Sunteți pe pagina 1din 2

Remove CP Remove the code protection in some cases, it depends if the code protection was installed in the program

or while programming. Erase PIC Deletes the program or code in the connected PIC. Blank check Check if the PICs memory is empty Write HEX-File into PIC Writes the program previously loaded with the Select HEX-File as source option, into the connected PIC. Compare PIC with HEX-File Compares the content of the memory with the previously loaded program. Before using your new USB port PIC programmer please read this instruction manual to prevent any damage. Put it away in a safe place for future references. WARNING To avoid damaging your programmer, please ensure pins are connected to the correct side. Do not place the PIC-600 over metallic surfaces. Do not place metallic objects over the programmer Read from PIC into new HEX-File Reads the Pics memory and save into a new .HEX le, you must enter a name and location for the le. Target: Run Use this option to switch the PIC to run mode after programming it into the ICSP port. Be careful to insulate the ICSP port from the rest of the circuit where the PIC is installed.

SPECIFICATIONS DRIVER INSTALLATION IN WINDOWS XP 5V (through USB port) 1.- Place the installation CD into the CD-ROM drive. 2.- AS part of the content of the disc, you will nd the folder PIC-600, it Product design and specications are subject to change without contains driver and software folders. previous notice. 3.- Copy the folder PIC-600 and its content into the hard disk. Do not forget the location, you will use it later. 4.- Use a USB cable type B (USB-450) to connect the programmer to computer. 5.- The computer will detect the new hardware, the Found New Hardware Wizard runs. 6.- Select No, not this time and click Next to continue. 7.- Now select Search for the best driver in these locations, click Next to Product: USB port PIC programmer continue. Part number: PIC-600 Brand: Steren 8.- Click on Browse to nd the folder Driver. Then click Next to continue. 9.- The installation process begins. If a warning message pop up, please click OK to continue. WARRANTY This Steren product is warranted under normal usage against defects in workmanship and materials to the 10.- The completed installation window will appear shortly afterwards, original purchaser for one year from the date of purchase. just click on Finish. Do not place any PIC on the base while installing drivers, may cause damages on it. The software have not drivers for Windows Vista. In Windows Vista, the softawre will run changing the compatibility mode to Windows Xp SP2. OPERATION IMPORTANT Before to run the software, it is recommendable to connect the PIC rst, and then open the software, otherwise the software may not recognize the programmer. Connect the PIC-600 to an available USB port, open the Software folder and click twice over PIC-600 USB-Burn.exe le (if you want, create a Quick Launch into the desktop) When the software recognize the programmer, next options will display in the Basics tab: Identify PIC in programmer This option identify the placed PIC on the base or connected to ICSP port. First, make sure to select the pins in the IC-Socket / ICSP box dialog, and the family in PIC Family box dialog. Select HEX-File as source Open the le to be loaded into the PIC, it must have the .HEX format.
CONDITIONS 1.- This warranty card with all the required information, invoice or purchase ticket, product box or package, and product, must be presented when warranty service is required. 2.- If the product stills on the warranty time, the company will repair it free of charge. 3.- The repairing time will not exceed 30 natural days, from the day the claim was received. 4.- Steren sell parts, components, consumables and accesories to costumer, as well as warranty service, at any of the addresses mentioned later. THIS WARRANTY IS VOID IN THE NEXT CASES: If the product has been damaged by an accident, acts of God, mishandling, leaky batteries, failure to follow enclosed instructions, improper repair by unauthorized personnel, improper safe keeping, among others. a) The consumer can also claim the warranty service in the purchase establishment. b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase ticket. RETAILER INFORMATION Name of the retailer Address Product Brand Part number Serial number Date of delivery

In case your product fails or have questions, please contact your nearest dealer. If you are in Mexico, please give a call to our Call Center. Call Center 01 800 500 9000

Select HEX-File as source Abre el archivo que ser cargado al PIC, debe tener extensin .HEX Remove CP Quita la proteccin de cdigo en algunos casos, depende si la proteccin del cdigo fue colocada en el programa o durante la programacin. Erase PIC Borra el programa o cdigo del PIC insertado o conectado. Blank check Revisa que la memoria del PIC est vaca. Antes de utilizar su nuevo Mdulo programador de PICs lea este instructivo para evitar cualquier mal funcionamiento. Gurdelo para futuras referencias. ADVERTENCIA Para evitar cualquier dao al programador, asegrese de que los pines de los PICs a programar estn correctamente conectados. No coloque la tarjeta programadora sobre supercies metlicas. No coloque objetos metlicos sobre la tarjeta. Write HEX-File into PIC Escribe el programa previamente abierto con la opcin Select HEXFile as source en la memoria del PIC insertado o conectado. Compare PIC with HEX-File Compara el contenido de la memoria del PIC con el programa que previamente se carg. Read from PIC into new HEX-File Lee la memoria del PIC y lo guarda en un archivo .HEX nuevo, para lo cual se debe escribir el nombre y la ubicacin del nuevo archivo .HEX. Target: Run sta es una opcin para poner el PIC en modo de ejecutar cuando se ha programado a travs del puerto ICSP, se debe tener mucho cuidado de aislar muy bien el puerto ICSP del resto del circuito donde el PIC est instalado. ESPECIFICACIONES (a travs del puerto USB)

INSTALACIN DE DRIVERS EN WINDOWS XP 1.- Inserte el disco de instalacin en la unidad de CD-ROM de la computadora. 2.- Abra el contenido del CD, podr observar una carpeta llamada PIC-600, la cual contiene las carpetas driver y software. 3.- Copie la carpeta PIC-600 a su disco duro, en la ubicacin que preera. No olvide donde la copi, posteriormente se requerir. 4.- Mediante un cable con conector USB tipo B (USB-450) conecte el programador PIC a un puerto USB disponible de la computadora. 5.- La computadora detectar el nuevo equipo y el Asistente para hardware nuevo encontrado se ejecutar. 6.- Seleccione la opcin No por el momento, y presione Next para continuar. 7.- En la siguiente ventana seleccione la opcin Instalar desde una lista o ubicacin especca (avanzando), presione Next para continuar. 8.- Seleccione la opcin Examinar para localizar la carpeta Driver que previamente copi. Presione Next para continuar. 9.- El proceso de instalacin comenzar. Es posible que durante el proceso, aparezca un mensaje de advertencia acerca del logotipo de Windows XP, presione Continuar. 10.- Presione Finalizar para concluir con el proceso. Ahora podr comenzar a utilizar el programador. Asegrese de que no existe ningn PIC conectado al programador durante la instalacin de drivers, se podra daar el programador. El disco de instalacin NO contiene drivers para Windows Vista. En Windows Vista el software se ejecuta cambiando al modo de compatibilidad (Windows XP SP2) OPERACIN DEL PROGRAMADOR IMPORTANTE Despus de instalado su programador PIC-600 es recomendable que primero lo conecte antes de abrir el programa PIC-600 US-Burn.exe, en caso de no hacerlo el software de programacin puede no detectar el programador. Conecte el equipo a un puerto USB disponible de la computadora, abra la carpeta Software, dentro de la carpeta PIC-600, y haga doble clic en el archivo PIC-600 US-Burn.exe. (Si lo requiere puede crear un acceso directo en su escritorio para facilitar el acceso). Una vez ejecutado el programa y reconocido el programador le deben aparecer las siguientes opciones dentro de la pestaa Basics: Identify PIC in programmer Identica el PIC insertado en la base ZIF o conectado al puerto ICSP, primero asegrese de haber seleccionado los pines del PIC en el cuadro IC-Socket / ICSP y la familia en el cuadro PIC Family.

5V

Las caractersticas del equipo pueden ser modicadas sin previo aviso.
Producto: Mdulo programador de PICs USB Modelo: PIC-600 Marca: Steren
PLIZA DE GARANTA Esta pliza garantiza el producto por el trmino de un ao en todas sus partes y mano de obra, contra cualquier defecto de fabricacin y funcionamiento, a partir de la fecha de entrega. CONDICIONES 1.- Para hacer efectiva la garanta, presente sta pliza y el producto, en donde fue adquirido o en Electrnica Steren S.A. de C.V. 2.- Electrnica Steren S.A de C.V. se compromete a reparar el producto en caso de estar defectuoso sin ningn cargo al consumidor. Los gastos de transportacin sern cubiertos por el proveedor. 3.- El tiempo de reparacin en ningn caso ser mayor a 30 das, contados a partir de la recepcin del producto en cualquiera de los sitios donde pueda hacerse efectiva la garanta. 4.- El lugar donde puede adquirir partes, componentes, consumibles y accesorios, as como hacer vlida esta garanta es en cualquiera de las direcciones mencionadas posteriormente. ESTA PLIZA NO SE HARA EFECTIVA EN LOS SIGUIENTES CASOS: 1.- Cuando el producto ha sido utilizado en condiciones distintas a las normales. 2.- Cuando el producto no ha sido operado de acuerdo con el instructivo de uso. 3.- Cuando el producto ha sido alterado o reparado por personal no autorizado por Electrnica Steren S.A. de C.V. El consumidor podr solicitar que se haga efectiva la garanta ante la propia casa comercial donde adquiri el producto. Si la presente garanta se extraviara, el consumidor puede recurrir a su proveedor para que le expida otra pliza de garanta, previa presentacin de la nota de compra o factura respectiva. DATOS DEL DISTRIBUIDOR Nombre del Distirbuidor Domicilio Producto Marca Modelo Nmero de serie Fecha de entrega En caso de que su producto presente alguna falla, acuda al centro de distribucin ms cercano a su domicilio y en caso de tener alguna duda o pregunta por favor llame a nuestro Centro de Atencin a Clientes, en donde con gusto le atenderemos en todo lo relacionado con su producto Steren. Centro de Atencin a Clientes 01 800 500 9000

ELECTRONICA STEREN S.A. DE C.V. Camarones 112, Obrero Popular, 02840, Mxico, D.F. RFC: EST850628-K51 STEREN PRODUCTO EMPACADO S.A. DE C.V. Bilogo MaximIno Martnez No. 3408 Int. 3 y 4, San Salvador Xochimanca, Mxico, D.F. 02870, RFC: SPE941215H43 ELECTRONICA STEREN DEL CENTRO, S.A. DE C.V. Rep. del Salvador 20 A y B, Centro, 06000, Mxico. D.F. RFC: ESC9610259N4 ELECTRONICA STEREN DE GUADALAJARA, S.A. Lpez Cotilla No. 51, Centro, 44100, Guadalajara, Jal. RFC: ESG810511HT6 ELECTRONICA STEREN DE MONTERREY, S.A. Coln 130 Pte., Centro, 64000, Monterrey, N.L. RFC: ESM830202MF8 ELECTRONICA STEREN DE TIJUANA, S.A. de C.V. Calle 2a, Jurez 7636, Centro, 22000, Tijuana, B.C.N. RFC: EST980909NU5

S-ar putea să vă placă și