0 evaluări0% au considerat acest document util (0 voturi)
958 vizualizări0 pagini
This document provides technical information on standard cable trunkings and cable management systems. It outlines specifications for both metallic and uPVC cable trunkings. For metallic trunkings, it specifies requirements such as compliant standards, materials used, minimum wall thicknesses, support brackets, and provision of circuit protection conductors. For uPVC trunkings, it outlines compliance with British standards on classification, resistance to ingress, dimensions, impact testing, resistance to heat and burning, and marking requirements. The document is intended to ensure cable trunkings meet appropriate technical specifications.
This document provides technical information on standard cable trunkings and cable management systems. It outlines specifications for both metallic and uPVC cable trunkings. For metallic trunkings, it specifies requirements such as compliant standards, materials used, minimum wall thicknesses, support brackets, and provision of circuit protection conductors. For uPVC trunkings, it outlines compliance with British standards on classification, resistance to ingress, dimensions, impact testing, resistance to heat and burning, and marking requirements. The document is intended to ensure cable trunkings meet appropriate technical specifications.
Drepturi de autor:
Attribution Non-Commercial (BY-NC)
Formate disponibile
Descărcați ca PDF, TXT sau citiți online pe Scribd
This document provides technical information on standard cable trunkings and cable management systems. It outlines specifications for both metallic and uPVC cable trunkings. For metallic trunkings, it specifies requirements such as compliant standards, materials used, minimum wall thicknesses, support brackets, and provision of circuit protection conductors. For uPVC trunkings, it outlines compliance with British standards on classification, resistance to ingress, dimensions, impact testing, resistance to heat and burning, and marking requirements. The document is intended to ensure cable trunkings meet appropriate technical specifications.
Drepturi de autor:
Attribution Non-Commercial (BY-NC)
Formate disponibile
Descărcați ca PDF, TXT sau citiți online pe Scribd
CAWANGAN ELEKTRIK TECHNICAL INFORMATION ON STANDARD CABLE TRUNKINGS I CABLE MANAGEMENT SYSTEM A. COMPANY 1. Name of Company 2. Address 3. Telephone No ............................................................... 4. Faxs No . .............................................................. 5 . S.T Registration No . ................................................................ 6. Validity Date of Registration : ............................................................... 7. SIRIM Test Report ............................................. -(If related) 8. SIRIM Test Certificate No : .............................................. (If related) 9. Other Accredicted Test Report/Certificate: .................................................... B. PRODUCT SPECIFICATION I. Brand's Name ................................................................ 2. Model No ............................................................. 3. Approval Standard . ................................................................ 4. Country Of Origin ................................................................ 4. I Full Type Test ReporVcertificate No.from: i) SIRIM : ........................................ ii) Others : ........................................ Catatan Pejabat Kandas Catatan Pe'abat k3 1 0 - Kandas 1 5.0 CABLE TRUNKING (METALLIC) 5.1 Comply with IEC 61084 q yes q NO 0 5.2 Fabricated from galvanished sheet steel and finished with 2 coats of standard orange enamel q yes NO 0 5.3 Equipped with removable covers at suitable intervals q Yes No 0 6.0 Shall have the following minimun wall thickness Nomiilal Size(m11 x mrn) Minimun Wall Thickness(mm) i) 50 x50 and below 1.0 yes q NO 0 ii) 75 x 50 to 100x100 1.2 Yes q No 0 iii) 150 x 50 to 300 x150 1.6 q yes q NO 0 iv) Above 300 x 150 2.0 O ~ e s ONO 0 If others from the above please specify.. . . . . . . . . . . . . . . . . . .. . . . .. 6.5 All truilking elbows,offsett & combinatioll elbow ,adaptors & tee shall have the same thickness as the straight trunking q yes NO 0 6.6 Shall be maufactured by the same manufacturer Yes No 0 6.7 Shall be supported by fixing brackets i.e not be in contact with wall or floor slabs yes NO 0 6.8 The brackets shall be installed at interval not greater 1500mm for Vertical Run yes NO 0 6.9 The brackets shall be installed at interval not greater lOOOmm For horizontal nin yes NO 0 7.0 The brackets shall be denlsted ,finished in a primer & coated with standard orange enamel yes q NO 0 8.0 Whenever tnlilking passess through a floor or a fire resistance wall , fire resistance barrier shall be provided Yes No 0 Informative to be used together during installation: 8. 1 When conduit is tapped from the trunking ,suitable brass type smoother bushes shall be fitted at all conduit termination . q Yes q No 0 ... Information CPC For Site Installation: 9.0 A1 1 trunkings shall have either tinned copper tape of dimension not less than 25mm x 3 mrn as circuit protector conductor or earth cable of approriate D y e s DNOO 10.0 Others (please specify) 11.0 Under Floor Trunking (i.e Raised Floor, Flushed Floor.. .etc) i ) Please give details of the test report : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii) The Dimensions - Please used Lampiran : ............... .............. 11 .I Comply to BS . . . . . . . . . . . . ., IEC , EN Please specify 12.0 Cable trunking-uPVC(Cab1e trunking made of insulating material) 12.1 Comply to BS 4678:Part 4:1982 : OYe s ~ N O O Others standard,please specify.. ............. Have an approval letter from Jabatan Bomba: q Yes q No 0 12.2 Comply to Clause 4 : Classification e.g : Trunking for heavy mechanical stresses : OYe s ONOO : Comply according to resistance against ingress of solid object:n Yes q No 0 . . . . . . . ........ 12.3 Dimension -Width.. . . . . x Height.. Thickness.. .(mm) .................................................................................... Please specify !If needed arise please used additional paper- 12.4 Clause 9.3- (i) Impact Test Data - Heavy Duty (3.3 kg mass of hammer & impact Energy 10 J )- 12.5 Clause 10-Resistance to heat- Ball pressure test. q Yes q No 0 12.6 Clause 1 1-Resistance to burning.. ......... n ~ e s UNOO 12.7 Marking - code of marking e.g 425 plus additional marking code-/. ..... Please specify . 13.0 Others for uPVC trunking -(If there is a deviation from 12.0 & Please explain)- ...................................................................................... (Note : The above clauses to be tested is just an example of the important clauses that malufacturers should be done but manufacturers also can do full type test .)