 373 4456; Newmarket: 50
Remuera Road, Phone: (09) 524 7033, Fax: (09) 524 7033; St Lukes: Cnr St Lukes Road and Wagener
Road, Phone: (09) 845 0102, Fax: (09) 845 0105; Onehunga: 252-258 Onehunga Mall, Phone: (09) 634
6767; Pakuranga: Westfield Shoppingtown, Reeves Road, Phone: (09) 576 6604, Fax: (09) 576 4446;
Manukau City: Cnr Ronwood Avenue & Great South Road, Phone: (09) 262 4150, Fax: (09) 262 4151;
Papakura: 130 Great South Road, Phone: (09) 298 0943, Fax: (09) 296 1713; Pukekohe: 106 Manukau
Road, Phone: (09) 237 1530, Fax: (09) 237 1534. 509 Pollen St, Phone: (07) 867 9215, Fax:
(07) 867 9266; Dick Smith Electronics PowerHouse: 4 Thackeray Street, Phone: (07)
834 4099 Fax: (07) 834 4098; Barton Street: 299 Barton Street, Phone: (07) 839 4491, Fax: (07) 838
1226. Cnr Willow & Springs Street, Phone: (07) 578 7071, Fax: (07) 577 6674.
1175 Pukuatua Street, Phone: (07) 349 0270, Fax: (07) 348 2464.
Shop 6, 2 Owens Place, Phone: (07) 574 3942, Fax: (07) 574 3943. 233 Emerson St, Phone:
(06) 835 5137, Fax: (06) 834 0463; ! 70-72 Devon Street East, Phone: (06) 758 3309,
Fax: (06) 758 5034; 122b Victoria Ave, Phone: (06) 348 7270, Fax: (06) 348 7275.
Cnr Fitzherbert Ave & Ferguson St, Phone: (06) 359 4447, Fax: (06) 359
4452. Featherston Street: 171 Featherston Street, Phone: (04) 473 9858, Fax: (04)
473 0407; Vivian Street: 57 Vivian Street, Phone: (04) 384 8198, Fax: (04) 801 6258; Manners Mall: 4
Manners Mall, Phone: (04) 385 6788, Fax: (04) 385 6785; Lower Hutt: 90 Queens Drive, Phone: (04) 566
2022, Fax: (04) 566 1277; Upper Hutt: 133 Main St, Phone: (04) 528 0505, Fax: (04) 527 0523;
Johnsonville: Shop 1, 120 Johnsonville Rd Phone: (04) 461 7590 Fax: (04) 461 7592. Porirua: Porirua
Mega Centre, 36 Parumoana Street, Phone: (04) 237 6654, Fax: (04) 237 6456. 150 Hardy
Street, Phone: (03) 548 9161, Fax: (03) 548 2900. " 5 Maxwell Road Phone: (03) 578 1132
Fax: (03) 577 8981. Manchester Street: 130 Manchester Street, Phone: (03) 365
5560, Fax: (03) 365 5561; The Palms: Cnr Marshlands & New Brighton Roads, Shirley, Phone: (03) 386
2670, Fax: (03) 386 2147; Colombo Street: Cnr Colombo & St Asaph Streets, Phone: (03) 366 2703, Fax:
(03) 379 4684; Papanui: Cnr Main North Rd & Langdon's Road, Phone: (03) 352 8770, Fax: (03) 352
7608; Riccarton: 107 Riccarton Road, Phone: (03) 343 0812, Fax: (03) 343 3880. 295 Stafford
Street, Phone: (03) 684 6876, Fax: (03) 684 7678. Moray Place: 342 Moray Place, Phone:
(03) 474 1096, Phone: (03) 477 4495, Fax: (03) 474 1032; Cumberland Street: 59 Cumberland Street,
Phone: (03) 470 1680, Phone: (03) 470 1681, Fax: (03) 470 1682. 63 Leven Street,
Phone: (03) 214 4363, Fax: (03) 214 0672
Authorised Distributors
< Kerikeri Electronics Ltd, 63 Main Street, Kerikeri, Phone: (09) 407 5589, Fax: (09) 407 5587.
Tronix, Westpac Plaza, Bakehouse Lane, Orewa, Phone: (09) 426 2007, Fax: (09) 427 8085.
Electronics Plus, 80 Arawa Steet, Matamata, Phone: (07) 888 5955, Fax: (07) 888 5944.
Piaggi Systems & Software Ltd, 509 Pollen Street, Thames, Phone: (07) 868 9691, Fax: (07)
868 7980. Boonen Electronics, 76 The Strand, Whakatane, Phone: (07) 308 8761, Fax:
(07) 308 9151. Electronic Plus, 63 Jellicoe Street, Te Puke, Phone: (07) 573 7544, Fax: (07)
573 9490. Talktime 2000 Limited, Cnr Gascoigne & Tamamutu Steets, Taupo, Phone: (07) 377
0668, Fax (07) 377 0669. " AMPS Electronics, 131 Gladstone Road, Gisborne, Phone: (06)
868 1366, Fax (06) 867 9103. Baytech Services Limited, 114 North King Street, Hastings,
Phone: (06) 878 8962, Fax: (06) 878 5509. Hedley's Home & Office, 152 Queen Street,
Masterton, Phone: (06) 370 9202, Fax: (06) 370 9303. Kapiti Electronics Ltd, 7-8 Kapiti Lights,
Amohia Street, Paraparaumu, Wellington, Phone: (04) 904 4100, Fax: (04) 904 4101 # David
Brice Electronics Ltd, 47 Kimbolton Road, Fielding, Phone: (06) 323 7141, Fax: (06) 323 7921;
R R T Ltd., The Gables, 96-98 High St., Rangiora, Phone: (03) 310 7383, Fax: (03) 310
7384; $ Central Betta Electrical, 15 Tarbert Street, Alexandra, Phone: (03) 448 7317, Fax:
(03) 448 7631.
42