Documente Academic
Documente Profesional
Documente Cultură
CODE: 00ZARM455UA1E
MODEL
AR-M351U/M451U AR-M355U/M455U
CONTENTS
[1] GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 [2] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 [3] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 [4] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 [5] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . . . . . . . 5-1 [6] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 6-1 [7] MAINTENANCE AND DETAILS OF EACH SECTION . . . . . . . . . . 7-1 [8] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 [9] SIMULATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 [10] MACHINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 [11] TROUBLE CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 [12] ROM VERSION-UP METHOD . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1 [13] ELECTRICAL SECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
Parts marked with are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used for after sales service only. The contents are subject to change without notice.
CAUTION
Cautions on laser
Wave length Pulse times 785 nm +10 nm 15 nm At the production line, the output power of the scanner unit is adjusted to 0.4 MILLIWATT PLUS 8 % and is maintained constant by the operation of the Automatic Power Control (APC). Caution This product contains a low power laser device. To ensure safety do not remove any cover or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.
North America: 35 cpm model: (6.2 s 6.2 ns)/7 mm 45 cpm model: (4.8 s 4.8 ns)/7 mm Europe: 35 cpm model: (6.2 s 6.2 ns)/7 mm 45 cpm model: (4.8 s 4.8 ns)/7 mm 0.2 mW - 0.4 mW
Output power
For Europe:
CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT
Do not remove the cabinet, operation panel or any other covers. The equipment's exterior covers contain several safety interlock switches. Do not bypass any safety interlock by inserting wedges or other items into switch slots.
Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
CAUTION INVISIBLE LASER RADIATION WHEN OPEN INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM. VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEFFNET UND SICHERHEITSVERRIEGELUNG BERBRCKT. NICHT DEM STRAHL AUSSETZEN. ADVARSEL USYNLIG LASERSTRLNING VED BNING, NR SIKKERHEDSBRYDERE ER UDE AF FUNKTION. UNDG UDSAETTELSE FOR STRLNING. VAROITUS! LAITTEEN KYTTMINEN MUULLA KUIN TSS KYTTOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KYTTJN TURVALLISUUSLUOKAN 1 YLITTVLLE NKYMTTMLLE LASERSTEILYLLE.
Laserstrahl
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM. UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEFFNET UND SICHERHEITSVERRIEGELUNG BERERCKT. NICHT DEM STRAHL AUSSETZEN. USYNLIG LASERSTRLING VED BNING, NR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDG UDSAETTELSE FOR STRLNING. USYNLIG LASERSTRLING NR DEKSEL PNES OG SIKKERHEDSLS BRYTES. UNNG EKSPONERING FOR STRLEN.
OSYNLIG LASERSTRLNING NR DENNA DEL R PPNAD OCH SPRRAR R URKOPPLADE. STRLEN R FARLIG. BETRAKTA EJ STRLEN.
LASER KLASSE 1
VARNING OM APPARATEN ANVNDS P ANNAT STT N I DENNA BRUKSANVISNING SPECIFICERATS, KAN ANVNDAREN UTSTTAS FR OSYNLIG LASERSTRLNING, SOM VERSKRIDER GRNSEN FR LASERKLASS 1.
manuals4you.com
CONTENTS
[1] GENERAL 1. Note for servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 A. Cautions for servicing . . . . . . . . . . . . . . . . . . . . . .1-1 [2] CONFIGURATION 1. System configuration . . . . . . . . . . . . . . . . . . . . . . . . .2-1 A. Basic system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1 B. Option lineup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2 C. List of combination of peripheral devices . . . . . . .2-4 [3] SPECIFICATIONS 1. Basic Specification . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1 A. Base Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1 B. Document Feeding Equipment . . . . . . . . . . . . . . .3-2 C. Output Equipment . . . . . . . . . . . . . . . . . . . . . . . . .3-2 2. Specific Function . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2 A. Printer Function . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2 B. Image send function . . . . . . . . . . . . . . . . . . . . . . .3-5 C. Copy function . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7 3. 4. [4] B/W Scanner Module (DSPF). . . . . . . . . . . . . . . . . . .3-8 Rack for Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9 [6] UNPACKING AND INSTALLATION 1. CONSUMABLE PARTS 1. Supply system table . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 A. European Subsidiary/East Europe/Russia/ Australia/New Zealand . . . . . . . . . . . . . . . . . . . . .4-1 B. Taiwan (Aurora). . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 C. Asia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 D. Middle East/Africa/Israel/Philippines . . . . . . . . . . .4-1 E. Hong Kong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 F. China . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 2. Maintenance parts list. . . . . . . . . . . . . . . . . . . . . . . . .4-2 A. Europe/Australia/New Zealand/Taiwan . . . . . . . . .4-2 B. Agency/Asia/Middle East/Africa/ Latin America . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2 C. Hong Kong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3 D. China . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3 2. Production number identification . . . . . . . . . . . . . . . .4-4 A. Drum cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4 B. Toner cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4 C. Developer cartridge . . . . . . . . . . . . . . . . . . . . . . . .4-4 3. Environmental conditions . . . . . . . . . . . . . . . . . . . . . .4-4 A. Operating conditions . . . . . . . . . . . . . . . . . . . . . . .4-4 B. Storage conditions. . . . . . . . . . . . . . . . . . . . . . . . .4-4 9. 8. 7. 6. 5. 4. 2. 3. Installing procedure flowchart . . . . . . . . . . . . . . . . . . 6-1 Note for installation place . . . . . . . . . . . . . . . . . . . . . 6-2 Unpacking procedure . . . . . . . . . . . . . . . . . . . . . . . . 6-2 A. AR-M355U/M455U (North America), AR-M351U/M451U (Europe) . . . . . . . . . . . . . . . . 6-2 B. AR-M351U/M451U (Except for Europe) . . . . . . . 6-2 Remove the locking tape (AR-M355U/M455U (North America), AR-M351U/M451U (Europe)) . . . . . . . . . . . . . . . . . . 6-3 Unpacking and installation of the desk unit . . . . . . . . 6-3 A. AR-D28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 B. AR-D27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 C. AR-MU2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Unpacking and installation of the rack (AR-RK2) (Except for North America/Europe) . . . . . . . . . . . . . . 6-9 Unpacking and installation of the AR-EF3 (Except for North America/Europe) . . . . . . . . . . . . . 6-10 Machine installing procedure. . . . . . . . . . . . . . . . . . 6-11 A. Setting related to process . . . . . . . . . . . . . . . . . 6-11 B. Toner cartridge settings . . . . . . . . . . . . . . . . . . . 6-11 C. Setting related to fusing . . . . . . . . . . . . . . . . . . . 6-12 D. Paper setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12 Automatic developer adjustment . . . . . . . . . . . . . . . 6-12 8. 7. 6. 5. [5] EXTERNAL VIEWS AND INTERNAL STRUCTURES 1. 2. 3. 4. Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Operation panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Job status screen (common to print, copy, fax, network scan and Internet fax) . . . . . . . . . . . . . . . . . 5-4 Cross sectional view . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 B. Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Switch, Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 B. Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 B. Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Motor, Clutch, Solenoid . . . . . . . . . . . . . . . . . . . . . . . 5-8 A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 B. Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
10. Print test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13 11. Distortion adjustment (Except for North America/Europe) . . . . . . . . . . . . . 6-13 12. Attach the document scanning label . . . . . . . . . . . . 6-13 13. Key sheet attachment . . . . . . . . . . . . . . . . . . . . . . . 6-13 14. Adjuster installation and adjustment . . . . . . . . . . . . 6-14 15. Using the transport handle . . . . . . . . . . . . . . . . . . . 6-14
[7]
MAINTENANCE AND DETAILS OF EACH SECTION [Maintenance System Table] . . . . . . . . . . . . . . . . . . . . . . .7-1 1. 2. 3. Engine section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1 Scanner / DSPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2 Peripheral devices . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
[9]
SIMULATION 1. 2. Outline and purpose . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Code-type simulation. . . . . . . . . . . . . . . . . . . . . . . . . 9-1 A. Operating procedures and operations . . . . . . . . . 9-1 B. Simulation list . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 C. Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 3. Other related items . . . . . . . . . . . . . . . . . . . . . . . . . 9-87
[DETAILS OF EACH SECTION] . . . . . . . . . . . . . . . . . . . .7-4 1. Process section . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-4 [OPC drum section] . . . . . . . . . . . . . . . . . . . . . . . . . .7-6 [Transfer section] . . . . . . . . . . . . . . . . . . . . . . . . . . .7-11 [Developing section] . . . . . . . . . . . . . . . . . . . . . . . . .7-16 2. 3. 4. 5. 6. 7. 8. 9. Fusing section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-21 Paper feed section . . . . . . . . . . . . . . . . . . . . . . . . . .7-26 Transport section/Paper exit reverse section . . . . . .7-33 Laser scanner section. . . . . . . . . . . . . . . . . . . . . . . .7-43 Scanner section . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-46 DSPF section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-54 Operation panel section . . . . . . . . . . . . . . . . . . . . . .7-62 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-66 5. 4. 2. 3.
[10] MACHINE OPERATION 1. Acceptable originals . . . . . . . . . . . . . . . . . . . . . . . . 10-1 A. Size and weight of acceptable originals . . . . . . . 10-1 B. Total number of originals that can be set in the document feeder tray . . . . . . . . . . . . . . . . 10-1 Standard original placement orientations . . . . . . . . 10-1 Automatic copy image rotation rotation copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 Specifications of paper trays . . . . . . . . . . . . . . . . . . 10-2 A. Applicable plain paper . . . . . . . . . . . . . . . . . . . . 10-2 B. Applicable special paper . . . . . . . . . . . . . . . . . . 10-3 Printing onto envelopes . . . . . . . . . . . . . . . . . . . . . . 10-3 A. Fusing unit pressure adjusting levers . . . . . . . . 10-3 [11] TROUBLE CODES 1. 2. 3. 4. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 Trouble codes list . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 Details of trouble codes . . . . . . . . . . . . . . . . . . . . . . 11-3 Other related items . . . . . . . . . . . . . . . . . . . . . . . . 11-14
10. Drive section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-67 11. Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-69 12. PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-72 13. Fan motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-74 [8] ADJUSTMENTS 1. Process section . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1 A. Doctor gap adjustment . . . . . . . . . . . . . . . . . . . . .8-1 B. MG roller main pole position adjustment . . . . . . . .8-1 C. High voltage output adjustment. . . . . . . . . . . . . . .8-2 2. Image check, adjustment . . . . . . . . . . . . . . . . . . . . . .8-3 A. Adjustments on the engine side . . . . . . . . . . . . . .8-3 B. Adjustment on the scanner side . . . . . . . . . . . . . .8-6 3. Scanner section . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-10 A. OC scan distortion adjustment (MB-B rail height adjustment) . . . . . . . . . . . . . . .8-10 B. Vertical image distortion balance adjustment (Copy lamp unit installing position adjustment) . . . . . . . . . . . . . . . . . . . . . .8-11 C. Vertical image distortion balance adjustment (No. 2/3 mirror base unit installing and position adjustment) . . . . . . . . . . . . . . . . . . . . . .8-11 D. Vertical (sub scanning direction) distortion adjustment [Winding pulley position adjustment] . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-11 E. Height adjustment of original detection light emitting unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-12 F. Original size detection photo sensor check . . . . .8-12 G. Original size detection photo sensor adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-12 H. Image density adjustment . . . . . . . . . . . . . . . . . .8-13 I. DSPF width detection adjustment . . . . . . . . . . . .8-17
[12] ROM VERSION-UP METHOD 1. 2. 3. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1 Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1 Flash ROM update procedures . . . . . . . . . . . . . . . . 12-1 A. Preliminary arrangement . . . . . . . . . . . . . . . . . . 12-1 B. Update procedure 1 (Writing with each ROM inserted to the specified slot) . . . . . . . . . . . . . . . 12-2 C. Update procedures 2 (Writing to each ROM by use of CN6 of the controller PWB) . . . . . . . . 12-2 D. In case of Result: NG . . . . . . . . . . . . . . . . . . . 12-3 E. Turning off the power during update . . . . . . . . . 12-3 F. Update window display in normal booting . . . . . 12-3 G. Update process flow . . . . . . . . . . . . . . . . . . . . . 12-3 [13] ELECTRICAL SECTION 1. 2. 3. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1 Actual wiring chart . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2 Signal name list . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-19
manuals4you.com
[1] GENERAL
1. Note for servicing
Pictogram This Service Manual uses some pictographs to assure safe operation. Please understand the meanings of pictographs before servicing. CAUTION: If this CAUTION is ignored, an injury or damage to property could occur.
Fusing unit
3) Do not look directly at the light source of the scanner module. Doing so may damage your eyes. 4) Five adjusters are provided on all optional stand/paper drawer units. These adjusters should be lowered until they contact the floor.
Adjuster
manuals4you.com
Lock
Release
5) Do not make any modifications to this machine. Doing so may result in personal injury or damage to the machine. 6) Since this machine is heavy, it is recommended that it be moved by more than one person to prevent injury. 7) When connecting this machine to a computer, be sure to first turn both the computer and the machine off. 8) Do not print anything which is prohibited from printing by law. The following items are normally prohibited from printing by national law. Other items may be prohibited by local law. Money Stamps Bonds Stocks Bank drafts Checks Passports Driver's licenses 9) Do not throw toner or a toner cartridge into fire. Toner may be spattered, causing a burn. 10) Store toner or toner cartridges in a hard-to-reach place for children.
[2] CONFIGURATION
1. System configuration
A. Basic system
AR-M351U/M451U (Copier/Printer model) AR-M355U/M455U (Copier model)
Necessary options Any one of the stand/MPD & 2000 sheet paper drawer (AR-D28), the stand/3 x 500 sheet paper drawer (AR-D27), or the multi purpose drawer (AR-MU2)* Any one of the upper exit tray extension (AR-TE4), the finisher (AR-FN6), the mail-bin stacker (AR-MS1), or the right upper exit tray (AR-TE5) AR-EF3 AR-RK2 * To install the AR-MU2, the exclusive-use desk is required.
manuals4you.com
B. Option lineup
For combinations of options, refer to "C. List of combination of peripheral devices" described later.
4. Multi purpose drawer (AR-MU2) 3. Stand/3 x 500 sheet paper drawer (AR-D27) 2. Stand/MPD & 2000 sheet paper drawer (AR-D28)
No. 1 2 3 4 5 6 7 8 9
Option item Scanner module with DSPF Stand/MPD & 2000 sheet paper drawer Stand/3 x 500 sheet paper drawer Multi purpose drawer Upper exit tray Right upper exit tray Exit tray Duplex module/bypass tray Duplex module AR-EF3 AR-D28 AR-D27 AR-MU2 AR-TE4 AR-TE5 AR-TE3 AR-DU4 AR-DU3
Installing conditions Simultaneous installation with the large capacity paper feed desk (AR-D28) or the 3-stage paper feed desk (AR-D27) is inhibited. Required when the finisher (AR-FN6) or the mail-bin stacker (AR-MS1) is not installed. Required when the duplex module (AR-DU3) is installed and the saddle stitch finisher (AR-FN7) is not installed. Any one of the multi purpose drawer (AR-MU2), the stand/3 x 500 sheet paper drawer (AR-D27), or the stand/MPD & 2000 sheet paper drawer (AR-D28) is required. The duplex module/bypass tray (AR-DU4) cannot be installed with the exit tray (AR-TE3) or the saddle stitch finisher (ARFN7). When the duplex module (AR-DU3) is installed, the exit tray (AR-TE3) or the saddle stitch finisher (AR-FN7) is required. Simultaneous installation with the finisher (AR-FN6) is inhibited. The duplex module (AR-DU3) is required. The stand/3 x 500 sheet paper drawer (AR-D27) or the stand/ MPD & 2000 sheet paper drawer (AR-D28) is required. Simultaneous installation with the saddle finisher (AR-FN7) is inhibited. Any one of the multi paper drawer (AR-MU2), the stand/3 x 500 sheet paper drawer (AR-D27), or the stand/MPD & 2000 sheet paper drawer (AR-D28) is required. Any one of the multi paper drawer (AR-MU2), the stand/3 x 500 sheet paper drawer (AR-D27), or the stand/MPD & 2000 sheet paper drawer (AR-D28) is required. The stand/3 x 500 sheet paper drawer (AR-D27), or the stand/ MPD & 2000 sheet paper drawer (AR-D28) is required.
10
AR-FN7
11
Finisher
AR-FN6
12
Mail-bin stacker
AR-MS1
13
AR-FX12
manuals4you.com
B
Printer expansion kit (with HDD)
Related to paper feed unit Multi purpose drawer Stand/3 x 500 sheet paper drawer Stand/MPD & 2000 sheet paper drawer Duplex module/bypass tray Duplex module Scanner module with DSPF Output units Saddle stitch finisher Finisher Mail-bin stacker Exit tray Upper exit tray Right upper exit tray Punch unit Related to extension of functions and others Printer expansion kit
Print server card Print server card (with HDD)
AR-MU2 AR-D27 AR-D28 AR-DU4 AR-DU3 AR-EF3 AR-FN7 AR-FN6 AR-MS1 AR-TE3 AR-TE4 AR-TE5 AR-PN1 *1 *1 *1 *1 *1 *1 *1 *1
PS3 expansion kit Network scanner expansion kit Facsimile expansion kit Fax memory (8 MB) Bar code font
Flash ROM kit
*1 *
1
*1 *1 *1
Data security kit Data security kit Data security kit Data security kit
= Must be installed together. *1 = Any of the units must be installed together. = Cannot be installed together.
ma
ou.c y 4 s l a nu
om
Mail-bin stacker
Duplex module
Punch unit
Exit tray
Finisher
[3] SPECIFICATIONS
1. Basic Specification
A. Base Engine
(1) Form
Console type
(in mm) Paper size A3 B4 A4 B5 A5 Japanese postcard Ledger Legal Foolscap Letter Executive Invoice Com-10 (envelope) C5 (envelope) Monarch (envelope) DL (envelope) ISO B5 (envelope) A 297 257 210 182 148 100 279 216 216 216 184 140 105 162 98 110 176 B 420 364 297 257 210 148 432 356 330 279 267 216 241 229 191 220 250 C 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 D 289 242 202 168 140 92 271 208 208 208 183 132 97 154 90 102 168 E 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
(6) Warm-up
Warm-up time Pre-heat requirement Jam recovery time less than 80 seconds Required Target: about 30 seconds (Under standard condition of 60 seconds left after side cover opening, polygon motor halt)
(10) Noise
B
At working At waiting mode less than 6.8dB less than 5.0dB
(11) Dimensions
External dimensions (W x D x H) 37.9" x 26.2" x 44.4" (963 mm x 665 mm x 1127 mm) (including automatic document feeder) 37.9" x 26.2" (963 x 665 mm) (Include automatic document feeder) Engine: Approx. 85.8 lb (38.9 kg) Desk: Approx. 72.6 lb (32.9 kg) Rack: Approx. 16 lb (7.4 kg) DSPF: Approx. 46 lb (21 kg)
If a printer driver for Windows or Macintosh is used for printing, the printable area will be smaller. The actual printable area depends on the printer driver to be used. AR-M351U/M451U, AR-M355U/M455U SPECIFICATIONS 3 - 1
manuals4you.com
(2) Support OS
Custom PS Windows 95/98/Me Windows NT 4.0 (Service Pack5 or later) Windows Server 2003 Windows 2000 Server Windows 2000 Windows XP Windows 95/98/Me Windows NT 4.0 (Service Pack5 or later) Windows Server 2003 Windows 2000 Server Windows 2000 Windows XP Windows 95/98/Me Windows NT 4.0 (Service Pack5 or later) Windows Server 2003 Windows 2000 Server Windows 2000 Windows XP MacOS 8.6 - 9.2.2, 10.1.5, 10.2 - 10.2.8 (except for Mac OS 10.2.2), 10.3-10.3.3
Custom PCL5e/6(XL)
Dehumidification heater Balance detection Default size setting Mounting/demounting of the tray
PPD
C. Output Equipment
(1) Face-down Exit Tray (included in the base engine)
Output position/ method Output paper capacity Output paper size Face-down output at the upper side of main unit 400 sheets (80g/m sheet) A3, B4, A4, A4R, B5, B5R, A5R 11 " x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11", 8.5" x 11"R, 5.5" x 8.5"R Executive, Japanese post card, Monarch (98 x 191), 8K, 16K, 16KR Com-10 (105 x 241), DL (110 x 220), C5 (162 x 229), ISO B5 (176 x 250) Tracing paper: 52 ~ 59g/m / 14 ~ 15lbs Plain paper: 60 ~ 128g/m / 16 ~ 34lbs Index paper: 176g/m / 47lbs Cover paper: 205g/m / 54 ~ 55lbs Transparency firm Not provided
Duplex
Booklet
2. Specific Function
A. Printer Function
To enable the printer function of the AR-M355U/M455U, the printer expansion kit must be installed.
(1) Platform
IBM PC/AT (Include compatible machine) Macintosh
Invoice on Letter Letter on Ledger A5 on A4 A4 on A3 B5 on B4 Letter on Letter Ledger on Ledger A4 on A4 A3 on A3 B4 on B4 Binding edge Left / top / right N-up 2/4/6/8/9/16 N-up order N-up border Z / Reversed Z / N / Reversed N Yes / No
*1: For printing, PS driver bundled with the Windows is required. *2: Since the function is of PS driver bundled with Windows, specification may vary according to the OS.
b. Paper Input Function Paper size PCL5e PCL6 PS PPD file *1 (for Windows XP)
d. Graphic Function Resolution setting Halftone setting PCL5e PCL6 600dpi Screen frequency 8.0 to 360.0 in 0.1 steps Screen angle 0.0 to 360.0 in 0.1 steps PS PPD file *1 (for Windows XP) 600dpi
Paper type
A3 / B4 / A4 / B5 / A5 / Ledger / Legal / Foolscap / Letter / Executive /Invoice/8k / 16k /COM10/C5/ Monarch/DL Plain Letter Head Pre-Print Pre-Punch Recycle Color Label Heavy Paper Transparency Envelope 7 type
600/300 dpi No
Graphics mode Smoothing Toner save Photo enhancement Negative image Mirror image Zoom
Automatic Tray 1/2/3/4 Bypass-tray Cover Yes/No User can select from 1-sided/2-sided/ No print Insert page Yes/No User can select from 1-sided/2-sided/ No print Transparency No inserts Yes (Blank) Yes (Printed)
Fit to page
*1: For printing, PS driver bundled with the Windows is required. *2: Since the function is of PS driver bundled with Windows, specification may vary according to the OS. e. Font Function Download font PCL5e Bitmap TrueType PCL6 PS Bitmap Type1 TrueType PPD file *1 (for Windows XP) Auto Outline Bitmap Native TrueType (*2)
*1: For printing, PS driver bundled with the Windows is required. c. Paper Output Function Output tray selection PCL5e PCL6 PS PPD file *1 (for Windows XP)
*1: For printing, PS driver bundled with the Windows is required. *2: Since the function is of PS driver bundled with Windows, specification may vary according to the OS. f. Others Function Configuration setting Watermark PCL5e Yes Yes Yes (functionality is limited) Yes Yes Yes Yes Yes Yes Yes Yes PCL6 PS PPD file *1 (for Windows XP)
Center tray Finisher Top tray Offset tray Saddle Stitch Finisher Offset tray Mailbin stacker Mailbin top tray Mailbin (1-7) Duplex module Left tray Staple Finisher No staple 1 staple 2 staples Saddle Stitch Finisher No staple 1 staple 2 staples Offset cancel Yes/No
Line width setting Form overlay Print hold Confidential print Sample print Print accounting Quick sets Auto configuration Job end notification Tandem print
*1: For printing, PS driver bundled with the Windows is required. Carbon print Multienlargement XY zoom
manuals4you.com
PCL5e Yes
PCL6
PS
c. Paper output Function Output tray selection Macintosh PPD file (for Mac OS X ver10.2.8) Center tray Finisher Top tray Offset tray Saddle Stitch Finisher Offset tray Mailbin stacker Mailbin top tray Mailbin (1-7) Duplex module Left tray Finisher No staple 1 staple 2 staples Saddle Stitch Finisher No staple 1 staple 2 staples Yes/No
Duplex
Offset d. Graphic Function Resolution setting Halftone setting Graphics mode Smoothing Toner save Photo enhancement Negative image Mirror image Zoom Fit to page
Macintosh PPD file (for Mac OS X ver10.2.8) 600dpi Yes/No Yes / No Yes/No 1-100000 (*1)
*1: Since the function is of PS driver bundled with Macintosh, specification may vary according to the OS. b. Paper input Function Paper size Macintosh PPD file (for Mac OS X ver10.2.8) A3 / B4 / A4 / B5 / A5 / Japanese Postcard / Ledger / Legal / Foolscap / Letter / Executive / Invoice/ 8K / 16K/ COM10/C5/Monarch/DL Plain / Letter Head / Pre-Print / Pre-Punch / Recycle / Color / Label / Heavy Paper / Transparency / Envelope 7 Automatic Tray 1/2/3/4 Bypass-tray Yes / No (*1) (On OS9, user can select from: No/First Page/Last Page) (*1) No Yes (Blank) Yes (Printed)
Paper type
*1: Since the function is of PS driver bundled with Macintosh, specification may vary according to the OS. e. Font Function Download font Macintosh PPD file (for Mac OS X ver10.2.8) (Selectable only on MacOS9.x.x LaserWriter) (*1)
Transparency inserts
*1: Since the function is of PS driver bundled with Macintosh, specification may vary according to the OS.
f. Others Function Configuration setting Watermark Form overlay Print hold Confidential print Sample print Print accounting Quick sets Auto configuration Job end notification Tandem print Macintosh PPD file (for Mac OS X ver10.2.8) Yes Yes Yes Yes (PIN selection) Yes Yes (OS9: Yes) Yes (The AR-P20/P21 or the AR-NC7/ NC8 is required. (option)) Yes (*1) (Only when the AR-P21 or the ARNC8 is installed. (option))
*1: Since the function is of PS driver bundled with Macintosh, specification may vary according to the OS.
(6) Compatibility
PCL 5e compatibility Target for PCL5e is to be compatible with HP LaserJet 4050. Small margin difference, rendering difference by different font family, default and transfer function difference is not to be included in the compatibility. All the PJL commands are not necessarily included in the compatibility. Target for PCL6 is to be compatible with HP LaserJet 4050. Small margin difference, rendering difference by different font family, default and transfer function difference is not to be included in the compatibility. All the PJL commands are not necessarily included in the compatibility. PostScript is targeted to be compatible with Adobe PostScript as performed in HP LaserJet 4050. Small margin difference, rendering difference by different font family, default and transfer function difference is not to be included in the compatibility.
PCL6 compatibility
PostScript Compatibility
manuals4you.com
Mode Receive function Auto receive Manual receive Memory receive Reduction receive for standard size Scaling receive for specified size Rotation receive Divided receive Duplex receive 2 in 1 receive Address/Domainspecified reception is enabled. Address/Domainspecified reception is disabled. External phone connection Answering phone connection Transfer function at output trouble Auto startup mode Time setting Transmit request Remote transmit Cover function Print at sender Page division Page combination Confidential (machine at the other end) Transmit broadcast direction Transmit message Edge erase Center erase 2 in 1 Card shot Transmit/receive record Transmit/receive result Address/phone directory list Group list ID/Sender's address list) Sender list
Scanner
FAX
Yes
Yes
Yes Yes: To be defined by key operator program Yes: To be defined by key operator program
Yes 50 address Yes 50 address
*1: When HDD is installed. Manual destination entry: Entry other than One-touch, using numeric keys or soft keyboard. In the case of broadcast transmission including fax destination, the resolution level for fax mode is applied. In the case of broadcast transmission with Internet FAX and Scanner destinations, the resolution level of Internet FAX mode is applied. In the case of broadcast transmission, the compression format set with the key operator programs is applied.
Special function
Yes Yes Yes
(7) Functions
Mode Transmit Memory transmit function Scanner Internet FAX Yes FAX
Yes Yes No
Yes Yes No
On-hook Quick online transmit Direct transmit Auto reduction transmit Rotation transmit Scaling transmit
Re-call mode
Error Busy
Book original transmit Long length original transmit Specified pages per file Maximum number of send data Sender name
Yes Yes (Scaling from regular size to regular size only. Some functions does not allow rotation transmit) Yes Yes No. of times/interval is set via key operator program. Yes Yes Yes Yes Yes Max. 800mm Yes
Print administrator address. No Described in the key operation list Yes (Integrated to the memory box list) Yes (Integrated to the memory box list) Yes
Program list Reserved transmit list Memory box list Memory clear notice list Others PC-facsimile transmission
(It's possible that this is output in case of errors.) PC-iFAX PC-FAX Yes (FAX mode only)
Modem speed
*1: S S : A4 / 8.5" x 11" original 5 sheets copy 5sets copy 5sets *2: S D : A4 / 8.5" x 11" original 10 sheets *3: D D : A4 / 8.5" x 11" original 5 sheets (10 pages) copy 5sets
ECM
C. Copy function
(1) Copy Speed
AR-M351U/M355U AR-M451U/M455U Actual Reduction Enlargement Actual Reduction Enlargement 35 35 35 45 45 45 25 35 25 35 25 35 30 45 30 45 30 45
Function APS AMS XY zoom Paper type select Auto tray switching Rotation copy Electronic sort Rotation sort Reserved copy Prior tray setting Recall/register of program Document filing
Yes Yes Yes Yes (By type setting) Yes Yes Yes No Yes No Yes Yes (The AR-P21 or the ARNC8 is required.) No Yes (To be set up by the key operator program) Yes (To be set up by the key operator program) Yes 500 accounts Yes Yes (via network) (The AR-P20/P21 or the AR-NC7/NC8 is required.) No Yes Yes
A4, 8.5" x 11" A4R, 8.5" x 11"R A5R, 5.5" x 8.5"R, Invoice-R B5 B5R, Executive-R B4, 8.5" x 14" A3, 11" x 17" Extra, Envelope
35 25 20 17 17
35 25 20 17 17
35 25 20 17 17
45 30 22 20 20
45 30 22 20 20
45 30 22 20 20
Proof copy Preheat function Auto power shut-off function Account control Process control Tandem copy
Figures in reduction/enlargement are represented by those at the ratio to show slowest speed
manuals4you.com
Special function
Margin shift Edge erase/Center erase Dual page copying Covers/Inserts Transparency insert Centering Multi shot (Nin1) Card shot Pamphlet copy 2-sided copy orientation change Job build Negative image Shading Mirror image Multi-page enlargement Repeat Date stamp Stamp Character stamp Page stamp
Yes Yes Yes Yes Yes No Yes (2 in 1 / 4 in 1) (Centering: Yes) Yes Yes (Centering: Yes) Yes Yes (max.10000 sheets) Yes No Yes No No Yes Yes Yes Yes
600x600
600dpi sending
406.4x391
400x400
600x600
600x600
OR guide display
Rear left side (Print display) Left side OR guide (Print display) Interior side OR guide (Print display)
"
(From the Interior side) 5-1/2, A5R, B5R, A4R/A5, 8.5", B4R/B5, 11", A3R/A4 (From the left side) 5-1/2, A5, B5, A4/A5R, 8-1/2, B5R, 11", A4R, 13", 14", B4R, A3R, 17" Interior side OR Book marks are at A4 and guide 8-1/2 positions. The position available to attach the staple position guide label when the optional finisher (desktop console type) is equipped.
Original tray Center of the tray guide (inscribed symbol) display Original Guide (inscribed symbol)
Original reference position " " Original face-down placement indication " " (From Center) B5R, A4R/A5, 8.5", B4R/B5, 11", A3R/A4 The position available to attach the staple position guide label when the optional finisher (desktop console type) is equipped.
(6) Dimensions
External dimensions (WxDxH) Occupied space dimensions (WxD) Weight 32.4" x 23.9" x 7.48" (824 x 606 x 190 mm) 37.2" x 24.4" (945 x 619 mm) (When the tray is extended) DSPF: Approx. 46.3 lbs (21.0 kg)
(4) DSPF/SPF
Type DSPF One-scan-dual-side scanning method DSPF with OC integrated 45 opm 22.5 opm
Scan speed Standard mode High quality mode Original Center alignment alignment Original size A3, B4, A4, A4R, B5, B5R, A5, A5R 11"x17", 8.5"x14", 8.5"x13", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R, 8K, 16K, 16KR (Long size original up to 800mm in FAX, e-mail and iFAX mode) Original 50~128g/m, 15~34lbs paper weight Original Max. 50 sheets stack (Max. 30 sheets for A3, B4,11" x 17",8.5" x 14") capacity (Max. 15 sheets for A3, B4, 11" x 17", 8.5" x 14" over 105g/m) or, Total thickness less than Max. 6.5mm (at 50 to 80g/m, 15 to 21lbs) Max. 5.0mm (at 80 to 128g/m, 21 to 34lbs) Not Transparency film, secondary original paper, transportable tracing paper, carbon paper, thermal paper, original type original with crumple/crimp/rip, original with attachment/clipping, original with many punch holes (with 2 or 3 holes acceptable), original preprinted with ink-ribbon, Documents with considerable curl. Original size Provided detection Sizes to be Automatic (one detection unit to be used with detected software modification by destination) Inch-1 11" x 17", 8.5" x 14", 8.5" x 11", 8.5" x 11"R, 5.5" x 8.5", A4, A3 Inch-2 11" x 17", 8.5" x 13", 8.5" x 11", 8.5" x 11"R, 5.5" x 8.5", A4, A3 AB-1 A3, B4, A4, A4R, B5, B5R, A5, A3, 8.5" x 11", 11" x 17" 216 x 330 mm AB-2 A3, B4, A4, A4R, B5, B5R, A5, 8.5" x 11", 11" x 17", 216 x 330 mm AB-3 8K, A4, A4R, B4, 16K, 16KR, 8.5" x 11", 216 x 330 mm
(8) Key
Mode Job status key selection area Document filing key (* online display LED/data in-memory display LED) Image send key (busy display LED/data in-memory display LED) Copy mode key User definition key Basic input Start key area CA key 10-key Clear key key #/P key * For printer
manuals4you.com
B. Taiwan (Aurora)
No. Item Content 1 Toner Cartridge (Black) Toner CA with IC Chip (Toner; Net Weight 750g) 2 Developer (Black) Developer (Developer; Net Weight 500g) 3 Drum Drum x 10 x 10 x1 Life 350k (35k x 10) 1,000k (100K x 10) 200k Model name AR-455ET AR-455LD AR-455DM Remarks *Life : A4 size at Area Coverage 6%
C. Asia
No. Item Content 1 Toner Cartridge (Black) Toner CA with IC Chip (Toner; Net Weight 750g) 2 Developer (Black) Developer (Developer; Net Weight 500g) 3 Drum Drum x 10 x 10 x1 Life 350K (35K x 10) 1,000K (100K x 10) 200K Model name AR-455CT AR-455CD AR-455DR Remarks *Life: A4 size at Area Coverage 6%
D. Middle East/Africa/Israel/Philippines
No. Item Content 1 Toner Cartridge (Black) Toner CA with IC Chip (Toner; Net Weight 750g) 2 Developer (Black) Developer (Developer; Net Weight 500g) 3 Drum Drum x 10 x 10 x1 Life 350K (35K x 10) 1,000k (100K x 10) 200k Model name AR-455ET AR-455CD AR-455DR Remarks *Life : A4 size at Area Coverage 6%
E. Hong Kong
No. Item Content 1 Toner Cartridge (Black) Toner CA with IC Chip (Toner; Net Weight 750g) 2 Developer (Black) Developer (Developer; Net Weight 500g) 3 Drum Drum x 10 x 10 x1 Life 350K (35K x 10) 1,000K (100K x 10) 200k Model name AR-455CT-C AR-455CD-C AR-455DR-C Remarks *Life : A4 size at Area Coverage 6%
F. China
No. Item Content 1 Toner Cartridge (Black) Toner CA with IC Chip (Toner; Net Weight 750g) 2 Developer (Black) Developer (Developer; Net Weight 500g) 3 Drum Drum x1 x1 x1 Life 35k 100k 200k Model name AR-456ST-C AR-455SD-C AR-455DR-C Remarks *Life : A4 size at Area Coverage 6%
2 3
AR-SC1 AR-SC2
Cartridge for AR-FN4 Common with cartridge for AR-FN6 Common with cartridge for AR-FN7
Note: The other maintenance parts which are not listed above are registered as service parts.
2 3
AR-SC1 AR-SC2
Cartridge for AR-FN4 Common with cartridge for AR-FN6 Common with cartridge for AR-FN7
Note: The other maintenance parts which are not listed above are registered as service parts.
manuals4you.com
C. Hong Kong
No. Item 1 200K PM kit Content Cleaner blade Drum separation pawl MC unit *1 Toner receiving seal Side malt F Side malt R Transfer roller Discharger plate Paper dust removing unit DV blade DV side seal F DV side seal R Upper heat roller Fusing separation pawl (Upper) Lower heat roller Fusing separation pawl (Lower) Cleaning roller Bearing Staple cartridge Staple cartridge Life Model name Remarks x1 200K AR-451KA *1: Screen grid, charging plate, MC cleaner unit are included. x4 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x4 x1 x2 x1 x2 x 3 3000 times x 3 AR-SC1 Cartridge for AR-FN4 Common with cartridge for AR-FN6 x 3 5000 times x 3 AR-SC2 Common with cartridge for AR-FN7
2 3
Note: The other maintenance parts which are not listed above are registered as service parts.
D. China
No. Item 1 200K PM kit Content Cleaner blade Drum separation pawl MC unit *1 Toner receiving seal Side malt F Side malt R Transfer roller Discharger plate Paper dust removing unit DV blade DV side seal F DV side seal R Upper heat roller Fusing separation pawl (Upper) Lower heat roller Fusing separation pawl (Lower) Cleaning roller Bearing Staple cartridge Staple cartridge Life Model name Remarks x1 200K AR-451KA *1: Screen grid, charging plate, MC cleaner unit are included. x4 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x4 x1 x2 x1 x2 x 3 3000 times x 3 AR-SC1 Cartridge for AR-FN4 Common with cartridge for AR-FN6 x 3 5000 times x 3 AR-SC2 Common with cartridge for AR-FN7
2 3
Note: The other maintenance parts which are not listed above are registered as service parts.
C. Developer cartridge
The lot number is of 8 digit, and each digit indicates as follows. The lot number shall be printed on the bag. 1 1 2 3/4 5/6 7 8 2 3 4 5 6 7 8
5/6 7
8/9 10
Humidity (%)
Number For this model, this digit is 2. Alphabet Indicates the model conformity code. T for this model. Number Indicates the end digit of the production year. Number or X, Y, Z Indicates the production month. X stands for October, Y November, and Z December. Number Indicates the production day on the month. Number or X, Y, Z Indicates the month of packing. X stands for October, Y November, and Z December. Number Indicates the day of the month of packing. Alphabet Indicates the production factory. "A" for Nara Plant.
Alphabet Indicates the production factory. Number Indicates the production year. Number Indicates the production month. Number Indicates the production day. Hyphen Number Indicates the production lot.
3. Environmental conditions
A. Operating conditions
30 85%
85
B. Toner cartridge
The lot number is of 7 digits, and each digit indicates as follows. The lot number shall be printed in the position shown in the figure. 1 1 2 3 4 5/6 7 2 3 4 5 6 7
35
60%
20
Version number (A - sequentially revised) Numeral figure Indicates the end digit of the production year. Alphabet Indicates the production factory. (B for SOCC) Destination code Numeral figures Indicates the production day. Numeral figure or X, Y, Z Indicates the production month. X stands for October, Y November, and Z December.
10
Temperature
35
(Without dew condensation)
B. Storage conditions
90
Humidity (%)
20 -10
Temperature
40
Heat seal
Aluminum bag
manuals4you.com
11
No. 1 2 Name Bypass tray Exit tray Function This tray can also be used for special papers including transparency film. The tray is extendable to support large size paper. Extend the tray when 11" x 17", 8-1/2" x 14", 8-1/2" x 13", A3 or B4 paper is being used. This automatically feeds and scans multiple sheet originals. Both sides of two-sided originals can be scanned at once. Module for two-sided printing Finished sheets are deposited here. Provides support for large size paper. Open to add toner. Press to turn power on and off. This paper feed unit contains an upper multi-purpose drawer and two lower drawers each of which can hold a maximum of 500 sheets of 20 lbs. (80 g/m2) paper. This paper feed unit contains an upper multi-purpose drawer and a lower drawer which can hold a maximum of 2000 sheets of 20 lbs. (80 g/m2) paper. Up to 500 sheets of 20 lbs. (80 g/m2) paper can be loaded. Also special papers such as envelopes (standard sizes only) and postcards can be set.
13
Note Option (AR-DU4) Option (AR-DU4/AR-TE3) Option (AR-DU3/DU4) Option (AR-AR-TE4) Option (AR-D27) Option (AR-D28) Option (AR-MU2)
3 4 5 6 7 8 9 10 11
Automatic document feeder Duplex module Upper paper output area Upper exit tray extension Operation panel Front cover Power switch Paper tray 1 Stand/3 x 500 sheet paper drawer
12
13
2. Interior
1 2 3 4
5
No. 1 2 3 4 5 6 Name Duplex module side cover Side cover latch Fusing unit Toner cartridge (drum/toner cartridge) Photoconductive drum Cartridge lock lever
Function Open when a misfeed has occurred in the duplex module. Push up to open the side cover when a misfeed has occurred in the main unit. Lift up to open the side cover when a misfeed has occurred in the main unit. CAUTION: The fusing unit is hot. Take care in removing misfed paper. The toner cartridge must be replaced when indicated on the operation panel. Images are formed on the photoconductive drum. NOTE: Do not touch or damage the photoconductive drum. When replacing the drum, toner or developer cartridge, turn down this lever and pull it out.
manuals4you.com
3. Operation panel
When the printer expansion kit (with HDD) print server card (with HDD) is installed. 2 3
4
No. 1 Name Touch panel
10
11
Function The machine status, messages and touch keys are displayed on the panel. The document filing, copy, network scanner*2, and fax*3 functions are used by switching to the screen for the desired function. Use to change modes and the corresponding display on the touch panel. [PRINT] key/[DOCUMENT FILING] key*1 Press to select the print/document filing*1 mode. [IMAGE SEND] key/LINE indicator/DATA indicator Press to change the display to network scanner mode*2 or fax mode*3. [COPY] key Press to select the copy mode. READY indicator Print data can be received when this indicator is lit. DATA indicator Lights up or blinks when print data is being received. Also lights up or blinks when printing is being performed. Press to display the current job status. This is used to store, edit, and delete user names and folder names for the document filing function*1, and to configure the key operator programs and printer configuration settings. Use to enter numeric values for various settings. This key is used in copy mode, document filing mode*1, network scanner mode*2, and fax mode*3. This is used as a program key when using the copy function, and to dial when using the fax function*3. This key is used in copy mode, document filing mode*1, network scanner mode*2, and fax mode*3. Use this key to start copying in copy mode, scan a document in network scanner mode*2, or scan a document for transmission in fax mode*3. This key is used in copy mode, document filing mode*1, network scanner mode*2, and fax mode*3. Use the key to cancel settings and perform an operation from the initial machine state.
4 5 6 7 8 9 10 11
[JOB STATUS] key [CUSTOM SETTINGS] key Numeric keys [ ] key ([ACC.#-C] key) [#/P] key [C] key (Clear key) [START] key [CA] key (Clear all key)
*1: When the printer expansion kit (with HDD)/print server card (with HDD) is installed. *2: When the network scanner option is installed. *3: When the fax option is installed.
4. Job status screen (common to print, copy, fax, network scan and Internet fax)
This screen is displayed when the [JOB STATUS] key on the operation panel is pressed. This screen can be used to display the "JOB QUEUE" (showing stored jobs and the current job) or the "COMPLETE" job list (showing finished jobs). This screen can be used to check jobs, interrupt a job in progress to perform another job, and cancel a job.
"JOB QUEUE" screen
JOB QUEUE COPY COPY Suzuki 066211221 PRINT JOB SETS / PROGRESS STATUS COPYING PAPER EMPTY
DETAIL DETAIL 1/1
*1
JOB QUEUE COMPLETE
WAITING WAITING
FAX JOB
INTERNET-FAX
INTERNET-FAX
3
No. Name 1 Job list
8 9 10
11
Function The displayed jobs in the job list are themselves operation keys. To cancel printing or to give a job the highest print priority, touch the relevant job key to select the job and execute the desired operation using the keys described in 8 and 9. This shows the current job and the jobs waiting to be run. The icons to the left of the jobs in the queue show the job mode. The document filing reprint job icon is highlighted. Note that the icon does not become highlighted during retransmission of a fax/image transmission job. Print mode Copy mode Scan to FTP job Fax reception job i-Fax reception job Scan to Sharpdesk job PC-Fax send job PC-Internet Fax send job E-MAIL/FTP mode Scan to e-mail job Fax mode Fax send job Internet Fax mode i-Fax send job
*1: "PAPER EMPTY" in the job status display When a job status display indicates "PAPER EMPTY", the specified paper size for the job is not loaded in any of the trays. In this case, the job will be suspended until the required paper is loaded. Other stored jobs will be printed (if possible) until the required paper is loaded. (Other jobs will not be printed if the paper runs out during printing.) If you need to change the paper size because the specified paper size is not available, touch the current job key to select it and then touch the [DETAIL] key described in 10. 2 Mode select key This switches the job list display between "JOB QUEUE" and "COMPLETE". "JOB QUEUE": Shows stored jobs and the job in progress. "COMPLETE": Shows finished jobs. Files saved using the "FILE" and "QUICK FILE" functions and finished broadcast transmission jobs appear as keys in the finished job screen. The "FILE" or "QUICK FILE" job keys in the finished job screen can be touched, followed by the [CALL] key, to call up a finished job and print or transmit it. A finished broadcast transmission job key can be touched followed by the [DETAIL] key to check the result of the transmission. 3 [PRINT JOB] key This displays the print job list of print mode (copying, printing, fax reception, Internet fax reception, and self printing). 4 [E-MAIL/FTP] key This displays the transmission status and finished jobs of scan mode (Scan to e-mail, Scan to FTP, and Scan to SharpDesk) when the network scanner option is installed. 5 [FAX JOB] key This displays the transmission/reception status and finished jobs of fax mode (fax and PC-Fax) when the fax option is installed. 6 Display switching keys Use to switch the page of the displayed job list. 7 [INTERNET-FAX] key This displays the transmission/reception status and finished jobs of Internet fax mode and PC Internet fax mode when the network scanner option is installed. 8 [STOP/DELETE] key Use to cancel or delete the current job or delete the stored job. Note that printing of received faxes and received Internet faxes cannot be canceled or deleted. 9 [PRIORITY] key Touch this key after selecting a stored job in this [JOB QUEUE] list to print the job ahead of the other jobs. Note that a job in progress cannot be interrupted if it is an interrupt copy job or if it is a list print job. 10 [DETAIL] key This shows detailed information on the selected job. Files saved using the "FILE" and "QUICK FILE" functions and finished broadcast transmission jobs appear as keys in the finished job screen. A Quick File in the finished job screen or the [Filing] key can be touched, followed by the [CALL] key, to call up a finished job and print or transmit it. A finished broadcast transmission job key can be touched followed by the [DETAIL] key to check the result of the transmission. 11 [CALL] key When this key is touched after selecting a job in the COMPLETE job status screen (a job stored using the FILE or QUICK FILE keys of the document filing function), the "JOB SETTINGS" menu screen appears to let you resend or reprint the finished job. AR-M351U/M451U, AR-M355U/M455U EXTERNAL VIEWS AND INTERNAL STRUCTURES 5 - 4
manuals4you.com
17 SPOD
15
14
13
12 11 10
No. 1 2 3 4 5 6 7 8 9
Name CIS unit Original resist roller Original resist front sensor (SPPD) Original set sensor (SPED) Original take-up sensor Original length sensor 1 (SPLS1) Original length sensor 2 (SPLS2) CCD/lens unit Original feed roller
No. 10 11 12 13 14 15 16 17
Name Copy lamp base unit No. 1 mirror Copy lamp (Xenon) Mirror base unit No. 3 mirror No. 2 mirror Original exit roller Original exit sensor
B. Engine
POD1 POD2 POD3 21 22 23 24
20 15 16 17 26 3 1 8 6 9 5 PPD1 10 11 25 4 2 18 19
12
13
PED TUD 7
14
No. 1 2 3 4 5 6 7 8 9 10 11 12 13
Name OPC drum Main charger Cleaning blade LSU Developing unit Magnet roller Toner hopper Transfer roller Resist roller Paper transport roller Machine tray (Paper tray1) paper feed roller Machine tray (Paper tray1) separation roller Machine tray (Paper tray1) take-up roller
No. 14 15 16 17 18 19 20 21 22 23 24 25 26
Name Machine tray (Paper tray1) rotating plate Upper heat roller Pressure roller Heater lamp Thermistor (RTH1 / RTH2) Thermostat Fusing back roller Reverse gate Paper exit roller Full detection lever Printer control PWB Power supply unit Cleaning roller
6. Switch, Sensor
A. Scanner unit
4 3 2 1 8 5 6 7
12 11 10
1 2 3 4 5 6 7 8 9 10 11 12
Code SPPD SCOV SPED OCSW ORS-LED SPLS1 SPLS2 SPFVR ORS-PD SOCD SPOD MHPS
Name SPF original resist front sensor SPF paper feed cover sensor SPF original set sensor OC open/close sensor Original size sensor PWB (Light emitting side) SPF original length sensor 1 SPF original length sensor SPF original width detection volume PWB Original size sensor PWB (Light receiving side) SPF open/close sensor SPF original exit sensor Mirror home position sensor
Active condition
B. Engine
5.POD3 4.POD2
2.DSW-L 3.POD1
10.MAIN SW
Code 1 2 3 4 5 6 7 8 9 10 DSW-F DSW-L POD1 POD2 POD3 PPD1 TCS LUD PED MAIN SW
Function/Operation Front door open/close detection Left door open/close detection Paper exit detection Paper exit detection Paper exit detection Full Paper transport detection Toner concentration sensor Paper feed cassette upper limit detection Paper feed cassette paper empty detection Power switch
Active condition H= Door open H=Door open L= Paper detection L= Paper detection L= Paper detection L= Paper detection H= Upper limit detection L= Paper empty detection
manuals4you.com
7. PWB
A. Scanner unit
1 6 2 3 13 4
5 12 11 10 9 8 7
No. 1 2 3 4 5 6 7 8 9 10 11 12 13
Name SPF control PWB Original size detection PWB (Light emitting side) CCD PWB (in lens unit) (The lens unit cannot be disassembled.) SPF original width detection volume PWB MFP operation PWB Scanner control PWB LVDS PWB Original size sensor (Light receiving side) CIS unit (in CIS unit) (The CIS unit cannot be disassembled.) CIS interface PWB (in CIS unit) (The CIS unit cannot be disassembled.) Scanner interface PWB CIS control PWB CL inverter PWB
Function/Operation SPF control Original size detection when using the table glass Image scan (Table glass/SPF surface) SPF original width detection Panel operation control Scanner unit control LCD signal relay Original size detection when using the table glass Image scan (SPF back surface) CIS signal AD conversion process Scanner unit and connection of scanner control PWB CIS unit control and image process Inverter for copy lamp
B. Engine
1
2 7 11 8 6 10 13 9 12 3 5
No. 1 2 3 4 5 6 7 8 9 10 11 12 13
Name PRT controller PCU PWB Power supply unit LD PWB (Inside LSU) Mother PWB Reactor PWB (200V only) / Filter PWB (Taiwan only) BD PWB High voltage resistor PWB Cassette detection PWB Drawer PWB High voltage PWB Fuse PWB Relay PWB
Function/Operation Image process, image data communication control Overall control of the machine and options DC power supply Laser ON control (Inside LSU: LSU cannot be disassembled.) Signal interface between PCU and the controller Noise filter Laser control (Inside LSU: LSU cannot be disassembled.) High voltage load adjustment Paper cassette control Fan control High voltage power supply Protection of the machine when an abnormal power is supplied. HDD back up
7 6
No. 1 2 3 4 5 6 7
Name SPF motor SPF original resist clutch SPF original feed clutch SPF original stopper solenoid Mirror motor SPF original feed solenoid Stamp solenoid
Function/Operation Original transport in SPF scan SPF original scan timing adjustment SPF original feed roller drive SPF original stopper gate drive Mirror base copy lamp base drive SPF original feed unit drive Finish stamp drive (Option AR-SU1 required)
B. Engine
10.CFM2 3.POM 13.PSPS 6.VFM2 16.CNTFAN
17.PM
7.VFM1
Code 1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 DM MM POM TM LUM VFM2 VFM1 CFM1 CFM2 CPFC TRC PSPS RRC HDDFAN CNTFAN PM
Function/Operation Drum motor Main motor Paper exit motor Toner motor Lift-up motor Heat exhaust fan motor Cooling fan motor Suction fan motor Ozone exhaust fan motor Paper cassette paper feed clutch Paper transport clutch Separation solenoid Resist roller clutch Cooling fan motor (for HDD) Cooling fan motor (for controller) Polygon motor
Type Brushless motor Brushless motor Stepping motor Synchronous motor Synchronous motor Fan motor Fan motor Fan motor Fan motor
manuals4you.com
Main unit
Duplex device
Start of installation
Controller board, facsimile unit or other electric devices installed? No [Electrical setting/adjustment] Install duplex/pypass device.
Yes
Main unit
Install controller board, facsimile unit or other electric devices. AR-FX12/AR-MM9 AR-P20 AR-P21 AR-NC7 AR-NC8 AR-PK6 AR-NS3 Extended memory
1) Installation of driver software, setting, and operation check Main unit/AR-EF3/AR-FX12/AR-P20/AR-P21 AR-NC7/AR-NC8/AR-PK6/AR-NS3 2) Paper guide position adjustment/off center adjustment
AR-MU2/AR-D27/AR-D28/ AR-DU3/AR-DU4
No Install finishing device. Finishing device installed? Yes AR-MS1 AR-FN6 AR-FN7 AR-PN1A / B / C / D
End
No
When installing a paper feeding device or a duplex/bypass device, be sure to reattach the rear cabinet, the AC inlet cover, and the harness cover of the main unit at the end of installation as needed. When installing a controller board, a facsimile unit, and other electric devices, be sure to install them at a time. Only off center adjustment is needed for AR-DU3.
For installation of an option unit, refer to the Service Manual of the option unit.
Check the following items are included in the package. (North America) AR-M355U/M455U AR-M355U/M455U + AR-P20 + AR-P21 Operating Manual (Copier/Key Operation) Install Guide (PCL, PC) CD-ROM (Printer) CD-ROM (NIC) Maintenance card/Maintenance case Key Sheet (PRINT display) AR-M355U/M455U (Europe) AR-M351U/M451U AR-M351U/M451U + AR-NC7 + AR-NC8 Operating Manual (Copier/Key Operation) *1 CD-ROM (Printer) *2 CD-ROM (NIC) Maintenance card/Maintenance case Installation Report/Other Key Sheet (PRINT display) *1 Key Sheet (PRINT display) Key Sheet (DOCUMENT FILING display) Key Sheet (DOCUMENT FILING display) *1 AR-M351U/M451U *1: For the Europe model, this manual is included in the operation manual kit for language support. The standard language for the key sheet is English. To support local language, attach the key sheet. *2: For the Europe model, two driver CD's are provided for language support.
23-5/8" (60cm)
3. Unpacking procedure
A. AR-M355U/M455U (North America), AR-M351U/M451U (Europe)
Check the following items are included in the package. AR-M351U/M451U AR-M351U/M451U + AR-NC7 + AR-NC8 Operating Manual (Copier/Key Operation) *1 CD-ROM (Printer) *2 CD-ROM (NIC) Maintenance card/Maintenance case Installation Report/Other Key Sheet (PRINT display) *1 Key Sheet (PRINT display) Key Sheet (DOCUMENT FILING display) Key Sheet (DOCUMENT FILING display) *1 AR-M351U/M451U
manuals4you.com
3) Remove the cushioning materials from the right and left of the front side.
4) Remove the locking tape from the right and left sidesof the tray. Then, Remove the top of the carton and lower the plastic bag covering the machine while the machine is still on the carton base. 5) Remove the packing tape from the paper tray, pull out the paper tray until it stops and remove it by tilting it upward.
Note: In advance to installation of the machine, the paper feed option units (AR-D27/AR-D28/AR-MU2) should have been installed.
A. AR-D28
<Before installation> Start installation after checking that the DATA and COMMUNICATION indicators on the operation panel are neither lit nor blinking.
Rear side
Note: The center of gravity of the machine lies in the left side when viewed from the Back of machine. When lifting the machine, be careful not to drop it.
<Parts included>
Front mounting plates: 2 pcs. Rear mounting plates: 2 pcs. Screws (M4x6): 4 pcs.
1) Turn off the main switch of the main unit of the printer. Turn the main switch located on the front side of the printer to the "OFF" position. Then remove the power plug from the outlet.
4) Connect the main unit to the stand/paper drawer. <1> Attach the rear mounting plates using a supplied screw for each.
Rear mounting plate
"OFF"
Screw Rear mounting plate Screw
2) Attach the adjusters and adjust them. <1> Insert the left adjusters to the stand/paper drawer. <2> Turn the each adjusters to lower them until they touch the floor.
Desk frame
Caution: Insert the rear mounting plates under the desk frame. <2> Pull out the upper paper tray of the stand/paper drawer until it stops and attach the front mounting plates using a supplied screw for each. Then, remove the lock of the paper tray and close the tray.
2 2 2 1
Front mounting plate
Screw
Caution: The lower tray cannot be pulled out unless the adjuster is lowered to the specified position. 3) Put the main unit of the printer on the stand/paper drawer. <1> Pull out the paper tray of the main unit until it stops and then remove it by lifting both ends of the tray.
Front mounting plate
Screw
<2> Hold the main unit of the printer at the positions shown in the illustration and put the main unit on the stand/paper drawer so that the front side and the left side of the main unit are aligned to those of the stand/paper drawer.
Front side
5) Connect the power supply I/F harness to the PCU PWB of the main unit of the printer. <1> Remove the screw that fixes the harness cover of the main unit of the printer and slide the harness cover up to remove it. Process the harness cover as shown in the illustration.
Screw
Rear side
Caution: For installation of the main unit, it must be held by two persons and installed without haste.
Cut out.
Harness cover
manuals4you.com
<2> Connect the power supply I/F harness connector (red, 22pin) to CN11 (red connector) of the PCU PWB of the main unit of the printer.
Connector
CN11
B. AR-D27
<Before installation> Start installation after checking that the DATA and COMMUNICATION indicators on the operation panel are neither lit nor blinking.
Connect the connector (white, 4pin) of power supply I/F harness to the I/F connector (white, 4pin) of the main unit. Remove the M4 screw shown in the illustration, insert the circle terminal of ground harness, and it fixes again.
<Parts included>
1) Turn off the main switch of the main unit of the printer. Turn the main switch located on the front side of the printer to the "OFF" position. Then remove the power plug from the outlet. <3> Reattach the power supply I/F harness cover to its original position and fix it with the removed screw. At this time, ensure that the power supply I/F harness are arranged as shown in the illustration. Fix the harness securely to the wire saddle.
Screw Power supply I/F harness
"OFF"
2) Attach the adjusters and adjust them. <1> Insert the left adjusters to the stand/paper drawer. <2> Turn the five adjusters to lower them until they touch the floor.
Harness cover
2
6) Attach the paper guides to the lower tray (large capacity tray) and set the size. Refer to "Setting and adjustment" described later.
If another peripheral device must be installed, carry out the fol-
lowing step at the end of the installation work. 7) Adjust the position of the paper guides of the upper paper tray of the stand/paper drawer. Refer to "Setting and adjustment" described later. 8) Carry out the off center adjustment.
Caution: The lower tray cannot be pulled out unless the adjuster is lowered to the specified position. 3) Put the main unit of the printer on the stand/paper drawer. <1> Pull out the paper tray of the main unit until it stops and then remove it by lifting both ends of the tray.
<2> Hold the main unit of the printer at the positions shown in the illustration and put the main unit on the stand/paper drawer so that the front side and the left side of the main unit are aligned to those of the stand/paper drawer.
Front side
Rear side
5) Connect the power supply I/F harness to the PCU PWB of the main unit of the printer. <1> Remove the screw that fixes the harness cover of the main unit of the printer and slide the harness cover up to remove it. Process the harness cover as shown in the illustration.
Screw
Caution: For installation of the main unit, it must be held by two persons and installed without haste. 4) Connect the main unit to the stand/paper drawer. <1> Attach the rear mounting plates using a supplied screw for each.
Cut out.
Rear mounting plate
Harness cover
Screw
<2> Connect the power supply I/F harness connector (red, 22pin) to CN11 (red connector) of the PCU PWB of the main unit of the printer.
Mounting plate
Connector
CN11
Desk frame
Caution: Insert the rear mounting plates under the desk frame. <2> Pull out the upper paper tray of the stand/paper drawer until it stops and attach the front mounting plates using a supplied screw for each. Then, remove the lock of the paper tray and close the tray. Remove the locks of the middle tray and the lower tray similarly.
Connect the connector (white, 4pin) of power supply I/F harness to the I/F connector (white, 4pin) of the main unit. Remove the M4 screw shown in the illustration, insert the circle terminal of ground harness, and it fixes again.
Screw
Screw
manuals4you.com
<3> Reattach the harness cover to its original position and fix it with the removed screw. At this time, ensure that the power supply I/F harness is arranged as shown in the illustration. Fix the harness securely to the wire saddle.
2) Put the main unit of the printer on the multi purpose drawer. <1> Pull out the paper tray of the main unit until it stops and then remove it by lifting both ends of the tray.
<2> Hold the main unit of the printer at the positions shown in the illustration and put the main unit on the multi purpose drawer so that the front side and the left side of the main unit are aligned to those of the multi purpose drawer.
Front side
Rear side
C. AR-MU2
Caution: For installation of the main unit, it must be held by two persons and installed without haste. 3) Connect the main unit of the printer to the multi purpose drawer. <1> Attach the rear mounting plates using a supplied screw for each.
<Parts included>
Screw Screw Rear mounting plate
Mounting plate
1) Turn off the main switch of the main unit of the printer. Turn the main switch located on the front side of the main unit to the "OFF" position. Then, remove the power plug of the main unit from the outlet.
Tray frame
"OFF"
<2> Pull out the paper tray of the multi purpose drawer until it stops and attach the front mounting plates using a supplied screw for each. Then, remove the lock of the paper tray and close the tray.
<3> Remove the filament tape that secure the the power supply I/ F harness.
<1> Remove the screw that fixes the harness cover of the main unit of the printer and then slide the harness cover up to remove it. Process the harness cover as shown in the illustration.
Screw
<3> Reattach the paper tray of the main unit of the printer.
Cut out.
4) Remove the multi rear cabinet. <1> Remove the two screws that secure the multi rear cabinet.
Screw
Harness cover
<2> Connect the connector of the relay harness of the multi purpose drawer to the connector of the PCU PWB of the main unit of the printer.
CN10
Multi rear cabinet Screw
Connector
<2> Remove the two screws that secure the Harness protection sheet.
manuals4you.com
<3> Connect the connector (white, 4pin) of power supply I/F harness to the I/F connector (white, 4pin) of the main unit. Connect the power supply I/F harness connector (red, 22pin) to CN11 (red connector) of the PCU PWB of the main unit of the printer. Remove the M4 screw shown in the illustration, insert the circle terminal of ground harness, and it fixes again.
6. Unpacking and installation of the rack (AR-RK2) (Except for North America/ Europe)
Connector
CN11
tion manual. 6) Attach the harness cover. Reattach the harness cover to its original position and fix it with the removed screw. At this time, ensure that the power supply I/F harness is arranged as shown in the illustration. Fix the harness securely to the wire saddle.
1) Attach the rack to the desk unit. # Be sure to identify the left and the right racks. Refer to the figure below. Insert the rack boss into the rack mounting hole (made by removing the mold of the desk unit), and fix each rack with two fixing screws (M5 x 70).
Screw
Cam Rack sheet Rack with the rack sheet attached to it Rack with the cam attached to it
lowing step at the end of the installation work. 7) Adjust the position of the paper guides of the paper tray. Refer to "Setting and adjustment" described later. 8) Carry out the off center adjustment.
Boss
7. Unpacking and installation of the AR-EF3 (Except for North America/ Europe)
3) Fix the scanner unit. Fix the scanner unit which is on the rack with the fixing screw (M4 x 8), and fix it to the rack with the M4 step screw (long, short x 2).
M4 stepped screw
Reference Reference
4) Remove the fixing tape for scanner packing and remove the fixing screw. Remove the pack fixing tape and the fixing screws which are fixing the scanner unit, and remove the packing note.
Tray (1 pc.)
5) Connect the cable. 1) Turn off the main switch of the main unit of the printer. Turn the main switch located on the front side of the printer to the "OFF" position. Then remove the power plug from the outlet. Connect the scanner unit connector with the printer connector, and fix the connectors with two screws attached to the connector.
"OFF"
2) Put the scanner unit on the rack. Hold the handle of the scanner unit, and put the scanner unit on the rack from the front side of the rack as shown in the figure. Slowly slide the scanner unit until it is brought into contact with the rack and stopped.
Scanner cable
Screws
Note: When inserting the connector, be careful not to break the pins, and connect according to the guide. 6) Attach the paper exit tray. Attach the paper exit tray to the scanner unit as shown in the figure.
Rack
Scanner unit
manuals4you.com
4) While rotating the MG roller, supply developer into the developer cartridge evenly. Note that the MG roller must be rotated in the arrow direction as shown in the figure below. Use of a metal scale or a screwdriver (-) facilitates the procedure. Note: Before opening the developer seal, shake it 4 or 5 times.
5) Attach the top cover to the developer cartridge and install the cartridge to the machine.
2) Insert a new toner cartridge. Push the cartridge in until it locks securely into place.
2) While pressing the paper holding plate, remove the fixing pin.
3) Put paper in the tray, and close the paper feed tray.
D. Paper setting
1) Pull out the first stage paper feed tray. Slowly pull out the tray until it stops.
Press [START] key. Press [CUSTOM SETTINGS] key, and the operation is stopped immediately or after 2 min.
SIMULATION 25-2 AUTOMATIC DV ADJUSTMENT. EXECUTING. HUMIDITY AREA: 70.0 - 72.5 TEMPERATURE AREA: 70.0 - 72.5 DEVE REFERENCE: 118
6) Press the [START] key, and the automatic developer adjustment will be performed. During execution of the automatic developer adjustment, EXECUTING... is displayed and the toner sensor value is indicated on the LCD. (DEVE REFERENCE) AR-M351U/M451U, AR-M355U/M455U UNPACKING AND INSTALLATION 6 - 12
manuals4you.com
7) After about 2 min, the adjustment value is stored in the machine. Check that the mode was normally completed. Normal end: Returns to the initial window (PRESS START display).
Abnormal end: Returns to the initial window (PRESS START display), and indicates the trouble display (TROUBLE! EE-**). In case of an error end, remove the cause of the error, and execute the automatic developer adjustment again. 8) Turn off/on the power, and the machine returns to the normal mode and enters the warm-up mode. Case of Fig. 2
For one scale (one groove), shift by 0.5mm. After shifting the cam, tighten the cam A fixing screw (M3 x 12). Make a copy again and check to confirm that there is no distortion on the image. After adjustment, tighten the fixing screw (M3 x 12) and the scanner fixing screw (M4 x 8). Attach the decoration seal to the screw hole.
6mm
Reference
15mm
<North America only> AR-M355U/ AR-M355U/ AR-M355U/ M455U M455U + AR-P20 M455U + AR-P21
<English area other than North America> AR-M351U/ M451U Key Sheet (PRINT display) AR-M351U/ M451U + AR-NC7 AR-M351U/ M451U + AR-NC8
<Other than English area in Europe> AR-M351U/ M451U Key Sheet (PRINT display) Key Sheet (DOCUMENT FILING display) AR-M351U/ M451U + AR-NC7 AR-M351U/ M451U + AR-NC8
2) Insert the handle into the left rack notch diagonally upward as shown in the figure.
Reference Reference
3) Attach the screw which was removed in procedure 1) to secure the handle.
4) Lift the rear edge A of the handle to engage the head with the rack.
2 2 2 1
of the machine. Note: If the adjusters are not lowered to the specified positions, the lower stage tray cannot be pulled out.
manuals4you.com
When 100K 200K 300K 400K 500K 600K 700K 800K Remark calling Drum peripheral Drum L L L L Replace at 200K or 1 year. Cleaner blade L L L L Toner reception seal L L L L Side molt F L L L L Side molt R L L L L Transfer roller L L L L Discharge plate L L L L TR bearing (F/R) L L Transfer roller collar L L After-transfer star ring TR gear L L L L Drum separation pawl unit L L L L MC unit L L L L Includes the screen grid, the charging plate, and the MC cleaner. : Charging plate cleaning by the MC cleaner Paper guide Developing Developer L L L L L L L L Supplied when installing section DV blade L L L L DSD collar DV side seal F L L L L DV side seal R L L L L Toner cartridge Attached when installing./ 750g, user replacement for every 35K. Fusing section Upper heat roller L L L L Lower heat roller L L L L Upper separation pawl L L L L Lower separation pawl L L L L Thermistor Clean and remove paper dust. Upper heat roller gear L L L L Paper guides Gears CL roller L L L L CL roller bearing L L L L Filters Ozone filter L L L L L L L L Pick-up roller Note 1 Paper feed section Paper feed roller Note 1 Separation roller Note 1 Torque limiter Note 1 Transport section Resist roller Paper exit Transport rollers reverse section Transport paper guides Paper dust remover unit L L L L Optical reflection sensor PS roller unit section Drive section Gears (Specified position) Belts Image quality Other Sensors Cleaning is performed by air blowing. Note 1: Replacement reference: Use the counter value of each paper feed port as the replacement reference. Paper feed roller/Separation pad/Torque limiter section (Include Desk, Multi purpose): 100K or 1 years AR-M351U/M451U, AR-M355U/M455U MAINTENANCE AND DETAILS OF EACH SECTION 7 - 1
2. Scanner / DSPF
Maintenance cycle : 200K Check (Clean, replace, or adjust as necessary.) Clean Unit name Optical section Part name L Replace Adjust Lubricate Move position
DSPF
When 100K 200K 300K 400K 500K 600K 700K 800K Remark calling Mirror/Lens/Reflector/Sensors Table glass/Dust-proof glass/OC White reference glass Rails Drive belt/Drive wire/Pulley Paper feed Pick-up roller Note 2 section Paper feed roller Note 2 Separation mylar lower Note 2 Separation pad Note 2 Transport section PS roller Exposure section (Dust-proof glass) Paper exit Paper exit roller section Other Sensors For cleaning, blow air.
Note 2: Replacement reference: Replace by using the SPF counter value as an indication. Paper feed section pickup roller, paper feed roller, separation pad, separation lower mylar lower: 100K or 1 year
manuals4you.com
3. Peripheral devices
Maintenance cycle : 50K Check (Clean, replace, or adjust as necessary.) Clean Option name Part name L Replace Adjust Lubricate Move position
When 100K 200K 300K 400K 500K 600K 700K 800K Remark calling Finisher Transport section Transport rollers De-curler roller ( ) Transport paper guides Drive section Gears (Specified position) Belts Other Sensors Discharge brush Staple unit Replace unit at 200K staple. Staple cartridge User replacement for every 3000 pcs. Mail-bin Transport section Transport rollers stacker Transport paper guides Drive section Gears (Specified position) Belts Other Sensors Discharge brush Saddle finisher, Transport section Transport rollers punch unit Transport paper guides Drive section Gears (Specified position) Belts Other Sensors Discharge brush Staple unit Replace unit at 300K staple. Staple cartridge User replacement for every 5000 pcs. Punch unit Replace unit at 1000K. ADU Paper feed Paper feed () () () () () () () () () Note 3 + Manual feed separation section rollers Transport section Transport rollers Transport paper guides Drive section Gears (Specified position) Belts Other Sensors Note 3: Replacement reference: Use the counter value of each paper feed port as the replacement reference. Paper feed section pickup roller, paper feed roller, separation pad: 100K or 1 year
No. 1 2 3 4 5
Name Toner cartridge Developer unit Transfer roller Process drum unit Main charger unit
Operation Supplies toner to the developing unit, and collects waste toner. Mixes toner and carrier, and attaches toner to electrostatic latent images to form visible images. Transfers toner images to the OPC drum. Forms images (electrostatic latent images, visible images) on the OPC drum. Charges the OPC drum surface negatively and evenly.
manuals4you.com
3 1 4
-650V (-620V)
12
11 10 2
30
-800V
5
25A (45ppm) 19A (31/35ppm) MAX 5KV
15
16
Paper dust cleaner
200M 200M
7 8
Toner density sensor
14
14
-500V (-470)
Temperature/humidity sensor
DM
PSPS
4 5 7 6
3 2
2 1
CN5 B8B-PH-K-S GND2 +5VCRU CRUCLK CRUSDA PSPS\ +24V1 (NC) +24V1
SRA-21T-4L
RD
MHV THV GB
SRA-21T-3
WH
SRA-21T-4L
WH
HV
SRA-21T-3
RD
BIAS
1-84432-4(AMP) DSW-F 1 GND2 2 3 GND2 4 DHVREM 5 MHVREM\ THV+PWM\ 6 GBPWM\ 7 DHVPWM\ 8 THV-PWM\ 9 10 DVREM\ DVPWM\ 11 THVREM\ 12 MHV-T 13 THin 14
CN15 9604S-14F 1 DSW-F 2 GND2 3 GND2 4 DHVREM 5 MHVREM\ 6 THV+PWM\ 7 GBPWM\ 8 DHVPWM\ 9 THV-PWM\ 10 DVREM\ 11 DVPWM\ 12 THVREM\ 13 MHV-T 14 THin
1 2 3 4 5 6 7 8
PCU PWB
CN6 9604S-08C DSW-F DSW-F GND2 GND2 DM\ DM-T DMCLK\ (NC)
1 2 3 4 5 6 7 8
Function/Operation
Type
Note
Drives the OPC drum and the transfer section. DC brushless motor Drives the OPC drum separation pawl Solenoid
Name OPC drum Drum separation pawl Sub blade (Cleaning seal) Screen grid Saw-teeth charger Separation pawl oscillation shaft Cleaning blade Waste toner transport pipe Cleaning unit
Operation Forms electrostatic latent images by laser beams. Separates paper from the drum. Prevents against toner leakage from the cleaner section. Helps to charge the OPC drum evenly with electric charges provided from the main charger. Applies a high voltage to charge the OPC drum. Moves in the front and rear frame direction to install the separation pawl. Cleans remaining toner on the OPC drum. Transports toner from the cleaner unit to the waste toner box in the toner cartridge front section. Saw teeth charger is cleaned.
manuals4you.com
C. Operational descriptions
The OPC drum surface is negatively charged by the main charger. The laser beam images are radiated to the OPC drum surface by the laser unit to form latent electrostatic images. 1) The OPC drum surface is negatively charged by the main charger.
Drum
Screen grid
OPC drum
The main charger grid is provided with the screen grid. The OPC drum is charged at a voltage virtually same as the voltage applied to the screen grid. 2) LED lights are radiated to the OPC drum surface by the laser unit to form latent electrostatic images.
Residual toner removed from the OPC drum surface is transported to the recycle toner collection section in the toner cartridge by the waste toner transport screw. 4) All the surface of the OPC drum is discharged by laser beams.
LED lights
LED lights
When LED lights are radiated to the OPC drum CGL, negative and positive charges are generated. Positive charges generated in CGL are attracted to the negative charges on the OPC drum surface. On the other hand, negative charges are attracted to the positive charges in the OPC drum aluminum layer. Therefore, positive charges and negative charges are balanced out on the OPC drum and in the aluminum layer, reducing positive and negative charges to decrease the OPC drum surface voltage. Electric charges remain at a position where LED lights are not radiated. As a result, latent electrostatic images are formed on the OPC drum surface.
6 4 2 1 8
3 7 5 2
a. Drum cartridge 1) Release the lock, and pull out the left door. 2) Open the front door.
manuals4you.com
a-1. MC unit 1) Remove the drum cartridge. 2) Check to confirm that the cleaning unit is inserted fully to the bottom. 3) Remove the pawl, and remove the MC unit.
When installing, install the DSD collar R to the drum frame, then install the drum and the DSD collar F. When installing the DSD collar, engage the DSD collar boss with the drum frame hole.
a-4. Drum separation pawl unit 1) Remove the drum cartridge. 2) Remove the screw, and remove the drum separation pawl unit. For cleaning the MC unit (charging plate), reciprocate the cleaning unit back and forth 3 times or more. When handling the separation pawl, be careful not to break or scratch the tip of the separation pawl and keep it away from dirt.
After installing the drum separation pawl unit, push the separation lever and check to confirm that the separation pawl operates normally.
a-2. Drum a-3. DSD collar 1) Remove the drum cartridge. 2) Loosen the screw, and remove the drum boss mounting plate. 3) Remove the drum, and remove the DSD collar. When removing the drum, place the drum cartridge as shown in the figure and remove the drum.
a-5. Toner reception seal 1) Remove the drum cartridge. 2) Remove the drum and the DSD collar. 3) Remove the drum separation pawl unit. 4) Remove the screw, and remove the toner reception seal.
When replacing the OPC drum, clear the following counters. Drum rotating time Drum counter When installing a new drum, apply starting powder.
(a)
When installing the toner reception seal, tighten the screw (a) on the positioning side for the first time. Check to confirm that the process earth plate and the toner reception seal are conductive. (10 or less)
a-6. Cleaner blade 1) Remove the drum cartridge. 2) Remove the drum and the DSD collar. 3) Pull it out until the cleaning unit stops. 4) Remove the screw, and remove the cleaner blade. When removing the drum blade, place the drum as shown in the figure and remove the drum blade to prevent toner from dispersing. Do not damage the cleaner blade. Do not touch the lead edge.
When attaching the side molts F/R, attach them to the attachment reference as shown. After attaching the side molt F/R, push the both ends of the blade with your fingers to check to confirm that the red moquette moves smoothly.
0.3mm
0mm Reference
Put side seal powder (1g) on the moquettes F/R and spread side seal powder all over the moquettes surfaces. Side seal powder: UKOG-0309FCZZ Do not apply powder excessively to the ambient parts. Be careful not to damage the cleaning blade and the side blade.
When installing the cleaner blade, pull the cleaner shaft fully toward you. After installing the cleaner blade, insert the cleaner shaft fully to the bottom. a-7. Side molt F a-8. Side molt R 1) Remove the drum cartridge. 2) Remove the drum and the DSD collar. 3) Remove the toner reception seal. 4) Remove the cleaner blade. 5) Remove the side molt F and R. b-1. Separation solenoid 1) Remove the screw, and remove the rear cabinet.
manuals4you.com
2) Remove the connector and the screw, and remove the PCU PWB unit.
3) Remove the screw and the connector, and remove the separation solenoid unit.
4) Remove the E-ring and the screw, and remove the separation solenoid.
DM
5 6 2 4 1 3
SRA-21T-4L
RD
PS-187 RD MHV
SRA-21T-3
WH
THV GB
PS-187 WH PS-187 YL
SRA-21T-4L
WH
HV
SRA-21T-3
RD
PS-187 BL DHV
BIAS
DV
PS-187 GR
1-84432-4(AMP) DSW-F 1 GND2 2 3 GND2 DHVREM 4 MHVREM\ 5 THV+PWM\ 6 GBPWM\ 7 8 DHVPWM\ 9 THV-PWM\ DVREM\ 10 11 DVPWM\ THVREM\ 12 MHV-T 13 THin 14
CN15 9604S-14F 1 DSW-F 2 GND2 3 GND2 4 DHVREM 5 MHVREM\ 6 THV+PWM\ 7 GBPWM\ 8 DHVPWM\ 9 THV-PWM\ 10 DVREM\ 11 DVPWM\ 12 THVREM\ 13 MHV-T 14 THin
PCU PWB
CN6 9604S-08C DSW-F DSW-F GND2 GND2 DM\ DM-T DMCLK\ (NC)
1 2 3 4 5 6 7 8
Name OPC drum motor Transfer high voltage High separation voltage
Function/Operation
Type
Note
Drives the OPC drum and the transfer section. DC brushless motor High voltage for transfer High voltage for separation of paper Function Transfers toner images from the OPC drum surface to paper. Separates paper from the drum. Transfer roller bearing Transfer roller collar Guides paper after transfer. Transfer roller drive gear
Name Transfer roller Discharge plate (Separation electrode) TR bearing (F/R) Transfer roller collar After-transfer star ring TR gear
manuals4you.com
C. Operational descriptions
1) Toner image transfer Toner images formed on the drum by the developing roller are transferred to paper by the transfer roller. Toner on the drum is negatively charged by stirring in the developing unit. By applying a positive voltage to the transfer roller, the transfer roller and paper on the transfer roller are positively charged to transfer negatively charged toner images to paper.
2) Transfer roller cleaning After completion of the job, the applied voltage to the transfer roller is switched to negative in order to attract toner from the transfer roller to the OPC drum, cleaning the drum with the cleaning blade.
Separation operation Since paper with toner images transferred on it is positively charged, a high negative voltage is applied to the separation electrode to separate the paper from the drum.
The transfer cleaning voltage and the developing positive bias are applied to the OPC drum at the timing shown below so that remaining toner on the transfer roller is attracted again to the OPC drum, performing cleaning. 1) When the power is turned on:
CLEANING WARMING UP READY CONDITION
However, the cleaning voltage is not applied during warm up after completion of SIM. 2) After completion of a print job
1sec CLEANING PRINTING Job
4 5 3 6
2 4 3
2) Remove the transfer lock pawl, and pull out the transfer roller unit.
a-1
manuals4you.com
a-2. Discharge plate 1) Remove the transfer roller unit. 2) Remove the screw, and remove the discharge plate holder and the discharge plate.
a-3. Transfer roller a-4. Transfer roller collar a-5. TR bearing (F/R) a-6. TR gear 1) Remove the transfer roller unit. 2) Remove the screw, and remove the discharge plate holder and the discharge plate.
manuals4you.com
DM
TM1
CN6 9604S-08C 1 DSW-F 2 DSW-F 3 GND2 4 GND2 5 DM\ 6 DM-T 7 DMCLK\ 8 (NC)
HUS-DV TH-DV
1 3
TCS
3
QR/P8-12S-C(01) DVCH1 1 DVCH2 2 BR DVCH3 3 BR TH-DV 4 GY GND2 5 GND2 6 BR TCS 7 GY GND2 8 RD +24V1 9 BL +5V2 10 BR HUS-DV 11 WH DVBias 12 1 2 3 4 5 6 7 8 9 10 11 WH 12 #187
CN5 B8B-PH-K-S BR 1 GND2 GY 2 +5VCRU BL 3 CRUCLK BR 4 CRUSDA 5 PSPS\ 6 +24V1 7 (NC) 8 +24V1 CN8 B11B-PH-K-S 1 DVCH1 2 DVCH2 3 DVCH3 4 TH-DV 5 GND2 6 GND2 7 TCS 8 GND2 9 +24V1 10 +5V2 11 HUS-DV
HUS-DV TH-DV
TCS
1 2 3 4
BR BR BR BR GY GY BR GY RD BL BR
Bias
SRA-21T-3 Bias
PCU PWB
Name Developing humidity sensor Developing temperature thermistor Toner density sensor Drum motor Toner motor Developing bias
Function/Operation Developing section peripheral humidity detection Temperature detection around the developing unit Toner density detection Drives the drum/developing section. Drives the toner hopper. High voltage for developing bias
Operation Forms magnetic brush with developer and put toner on the OPC drum. Keeps the height of the magnetic brush on the developing roller at a fixed level. Mixes developer (carrier and toner) and charges toner negatively.
manuals4you.com
C. Operational descriptions
Electrostatic latent images formed on the OPC drum by the LED (writing) unit (LED image light) are converted into visible images by toner.
CGL CTL
-500V (-470V)
Toner in the developing unit is stirred by the mixing roller. When toner is stirred, it is negatively charged by mechanical friction. The developing bias voltage (negative) is applied to the developing roller. Negatively charged toner is attracted and attached to the area on the OPC drum where negative voltage is reduced by exposure. On the other hand, the negative voltage at an area where exposure is not made is higher than the developing bias voltage, and toner is not attached.
4 2 1
a. DV cartridge 1) Release the lock, and pull out the left door. 2) Open the front door.
b-1
manuals4you.com
a-1. Developer 1) Remove the DV cartridge. 2) Remove the screw, and remove the DV cover.
When attaching the DV blade, attach to the attachment reference shown in the figure below.
0mm
Reference (Step)
0.5mm 0mm
0.5mm
Reference
a-3. DV side seal F a-4. DV side seal R 1) Remove the DV cartridge. 2) Remove the DV side seal F and the DV side seal R. 3) Remove old developer.
Use a metal scale or a minus screwdriver for easy operation. 4) Supply new developer. When attaching the SV side seals F and R, attach them to the attachment reference shown in the figure below.
0.5mm
Reference
0.5mm
Reference
0mm 0mm
Reference
a-5. Toner density sensor a-6. Humidity sensor 1) Remove the DV cartridge. 2) Remove the bottom cover.
a-8. Toner motor 1) Remove the toner cartridge. 2) Remove the screw, and remove the rear cabinet.
3) Remove the bottom cover. 4) Remove the screw and the connector, and remove the humidity sensor. 2) Remove the connector and the screw, and remove the PCU PWB unit.
a-7. Toner cartridge 1) Open the left door and the front door. 2) Release the lock and remove the toner cartridge. 3) Remove the connector and the screw, and remove the toner motor unit.
4) Remove the coupling and the spring from the toner motor.
manuals4you.com
2. Fusing section
A. General
This section fused toner (which is transferred onto paper in the transfer section) onto paper by heat and pressure of the fusing roller.
Copy Paper exit
Fusing roller (Heating)
Fusing
Cleaning roller
Main motor
SMP-04V-NC+SMR-04V-N
BR GY BR GY 1 2 3 4
BR 1 2 3 4 GY BR GY
WH 1 2 3 4 1 2 3 4 WH BK GY
VLP-03V+VLR-03V
1 2 3
CN14 B16B-PH-K-S
BR RD 1 2 3 4 5 6 7 8 9 10 11
HL1 HL2 L2
1 2 3
FW +24VPR HLPR +12V2 HLCNT1 HLCNT2 RTH1 GND2 RTH2 GND2 (NC) (NC) MSW MON BUP_PR GND GND
SRA-51T-4
SRA-51T-4
1 2
HL1 HL2 L2
FILTER PWB
L2out CN1 (NC) B03P-VL(RD) L2in
3 2 1 BK BK WH WH BK
VLP-03V+VLR-03V
1 2 3
HL1 HL2 L2
BK BR WH WH WH BK BK
1 2 3
12 BR 13 14 15 16
TAIWAN ONLY
GY
REACTOR PWB
HL-1N CN2 B03P-VL HL-2N HL-L L2 (NC) CN1 B2P4-VH (NC) L2R
1 2 3 1 2 3 4
CN17 B9P-VH
RD 1 RD 2 GY 3 4 5 OR 6 OR 7 GY 8 GY 9
BK
200V ONLY
CN9 9604S-08C 1 2 3 4 5 6 7 8 DSW-F DSW-F GND2 GND2 +5V2 GND2 MM\ MM-T
MM
7 9
Rth1
6 8
Rth2 HLTS HL2 HL1
5 2
7,8
10
Name Fusing temperature sensor (1) Fusing temperature sensor (2) Thermostat (1)
Type
Function/Operation
HL1 HL2 MM
HL1 HL2 MM
Thermistor Detects the surface temperature of the fusing roller (heating). (Center section) Thermistor Detects the surface temperature of the fusing roller (heating). (Edge section) Shuts conduction to the heater lamp when the temperature rises abnormally. [For the fusing roller (heating)] Heats the fusing roller (heating). Heats the fusing roller (heating). Drives the fusing unit.
Note
1 2 3 4
Heater lamp 1 Heater lamp 2 Upper heat roller Lower heat roller
5 6 7 8 9
Fusing upper separation pawl Fusing lower separation pawl Thermistor (Center) Thermistor (Side) Thermostat
10
Cleaning roller
Generates heat and transmits heat to the heat roller. The temperature is controlled by the thermistor. (Temperature control is made mainly on the center.) Generates heat and transmits heat to the heat roller. The temperature is controlled by the thermistor. (Temperature control is made mainly on both sides.) Transmits heat to melt toner on paper and fuse toner by means of a pressure with the lower heat roller. Fuses toner on paper by means of a pressure with the upper heat roller. To improve fusing capability, the diameter is greater than the conventional ones. (30mm40mm) Prevents winding of paper around the upper heat roller. Prevents winding of paper around the lower heat roller. Detects the surface temperature of the upper heat roller. (On/off of heater lamp 1 is controlled according to the detected temperature.) Detects the surface temperature of the upper heat roller. (On/off of heater lamp 2 is controlled according to the detected temperature.) When an abnormal temperature of the upper heat roller is detected, the heater lamp power is interrupted. To supply power again, press the switch on the top. Cleans toner on the lower heat roller. The blast process is employed.
C. Operational descriptions
(1) Fusing unit drive
To drive the fusing unit, the drive power is transmitted from the drive motor (MM) through the connection gear to the upper heat roller gear. The drive motor DC brushless motor is driven according to the control signal sent from the PCU.
PCU
(2) Heater lamp drive
MM
The surface temperature of the heat roller detected by the thermistor is sent to the PCU. When the temperature is lower than the specified level, the heater lamp lighting signal is sent from the PCU to the heater lamp drive circuit in the sub power PWB. The power triac in the heater lamp drive circuit is turned on, and the AC power is supplied to the heater lamp, lighting the lamp and heating the heat roller. To prepare for an abnormally high temperature of the heat roller, the thermostat is provided for safety. When the thermostat is opened, power supply (AC line) to the heater lamp is cut off.
Fusing roller (Heating) HL2 HL1
Paper exit
manuals4you.com
The fusing heat roller (heating) is provided with two heater lamps, which heat the fusing roller to fuse toner onto paper. The fusing rollers (pressing) are of silicon rubber because of the following reasons and purpose. 1) Paper is separated upward. (Since the fusing roller (heating) is of higher hardness, the fusing roller (pressing) is deformed to separate paper upward.) 2) The nip quantity is increased to increase heat capacity for paper. 3) By pressing paper with the flexible roller, toner is fused without deformation.
Pre-heat
3 6
2 8 7
1 4
8 5
a-2
a-1
1) Remove the fusing unit. 2) Open the fusing rear lower PG, and remove the lower separation pawl.
a-2. Upper separation pawl 1) Remove the fusing unit. 2) Remove the rear upper PG, and remove the upper separation pawl. 2) Remove the stopper R.
manuals4you.com
a-3. Thermistor 1) Remove the fusing unit. 2) Remove the screw, and remove the fusing drawer. Remove the connector. 3) Remove the screw, and remove the thermistor.
a-5. CL roller a-6. CL roller bearing 1) Remove the fusing unit. 2) Remove the lower heat roller. 3) Remove the CL roller, and remove the CL roller bearing.
a-7. Heater lamp 1) Remove the fusing unit. a-4. Lower heat roller 1) Remove the fusing unit. 2) Release pressure with the pressure adjustment lever. 3) Remove the screw, and open the fusing unit. 2) Open the fusing unit. 3) Remove the screw, and remove the heater lamp. Be careful not to mistake the installing position of the heater lamp.
4) Open the fusing rear lower PG. 5) Remove the lower heat roller, and remove the lower heat roller bearing.
When installing, loosen the screws on the front side (drawer ON side) then the screws on the rear side (gear side) in this sequence. Check to confirm again that the screws are tighten securely. (If any screw is loosened, a bad contact may cause heating.)
a-8. Upper heat roller a-9. Upper heat roller gear 1) Remove the fusing unit. 2) Open the fusing unit. 3) Remove the fusing rear upper PG. 4) Remove the heater lamp. 5) Remove the upper heat roller, the roller stopper. The upper heat roller gear, and the upper heat roller bearing.
A. General
This section picks up paper in the cassette and feed it to the transport roller section. The capacity of the paper feed tray is 550 sheets for 64g/m2 or 500 sheets for 80g/m2. a-10. Thermostat 1) Remove the fusing unit. 2) Open the fusing unit. 3) Remove the fusing rear upper PG. 4) Remove the heater lamp. 5) Remove the upper heat roller. 6) Remove the screw, and remove the electrode plate and the thermostat. There are three kinds of the paper feed desk: 3-stage paper feed desk (AR-D27), 2-stage paper feed desk (AR-D28), and 1-stage paper fed desk (AR-MU2). For details, refer to the AR-D27/D28/ MU2 Service Manual.
When installing, check to confirm that the screws are securely tighten again. (If any screw is loosened, a bad contact may cause heating.)
manuals4you.com
BR 1 GY 2 BR 3 BR 4
LUM
MM
2 3 1
PHNR-02-H+BU02P-TR-P-H BR 2 CPFC\ 1 RD 1 +24V1 2
PCU PWB
8FE-ST-VK-N DSW-L DSW-L GND1 GND1 +5V2 GND2 MM\ MM-T CN9 9604S-08C 1 DSW-F 2 DSW-F 3 GND2 4 GND2 5 +5V2 6 GND2 7 MM\ 8 MM-T
8 7 6 5 4 3 2 1
CN13 B24B-PHDSS-B GND2 1 +24V1 2 PED 3 CPFC\ 4 +5V2 5 +24V1 6 GND2 7 RRC\ 8 LUD 9 +24V1 10 +5V2 11 TRC\ 12 GND 13 CSS 14 GND2 15 GND2 16 PPD1 17 LUMB 18 +5V2 19 LUMA 20 CFM1\ 21 GND2 22 +24V1 23 GND2 24
PHNR-09-H+BU09P-TR-P-H GY RD BR BR BL GY BR BL 1 2 3 4 5 6 7 8 9 +5V2 PPD1 GND2 +5V2 LUD GND2 +5V2 PED GND2 9 8 7 6 5 4 3 2 1
BL BR GY BL BR GY
BL BR GY BL BR GY
BR GY BR BR
Function/Operation
Note
Paper freed tray section roller ON/ OFF control Paper feed tray lift-up motor Drives the lift plate of the paper feed tray. Defector Paper empty detection Defector Paper tray upper limit detection
1 2 3 4 5 6
Name Take-up roller Paper feed roller Separation roller Paper upper limit sensor Paper sensor Lift-up motor
Function Picks up paper and transports it to the paper feed roller. Feed paper in the machine. Rotates simultaneously with the paper feed roller to prevent against overlapped feed. For the manual feed tray, the separation pad is used instead of the roller. Detects the top surface of paper and stops paper at the feed position. Detects paper presence. (Paper empty, upper limit detection: ON / Paper presence detection: OFF) Lifts the paper feed base up to the paper feed position (upper limit detection position).
Remark
C. Operational descriptions
[Paper feed operation] (1) Preliminary operation except for the manual feed tray
1) Load paper and insert the tray, and the tray sensor will be turned on. 2) The lift-up motor rotates. 3) The upper limit sensor turns on.
(2) Paper length sensor (MPT/2nd and 3rd steps of 3-step paper feed desk)
Length detection is performed by combination of cassette size sensors 1 - 4.
CSS1
CSS2
CSS4 CSS3
Paper length and paper size Vertical size detection pattern 1 2 CSS1 ON OFF Detection SW status CSS2 CSS3 ON OFF ON OFF CSS4 ON ON AB series size B5 A4 Inch series size EXTRA LT Detection width range 147.0 - 198.0 198.0 - 237.0 Same range size Postcard Monarch DBL P/C C5 DL COM-10 ISO-B5
3 4 5 6 7 0
ON ON ON ON ON OFF
B5R
EX-R
237.0 - 274.0 274.0 - 314.0 314.0 - 347.0 347.0 - 389.0 389.0 - 432.8
manuals4you.com
For the other than above, the paper size is considered as "Extra." 3) 2nd and 3rd steps of 3-step paper feed tray Paper detection is performed by the detector in linkage with the rear edge plate.
CSS1
CSS2
CSS4 CSS3
Paper size for automatic detection Vertical size detection pattern 1 2 3 4 5 6 7 0 CSS1 ON OFF OFF OFF ON ON ON OFF Detection SW status CSS2 CSS3 ON OFF ON OFF ON ON OFF ON OFF ON OFF ON ON ON OFF OFF CSS4 ON ON ON ON ON OFF OFF OFF AB series size Inch series size Detection width range 147.0 - 198.0 198.0 - 237.0 237.0 - 274.0 274.0 - 314.0 314.0 - 347.0 347.0 - 389.0 389.0 - 432.8
B5 EXTRA A4 LT B5R EX-R A4R LTR Foolscap EXTRA B4 LGL A3 WLT Tray not installed
(Remaining quantity sensor status change when the tray is moving up and remaining quantity) Paper empty is detected by the paper empty sensor. When paper empty is detected MCPED (Paper empty sensor) Rotating plate Paper remaining quantity detection actuator 1/3 area sensor logic LOW MCSPD (Paper remaining quantity sensor)
manuals4you.com
D.
Note 1: Replacement reference: Use the counter value of each paper feed port as the replacement reference. Paper feed roller/Separation pad/Torque limiter section (Include Desk, Multi purpose): 100K or 1 years
2 4 1 3
a-1. Pick-up roller a-2. Paper feed roller a-3. Separation roller a-4. Torque limiter 1) Pull out No. 1 paper feed tray unit.
3) Disengage the pawl, and remove the pickup roller and the paper feed roller.
a-7. Cassette detection PWB 1) Remove the screw, and remove the rear cabinet.
4) Disengage the pawl, and remove the separation roller and the torque limiter. 2) Remove the connector, and remove the cassette detection PWB.
a-5. Paper feed cassette upper limit detection a-6. Paper feed cassette paper empty detection 1) Pull out No. 1 paper feed tray unit, and remove the paper guide. 2) Remove the screw, and remove the pickup roller arm. 3) Remove the paper feed roller and each part. 4) Remove the pickup roller shaft, and remove the pickup roller guide. 5) Remove the actuator. 6) Remove the connector, the paper feed cassette upper limit detection, and the paper feed cassette paper empty detection.
a-8. Lift-up motor 1) Remove the screw, and remove the rear cabinet.
2) Remove the connector and the screw, and remove the lift-up motor unit.
manuals4you.com
3) Remove the E-ring, the gear, and the spring. 4) Remove the screw, and remove the lift-up motor.
A. General
In this paper transport section, paper fed from each paper feed port is transported to the resist roller section, where the lead edge of the paper is aligned with the lead edge of images on the OPC drum. Images are transferred onto paper in the transfer section, and the paper is discharged face-up or face-down through the fusing section.
u an
yo 4 ls
o u.c
CN4 B32B-PHDSS-B /POMXB 1 +5V2 2 /POMB 3 POD1 4 /POMA 5 GND2 6 /POMXA 7 +5V2 8 +24V1 9 POD2 10 +24V1 11 GND2 12 GND2 13 +5V2 14 CFM2\ 15 POD3 16 +24V1 17 GND2 18 +24V1 19 CFM2\ 20 +24V1 21 VFM2\ 22 +24V1 23 GND2 24 (NC) 25 GND2 26 DSW-L 27 DSW-L 28 (NC) 29 (NC) 30 (NC) 31 DSW-F 32
BR BL BR BR BR GY BR BL RD BR RD GY BL BR GY
MM
RD RD GY
RRC
4
RD
TRC
GY 8FE-ST-VK-N 8 DSW-L 7 DSW-L 6 GND1 5 GND1 4 +5V2 3 GND2 2 MM\ 1 MM-T PHNR-02-H+BU02P-TR-P-H BR 1 RRC\ 2 RD 2 +24V1 1 PHNR-03-H+BU03P-TR-P-H BR 1 TRC1\ 3 2 (NC) 2 RD 3 +24V1 1 PHNR-09-H+BU09P-TR-P-H PHNR-03-H+BU03P-TR-P-H BL BL BL 3 1 +5V2 1 +5V2 9 BR BR BR 2 PPD1 8 2 PPD1 2 GY GY GY 3 GND2 7 3 GND2 1 4 +5V2 6 5 LUD 5 6 GND2 4 7 +5V2 3 8 PED 2 9 GND2 1 179228-3(AMP) 1 +5V2 2 PPD1 3 GND2
PCU PWB
CN9 9604S-08C DSW-F 1 DSW-F 2 GND2 3 GND2 4 +5V1 5 GND2 6 MM\ 7 MM-T 8 CN13 B24B-PHDSS-B GND2 1 +24V1 2 PED 3 CPFC\ 4 +5V2 5 +24V1 6 GND2 7 RRC\ 8 LUD 9 +24V1 10 +5V2 11 TRC\ 12 GND 13 CSS 14 GND2 15 GND2 16 PPD1 17 LUMB 18 +5V2 19 LUMA 20 CFM1\ 21 GND2 22 +24V1 23 GND2 24
RD BR RD BR
3
GY
GY BR BL BR GY RD GY
2 1
Name Paper exit detector 1 Paper exit detector 2 Paper exit detector 3 Paper exit motor Fusing cooling fan motor Fusing cooling fan motor
Function/Operation Paper exit detection from fusing Paper pass detection from paper exit Paper exit detection to upper section paper exit tray (Full detection) Drives the paper exit roller. Discharges heat generated in the fusing section. Discharges heat generated in the fusing section to cool it.
Type Transmission type Transmission type Transmission type Stepping motor DC brushless motor DC brushless motor
Note Paper transport system sensor Paper transport system sensor Paper transport system sensor Selection of Normal speed/ High speed/ Reverse rotation PWM control PWM control
manuals4you.com
Name Resist roller clutch Paper transport roller clutch Main motor
Function/Operation Resist roller ON/OFF control Paper transport roller ON/OFF control Drives the paper transport and resist roller
Type
Note
No. 1 2 4 5
Name Transport roller 15 Resist roller (Drive) Paper exit and transport roller Paper exit roller
Function Transports paper to the transport resist roller. Transports paper to the transfer section. / Controls the transport timing of paper to adjust the relationship between images and paper. Transports paper from the fusing roller to the paper exit roller. Discharges paper to the paper exit tray. / Switchbacks paper.
C. Operational descriptions
[Paper transport path and paper exit] Paper transport path with an option installed 1.
2.
Option Desk Duplex unit Finisher Male bin stacker Punch unit
3.
4) Paper is taken into the machine again, passed over the reverse gate, and transported to the duplex unit. 5) When duplex printing is made, the ADU gate solenoid switches to the upper side of the ADU paper exit gate to switch the paper path to the ADU.
6) When paper is discharged to the left tray or when paper is transported to the console finisher (AR-FN7), the ADU gate solenoid switches to the upper side of the ADU paper exit gate to switch the paper path to the ADU.
4.
The AR-FN6 is provided with the decurler to improve alignment capability of finishing. The decurler makes decurling against curling of paper by means of the difference in rigidity of the upper roller (metal) and the lower roller (sponge).
Metal
Sponge
manuals4you.com
2 2 4
1 2 5
a-1
d-6 d-5 d-2 d-3 d-1 d-4 d-8 d d-7 b-4 c-2 c-1 c-3 b b-1 b-2 b-3 c
b-1. Resist roller 1) Remove the paper dust cleaner unit. 2) Remove the resist roller unit. 3) Remove the parts, and remove the resist roller. 4) Remove the gear, the parallel pin, and the E-ring.
b-2. Paper transport roller 1) Remove the paper dust cleaner unit. 2) Remove the resist roller unit. 3) Remove the parts, and remove the paper transport roller.
b. Resist roller unit 1) Remove the paper dust cleaner unit. 2) Remove the screw, and remove the resist roller unit. Disconnect the connector.
b-3. Paper transport detection b-4. High voltage resistor PWB 1) Remove the paper dust cleaner unit. 2) Remove the resist roller unit. 3) Remove the screw, and remove the paper dust cleaner guide.
manuals4you.com
4) Remove the screw and the connector, and remove the paper transport detector. 5) Remove the screw and the earth wire, and remove the high voltage resistor PWB.
3) Remove the connector, the screw, and the washer, and remove the suction fan motor. 4) Remove the screw, and remove the high voltage resistor PWB.
c. Left door unit 1) Remove the screw, and remove the left door unit.
When installing the fan, check the left door indication arrow and note the fan direction. c-3. Drawer PWB 1) Remove the left door unit. 2) Remove the left door transport paper guide. 3) Remove the screw, and the reverse gate unit and remove the angle.
c-1. Suction fan motor c-2. High voltage resistor PWB 1) Remove the left door unit. 2) Remove the screw, and remove the transfer lock pawl. 3) Remove the screw, and remove the left door transport paper guide. 4) Remove the screw, and remove the angle. 5) Remove the connector, the screw, and remove the drawer PWB.
6) Remove the screw, and remove the paper exit tray cabinet. 7) Remove the screw, and remove the front right upper cabinet. 8) Remove the front door.
2) Remove the screw, and remove the rear cabinet. 9) Remove the E-ring and the parts. 10) Remove the screw and the connector, and remove the paper exit reverse unit.
3) Remove the screw, and remove the paper exit upper cabinet. 4) Remove the screw, and remove the left rear cabinet. 5) Remove the screw, and remove the front left upper cabinet.
d-1. Paper exit detection 1 1) Remove the paper exit reverse unit. 2) Remove the actuator. Remove the connector, and remove the paper exit detection 1.
manuals4you.com
d-2. Paper exit motor 1) Remove the paper exit reverse unit. 2) Remove the connector and the screw, and remove the paper exit motor.
4) Remove the connector, the exhaust heat fan, the paper exit detection 2, the paper exit full detection.
d-3. Left door open/close detection 1) Remove the paper exit reverse unit. 2) Remove the connector and the screw, and remove the left door open/close detection.
When installing the fan, check the indication arrow and note the fan direction. d-7. After-fusing roller 1) Remove the paper exit reverse unit. 2) Remove the E-ring and the parts. 3) Remove the connector and the screw, and remove the paper exit drive frame.
d-4. Exhaust heat fan motor d-5. Paper exit detection 2 d-6. Paper exit full detection 1) Remove the paper exit reverse unit. 2) Remove the screw, and remove the exhaust duct. 3) Remove the screw, and remove the paper exit upper paper guide reinforcement plate. 4) Remove the bearing, the E-ring, and the parts. 5) Remove the E-ring, and remove the fusing rear roller. Remove the bearing.
d-8. Paper exit roller 1) Remove the paper exit reverse unit. 2) Remove the screw, and remove the paper exit upper paper guide unit.
3) Remove the E-ring, and remove the paper exit roller. Remove the bearing, the gear, and the parallel pin.
manuals4you.com
A. General
Image data sent from the MFP (image process circuit) through the mother board and PCU are converted into laser beams to radiate onto the drum surface.
5 2 10 6
BD
PM
3 4 7
CN2 S32B-PHDSS-B 45 sheets (35 sheets) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 TEST3 TEST2 GND2 /SYNC GND2 GND2 GND2 LSU_S/H VRB GND2 GND2 TEST VIDEO /VIDEO /LDON GND2 GND2 +5V2 GND2 +5V2 +24V1 +24V1 /VFM1 GND2 /START /VFM1 /PMCLK /READY GND2 GND2 +5V LD GND2 CN1 S11B-PH-K-S 45 sheets (35 sheets) +24V1 11 VFM1\ 10 GND2 9 +24V1 8 VFM1\ 7 GND2 6 +24V1 5 PMCLK\ 4 READY(READY\) 3 START\ 2 GND2 1
9
PHNR-03-H+BU03P-TR-P-H RD BR GY RD BR GY RD BR BR BR GY 3 +24V1 2 VFM1\ 1 GND2 RD 1 BR 2 GY 3
VFM1
POWER SOURCE SECTION
CN1
CN2
VFM1
LSU
CN3 S4B-PH-K-S GND2 SYNC\ GND2 +5V2 BR 1 LB 2 BR 3 BL 4 B4B-PH-K-S 4 GND2 3 SYNC\ 2 GND2 1 +5V2
Code PM BD No. RW RW RW RW RW RW
Signal name PM
Name Polygon mirror (motor) BD PWB Code, signal name +5VLD /READY /PMCLK /START /VIDEO /SYNC
Type
Function/Operation Reflects laser beams at the constant rotation speed. Detects the laser scan start timing. This device is used to detect a laser trouble.
NOTE
Name Control signal Control signal Control signal Control signal Control signal Control signal
Function 5V power for laser diode Polygon mirror motor READY signal ("L" in the constant speed rotation) Clock signal for driving the polygon mirror motor Polygon mirror motor drive start signal VIDEO (Image signal) Sync signal (SYNC) from BD, sync signal for 1 line
No. 1 2 3 4 5 6 7 8 9 10
Name Laser control PWB Cylindrical lens Incidence reflection mirror No. 1 mirror f lens 1 f lens 2 BD PWB No. 2 mirror Plane lens Convergence lens for BD
Function Controls laser beam flashing and the output value. Converges laser beams to focus. Assures the optical path for laser beams. Assures the optical path for laser beams. Deflects laser beams so that the laser scan speeds on the both ends of the drum and that at the center of the drum are the same. Detects the timing of laser scan start. This device is used to detect a laser trouble. Converges laser beams to focus. Assures the optical path for laser beams. Converges laser beams onto the BD PWB. a-1. LSU 1) Remove the screw, and remove the right cabinet.
C. Operational descriptions
[Laser optical path]
The LSU must not be disassembled in the market.
a-1
manuals4you.com
8) Remove the screw, and remove the main switch mounting plate.
9) Remove the power unit. 5) Remove the connector, the screw, and the angle. Remove the snap band. Do not disconnect the LSU side.
10) Remove the connector and the screw, and remove the duct holding cover.
6) Pull out the No. 1 paper feed tray unit, and push up and remove the front door.
7) Release the lock, and pull out the left door. Remove the screw, and remove the front cover right.
6. Scanner section
A. General
There are following three methods of scanning documents in this machine. a. Place a document on the table glass. The copy lamp unit is operated to radiate copy lamp light onto the document, scanning the document with the CCD. b. The SPF feeds a document. The copy lamp light is radiated onto the document which is stopped at the specified position and the document is scanned by the CCD. c. The SPF feed a document. The LED light of the CIS unit which is attached to the SPF is radiated to the back of the document, and the document is scanned by the CIS.
manuals4you.com
10
CN1 IL-FPR-40S-VF-E1500 40 GND2 39 GND2 38 GND2 37 GND2 36 1_DATA1+ 35 1_DATA134 GND2 33 1_DATA0+ 32 1_DATA031 GND2 30 1_CLK+ 29 1_CLK28 GND2 27 /1_DBL+ 26 /1_DBL25 GND2 24 FRM_CCD1 23 PAGE1 22 CLK_CCD1 21 ADD_CCD1 20 TXD_CCD1 19 RXD_CCD1 18 RES_CCD1 17 GND2 16 +3.3V3 15 +3.3V3 14 GND2 13 +5VCCD 12 +5VCCD 11 +5VCCD 10 +5VCCD 9 +5VCCD 8 +5VCCD 7 +5VCCD 6 +5VCCD 5 GND2 4 +10VCCD 3 +10VCCD 2 GND2 1 GND2
CN1 SLD5R-1 GND2 5 GND2 4 /CL1 3 +24V3 2 +24V3 1 CN2 SLD5S-1 GND2 GND2 /CL1 +24V3 +24V3
CN3 TX25-100P-LT-H1
CN1 TX24-100R-LT-H1
1 2 3 4 5
10
4 12
11
Signal name Name MIM Scanner (reading) motor MHPS Scanner home position sensor detector CL1 CL1 Copy lamp CCD PWB CCD PWB
Function/Operation Drives the scanner (reading) section. Scanner home position detection Document exposure lamp Front document image scan (Document table/ SPF mode) Converts the document images (optical signals) into electrical signals.
Note Sensor
No. 1 2 3 4 5 6 7 8 9
Name Copy lamp unit Reflector No. 1 mirror No. 2 mirror No. 3 mirror CCD/Lens unit White balance sheet Table glass SPF scan glass
10 11 12
Mirror home position sensor (MHPS) Scan motor DSPF white balance sheet
Function Lights up to radiate documents. A xenon lamp (operating on 3.15KV) is employed. This mirror converges lights on documents. Secures the optical path between a document and No. 2 mirror. Secures the optical path between No. 1 mirror and No. 3 mirror. Secures the optical path between No. 2 mirror and the CCD. The reduction optical type CCD (Charge Coupled Device) of 7,450 pixels is employed. The scan resolution is 600dpi. Converts photo energy reflected by the mirrors into electric energy. Serves as the reference sheet of white for scanning with the CCD/Lens unit. If dust or dirt is attached to this sheet, white streaks may be produced. A document is set on this glass. The glass surface is coated for protection against static electricity. A document is set to the top left corner. The copy lamp unit is fixed, and a document is moved over this glass to scan line by line. The glass surface is coated for protection against static electricity. If dust or dirt is attached to this sheet, black streaks may be produced. Detects the home position of the mirror base unit. Drives the mirror base and the copy lamp unit. Serves as the reference sheet of white for scanning with the CIS unit. If dust or dirt is attached to this sheet, white streaks may be produced.
C. Operational descriptions
(1) CCD/lens unit
This machine employs the reduction optical-type line CCD (Charge Coupled Device) of scan resolution of 600dpi and 7450 pixels. CCD scan is performed by shifting the scan positions sequentially by the carriage unit (lamp and mirror) scan or moving the document with the SPF. Lights reflected by the document are reflected by each mirror to form images on CCD elements through the reduction-type lens. The CCD converts the optical energy into electrical energy (analog). (Photoelectric conversion)
CIS
CIS UNI
Focus point
manuals4you.com
SPFM
1030mS
manuals4you.com
5 2 4 5 1 1 3
a-1
Lamp unit
a-10 a-11 a-13 a-12 a-14
manuals4you.com
2) 1) 3) 4) 3) 1)
a-7. Drive wire a-2. Dust-proof glass a-3. Table glass a-4. White reference glass 1) Remove the table glass holder and the white reference glass holder, and remove the table glass and the white reference glass. a-8. Pulley a-9. Drive belt 1) Remove the table glass. 2) Check the drive wire, pulley and drive belt.
4) 4) 6) 5) 3) 1) 1) 2)
a-10. Scan motor 1) Remove the scanner rear cabinet and the rear lower cabinet.
3) 4) 3) 1)
1)
2)
2) Pull out the harness from the scanner control PWB. 3) Remove the scan motor.
a-14. Scanner interface PWB 1) Remove the table glass. 2) Remove the PWB cover and the harness cover.
3) 2) 1)
a-11. OC open sensor 1) Remove the rear cabinet. 2) Remove the OC open sensor. 3) Remove the scanner interface PWB.
2)
1) 3)
a-12. Mirror home position sensor 1) Remove the rear cabinet. 2) Remove the mirror home position sensor.
b. Lamp unit 1) Remove the table glass. 2) Remove the scan lamp unit.
4) 1)
3)
2) 3) 1)
1)
a-13. Scanner control PWB 1) Remove the scanner rear lower cabinet. 2) Disconnect the connector and earth band, and pull out the scanner control PWB.
2) 2)
5) 2) 2) 1) 1) 4) 3)
When the scanner control PWB is replaced, the EEPROM must be replaced.
manuals4you.com
b-1. Reflector b-1. Mirror 1) Remove the table glass. 2) Clean the reflector and the mirror.
b-4. Inverter PWB 1) Remove the table glass. 2) Hold with your hand and remove the screw. Remove the connector and remove the inverter PWB.
b-3. Lamp 1) Remove the table glass. 2) Slide the lamp unit base to the notch section. c. CCD lens PWB unit 1) Remove the table glass. 2) Remove the dark-box cover.
1) 1) 2) 1) 1)
1)
3) Flip the notch section Mylar and remove the screw. Slide the lamp holder to the front side, and remove it upward from the rear side. Remove the connector.
3) Remove the CCD lens PWB unit. Note: The CCD lens PWB unit is factory-adjusted before shipping. Since these adjustments cannot be performed in the market. Never touch the screws other than screw 2) of the CCD lens PWB unit.
1) 2)
3)
4) Clean the CCD lens and the CCD. Note for CCD lens PWB unit installation <1> Adjust the CCD unit adjustment value listed in the table below with the scribed line on the lens base.
CCD unit adjustment value (+) direction Reference line (-) direction 1 scale: 1.4mm
7. DSPF section
CCD adjustment value 5.0~ 3.6~4.9 2.2~3.5 0.8~2.1 -0.6~0.7 -2.0~ -0.7 -3.4~ -2.1 -4.8~ -3.5 ~ -4.9
<2> Make a sample copy at the above position, and measure the magnification ratio. <3> Change the installing position in the horizontal direction to adjust the magnification ratio. When the copy image is longer than the original, shift to the positive (+) direction. When the copy image is shorter than the original, shift to the negative (-) direction. 1 scale of the scribed line corresponds to 0.3% of magnification ratio. If this adjustment is not satisfactory, make a fine adjustment with SIM 48-1. (Refer to the adjustment described below.) c-1. CCD lens 1) Remove the table glass. 2) Remove the dark-box cover. 3) Remove the lens cover.
A. General
Sheet documents are automatically fed and transported for continuous scanning. The DSPF (AR-EF3) supports duplex sheet to scan both of the front and the back surfaces at a time.
manuals4you.com
8 10 5 2
STMP
CN1 TX24-100R-LT-H1
CN3 TX25-100P-LT-H1
PHNR-6-H+BU6P-TR-P-H 6 5 4 3 2 1 1754873+179228-3 +5V1 SPED GND2 1754873+179228-3 +5V2 SCOV GND2 1754873+179228-3 +5V2 SPPD GND2 1 2 3 1 2 3 PHNR-11-H+BU11P-TR-P-H 1 2 3 4 5 6 7 8 9 10 11 +5V1 SPED GND2 +5V2 SCOV GND2 +5V2 SPPD GND2 +24V3 /SDSS 11 10 9 8 7 6 5 4 3 2 1 1 2 3 /B +24V3 B A +24V3 /A 1 2 3 4 5 6
CNC B26B-PHDSS-B +24V3 +24V3 GND2 GND2 +5V2 GND2 VAREF SPPD SPFC SPED SDSS SCOV SRRC SPWS SPFS 7 8 5 6 4 9 17 19 18 21 12 23 14 24 16
CN10 S28B-PHDSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 +24V3 +24V3 GND2 GND2 +5V1 +5V2 GND2 VAREF SPPD SPFC SPED SDSS SCOV SRRC SPWS SPFS GND2 GND2 SPFMO0 SPOD /SPFMA SOCD SPFMA SPLS1 /SPFMB SPLS2 SPFMB SPFSET CN7 S26B-PHDSS 2_DATA12_DATA1+ 2_DATA02_DATA0+ 2_CLK2_CLK+ 2_DBL2_DBL+ GND2 FRM_CCD2 CLK_CCD2 PAGE2 ADD_CCD2 TXD_CCD2 RES_CCD2 RXD_CCD2 +3.3V +3.3V +24V3 GND2 +12V1 GND2 +5V2 GND2 +5V2 /CIS_SET VLED DGND VAS DGND VDS DGND SCN DGND LGATE DGND CLK DGND DATA DGND
LD
CNB B22B-PHDSS-B 5 +5V 16 1 7 18 2 8 14 3 11 15 9 4 20 10 22 6 12 19 13 17 21 SPED GND2 +5V2 SCOV GND2 +5V2 SPPD GND2 +24V3 /SDSS +5VPOD GND2 SPOD +5V2 SOCD GND2 +24V3 /SPFC +24V3 /SRRC (NC)
SPFMO0 SPOD /SPFMA SOCD SPFMA SPLS1 /SPFMB SPLS2 SPFMB SPFSET GND2
3 25 2 26 1 22 11 20 13 15 10
2 +24V3 1 /SPFC
1 2
SPF PWB
CNA B12B-PHDSS-B 1 VAREF 2 SPWS 9 GND2 5 +5V2 4 SPLS1 12 GND2 7 +5V2 6 SPLS2 10 GND2 11 +24V3 3 /SPFS c SRA-01T-3.2 a SRA-21T-3 GY GY SRA-21T-3
179228-4+175694-4 +24V3 /STMPS /STSET GND2 RD 1 BR 2 LB 3 GY 4
SMR-03V-NC+SMP-03V-N 1 VAREF 2 SPWS 3 GND2 1754873+179228-3 +5V2 SPLS1 GND2 1754873+179228-3 +5V2 SPLS2 GND2 1 2 3 1 2 3 1 2 3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
CN1 B26B-PHDSS 2_DATA12_DATA1+ 2_DATA02_DATA0+ 2_CLK2_CLK+ 2_DBL2_DBL+ GND2 FRM_CCD2 CLK_CCD2 PAGE2 ADD_CCD2 TXD_CCD2 RES_CCD2 RXD_CCD2 +3.3V +3.3V +24V3 GND2 +12V1 GND2 +5V2 GND2 +5V2 /CIS_SET
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
DGND SCLK DGND /LST DGND SD0 DGND SD1 DGND SD2 DGND SD3 DGND SD4 DGND SD5 DGND SD6 DGND SD7
CN3 9604S-35F 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
GY b FG
3 6
12 11
Signal name SCOV SPFM1 SPFC SRRC SPED SPPD SPFS STMP SPLS1 SPLS2 SPFVR SOCD SPOD
10
Code SCOV SPFM SPFC SRRC SPED SPPD SPFS STMP SPLS1 SPLS2 SPFVR SOCD SPOD
Name SPF cover switch SPF paper feed motor, paper transport motor SPF paper feed clutch
Function/Operation
Type Transmission type Stepping motor Electromagnetic clutch Electromagnetic clutch Transmission type Transmission type Solenoid Solenoid Transmission type Transmission type Volume resistor Transmission type Transmission type
Note Sensor
SPF cover open/close detection Drives the paper feed roller and the transport roller. (SPF) SPF paper feed section roller ON/OFF control SPF resist roller clutch SPF resist roller ON/OFF control SPF document set detector SPF document presence detection SPF document paper pass detector SPF document paper pass detection 1 SPF document pickup solenoid SPF document pickup FAX finish stamp solenoid Drives the FAX document finish stamp. SPF document length detector 1 SPF document length detection (Short) SPF document length detector 2 SPF document length detection (Long) SPF document size (Width) SPF document size (Width) detection detection analog data detector SPF open/close detector SPF unit open/close detection SPF paper exit detector SPF paper exit detection
Sensor Sensor
No. 1
2 3 4 5 6 7 8 9 10 11 12
Document resist roller Document resist front sensor (SPPD) Document set sensor Document feed roller Separation plate Document length sensor (SPLS1/SPLS2) Document width detection volume SPF motor Document take-up roller Document exit roller Document exit sensor (SPOD)
Function This is an image sensor unit to scan the back of a document. An image sensor (CIS: Contact Image Sensor) of 7,196 pixels is employed. The scan resolution is 600dppi.LED lights in the unit are reflected onto the document. Lights reflected from the document are passed through the lens to form images on the photoelectric conversion elements. The photo energy is converted into electric energy. This roller makes synchronization between the document lead edge and the scan start position. Detects that a document reaches the resist roller. Detects that a document is set on the tray. Feeds documents. The rubber plate prevents against duplicated feed of documents. Detects the document length to detect the document size. Detects the document width to detect the document guide. Transports a document in the SPF. Picks up a document and transport it to the document feed roller. Discharges a document. Detects document exit. Scan mode Single surface scan/ Duplex scan Single surface scan/ Duplex scan Magnification ratio 100% or above 101% or above High image quality FAX Document transport speed 220mm/sec 110mm/sec 110mm/sec 167.1mm/sec
C. Operational descriptions
(1) Document feed, transport, scan, paper exit, and operating speed
The document fed by the take-up roller is sent through the paper feed roller and the transport roller to the resist roller section. In the resist roller section, the document lead edge and the scan start position are synchronized. The document is transported to the scan section. After being scanned, the document discharged to the document exit tray by the paper exit roller. The document transport speed varies depending on the scan mode and the scan magnification ratio as shown below.
manuals4you.com
Note 2: Replacement reference: Replace by using the SPF counter value as an indication. Paper feed section pickup roller, paper feed roller, separation pad, separation lower mylar lower: 100K or 1 year
7 7 4 3 6 1 2 5
7
(2) Maintenance and parts replacement
No. a Unit SPF unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Parts SPF document stopper solenoid SPF document resist front sensor SPF paper feed cover sensor SPF document set sensor SPF control PWB SPF original length sensor 1 SPF original length sensor 2 SPF original width detection volume PWB Pick-up roller Paper feed roller CIS unit CIS control PWB SPF open sensor SPF original exit sensor Paper exit roller SPF motor Resist roller Resist roller clutch SPF original paper feed solenoid SPF original paper feed clutch Separation mylar lower Separation pad
a. SPF unit 1) Remove the rear cabinet of the scanner section. 2) Disconnect the connector. 3) Disconnect the grounding wire.
2) 1)
5)
1)
3) 4) 3) 1)
5) 5)
AR-EF3
a-2. SPF document resist front sensor a-3. SPF paper feed cover sensor a-4. SPF document set sensor 1) Remove the upper transport unit cover. 2) Remove the sensors.
1)
2)
7) 6)
1)
4) Slide the SPF unit to the bottom, then remove it.
3)
4)
3)
4)
2) 3)
4)
1)
3)
4)
2) 2)
a-5. SPF control PWB 1) Remove the SPF PWB, and remove the SPF control PWB.
1)
2) 3)
a-1. SPF document stopper solenoid 1) Remove the upper transport unit cover.
3) 4)
4) 3) 4)
2)
5)
1) 1)
manuals4you.com
a-6. SPF original length sensor 1 a-7. SPF original length sensor 2 1) Remove the OC cover.
(SPF original width detection volume installation) <1> Extend the original guide to the maximum position. <2> Adjust so that the mark on the width detection pinion gear is fitted with the mark on the volume mounting plate.
2) 1) 3) 4) 3) 1)
2) Remove the original length sensor cover, and remove the sensor.
1) 2) 1)
4) 4) 3) 3)
<3> Fix the mounting plate with the screw. When the rotational volume sensor is replaced, the sensor value must be adjusted to the paper size (mark on the tray). (Refer to the SIM 53-6 or 53-7.) a-9. Pick-up roller a-10. Paper feed roller 1) Remove the upper transport unit cover. 2) Remove the paper feed roller cover. 3) Remove the hook of each roller, and remove each roller.
a-8. SPF original width detection volume PWB 1) Remove the OC cover. 2) Remove the original length sensor cover. 3) Remove the volume cover and remove the volume.
1)
2)
1) 2) 4)
1) 3) 4)
3)
a-11. CIS unit a-12. CIS control PWB 1) Remove the upper transport unit cover. 2) Remove the CIS unit.
1)
2)
a-14. SPF original exit sensor 1) Remove the paper exit sensor.
1) 2)
When the CIS unit is replaced, the CIS shading adjustment must be performed. (Refer to the descriptions of ADJUSTMENTS.) 3) Remove the harness, the cover, the earth wire, and remove the CIS control PWB. a-15. Paper exit roller 1) Remove the original paper feed unit. 2) Remove the paper exit roller gear.
5) 2)
For easy installation of the cover, slide the earth line to the connector side when attaching. Note: The CIS unit is factory-adjusted before shipping. Since these adjustments cannot be performed in the market, never touch the following screws of the CIS unit.
3) 1)
4)
3) Remove the paper exit frame, and remove the paper exit roller.
6) 5) 3) 7) 2) 1)
3) 4) 3)
manuals4you.com
a-16. SPF motor 1) Remove the OC cover. 2) Remove the SPF lower cover.
1) 3) 1) 2) 1) 1)
2)
1) 1)
1)
3)
1) 4)
a-17. Resist roller a-18. Resist roller clutch 1) Remove the SPF resist roller unit. 3) Remove the original paper feed unit.
2) 1) 2) 3) 2)
2) 2)
2) 2)
2) Remove the SPF resist roller and the SPF resist roller clutch.
2)
2)
1) 2)
3)
1)
2)
a-19. SPF original paper feed solenoid a-20. SPF original paper feed clutch 1) Remove the SPF paper feed unit. 2) Remove the SPF paper guide.
a-21. Separation mylar lower a-22. Separation pad 1) Remove the upper transport unit. 2) Loosen the screw, and remove the separation pad unit.
1) 1)
2)
3) Remove the screw, and remove the separation plate and the front separation plate. 3) Remove the SPF pickup unit. 4) Remove the separation Mylar lower, and the separation pad.
2)
1) 1) 1)
4) Remove the original paper feed solenoid and the SPF original paper feed clutch.
3) 2) 4)
1)
A. General
This section describes various types of settings, display and operation. The LCD display section is controlled by the MFP CONTROL PWB. The touch panel, operation keys and LED display are controlled by the SCANNER CONTROL PWB.
manuals4you.com
OCSW
ORSLED
2
ORS PD /CCFT TOUCH
LCD
1
CN3 TX25-100P-LT-H1 1 GND2 2 GND2 /1_DBL3 /1_DBL+ 4 5 1_CLK6 1_CLK+ 1_DATA07 1_DATA0+ 8 1_DATA19 10 1_DATA1+ 11 GND2 12 GND2 13 GND2 14 GND2 15 GND2 16 GND2 17 (NC) 18 +12V1 19 +24V3 20 +24V3 21 PDSEL1 22 PDSEL2 23 /KEYIN 24 SEG0 25 GND2 26 GND2 27 LcdS+ 28 LcdSLcdM+ 29 LcdM30 31 LcdCP1+ 32 LcdCP1LcdCP2+ 33 34 LcdCP2LcdD0+ 35 LcdD036 LcdD1+ 37 38 LcdD139 LcdD2+ LcdD240 LcdD3+ 41 LcdD342 GND2 43 GND2 44 45 YH 46 /XL 47 /STSET /STMPS 48 49 GND2 50 GND2 GND2 51 GND2 52 +12V1 53 +12V1 54 GND2 55 +5V2 56 GND2 57 +5V2 58 GND2 59 +3.3V 60 FRM_CCD1 61 CLK_CCD1 62 TXD_CCD1 63 RES_CCD1 64 RXD_CCD1 65 ADD_CCD1 66 67 GND2 68 PAGE1 69 GND2 70 GND2 /CL1 71 PDSEL0 72 +5V2 73 PD 74 SEG1 75 SEG2 76 GND2 77 /F0 78 GND2 79 /F1 80 GND2 81 /F2 82 GND2 83 /F3 84 GND2 85 /BZR 86 GND2 87 88 +5V1 89 Lcd DIS +3.3V 90 GND2 91 LCD-VEE 92 TH 93 /CCFT 94 /YL 95 XH 96 +24V3 97 +24V3 98 GND2 99 GND2 100
BOARD TO BOARD
SCN JNT
CN4 20FLS-SM1-TB 1 GND2 2 (NC) 3 (NC) 4 (NC) 5 (NC) 6 GND2 7 LCD D3 8 LCD D2 9 LCD D1 10 LCD D0 11 GND2 12 LCD-VEE 13 3.3V 14 Lcd DIS 15 GND2 16 LCD CP2 17 GND2 18 LCD CP1 19 LCD M 20 LCD S
PWB
(1/2)
CN1 30FMZ-BT XH /YL /XL YH /CCFT +24V3 GND2 TH
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
CN5 30FMN-BT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
XH /YL /XL YH /CCFT +24V3 GND2 TH GND2 LcdD3LcdD3+ LcdD2LcdD2+ LcdD1LcdD1+ LcdD0LcdD0+ LCD-VEE 3.3V LcdDIS GND2 LcdCP2LcdCP2+ GND2 LcdCP1LcdCP1+ LcdMLcdM+ LcdSLcdS+
LVDS PWB
/CCFT HV
1 2
BR LB PL BL BR GY
CN101 T24FAZ-SMT-TF 24 GND2 PDSEL0 23 PDSEL1 22 PDSEL2 21 +5V2 20 19 PD GND2 18 17 +5V2 /KEYIN 16 15 SEG0 14 SEG1 13 SEG2 12 /F0 11 /F1 10 /F2 9 /F3 GND2 8 GND2 7 6 GND2 5 (NC) 4 (NC) 3 /BZR 2 +5V1 1 GND2
CN4 T24FAZ-SMT-TF 1 GND2 2 PDSEL0 3 PDSEL1 4 PDSEL2 5 +5V2 6 PD 7 GND2 8 +5V2 9 /KEYIN 10 SEG0 11 SEG1 12 SEG2 13 /F0 14 /F1 15 /F2 16 /F3 17 GND2 18 GND2 19 GND2 20 (NC) 21 (NC) 22 /BZR 23 +5V1 24 GND2
CN1 TX24-100R-LT-H1 1 GND2 2 GND2 3 /1_DBL4 /1_DBL+ 5 1_CLK6 1_CLK+ 7 1_DATA08 1_DATA0+ 9 1_DATA110 1_DATA1+ 11 GND2 12 GND2 13 GND2 14 GND2 15 GND2 16 GND2 17 (NC) 18 +12V1 19 +24V3 20 +24V3 21 PDSEL1 22 PDSEL2 23 /KEYIN 24 SEG0 25 GND2 26 GND2 27 LcdS+ 28 LcdS29 LcdM+ 30 LcdM31 LcdCP1+ 32 LcdCP133 LcdCP2+ 34 LcdCP235 LcdD0+ 36 LcdD037 LcdD1+ 38 LcdD139 LcdD2+ 40 LcdD241 LcdD3+ 42 LcdD343 GND2 44 GND2 45 YH 46 /XL 47 /STSET 48 /STMPS 49 GND2 50 GND2 51 GND2 52 GND2 53 +12V1 54 +12V1 55 GND2 56 +5V2 57 GND2 58 +5V2 59 GND2 60 +3.3V 61 FRM_CCD1 62 CLK_CCD1 63 TXD_CCD1 64 RES_CCD1 65 RXD_CCD1 66 ADD_CCD1 67 GND2 68 PAGE1 69 GND2 70 GND2 71 /CL1 72 PDSEL0 73 +5V2 74 PD 75 SEG1 76 SEG2 77 GND2 78 /F0 79 GND2 80 /F1 81 GND2 82 /F2 83 GND2 84 /F3 85 GND2 86 /BZR 87 GND2 88 +5V1 89 Lcd DIS 90 +3.3V 91 GND2 92 LCD-VEE 93 TH 94 /CCFT 95 /YL 96 XH 97 +24V3 98 +24V3 99 GND2 100 GND2
BL GY LB RD BR LB
Name
Function/Operation Display the each memu and the information. Various adjustments and setting operation are performed. Generates the document size detection signal. Generates the document size detection signal. Document size detection trigger LCD backlight
Type
Note
Document size detection light emitting PWB Document size detection light receiving PWB OCSW SPF open/close detector /CCFT LCD backlight
No. 1 2
Function Generates the LCD display signal and a high voltage for the backlight. Controls the display operation panel. 3) Remove the document size detection PWB (Light emitting side)
1)
1)
1)
2) 3)
a-2. Original size detection PWB (Light receiving side) 1) Remove the operation panel lower cabinet. 2) Remove the original size detection PWB (Light receiving side)
2) 2) 2)
3)
3) 4)
2)
b. Operation panel unit 1) Remove the original exit tray.
1)
2)
1)
manuals4you.com
b-1. LVDS PWB 1) Remove the operation panel unit. 2) Remove the connector and the screw, and remove the LVDS PWB.
2) 1) 1)
3) Remove the scanner right cabinet.
2) 1) 1)
4) Remove the operation panel lower cabinet.
1) Remove the operation panel unit. 2) Remove the MFP operation PWB
2) 1) 2) 2) 2) 2) 1)
3)
1) 2) 1) 1)
1) 1) 2)
1)
1)
2) 1)
9. Filter
A. Maintenance and parts replacement
(1) Maintenance list
Unit name Filters No. 1 Part name Ozone filter When calling 100K L 200K L 300K L 400K L 500K L 600K L 700K L 800K L Remark
a-1. Ozone filter 1) Remove the paper exit tray cabinet cover, and remove the ozone filter.
manuals4you.com
1 1
a. Drive unit 1) Remove the screw, and remove the left door.
a-1
a-1 a-1
2) Remove the screw, and remove the rear cabinet.
a-2
b-2
Remove the resist roller unit, and apply grease to the bottom section of the PS front roller section brake.
4) Remove the connector and the screw, and remove the main drive unit. a-3. Paper transport clutch a-4. Resist roller clutch 1) Remove the main drive unit. 2) Remove the parts.
a-1. Gears 1) Remove the main drive unit. 2) Remove the screw, and remove the drive cover.
manuals4you.com
4) Remove the connector, the paper cassette paper feed clutch unit, the paper transport clutch unit, and the resist roller clutch unit.
a. Power unit b-1. Drum motor b-2. Main motor 1) Remove the screw, and remove the rear cabinet. 1) Remove the main switch mounting plate. 2) Remove the screw, and remove the right cabinet.
2) Remove the connector and the screw, and remove the drum motor and the main motor.
a-1. Reactor PWB (200V only) / Filter PWB (Taiwan only) 1) Remove the power unit. 2) Remove the connector and the PWB supporter, and remove the filter PWB. (200V only)
(Taiwan only)
6) Remove the connector, the screw, and the angle. Remove the snap band. a-2. Power PWB 1) Remove the power unit. 2) Remove the connector, the screw, and the PWB supporter, and remove the power PWB.
manuals4you.com
a-3. Relay PWB 1) Remove the power unit. 2) Remove the connector and the bushing, and remove the filter PWB mounting plate.
3) Remove the screw, and remove the main switch mounting plate.
3) Remove the connector and the PWB supporter, and remove the relay PWB.
b-2. Cooling fan motor 1) Remove the power unit. 2) Remove the connector and the screw, and remove the duct holding cover. b-1. Main switch 1) Pull out the No. 1 paper feed tray unit, and push up and remove the front door.
2) Release the lock, and pull out the left door. Remove the screw, and remove the front cover right.
When installing the fan, check the indication arrow and note the fan direction.
b-3. Fuse PWB 1) Remove the screw, and remove the rear cabinet.
3) Remove the connector and the screw, and remove the high voltage PWB.
2) Remove the connector and the screw, and remove the inlet mounting plate.
12. PWB
A. Maintenance and parts replacement
No. a Unit 1 2 3 4 Parts MFP controller PWB HDD (Option) PCU PWB Mother PWB
3) Remove the connector and the screw, and remove the fuse PWB.
a-1 a-3
a-2 a-4
b-4. High voltage PWB 1) Remove the rear cabinet. 2) Remove the connector and the screw, and remove the PCU PWB unit.
a-1. MFP controller PWB 1) Remove the screw, and pull out the MFP controller PWB unit. 2) Remove the connector.
manuals4you.com
3) Release the lock, and remove the MFP controller PWB unit.
3) Remove the connector, and remove the screw. 4) Remove the screw, and remove the MFP controller PWB. 4) Pull out the HDD unit.
5) Remove the screw, and remove the HDD cover. 6) Remove the screw, and remove the HDD angle.
a-2. HDD (Option) 1) Remove the screw, and remove the right cabinet.
a-3. PCU PWB 1) Remove the screw, and remove the rear cabinet.
2) Remove the connector and the screw, and remove the PCU PWB. When replacing the PCU PWB, replace the EEPROM on the PCU PWB which is to be replaced.
Unit 1 2 3
a-4. Mother PWB 1) Remove the fusing unit. 2) Remove the paper exit reverse unit. 3) Remove the front cover right. 4) Remove the HDD cover. 5) Remove the MFP controller PWB unit. 6) Remove the cooling duct. 7) Remove the controller duct. 8) Remove the screw and the connector, and remove the main duct, the sub duct, and the box cooling duct lower.
Parts Controller cooling fan motor 1 Controller cooling fan motor 2 Ozone exhaust fan motor
a-2 a-3
a-1
a-1. Controller cooling fan motor 1 a-2. Controller cooling fan motor 2 1) Pull out the left door.
manuals4you.com
10) Remove the snap band, the screw, and the connector, and remove the fan fixing plate. 11) Remove the screw, and remove the controller cooling fan motor 1.
3) Remove the screw, and remove the paper exit upper cabinet. 4) Remove the screw, and remove the left rear cabinet. 5) Remove the screw, and remove the front left upper cabinet. When installing the fan, note the fan direction. 12) Remove the connector and the screw, and remove the controller cooling fan motor 2.
6) Remove the screw, and remove the paper exit tray cabinet. 7) Remove the screw, and remove the front right upper cabinet. 8) Remove the front door. When installing the fan, note the fan direction. a-3. Ozone exhaust fan motor 1) Pull out the left door. 2) Remove the rear cabinet. 3) Remove the paper exit upper cabinet, the left rear cabinet, and the front left upper cabinet. 4) Remove the paper exit tray cabinet, the front right upper cabinet, and the front door. 5) Remove the screw, and remove the controller duct. 6) Remove the connector and the screw, and remove the ozone exhaust fan motor.
9) Remove the screw, and remove the cooling fan duct upper.
When installing the fan, check the indication arrow and note the fan direction. AR-M351U/M451U, AR-M355U/M455U MAINTENANCE AND DETAILS OF EACH SECTION 7 - 75
[8] ADJUSTMENTS
No. Section 1 Process section 2 Image check, adjustment A B C A Adjustment item Doctor gap adjustment MG roller main pole position adjustment High voltage output adjustment Adjustments <1> LSU right angle on the engine adjustment side <2> Print off-center adjustment <3> Each tray resist amount setting <4> Self print lead edge adjustment <5> Front/rear and left/right void amount setting Adjustment <1> OC scan distortion on the adjustment scanner side <2> SPF height adjustment <3> SPF scan distortion adjustment <4> OC scan magnification ratio adjustment <5> SPF scan magnification ratio <6> OC scan lead edge adjustment <7> SPF scan lead edge adjustment <8> Original off-center adjustment OC scan distortion adjustment Vertical image distortion balance adjustment Vertical image distortion balance adjustment Vertical (sub scanning direction) distortion adjustment Height adjustment of original detection light emitting unit Original size detection photo sensor check Original size detection photo sensor adjustment Image density adjustment DSPF width detection adjustment
7) Check the developing doctor gap. If the clearance is within the specified range, fix the screw with screw lock. 8) After completion of the job, apply screw lock.
20mm 20mm
Scanner section
A B C D E F G H I
<Adjustment specification> Specification Both sides (Position at 20 - 50mm) Center 0.450.03mm 0.45 - 0.60mm Ambient temperature 5 - 30C
1. Process section
A. Doctor gap adjustment
This adjustment is performed in the following cases: When developer is scattered. When an uneven image is produced. 1) Remove the developer cartridge and the developing unit from the machine. 2) Remove the DV cover and the developer from the developing unit. 3) Remove the DVR cover, the DVF handle, the idle correction plate assembly, and the HG gear 22T, insert a thickness gauge (0.46mm) as shown in the figure below, and check that the clearance is within the specified range. If the clearance is not within the specified range, adjust the doctor gap in the following procedures. 4) Loosen the developing doctor fixing screw A. 5) Insert the thickness gauge (0.46mm) again as shown in the figure below. 6) Push the developing doctor in the arrow direction and tighten the fixing screw.
manuals4you.com
<Adjustment specification> Marking position Measure from the P surface above. Specification 54.2mm
Default Monitor output voltage MC grid MAIN GRID (SIM 8-2) AUTO CHARACTER MIX PHOTO PRINTER FAX FRONT BACK Developing bias DV BIAS (SIM 8-1) AUTO AE mode Text mode Text/Photo mode Photo mode Printer mode Fax mode Front Back AE mode 45PPM: -650V5V 35PPM: -620V5V -650V5V -650V5V -650V5V -650V5V -650V5V Set value 45PPM: 645 35PPM: 615 645 645 645 645 645 45PPM: 267 35PPM: 220 45PPM: 310 35PPM: 267 485 485 485 485 485 485 150 45PPM: 160 35PPM: 120 45PPM: 160 35PPM: 120 780 Set range 200~900 200~900 200~900 200~900 200~900 200~900 0~620 0~620 0~745 0~745 0~745 0~745 0~745 0~745 0~255 0~240 0~240 0~1250
45PPM: -500V5V 35PPM: -470V5V CHARACTER Text mode -500V5V MIX Text/Photo mode -500V5V PHOTO Photo mode -500V5V PRINTER Printer mode -500V5V FAX Fax mode -500V5V PLUS Positive bias +150V5V Separation voltage SHV FRONT Front 45PPM: +0.220.1V (SIM 8-17) 35PPM: +1.37V0.1V BACK Rear 45PPM : +0.220.1V 35PPM: +1.37V0.1V Transfer voltage THV -800V10V (SIM 8-17)
CN2-1
100M
CN2-3
10M
CN2-5
10G
Center line
Standard paper of A3
4) Check each output copy. (Image distortion/ each void/ lead edge position/ Off-center/ Magnification ratio/ Density/ Dirt, etc.) 5) If there is no problem in copy images, the image check is completed.
220mm
manuals4you.com
Adjustment position Tray 1 Tray 2 Tray 3 Tray 4 MFT ADU Tray 1 Tray 2 Tray 3/LCC left Tray 4/LCC right Manual feed Duplex
Specification 01.5mm
Default 50
For the duplex mode (Single Duplex), add 10 to the above set value. When the print line is shifted toward a from the paper center, decrease the value. When the print line is shifted toward b from the paper center, increase the value.
3) Press [START] key. When [START] key is pressed, the adjustment value is set and paper feed and copying are performed. 4) Adjust the resist quantity so that paper is transferred stably.
SIMULATION 51-2 RESIST TIMING ADJUSTMENT. SELECT 0-8, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.TRAY1 60 3.TRAY2 50 4.DESK 50 5.BPT 55 6.ADU 50 7.SPF(HIGH) 60 8.SPF(LOW) 75
ation or skew for each tray. Items which must have been completed before this adjustment. LSU right angle adjustment (If there is no distortion in self print, the adjustment is not required.) Print off-center adjustment Items which must be executed after completion of this adjustment. Print lead edge adjustment Front/rear and left/right void amount setting 1) Execute SIM 51-2. 2) Enter the resist adjustment value with 10-key.
Item 2 TRAY1 3 TRAY2 4 DESK 5 BPT 6 ADU Tray 1 resist adjustment value Tray 2 resist adjustment value Desk resist adjustment value Manual tray resist adjustment value ADU resist adjustment value
[Output pattern]
When the set value is increased, the warp amount of paper is increased. When the adjustment value is decreased, the warp amount of paper is decreased.
adjustment value of DENA, and press [P] key.) 3) Check the lead edge void area on the self print pattern (SIM67-1). (Enter 1 and press [START] key.) 4) If the adjustment result is not satisfactory, perform the following procedures.
If the lead edge void area is not 3.5mm:
DENA, and press [P] key.) (0.1mm/step) 2) Make a copy at the normal ratio (100%) and check the lead edge void area and the image loss. (Enter 100 as the set value of the copy magnification ratio (MAGNIFICATION), and press [START] key.) 3) If the adjustment result is not satisfactory, perform the following procedures.
If the lead edge void are is not 3.5mm:
Change the adjustment value of RRCB and perform the adjustment. (Change the adjustment value of RRCB and press [START] key.) (Shift for the adjustment value change: 0.1mm/step)
SIMULATION 50-5 LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START (ADJUSTMENT DATA) LEAD EDGE: 2.RRCB 50 3.SIDE2 ADJ. 50 RESIST: 4.T1 50 5.T2 50 6.DESK 50 7.BPT 50 8.ADU 50 OFF CENTER: 9.T1 50 10.T2 50 11.T3 50 12.T4 50 13.BPT 50 14.ADU 50 (VOID SETTING) 15.LEAD_EDGE(DENA) 50 16.TRAIL_EDGE(DENB) 30
Change the adjustment value of RRCB and perform the adjustment. (Change the adjustment value of RRCB and press [START] key.) (1msec/step)
If the lead edge image loss is not 1.5mm:
Change the adjustment value of RRCA and perform the adjustment. (Change the adjustment value of RRCA and press [START] key.) (Shift for the adjustment value change: 0.2mm/step) (Rear edge void area adjustment) Adjust so that the rear edge void area is 3.5mm. (Change the adjustment value of TRAIL EDGE, and press [START] key.) (Front/rear frame direction image loss adjustment) Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment value of SIDE, and press [P] key.) When the adjustment value is changed, the image position is shifted in the front/rear frame direction.
17.FRONT/REAR 30
<Specification> Self print lead edge adjustment SIM 50-5 Set position Print start position A of the output pattern 1 Specification A = 4.0mm or less (Lead and tail total: 8.0mm or less) Set value Shift of 0.175mm (35ppm) / 0.225mm (45ppm) for set value 1.
(Front/rear frame direction void area adjustment) Adjust so that the total of the front/rear direction void areas is 7.0mm. (Change the adjustment values of FRONT/REAR, and press [START] key.) Front frame void area = 3.5mm Rear frame void area = 3.5mm If, as shown above, the front and the rear void areas are not even, use SIM 50-5 to adjust the image off-center position.
manuals4you.com
SIMULATION 50-1 LEAD EDGE ADJUSTMENT. SELECT 0-9, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100 (ADJUSTMENT DATA) 3.RRCA 50 4.RRCB 50 10.SIDE2 ADJ. 50 (IMAGE LOSS SETTING) 5.LEAD 15 6.SIDE 20 (VOID SETTING) 7.LEAD_EDGE(DENA) 50 8.TRAIL_EDGE(DENB)30 9.FRONT/REAR 30
<Specification> Set position Lead edge void adjustment LEAD EDGE VOID (DENA) Rear edge void adjustment TAIL EDGE VOID (DENB) Side edge void adjustment FRONT/REAR Output pattern 71 print void quantity A Output pattern 71 print void quantity B Output pattern 71 print void quantity C + D Set value A = 4.0mm or Shift of less 0.1mm (A and B total: for set 8.0mm or less) value 1. B = 4.0mm or less (A and B total: 8.0mm or less) C and D total: 8.0mm or less Specification
B
Print lead edge
A
In the case of Fig. 1 Shift cam A in the direction A by the difference in the copy image. For one scale (one groove), shift by 0.5mm.
After shifting, tighten the fixing screw (M3 x 12) of cam A and make a copy again, and check the copy again to insure that there is no distortion. In the case of Fig. 2 Shift cam A in the direction B by the difference in the copy image. For one scale (one groove), shift by 0.5mm. After shifting, tighten the fixing screw (M3 x 12) of cam A and make a copy again, and check the copy again to insure that there is no distortion. After adjustment, tighten the fixing screw (M3 x 12) and the scanner fixing screw (M4 x 8).
If the above adjustment does not fix the problem, perform the
MB rail adjustment.
After the OC distortion adjustment, perform SIM53-8 SPF scan-
4) Execute SIM51-2 to check the SPF set value. Change the set value of the SPF resist amount to the following value. 7 8 SPF (HIGH) SPF (LOW) 60 75
SIMULATION 51-2 RESIST TIMING ADJUSTMENT. SELECT 0-8, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.TRAY1 60 3.TRAY2 50 4.DESK 50 5.BPT 55 6.ADU 50 7.SPF(HIGH) 60 8.SPF(LOW) 75
5) Though the SPF resist amount is the above value, if there is any distortion in SPF scan, adjust the SPF installing position in the following procedures. 6) Loosen the nut which is fixing the adjustment set screw of the hinge R, and adjust the adjustment set screw. 7) Make a copy again, and check again that the value is in the specified range. 8) Tighten the nut to fix the adjustment screw.
b a
b a
b
b
<Specification> Specification Distance between dove (Reference plate) and table glass 3-point contact (Left front/Left rear/Right front when viewed from the front) Adjustment position Hinge adjustment set screw
a
<Specification> Skew feed Specification Within 3mm Adjustment position Hinge R adjustment screw
manuals4you.com
SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.MAGNIFICATION 100 3.CCD(MAIN) 50 4.CCD(SUB) 50 5.SPF(MAIN) 50 6.SPF(SUB) 50 7.CIS(MAIN) 50
SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.MAGNIFICATION 100 3.CCD(MAIN) 50 4.CCD(SUB) 50 5.SPF(MAIN) 50 6.SPF(SUB) 50 7.CIS(MAIN) 50
<Specification> Specification Main scan direction magnification ratio CCD (MAIN) Sub scan direction magnification ratio CCD (SUB) 0.5% Adjustment Adjustment position value SIM48-1 Set value 1: (3, 4) 0.1% change
SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 4.CCD(SUB)
50
SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 1-15, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)
100
Adjustment Adjustment position value SIM 48-1 Set value 1: (5, 6) 0.1% change
<Specifications> Specifications SPF sub scan direction 0.5% magnification ratio SPF (SUB) DSPF main scan (back) direction magnification ratio CIS (MAIN) OC.
<Document>
Document set reference
Output result
Rear edge void Lead edge void
<Specification>
Item Content Specification Set range 0 - 99 Default
1 2
Paper feed tray selection COPY START Copy START (Default) MAGNIFICATION Print magnification ratio
TRAY SELECT
1 - 99
50
0 - 99
15 20
0 - 99
35
32
(Lead edge adjustment value) 3 SIDE1 Front surface document scan start position adjustment value 4 SIDE2 Back surface document scan start position adjustment value (Image loss set value: SIDE 1) 5 LEAD_EDGE Front surface lead edge image loss set value 6 FRONT_REAR Front surface side edge image loss set value 7 TRAIL_EDGE Front surface rear edge image loss set value (Image loss set value: SIDE 2) 8 LEAD_EDGE Back surface lead edge image loss set value 9 FRONT/REAR Back surface side edge image loss set value 10 TRAIL_EDGE Back surface rear edge image loss set value
50
0 - 99
15 20
0 - 20
0 - 99
15 20
0 - 20
manuals4you.com
<Display values 1> Normal display ERROR display Door open Jam Paper empty NOW COPYING DOOR OPEN. JAM PAPER EMPTY.
For the duplex mode (Single Duplex), add 10 to the above set value. When the print line is shifted toward a from the paper center, decrease the value. When the print line is shifted toward b from the paper center, increase the value. <Specifications> Machine (OC mode) Overall (DSPF) Single Duplex Single S - S Single D - S Duplex S - D Duplex D - D 1.5mm 1.7mm 2.8mm 3.5mm 3.0mm 3.5mm
With the above + 10, the SPF enters the duplex mode (DD),
3. Scanner section
A. OC scan distortion adjustment (MB-B rail height adjustment)
This adjustment requires a high-level preciseness. It is easier to perform the scanner unit distortion adjustment previously described. Before performing this adjustment, the following adjustment must have been completed. LSU right angle adjustment 1) Make a test chart as shown below. (Print a self-print pattern 71.)
2) Make a copy from the table glass, and check it. At that time, set the test chart correctly. If it is set in a distorted position, the adjustment cannot be made correctly. 3) If the output value is not in the specified range, perform the following adjustment. 4) Remove the front cabinet in front of the scanner, and check that installing position of the MB rail. 5) Loosen the screw at the right of the MB rail to adjust.
Specification 1.5mm
SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100 (ADJUSTMENT DATA) 3.PLATEN 50 4.SPF SIDE1 50 5.SPF SIDE2 50
Adjustment position Original PLATEN off-center SPF SIM50-12 SIDE1 SPF SIDE2 OC mode SPF front surface adjustment SPF back surface adjustment
Set value Specification As shone in the table below. Default Range 50 0 99 Set value 1: 0.1mm shift
B. Vertical image distortion balance adjustment (Copy lamp unit installing position adjustment)
1) Insert the front/rear mirror base drive wire into the frame groove and press and fix it with the wire holder. At that time, do not tighten the wire fixing screw. Change the direction of the lamp positioning plate. (F and R) 2) Push the copy lamp unit onto the positioning plate, and tighten the wire fixing screw.
D. Vertical (sub scanning direction) distortion adjustment [Winding pulley position adjustment]
This adjustment is executed in the following cases: When the mirror base drive wire is replaced. When the lamp unit, or No. 2/3 mirror holder is replaced. When a copy shown below is made.
La
Lb
Original
Copy
A3 white paper
C. Vertical image distortion balance adjustment (No. 2/3 mirror base unit installing and position adjustment)
This adjustment is to adjust the parallelism of the mirror base to the OPC drum surface and the original surface. 1) Manually turn the mirror base drive pulley to bring mirror base B into contact with mirror base positioning plate. If, at that time, the front frame side and the frame side of mirror base B are brought into contact with the mirror base positioning plate simultaneously, the parallelism is correct and there is no need for adjustment.
2) With the original cover open, make a normal (X 1.0) copy. 3) Measure the black distance at the lead edge and the rear edge of the copy paper.
Paper exit direction La : Lead edge black background section Lb : Rear edge black background section
If La = Lb, the procedures 4) through 7) are not required.
manuals4you.com
4) Loosen the fixing screw of the front or the rear frame mirror base drive pulley. If La < Lb, turn the rear frame mirror base drive pulley in direction B. (Do not move the mirror base drive pulley shaft.) If La > Lb, turn the rear frame mirror base drive pulley in direction A. (Do not move the mirror base drive pulley shaft.)
5) After completion of adjustment, press the original detection light emitting unit fully downward with your finger and release it. Check that the original detection light-emitting unit moves up smoothly. <Specification> Specification Adjustment position Original size 320.5mm Height adjustment SIM 41-3 detection position screw
Rear side
A
PD4
PD5
PD6
PD7
5) Tighten the fixing screw of the mirror base drive pulley. 6) Perform procedures 1) through 3). 7) If La is not equal to Lb, perform procedures 4) and 5). If La = Lb, the adjustment is completed. Repeat procedures 1) through 6) until La = Lb.
home position. 2) Open the document cover. Select 1 without placing paper on the table glass, and press START. 3) When COMPLETE is displayed on the LCD, press CUSTOM SETTING to return to the initial screen. 4) Place A3 (or WLT) paper on the table glass, select 2 and press START. When COMPLETE is displayed, the adjustment is normally completed.
If ERROR is displayed, the error PD sensor is displayed.
SIMULATION 41-2 PD SENSOR ADJUSTMENT. SELECT1-2, AND PRESS START. (PLEASE OPEN THE ORIGINAL COVER.) 1. NO ORIGINAL 2. A3 ORIGINAL
manuals4you.com
320.5mm
SIMULATION 41-2 PD SENSOR ADJUSTMENT. NO ORIGINAL COMPLETE (or "ERROR at PD1 PD2...") A3 ORIGINAL INCOMPLETE
Select 2 and press [START] key. (Error) Press [CUSTOM SETTINGS] key.
3) Open the original detection light-emitting unit gradually to check the height at which OCSW display turns to the normal state. 4) If the heights are out of the specified range in procedures 2) and 3), adjust the height of the original detection light emitting unit by shifting the adjustment screw.
SIMULATION 41-3 PD SENSOR DATA DISPLAY. OCSW PD1[128]: 200 PD2[128]: 200 PD3[128]: 50 PD4[128]: 52 PD5[128]: 51 PD6[128]: 50 PD7[128]: 52
SIMULATION 41-2 PD SENSOR ADJUSTMENT. NO ORIGINAL COMPLETE A3 ORIGINAL COMPLETE (or "ERROR at PD1 PD2...")
<Specification> Document size detection photo sensor adjustment Specification COMPLETE Adjustment SIM 41-2
UKOG-0162FCZZ
SIM46-14
10
Test chart comparison UKOG1 2 3 4 5 6 0162FCZZ DENSITY No. 0.1 0.2 0.3 UKOG0089CSZZ DENSITY No. KODAK GRAY 1 2 3 SCALE SHARP CORPORATION MADE IN JAPAN b. Density adjustment procedure <1> Collective adjustment of two or more copy quality modes SIM46-16 Normally this adjustment is performed with SIM 46-2. In this method, two or more copy density adjustments in different modes can be adjusted collectively. 1) Execute SIM 46-2. (Binary value mode) Quality mode AE3.0 (AE) CH3.0 (Character) MIX3.0 (Character/Photo) PH3.0 (Photo) SIM46-45 Linked simulation data SIM46-9 SIM46-10 SIM46-11 7 8 9 10 W
Fine mode
SIM46-15
0.5 1.9 0
19
600dpi mode
manuals4you.com
This adjustment is used when a different density level for different copy quality mode is required. SIM 46-5 to -7 and SIM 46-9 to -11 are used. 1) Execute the simulation corresponding to the copy quality mode to be adjusted.
SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). SELECT 0-11, AND PRESS START. 0. TRAY SELECT 1 1. COPY START 2. EXP LEVEL 1 3. 1.0 50 4. 1.5 50 5. 2.0 50 6. 2.5 50 7. 3.0 50 8. 3.5 50 9. 4.0 50 10. 4.5 50 11. 5.0 50
SIMULATION 46-2 EXP. LEVEL SETUP (2). INPUT VALUE 0-99, AND PRESS START. 3. AE 3.0
50
SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). INPUT VALUE 0-99, AND PRESS START. 3. 1.0
50
SIMULATION 46-2 EXP. LEVEL SETUP (2). SELECT 1-5, AND PRESS START. (FEED TRAY) 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT
Select 2, and press [START] key.
SIMULATION 46-2 EXP. LEVEL SETUP (2). SELECT 3-6, AND PRESS START. (EXP. LEVEL SELECT) 3. AE 3.0 4. CH 3.0 5. MIX 3.0 6. PHOTO 3.0
2) Press the COPY button to make a copy. Check that the copy density is as shown in the table below. If not, change the adjustment value. Adjustment spec Mode Character Character/ Photo Photo Auto EXP. 3 3 3 Chart No. 3 3 3 3 Adjustment Chart Adjustment level No. level Copied 2 Not copied Copied 2 Not copied Copied Copied 2 2 Not copied Not copied
SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). SELECT 1-5, AND PRESS START. (FEED TRAY) 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT
SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). SELECT 3-11, AND PRESS START. (EXP. LEVEL SELECT) 3. 1.0 4. 1.5 5. 2.0 6. 2.5 7. 3.0 8. 3.5 9. 4.0 10. 4.5 11. 5.0
2) Press the COPY button to make a copy Check that the copy density is as shown in the table below. If not, change the adjustment value. For the auto mode, there is only one adjustment value. For the other modes, the adjustment value for each density level must be adjusted.
If the copy density is too light, increase the adjustment value. If the copy density is too dark, decrease the adjustment value. Adjustment range: 30 - 170
(Fax mode image density adjustment items) Simulation for adjustment IndividualAll-mode mode adjustment adjustment 46-12 46-13
Image mode
Fax mode print density adjustment (standard mode) Fax mode print density adjustment (smallcharacter mode) Fax mode print density adjustment (fine mode)
Fax mode print density adjustment (super fine mode) Fax mode print density adjustment (600dpi mode)
Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode
46-14
SIMULATION 46-12 EXP.LEVEL SETUP FAX(AUTO SET), INPUT VALUE 0-99, AND PRESS START. 2.FAX EXP.LEVEL
50
46-15
46-16
SIMULATION 46-12 EXP.LEVEL SETUP FAX(AUTO SET).SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
(Fax mode density) The print density settings should be normally left at defaults but should be adjusted according to user requests, if any. a. Adjust the fax mode print density for all modes at once 1) Set the test chart (UKOG-0162FCZZ) on the original table so that it aligns with the front frame. Then put four or five pieces of A3 (11" x 17") paper .
TRAY SELECT Paper feed tray selection COPY START Copy START (Default) FAX EXP. LEVEL FAX mode print density 0 - 99
50
3) Select the adjustment item (FAX EXP. LEVEL) using the numeric keypad. 4) Press the Start key. 5) Press the Start key (A copy is created.) Check the print density. If the print density is not at an acceptable level, do the following steps. 6) Enter the print adjustment value using the numeric keypad. 7) Press the P or Start key This applies the adjustment value. Pressing the Start key starts print operation as well as applying the adjustment value. 8) Check the print density. Repeat steps 6 to 8 until an acceptable print density is obtained. Note: Adjusting the Fax print density through this simulation changes the print density settings for all Fax modes to the density level applied by carrying out this simulation. The Fax mode print density settings for individual Fax modes adjusted through Simulations 46-13, -14, -15, -16 and -45 are changed to the print density level applied by this simulation.
00
manuals4you.com
b. Adjust the fax mode print density (standard mode/ small-character mode/super fine mode/600dpi mode) This adjustment is intended to the print mode for each Fax mode individually. In manual mode, the print density setting for each print density adjustment level (1 to 5) can be adjusted to a custom density level. 1) Set the test chart (UKOG-0162FCZZ) on the original table so that it aligns with the front frame. Then put four or five pieces of A3 (11" x 17") paper . 0 1 2 3 4 5 6 7 8 TRAY SELECT PRINT START EXP LEVEL AUTO 1.0 2.0 3.0 4.0 5.0
Item Paper feed tray selection Print start (Default) Exposure level selection Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5
Set range
Default
0 - 99
50
00
SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE).SELECT 0-14,AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50 9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50 12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50
Select other than 0 - 2, and press [START] key.
2) Go through the simulation modes that correspond to the Fax modes for which to adjust the print density (i.e., the modes specified in Simulations 46-13, -14, -15, -16, or -45).
SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL). SELECT 0-8, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50
SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE),INPUT VALUE 0-99, AND PRESS START. 4.1.0
50
Select 1, Press [START] key. and press Press [CUSTOM SETTINGS] key, [START] key. or terminate copying.
Select 0, and press [START] key. Select other than 0 - 2, and press [START] key. Press [CUSTOM SETTINGS] key.
SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL),INPUT VALUE 0-99, AND PRESS START. 4.1.0
Select 1, Press [START] key. and press Press [CUSTOM SETTINGS] key, [START] key. or terminate copying.
SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE). SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
50
SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE). SELECT 3-14, AND PRESS START. (EXP.LEVEL SELECT) 3.AUTO 4.1.0 5.2.0 6.3.0 7.4.0 8.5.0 9.AUTO(H) 10.1.0(H) 11.2.0(H) 12.3.0(H) 13.4.0(H) 14.5.0(H)
SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL). SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT (ABOVE +20:DSPF MODE)
Select 2, and press [START] key.
SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL). SELECT 3-8, AND PRESS START. (EXP.LEVEL SELECT) 3.AUTO 4.1.0 5.2.0 6.3.0 7.4.0 8.5.0
Item 0 1 2 3 4 5 6 7 8 9 10 TRAY SELECT PRINT START EXP LEVEL AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H) Paper feed tray selection Print start (Default) Exposure level selection Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)
0 - 99
50
1) Extend the guide to MAX. position, select 1, and press START. When COMPLETE is displayed, press CUSTOM SETTING to return to the initial screen. 2) Move the guide to A4R position, select 2, and press START. When COMPLETE is displayed, press CUSTOM SETTING to return to the initial screen. 3) Move the guide to A5R position, select 3, and press START. When COMPLETE is displayed, press CUSTOM SETTING to return to the initial screen. 4) Move the guide to MIN. position, select 4, and press START. When COMPLETE is displayed, the adjustment is completed. If ERROR is displayed in procedures 1) - 4), repeat the adjustment again.
SIMULATION 53-6 SPF TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START. 1.MAX.POSITION 2.POSITION 1 3.POSITION 2 4.MIN.POSITION
Select 1, and press [START] key.
3) Using the numeric keypad, select the number that corresponds to the adjustment item. Choose from numbers 3 to 8 (14). Auto mode Manual mode (print density adjustment level) For manual mode, select the number that corresponds to the print density level (1 to 5). (Choose from numbers (4 to 8) (1014)). 4) Press the Start key 5) Press the Start key. (A copy is created.)
SIMULATION 53-6 SPF TRAY ADJUSTMENT. MAX.POSITION ... COMPLETE (or ERROR)
SIMULATION 53-6 SPF TRAY ADJUSTMENT. POSITION 1 ... COMPLETE (or ERROR)
SIMULATION 53-6 SPF TRAY ADJUSTMENT. POSITION 2 ... COMPLETE (or ERROR)
Select 4, and press [START] key. Press [CUSTOM SETTINGS] key.
SIMULATION 53-6 SPF TRAY ADJUSTMENT. MIN.POSITION ... COMPLETE (or ERROR)
SIMULATION 53-7 SPF TRAY ADJUSTMENT(MANUAL). INPUT VALUE 0-1023, AND PRESS START. 1.MAX.POSITION
66
manuals4you.com
[9] SIMULATION
1. Outline and purpose
The simulation has the following functions to grasp the machine operating status, identify the trouble position and causes in an earlier stage, and make various setups and adjustments speedily for improving the serviceability of the machine. 1) Various adjustments 2) Setup of specifications and functions 3) Canceling troubles 4) Operation check 5) Various counters check, setup, and clear 6) Machine operating status (operation history) data check, clear 7) Transfer of various data (adjustments, setup, operations, counters) The operating procedures and the displays differ depending on the form of the operation panel of the machine.
2. Code-type simulation
A. Operating procedures and operations
Entering the simulation mode 1) Copy mode key ON Program key ON Asterisk (*) key ON CLEAR key ON Asterisk (*) key ON Ready for input of a main code of simulation 2) Entering a main code with the 10-key START key ON 3) Entering a sub code with the 10-key START key ON 4) Select an item with the scroll key and the item key. 5) The machine enters the mode corresponding to the selected item. Press START key or EXECUTE key to start the simulation operation. To cancel the current simulation mode or to change the main code and the sub code, press the user setup key. Canceling the simulation mode to return to the normal mode 1) Press CA key.
Press the asterisk (*) key. Standby for entry of SIM code. Enter the main code of SIM with the 10-key. The main code of SIM is displayed.
NO
Standby for entry of SIM sub code Enter SIM sub code with the 10-key.
YES
Select the mode and the item with the scroll key and the item key.
NO
YES
Operation check ?
Press the EXECUTE button and OK button. Do you want to end the simulation ?
YES
NO
YES
The display is made according to the selected some and the item.
Data clear ?
YES
Press the EXECUTE button and OK button. The selected mode and the item are cleared.
NO
YES
NO
Operation is made according to the selected mode and the item. (Other modes)
The display is made according to the selected mode and the item. Do you want to change the content ?
YES NO
The changed content is stored. Press the EXECUTE button and OK button.
manuals4you.com
B. Simulation list
(1) Main/ Sub
Code Main Sub 1 1 2 Function (Purpose)
Function (Purpose) Used to cancel the self-diag "U1" trouble. (Only when FAX is installed.) Used to cancel excluding the self-diag U1/LCC/ U2/PF troubles. Used to cancel the self-diag "U6-01, 02, 03, F312, 22" (large capacity paper feed tray, paper feed trays 1, 2) troubles. Used to cancel the self-diag U2 troubles. Used to cancel the PF troubles (when the copy inhibit command from the host computer is received). Used to set the maintenance cycle. Used to check the print count value in each section and each operation mode. (Used to check the maintenance timing.) Used to check the total numbers of misfeed and troubles. (When the number of misfeed is considerably great, it is judged as necessary for repair. The misfeed rate is obtained by dividing this count value with the total counter value.) Used to check misfeed positions and the misfeed count of each position. (If the misfeed count is considerably great, it may be judged as necessary to repair.) Used to check the trouble (self diag) history. Used to check the ROM version of each unit (section). Used to output the list of the setting and adjustment data (simulations, FAX soft switch, counters). Used to display the key operator code. (This simulation is used when the customer forgets the key operator code.) Used to check the number of use of the finisher, the SPF, and the scan (reading) unit. Used to check the number of use (print quantity) of each paper feed section. Used to check the system configuration (option, internal hardware). Used to check the use frequency (send/receive) of FAX. (Only when FAX is installed) Used to check the SPF misfeed positions and the number of misfeed at each position. (When the number of misfeed is considerably great, it can be judged as necessary for repair.) Used to check the operating time of the process section (OPC drum, DV unit, toner bottle). Used to check the values of the counters related to the scan mode and the internet FAX mode. Used to check the trouble history of paper jam and misfeed. (If the number of misfeed and troubles is considerably great, it may be judged as necessary to repair.) Used to check the operations of the sensors and detectors in the paper feed and transport section. Used to clear the misfeed counter, the misfeed history, the trouble counter, and the trouble history. (The counters are cleared after completion of maintenance.) Used to clear the number of use (the number of prints) of each paper feed section. Used to clear the number of use of the finisher, SPF, and the scan (reading) unit. Used to reset the maintenance counter. Used to reset the developer counter. (The developer counter of the DV unit which is installed is reset.)
1 2
2 3 6
10 20 21 4 2
1 2
1 2
1 6 8 1
6 17
10
Used to check the operations of the scanner (read) unit and its control circuit. Used to check the operation of sensor and detector in the scanning (read) section and the related circuit. Used to check the operations of the automatic document feeder unit and the control circuit. Used to check the operations of the sensors and detectors in the automatic document feeder unit and the related circuits. Used to check the operations of the loads in the automatic document feeder unit and the control circuits. Used to check the operation of sensor and detector in the finisher and the related circuit. Used to check the operation of the load in the finisher and the control circuit. Used to adjust the stacking capacity of the finisher. (Used to adjust the alignment plate (jogger) stop position in the finisher paper width direction. The adjustment is made by changing the alignment plate home position in the paper width direction by software.) Console finisher (AR-FN7) adjustment Used to check the mail bin stacker sensor. Used to check the operations of the mail bin stacker loads. Used to check the operations of the sensors and detectors in the paper feed section (desk paper feed/large capacity tray) and the related circuit. Used to check the operations of the loads in the paper feed section (desk paper feed/large capacity tray) and the related circuit. Used to check the operation of the display, LCD in the operation panel, and control circuit. Used to check the operation of the heater lamp and the control circuit. Used to check the operation of the paper transport system loads and the control circuit. Used to check the operations of each fan motor and its control circuit. Used to set the operating conditions of aging. Used to set the intermittent aging cycle. Used to set the warm-up time display YES/NO. Used to check and adjust the operations of the developing voltage of each color and the control circuit. Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit. Used to check and adjust the operation of the transfer voltage and the control circuit. Used to check and adjust the operation of the transfer voltage and the related circuit. (Transfer belt cleaning mode) Used to check and adjust the operation of the load (clutch/solenoid) in the duplex section and the control circuit. Used to check the operations of the sensors and detectors in the duplex section and its control circuit. Used to check the operations of the toner motor and the related circuit.
15
16 17
0 0
21 22
1 1
4 5 6
8 9 10 11 12
13 19 23 2
80 24 1
2 3 4 5
Function (Purpose) Used to reset the copy counter. Used to clear the OPC drum counter. (Perform this simulation when the OPC drum is replaced.) Used clear the printer mode print counter and the self print mode print counter. Used to clear the FAX counter. (Only when FAX is installed) Used to reset the OPC drum rotation time, and the DV unit rotation time counter. The developer counter in the DV unit installed is reset. Used to clear the counters related to the scan mode and the internet FAX mode. Used to check the operations of the developing section (toner concentration, humidity and toner concentration sensor, humidity sensor, temperature sensor output can be monitored.) Used to make the initial setting of toner concentration when replacing developer. Used to set the specifications of the auditor. Setting must be made according to the auditor use conditions. Used to set the count mode of the total counter and the maintenance counter. Used to set the specifications (paper, document detection, etc.) of the destination. Used to set the network scanner trial mode. Used to set YES/NO of toner save operation. (This function is valid only in Japan and UK versions. (Depends on the destination setting of SIM26-6.) For the other destinations, the same setting can be made by the user program P22.) Used to set the operation mode conforming to the CE mark (Europe safety standards). (Conforming to soft start when driving the fusing heater lamp.) Used to set whether the same continuous troubles are displayed as one trouble or the series of troubles with SIM 22-4 when the same troubles occur continuously. Used to set CONTINUE/STOP of printing when maintenance timing is over and the count value reaches 110% of replacement timing (life). Used to set the automatic magnification ratio selection (AMS) in the pamphlet mode. Black-White reverse YES/NO setting Used to set whether non-print paper (insertion paper, cover paper) (blank image print paper) is counted up or not. Used to set ENABLE/DISABLE of the CA key cancel function of print stop. Used to set the specifications for operations in case of communication trouble between the host computer and MODEM (machine side). (When communication trouble occurs between the host computer MODEM and the machine, the self diag display (U7-00) is printed and setting for inhibition of print or not is made.) Used to enter the machine tag No. (This function allows to check the tag No. of the machine with the host computer.) Used to check the operation of sensors and detectors in other than the paper feed section and the operations of the related circuits. Used to check the operation of sensors and detectors in the paper feed section and the related circuits.
Function (Purpose) Used to check the operation of the manual feed tray paper size detector and the related circuit. (The operation of the manual feed tray paper size detector can be monitored with the LCD display.) Used to adjust the manual paper feed tray paper width detector detection level. Used to enter the manual paper feed tray paper width adjustment value. Used to check the multi-purpose tray width detection adjustment value. Used to check the multi-purpose tray width detection adjustment value. Used to check the operation of the document size sensor and the related circuit. (The operation of the document size sensor can be monitored with the LCD display.) Used to adjust the document size sensor sensing level. Used to check the operation of the document size sensor and the related circuit. (The document size sensor output level can be monitored with the LCD display.) Used to set the fusing temperature in each operation mode. Used to set enable/disable of correction operations in the image forming (process) section. Used to check the data related to the image forming section correction (process correction) result (corrected main charger grid voltage, the developing bias voltage, and the laser power voltage in each print mode). (This simulation allows to check that correction is performed normally or not.) Used to check the output level of the temperature sensor and the humidity sensor. Used to check the toner concentration control data. Used to adjust the copy density in all the copy modes (Auto, Text, Text/Photo, and Photo mode). Used to adjust the print density for each density level (display value) in the copy mode (binary Text mode). An optional print density can be set for each density level (display value). Used to adjust the print density for each density level (display value) in the copy mode (binary Text/Photo mode). An optional print density can be set for each density level (display value). Used to adjust the print density for each density level (display value) in the copy mode (binary Photo mode). An optional print density can be set for each density level (display value). Used to adjust the print density in the FAX mode (all modes). Used to adjust the print density in the FAX mode (each normal mode). (Only when FAX is installed.) Used to adjust the print density in the FAX mode (each fine mode). (Only when FAX is installed.) Used to adjust the print density in the FAX mode (each super fine mode). (Only when FAX is installed.) Used to adjust the print density in the FAX mode (each ultra fine mode). (Only when FAX is installed.) Used to set the gain in shading correction.
2 7 11 12 41 1
15 25 1
2 26 3
2 3
5 6 10 18
43 44
1 1
30
35
14 16 46 2 9
38
41 50 52
10
68 27 1
11
12 13
14 15
30
16
17
manuals4you.com
Function (Purpose) Used to adjust the gamma (density gradient) in the copy mode. Used to set the auto mode operation specifications in each mode (copy, scan, FAX). Used to adjust the copy density correction in the SPF copy mode for the document table copy mode. The adjustment is made so that the copy density becomes the same as that of the document table copy mode. Used to adjust the scanner exposure level in all the scanner modes. Used to adjust the scanner exposure level in the normal text mode. Used to adjust the scanner exposure level in the fine text mode. Used to adjust the scanner exposure level (in the super fine text mode). Used to adjust the scanner exposure level in the ultra fine text mode. Used to adjust the gamma (density gradient) of the network scanner mode. Used to adjust sharpness of the copy mode. Used to adjust sharpness of the FAX mode. Used to adjust the image density in the FAX mode (600dpi). Used to adjust sharpness of the scanner mode. Used to adjust the copy magnification ratio (in the main scanning and the sub scanning directions). Used to adjust the copy magnification ratio in the sub scanning direction. HSYNC cycle adjustment Used to adjust the copy image position and the void area (image loss) adjustment on print paper in the copy mode. (The similar adjustment can be performed with SIM 50-5 and 50-2 (Simplified method).) (Document table mode) Used to adjust the document scan position, the image print position, and the void area (image loss). (Simple adjustment) (This adjustment is the simple method of SIM 50-1.) (Document table mode) Used to adjust the print image position and the void area (image loss) on print paper. (Adjustment as the print engine) (This adjustment is reflected on all the FAX/printer/copy modes.) Used to adjust the copy image position and void area (image loss) on print paper in the copy mode. (The similar adjustment can be performed with SIM 50-7 (simple method).) (SPF mode) Used to adjust the copy image position and void area (image loss) on print paper in the copy mode. (The similar adjustment can be performed with SIM 50-6.) (SPF mode) Used to adjust the print image off-center position. (Adjusted separately for each paper feed section.) Used to adjust the scan image off-center position. (Adjusted separately for each scan mode.) Used to adjust the image loss of the scan image in the FAX/scan mode. Used to adjust the contact pressure of paper on the resist roller of each section (each paper feed, duplex feed and SPF paper feed of the copier). (This adjustment is required when the print image position variations are considerably great or when paper jams occur frequently.)
Function (Purpose) Used to adjust the DSPF width detection level. Used to enter the SPF width detection adjustment value. Used to adjust the document scan start position. (Used to adjust the scanner scan position in the SPF mode front scan.) Used to set the specifications of the engine control operations. (PCU PWB) Used to set the specifications of the scanner control operations. (Scanner control PWB) Used to set the specifications of the controller operations. (MFP control PWB) Used to transfer the MFP controller data. (Used to repair the PWB.) Used to check the MFP control (DRAM) operations (read/write). Used to check the operation of the scanner (write) unit (LSU). Used to adjust the laser power (absolute value) in the copy mode. Used to adjust the laser power (absolute value) in the FAX mode. Used to adjust the laser power (absolute value) in the printer mode. Used to format the hard disk. (Only in the model with a disk installed) Used to check the operation of the hard disk (read/write). (Only in the model with a disk installed) (Partial check) Used to check the operation of the hard disk (read/write). (Only in the model with a disk installed) (All areas check) Used to check the operations of the hard disk. (The self diag operation of the SMART function is executed.) (Only in the model with a disk installed) Used to check the operations of the hard disk. (The result of the self diag operation of the SMART function is printed out.) (Only in the model with a disk installed) Used to format the hard disk (the system area excluded). (Only in the model with a disk installed) Used to delete a job complete list (also to delete job log data) (Only in the model with a disk installed) Used to delete document filing data. (The management area (standard folder, user folder) is cleared.) (Only in the model with a disk installed) Used to check the result of shading correction. (The shading correction data are displayed.) Used to execute shading. Used to adjust the white plate scan start position for shading. (Document table mode) Used to check the operation of the printer section (self-print operation), (The print pattern, the paper feed mode, the print mode, the print quantity, and the density can be optionally set.) Used to adjust the touch panel (LCD display section) detection position. Used to check the result of the touch panel (LCD display) detection position adjustment. (The coordinates are displayed.) Used to change and check the FAX soft switch functions. (Used to change and check the functions provided for the FAX soft switches.) (Only when FAX is installed)
55
1 2 3
21 22 23 24 25 27 31 39 45 46 1 5 6 1
56 60 61
1 1 1 2 3 4
62
1 2
48
50
10
11
63
1 2 7
10
64
12 27 51 2
65
1 2
66
Function (Purpose) Used to clear the FAX soft switch function data and to set to the default. (Excluding the adjustment values.) (Only when FAX is installed) Used to check the operation of the FAX PWB memory (read/write). (This adjustment is required when the PWB is replaced with a new one.) (Only when FAX is installed) Used to check the output operation of data signals in each data output mode of FAX. (Used to check the operation of MODEM. ) Send level: Max. (Only when FAX is installed) Used to check the output operation of data signals in each data output mode of FAX. (Used to check the operation of MODEM.) An output is sent at the send level set by the soft switch. (Only when FAX is installed) Used to print the confidential pass code. (Used when the confidential pass code is forgotten.) (Only when FAX is installed) Used to print the image memory data (memory send/receive). (Only when FAX is installed) Used to check the output operation of various sound signals of FAX. (Used to check the operation of the sound output IC.) Send level: Max. (Only when FAX is installed) Used to check the output operation of various sound signals of FAX. (Used to check the operation of the sound output IC.) An output is sent at the send level set by the soft switch. (Only when FAX is installed) Used to clear all data of the image memory (memory send/receive). The confidential data are also cleared at the same time. (Only when FAX is installed) Used to check the output operation of FAX G3 mode 300bps. (Used to check the operation of MODEM.) Send level: Max. (Only when FAX is installed) Used to check the output operation of FAX G3 mode 300bps. (Used to check the operation of MODEM.) An output is send at the send level set by the soft switch. (Only when FAX is installed) Used to enter (set) the number of FAX dial signal output test. (The dial number set by this simulation is outputted when the dial signal output test is made by SIM 66-14 - 16. ) (Only when FAX is installed) Used to set the make time in the FAX pulse dial mode (10pps) and to test the dial signal output. (The dial number signal set by SIM 66-13 is outputted.) Used to check troubles in dialing and to check the operation. (Only when FAX is installed) Used to set the make time in the FAX pulse dial mode (20pps) and to test the dial signal output. (The dial number signal set by SIM 66-13 is outputted.) Used to check troubles in dialing and to check the operation. (Only when FAX is installed) Used to check the dial signal (DTMF) output in the FAX tone dial mode. (The dial number signal set by SIM 66-13 is outputted.) The send level can be set to an optional level. Used to check troubles in dialing and to check the operation. (Only when FAX is installed)
Function (Purpose) Used to check the dial signal (DTMF) output in the FAX tone dial mode. Send level: Max. Used to check the operation. (Only when FAX is installed) Used to check the dial signal (DTMF) output in the FAX tone dial mode. An output is sent at the send level set by the soft switch. Used to check the operation. (Only when FAX is installed) Used to back-up the HDD data into the Flash memory (optional FAX expansion memory: ARMM9). (Only when FAX is installed) Used to read the back-up data by SIM 66-19 to the SRAM/HDD. (Only when FAX is installed) Used to print information related to FAX (various registrations, communication management, file management, system error protocol). (Only when FAX is installed) Used to adjust the handset volume. (Only when the FAX is installed.) Used to download the FAX program. (Only when FAX is installed) Not used in the market. (For development) Used to clear the FAST memory data. (Only when FAX is installed) Used to register the FAX number for Modem dialin. (Only when FAX is installed) Not used in the market. (For development) Used to register external telephone numbers for Modem dial-in. (Only when FAX is installed) Not used in the market. (For development) Used to register the transfer number for voice warp. (Only when FAX is installed) Not used in the market. (For development) Used to clear data related to an address book (one-touch registration, program registration/ expansion, relay memory box registration, each table content). Used to check the change in the TEL/LIU status. (Only when FAX is installed) Used to check the relay operation. (Only when FAX is installed) Used to check the receive data (fixed data) from the line. (Only when FAX is installed) Used to check the signal (BUSY TONE/CNG/ CED/FNET/DTMF) detection. (Only when FAX is installed) Used to measure the communication time of test image data. (Only when FAX is installed) Modem program rewriting. (Only when FAX is installed) Not used in the market. (For development) Used to check interface between MFPC controller and MDMC. (Check of the data line or the command line) (Only when FAX is installed) Used to set the destination specifications. (Only when FAX is installed) PIC program rewriting (Only when FAX is installed) PIC adjustment value writing (Only when FAX is installed) Used to check the operation of the parallel I/F of the printer. (This simulation is for production only, and requires a special tool for execution. Not used in the market.) Used to set YES/NO of the parallel I/F select signal of the printer. Used to check the operation of the network card.
18
19
20 21
22 23
7 8
24 25
26
10
27
29
11
30 31 32 33
12
13
14
34 35
36
15
39 42 43 67 2
16
11 16
manuals4you.com
C. Details
2
2-1 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operations of the automatic document feeder unit and the control circuit. DSPF Operation
1
1-1 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operations of the scanner (read) unit and its control circuit. Optical (Image scanning) Operation
Operation/Procedure 1) Select the operation mode with 10-key. 2) Press START key. The SPF repeat paper feed, transport, and paper exit at the speed corresponding to the operation mode. The operation can be stopped by [CUSTOM SETTINGS] key. 1 2 HIGH SPEED LOW SPEED High speed Low speed
Operation/Procedure 1) Select the operation mode with 10-key. 2) Press START key. The scanner performs scanning at the speed corresponding to the operation mode. 1 2 3 4 TOP SPEED HIGH SPEED MIDDLE SPEED LOW SPEED Top speed (220mm/s) High speed (168.7mm/s) Middle speed (110mm/s) Low speed (55mm/s)
SIMULATION 2-1 SPF AGING TEST. SELECT 1-2, AND PRESS START. 1. HIGH SPEED 2. LOW SPEED
SIMULATION 1-1 SCANNER CHECK. SELECT 1-4, AND PRESS START. 1. TOP SPEED 2. HIGH SPEED 3. MIDDLE SPEED 4. LOW SPEED
SIMULATION 2-1 SPF AGING TEST. EXECUTING. 1. HIGH SPEED 2. LOW SPEED
SIMULATION 1-1 SCANNER CHECK. EXECUTING. 1. TOP SPEED 2. HIGH SPEED 3. MIDDLE SPEED 4. LOW SPEED
2-2 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operations of the sensors and detectors in the automatic document feeder unit and the related circuits. DSPF Operation
1-2 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of sensor and detector in the scanning (read) section and the related circuit. Optical (Image scanning) Operation
Operation/Procedure The operating conditions of the sensors and detectors are displayed. The active sensors and detectors are highlighted. SPFSET SOCD SCOV SPED SPPD SPOD SWDn SPLSn CISSET STSET SWD_LEN SWD_AD SPF sensor Open/close sensor Paper feed cover sensor Document set sensor Resist front detection sensor Document paper exit sensor Document width sensor (n 1 (inside) - 6 (outside)) Document length sensor (n 1 (inside) - 2 (outside)) CIS installation detection Stamp unit installation sensor SPF guide plate position (unit: 0.1mm) SPF document width detection volume output AD value
Operation/Procedure The sensor and detector operation conditions are displayed. The active sensors and detectors are highlighted. The scanner (read) unit is in the home position.: "MHPS" section is highlighted. The scanner (read) unit is not in the home position.: "MHPS" is normally displayed. MHPS Optical system home position
SIMULATION 2-2 SPF SENSOR CHECK. SPFSET SOCD SPPD SPOD SWD4 SWD3 SPLS2 SPLS1 SWD_LEN: 2100
2-3 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operations of the loads in the automatic document feeder unit and the control circuits. DSPF Operation
Operation/Procedure 1) Select the number corresponding to the target of operation check with 10-key. 2) Press START key. The load selected in procedure 1 is operated. Press [CUSTOM SETTINGS] key to stop the operation of the load. 1 2 3 4 5 6 7 MOTOR(H) MOTOR(L) SDSS SPFS SPFC SRRC STMPS Motor high speed Motor low speed SPF gate solenoid SPF pick-up solenoid SPF paper feed clutch SPF resist roller clutch Stamp solenoid
STHP POD SCID PID T2PD T2DN T2UP JRHP JFHP SCID2 STTHP2 STTHP1 STUHP PSHP PPD DSW2 DSW1 24VM T1PF STSP STLS STNC DOPD MMLK SCPD FSSS FJS FFDSW FTCS FFDS FSPS FSUC FSS FSTHPS FSHPS FLE FLLLS FULS FFE FFES FFRHPS FFHPS FFPS FSLS FBES FOBHPS FAS FRJHPS FFJHPS FARHPS FPHPS FES
SIMULATION 2-3 SPF LOAD TEST. SELECT 1-7, AND PRESS START. 1.MOTOR(H) 2.MOTOR(L) 3.SDSS 4.SPFS 5.SPFC 6.SRRC 7.STMPS
SIMULATION 2-3 SPF LOAD TEST. EXECUTING. 1.MOTOR(H) 2.MOTOR(L) 3.SDSS 4.SPFS 5.SPFC 7.STMPS
6.SRRC
3
3-2 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of sensor and detector in the finisher and the related circuit. Finisher Operation
Built-in finisher Stapler HP detection Tray 2 paper exit detection Staple compiler paper entry detection Paper entry detection Tray 2 paper empty detection Tray 2 lower limit detection Tray 2 upper limit detection Jogger R HP Jogger (F) HP Staple compiler paper entry detection 2 Staple rotation HP detection 2 Staple rotation HP detection 1 Staple shift HP detection Pusher HP detection Paper hold return detection Staple replacement door open detection Compiler jam cancel door open detection 24V power supply Tray 1 full detection Stapling ready detection Cartridge inside spare staple empty detection Cartridge empty detection Interface unit door open detection Main drive motor lock detection Staple compiler paper empty detection Console finisher Stapler safety switch Joint switch Front door switch Upper cover sensor Front door sensor Self prime sensor Stapler connection detection Staple sensor Stapler HP sensor Slide HP sensor Lift lock sensor Lift lower limit sensor Lift upper limit sensor Bookbinding clock sensor Bookbinding paper sensor Bookbinding roller HP sensor Bookbinding HP sensor Bookbinding position sensor Paper surface sensor Tray paper sensor Paper exit belt HP sensor Alignment tray sensor Alignment HP sensor R Alignment HP sensor F Bundle roller HP sensor Paddle HP sensor Entry port sensor
The following units are added when the punch unit is installed to the console finisher: FPE FPSHPS FPUC FPDS FPDSS4 FPDSS3 FPDSS2 FPDSS1 FPTS Punch motor encoder Punch side register HP Punch connection detection Punch dust sensor Punch side register sensor 4 Punch side register sensor 3 Punch side register sensor 2 Punch side register sensor 1 Punch timing sensor
Operation/Procedure The operating conditions of the sensors and detectors are displayed. The active sensors and detectors are highlighted.
manuals4you.com
(Built-in finisher)
SIMULATION 3-3 FINISHER SENSOR CHECK. PID SCID SCPD POD T2DN T2PD STNC STHP PSHP STUHP STTHP2 DOPD 24VM MMLK SIMULATION 3-3 FINISHER LOAD TEST. SELECT 1SCID2 T1PF STSP JFHP STTHP1 DSW1 PPD T2UP STLS JRHP DSW2 SIMULATION 3-3 FINISHER LOAD TEST. EXECUTING AND PRESS START.
2
Press [START] key, and the operation is started. Press [CUSTOM SETTINGS] key, and the operation is stopped.
(Console finisher)
SIMULATION 3-2 FINISHER SENSOR CHECK. FSSS FJS FFDSW FTCS FFDS FSPS FSUC FSS FSTHPS FSHPS FLE FLLLS FULS FFE FFES FFRHPS FFHPS FFPS FSLS FBES FOBHPS FAS FRJHPS FFJHPS FARHPS FPHPS FES (FPE)(FPSHPS)(FPUC)(FPDS)(FPDSS4)(FPDSS3)(FPDSS2) (FPDSS1)(FPTS)
2
3-6 Purpose Function (Purpose) Adjustment Used to adjust the stacking capacity of the finisher. (Used to adjust the alignment plate (jogger) stop position in the finisher paper width direction. The adjustment is made by changing the alignment plate home position in the paper width direction by software.) Finisher Operation
( ) : Added when the punch unit is installed. 3-3 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of the load in the finisher and the control circuit. Finisher Operation
Section Item
Operation/Procedure Enter the adjustment value with 10 digit key pad and press START key. The jogger moves to LT position (Inch series) or A4 position (AB series) according to the entered value, and stops there.
SIMULATION 3-6 FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.
Operation/Procedure 1) Select the number corresponding to the target of operation check with 10-key. 2) Press START key. The load selected in procedure 1 is operated. Press [CUSTOM SETTINGS] key to stop the operation of the load. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 T2S T2OM SPS SCRS PPS SCGS STTM STUM MM EVM STM JRM JFM PSM FFC FPSM FPNM FLM FFSM FSM FRJM FFJM FAM FPM FFM Built-in finisher Tray 2 solenoid Paper exit motor Stopper solenoid Roller pressure release solenoid Rear edge h folding solenoid Compiler gate solenoid Staple rotation motor Stapler shift motor Main drive motor Elevator motor Staple motor Jogger motor rear Jogger motor front Pusher motor Console finisher Folding clutch Puncher side register motor Punch motor Shift motor Stapler motor Slide motor Alignment motor R Alignment motor F Bundle exit motor Paddle motor Transport motor
Press [START] key, and the operation is started.
50
Press [CUSTOM SETTINGS] key, and the operation is stopped. Stops when the operation is terminated.
50
3-10 Purpose Function (Purpose) Section Item Adjustment Console finisher (AR-FN7) adjustment Finisher Operation
Operation/Procedure 1) Select the number corresponding to the target of operation check with 10-key. 2) Press [START] key. 3) Enter the adjustment value with 10-key. 4) Press [START] key. (The entered value is stored.) Item 1 Saddle binding position adjustment 2 Saddle folding position adjustment 3 Front alignment position adjustment 4 Rear alignment position adjustment Set Initial 1STEP range value 0 - 400 200 0.0707mm 0 - 400 0 - 20 0 - 20 200 10 10 0.0525mm 0.367mm 0.367mm
Item
5 Staple rear one-position binding position adjustment 6 Staple front one-position 0 - 200 binding position adjustment 7 Staple 2-position binding 0 - 200 center adjustment 8 Staple 2-position binding pitch 0 - 99 adjustment 9 Punch center adjustment 47 - 53 (Slide direction) 10 Punch hole position 0 - 99 adjustment (Paper feed direction)
SIMULATION 3-10 CONSOLE FINISHER SETTING. 1.SADDLE POSITION 3.FRONT ADJUST 4.REAR ADJUST 6.STAPLE FRONT 8.STAPLE PITCH 10.PUNCH HOLE
Set Initial 1STEP range value 0 - 200 100 0.04374mm 100 100 50 50 50 0.04374mm 0.04374mm 0.04374mm 1mm 0.105mm
3-21 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operations of the mail bin stacker loads. Mail bin stacker Operation
Operation/Procedure 1) Select the number corresponding to the target of operation check with 10-key. 2) Press [START] key. The load selected in procedure 1 is operated. Press [CUSTOM SETTINGS] key to stop the operation of the load. 1 2 3 4 5 6 7 8 MM GSOL1 GSOL2 GSOL3 GSOL4 GSOL5 GSOL6 GSOL7 Main motor Gate solenoid 1 Gate solenoid 2 Gate solenoid 3 Gate solenoid 4 Gate solenoid 5 Gate solenoid 6 Gate solenoid 7
SELECT 1-10,AND PRESS START. 2.FOLDING POSITION 5.STAPLE REAR 7.STAPLE BOTH 9.PUNCH CENTER
SIMULATION 3-10 CONSOLE FINISHER SETTING. INPUT VALUE, AND PRESS START. 1.FOLDING POSITION
200
SIMULATION 3-21 MAIL BOX LOAD TEST. SELECT 1-8 AND PRESS START. 1.MM 2.GSOL1 3.GSOL2 4.GSOL3 5.GSOL4 6.GSOL5 7.GSOL6 8.GSOL7
Press [START] key, and the operation is started.
3-20 Purpose Function (Purpose) Section Item Operation test/Check Used to check the mail bin stacker sensor. Mail bin stacker Operation
Operation/Procedure The operating conditions of the sensors and detectors are displayed. The active sensors and detectors are highlighted. MPFD1 MPFD2 MPFD3 MPFD4 MPFD5 MPFD6 MPFD7 MPFD8 MPID MPPD1 MPPD2 MPPD3 MPPD4 MPPD5 M24VM MDD1 MDOPD Tray 1 paper full detection Tray 2 paper full detection Tray 3 paper full detection Tray 4 paper full detection Tray 5 paper full detection Tray 6 paper full detection Tray 7 paper full detection Tray 8 paper full detection Interface unit paper entry detection Paper transport sensor 1 Paper transport sensor 2 Paper transport sensor 3 Paper transport sensor 4 Paper transport sensor 5 24V power supply Jam cancel door Interface unit door
SIMULATION 3-21 MAIL BOX LOAD TEST. EXECUTING.... 1.MM 2.GSOL1 3.GSOL2 4.GSOL3 5.GSOL4 6.GSOL5 7.GSOL6 8.GSOL7
4
4-2 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operations of the sensors and detectors in the paper feed section (desk paper feed/large capacity tray) and the related circuit. Paper feed Operation
Operation/Procedure The operating conditions of the sensors and detectors are displayed. The active sensors and detectors are highlighted.
SIMULATION 3-20 MAIL BOX SENSOR CHECK. MPFD1 MPFD2 MPFD3 MPFD4 MPFD8 MPID MPPD1 MPPD2 M24VM MDD1 MDOPD
MPFD5 MPPD3
MPFD6 MPPD4
MPFD7 MPPD5
manuals4you.com
<Desk> DDRS DSPD2 DSPD1 DCSS24 DCSS23 DCSS22 DCSS21 DLUD2 DPED2 DPFD3 DCSS14 DCSS13 DCSS12 DCSS11 DLUD1 DPED1 DPFD2 MCSS4 MCSS3 MCSS2 MCSS1 MCSPD MCLUD MCPED DPFD1 Desk door sensor Desk cassette 2 remaining paper quantity sensor Desk cassette 1 remaining paper quantity sensor Desk cassette 2 paper rear edge sensor 4 Desk cassette 2 paper rear edge sensor 3 Desk cassette 2 paper rear edge sensor 2 Desk cassette 2 paper rear edge sensor 1 Desk cassette 2 upper limit sensor Desk cassette 2 paper sensor Desk paper transport sensor 3 Desk cassette 1 paper rear edge sensor 4 Desk cassette 1 paper rear edge sensor 3 Desk cassette 1 paper rear edge sensor 2 Desk cassette 1 paper rear edge sensor 1 Desk cassette 1 upper limit sensor Desk cassette 1 paper sensor Desk paper transport sensor 2 MP tray size detection 4 MP tray size detection 3 MP tray size detection 2 MP tray size detection 1 MP tray remaining quantity detection MP tray upper limit detection MP tray paper empty detection MP tray transport detection
4-3 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operations of the loads in the paper feed section (desk paper feed/large capacity tray) and the related circuit. Paper feed Operation
Operation/Procedure 1. Select the number corresponding to the target of operation check with 10-key. 2. Press [START] key. The load selected in procedure 1 is operated. Press [CUSTOM SETTINGS] key to stop the operation of the load. <Desk> 1 2 3 4 5 6 7 8 <LCC> 1 2 3 4 5 6 7 8 TLUM2 TLUM1 MCLUM TPFCL TPCL2 TPCL1 MCPCL TMM LCC lift-up motor 2 LCC lift-up motor 1 LCC multi lift-up motor LCC transport clutch LCC paper feed clutch 2 LCC paper feed clutch 1 LCC multi paper feed clutch LCC transport motor DLUM2 DLUM1 MCLUM DPFCL DPCL2 DPCL1 MCPCL DMM Desk lift-up motor 2 Desk lift-up motor 1 Desk multi lift-up motor Desk paper transport clutch Desk paper feed clutch 2 Desk paper feed clutch 1 Desk multi paper feed clutch Desk transport motor
SIMULATION 4-2 DESK SENSOR CHECK. DDRS DPFD1 MCLUD DLUD1 DSPD1 DSPD2 DPED2 MCSS1 MCSS4 DCSS11 DCSS14 DCSS23 DCSS24
<LCC> TDRS TTSD TLUD2 TLUD1 TSPD2 TSPD1 TPED2 TPED1 TPFD3 TPFD2 MCSS4 MCSS3 MCSS2 MCSS1 MCSPD MCLUD MCPED TPFD1 Tandem side door sensor Tandem tray sensor Tandem tray 2 upper limit sensor Tandem tray 1 upper limit sensor Tandem tray 2 remaining quantity sensor Tandem tray 1 remaining quantity sensor Tandem tray 2 paper sensor Tandem tray 1 paper sensors Tandem paper transport sensor 3 Tandem paper transport sensor 2 MP tray size detection 4 MP tray size detection 3 MP tray size detection 23 MP tray size detection 1 MP tray remaining quantity detection MP tray upper limit detection MP tray paper empty detection MP tray transport detection
SIMULATION 4-2 LCC SENSOR CHECK. TDRS TTSD TPFD3 MCLUD MCSPD TSPD1 TPED1 TPED2 MCSS3 MCSS4
u an
yo 4 ls
o u.c
5
5-1 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of the display, LCD in the operation panel, and control circuit. Operation (Display/Operation key) Operation
5-3 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of the scanner lamp and the control circuit. Optical (Image scanning) Operation
Operation/Procedure 1) Select the number corresponding to the target of operation check with 10-key. 2) Press [START] key. The load selected in procedure 1 turns ON for 10sec. Press [CUSTOM SETTINGS] key to stop the operation. The copy lamp or CIS is turned on for 10sec and turned off. NOTE: CIS: only when the DSPF is installed.
SIMULATION 5-3 COPY LAMP TEST. SELECT 1-2, AND PRESS START. 1.COPY LAMP 2.CIS
Operation/Procedure The LCD is changed as shown below. (The contrast changes every 2sec from the current level to MAX MIN the current level. During this period, each LED is lighted.
SIMULATION 5-1
After 6.0sec
SIMULATION 5-1
Press [CUSTOM SETTINGS] key, and the operation is stopped after 10sec.
5-2 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of the heater lamp and the control circuit. Fixing (Fusing) Operation
Operation/Procedure 1) Select the number corresponding to the target of operation check with 10-key. 2) Press [START] key. The load selected in procedure 1 performs ON/OFF operation. Press [CUSTOM SETTINGS] key to stop the operation of the load. The ON/OFF operation of the selected heater lamp is repeated every 500ms five times. 1 2 HL1 (LOWER) HL2 (UPPER) Heater lamp 1 (Lower) Heater lamp 2 (Upper)
6
6-1 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of the paper transport system loads and the control circuit. Paper transport (Discharge/Switchback/Transport) Operation
Operation/Procedure 1) Select the number corresponding to the target of operation check with 10-key. 2) Press [START] key. The load selected in procedure 1 operates. Press [CUSTOM SETTINGS] key to stop the operation. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15*1 16*1 17*1 MSWPR HLPR DCPR MM DM POM_FW POM_RV CPFC RRC TRC FGS_FIN LUM TRC_DSK PSPS MCM MCPCL MCFCL MSW power relay signal Heater power relay DC power relay Main motor Drum motor Paper exit motor forward rotation Paper exit motor reverse rotation Paper feed clutch Resist roller clutch Transport roller clutch Finisher gate solenoid Tray 1 lift-up motor Desk clutch sync signal Separation pawl solenoid MP drive motor control signal MP tray paper feed clutch signal MP tray transport clutch signal
SIMULATION 5-2 HEATER LAMP TEST. SELECT 1-2, AND PRESS START. 1.HL1(LOWER) 2.HL2(UPPER)
Press [CUSTOM SETTINGS] key, and the operation is stopped. The operation is repeated the specified number of times before stopping.
manuals4you.com
MP tray lift-up motor signal Manual paper feed solenoid signal Manual paper feed clutch signal Manual paper feed gate solenoid
7
7-1 Purpose Function (Purpose) Section Item Setting Used to set the operating conditions of aging.
*1: Displayed when OPTION of multi-purpose only. *2: Displayed when manual feed OPTION is added.
SIMULATION 6-1 FEED OUTPUT CHECK. SELECT 1-22, AND PRESS START. 1.MSWPR 2.HLPR 3.DCPR 4.MM 5.DM 6.DSB_FW 7.DSB_RV 8.CPFC 9.RRC 10.TRC 11.FGS_FIN 12.LUM 13.TRC_DSK 14.PSPS 15.MCM 16.MCPCL 17.MCFCL 18.MCLUM 19.MPFS 20. MPFC 21.MSS 22.MSWS
Operation
Operation/Procedure 1) Select the number corresponding to the operating condition of aging with 10-key. The combined mode of 0 - 6 mode and 10, 20, or 30 mode can be set. In that case, the number corresponding to one of 0 - 6 mode and the number corresponding to one of 10, 10, and 30 mode are added and the sum number is entered. 2) Press [START] key. The condition selected in procedure 1) is set. The setting of this simulation is kept valid until the power is turned off.
Press [CUSTOM SETTINGS] key, and the operation is stopped immediately or after repeating the operation several times.
SIMULATION 6-1 FEED OUTPUT CHECK. EXECUTING.... 1.MSWPR 2.HLPR 3.DCPR 4.MM 5.DM 6.DSB_FW 7.DSB_RV 8.CPFC 9.RRC 10.TRC 11.FGS_FIN 12.LUM 13.TRC_DSK 14.PSPS 15.MCM 16.MCPCL 17.MCFCL 18.MCLUM 19.MPFS 20.MPFC 21.MSS 22.MSWS
6-2 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operations of each fan motor and its control circuit. Other Operation
Operation/Procedure 1) Select the number corresponding to the target of operation check with 10-key. 2) Press [START] key. The load selected in procedure 1 operates. Press [CUSTOM SETTINGS] key to stop the operation. 1 2 3 Fan motor high speed Fan motor low speed Cooling fan motor (Controller/HDD)
NO MISS FEED DETECTION AGING AGING/NO MISS FEED DETECTION. 3 AGING/NO MISS FEED DETECTION/NO WARM UP/ NO TEMPERATURE CONTROL. 4 NO WARM UP. 5 AGING/INTERVAL. 6 AGING/INTERVAL/NO MISS FEED DETECTION. +10 NO PROCESS UNIT CHECK.
0 1 2
No jam detection Aging mode No jam detection, aging mode No jam detection/ no warmup/ no fusing temperature control, aging mode
No warm-up Intermittent aging mode No jam detection intermittent aging mode Above +10: No process unit (including the developing unit) detection +20 NO SHADING. Above +20: No shading +30 NO PROCESS UNIT CHECK/ Above +30: No process unit NO SHADING. detection /no shading
SIMULATION 7-1 AGING TEST SETTING. SELECT 0-36, AND PRESS START. 0.NO MISS FEED DETECTION 1.AGING 2.AGING/NO MISS FEED DETECTION. 3.AGING/NO MISS FEED DETECTION/ NO WARM UP/NO TEMPERATURE CONTROL. 4.NO WARM UP. 5.AGING/INTERVAL. 6.AGING/INTERVAL/NO MISS FEED DETECTION. +10:NO PROCESS UNIT CHECK. +20:NO SHADING. +30:NO PROCESS UNIT CHECK/NO SHADING.
SIMULATION 6-2 FAN MOTOR CHECK. SELECT 1-3, AND PRESS START. 1.FMHi 2.FMLo 3.CFM-ICU/HDD
Press [START] key to start registration and operation. The operation mode is kept until the power is turned off or setting is made again.
7-6 Purpose Function (Purpose) Section Item Setting Used to set the intermittent aging cycle.
8
8-1 Purpose Function (Purpose) Section Adjustment/Operation test/Check Used to check and adjust the operations of the developing voltage of each color and the control circuit. Image process (Photoconductor/Developing/ Transfer/Cleaning)
Operation
Operation/Procedure 1) Enter the intermittent aging cycle (unit: sec) with 10-key. 2) Press [START] key. The time entered in procedure 1) is set. Set range of interval time: 1 - 999 (sec) Set the intermittent aging mode cycle of 7-1 with 10-key. (Unit: sec)
SIMULATION 7-6 INTERVAL AGING CYCLE SETUP. INPUT TIME AND PRESS START. (1-999, UNIT: sec)
Operation/Procedure 1) Enter the number corresponding to the adjustment item with 10-key. 2) Press [START] key. 3) Enter the adjustment value with 10-key. 4) Press [START] key. (The set value is stored, and the output corresponding to the set value is outputted for 30sec.) Press [CUSTOM SETTINGS] key to stop the operation. (The developing bias output voltage adjustment and output check can be made in each print mode.)
10
7-8 Purpose Function (Purpose) Item Setting Used to set the warm-up time display YES/NO. Operation
Operation/Procedure 1) Select the number corresponding to the warm-up time display YES/NO. 2) Press [START] key, and the number selected in procedure 1) is set. The setting of this simulation is kept valid until the power is turned off. The warm-up time is displayed in the unit of second.
SIMULATION 7-8 WARM UP TIME DISPLAY. ARE YOU SURE? 1. YES 2. NO
Auto mode Text mode Text/Photo mode Photo mode Printer mode FAX mode Reverse 0 - 255 developing bias voltage
Default ARARM351U/ M451U/ M355U M455U 0 - 745 455 485 485 485 Set range
150
150
1
Press [CUSTOME SETTING] key, and time count is stopped.
SIMULATION 8-1 DV BIAS SETTING. SELECT 1-7, AND PRESS START. 1.AUTO 485 2.CHARACTER 485 3.MIX 485 4.PHOTO 485 5.PRINTER 485 6.FAX 485 7.PLUS 150
SIMULATION 8-1 DV BIAS SETTING. INPUT VALUE, AND PRESS START. 1:AUTO (0-745)
30
Warm-up is completed. Press [CUSTOM SETTINGS] key. Press [START] key.
485
60
485
manuals4you.com
8-2 Purpose Function (Purpose) Section Adjustment/Operation test/Check Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit. Image process (Photoconductor/Developing/ Transfer/Cleaning)
4) Press [START] key. (The set value is stored, and the voltage corresponding to the set value is outputted for 30sec.) Press [CUSTOM SETTINGS] key to stop the operation. (The transfer output voltage adjustment and output check can be made in each print mode.) Item 1 FRONT 2 BACK Long side print mode Back side print mode Default AR-M351U/ AR-M451U/ M355U M455U 0 - 620 220 267 Set range 267 310
Operation/Procedure 1) Enter the number corresponding to the adjustment item with 10-key. 2) Press [START] key. 3) Enter the adjustment value with 10-key. 4) Press [START] key. (The set value is stored, and the output corresponding to the set value is outputted for 30sec.) Press [CUSTOM SETTINGS] key to stop the operation. (The main charger grid output voltage adjustment and output check can be made in each print mode.) Default ARARM351U/ M451U/ M355U M455U 200 - 900 615 645 645 645 Set range
SIMULATION 8-6 THV+ SETTING. SELECT 1-2, AND PRESS START. 1.FRONT 267 2.BACK 310
Item 1 2 3 4 5 6 AUTO CHARACTER MIX PHOTO PRINTER FAX Auto mode Text mode Text/Photo mode Photo mode Printer mode FAX mode
SIMULATION 8-6 THV+ SETTING. INPUT VALUE, AND PRESS START. 1.FRONT(0-620)
267
SIMULATION 8-2 MAIN GRID SETTING. SELECT 1-6, AND PRESS START. 1.AUTO 645 2.CHARACTER 645 3.MIX 645 4.PHOTO 645 5.PRINTER 645 6.FAX 645
267
8-17 Purpose Function (Purpose) Section Item Operation test/Check Used to check and adjust the operation of the transfer voltage and the related circuit. (Transfer belt cleaning mode) Image process (Photoconductor/Developing/ Transfer/Cleaning) Operation
SIMULATION 8-2 MAIN GRID SETTING. INPUT VALUE, AND PRESS START. 1.AUTO (200-900)
645
Press [START] key. Press [CUSTOM SETTINGS] key. Or after 30sec output.
Operation/Procedure 1) Enter the number corresponding to the adjustment item with 10-key. 2) Press [START] key. 3) Enter the adjustment value with 10-key.
645
4) Press [START] key. (The set value is stored, and the voltage corresponding to the set value is outputted for 30sec.) Press [CUSTOM SETTINGS] key to stop the operation. (The transfer output voltage adjustment and output check can be made in the transfer belt cleaning mode.) Default ARARM351U/ M451U/ M355U M455U 0 - 240 120 160 0 - 240 120 160 0 - 1250 780 780 Set range
8-6 Purpose Function (Purpose) Section Adjustment/Operation test/Check Used to check and adjust the operation of the transfer voltage and the control circuit. Image process (Photoconductor/Developing/ Transfer/Cleaning)/Transfer
Operation/Procedure 1) Enter the number corresponding to the adjustment item with 10-key. 2) Press [START] key. 3) Enter the adjustment value with 10-key.
9-2
SIMULATION 8-17 TRANSFER ROLLER SETTING. SELECT 1-3, AND PRESS START. 1.SHV FRONT 160 2.SHV BACK 160 3.THV- 780
Operation test/Check Used to check the operations of the sensors and detectors in the duplex section and its control circuit. Duplex Operation
Operation/Procedure
SIMULATION 8-17 TRANSFER ROLLER SETTING. INPUT VALUE, AND PRESS START. 1.FRONT (0-240)
The operating conditions of the sensors and detectors are displayed. The active sensors and detectors are highlighted. ADUSET DSW_D AINPD APOD APPD1 APPD2 ADU installation detection ADU cabinet open detection ADU paper entry detection ADU paper exit detection ADU paper detection 1 ADU paper detection 2
160
Press [START] key. Press [CUSTOM SETTINGS] key. Or after 30sec output.
160
APOD
APPD1
APPD2
9
9-1 Purpose Function (Purpose) Section Item Operation test/Check Used to check and adjust the operation of the load (clutch/solenoid) in the duplex section and the control circuit. Duplex Operation
10
10-1 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operations of the toner motor and the related circuit. Process (Developing) Operation
Operation/Procedure 1) Select the number corresponding to the target of the operation check with 10-key. 2) Press [START] key. The load selected in procedure 1) is operated for 10sec. Press [CUSTOM SETTINGS] key to stop the operation. NOTE: Never execute this simulation with toner in the toner hopper. If executed, excessive toner will enter the developing section. Be sure to remove the toner motor from the toner hopper before execution. 1 2 Toner motor rotation start Cancel (The display returns to the main code entry menu.)
SIMULATION 10-1 TONER MOTOR ACTIVATION. ARE YOU SURE? 1.YES 2.NO
Operation/Procedure 1) Select the number corresponding to the target of the operation check with 10-key. 2) Press [START] key. The load selected in procedure 1) is operated. Press [CUSTOM SETTINGS] key to stop the operation. 1 2 3 ADMEN1 ADMEN2 DGS ADU motor 1 control signal ADU motor 2 control signal ADU gate solenoid
SIMULATION 9-1 ADU OUTPUT CHECK. SELECT 1-3, AND PRESS START. 1.ADMEN1 2.ADMEN2 3.DGS
2
Press [CUSTOM SETTINGS] key to stop the operations. Or after 10sec.
manuals4you.com
13
13-0 Purpose Function (Purpose) Section Item Clear/Cancel (Trouble etc.) Used to cancel the self-diag "U1" trouble. (Only when FAX is installed.) FAX Trouble
15
15-0 Purpose Function (Purpose) Section Item Clear/Cancel (Trouble etc.) Used to cancel the self-diag "U6-01, 02, 03, F312, 22" (large capacity paper feed tray, paper feed trays 1, 2) troubles. LCC Trouble
Operation/Procedure 1) Select 1 (YES) with 10-key. 2) Press [START] key. (The trouble display is canceled.) 1 2 YES NO After canceling U1 trouble, the machine returns to the main code entry standby mode. Without canceling U1 trouble, the machine returns to the main code entry standby mode.
Operation/Procedure 1) Select 1 (YES) with 10-key. 2) Press [START] key. (The trouble display is canceled.) 1 2 YES NO After canceling the LCC trouble, the machine returns to the main code entry standby mode. Without canceling the trouble, the machine returns to the main code entry standby mode.
14
14-0 Purpose Function (Purpose) Item Clear/Cancel (Trouble etc.) Used to cancel excluding the self-diag U1/LCC/ U2/PF troubles. Trouble Error
16
16-0 Purpose Function (Purpose) Section Item Clear/Cancel (Trouble etc.) Used to cancel the self-diag U2 troubles. MFP control PWB, PCU PWB, scanner control PWB Trouble
Operation/Procedure 1) Select 1 (YES) with 10-key. 2) Press [START] key. (The trouble display is canceled.) 1 YES After canceling the trouble other than U1, U2, PF, and LCC, the machine returns to the main code entry standby mode. Without canceling the trouble, the machine returns to the main code entry standby mode.
Operation/Procedure 1) Select 1 (YES) with 10-key. 2) Press [START] key. (The trouble display is canceled.) 1 2 YES NO After canceling the U2 trouble, the machine returns to the main code entry standby mode. Without canceling the trouble, the machine returns to the main code entry standby mode.
NO
17
17-0 Purpose Function (Purpose) Section Item Clear/Cancel (Trouble etc.) Used to cancel the PF troubles (when the copy inhibit command from the host computer is received). Communication unit (TEL/LIU/MODEM etc.) Trouble Error
22
22-1 Purpose Function (Purpose) Item Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the print count value in each section and each operation mode. (Used to check the maintenance timing.) Counter
Operation/Procedure 1) Select 1 (YES) with 10-key. 2) Press [START] key. (The trouble display is canceled.) 1 2 YES NO After canceling the PF trouble, the machine returns to the main code entry standby mode. Without canceling the trouble, the machine returns to the main code entry standby mode.
Operation/Procedure Various print counter values are displayed. TOTAL DRUM TONER DEVE MAINTENANCE TOTAL OUTPUT COPIES PRINTER FAX I-FAX OUTPUT DOC FILING OUTPUT RIIGHT SIDE OUTPUT OTHERS Total counter Drum counter Toner counter Developer counter Maintenance counter Total output quantity Copy effective paper counter Printer counter FAX print counter iFAX print counter Document filing print counter Right paper exit counter Other print counter (List print , etc.)
21
21-1 Purpose Function (Purpose) Item Setting Used to set the maintenance cycle. Specifications Counter
SIMULATION 22-1 COUNTER DATA DISPLAY. TOTAL: ******** DRUM: ******** TONER: ******** DEVE: ******** MAINTENANCE: ******** TOTAL OUTPUT: ******** COPIES: ******** PRINTER: ******** FAX OUTPUT: ******** I-FAX OUTPUT:******** DOC FILING OUTPUT:******** RIGHT SIDE:******** OTHERS: ********
Operation/Procedure 1) Enter the number corresponding to the maintenance timing display. 2) Press [START] key. The condition entered in procedure 1) is set. 0 1 - 200 999 Maintenance timing display Default (Differs depending on the model.) Maintenance display at 1K - 200K No maintenance display Set range 0 - 999 22-2 Purpose Function (Purpose) Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the total numbers of misfeed and troubles. (When the number of misfeed is considerably great, it is judged as necessary for repair. The misfeed rate is obtained by dividing this count value with the total counter value.) Trouble
Item
SIMULATION 21-1 MAINTENANCE CYCLE SETUP. INPUT VALUE 0-999, AND PRESS START. 0: DEFAULT 1-200: MAINTENANCE CYCLE (1K-200K) 999: FREE
Operation/Procedure The paper jam/trouble counter value is displayed. PAPER JAM SPF JAM TROUBLE Number of paper jams Number of SPF jams Number of troubles
SIMULATION 22-2 JAM/TROUBLE COUNTER DATA DISPLAY. PAPER JAM: ******** SPF JAM: ******** TROUBLE: ********
manuals4you.com
22-3 Purpose Function (Purpose) Adjustment/Setup/Operation data output/Check (Display/Print) Used to check misfeed positions and the misfeed count of each position. (If the misfeed count is considerably great, it may be judged as necessary to repair.) Sections other than SPF/DSPF section Trouble Misfeed
Section Item
Operation/Procedure The history of paper jams and misfeed is displayed. The misfeed history is displayed sequentially from the latest one. The max. 100 items of misfeed history can be recorded. The data may be used to identify trouble position. The latest 100 items of paper jam history are displayed. (Refer to the jam cause code table below.) (Jam cause code) Code NO_JAM_CAUSE TRAY2 Description No jam. Also used to cancel a jam. Tray 2 paper feed jam (MCPPD not-reaching: When AR-MU1 installed) (TPFD1 not-reaching: When AR-D13 installed) (DPFD1 not-reaching: When AR-D14 installed) DPFD1 not-reaching jam (Desk tray 1 feed paper) DPFD1 not-reaching jam (Desk tray 2 feed paper) TPFD1 not-reaching jam (Tandem desk feed paper) MCPPD remaining jam (Machine tray 2 feed paper: When AR-MU1 installed) TPFD1 not-reaching jam (Machine tray 2 feed paper: When AR-D13 installed) TPFD1 not-reaching jam (Machine tray 2 feed paper: When AR-D13 installed) DPFD1 remaining jam (Desk tray 1 feed paper) DPFD1 remaining jam (Desk tray 2 feed paper) TPFD1 remaining jam (Tandem desk feed paper) PPD1 not-reaching jam (Manual feed tray paper) Tray 1 feed paper jam (PPD1 not-reaching) PPD1 not-reaching jam (Machine tray 2 feed paper) PPD1 not-reaching jam (Desk tray 1 feed paper) PPD1 not-reaching jam (Desk tray 2 feed paper) PPD1 not-reaching jam (Tandem desk feed paper) PPD1 not-reaching jam (ADU refeed paper) PPD1 remaining jam (Manual feed tray feed paper) PPD1 remaining jam (Machine tray 1 feed paper) PPD1 remaining jam (Machine tray 2 feed paper) PPD1 remaining jam (Desk tray 1 feed paper)
PPD1PRI POD1N POD1S POD2N POD2SR POD2SL AINPDN AINPDS APODN APODS APPD1N APPD1S APPD2N APPD2S BPT APPD2SM DESK2 DPFD3SD2 DESK1 DPFD2N2 DPFD2S1 DPFD2S2 TTRAY2 TPFD3S2 TTRAY1 TPFD2N2 TPFD2S1 TPFD2S2 PPD1_DESK
DPFD1_ND1 DPFD1_ND2 TPFD1_NTD MCPPD_ST2 TPFD1_ST2 DPFD1_ST2 DPFD1_SD1 DPFD1_SD2 TPFD1_STD PPD1NMF TRAY1 PPD1NT2 PPD1ND1 PPD1ND2 PPD1NTD PPD1NAD PPD1SMF PPD1ST1 PPD1ST2 PPD1SD1
Description PPD1 remaining jam (Desk tray 2 feed paper) PPD1 remaining jam (Tandem desk feed paper) PPD1 remaining jam (ADU refeed paper) PPD1 remaining jam (Timer end of fusing ready standby/high voltage rising completion standby, etc.) PPD1 jam (Image ready is not supplied from ICU.) POD1 not-reaching jam POD1 remaining jam POD2 not-reaching jam POD2 remaining jam (When discharging to the right side of machine.) POD2 remaining jam (When discharging to the left side of machine.) ADU paper entry sensor not-reaching jam ADU paper entry sensor remaining jam ADU paper exit sensor not-reaching jam ADU paper exit sensor remaining jam ADU transport sensor 1 not-reaching jam ADU transport sensor 1 remaining jam ADU transport sensor 2 not-reaching jam (When ADU transport) ADU transport sensor 2 remaining jam (When ADU transport) Manual feed tray paper feed jam (APPD2 not-reaching) ADU transport sensor 2 remaining jam (Manual feed tray feed paper) Desk tray 2 paper feed jam (DPFD3 not activated) DPFD3 remaining jam (Desk tray 2 feed paper) Desk tray 1 paper feed jam (DPFD2 not activated) DPFD2 not-reaching jam (Desk tray 2 feed paper) DPFD2 remaining jam (Desk tray 1 feed paper) DPFD2 remaining jam (Desk tray 2 feed paper) Tandem tray 2 paper feed jam (TPFD3 not activated) TPFD3 remaining jam (Tandem tray 2 feed paper) Tandem tray 1 paper feed jam (TPFD2 not activated) TPFD2 not-reaching jam (Tandem tray 2 feed paper) TPFD2 remaining jam (Tandem tray 1 feed paper) TPFD2 remaining jam (Tandem tray 2 feed paper) DESK paper feed jam (Preliminary paper feed from the desk, no response in a certain time after paper feed instruction) Built-in finisher PID not-reaching jam Built-in finisher PID remaining jam Built-in finisher SCID not-reaching jam Built-in finisher SCID remaining jam Built-in finisher SCID2 not-reaching jam Built-in finisher SCID2 remaining jam Built-in finisher PPD remaining jam
PID_N PID_S MPPD1_N MPPD1_S MPPD2_N MPPD2_S MPPD3_N MPPD3_S MPPD4_N MPPD4_S MPPD5_N MPPD5_S
Description Built-in finisher SCPD not-reaching jam Built-in finisher SCPD remaining jam Built-in finisher POD not-reaching jam Built-in finisher POD remaining jam Console finisher entry port sensor (FES) not-reaching jam Console finisher entry port sensor (FES) remaining jam Console finisher saddle not-reaching jam (Not reaching the folding sensor (FFPS).) Console finisher saddle remaining jam (The folding sensor (FFPS) does not turn off.) Console finisher staple jam (The stapler does not complete clinching.) Console finisher punch jam (The puncher does not complete punching.) Console finisher door open jam (During/after paper passing, the front door, joint, or upper cover is opened.) Mail box PID not-reaching jam Mail box PID remaining jam Mail box MPPD1 not-reaching jam Mail box MPPD1 remaining jam Mail box MPPD2 not-reaching jam Mail box MPPD2 remaining jam Mail box MPPD3 not-reaching jam Mail box MPPD3 remaining jam Mail box MPPD4 not-reaching jam Mail box MPPD4 remaining jam Mail box MPPD5 not-reaching jam Mail box MPPD5 remaining jam
22-5 Purpose Function (Purpose) Item Other Used to check the ROM version of each unit (section). Software
Operation/Procedure The ROM version of each section can be checked. When there is any problem in the software, use this simulation to check the ROM version of each section and revise the version if necessary. S/N MFP (LANGUAGE) BOOT FAX NIC PCU SCANNER FINISHER DESK MAIL BIN PUNCH UNIT Engine section serial number MFP controller (Language version) MFP controller boot ROM FAX controller Network card PCU controller Scanner controller Finisher controller Desk/LCC controller mail bin controller Punch unit
SIMULATION 22-5 ROM VERSION DATA DISPLAY. S/N: 0000000000 MFP: 1.00 (LANGUAGE:1.00) PCU: 1.00 BOOT: SCANNER: 1.00 FAX: FINISHER: 1.00 NIC: DESK: 1.00 MAIL BIN: PUNCH UNIT: 1.00
22-6 Purpose Adjustment/Setup/Operation data output/Check (Display/Print) Used to output the list of the setting and adjustment data (simulations, FAX soft switch, counters). Data Adjust/Setting data
SIMULATION 22-3 PAPER JAM HISTORY. *******,*******,*******,* * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * *******,*******,*******,* * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * *******,*******,*******,* * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * *******,*******,*******,* * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * *******,*******,*******,* * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * * , * * * * * * *
Operation/Procedure When installing or servicing this machine, execute this simulation to print and save various setting and adjustment data for next servicing. (For example, memory trouble, PWB replacement, etc.) 1) Enter 1 with 10-key. 2) Press [START] key. The various setting and adjustment data are printed out. (The print paper cannot be selected optionally.) 0 TRAY SELECT PRINT START TRAY SELECT auto only (Selection is not allowed.) PRINT START
(10 lines, 80 digits = 800 characters) 22-4 Purpose Function (Purpose) Item Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the trouble (self diag) history. Trouble
Operation/Procedure The trouble history is displayed. The trouble history is displayed sequentially from the latest one. The max. 100 items can be stored. (The oldest one is deleted sequentially. The trouble position can be identified by the data.)
SIMULATION 22-4 TROUBLE HISTORY. **-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-** **-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-** **-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-** **-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-** **-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**
SIMULATION 22-6 DATA PRINT MODE. SELECT SETTING, AND PRESS START. 0. TRAY SELECT :AUTO ONLY 1. PRINT START
0
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 20
manuals4you.com
22-7 Purpose Function (Purpose) Item Adjustment/Setup/Operation data output/Check (Display/Print) Used to display the key operator code. (This simulation is used when the customer forgets the key operator code.) Data User data
22-10 Purpose Function (Purpose) Item Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the system configuration (option, internal hardware). Specifications Options
Operation/Procedure The system configuration is displayed. (The model names of the installed devices and options are displayed.) MACHINE AR-311S, AR-351S/AR-M355U, AR-451S/AR-M455U, AR-311FP, AR-351FP/AR-M351U, AR-451FP/ AR-M451U, AR-311N, AR-351N/M355N/M351N, AR-451N/M455N/M451N (Model code) NONE/ (Model code) NONE/ (Model code) NONE/ (Model code) NONE/ (Model code) NONE/ (Model code) Memory capacity (MB) Hard disk capacity (MB) Board type NONE/ (Model code) NONE/ (Network scanner) NONE/ (PS3 expansion kit) NONE/ (Model code) FAX expansion memory capacity (MB) NONE/ (Model code) Finisher stamp NONE/ (Model code) PCU PWB type (JPN: Japan/ EX100: EX Japan 100V/ EX200: EX Japan 200V)
22-8 Purpose Function (Purpose) Section Item Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the number of use of the finisher, the SPF, and the scan (reading) unit. Optical (Image scanning) Finisher Counter
Operation/Procedure The values of the finisher counter, the scanner (read), counter, and the SPF related counters are displayed. SPF SCAN STAPLER PUNCH STAMP Document feed quantity Number of scans Number of stapling Number of punching Number of SPF finish stamps
SPF FINISHER MAIL BIN PUNCH DESK/LCC ADU SYSTEM MEMORY HDD ICU NIC NSCN PS3 FAX FAX MEMORY HAND SET STAMP PCU TYPE
SIMULATION 22-8 ORG./STAPLE COUNTER DATA DISPLAY. SPF: ******** SCAN: ******** STAPLER: ******** PUNCH: ******** STAMP: ********
(Model code list) Item MACHINE Display AR-311S AR-351S/ AR-M355U AR-451S/ AR-M455U AR-311FP AR-351FP/ AR-M351U AR-451FP/ AR-M451U AR-311N AR-351N/ M355N/ M351N AR-451N/ M455N/ M451N ---AR-EF4 AR-EF3 ---AR-FN6 AR-FN7 ---AR-MS1 Content 31-sheet S model 35-sheet S/U model 45-sheet S/U model 31-sheet FP model (Local printer standard provision model) 35-sheet FP/U model (Local printer standard provision model) 45-sheet FP/U model (Local printer standard provision model) 31-sheet N model 35-sheet N model
22-9 Purpose Function (Purpose) Section Item Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the number of use (print quantity) of each paper feed section. Paper feed, ADU Counter
Operation/Procedure The values of the paper feed related counters are displayed. TRAY1 TRAY2 TRAY3/LCC1 TRAY4/LCC2 BPT ADU Use quantity of tray 1 Use quantity of tray 2 (Multi purpose tray) Use quantity of tray 3/LCC left tray (Common to Desk/LCC) Use quantity of tray 4/LCC right tray Use quantity of manual feed tray Use quantity of duplex paper feed
45-sheet N model
SPF
SIMULATION 22-9 PAPER FEED COUNTER DATA DISPLAY. TRAY1: ******** TRAY2: ******** TRAY3/LCC1:******** TRAY4/LCC2:******** BPT: ******** ADU: ********
FINISHER
MAIL BIN
Document feed unit not installed Document feed unit (SPF) installed Duplex document feed unit (DSPF) installed After-work unit not installed Built-in finisher installed Console finisher installed Mail bin not installed Mail bin installed
ADU
---AR-MU2 AR-D27 AR-D28 ICU TYPE-U/S TYPE-U/FP TYPE-N MEMORY 0MB ***MB HD 0MB ****MB NIC ---AR-NC7J PS3 ---expansion kit AR-PK6 FAX ---AR-FX12 Network ---scanner AR-NS3 Expansion ---memory AR-MM9 Handset ---AR-HN5 Finish stamp ---AR-SU1
DESK
Content Punch unit not installed Punch unit 2 holes Punch unit 3 holes Punch unit 4 holes Punch unit 4 holes wide hole Duplex module not installed Duplex module installed Duplex module + manual feed unit installed Paper feed desk not installed Multi-purpose tray installed Paper feed desk installed Tandem desk installed For U/S model board For U/FP model board For N model board No expansion memory Expansion memory ***MB Hard disk not installed Hard disk installed (AR-HD3) NIC not installed NIC installed PS3 expansion kit not installed PS3 expansion kit installed FAX expansion kit not installed FAX expansion kit installed Network expansion kit not installed Network expansion kit installed Expansion memory for FAX not installed Expansion memory for FAX 8MB (AR-MM9) installed handset not installed Handset installed Finish stamp unit not installed Finish stamp unit installed
SIMULATION 22-11 FAX COUNTER DATA DISPLAY. FAX SEND: ******** FAX RECEIVE : ******** FAX OUTPUT:******** SEND IMAGES: ******** SEND TIME: ********:**:** RECEIVE TIME: ********:**:**
22-12 Purpose Function (Purpose) Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the SPF misfeed positions and the number of misfeed at each position. (When the number of misfeed is considerably great, it can be judged as necessary for repair.) DSPF Trouble
Section Item
Operation/Procedure The history of paper jam and misfeed is displayed. The misfeed history is displayed sequentially from the latest one. The max. 20 items are recorded. (The oldest one is sequentially deleted.) This data can be used to identify the trouble position. The latest 20 data of document jam history are displayed. (Refer to the jam code below.) (Jam cause code) Code NO_JAM_CAUSE SPPD_N SPPD_S STD_N STD_S SPOD_N SPOD_S SPSDSCN Description No jam. Also used to cancel a jam. SPPD not-reached jam SPPD remaining jam STD not-reached jam STD remaining jam SPOD not-reached jam SPOD remaining jam Exposure start timer end
SIMULATION 22-10 SYSTEM INFORMATION. MACHINE:******* SPF:******* FINISHER:******* MAIL BIN:******* PUNCH:****** DESK/LCC:******* ADU:******* SYSTEM MEMORY:**MB HDD:***MB ICU:****** NIC:******* NSCN:****** PS3:****** FAX:******* FAX MEMORY:**MB HAND SET:******* STAMP:******* PCU TYPE:*******
(10 lines, 80 digits = 800 characters) 22-13 Purpose Function (Purpose) Item Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the operating time of the process section (OPC drum, DV unit, toner bottle). Counter
22-11 Purpose Function (Purpose) Section Item Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the use frequency (send/receive) of FAX. (Only when FAX is installed) FAX Data
Operation/Procedure The rotating time and the print quantity of the process section (OPC drum, DV unit (developer), toner motor (toner bottle)) are displayed. DRUM TONER DEVE OPC drum Toner motor DV unit Count value (counts) Rotating time (sec) Count value (counts) Rotating time (sec) Count value (counts) Rotating time (sec)
Operation/Procedure The values of the FAX send counter and the FAX receive counter are displayed. FAX SEND FAX RECEIVE FAX OUTPUT SEND IMAGES SEND TIME RECEIVE TIME Number of FAX send Number of FAX receive Number of FAX print Send quantity Send time Receive time
manuals4you.com
SIMULATION 22-13 PROCESS DATA DISPLAY. DRUM: ********(counts) TONER: ********(counts) DEVE: *********(counts)
SIMULATION 23-2 JAM/TROUBLE DATA PRINT MODE SELECT SETTING, AND PRESS START. 0. TRAY SELECT AUTO ONLY 1. PRINT START
22-19 Purpose Function (Purpose) Section Item Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the values of the counters related to the scan mode and the internet FAX mode. Scanner Counter
Operation/Procedure The values of the counters related to the scan mode and the internet FAX mode are displayed. NETWORK SCANNER ORIGINAL COUNTER MAIL COUNTER FTP COUNTER INTERNET-FAX ORIGINAL COUNTER INTERNET-FAX SEND Document scan quantity (OC, SPF total quantity) Number of times of mail send Number of times of FTP send Document scan quantity (OC, SPF, total quantity) Number of times of internet FAX send INTERNET-FAX RECEIVE Number of times of internet FAX receive INTERNET-FAX OUTPUT Internet FAX print quantity SCAN TO HDD Scan to HDD record quantity INTERNET-FAX SEND IFAX send quantity counter IMAGES MAIL SEND IMAGES MAIL send quantity counter FTP SEND IMAGES FTP send quantity counter
SIMULATION 22-19 NETWORK SCANNER AND INTERNET-FAX COUNTER DISPLAY. NETWORK SCANNER ORIGINAL COUNTER: ********* MAIL COUNTER: ******** FTP COUNTER: ******** INTERNET-FAX ORIGINAL COUNTER: ******** INTERNET-FAX SEND: ******** INTERNET-FAX RECEIVE: ******** INTERNET-FAX OUTPUT: ******** SCAN TO HDD : ******** INTERNET-FAX SEND IMAGES: ******** MAIL SEND IMAGES: ******** FTP SEND IMAGES: ********
23-80 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operations of the sensors and detectors in the paper feed and transport section. Paper feed, paper transport Operation
Operation/Procedure 1) Select "2. PRINT PATTERN." 2) Press [START] key. 3) Select "1" (Paper transport time data) with 10-key. 4) Press [START] key. The list of the ON time of the sensors and the detectors of the paper transport section is printed. When a paper jam or misfeed is generated, the ON time of each sensor and detector is checked to check if the operation of the sensor and the detector, paper feed, and transport are normal or not. 0 1 2 TRAY SELECT AUTO ONLY PRINT START PRINT PATTERN Auto only (No selection allowed) Print execution Print of the set data is executed. Print pattern 1. Paper transport time data
SIMULATION 23-80 DATA PRINT MODE. SELECT SETTING, AND PRESS START. 0. TRAY SELECT :AUTO ONLY 1. PRINT START 2. PRINT PATTERN:1
23
23-2 Purpose Function (Purpose) Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the trouble history of paper jam and misfeed. (If the number of misfeed and troubles is considerably great, it may be judged as necessary to repair.) Trouble
0
Select 2 and press [START] key. Press [CUSTOM SETTING] key or [START] key.
Item
SIMULATION 23-80 DATA PRINT MODE. INPUT VALUE, AND PRESS START. (PRINT PATTERN) INPUT 1.
Operation/Procedure 1) Select "1. PRINT START." 2) Press [START] key. The trouble history of paper jam and misfeed is printed. This data can be cleared by SIM 24-1. AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 23
24
24-1 Data clear Used to clear the misfeed counter, the misfeed history, the trouble counter, and the trouble history. (The counters are cleared after completion of maintenance.) Item Counter Operation/Procedure 1) Select the counter to be cleared with 10-key. 2) Press [START] key. The confirmation to clear is opened. 3) Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear 4) Press [START] key. 1 2 3 PAPER JAM SPF JAM TROUBLE Number of paper jams Number of SPF jams Number of troubles Purpose Function (Purpose)
SIMULATION 24-2 PAPER FEED COUNTER DATA CLEAR. SELECT1-6, AND PRESS START. 1. TRAY1 2. TRAY2 3. TRAY3/LCC1 4. TRAY4/LCC2 5. BPT 6. ADU
Data clear Used to clear the number of use of the finisher, SPF, and the scan (reading) unit. Counter
SIMULATION 24-1 JAM/ TROUBLE COUNTER DATA CLEAR. SELECT1-3, AND PRESS START. 1. PAPER JAM 2. SPF JAM 3. TROUBLE
Operation/Procedure 1) Select the counter to be cleared with 10-key. 2) Press [START] key. The confirmation to clear is opened. 3) Select Yes/NO of counter clear with 10-key. YES: Clear
NO: Not clear 4) Press [START] key. 1 2 3 4 5 SPF SCAN STAPLER PUNCH STAMP SPF paper pass quantity Number of times of document scan Number of times of stapling Number of times of punching Number of times of SPF finish stamp
* = PAPER JAM, SPF JAM, TROUBLE 24-2 Purpose Function (Purpose) Section Item Data clear Used to clear the number of use (the number of prints) of each paper feed section. Paper feed Counter
SIMULATION 24-3 ORG./STAPLE COUNTER DATA CLEAR. SELECT 1-5, AND PRESS START. 1. SPF 2. SCAN 3. STAPLER 4. PUNCH 5. STAMP
Operation/Procedure 1) Select the counter to be cleared with 10-key. 2) Press [START] key. The confirmation to clear is opened. 3) Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear 4) Press [START] key. 1 2 3 4 5 6 TRAY1 TRAY2 TRAY3/LCC1 TRAY4/LCC2 BPT ADU Tray 1 use quantity Tray 2 use quantity Tray 3/LCC left tray use quantity Tray 4/LCC right tray use quantity Manual feed tray use quantity Duplex feed quantity
manuals4you.com
24-4 Purpose Data clear Function Used to reset the maintenance counter. (Purpose) Item Counter Operation/Procedure 1) Select the counter to be cleared with 10-key. 2) Press [START] key. The confirmation to clear is opened. 3) Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear 4) Press [START] key. 1 MAINTENANCE Maintenance counter
24-6 Purpose Function (Purpose) Item Data clear Used to reset the copy counter. Counter Copy
Operation/Procedure 1) Select the counter to be cleared with 10-key. 2) Press [START] key. The confirmation to clear is opened. 3) Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear 4) Press [START] key. 1 COPY Copy effective paper counter
1
Press [START] key. Press [CUSTOM SETTINGS] key or [START] key. Press [START] key.
1
Press [CUSTOM SETTINGS] key or [START] key.
* = MAINTENANCE * = COPY 24-5 Purpose Function (Purpose) Section Item Data clear Used to reset the developer counter. (The developer counter of the DV unit which is installed is reset.) Image process (Photoconductor/Developing/ Transfer/Cleaning) Counter Developer 24-7 Purpose Function (Purpose) Section Item Data clear Used to clear the OPC drum counter. (Perform this simulation when the OPC drum is replaced.) Image process (Photoconductor/Developing/ Transfer/Cleaning) Counter Photo conductor
Operation/Procedure 1) Select the counter to be cleared with 10-key. 2) Press [START] key. The confirmation to clear is opened. 3) Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear 4) Press [START] key. 1 DV CARTRIDGE Developer cartridge
Operation/Procedure 1) Select the counter to be cleared with 10-key. 2) Press [START] key. The confirmation to clear is opened. 3) Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear 4) Press [START] key. After replacing the OPC drum, be sure to clear the OPC drum counter. 1 DRUM OPC drum counter
1
Press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
* = DV CARTRIDGE
24-10
SIMULATION 24-7 DRUM COUNTER DATA CLEAR. SELECT1, AND PRESS START. 1. DRUM
Data clear Used to clear the FAX counter. (Only when FAX is installed) FAX Counter
Operation/Procedure
Press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
1) Select the counter to be cleared with 10-key. 2) Press [START] key. The confirmation to clear is opened.
1
1 2 3 4 5 6
NO: Not clear 4) Press [START] key. FAX SEND FAX RECEIVE FAX OUTPUT SEND IMAGES SEND TIME RECEIVE TIME Number of times of FAX send Number of times of FAX receive FAX print quantity Send quantity Send time Receive time
* = DRUM 24-9 Purpose Function (Purpose) Section Item Data clear Used clear the printer mode print counter and the self print mode print counter. Printer Counter
Operation/Procedure 1) Select the counter to be cleared with 10-key. 2) Press [START] key. The confirmation to clear is opened. 3) Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear 4) Press [START] key. After replacing the OPC drum, be sure to clear the OPC drum counter. 1 2 PRINTER OTHERS Printer counter (Print mode) Other effective paper counter (Self print mode)
SIMULATION 24-10 FAX COUNTER DATA CLEAR. SELECT1-6, AND PRESS START. 1. FAX SEND 2. FAX RECEIVED 3. FAX OUTPUT 4. SEND IMAGES 5. SEND TIME 6. RECEIVE TIME
SIMULATION 24-9 PRINTER/OTHERS COUNTER DATA CLEAR. SELECT1-2, AND PRESS START. 1. PRINTER 2. OTHERS
* = FAX SEND, FAX RECEIVED, FAX OUTPUT, SEND IMAGES, SEND TIME, RECEIVE TIME 24-11 Purpose Function (Purpose) Section Item Data clear Used to reset the OPC drum rotation time, and the DV unit rotation time counter. The developer counter in the DV unit installed is reset. Image process (Photoconductor/Developing/ Transfer/Cleaning) Counter Developer
Operation/Procedure 1) Select the counter to be cleared with 10-key. 2) Press [START] key. The confirmation to clear is opened. 3) Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear 4) Press [START] key. 1 2 DRUM ROTATION DV ROTATION OPC drum rotation time DV unit rotation time
* = PRINTER, OTHERS
manuals4you.com
SIMULATION 24-11 TIMER DATA CLEAR. SELECT1-2, AND PRESS START. 1. DRUM ROTATION 2. DV ROTATION
SIMULATION 24-15 NETWORK SCANNER AND INTERNET-FAX COUNTER CLEAR. SELECT1-3, AND PRESS START. 1. NETWORK SCANNER ORIGINAL COUNTER 2. MAIL COUNTER 3. FTP COUNTER 4. INTERNET-FAX ORIGINAL COUNTER: ******** 5. INTERNET-FAX SEND: ******** 6. INTERNET-FAX RECEIVE: ******** 7. INTERNET-FAX OUTPUT: ******** 8. SCAN TO HDD: ******** 9. INTERNET-FAX SEND IMAGES: ******** 10. MAIL SEND IMAGES: ******** 11. FTP SEND IMAGES: ******** 12. DOC FILING OUTPUT: ********
24-15 Purpose Function (Purpose) Item Data clear Used to clear the counters related to the scan mode and the internet FAX mode. Counter
SIMULATION 24-15 * COUNTER DATA CLEAR. ARE YOU SURE? 1. YES 2. NO
Operation/Procedure 1) Select the counter to be cleared with 10-key. 2) Press [START] key. The confirmation to clear is opened. 3) Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear 4) Press [START] key. Document scan quantity counter in the network scanner mode 2 MAIL COUNTER Number of times of mail send 3 FTP COUNTER Number of times of FTP send 4 INTERNET-FAX Internet FAX document scan ORIGINAL quantity (Total quantity of OC COUNTER and SPF) 5 INTERNET-FAX SEND Number of times of internet FAX send 6 INTERNET-FAX RECEIVE Number of times of internet FAX receive 7 INTERNET-FAX OUTPUT Internet FAX print quantity 8 SCAN TO HDD SCAN TO HDD record quantity 9 INTERNET-FAX SEND IFAX send quantity counter IMAGES 10 MAIL SEND IMAGES MAIL send quantity counter 11 FTP SEND IMAGES FTP send quantity counter 12 DOC FILING OUTPUT Document filing print counter. 1 NETWORK SCANNER ORIGINAL COUNTER * = NETWORK SCANNER ORIGINAL, MAIL, FTP, INTERNETFAX ORIGINAL COUNTER, INTERNET-FAX SEND, INTERNET-FAX RECEIVE, INTERNET-FAX OUTPUT, SCAN TO HDD, INTERNET-FAX SEND IMAGES, MAIL SEND IMAGES, FTP SEND IMAGES, DOC FILING OUTPUT
25
25-1 Operation test/Check Used to check the operations of the developing section (toner concentration, humidity and toner concentration sensor, humidity sensor, temperature sensor output can be monitored.) Section Process (Developing section) Item Operation Operation/Procedure Press [START] key. The developing motor and the OPC drum motor rotate, and the toner concentration detection level and the humidity sensor detection level and the temperature sensor detection level are displayed.
SIMULATION 25-1 TONER SENSOR OUTPUT MONITOR. PRESS START. HUMIDITY AREA : 70.0 - 72.5 TEMPERATURE AREA: 70.0 - 72.5 DEVE REFERENCE : 128
Press [CUSTOM SETTINGS] key, and the operation is stopped immediately or after 2 min.
SIMULATION 25-1 DV MONITOR. EXECUTING. HUMIDITY AREA : 70.0 - 72.5 TEMPERATURE AREA: 70.0 - 72.5 DEVE REFERENCE : 128
25-2 Purpose Function (Purpose) Section Setting Used to make the initial setting of toner concentration when replacing developer. Image process (Photoconductor/Developing/ Transfer/Cleaning)
SIMULATION 26-3 AUDITOR SETUP. SELECT 1-3, AND PRESS START. 1.P10 2.VENDOR 3.OTHERS 4.VENDOR-EX 5.VENDOR-EX+
Operation/Procedure 1) Press [START] key. The developing motor rotates for 2 min and the toner concentrations sensor makes sampling of toner concentration 16 times, and the detection level is displayed. After the developing motor stops, the average value of toner concentration sampling is set as the reference toner concentration level. NOTE: When the above operation is interrupted on the way, the reference toner concentration level is not set. Also when error code of EE-EL or EE-EU is displayed, the reference toner concentration level is not set normally. (Default: 118) 2) The humidity near the developing tank at the developing adjustment is registered.
SIMULATION 25-2 AUTOMATIC DV ADJUSTMENT. PRESS START. HUMIDITY AREA : 70.0 - 72.5 TEMPERATURE AREA: 70.0 - 72.5 DEVE REFERENCE : 118
26-5 Purpose Setting Function Used to set the count mode of the total counter (Purpose) and the maintenance counter. Item Specifications Counter Operation/Procedure 1) Select the number corresponding to the counter to be set with 10-key. 2) Press [START] key. 3) Select the count mode with 10-key. 4) Press [START] key. Set the count-up (1 or 2) for A3/WLT paper. (Select the target counter.) 1 2 3 1 2 TOTAL COUNTER MAINTENANCE (DRUM) COUNTER DV COUNTER 1 COUNT UP 2 COUNT UP Total counter Maintenance counter/ OPC drum counter Developer counter
Press [CUSTOM SETTINGS] key, and the operation is stopped immediately or after 2 min.
SIMULATION 25-2 AUTOMATIC DV ADJUSTMENT. EXECUTING. HUMIDITY AREA : 70.0 - 72.5 TEMPERATURE AREA: 70.0 - 72.5 DEVE REFERENCE : 118
SIMULATION 26-5 A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-3, AND PRESS START. 1. TOTAL COUNTER 1 2. MAINTENANCE(DRUM) COUNTER 1 3. DV COUNTER 1
26
26-3 Purpose Function (Purpose) Section Item Setting Used to set the specifications of the auditor. Setting must be made according to the auditor use conditions. Auditor Specifications
SIMULATION 26-5 A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-2, AND PRESS START. 1. TOTAL COUNTER (1: 1COUNT UP, 2: 2COUNT UP)
26-6 Purpose Function (Purpose) Item Setting Used to set the specifications (paper, document detection, etc.) of the destination. Specifications Destination
Operation/Procedure 1) Select the number corresponding to the auditor mode with 10key. 2) Press [START] key. 1 2 3 4 5 P10 VENDOR OTHERS VENDOR-EX VENDOR-EX+ Built-in auditor mode Coin vendor mode Other Coin vendor mode (without temporarily charge) Coin vendor mode (without temporarily charge) + Document filing function enable
Operation/Procedure 1) Select the number corresponding to the destination with 10key. 2) Press [START] key. After completion of setting, the machine is automatically reset. 1 2 3 4 5 6 7 8 9 10 USA CANADA INCH JAPAN AB_B EUROPE UK AUSTRALIA AB_A CHINA United States of America Canada Inch series EX Japan AB series B5 Europe UK Australia AB series A5 China
(Default: 1)
manuals4you.com
Since this simulation cannot change the Fax destination, use SIM 66-2 to change the FAX destination.
SIMULATION 26-6 DESTINATION SETUP. SELECT 1-10, AND PRESS START. 1.USA 2.CANADA 3.INCH 4.JAPAN 5.AB_B 6.EUROPE 7.UK 8.AUSTRALIA 9.AB_A 10.CHINA
26-35 26-10 Purpose Function (Purpose) Item Setting Used to set the network scanner trial mode. Operation Section Item Purpose Function (Purpose) Setting Used to set whether the same continuous troubles are displayed as one trouble or the series of troubles with SIM 22-4 when the same troubles occur continuously. Specifications
Operation/Procedure 1) Select START/END of the network scanner trial mode with 10key. 2) Press [START] key. Max. 500 menus can be scanned. 0 1 END START Trial mode cancel Trial mode start Default
Operation/Procedure 1) Select the number corresponding to the operation mode with 10-key. 2) Press [START] key. 0 ONCE When two or more troubles of a same kind occur continuously, the troubles are displayed as one trouble in the trouble history of SIM22-4. When two or more troubles of a same kind occur continuously, the troubles are displayed straightly as two or more troubles in the trouble history of SIM22-4.
SIMULATION 26-10 NETWORK SCANNER TRIAL SETTING. SELECT 0-1, AND PRESS START. 0.END 1.START
ANY
(Default: 0) 26-18 Purpose Function (Purpose) Setting Used to set YES/NO of toner save operation. (This function is valid only in Japan and UK versions. (Depends on the destination setting of SIM26-6.) For the other destinations, the same setting can be made by the user program P22.) Specifications Operation mode
SIMULATION 26-35 TROUBLE MEMORY MODE SETTING. SELECT 0-1, AND PRESS START. 0. ONCE 1. ANY
Item
26-38 Purpose Function (Purpose) Section Item Setting Used to set CONTINUE/STOP of printing when maintenance timing is over and the count value reaches 110% of replacement timing (life). Other Specifications
Operation/Procedure 1) Select YES/NO of the toner save mode with 10-key. 2) Press [START] key. 0 1 YES NO Toner save mode is set. Toner save mode is not set. Default
Operation/Procedure
SIMULATION 26-18 TONER SAVE MODE SETTING. SELECT 0-1, AND PRESS START. 0. YES 1. NO
1) Select the number corresponding to the operation mode with 10-key. 2) Press [START] key. 0 1 PRINT CONTINUE PRINT STOP Print continue Print stop
(Default: 0) 26-30 Purpose Function (Purpose) Item Setting Used to set the operation mode conforming to the CE mark (Europe safety standards). (Conforming to soft start when driving the fusing heater lamp.) Specifications Operation mode (Common)
SIMULATION 26-38 LIFE OVER SETTING. SELECT 0-1, AND PRESS START. 0. PRINT CONTINUE 1. PRINT STOP
Operation/Procedure 1) Select the number corresponding to the operation mode with 10-key. 2) Press [START] key. 0 1 NO YES CE mark control NO (Normal operation) CE mark control YES (Heater lamp soft start operation) AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 29
26-41 Purpose Setting Function Used to set the automatic magnification ratio (Purpose) selection (AMS) in the pamphlet mode. Section Item Specifications Operation mode (Common) Operation/Procedure 1) Enter the number corresponding to whether AMS operation is automatically performed or nor in the center binding mode with the 10-key. 2) Press [START] key. 0 1 NO YES AMS/APS selection allowed AMS is forcibly operated.
26-68 Purpose Function (Purpose) Section Item Setting Used to set ENABLE/DISABLE of the CA key cancel function of print stop. Specifications Operation
Operation/Procedure 1) Select ENABLE/DISABLE of the CA key cancel function of print stop with 10-key. 2) Press [START] key. 0 1 26-50 Purpose Function (Purpose) Item Setting Black-White reverse YES/NO setting Specifications Operation DISABLE ENABLE (PRINT STOP) Disable Enable
(Default: 1)
SIMULATION 26-68 CA KEY CANCEL MODE SETTING. SELECT 0-1, AND PRESS START. 0. DISABLE 1. ENABLE (PRINT STOP)
Operation/Procedure 1) Select ENABLE/DISABLE of the B/W reverse mode with 10key. 2) Press [START] key. 0 1 DISABLE ENABLE B/W reverse mode DISABLE B/W reverse mode ENABLE Default
27
27-1 Purpose Function (Purpose) Setting Used to set the specifications for operations in case of communication trouble between the host computer and MODEM (machine side). (When communication trouble occurs between the host computer MODEM and the machine, the self diag display (U7-00) is printed and setting for inhibition of print or not is made.) Communication unit (TEL/LIU/MODEM etc.) Specifications Operation mode
SIMULATION 26-50 B/W REVERSE MODE SETTING. SELECT 0-1, AND PRESS START. 0. DISABLE 1. ENABLE
26-52 Purpose Function (Purpose) Section Item Setting Used to set whether non-print paper (insertion paper, cover paper) (blank image print paper) is counted up or not. Paper transport (Discharge/Switchback/Transport) Specifications Operation mode
Section Item
Operation/Procedure 1) Select the number corresponding to the operation mode with 10-key. 2) Press [START] key. 0 YES Though a communication trouble occurs between the host computer and the MODEM (machine side), there is no effect on the machine operations. When a communication trouble occurs between the host computer and the MODEM (machine side), the self diag display (U7-00) is displayed and printing is inhibited.
Operation/Procedure 1) Select YES/NO of the non-print paper count-up with 10-key. 2) Press [START] key. Non-print paper means an insert paper (without copying) in the OHP insertion mode, a cover (without copying) in the cover insertion mode, back surface, and white paper in the duplex exit mode (CA, etc.). 0 1 NO (NO COUNT UP) YES (COUNT UP) No count up Count up
NO
(Default: 0)
SIMULATION 27-1 DISABLING OF U7-00 TROUBLE. SELECT 0-1, AND PRESS START. 0. YES 1. NO
(Default: 0 for Japan and Australia, 1 for the other) The target counters are as follows: Copies counter Printer counter Department management counter Total counter
manuals4you.com
27-5 Purpose Function (Purpose) Section Item Setting Used to enter the machine tag No. (This function allows to check the tag No. of the machine with the host computer.) Communication unit (TEL/LIU/MODEM etc.) Specifications Operation mode
Operation/Procedure 1) Enter the tag number with 10-key. 2) Press [START] key.
SIMULATION 27-5 TAG # SETTING. INPUT VALUE, AND PRESS START. PRESENT: 00010000 NEW: 00009999
30
30-1 Purpose Function (Purpose) Item Operation test/Check Used to check the operation of sensors and detectors in other than the paper feed section and the operations of the related circuits. Operation
CSS1 PED LUD MCSET MCDRS MCPPD MCLUD MCPED MCSPD MCSS1 MCSS2 MCSS3 MCSS4 MP Tray size MPFSET MPED MPLD MPLS1 MPLS2 Bypass Tray size
Tray 1 insertion detection Tray 1 paper empty detection Tray 1 upper limit detection MP unit detection MP unit side door open detection MP tray transport detection MP tray upper limit detection MP tray paper empty detection MP tray remaining quantity detection MP tray size detection 1 MP tray size detection 2 MP tray size detection 3 MP tray size detection 4 (The detection size of MP tray is displayed.) Manual feed tray detection Manual feed tray paper empty detection Manual feed length detection Manual feed pull-out sensor 1 Manual feed pull-out sensor 2 (The detection size of manual feed tray is displayed.)
Operation/Procedure The operating conditions of sensors and detectors are displayed. The active sensors and detectors are highlighted. PPD1 POD1 POD2 POD3 DSWL DSWF Resist roller front paper detection After-fusing transport detection 1 After-fusing transport detection 2 Paper full detection Cabinet open detection Front door
SIMULATION 30-2 TRAY SENSOR CHECK.. CSS PED LUD MCSET MCDRS MCPPD MCLUD MCPED MCSPD MCSS1 MCSS2 MCSS3 MCSS4 (MP Tray size: A4 ) MPFSET MPED MPLD MPLS1 MPLS2 (Bypass Tray size: A3 )
40
40-1 Purpose Function (Purpose) Operation test/Check Used to check the operation of the manual feed tray paper size detector and the related circuit. (The operation of the manual feed tray paper size detector can be monitored with the LCD display.) Paper feed Operation
POD3
DSWL
Section Item
Operation/Procedure 30-2 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of sensors and detectors in the paper feed section and the related circuits. Paper feed Operation The operating conditions of sensors and detectors are displayed. The active sensors and detectors are highlighted. The paper width size detection level is displayed. MPLD MPLS1 MPLS2 BYPASS_WIDTH BYPASS_AD Bypass Tray width size Manual tray length detection Manual tray pull-out detection 1 Manual tray pull-out detection 2 Manual feed guide plate position Manual feed width detection volume output AD value (Manual tray detection size is displayed.) A4/A3, 11 x, B5/B4, 8.5 x , A4R, B5R, A5R, 5.5x, 7.25x, EXTRA
Operation/Procedure The operating conditions of sensors and detectors are displayed. The active sensors and detectors are highlighted.
SIMULATION 40-1 BYPASS TRAY SENSOR CHECK.. MPLD MPLS1 MPLS2 BYPASS_WIDTH: 2100 BYPASS_AD: 600 (Bypass Tray width size: A4/A3)
40-2 Purpose Function (Purpose) Section Item Adjustment Used to adjust the manual paper feed tray paper width detector detection level. Paper feed Operation
40-7 Purpose Function (Purpose) Section Item Adjustment/Setup Used to enter the manual paper feed tray paper width adjustment value. Paper feed Operation
Operation/Procedure 1) Open the manual paper feed guide to the max. width. 2) Select MAX POSITION with 10-key. 3) Press [START] key. The max. width detection level is recognized. 4) Press [CUSTOM SETTINGS] key. 5) Set the manual paper feed guide to A4R size width. 6) Select POSITION with 10-key. 7) Press [START] key. The A4R width detection level is recognized. 8) Press [CUSTOM SETTINGS] key. 9) Set the manual paper feed guide to A5/A5R size width. 10) Select POSITION2 with 10-key. 11) Press [START] key. The A5R width detection level is recognized. 12) Press [CUSTOM SETTINGS] key. 13) Open the manual paper feed guide to the min. width. 14) Select MIN POSITION with 10-key. 15) Press [START] key. The min. width detection level is recognized. If the above procedures are not completed normally, "ERROR" is displayed. If completed normally, "COMPLETE" is displayed.
Operation/Procedure 1) Select the number corresponding to the set item with 10-key. 2) Press [START] key. 3) Enter the set value with 10-key. 4) Press [START] key. 1 2 3 4 MAX. POSITION POSITION 1 POSITION 2 MIN. POSITION Max. width Adjustment point 1 Adjustment point 2 Min. value
SIMULATION 40-7 BYPASS TRAY VALUE SETTING. SELECT 1-4, AND PRESS START. 1. MAX. POSITION : 66 2. POSITION 1 : 447 3. POSITION 2 : 704 4. MIN. POSITION : 916
SIMULATION 40-7 BYPASS TRAY VALUE SETTING. INPUT VALUE 0-1023, AND PRESS START. 1. MAX. POSITION
66
SIMULATION 40-2 BYPASS TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START. 1. MAX. POSITION 2. POSITION 1 3. POSITION 2 4. MIN. POSITION
40-11 Purpose Function (Purpose) Section Item Operation test/Check Used to check the multi-purpose tray width detection adjustment value. Paper feed Operation
SIMULATION 40-2 BYPASS TRAY ADJUSTMENT. MAX. POSITION COMPLETE (or "ERROR")
Operation/Procedure The operating conditions of sensors and detectors are displayed. The active sensors and detectors are highlighted. The paper width detection level is also displayed. MCSS1 MCSS2 MCSS3 MCSS4 Multi Purpose Tray Tray 3 size detection 1 Tray 3 size detection 2 Tray 3 detection size 3 Tray 3 size detection 4 (MPT width direction detection size is displayed.) A4/A3, 11X, B5/B4, 8.5X, A4R, B5R, A5R, 5.5X, 7.25X, EXTRA
SIMULATION 40-11 TRAY3 SENSOR CHECK.. MCSS1 MCSS2 MCSS3 MCSS4 (Multi Purpose Tray width size: A4/A3)
SIMULATION 40-2 BYPASS TRAY ADJUSTMENT. MIN. POSITION COMPLETE (or "ERROR")
manuals4you.com
40-12 Purpose Function (Purpose) Section Item Adjustment/Setup Used to check the multi-purpose tray width detection adjustment value. Paper feed Operation
41-2 Purpose Function (Purpose) Section Item Adjustment Used to adjust the document size sensor sensing level. Other Operation
Operation/Procedure 1) Open the paper feed tray 2 paper feed guide to the max. width position. 2) Select MAX POSITION with 10-key. 3) Press [START] key. The max. width detection level is recognized. 4) Press [CUSTOM SETTINGS] key. 5) Open the paper feed tray 3 paper feed guide to the min. width position. 6) Select MIN POSITION with 10-key. 7) Press [START] key. The min. width detection level is recognized. If the above procedures are not completed normally, "ERROR" is displayed. If completed normally, "COMPLETE" is displayed.
SIMULATION 40-12 MULTI PURPOSE TRAY ADJUSTMENT. SELECT 1-2, AND PRESS START. 1.MAX. POSITION 2.MIN. POSITION
Operation/Procedure 1) Open the document cover and select NO ORIGINAL with 10key without placing any document on the document table. 2) Press [START] key. The sensor level is set without document on the document table. 3) Place an A3 document on the document table, and select A3 ORIGINAL with 10-key. 4) Press [START] key. The sensor level is set when detection the document. If the above procedures are not completed normally, "ERROR" is displayed. If completed normally, "COMPLETE" is displayed.
SIMULATION 41-2 PD SENSOR ADJUSTMENT. SELECT1-2, AND PRESS START. (PLEASE OPEN THE ORIGINAL COVER.) 1. NO ORIGINAL 2. A3 ORIGINAL
SIMULATION 40-12 MULTI PURPOSE TRAY ADJUSTMENT. MAX. POSITION COMPLETE (or "ERROR")
Press [START] key. Press [CUSTOM SETTINGS] key.
SIMULATION 41-2 PD SENSOR ADJUSTMENT. NO ORIGINAL COMPLETE (or "ERROR at PD1 PD2...") A3 ORIGINAL INCOMPLETE
Select 2 and press [START] key. (Error) Press [CUSTOM SETTINGS] key.
SIMULATION 40-12 MULTI PURPOSE TRAY ADJUSTMENT. MIN. POSITION COMPLETE (or "ERROR")
SIMULATION 41-2 PD SENSOR ADJUSTMENT. NO ORIGINAL COMPLETE A3 ORIGINAL COMPLETE (or "ERROR at PD1 PD2...")
41
41-1 Purpose Function (Purpose) Operation test/Check Used to check the operation of the document size sensor and the related circuit. (The operation of the document size sensor can be monitored with the LCD display.) Other Operation
41-3 Purpose Function (Purpose) Operation test/Check Used to check the operation of the document size sensor and the related circuit. (The document size sensor output level can be monitored with the LCD display.) Other Operation
Section Item
Operation/Procedure The detection output level (A/D value) of the document sensors (PD1 - PD7) is displayed in real time. The value in [ ] on the side of each sensor name indicates the threshold value. The light receiving value (A/D value) and the threshold value (A/D value) of PD1 - PD7 are in the range of 1 - 255. The default of threshold value is 128. OCSW PD1 - 7 Open: Normal display Close: Highlighted PD sensor detection level The value in [ ] indicates the adjustment threshold value (SIM41-2 adjustment value). Original cover status
Section Item
Operation/Procedure The operating conditions of sensors and detectors are displayed. The active sensors and detectors are highlighted. OCSW PD1 - 7 Document cover status Document detection sensor status Open: Normal display Close: Highlighted No document: Normal display Document present: Highlighted
PD4
PD5
PD6
PD7
SIMULATION 41-3 PD SENSOR DATA DISPLAY. OCSW PD1[128]: 200 PD2[128]: 200 PD3[128]: 50 PD4[128]: 52 PD5[128]: 51 PD6[128]: 50 PD7[128]: 52
SIMULATION 44-1 PROCESS CORRECTION VALUE SETTING. INPUT VALUE 0-255 AND PRESS START. BIT0:Vg1, BIT1:Ld1, BIT2:Vg2, BIT3:Ld2 BIT4:Vb1, Vb2 BIT5:Vg3, Vb3, Ld3 BIT6:Vbr BIT7:Vg4, Vb4, Ld4
111
43
43-1 Purpose Function (Purpose) Section Item Setting Used to set the fusing temperature in each operation mode. Fixing (Fusing) Operation
44-4 Purpose Function (Purpose) Section Item Setup Used to set the target image (reference) density level in the developing bias voltage correction. Process (OPC drum, developing, transfer, cleaning) Data
Operation/Procedure 1) Select the number corresponding to the setting mode with 10key. 2) Press [START] key. 3) Enter the set value. 4) Press [START] key. 1 Default 190 190 150 150 TEMP. AREA *1 Item Process environment temperature forcible setting value (0 - 13 /normal: 0) Process environment humidity forcible setting value (0 - 14 /normal: 0) Vb rising correction standby time (0 - 180 sec/default: 90) Vb correction amount (first rotation) (0 - 150V/default: 50) Vb correction amount (second rotation) (0-50V/default: 15)
Operation/Procedure 1) Select the number corresponding to the setting mode with 10key. 2) Press [START] key. 3) Press [CUSTOM SETTINGS] key. 4) Press [START] key. 1 2 3 4 Item INSIDE NORMAL Heater inside/normal OUTSIDE NORMAL Heater outside/normal INSIDE PREHEAT Heater inside/preheat OUTSIDE PREHEAT Heater outside/preheat
HUMIDITY AREA *1
3
SIMULATION 43-1 FUSER TEMPERATURE SET. SELECT 1-4, AND PRESS START. 1. INSIDE NORMAL 190 2. OUTSIDE NORMAL 190 3. INSIDE PREHEAT 150 4. OUTSIDE PREHEAT 150
4 5
*1: Only when this value is 0, control is made with the actual measurement value of the process thermistor (temperature/humidity). When it is not 0, control is made with the forcible setting value.
SIMULATION 44-4 PROCESS CONTROL VALUE SETTING. SELECT 1-5 AND PRESS START. 1.TEMP. AREA 0 2.HUMIDITY AREA 0 3.S_WT 100 4.Vb1 50 5.Vb2 50
SIMULATION 43-1 FUSER TEMPERATURE SET. INPUT VALUE, AND PRESS START. 1. INSIDE NORMAL
190
44
44-1 Purpose Function (Purpose) Section Item Setting Used to set enable/disable of correction operations in the image forming (process) section. Image process (Photoconductor/Developing/ Transfer/Cleaning) Operation
SIMULATION 44-4 PROCESS CONTROL VALUE SETTING. INPUT VALUE, AND PRESS START. 3.S_WT
101
manuals4you.com
44-9 Purpose Function (Purpose) Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the data related to the image forming section correction (process correction) result (corrected main charger grid voltage, the developing bias voltage, and the laser power voltage in each print mode). (This simulation allows to check that correction is performed normally or not.) Image process (Photoconductor/Developing/ Transfer/Cleaning) Data Operation data (Machine condition) Drum rotation time (sec) Developer rotation time (sec) Grid voltage correction value Developing bias correction value Laser power correction value Machine CRUM destination (1-9) CRUM destination (1-9)
Development adjustment registration value Humidity correction value Target value of humidity correction Temperature correction value Target value of temperature correction Environment correction value Target value of environment correction
Section Item
Operation/Procedure DRUM ROTATION TIME DEVE ROTATION TIME Vg1 - Vg4 Vb1 - Vb4 Ld1 - Ld4 DESTINATION 1 DESTINATION 2
SIMULATION 44-16 TONER CONTROL STANDARD LEVEL DISPLAY. HUMIDITY AREA: 11 INT HUMIDITY AREA: 7 TEMPERATURE AREA: 6 INT TEMPERATURE AREA: 6 TARGET LEVEL=DEV REF+HUM(TARGET)+TMP(TARGET)+LIFE(TARGET) 133 = 118 + 10(10) + 0(0) + 5(5)
46
46-2 Purpose Function (Purpose) Item Adjustment Used to adjust the copy density in all the copy modes (Auto, Text, Text/Photo, and Photo mode). Picture quality Density
SIMULATION 44-9 PROCESS CONTROL DATA DISPLAY. DRUM ROTATION TIME:01234567(sec) DEVE ROTATION TIME:01234567(sec) Vg1:30(V) Vg2:30(V) Vg3:30(V) Vg4:30(V) Vb1:30(V) Vb2:10(V) Vb3:30(V) Vb4:10(V) Ld1: 0 Ld2: 0 Ld3: 0 Ld4: 0 DESTINATION1:1 DESTINATION2:1
Operation/Procedure 1) Select the number corresponding to the copy mode to be adjusted with 10-key. (Select one of 3 - 6.)
44-14 Purpose Function (Purpose) Section Item Adjustment/Setup/Operation data output/Check (Display) Used to check the output level of the temperature sensor and the humidity sensor. Image process (Photoconductor/Developing) Operation
2) Press [START] key. 3) Enter the copy density level with 10-key. Item 0 1 2 3 4 5 6 Set range Default
Operation/Procedure The output levels of the temperature thermistor and the humidity thermistor in the developing unit are displayed. TH-DV HUS-DV Developing temperature thermistor Developing humidity thermistor 0 - 255 0 - 255
TRAY SELECT Paper feed tray selection COPY START Copy START (Default) EXP LEVEL Exposure level selection AE 3.0 AE mode 0 - 99 CH 3.0 Text mode 3.0 MIX 3.0 Text/Photo mode 3.0 PHOTO 3.0 Photo mode 3.0 The adjustment value is set.
50
When [START] key is pressed, copying is performed and the adjustment value is simultaneously set. Check the density of the printed copy image. Normal display ERROR display NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.
44-16 Purpose Function (Purpose) Section Item Adjustment/Setup/Operation data output/Check (Display) Used to check the toner concentration control data. Image process (Developing) Operation Humidity area Humidity area in development adjustment Temperature area Temperature area in development adjustment Toner control reference value
NOTE: When the copy image density is adjusted with this simulation, the copy image densities of all the copy modes are changed to the copy image density level set with this simulation. That is, the copy image density of each copy mode set with SIM 46-9, 10, 11 is changed to the copy image density level adjusted with this simulation. To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.)
Operation/Procedure HUMIDITY AREA INT HUMIDITY AREA TEMPERATURE AREA INT TEMPERATURE AREA TARGET LEVEL
3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
46-9 Purpose Function (Purpose) Adjustment Used to adjust the print density for each density level (display value) in the copy mode (binary Text mode). An optional print density can be set for each density level (display value). Picture quality Density
Item
Operation/Procedure 1) Select the number corresponding to the copy density adjustment level with 10-key. (Select one of 3 - 11.) 2) Press [START] key. 3) Enter the copy density level with 10-key. Item 0 1 2 3 4 5 6 7 8 9 10 11 TRAY SELECT COPY START EXP LEVEL 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Paper feed tray selection Copy START (Default) Exposure level selection Exposure level 1.0 Exposure level 1.5 Exposure level 2.0 Exposure level 2.5 Exposure level 3.0 Exposure level 3.5 Exposure level 4.0 Exposure level 4.5 Exposure level 5.0 Set Default range
NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When START key is pressed, the adjustment value is set and copying is performed.
SIMULATION 46-2 EXP. LEVEL SETUP (2). SELECT 0-6, AND PRESS START. 0. TRAY SELECT 1 1. COPY START 2. EXP LEVEL 1 3. AE 3.0 50 4. CH 3.0 50 5. MIX 3.0 50 6. PHOTO 3.0 50
0 - 99
50
SIMULATION 46-2 EXP. LEVEL SETUP (2). INPUT VALUE 0-99, AND PRESS START. 3. AE 3.0
50
4) Press [P] key or [START] key. The adjustment value is set. When [START] key is pressed, copying is perfumed and the adjustment value is set simultaneously.
Check the density of printed copy image. Normal display ERROR display Door open Jam Paper empty NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.
SIMULATION 46-2 EXP. LEVEL SETUP (2). SELECT 1-5, AND PRESS START. (FEED TRAY) 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT
Select 2, and press [START] key.
To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
SIMULATION 46-2 EXP. LEVEL SETUP (2). SELECT 3-6, AND PRESS START. (EXP. LEVEL SELECT) 3. AE 3.0 4. CH 3.0 5. MIX 3.0 6. PHOTO 3.0
NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When START key is pressed, the adjustment value is set and copying is performed.
manuals4you.com
46-10
SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). SELECT 0-11, AND PRESS START. 0. TRAY SELECT 1 1. COPY START 2. EXP LEVEL 1 3. 1.0 50 4. 1.5 50 5. 2.0 50 6. 2.5 50 7. 3.0 50 8. 3.5 50 9. 4.0 50 10. 4.5 50 11. 5.0 50
Item
Select other than 0 - 2, and press [START] key. Press [CUSTOM SETTINGS] key.
Adjustment Used to adjust the print density for each density level (display value) in the copy mode (binary Text/Photo mode). An optional print density can be set for each density level (display value). Picture quality
Operation/Procedure 1) Select the number corresponding to the copy density adjustment level with 10-key. (Select one of 3 - 11.) 2) Press [START] key. 3) Enter the copy density level with 10-key. Item Set range Default
SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). INPUT VALUE 0-99, AND PRESS START. 3. 1.0
50
SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). SELECT 1-5, AND PRESS START. (FEED TRAY) 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT
0 1 2 3 4 5 6 7 8 9 10 11
TRAY SELECT COPY START EXP LEVEL 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Paper feed tray selection Copy START (Default) Exposure level selection Exposure level 1.0 0 - 99 Exposure level 1.5 Exposure level 2.0 Exposure level 2.5 Exposure level 3.0 Exposure level 3.5 Exposure level 4.0 Exposure level 4.5 Exposure level 5.0
50
4) Press [P] key or [START] key. The adjustment value is set. When [START] key is pressed, copying is perfumed and the adjustment value is set simultaneously. Check the density of printed copy image. Normal display ERROR display Door open Jam Paper empty NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.
SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). SELECT 3-11, AND PRESS START. (EXP. LEVEL SELECT) 3. 1.0 4. 1.5 5. 2.0 6. 2.5 7. 3.0 8. 3.5 9. 4.0 10. 4.5 11. 5.0
To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When START key is pressed, the adjustment value is set and copying is performed.
46-11
SIMULATION 46-10 EXP. LEVEL SETUP (MIX.2). SELECT 0-11, AND PRESS START. 0. TRAY SELECT 1 1. COPY START 2. EXP LEVEL 1 3. 1.0 50 4. 1.5 50 5. 2.0 50 6. 2.5 50 7. 3.0 50 8. 3.5 50 9. 4.0 50 10. 4.5 50 11. 5.0 50
Item
Select other than 0 - 2, and press [START] key. Press [CUSTOM SETTINGS] key.
Adjustment Used to adjust the print density for each density level (display value) in the copy mode (binary Photo mode). An optional print density can be set for each density level (display value). Picture quality Density
Operation/Procedure 1) Select the number corresponding to the copy density adjustment level with 10-key. (Select one of 3 - 11.) 2) Press [START] key. 3) Enter the copy density level with 10-key. Item Set range Default
SIMULATION 46-10 EXP. LEVEL SETUP (MIX.2). INPUT VALUE 0-99, AND PRESS START. 3. 1.0
Select 1, and press [START] key.
50
SIMULATION 46-10 EXP. LEVEL SETUP (MIX.2). SELECT 1-5, AND PRESS START. (FEED TRAY) 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT
0 1 2 3 4 5 6 7 8 9 10 11
TRAY SELECT COPY START EXP LEVEL 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Paper feed tray selection Copy START (Default) Exposure level selection Exposure level 1.0 Exposure level 1.5 Exposure level 2.0 Exposure level 2.5 Exposure level 3.0 Exposure level 3.5 Exposure level 4.0 Exposure level 4.5 Exposure level 5.0
0 - 99
50
4) Press [P] key or [START] key. The adjustment value is set. When [START] key is pressed, copying is perfumed and the adjustment value is set simultaneously. Check the density of printed copy image. Normal display ERROR display Door open Jam Paper empty NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.
SIMULATION 46-10 EXP. LEVEL SETUP (MIX.2). SELECT 3-11, AND PRESS START. (EXP. LEVEL SELECT) 3. 1.0 4. 1.5 5. 2.0 6. 2.5 7. 3.0 8. 3.5 9. 4.0 10. 4.5 11. 5.0
To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When START key is pressed, the adjustment value is set and copying is performed.
manuals4you.com
The adjustment value is set. When [START] key is pressed, printing is perfumed and the adjustment value is set simultaneously. Check the density of printed image. Normal display ERROR display Door open Jam Paper empty NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.
Select other than 0 - 2, and press [START] key. Press [CUSTOM SETTINGS] key.
SIMULATION 46-11 EXP. LEVEL SETUP (PHOTO2). INPUT VALUE 0-99, AND PRESS START. 3. 1.0
50
NOTE: When the FAX print image density is adjusted with this simulation, the print image densities of all the FAX modes are changed to the image density level set with this simulation. That is, the print image density of each FAX mode set with SIM 46-13, 14, 15 is changed to the print image density level adjusted with this simulation. To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
SIMULATION 46-11 EXP. LEVEL SETUP (PHOTO2). SELECT 1-5, AND PRESS START. (FEED TRAY) 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT
SIMULATION 46-11 EXP. LEVEL SETUP (PHOTO2). SELECT 3-11, AND PRESS START. (EXP. LEVEL SELECT) 3. 1.0 4. 1.5 5. 2.0 6. 2.5 7. 3.0 8. 3.5 9. 4.0 10. 4.5 11. 5.0
NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When START key is pressed, the adjustment value is set and copying is performed.
SIMULATION 46-12 EXP.LEVEL SETUP FAX(AUTO SET). SELECT 0-2, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.FAX EXP.LEVEL 50
46-12 Purpose Function (Purpose) Item Adjustment Used to adjust the print density in the FAX mode (all modes). Picture quality
Operation/Procedure 1) Select the adjustment item of FAX EXP. LEVEL with 10-key. 2) Press [START] key. 3) Enter the print density level with 10-key. Item Set Default range
SIMULATION 46-12 EXP.LEVEL SETUP FAX(AUTO SET), INPUT VALUE 0-99, AND PRESS START. 2.FAX EXP.LEVEL
50
0 TRAY SELECT Paper feed tray selection 1 COPY START Copy START (Default) 2 FAX EXP. LEVEL FAX mode print density 0 - 99
50
Select 0, and press [START] key. Press [START] key, or press [CUSTOM SETTINGS] key.
SIMULATION 46-12 EXP.LEVEL SETUP FAX(AUTO SET).SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
46-13 Purpose Function (Purpose) Item Adjustment Used to adjust the print density in the FAX mode (each normal mode). (Only when FAX is installed.) Picture quality
SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL). SELECT 0-8, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50
Operation/Procedure 1) Select the number corresponding to one of the following adjustment items with 10-key. Manual mode (Print density adjustment level) Auto mode 2) Press [START] key. Set Default range 3) Enter the print density level with 10-key. Item 0 1 2 3 4 5 6 7 8 TRAY SELECT PRINT START EXP LEVEL AUTO 1.0 2.0 3.0 4.0 5.0 Paper feed tray selection Print start (Default) Exposure level selection Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5
Select other than 0 - 2, and press [START] key. Press [CUSTOM SETTINGS] key.
SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL),INPUT VALUE 0-99, AND PRESS START. 4.1.0
Select 1, Press [START] key. and press Press [CUSTOM SETTINGS] key, [START] key. or terminate copying.
50
0 - 99
50
4) Press [P] key or [START] key. The adjustment value is set. When [START] key is pressed, printing is perfumed and the adjustment value is set simultaneously. Check the density of printed image. Normal display ERROR display Door open Jam Paper empty NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.
SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL). SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT (ABOVE +20:DSPF MODE)
Select 2, and press [START] key.
To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL). SELECT 3-8, AND PRESS START. (EXP.LEVEL SELECT) 3.AUTO 4.1.0 5.2.0 6.3.0 7.4.0 8.5.0
When the sum of the above set value (1 - 5) and 20 is set, the mode is changed to the duplex print mode. NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When START key is pressed, the adjustment value is set and copying is performed.
manuals4you.com
46-14 Purpose Function (Purpose) Item Adjustment Used to adjust the print density in the FAX mode (each fine mode). (Only when FAX is installed.) Picture quality
SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE).SELECT 0-14,AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50 9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50 12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50
Select other than 0 - 2, and press [START] key.
Operation/Procedure 1) Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 3 - 14.) Normal mode (Print density adjustment level) Normal mode (Print density adjustment level) (Half-tone mode) Auto mode Auto mode (Half-tone mode) 2) Enter the print density level with 10-key. Item 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 TRAY SELECT PRINT START EXP LEVEL AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H) 2.0 (H) 3.0 (H) 4.0 (H) 5.0 (H) Set Default range
SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE),INPUT VALUE 0-99, AND PRESS START. 4.1.0
50
Paper feed tray selection Print start (Default) Exposure level selection Auto 0 - 99 Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)
Select 1, Press [START] key. and press Press [CUSTOM SETTINGS] key, [START] key. or terminate copying.
50
Select 0, and press [START] key.
SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE). SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
3) Press [P] key or [ATART] key. The entered value is set. When [START] key is pressed, printing is performed and the adjustment value is set simultaneously. Check the density of print image. Normal display ERROR display Door open Jam Paper empty NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.
SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE). SELECT 3-14, AND PRESS START. (EXP.LEVEL SELECT) 3.AUTO 4.1.0 5.2.0 6.3.0 7.4.0 8.5.0 9.AUTO(H) 10.1.0(H) 11.2.0(H) 12.3.0(H) 13.4.0(H) 14.5.0(H)
To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When START key is pressed, the adjustment value is set and copying is performed.
46-15 Purpose Function (Purpose) Item Adjustment Used to adjust the print density in the FAX mode (each super fine mode). (Only when FAX is installed.) Picture quality
SIMULATION 46-15 EXP.LEVEL SETUP FAX(SUPER FINE).SELECT 0-14,AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50 9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50 12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50
Operation/Procedure 1) Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 3 - 14.) Normal mode (Print density adjustment level) Normal mode (Print density adjustment level) (Half-tone mode) Auto mode Auto mode (Half-tone mode) 2) Press [START] key. 3) Enter the print density level with 10-key. Item 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 TRAY SELECT PRINT START EXP LEVEL AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H) 2.0 (H) 3.0 (H) 4.0 (H) 5.0 (H) Set Default range
SIMULATION 46-15 EXP.LEVEL SETUP FAX(SUPER FINE),INPUT VALUE 0-99, AND PRESS START. 2.AUTO
50
Paper feed tray selection Print start (Default) Exposure level selection Auto 0 - 99 Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)
50
Select 0, and press [START] key. Press [START] key, or press [CUSTOM SETTINGS] key.
SIMULATION 46-15 EXP.LEVEL SETUP FAX(SUPER FINE). SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
4) Press [P] key or [START] key. The entered value is set. When [START] key is pressed, printing is performed and the adjustment value is set simultaneously. Check the density of print image. Normal display ERROR display Door open Jam Paper empty NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.
SIMULATION 46-15 EXP.LEVEL SETUP FAX(SUPER FINE). SELECT 3-14, AND PRESS START. (EXP.LEVEL SELECT) 3.AUTO 4.1.0 5.2.0 6.3.0 7.4.0 8.5.0 9.AUTO(H) 10.1.0(H) 11.2.0(H) 12.3.0(H) 13.4.0(H) 14.5.0(H)
To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When START key is pressed, the adjustment value is set and copying is performed.
manuals4you.com
46-16 Purpose Function (Purpose) Item Adjustment Used to adjust the print density in the FAX mode (each ultra fine mode). (Only when FAX is installed.) Picture quality
SIMULATION 46-16 EXP.LEVEL SETUP FAX(ULTRA FINE).SELECT 0-14,AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50 9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50 12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50
Operation/Procedure 1) Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 3 - 14.) Normal mode (Print density adjustment level) Normal mode (Print density adjustment level) (Half-tone mode) Auto mode Auto mode (Half-tone mode) 2) Press [START] key. 3) Enter the print density level with 10-key. Item 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 TRAY SELECT PRINT START EXP LEVEL AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H) 2.0 (H) 3.0 (H) 4.0 (H) 5.0 (H) Set Default range
Select 1, and press [START] key.
SIMULATION 46-16 EXP.LEVEL SETUP FAX(ULTRA FINE),INPUT VALUE 0-99, AND PRESS START. 2.AUTO
50
Paper feed tray selection Print start (Default) Exposure level selection Auto 0 - 99 Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)
50
SIMULATION 46-16 EXP.LEVEL SETUP FAX(ULTRA FINE). SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
4) Press [P] key or [START] key. The entered value is set. When [START] key is pressed, printing is performed and the adjustment value is set simultaneously. Check the density of print image. Normal display ERROR display Door open Jam Paper empty NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY. 46-17
SIMULATION 46-16 EXP.LEVEL SETUP FAX(ULTRA FINE). SELECT 3-14, AND PRESS START. (EXP.LEVEL SELECT) 3.AUTO 4.1.0 5.2.0 6.3.0 7.4.0 8.5.0 9.AUTO(H) 10.1.0(H) 11.2.0(H) 12.3.0(H) 13.4.0(H) 14.5.0(H)
To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
Setting Used to set the gain in shading correction. Optical (Image scanning) Operation CCD, CIS
Operation/Procedure 1) Enter the number corresponding to the adjustment item 2) Press [START] key. 3) Enter the shading gain change value with 10-key. 4) Press [START] key. There is normally no need to change the shading gain with this simulation. Only when the scanned image density is unsatisfactory though shading is performed, the above procedure is performed. 1 2 3 Item CCD ODD CCD EVEN CIS Set range 0 - 255 Default 112 128
NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When START key is pressed, the adjustment value is set and copying is performed.
Exposure level
SIMULATION 46-17 CCD/CIS SHADING GAIN DATA SETUP. SELECT 1-3, AND PRESS START. 1.CCD ODD 112 2.CCD EVEN 112 3.CIS 128
SIMULATION 46-17 CCD SHADING GAIN DATA SETUP. INPUT VALUE 0-255,AND PRESS START. 1.CCD ODD
112
46-18 Purpose Function (Purpose) Item Adjustment Used to adjust the gamma (density gradient) in the copy mode. Picture quality Density
3 4 5 6 7 8 9 10 11 12 13 14
AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H) 2.0 (H) 3.0 (H) 4.0 (H) 5.0 (H)
Item Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)
4) Press [START] key. Normal display ERROR display Door open Jam Paper empty NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.
Operation/Procedure (Copy mode selection) 1) Select the number corresponding to the copy mode to be adjusted with 10-key. (Select one of 3 - 14.) 2) Press [START] key. (Print mode selection in the FAX mode) 1) Enter 2 with 10-key. 2) Press [START] key. 3) Select the number corresponding to one of the following adjustment items. (Select one of 3 - 14.) Normal mode (Print density adjustment level) Normal mode (Print density adjustment level) (Half-tone mode) Auto mode Auto mode (Half-tone mode) Item 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 TRAY SELECT PRINT START EXP LEVEL OC_AE OC_CHARA OC_MIX OC_PHOTO SPF1_AE SPF1_CHARA SPF1_MIX SPF1_PHOTO SPF2_AE SPF2_CHARA SPF2_MIX SPF2_PHOTO CIS_AE CIS_CHARA CIS_MIX CIS_PHOTO Set Default range (Gamma adjustment)
After completion of the above procedures, perform the following procedures. 1) Enter the gamma level with 10-key. 2) Enter [P] key or [CUSTOM SETTINGS] key. When [START] key is pressed, printing is performed and the adjustment value is set simultaneously. Check the gamma density (copy density in the low density area and the high density area) of printed copy image. The greater the adjustment value is, the greater the gamma value is, resulting in a higher contrast. (Copy condition setting in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.)
Paper feed tray selection Print start (Default) Exposure level selection AE mode (OC) 0 - 127 Text mode (OC) Text/Photo mode (OC) Photo mode (OC) AE mode (SPF1) Text mode (SPF1) Text/Photo mode (SPF1) Photo mode (SPF1) AE mode (SPF2) Text mode (SPF2) Text/Photo mode (SPF2) Photo mode (SPF2) AE mode (CIS) Text mode (CIS) Text/Photo mode (CIS) Photo mode (CIS)
64
1 2 3 4 5
NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When START key is pressed, the adjustment value is set and copying is performed.
manuals4you.com
1 2 3 4
AE MODE AE STOP MODE (COPIER) AE STOP MODE (SCANNER) AE STOP MODE (FAX) Set value 1 Item
AE mode AE fixed mode (Copier) AE fixed mode (Scanner) AE fixed mode (FAX) Default 2
Mode AE mode
2
SIMULATION 46-18 GAMMA SETUP. INPUT VALUE 0-127, AND PRESS START. 3.OC_AE
64
AE fixed mode
0 1
Image quality priority mode (Normal mode) Gamma is sharp to provide high contrast images. Toner consumption priority mode Gamma is mild to provide low contrast images. AE fixed OFF AE fixed ON
AE fixed OFF: The automatic density (exposure) control is performed in real time. (The density level is changed in real time according to the document pattern.) AE fixed ON: The density at the lead edge of the document is scanned, and the overall density (exposure) level is determined according to the scanned density level. (Overall density level fixed)
SIMULATION 46-19 EXP.MODE SETUP. SELECT 1-4, AND PRESS START. 1.AE MODE 2 2.AE STOP MODE(COPIER) 1 3.AE STOP MODE(SCANNER)0 4.AE STOP MODE(FAX) 0
Select 1, and press [START] key.
SIMULATION 46-18 GAMMA SETUP(COPIER). SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
SIMULATION 46-18 GAMMA SETUP(COPIER). SELECT 3-14, AND PRESS START. (EXP.LEVEL SELECT) 3.AUTO 4.1.0 5.2.0 6.3.0 7.4.0 8.5.0 9.AUTO(H) 10.1.0(H) 11.2.0(H) 12.3.0(H) 13.4.0(H) 14.5.0(H)
SIMULATION 46-19 EXP.MODE SETUP. INPUT VALUE 1-2, AND PRESS START. 1.AE MODE
1
Select 2, 3, or 4 and press [START] key.
SIMULATION 46-19 EXP.MODE SETUP. INPUT VALUE 0-1, AND PRESS START. 2.AE STOP MODE(COPIER)
46-19 Purpose Function (Purpose) Item Adjustment Used to set the auto mode operation specifications in each mode (copy, scan, FAX). Picture quality Density
Operation/Procedure (Toner save operation YES/NO setting in the auto mode) 1) Select "1. AE MODE" with 1-key. 2) Press [START] key. 3) Select the number corresponding to the operation specifications with 10-key. 4) Press [START] key. When [START] key is pressed, the adjustment value is set. (Operation setting in the auto copy mode) 1) Select the number corresponding to the mode with 10-key. (Select one of 2 - 4.) 2) Press [START] key. 3) Select the number corresponding to the operation mode with 10-key.
46-20 Purpose Function (Purpose) Adjustment Used to adjust the copy density correction in the SPF copy mode for the document table copy mode. The adjustment is made so that the copy density becomes the same as that of the document table copy mode. SPF Picture quality Density
SIMULATION 46-20 OC/SPF EXP. ADJUSTMENT. SELECT 1-4, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.SPF(ODD) 128 4.SPF(EVEN) 128 5.DSPF 128
Section Item
Select other than 0 - 2, and press [START] key. Press [CUSTOM SETTINGS] key.
Operation/Procedure (Adjustment mode selection) 1) Select the number corresponding to the copy mode to be adjusted with 10-key. SPF odd pixel (Front surface copy), SPF even pixel (Front surface copy), SPF (Back surface copy) (Select one of 3 - 5.) 2) Press [SATART] key. (Copy density level adjustment) 1) Enter the density correction value with 10-key. 2) Press [P] key or [START] key. (Copy condition setting in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.) NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When START key is pressed, the adjustment value is set and copying is performed. Item Content Set Default range
SIMULATION 46-20 OC/SPF EXP. ADJUSTMENT. INPUT VALUE 0-255, AND PRESS START. 3.SPF(ODD)
128
NOW PRINTING.
Press [START] key or press [CUSTOM SETTINGS] key.
SIMULATION 46-20 OC/SPF EXP. ADJUSTMENT. SELECT 1-5, AND PRESS START. (FEED TRAY) 2.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
SIMULATION 46-20 OC/SPF EXP. ADJUSTMENT. SELECT 3-8, AND PRESS START. (EXP. LEVEL SELECT) 3.1.0 4.1.5 5.2.0 6.2.5 7.3.0 8.3.5 9.4.0 10.4.5 11.5.0
46-21 Purpose Function (Purpose) Item Adjustment Used to adjust the scanner exposure level in all the scanner modes. Picture quality Density
0 TRAY SELECT Paper feed tray selection 1: TRAY1 2: TRAY2 3: TRAY3 4: TRAY4 5: Manual feed 1 PRINT START Print start (Default) 2 EXP LEVEL Exposure level selection 3: Exposure level 1.0 4: Exposure level 1.5 5: Exposure level 2.0 6: Exposure level 2.5 7: Exposure level 3.0 8: Exposure level 3.5 9: Exposure level 4.0 10: Exposure level 4.5 11: Exposure level 5.0 3 SPF (ODD) SPF (front) (odd pixel) 4 SPF (EVEN) SPF (front) (even pixel) 5 DSPF DSPF (Back surface)
Operation/Procedure 1) Select "SCANNER EXP. LEVEL" with 10-key. 2) Press [START] key. 3) Enter the image density adjustment value. 4) Press [P] key or [START] key. NOTE: When this simulation is performed to adjust the scan image densities, all the image densities in all the scan modes are changed to the image density level set with this simulation. That is, the image densities set with SIM 46-22, 23, 24, 25, and 45 are changed to the image density level set with this simulation. Set Default range 0 SCANNER EXP. LEVEL Image density level 0 - 99 50 Item 0 - 255 128 NOTE: Only the set value is changed and no printing is performed.
"Set value - 128" is added to the shading adjustment value (SIM 46-17).
manuals4you.com
46-23
SIMULATION 46-21 EXP.LEVEL SETUP SCANNER(AUTO SET), PRESS START. 0.SCANNER EXP.LEVEL 50
Adjustment Used to adjust the scanner exposure level in the fine text mode. Picture quality Density
Operation/Procedure 1) Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 0 - 11.) Normal mode (Image density adjustment level) Normal mode (Image density adjustment level) (Half-tone mode) Auto mode Auto mode (Half-tone mode) 2) Press [START] key. 3) Enter the image density adjustment value with 10-key.
SIMULATION 46-21 EXP.LEVEL SETUP SCANNER(AUTO SET), INPUT VALUE 0-99, AND PRESS START. 0.SCANNER EXP.LEVEL
50
46-22 Purpose Function (Purpose) Item Adjustment Used to adjust the scanner exposure level in the normal text mode. Picture quality Density
4) Press [START] key or press [P] key. The adjustment value is set. Item 0 1 2 3 4 5 6 7 8 9 10 11 AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H) 2.0 (H) 3.0 (H) 4.0 (H) 5.0 (H) Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone) Set range 0 - 99 Default 50
Operation/Procedure 1) Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 0 - 5.) Normal mode (Image density adjustment level) Auto mode 2) Press [START] key. 3) Enter the image density adjustment value with 10-key. 4) Press [START] key or press [CUSTOM SETTINGS] key. The adjustment value is set. Item 0 1 2 3 4 5 AUTO 1.0 2.0 3.0 4.0 5.0 Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Set range 0 - 99 Default 50
SIMULATION 46-23 EXP.LEVEL SETUP SCANNER(FINE). INPUT VALUE 0-99, AND PRESS START. 0.AUTO
50
SIMULATION 46-22 EXP.LEVEL SETUP SCANNER(NORMAL), INPUT VALUE 0-99, AND PRESS START. 0.AUTO
50
46-24 Purpose Function (Purpose) Item Adjustment Used to adjust the scanner exposure level (in the super fine text mode). Picture quality Density
46-25 Purpose Function (Purpose) Item Adjustment Used to adjust the scanner exposure level in the ultra fine text mode. Picture quality Density
Operation/Procedure 1) Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 0 - 11.) Normal mode (Image density adjustment level) Normal mode (Image density adjustment level) (Half-tone mode) Auto mode Auto mode (Half-tone mode) 2) Press [START] key. 3) Enter the image density adjustment value with 10-key. 4) Press [START] key or press [P] key. The adjustment value is set. Item 0 1 2 3 4 5 6 7 8 9 10 11 AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H) 2.0 (H) 3.0 (H) 4.0 (H) 5.0 (H) Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone) Set range 0 - 99 Default 50
Operation/Procedure 1) Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 0 - 11.) Normal mode (Image density adjustment level) Normal mode (Image density adjustment level) (Half-tone mode) Auto mode Auto mode (Half-tone mode) 2) Press [START] key. 3) Enter the image density adjustment value with 10-key. 4) Press [START] key or press [P] key. The adjustment value is set. Item 0 1 2 3 4 5 6 7 8 9 10 11 AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H) 2.0 (H) 3.0 (H) 4.0 (H) 5.0 (H) Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone) Set range 0 - 99 Default 50
SIMULATION 46-24 EXP.LEVEL SETUP SCANNER(SUPER FINE). INPUT VALUE 0-99, AND PRESS START. 0.AUTO
50
SIMULATION 46-25 EXP.LEVEL SETUP SCANNER(ULTRA FINE). INPUT VALUE 0-99, AND PRESS START. 0.AUTO
50
manuals4you.com
46-27 Purpose Function (Purpose) Item Adjustment Used to adjust the gamma (density gradient) of the network scanner mode. Picture quality 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 OC_AE OC_CHARA OC_MIX OC_PHOTO SPF1_AE SPF1_CHARA SPF1_MIX SPF1_PHOTO SPF2_AE SPF2_CHARA SPF2_MIX SPF2_PHOTO CIS_AE CIS_CHARA CIS_MIX CIS_PHOTO
Item AE mode (OC) Text mode (OC) Text/Photo mode (OC) Photo mode (OC) AE mode (SPF1) Text mode (SPF1) Text/Photo mode (SPF1) Photo mode (SPF1) AE mode (SPF2) Text mode (SPF2) Text/Photo mode (SPF2) Photo mode (SPF2) AE mode (CIS) Text mode (CIS) Text/Photo mode (CIS) Photo mode (CIS)
Default 3
Operation/Procedure (Scanner mode selection) 1) Select the number corresponding to the scanner mode to be adjusted with 10-key. (Select one of 1 - 9.) 2) Press [START] key. (Gamma adjustment) 1) Enter the gamma level with 10-key. 2) Press [START] key. The greater the adjustment value is, the greater the gamma is, resulting in a higher contrast. Item 1 OC_Fine.HT 2 OC_SFine.HT 3 OC_UFine.HT 4 SPF1_Fine.HT 5 SPF1_SFine.HT 6 SPF1_UFine.HT 7 SPF2_Fine.HT 8 SPF2_SFine.HT 9 SPF2_UFine.HT 10 CIS_Fine.HT 11 CIS_SFine.HT 12 CIS_UFine.HT Fine text (Half-tone) (OC) Super fine (Half-tone) (OC) Ultra fine (Half-tone) (OC) Fine text (Half-tone) (SPF1) Super fine (Half-tone) (SPF1) Ultra fine (Half-tone) (SPF1) Fine text (Half-tone) (SPF2) Super fine (Half-tone) (SPF2) Ultra fine (Half-tone) (SPF2) Fine text (Half-tone) (CIS) Super fine (Half-tone) (CIS) Ultra fine (Half-tone) (CIS) Set Default range 0 - 127 64
SPF1: DSPF front surface (CCD) SPF2: DSPF back surface (CCD)
SIMULATION 46-31 SHARPNESS LEVEL SETUP. SELECT 1.OC_AE 3 2.OC_CHARA 3 4.OC_PHOTO 3 5.SPF1_AE 3 7.SPF1_MIX 3 8.SPF1_PHOTO 10.SPF2_CHARA 3 11.SPF2_MIX 13.CIS_AE 3 14.CIS_CHARA 16.CIS_PHOTO 3
SIMULATION 46-31 SHARPNESS LEVEL SETUP. INPUT VALUE 0-3, AND PRESS START. 1.OC_AE
46-39
SIMULATION 46-27 GAMMA SETUP(SCANNER). SELECT 1-12, AND PRESS START. 1.OC_Fine.HT 64 2.OC_SFine.HT 64 3.OC_UFine.HT 4.SPF1_Fine.HT 64 5.SPF1_SFine.HT 64 6.SPF1_UFine.HT 7.SPF2_Fine.HT 64 8.SPF2_SFine.HT 64 9.SPF2_UFine.HT 10.CIS_Fine.HT 64 11.CIS_SFine.HT 64 12.CIS_UFine.HT
64 64 64 64
Operation/Procedure 1) Enter the sharpness level with 10-key. 2) Press [START] key. The greater the adjustment value is, the greater the sharpness is.
46-31 Purpose Function (Purpose) Item Adjustment Used to adjust sharpness of the copy mode. Picture quality
Operation/Procedure (Copy mode selection) 1) Select the number corresponding to the copy mode to be adjusted with 10-key. (Select one of 1 - 16.) 2) Press [START] key. (Sharpness adjustment) 1) Enter the sharpness level with 10-key. 2) Press [START] key. The greater the adjustment value is, the greater the sharpness is.
SIMULATION 46-39 FAX SHARPNESS LEVEL SETUP. SELECT 1-12, AND PRESS START. 1:OC_NORMAL 3 2:OC_FINE 3 3:OC_FINE(H) 1 4:OC_SFINE 3 5:OC_SFINE(H) 1 6:OC_UFINE 3 7:OC_UFINE(H) 1 8:OC_600 3 9:OC_600(H) 3 10:SPF1_NORMAL 3 11:SPF1_FINE 3 12:SPF1_FINE(H) 1 13:SPF1_SFINE 3 14:SPF1_SFINE(H) 1 15:SPF1_UFINE 3 16:SPF1_UFINE(H) 1 17:SPF1_600 3 18:SPF1_600(H) 1 19:SPF2_NORMAL 3 20:SPF2_FINE 3 21:SPF2_FINE(H) 1 22:SPF2_SFINE 3 23:SPF2_SFINE(H) 1 24:SPF2_UFINE 3 25:SPF2_UFINE(H) 1 26:SPF2_600 3 27:SPF2_600(H) 1 28:CIS_NORMAL 3 29:CIS_FINE 3 30:CIS_FINE(H) 1 31:CIS_SFINE 3 32:CIS_SFINE(H) 1 33:CIS_UFINE 3 34:CIS_UFINE(H) 1 35:CIS_600 3 36:CIS_600(H) 1
SIMULATION 46-45 EXP.LEVEL SETUP FAX(600dpi). SELECT 0-14, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50 9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50 12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50
Select other than 0 - 2, and press [START] key.
SIMULATION 46-45 EXP.LEVEL SETUP FAX(600dpi),INPUT VALUE 0-99,AND PRESS START. 2.AUTO
50
SIMULATION 46-39 FAX SHARPNESS LEVEL SETUP. INPUT VALUE 1-3, AND PRESS START. 1:OC_NORMAL
NOW PRINTING.
Press [START] key, or press [CUSTOM SETTINGS] key.
46-45 Purpose Function (Purpose) Item Adjustment Used to adjust the image density in the FAX mode (600dpi). Picture quality
Operation/Procedure 1) Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 0 - 11.) Normal mode (Image density adjustment level) Normal mode (Image density adjustment level) (Half-tone mode) Auto mode Auto mode (Half-tone mode) 2) Press [START] key. 3) Enter the image density adjustment value with 10-key. 4) Press [START] key or press [P] key. The adjustment value is set. Item 0 1 2 3 4 5 6 7 8 9 10 11 AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H) 2.0 (H) 3.0 (H) 4.0 (H) 5.0 (H) Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone) Set range 0 - 99 Default 50 46-46
SIMULATION 46-45 EXP.LEVEL SETUP FAX(600dpi). SELECT 1-5,AND PRESS START. (FEED TRAY) 3.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5:BPT
SIMULATION 46-45 EXP. LEVEL SETUP FAX(600dpi). SELECT 3-8,AND PRESS START. (EXP. LEVEL SELECT) 3.AUTO 4.1.0 5.2.0 6.3.0 7.4.0 8.5.0 9.AUTO(H) 10.1.0(H) 11.2.0(H) 12.3.0(H) 13.4.0(H) 14.5.0(H)
Operation/Procedure 1) Enter the sharpness level with 10-key. 2) Press [START] key. The greater the adjustment value is, the greater the sharpness is. Set range: 1 - 3 Default: 3 (Normal), 1 (Halftone)
manuals4you.com
1) Select the number corresponding to the copy magnification ratio adjustment mode to be adjusted with 10-key. (Select one of 3 - 7.) 2) Press [START] key. 3) Enter the copy magnification ratio adjustment value with 10key. 4) Press [P] key or [START] key. When the [START] key is pressed, copying is performed and the adjustment value is set simultaneously. The copy magnification ratio in the sub scan direction can be adjusted by changing the scan speed (motor RPM). Normal display ERROR display Door open Jam Paper empty NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.
SIMULATION 46-46 SCANNER SHARPNESS LEVEL SETUP. INPUT VALUE 1-3, AND PRESS START. 1:OC_NORMAL
The greater the value is, the greater the correction is. One step corresponds to 0.1% adjustment. (Copy condition setting in this simulation) To select paper (paper feed tray), perform the following procedures.
48
48-1 Purpose Function (Purpose) Section Item Adjustment Used to adjust the copy magnification ratio (in the main scanning and the sub scanning directions). Optical (Image scanning) Picture quality
1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray of the selected paper with 10-key. (Select one of 1 - 5.) 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
Operation/Procedure (Adjustment mode selection) 1) Select the number corresponding to the copy mode to be adjusted with 10-key. (Select one of 3 - 7.) 2) Press [START] key. 0 1 2 3 Item Set range Default TRAY SELECT Paper feed tray 1-5 selection COPY START Copy START (Default) MAGNIFICATION Print magnification 25 - 400% ratio CCD (MAIN) SCAN main scanning 0 - 99 50 magnification ratio adjustment (CCD) CCD (SUB) SCAN sub scanning magnification ratio adjustment (CCD) SPF (MAIN) SPF front surface magnification ratio adjustment (Main scan) SPF (SUB) SPF front surface magnification ratio adjustment (Sub scan) CIS (MAIN) SPF back surface magnification ratio adjustment (CIS main scan)
manuals4you.com
When the total of the above set value (1 - 5) and 10 is entered, the mode is changed to the duplex mode. The copy magnification ratio can be set with the following 1) Enter 2 with 10-key. 2) Press [START] key. 3) Enter the copy magnification ratio with 10-key. 4) Press [START] key. Set range 25 - 400%
NOTE: When [P] key is pressed after entering the adjustment value, the adjustment value is set. When [START] key is pressed instead, the adjustment value is set and copying is performed.
SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 4.CCD(SUB)
50
SIMULATION 48-5 SCAN MOTOR SPEED ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 0.MIR(220)
50
48-6 Purpose Function (Purpose) Item Adjustment HSYNC cycle adjustment Picture quality
SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 1-15, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)
Operation/Procedure (Adjustment mode selection) 1) Select the number corresponding to the HSYNC cycle to be adjusted with 10-key. (Select one of 3.) 2) Press [START] key.
Item 0 1 2 3 TRAY SELECT COPY START MAGNIFICATION CIS Paper feed tray selection Copy START (Default) Print magnification ratio CIS HSYNC cycle Set range 25 - 400 40 - 60 Default 50
100
(HSYNC cycle adjustment) 48-5 Purpose Function (Purpose) Section Item Adjustment Used to adjust the copy magnification ratio in the sub scanning direction. Optical (Image scanning) Picture quality 1) Select the number corresponding to the HSYNC cycle to be adjusted with 10-key. (Select one of 3.) 2) Press [START] key. 3) Enter the HSYNC cycle adjustment value with 10-key. 4) Press [START] key. When the [START] key is pressed, copying is performed and the adjustment value is set simultaneously. Normal display ERROR display Door open Jam Paper empty NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.
Operation/Procedure When the sub scanning direction image magnification ratio adjustment with SIM 48-1 cannot provide a satisfactory result if a different magnification ration is set and a copy is made, perform this simulation. When there is an error in the copy magnification ratio in reduction copy, change the adjustment value of the high speed mode. When there is an error in the copy magnification ratio in enlargement copy, change the adjustment value of the low speed mode. 1) Select the number corresponding to the adjustment mode with 10-key. 2) Press [START] key. 3) Enter the copy adjustment value with 10-key. The scanner/SPF motor rotation sped adjustment value is entered. Item 0 1 2 3 4 5 MIR (220) MIR (169) MIR (110) MIR (55) SPF (220) SPF (110) Content Mirror motor (220mm/sec) Mirror motor (168.7mm/sec) Mirror motor (110mm/sec) Mirror motor (55mm/sec) SPF motor (220mm/sec) SPF motor (110mm/sec) Set range 0 - 99 Default 50
(Copy condition setting in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray of the selected paper with 10-key. (Select one of 1 - 5.) 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
When the total of the above set value (1 - 5) and 10 is entered, the mode is changed to the duplex mode.
manuals4you.com
The copy magnification ratio can be set with the following 1) Enter 2 with 10-key. 2) Press [START] key. 3) Enter the copy magnification ratio with 10-key. 4) Press [START] key. Set range 25 - 400%
Set LEAD to 15. (Enter 15 as the adjustment value of LEAD, and press [P] key.) (0.1mm/step) Set DENA to 35. (Enter 35 as the adjustment value of DENA, and press [P] key.) (0.1mm/step) 2) Make a copy at the normal ratio (100%) and check the lead edge void area and the image loss. (Enter 100 as the set value of the copy magnification ratio (MAGNIFICATION), and press [START] key.) 3) If the adjustment result is not satisfactory, perform the following procedures. If the lead edge void are is not 3.5mm: Change the adjustment value of RRCB and perform the adjustment. (Change the adjustment value of RRCB and press [START] key.) (1msec/step) If the lead edge image loss is not 1.5mm: Change the adjustment value of RRCA and perform the adjustment. (Change the adjustment value of RRCA and press [START] key.) (Shift for the adjustment value change: 0.2mm/step) (Rear edge void area adjustment) Adjust so that the rear edge void area is 3.5mm. (Change the adjustment value of TRAIL EDGE, and press [START] key.) (Front/rear frame direction image loss adjustment) Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment value of SIDE, and press [P] key.) When the adjustment value is changed, the image position is shifted in the front/rear frame direction.
SIMULATION 48-6 HSYNC CYCLE ADJUSTMENT. SELECT 0-3, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100 3.CIS 50
Select other than 0 - 2, and press [START] key.
SIMULATION 48-6 HSYNC CYCLE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 3.CIS
50
(Front/rear frame direction void area adjustment) Adjust so that the total of the front/rear direction void areas is 7.0mm. (Change the adjustment values of FRONT/REAR, and press [START] key.) Front frame void area = 3.5mm Rear frame void area = 3.5mm If, as shown above, the front and the rear void areas are not even, use SIM 50-5 to adjust the image off-center position. Item 0 TRAY SELECT Content Set range 1-5 25 400% 0 - 99 Default
SIMULATION 48-6 HSYNC CYCLE ADJUSTMENT. SELECT 1-15, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT (ABOVE+10: DUPLEX MODE)
100
50
50-1 Purpose Function (Purpose) Adjustment Used to adjust the copy image position and the void area (image loss) adjustment on print paper in the copy mode. (The similar adjustment can be performed with SIM 50-5 and 50-2 (Simplified method).) (Document table mode) Picture quality Image position
Item
Operation/Procedure (Lead edge image loss/void area adjustment) 1) Set the lead edge image loss adjustment value (LEAD EDGE) and the paper lead edge void adjustment value (DENA) as follows. (Standard set value) Lead edge image loss: 1.5mm (LEDA: 15) Paper lead edge void: 3.5mm (DENA: 35)
Paper feed tray selection 1 COPY START Copy START (Default) 2 MAGNIFICATION Print magnification ratio (Lead edge adjustment value) 3 RRCA Document scan start position 4 RRCB Resist roller clutch ON timing adjustment value 10 SIDE2 ADJ. Correction value for RRCB when refereeing from ADU (Image loss set value) 5 LEAD Lead edge image loss set value 6 SIDE Side image loss set value (Void set value) 7 LEAD_EDGE Lead edge void set (DENA) value 8 TRAIL_EDGE Rear edge void (DENB) adjustment value 9 FRONT/REAR Front/Rear void adjustment value
50
1 - 99
50
0 - 99
15 20
0 - 99
35
32
NOTE: When [P] is pressed after entering an adjustment value, the adjustment value is set. When [START] key is pressed instead, the adjustment value is set and copying is performed.)
50-2 Purpose Function (Purpose) Adjustment Used to adjust the document scan position, the image print position, and the void area (image loss). (Simple adjustment) (This adjustment is the simple method of SIM 50-1.) (Document table mode) Picture quality Image position
(Copy condition in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray of the target paper with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed Item
Operation/Procedure (Lead edge image loss/void area adjustment) 1) Set the RRGB value of SIM 50-1 to 80 - 99. 2) Set the lead edge image loss adjustment value (LEAD EDG) and the paper lead edge void adjustment value (DENA) to the values specified below. (Standard set value) Lead edge image loss: 1.5mm Paper lead edge void: 3.5mm (DENA: 35) Set the adjustment value of LEAD to 15. (Enter 15 as the adjustment value of LEAD and press [P] key. Set the adjustment value of DENA to 35. (Enter 35 as the adjustment value of DENA and press [P] key.) 3) Set the adjustment value of L1 to 0. (Enter 0 as the adjustment value of L1, and press [P] key.) 4) Set the adjustment value of L2 to 0. (Enter 0 as the adjustment value of L2, and press [P] key.) 5) Make a copy at 400%, and calculate the values of L1 and L2. (Enter 100 as the set value (MAGNIFICATION) of the copy magnification ratio, and press [START] key.) (Place a scale on the document table and make a copy.)
To set the magnification ratio, perform the following procedure. 1) Enter 2 with 10-key. 2) Press [START] key. 3) Enter the copy magnification ratio with 10-key. 4) Press [START] key. Set range 25 - 400 (%)
SIMULATION 50-1 LEAD EDGE ADJUSTMENT. SELECT 0-9, AND 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100 (ADJUSTMENT DATA) 3.RRCA 50 4.RRCB 50 (IMAGE LOSS SETTING) 5.LEAD 15 6.SIDE (VOID SETTING) 7.LEAD_EDGE(DENA) 35 8.TRAIL_EDGE(DENB) 35
PRESS START.
2
10.SIDE2 ADJ. 50 20 9.FRONT/REAR 32
L1 = Distance (mm) from the image lead edge position to the scale position of 10mm x 10 L2 = Distance (mm) from the image lead edge position to the paper lead edge x 10 6) Enter the above values as the set values of L1 and L2. (Enter the adjustment values of L1 and L2, and press [P] key.) If the adjustment result is not satisfactory, perform the above procedures again from the beginning, or use SIM 50-1 to adjust. NOTE: If a satisfactory result is not obtained with the above procedures, through the adjustment values are changed individually, the normal adjustment cannot be made. Perform procedures 3) to 6) continuously. (Rear edge void area adjustment) Adjust so that the rear edge void area is 3.5mm. (Change the adjustment value of TRAIL EDGE, and press [START] key.) (Front/rear frame direction image loss adjustment) Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment value of SIDE, and press [P] key.)
Select other than 0 - 2, and press [START] key. Press [CUSTOM SETTINGS] key.
SIMULATION 50-1 LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 3.RRCA
Press [START] key. Select 1, and press [START] key. Press [CUSTOM SETTINGS] key, or terminate copying.
50
When this adjustment value is changed, the image position is shifted in the front/rear frame direction. (Front/rear frame direction void area adjustment) Adjust so that the total of the front/rear direction void areas is 7.0mm. (Change the adjustment values of FRONT/REAR, and press [START] key.) Front frame void area = 3.5mm Rear frame void area = 3.5mm If, as shown above, the front and the rear void areas are not even, use SIM 50-5 to adjust the image off-center position.
SIMULATION 50-1 LEAD EDGE ADJUSTMENT. SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
Select 2, and press [START] key.
100
manuals4you.com
Content
Paper feed tray selection 1 COPY START Copy START (Default) 2 MAGNIFICATION Print magnification ratio (Lead edge adjustment value) 3 L1 Distance from the image lead edge to the scale of 10mm. (Platen 400%, 0.1mm increment) 4 L2 Distance from the paper lead edge to the image lead edge (0.1mm increment) (Image loss set value) 5 LEAD Lead edge image loss set value 6 SIDE Side image loss set value (Void set value) 7 LEAD_EDGE Lead edge void set (DENA) value 8 TRAIL_EDGE (DENB) 9 FRONT/REAR Rear edge void adjustment value Front/Rear void adjustment value
Default 400
SIMULATION 50-2 LEAD EDGE ADJUSTMENT(CALC). SELECT 0-9, AND PRESS START. 0. TRAY SELECT 1 1.COPY START 2. MAGNIFICATION 400 (ADJUSTMENT) 3.LT 320 4.L2 105 (IMAEG LOSS SETTING) 5.LEAD 15 6.SIDE 20 (VOID SETTING) 7.LEAD_EDGE(DENA) 35 8.TRAIL_EDGE(DENB) 35 9.FRONT/REAR 32
Select other than 0 - 2, and press [START] key. Press [CUSTOM SETTING] key.
SIMULATION 50-2 LEAD EDGE ADJUSTMENT(CALC). INPUT VALUE 0-99, AND PRESS START. 3.L1
320
0 - 99
15 20
Press [CUSTOM SETTING] key, or terminate copying.
0 - 99
35
SIMULATION 50-2 LEAD EDGE ADJUSTMENT(CALC). SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
Select 2, and press [START] key.
32
Press [START] key, or press [CUSTOM SETTINGS] key.
NOTE: When [P] is pressed after entering an adjustment value, the adjustment value is set. When [START] key is pressed instead, the adjustment value is set and copying is performed.) Normal display ERROR display Door open Jam Paper empty NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.
100
50-5 Purpose Function (Purpose) Adjustment Used to adjust the print image position and the void area (image loss) on print paper. (Adjustment as the print engine) (This adjustment is reflected on all the FAX/printer/copy modes.) Picture quality
(Copy condition in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray of the target paper with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
Item
Operation/Procedure (Print image off-center position adjustment) 1) Enter the number corresponding to the paper feed tray to be adjusted with 10-key. (Select one of 9 - 14.) (Table 1) 2) Press [START] key. 3) Enter the adjustment value with 10-key. 4) Press [P] key or [START] key. When [START] key is pressed, the adjustment value is set and printing is performed. (Table 2) Check the off-center of the self-print patter of print-out. (Shift for the adjustment value change: 0.1mm/step) The greater the adjustment value is, the more the print image is shifted to the front. (Lead edge void area adjustment) 1) Set the lead edge void adjustment value (DENA) as specified below. (Standard set value) Paper lead edge void: 3.5mm (DENA: 35) Set the adjustment value of DENA to 35. Enter 35 as the adjustment value of DENA, and press [P] key.
To set the magnification ratio, perform the following procedure. 1) Enter 2 with 10-key. 2) Press [START] key. 3) Enter the copy magnification ratio with 10-key. 4) Press [START] key. Set range 25 - 400 (%)
2) Check the lead edge void area on the self print pattern. (Enter 1 and press [START] key.) 3) If the adjustment result is not satisfactory, perform the following procedures. If the lead edge void area is not 3.5mm: Change the adjustment value of RRCB and perform the adjustment. (Change the adjustment value of RRCB and press [START] key.) (Shift for the adjustment value change: 0.1mm/step) (Front/rear frame direction void area adjustment) Adjust so that the total of the front/rear direction void areas is 7.0mm. (Change the adjustment values of FRONT/REAR, and press [START] key.) Front frame void area = 3.5mm (Paper resist adjustment) 1) Enter the number corresponding to the paper feed tray to be adjusted with 10-key. (Select one of 3 - 9.) (Table 1) 2) Press [START] key. 3) Enter the adjustment value with 10-key. 4) Press [P] key or [START] key. When [START] key is pressed, the adjustment value is set and printing is performed. (Table 2) If the relative positions of paper and print images vary or a paper jam occurs, change the adjustment value. (Print condition setting in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. (Select one of 1 - 5.)(Table 3) 4) Press [START] key. (The paper feed tray is selected.) When the total of the above set value (1 - 5) and 10 is entered, the mode is changed to the duplex print mode. NOTE: When [P] key is pressed after entering the adjustment value in this simulation, the adjustment value is set. When [START] key is pressed instead, the adjustment value is set and copying is performed. (Table 1) Default Set ARARrange M351U/ M451U/ M355U M455U 1-5 50
Select 1, and press [START] key. Press [START] key.
Item
(Off-center set value) Self print 9 T1 Tray 1 adjustment 0 - 99 10 T2 Tray 2 adjustment 11 T3 Tray 3 adjustment 12 T4 Tray 4 adjustment 13 BPT Manual feed tray adjustment 14 ADU Adjustment when paper is fed again from ADU (Void set value) 15 LEAD_EDGE Lead edge void set 0 - 99 (DENA) value 16 TRAIL_EDGE Rear edge void (DENB) adjustment value 17 FRONT/REAR Front/Rear void adjustment value (Table 2) Normal display ERROR display Door open Jam Paper empty
35
32
(Table 3) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
SIMULATION 50-5 LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START (ADJUSTMENT DATA) LEAD EDGE: 2.RRCB 50 3.SIDE2 ADJ. 50 RESIST: 4.T1 50 5.T2 50 6.DESK 50 7.BPT 50 8.ADU 50 OFF CENTER: 9.T1 50 10.T2 50 11.T3 50 12.T4 50 13.BPT 50 14.ADU 50 (VOID SETTING) 15.LEAD_EDGE(DENA) 35 16.TRAIL_EDGE(DENB) 35
Item
17.FRONT/REAR 32
Select other than 0 - 1, and press [START] key. Press [CUSTOM SETTINGS] key.
0 TRAY SELECT Paper feed tray selection 1 PRINT START Print start (Default) (Lead edge adjustment value) 2 RRCB Resist roller clutch 0 - 99 ON timing adjustment value 3 SIDE2 ADJ. Correction value for RRCB when refereeing from ADU (Resist adjustment value) 4 T1 Tray 1 adjustment 0 - 99 5 T2 Tray 2 adjustment 6 DESK Tray 4 adjustment 7 BPT Manual feed tray adjustment 8 ADU Adjustment when paper is fed again from ADU
SIMULATION 50-5 LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 2.RRCB
50
50
65 55 55 60 55
60 50 50 55 50
SIMULATION 50-5 LEAD EDGE ADJUSTMENT. SELECT 1-15, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT (ABOVE+10: DUPLEX MODE)
manuals4you.com
50-6 Purpose Function (Purpose) Adjustment Used to adjust the copy image position and void area (image loss) on print paper in the copy mode. (The similar adjustment can be performed with SIM 50-7 (simple method).) (SPF mode) Picture quality
4) Press [START] key. (The paper feed tray is selected.) To set the copy magnification ratio, perform the following procedure. 1) Enter 2 with 10-key. 2) Press [START] key. 3) Enter the copy magnification ratio with 10-key. 4) Press [START] key. Set range (Table 1) Item 0 1 2 TRAY SELECT COPY START Paper feed tray selection Copy START (Default) Set Default range 1-5 25 200% 0 - 99 25 - 200 (%)
Item
Operation/Procedure (Lead edge image loss adjustment) (Table 1) 1) Set the front and back surface image loss adjustment values (LEAD EDGE) as specified below: (Standard set value) Lead edge image loss: 1.5mm (LEAD: 1.5)Paper lead edge: 3.5mm (DENA: 35) Set the adjustment value of LEAD to 15. (Enter 15 as the adjustment value of LEAD EDGE, and press [P] key.) 2) Make a duplex copy at 100% with the SPF, and check that the lead edge (image loss) is 1.5mm either on the front surface and the back surface. (Select the duplex mode in the paper selection mode of SIM 50-6.) (Table 3) (Enter 100 as the copy magnification ratio set value (MAGNIFICATION), and press [START] key.) If the adjustment result is not satisfactory, perform the following procedures: 3) Change the adjustment values of SIDE1 and SIDE2, and perform the adjustment. (Change the adjustment values of SIDE1 and SIDE2, and press [START] key.) SIDE1: SPF front surface document lead edge scan position adjustment value SIDE2: SPF back surface document lead edge scan position adjustment value (Shift for the adjustment value change: 0.1mm/step) (The image scan start timing is determined with the detection timing of the document lead edge by the detector SPPD.) Repeat procedures 2) and 3) until a satisfactory result is obtained. (Rear edge image loss adjustment) 1) Use the SPF at 100% to make a duplex copy, and check that the rear edge image loss is 1.5mm on the front and the back surfaces. (Select the duplex mode in the paper selection mode of SIM 50-6.) (Enter 100 as the copy magnification ratio set value (MAGNIFICATION), and press [START] key.) If the adjustment value is not satisfactory, perform the following procedure. 2) Change the adjustment value of TRAIL EDGE. Change the adjustment value of TRAIL EDGE, and press [START] key. Repeat the above procedures until a satisfactory result is obtained. (Front/rear frame direction image loss adjustment) Set the adjustment value of the front surface and the back surface (FRONT/REAR) to 20. (Enter 20 as the adjustment value of FRONT/REAR, and press [P] key.) When the adjustment value is changed, the image position is shifted in the front/rear frame direction. NOTE: When [P] key is pressed after entering the adjustment value, the adjustment value is set. When [START] key is pressed instead, the adjustment value is set and copying is performed. (Table 2) (Copy condition setting in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. (Table 3) 9 8
(Lead edge adjustment value) 3 SIDE1 Front surface document scan start position adjustment value Back surface document scan start position adjustment value Front surface lead edge image loss set value Front surface side edge image loss set value Front surface rear edge image loss set value Back surface lead edge image loss set value Back surface side edge image loss set value Back surface rear edge image loss set value 0 - 20 0 - 20 0 - 99 15 20 0 50
SIDE2
(Table 3) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
When the total of the above set value and 10 is entered, the mode is changed to the duplex mode (DD), and a duplex copy is made.
50-7
SIMULATION 50-6 LEAD EDGE ADJUSTMENT(SPF). SELECT 0-10, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100 (ADJUSTMENT DATA)3.SIDE1 50 4.SIDE2 50 (IMAGE LOSS SETTING) SIDE1: 5.LEAD_EDGE 15 6.FRONT/REAR 20 7.TRAIL_EDGE 0 SIDE2: 8.LEAD_EDGE 15 9.FRONT/REAR 20 10.TRAIL_EDGE 0
Select other than 0 - 2, and press [START] key. Press [CUSTOM SETTING] key.
Item
Adjustment Used to adjust the copy image position and void area (image loss) on print paper in the copy mode. (The similar adjustment can be performed with SIM 50-6.) (SPF mode) Picture quality
Operation/Procedure (Lead edge image loss adjustment) 1) Set the front and back surface image loss adjustment values (LEAD EDGE) as specified below: (Standard set value) Lead edge image loss: 1.5mm (LEAD: 1.5)Paper lead edge void: 3.5mm (DENA: 35) Set the adjustment value of LEAD to 15. (Enter 15 as the adjustment value of LEAD EDGE, and press [P] key.) 2) Set the adjustment value of L4 to 0. (Enter 0 as the adjustment value of L4, and press [P] key. 3) Set the adjustment value of L5 to 0. (Enter 0 as the adjustment value of L5, and press [P] key. 4) Make a copy at 200% with the SPF, and calculate the values of L4 and L5. (Enter 200 as the set value of the copy magnification ratio set value (MAGNIFICATION) and press [START] key.) L4 = Distance (mm) from the image lead edge position to the scale of 10mm x 10 L5 = Distance (mm) from the image lead edge position to the paper lead edge x 10 5) Enter the above values as the set values of L4 and L5. (Enter the adjustment values of L4 and L5, and press [P] key.) (The image scan start timing is determined with the detection timing of the document lead edge by the detector SPPD.) If the adjustment result is not satisfactory, perform the above procedures again or adjust with SIM 50-1. NOTE: If the adjustment result of the above procedures is not satisfactory, though the adjustment value is changed individually, the adjustment cannot be completed normally. Repeat procedures 2) - 6) until a satisfactory result is obtained. (Rear edge image loss adjustment) Adjust so that the rear edge image loss is 3.5mm. (Change the adjustment value of TRAIL EDGE, and press [START] key.) (Front/rear frame direction image loss adjustment) Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment value of SIDE, and press [P] key.) When the adjustment value is changed, the image position is shifted in the front/rear frame direction. NOTE: When [P] key is pressed after entering the adjustment value, the adjustment value is set. When [START] key is pressed instead, the adjustment value is set and copying is performed. (Table 2) (Copy condition setting in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. (Table 3) 4) Press [START] key. (The paper feed tray is selected.) To set the copy magnification ratio, perform the following procedure. 1) Enter 2 with 10-key. 2) Press [START] key. 3) Enter the copy magnification ratio with 10-key.
SIMULATION 50-6 LEAD EDGE ADJUSTMENT(SPF). INPUT VALUE 0-99, AND PRESS START. 3.SIDE1
50
SIMULATION 50-6 LEAD EDGE ADJUSTMENT(SPF). SELECT 1-15, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT (ABOVE+10: DUPLEX MODE)
Select 2, and press [START] key.
100
manuals4you.com
4) Press [START] key. Set range (Table 1) Item 0 TRAY SELECT Set range 1-5 Default 25 - 200 (%)
SIMULATION 50-7 LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 0-10, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 200
(ADJUSTMENT DATA) 3.L4 160 4.L5 160 (IMAGE LOSS SETTING) SIDE1: 5.LEAD_EDGE 15 6.FRONT/REAR 20 7.TRAIL_EDGE 0 SIDE2: 8.LEAD_EDGE 15 9.FRONT/REAR 20 10.TRAIL_EDGE 0
Select other than 0 - 2, and press [START] key. Press [CUSTOM SETTING] key.
Paper feed tray selection 1 COPY START Copy START (Default) 2 MAGNIFICATION Print magnification 25 ratio 200% (Lead edge adjustment value) 3 L4 Distance from the 0 - 999 front surface image lead edge to the scale of 10mm (SPF: 200%) 4 L5 Distance from the back surface image lead edge to the scale of 10mm (SPF: 200%) (Image loss set value: SIDE 1) 5 LEAD_EDGE Front surface lead 0 - 99 edge image loss set value 6 FRONT_REAR Front surface side edge image loss set value 7 TRAIL_EDGE Front surface rear 0 - 20 edge image loss set value (Image loss set value: SIDE 2) 8 LEAD_EDGE Back surface lead 0 - 99 edge image loss set value 9 FRONT/REAR Back surface side edge image loss set value 10 TRAIL_EDGE Back surface rear 0 - 20 edge image loss set value (Table 2) Normal display ERROR display Door open Jam Paper empty
SIMULATION 50-7 LEAD EDGE ADJUSTMENT(SPF CALC.). INPUT VALUE 0-99, AND PRESS START. 3.L4
50
15
Select 0, and press [START] key. Press [START] key or press [CUSTOM SETTINGS] key.
20
SIMULATION 50-7 LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 1-15, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
15
20
100
50-10 NOW COPYING. DOOR OPEN. JAM PAPER EMPTY. Purpose Function (Purpose) Item Adjustment Used to adjust the print image off-center position. (Adjusted separately for each paper feed section.) Picture quality Image position
Operation/Procedure (Print image off-center position adjustment) NOTE: This simulation cannot provide an accurate adjustment. Do not use. 1) Enter the number corresponding to the number of the paper feed tray to be adjusted with 10-key. (Select one of 3 - 9.) Item Set range Default Paper feed tray 1-5 selection 1 COPY START Copy START (Default) 2 MAGNIFICATION Print magnification 25 - 400% 100 ratio (Off-center adjustment value) 3 TRAY1 Tray 1 adjustment 0 - 99 50 4 TRAY2 Tray 2 adjustment 5 TRAY3 Tray 3 adjustment 6 TRAY4 Tray 4 adjustment 7 BPT Manual feed tray adjustment 8 ADU Adjustment when paper is fed again from ADU 0 TRAY SELECT
(Table 3) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
When the total of the above set value and 10 is entered, the mode is changed to the duplex mode (DD), and a duplex copy is made.
2) Press [START] key. 3) Enter the adjustment value with 10-key. 4) Press [P] key or [START] key. When [START] key is pressed, the adjustment value set and copying is performed. Normal display ERROR display Door open Jam Paper empty NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.
SIMULATION 50-10 PRINT OFF-CENTER ADJUSTMENT. SELECT 0-8, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100 (ADJUSTMENT DATA) 3.TRAY1 50 4.TRAY2 50 5.TRAY3 50 6.TRAY4 50 7.BPT 50 8.ADU 50
Select other than 0 - 2, and press [START] key.
(Image off-center adjustment) 1) Enter 1 with 10-key. 2) Press [START] key. The adjustment pattern is printed. 3) Check the off-center of the printed image. (UNIT: 0.1mm/step When the adjustment value is increased, the print image is shifted to the front direction.) NOTE: This adjustment can be performed with SIM 50-5. (Copy condition setting in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. (Select one of 1 - 5) 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed 50-12
SIMULATION 50-10 PRINT OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 2.TRAY1
Select 1, and press [START] key.
50
SIMULATION 50-10 PRINT OFF-CENTER ADJUSTMENT. SELECT 1-15, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT (ABOVE+10: DUPLEX MODE)
When the total of the above set value (1 - 5) and 10 is entered, the mode is changed to the duplex print mode. To set the copy magnification ratio, perform the following procedure. 1) Enter 2 with 10-key. 2) Press [START] key. 3) Enter the copy magnification ratio with 10-key. 4) Press [START] key. Set range 25 - 400 (%)
Adjustment Used to adjust the scan image off-center position. (Adjusted separately for each scan mode.) Picture quality Image position
Operation/Procedure (Select the scan mode to be adjusted.) 1) Enter the number corresponding to the scan mode to be adjusted with 10-key. (Select one of 3 - 5.) Item Paper feed tray selection 1 COPY START Copy START (Default) 2 MAGNIFICATION Print magnification ratio (Resist adjustment value) 3 PLATEN OC mode adjustment 4 SPF SIDE1 SPF front surface adjustment 5 SPF SIDE2 SPF back surface adjustment 0 TRAY SELECT 2) Press [START] key. Set range 1-5 25 - 400% Default 100
NOTE: When [P] key is pressed after entering the adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.
0 - 99
50
manuals4you.com
(Scan off-center position adjustment) 1) Enter the scan image position adjustment value with 10-key. 2) Press [P] key or [START] key. When [START] key is pressed, the adjustment value is set and copying is performed. Normal display ERROR display Door open Jam Paper empty NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.
SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100 (ADJUSTMENT DATA) 3.PLATEN 50 4.SPF SIDE1 50 5.SPF SIDE2 50
Select other than 0 - 2, and press [START] key. Press [CUSTOM SETTINGS] key.
Check the off-center of the printed image. Repeat the above procedures until a satisfactory result is obtained. (UNIT: 0.1mm/step When the adjustment value is increased, the print image is shifted to the front direction.) (Copy condition setting in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. (Select one of 1 - 6) 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
Select 0, and press [START] key. Press [START] key or press [CUSTOM SETTINGS] key.
SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 3.PLATEN
50
SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 1-15, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT (ABOVE+10: DUPLEX MODE)
When the total of the above set value (1 - 5) and 10 is entered, the mode is changed to the duplex print mode. To set the copy magnification ratio, perform the following procedure. 1) Enter 2 with 10-key. 2) Press [START] key. 3) Enter the copy magnification ratio with 10-key. 4) Press [START] key. Set range 25 - 400 (%)
100
50-27 Purpose Function (Purpose) Item Adjustment Used to adjust the image loss of the scan image in the FAX/scan mode. Picture quality
NOTE: When [P] key is pressed after entering the adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.
Operation/Procedure (Select the scan mode to be adjusted.) 1) Enter the number corresponding to the adjustment item with 10-key. 2) Press [START] key. 3) Enter the adjustment value with 10-key. 4) Press [START] key. (Shift for the adjustment value change: 1.0mm/step) Item FAX send 1 2 3 4 5 6 7 8 9 OC (LEAD_EDGE) OC (FRONT/REAR) OC (TRAIL_EDGE) SPF (LEAD_EDGE) OC lead edge OC side OC rear edge SPF lead edge 0 - 10 3 (Unit 1mm) (3mm) Set range Default
SPF (FRONT/REAR) SPF side SPF (TRAIL_EDGE) SPF rear edge CIS (LEAD_EDGE) CIS (TRAIL_EDGE) CIS lead edge CIS rear edge CIS (FRONT/REAR) CIS side
Item Scanner mode 10 OC (LEAD_EDGE) 11 OC (FRONT/REAR) 12 OC (TRAIL_EDGE) 13 SPF (LEAD_EDGE) OC lead edge OC side OC rear edge SPF lead edge
Set range
Default Item
14 SPF (FRONT/REAR) SPF side 15 SPF (TRAIL_EDGE) SPF rear edge 16 CIS (LEAD_EDGE) 18 CIS (TRAIL_EDGE) CIS lead edge CIS rear edge 17 CIS (FRONT/REAR) CIS side
SIMULATION 50-27 ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND PRESS START. [FAX] 1.OC(LEAD_EDGE) 0 2.OC(FRONT/REAR) 0 3.OC(TRAIL_EDGE) 0 4.SPF(LEAD_EDGE) 0 5.SPF(FRONT/REAR) 0 6.SPF(TRAIL_EDGE) 0 7.CIS(LEAD_EDGE) 0 8.CIS(FRONT/REAR) 0 9.CIS(TRAIL_EDGE) 0 [SCN] 10.OC(LEAD_EDGE) 0 11.OC(FRONT/REAR) 0 12.OC(TRAIL_EDGE) 0 13.SPF(LEAD_EDGE) 0 14.SPF(FRONT/REAR) 0 15.SPF(TRAIL_EDGE) 0 16.CIS(LEAD_EDGE) 0 17.CIS(FRONT/REAR) 0 18.CIS(TRAIL_EDGE) 0
0 TRAY SELECT Paper feed tray selection 1 PRINT START Copy start (Initial value) 2 TRAY1 Tray 1 resist 0 - 99 adjustment value 3 TRAY2 Tray 2 resist adjustment value 4 DESK Desk resist adjustment value 5 BPT Manual tray resist adjustment value 6 ADU ADU resist adjustment value 7 SPF (HIGH) SPF resist adjustment value (High speed) 8 SPF (LOW) SPF resist adjustment value (Low speed) 2) Press [START] key.
75
75
2) Press [START] key. When [START] key is pressed, the adjustment value is set and paper feed and copying are performed. Normal display ERROR display Door open Jam Paper empty NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.
51
51-2 Purpose Function (Purpose) Adjustment Used to adjust the contact pressure of paper on the resist roller of each section (each paper feed, duplex feed and SPF paper feed of the copier). (This adjustment is required when the print image position variations are considerably great or when paper jams occur frequently.) Paper transport (Discharge/Switchback/Transport) Operation
(Copy condition setting in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Enter 0 with 10-key. 2) Press [START] key. (The mode is changed to the paper feed tray selection mode.) 3) Enter the number corresponding to the paper feed tray to be used with 10-key. 4) Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 TRAY1 TRAY2 TRAY3 TRAY4 BPT TRAY1 TRAY2 TRAY3 TRAY4 Manual feed
Section Item
Operation/Procedure (Select the scan mode to be adjusted.) 1) Enter the number corresponding to the paper feed tray to be adjusted with 10-key. (Select one of 2 - 12.)
When the total of the above set value (1 - 5) and 10 is entered, the mode is changed to the duplex print mode. NOTE: When [P] key is pressed after entering the adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.
manuals4you.com
SIMULATION 51-2 RESIST TIMING ADJUSTMENT. SELECT 0-8, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.TRAY1 60 3.TRAY2 50 4.DESK 50 5.BPT 55 6.ADU 50 7.SPF(HIGH) 60 8.SPF(LOW) 75
SIMULATION 53-6 SPF TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START. 1.MAX.POSITION 2.POSITION 1 3.POSITION 2 4.MIN.POSITION
Select 1, and press [START] key.
SIMULATION 51-2 RESIST TIMING ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 2.TRAY1
60
SIMULATION 53-6 SPF TRAY ADJUSTMENT. MAX.POSITION ... COMPLETE (or ERROR)
SIMULATION 53-6 SPF TRAY ADJUSTMENT. POSITION 1 ... COMPLETE (or ERROR)
SIMULATION 51-2 RESIST TIMING ADJUSTMENT. SELECT 1-15, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT (ABOVE+10: DUPLEX MODE)
SIMULATION 53-6 SPF TRAY ADJUSTMENT. POSITION 2 ... COMPLETE (or ERROR)
Select 4, and press [START] key. Press [CUSTOM SETTINGS] key.
SIMULATION 53-6 SPF TRAY ADJUSTMENT. MIN.POSITION ... COMPLETE (or ERROR)
53
53-6 Purpose Function (Purpose) Section Item Adjustment Used to adjust the DSPF width detection level.
53-7 Purpose Function (Purpose) Section Item Adjustment/Setup/Operation data output/Check (Display/Print) Used to enter the SPF width detection adjustment value. DSPF Operation
Operation
Operation/Procedure 1) Enter the number corresponding to the set item with 10-key. 1 2 3 4 Item Set range Default MAX. POSITION Max. width 0 - 1023 66 POSITION 1 Adjustment position 1 456 POSITION 2 Adjustment position 2 713 MIN. POSITION Min. width 791
Operation/Procedure 1) Set the SPF paper feed guide to the max. position. 2) Select "MAX. POSITION" with 10-key. 3) Press [START] key. The max. width detection level is recognized. 4) Press [CSUTOM SETTING] key. 5) Set the SPF paper feed guide to A4R size position. 6) Select POSITION 1 with 10-key. 7) Press [START] key. The A4R width detection level is recognized. 8) Press [CSUTOM SETTING] key. 9) Set the SPF paper feed guide to A5R size position. 10) Select POSITION 2 with 10-key. 11) Press [START] key. The A5R width detection level is recognized. 12) Press [CSUTOM SETTING] key. 13) Set the SPF paper feed guide to the min. position. 14) Select "MIN. POSITION" with 10-key. 15) Press [START] key. The min. width detection level is recognized. If the above procedures are not completed normally, ERROR is displayed. When completed normally, COMPLETE is displayed.
2) Press [START] key. 3) Enter the set value with 10key. 4) Press [START] key.
SIMULATION 53-7 SPF TRAY ADJUSTMENT(MANUAL). SELECT 1-4, AND PRESS START. 1.MAX.POSITION: 66 2.POSITION 1 : 456 3.POSITION 2 : 713 4.MIN.POSITION: 791
SIMULATION 53-7 SPF TRAY ADJUSTMENT(MANUAL). INPUT VALUE 0-1023, AND PRESS START. 1.MAX.POSITION
66
53-8 Purpose Function (Purpose) Adjustment Used to adjust the document scan start position. (Used to adjust the scanner scan position in the SPF mode front scan.)
55
55-1 Purpose Function (Purpose) Section Item Setting Used to set the specifications of the engine control operations. (PCU PWB) Operation Specifications
Operation/Procedure (Automatic adjustment) 1) Select 1 or 2 with 10-key. 2) Press [START] key. (Manual feed adjustment) 1) Enter the adjustment value with 10key. 2) Press [START] key. When an adjustment error occurs, the trouble code (E7-17) is displayed simultaneously with COMPLETED. Item 1 2 AUTO MANUAL Automatic adjustment Manual feed adjustment (Direct entry of a number) Set range 1 - 70 (1 count: 0.1mm) Default 32
Operation/Procedure This simulation is used to change and check the engine soft SW. Set this setting to the default. There is no need to change this setting in the market.
SIMULATION 55-1 ENGINNE SOFT SW. SETTING. SELECT 1-16, AND PRESS START.
1
Press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
SIMULATION 53-8 SPF SCANNING POSITION ADJUSTMENT. PRESS START. 1.AUTO 2.MANUAL. 25
SIMULATION 55-1 ENGINNE SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS START. 1 2 3 4 5 6 7 8 SOFT SW-1:
00001001
Select 2, and press [START] key. Select 1, and press [START] key. Press [CUSTOM SETTINGS] key.
55-2
SIMULATION 53-8 SPF SCANNING POSITION ADJUSTMENT EXECUTING.... 1. AUTO
Trouble occurrence
Setting Used to set the specifications of the scanner control operations. (Scanner control PWB) Operation Specifications
Operation/Procedure
SIMULATION 53-8 SPF SCANNING POSITION ADJUSTMENT COMPLETED. 1. AUTO
This simulation is used to change and check the scanner soft SW. Set this setting to the default. There is no need to change this setting in the market.
1
SIMULATION 55-2 SCANNER SOFT SW. SETTING. SELECT 1-16, AND PRESS START.
<Trouble occurrence>
SIMULATION 53-8 TROUBLE !! (E7-17) SPF SCANNING POSITION ADJUSTMENT COMPLETED. 1. AUTO
1
Press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
SIMULATION 53-8 SPF SCANNING POSITION ADJUSTMENT. INPUT VALUE 1-70, AND PRESS START. 2. MANUAL
SIMULATION 55-2 SCANNER SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS START. 1 2 3 4 5 6 7 8 SOFT SW-1:
00001001
25
manuals4you.com
55-3 Purpose Function (Purpose) Section Item Setting Used to set the specifications of the controller operations. (MFP control PWB) Operation Specifications
3) The confirmation menu is opened to confirm YES/NO of data transfer. Select one. 1 2 YES NO Data transfer is executed. Data transfer is not executed.
4) Press [START] key. After completion of transfer, the transfer result is displayed. If there is no error, the machine is automatically reset after completion of data transfer. If there is an error, "NG" is displayed. (The machine is not reset.) When restoring from HDD, fit the configurations of the Flash ROM and the optional Flash ROM at back-up.
SIMULATION 56-1 DATA COPY. SELECT 1-7, AND PRESS START. 1.ALL(EEPROM,SRAM,FlashROM) HDD 2.HDD ALL(EEPROM,SRAM,FlashROM) 3.EEPROM HDD 4.HDD EEPROM 5.SRAM(+FAX Memory,+Option Memory) HDD 6.HDD SRAM(+FAX Memory,+Option Memory) 7.FontROM HDD
Press [START] key.
Operation/Procedure This simulation is used to change and check the controller soft SW. Set this setting to the default. There is no need to change this setting in the market.
SIMULATION 55-3 MFP SOFT SW. SETTING. SELECT 1-16, AND PRESS START.
1
Press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
SIMULATION 55-3 MFP SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS START. 1 2 3 4 5 6 7 8 SOFT SW-1:
00001001
56
56-1 Purpose Function (Purpose) Section Item Data transfer Used to transfer the MFP controller data. (Used to repair the PWB.) MFP controller Data transfer
SIMULATION 56-1 EEPROM HDD DATA COPY. ARE YOU SURE?. 1. YES 2. NO
Operation/Procedure 1) Select the number corresponding to the data transfer mode with 10-key. 1 ALL (EEPROM, SRAM, FlashROM) HDD HDD ALL (EEPROM, SRAM, FlashROM) EEPROM HDD HDD EEPROM SRAM (+ FAX Memory, + Option Memory) HDD All the contents of memory are transferred to HDD. (Similar to execution of items 3 and 5.) The HDD contents are transferred to all the memories. (Similar to execution of items 4 and 6.) Transfer from EEPROM to HDD Transfer from HDD to EEPROM Transfer from SRAM to HDD. When, however, the FAX memory or an option memory (for FAX memory) * is installed, the contents of the Fax memory are also transferred to HDD. Transfer from HDD to SRAM. When, however, the FAX memory or an option memory (for FAX memory) * is installed, the contents HDD are transferred to the FAX memory as well as the SRAM. Transfer from the font ROM to HDD
60
60-1 Purpose Function (Purpose) Section Item Operation test/Check Used to check the MFP control (DRAM) operations (read/write). ICU Operation
3 4 5
Operation/Procedure 1) Enter the number corresponding to the memory to be checked with 10-key. 1 2 MFP DRAM ASIC DRAM ERDH image memory ASIC image memory
2) Press [START] key. The memory read/write operation is started. After starting the operation, "NOW CHECKING" is displayed during checking. When read/write is normally completed, "OK" is displayed. If an error occurs, "NG" is displayed.
7 *:
FontROM HDD
When Flash ROM or OP_Flash ROM is not installed, transfer is not made.
61-2
SIMULATION 60-1 DRAM TEST. SELECT 1-2, AND PRESS START. 1. ICU DRAM 2. ASIC DRAM
Adjustment Used to adjust the laser power (absolute value) in the copy mode. Scanner (write) unit (LSU) Operation
Operation/Procedure 1) Select the number corresponding to the adjustment mode with 10-key. Default AR-M351U/ AR-M451U/ M355U M455U 1 AE Auto exposure 67 - 150 76 93 mode 2 CHARA. Text mode 3 MIX Text/Photo mode 4 PHOTO Photo mode Item Set range 2) Press [START] key. 3) Enter the adjustment value with 10-key. 4) Enter [START] key.
Check completion
61
61-1 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of the scanner (write) unit (LSU). Scanner (write) unit (LSU) Operation
NOTE: Be sure to set the default value. If not, a trouble may occur in the LSU.
SIMULATION 61-2 LASER POWER SETTING(COPY). SELECT 1-4, AND PRESS START. 1.AE 93 2.CHARA. 93 3.MIX 93 4.PHOTO 93
Operation/Procedure Used to check if the LSU delivers output of the sync signal (HSYNC/) or not. "NOW CHECKING" is displayed during checking. When the test is normally completed, "OK" is displayed. If an error occurs, "NG" is displayed.
SIMULATION 61-1 LSU TEST. PRESS START. 1. LSU SIMULATION 61-2 LASER POWER SETTING(COPY). INPUT VALUE 67-150, AND PRESS START. 1.AE
93
61-3
1
Press [CUSTOM SETTINGS] key.
Adjustment Used to adjust the laser power (absolute value) in the FAX mode. Scanner (write) unit (LSU) Operation
Operation/Procedure
SIMULATION 61-1 LSU TEST. NOW CHECKING 1. LSU
1) Select the number corresponding to the adjustment mode with 10-key. 2) Press [START] key. 3) Enter the adjustment value with 10-key. Set range Default 67 - 150 76 (AR-M351U/M355U) 93 (AR-M451U/M455U)
Check completion
4) Enter [START] key. NOTE: Be sure to set the default value. If not, a trouble may occur in the LSU.
manuals4you.com
1
Press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
SIMULATION 61-3 LASER POWER SETTING(FAX). INPUT VALUE 67-150, AND PRESS START. 1.FAX
110
Completion
61-4 Purpose Function (Purpose) Section Item Adjustment Used to adjust the laser power (absolute value) in the printer mode. Scanner (write) unit (LSU) Operation
62-2 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of the hard disk (read/ write). (Only in the model with a disk installed) (Partial check) MFP controller (HDD) Operation
Operation/Procedure 1) Select the number corresponding to the adjustment mode with 10-key. 2) Press [START] key. 3) Enter the adjustment value with 10-key. Set range Default 67-150 76 (AR-M351U/M355U) 93 (AR-M451U/M455U)
Operation/Procedure 1) Select YES/NO of hard disk read/write check. 1 2 YES NO Execution Cancel
4) Enter [START] key. NOTE: Be sure to set the default value. If not, a trouble may occur in the LSU.
SIMULATION 61-4 LASER POWER SETTING(PRINTER). PRESS START. 1.PRINTER 100
2) Press [START] key. During testing, "EXECUTING" is displayed. When test is completed normally, "OK" is displayed. If not, "NG" is displayed.
SIMULATION 62-2 HDD R/W TEST. ARE YOU SURE? 1. YES 2. NO
1
Press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
SIMULATION 61-4 LASER POWER SETTING(PRINTER). INPUT VALUE 67-150, AND PRESS START. 1.PRINTER
100
Completion
62
62-1 Purpose Function (Purpose) Section Item Data clear Used to format the hard disk. (Only in the model with a disk installed) MFP controller (HDD) Clear
2) Press [START] key. During formatting, "EXECUTING" is displayed. When formatting is completed normally, "OK" is displayed. If not, "NG" is displayed. AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 67
an
l ua
ou y 4
o .c
62-3 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of the hard disk (read/ write). (Only in the model with a disk installed) (All areas check) MFP controller (HDD) Operation
SIMULATION 62-6 SMART OFFLINE TEST. 1. SHORT SELF-TEST 2. EXTENDED SELF-TEST
Operation/Procedure 1) Select YES/NO of hard disk read/write check. 1 2 YES NO Execution Cancel
2) Press [START] key. During testing, "EXECUTING" is displayed. When test is completed normally, "OK" is displayed. If not, "NG" is displayed.
SIMULATION 62-3 HDD R/W TEST(ALL). ARE YOU SURE? 1. YES 2. NO
Completion Press [CUSTOM SETTINGS] key.
* = SHORT SELF-TEST, EXTENDED SELF-TEST 62-7 Purpose Function (Purpose) Operation test/Check Used to check the operations of the hard disk. (The result of the self diag operation of the SMART function is printed out.) (Only in the model with a disk installed) MFP controller (HDD) Clear
Completion
Section Item
0 1
2) Press [START] key. 62-6 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operations of the hard disk. (The self diag operation of the SMART function is executed.) (Only in the model with a disk installed) MFP controller (HDD) Clear The result of the hard disk operation check (the self diag operation of the SMART function) is printed out.
SIMULATION 62-7 SMART ERROR LOG PRINT OUT. SELECT SETTING, AND PRESS START. 0. TRAY SELECT :AUTO ONLY 1. PRINT START
Operation/Procedure 1) Select the number corresponding to the self diag check mode. 1 2 SHORT SELF-TEST EXTENDED SELF-TEST Partial test All areas test
Select 1 and press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
2) Press [START] key. During the self diag operation, "EXECUTING" is displayed. If the self diag is completed normally, "0" is displayed. If not, any value but 0 is displayed.
SIMULATION 62-7 SMART ERROR LOG PRINT OUT. EXECUTING 0. TRAY SELECT :1
manuals4you.com
62-8 Purpose Function (Purpose) Section Item Data clear Used to format the hard disk (the system area excluded). (Only in the model with a disk installed) MFP controller (HDD) Clear
SIMULATION 62-10 JOB COMPLETE DATA CLEAR. (WITH JOB LOG DATA) ARE YOU SURE? 1.YES 2.NO
Operation/Procedure 1) Select YES/NO of hard disk (the system area excluded) format. 1 2 YES NO Execution Cancel
SIMULATION 62-10 JOB COMPLETE DATA CLEAR. (WITH JOB LOG DATA) EXECUTING.
2) Press [START] key. During formatting, "EXECUTING" is displayed. When formatting is completed normally, "OK" is displayed. If not, "NG" is displayed.
SIMULATION 62-8 HDD FORMAT (EXCEPT SYSTEM AREA). ARE YOU SURE? 1.YES 2.NO
Completion Press [CUSTOM SETTINGS] key.
SIMULATION 62-10 JOB COMPLETE DATA CLEAR. (WITH JOB LOG DATA) OK. (or NG)
62-11 Purpose Function (Purpose) Section Item Data clear Used to delete document filing data. (The management area (standard folder, user folder) is cleared.) (Only in the model with a disk installed) MFP controller (HDD) Clear
Operation/Procedure
Completion Press [CUSTOM SETTINGS] key.
1) Select YES/NO of deleting the document filing data. 1 2 YES NO Execution Cancel
2) Press [START] key. During formatting, "EXECUTING" is displayed. When formatting is completed normally, "OK" is displayed. If not, "NG" is displayed. NOTE: When executed, this function internally executes the same function as SIM66-10;deleting reservation data, bulletin board data, and confidential data.
SIMULATION 62-11 DOCUMENT FILING DATA CLEAR. ARE YOU SURE? 1. YES 2. NO
62-10 Data clear Used to delete a job complete list (also to delete job log data) (Only in the model with a disk installed) Section MFP controller (HDD) Item Clear Operation/Procedure 1) Select YES/NO of deleting the job complete list. 1 2 YES NO Execution Cancel Purpose Function (Purpose)
2) Press [START] key. During formatting, "EXECUTING" is displayed. When formatting is completed normally, "OK" is displayed. If not, "NG" is displayed. NOTE: When executed, this function also deletes the complete queues of E-MAIL, FAX and IFAX, reservation data associated with the image send function, bulletin board data, and confidential data.
SIMULATION 62-11 DOCUMENT FILING DATA CLEAR. EXECUTING.
Completion
63
63-1 Purpose Function (Purpose) Section Item CCD data Values Description ODD GAIN Od pixel gain adjustment value EVEN GAIN Even pixel gain adjustment value MAX All pixel MAX MIN All pixel MIN AVE All pixel average OFFSET All offset CIS data : Only when DSPF installed Values Description GAIN Gain adjustment value MAX Pixel MAX MIN Pixel MIN AVE Pixel average OFFSET Black offset DEV Standard deviation
SIMULATION 63-1 SHADING DATA DISPLAY. (CCD) ODD GAIN: 128 EVEN GAIN: 128 OFFSET: 126 MIN.: 128 AVE.: 128 (CIS) GAIN: 128 MIN.: 128
SIMULATION 63-2 SHADING EXECUTION. SELECT1-2, AND PRESS START. 1. OC SHADING 2. DSPF SHADING
Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the result of shading correction. (The shading correction data are displayed.) Optical (Image scanning) Operation
Operation/Procedure
Completion
63-7 Purpose Function (Purpose) Section Item Adjustment Used to adjust the white plate scan start position for shading. (Document table mode) Laser (Exposure) Operation
Operation/Procedure 1) Enter 1 with 10-key. 2) Press [START] key. 3) Enter the adjustment value with 10-key. 4) Press [START] key.
MAX.: 128
When a shading error occurs, this adjustment value is changed. 1 CCD Item CCD scan Set range 1 - 16 Default 6
63-2 Purpose Function (Purpose) Section Item Adjustment Used to execute shading. Optical (Image scanning) Operation
1
Press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
Operation/Procedure 1) Enter the number corresponding to the shading mode to be executed. 1 2 OC SHADING DSPF SHADING OC analog level correction and shading correction (Document table mode) DSPF analog level correction and shading correction
SIMULATION 63-7 SHADING POSITION ADJUSTMENT. INPUT VALUE 1-16, AND PRESS START. 1. CCD
2) Press [START] key. During execution, "EXECUTING" is displayed. When execution is completed normally, "COMPLETED" is displayed.
manuals4you.com
64
64-1 Purpose Function (Purpose) Operation test/Check Used to check the operation of the printer section (self-print operation), (The print pattern, the paper feed mode, the print mode, the print quantity, and the density can be optionally set.) Operation
(Table 1)
0 TRAY SELECT 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT PRINT START Paper feed tray 1: Tray 1 2: Tray 2 3: Tray 3 4: Tray 4 5: Manual feed Print execution (Printing of the set data is executed.) PRINT PATTERN Print pattern (Note 1) DENSITY Graphic density (Valid only when No. 79, 80 or 84 is selected.) MULTI Print quantity MODE Print mode 1. Standard 1. STANDARD 2. Smoothing ON 2. SMOOTHING 3. TONER SAVE 3. Smoothing ON 3. Toner save ON 4. HALF TONE 5. SMOOTHING + TONER 4. Half tone ON SAVE 5. Smoothing + toner save 6. SMOOTHING + HALF TONE 6. Smoothing + half tone 7. TONER SAVE + HALF 7. Toner save + half tone 8. Smoothing + toner save + TONE 8. SMOOTHING + TONER half tone SAVE + HALF TONE LEVEL (Parameter of print image process) DUPLEX Duplex 1. NO 0: NO (Simplex) 2. YES 1: YES (Duplex)
1 2 3 4 5
Item
Operation/Procedure (Various print patterns output) (Table 1) 1) Select PRINT PATTERN with 10-key. 2) Enter the number corresponding to the print pattern to be printed with 10-key. 3) Press [START] key. 4) Select PRINT START with 10-key. 5) Press [START] key. (Print condition setting in this simulation) To select paper (paper feed tray), perform the following procedures. 1) Select TRAY SELECT with 10-key. 2) Press [START] key. 3) Enter the number corresponding to the paper feed tray of the target paper with 10-key. 4) Press [START] key. (The paper feed tray is selected.) To adjust the print density, perform the following procedures. 1) Select DENSITY with 10-key. 2) Enter the adjustment value with 10-key. 3) Press [START] key. To set the print quantity, perform the following procedures. 1) Select MULTI with 10-key. 2) Enter the print quantity with 10-key. 3) Press [START] key. To set the print quality mode, perform the following procedures. 1) Select MODE with 10-key. 2) Enter the number corresponding to the print quality mode with 10-key. 3) Press [START] key. To set the print level, perform the following procedures. 1) Select LEVEL with 10-key. 2) Enter the adjustment value with 10-key. 3) Press [START] key. NOTE: In some print patterns, changing the level may not change the picture quality. To set duplex/simplex print, perform the following procedures. 1) Select DUPLEX with 10-key. 2) Enter the number corresponding to the operation mode with 10-key. 3) Press [START] key.
6 7
(Note 1) Print pattern No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Engine Controller Pattern pattern For off-center adjustment Main scanning direction 1 by 5 Main scanning direction 1mmpitch Main scanning direction 3 by 3 Sub scanning direction 1 by 1 Sub scanning direction 1 by 5 Sub scanning direction 2 by 4 Sub scanning direction 3 by 3 Right oblique 1 by 2 Right oblique 1 by 5 Right oblique 2 by 4 Right oblique 3 by 3 Left oblique 1 by 2 Left oblique 1 by 5 Left oblique 2 by 4 Left oblique 3 by 3 Dot 1 by 1 Dot 3 by 3 Dot Solid black Main scanning direction 1 by 1 Main scanning direction 5 by 1 Main scanning direction 4 by 2 Main scanning direction 3 by 3 Sub scanning direction 1 by 1 Sub scanning direction 5 by 1 Sub scanning direction 4 by 2 Sub scanning direction 3 by 3 Right oblique 2 by 1 Right oblique 5 by 1 Right oblique 4 by 2 Right oblique 3 by 3 Left oblique 2 by 1 Left oblique 5 by 1 Left oblique 4 by 2 Left oblique 3 by 3 Note
No 37 38 39 40 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 98
Engine Controller Pattern pattern Dot 1 by 1 Dot 3 by 3 Dot Solid white All surface 1 by 1 (Vertical) All surface 1 by 1 (Horizontal) All surface 1 by 2 (Vertical) All surface 1 by 2 (Horizontal) All surface 1 by 3 (Vertical) All surface 1 by 3 (Horizontal) All surface 1 by 4 (Vertical) All surface 1 by 4 (Horizontal) All surface 1 by 5 (Vertical) All surface 1 by 5 (Horizontal) All surface 2 by 2 (Vertical) All surface 2 by 2 (Horizontal) All surface 2 by 3 (Vertical) All surface 2 by 3 (Horizontal) All background Special pattern For every other 1 block width 128 pixels/ 32 gradations For every other 1 block width 128 pixels/ 16 gradations For every other 1 block width 128 pixels/ 8 gradations 1-dot pattern Print adjustment pattern with scale (Vertical) Grid pattern Slant line 45 degrees Slant line 26.6 degrees Slant line 63.4 degrees ID/BG pattern Dot pattern 12.5% Dot pattern 28% Dot pattern 50% All surface effort diffusion background All surface dither process background For every other 1 block width 128 pixels/ 32 gradations For every other 1 block width 128 pixels/ 16 gradations For every other 1 block width 128 pixels/ 8 gradations Memory check pattern Cleaning check pattern Offset check pattern Text pattern A Text pattern B Text pattern C Toner quantity measuring chart Radiation chart Data printing
Note
SIMULATION 64-1 SELF PRINT MODE. SELECT 0. TRAY SELECT :1 1. 2. PRINT PATTERN:87 3. 4. MULTI : 1 5. 6. LEVEL : 1 7.
(2)
SIMULATION 64-1 SELF PRINT MODE. INPUT VALUE, AND PRESS START. (PRINT PATTERN) INPUT 1-98.
71
(3)
SIMULATION 64-1 SELF PRINT MODE. INPUT VALUE, AND PRESS START. (DENSITY) 1-255
100
(4)
SIMULATION 64-1 SELF PRINT MODE. INPUT VALUE, AND PRESS START. (MULTI COUNT) 1-999
(5)
SIMULATION 64-1 SELF PRINT MODE. SELECT (MODE) 1.STANDARD 2.SMOOTHING 5.SMOOTHING+ TONER SAVE 7.TONER SAVE+ HALF TONE 8.SMOOTHING+ TONER SAVE+
1-8, AND PRESS START. 3.TONER SAVE 4.HALF TONE 6.SMOOTHING+ HALF TONE HALF TONE
(6)
SIMULATION 64-1 SELF PRINT MODE. INPUT VALUE, AND PRESS START. (LEVEL) 1-5
(0)
SIMULATION 64-1 SELF PRINT MODE. SELECT 1-5, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
(7)
SIMULATION 64-1 SELF PRINT MODE. SELECT 1-2, AND PRESS START. (DUPLEX) 1.NO 2.YES SIMULATION 64-1 SELFT PRINT MODE.. EXECUTING 0. TRAY SELECT :1 2. PRINT PATTERN:87 3. DENSITY 4. MULTI : 1 5. MODE 6. LEVEL : 1 7. DUPLEX
:1 :1 :1
: Error diffusion process Note*: Since the "DENSITY" of an actual copy or printer output differs, they differ from the output of self print.
manuals4you.com
65
65-1 Purpose Function (Purpose) Section Item Adjustment Used to adjust the touch panel (LCD display section) detection position. Operation (Display/Operation key)
2) Enter the number corresponding to the bit to be changed with 10-key. (Example) When the bit of 5 is to be changed, enter 5. The set value of 1/0 is alternatively changed every time when the target key is pressed. 3) After completion of setting of all the bits, press [START] key.
SIMULATION 66-1 FAX SOFT SW. SETTING. SELECT 2-120, AND PRESS START.
Operation/Procedure Touch the four cross marks (+) sequentially. The coordinates of pressed positions are set. When the coordinates setting is completed normally, the display turns gray. When all the four points are set, the display returns to the normal state.
SIMULATION 65-1
Press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
SIMULATION 66-1 FAX SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS START. 1 2 3 4 5 6 7 8 SOFT SW-2:
66-2 65-2 Purpose Function (Purpose) Section Item Adjustment/Setup/Operation data output/Check (Display/Print) Used to check the result of the touch panel (LCD display) detection position adjustment. (The coordinates are displayed.) Operation (Display/Operation key) Purpose Function (Purpose) Section Item Data clear Used to clear the FAX soft switch function data and to set to the default. (Excluding the adjustment values.) (Only when FAX is installed) FAX Data
Operation/Procedure 1) Set the destination code with 10-key. Japan U.S.A. Australia U.K. France Germany Sweden Newzealand China Singapore TW Other1 Other2 Ohter3 00000000 10110101 00001001 10110100 00111101 00000100 10100101 01111110 00100110 10011100 11111110 11111101 11111100 11111011 Finland Norway Denmark Netherlands Italy Switzerland Austria Indonesia Thailand Malaysia India Philippines Hongkong 00111100 10000010 00110001 01111011 01011001 10100110 00001010 01010100 10101001 01101100 01010011 10001001 01010000
Operation/Procedure When the touch panel is touched, the X and Y coordinate values of the touched point and the coordinate values of the specified point are displayed. The coordinate values set with SIM 65-1 are used as the reference.
SIMULATION 65-2
100 100 200 300 400 40 500 600
140
600 200
180
66
66-1 Purpose Function (Purpose) Setting Used to change and check the FAX soft switch functions. (Used to change and check the functions provided for the FAX soft switches.) (Only when FAX is installed) FAX
2) Press [START] key. 3) The confirmation menu of YES/NO of clear is displayed. Select one. 1 2 YES NO FAX soft SW is cleared. Not cleared.
4) Press [START] key. The soft switch (except for the adjustment values) is cleared according to the destination selected in procedure 1). NOTE: When the FAX BOX is not installed, initialization including the adjustment value is performed. (The adjustment value is stored in the FAX BOX.)
Section Item
Operation/Procedure Setting of soft switches other than SW1 can be changed and checked. 1) Enter the soft switch number to be checked or changed with 10-key. The current set state is displayed. AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 73
SIMULATION 66-2 FAX SOFT SW. CLEAR(WITHOUT ADJUSTMENT VALUE). INPUT COUNTRY CODE, AND PRESS START.
1 2 3 4 5 6 7 8
SIMULATION 66-3 FAX PWB MEMORY CHECK INPUT 1-13, AND PRESS START. 1. All Memory Device Check (once) 2. MFP SRAM(once) 3. MFP SRAM(repeat) 4. MFP FLASH+ OP.FLASH(once) 5. MFP FLASH+ OP.FLASH(repeat) 6. MODEM EEPROM(once) 7. MODEM EEPROM(repeat) 8. MODEM SRAM(G/A)(once) 9. MODEM SRAM(G/A)(repeat) 10. MODEM SDRAM1(once) 11. MODEM SDRAM1(repeat) 12. MODEM SDRAM2(once) 13. MODEM SDRAM2(repeat)
SIMULATION 66-2 FAX SOFT SW. CLEAR. ARE YOU SURE? JAPAN 1:YES 2:NO
66-3 Purpose Function (Purpose) Operation test/Check Used to check the operation of the FAX PWB memory (read/write). (This adjustment is required when the PWB is replaced with a new one.) (Only when FAX is installed) FAX Data
SIMULATION 66-3 FAX PWB MEMORY CHECK MFP SRAM: CHECKING MFP FLASH: NO CHECK MFP OP.FLASH: NO CHECK MODEM EEPROM: NG:A0010000 MODEM SRAM(G/A):NO CHECK MODEM SDRAM1: NG A11 MODEM SDRAM2: OK
When "repeat" is selected and [CUSTOM SETTINGS] key is pressed.
Section Item
When Check is "once," the display stops at the result display. When [CUSTOM SETTINGS] key is pressed, the display returns to the initial display. 66-4 Purpose Function (Purpose) Operation test/Check Used to check the output operation of data signals in each data output mode of FAX. (Used to check the operation of MODEM. ) Send level: Max. (Only when FAX is installed) FAX Operation
Operation/Procedure 1) Enter the number corresponding to the memory to be checked with 10-key. 2) Press [START] key. In the case of All, all memories are checked only once. Check connection wire list NO CHECK CHECKING OK NG Not checked yet. Checking Check complete OK Check complete NG
Section Item
Operation/Procedure 1) Enter the number corresponding to the output mode with 10key. 2) Press [START] key. The output is delivered at the max. send level. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 NOSIGNAL 33.6 V34 31.2 V34 28.8 V34 26.4 V34 24.0 V34 21.6 V34 19.2 V34 16.8 V34 14.4 V34 12.0 V34 9.6 V34 7.2 V34 4.8 V34 2.4 V34 14.4 V33 No signal 26.4 V34 31.2 V34 28.8 V34 26.4 V34 24.0 V34 21.6 V34 19.2 V34 16.8 V34 14.4 V34 12.0 V34 9.6 V34 7.2 V34 4.8 V34 2.4 V34 14.4 V33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 12.0 V33 14.4 V17 12.0 V17 9.6 V17 7.2 V17 9.6 V29 7.2 V29 4.8 V27t 2.4 V27t 0.3 FLG CED 2100 CNG 1100 0.3 V21 ANSam RINGER No RBT 12.0 V33 14.4 V17 12.0 V17 9.6 V17 7.2 V17 9.6 V29 7.2 V29 4.8 V27t 2.4 V27t 0.3 FLG CED 2100 CNG 1100 0.3 V21 ANSam RINGER No RBT
The error address or the data line is displayed individually. Target memory of check MFP SRAM MFP FLASH MFP OP.FLASH MODEM EEPROM MODEM SRAM (G/A) MODEM SDRAM1 MODEM SDRAM2 SRAM FLASH ROM
When "repeat" is selected, the operation is repeated until the result is "NG" or [CUSTOMSETTING" is pressed.
When [CUSTOM SETTINGS] key is pressed during execution, execution is stopped. When a number is entered and [START] key is pressed during execution, the kind of signal can be changed.
manuals4you.com
SIMULATION 66-4 SIGNAL OUTPUT CHECK.(LEVEL MAX) START. 1.NOSIGNAL 2.26.4 V34 9.16.8 V34 13.7.2 V34 17.12.0 V33 21.7.2 V17 25.2.4 V27t 29.0.3 V21 2.33.6 V34 6.24.0 V34 10.14.4 V34 14.4.8 V34 18.14.4 V17 22.9.6 V29 26.0.3 FLG 30.ANSam
SELECT 1-32, AND PRESS 4.28.8 V34 8.19.2 V34 12.9.6 V34 16.14.4 V33 20.9.6 V17 24.4.8 V27t 28.CNG 1100 32.No RBT
3.31.2 V34 7.21.6 V34 11.12.0 V34 15.2.4 V34 19.12.0 V17 23.7.2 V29 27.CED 2100 31.RINGER
SELECT 1-32, AND PRESS 4.28.8 V34 8.19.2 V34 12.9.6 V34 16.14.4 V33 20.9.6 V17 24.4.8 V27t 28.CNG 1100 32.No RBT
1.NOSIGNAL 2.26.4 V34 9.16.8 V34 13.7.2 V34 17.12.0 V33 21.7.2 V17 25.2.4 V27t 29.0.3 V21
2.33.6 V34 6.24.0 V34 10.14.4 V34 14.4.8 V34 18.14.4 V17 22.9.6 V29 26.0.3 FLG 30.ANSam
3.31.2 V34 7.21.6 V34 11.12.0 V34 15.2.4 V34 19.12.0 V17 23.7.2 V29 27.CED 2100 31.RINGER
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
NOSIGNAL 33.6 V34 31.2 V34 28.8 V34 26.4 V34 24.0 V34 21.6 V34 19.2 V34 16.8 V34 14.4 V34 12.0 V34 9.6 V34 7.2 V34 4.8 V34 2.4 V34 14.4 V33
No signal 26.4 V34 31.2 V34 28.8 V34 26.4 V34 24.0 V34 21.6 V34 19.2 V34 16.8 V34 14.4 V34 12.0 V34 9.6 V34 7.2 V34 4.8 V34 2.4 V34 14.4 V33
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
12.0 V33 14.4 V17 12.0 V17 9.6 V17 7.2 V17 9.6 V29 7.2 V29 4.8 V27t 2.4 V27t 0.3 FLG CED 2100 CNG 1100 0.3 V21 ANSam RINGER No RBT
12.0 V33 14.4 V17 12.0 V17 9.6 V17 7.2 V17 9.6 V29 7.2 V29 4.8 V27t 2.4 V27t 0.3 FLG CED 2100 CNG 1100 0.3 V21 ANSam RINGER No RBT
When [CUSTOM SETTINGS] key is pressed during execution, execution is stopped. When a number is entered and [START] key is pressed during execution, the kind of signal can be changed.
SIMULATION 66-5 SIGNAL OUTPUT CHECK.(SOFT SW.) START. 1.NOSIGNAL 2.26.4 V34 9.16.8 V34 13.7.2 V34 17.12.0 V33 21.7.2 V17 25.2.4 V27t 29.0.3 V21 2.33.6 V34 6.24.0 V34 10.14.4 V34 14.4.8 V34 18.14.4 V17 22.9.6 V29 26.0.3 FLG 30.ANSam SELECT 1-32, AND PRESS 4.28.8 V34 8.19.2 V34 12.9.6 V34 16.14.4 V33 20.9.6 V17 24.4.8 V27t 28.CNG 1100 32.No RBT
SIMULATION 66-4 SIGNAL OUTPUT CHECK.(LEVEL MAX) START. EXECUTING. 1.NOSIGNAL 2.26.4 V34 9.16.8 V34 13.7.2 V34 17.12.0 V33 21.7.2 V17 25.2.4 V27t 29.0.3 V21 2.33.6 V34 6.24.0 V34 10.14.4 V34 14.4.8 V34 18.14.4 V17 22.9.6 V29 26.0.3 FLG 30.ANSam
SELECT 1-32, AND PRESS 4.28.8 V34 8.19.2 V34 12.9.6 V34 16.14.4 V33 20.9.6 V17 24.4.8 V27t 28.CNG 1100 32.No RBT
3.31.2 V34 7.21.6 V34 11.12.0 V34 15.2.4 V34 19.12.0 V17 23.7.2 V29 27.CED 2100 31.RINGER
3.31.2 V34 7.21.6 V34 11.12.0 V34 15.2.4 V34 19.12.0 V17 23.7.2 V29 27.CED 2100 31.RINGER
SELECT 1-32, AND PRESS 4.28.8 V34 8.19.2 V34 12.9.6 V34 16.14.4 V33 20.9.6 V17 24.4.8 V27t 28.CNG 1100 32.No RBT
SIMULATION 66-4 SIGNAL OUTPUT CHECK.(LEVEL MAX) START. 1.NOSIGNAL 2.26.4 V34 9.16.8 V34 13.7.2 V34 17.12.0 V33 21.7.2 V17 25.2.4 V27t 29.0.3 V21 2.33.6 V34 6.24.0 V34 10.14.4 V34 14.4.8 V34 18.14.4 V17 22.9.6 V29 26.0.3 FLG 30.ANSam
SELECT 1-32, AND PRESS 4.28.8 V34 8.19.2 V34 12.9.6 V34 16.14.4 V33 20.9.6 V17 24.4.8 V27t 28.CNG 1100 32.No RBT
3.31.2 V34 7.21.6 V34 11.12.0 V34 15.2.4 V34 19.12.0 V17 23.7.2 V29 27.CED 2100 31.RINGER
1.NOSIGNAL 2.26.4 V34 9.16.8 V34 13.7.2 V34 17.12.0 V33 21.7.2 V17 25.2.4 V27t 29.0.3 V21
2.33.6 V34 6.24.0 V34 10.14.4 V34 14.4.8 V34 18.14.4 V17 22.9.6 V29 26.0.3 FLG 30.ANSam
3.31.2 V34 7.21.6 V34 11.12.0 V34 15.2.4 V34 19.12.0 V17 23.7.2 V29 27.CED 2100 31.RINGER
66-5 Purpose Function (Purpose) Operation test/Check Used to check the output operation of data signals in each data output mode of FAX. (Used to check the operation of MODEM.) An output is sent at the send level set by the soft switch. (Only when FAX is installed) FAX Operation
SIMULATION 66-5 SIGNAL OUTPUT CHECK.(SOFT SW.) START. EXECUTING. 1.NOSIGNAL 2.26.4 V34 9.16.8 V34 13.7.2 V34 17.12.0 V33 21.7.2 V17 25.2.4 V27t 29.0.3 V21 2.33.6 V34 6.24.0 V34 10.14.4 V34 14.4.8 V34 18.14.4 V17 22.9.6 V29 26.0.3 FLG 30.ANSam
SELECT 1-32, AND PRESS 4.28.8 V34 8.19.2 V34 12.9.6 V34 16.14.4 V33 20.9.6 V17 24.4.8 V27t 28.CNG 1100 32.No RBT
3.31.2 V34 7.21.6 V34 11.12.0 V34 15.2.4 V34 19.12.0 V17 23.7.2 V29 27.CED 2100 31.RINGER
Section Item
Operation/Procedure 1) Enter the number corresponding to the output mode with 10key. 2) Press [START] key. The output is delivered at the send level set with the soft switch.
SIMULATION 66-5 SIGNAL OUTPUT CHECK.(SOFT SW.) START. 1.NOSIGNAL 2.26.4 V34 9.16.8 V34 13.7.2 V34 17.12.0 V33 21.7.2 V17 25.2.4 V27t 29.0.3 V21 2.33.6 V34 6.24.0 V34 10.14.4 V34 14.4.8 V34 18.14.4 V17 22.9.6 V29 26.0.3 FLG 30.ANSam SELECT 1-32, AND PRESS 4.28.8 V34 8.19.2 V34 12.9.6 V34 16.14.4 V33 20.9.6 V17 24.4.8 V27t 28.CNG 1100 32.No RBT
3.31.2 V34 7.21.6 V34 11.12.0 V34 15.2.4 V34 19.12.0 V17 23.7.2 V29 27.CED 2100 31.RINGER
66-6 Purpose Function (Purpose) Section Item 1 User data output/Check (Display/Print) Used to print the confidential pass code. (Used when the confidential pass code is forgotten.) (Only when FAX is installed) FAX Data Print start
66-8 Purpose Function (Purpose) Operation test/Check Used to check the output operation of various sound signals of FAX. (Used to check the operation of the sound output IC.) Send level: Max. (Only when FAX is installed) FAX Operation
Section Item
Operation/Procedure 1) Enter the number corresponding to the output mode with 10key. 2) Press [START] key. The output is delivered at the max. level.
1 2 3 4 5 6 7 8 9 10 NONE PAUSE MESSAGE1 MESSAGE2 MESSAGE3 MESSAGE4 MESSAGE5 MESSAGE6 MESSAGE7 MESSAGE8 Mute Pause sound Message 1 Message 2 Message 3 Message 4 Message 5 Message 6 Message 7 Message 8 11 12 13 14 15 16 17 18 19 20 MESSAGE 9 MESSAGE 10 MESSAGE 11 MESSAGE 12 MESSAGE 13 MESSAGE 14 MESSAGE 15 ALARM RINGER EXT.TEL.RINGER Message 9 Message 10 Message 11 Message 12 Message 13 Message 14 Message 15 Alarm Call ring External TEL ring
The paper is automatically selected with the size saved in the image memory.
SIMULATION 66-6 PASS CODE PRINT OUT. 1.PRINT START
PRESS START.
Press [START] key. When there is no print data, the display returns to the original state without printing. (When 1)
When the number is entered during execution, the kind of signal can be changed. When [START] key is pressed, the voice message is sent. When [CUSTOM SETTINGS] key is pressed, it is stopped.
SIMULATION 66-8 MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS START. 1.NONE 2.PAUSE 3.MESSAGE1 4.MESSAGE2 5.MESSAGE3 6.MESSAGE4 7.MESSAGE5 8.MESSAGE6 9.MESSAGE7 10.MESSAGE8 11.MESSAGE9 12.MESSAGE10 13.MESSAGE11 14.MESSAGE12 15.MESSAGE13 16.MESSAGE14 17.MESSAGE15 18.ALARM 19.RINGER 20.EXT.TEL.RINGER
66-7 Purpose Function (Purpose) Section Item User data output/Check (Display/Print) Used to print the image memory data (memory send/receive). (Only when FAX is installed) FAX Data
Operation/Procedure All image data stored in the image memory are printed. The confidential receive data are also printed. 1 PRINT START Print start
Select other 1, and press [START] key. Press [CUSTOM SETTINGS] key.
The paper is automatically selected with the size saved in the image memory.
SIMULATION 66-7 IMAGE MEMORY PRINT OUT. PRESS START. 1.PRINT START
Same display
SIMULATION 66-8 MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS START. EXECUTING. 1.NONE 2.PAUSE 3.MESSAGE1 4.MESSAGE2 5.MESSAGE3 6.MESSAGE4 7.MESSAGE5 8.MESSAGE6 9.MESSAGE7 10.MESSAGE8 11.MESSAGE9 12.MESSAGE10 13.MESSAGE11 14.MESSAGE12 15.MESSAGE13 16.MESSAGE14 17.MESSAGE15 18.ALARM 19.RINGER 20.EXT.TEL.RINGER
SIMULATION 66-8 MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS START. EXECUTING. 1.NONE 2.PAUSE 3.MESSAGE1 4.MESSAGE2 5.MESSAGE3 6.MESSAGE4 7.MESSAGE5 8.MESSAGE6 9.MESSAGE7 10.MESSAGE8 11.MESSAGE9 12.MESSAGE10 13.MESSAGE11 14.MESSAGE12 15.MESSAGE13 16.MESSAGE14 17.MESSAGE15 18.ALARM 19.RINGER 20.EXT.TEL.RINGER
SIMULATION 66-8 MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS START. 1.NONE 2.PAUSE 3.MESSAGE1 4.MESSAGE2 5.MESSAGE3 6.MESSAGE4 7.MESSAGE5 8.MESSAGE6 9.MESSAGE7 10.MESSAGE8 11.MESSAGE9 12.MESSAGE10 13.MESSAGE11 14.MESSAGE12 15.MESSAGE13 16.MESSAGE14 17.MESSAGE15 18.ALARM 19.RINGER 20.EXT.TEL.RINGER
manuals4you.com
66-9 Purpose Function (Purpose) Operation test/Check Used to check the output operation of various sound signals of FAX. (Used to check the operation of the sound output IC.) An output is sent at the send level set by the soft switch. (Only when FAX is installed) FAX Operation
66-10 Purpose Function (Purpose) User data output/Check (Display/Print) Used to clear all data of the image memory (memory send/receive). The confidential data are also cleared at the same time. (Only when FAX is installed) FAX Data
Section Item
Section Item
Operation/Procedure 1) Select YES/NO of image memory clear with 10-key. 1 2 YES NO Image memory clear is executed. Clear is not executed.
Operation/Procedure 1) Enter the number corresponding to the output mode with 10key. 2) Press [START] key. The output is delivered at the send level set with the soft SW.
1 2 3 4 5 6 7 8 9 10 NONE PAUSE MESSAGE1 MESSAGE2 MESSAGE3 MESSAGE4 MESSAGE5 MESSAGE6 MESSAGE7 MESSAGE8 Mute Pause sound MESSAGE 1 MESSAGE 2 MESSAGE 3 MESSAGE 4 MESSAGE 5 MESSAGE 6 MESSAGE 7 MESSAGE 8 11 12 13 14 15 16 17 18 19 20 MESSAGE 9 MESSAGE10 MESSAGE11 MESSAGE12 MESSAGE13 MESSAGE14 MESSAGE15 ALARM RINGER EXT.TEL.RINGER MESSAGE 9 MESSAGE 10 MESSAGE 11 MESSAGE 12 MESSAGE 13 MESSAGE 14 MESSAGE 15 Alarm Call ring External TEL ring
2) Press [START] key. The SRAM image data management table and image data in the Flash ROM area and HD (except for filing images) are cleared.
SIMULATION 66-10 IMAGE MEMORY CLEAR ARE YOU SURE? 1. YES 2. NO
Press [START] key to clear.
When the number is entered during execution, the kind of signal can be changed. When [START] key is pressed, the voice message is sent. When [CUSTOM SETTINGS] key is pressed, it is stopped.
SIMULATION 66-9 MESSAGE OUTPUT CHECK.(SOFT SW.) SELECT 1-20, AND PRESS START. 1.NONE 2.PAUSE 3.MESSAGE1 4.MESSAGE2 5.MESSAGE3 6.MESSAGE4 7.MESSAGE5 8.MESSAGE6 9.MESSAGE7 10.MESSAGE8 11.MESSAGE9 12.MESSAGE10 13.MESSAGE11 14.MESSAGE12 15.MESSAGE13 16.MESSAGE14 17.MESSAGE15 18.ALARM 19.RINGER 20.EXT.TEL.RINGER
The processing status of image memory clear is displayed with "+." 66-11 Purpose Function (Purpose) Operation test/Check Used to check the output operation of FAX G3 mode 300bps. (Used to check the operation of MODEM.) Send level: Max. (Only when FAX is installed) FAX Operation
Select other 1, and press [START] key. Press [CUSTOM SETTINGS] key.
Section Item
Same display
SIMULATION 66-9 MESSAGE OUTPUT CHECK.(SOFT SW.) SELECT 1-20, AND PRESS START. EXECUTING. 1.NONE 2.PAUSE 3.MESSAGE1 4.MESSAGE2 5.MESSAGE3 6.MESSAGE4 7.MESSAGE5 8.MESSAGE6 9.MESSAGE7 10.MESSAGE8 11.MESSAGE9 12.MESSAGE10 13.MESSAGE11 14.MESSAGE12 15.MESSAGE13 16.MESSAGE14 17.MESSAGE15 18.ALARM 19.RINGER 20.EXT.TEL.RINGER
Operation/Procedure 1) Select the number corresponding to the output mode with 10key. 2) Press [START] key. The signal is sent in the max. send level. 1 2 3 NO SIGNAL 11111 11110 No signal 11111 11110 4 5 6 00000 010101 00001 00000 010101 00001
SIMULATION 66-9 MESSAGE OUTPUT CHECK.(SOFT SW.) SELECT 1-20, AND PRESS START. EXECUTING. 1.NONE 2.PAUSE 3.MESSAGE1 4.MESSAGE2 5.MESSAGE3 6.MESSAGE4 7.MESSAGE5 8.MESSAGE6 9.MESSAGE7 10.MESSAGE8 11.MESSAGE9 12.MESSAGE10 13.MESSAGE11 14.MESSAGE12 15.MESSAGE13 16.MESSAGE14 17.MESSAGE15 18.ALARM 19.RINGER 20.EXT.TEL.RINGER
When the number is entered during execution, the kind of signal can be changed. When [CUSTOM SETTINGS] key is pressed during execution, the operation is stopped.
SIMULATION 66-11 300bps SIGNAL OUTPUT.(LEVEL MAX) START. 1. NO SIGNAL 2. 11111 3. 11110 5. 010101 6. 00001
SIMULATION 66-12 300bps SIGNAL OUTPUT.(SOFT SW.) START. 1. NO SIGNAL 5. 010101 2. 11111 6. 00001 3. 11110
4. 00000
Press [CUSTOM SETTINGS] key Press [START] key. Press [CUSTOM SETTING] key.
SIMULATION 66-11 300bps SIGNAL OUTPUT.(LEVEL MAX) START. EXECUTING. 1. NO SIGNAL 2. 11111 3. 11110 5. 010101 6. 00001
Same display Select 3 and press [START] key.
4. 00000
SIMULATION 66-12 300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS START. EXECUTING. 1. NO SIGNAL 2. 11111 3. 11110 4. 00000 5. 010101 6. 00001
Same display
SIMULATION 66-11 300bps SIGNAL OUTPUT.(LEVEL MAX) START. EXECUTING. 1. NO SIGNAL 2. 11111 3. 11110 5. 010101 6. 00001
4. 00000
SIMULATION 66-12 300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS START. EXECUTING. 1. NO SIGNAL 2. 11111 3. 11110 4. 00000 5. 010101 6. 00001
66-12 Purpose Function (Purpose) Operation test/Check Used to check the output operation of FAX G3 mode 300bps. (Used to check the operation of MODEM.) An output is send at the send level set by the soft switch. (Only when FAX is installed) FAX Operation 66-13 Purpose Function (Purpose) Setting Used to enter (set) the number of FAX dial signal output test. (The dial number set by this simulation is outputted when the dial signal output test is made by SIM 66-14 - 16. ) (Only when FAX is installed) FAX Data
Section Item
Operation/Procedure 1) Select the number corresponding to the output mode with 10key. 2) Press [START] key. The signal is sent in the send level set with the soft switch. 1 2 3 NO SIGNAL 11111 11110 No signal 11111 11110 4 5 6 00000 010101 00001 00000 010101 00001
Section Item
Operation/Procedure 1) Enter the dial number with 10-key. Use 10-key, [*] key, and [#] key to enter the number. The upper limit is 20 digits. When [CLEAR] key is pressed, the mode returns to the initial state. 2) Press [START] key.
SIMULATION 66-13 DIAL TEST NUMBER SETTING. INPUT NUMBER AND PRESS START. 0123456789*#01234567
When the number is entered during execution, the kind of signal can be changed. When [CUSTOM SETTINGS] key is pressed during execution, the operation is stopped.
66-14 Purpose Function (Purpose) Setting/Operation test/Check Used to set the make time in the FAX pulse dial mode (10pps) and to test the dial signal output. (The dial number signal set by SIM 66-13 is outputted.) Used to check troubles in dialing and to check the operation. (Only when FAX is installed) FAX Operation
Section Item
Operation/Procedure 1) Enter 0 with 10-key. 2) Press [START] key. The dial signal is outputted.
manuals4you.com
(Dial pulse make time setting) 1) Enter 1 with 10-key. 2) Press [START] key. 3) Enter the set value with 10-key. 4) Press [START] key. 0 1 EXECUTE MAKE TIME Execute Dial pulse make time setting (0 - 15)
Select 0 and press [START] key. Select 1 and press [START] key. Press [CUSTOM SETTINGS] key or press [START] key.
SIMULATION 66-15 DIAL TEST(20PPS). SELECT 0-1, AND PRESS START. 0. EXECUTE 1. MAKE TIME 7 ; [+9 ms]
The dial signal is sent with the set value + 29ms. When [CUSTOM SETTINGS] key is pressed during execution, the operation is stopped.
SIMULATION 66-14 DIAL TEST(10PPS). SELECT 0-1, AND PRESS START. 0. EXECUTE 1. MAKE TIME 7 ; [+29 ms]
7
Press [CUSTOM SETTINGS] key.
Select 1 and Press [CUSTOM SETTINGS] key press [START] key. or press [START] key.
66-16
7
Press [CUSTOM SETTINGS] key.
Section Item
Setting/Operation test/Check Used to check the dial signal (DTMF) output in the FAX tone dial mode. (The dial number signal set by SIM 66-13 is outputted.) The send level can be set to an optional level. Used to check troubles in dialing and to check the operation. (Only when FAX is installed) FAX Operation
Operation/Procedure 66-15 Purpose Function (Purpose) Setting/Operation test/Check Used to set the make time in the FAX pulse dial mode (20pps) and to test the dial signal output. (The dial number signal set by SIM 66-13 is outputted.) Used to check troubles in dialing and to check the operation. (Only when FAX is installed) FAX Operation 1) Enter 0 with 10-key. 2) Press [START] key. The dial signal is outputted. (Dial pulse make time setting) 1) Enter 1 or 2 with 10-key. 2) Press [START] key. 3) Enter the set value with 10-key. 4) Press [START] key. 0 1 2 EXECUTE HIGH HIGH LOW Item Execution High group level High group - Low group Set range 0 - 15dB 0 - 15
Section Item
Operation/Procedure 1) Enter 0 with 10-key. 2) Press [START] key. The dial signal is outputted. (Dial pulse make time setting) 1) Enter 1 with 10-key. 2) Press [START] key. 3) Enter the set value with 10-key. 4) Press [START] key. 0 1 EXECUTE MAKE TIME Execute Dial pulse make time setting (0 - 15)
When [CUSTOM SETTINGS] key is pressed during execution, the operation is stopped.
The dial signal is sent with the set value + 9ms. When [CUSTOM SETTINGS] key is pressed during execution, the operation is stopped.
The signal is sent in the send level set with the soft SW.
SIMULATION 66-16 DIAL TEST(DTMF). SELECT 0-2, AND PRESS START. 0. EXECUTE 1. HIGH 7 (dB) 2. HIGH-LOW 7
When [CUSTOM SETTINGS] key is pressed during execution, the operation is stopped.
1
7
Press [START] key. Press [CUSTOM SETTINGS] key.
SIMULATION 66-16 DIAL TEST(DTMF). SELECT 0-15, AND PRESS START. 1. HIGH(dB)
(When 2)
EXECUTING.
SIMULATION 66-16 DIAL TEST(DTMF). SELECT 0-15, AND PRESS START. 1. HIGH(dB)
7
66-19 Purpose Function (Purpose) Section Item
Data transfer Used to back-up the HDD data into the Flash memory (optional FAX expansion memory: ARMM9). (Only when FAX is installed) FAX Data
66-17 Purpose Function (Purpose) Section Item Setting Used to check the dial signal (DTMF) output in the FAX tone dial mode. Send level: Max. Used to check the operation. (Only when FAX is installed) FAX Operation
Operation/Procedure 1) Select YES/NO of data transfer (backup). 1 2 YES NO Backup is executed. Backup is not executed.
2) Press [START] key. This function is valid only when the AR-MM9 is installed. Backup contents Address book data (FAX, Mail, Address) One-touch dial Item name FTP expansion Fine name Group expansion FAX receive select table Program IFAX receive YES/NO Use index Polling allow number Standard sender Memory box IFAX sender registration Sender name FAX sender registration Soft SW
Operation/Procedure 1) Enter the DTMF signal (1 - 9, 0, *, #) to be sent with 10-key. 2) Press [START] key. The signal is sent in the max. send level. When [CUSTOM SETTINGS] key is pressed during execution, the operation is stopped.
SIMULATION 66-17 DTMF SIGNAL OUTPUT.(LEVEL MAX) PRESS START.
1
Press [START] key. Press [CUSTOM SETTINGS] key.
EXECUTING.
1
66-18 Purpose Function (Purpose) Setting Used to check the dial signal (DTMF) output in the FAX tone dial mode. An output is sent at the send level set by the soft switch. Used to check the operation. (Only when FAX is installed) FAX Operation
SIMULATION 66-19 ADDRESS DATA BACK UP. (WRITE TO FLASH ROM) EXECUTING...
1
After completion of backup
Section Item
Operation/Procedure 1) Enter the DTMF signal (1 - 9, 0, *, #) to be sent with 10-key. 2) Press [START] key. AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 80
manuals4you.com
66-20 Purpose Function (Purpose) Section Item Data transfer Used to read the back-up data by SIM 66-19 to the SRAM/HDD. (Only when FAX is installed) FAX Data
66-22 Purpose Function (Purpose) Section Item Setting Used to adjust the handset volume. (Only when the FAX is installed.) FAX Operation
Operation/Procedure 1) Select YES/NO of data transfer. 1 2 YES NO Backup is executed. Backup is not executed.
Operation/Procedure 1) Enter the number corresponding to the volume with 10-key. 2) Press [START] key. 1 2 3 MIN MIDDLE MAX Small Medium Large
SIMULATION 66-22 HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START. 1. MIN 2. MIDDLE 3. MAX
Press [START] key.
2
Press [CUSTOM SETTINGS] key.
SIMULATION 66-20 ADDRESS DATA BACK UP. (READ FROM FLASH ROM) EXECUTING...
1
After completion of read
SIMULATION 66-22 HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START. EXECUTING. 1. MIN 2. MIDDLE 3. MAX
66-21 Purpose Function (Purpose) Adjustment/Setup/Operation data output/Check (Display/Print) Used to print information related to FAX (various registrations, communication management, file management, system error protocol). (Only when FAX is installed) FAX Data
Same display Select 3 and press [START] key.
Section Item
SIMULATION 66-22 HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START. EXECUTING. 1. MIN 2. MIDDLE 3. MAX
Operation/Procedure 1) Enter the number corresponding to the information (item) to be printed with 10-key. 2) Press [START] key. 1 2 3 4 5 REGISTERED MANAGEMENT FILE MANAGEMENT SYSTEM ERROR PROTOCOL Various registration information Communication management information File management information System error information Protocol information
SIMULATION 66-22 HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START. 1. MIN 2. MIDDLE 3. MAX
66-23 Purpose Function (Purpose) Section Item Setting Used to download the FAX program. (Only when FAX is installed) Not used in the market. (For development) FAX
SIMULATION 66-21 FAX INFORMATION PRINT OUT. SELECT 1-5, AND PRESS START. 1. REGISTERED 2. MANAGEMENT 3. FILE MANAGEMENT 4. SYSTEM ERROR 5. PROTOCOL
2) Remove the protect pin. 3) Turn ON the power. 4) Enter the SIM 66-23 mode. 5) Press [START] key. During operation, "EXECUTING" is displayed. When the operation is completed normally, "COMPLETE" is displayed. If an error occurs, "FAIL" is displayed. 6) Turn OFF the power, and attach the protect pin.
(When 1)
66-26
SIMULATION 66-23 FAX PROGRAM DOWNLOAD. EJECT PROTECT PIN, AND PRESS START.
Setting Used to register external telephone numbers for Modem dial-in. (Only when FAX is installed) Not used in the market. (For development) FAX Data
Operation/Procedure
SIMULATION 66-23 FAX PROGRAM DOWNLOAD. EXECUTING
1) Enter the Modem dial-in FAX number (1 - 9, 0, *, #) with 10key. 2) Press [START] key.
SIMULATION 66-23 FAX PROGRAM DOWNLOAD. COMPLETE POWER OFF, AND SET PROTECT
SIMULATION 66-26 M-D-IN EXTEL NUMBER SETTING. 0-9:[0-9],*:[*],#:[#] INPUT NUMBER AND PRESS START. 0123456789*#01234567
PIN
66-27 Purpose Function (Purpose) Section Item Setting Used to register the transfer number for voice warp. (Only when FAX is installed) Not used in the market. (For development) FAX Data
Operation/Procedure 66-24 Purpose Function (Purpose) Section Item Clear Used to clear the FAST memory data. (Only when FAX is installed) FAX Data 1) Enter the voice warp transfer number (1 - 9, 0, *, #) with 10key. 2) Press [START] key.
SIMULATION 66-27 V-WP TRANSMIT NUMBER SETTING. 0-9:[0-9],*:[*],#:[#] INPUT NUMBER AND PRESS START. 0123456789*#01234567
Operation/Procedure 1) Select YES/NO of data clear. 1 2 YES NO FAST memory data is cleared. Not cleared.
66-29 Purpose Function (Purpose) Clear Used to clear data related to an address book (one-touch registration, program registration/ expansion, relay memory box registration, each table content). FAX, Network scanner Data
Section Item 66-25 Purpose Function (Purpose) Section Item Setting Used to register the FAX number for Modem dialin. (Only when FAX is installed) Not used in the market. (For development) FAX Data
Operation/Procedure 1) Select YES/NO of data clear. 1 2 YES NO Address book data is cleared. Not cleared.
Operation/Procedure 1) Enter the Modem dial-in FAX number (1 - 9, 0, *, #) with 10key. 2) Press [START] key.
SIMULATION 66-25 M-D-IN FAX NUMBER SETTING. 0-9:[0-9],*:[*],#:[#] INPUT NUMBER AND PRESS START. 0123456789*#01234567
manuals4you.com
66-30 Purpose Function (Purpose) Section Item Operation test/Check Used to check the change in the TEL/LIU status. (Only when FAX is installed) FAX Operation
66-33 Purpose Function (Purpose) Section Item Operation test/Check Used to check the signal (BUSY TONE/CNG/ CED/FNET/DTMF) detection. (Only when FAX is installed) FAX Operation
Operation/Procedure The TEL/LIU state is displayed. When the state is changed, it is highlighted. HS1 HS2 RHS EXHS Polarity reverse signal Polarity reverse signal Handset hook SW External telephone hook SW
FNET
DTMF
66-34 Purpose Function (Purpose) Section Item Operation test/Check Used to measure the communication time of test image data. (Only when FAX is installed) FAX Operation
1
66-31 Purpose Function (Purpose) Section Item Operation test/Check Used to check the relay operation. (Only when FAX is installed) FAX Operation
Operation/Procedure Communication test is performed to measure the time (ms). Send is made under the following conditions. Communication means Image quality Density ECM Sender record Memory send Normal text Light ON OFF
Operation/Procedure 1) Enter the number corresponding to the check item with 10key. 2) Press [START] key.
SIMULATION 66-31 TEL/LIU SETTING. INPUT 0-1, AND PRESS START. 1. MPXA 2. CION 3. MR 4. EC 5. S. 6. CML 7. DP 8.
1 2 3 4 5 6 7 8
10001100
66-32 Purpose Function (Purpose) Section Item Operation test/Check Used to check the receive data (fixed data) from the line. (Only when FAX is installed) FAX Operation
66-35 Purpose Function (Purpose) Section Item Setting Modem program rewriting. (Only when FAX is installed) Not used in the market. (For development) FAX Data
Operation/Procedure 1) Select YES/NO of Modem program reload. 1 2 YES NO Modem block reload is cleared. Not reloaded.
Operation/Procedure When check is completed normally, "OK" is displayed. In case of an error, "NG" is displayed. (Display message) CHECKING OK NG Checking Checking completed (OK) Checking completed (NG)
2) Press [START] key. When reload is completed normally, "OK" is displayed. In case of an error, "CHECK SUM" is displayed. The result of Modem reload is displayed. COMPLETE 81 82 83 84 NG Reload completed Check sum error Write error Delete error Verify error Due to loader NG
66-39
SIMULATION 66-35 MODEM PROGRAM RELOAD. ARE YOU SURE? 1. YES 2. NO
1
Press [START] key.
Setting Used to set the destination specifications. (Only when FAX is installed) FAX Specifications Operation
Operation/Procedure 1) Enter the number corresponding to the destination. 2) Press [START] key.
SIMULATION 66-39 FAX DESTINATION SETUP. SELECT 1-6, AND PRESS START 0. 1. 2. 3. 4. 5. 6. NO DESTINATION JAPAN U.S.A./CANADA EUROPE AUSTRALIA CHINA ASIA
Press [START] key.
SIMULATION 66-35 MODEM PROGRAM RELOAD. EXECITOMG LOADER xxxxx MODEM xxxxx
After completion of reloading
66-36 Purpose Function (Purpose) Section Item Operation test/Check Used to check interface between MFPC controller and MDMC. (Check of the data line or the command line) (Only when FAX is installed) FAX Operation
66-42 Purpose Function (Purpose) Section Item Setting PIC program rewriting (Only when FAX is installed) FAX Operation
Operation/Procedure 1) Enter the number corresponding to the check mode with 10key. 1 2 3 4 5 6 7 8 MFPC MDMC MFPC MDMC MFPC MDMC MFPC MDMC MFPC MDMC MFPC MDMC MFPC MDMC MFPC MDMC Date line once only Date line once only Data line repeat Data line repeat Command line once only Command line once only Command line repeat Command line repeat
Operation/Procedure 1) The confirmation window is displayed. Select whether rewriting of the program into PIC installed in the FAX VOX is performed or not. NOTE: Release the write protect notch. FAX program writing enabled (Jumpers and DIP SW depending on the model.) 1 2 YES NO Execution Cancel
2) Press [START] key. When check is completed normally, "OK" is displayed. Incase of an error, "NG" is displayed. When check is "repeat," the operation is continued until the result is NG or [CUSTOM SETTINGS] key is pressed.
SIMULATION 66-36 MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START. 1. 2. 3. 4. 5. 6. 7. 8. MFPC<-MDMC(DATA once) MFPC->MDMC(DATA once) MFPC<-MDMC(DATA repeat) MFPC->MDMC(DATA repeat) MFPC<-MDMC(CMD once) MFPC->MDMC(CMD once) MDPC<-MDMC(CMD repeat) MFPC->MDMC(CMD repeat)
Press [START] key.
2) Press [START] key. When reload is completed normally, "OK" is displayed. In case of an error, "NG" is displayed. NG cause: Write protect is set. PIC is not installed. Access error to PIC
SIMULATION 66-42 PIC PROGRAM RELOAD. ARE YOU SURE ? 1.YES 2.NO
Press [START] key.
SIMULATION 66-36 MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START. EXECUTING...
When check is "once" or "repeat" and the result is "NG":
SIMULATION 66-36 MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START. EXECUTING...(OK or NG)
manuals4you.com
66-43 Purpose Function (Purpose) Section Item Setting PIC adjustment value writing (Only when FAX is installed) FAX Operation
SIMULATION 66-43 PIC ADJUSTMENT VALUE WRITING. ENABLE WRITE PIN(for FAX PROGRAM ROM). SELECT 0-12, AND PRESS START. 0.WRITING for PIC 1.ci_level_judge 2 2.ci_cycle_min 10 3.ci_cycle_max 107 4.ci_range 5 5.ci_count 3 6.ci_detect 8 7.fnet_level_judge 1 8.fnet_range 3 9.fnet_time_out 100 10.fnet_count 3 11.poff_time 3 12.mswon_level_judge 3
Operation/Procedure To execute this simulation, FAX program writing must be allowed. (Jumpers and DIP SW depending on the model.) The adjustment values in PIC are changed or rewritten. 1) Enter the number corresponding to the set item with 10-key. 2) Press [START] key. 3) Enter the set value. 4) Press [P] key. 5) Select 0. 6) The confirmation window is displayed. Select whether the PIC adjustment values are written or not. YES NO The adjustment values are collectively written into PIC installed in the FAX BOX. No writing
SIMULATION 66-43 PIC ADJUSTMENT VALUE WRITING. INPUT VALUE 1-15, AND PRESS START. 1.ci_level_judge(1-15)
When writing of the PIC adjustment values is normally completed, OK is displayed. In case of an error, NG is displayed. Item 0 WRITING for PIC 1 ci_level_judge Content Set range Default Writing to PIC 1-15 2 Number of sensing until the CI signal level is setteld. ci_cycle_min CI signal cycle 0-254 10 min. Time ci_cycle_max CI signal cycle 0-254 107 max. time ci_range CI signal allowable 0-127 5 range ci_count CI signal 1-15 3 settlement number of times ci_detect CID IN- signal 1-15 8 settlement number of times 1-15 1 fnet_level_judge Sense number of times until settlement of FNET signal level fnet_range FNET signal 0-74 3 allowable range fnet_time_out FNET time out 76-255 100 time fnet_count FNET signal 1-15 3 settlement number of times poff_time PON signal OFF 0-15 3 time 2-15 3 mswon_level_judge Sense number of times until settlement of MSW_ON signal level
SIMULATION 66-43 PIC ADJUSTMENT VALUE WRITING. ARE YOU SURE ? 1.YES 2.NO
Select 1.
2 3 4 5
8 9 10
11 12
67
67-2 Purpose Function (Purpose) Operation test/Check Used to check the operation of the parallel I/F of the printer. (This simulation is for production only, and requires a special tool for execution. Not used in the market.) MFP controller Operation Interface/Communication
67-16 Purpose Function (Purpose) Section Item Operation test/Check Used to check the operation of the network card. MFP controller Operation
Interface/Communication
Operation/Procedure During check, "CHECKING" is displayed. When check is completed normally, "OK" is displayed. In case of an error, "NG" is displayed. (Display message) CHECKING OK NG Checking Check end (Normal) Check end (Error)
Section Item
Operation/Procedure (Display message) WAITING READY OK STAGE*NG Waiting Check start OK Check end (Normal) Check end (Error in stage *. *: 1 - 11)
Check end
SIMULATION 67-2 CENTRO PORT CHECK. CENTRO PORT: OK (or STAGE7 NG)
67-11 Purpose Function (Purpose) Section Item Setting Used to set YES/NO of the parallel I/F select signal of the printer. MFP controller Operation Interface/Communication
Operation/Procedure 1) Enter the number corresponding to the select IN signal YES/ NO setting with 10-key. Item 0 1 OFF ON Default 1
2) Press [START] key. When the printer parallel I/F is used and a trouble is generated in the communication between the PC and the printer, change the setting of this simulation.
SIMULATION 67-11 CENTRO SELECT IN SIGNAL SETTING. SELECT 0-1, AND PRESS START. 0. OFF 1. ON
manuals4you.com
LCD
MFP CONTROLLER
When the value is changed, it is sent and saved.
ENGINE CONTROLLER
SCANNER CONTROLLER
G Data saved by the PCU PWB Counters Drum rotation time counter (Accumulated time) Developer unit rotation time counter Toner supply time (Block IC CHIP) Drum rotating time (Block IC CHIP) Total counter Maintenance counter Developing counter Drum counter Toner cartridge counter Valid paper counter Tray 1 paper feed counter Tray 2 paper feed counter Tray 3 paper feed counter Tray 4 paper feed counter Manual paper feed counter ADU paper feed counter Staple counter Punch counter Main unit right-side paper exit counter Adjustment value Developing bias voltage value Cleaning mode developing bias voltage value Main high voltage adjustment Transfer charger voltage value Transfer belt cleaning voltage value Toner concentration reference value Density correction start set time (Developer unit) Density correction rotation time (Developer tank) Density correction amount (Developer tank) Correction execution direction, upper/lower limit (Developer tank) Toner concentration temperature correction (low temperature side) correction amount Toner concentration temperature correction (low temperature side) set temperature Toner concentration temperature correction (low temperature side) release temperature Toner concentration temperature correction (high temperature) correction amount Toner concentration temperature correction (high temperature side) judgment temperature Toner concentration temperature correction (high temperature side) judgment voltage Toner concentration temperature correction (high temperature side) correction value Toner concentration temperature correction (low temperature side) release time Toner concentration temperature correction (high temperature side) toner concentration delay time Multi-purpose width adjustment value Manual width adjustment value Heater lamp temperature (Center, normal control) Lead edge adjustment Led edge void set value Rear edge void set value Side edge setting Print off-center adjustment value Resist amount adjustment value Laser power adjustment value PPD1 sensor adjustment Process correction inhibit allow set value Developing bias rising correction wait time Developing bias rising correction adjustment value Built-in finisher jogger position adjustment Saddle adjustment value Other Serial number Trouble history Tray 1 size LCC size Manual destination information Tray 2 destination information Tray 1 paper remaining quantity data Tray 2 paper remaining quantity data Tray 3 paper remaining quantity data Tray 4 paper remaining quantity data Final toner concentration sensor output value Toner cartridge IC CHIP destination Counter mode setting White paper exit count setting Trouble memory mode setting Fusing operation mode (Prevention against curl) CE mark conforming operation mode Maintenance cycle Print stop setting when developer life over Saddle alignment operation priority mode PCU SOFT SW
G Data saved by the scanner control PWB Counters Scan counter SPF paper pass counter SPF stamp counter Adjustment value Document lead edge adjustment value Document off-center adjustment value Document image loss amount adjustment value Magnification ratio adjustment value SPF resist amount adjustment value Exposure motor speed adjustment value Platen document detection adjustment value SPF size width detection adjustment value Touch panel adjustment value Exposure level adjustment value change value OC/SPF exposure correction value Shading adjustment value (CCD/CIS) CCD shading start position adjustment value Other Exposure mode set value Scanner serial number Document image loss amount adjustment value Scanner soft SW
G Data saved by the MFP control PWB Counters Copy counter Printer counter FAX receive counter FAX send counter All valid paper counter Trouble counter JAM counter Adjustment value FAX SOFT SW., etc. Other Trouble history JAM history Destination setting Language setting Toner save mode setting 13" setting Auditor setting Counter mode setting Trouble memory mode setting Center binding mode AMS setting PC/MODEM communication trouble detection YES/NO setting Tag number set value Printers set values Network set value MFP soft SW
manuals4you.com
When using originals with two or three holes, place them so that the punched edge is at a position other than the feed slot.
Hole positions
Hole positions
Hole positions
Original size:
Document glass
Top
14 lbs. or 50g/m 2
34 lbs. or 128g/m 2
B. Total number of originals that can be set in the document feeder tray
Total aggregate thickness must not exceed 1/4" or 6.5 mm (for 14 to 21 lbs. or 50 to 80 g/m2 paper). 1/4" or 6.5 mm or less Total aggregate thickness must not exceed 3/16" or 5.0 mm (for 21 to 34 lbs. or 80 to 128 g/m2 paper). 3/16" or 5.0 mm or less
Bottom
Bottom
[Example 2]
Top Top
Bottom
Bottom
<Notes on use of the automatic document feeder> Use originals within the specified size and weight ranges. Use of originals out of the specified range may cause an original misfeed. Before loading originals into the document feeder tray, be sure to remove any staples or paper clips. If originals have damp spots from correction fluid, ink or glue from pasteups, be sure they are dried before they are fed. If not, the interior of the document feeder or the document glass may be soiled. Do not use the following originals. These originals may cause incorrect original size detection, original misfeeds, and smudges on copies. Transparency film, tracing paper, carbon paper, thermal paper or originals printed with thermal transfer ink ribbon should not be fed through the document feeder. Originals to be fed through the feeder should not be damaged, crumpled or folded or have loosely pasted paper on them or cutouts in them. Originals with multiple punched holes other than two-hole or three-hole punched paper may not feed correctly.
[Example]
Orientation of original Orientation of paper Copy after rotation
Face down
Face down
Stand/3 x 500 Upper Tray 2 sheet paper Middle Tray 3 drawer Lower Tray 4
Stand/MPD & Upper Tray 2 2000 sheet Lower Tray 3 paper drawer
If "AUTO-INCH" is selected in setting the paper type and paper size, the following paper sizes can be used with the automatic detection function: 11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R If "AUTO-AB" is selected in setting the paper type and paper size, the following paper sizes can be used with the automatic detection function: A3, B4, A4, A4R, B5, B5R, A5R, 8-1/2" x 13" Non-standard sizes Thick paper If "AUTO-INCH" is selected in setting the Special Labels, transparency film paper type and paper size, the following paper paper sizes can be used with the automatic (Refer to detection function: the next 8-1/2" x 11", 8-1/2" x 11"R page for If "AUTO-AB" is selected in setting the paper applicable type and paper size, the following paper special sizes can be used with the automatic papers.) detection function: A4, A4R, B5, B5R Non-standard sizes Postcard Japanese official postcard Envelopes can only be fed Applicable standard size envelopes: from the multi-purpose COM-10, Monarch, DL, C5, ISO B5, drawer. Applicable stock CHOKEI 3 weight for envelopes is 20 to Non-standard size 23 lbs. or 75 to 90g/m Same as multi purpose drawer Plain paper (Refer to the A. Applicable If "AUTO-INCH" is selected in setting the plain paper.) paper type and paper size, the following paper sizes can be used with the automatic detection function: 11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2" If "AUTO-AB" is selected in setting the paper type and paper size, the following paper sizes can be used with the automatic detection function: A3, B4, A4, A4R, B5, B5R, 8-1/2" x 13" Same as multi purpose drawer Plain paper (Refer to the next page for 8-1/2" x 11", A4 applicable plain papers.)
16 to 28 lbs. or 60 to 105g/m
16 to 28 lbs. or 60 to 105g/m
manuals4you.com
Normal position
Trouble Contents codes F1 02 Finisher transport motor abnormality Mail-bin stacker transport motor abnormality 03 Console finisher paddle motor trouble 06 Console finisher slide motor trouble 08 Finisher staple shift motor trouble 10 Finisher stapler motor trouble
Remark With Finisher installed With Mail bin stacker installed With Console Finisher installed With Console Finisher installed With Finisher installed With Finisher installed With Console Finisher installed With Finisher installed With Console Finisher installed With Mail bin stacker installed With Finisher installed With Console Finisher installed With Finisher installed With Console Finisher installed With Finisher installed With Console Finisher installed With Console Finisher installed With Console Finisher installed With Console Finisher installed With Console Finisher installed With Console Finisher installed With Console Finisher installed
PCU
PCU
PCU
PCU
Console finisher stapler motor trouble 11 Finisher bundle exit motor trouble Console finisher bundle exit motor trouble 12 Mail-bin stacker gate trouble
PCU
PCU PCU
PCU
SCANNER 15 Finisher lift motor trouble ICU PCU ICU ICU SCANNER
PCU
E7 01 System data trouble 02 Laser trouble 03 HDD trouble 06 Decode error trouble 10 Shading trouble (Black correction) 11
Console finisher lift motor trouble 19 Finisher front alignment motor trouble Console finisher front alignment motor trouble 20 Finisher rear alignment motor trouble Console finisher rear alignment motor trouble 30 Console finisher communication trouble
PCU
PCU
14
17
50 60 80
90
F1
00
When the scanner is installed Shading trouble (White When the correction all pixel scanner is adjustment) installed CCD communication trouble When the scanner is installed SPF scanning position adjustment trouble (Detected only when executing an adjustment SIM.) LSU connection trouble Controller skating trouble Communication trouble (ICU When the detection) between ICU and scanner is scanner installed Communication trouble (ICU When the detection) between ICU and scanner is PCU installed Finisher communication With trouble Finisher installed Mail-bin stacker With Mail communication trouble bin stacker installed
PCU
SCANNER
PCU
SCANNER
PCU
PCU
PCU ICU
31 Console finisher fold sensor trouble 32 Communication trouble between the console finisher and the punch unit. 33 Console finisher punch side registration motor trouble 34 Console finisher punch motor trouble 35 Console finisher punch side registration sensor trouble
PCU
PCU
ICU
PCU
PCU
PCU
PCU
PCU
manuals4you.com
38
39
40
80
81
87 F2 00 02 04 05 39 12 22 F6 00
F3
01
04
20
21
97
98
F7
01
H2 00 01 H3 00 01
Trouble detection With Console PCU Finisher installed With Console PCU Console finisher backup Finisher RAM trouble installed With Console PCU Console finisher punch Finisher backup RAM trouble installed Console finisher punch dust With Console PCU sensor trouble Finisher installed Console finisher punch With Console PCU power interruption trouble Finisher installed Finisher power abnormality With Finisher PCU installed Mail-bin stacker power With Mail bin PCU abnormality stacker installed With Console PCU Console finisher transport Finisher motor abnormality installed Finisher staple rotation motor With Finisher installed trouble Toner control sensor open/ PCU sensor trouble Toner supply abnormality PCU Improper cartridge (life cycle PCU error, etc.) CRUM error PCU Process thermistor trouble PCU Machine no. 1 tray lift-up PCU trouble Machine tray 2 lift-up trouble MultiPCU purpose tray Communication trouble (ICU When the ICU detection) between ICU and Fax board is FAX installed FAX expansion flash When the ICU memory abnormality (ICU Fax board is detection) installed FAX modem operation When the FAX abnormality Fax board is installed FAX write protect cancel When the FAX Fax board is installed Combination abnormality of When the FAX the TEL/LIU PWB and the Fax board is FAX soft switch installed FAX-BOX skating trouble When the FAX Fax board is installed When the FAX Combination error of the FAX-BOX destination Fax board is information and the machine installed destination information FAX board EEPROM read/ When the FAX write error Fax board is installed Thermistor open (HL1) PCU Thermistor open (HL2) PCU Fusing section high PCU temperature trouble (HL1) Fusing section high PCU temperature trouble (HL2) Remark
Trouble Contents Remark codes H4 00 Fusing section low temperature trouble (HL1) 01 Fusing section low temperature trouble (HL2) H5 01 5-time continuous POD1 notreaching jam detection L1 00 Scanner feed trouble When the scanner is installed L3 00 Scanner return trouble When the scanner is installed L4 01 Main motor lock detection 02 Drum motor lock detection 30 Controller fan motor lock detection L6 10 Polygon motor lock detection L8 01 No fullwave signal 02 Full wave signal width abnormality U1 01 FAX battery abnormality With FAX board installed 02 RTC read abnormality When the (common with FAX, on ICU Fax board is PWB) installed U2 00 EEPROM read/write error (ICU) 11 Counter check sum error (ICU) 12 Adjustment value check sum error (ICU) 22 SRAM memory check sum error (ICU) 23 SRAM memory individual data check sum error (ICU) 50 HD section individual data check sum error (ICU) 80 EEPROM read/write error When the (Scanner) scanner is installed 81 Memory check sum error When the (Scanner) scanner is installed 90 EEPROM read/write error (PCU) 91 Memory check sum error (PCU) U6 00 Desk/LCC communication With Paper trouble feed desk installed 01 Desk/LCC No. 1 tray lift-up With Paper trouble feed desk installed 02 Desk No. 2 tray/LCC1 lift-up With Paper trouble feed desk installed 03 Desk No. 3 tray/LCC2 lift-up With Paper trouble feed desk installed 10 Desk/LCC transport motor With Paper trouble feed desk installed U7 00 RIC communication trouble
SCANNER
PCU PCU
ICU
SCANNER
SCANNER
PCU
PCU
PCU
PCU
Controller
Contents Door open (CH ON) No developer cartridge No toner cartridge No drum cartridge Auto developer adjustment trouble (Over-toner) Auto developer adjustment trouble (Under-toner) Personal counter not installed RIC copy inhibit signal is received. Auditor not ready
Remark
Trouble detection PCU PCU PCU PCU PCU PCU Controller Controller Controller
E6
11
03
14
Details System data trouble When in data storage/acquiring of the HDD system area, the HDD responds an error and does not respond for 30sec, it is judged as a trouble. Cause The HDD is not properly installed to the ICU PWB. The HDD does not work for the ICU PWB. ICU PWB abnormality Check and Check installation of the HDD to the remedy ICU PWB. Check harness connection of the HDD from the ICU PWB. Use SIM62-2, 3 to check the HDD read/write. Replace the HDD. Replace the ICU PWB. Content Laser trouble Detail BD signal from LSU is kept OFF, or ON. Cause The connector of LSU or the harness in LSU is disconnected or broken. The polygon motor does not rotate normally. The laser home position sensor in LSU is shifted. The proper voltage is not supplied to the power line for laser. Laser emitting diode trouble PCU PWB trouble ICU PWB trouble Check and Check for disconnection of the LSU remedy connector. Use SIM 61-1 to check LSU operation. Check that the polygon motor rotates normally or not. Check light emission of laser emitting diode. Replace the LSU unit. Replace the PCU PWB. Replace the ICU PWB. Content HDD trouble Detail HDD connection failure If the HDD responds an error or does not respond for 30sec, it is judged as an error. (Other than the system area) Data abnormality in the file management area (when the cluster chain is broken) Cause HDD is not installed properly to the ICU PWB. HDD does not operate properly in the ICU PWB. ICU PWB trouble Check and Check installation of HDD to the ICU remedy PWB. Check connection of the harness of HDD to the ICU PWB. Use SIM 62-2, -3 to check read/write of HDD. Replace HDD. Replace ICU PWB.
manuals4you.com
10
11
14
17
Details Decode error trouble A decode error occurs during making of an image. Cause Data error during input from PCI to PM. PM trouble Data error during image compression/ transfer. ICU PWB abnormality Check and Check insertion of the PWB. (PCI bus) remedy If the error occurred in a FAX job, check installation of the FAX PWB. For the other cases, check the ICU PWB. Replace the ICU PWB. Content Shading trouble (Black correction) Details CCD black scan level abnormality when the copy lamp is off. Cause Abnormal installation of flat cable to CCD unit. CCD unit abnormality Scanner PWB abnormality Check & Check installation of CCD unit flat Remedy cable. Check CCD unit. Check scanner PWB. Content Shading trouble (White correction all pixel adjustment) Details CCD white reference plate scan level abnormality when the copy lamp is ON. Cause Abnormal installation of flat cable to CCD unit. Dirt on mirror, lens, white reference plate Copy lamp lighting abnormality Abnormal installation of CCD unit CCD unit abnormality Scanner PWB abnormality Check & Clean mirror, lens, and white reference Remedy plate. Check copy lamp light quantity (SIM 53) and lighting. Check CCD unit. Check scanner PWB. Content CCD communication trouble Details Communication trouble (clock sync) between scanner PWB and CCD-ASIC Cause Abnormal installation of harness to CCD unit CCD unit abnormality Scanner PWB abnormality Check & Check CCD unit harness. Remedy Check CCD unit. Check scanner PWB. Content SPF scanning position adjustment trouble (Detected only when executing an adjustment SIM.) Details The black Mylar which serves as the reference of the SPF scanning position is not detected. Cause Black Mylar installing failure on the SPF side Check & Check the SPF black Mylar. Remedy
60
80
90
F1
00
Details LSU connection trouble An LSU which does not conform to the machine is installed. Cause LSU connection trouble PCU PWB trouble LSU trouble Check and Check LSU PWB. Check PCU PWB. remedy Check connection of the connector and the harness between PCU and LSU. Content Controller skating trouble Detail Occurrence of an error in controller skating check Cause Discrepancy in the combination of the controller PWB and the ROM Check and Check the controller PWB. remedy Check the combination of the controller PWB and the ROM. Content Communication trouble (ICU detection) between ICU and scanner Details Communication establishment error/ Fleming/Parity/Protocol error Cause Defective connection of slave unit PWB connector Defective harness between slave unit PWB and ICU PWB Slave unit PWB mother board connector pin breakage Check & Check connector and harness of slave Remedy unit PWB and ICU PWB. Check grounding of machine. Content Communication trouble (ICU detection) between ICU and PCU Details Communication establishment error/ Fleming/Parity/Protocol error Cause Defective connection of slave unit PWB connector Defective harness between slave unit PWB and ICU PWB Slave unit PWB mother board connector pin breakage Check & Check connector and harness of slave Remedy unit PWB and ICU PWB. Check grounding of machine. Content Finisher communication trouble Detail Communication cable test error after turning on the power or exiting from SIM. Communication error with the finisher Cause Improper connection or disconnection of connectors and harness between the machine and the finisher. Finisher control PWB trouble Control PWB (PCU) trouble Malfunction by noises Check and Canceled by turning OFF/ON the remedy power. Check connectors and harness in the communication line. Replace the finisher control PWB or PCU PWB.
02
02
Details Mail-bin stacker communication trouble Communication cable test error after turning on the power or exiting from SIM. Communication error with the Mail-bin stacker. Cause Improper connection or disconnection of connector and harness between the machine and the Mail-bin stacker. Mail-bin stacker control PWB trouble Control PWB (PCU) trouble Malfunction by noises Check and Canceled by turning OFF/ON the remedy power. Check harness and connector in the communication line. Replace the Mail-bin stacker PWB or PCU PWB. Content Finisher transport motor abnormality Detail Transport motor drive trouble Cause Motor lock Drive abnormality Defective connection or disconnection between the PWB and the motor. Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble Check and Use SIM 3-3 to check the transport remedy motor operation. Content Mail-bin stacker transport motor abnormality Detail Transport motor trouble Cause Motor lock Drive abnormality Defective connection or disconnection between the PWB and the motor. Motor rpm abnormality Overcurrent to the motor Mail-bin stacker control PWB trouble Check and Use SIM3-21 to check the transport remedy motor operation. Content Console finisher paddle motor trouble Detail Paddle motor operation abnormality Cause Motor lock Motor rpm abnormality Overcurrent to the motor Console finisher control PWB trouble Check and Use SIM3-3 to check the motor remedy operation. Content Console finisher slide motor trouble Detail Slide motor operation abnormality Cause Motor lock Motor rpm abnormality Overcurrent to the motor Console finisher control PWB trouble Check and Use SIM3-3 to check the motor remedy operation.
10
10
11
03
11
06
12
Details Finisher staple shift motor trouble Staple motor drive trouble Motor lock Drive abnormality Defective connection or disconnection between the PWB and the motor. Home position sensor abnormality Motor rpm abnormality Finisher control PWB trouble Use SIM3-3 to check operations of the staple motor. Finisher stapler motor trouble Stapler motor operation abnormality Motor lock Defective connection or disconnection between the PWB and the motor. Home position sensor abnormality Motor rpm abnormality Overcurrent to the motor Console finisher control PWB trouble Use SIM3-3 to check the motor operation. Console finisher stapler motor trouble Stapler motor operation abnormality Motor lock Motor rpm abnormality Overcurrent to the motor Console finisher control PWB trouble Use SIM3-3 to check the motor operation. Finisher bundle exit motor trouble Bundle exit motor operation abnormality Motor lock Drive abnormality Defective connection or disconnection between the PWB and the motor. Home position sensor abnormality Motor rpm abnormality Console finisher control PWB trouble Use SIM 3-3 to check the bundle exit motor operation and the paddle solenoid operation, or use SIM 3-2 to check the boomerang rotations sensor. Console finisher bundle exit motor trouble Bundle exit motor operation abnormality Motor lock Motor rpm abnormality Overcurrent to the motor Console finisher control PWB trouble Use SIM3-3 to check the motor operation. Mail-bin stacker gate trouble Gate operation abnormality Gate lock Defective connection or disconnection between the PWB and the solenoid. Mail-bin stacker control PWB trouble Use SIM3-21 to check the transport gate operation.
manuals4you.com
15
19
19
Cause
20
20
Details Finisher lift motor trouble Lift motor operation abnormality Motor lock Motor rpm abnormality Overcurrent to the motor Finisher control PWB trouble Use SIM3-3 to check the lift motor operation. Console finisher lift motor trouble Lift motor operation abnormality Motor lock Drive abnormality Defective connection or disconnection between the PWB and the motor. Upper/lower limit sensor trouble Motor rpm abnormality Overcurrent to the motor Console finisher control PWB trouble Use SIM3-3 to check the motor operation. Finisher front alignment motor trouble Front alignment motor operation abnormality Motor lock Drive abnormality Defective connection or disconnection between the PWB and the motor. Home position sensor abnormality Motor rpm abnormality Finisher control PWB trouble Use SIM3-3 to check the motor operation. Console finisher front alignment motor trouble Front alignment motor operation abnormality Motor lock Motor rpm abnormality Overcurrent to the motor Console finisher control PWB trouble Use SIM3-3 to check the motor operation. Finisher rear alignment motor trouble Rear alignment motor operation abnormality Motor lock Drive abnormality Defective connection or disconnection between the PWB and the motor. Home position sensor abnormality Motor rpm abnormality Finisher control PWB trouble Use SIM3-3 to check the motor operation. Console finisher rear alignment motor trouble Rear alignment motor operation abnormality Motor lock Motor rpm abnormality Overcurrent to the motor Console finisher control PWB trouble Use SIM3-3 to check the motor operation.
Cause
31
32
33
34
35
Details Console finisher communication trouble Communication cable test error after turning on the power or exiting from SIM. Communication error with the console finisher Improper connection or disconnection of connector and harness between the machine and the console finisher. Console finisher control PWB trouble Control PWB (PCU) trouble Malfunction by noises Canceled by turning OFF/ON the power. Check connectors and harness in the communication line. Replace the console finisher control PWB or PCU PWB. Console finisher fold sensor trouble Sensor input value abnormality Sensor breakage harness breakage Console finisher control PWB trouble Use SIM3-2 to check the sensor operation. Communication trouble between the console finisher and the punch unit. Communication err between the console finisher and the punch unit. Improper connection or disconnection of connector and harness between the console finisher and the punch unit. Console finisher control PWB trouble Control PWB (PCU) trouble Malfunction by noise Canceled by turning OFF/ON the power. Check connectors and harness in the communication line. Replace the console finisher control PWB. Console finisher punch side registration motor trouble Punch side registration motor operation abnormality Motor lock Motor rpm abnormality Overcurrent to the motor Console finisher control PWB trouble Use SIM3-3 to check the motor operation. Console finisher punch motor trouble Punch motor operation abnormality Motor lock Motor rpm abnormality Overcurrent to the motor Console finisher control PWB trouble Use SIM3-3 to check the motor operation. Console finisher punch side registration sensor trouble Sensor input value abnormality Sensor breakage Harness disconnection Console finisher control PWB trouble Use SIM3-2 to check the sensor operation.
manuals4you.com
37
38
39
40
80
80
81
Details Console finisher punch timing sensor trouble Detail Sensor input value abnormality Cause Sensor breakage Harness disconnection Console finisher control PWB trouble Check and Use SIM3-2 to check the sensor remedy operation. Content Console finisher backup RAM trouble Detail Backup RAM contents are disturbed. Cause Console finisher control PWB trouble Malfunction by noise Check and Replace the console finisher control remedy PWB. Content Console finisher punch backup RAM trouble Detail Punch unit backup RAM contents are disturbed. Cause Punch control PWB trouble Malfunction by noise Check and Replace the punch control PWB. remedy Content Console finisher punch dust sensor trouble Detail Punch dust sensor detection trouble Cause When the punch dust sensor is not normally detected. Check and Sensor breakage remedy Harness disconnection Punch control PWB trouble Content Console finisher punch power interruption trouble Detail When power interruption of the punch unit is detected Cause Though 24V is supplied to the punch unit, the punch unit detects power interruption. Check and Harness disconnection remedy Punch control PWB trouble Content Finisher power abnormality Detail The 24V power is not supplied to the finisher PWB. Cause Improper connection or disconnection of connector and harness Finisher control PWB trouble Power unit trouble Check and Use SIM3-2 to check the sensor. remedy Content Mail-bin stacker power abnormality Detail The 24V power is not supplied to the Mail-bin stacker PWB. Cause Improper connection or disconnection of connector and harness Mail-bin stacker control PWB trouble Power unit trouble Check and Use SIM3-20 to check the sensor remedy operation. Content Console finisher transport motor abnormality Detail Transport motor trouble Cause Motor lock Motor rpm abnormality Overcurrent to the motor Console finisher control PWB trouble Check and Use SIM3-3 to check the motor remedy operation.
F2
00
02
04
05
39
Check and remedy Content CRUM error Detail Communication with IC chip cannot be made. Cause IC chip trouble IC chip contact failure Improper cartridge Check and Insert a proper cartridge. remedy Is the cartridge installed properly? Content Process thermistor trouble Detail Output value abnormality of the temperature sensor of temperature/ humidity sensor Cause Temperature/humidity sensor abnormality Temperature/humidity sensor harness connection failure PCU PWB trouble Check and Check connection of the harness and remedy the connector of the temperature/ humidity sensor. Replace the temperature/humidity sensor. Check PCU PWB.
Details Finisher staple rotation motor trouble Front staple rotation motor trouble Motor lock Drive abnormality Defective connection or disconnection between the PWB and the motor. Home position sensor abnormality Motor rpm abnormality Overcurrent to the motor Finisher control PWB trouble Use SIM3-3 to check the motor operation. Toner control sensor open/sensor trouble Toner control sensor output open Connector harness trouble Connector disconnection Sensor trouble Check connection of the toner control sensor. Check connection of connector and harness to the main PWB. Check for disconnection of harness. Replace the sensor. Toner supply abnormality Toner control sensor output value becomes under-toner too earlier. Connector harness trouble Toner concentration sensor trouble Toner cartridge trouble Check connection of the connector in the toner motor section. Check connection of connector and harness to the main PWB. Check for disconnection of harness. Toner concentration sensor output check SIM25-1. Replace the toner cartridge. Improper cartridge (life cycle error, etc.) An improper process cartridge is inserted. IC chip trouble Improper cartridge Insert a proper cartridge.
manuals4you.com
F3
12
F3
22
F6
00
01
Details Process humidity sensor breakdown Process humidity sensor open or short Temperature/humidity sensor harness connection failure Temperature/humidity sensor abnormality PCU PWB trouble Check and Check connection of the harness and remedy the connector of the temperature/ humidity sensor. Replace the temperature/humidity sensor. Check PCU PWB. Content Machine no. 1 tray lift-up trouble Detail LUD does not turn ON in the specified time. Cause LUD trouble No. 1 tray lift-up trouble Check connection of harness between the PCVU PWB, lift-up unit, and paper feed unit. Check and Check LUD, and their harness and remedy connectors. Check the lift-up unit. Content Machine tray 2 lift-up trouble Detail MCLUD does not turn ON in the specified time. Cause MCLUD trouble No. 2 tray lift-up motor trouble Harness disconnection f the PCU PWB, the lift-up unit, and the paper feed unit. Check and Check MCLUD, and their harness and remedy connectors. Check the lift-up unit. Content Communication trouble (ICU detection) between ICU and FAX Details Communication establishment error/ Fleming/Parity/Protocol error Cause Slave unit PWB connector disconnection Harness abnormality between slave unit PWB and ICU PWB. Slave unit PWB mother board connector pin breakage Slave unit ROM abnormality/No ROM/ Reverse insertion of ROM/ROM pin breakable Check & Check connector harness between Remedy slave unit PWB and ICU PWB. Check grounding of machine. Check slave unit PWB ROM. Content FAX expansion flash memory abnormality (ICU detection) Details Flash memory cannot be deleted. Cause Flash memory cannot be deleted. Check & Check the FAX image storage Flash Remedy memory. Use SIM 66-10 to clear the flash memory.
20
Cause
97
Content
Detail Cause
98
Content
Detail
Cause
Details FAX modem operation abnormality FAX PWB modem chip operation abnormality SW101 in the FAX PWB tries to perform normal operation on the boot side. Modem chip operation abnormality in FAX PWB Set SW101 on the FAX PWB to other than the boot side, and turn on the power again. Replace FAX PWB. FAX write protect cancel The write protect JP is released. The write protect JP is set to write allow. FAX interface PWB trouble FAX PWB trouble Check the write protect JP. Replace the FAX PWB. Replace the FAX interface PWB. Combination abnormality of the TEL/ LIU PWB and the FAX soft switch Combination abnormality of the TEL/ LIU PWB and the FAX PWB information (soft switch) Or the TEL/LIU PWB is not a new one for new MDMC PWB. The destination of the installed TEL/LIU PWB differs. The FAX PWB information (soft switch) differs. TEL/LIU PWB trouble Check the destination of the TEL/LIU PWB. Check the FAX PWB information (soft switch). Replace the TEL/LIU PWB. FAX-BOX skating trouble The FAX-BOX PWB is not one for the AR-FX12. (FAX detection) The FAX-BOX MODEM controller is not one for the AR-FX12. The FAX-BOX Modem controller PWB information (hard detection) is not for the AR-FX12. (The Modem controller PWB for the AR-FX5 or the AR-FX6 is used.) Check the FAX-BOX modem controller PWB. Replace it with a modem controller PWB for the AR-FX12. Combination error of the FAX-BOX destination information and the machine destination information Combination error of the FAX-BOX destination information and the machine destination information Because of improper combination between the destination information stored in the EEPROM on the FAXBOX PWB and that of the machine (set with SIM 26-6). Check the destination of the FAX-BOX. Check the machine destination with SIM 26-6. Use a proper combination of the machine and the FAX-BOX.
H2
H3
Details FAX board EEPROM read/write error EEPROM access error (read/write) EEPROM trouble FAX PWB EEPROM access circuit trouble Check & When replacing the EEPROM, use Remedy SIM66-4/5 (Signal send level) and SIM66-14/15/16 (Dial test) for adjustment. However, note that all the soft switches are reset to the initial values. No need to adjust when the PWB is replaced. 00 Content Thermistor open HL1 Fusing unit not installed Detail Thermistor is open. 01 (An input voltage of 2.92V or above is HL2 detected.) Fusing unit not installed Cause Thermistor trouble Control PWB trouble Fusing section connector disconnection AC power trouble Fusing unit not installed Check and Check harnesses and connectors from remedy the thermistor to the control PWB. Use SIM14 to clear the self diag display. Fusing section high temperature 00 Content trouble HL1 Detail The fusing temperature exceeds 01 242C. (An input voltage of 0.27V or HL2 above is detected.) Fusing temperature control is started, and 242C is detected three or more times continuously in sampling in the specified interval. (Every 300msec) Cause Thermistor trouble Control PWB trouble Fusing section connector disconnection AC power trouble Check and Use SIM5-2 to check the heater lamp remedy Blinking operation. If the heater lamp blinks normally: Check the thermistor and its harness. Check the thermistor input circuit in the control PWB. If the heater lamp keep lighting: Check the AC PWB and the lamp control circuit in the control PWB. Use SIM14 to cancel the trouble
H5
L1
L3
Details Fusing section low temperature trouble The set temperature is not reached within the specified time (3 min) after 01 turning on the power relay, or the HL2 temperature does not reach 80C within 80 sec. When the heater lamp is not turned off in the specified time (3 min) from starting warm-up, or the temperature does not reach 80C within 80 sec. After completion of warm-up operation, a temperature 50C lower than the temperature control level is detected 5 times continuously in sampling in the specified interval. (every 300msec) Cause Thermistor trouble Heater lamp trouble Control PWB trouble Thermostat trouble AC power trouble Interlock switch trouble Check and Use SIM5-2 to check the heater lamp remedy Blinking operation. If the heater lamp blinks normally: Check the thermistor and its harness. Check the thermistor input circuit in the control PWB. If the heater lamp does not light: Check for heater lamp disconnection and thermostat disconnection. Check the interlock switch. Check the AC PWB and the lamp control circuit in the control PWB. Use SIM14 to cancel the trouble. 01 Content 5-time continuous POD1 not-reaching jam detection Detail 5-time continuous POD1 not-reaching jam detection Cause A fusing section jam is not properly removed. (Jam paper remains.) POD1 sensor trouble, or harness disconnection Improper installation of fusing unit Check and Check jam paper in the fusing section. remedy (winding, etc.) Check POD1 sensor harness, and check the fusing unit installation. Use SIM14 to cancel the trouble. 00 Content Scanner feed trouble Details Scanner feed is not completed within the specified time. Cause Scanner unit abnormality Scanner wire disconnection Check & Check scanning with SIM 1-1. Remedy 00 Content Scanner return trouble Details Scanner return is not completed within the specified time. Cause Scanner unit abnormality Scanner wire disconnection Check & Check scanning with SIM 1-1. Remedy
manuals4you.com
Cause
02
Content Detail
Cause
30
Content Detail
Cause
L6
10
Content Detail
Cause
Details Main motor lock detection The motor lock signal is detected for 1.5sec during rotation of the main motor. main motor trouble Check connection of harness between the PCU PWB and the main motor. Control circuit trouble Use SIM25-1 to check the main motor operation. Check harness and connector between the PCU PWB and the main motor. Drum motor lock detection The motor lock signal is detected for 1.5sec during rotation of the drum motor. Drum motor trouble Improper connection of harness between the PCU PWB and the drum motor. Control circuit trouble Use SIM6-1 to check the drum motor operation. Check harness and connector between the PCU PWB and the drum motor. Controller fan motor lock detection The motor lock signal is detected during rotation of the controller fan motor. The motor lock signal is detected during rotation of the HDD fan motor. Fan motor trouble Improper connection of the harness between the controller PWB and the fan motor. Control circuit trouble Use SIM 6-2 to check the fan motor operation. Check the harness and the connector between the controller PWB and the fan motor. Polygon motor lock detection It is judged that the polygon motor lock signal is not outputted. Lock signal is checked in the interval of 10sec after starting the polygon motor, and it is judged that the polygon motor does not rotate normally. The LSU connector or harness in the LSU is disconnected or broken. Polygon motor trouble Use SIM61-1 to check the polygon motor operation. Check connector and harness connection. Replace LSU.
02
Content Detail
Cause
U1
01
02
U2
00
Details No fullwave signal Full wave signal is not detected. The PCU PWB connector or the power unit harness is disconnected or broken. PCU PWB trouble 12V power source trouble Check connection of the harness and connector. Replace PCU PWB. Replace the power unit. Replace the controller connection mother board. Full wave signal width abnormality It is judged as full wave signal frequency abnormality. (When the detection cycle is judged as 69Hz or above or 42.5Hz or below) The connector or harness of the PCU PWB and the power PWB is disconnected. PCU PWB trouble Power unit trouble Check connection of the harness and connector. Replace the PCU PWB. Replace the power unit. FAX battery abnormality FAX backup SRAM battery voltage fall Battery life Battery circuit abnormality Check that the battery voltage is about 2.5V or above. Check the battery circuit. RTC read abnormality (common with FAX, on ICU PWB) The value read from RTC on ICU PWB is [EE]h (abnormal). RTC circuit abnormality Battery voltage fall Battery circuit abnormality Set the time again with key operation, and check that time advances properly. Check RTC circuit. Check that battery voltage is about 2.5V or above. Check battery circuit. EEPROM read/write error (ICU) EEPROM write error EEPROM trouble EEPROM is not initialized. ICU PWB EEPROM access circuit trouble Check that EEPROM is properly inserted. Save the counter/adjustment values with the simulation. Use SIM16 to cancel U2 trouble. Replace the ICU PWB.
12
22
23
Content Detail
Cause
Details Counter check sum error (ICU) Counter data area check sum error EEPROM trouble Control circuit trouble by noise ICU PWB EEPROM access circuit trouble Check that EEPROM is properly inserted. Save the counter/adjustment values with the DIAG simulation. Use DIAG (SIM16) to cancel U2 trouble. Replace the ICU PWB. Adjustment value check sum error (ICU) Adjustment data area check sum error EEPROM trouble Control circuit trouble by noise ICU PWB EEPROM access circuit trouble Check that EEPROM is properly inserted. Save the counter/adjustment values with the simulation. Use SIM16 to cancel U2 trouble. Replace the ICU PWB. SRAM memory check sum error (ICU) MFPC section SRAM memory check sum error SRAM trouble Control circuit runaway due to noises ICU PWB SRAM access circuit trouble Initialize the communication management table registered in the SRAM and the FAX soft switch. Since the registered data are deleted, register the data again. Use SIM16 to cancel U2 trouble. Replace the ICU PWB. SRAM memory individual data check sum error (ICU) Check sum error for every data in the SRAM memory of the MFPC section (Communication management table, sender registration data, etc.) SRAM trouble Control circuit runaway due to noises ICU PWB SRAM access circuit trouble Automatically initialize the data related to the check sum error by turning OFF/ ON the power. Since the registered data are deleted, register the data again. Use SIM16 to cancel U2 trouble. Replace the ICU PWB.
80
81
90
91
Details HD section individual data check sum error (ICU) Detail Check sum error for every individual data in HD of the MFPC section (Onetouch, Group, Program, etc.) Cause HDD write/read error Control circuit runaway due to noises ICU PWB HD access circuit trouble Check and Automatically initialize the data related remedy to the check sum error by turning OFF/ ON the power. Since the registered data are deleted, register the data again. Use SIM 16 to cancel the U2 trouble. Replace the HD PWB. Replace the ICU PWB. Content EEPROM read/write error (Scanner) Details Scanner EEPROM write error Cause EEPROM abnormality Scanner PWB EEPROM access circuit abnormality Check & Check that EEPROM is set properly. Remedy Record counter/adjustment values with the simulation to protect the data from being deleted. Cancel U2 trouble with SIM 16. Replace scanner PWB. Content Memory check sum error (Scanner) Details Scanner memory check sum error Cause EEPROM trouble EEPROM which is not initialized is installed. Control circuit freeze by noises Scanner PWB EEPROM access circuit trouble Check & Check that EEPROM is set properly. Remedy Record counter/adjustment values with the simulation to protect the data from being deleted. Cancel U2 trouble with SIM 16. Replace scanner PWB. Content EEPROM read/write error (PCU) Detail PCU EEPROM write error Cause EEPROM trouble PCU PWB EEPROM access circuit trouble Check and Check that EEPROM is properly remedy inserted. Record counter/adjustment values with the simulation to protect the data from being deleted. Use SIM16 to cancel U2 trouble. Replace the Controller PWB. Content Memory check sum error (PCU) Detail PCU memory check sum error Cause EEPROM trouble EEPROM which is not initialized is installed. EEPROM is not initialized. PCU PWB EEPROM access circuit trouble Hang of control circuit due to noises Check and Check that EEPROM is properly remedy inserted. Save the counter/adjustment values with the simulation. Use SIM16 to cancel U2 trouble. Replace the Controller PWB.
manuals4you.com
Cause
01
02
03
10
Details Desk/LCC communication trouble Desk/LCC communication error Communication cable test error after turning on the power or exiting SIM. Improper connection or disconnection of connector and harness Desk control PWB trouble Control PWB (PCU) trouble Noise or interference Canceled by turning OFF/ON the power. Check connection of the harness and connector in the communication line. Desk/LCC No. 1 tray lift-up trouble Desk/LCC No. 1 tray lift-up trouble Sensor trouble Tray trouble Defective connection or disconnection between the PWB and the motor. Desk control PWB trouble Lift-up motor trouble Use SIM4-2 to check the upper limit sensor detection. Use SIM4-3 to check the lift-up motor operation. Desk No. 2 tray/LCC1 lift-up trouble Desk No. 2 tray/LCC lift-up trouble Sensor trouble Tray trouble Defective connection or disconnection between the PWB and the motor. Desk control PWB trouble Lift-up motor trouble Use SIM4-2 to check the upper limit sensor detection. Use SIM4-3 to check the lift-up motor operation. Desk No. 3 tray/LCC2 lift-up trouble Desk no. 3 tray lift-up trouble Sensor trouble Tray trouble Defective connection or disconnection between the PWB and the motor. Desk control PWB trouble Lift-up motor trouble Use SIM4-2 to check the upper limit sensor detection. Use SIM4-3 to check the lift-up motor operation. Desk/LCC transport motor trouble Desk/LCC transport motor operation trouble Motor lock Drive abnormality Defective connection or disconnection between the PWB and the motor. Motor rpm abnormality Overcurrent to the motor Desk control PWB trouble Use SIM4-3 to check the transport motor operation.
Cause
EE
EL
Content Detail
Cause
EU
Cause
PF
00
CE
00
01
Cause Check and remedy Content Another communication error occurs. Detail Communication error Cause Improper connection of the network cable Check and Check the connection of the network remedy cable. Content The print server card is broken down or is not installed. Detail Print server card connection trouble Cause The print server card is not installed on the controller. Print server card control PWB trouble Check and 1. Check that the print server card is remedy installed on the controller. 2. Output the NIC Config. Page to check the NIC version. 3. Replace the NIC.
Details RIC communication trouble RIC communication trouble Communication cable test error after turning on the power or exiting SIM. Disconnection of connector and harness RTC control PWB trouble Control PWB (ICU) trouble Noise or interference Canceled by turning OFF/ON the power. Check connector and harness in the communication line. Auto developer adjustment trouble (Over-toner) The toner concentration output is detected as 1.5V or below in the auto development adjustment. Toner concentration sensor trouble Charging voltage, developing voltage abnormality Insufficient toner concentration Developing unit trouble PCU PWB trouble Use SIM25-2 to perform auto developer adjustment. Auto developer adjustment trouble (Under-toner) The toner concentration output is detected as 3.5V or above in the auto development adjustment. Insufficient toner concentration Charging voltage, developing voltage abnormality Insufficient toner concentration Developing unit trouble PCU PWB trouble Use SIM25-2 to perform auto developer adjustment. RIC copy inhibit signal is received. Copy inhibit command from RIM (host) is received. Judged by the host. Inform to the host.
03
Content
Detail
Cause
04
Content Detail
Cause
05
Details The specified mail server or FTP server is not found. The specified mail server or the FTP server is not found. Improper connection of the network cable Network setup trouble An error occurs in the SMTP server/ FTP server/ NTS. 1. Check that the network cable is properly connected. 2. Check that the connected network supports TCP/IP protocol. 3. Check from the web page that the address of the FTP server or the desktop PC is properly set as the primary/secondary e-mail server address. 4. When the above address is described with the Hostname, check that the DNS server is properly set or not. 5. Check the SMTP server/ FTP server/ NTS for any trouble. The specified server suspends response during transmission of images. The specified server suspends response during transmission of images. Improper connection of the network cable An error occurs in the SMTP server/ FTP server/ NTS. 1. Check that the network cable is properly connected. 2. Check the SMTP server/ FTP server/ NTS for any trouble. The account name or the password for the FTP server is invalid. The entered account name of the FTP server or the password for authentication is invalid. Improper connection of the network cable Improper registration of the account name or improper password registered in the FTP server as the destination 1. Check that the network cable is properly connected. 2. Check the account name or the password registered in the FTP server as the destination. The directory of the FTP server is invalid. The entered directory of the FTP server is invalid. Improper connection of the network cable Check for existence of the directory name in the FTP server registered as the destination. 1. Check that the network cable is properly connected. 2. Check for existence of the directory name in the FTP server registered as the destination.
07
08
Details The specified mail server (POP3) is not found. Detail The specified mail server (POP3) is not found. POP3 server access error Cause Improper connection of the network cable Network setup trouble An error occurs in the POP3 server. Check and 1. Check connection of the network remedy cable. 2. Check that the connected network supports TCP/IP protocol. 3. Check on the Web page that the POP3 server address is correctly set. 4. When the above address is described with the Hostname, check that the DNS server is properly set or not. 5. Check for any error in the POP3 server. Content The entered account name of the POP3 server or the password for authentication is invalid. Detail The entered account name of the POP3 server or the password for authentication is invalid. POP3 server authentication check error Cause Improper connection of the network cable Improper account name or password registered in the POP3 server Check and 1. Check connection of the network remedy cable. 2. Check that the account name or the password registered for the POP3 server is correct. Content The specified mail server (POP3) is not found. Detail The specified mail server (POP3) is not found. POP3 server time out error Cause Improper connection of the network cable An error occurs in the POP3 server. Check and 1. Check connection of the network remedy cable. 2. Check for any error in the POP3 server.
manuals4you.com
Warning
Trouble
Trouble/Warning Trouble
Warning
A consumable part has reached its lifetime. YES Replace or supply the consumable part.
NO
Repair
Reset
Standby state
ma
ou.c y 4 s l a nu
om
Trouble content Scanner section breakdowns (Mirror motor, lens, copy lamp) FAX board breakdown FAX power OFF Network error Staple breakdown Paper feed tray breakdown PCU section breakdowns (Motor, fusing section, etc.) After-process breakdown Laser breakdown HDD breakdown CCD breakdowns (Shading, etc.) CIS breakdowns (Shading, etc.) Scanner communication trouble PCU communication trouble FAX backup battery voltage fall HDD registration data sum error Thermistor trouble (trouble history)
CE F1 (10) F3, U6 (LCC) C1, C2, C3, H2, H3, H4, PCU H5, L4 (excluding L4-30), L8, U2 (90, 91), F2 PCU F1 PCU E7 (02 only), L6 ICU E7 (03) Scanner E7 (10, 11, 14) Scanner E6 (10, 11, 14) ICU E7 (80) ICU E7 (90) ICU U1 (01, 02) ICU U2 (50) PCU F2 (39, 58)
G Troubles where the machine cannot be operated When a trouble occurs, the dialogue is displayed. OK button is not added to the trouble massage, and only setting can be performed. The message remains displayed until the trouble is canceled. Judgment block ICU ICU Operation enable mode Copy read Notification FAX Email FAX List (including Print to send receive print print interrupt) FASThost
Trouble content Memory External communication disable (RICA) Image memory trouble, decode error Skating check error Controller fan motor trouble
For FAX communication, refer to the (5) Communication specification when a trouble occurs. The machine may be operated under some conditions. 1: When detected except when in a job, the machine can be operated in the OC mode. 2: Can be operated except in the staple mode. 3: When detected except in a job, the machine can be operated except with the breakdown tray. 4: Can be operated with some restriction on the image quality depending on the destination. (Low density print) 5: When detected except in a job, can be operated except in the trouble paper exit section. 6: When detected except in a job, can be operated in the single surface scan mode.
manuals4you.com
When, however, a paper feed tray trouble is detected during a job, the engine is stopped and printing is disabled. 3: The display goes to the FAX status check menu and the list can be printed.: The received document is outputted. 4: Paper exit is enabled except for the trouble paper exit tray When, however, a paper feed tray trouble is detected during a job, the engine is stopped and printing is disabled. 5: Only the operation related to image quality can be executed depending on the destination. (low density print) 6: The operation can be executed in the single surface scanning mode.
The switches are set to the upper side (protect) in normal operation. When they are set to the lower side, the diag mode and write protect are released. (Refer to the figure below.) When writing each ROM, set the switches to the lower side. (Default: Upper side). Return the plate part which covers the DIP switch to the original position, and tighten the screw again.
Controller PWB DIP switch
2. Cautions
In this method, verify for each byte is not made in order to shorten the writing time. The reliability of writing is assured by comparing the sum value. If the operation should be abnormal, make updater (C.) by the controller PWB. When the power is turned off during writing, the process may be failed and the machine may not be booted. In this case, refer to E. Power OFF during update. After completion of update, the update window may be displayed by resetting the DIP switch on the controller PWB and booting the machine normally. In this case, the PCU and the scanner may not have been updated normally. Refer to F. Update window when normal booting. It takes a longer time (about 5 minute) to write to the PWBs on the PCU, the scanner, and the FAX ROM than to write by CN6 of the controller PWB. This is because the difference in the communication speeds of the PWBs, etc. Also when the version of the software which is updated is the same, the process may be completed quickly.
Screw (*)
Switch
Diag mode
Write protect
MENU key
OK key
manuals4you.com
B. Update procedure 1 (Writing with each ROM inserted to the specified slot)
In this case, the ROMs on the PCU, FAX, and the scanner must be operating ROMs. An empty ROM which cannot boot the machine cannot be used for writing.
C. Update procedures 2 (Writing to each ROM by use of CN6 of the controller PWB)
By use of an empty slot of the controller PWB, writing can be made to an empty ROM which is not operating.
(1) Preparation
1) Set the DIP switch on the back of the machine to the diag mode (lower side), and set the write protect switch to the release side (lower side). 2) Insert one of the ROMs of the PCU, the SCN, and the FAX into the empty slot (CN6) of the controller PWB. 3) Check to confirm that the scanner unit is connected with the machine. 4) Check to confirm that the FAX unit is connected with the machine. (When the FAX is installed.) 5) Connect the PC and the controller PWB with the Centronics cable or USB cable. 6) Turn on the power of the PC and the machine to be updated.
(1) Preparation
1) Set the DIP switches on the back of the machine to the diag mode (lower side) and the write protect switch to the release side (lower side). 2) Check to confirm that the scanner unit is connected with the machine. 3) Check to confirm that the FAX unit is connected with the machine. (When the FAX is installed.) 4) Connect the PC and the controller PWB with the Centronics cable or USB cable. 5) Turn on the power of the PC and the machine to be updated.
***
5) Reboot the machine, and use Up/Down key on the window of 1) to check to confirm that the version of the updated software has been updated. 6) Turn off the power, and reset the DIP switches to the upper side (normal side).
CN Update ***-> CN6 Result: OK 7) After turning off the power, replace the ROM to which writing is made with the ROM of the specified slot of the PWB, and turn on the power and check the operation and the version. (Use Up/Down key to check on the window of 1).) 8) Turn off the power, and reset the DIP switches to the upper side (protect side, normal side).
D. In case of Result: NG
(1) Possible causes of Result: NG
There are following possible causes of Result: NG. 1) The DIP switch of write protect is not set properly. The write protect switch of the controller PWB is not set to the release side (lower side). If the write protect switch is not set to the release side, data are not written into the ROM. Set the DIP switch properly, and retry updating. 2) The FAX cable is not connected. The FAX is NG. Writing is not made. Connect properly and retry writing. 3) In rare cases, the ROM is broken down. Check the ROM, and retry writing. If the trouble remains, replace the ROM. (* There are three types of ROM device: the common type for the PCU and the scanner, the common type for BOOT and MAIN, and the exclusive type for FAX.)
Update completed
Boot NG? NO
YES
manuals4you.com
NO
Rebootable?
YES
Remove the boot ROM and replace it with a spare. (If another ROM is NG, replace it, too.)
YES
Writing by CN6 of the controller PWB (C.)
Result: OK ?
Update completed
NO
Result: OK ? NO
YES
Update completed
NO
Rebootable?
YES
YES
Writing by CN6 of the controller PWB (C.)
Result: OK ?
Update completed
NO
Result: OK ?
YES
NO
Update completed
Enter the path of the transfer file to Input File Path. (Or press Reference button and select a file to be transferred.) Then select the target printer in Select Printer. Select a parallel port connection printer or a USB connection printer depending on the connection type. After completion of the above transfer file selection and the target printer setting, press Send button to transfer the file.
Write with onboard collective files (B.)
For the file transfer by USB connection, refer to <Reference> (3) File transfer by USB connection.
YES
[Setup]
1) Set the machine as a printer which is connected to the PC in a connection type other than USB. 2) Boot the machine in the diag mode conforming to the normal ROM update procedures. 3) Connect the PC and the machine with the USB cable. 4) The PC system detects a new hardware by Plug & Play function. 5) The driver of SHARP AR-M455N is automatically installed. (Note that the model name is displayed as SHARP AR-M455N regardless of the actual model name.) 6) Follow the normal ROM update procedures to bring the machine into the data reception status. 7) Execute File2PRN, specify the printer registered in procedure 7), and execute file transfer. (Example: SHARP AR-M455N SPDL2 on USB001)
Update completed
manuals4you.com
ADUM1 ORSPD ADUFM CRUM PWB POD1 POD2 POD3 DEVELOPER un TCS HUS-DV AR-MU2
(OPTION)
SCANNER OP PANEL un
ADUM2 HV DGS APOD APPD2 ADUSET MPFC MPED MPLD1 DVCH MPLS2 VFM1 VFM1 DSW-F DSW-L CFM2 VFM2 LEFT DOOR un DRAWER PWB CFM1 PCU PWB PSPS LSU un PGM LD PWB BD CCD PWB APIND APPD1 DSW-D MPFS MPWS MSS
(OPTION)
DELIVERY un POM
1. Block diagram
LVDS/INV PWB
TOUCH PANEL
CCFT
COIN VENDER
CIScnt PWB
PNC AUDITOR
SCNcnt PWB
ENGINE
SPOD
SOCD
SPFC
MIM
MHPS
SPWS
ORSLED
DESK/LCC [D27/D28]
INTER FACE PWB TAN Control PWB MCLUM TMM TLUM1 TLUM2 TPCL1 TSPD1 MPTLD PWB DH HEATER PWB DH-DSK1 DH-DSK2 TPFD2 T1SS PWB
* DH-DSK1,DSK2 :JAPAN only
LUD LCC[D28] MPT VR MCPCL TPFCL TPCL2 TSPD2 TTSD TPFD3 T2SS PWB MCSPD MCLUD TPFD1 TDRS MCPED PED CASETTE un LUM CSS PWB MAIN DRIVE un RRC TRC CPFC DM MM 3TRAY DESK [D27] DSK Control PWB MPT VR MCLUM MCPCL DMM DPFCL DPFD2 DPED1 DPFD3 DPED2 MCLUD DPFD1 DLUM1 DLUM2 DLUD1 DLUD2 DDRS DSPD1
SPFS
FILTER PWB
* FILTER PWB :JAPAN ,EX200
OCSW
SPLS1
SPLS2
SCOV
(OPTION)
SPPD MSW
FAX BOX [FX-12] FAXPWB FAX SW FAX DC/PS (OPTION) AR-FN6 AR-FN7 AR-MS1 (OPTION)
SPED
(OPTION)
DH-SCN1 DH-SCN2
AC IN
DPCL1 DPCL2
D1SS PWB
DSPD2
BOARD TO BOARD
CN201 BM12B-SRSS-TB 1 2 3 4 5 6 7 8 9 10 11 12 IMG_DOUT1_0 IMG_DOUT1_1 IMG_DOUT1_2 IMG_DOUT1_3 IMG_DOUT1_4 IMG_DOUT1_5 IMG_DOUT1_6 IMG_DOUT1_7 IMG_AREA1 GND2 AD_CLK GND2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
manuals4you.com
CN1 TX24-100R-LT-H1 1 GND2 2 GND2 3 /1_DBL4 /1_DBL+ 5 1_CLK6 1_CLK+ 7 1_DATA08 1_DATA0+ 9 1_DATA110 1_DATA1+ 11 GND2 12 GND2 13 GND2 14 GND2 15 GND2 16 GND2 17 (NC) 18 +12V1 19 +24V3 20 +24V3 21 PDSEL1 22 PDSEL2 23 /KEYIN 24 SEG0 25 GND2 26 GND2 27 LcdS+ 28 LcdS29 LcdM+ 30 LcdM31 LcdCP1+ 32 LcdCP133 LcdCP2+ 34 LcdCP235 LcdD0+ 36 LcdD037 LcdD1+ 38 LcdD139 LcdD2+ 40 LcdD241 LcdD3+ 42 LcdD343 GND2 44 GND2 45 YH 46 /XL 47 /STSET 48 /STMPS 49 GND2 50 GND2 51 GND2 52 GND2 53 +12V1 54 +12V1 55 GND2 56 +5V2 57 GND2 58 +5V2 59 GND2 60 +3.3V 61 FRM_CCD1 62 CLK_CCD1 63 TXD_CCD1 64 RES_CCD1 65 RXD_CCD1 66 ADD_CCD1 67 GND2 68 PAGE1 69 GND2 70 GND2 71 /CL1 72 PDSEL0 73 +5V2 74 PD 75 SEG1 76 SEG2 77 GND2 78 /F0 79 GND2 80 /F1 81 GND2 82 /F2 83 GND2 84 /F3 85 GND2 86 /BZR 87 GND2 88 +5V1 89 Lcd DIS 90 +3.3V 91 GND2 92 LCD-VEE 93 TH 94 /CCFT 95 /YL 96 XH 97 +24V3 98 +24V3 99 GND2 100 GND2
CN4 BM50B-SRDS-G-TF GND2 GND2 GND2 GND2 GND2 GND2 GND2 GND2 1_CLK+ 1_CLK1_DATA0+ 1_DATA01_DATA1+ 1_DATA1/1_DBL+ /1_DBLlcdDIS GND2 2_CLK+ 2_CLK2_DATA0+ 2_DATA02_DATA1+ 2_DATA1/2_DBL+ /2_DBLGND2 LcdD0+ LcdD0LcdD1+ LcdD1LcdD2+ LcdD2LcdD3+ LcdD3LcdM+ LcdMLcdS+ LcdSLcdCP1+ LcdCP1LcdCP2+ LcdCP2GND2 SLEEP LCD_VEE SCN_SET WAKE_UP GND2 FRDY 1 21 23 25 27 29 31 50 13 11 9 7 5 3 15 17 36 2 37 39 41 43 45 47 35 33 49 18 16 14 12 10 8 6 4 30 28 34 32 26 24 22 20 38 44 48 46 40 19 42
I/F PWB-CN 1 35 2 36 3 37 4 38 19 39 6 40 7 41 8 42 9 43 24 44 11 45 12 46 13 47 14 48 15 49 16 50 17 51 18 52 10 53 20 54
SD68M 1_CLK+ 1_CLK1_DATA0+ 1_DATA01_DATA1+ 1_DATA1/1_DBL+ /1_DBLlcdDIS GND2 2_CLK+ 2_CLK2_DATA0+ 2_DATA02_DATA1+ 2_DATA1/2_DBL+ /2_DBL/RES_SCN GND2 LcdD0+ LcdD0LcdD1+ LcdD1LcdD2+ LcdD2LcdD3+ LcdD3LcdM+ LcdMLcdS+ LcdSLcdCP1+ LcdCP1LcdCP2+ LcdCP2GND2 SLEEP LCD_VEE SCN_SET
CN3 BM30B-SRDS-G-TF 24 /RES_SCN 26 VCCW_SCN /RXD_SCN /TXD_SCN /DSR_SCN /DTR_SCN GND2 POF_SCN /RES_MFP GND2 +12V1 +12V1 GND2 +5V2 +5V2 +5V2 +5V2 +5V1 GND2 GND2 +24V3 GND2 +24V3 GND2 +24V3 GND2 GND2 GND2 GND2 GND2 27 23 25 21 14 28 19 22 16 15 13 12 11 10 9 20 18 17 5 7 3 8 4 6 1 2 29 30
21 55 22 56 23 57 27 58 25 59 26 5 60 61 28 62 29 63 30 31 64 65 32 34 33 67 66 68
VCCW_SCN WAKE_UP /RXD_SCN /TXD_SCN /DSR_SCN /DTR_SCN GND2 POF_SCN /RES_MFP GND2 +12V1 GND2 +12V1 GND2 +5V2 +5V2 +5V2 +5V2 +5V1 GND2 FRDY GND2 +24V3 GND2 +24V3 GND2 +24V3 GND2
Scanner (2/3)
LCD
GND2 (NC) (NC) (NC) (NC) GND2 LCD D3 LCD D2 LCD D1 LCD D0 GND2 LCD-VEE 3.3V Lcd DIS GND2 LCD CP2 GND2 LCD CP1 LCD M LCD S
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
CN4 20FLS-SM1-TB 1 GND2 2 (NC) 3 (NC) 4 (NC) 5 (NC) 6 GND2 7 LCD D3 8 LCD D2 9 LCD D1 10 LCD D0 11 GND2 12 LCD-VEE 13 3.3V 14 Lcd DIS 15 GND2 16 LCD CP2 17 GND2 18 LCD CP1 19 LCD M 20 LCD S
CN5 30FMN-BT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
XH /YL /XL YH /CCFT +24V3 GND2 TH GND2 LcdD3LcdD3+ LcdD2LcdD2+ LcdD1LcdD1+ LcdD0LcdD0+ LCD-VEE 3.3V LcdDIS GND2 LcdCP2LcdCP2+ GND2 LcdCP1LcdCP1+ LcdMLcdM+ LcdSLcdS+
LVDS PWB
FFC-4PIN
TOUCH PANEL
CCFT
/CCFT HV
1 2
ORS PD
BR LB PL BL BR GY
CN101 T24FAZ-SMT-TF 24 GND2 PDSEL0 23 PDSEL1 22 PDSEL2 21 +5V2 20 19 PD GND2 18 17 +5V2 /KEYIN 16 15 SEG0 14 SEG1 13 SEG2 12 /F0 11 /F1 10 /F2 9 /F3 GND2 8 GND2 7 6 GND2 5 (NC) 4 (NC) 3 /BZR 2 +5V1 1 GND2
CN4 T24FAZ-SMT-TF 1 GND2 2 PDSEL0 3 PDSEL1 4 PDSEL2 5 +5V2 6 PD 7 GND2 8 +5V2 9 /KEYIN 10 SEG0 11 SEG1 12 SEG2 13 /F0 14 /F1 15 /F2 16 /F3 17 GND2 18 GND2 19 GND2 20 (NC) 21 (NC) 22 /BZR 23 +5V1 24 GND2
CL1
1 2 3 4 5
STMP
manuals4you.com
MIM
CN5 B8B-PH-K-S 1 2 3 4 5 6 7 8
SCN cnt
BL GY LB RD BR LB
PWB
(2/3)
CN8 1-171825-2 1 +24V3 GND2 2 /CV_COPY 3 /CV_COUNT 4 /CV_START 5 /CV_CA 6 /CV_STAPLE 7 /CV_DUPLEX 8 /CV_SIZE0 9 /CV_SIZE1 10 /CV_SIZE2 11 /CV_SIZE3 12
CN9 B13B-PH-K-S /PNC /COPY /CA /READY /AUD +5V2 GND2 +24V3 (NC) /TC +24V3 PNC_a GND2 1 2 3 4 5 6 7 8 9 10 11 12 13 PHR-13 1 2 3 4 5 6 7 8 9 10 11 12 13
MHPS
Scanner (3/3)
CNC B26B-PHDSS-B +24V3 +24V3 GND2 GND2 +5V2 GND2 VAREF SPPD SPFC SPED SDSS SCOV SRRC SPWS SPFS 7 8 5 6 4 9 17 19 18 21 12 23 14 24 16 RD RD GY GY BL GY BL BR BR BR BR PL BR PL
SPF MOTOR
1754873+179228-3 BL 1 BR 2 GY 3 BL 1 PL 2 GY 3 BL 1 BR 2 GY 3
SPED
+5V1 SPED GND2 1754873+179228-3 +5V2 SCOV GND2 1754873+179228-3 +5V2 SPPD GND2
SCOV
SPPD
SMP-02V-NC+SMR-02V-N
SDSS
1 +24V3 2 /SDSS
RD 1 BR 2
PHNR-11-H+BU11P-TR-P-H BL BL 1 +5V1 11 BR BR 2 SPED 10 GY GY 9 3 GND2 BL BL 8 4 +5V2 PL PL 7 5 SCOV GY GY 6 6 GND2 BL BL 5 7 +5V2 BR BR 4 8 SPPD GY GY 3 9 GND2 RD RD 2 10 +24V3 BR BR 11 /SDSS 1
CNB B22B-PHDSS-B 5 +5V 16 1 7 18 2 8 14 3 11 15 9 4 20 10 22 6 12 19 13 17 21 SPED GND2 +5V2 SCOV GND2 +5V2 SPPD GND2 +24V3 /SDSS +5VPOD GND2 SPOD +5V2 SOCD GND2 +24V3 /SPFC +24V3 /SRRC (NC)
B3B-PH-K-S
SPOD
BL 1 GY 2 PL 3 BL 1 PL 2 GY 3 RD 1 BR 2 RD
SOCD
BL PL GY BL BR GY RD BR BL GY PL BL PL GY RD BR RD PL
SPFMO0 SPOD /SPFMA SOCD SPFMA SPLS1 /SPFMB SPLS2 SPFMB SPFSET GND2
3 25 2 26 1 22 11 20 13 15 10
PL PL PL PL BR BR BR PL PL PL GY
SPF PWB
SPFC SRRC
2 +24V3 1 /SPFC
SPFVR
SPLS1
SPLS2
BL 1 PL 2 GY 3
PHNR-2-H+BU2P-TR-P-H
SPFS
2 +24V3 1 /SPFS
RD 1 PL 2
CNA B12B-PHDSS-B 1 VAREF 2 SPWS 9 GND2 5 +5V2 4 SPLS1 12 GND2 7 +5V2 6 SPLS2 10 GND2 11 +24V3 3 /SPFS
c SRA-01T-3.2 a SRA-21T-3 GY GY
manuals4you.com
d GY SRA-51T-3 GY
e FG
SRA-51T-3
CN10 S28B-PHDSS RD RD GY GY BL BL GY BL BR BR BR BR BR PL BR PL GY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PL 19 PL 20 PL 21 PL 22 BR 23 BR 24 BR 25 PL 26 PL 27 PL 28 +24V3 +24V3 GND2 GND2 +5V1 +5V2 GND2 VAREF SPPD SPFC SPED SDSS SCOV SRRC SPWS SPFS GND2 GND2 SPFMO0 SPOD /SPFMA SOCD SPFMA SPLS1 /SPFMB SPLS2 SPFMB SPFSET CN7 S26B-PHDSS 2_DATA11 2_DATA1+ 2 2_DATA03 2_DATA0+ 4 2_CLK5 2_CLK+ 6 2_DBL7 2_DBL+ 8 9 GND2 10 FRM_CCD2 11 CLK_CCD2 12 PAGE2 13 ADD_CCD2 14 TXD_CCD2 15 RES_CCD2 16 RXD_CCD2 17 +3.3V 18 +3.3V 19 +24V3 20 GND2 21 +12V1 22 GND2 23 +5V2 24 GND2 25 +5V2 26 /CIS_SET VLED DGND VAS DGND VDS DGND SCN DGND LGATE DGND CLK DGND DATA DGND
LD
DGND SCLK DGND /LST DGND SD0 DGND SD1 DGND SD2 DGND SD3 DGND SD4 DGND SD5 DGND SD6 DGND SD7
CN3 9604S-35F 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
FF3-35-R15 35 VLED 34 DGND 33 VAS 32 DGND 31 VDS 30 DGND 29 SCN 28 DGND 27 LGATE 26 DGND 25 CLK 24 DGND 23 DATA 22 DGND 21 LD 20 DGND 19 SCLK 18 DGND 17 /LST 16 DGND 15 SD0 14 DGND 13 SD1 12 DGND 11 SD2 10 DGND 9 SD3 8 DGND 7 SD4 6 DGND 5 SD5 4 DGND 3 SD6 2 DGND 1 SD7
CIS un
manuals4you.com
CN2 B12B-PHDSS-B SD7 1 SD6 2 SD5 3 SD4 4 SD3 5 SD2 6 SD1 7 SD0 8 /LST 9 10 SCLK 11 GND2 12 GND2
b GY SRA-21T-3 FG
Engine (1/5)
BOARD to BOARD
CN1 TX25-80P-LT-H1 1 (NC) 2 (NC) 3 PCU_VCCW 4 (NC) 5 GND 6 GND 7 HSYNC 8 GND 9 GND 10 GND 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 DTEN GND GND GND VIDEO1 VIDEO0 GND GND +12V_FAN +12V2 +12V2 GND +3.3V2 +3.3V2 +3.3V2 +3.3V2 GND HDD-VCC HDD-VCC GND +5V1 +5V1 +5V1 +5V2 +5V2 GND +24V3 +24V3 GND +12V1 DTR_PCU DSR_PCU TXD_PCU RXD_PCU POF MSW_MON RES_PCU (NC) BUR_PR DCCNT HDDFAN_MON CNTFAN_MON PWM GND GND GND GND GND +12V_FAN +12V2 +12V2 GND +3.3V2 +3.3V2 +3.3V2 +3.3V2 GND HDD-VCC HDD-VCC GND +5V1 +5V1 +5V1 +5V2 +5V2 GND +24V3 +24V3 GND +12V1 CN2 SLD30R-1 30 +12V2 PCU_VCCW 29 GND DTR_PCU GND DSR_PCU GND TXD_PCU GND RXD_PCU POF MSW_MON GND RES_PCU GND HSYNC GND DTEN BUR_PR GND2 VIDEO1 VIDEO0 GND +5V1 +5V2 +5V2 +5V2 +5V2 +5V2 +12V1 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CN2 SLD30R-1 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 +12V2 PCU_VCCW GND DTR_PCU GND DSR_PCU GND TXD_PCU GND RXD_PCU POF MSW_MON GND RES_PCU GND HSYNC GND DTEN BUR_PR GND2 VIDEO1 VIDEO0 GND +5V1 +5V2 +5V2 +5V2 +5V2 +5V2 +12V1
RK-H401SD-0190 1 /RESET 2 GND2 3 DD7 4 DD8 5 DD6 6 DD9 7 DD5 8 DD10 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 DD4 DD11 DD3 DD12 DD2 DD13 DD1 DD14 DD0 DD15 GND2 KEY DMAREQ GND2 /DIOW GND2 /DIOR GND2 IORDY CSEL /DMACK GND2 INTRQ /ICCS10 DA1 /PDIAG/CBLID DA0 DA2 /CS0 /CS1 /DASP GND2
TX24-80R-LT-H1
(NC) (NC) PCU_VCCW (NC) GND GND HSYNC GND GND GND DTEN GND GND GND VIDEO1 VIDEO0 GND GND +12V_FAN +12V2 +12V2 GND +3.3V2 +3.3V2 +3.3V2 +3.3V2 GND HDD-VCC HDD-VCC GND +5V1 +5V1 +5V1 +5V2 +5V2 GND +24V3 +24V3 GND +12V1 DTR_PCU DSR_PCU TXD_PCU RXD_PCU POF MSW_MON RES_PCU (NC) BUR_PR DCCNT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
HDD
PCU PWB
T T G /S G G G L V G G T V /V /L G G + G + + + /V G /S /V /P /R G G + G
HDDFAN_MON 51 CNTFAN_MON 52 53 PWM 54 GND 55 GND 56 GND 57 GND 58 GND 59 +12V_FAN 60 +12V2 61 +12V2 62 GND 63 +3.3V2 64 +3.3V2 65 +3.3V2 66 +3.3V2 67 GND 68 HDD-VCC 69 HDD-VCC 70 GND 71 +5V1 72 +5V1 73 +5V1 74 +5V2 75 +5V2 76 GND 77 +24V3 78 +24V3 79 GND 80 +12V1
FM_HDD
FM_CNT
manuals4you.com
U B
CN3 24FMN-BIRK-A RS 1 R/W 2 EN 3 D0 4 D1 5 D2 6 D3 7 D4 8 D5 9 D6 10 D7 11 +5V1 12 +5V1 13 GND2 14 GND2 15 KEY1 16 KEY2 17 KEY3 18 KEY4 19 KEY5 20 KEY6 21 LED1\ 22 LED2\ 23 LED3\ 24
LSU UNIT
CN2 S32B-PHDSS-B 45 sheets (35 sheets) BR BR GY BR GY GY GY BR BR GY GY BR BR LBR BR GY GY BL GY BL RD RD BR GY BR BR BR BR GY GY BL GY 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 TEST3 TEST2 GND2 /SYNC GND2 GND2 GND2 LSU_S/H VRB GND2 GND2 TEST VIDEO /VIDEO /LDON GND2 GND2 +5V2 GND2 +5V2 +24V1 +24V1 /VFM1 GND2 /START /VFM1 /PMCLK /READY GND2 GND2 +5V LD GND2 CN1 S11B-PH-K-S 45 sheets (35 sheets) +24V1 11 VFM1\ 10 GND2 9 +24V1 8 VFM1\ 7 GND2 6 +24V1 5 PMCLK\ 4 READY(READY\) 3 START\ 2 GND2 1
CN16 S32B-PHDSS-B TEST3 TEST2 GND2 /SYNC GND2 GND2 GND2 LSU_S/H VRB GND2 GND2 TEST VIDEO /VIDEO /LDON GND2 GND2 +5V2 GND2 +5V2 +24V1 +24V1 /VFM1 GND2 /START /VFM1 /PMCLK /READY GND2 GND2 +5V LD GND2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
VFM1
POWER SOURCE SECTION
VFM1
LSU
PHR-5 1 PMCLK 2 READY 3 START\ 4 GND2 5 +24V1 CN3 S4B-PH-K-S GND2 SYNC\ GND2 +5V2 BR 1 LB 2 BR 3 BL 4 CN1 B4B-PH-K-S 4 GND2 3 SYNC\ 2 GND2 1 +5V2
PM
BD
Engine (2/5)
NO ASSEMBLY
CN6 9604S-08C 1 DSW-F 2 DSW-F 3 GND2 4 GND2 5 DM\ 6 DM-T 7 DMCLK\ 8 (NC) CN19 B4B-PH-K-S POM2 1 POM0 2 POM3 3 POM1 4 CN20 B4B-PH-K-S POM1\ 1 POM3\ 2 POM0\ 3 POM2\ 4 (NC) 5
MAIN DRIVE
DM
8 7 6 5 4 3 2 1
NO ASSEMBLY
TONER HOPPER
8FE-ST-VK-N DSW-L DSW-L GND1 GND1 +5V2 GND2 MM\ MM-T
TM1
1 2
MAIN DRIVE
MM
8 7 6 5 4 3 2 1
CN9 9604S-08C 1 DSW-F 2 DSW-F 3 GND2 4 GND2 5 +5V2 6 GND2 7 MM\ 8 MM-T
PCU
TONER HOPPER
CRU PWB PSPS
TSR-04V-K GND2 +5V2 CRUCLK CRUSDA 1 2 3 4 BR GY BL BR BR RD CN5 B8B-PH-K-S 1 GND2 2 +5V2 3 CRUCLK 4 CRUSDA 5 PSPS\ 6 +24V1 7 (NC) 8 +24V1
PWB
DEVELOPER UNIT
QR/P8-12S-C(01) DVCH1 1 DVCH2 2 BR DVCH3 3 BR TH-DV 4 GY GND2 5 GND2 6 BR TCS 7 GY GND2 8 RD +24V1 9 BL +5V2 10 BR HUS-DV 11 WH DVBias 12 1 2 3 4 5 6 7 8 9 10 11 WH 12 #187 Bias BR BR BR BR GY GY BR GY RD BL BR CN8 B11B-PH-K-S 1 DVCH1 2 DVCH2 3 DVCH3 4 TH-DV 5 GND2 6 GND2 7 TCS 8 GND2 9 +24V1 10 +5V2 11 HUS-DV
CN4 B32B-PHDSS-B /POMXB 1 +5V2 2 /POMB 3 POD1 4 /POMA 5 GND2 6 /POMXA 7 +5V2 8 +24V1 9 POD2 10 +24V1 11 GND2 12 GND2 13 +5V2 14 CFM2\ 15 POD3 16 +24V1 17 GND2 18 +24V1 19 CFM2\ 20 +24V1 21 VFM2\ 22 +24V1 23 GND2 24 (NC) 25 GND2 26 DSW-L 27 DSW-L 28 (NC) 29 (NC) 30 (NC) 31 DSW-F 32
BR BL BR BR BR GY BR BL RD BR RD GY GY BL BR BR GY
RD RD GY
RD RD
RD
TCS
51021-0400 (NC) 1 +24V1 2 TCS 3 GND2 4 ZHR-4 +5V2 HUS-DV GND2 TH-DV
HUS-DV
1 2 3 4
SRA-21T-3 Bias
SHORT JIG
CN13 B24B-PHDSS-B GND2 1 +24V1 2 PED 3 CPFC\ 4 +5V2 5 +24V1 6 GND2 7 RRC\ 8 LUD 9 +24V1 10 +5V2 11 TRC\ 12 GND 13 CSS 14 GND2 15 GND2 16 PPD1 17 LUMB 18 +5V2 19 LUMA 20 CFM1\ 21 GND2 22 +24V1 23 GND2 24
GY RD BR BR BL RD GY BR BR RD BL BR BR GY GY BR BR BL BR BR GY RD GY
manuals4you.com
9 1 2 3 4 0 1 2 3 4 5
DELIVERY UNIT
SMR-06V+SMP-06V-NC BR BR 1 /POMXA 1 BR RD 2 2 /POMA BR BL 3 /POMB 3 BR YL 4 4 /POMXB RD WH 5 +24V1 5 RD BK 6 6 +24V1 SMP-03V-BC+SMR-03V-B BL BR 1 1 POD1 BR GY 2 2 GND2 GY BL 3 3 +5V2
POM
179228-3 BL 1 POD1 BR 2 GND2 GY 3 +5V2 179228-3 BL 3 +5V2 BR 1 POD2 GY 2 GND2 179228-3 BL 3 +5V2 BR 1 POD3 GY 2 GND2
POD1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
BR BL BR BR BR GY BR BL RD BR RD GY GY BL BR BR GY
POD2
POD3
DSW-L
RD SFPS-41T-187 RD SMR-03V-N 1 DSW-L 2 (NC) RD 3 DSW-F RD
SMR-03V-N+SMP-03V-NC
RD 1 2 RD 3
1 2 3
RD 1 2 3
DSW-F
SFPS-41T-187
RD
RD RD GY
CFM2
DUCT SECTION
RD RD
VFM2
DRAWER PWB
CFM1
HVR PWB
GY
PHNR-03-H+BU03P-TR-P-H GY RD BR BR BL RD GY BR BR RD BL BR BR GY GY BR BR BL BR BR GY RD GY PHNR-09-H+BU09P-TR-P-H BL BL 1 +5V2 9 BR BR 2 PPD1 8 GY GY 3 GND2 7 BL BL 4 +5V2 6 BR BR 5 LUD 5 GY GY 6 GND2 4 BL BL 7 +5V2 3 BR BR 8 PED 2 GY GY 9 GND2 1 1 +5V2 2 PPD1 3 GND2 BL 3 BR 2 GY 1
PS ROLLER
179228-3(AMP) 1 +5V2 2 PPD1 3 GND2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
PPD1
HVR PWB
GY
LUD
PED
CASETTE UNIT
BR GY BR BR CN1 S4B-PH-K-S 1 CSS 2 GND2 3 LUMB 4 LUMA
LUM
PHNR-02-H+BU02P-TR-P-H BR 1 CPFC\ 2 RD 2 +24V1 1 PHNR-02-H+BU02P-TR-P-H BR 1 RRC\ 2 RD 2 +24V1 1 PHNR-03-H+BU03P-TR-P-H BR 1 TRC1\ 3 2 (NC) 2 RD 1 3 +24V1
MAIN DRIVE
09R-RWZV-K2GGP4+CZHR-05V-S
B-5
GY GY GY GY
SMP-04V-NC+SMR-04V-N
BR GY BR GY 1 2 3 4
BR 1 2 3 4 GY BR GY
WH 1 2 3 4 WH BK GY
VLP-03V+VLR-03V
1 2 3
HL1N HL2N L
WH 1 2 3 WH BK
CN2 B7B-PH-K-S +24VPR (NC) CN1 B03P-VL HLPR HLCNT1 HLCNT2 MSW MON DCCNT/
1 2 3 4 5 6 7
HL2 SRA-51T-4
BK
1 2 3
HL1N HL2N L
FILTER PWB
CN1
BK
3 2 1 BK
TAIWAN ONLY
+24V2 #250(BK)
BK
AC/DC PWB
BK
WH
Nout #250(WH)
WH
Not
CN4
BK 1 2 WH
CN6 L (NC) N CN7 B2P-VH +5VOPT +5v1 B5P-VH GND2 GND2 GND2 +24V4 +5VOPT
2 1 2 3 4 5
BK
MSW
MSL #250(YL) MSN #250(YL) L #250(WH) N #250(WH)
3 WH
B03B-XASK-1
BK
WH
BK
WH
L1 #250(BL)
B2P3-VH
CN1
B2P3-VH-BK
CN2
1 MSW LIn
2 (NC)
3 MSW NIn
1 MSW Lout
2 (NC)
3 MSW Nout
WH Nout WH Nout BK BK
Lout Lout
RELAY PWB
#250(GR) Nin #250(GR) Nin
Lin
Lin
BK
BK
WH
WH
FUSE PWB
VLP-04V+VLR-04V
WH
BK
BK WH
1 2 3 4
N L Not Lot
WH 1 2 3 4 BK WH BK
WH
BK
BK
WH
ELP-02V+ELR-02VF
1 2
DH-L DH-N
1 2
to DESK UN
SIN-21T-1.8S DH-L SIN-21T-1.8S DH-N
BK
WH
AC IN
INLET
CN1 L L
BK
VLR-06V+VLP-06V-1
BK 1 YL/GR 2 BK 3 WH 4 YL/GR WH 5 6
L
BK 1 YL/GR 2 BK 3 WH 4 5 6 YL/GR WH
FAX POWER SW
L N
BK
B03P-VL 3 L
2 1
WH
WH
FG
FG
(NC) N
BK
N N
DCPR
N
WH
manuals4you.com
NO ASSEMBLY
CN14 B16B-PH-K-S
BR RD BR PL BR BR BR GY BR GY RD BR BR RD RD RD BL BR GY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
CN21 B8B-PH-K-R GND2 PCU_RES PCU-DSR PCU-RXD PCU-TXD PCU-DTR +5V2 (NC)
1 2 3 4 5 6 7 8
FW +24VPR HLPR +12V2 HLCNT1 HLCNT2 RTH1 GND2 RTH2 GND2 +24V1 /MSWPR MSW MON BUP_PR GND GND
PCU PWB
CN15 9604S-14F DSW-F GND2 GND2 DHVREM MHVREM\ THV+PWM\ GBPWM\ DHVPWM\ THV-PWM\ DVREM\ DVPWM\ THVREM\ MHV-T THin
1 2 3 4 5 6 7 8 9 10 11 12 13 14
1-84432-4(AMP)
14 13 12 11 10 9 8 7 6 5 4 3 2 1
DSW-F GND2 GND2 DHVREM MHVREM\ THV+PWM\ GBPWM\ DHVPWM\ THV-PWM\ DVREM\ DVPWM\ THVREM\ MHV-T THin
BL
PS-187
RD
SRA-21T-4L
RD
MHV
OR OR GY GY GY GY BR OR 6 OR 7 GY 8 GY 9 RD 1 RD 2 GY 3 4 5
PS-187
WH
SRA-21T-3
WH
THV
PS-187
SRA-21T-4L
WH
HV
YL
GB
PS-187
SRA-21T-3
RD
DHV
PS-187
GR
DV
BIAS
CN23 173981-2
1 2
XPNC +24V1
ELR-04NVF
GY 1 GY 2 RD 3 BL 4
to DESK UN
Mother PWB
ELP-06V-NV+ELR-06N
BL BL GY RD BR 1 2 3 4 5 6
CN3 V9PS-VH
1 2 3 4 5 6 BL BL GY RD BR 1 2 3 4 5 6 7
PL
8 9
1 2 3 4
GY GY BL
D del only)
BK
L
WH
FAX DCPS
N
09R-RWZV-K2GGP4+CZHR-05V-S
B-5
GY GY GY GY
SMP-04V-NC+SMR-04V-N
BR GY BR GY 1 2 3 4
BR 1 2 3 4 GY BR GY
WH 1 2 3 4 WH BK GY
VLP-03V+VLR-03V
1 2 3
HL1 HL2 L2
1 2 3
AC/DC PWB
BK BR WH
CN2 B7B-PH-K-S +24VPR (NC) HLPR HLCNT1 HLCNT2 MSW MON DCCNT/
1 2 3 4 5 6 7
HL2 SRA-51T-4
BK
FILTER PWB
HL-1N CN2 B03P-VL HL-2N HL-L L2 (NC) CN1 B2P4-VH (NC) L2R
1 2 3 1 2 3 4
CN1 B03P-VL
1
WH WH BK BK 2 3
HL1 HL2 L2 L L2R #187(BK) #187(BK) CN5 B12P-HL-A +24V1 +24V2 +24V3 +5V1 +5VOPT +3.3V1
RD 1 RD 2 RD 3 BL 4 5 OR 6 OR 7 GY 8 GY 9 10 11 12 GY GY BR
BK
BK
+3.3V1 Lot #250(BK) #250(BK) #250(WH) #250(WH) GND2 GND2 Lout GND2 GND2 Nout FW CN6 B5P-VH CN7
1 2
BK
WH
WH
Not CN4
BK
1 2 3 4 5
L (NC) N
WH
MSW
BK
3 WH
MSL #250(YL)
BK
L #250(WH)
BK
L1 #250(BL)
BK
WH
BK
WH
B2P3-VH
CN1
B2P3-VH-BK
CN2
1 MSW LIn
2 (NC)
3 MSW NIn
1 MSW Lout
2 (NC)
3 MSW Nout
WH Nout WH Nout BK BK
Lout Lout
RELAY PWB
#250(GR) Nin
WH
Lin #250(GR)
BK
#250(GR) Nin
WH
FUSE PWB
VLP-04V+VLR-04V
WH
BK
BK WH
1 2 3 4
N L Not Lot
WH 1 2 3 4 BK WH BK
WH
BK
BK
WH
ELP-02V+ELR-02VF
1 2
DH-L DH-N
1 2
to DESK UN
SIN-21T-1.8S DH-L SIN-21T-1.8S
BK
AC IN
DH-N
WH
INLET
L L
BK
CN1 B03P-VL 3 L
2
VLR-06V+VLP-06V-1
BK 1 YL/GR 2 BK 3 WH 4 YL/GR WH 5 6
L
BK 1 YL/GR 2 BK 3 WH 4 5 6 YL/GR WH
FAX POWER SW
L N
BK
WH
WH 1
(NC) N
FG
FG
BK
N N
DCPR
N
WH
manuals4you.com
NO ASSEMBLY
CN14 B16B-PH-K-S
BR RD BR PL BR BR BR GY BR GY 1 2 3 4 5 6 7 8 9 10 11 12 BR RD RD RD BL BR GY 13 14 15 16
CN21 B8B-PH-K-R GND2 PCU_RES PCU-DSR PCU-RXD PCU-TXD PCU-DTR +5V2 (NC)
1 2 3 4 5 6 7 8
FW +24VPR HLPR +12V1 HLCNT1 HLCNT2 RTH1 GND2 RTH2 GND2 (NC) (NC) MSW MON BUP_PR GND GND
PCU PWB
CN15 9604S-14F DSW-F GND2 GND2 DHVREM MHVREM\ THV+PWM\ GBPWM\ DHVPWM\ THV-PWM\ DVREM\ DVPWM\ THVREM\ MHV-T THin
1 2 3 4 5 6 7 8 9 10 11 12 13 14
1-84432-4(AMP)
14 13 12 11 10 9 8 7 6 5 4 3 2 1
DSW-F GND2 GND2 DHVREM MHVREM\ THV+PWM\ GBPWM\ DHVPWM\ THV-PWM\ DVREM\ DVPWM\ THVREM\ MHV-T THin
BL
PS-187
RD
SRA-21T-4L
RD
MHV
OR OR GY GY GY GY BR OR 6 OR 7 GY 8 GY 9 RD 1 RD 2 GY 3 4 5
PS-187
WH
SRA-21T-3
WH
THV
PS-187
SRA-21T-4L
WH
HV
YL
GB
PS-187
SRA-21T-3
RD
DHV
PS-187
GR
DV
BIAS
CN23 173981-2
1 2
XPNC +24V1
ELR-04NVF
BL 1 RD 2 GY 3 GY 4
to DESK UN
Mother PWB
ELP-06V-NV+ELR-06N
BL BL GY RD BR 1 2 3 4 5 6
CN3 V9PS-VH
1 2 3 4 5 6 BL BL GY RD BR 1 2 3 4 5 6 7
PL
8 9
1 2 3 4
GY GY BL
D del only)
BK
L
WH
FAX DCPS
N
u an
yo 4 ls
o u.c
Engine (5/5)
CN12 B30B-PHDSS-B
1 2 3 4 5 6 7 8 9 10 11 12 13
CN10 B24B-PADES(BULE) +5V2 VAREF +24V2 GND2 GND2 MCPPD MCDRS MCPED MCLUD MCPWS MCSS1 MCSS2 MCSS3 MCSS4 MCSPD MC SET MCPCL\ MCFCL\ MCLUM\ MCM-T MCMCLK\ MCM\ MCPFS\ DCPR\
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
VAREF +5V3 +24V2 +24V2 GND2 GND2 ADMEN1\ ADMCK1\ ADMEN2\ ADMCK2\ MPFC\ MPFS\ DGS\ APID APOD APPD2 APPD1 MPLD1 MPED MPWS DSW-D ADU SET MPF SET MSS\ ADM H/L ADUFM\ MPLS2 MPLS1 (NC) (NC)
MULTICS
ADU
14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
PCU PWB
CN11 B22B-PADRS(RED) TXD-FIN1 RXD-FIN1\ DTR-FIN1\ DSR-FIN1\ RES-FIN1 GND2 TXD-FIN2 RXD-FIN2\ DTR-FIN2\ DSR-FIN2\ RES-FIN2 GND2 TXD-DSK RXD-DSK\ DTR-DSK\ DSR-DSK\ RES-DSK TRC-DSK\ FGS-FIN\ FM1\ DCPR\ +24V2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
DESK
manuals4you.com
OPTION (1/1)
CN11
B22B-PADRS PADP-22V-1-R TXD_FIN1 1 RXD_FIN1/ 2 DTR_FIN1/ 3 DSR_FIN1/ 4 5 RES_FIN1 6 GND2 7 TXD_FIN2 RXD_FIN2/ 8 9 DTR_FIN2/ DSR_FIN2/ 10 11 RES_FIN2 12 GND2 TXD_DSK 13 14 RXD_DSK/ 15 DTR_DSK/ DSR_DSK/ 16 17 RES_DSK TRC_DSK/ 18 FGS_FIN/ 19 (N.C) 20 (N.C) 21 (N.C) 22
PCU PWB
CN6
4 3 2 1
VHR-5N
B5P-VH 1 2 3 4 5
AR-D27,28
SRA-21T-3
DCPS
SRA-21T-4
Main body
CNB
1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 SMP-11V-BC SMR-11V-B
1 2 3 4 5 6 7 8 9 10 11
+24V_D P-GND +5V GND2 S-GND TXD_DSK RXD_DSK/ DTR_DSK/ DSR_DSK/ RES_DSK TRC_DSK
AR-FN6,MS1
CNA
VHR-5N / B5P-VH GND 1 GND 2 GND 3 +24V4 4 +5VOPT 5
1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 SMR-18V-N SMP-18V-NC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
+5V +24V_F GND2 S-GND P-GND F-GND TXD_FIN2 RXD_FIN2 DTR_FIN2/ DSR_FIN2/ RES_FIN2 FGS_FIN/ +24V_F +24V_F P-GND P_GND S_GND (N.C)
AR-FN7
Power I/F PWB UN
1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 ELP-12V ELR-12V 1 2 3 4 5 6 7 8 9 10 11 12 TXD_FIN1 RXD_FIN1/ DTR_FIN1/ DSR_FIN1/ RES_FIN1 +24V_F +5V GND2 S-GND F-GND +24V_F P-GND
OPTION I/F UN
DESK
ELP-02V+ELR-02VF DH-L 1
2
BK BK WH
1 2
DH-N
1 2 WH 3
Main Body
DH-HEATER PWB
manuals4you.com
SCN
ELR-02VF+ELP-02V 1 2 DH-L(DHSW) DH-N(SCN) 1 2 BK 1 WH 2 1 2 WH 3 BK CN-C B2P3-VH DH-L(DHSW) (NC) DH-N(SCN)
ELP-02V+ELR-02V
BK
1 DH-L(DHSW)
DH_DH1 AC CABLE
WH
2 DH-N(SCN)
DH_DH2
BK WH
ADU upper-stream section paper pass detection ADU lower-stream section paper pass detection Changeover between the power save mode and the normal power mode Communication CLK CRUM communication CLK Communication data/ CRUM communication address signal data/address signal Paper tray insertion Paper tray insertion detection signal detection OPC drum motor rotating OPC drum motor rotating speed control (CLK) signal speed control OPC drum motor lock OPC drum motor lock detection signal detection Serial communication Send control signal (serial control signal communication) ADU door sensor signal Door open/close detection Front door open/close Front door open/close detection signal detection
Left door open/close detection signal Control signal for serial communication DV unit identification signal 1 DV unit identification signal 2 DV unit identification signal 3 AC power full wave signal Flash write protect signal GND Fusing roller center section heater lamp control signal Fusing roller both sides heater lamp control signal Fusing heater lamp power relay control signal Horizontal sync signal Development humidity sensor Laser beam horizontal sync signal Paper tray upper limit detection signal Paper tray lift-up motor control signal Paper tray lift-up motor control signal
Left door open/close detection Receive control signal (Serial communication) Installation acknowledgment Installation acknowledgment Installation acknowledgment Power monitor Flash write protect GND Fusing roller center section heating control Fusing roller both sides heating control Fusing heater lamp power relay control Horizontal sync Humidity detection around the developing unit Laser beam horizontal position timing control Paper tray upper limit detection Paper tray lift-up control Paper tray lift-up control
14 14 2 8 16 13 13 13
6 3 15 11 8 9 20 18
Name MP tray upper limit sensor signal Multi-purpose paper feed tray transport motor lock signal Multi-purpose paper feed tray transport motor clock signal MP tray paper empty sensor signal MP tray width sensor detection MP tray paper remaining quantity sensor signal MP tray rear edge sensor 1 signal MP tray rear edge sensor 2 signal MP tray rear edge sensor 3 signal MP tray rear edge sensor 4 signal Main charger trouble detection signal Main motor lock detection signal ADU manual feed paper sensor signal Manual feed unit detection signal Manual feed paper length sensor signal ADU tray pull-out sensor signal ADU tray storing sensor signal ADU manual feed paper width detection signal Page signal
Function/Operation MP tray upper limit detection Multi-purpose paper feed tray transport motor lock detection Multi-purpose paper feed tray transport motor rotating speed control MP tray paper empty detection MP tray paper width detection MP tray paper remaining quantity detection MP tray rear edge size detection MP tray rear edge size detection MP tray rear edge size detection MP tray rear edge size detection Main charger trouble detection Main motor lock detection
Connector No. 10 10
Pin NO. 9 20
MCMCLK
10
21
PCU
MCPED MCPWS MCSET MCSPD MCSS1 MCSS2 MCSS3 MCSS4 MHV-T MM-T MPED MPFSET MPLD1 MPLS1 MPLS2 MPWS PAGE
Paper present
10 10 10 10 10 10 10 10 15 9 12 12 12 12 12 12 2
8 10 16 15 11 12 13 14 13 8 19 23 18 28 27 20 13
PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU
When pressed When pressed When pressed When pressed When pressed Trouble/ Without MHV Rotation
Normal Stop/Lock
Manual feed tray paper Paper present empty detection Manual feed unit detection Provided Not provided Manual paper feed tray paper length detection Manual feed extension tray pull-out detection Manual feed extension tray storing detection Manual feed paper width detection Print timing control to the controller (output for every page) Paper empty detection Paper present Pull out Storing
Paper tray empty sensor signal Polygon mirror motor drive clock signal Paper exit detection 1 signal Paper exit detection 2 signal Paper exit detection 3 signal Desk reset signal Finisher reset signal Finisher reset signal PCU reset signal Fusing roller temperature detection signal Fusing roller temperature detection signal
Paper empty
13 16 4 4 4
3 27 4 10 16
Polygon mirror motor drive clock Detection of paper exit Paper pass from the fusing section Paper exit paper pass Paper pass detection Detection of paper exit to Paper pass the upper section paper (Full detection) exit tray (Full detection) Desk reset Operation enable Finisher reset Operation enable Finisher reset Operation enable The controller resets the Operation PCU. enable Fusing roller temperature detection (Center section) Fusing roller temperature detection (Edge section)
11 11 11 2 14 14
17 5 11 17 7 9
manuals4you.com
Name Serial I/F data (DESK) Serial I/F data (FINISHER) Serial I/F data (FINISHER) Serial communication send data signal Toner concentration detection signal Developing temperature sensor N.C. Toner motor control signal
Function/Operation Serial I/F data (DESKPCU PWB) Serial I/F data (FINISHER-PCU PWB) Serial I/F data (FINISHER-PCU PWB) Send data to the controller
Connector level L H
Connector No. 11 11 11 2 8 8 15 7 7 11 11 11 2 16 2 2 16 12 12
Pin NO. 14 2 8 21 7 4 14 1 2 13 1 7 23 13 9 10 9 25 8
Toner concentration detection TH-DV Temperature detection around the developing unit THVin N.C. TMA Toner motor ON/OFF control TMB Toner motor control signal Toner motor ON/OFF control TXD_DSK Serial I/F data (DESK) Serial I/F data (PCU PWBDESK) TXD_FIN1 Serial I/F data Serial I/F data (PCU PWB (FINISHER) - FINISHER) TXD_FIN2 Serial I/F data Serial I/F data (PCU PWB (FINISHER) - FINISHER) TXD_PCU Serial communication Receive data from the receive data signal controller VIDEO Image signal Image signal to the LSU VIDEOinImage signal Image signal from the controller to the PCU PWB VIDEOin+ Image signal Image signal from the controller to the PCU PWB VRB Laser power control signal Laser power control XADM_H/L ADU motor current control ADU motor current control signal XADMCK1 ADU upper transport ADU upper transport motor clock signal motor rotation speed control XADMCK2 ADU lower transport ADU lower transport motor clock signal motor rotation speed control XADMEN1 ADU upper transport ADU upper transport motor control signal motor ON/OFF control XADMEN2 ADU lower transport ADU lower transport motor control signal motor ON/OFF control XADUFM ADU cooling fan control Cooling fan control signal XCFM1_PWM Suction fan control signal Suction fan control XCFM2PWM Ozone exhaust fan control Ozone exhaust fan control signal XCPFC Paper cassette paper feed Paper feed clutch control clutch control signal XDGS ADU gate solenoid control Gate select in duplex or signal paper exit XDHVPWM Separation high voltage Separation high voltage output control signal PWM control XDHVREM Separation high voltage Separation high voltage control signal ON/OFF control XDM OPC drum motor control OPC drum motor ON/OFF signal (ON/OFF) XDSR_DSK Serial communication Receive control control signal XDSR_FIN1 Serial communication Receive control control signal XDSR_FIN2 Serial communication Receive control control signal XDTR_DSK Serial communication Send control control signal
PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU
12
10
PCU
12 12 12 13 4 4 13 12 15 15 6 11 11 11 11
7 9 26 21 15 20 4 13 7 4 5 16 4 10 15
PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU
Name Serial communication control signal Serial communication control signal Developing bias voltage control signal (PWM) Developing bias control (ON/OFF) signal Finisher gate solenoid control signal Fan Main charger grid bias voltage (PWM) control signal Laser ON/OFF control signal MP door open/close sensor signal Multi-purpose paper feed tray transport clutch Multi-purpose paper feed tray lift-up motor Multi-purpose paper feed tray transport motor control signal Multi-purpose paper feed clutch MP transport sensor signal Main charger control signal Main motor control signal
Function/Operation Send control Send control Developing bias PWM control Developing bias ON/OFF Finisher gate solenoid control Fan Main charger grid bias voltage (PWM) control Laser ON/OFF control MP left door open/close detection Clutch for transport from the MP tray MP tray lift up Multi-purpose paper feed tray transport motor ON/ OFF control Clutch for paper feed from the MP tray Paper detection on the path Main charger ON/OFF
Connector No. 11 11 15 15 11 11 15
Pin NO. 3 9 11 10 19 20 8
PWB Remark name PCU PCU PCU PCU PCU PCU PCU
ON Paper transport Up ON
16 10 10 10 10
15 7 18 19 22
17 6 5 7 11
XMPFS
XMSS XMSWMON XMSWOFF XMSWPR XPNC XPOF XPOMA XPOMB XPOMXA XPOMXB XPPD1 XPSPS XREADY XRRC XRSVOUT2 XSTART
Main motor ON/OFF control ADU manual feed paper Clutch for paper feed from feed clutch control signal the manual paper feed tray ADU manual feed paper Solenoid for paper feed feed solenoid control from the manual paper signal feed tray ADU shutter solenoid Shutter open/close control control signal in manual paper feed MSW monitor signal Main switch monitor MSW OFF signal Main switch OFF signal Main switch power relay Main switch power relay control signal control Mechanism counter Mechanism counter Power OFF status signal Power OFF status Paper exit motor control Paper exit unit paper signal (Phase A) transport Paper exit motor control Paper exit unit paper signal (Phase B) transport Paper exit motor control Paper exit unit paper signal (Phase /A) transport Paper exit motor control Paper exit unit paper signal (Phase /B) transport Resist roller front paper Detection of paper pass in pass detection signal front of the resist roller Separation solenoid Separation solenoid control signal control LSU motor READY signal LSU motor READY detection Resist roller clutch control Resist roller clutch ON/ signal OFF control Reserved Reserved Polygon mirror motor drive Polygon mirror motor start signal control
Paper feed
12
12
PCU
Paper feed Relay ON Power OFF Paper pass Separation Paper transport ON
12 14 2 14 23 2 4 4 4 4 13 5 16 13 5 16
24 13 19 12 1 20 5 3 7 1 17 5 28 8 7 25
PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU
manuals4you.com
Function/Operation LSU horizontal sync detection (BD sensor signal) Transfer charger output control (PWM control) Transfer charger output control (PWM control) Transfer charger ON/OFF control Paper transport roller ON/ OFF control Paper transport timing Cooling fan control Heat exhaust fan control Image signal to the LSU
Connector level L H
Connector No. 16
Pin NO. 4
XTHV+PWM
Transfer charger output control signal (THV+) XTHV-PWM Transfer charger output control signal (THV-) XTHVREM Transfer charger control signal (THV) XTRC Paper transport roller clutch control signal XTRC_DSK Paper transport timing signal XVFM1_PWM Cooling fan control signal XVFM2PWM XVIDEO Heat exhaust fan control signal Image signal
15 15 15 13 11 16 16 4 16
6 9 12 12 18 23 26 22 14
*1: Multi paper feed tray vertical size detection Multi paper feed tray 1 Multi paper feed tray 2 1 2 3 4 5 6 7 0 *2: Options M1SS1 M2SS1 L H H H L L L H Vertical size detection: Connector level M1SS2 M1SS3 M1SS4 M2SS2 M2SS3 M2SS4 L H L L H L L H H H L H L L L L L H L L L H H H Paper size AB series B5 A4 A5R B5R A4R Foolscap B4 A3 Inch series Extra LT INVR EX-R LTR Extra LGL WLT Tray not installed China series K16 A4 A5R K16R A4R Foolscap K8
manuals4you.com
No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
CV_SIZE3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
CV_SIZE2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
CV_SIZE1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
CV_SIZE0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
Paper size none A3 A4 LT B4 LG WLT INV B5 Extra A5 F4 A4R B5R LTR A5R
Memo
manuals4you.com
Memo
LEAD-FREE SOLDER
The PWBs of this model employs lead-free solder. The LF marks indicated on the PWBs and the Service Manual mean Lead-Free solder. The alphabet following the LF mark shows the kind of lead-free solder.
Example:
<Solder composition code of lead-free solder> Solder composition code (Refer to the table at the right.) Solder composition Sn-Ag-Cu Sn-Ag-Bi Sn-Ag-Bi-Cu Sn-Zn-Bi Sn-In-Ag-Bi Sn-Cu-Ni Sn-Ag-Sb Bi-Sn-Ag-P Bi-Sn-Ag Solder composition code a b z i n s p
Lead-Free
5mm
manuals4you.com
(German) Achtung Explosionsgefahr bei Verwendung inkorrekter Batterien. Als Ersatzbatterien drfen nur Batterien vom gleichen Typ oder vom Hersteller empfohlene Batterien verwendet werden. Entsorgung der gebrauchten Batterien nur nach den vom Hersteller angegebenen Anweisungen.
Trademark acknowledgements
Microsoft Windows operating system is a trademark or copyright of Microsoft Corporation in the U.S.A. and other countries. Windows 95, Windows 98, Windows Me, Windows NT 4.0, Windows 2000, and Windows XP are trademarks or copyrights of Microsoft Corporation in the U.S.A. and other countries. IBM and PC/AT are trademarks of International Business Machines Corporation. Acrobat Reader Copyright 1987- 2002 Adobe Systems Incorporated. All rights reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated. All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION Digital Document System Group Quality Enhancement Center Yamatokoriyama, Nara 639-1186, Japan
2005 February Printed in Japan
manuals4you.com
PARTS GUIDE
CODE:00ZARM351U004
Revised Edition
1 Exteriors 2 Left door unit 3 PS roller unit 4 Main drive unit 5 Transfer unit 6 Cassette paper feeder 7 Fusing unit 8 Delivery turn over unit 9 MC unit F Process unit [AR-M355N/U,AR-M455N/U,
AR-M351N/U,AR-M451N/U]
SHARP CORPORATION
This document has been published to be used for after sales service only. The contents are subject to change without notice.
DEFINITION
Rank Rank Rank Rank Rank A B E D C : : : : : Maintenance parts, and consumable parts which are not included in but closely related to maintenance parts Performance/function parts (sensors, clutches, and other electrical parts), consumable parts Unit parts including PWB Preparation parts (External fitting, packing, parts packed together) Parts other than the above (excluding sub components of PWB)
Because parts marked with "! " is indispensable for the machine safety maintenance and operation, it must be replaced with the parts specific to the product specification. F Other than this Parts Guide, please refer to documents Service Manual(including Circuit Diagram)of this model. F Please use the 13 digit code described in the right hand corner of front cover of the document, when you place an order. F For U.S. only-Use order codes provided in advertising literature. Do not order from parts department. [NOTE] * There patrs are supplied by SMF
New & Addition, Change, Abolition, and Quantity change are expressed with the marks shown in the table below. <Change of Division>
New & Addition Change Abolition Q'uantity (increase) /Others Q'uantity (decrease) Correction
manuals4you.com
1 Exteriors
NO.
1 2 3 4 5 6 7 11 13 14 15 16 17 18 19 20 21 22 23 24 25
PARTS CODE
GCAB-0938FCNZ LX-BZ0909FCZZ TLABZ4693FCZZ TLABZ4694FCZZ GCAB-0940FCN3 TLABZ0105RSZZ TLABH4438FCZZ GCAB-1079FCZZ GCAB-0934FCN2 GCAB-0935FCNZ XEBS740P10000 GCAB-1080FCZZ GCAB-0937FCNZ GCAB-0941FCZ3 GCAB-0941FCZ1 PFTA-0139FCZZ GCAB-0939FCN2 XHBS740P08000 LPLTM5937FCZZ PCOVP1554FCNZ PCOVP1618FCZZ XHBS730P06000 CBDGD0047FC04 CBDGD0047FC05 CBDGD0047FC15 CBDGD0047FC17 CBDGD0047FC09 CBDGD0047FC18 CBDGD0047FC16 CBDGD0047FC10 CBDGD0047FC22 CBDGD0047FC23 JHNDP0158FCZZ TLABS4306FCZZ TLABZ4818FCZZ TLABF2705FCZZ TLABH4186FCZZ TCAUA0770FCZZ TLABS3760FCZZ TLABH0108GCZZ TLABZ4173FCZZ LPLTM6372FCZZ PMAGT0144FCPZ XEBS740P14000 XEBS730P06000
26
27 30 31 32 33 34 35 36 37 38 39
Inter- PRICE NEW PART change RANK MARK RANK AY D Right cabinet AC C Screw AF D D mark label AF D Imager label BA D Paper exit tray cabinet AD D LAG label AD D Label Spain AQ D Front cabinet upper right AW D Front cabinet AN D Front cabinet upper AA C Screw(410) AR D Upper cabinet left AL D Left cabinet rear AX D Rear cabinet AW D Rear cabinet AD C Delivery tray cabinet cover AL D Right cabinet rear AA C Screw(48) AS C Rear cabinet support plate AF C Harness cover AG C ROM cover AC C Screw(36) AN C Badge AN C Badge AN C Badge AN C Badge AN C Badge AN C Badge AN C Badge AN C Badge AM C Badge AM C Badge AE C Handle R lower AC D Noise label class A AD D Argentina standard label FCC conformity label A,B AB D AE AB AC AC AG AC AH AB AA D D D D D C C C C Class A VCCI label Service cautions label CE mark label
DESCRIPTION
[Except U.S.A,CANADA] [U.S.A,CANADA] [Argentina] [U.Kingdom,Europe,Argentina]
TR No.
Effective time
[AR-M355N] [AR-M455N] [AR-M351N] [AR-M351U] [AR-M355U] [AR-M451U] [AR-M451N] [AR-M455U] [AR-M312U] [AR-M420U] [U.S.A,CANADA] [Argentina] [U.S.A,CANADA] [Except AR-M312U,AR-M420U] [AR-M312U,AR-M420U] [U.Kingdom,Europe,Lebanon,Iran, West Africa,Pakistan,Algeria] [Except U.S.A,CANADA] [U.kingdom,Europe]
Class 1 label EGI Connection apparatus caution label Front cabinet catch plate Front cabinet magnet Screw(414) Screw(36)
1-1
1 Exteriors
34
25
25
24 27 21
21
23 21
32
22 31 15 7 21 15
21
35 30 33 6 5 19 18 2 20
2 1 21
21
21
17
15
21
15 16 15 15 11 21 14 36 39 37 13 4 FCP09281 3 26 38 15
manuals4you.com
1-2
PARTS CODE
PGIDM2077FCZ1 XRESP40-06000 LX-BZ0147FCZ1 PGIDM1885FCZZ PGIDM1884FCZZ MSPRC2953FCZZ LSTYM0258FCZZ LSTYM0259FCZZ PTME-0287FCZ1 LHLDZ1439FCZZ MSPRC2835FCZZ LANGT1407FCZ2 XEBS740P12000 MLEVP0781FCNZ PTME-0279FCZ1 LSTYM0256FCZZ GDOR-0030FCN1 PCOVP1531FCNZ CPWBF1599FCE1 DHAI-3235FCZZ QEARP0136FCZZ CPWBF1593FCE2 PCOVP1567FCNZ NFANP0069FCZZ LX-WZ0028FCZZ XEBS730P10000 LPINS0320FCZZ NSFTZ2572FCZZ LANGT1409FCZ1 LSTYM0257FCZ1 MSPRD2838FCZZ XEBS740P10000 XRESP50-06000 LANGT1408FCZ1 XHBS740P06000 XEBS730P14000 XEBS740P08000 PMLT-1263FCZZ PMLT-1266FCZZ PMLT-1265FCZZ PMLT-1264FCZZ LX-BZ0465FCWZ MSPRT2836FCZZ PFILZ0287FCZZ (Unit) CDOR-0030DS52
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AL D Reverse gate AA C E type ring(E4) AC C Screw AR D Left door exit paper reverse guide AU D Left door transfer PG AB C Reverse PG support spring AG C Left door support plate upper AD C Left door support plate lower AD C Transfer lock pawl AC C Transfer unit pressure holder AC C TR pressure spring AR C ACC fixing angle F AA C Screw(412) AD C Left door release lever AB C Left door lock pawl AN C Rail support plate F BC D Left door AK C Left door cover lower AF E Drawer PWB AE C Left door interface harness AD C Left door transfer earth plate AK E High voltage resistor PWB AC C Left door upper cover AV B Fan AA C Washer AC C Screw(310) AB C Spring pin(2-8) AH C Lock lever joint shaft AH C ACC fixing angle R lower AL C Rail support plate R AC C Left door lock spring AA C Screw(410) AA C E type ring(E5) AG C ACC fixing angle R upper AA C Screw(46) AD C Screw(314) AA C Screw(48) AD C Suction cushion A AD C Suction cushion D AD C Suction cushion C AD C Suction cushion B AA C Screw(46) AC C Reverse gate spring AU A Ozone filter BP E Left door unit
TR No.
Effective time
2-1
2 46 37 38 41 38 41 35 6 35 6 6 36 33 41 46 38 41 32 41 41 38 26 26 38 41 16 34 30 31 8 7 35 4 14 14 5 41 30 42 43 44 45 a 27 29 28 12 11 14 11 50 40 2122 a 41 13 36 16 15 46 12 14 14 14 9 14 29 48 3 3 1
38
29 24
23
18
20
19 FCP09282
manuals4you.com
2-2
3 PS roller unit
NO.
1 2 3 4 5 6 7 8 9 10 13 14 15 17 18 19 20 23 24 25 26 28 29 30 31 32 34 36 37 38 39 40 41 42 43 901
PARTS CODE
NROLP1512FCZZ MSPRT2839FCZZ NBRGC0286FCZZ NGERH1611FCZZ NGERH1474FCZZ LPINS0155FCZZ XRESP70-08000 NROLR1303FCZ1 PGIDH1960FCZZ XEBS730P08000 PCLR-0460FCZZ MSPRC3343FCZZ NSFTZ2573FCZ1 CPWBF1593FCE1 MSPRP1550FCZZ DHAI-3145FCZZ VHPGP2A200L-1 NBRGP0666FCZZ JKNBZ0139FCZ2 MSPRC2841FCZ2 LPINS0325FCZZ PGIDM1887FCZ1 PCLR-0461FCZZ NROLR1507FCZZ LSTYM0260FCZZ PGIDM1888FCZZ PSHEP4825FCZZ QEARP0181FCZZ NCPL-0059FCZZ LX-BZ0589FCP1 LX-WZ0070FCZZ CGIDH1961FC01 XHBS730P06000 TLABZ4731FCZZ XEBS740P12000 (Unit) CGIDM1887DS52
manuals4you.com
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AX C PS follower roller AF C PS pressure spring AC C PS follower roller bearing AC C PS follower gear AC C PS gear AA C Pin(3-10) AA C E type ring(E7) AY B PS roller AK C Paper powder remove guide AC C Screw(38) AC C Transfer follwer collar AC C PS front pressure spring AG C PS follower roller shaft AK E High voltage resister PWB PS AA C TC spring AE C PPD harness AR B LED(GP2A200L) AC C Bearing AD C PS knob AC C PS brake spring AB C Spring pin AQ D PS paper guide A AC C U-turn collar AZ B PS front roller AK C Support stay AL D PS paper guide B AD C PS roller front sheet AD C PS earth plate AC C PS coupling AA C Screw AA C Washer AQ C Drum front PG AC C Screw(36) AF D Arrow label A AA C Screw(412) BH E PS roller guide unit(Without No.42,43)
TR No.
Effective time
[U.Kingdom,Europe]
3-1
3 PS roller unit
10 41 40
2 3 4 1 6 7
8 10 17 38 37 23 9 13 18 37 23 36 19 20 10 18 10 10 34 23 29 28 43 39 24 25 26 10 10 42 30 32 31 23 7 15 14 13 14 10 10 10
10
FCP09283
manuals4you.com
3-2
PARTS CODE
NSFTZ2584FCZZ XRESP50-06000 MSPRC2616FCZZ NCPL-0046FCZZ LX-BZ0845FCZZ NBRGC0387FCZ1 XHBS730P06000 LPLTM5712FCZZ LPINS0337FCZZ NGERH1240FCZZ LPLTM5713FCZZ XHBS730P08000 DHAI-3635FCPZ NGERH1363FCZZ NBRGC0190FCZ1 NCPL-0054FCZZ NCPL-0048FCZZ NBRGY0627FCZZ XBPSD30P08K00 MSPRP1293FCZZ LX-BZ0670FCP1 QCNCM0999FCZZ QCNCM1000FCZZ XEBS740P10000 LPLTM5714FCZZ LFRM-1016FCZZ QEARP0116FCZZ MSPRP2823FCZZ DHAI-3427FCZZ PCOVP1611FCZZ CPLTM5711FC01 QEARP0117FCZZ NSFTZ2585FCZZ NGERH1416FCZZ NSFTZ2580FCZZ NGERH1413FCZZ NGERH1415FCZZ NGERH1429FCZZ NSFTZ2579FCZZ PCOVP1534FCZZ QEARP0118FCZZ QEARP0115FCZZ LPLTM5762FCZZ PSHEP4826FCZZ NPLYZ0419FCZZ NSFTZ2581FCZZ NGERH0349FCZZ NSFTZ2883FCZZ NGERH0457FCZZ NSFTZ2577FCZZ NGERH1528FCZZ NGERH1357FCZZ PCLC-0298FCZZ PCLC-0297FCZZ NGERH1414FCZZ NSFTZ2583FCZZ NSFTZ2575FCZ1 PCLC-0296FCZ1 NGERH1359FCZZ LX-BZ0788FCZ1 XRESP70-08000 XRESP60-07000 LX-BZ0576FCZZ NSFTZ2576FCZ2 XRESP40-05000 NBRGC0641FCZZ LPINS0330FCZZ LPINS0155FCZZ XNES730-18000 XBPS730P06K00 XEBS740P10000 XRESP40-05000 LPINS0133FCZZ LHLDW1006FCZZ NBRGY0773FCZZ NSFTZ2578FCZZ LX-BZ0033GCZZ PSHEP4947FCZZ PSHEP4948FCZZ PSPAZ1430FCZZ
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AG C DV joint shaft AA C E type ring(E5) AC C DV drive spring AC C DV coupling AC C Screw AC C Bearing AC C Screw(36) AE C DV drive plate AB C Pin(3-12) AD C DV drive gear(14T) AC C DV joint plate AB C Screw(38) AY C DV interface harness AC C Cleaner TB gear(19T) AD C F6 bearing AE C Cleaner coupling AK C Drum coupling AK C Bearing AA C Screw(38K) AB C Electrode spring AC C Drive joint stop screw AC C Connector(BU02P-TR-P-H)(2pin) AC C Connector(BU03P-TR-P-H)(3pin) AA C Screw(410) AB C M3 plate BA D Transfer drive frame lower AC C Left cabinet earth spring AD C TB spring AN C HV harness AC C Transfer high voltage cover AH C DV gear fixing plate AC C Drum earth joint spring AG C Cleaner TB shaft AE C Cleaner gear AK C Drum turn shaft AM C Drum gear AN C DR idle gear AE C DV drive gear AE C Drum motor shaft AX D Transfer drive cover AC C Transfer earth joint spring AF C Drum earth plate AC C Rear cabinet fixing plate B AC C Pulley sheet AD C Elevator drive pulley(22PS3M) AE C Fusing drive shaft AC C Gear(CL28T) AP C Main drive joint shaft AC C DV drive gear R AL C Main motor shaft AE C PS drive gear AD C Gear(48/28T) AT B Paper feed clutch AU B PS front clutch AC C Paper feed joint gear AF C Paper feed shaft AF C PS front roller shaft AX B PS clutch AD C Gear(15/24T) AC C Screw AA C E type ring(E7) AA C E type ring(E6) AC C Screw(46) AF C PS roller shaft AA C E type ring(E4) AD C Bearing AB C Spring pin(3-16) AA C Pin(3-10) AA C Nut AA C Screw(36K) AA C Screw(410) AA C E type ring(E4) AA C Pin(210) AA C Mini clamp(UAMS-09-0) AP C Bearing AN C DV joint shaft AC C Screw AC C PS front clutch sheet AC C PF clutch sheet AB C Spacer(8-8)
TR No.
Effective time
4-1
PARTS CODE
LX-WZ0070FCZZ LX-WZ0017FCPZ MSPRC3027FCZ1 LX-WZ0421FCZZ LX-WZ0198FCZZ (Unit) CFRM-1016DS53
Inter- PRICE NEW PART change RANK MARK RANK AA C Washer AA C Adjust Washer AD C PS front spring AA C Washer AA C Washer BR E
DESCRIPTION
TR No.
Effective time
6 9 11 12
3 2 3 8 3
10 14
13
32 33 76 34 77 34 35 78 36 68 37 78 38 66 67 78 70 78 64 92 73 60 85 68 44 91 43 73 81 8 78 47 78 78 49 29 50 68 78 42 41 68 11 40 17 79 80 39 79
89
34 30
22 83
54
46 11 51 78
78
manuals4you.com
5 Transfer unit
NO.
1 2 3 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 901
PARTS CODE
LHLDZ1482FCZ3 LPLTM5875FCZ1 PGIDM1950FCZ2 LPLTM5925FCZZ XEBS740P08000 MSPRC3000FCZZ NROLR1355FCP1 NBRGP0655FCZZ PCLR-0468FCZ1 MSPRC2955FCZZ LHLDZ1474FCZ2 LPLTM5926FCZ1 PTME-0288FCZZ NGERH1419FCZZ QEARP0132FCZZ XBPS730P06KS0 NBRGP0656FCZZ PRNGF0107FCZZ MSPRC3342FCZZ (Unit) CHLDZ1474DS52
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AF C Discharge plate holder AK B Discharge plate AE D Transfer front PG AQ C Transfer front PG plate AA C Screw(48) AC C Transfer front PG spring AZ B Transfer roller AD C TR bearing F AC C Transfer roller collar AB C Reverse pressure spring AL D TR holder AS C Holder support plate AC C Transfer lock pawl AK C TR gear AE C TR earth plate AB C Screw(36KS) AD C TR bearing R AC C Starling AC C Transfer R pressure spring BF E Transfer unit
TR No.
Effective time
5 Transfer unit
17 19 19 19
19 6 2 19 19 16 20 1 18 10 15 7 3
6 6 8 5
14 6 13 6 6 11 12 6
5-1
9 10
FCP09285
Update : 06/02/27
PARTS CODE
LDAIU0622FCZZ LDAIU0622FCZ1 XEBS740P10000 PCOVP1543FCZ1 DHAI-3155FCZZ MLEVP0785FCZZ VHPGP1A73A+-1 PGIDM1891FCZZ NSFTZ2591FCZZ NPLYZ0365FCZZ NROLR1509FCZZ NBLTH0432FCZZ NROLR1508FCZZ PCLC-0348FCZZ NCPL-0049FCZZ NSFTZ2590FCZ1 NPLYZ0373FCZZ XRESP50-06000 LX-BZ0960FCZZ PCLR-0441FCZZ PCLR-0519FCZZ LRALP0185FCZ1 PGIDM1893FCZZ PGIDM1892FCZZ PRNGP0090FCZZ XPSSJ20-08000 LPINS0329FCZZ NSFTZ2589FCZZ NBRGC0387FCZ1 MSPRC3012FCZZ NCPL-0047FCZZ LX-BZ0916FCPZ MARMP0259FCZZ MSPRD2850FCZZ CPLTM5732FC01 XHBS740P08000 MSPRT3341FCZZ PSPAZ1429FCZZ
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AY C Paper feed base plate 5 AU C Paper feed base plate [Unleaded correspondence][With No.14-57] AA C Screw(410) AF C Paper feed upper cover AK C Cassette detect interface harness AE C PE actuator AG B Photo sensor(GP1A73A) AG C Pick-up roller guide AF C Pick-up roller shaft AC C Pick-up roller pulley AX B Pick-up roller AF B Belt(55MXL3.2) AX B Paper feed separation roller AP C Separete torque limiter AH C Oneway coupling AH C Separation roller shaft AH C Paper feed roller pulley AA C E type ring(E5) AC C Screw(16) AK C Collar(16) 1 AE C Collar(16) AQ D Left rail AH C Paper feed PG AE C Separation roller guide AA C Ring(E5) AA C Spring pin(2-8) AB C Spring pin(2-16) AL C Paper feed roller shaft AC C Bearing AC C Paper feed brake spring AC C Paper feed coupling AA C Screw AC C Pick-up roller arm AE C Pick-up roller arm spring AF C Pick-up roller arm fixing plate AA C Screw(48) AC C Separete pressure spring AB C Spacer
TR No.
06/05
manuals4you.com
6-1
Update : 06/02/27
36
35 37 34 17
a
6
b
2 7 5 4
32 31 30 39 29
a
3
b
24
17
27
28 8 23 17 17 26 9 29 17 16 15 22 11 14 13 12 12 10
38
21 19 20 FCP09286
6-2
7 Fusing unit
NO.
1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 19 20 ! ! ! ! 21 22 23 24 25 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57
PARTS CODE
PGIDM1895FCZZ LX-BZ3008SCPS PTME-0300FCZZ MSPRT2852FCZZ XHBS740P08000 RDTCT0164FCZZ RDTCT0147FCZZ LX-BZ0905FCPZ DHAI-3156FCZZ XBPS730P08KS0 PCOVP1546FCZ1 LPLTM5737FCZZ LX-NZ0094FCZZ LPLTM5739FCZZ RTHM-0024FCZZ QEARP0123FCZZ LPLTM5738FCZZ LSTYM0268FCZZ LFIX-0442FCZZ LSTYM0267FCZZ RLMPU0662FCZZ RLMPU0664FCZZ NROLI1314FCZ1 RLMPU0661FCZZ RLMPU0663FCZZ NBRGY0773FCZZ PGIDM1894FCZZ CSTYM0265FC02 MLEVP0790FCZ2 XEPS840P08X00 MLEVP0786FCZZ LX-BZ0906FCZZ CFLT-0064FC06 PCOVP1547FCZZ MLEVF0788FCZ3 XRESP50-06000 MSPRC3327FCZZ CSTYM0266FC02 MLEVF0789FCZ3 MLEVP0791FCZ2 MLEVP0787FCZZ PTME-0283FCZZ MSPRD2853FCZZ PGIDM1951FCZ1 LSTPF0172FCZZ NBRGY0646FCZZ NROLT1549FCZZ NROLT1313FCZZ NGERH1380FCZZ TLABZ4205FCZZ XHPS730P06000 LFIX-0441FCZZ MSPRT2957FCZZ NROLM1560FCZZ NROLM1387FCZZ NBRGP0670FCZZ MSPRT3028FCZZ LX-BZ0997FCZZ LSTPP0381FCZZ LRTNP0012FCPZ (Unit) DUNTW7095DS15 DUNTW7095DS11 DUNTW7095DS16 DUNTW7095DS12
Inter- PRICE NEW PART change RANK MARK RANK AN D Fusing rear upper PG AA C Screw(38) AK C Upper separator pawl AB C Top pawl spring AA C Screw(48) AR B Thermistor AR B Thermistor AB C Screw(312KS) AT C Fusing harness AB C Screw(38KS) AY D Fusing upper cover AD C Lamp fixing plate F AC C Nut(M3) AD C Thermostat fixing plate AM B Thermostat AE C Electrode plate AD C Lamp fixing plate R AE C HR support plate R AB C Fusing shaft fixing plate R AE C HR support plate F AX B Heater lamp sub 120 AY B Heater lamp sub 240 BH B Pressure roller AX B Heater lamp main 120 AY B Heater lamp main 240 AP C Bearing AP C Fusing front lower PG AF C Pressure support plate F AE C Fusing lever F AC C Screw(48X) AC C Pressure adjust lever F AC C Screw(M4) AN C Fusing cushion AY D Fusing lower cover AF C Pressure lever F AA C E type ring(E5) AC C Fusing pressure spring AF C Pressure support plate R AF C Pressure lever R AE C Fusing lever R AC C Pressure adjust lever R AL C Lower separator pawl AB C Lower pawl spring AQ D Fusing rear lower PG AA C Roller stopper AS C Bearing BE A Heat roller upper BE A Heat roller upper AQ B Fusing gear(48T) AC D Green label AA C Screw(36) AB C Fusing shaft fixing plate F AC C PG open close spring BA B CL roller AL B CL roller AD C CL roller bearing AD C CL roller spring AB C Screw AE C Stopper R AD C Retainer BZ CB BZ CB E E E E Fusing Fusing Fusing Fusing unit(Without unit(Without unit(Without unit(Without No.56) No.56) No.56) No.56)
DESCRIPTION
TR No.
Effective time
901
[120V series][Except AR-M312U,AR-M420U] [120V series][AR-M312U,AR-M420U] [200V series][Except AR-M312U,AR-M420U] [200V series][AR-M312U,AR-M420U]
manuals4you.com
7-1
7 Fusing unit
1 3 3 4 4 3 5 4 17 3 4 6 18 16 15 44 47 45 12 49 19 46 48 43 45 24 23 56 39 29 5 40 42 41 42 41 37 38 52 55 24 53 36 5 54 35 36 35 54 5 30 32 5 31 28 29 FCP09287
7-2
6 5 5 7
14 14 13
5 11
50 49
10 10
7 57 8
20 55 21 44
53 51
22
31 34 2 27
25
33
PARTS CODE
PMLT-1408FCZZ LPLTM5921FCZ1 XEBS740P10000 XHBS740P08000 NFANP0075FCZZ MLEVP0828FCZZ MLEVP0838FCZZ MLEVP0792FCZ1 VHPGP1SQ73P-1 VHPGP1A73A+-1 PGIDM1896FCZ1 PGIDM1896FCZ2 PGIDM1896FCZ4 PGIDM1896FCZ4 NROLP1296FCZZ NSFTZ2593FCZZ LDAIU0626FCZ2 NROLR1315FCZ2 NGERH1384FCZZ NBRGC0387FCZ1 NBRGC0504FCZZ XRESP70-08000 NROLR1316FCZ3 LFRM-1020FCZ1 MLEVP0793FCZZ PCLR-0462FCZZ NGERH1398FCZZ NGERH1383FCZZ LPINS0265FCZZ CPLTM5740FC01 MSPRT2858FCZZ MSPRC2857FCZZ NSFTZ2594FCZZ NROLP1473FCZZ NSFTZ2595FCZZ JKNBZ0140FCZZ NGERH1593FCZZ NSFTZ2598FCZ1 NGERH1421FCZ1 NBLTH0327FCZ1 NPLYZ0385FCZZ NBRGY0131FCZZ NSFTZ2597FCZZ NGERH0111FCWZ NGERH1447FCZ1 NSFTZ2596FCZZ NBLTH0350FCZ1 DHAI-3640FCZZ DHAI-3158FCZZ MSPRD2859FCZ1 LX-BZ0937FCZZ QSW-M0502FCPZ XEBS730P16000 LFRM-1021FCZ1 QEARP0124FCZZ DHAI-3157FCZZ RMOTS0859FCZZ PSHEZ4914FCZZ PMLT-1276FCZZ PSHEP4943FCZZ MSPRD2855FCZZ PBRSS0208FCZ1 MSPRD2856FCZZ XHBS730P06000 DHAI-3673FCZZ DHAI-3333FCZZ PSHEP4962FCZ1 PDUC-0181FCZZ TLABZ4732FCZZ XEBS740P12000 (Unit) CFRM-1020DS52 CFRM-1020DS53
10
11 12 14 15 16 17 18 19 20 21 22 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 40 41 42 43 44 45 47 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AC C Exhaust cushion AQ C Paper exit upper PG support plate AA C Screw(410) AA C Screw(48) BA B Fan AD C Paper exit actuator AC C Detect lever AD C Paper exit actuator AF B Photo sensor(GP1SQ73P) [Except AR-M312U,AR-M420U] AG B Photo sensor(GP1A73A) [AR-M312U,AR-M420U] AV D Paper exit upper PG [AR-M355U/N,AR-M455U/N] Paper exit upper PG [Incorrect insertion prevention] 6 AS D [AR-M355U/N,AR-M455U/N] 3 AS D Paper exit upper PG [Form change][AR-M355U/N,AR-M455U/N] AS D Paper exit upper PG [AR-M351U/N,AR-M451U/N,AR-M312U,AR-M420U] AC C Paper exit follower roller AF C Paper exit follower roller shaft AK C Paper exit follower roller fixing plate AM B Exit paper roller AC C Paper exit gear(30T) AC C Bearing AC C PF bearing(F8125 16X) AA C E type ring(E7) AS B Fusing roller rear AZ D Paper exit frame AE C Fusing rear actuator AE C Collar AL C Gear(24T) AD C Fusing drive gear(30T) AB C Spring pin(M312) AE C Fusing joint plate AC C Fusing joint spring AA C Paper exit follower roller spring AP C Fusing rear follower shaft AF C Fusing rear follower roller AN C Fusing knob shaft AF C Fusing knob AQ C Fusing drive gear(30T) AG C Fusing drive joint shaft AH C Oneway gear(30T) AL B Belt AD C Pulley(S3M-35T) AM C Bearing AE C Fuing drive idle shaft AD C Idle gear(24T) AH C Oneway gear(24T) AG C Ratchet shaft AH B Belt AX C Paper exit unit harness [Except AR-M312U,AR-M420U] AQ C Paper exit unit harness [AR-M312U,AR-M420U] AE C Door switch spring AB C Screw(312) AH B Door switch(AM51632C531N) AA C Screw(316) AL C Paper exit drive frame AK C Paper exit earth plate AE C Sensor harness BC B Paper exit motor AB C Paper exit soundproof sheet AA C Paper exit cushion AB C Reverse gate sheet AB C Paper exit actuator spring AH B Discharge brush AB C Fusing actuator spring AC C Screw(36) AE C Paper exit earth harness [Except AR-M312U,AR-M420U] AE C Paper exit earth harness [AR-M312U,AR-M420U] AC C Belt fixing sheet AL D Exhaust duct AF D Arrow label B (U.Kingdom,Europe) AA C Screw(412) BU BU E E Delivery turn over unit(Without No.38,65,68,69) Delivery turn over unit(Without No.38,65,68,69) [Except AR-M312U, AR-M420U] [AR-M312U,AR-M420U]
TR No.
Effective time
901
manuals4you.com
8-1
3 2 9 61 3 3 3
62
65 64 57 b 56 55 3 a 59 3 53 54 18 19 52 40 27 47 19 19 40 27 66 44 19 38 41 19 37 36 34 33 30 31 32 31 32 19 30 29 18 28 35 19 24 FCP09288
8-2
6 58 58 8 7 5 10 60 11 11 17 18 12 16 27 30 3 30 12 3 30 18 19 20 15 14 19 18 3
50 26 49 45 19
51
19 27
43 42 19
18 18 68 b 58 9 18 27 25 21 22 69 69 63
9 MC unit
NO.
1 2 3 5 6 7 8 9 10 11 12 901
PARTS CODE
XEBS730P08000 PCASZ0295FCZZ CPLTM6048DS53 CPLTM6048DS51 LHLDZ1621FCZZ LHLDZ1470FCZZ LX-BZ0859FCZZ QSLP-0194FCZZ QSLP-0195FCZZ LPLTM5873FCZZ LHLDZ1471FCZZ CHLDZ1623DS51 PSHEP4911FCZZ (Unit) CCASZ0295DS52 CCASZ0295DS51
Inter- PRICE NEW PART change RANK MARK RANK AC C Screw(38) AP D MC case AM E Plate AL E Plate AD C MC holder A AD C MC holder A AC C Screw AC C Terminal AD C Grid terminal AG B Grid AC C MC holder B AZ E Cleaner holder unit AB C MC sheet BC BA E E MC unit MC unit
DESCRIPTION
[Except AR-M312U,AR-M420U] [AR-M312U,AR-M420U] [Except AR-M312U,AR-M420U] [AR-M312U,AR-M420U]
TR No.
Effective time
9 MC unit
11
6 7
2 3
8 1 12 9 1
10
FCP09289
manuals4you.com
9-1
F Process unit[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 17 18 20 21 24 26 27 28 29 30 32 33 34 35 36 37 38 39 40 41 42 44 45 46 47 48 49 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 501 901
PARTS CODE
MLEVP0832FCZZ XRESP30-06000 NGERH1417FCZZ LRALM0180FCZ5 LRALM0180FCZ4 NGERH1612FCZZ XHBS730P08000 LPLTM5714FCZZ PMLT-1245FCZ2 PCOVP1804FCZZ XEBS730P08000 XRESP40-06000 NBRGP0642FCZZ NSRW-0033FCZ1 PPIPP0206FCZZ MSPRC3010FCZ1 PSHT-0088FCZZ NGERH1369FCZZ NBRGP0771FCPZ NGERH0039QSZZ XBBS730P08000 LX-BZ0656FCZ1 PCOVP1803FCZ1 XRESP50-06000 NGERH0038QSZZ NGERH0037QSZZ QEARP0182FCZ1 PSHEZ4827FCZZ NSRW-0032FCZZ LPFTF0121FCZZ LPFTF0108FCZZ PSHEZ5335FCZZ NROLP1504FCZZ PMLT-1390FCZZ XEPSD40P12000 NCPL-0073FCZZ CCLEZ0163FC32 PTME-0286FCZ1 PRNGF0106FCZ2 LHLDZ1473FCZZ MSPRC2954FCZ2 PMLT-1238FCZ1 CCLEZ0162FC31 XBBS230P06000 CFRM-1017FC02 MSPRC2961FCZZ NBRGP0654FCZZ PSEL-0805FCZZ QEARP0133FCZZ LX-WZ0440FCZZ PSPAZ1431FCZZ MJNTM0027FCZZ MJNTM0028FCZZ JHNDP0167FCZ1 LPLTM6447FCZZ NSFTZ2884FCZZ PSPAP1445FCZZ XEPS740P10000 CPLTM6448FC01 CHLDZ1473DS55 (Unit) CFRM-1017DS87 CFRM-1017DS86
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AF C Lever AA C E type ring(E3) AC C Paddle gear(14T) AM C TH rail B [U.kingdom,Europe,Australia,New Zealand] AM C TH rail A [U.S.A,Other Countries] AD C Paddle idle gear(14T) AB C Screw(38) AB C M3 plate AE C Process U cushion AG D Process cover U AC C Screw(38) AA C E type ring(E4) AE C Waste toner bearing AC C 2nd Transfer screw AD C Waste toner transfer pipe AB C Shutter open/close spring AC C Pipe shutter AC C Toner transfer gear(30T) AC C Bearing MX AE C Transport pipe gear(14T) AA C Screw(38) AE C Screw AG C Process cover AA C E type ring(E5) AC C Transport pipe gear(15T) AC C Idle gear(26T) AD C Process earth plate AD C Sheet F AG C Transfer screw AE C DSD flange F AK C DSD flange R AC C Sheet R AG C Transfer paddle AC C Handle cushion AA C Screw(412) AD C Waste toner screw coupling AS B Sub blade AH C Separator pawl AC C Starling N AC C Separation pawl holder AB C Separation pawl spring AC C Toner shield cushion AW B Cleaning blade AD C Screw(36) AW D Process frame AB C Lever spring AC C Transfer bearing F AE C G seal AC C Process earth plate B AC C Spacer AA C Spacer A AC C Cleaner joint A AC C Cleaner joint B AC C MC cleaner handle AE C Frame reinforce plate BH C Cleaner shaft AC C Reinforce plate spacer AB C Screw(410) AG C Drum boss fixing plate AK E Separation pawl holder unit BN BN E E Process unit(include 9-901) Process unit(include 9-901) [U.Kingdom,Europe,Australia,New Zealand] [U.S.A,Other Countries]
TR No.
Effective time
10-1
F Process unit[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
53 41 12 1 6 42 10 38 2 5 3 12 7 7
10 56 10 60 59 9 10 7 7 8 7 10 46 37 63
901
4
47 45 46
501
46 47 45 46 47 45
11 12 13 29 6 10 14 16 30 20 18 20 21 62 40 64 40 24 61 40 26 39 17 27 24
47 45 44 10
501
44
10
44 10
501
51
52 48
501
44 10
51 36 51
7 33
2 55 32 54 58
57
28
49
34
FCP09290 35
66
65
manuals4you.com
10-2
G Process unit[AR-M312U,AR-M420U]
NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 17 18 20 21 22 24 26 28 29 30 32 33 34 35 36 37 38 40 41 42 44 45 46 47 48 49 51 52 53 54 55 56 57 58 59 62 64 501
PARTS CODE
MLEVP0832FCZZ XRESP30-06000 NGERH1417FCZZ LRALM0180FCZ7 NGERH1612FCZZ XHBS730P08000 LPLTM5714FCZZ PMLT-1245FCZ2 PCOVP1589FCZ1 XEBS730P08000 XRESP40-06000 NBRGP0642FCZZ NSRW-0033FCZ1 PPIPP0206FCZZ MSPRC3010FCZ1 PSHT-0088FCZZ NGERH1369FCZZ NBRGP0771FCPZ NGERH0039QSZZ MLEVP0782FCBZ XBBS730P08000 LX-BZ0656FCP1 XRESP50-06000 NGERH0038QSZZ NGERH0037QSZZ QEARP0131FCZZ PSHEZ4827FCZZ NSRW-0032FCZZ LPFTF0107FCZZ LPFTF0108FCZZ PSHEZ4828FCZ1 NROLP1504FCZZ XEPS740P12000 NCPL-0073FCZZ CCLEZ0163FC32 PTME-0286FCZ1 PRNGF0106FCZ2 LHLDZ1473FCZZ MSPRC2954FCZ2 PMLT-1238FCZ1 CCLEZ0162FC31 LX-BZ0047QSZZ CFRM-1017FC02 MSPRC2961FCZZ NBRGP0654FCZZ PSEL-0805FCZZ QEARP0133FCZZ LX-WZ0440FCZZ PSPAZ1431FCZZ PSPAZ1432FCZZ LPLTM6447FCZZ PSPAP1445FCZZ CHLDZ1473DS55
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AF C Lever AA C E type ring(E3) AC C Paddle gear(14T) AM C TH rail A AD C Paddle idle gear(14T) AB C Screw(38) AB C M3 plate AE C Process U cushion AG C Process cover U AC C Screw(38) AA C E type ring(E4) AE C Waste toner bearing AC C 2nd Transfer screw AD C Waste toner transefer pipe AB C Shutter open close spring AC C Pipe shutter AC C Toner transfer gear(30T) AC C Bearing MX AE C Transport pipe gear(14T) AC C Process lever BK AA C Screw(38) AD C Screw AA C E type ring(E5) AC C Transport pipe gear(15T) AC C Idle gear(26T) AD C Process earth plate AD C Sheet F AG C Transfer screw AK C DSD flange F AK C DSD flange R AD C Sheet R AG C Transfer paddle AB C Screw(412) AD C Waste toner screw coupling AS A Sub blead AH C Separator pawl AC C Starling N AC C Separation pawl holder AB C Separation pawl spring AC C Toner shield cushion AW A Cleaning blead AB C Screw(36) AW C Process frame AB C Lever spring AC C Transfer bearing F AE C G seal AC C Process earth plate B AC C Spacer AA C Spacer A AA C Spacer B AE C Frame reinforce plate AC C Reinforce plate spacer AK E Separation pawl holder unit
TR No.
Effective time
11-1
G Process unit[AR-M312U,AR-M420U]
53 1 41 12 2 6 7
10 56 59
10 4 9
42 10 47 47 45 44 46 46 45 47 4546 44 47 10
10 12 7 7 7 8 37 7 13 52 12 11
38 5
501
44
501
501
45 44
46 10 51 49
48 29 54 51 7 33 36 51 32 58 2 64 34 40 6 10
14
501
55 30 20 21 22
16 20 18 28 24 17
57
26 24 24
FCP09291
62
40
35
51
manuals4you.com
11-2
H DV unit[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 21 22 25 26 27 28 29 35 36 37 38 39 40 41 42 43 44 46 47 48 49 50 53 54 55 56 57 58 901
PARTS CODE
DHAI-3636FCZZ XBBS730P08000 PCOVP1538FCZZ XEBS730P08000 CPLTM5716FC01 CGERH1420FC01 XRESP40-06000 NGERH1371FCZZ XRESP50-06000 CHLDZ1445FC02 NGERH1374FCZZ NGERH1373FCZZ CBRGP0639FC01 XBPSD30P25K00 NROLM1502FCZZ LPLTM6449FCZZ NROLP1505FCZZ JHNDP0166FCBZ PCOVP1806FCZ1 LDAIU0693FCZZ RDTCH0161FCZZ MLEVP0783FCZZ MSPRC2875FCZZ JHNDP0153FCZ5 XBBS740P08000 LPLTM6022FCZZ LPLTM5715FCZZ CHLDZ1444FC02 PBOX-0125FCZ1 PSEL-0797FCZZ RDTCT0162FCZZ XEBS730P06000 MSPRD2876FCZZ MARMP0258FCZZ PSEL-0798FCZZ PCOVP1590FCZZ PMLT-1391FCZZ PSEL-0800FCZ1 PMLT-1241FCZ1 PMLT-1244FCZ1 PTPE-0281FCZZ PCAPH0004YSZZ XWHSD30-05070 UCLEZ0164FCZZ PMLT-1296FCZZ PSHEP5390FCZZ PSPAP1447FCZZ (Unit) CBOX-0125DS58
Inter- PRICE NEW PART change RANK MARK RANK AW C DV harness AA C Screw(38) AF C DV R cover AC C Screw(38) AF C Idle gear fixing plate AF C Idle gear(29T) AA C E type ring(E4) AC C MG gear(22T) AA C E type ring(E5) AK C MG holder R AC C MX gear B(31T) AD C MX gear A(34T) AH C MX bearing AA C Screw(325K) BH B MG roller AT B DV doctor N AP C MX roller A AC C SRU handle AG D DV cover AC C Doctor side block AX B Humidity sensor AD C DV lock lever AC C F handle spring AE D DV F handle AA C Screw(48) AC C M4 plate AC C PP plate AG C MG holder F AS D DV BOX AC A DV side seal F AZ B ATC sensor AA C Screw(36) AC C DV spring AD C DV joint arm AC A DV side seal R AE C Bottom cover AF C Cushion AC C DV seal 2 AA C DV-BOX cushion AC C Doctor cushion R AA C Doctor suede AC C Cap D AA C Washer AG B DV blead AH C Shutter cushion AD C DV sheet AC C DV spacer BS E DV unit
DESCRIPTION
TR No.
Effective time
12-1
H DV unit[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
28 2 1 21 50 4 5 6 7 8 9 10 29 3 7 12 7 13 14 7 11 7 13 57 54 15 47 50 21 56 43 37 41 22 42 40 44 39 40 38 36 48 35 58
a b
46
20
16
49 17
19
28
55
b a
25
26 27
29 54 14 13 29 9 4 13 7 53 28
48
FCP09292
manuals4you.com
12-2
I DV unit[AR-M312U,AR-M420U]
NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 23 24 25 26 27 28 29 32 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 901
PARTS CODE
DHAI-3148FCZZ XBBS730P08000 PCOVP1538FCZZ XEBS730P08000 CPLTM5716FC01 CGERH1420FC01 XRESP40-06000 NGERH1371FCZZ XRESP50-06000 CHLDZ1445FC01 NGERH1374FCZZ NGERH1373FCZZ CBRGP0639FC01 XBPS730P16K00 NROLM1502FCZZ LPLTM5876FCZZ NROLP1294FCZZ NROLP1295FCZZ JHNDP0166FCBZ PCOVP1592FCZZ CSHT-0089DS51 PCOVP1591FCZZ MSPRD2956FCZZ MLEVP0783FCZZ MSPRC2875FCZZ JHNDP0153FCZZ XBBS740P08000 LPLTM6022FCZZ CPWBF1591FCE1 LPLTM5715FCZZ CHLDZ1444FC01 PBOX-0125FCZ1 PSEL-0797FCZZ RDTCT0146FCZZ XEBS730P06000 MSPRD2876FCZZ MARMP0258FCZZ PSEL-0798FCZZ PCOVP1590FCZZ PMLT-1260FCZZ PMLT-1242FCZZ PSEL-0800FCZ1 PMLT-1241FCZ1 PMLT-1244FCZ1 PSHEZ4882FCZ1 PSHEZ4883FCZZ PSHEZ4920FCZZ PCAPH0004YSZZ XWHS730-05070 UCLEZ0164FCZZ PMLT-1296FCZZ (Unit) CBOX-0125DS51
Inter- PRICE NEW PART change RANK MARK RANK AP C DV harness AA C Screw(38) AF C DV R cover AC C Screw(38) AF C Idle gear fixing plate AF C Idle gear 29T AA C E type ring(E4) AC C MG gear(22T) AA C E type ring(E5) AL C MG holder R AC C MX gear B(31T) AD C MX gear A(34T) AH C MX bearing AB C Screw(316K) BH C MG roller AS C DV doctor N AR C MX roller A AR C MX roller B AC C SRU handle AH C DV cover BF C DV shutter AE C Shutter cover AB C DV shutter spring AD C DV lock lever AC C F handle spring AE C DV F handle AA C Screw(48) AC C M4 plate AL E Initial detect DV PWB unit AC C PP plate AH C MG holder F AS D DV BOX AC A DV side seal F AX B ATC sensor AA C Screw(36) AC C DV spring AD C DV joint arm AC A DV side seal R AE C Bottom cover AA C SHT side cushion AG C Cushion AC C DV seal 2 AA C DV-BOX cushion AC C Doctor cushion R AC C Doctor suede AE C DV shutter suede N AA C SHT side sheet AC D Cap D AA C Washer AG A DV blead AH C Shutter cushion BD E DV unit
DESCRIPTION
TR No.
Effective time
13-1
I DV unit[AR-M312U,AR-M420U]
28 2 1 16 3 4 5 6 7 7 12 7 13 14 7 11 7 13 50 54 8 9 10 29 47 15 19 18 17 51 20
45
22
23
46
52 49
28
24 45 52
55
50
a
25
26 27
56 29 43 48 41 42 39 40 38 44 32 48 37 36 35
a b
54 14 13 29 9 4 13 7 53
28
FCP09293
manuals4you.com
13-2
Update : 2006/05/31
PARTS CODE
PDUC-0165FCZ1 PFILZ0285FCZ1 XBBS740P08000 XEPS740P35000 NFANP0076FCZZ XHBS740P08000 PDUC-0163FCZZ PDUC-0162FCZZ PCOVP1555FCZ1 DHAI-3674FCZZ PBOX-0150FCZZ PDUC-0183FCZZ PDUC-0182FCZZ LPLTM6461FCZZ NFANP0073FCZZ NFANP0082FCPZ CPWBN1633FCE2 XBBSD40P30000 CBOX-0149FC01 LPLTM6458FCZZ DHAI-3197FCZZ DUNT-7093DS17 DUNT-7093DS18 LX-BZ0964FCZZ LPLTM5769FCZ1 LPLTM6457FCZZ LX-BZ0921FCZ2 XBPSD25P06000 PMLT-1397FCZZ LPLTM5767FCZ1 DHAI-3642FC11 LX-BZ0922FCZZ JHNDP0156FCZZ PDUC-0164FCZ1 QCNCM1001FCZZ LPLTM6465FCZZ PCOVP1560FCZZ PCOVP1817FCZZ LX-BZ0026GCZ1 LHLDW1006FCZZ XHBSD30P06000 XEBSD40P10000 PSHEP5009FCZZ PSHEP4945FCZZ PSHEZ4904FCZZ XBPSD30P06000 MSPRP3016FCZZ DUNT-7314FC12 PCOVP1557FCZZ XBBSE30P06000 XBBSD30P06000 PCOVP1629FCZZ DHAI-3673FCZZ VHI28F322LD4F VHI28F322LD8F VHI28F322LE1F VHI28F322LD5F
55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70
VHI28F322LD9F VHI28F322LE2F LX-BZ0725FCZZ RMOTP0910FCPZ PCOVP1814FCZZ LHLDW1285FCZZ DHAI-3650FCZZ LPLTM6464FCZZ DUNT-7388FCPZ DUNT-7681FCPZ LPLTM6258FCZ2 LX-BZ1022LCZZ PCUSG0378FCZZ CCOVP1815FC01 JHNDM0177FCZZ LX-BZ0975FCZZ CRALM0221FC01 CRALM0222FC01
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AF D Controller duct AT A Ozone filter AA C Screw(48) AC C Screw(435) AX B Duct fan AA C Screw(48) AG D Main duct 2 AG D Main duct 1 AE C Controller BOX cover AE C Motor earth harness AS C Controller BOX upper AG D BOX cooling duct R AH D BOX cooling duct lower AF C BOX fan fixing plate BB B Fan motor(12V) 1 BF B Fan motor(12V) BL E Mother board AA C Screw(430) AX D Control box lower AG C Paper exit cabinet fixing plate AE C DSW interface harness CB E LSU unit(35) [AR-M351N/U,AR-M355N/U] CB E LSU unit(45) [AR-M451N/U,AR-M455N/U] AB C Screw AG C Operation cabinet fixing plate B AT C LSU top plate AF C Scanner screw AA C Screw(2.56) AC C Rear duct cushion AE C Fusing drawer fixing plate AX C Fusing interface harness AC C Screw AE C Handle R AK C Sub duct AC C Connector(BU04P-TR-PH) AG C Control joint plate AC C FAX I/F cover AC C D/SW cover AC C Screw AA C Mini clamp(UAMS-09-0) AA C Screw(36) AA C Screw(410) AC C Control duct sheet A AC C Control duct sheet B AD C Duct sheet AA C Screw(36) AR C LSU earth plate BK E Soft NIC unit [AR-M351N,AR-M355N,AR-M451N,AR-M455N] AC C LAN/option cover [AR-M351U,AR-M355U,AR-M451U,AR-M455U] AA C Screw(36) AA C Screw(36) AG C Right noise cover AE C Paper exit earth harness MFP flash ROM A EX(28F322LD4F) BE B [AR-M351N,AR-M355N,AR-M451N,AR-M455N] BE B MFP flash ROM A EX(28F322LD8F) [AR-M355U,AR-M455U] BE B MFP flash ROM A EX(28F322LE1F) [AR-M351U,AR-M451U] MFP flash ROM B EX(28F322LD5F) BE B [AR-M351N,AR-M355N,AR-M451N,AR-M455N] BE B MFP flash ROM B EX(28F322LD9F) [AR-M355U,AR-M455U] BE B MFP flash ROM B EX(28F322LE2F) [AR-M351U,AR-M451U] AB C 4/5 adjustment screw BF B Polygon motor AG C Harness protect cover AC C Edge holder(EH11) AR C FM CNT harness AQ C PWB fixing plate CD E HDD(40GB) [AR-M351N,AR-M355N,AR-M451N,AR-M455N] 1 CD E HDD(40GB) [AR-M351N,AR-M355N,AR-M451N,AR-M455N] AE C HDD fixing plate [AR-M351N,AR-M355N,AR-M451N,AR-M455N] AB C Screw [AR-M351N,AR-M355N,AR-M451N,AR-M455N] AF C Cushion [AR-M351N,AR-M355N,AR-M451N,AR-M455N] AP C HDD cover [AR-M351N,AR-M355N,AR-M451N,AR-M455N] AD C HDD handle [AR-M351N,AR-M355N,AR-M451N,AR-M455N] AC C HDD fixing screw [AR-M351N,AR-M355N,AR-M451N,AR-M455N] AK C HDD rail F AK C HDD rail R
TR No.
Effective time
06/07 R/C
06/04
14-1
Update : 2006/05/31
PARTS CODE
PFTA-0147FCZZ DHAI-3664FC11 LPLTP6470FCZZ MSPRC3328FCZZ LX-BZ0266FCZZ QCNW-0225FCZZ PSHEZ5339FCZZ DHAI-3651FCZZ PMLT-1369FCZZ LHLDW1600FCZZ PDUC-0184FCZZ PMLT-1394FCZZ RCORF0046FCZZ LRTNP0012FCPZ CPLTM6464DS53 CPLTM6464FC56 CPLTM6464DS56
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AF C HDD cover AX C Mother PWB interface harness AC C PWB slide lock plate AC C PWB slide spring AB C Screw AH C Mother interface FFC AC C BOX interception sheet BC C HDD interface cable AC C HDD core cushion AC C Holder(FCR-60 V0) AH D BOX cooling duct upper AC C Duct between cushion AH C Core AD C Retainer CU E Controller unit [AR-M351N,AR-M355N,AR-M451N,AR-M455N] CT E Controller unit [Missing parts code][AR-M355U,R-M455U] 1 CV E Controller unit [AR-M355U,AR-M455U]
TR No.
Effective time
51
501
32
c b 76 72 59
65 65 68 51 68 64 52
6 84 42 29 FCP09294 30 28 53 6 48 6 41
22 6 23 21 6 57 22
manuals4you.com
14-2
PARTS CODE
PDUC-0165FCZ1 PFILZ0285FCZ1 XBBS740P08000 XEPS740P35000 NFANP0069FCZZ XHBS740P08000 PDUC-0163FCZZ PDUC-0162FCZZ PCOVP1555FCZ1 DHAI-3177FCZZ PBOX-0127FCZ2 NFANP0062FCZZ XBPS740P30000 QCNW-0201FCZZ CPWBN1460FCE5 LPLTM5758FCZZ CBOX-0128FC02 LPLTM5768FCZZ DHAI-3197FCZZ DUNT-7093DS12 DUNT-7093DS11 LX-BZ0964FCZZ LPLTM5769FCZ1 LPLTM5729FCZZ LX-BZ0921FCZ2 LPLTM5767FCZ1 DHAI-3169FCZZ LX-BZ0922FCPZ JHNDP0156FCZZ PDUC-0164FCZ1 CPWBX1645FC51 LPLTM5765FCZ4 LHLDW1006FCZZ XHBS730P06000 XEBS740P10000 PSHEP5009FCZZ PSHEP4945FCZZ PSHEZ4904FCZZ XBPS730P06000 MSPRP3016FCZZ XHBS730P06000 XBBS730P06000 PCOVP1629FCZZ DHAI-3333FCZZ LX-BZ0725FCZZ RMOTP0910FCZZ LPLTM5757FCZ1 LRTNP0012FCPZ CPLTM5757FC66
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AF C Controller duct AT B Ozone filter AA C Screw(48) AC C Screw(435) AV B Fan AA C Screw(48) AG C Main duct 2 AG C Main duct 1 AE C Controller BOX cover AD C Motor earth harness AQ D Controller BOX upper AX B Fan AB C Screw(430) AG C Printer interface FFC AS E Mother board unit AK C M/B fixing plate AX E Control box lower AM C Paper exit cabinet fixing plate A AE C DSW interface harness CE E LSU 31 unit BS E LSU 45 unit AB C Screw AG C Operation cabinet fixing plate B AT C LSU top plate AF C Scanner screw AE C Fusing drawer fixing plate AT C Fusing interface harness AC C Screw AE C Handle R AK C Sub duct CM E STD control PWB unit AG C Control joint plate AA C Mini clamp(UAMS-09-0) AC C Screw(36) AA C Screw(410) AC C Control duct sheet A AC C Control duct sheet B AD C Duct sheet AA C Screw(36) AR C LSU earth plate AC C Screw(36) AC C Screw(36) AG C Right noise cover AE C Paper exit earth harness AB C Handle fixing screw BF B Polygon motor AP C Control joint plate AD C Retainer CN E Controller unit
TR No.
Effective time
[AR-M312U] [AR-M420U]
15-1
3 6
51 47 50 25
51 47 25
10 50 56
a
11 6 6
34 51 56 35 51 51 51 51 51 6 12
501
6 6
6 13 42
61
43
6 6 6 51 6 16 6 51 52 51 18 17 42 14
14
32
a
41 41 31 6 41
29 46 6 29 41 6 6 6 62 48 42 6 53 6 6 24 23 6
19 22 57
21 22
28 30 29
FCP09295
manuals4you.com
15-2
PARTS CODE
RDENC0036FCZ3 RDENC0020FCZ6 RDENC0037FCZ3 RDENC0021FCZ6 CPWBF1558FC32 XBPS730P08K00 LSUPP0118FCZZ XHBS740P08000 LBSHZ1001ACZZ LPLTM5941FCZZ LBSHZ2006SCZZ LPLTM5766FCZZ QSW-C1381QCZZ DHAI-3646FCZZ LPLTM5756FCZ1 LSUPP0128FCZZ LPLTM5942FCZ1 LSUPP0115FCZZ DHAI-3282FCZZ DHAI-3638FCZZ XBBS740P08000 DHAI-3665FC12 DHAI-3430FCZZ DHAI-3645FC11 DHAI-3431FCZZ CPWBF1629FCE1 CPWBF1629FCE2 DHAI-3667FCZZ DHAI-3253FCZZ XBPS730P08K00
DESCRIPTION
AC/DC power supply PWB 100 AC/DC power supply PWB 100 AC/DC power supply PWB 200 AC/DC power supply PWB 200 Reactor PWB Screw(38K) Supporter(SPLSN6) Screw(48) Bushing Filter PWB fixing plate Bushing(NRP-345) Main switch fixing plate Switch MSW interface harness Power supply unit fixing plate Spacer(L10) Harness protect plate Supporter(SPLSN3) LSU interface harness LSU interface harness Screw(48) AC/DC harness 100 [100V AC/DC harness 100 AC/DC harness 200 [200V AC/DC harness 200 Relay PWB [100V Relay PWB [200V Filter interface harness [200V Filter interface harness Screw(38S) [100V series] [Except AR-M312U,AR-M420U] [100V series][AR-M312U,AR-M420U] [200V series] [Except AR-M312U,AR-M420U] [200V series][AR-M312U,AR-M420U] [200V series] [200V Series] [200V Series] [200V Series] [200V Series]
TR No.
Effective time
[Except AR-M312U,AR-M420U] [Except AR-M312U,AR-M420U] [200V series] [AR-M312U,AR-M420U] [Except AR-M312U,AR-M420U] Series][Except AR-M312U,AR-M420U] [100V Series][AR-M312U,AR-M420U] Series][Except AR-M312U,AR-M420U] [200V Series][AR-M312U,AR-M420U] Series][Except AR-M312U,AR-M420U] Series][Except AR-M312U,AR-M420U] Series][Except AR-M312U,AR-M420U] [200V Series][AR-M312U,AR-M420U] [Except AR-M312U,AR-M420U]
21 22 23
4 3 a c 19 5 19 5 5 8 6 17 7 4
16
5 5 b 14 15 15 FCP09296 15 15 21 23 23 12
16-1
ma
nu
13
als
10 5
4y
ou
.co
Update : 06/02/27
PARTS CODE
NFANP0069FCZZ XEPS740P35000 PDUC-0161FCZ1 XHBS740P06000 PSHEZ4874FCZ1 PSHEZ4873FCZ1 XHBS730P06000 DHAI-3236FCZZ QSW-M0502FCPZ XBBS730P14000 LPLTM5775FCZZ XHBS730P06000 PCOVP1528FCZ2 XHBS740P08000 PCOVP1529FCZZ MSLI-0141FCZZ NSFTZ2677FCZZ LX-BZ0817FCZZ MLEVP0780FCZZ XRESP30-06000 MLEVP0779FCZZ PGIDH1883FCZZ JHNDP0152FCZZ NSFTZ2571FCZZ MSPRT2834FCZZ LPLTM5710FCZZ NSFTZ2570FCZZ LDAIU0623FCZZ LX-BZ0960FCZZ PCLR-0441FCZZ PCLR-0519FCZZ LHLDW1006FCZZ LRALP0186FCN1 PSHEZ4885FCZ1 JHNDP0155FCZZ LDAIU0622FCZZ LDAIU0622FCZ1 PSHEZ4884FCZZ LX-BZ0833FCZZ XHBS740P08000 XHBS740P08000 GLEGG0075FCZZ
44 46 47 48 49 51 52 53 54 55 56 57 58 59 501
LHLDZ1705FCZZ LHLDZ1705FCZZ MSPRP2963FCZZ LPLTM5707FCZZ LHLDZ1455FCZZ XEBS740P12000 CCASZ0311DS51 CCASZ0296DS51 XEBS740P10000 TCAUS1038FCZZ TLABZ4432FCZZ PCOVP1693FCZZ LSTYM0255FCZ1 LPLTM5708FCZ2 LPLTM5708FCZ3 LRALM0178FCZZ XHBS740P10000 CGIDH1883DS51
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AV B Fan AC C Screw(435) AH D Duct AA C Screw(46) AC C LSU cleaning sheet R AC C LSU cleaning sheet F AC C Screw(36) AF C DSWF harness AH B Door switch(AM51632C531N) AA C Screw(314) AC C Switch fixing plate AC C Screw(36) AK D Front cover right AA C Screw(48) AQ D Front cover AS C Slide rail AL C Fusing guide shaft AA C Screw AC C DV pressure lever B AA C E type ring(E3) AC C DV pressure lever A AN C DV guide AG C DV guide handle AE C DV guide shaft AD C DV guide spring AF C DV guide plate AE C DV shaft AU C Bottom plate AC C Screw AK C Collar(16) 1 AE C Collar(16) AA C Mini clamp(UAMS-09-0) AX D Right rail AB C Paper feed base sheet R AF C Handle F AY C Paper feed base plate 5 AU C Paper feed base plate [Unleaded correspondence][With No.57] AF C Paper feed base sheet L AC C Screw [Except AR-M312U,AR-M420U] Screw(48) [Productivity improvement][With No.44] 5 AA C [Except AR-M312U,AR-M420U] AA C Screw(48) [AR-M312U,AR-M420U] AE D Rubber foot [Except AR-M312U,AR-M420U] Positioning holder [Productivity improvement][With No.43] 5 AC D [Except AR-M312U,AR-M420U] AC D Positioning holder [AR-M312U,AR-M420U] AC C Process earth spring AU C Rear fixing plate AD C Multi position holder AA C Screw(412) AP E Paper powder remove case unit [Except AR-M312U,AR-M420U] BA E Paper powder remove case unit [AR-M312U,AR-M420U] AA C Screw(410) AD D Laser caution label AC D NO1 label AH C Duct support cover AL C Duct support plate AT C Front fixing plate 5 AR C Front fixing plate [Unleaded correspondence][With No.40] AP C Process rail AA C Screw(410) BF E DV guide
TR No.
Effective time
06/05
05/09
05/04
05/04
05/09
manuals4you.com
17-1
Update : 06/02/27
16 16
16 16
16 48
manuals4you.com
52
51
501
34 33 32 52 52 52 52 52 FCP09297
17-2
Update : 06/02/27
PARTS CODE
MSLI-0141FCZZ CPLTM5895FC01 XBPS720P02500 MLEVP0831FCZZ XRESP40-06000 RPLU-0326FCZ2 LHLDW1006FCZZ LPLTM5709FCZZ RMOTP0875FCZZ RMOTP0906FCZZ RMOTP0907FCZZ LPLTM5761FCZZ XHBS740P08000 DHAI-3167FCZZ MSPRC2962FCZZ LX-BZ0932FCPZ NGERH1379FCZZ LDAIU0624FCZZ RMOTD0858FCPA XEBS730P08000 MARMP0252FCZZ CPWBF1598FCE1 CPWBX1637DS60 CPWBX1637FCF0 CPWBX1637DS63 CPWBX1637FCF3 CPWBX1637DS61 CPWBX1637FCF1 CPWBX1637DS64 CPWBX1637FCF4 CPWBN1515FCE3 CPWBN1461FCE4 DHAI-3635FCPZ DHAI-3199FCZZ DHAI-3200FCZZ QSOCA0097FCZZ QSOCA0096FCZZ DHAI-3172FCZZ LHLDW1263FCZZ LPLTM5760FCZ3 LPLTM6463FCZ1 CPWBF1626FCE1 CPWBF1627FCE2 CPWBF1641FCE3 LHLDF2330RCZZ RDENU0038FCZZ RDENU0022FCZ1 LHLDZ1449FCZ1 RMOTD0856FCZZ MSPRC0024QSZZ NCPL-0045FCZZ LBSHC0090FCZZ LPLTM5707FCZZ XRESP30-06000 MSPRC2644FCZZ MSPRC2671FCZZ XEBS740P10000 QCNW-0205FCZZ QCNW-0204FCZZ QCNW-0203FCZZ LPLTM5755FCZZ VHI28F081L39F XBBS730P06000 XBPS730P06K00 DHAI-3831FCZZ DHAI-3176FCZZ XBPS740P06K00 PCOVP1623FCZZ XHBS730P06000 PMLT-1277FCZZ PMLT-1278FCZZ DHAI-3144FCZZ LX-BZ0901FCPZ PTUBU0134FCZZ DHAI-3647FCZZ RCORF0046FCZZ CDAIU0624DS51 CPLTM6463DS52 CPLTM5760DS59 CPLTM6463DS53
26
28 31 32 33 34 35 36 ! ! ! ! ! 38 40 42 43 44 45 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 64 65 66 67 68 69 70 76 77 83 501 502
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AS C Slide rail AD C Solenoid fixing plate AA C Screw(22.5) AC C Separation pawl lever AA C E type ring(E4) AN B Separator pawl solenoid AA C Mini clamp(UAMS-09-0) AD C Lift up fixing plate BN B Drum motor BF B Main motor 35 [AR-M351N/U,AR-M355N/U,AR-M312U] BF B Main motor 45 [AR-M451N/U,AR-M455N/U,AR-M420U] AG C Rear cabinet fixing plate A AA C Screw(48) AP C Main drive interface harness AA C Left cabinet spring AC C Screw AC C Lift up gear AG D Lift up base plate BS B Lift up motor AC C Screw(38) AD C Size detect switch arm AG E Cassette detect PWB BX E PCU PWB [AR-355N/U,AR-M351N/U](100V Series) 1 BX N E PCU PWB [AR-355N/U,AR-M351N/U](100V Series) BX E PCU PWB [AR-455N/U,AR-M451N/U](100V Series) 1 BX N E PCU PWB [AR-455N/U,AR-M451N/U](100V Series) BV E PCU PWB [AR-M351N/U](200V Series) 1 CA N E PCU PWB [AR-M351N/U](200V Series) BV E PCU PWB [AR-M451N/U](200V Series) 1 CA N E PCU PWB [AR-M451N/U](200V Series) BW E PCU PWB [AR-M312U] BW E PCU PWB [AR-M420U] AY C DV interface harness AP C AC harness [Except AR-M312U,AR-M420U] AG C AC harness [AR-M312U,AR-M420U] AN C Outlet connector [AR-M312U,AR-M420U] AK C Inlet(NC-176-1.0) AD C Outlet harness [AR-M312U,AR-M420U] AC C Wire holder(EDS0607M) AL C Inlet fixing plate [AR-M312U,AR-M420U] AM C Inlet fixing plate [Except AR-M312U,AR-M420U] AU E Fuse PWB (100V series) AW E Fuse PWB (200V series)[Except AR-M312U,AR-M420U] AU E Fuse PWB (200V series)[AR-M312U,AR-M420U] AB C PWB holder(LCBS-04N) BS E High voltage transformer [Except AR-M312U,AR-M420U] BS E High voltage transformer [AR-M312U,AR-M420U] AK D High voltage holder BA B Toner motor AA C Hopper spring AC C Hopper coupling AA C Bushing AU C Rear fixing plate AA C E type ring(E3) AB C Size detect switch spring AB C Lift up gear spring AA C Screw(410) AC C HV interface FFC AC C Drum motor interface FFC AD C Main motor interface FFC AR C PCU fixing plate AY B PCU flash ROM(28F081L39) [Except AR-M312U,AR-M420U] AC C Screw(36) AA C Screw(36K) AK C Noise earth harness AC C AC earth harness [AR-M312U,AR-M420U] AA C Screw(46K) AD C FAX connector cover [Except AR-M312U,AR-M420U] AC C Screw(36) AC C Seal cushion A AD C Seal cushion B AK C Hopper interface harness AC C Screw AC C Tube AN C Inlet harness AH C Core [AR-M312U,AR-M420U] BN E Lift up unit BA E Inlet fixing plate unit (100V series)[Except AR-M312U,AR-M420U] BB E Inlet fixing plate unit (100V series)[AR-M312U,AR-M420U] BB E Inlet fixing plate unit (200V series)[Except AR-M312U,AR-M420U]
TR No.
Effective time
manuals4you.com
18-1
Update : 06/02/27
PARTS CODE
CPLTM5760DS60
Inter- PRICE NEW PART change RANK MARK RANK BC E Inlet fixing plate unit
DESCRIPTION
(200V series)[AR-M312U,AR-M420U]
TR No.
Effective time
69 b
50
8 16 16 48 49 47 45 44 23 16 16 43 50 54 40 60 77 59 36 64 64 16 16 57 16 83 62 76 76 32 33 59 31 16 59 7 38 40 21 42 64 61 58 26 24 51 59 69 i 28 b 66 66
f g h
16 16 53 12
16 14 56
55 15 53 17 18 16 16
501
20 52 19
16 16
502
34
22 23 25
c h 7 a f g
AR-M312U,AR-M420U 35
77 60 38 40 40
64 71 61 36
502
7
64 16
76
35 33
31 FCP09298
65
66
18-2
O Cassette unit
NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
PARTS CODE
LPLTM5735FCZZ MLEVP0754FCZZ LPLTP5413FCWZ LHLDW1226FCZZ MSPRC2641FCZ1 PSHEZ3130FCZZ GCASP0175FCNZ LHLDZ1377FCZZ XEBS740P08000 PTME-0280FCZZ PCOVP1545FCNZ CPLTM5736FC01 XRESP70-08000 NGERH1378FCZZ LPINS7062SCZZ MSPRC2851FCZZ MLEVP0755FCZ1 MSPRC2631FCZZ LPLTP5733FCZZ PTPE-0243FCZ1 NGERH0193FCZZ LPLTP5734FCZZ LX-BZ0884FCPZ PTME-0281FCZZ PGIDH1833FCZ1 TLABZ5148FCZZ TLABG0401QSZZ (Unit) CCASP0175FC34
Inter- PRICE NEW PART change RANK MARK RANK AR C Turn plate AF C Rear plate lever AE C Rear edge plate AB C Turn fastener AB C Rear plate spring AB C Rotation plate sheet BA D Cassette AD C Rear plate holder AA C Screw(48) AD C Cassette pawl right AL D Cassette front cover AP C Lift plate AA C E type ring(E7) AD C Sector gear AA C Pin(316) AB C Cassette earth spring AE C Side plate F lever AC C Side plate F lever spring AH C Side plate F AC C Side plate tape AB C UC manual feed gear AG C Side plate R AB C Screw AD C Cassette pawl left AC C Side plate guide Energy star label AC D AR BG D E Energy star label
DESCRIPTION
TR No.
Effective time
901
O Cassette unit
20 25 22 23 21 25 20 19 6 18 17 23 21 8 7 1 4 5 3 2
9 16 14 15
9 10
9 13
9 12 24 9 FCP09299 26 11
manuals4you.com
19-1
PARTS CODE
TCADZ1718FCZZ SPAKA6236FCZZ TCADZ1275FCZZ LHLDW1226FCZZ QACCD7912QCPZ QACCB7623QCZZ QACCVR621QCPZ
Inter- PRICE NEW PART change RANK MARK RANK AE D Fusing pressure manual AD D Cassette protect add AB D Cassette rotation tag AB C Turn fastener AS B AC cord AC cord AQ B AQ BA BB BB BB BB BB AQ AZ AM AL BB B B B B B B B B B D D D D D D D D N D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D AC cord AC cord AC cord AC cord AC cord AC cord AC cord AC cord AC cord Accessory case CD-ROM CD-ROM CD-ROM CD-ROM CD-ROM CD-ROM(NIC) CD-ROM(NIC) MSDS card MSDS card Maintenance card Inst.card Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual Operation manual
DESCRIPTION
TR No.
Effective time
10
11
12
QACCLR624QCPZ DHAI-3332DS11 DHAI-3332DS12 DHAI-3332DS13 DHAI-3332DS14 DHAI-3332DSZZ QACCJ6911QCZZ QACCR7621QCZZ SPAKA6692FCZZ CDSKA0029FC34 CDSKA0030FC32 CDSKA0030GH31 CDSKA0029GH31 CDSKA0042FC31 CDSKA0032GH31 CDSKA0032FC31
[U.S.A,Canada,LAG2] [U.kingdom,Yemen,Soudi arabia, Bahrain,Kuwait,UAE,Oman,Qutar] [Europe,Lebanon,Iran,West africa,Pakistan, STCL,Egypt,Jordan,Syria,Tunisia,Morocco] [Australia,New Zealand] [South africa,India] [Israel] [Hong kong] [Soudi arabia(127V)] [Singapore,Sri Lanka,Indonesia] [Phillipines] [Argentina]
BB
N N N
BH AE AB AC BA N N N N N N N N N N N N N N N N BD
14 15 17
20
TCADZ1706FCZZ TCADZ1706GHZZ CCADZ1518FC01 TCADS1511FCZZ TINSE2880FCZ1 TINSE2882GHZZ TINSE2881FCZ1 TINSF2884GHZZ TINSG2883GHZZ TINSZ2895GHZZ TINSI2886GHZZ TINSH2887GHZZ TINSW2888GHZZ TINSZ2889GHZZ TINSZ2890GHZZ TINSD2891GHZZ TINSZ2892GHZZ TINSZ2893GHZZ TINSS2885GHZZ TINSZ2894GHZZ TINSR2896GHZZ TINSP2897GHZZ TINSE2899FCZ1 TINSE2881FCZ1 TINSF2884FCZ1 TINSE2902FCZZ TINSE2904GHZZ TINSE2903FCZZ TINSF2906GHZZ TINSG2905GHZZ TINSZ2917GHZZ TINSI2908GHZZ TINSS2907GHZZ TINSH2909GHZZ TINSW2910GHZZ TINSZ2911GHZZ TINSZ2912GHZZ TINSD2913GHZZ TINSZ2914GHZZ TINSZ2915GHZZ TINSZ2916GHZZ TINSR2918GHZZ TINSP2919GHZZ TINSF2906FCZZ TINSS2907FCZZ TINSZ2920FCZZ TINSE2840FCZZ TINSE2840GHZZ TINSF2842FCZZ TINSS2843FCZZ TINSG2841GHZZ TINSF2842GHZZ TINSS2843GHZZ
AL BD BH AM N N N N N N N N N N N N N N N N AT
AT BA BA AN N BB BB N N N
[Europe] [Europe] [Europe] [Taiwan] [AR-M351N,AR-M451N][Europe] [AR-M351N,AR-M355N,AR-M451N,AR-M455N] [Except Europe] [U.S.A,Canada,U.Kingdom] [U.Kingdom] EX [Except U.Kingdom] [Europe(Except U.Kingdom)] (Copy) [English(U.S.A)][AR-M355N/U,AR-M455N/U] (Copy) [English(U.Kingdom)][AR-M351N] (Copy) [English(Other)][AR-M351N] (Copy) [French][AR-M351N] (Copy) [German][AR-M351N] (Copy) [Greek][AR-M351N] (Copy) [Italian][AR-M351N] (Copy) [Dutch][AR-M351N] (Copy) [Swedish][AR-M351N] (Copy) [Norwegian][AR-M351N] (Copy) [Finnish][AR-M351N] (Copy) [Danish][AR-M351N] (Copy) [Hungarian][AR-M351N] (Copy) [Czech][AR-M351N] (Copy) [Spanish][AR-M351N] (Copy) [Polish][AR-M351N] (Copy) [Russian][AR-M351N] (Copy) [Portuguese][AR-M351N] (Copy) [English(Hong Kong)][AR-M351U] (Copy) [English(Other)][AR-M351U] (Copy) [French][AR-M351U] (Key) [English(U.S.A)][AR-M355N/U,AR-M455N/U] (Key) [English(U.Kingdom)][AR-M351N] (Key) [English(Other)][AR-M351U/N] (Key) [French][AR-M351N] (Key) [German][AR-M351N] (Key) [Greek][AR-M351N] (Key) [Italian][AR-M351N] (Key) [Spanish][AR-M351N] (Key) [Dutch][AR-M351N] (Key) [Swedish][AR-M351N] (Key) [Norwegian][AR-M351N] (Key) [Finnish][AR-M351N] (Key) [Danish][AR-M351N] (Key) [Hungarian][AR-M351N] (Key) [Czech][AR-M351N] (Key) [Polish][AR-M351N] (Key) [Russian][AR-M351N] (Key) [Portuguese][AR-M351N] (Key) [French][AR-M351U] (Key) [Spanish][AR-M351U] (Key) [Arabic][AR-M351U] (PCL inst) [English] (PCL inst) [English] (PCL inst) [French] (PCL inst) [Spanish] (PCL inst) [German] (PCL inst) [French] (PCL inst) [Spanish]
20-1
Effective time
20
22 23 25 26 27 28
101
102 103
manuals4you.com
20-2
12
14 15 17
22
20
11 25 10 23 28 27 7 9
8 26 FCP09300
20-3
PARTS CODE
SSAKZ0002QSZZ CPAKA6127FC01 TCADZ1718FCZZ SPAKA6236FCZZ TCADZ1275FCZZ LHLDW1226FCZZ QACCVR621QCPZ DHAI-3332DSZZ QACCB7623QCZZ DHAI-3332DS11 DHAI-3332DS13 DHAI-3332DS14 QACCR7621QCZZ QACCD7912QCPZ DHAI-3332DS12 SPAKA6235DSZZ CCADZ1518FC01 TCADS1511FCZZ TINSE3065FCZZ TINSE3069FCZZ TINSF3066FCZZ TINSZ3068FCZZ TINSE3071FCZZ TINSF3072FCZZ TINSZ3074FCZZ SSAKA2440QCZZ SSAKA5003CCZZ UBNDA0001FCZZ SPAKA6256FCZZ SPAKA6265FCZZ SPAKA6272FCZZ GCOVZ0237FCZZ TCAUS0009QSZZ
10
11 15 17
20
22 23 25 26 27 28 103 105
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AF D Vinyl bag AF D Packing case lower AE D Fusing pressurization manual AD D Packing add AB D Cassette rotation tag AB C Turn fastener AQ B AC cord [Iran,Tunisia] BB B AC cord [Singapore] AQ B AC cord [Saudi arabia(250V),Yemen,Bahrain,Kuwait,UAE,Oman,Qutar] BB B AC cord [South Africa,Sli Lanka,India] BB B AC cord [Hong kong] BB B AC cord [Saudi arabia(127V)] AZ B AC cord [LAG4] AS B AC cord [LAG2] BB B AC cord [Special country] AH D Joint AB D Maintenance card EX AC D Inst.card [Germany,Holland,Sweden] BF D OP manual [English] BF D OP manual [English](Hong Kong) BP D OP manual [French] BP D OP manual [Arabic] AZ D OP manual(Copy) [English] BD D OP manual(Copy) [French] BD D OP manual(Copy) [Arabic] AB D Vinyl bag(280410mm) AA D Vinyl bag(140260mm) AA C Band (200V Series) AD D Cabinet protect add AC D Fusing protect add AG D Fusing protect add R Dust cover [Tunisia,Saudi Arabia,Yemen, AZ D Bahrain,Kuwait,UAE,Oman,Qutar] AF D Plug caution label [LAG4]
TR No.
Effective time
15 17 20 22
1 6 25 10 23 11 7 9 27 2 11 26 11
11 28
8 FCP09301
manuals4you.com
21-1
Update : 06/02/27
R Mother PWB
NO.
1 2 3 4 5 6 8 9 10 11 12 13 14 15 16 17 18 20 21 901
PARTS CODE
QCNCM1225FCPZ QCNCW1222FCPZ QCNCM1224FCPZ QCNCM1223FCPZ PRDAR0057FCZ1 VCEAZA1VW107M VHDDSM1D1//-1 VHD10JDA10+-1 VHINJM7812A-1 VRS-RE3LA6R2J QFS-C0048PAZZ QFS-C0054PAZZ QFSHD0002QCZZ RC-EZ0357FCPZ RCNVD0005FCZZ RCNVD0004FCZZ XBBS730P06000 RC-KZ1054CCN2 RCNVD0007FCZZ QFS-C0057PAZZ (Unit) CPWBN1633FCE2
! !
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AM C Connector(TX25-80P-LT-H1 E) AK C Connector(30pin) AF C Connector(B9PS-VH LF) AD C Connector(S08B-PASK-2 LF) AS C Heat sink(C16PUG16-30) AC C Capacitor(35WV 100F) AB B Diode(DSM1D1) 1 AB B Diode(10JDA10) AH B IC(NJM7812A) AC C Resistor(3W 6.2 5%) AE A Fuse(3.15A) AD A Fuse(6.3A) AA C Fuse holder(H-0032-2) AD C Capacitor(16WV 470F) BR B DC-DC Converter[3.3V](MPD6S002T) BU B DC-DC Converter[12V](MPD6S009) AC C Screw(36) AB C Capacitor(50WV 0.1F) BS B DC-DC Converter[5V](MPD5S023) AE A Fuse(800mA) BL E Mother board
TR No. [CN1] [CN2] [CN3] [CN4] [IC1] [C1] [D1] [D1] [IC1] [R1] [F1] [F2] [F1,F2,F3] [C3,C5,C7,C9,C18] [IC2] [IC3] [IC1] [C11,C12,C13,C14,C15] [IC4] [F3]
Effective time
06/05 R/C
22-1
Update : 06/02/27
S PCU PWB
NO.
1 2 3 4 5 6
PARTS CODE
RFILN0047FCZZ RMPTR4103ACZZ RMPTR4103ACZZ RMPTR4330ACZZ RMPTR4330ACZZ RMPTR4472ACZZ VCCCCZ1HH100D VCCCCZ1HH101J VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1EF223Z VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYTV1CB105K VCKYTV1AB225M VCKYCZ1HB222K VHDDAN202U/-1 VHDDAP202U/-1 VHDDA204U//-1 VHDDA204U//-1 VHDDA204U//-1 VHDMA704A//-1 VHDCRH01+++-1 VHI82805GNA-1 RH-IX0037QSPZ VHILM324D++-1 VHILM339D++-1 VHID62503FG-1 VHI74VHCT240X VHI74VHCT244X VHVICPS1.2/-1 VRS-CZ1JD000J VRS-CZ1JD000J VRS-CZ1JD000J VRS-CZ1JD000J VRS-CZ1JD000J VRS-CZ1JD000J VRS-CZ1JD101J VRS-CZ1JD102J VRS-CZ1JD102J VRS-CZ1JD102J VRS-CZ1JD102J VRS-CZ1JD102J VRS-CZ1JD102F VRS-CZ1JD103F VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD104J VRS-CZ1JD105J VRS-CZ1JD106J VRS-CZ1JD152F VRS-CZ1JD162J VRS-CZ1JD153F
10 11 12 13 14 15 16 17 18 21 22 23 24 25 26 27
28
29
30
31 32 33
33
34 35 36 37 38 39
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AC C Filter(MMZ1608S121AT) [NF1,NF2,NF5,NF7] AB B Block resistor(10K4) [BR18,BR28,BR29,BR30,BR31,BR32] AB B Block resistor(10K4) [BR2,BR3,BR8,BR9,BR12,BR14,BR16] AB B Block resistor(334) [BR10,BR11,BR13,BR15,BR17] AB B Block resistor(334) [BR19,BR24,BR25,BR26,BR27] AB B Block resistor(4.7K4) [BR1,BR4,BR5,BR7,BR20,BR21,BR22,BR23] AA C Capacitor(50WV 10pF) [C58,C61,C86] AA C Capacitor(50WV 100pF) [C63,C64,C71] AB C Capacitor(16WV 0.1F) [C12,C16,C42,C43,C48,C49,C53] AB C Capacitor(16WV 0.1F) [C55,C62,C72,C74,C76,C81] AB C Capacitor(16WV 0.1F) [C84,C85,C87,C88,C92,C102] AB C Capacitor(16WV 0.1F) [C104,C107,C108,C111,C114,C116] AB C Capacitor(16WV 0.1F) [C119,C120,C121,C122,C125,C127] AB C Capacitor(16WV 0.1F) [C133,C134,C137,C142,C145,C157] AA C Capacitor(25WV 0.022F) [C69,C75,C82,C93,C109,C117,C118,C143] AA C Capacitor(50WV 1000pF) [C5,C6,C7,C10,C11,C13,C17] AA C Capacitor(50WV 1000pF) [C18,C19,C20,C21,C23,C24] AA C Capacitor(50WV 1000pF) [C25,C26,C27,C28,C29,C30] AA C Capacitor(50WV 1000pF) [C31,C32,C33,C34,C35,C36] AA C Capacitor(50WV 1000pF) [C37,C38,C40,C50,C51,C52] AA C Capacitor(50WV 1000pF) [C54,C56,C57,C59,C60,C65] AA C Capacitor(50WV 1000pF) [C66,C70,C73,C78,C79,C80] AA C Capacitor(50WV 1000pF) [C83,C89,C94,C95,C97,C98] AA C Capacitor(50WV 1000pF) [C99,C100,C103,C110,C112,C115] AA C Capacitor(50WV 1000pF) [C123,C124,C130,C132,C135,C136,C141] AA C Capacitor(50WV 1000pF) [C146,C147,C150,C151,C153,C154,C39] AC C Capacitor(16WV 1F) [C156] AC C Capacitor(10WV 2.2F) [C155] AA C Capacitor(50WV 2200pF) [C1,C2,C14,C15] AB B Diode(DAN202U) [D11,D13,D19,D31,D33] AB B Diode(DAP202U) [D14,D21] AB B Diode(DA204U) [D7,D8,D9,D10,D12,D15,D16] AB B Diode(DA204U) [D17,D18,D20,D22,D23,D24] AB B Diode(DA204U) [D25,D26,D27,D35,D36,D37] AC B Diode(MA704A) [D28,D29] AC B Diode(CRH01) [D1,D2,D3,D4,D39] BA B IC(D82805GN) [IC17] AQ B SRAM(IS61LV256-15TL) [IC5] AE B IC(LM324D) [IC24] AE B IC(LM339D) [IC23,IC25] AG B IC(D62503FG) [IC6,IC7,IC8,IC13,IC14,IC20,IC21] AF B IC(74VHCT240X) [IC11] AF B IC(74VHCT244X) [IC9,IC18] AF B IC protector(ICPS1.2) [ICP1] AA C Resistor(1/16W 0 5%) [R69,R76,R77,R88,R113,R158,R159,R272] AA C Resistor(1/16W 0 5%) [Except AR-M455N/U][R62] AA C Resistor(1/16W 0 5%) (Except 200V Series)[R125] AA C Resistor(1/16W 0 5%) [R114] AA C Resistor(1/16W 0 5%) [R275,R276] AA C Resistor(1/16W 0 5%) [AR-M455N/U][R48] AA C Resistor(1/16W 100 5%) [R68,R75,R138,R150,R167,R242] AA C Resistor(1/16W 1.0K 5%) [R10,R12,R11,R26,R27,R59,R60] AA C Resistor(1/16W 1.0K 5%) [R61,R81,R82,R83,R84,R105,R107] AA C Resistor(1/16W 1.0K 5%) [R109,R121,R135,R148,R160,R163,R165] AA C Resistor(1/16W 1.0K 5%) [R177,R233,R261,R262,R263,R264] AA C Resistor(1/16W 1.0K 5%) (200V Series)[R155] AA C Resistor(1/16W 1K 1%) [R182] AA C Resistor(1/16W 10K 1%) [R206,R212,R252,R253,R268] AA C Resistor(1/16W 10K 5%) [R19,R20,R21,R22,R23,R28,R29] AA C Resistor(1/16W 10K 5%) [R30,R31,R32,R33,R34,R35,R36] AA C Resistor(1/16W 10K 5%) [R37,R38,R39,R40,R41,R46,R47] AA C Resistor(1/16W 10K 5%) [R55,R56,R63,R71,R73,R78,R80] AA C Resistor(1/16W 10K 5%) [R91,R92,R93,R95,R96,R99,R100] AA C Resistor(1/16W 10K 5%) [R101,R103,R104,R106,R108,R111] AA C Resistor(1/16W 10K 5%) [R116,R117,R118,R119,R122,R123] AA C Resistor(1/16W 10K 5%) [R124,R126,R127,R128,R133,R134] AA C Resistor(1/16W 10K 5%) [R139,R140,R141,R146,R147,R149] AA C Resistor(1/16W 10K 5%) [R151,R152,R153,R154,R157,R162] AA C Resistor(1/16W 10K 5%) [R168,R169,R172,R173,R178,R183] AA C Resistor(1/16W 10K 5%) [R184,R185,R186,R187,R188,R189] AA C Resistor(1/16W 10K 5%) [R190,R191,R192,R194,R196,R211] AA C Resistor(1/16W 10K 5%) [R213,R214,R221,R222,R223,R224] AA C Resistor(1/16W 10K 5%) [R225,R229,R235,R236,R237,R239] AA C Resistor(1/16W 10K 5%) [R243,R250,R251,R269] AA C Resistor(1/16W 100K 5%) [R210,R255,R256,R257,R258,R259,R260] AA C Resistor(1/16W 1.0M 5%) [R74,R240] AA C Resistor(1/16W 10M 5%) [R16] AA C Resistor(1/16W 1.5K 1%) [R179,R208,R254] AA C Resistor(1/16W 1.6K 5%) [R24] AB C Resistor(1/16W 15K 1%) [R171,R180]
TR No.
Effective time
manuals4you.com
23-1
Update : 06/02/27
S PCU PWB
NO.
40 41 42 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 67 72 76 77 78 79 80 81 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117
PARTS CODE
VRS-CZ1JD201J VRS-CZ1JD202F VRS-CZ1JD203J VRS-CZ1JD302J VRS-CZ1JD304F VRS-CZ1JD330J VRS-CZ1JD471J VRS-CZ1JD472F VRS-CZ1JD472F VRS-CZ1JD472J VRS-CZ1JD472J VRS-CZ1JD472J VRS-CZ1JD473F VRS-CZ1JD473F VRS-CZ1JD473J VRS-CZ1JD473J VRS-CZ1JD474J VRS-CZ1JD562J VRS-CZ1JD621F VRS-CZ1JD680J VRS-CZ1JD681F VRS-CZ1JD752J VRS-CZ1JD822F VSDTA143ZUA-1 VSDTC143ZUA-1 VSDTC143ZUA-1 VSDTC114EUA-1 VS2SK3018++-1 VS2SB1197KR-1 VS2SD1898//-1 RFILN0062FCPZ VCEASM1HM335M VCQYNA1HM103K VHPLT1D67A/-1 QSOCZ0002QSPZ QSOCZ0095FCPZ VHDRLS73///-1 VHDRLS73///-1 VHERD22FB//-1 VHIC24WC08L-1 VHIMTD13611-1 VHINJM7805A-1 VHIBD45271G-1 VHITA7291AS-1 VHITD62003AP1 VRS-TP2BD101J VRS-TP2BD122J VRS-TP2BD151J VRS-TP2BD152J VRS-TP2BD472J VRS-TP2BD391J VRS-RE3AA241J VRS-RE3DA1R0J QCNCM0671FCZZ QCNCM0878FCZZ QCNCM0923FC24 QCNCM0923FC32 QCNCM1143FCZZ QCNCM1144FCZZ QCNCM2654SCZZ QCNCM2401SC0H QCNCM5093SC0B QCNCM7014SC0H QCNCM7014SC1A QCNCM7014SC1F QCNCW0002ESZZ QCNCW1136FCZZ QCNCW1139FCZZ QCNCW1222FCPZ QCNCW0090QSZZ RCRSZ0001QSZZ RCRUB0002FCZZ RCRUB0001FCZZ (Unit) CPWBX1637DS60 CPWBX1637FCF0 CPWBX1637DS63 CPWBX1637FCF3 CPWBX1637DS61 CPWBX1637FCF1
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AA C Resistor(1/16W 200 5%) [R25,R170] AA C Resistor(1/16W 2K 1%) [R207] AA C Resistor(1/16W 20K 5%) [R66,R120] AA C Resistor(1/16W 3K 5%) [R1,R132,R193,R195] AA C Resistor(1/16W 300K 1%) [R247,R249] AA C Resistor(1/16W 33 5%) [R64,R94,R110] AA C Resistor(1/16W 470 5%) [R17,R18,R67] AA C Resistor(1/16W 4.7K 1%) [R181,R238,R244] AA C Resistor(1/16W 4.7K 1%) [R215,R218] AA C Resistor(1/16W 4.7K 5%) [R4,R5,R51,R52,R53,R72,R85] AA C Resistor(1/16W 4.7K 5%) [R86,R87,R90,R112,R129,R130] AA C Resistor(1/16W 4.7K 5%) [R164,R166,R227,R228,R232,R234] AA C Resistor(1/16W 47K 1%) [R205] AA C Resistor(1/16W 47K 1%) [R174,R175] AA C Resistor(1/16W 47K 5%) [R2,R49,R57,R65,R79,R142] AA C Resistor(1/16W 47K 5%) [R143,R144,R145,R265] AA C Resistor(1/16W 470K 5%) [R241] AA C Resistor(1/16W 5.6K 5%) [R176] AA C Resistor(1/16W 620 1%) [R246,R248] AA C Resistor(1/16W 68 5%) [R115] AA C Resistor(1/16W 680 1%) [R217,R220] AA C Resistor(1/16W 7.5K 5%) [R6,R7] AA C Resistor(1/16W 8.2K 1%) [R216,R219] AB B Transistor(DTA143ZUA) [Q16] AC B Transistor(DTC143ZUA) [Q1,Q4,Q6,Q8,Q11,Q12] AC B Transistor(DTC143ZUA) [Q15,Q18,Q22,Q24,Q25] AC B Transistor(DTC114EUA) [Q9,Q10,Q17,Q21,Q23] AC B Transistor(2SK3018) [Q2,Q5,Q7,Q19,Q20] AC B Transistor(2SB1197K) [Q13,Q14] AD B Transistor(2SD1898) [Q3] AC C Filter(ZJSR5101-102) [NF3,NF4,NF6,NF8] AB C Capacitor(50WV 3.3F) [C149] AA C Capacitor(50WV 0.010F) [C129] AC B LED(LT1D67A) [LED1] AC C Socket(8pin) [For IC4] AR C IC Socket(179707-1) [SOCKET1] AA B Diode(RLS73) [D5,D6,D30,D32,D34,D38] AA B Diode(RLS73) [D40] AD B Zener diode(RD22FB) [ZD1,ZD3] AF B IC(C24WC08L) [IC4] AR B IC(MTD1361-4101) [IC3] AH B IC(NJM7805A) [IC22] AD B IC(BD45271G) [IC15] AF B IC(TA7291S) [IC1,IC16] AG B IC(TD620003AP1) [IC2,IC26] AA C Resistor(1/8W 100 5%) [R231,R230] AA C Resistor(1/8W 1.2K 5%) [R8,R9,R13,R14] AA C Resistor(1/8W 150 5%) [R50,R54,R58] AA C Resistor(1/8W 1.5K 5%) [R209] AA C Resistor(1/8W 4.7K 5%) [R277] AA C Resistor(1/8W 390 5%) [R279,R280,R281] AC C Resistor(1W 240 5%) [R226] AB C Resistor(2W 1.0 5%) [R42,R43] AE C Connector(9pin) [CN17] AF C Connector(30pin) [CN12] AF C Connector(24pin) [CN13] AG C Connector(32pin) [CN4] AG C Connector(22pin) [CN11] AH C Connector(24pin) [CN10] AF C Connector(32pin) [CN16] AC C Connector(8pin) [CN21] AB C Connector(2pin) [CN7,CN22,CN23] AB C Connector(8pin) [CN5] AC C Connector(11pin) [CN8] AD C Connector(16pin) [CN14] AC C Connector(8pin) [CN9] AC C Connector(8pin) [CN6] AC C Connector(14pin) [CN15] AK C Connector(30pin) [CN2] AE C Connector(24pin) [CN3] AG B Crystal(AT-51 19.6608MHz) [X1] AP B Crystal(31.554MHz) [Except AR-M451N/U,AR-M455N/U][X2] AP B Crystal(31.554MHz) [AR-M451N/U,AR-M455N/U][X2] BX BX BX BX BV CA E E E E E E PCU PCU PCU PCU PCU PCU PWB PWB PWB PWB PWB PWB [AR-355N/U,AR-M351N/U](100V [AR-355N/U,AR-M351N/U](100V [AR-M455N/U,AR-M451N/U](100V [AR-M455N/U,AR-M451N/U](100V [AR-M351N/U](200V [AR-M351N/U](200V Series) Series) Series) Series) Series) Series)
TR No.
Effective time
1 1 1
N N N
901
23-2
Update : 06/02/27
S PCU PWB
NO.
901
PARTS CODE
CPWBX1637DS64 CPWBX1637FCF4
Inter- PRICE NEW PART change RANK MARK RANK BV E PCU PWB 1 CA N E PCU PWB
DESCRIPTION
[AR-M451N/U](200V Series) [AR-M451N/U](200V Series)
TR No.
manuals4you.com
23-3
4 5 6 7 8 9 10 11 12 14 15 16 17 18 19 20
21
22
24-1
22
23 24 25 26 27
28
29 30 31 32
33
34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61
! !
manuals4you.com
24-2
PARTS CODE
VHIHI207ECB0C VHIPT598DLF-1 VHIHG73C95V-1 VHI237R33LF-1 VHI23WAT255-1 VHI87R1060E-1 VHDF1071MT+0C VHIMRUP01++-1 RCNVD0003FCZZ VHIPM22G75+-1 VHIPM2060G+-1 VHILCX244MT0C VHILCX244MT0C VHILCX245MT0C VHILCX245MT0C VHILCX245MT0C VHILCX373MT0C VHIPT598ILF-1 VHILCX157MT0C VHI65345Y020C QPIN-0003GCPZ PCAPH0010GCZZ QJUM-0002FCZZ RFILN0048FCPZ RFILN0048FCPZ RCILF0115FCZZ RFILN0304FCPZ RFILN0305FCPZ RFILN0051FCZZ RFILN0051FCZZ RFILN0051FCZZ RFILN0051FCZZ RFILN0055FCZZ RFILN0056FCZZ RFILN0056FCZZ VHVICPS1.2/-1 VSDTC114EUA-1 VSDTC114YUA-1 VSUPA502TA+-1 VS2SC2412K/-1 VS2SB1198K/-1 VSDTA114EUA-1 VSTPC6108F+-1 VSTPC6004F+-1 VSDTA143ZUA-1 VS2SK3018++-1 VHV1608C2701C VHV1608C2701C VHV1608C2701C VHV1608C2701C VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD220J VRS-CZ1JD220J VRS-CZ1JD220J VRS-CZ1JD220J VRS-CZ1JD220J
103
104
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AN B RS232Driver IC(HIN207ECB-T) [IC42] AE B Reset IC(PST598DN(LF)) [IC47,IC48] AY B ASIC2(HG73C095TEV) [IC53] AF B IC(NJM2370R33) [IC54] AU B 2Mbit SRAM(N02L163WC2AT2-55I) [IC55] BQ B IC(MB87R1060V94 E1) [IC700] AH B Diode(74F1071MTCX_NL) [IC701] BF B IC(MRUP01 V2) [IC703] AY B DC-DC Converter(MPD4S008S(LF)) [IC718] BH B CODEC IC(PM-22/75(LF)) [IC723,IC721] BK B RET IC(PM2060i(LF)) [IC725] AE B Logic IC(74LCX244MTCX_NL) [IC726,IC729,IC732,IC742] AE B Logic IC(74LCX244MTCX_NL) [IC743,IC744,IC745] AE B Logic IC(74LCX245MTCX_NL) [IC727,IC728,IC730,IC731] AE B Logic IC(74LCX245MTCX_NL) [IC734,IC736,IC738,IC739] AE B Logic IC(74LCX245MTCX_NL) [IC740,IC741] AE B Logic IC(74LCX373MTCX_NL) [IC733,IC735,IC737] AE B Reset IC(PST598IN(LF)) [IC753] AE B Logic IC(74LCX157MTCX_NL) [IC755] BC B IC(UPD65345GJ-Y02-UEN-A) [IC756] AC C Pin(T3B-SQ(LF)) [JP6] AD C Cap(JM-2W-96) [JP6] AA C Taping jumper wire(JUMPER,VIDCLK) [JP19] AB C Filter(BLM15BB121SN1D(LF)) [L2,L3,L724,L749] AB C Filter(BLM15BB121SN1D(LF)) [L750,L755] AG C Choke Coil(DLW31SN900SQ2) [L700] AC C EMI Filter(DSS6NZ82A103Q55B(LF)) [L701,L703,L705,L753,L754] AC C Filter(BL02RN2R1P1A(LF)) [L702,L704,L706] AC C Filter(MMZ1608D121BTA00) [L714,L715,L716,L717,L718] AC C Filter(MMZ1608D121BTA00) [L719,L720,L721,L737,L738] AC C Filter(MMZ1608D121BTA00) [L739,L740,L741,L742,L743] AC C Filter(MMZ1608D121BTA00) [L744] AB C Filter(BLM21AG121SN1D) [L722] AA C Filter(BLM18AG151SN1D) [L725,L728,L729,L745,L746] AA C Filter(BLM18AG151SN1D) [L747] AF B IC protector(ICPS1.2) [Q1,Q28] AC B Transistor(DTC114EUA) [Q3,Q11,Q13,Q21,Q24,Q25,Q26] AB B Transistor(DTC114YUA) [Q4,Q12,Q15,Q27] AD B Transistor(UPA502T(LF)) [Q5,Q6,Q7] AB B Transistor(2SC2412K) [Q18,Q8] AC B Transistor(2SB1198K) [Q17,Q9] AC B Transistor(DTA114EUA) [Q10,Q14,Q20] AE B Transistor(TPC6108) [Q16] AE B Transistor(TPC6004 (TE85L,F)) [Q19] AB B Transistor(DTA143ZUA FT106) [Q22] AC B Transistor(2SK3018) [Q23] AC B Varistor(AVR-M1608C270KT2AB) [RV12,RV13,RV14,RV15,RV16] AC B Varistor(AVR-M1608C270KT2AB) [RV17,RV18,RV19,RV20,RV21] AC B Varistor(AVR-M1608C270KT2AB) [RV22,RV23,RV24,RV25,RV26] AC B Varistor(AVR-M1608C270KT2AB) [RV27] AA C Resistor(1/16W 10K 5%) [R12,R13,R15,R16,R18,R44] AA C Resistor(1/16W 10K 5%) [R45,R60,R61,R62,R70,R72] AA C Resistor(1/16W 10K 5%) [R86,R91,R93,R123,R131] AA C Resistor(1/16W 10K 5%) [R158,R159,R160,R163,R165] AA C Resistor(1/16W 10K 5%) [R167,R168,R203,R208,R213] AA C Resistor(1/16W 10K 5%) [R216,R217,R230,R237,R238] AA C Resistor(1/16W 10K 5%) [R239,R240,R241,R242,R245] AA C Resistor(1/16W 10K 5%) [R246,R249,R254,R259,R260] AA C Resistor(1/16W 10K 5%) [R261,R263,R264,R267,R269] AA C Resistor(1/16W 10K 5%) [R271,R272,R273,R274,R282] AA C Resistor(1/16W 10K 5%) [R283,R284,R285,R429,R430] AA C Resistor(1/16W 10K 5%) [R480,R494,R795,R796,R805] AA C Resistor(1/16W 10K 5%) [R824,R833,R839] AA C Resistor(1/16W 10K 5%) [R845,R859,R947,R949,R974] AA C Resistor(1/16W 10K 5%) [,R976,R977,R978,R981] AA C Resistor(1/16W 10K 5%) [R1016,R1070,R1120,R1121] AA C Resistor(1/16W 10K 5%) [R1122,R1130,R1131] AA C Resistor(1/16W 10K 5%) [R1132,R1133,R1134,R1135] AA C Resistor(1/16W 10K 5%) [R1167,R1168,R1174,R1204] AA C Resistor(1/16W 10K 5%) [R1226,R1246,R1248,R1249] AA C Resistor(1/16W 10K 5%) [R1250,R1260,R1283,R1286] AA C Resistor(1/16W 10K 5%) [R1294,R1296] AA C Resistor(1/16W 22 5%) [R14,R17,R19,R24,R27,R30] AA C Resistor(1/16W 22 5%) [R31,R34,R35,R37,R39,R40] AA C Resistor(1/16W 22 5%) [R43,R46,R51,R54,R57,R814] AA C Resistor(1/16W 22 5%) [R815,R816,R817,R1022] AA C Resistor(1/16W 22 5%) [R1273]
TR No.
Effective time
24-3
105
106
107
108
112
113
manuals4you.com
24-4
PARTS CODE
VRS-CZ1JD511J VRS-CZ1JD361F VRS-CZ1JD561F VRS-CZ1JD820J VRS-CZ1JD221J VRS-CZ1JD105J VRS-CZ1JD622J VRS-CZ1JD562F VRS-CZ1JD472F VRS-CZ1JD563J VRS-CZ1JD562J VRS-TX2HD000J VRS-TX2HD000J VRS-CZ1JD471J VRS-CZ1JD474J VRS-CZ1JD152F VRS-CY1JD000J VRS-CY1JD000J VRS-CY1JD000J VRS-CY1JD000J QSW-S0545FCPZ RCRUA0024FCPZ RCRUA0008FCPZ RCRUA0002QSPZ RCRUA0007FCPZ RCRUA0023FCPZ RCRSA0085FCPZ RCRUA0005FCPZ RCRUA0027FCPZ RCRSC0082FCPZ RCRUA0009FCPZ
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AA C Resistor(1/16W 510 5%) [R278] AA C Resistor(1/16W 360 1%) [R417] AA C Resistor(1/16W 560 1%) [R418] AA C Resistor(1/16W 82 5%) [R541,R544,R546] AA C Resistor(1/16W 220 5%) [R797] AA C Resistor(1/16W 1.0M 5%) [R798] AA C Resistor(1/16W 6.2K 5%) [R804] AA C Resistor(1/16W 5.6K 1%) [R950] AA C Resistor(1/16W 4.7K 1%) [R951] AA C Resistor(1/16W 56K 5%) [R1090,R1091] AA C Resistor(1/16W 5.6K 5%) [R1261,R1229] AB C Resistor(1/2W 0 5%) [R1242,R1243,R1359,R1360] AB C Resistor(1/2W 0 5%) [R1361] AA C Resistor(1/16W 470 5%) [R1272] AA C Resistor(1/16W 470K 5%) [R1281] AA C Resistor(1/16W 1.5K 1%) [R1285] AA C Resistor(1/16W 0 5%) [R1364,R1365,R1366,R1367] AA C Resistor(1/16W 0 5%) [R1368,R1369,R1370,R1371] AA C Resistor(1/16W 0 5%) [R1372,R1373,R1374,R1375] AA C Resistor(1/16W 0 5%) [R1376,R1377,R1378,R1379] AM B DIP switch(OTAX KSP02(LF)) [SW2] AL B Crystal(SG-8002JC 66.0MHz(LF)) [X1] AL B Crystal(SG-8002JC 40.57MHz(LF)) [X2] AL B Crystal(SG-8002JC 33.33333MHz(LF)) [X3] AL B Crystal(SG-8002JC 31.554MHz(LF)) [X4] AL B Crystal(SG-8002JC 64.0M) [X5] AE B Crystal(DT-38 32.768K(LF)) [X6] AL B Crystal(SG-8002JC 14.7456M(LF)) [X7] AL B Crystal(SG-8002JC 74.9M(LF)) [X700] AH B Crystal(MA-406 24MHz(LF)) [X701] AL B Crystal(SG-8002JC 66.666MHz(LF)) [X703]
TR No.
Effective time
24-5
U Fuse PWB
NO.
1 ! ! 2 3 4 5 6 7 8 901
PARTS CODE
QCNCM0895FCZZ QFS-B3631QCPZ QFS-D1421QCPZ QFSHB0028FCZZ QTANP0215FCZZ QTANP0218FCPZ QSPGC0001FCZZ VHV10V471K+-1 DHAI-3252FCZ1 (Unit) CPWBF1626FCE1 CPWBF1627FCE2
Inter- PRICE NEW PART change RANK MARK RANK AG C Connector(3pin) AH A Fuse(15A 250V) AE A Fuse(10A 240V) AC C Fuse holder(00335-31) AC C Terminal(85163) AC C Terminal(TP00370-21) AK B Surge absorber(2700V) AD B Varistor(10V471K) AE C DH harness AU AW E E Fuse PWB Fuse PWB
DESCRIPTION
[CN1] (100V Series)[F1] (200V Series)[F1,2] [F1,2] [Lout,LFAX,Nout,NFAX] [FG] (100V Series)[A1] [VR1]
TR No.
Effective time
manuals4you.com
25-1
Update : 06/02/27
V Relay PWB
NO.
1 2 3 4 5 6 7 8 9 10 11 12 13
PARTS CODE
RRLYD2112QCZZ VHDDSM1D1//-1 VHD10JDA10+-1 VS2SD1768S+-1 VRD-HT2EY471J VRD-HT2EY272J VCEAZA1VW476M QCNCM0672FCZZ QCNCM1178FCZZ QCNCM7014SC0C QTANP0215FCZZ QFS-E1312QCZZ QFSHB0028FCZZ VHV10V271K+-1 VHV10V471K+-1 (Unit) CPWBF1629FCE1 CPWBF1629FCE2
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AL B Relay(ALE15B12) AB B Diode(DSM1D1) 1 AB B Diode(10JDA10) AR B Transistor(2SD1768) AA C Resistor(1/4W 470 5%) AA C Resistor(1/4W 2.7K 5%) AC C Capacitor(35WV 47F) AB C Connector(2pin) AC C Connector(2pin) AA C Connector(3pin) AC C Terminal(85163) AD A Fuse(T2.5AH250V) AC C Fuse holder(TP00351-31) AD B Varistor(10V271K) AD B Varistor(10V471K) AY AY E E Relay PWB Relay PWB
TR No. [RY1,RY2] [D1] [D1] [Q1] [R1] [R2] [C1] [CN1] [CN2] [CN3] [Lin,Nin,Lout,Nout] [F1] [(F1)] (100V Series)[VR1] (200V Series)[VR1] (100V Series) (200V Series)
Effective time
06/05
901
26-1
PARTS CODE
0AV1570000002 0AV1570000003 0AV1570000004 0AV1650000064 0AV1570000006 0AV1390000260 0AV1690000133
7 0AV1690000133 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 0AV1610000091 0AV1390000261 0AV1390000262 0AV1690000113 0AV1480000084 0AV1690000134 0AV1690000138 0AV1610000109 0AV1390000263 0AV1390000264 0AV1390000265 0AV1390000266 0AV1390000136 0AV1390000267 0AV1390000268 0AV1690000137 0AV1390000269 0AV1390000270 0AV1480000107 0AV1390000271 0AV3060035000 0AV3070123000 0AV3060031000 0AV3060040000 0AV3050019000 0AV3050019000 0AV3050091000 0AV3050091000 0AV3050091000 0AV3070085000 0AV3070056000 0AV3070013000 0AV3050087000 0AV3070061000 0AV3050070000 0AV3050080000 0AV3070081000 0AV3070069000 0AV3070014800 0AV3070112000 0AV3070023000 0AV3070049000 0AV3070156000 0AV3050104000 0AV3090079000 0AV3090041000 0AV3090008000 0AV4070063000 0AV4070064000 0AV4120013000 0AV4050016000 0AV4120008000 0AV4080011400 0AV4120002000 0AV4050010000 0AV3080421300 0AV3180000009 0AV3042698000 0AV3001015500 0AV3042543000 0AV3021815500 0AV3021815500
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AD C FILM CAPACITOR(LE104-L 0.1F,250V(LE)) [C701] AD C FILM CAPACITOR(LE104-C 0.1F,250V(LE)) [C760,C761] AN C FILM CAPACITOR(LE155-C 1.5F,250V(LE)) [C702] AD C CERAMIC CAPACITOR(DE1307E472M-KH 4700pF(KH)) [C703,C704] AF C FILM CAPACITOR(LE474-C 0.47F,250V(LE)) [C705] AL-ELECTROLYTIC CAPACITOR (LGU2D182MELC 1800mF 200V) AY C [C706] CERAMIC CAPACITOR(PRE132R104K50 0.1F,50V) AC C [C707,C718,C720,C730,C733,C742] CERAMIC CAPACITOR(PRE132R104K50 0.1F,50V) AC C [C752,C756,C759,C765] CERAMIC CAPACITOR(DE0905-979R102K1K 1000pF,1KV) AC C [C708,C709,C710,C726,C747,C748,C749] AC C AL-ELECTROLYTIC CAPACITOR(UPJ1H4R7MDD 4.7F,50V) [C711] AL-ELECTROLYTIC CAPACITOR(UPJ1H220MED 22F,50V) AC C [C712,C766,C768] AE C CERAMIC CAPACITOR(DE1610-2E472M-KX 4700pF(KX)) [C713,C767] AD C FILM CAPACITOR(CQMY-92MC2A104J 0.1F,100V) [C714,C715] CERAMIC CAPACITOR(RPE132R103K50 0.01F,50V) AC C [C716,C717,C763] AC C CERAMIC CAPACITOR(RPE132R472K50 4700pF,50V) [C719,C757] AC C CERAMIC CAPACITOR(DE0705-979R471K1K 470pF,1KV) [C721,C722] AL-ELECTROLYTIC CAPACITOR(UPJ1V182MHD6 1800F,35V) AC C [C728,C729] AC C AL-ELECTROLYTIC CAPACITOR(UPJ1H010MDD 1F,50V) [C734,C771] AC C AL-ELECTROLYTIC CAPACITOR(UHD1V681MHD 680F,35V) [C735] AG C AL-ELECTROLYTIC CAPACITOR(UHD1V102MHD 1000F,35V) [C738] CERAMIC CAPACITOR(RPE132R223K50 0.022F,50V) AF C [C739,C744,C746,C755] AL-ELECTROLYTIC CAPACITOR(UPJ1H2R2MDD 2.2F,50V) AC C [C740,C753] AC C AL-ELECTROLYTIC CAPACITOR(UHD1C222MHD 2200F,16V) [C741] CERAMIC CAPACITOR(RPE132R102K50 1000pF,50V) AC C [C743,C745,C770] AL-ELECTROLYTIC CAPACITOR(UHD1A562MHD 5600F,10V) AK C [C750,C751] AD C AL-ELECTROLYTIC CAPACITOR(UPJ1V820MED 82F,35V) [C754] AE C FILM CAPACITOR(ECQE2104RJF 0.1F,400V) [C764] AC C AL-ELECTROLYTIC CAPACITOR(UPJ1C101MED 100F,16V) [C772] AE B DIODE(S1WB(A)60 1A,600V) [D701] AC B ZENER DIODE(RD6.8ES 400mW) [D702] AC B DIODE(ERA15-04 1A,400V) [D703,D704,D748,D763] AR B DIODE(D15XB60 15A,600V) [D705] AF B DIODE(ERA91-02 0.5A,200V) [D706,D708,D710,D717,D746] AF B DIODE(ERA91-02 0.5A,200V) [D747,D755,D758,D759] AB B DIODE(1SS270 60V,150mA) [D707,D714,D726,D727,D728] AB B DIODE(1SS270 60V,150mA) [D731,D733,D738,D743,D744] AB B DIODE(1SS270 60V,150mA) [D751,D752,D754,D760,D762] AC B ZENER DIODE(RD33ES 400mW) [D709,D712,D756] AD B ZENER DIODE(RD20ES 400mW) [D716] AB B ZENER DIODE(RD5.6ES 400mW) [D715,D720,D734,D736,D739] AN B DIODE(YG906C2R 20A,200V) [D721] AC B ZENER DIODE(RD4.7ES 400mW) [D724] AK B DIODE(YG802C06 10A,60V) [D729] AP B DIODE(YG805C04 20A,40V) [D730] AC B ZENER DIODE(RD3.9ES 400mW) [D732] AC B ZENER DIODE(RD51E 500mW) [D735] AC B ZENER DIODE(RD10ES 400mW) [D742,D749] AC B ZENER DIODE(RD3.0ES 400mW) [D745,D753] AE B ZENER DIODE(RD24ES 400mW) [D713,D757] AB B ZENER DIODE(RD27ES 400mW) [D761] AC B ZENER DIODE(RD4.3ES 400mW) [D765] AD B DIODE(AK04) [D750,D764] AL B IC(FA5515P) [IC701,IC705] AF B IC(UPC1093J-1) [IC702,IC704] AK B IC(MB3759P) [IC703] AR C INDUCTOR(DRC31-15A202) [L701] AL C INDUCTOR(DRB25-05A202) [L702] AC C INDUCTOR(T314OP3206536HW) [L703,L710,L715] AG C INDUCTOR(PC8T8R2M) [L707] AD C INDUCTOR(LFP3A) [L708] AL C INDUCTOR(HK-10S100-4500S) [L709] AC C INDUCTOR(B-01-A) [L711,L713,L714] AH C INDUCTOR(PC8T3R3M) [L712] AE B PHOTO COUPLER(PS2561A) [PC701,PC703,PC704,PC706] AL B PHOTO TRIAC COUPLER(PC3SF11YV) [PC702,PC705] AS B FET(2SK2698 500V,15A) [Q701] AC B TRANSISTOR(2SA1015 -50V,-150mA) [Q702,Q713] AQ B FET(2SK2543 500V,8A) [Q704] AC B TRANSISTOR(2SC1815 50V 150mA) [Q706,Q709,Q710,Q711,Q714] AC B TRANSISTOR(2SC1815 50V 150mA) [Q715,Q717,Q718,Q719,Q723]
TR No.
Effective time
manuals4you.com
27-1
PARTS CODE
0AV3040504000 0AV3022655500 0AV3042736000 0AV3021002999 0AV2022213040 0AV2054754077 0AV2014723030 0AV2012233010 0AV2011843030 0AV2990106000 0AV2011053010 0AV2011023010 0AV2051083055 0AV2014733020 0AV2011213030 0AV2011203020 0AV2011033010
Inter- PRICE NEW PART TR No. DESCRIPTION change RANK MARK RANK AN B FET(2SJ504) [Q707] AE B TRANSISTOR(2SC2655) [Q708] AN B FET(2SK2736) [Q712] AD B TRANSISTOR(RN1002) [Q720,Q721,Q722] AC C METAL OXIDE FILM RESISTOR(RSU01WST5A221J 220 1W) [R701] AF C CEMENT FILLED RESISTOR(MNS05WNZ4R7J 4.7 5W) [R702] FLAME PROOF CARBON RESISTOR(RDF50S4.7KJ 4.7K 1/2W) AB C [R703,R704,R705] FLAME PROOF CARBON RESISTOR(RDF16S22KJ 22K,1/6W) AA C [R706,R772,R827,R828] FLAME PROOF CARBON RESISTOR(RDF50S180KJ 180W 1/2W) AB C [R707] AC C METAL OXIDE FILM RESISTOR(RSMF1B273F 27K 1W) [R708,R709] AB C FLAME PROOF CARBON RESISTOR(RDF16S1MJ 1M 1/6W) [R710] FLAME PROOF CARBON RESISTOR(RDF16S1KJ 1K,1/6W) AA C [R711,R737,R750,R784,R817,R751] AE C CEMENT FILLED RESISTOR(BPR02WFTR10J 0.1 2W) [R739] FLAME PROOF CARBON RESISTOR(RDF25S47KJ 47K 1/4W) AB C [R713,R714] FLAME PROOF CARBON RESISTOR(RDF50S120J 120 1/2W) AB C [R715,R732,R726,R728] AB C FLAME PROOF CARBON RESISTOR(RDF25S12J 121/4W) [R716] FLAME PROOF CARBON RESISTOR(RDF16S10KJ 10K,1/6W) AA C [R717,R730,R735,R741,R753,R758] FLAME PROOF CARBON RESISTOR(RDF16S10KJ 10K,1/6W) AA C [R776,R795,R800,R818,R824,R825] METAL OXIDE FILM RESISTOR(RSS5FB100JH1 100 5W) AF C [R718,R744] FLAME PROOF CARBON RESISTOR(RDF16S3.3KJ 3.3KW 1/6W) AA C [R719,R775] AC C METAL OXIDE FILM RESISTOR(RSF1B120J 120 1W) [R720,R731] AA C METAL FILM RESISTOR(SN16S909D 909 1/6W) [R721] FLAME PROOF CARBON RESISTOR(RDF16S39KJ 39K,1/6W) AA C [R790] AC C METAL OXIDE FILM RESISTOR(RSS182J 82 1W) [R723] FLAME PROOF CARBON RESISTOR(RDF16S220KJ 220KW,1/6W) AA C [R724] AC B FUSING RESISTOR(RF25S100J 100 1/4W) [R725,R727] AE C CEMENT FILLED RESISTOR(BPR02WFTR10J 0.1 2W) [R712] FLAME PROOF CARBON RESISTOR(RDF16S2.2KJ 2.2K,1/6W) AA C [R749,R766,R777,R807,R808] FLAME PROOF CARBON RESISTOR(RDF16S2.2KWJ 2.2K,1/6W) AA C [R815,R810,R797] AA C FLAME PROOF CARBON RESISTOR(RDF16S180J 180,1/6W)[R768] AB C METAL FILM RESISTOR(SN16S68KD 68K,1/6W) [R736] AC B FUSING RESISTOR(RF16S120J 120 1/6W) [R738] AA C FLAME PROOF CARBON RESISTOR(RDF25S22J 22 1/4W) [R740] FLAME PROOF CARBON RESISTOR(RDF16S82KJ 82K,1/6W) AA C [R742] AF C METAL OXIDE FILM RESISTOR(RSS5FB47JH1 47 5W) [R743] FLAME PROOF CARBON RESISTOR(RDF25S33KJ 33K 1/4W) AA C [R746,R747] FLAME PROOF CARBON RESISTOR(RDF16S33KJ 33K 1/6W) AA C [R748] AA C METAL FILM RESISTOR(SN16S180D 180 1/6W) [R734] AC C METAL FILM RESISTOR(SN16S22.3KD 22.3K 1/6W) [R754] AC C METAL FILM RESISTOR(SN16S2.55KD 2.55K 1/6W) [R755] AA C FLAME PROOF CARBON RESISTOR(RDF16S15KJ 15K 1/6W)[R756] AA C FLAME PROOF CARBON RESISTOR(RDF25S220J 220 1/4W)[R761] AA C FLAME PROOF CARBON RESISTOR(RDF25S4.7J 4.7 1/4W) [R762] FLAME PROOF CARBON RESISTOR(RDF25S4.7KJ 4.7KW 1/4W) AA C [R763] AG C CEMENT FILLED RESISTOR(BPR05WFTR10J 0.01 5W) [R764] FLAME PROOF CARBON RESISTOR(RDF16S5.6KJ 5.6KW 1/6W) AA C [R765] AC B FUSING RESISTOR(RF16S100J 100 1/6W) [R767] FLAME PROOF CARBON RESISTOR(RDF25S120J 120 1/4W) AA C [R769,R771] FLAME PROOF CARBON RESISTOR(RDF16S12KJ 12K 1/6W) AA C [R773] AC C METAL FILM RESISTOR(SN16S1.2KD 1.2K 1/6W) [R778] AC C METAL FILM RESISTOR(SN16S39KD 39K 1/6W) [R779] AC C METAL OXIDE FILM RESISTOR(RSF1B22J 22 1W) [R780] AA C FLAME PROOF CARBON RESISTOR(RDF16S330J 330 1/6W)[R781] AA C FLAME PROOF CARBON RESISTOR(RDF16S100J 100 1/6W)[R782] AA C FLAME PROOF CARBON RESISTOR(RDF16S390J 390 1/6W)[R783] FLAME PROOF CARBON RESISTOR(RDF16S1.2KJ 1.2K 1/6W) AA C [R785] FLAME PROOF CARBON RESISTOR(RDF16S680J 680 1/6W) AA C [R786] FLAME PROOF CARBON RESISTOR(RDF16S120J 120 1/6W) AA C [R791]
Effective time
27-2
PARTS CODE
0AV2014713010 0AV2012733010 0AV2015633010 0AV2043313010 0AV2021233040 0AV2141803040 0AV2011043020 0AV2014733010 0AV2015633020 0AV2042203010 0AV2014723010 0AV2011043010 0AV2990104000 0AV2041003020 0AV2990107000 0AV2990112000 0AV2060025000 0AV4000136711 0AV4000131011 0AV3160033000 0AV3160037000 0AV2081029188 0AV5080013000 0AV5190002000 0AV5030126000 0AV5030127000 0AV5030128000 0AV5030129000 0AV5030149000 0AV5030088000 0AV5130009000 0AV5130011000 0AV8117730416 0AV8117730516 0AV8117730616 0AV6113116511 0AV6114150911 0AV6114150111 0AV5050005000 0AV7100003000 0AV5110012000 0AV5110012000 0AV5110012000 0AV5110012000 0AV5110003000 0AV5110003000 0AV5110001000 0AV5110001000 0AV5110006000 0AV5110006000 0AV5110006000 0AV5110002000 0AV5110011000 0AV5110004000 0AV5110004000 0AV5110004000 0AV5110004000 0AV5060176000 0AV5060177000 0AV5060018000 0AV5060089000 (Unit) RDENC0036FCZ3
DESCRIPTION
FLAME PROOF CARBON RESISTOR(RDF16S470J) [R792,R814,R809,R826] FLAME PROOF CARBON RESISTOR(RDF16S27KJ) [R793,R794] FLAME PROOF CARBON RESISTOR(RDF16S56KJ) [R798] FUSING RESISTOR(RF16S330J) [R801] METAL OXIDE FILM RESISTOR(RSF1B12KJ) [R804,R805] METAL OXIDE FILM RESISTOR(RSMF1B18J) [R806] FLAME PROOF CARBON RESISTOR(RDF25S100KJ) [R811,R812] FLAME PROOF CARBON RESISTOR(RDF16S47KJ)[R813,R819,R820] FLAME PROOF CARBON RESISTOR(RDF25S56KJ) [R733] FUSING RESISTOR(RF16S22J) [R816] FLAME PROOF CARBON RESISTOR(RDF16S4.7KJ) [R821,R822,R752,R759,R774,R799] FLAME PROOF CARBON RESISTOR(RDF16S100KJ) [R823] METAL FILM RESISTOR(SN16S56KD) [R745] FUSING RESISTOR(RF25S10J) [R829] METAL FILM RESISTOR(SN16S1.5KD) [R729] METAL FILM RESISTOR(SN16S49.9KD) [R722] TEMP.FUSING RESISTOR(MEG05N4R7KB142) [FR701] Transformer(N-T01-367) [T701] Transformer(N-T01-310) [T702] Traic(TM1641P) [TR701,TR703] Traic(BCR10PM-12LP) [TR702] POTENTIOMETER(RH063MC13R) [VR701,VR702] RELAY(OMIH-SS-124LM) [RL701] Varistor(ENC271D-10A-TA-B) [X701] Connector(B03P-VL) [CN1] Connector(B7B-PH-K-S) [CN2] Connector(B03B-XASK-1) [CN4] Connector(B12P-HL-A) [CN5] Connector(B5P-VH) [CN6] Connector(B2P-VH) [CN7] TERMINAL(TP82224-31) TERMINAL(TP00370-21) SCREW(NACPEW-B3X8SF) SCREW(NACPEW-B3X10SF) SCREW(NACPEW-B3X12SF) HEATSINK(LM31165) HEATSINK(LM41509) HEATSINK(LM41510) HOLDER(PFC5000-0203) INSULATION SHEET(M-30AD-D-3) Jumper wire(RJ-SKA-06) [RJ701,RJ702,RJ703,RJ708,RJ712] Jumper wire(RJ-SKA-06) [RJ713,RJ721,RJ727,RJ730,RJ735] Jumper wire(RJ-SKA-06) [RJ746,RJ760,RJ768,RJ769,RJ771] Jumper wire(RJ-SKA-06) [RJ772,RJ773,RJ775,RJ776] Jumper wire(RJ-SBA-06) [RJ707,RJ722,RJ723,RJ731,RJ736] Jumper wire(RJ-SBA-06) [RJ738,RJ739,RJ743,RJ748,RJ778] Jumper wire(RJ-SCA-06) [RJ711,RJ714,RJ716,RJ747,RJ756] Jumper wire(RJ-SCA-06) [RJ757,RJ759,RJ770,RJ779] Jumper wire(RJ-SDA-06) [RJ715,RJ718,RJ725,RJ726] Jumper wire(RJ-SDA-06) [RJ742,RJ745,RJ752,RJ754] Jumper wire(RJ-SDA-06) [RJ758,RJ763,RJ766,RJ774,RJ777] Jumper wire(RJ-SEA-06) [RJ704,RJ728,RJ733,RJ734,RJ753] Jumper wire(RJ-SFA-06) [RJ717,RJ729,RJ740,RJ741,RJ765] Jumper wire(RJ-SGA-06) [RJ705,RJ706,RJ709,RJ710,RJ719] Jumper wire(RJ-SGA-06) [RJ720,RJ724,RJ732,RJ737] Jumper wire(RJ-SGA-06) [RJ749,RJ750,RJ751,RJ755] Jumper wire(RJ-SGA-06) [RJ761,RJ762,RJ764,RJ767] FUSE(23706.3) [F701,F702,F704] FUSE(23704) [F703] FUSE(23710) [F706] FUSE(396 2) [F705] AC/DC power supply PWB 100
TR No.
Effective time
163 164 165 166 167 168 ! ! ! ! 169 170 171 172
! 901
manuals4you.com
27-3
PARTS CODE
0AV1560000009 0AV1560000002 0AV1560000008 0AV1690000074 0AV1560000005 0AV1390000260 0AV1690000133 0AV1690000133 0AV1610000091 0AV1610000091 0AV1390000261 0AV1390000162 0AV1690000113 0AV1480000109 0AV1690000134 0AV1690000138 0AV1610000109 0AV1390000263 0AV1390000264 0AV1390000265 0AV1390000266 0AV1690000136 0AV1390000267 0AV1390000268 0AV1690000137 0AV1390000269 0AV1390000270 0AV1480000107 0AV1390000271 0AV3060035000 0AV3070123000 0AV3060031000 0AV3060040000 0AV3050019000 0AV3050019000 0AV3050086000 0AV3050086000 0AV3050086000 0AV3070128000 0AV3070115000 0AV3070119000 0AV3050087000 0AV3070132000 0AV3050070000 0AV3050080000 0AV3070124000 0AV3070125000 0AV3070126000 0AV3070130000 0AV3070127000 0AV3050104000 0AV3070141000 0AV2060025000 0AV3090079000 0AV3090041000 0AV3090003000 0AV4070063000 0AV4070064000 0AV4120013000 0AV4050016000 0AV4120008000 0AV4080014000 0AV4120002000 0AV4050010000 0AV3082561300 0AV3180000009 0AV3042698000 0AV3001015500 0AV3042543000 0AV3021815500 0AV3021815500 0AV3040504000 0AV3022655500 0AV3042736000 0AV3021002999 0AV2022213040 0AV2054754077 0AV2014723030
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AE C Film capacitor(RE104-L 0.1F 250V(RE)) [C701] AD C Film capacitor(RE104-C 0.1F 250V(RE)) [C760,C761] AR C Film capacitor(RE155-C 1.5F 250V(RE)) [C702] AD C Ceramic capacitor(DE0807E102M-KH 1000PF(KH)) [C703,C704] AH C Film capacitor(RE474-C 0.47F 250V(RE)) [C705] AY C AL-ELECTROLYTIC CAPACITOR(1800F 200V) [C706] AC C CERAMIC CAPACITOR(0.1F 50V) [C707,C718,C720,C730,C733] AC C CERAMIC CAPACITOR(0.1F 50V) [C742,C752,C756,C759,C765] Ceramic capacitor(DE0905-979R102K1K 1000PF 1KV) AC C [C708,C709,C710,C726,C747] AC C Ceramic capacitor(DE0905-979R102K1K 1000PF 1KV) [C748,C749] AC C AL-ELECTROLYTIC CAPACITOR(4.7F 50V) [C711] AD C AL-ELECTROLYTIC CAPACITOR(22F 50V) [C712,C766,C768] AE C Ceramic capacitor(DE1610-2E472M-KX 4700PF(KX)) [C713,C767] AD C FILM CAPACITOR(0.1F 50V) [C714,C715] AC C CERAMIC CAPACITOR(0.01F 50V) [C716,C717,C763] AC C CERAMIC CAPACITOR(4700PF 50V) [C719,C757] AC C Ceramic capacitor(DE0705-979R471K1K 470PF 1KV) [C721,C722] AC C AL-ELECTROLYTIC CAPACITOR(1800F 35V) [C728,C729] AC C AL-ELECTROLYTIC CAPACITOR(1F 50V) [C734,C771] AC C AL-ELECTROLYTIC CAPACITOR(680F 35V) [C735] AG C AL-ELECTROLYTIC CAPACITOR(1000F 35V) [C738] AD C CERAMIC CAPACITOR(0.022F 50V) [C739,C744,C746,C755] AC C AL-ELECTROLYTIC CAPACITOR(2.2F 50V) [C740,C753] AC C AL-ELECTROLYTIC CAPACITOR(2200F 16V) [C741] AC C CERAMIC CAPACITOR(1000PF 50V) [C743,C745,C770] AK C AL-ELECTROLYTIC CAPACITOR(5600F 10V) [C750,C751] AD C AL-ELECTROLYTIC CAPACITOR(82F 35V) [C754] AE C FILM CAPACITOR(0.1F 400V) [C764] AC C AL-ELECTROLYTIC CAPACITOR(100F 16V) [C772] AE B Diode(S1WB(A)60 1A 600V) [D701] AC B Zenner diode(RD6.8ES 400mw) [D702] AC B Diode(ERA15-04 1A 400V) [D703,D704,D748,D763] AR B Diode(D15XB60 15A 600V) [D705] AF B Diode(ERA91-02 0.5A 200V) [D706,D708,D710,D717,D746] AF B Diode(ERA91-02 0.5A 200V) [D747,D755,D758,D759] AB B Diode(1SS270A 0.15A 60V) [D707,D714,D726,D727,D728] AB B Diode(1SS270A 0.15A 60V) [D731,D733,D737,D738,D743] AB B Diode(1SS270A 0.15A 60V) [D744,D751,D752,D754,D760,D762] AC B Zenner diode(RD33ES 400mW) [D709,D712,D756] AC B Zenner diode(RD20ES 400mW) [D716] AC B Zenner diode(RD5.6ES 400mW) [D715,D720,D734,D736,D739] AN B Diode(YG906C2R 20A 200V) [D721] AC B Zenner diode(RD4.7ES 400mW) [D724] AK B Diode(YG802C06 10A 60V) [D729] AP B Diode(YG805C04 20A 40V) [D730] AC B Zenner diode(RD3.9ES 400mW) [D732] AC B Zenner diode(RD10ES 400mW) [D742,D749] AC B Zenner diode(RD3.0ES 400mW) [D745,D753] AC B ZENNER DIODE(400mW) [D757,D713] AC B Zenner diode(RD27ES 400mW) [D761] AD B DIODE(1A 40V) [D750,D764] AC B ZENNER DIODE(400mW) [D765] AK C TEMP.FUSING RESISTOR(4.75W 142C) [FR701] AL B IC(FA5515P) [IC701,IC705] AF B IC(UPC1093J-1) [IC702,IC704] AM B IC(MB3759P) [IC703] AR C Inductor(DRC31-15A202) [L701] AL C Inductor(DRB25-05A202) [L702] AC C Inductor(T314OP3206536HW) [L703,L710,L715] AG C Inductor(PC8T8R2M) [L707] AD C Inductor(LFP3A) [L708] AL C Inductor [L709] AC C Inductor(B-01-A) [L711,L713,L714] AH C Inductor(PC8T3R3M) [L712] AF B Photo coupler(PS2561) [PC701,PC703,PC704,PC706,PC707] AL B PHOTO TRIAC COUPLER [PC702,PC705] AS B FET(2SK2698 500V 15A) [Q701] AC B Transistor(2SA1015 -50V -150mA) [Q702,Q713] AQ B FET(2SK2543 500V 8A) [Q704] AC B Transistor(2SC1815 50V 150mA) [Q706,Q709,Q710,Q711,Q714] AC B Transistor(2SC1815 50V 150mA) [Q715,Q717,Q718,Q719,Q723] AN B FET(2SJ504) [Q707] AE B Transistor(2SC2655) [Q708] AN B FET(2SK2736) [Q712] AD B Transistor(RN1002) [Q720,Q721,Q722] AC C Metal oxide film resistor(RSU01WST5A221J 220 1W) [R701] AF C Cement filled resistor(MNS05WNZ4R7J 4.7 5W) [R702] Flame proof carbon resistor(RDF50S4.7KJ 4.7K 1/2W) AB C [R703,R704,R705]
TR No.
Effective time
28-1
PARTS CODE
0AV2012233010 0AV2011843030 0AV2990106000 0AV2011053010 0AV2011023010 0AV2051083055 0AV2014733020 0AV2011213030 0AV2011203020 0AV2011033010
DESCRIPTION
Flame proof carbon resistor(RDF16S22KJ 22K 1/6W) [R706,R772,R827,R828] Flame proof carbon resistor (RDF50S180KJ 180K 1/2W) [R707] METAL OXIDE FILM RESISTOR(27K1W) [R708,R709] Flame proof carbon resistor(RDF16S1MJ 1M 1/6W) [R710] Flame proof carbon resistor(RDF16S1KJ 1K 1/6W) [R711,R737,R750,R784,R817] Cement filled resistor(BPR02WFTR10J 0.1 2W) [R712,R739] Flame proof carbon resistor(RDF25S47KJ 47K 1/4W) [R713,R714] Flame proof carbon resistor(RDF50S120J 120 1/2W) [R715,R732,R726,R728] Flame proof carbon resistor(RDF25S12J 12 1/4W) [R716] Flame proof carbon resistor(RDF16S10KJ 10K 1/6W) [R717,R730,R735,R741,R753] Flame proof carbon resistor(RDF16S10KJ 10K 1/6W) [R758,R776,R795,R800,R818] Flame proof carbon resistor(RDF16S10KJ 10K 1/6W) [R824,R825] Metal oxide film resistor(RSS5FB100J H1 100 5W) [R718,R744] Flame proof carbon resistor(RDF16S3.3KJ 3.3K 1/6W) [R719,R775] METAL OXIDE FILM RESISTOR(1201W) [R720,R731] Fusing resistor(RF16S820J 820 1/6W) [R721] Flame proof carbon resistor(RDF16S39KJ 39K 1/6W) [R790] Metal oxide film resistor(RSS182J 82 1W) [R723] Flame proof carbon resistor(RDF16S220KJ 220K 1/6W) [R724] Fusing resistor(RF50S100J 100 1/2WH) [R725,R727] Flame proof carbon resistor(RDF16S2.2KJ 2.2K 1/6W) [R749,R766,R777,R807,R808] Flame proof carbon resistor(RDF16S2.2KJ 2.2K 1/6W) [R815,R810,R797] Flame proof carbon resistor(RDF16S180J 180 1/6W) [R734,R768] METAL FILM RESISTOR(68K 1/6W) [R736] Fusing resistor(RF16S120J 120 1/6W) [R738] Flame proof carbon resistor(RDF25S22J 22 1/4W) [R740] Flame proof carbon resistor(RDF16S82KJ 82K 1/6W) [R742] Metal oxide film resistor(RSS5FB47J H1 47 5W) [R743] Flame proof fixed carbon film resistor(33K 1/4W) [R746,R747] Flame proof carbon resistor(RDF16S33KJ 33K 1/6W) [R748] Flame proof carbon resistor(RDF16S2.7KJ 2.7K 1/6W) [R751] Metal film resistor(SN16S22.3KD 22.3K 1/6W) [R754] Metal film resistor(SN16S2.55KD 2.55K 1/6W) [R755] Flame proof carbon resistor(RDF16S15KJ 15K 1/6W) [R756] Flame proof carbon resistor(RDF25S220J 220 1/4W) [R761] Flame proof carbon resistor(RDF25S4.7J 4.7 1/4W) [R762] Flame proof carbon resistor(RDF25S4.7KJ 4.7K 1/4W) [R763] Cement filled resistor(BPR05WFTR10J 0.01 5W) [R764] Flame proof carbon resistor(RDF16S5.6KJ 5.6K 1/6W) [R765] Fusing resistor(RF16S100J 100 1/6W) [R767] Flame proof carbon resistor(RDF25S120J 120 1/4W) [R769,R771] Flame proof carbon resistor(RDF16S12KJ 12K 1/6W) [R773] Metal film resistor(SN16S1.2KD 1.2K 1/6W) [R778] Metal film resistor(SN16S39KD 39K 1/6W) [R779] Metal oxide film resistor(RSF1B22J 22 1W) [R780] Flame proof carbon resistor(RDF16S330J 330 1/6W) [R781] Fixed carbon film resistor(RDF16S100J 100 1/6W) [R782] Flame proof carbon resistor(RDF16S390J 390 1/6W) [R783] Flame proof carbon resistor(RDF16S1.2KJ 1.2K 1/6W) [R785] Flame proof carbon resistor(RDF16S680J 680 1/6W) [R786] Flame proof carbon resistor(RDF16S120J 120 1/6W) [R791] Flame proof carbon resistor(RDF16S470J 470 1/6W) [R792,R814,R809,R826] Flame proof carbon resistor(RDF16S27KJ 27K 1/6W) [R793,R794] Flame proof carbon resistor(RDF16S56KJ 56K 1/6W) [R798] Fusing resistor(RF16S330J 330 1/6W) [R801] METAL OXIDE FILM RESISTOR(12K1W) [R804,R805] METAL OXIDE FILM RESISTOR(181W) [R806] FLAME PROOF CARBON RESISTOR(100K1/4W) [R811,R812] Flame proof carbon resistor(RDF16S47KJ 47K 1W) [R813,R819,R820] FLAME PROOF CARBON RESISTOR(56K 1/4W) [R733] Fusing resistor(RF16S22J 22 1/6W) [R816] Flame proof carbon resistor(RDF16S4.7KJ 4.7K 1/6W) [R821,R822,R752,R759,R774,R799] Flame proof carbon resistor(RDF16S100KJ 100K 1/6W) [R823] METALFILM RESISTOR(56K1/6W) [R745] Fusing resistor(10 1/4W) [R829] METAL FILM RESISTOR(1.5K 1/6W) [R729] METAL FILM RESISTOR(49.9K 1/6W) [R722] Transformer(N-T01-367) [T701]
TR No.
Effective time
82
0AV2011033010 0AV2011033010 0AV2021013078 0AV2013323010 0AV2021213040 0AV2018213010 0AV2013933010 0AV2148203040 0AV2012243010 0AV2011013030 0AV2012223010
83 84 85 86 87 88 89 90 91
0AV2012223010 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 ! 137 0AV2011813010 0AV2990105000 0AV2041213010 0AV2012203020 0AV2018233010 0AV2024703078 0AV2013333020 0AV2013333010 0AV2012723010 0AV2990083000 0AV2990010000 0AV2011533010 0AV2012213020 0AV2014773020 0AV2014723020 0AV2051094075 0AV2015623010 0AV2041013010 0AV2011213020 0AV2011233010 0AV2990084000 0AV2990085000 0AV2142203040 0AV2013313010 0AV2011013010 0AV2013913010 0AV2011223010 0AV2016813010 0AV2011213010 0AV2014713010 0AV2012733010 0AV2015633010 0AV2043313010 0AV2021233040 0AV2141803040 0AV2016104020 0AV2014733010 0AV2015633020 0AV2042203010 0AV2014723010 0AV2011043010 0AV2990104000 0AV2041003020 0AV2990107000 0AV2990112000 0AV4000136711
manuals4you.com
28-2
PARTS CODE
0AV4000131011 0AV3160033000 0AV3160037000 0AV2081029188 0AV5080011000 0AV5190002000 0AV5030126000 0AV5030127000 0AV5030036000 0AV5030128000 0AV5030129000 0AV5130009000 0AV5130011000 0AV8117730416 0AV8117730516 0AV8117730616 0AV6113116511 0AV6114150911 0AV6114150111 0AV5050005000 0AV7100003000 0AV5110012000 0AV5110012000 0AV5110012000 0AV5110012000 0AV5110003000 0AV5110003000 0AV5110001000 0AV5110001000 0AV5110006000 0AV5110006000 0AV5110006000 0AV5110002000 0AV5110011000 0AV5110004000 0AV5110004000 0AV5110004000 0AV5110004000 0AV5060186000 0AV5060188000 0AV5060190000 0AV5060089000 (Unit) RDENC0020FCZ6
160 161 162 163 164 165 165 166 167 168 169
! ! ! !
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AQ B Transformer(N-T01-310) [T702] AP B Traic(TM1641P) [TR701,TR703] AN B Traic [TR702] AC B Potentiometer(RH063MC13R 1K) [VR701,VR702] AP B Relay(ALE15B24) [RL701] AF C Varistor(ENC271D-10A-TA-B) [X701] AG C Connector(B03P-VL) [CN1] AD C Connector(B7B-PH-K-S) [CN2] AC C Connector(B2P3-VH) [CN3] AD C Connector(B03B-XASK-1) [CN4] AK C Connector(B12P-HL-A) [CN5] AD C Terminal(TP82224-31) AC C Terminal AC C Screw(38) AC C Screw(310) AC C Screw(312) AN C Heatsink(LM31165) AH C Heatsink AG C Heatsink AA C Holder(PFC5000-0203) AE C Insulation sheet(M-30AD-D-3) AB C Jumper wire(RJ-SKA-06) [RJ701,RJ702,RJ703,RJ708,RJ712] AB C Jumper wire(RJ-SKA-06) [RJ713,RJ721,RJ727,RJ730,RJ735] AB C Jumper wire(RJ-SKA-06) [RJ746,RJ760,RJ768,RJ769,RJ771] AB C Jumper wire(RJ-SKA-06) [RJ772,RJ773,RJ775,RJ776] AA C Jumper wire(RJ-SBA-06) [RJ707,RJ722,RJ723,RJ731,RJ736] AA C Jumper wire(RJ-SBA-06) [RJ738,RJ739,RJ743,RJ748,RJ778] AA C Jumper wire(RJ-SCA-06) [RJ711,RJ714,RJ716,RJ747,RJ756] AA C Jumper wire(RJ-SCA-06) [RJ757,RJ759,RJ770,RJ779] AA C Jumper wire(RJ-SDA-06) [RJ715,RJ718,RJ725,RJ726,RJ742] AA C Jumper wire(RJ-SDA-06) [RJ745,RJ752,RJ754,RJ758,RJ763] AA C Jumper wire(RJ-SDA-06) [RJ766,RJ774,RJ777] AA C Jumper wire(RJ-SEA-06) [RJ704,RJ728,RJ733,RJ734,RJ753] AB C Jumper wire(RJ-SFA-06) [RJ717,RJ729,RJ740,RJ741,RJ765] AA C Jumper wire(RJ-SGA-06) [RJ705,RJ706,RJ709,RJ710,RJ719] AA C Jumper wire(RJ-SGA-06) [RJ720,RJ724,RJ732,RJ737,RJ749] AA C Jumper wire(RJ-SGA-06) [RJ750,RJ751,RJ755,RJ761,RJ762] AA C Jumper wire(RJ-SGA-06) [RJ764,RJ767] AD A Fuse(6.3A/125V) [F701,F702] AE A Fuse(4A/125V) [F703] AE A Fuse(10A/125V) [F706] AE A Fuse(396 2 2A/125V) [F705] BV E AC/DC power supply PWB 100
TR No.
Effective time
! 901
28-3
PARTS CODE
0AV1570000002 0AV1570000003 0AV1570000004 0AV1650000064 0AV1570000005 0AV1390000272 0AV1690000133
35 36 37 38 39 40 41 42 43 44 45 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AD C FILM CAPACITOR(LE104-L 0.1F,250V(LE)) [C701] AD C FILM CAPACITOR(LE104-C 0.1F,250V(LE)) [C760,C761] AN C FILM CAPACITOR(LE155-C 1.5F,250V(LE)) [C702] AD C CERAMIC CAPACITOR(DE0813E472M-KH) [C703,C704] AF C FILM CAPACITOR(LE334-C) [C705] AY C AL-ELECTROLYTIC CAPACITOR(LGU2G561MELC) [C706] CERAMIC CAPACITOR(PRE132R104K50 0.1F,50V) AC C [C707,C718,C720,C730,C733] CERAMIC CAPACITOR(PRE132R104K50 0.1F,50V) AC C [C742,C752,C756,C759,C765] CERAMIC CAPACITOR(DE0905-979R102K1K 1000pF,1KV) AC C [C708,C749,C726,C747,C748] AC C AL-ELECTROLYTIC CAPACITOR(UPJ1H4R7MDD 4.7F,50V) [C711] AL-ELECTROLYTIC CAPACITOR(UPJ1H220MED 22F,50V) AC C [C712,C766,C768] AE C CERAMIC CAPACITOR(DE1610-2E472M-KX 4700pF(KX)) [C713,C767] AD C FILM CAPACITOR(CQMY-92MC2A104J 0.1F,100V) [C714,C715] CERAMIC CAPACITOR(RPE132R103K50 0.01F,50V) AC C [C716,C717,C763] AC C CERAMIC CAPACITOR(RPE132R472K50 4700pF,50V) [C719,C757] AC C CERAMIC CAPACITOR(DE0705-979R331K2K) [C721,C722] AL-ELECTROLYTIC CAPACITOR(UPJ1V182MHD6 1800F,35V) AC C [C728,C729] AC C AL-ELECTROLYTIC CAPACITOR(UPJ1H010MDD 1F,50V) [C734,C771] AC C AL-ELECTROLYTIC CAPACITOR(UHD1V681MHD 680F,35V) [C735] AG C AL-ELECTROLYTIC CAPACITOR(UHD1V102MHD 1000F,35V) [C738] AD C CERAMIC CAPACITOR(TPZ11R152K1K) [C709,C710] AD C CERAMIC CAPACITOR(RPE132R223K50) [C739,C744,C746,C755] AL-ELECTROLYTIC CAPACITOR(UPJ1H2R2MDD 2.2F,50V) AC C [C740,C753] AC C AL-ELECTROLYTIC CAPACITOR(UHD1C222MHD 2200F,16V) [C741] CERAMIC CAPACITOR(RPE132R102K50 1000pF,50V) AC C [C743,C745,C770] AL-ELECTROLYTIC CAPACITOR(UHD1A562MHD 5600F,10V) AK C [C750,C751] AD C AL-ELECTROLYTIC CAPACITOR(UPJ1V820MED 82F,35V) [C754] AE C FILM CAPACITOR(ECQE2104RJF 0.1F,400V) [C764] AC C AL-ELECTROLYTIC CAPACITOR(UPJ1C101MED 100F,16V) [C772] AD B CERAMIC CAPACITOR(TRPE132R12K50) [C773] AE B DIODE(S1WB(A)60 1A,600V) [D701] AC B ZENER DIODE(RD6.8ES 400mW) [D702] AC B DIODE(ERA15-06) [D703,D704,D748,D763] AF B DIODE(ERA91-02 0.5A,200V) [D706,D708,D710,D717,D746] AF B DIODE(ERA91-02 0.5A,200V) [D747,D755,D758,D759] AB B DIODE(1SS270 60V,150mA) [D707,D714,D726,D727,D728] AB B DIODE(1SS270 60V,150mA) [D731,D733,D737,D738,D743] AB B DIODE(1SS270 60V,150mA) [D744,D751,D751,D752] AB B DIODE(1SS270 60V,150mA) [D754,D760,D762] AC B ZENER DIODE(RD33ES 400mW) [D709] AC B ZENER DIODE(RD39ES) [D712,D756] AD B ZENER DIODE(RD20ES 400mW) [D716] AB B ZENER DIODE(RD5.6ES 400mW) [D715,D720,D734,D736,D739] AN B DIODE(YG906C2R 20A,200V) [D721] AC B ZENER DIODE(RD4.7ES 400mW) [D724] AK B DIODE(YG802C06 10A,60V) [D729] AP B DIODE(YG805C04 20A,40V) [D730] AC B ZENER DIODE(RD3.9ES 400mW) [D732] AD B ZENER DIODE(RD62E) [D735] AD B ZENER DIODE(RD20ES 400mW) [D749] AC B ZENER DIODE(RD3.0ES 400mW) [D745,D753] AE B ZENER DIODE(RD24ES 400mW) [D713,D757] AB B ZENER DIODE(RD27ES 400mW) [D761] AC B ZENER DIODE(RD4.3ES 400mW) [D765] AD B DIODE(AK04) [D750,D764] AL B IC(FA5515P) [IC701,IC705] AF B IC(UPC1093J-1) [IC702,IC704] AK B IC(MB3759P) [IC703] AR C INDUCTOR(DRC31-08A402) [L701] AM C INDUCTOR(DRB25-03A502) [L702] AC C INDUCTOR(T314OP3206536HW) [L703,L710] AG C INDUCTOR(PC8T8R2M) [L707] AD C INDUCTOR(LFP3A) [L708] AL C INDUCTOR(HK-10S100-4500S) [L709] AC C INDUCTOR(B-01-A) [L711,L713,L714,L715] AH C INDUCTOR(PC8T3R3M) [L712] AE B PHOTO COUPLER(TLP421) [PC701,PC703,PC704,PC706] AL B PHOTO TRIAC COUPLER(PC3SF11YV) [PC702,PC705] AU B FET(2SK2611) [Q701] AC B TRANSISTOR(2SA1015 -50V,-150mA) [Q702,Q713] AR B FET(2SK2717) [Q704]
TR No.
Effective time
manuals4you.com
29-1
PARTS CODE
0AV3021815500 0AV3021815500 0AV3040504000 0AV3022655500 0AV3042736000 0AV3021002999 0AV2024713040 0AV2051064077 0AV2012733030 0AV2012233010 0AV2011843030 0AV2990118000 0AV2011853010 0AV2011023010 0AV2052294055 0AV2012243020 0AV2011213030 0AV2011203020 0AV2011033010 0AV2021013078 0AV2013323010 0AV2021213040 0AV2990142000 0AV2013933010 0AV2148203040 0AV2012243010 0AV2011013020 0AV2990098000 0AV2012223010
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AC B TRANSISTOR(2SC1815 50V 150mA) [Q706,Q709,Q710,Q711,Q714] AC B TRANSISTOR(2SC1815 50V 150mA) [Q715,Q717,Q718,Q719,Q723] AN B FET(2SJ504) [Q707] AE B TRANSISTOR(2SC2655) [Q708] AN B FET(2SK2736) [Q712] AD B TRANSISTOR(RN1002) [Q720,Q721,Q722] AC C METAL OXIDE FILM RESISTOR(RSU01WST5A471J) [R701] AF C CEMENT FILLED RESISTOR(MNS05WNZ100J) [R702] FLAME PROOF CARBON RESISTOR(RDF50S27KJ) AB C [R703,R704,R705] FLAME PROOF CARBON RESISTOR(RDF16S22KJ 22K,1/6W) AA C [R706,R772,R827,R828] FLAME PROOF CARBON RESISTOR(RDF50S180KJ 180 1/2W) AB C [R707] AC C METAL OXIDE FILM RESISTOR(SPF01W82KF) [R708,R709] AB C FLAME PROOF CARBON RESISTOR(RDF16S1.8MJ) [R710] FLAME PROOF CARBON RESISTOR(RDF16S1KJ 1K,1/6W) AA C [R711,R737,R750,R784,R817,R751] AE C CEMENT FILLED RESISTOR(BPR02WFTR22J) [R739] FLAME PROOF CARBON RESISTOR(RDF25S220KJ) AA C [R713,R714,R811,R812] FLAME PROOF CARBON RESISTOR(RDF50S120J 120 1/2W) AB C [R715,R732,R726,R728] AB C FLAME PROOF CARBON RESISTOR(RDF25S12J 121/4W) [R716] FLAME PROOF CARBON RESISTOR(RDF16S10KJ 10K,1/6W) AA C [R717,R730,R735,R741,R753,R758] METAL OXIDE FILM RESISTOR(RSS5FB100JH1 100 5W) AF C [R718,R744] FLAME PROOF CARBON RESISTOR(RDF16S3.3KJ 3.3K 1/6W) AA C [R719,R775] AC C METAL OXIDE FILM RESISTOR(RSF1B120J 120 1W) [R720,R731] AA C METAL FILM RESISTOR(SN16S909D 909 1/6W) [R721] FLAME PROOF CARBON RESISTOR(RDF16S39KJ 39K,1/6W) AA C [R790] AC C METAL OXIDE FILM RESISTOR(RSS182J 82 1W) [R723] FLAME PROOF CARBON RESISTOR(RDF16S220KJ 220K,1/6W) AA C [R724] AA B FUSING RESISTOR(RF25S100J) [R725,R727] AD C METAL OXIDE FILM RESISTOR(RSMF2BR22F) [R712] FLAME PROOF CARBON RESISTOR(RDF16S2.2KJ 2.2K,1/6W) AA C [R749,R766,R777,R807,R808] FLAME PROOF CARBON RESISTOR(RDF16S2.2KJ 2.2K,1/6W) AA C [R815,R810,R797] FLAME PROOF CARBON RESISTOR(RDF16S180J 180,1/6W) AA C [R768] AB C METAL FILM RESISTOR(SN16S68KD 68K,1/6W) [R736] AC B FUSING RESISTOR(RF16S150J) [R738] AA C FLAME PROOF CARBON RESISTOR(RDF25S22J 22 1/4W) [R740] FLAME PROOF CARBON RESISTOR(RDF16S82KJ 82K,1/6W) AA C [R742] AF C METAL OXIDE FILM RESISTOR(RSS5FB47JH1 47 5W) [R743] AB C FLAME PROOF CARBON RESISTOR(RDF25S270KJ) [R746,R747] FLAME PROOF CARBON RESISTOR(RDF16S33KJ 33K 1/6W) AA C [R748] AC C METAL FILM RESISTOR(SN16S180D) [R734] AC C METAL FILM RESISTOR(SN16S22.3KD 22.3K 1/6W) [R754] AC C METAL FILM RESISTOR(SN16S2.55KD 2.55K 1/6W) [R755] FLAME PROOF CARBON RESISTOR(RDF16S15KJ 15K 1/6W) AA C [R756] FLAME PROOF CARBON RESISTOR(RDF25S220J 220 1/4W) AA C [R761] AA C FLAME PROOF CARBON RESISTOR(RDF25S4.7J 4.7 1/4W) [R762] AA C FLAME PROOF CARBON RESISTOR(RDF25S4.7KJ) [R763] AG C CEMENT FILLED RESISTOR(BPR05WFTR10J 0.01 5W) [R764] FLAME PROOF CARBON RESISTOR(RDF16S5.6KJ 5.6K 1/6W) AA C [R765] AC B FUSING RESISTOR(RF16S100J 100 1/6W) [R767] FLAME PROOF CARBON RESISTOR(RDF25S120J 120 1/4W) AA C [R769,R771] FLAME PROOF CARBON RESISTOR(RDF16S12KJ 12K 1/6W) AA C [R773] AC C METAL FILM RESISTOR(SN16S1.2KD 1.2K 1/6W) [R778] AC C METAL FILM RESISTOR(SN16S39KD 39K 1/6W) [R779] AC C METAL OXIDE FILM RESISTOR(RSF1B22J 22 1W) [R780] FLAME PROOF CARBON RESISTOR(RDF16S330J 330 1/6W) AA C [R781] FLAME PROOF CARBON RESISTOR(RDF16S100J 100 1/6W) AA C [R782] FLAME PROOF CARBON RESISTOR(RDF16S390J 390 1/6W) AA C [R783] FLAME PROOF CARBON RESISTOR(RDF16S1.2KJ 1.2K 1/6W) AA C [R785]
TR No.
Effective time
29-2
PARTS CODE
0AV2016813010 0AV2011213010 0AV2014713010 0AV2012733010 0AV2015633010 0AV2043313010 0AV2023333040 0AV2142703040 0AV2014733010 0AV2015633020 0AV2042203010 0AV2014723010 0AV2011043010 0AV2990104000 0AV2041003020 0AV2990107000 0AV2990112000 0AV2012223010 0AV2060026000 0AV4000139011 0AV4000138911 0AV3160034000 0AV3160032000 0AV2081029188 0AV5080013000 0AV5190003000 0AV5030126000 0AV5030127000 0AV5030128000 0AV5030129000 0AV5030149000 0AV5030088000 0AV5130009000 0AV5130011000 0AV8117730416 0AV8117730516 0AV8117730616 0AV6113116511 0AV6114150911 0AV6114150111 0AV5050005000 0AV7100003000 0AV5110012000 0AV5110012000 0AV5110012000 0AV5110012000 0AV5110003000 0AV5110003000 0AV5110001000 0AV5110001000 0AV5110006000 0AV5110006000 0AV5110006000 0AV5110002000 0AV5110011000 0AV5110004000 0AV5110004000 0AV5110004000 0AV5110004000 0AV5110004000 0AV5060093000 0AV5060094000 0AV5060095000 (Unit) RDENC0037FCZ3
DESCRIPTION
FLAME PROOF CARBON RESISTOR(RDF16S680J 680 1/6W) [R786] FLAME PROOF CARBON RESISTOR(RDF16S120J 120 1/6W) [R791] FLAME PROOF CARBON RESISTOR(RDF16S470J) [R792,R814,R809,R826] FLAME PROOF CARBON RESISTOR(RDF16S27KJ) [R793,R794] FLAME PROOF CARBON RESISTOR(RDF16S56KJ) [R798] FUSING RESISTOR(RF16S330J) [R801] METAL OXIDE FILM RESISTOR(RSF1B33KJ) [R804,R805] METAL OXIDE FILM RESISTOR(RSMF1B27J) [R806] FLAME PROOF CARBON RESISTOR(RDF16S47KJ) [R813,R819,R820] FLAME PROOF CARBON RESISTOR(RDF25S56KJ) [R733] FUSING RESISTOR(RF16S22J) [R816] FLAME PROOF CARBON RESISTOR(RDF16S4.7KJ) [R821,R822,R752,R759,R774,R799] FLAME PROOF CARBON RESISTOR(RDF16S100KJ) [R823] METAL FILM RESISTOR(SN16S56KD) [R745] FUSING RESISTOR(RF25S10J) [R829] METAL FILM RESISTOR(SN16S1.5KD) [R729] METAL FILM RESISTOR(SN16S49.9KD) [R722] FLAME PROOF CARBON RESISTOR(RDF16S2.2KJ 2.2K,1/6W) [R760] TEMP.FUSING RESISTOR(MEG05N100KB142) [FR701] Transformer(N-T01-390) [T701] Transformer(N-T01-389) [T702] Traic(TM1661P) [TR701,TR703] Traic(BCR8PM-12LP) [TR702] POTENTIOMETER(RH063MC13R) [VR701,VR702] RELAY(OMIH-SS-124LM) [RL701] Varistor(ENC471D-10A-TA-B) [X701] Connector(B03P-VL) [CN1] Connector(B7B-PH-K-S) [CN2] Connector(B03B-XASK-1) [CN4] Connector(B12P-HL-A) [CN5] Connector(B5P-VH) [CN6] Connector(B2P-VH) [CN7] TERMINAL(TP82224-31) TERMINAL(TP00370-21) SCREW(NACPEW-B3X8SF) SCREW(NACPEW-B3X10SF) SCREW(NACPEW-B3X12SF) HEATSINK(LM31165) HEATSINK(LM41509) HEATSINK(LM41510) HOLDER(PFC5000-0203) INSULATION SHEET(M-30AD-D-3) Jumper wire(RJ-SKA-06) [RJ701,RJ702,RJ703,RJ708,RJ712] Jumper wire(RJ-SKA-06) [RJ713,RJ721,RJ727,RJ730,RJ735] Jumper wire(RJ-SKA-06) [RJ746,RJ760,RJ768,RJ769,RJ771] Jumper wire(RJ-SKA-06) [RJ772,RJ773,RJ775,RJ776] Jumper wire(RJ-SBA-06) [RJ707,RJ722,RJ723,RJ731,RJ736] Jumper wire(RJ-SBA-06) [RJ738,RJ739,RJ743,RJ748,RJ778] Jumper wire(RJ-SCA-06) [RJ711,RJ714,RJ716,RJ747] Jumper wire(RJ-SCA-06) [RJ756,RJ757,RJ759,RJ770,RJ779] Jumper wire(RJ-SDA-06) [RJ715,RJ718,RJ725,RJ726,RJ742] Jumper wire(RJ-SDA-06) [RJ745,RJ752,RJ754,RJ758,RJ763] Jumper wire(RJ-SDA-06) [RJ766,RJ774,RJ777] Jumper wire(RJ-SEA-06) [RJ704,RJ728,RJ733,RJ734,RJ753] Jumper wire(RJ-SFA-06) [RJ717,RJ729,RJ740,RJ741,RJ765] Jumper wire(RJ-SGA-06) [RJ705,RJ706,RJ709,RJ710] Jumper wire(RJ-SGA-06) [RJ719,RJ720,RJ724,RJ732] Jumper wire(RJ-SGA-06) [RJ737,RJ749,RJ750,RJ751] Jumper wire(RJ-SGA-06) [RJ755,RJ761,RJ762,RJ764] Jumper wire(RJ-SGA-06) [RJ767,RJ780,RJ781] FUSE(6.3A/250V) [F701,F702,F704,F706] FUSE(4A/250V) [F703] FUSE(MRT2.0) [F705] AC/DC power supply PWB 200
TR No.
Effective time
172
manuals4you.com
29-3
PARTS CODE
0AV1560000009 0AV1560000002 0AV1560000008 0AV1690000074 0AV1560000004 0AV1390000272 0AV1690000133 0AV1690000133 0AV1610000091 0AV1610000090 0AV1390000261 0AV1390000262 0AV1690000113 0AV1480000109 0AV1690000134 0AV1690000138 0AV1610000039 0AV1390000263 0AV1390000264 0AV1390000265 0AV1390000266 0AV1690000136 0AV1390000267 0AV1390000268 0AV1690000137 0AV1390000269 0AV1390000270 0AV1480000107 0AV1390000271 0AV3060035000 0AV3070123000 0AV3060045000 0AV3060025000 0AV3050019000 0AV3050019000 0AV3050086000 0AV3050086000 0AV3050086000 0AV3070128000 0AV3070116000 0AV3070130000 0AV3070119000 0AV3070115000 0AV3050087000 0AV3070132000 0AV3050070000 0AV3050080000 0AV3070124000 0AV3070131000 0AV3070089000 0AV3070126000 0AV3070141000 0AV3070127000 0AV3050104000 0AV2060026000 0AV3090079000 0AV3090041000 0AV3090008000 0AV4070066000 0AV4070067000 0AV4120013000 0AV4050016000 0AV4120008000 0AV4080014000 0AV4120002000 0AV4050010000 0AV3080421100 0AV3180000009 0AV3042611000 0AV3001015500 0AV3042717000 0AV3021815500 0AV3021815500 0AV3040504000 0AV3022655500 0AV3042736000 0AV3021002999 0AV2024713040 0AV2051064077
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AE C Film capacitor(RE104-L 0.1F 250V(RE)) [C701] AD C Film capacitor(RE104-C 0.1F 250V(RE)) [C760,C761] AR C Film capacitor(RE155-C 1.5F 250V(RE)) [C702] AD C Ceramic capacitor(DE0807E102M-KH 1000PF(KH)) [C703,C704] AG C FILM CAPACITOR(0.33F 250V(RE)) [C705] AY C AL-ELECTROLYTIC CAPACITOR(560F 400V) [C706] AC C CERAMIC CAPACITOR(0.1F 50V) [C707,C718,C720,C730,C733] AC C CERAMIC CAPACITOR(0.1F 50V) [C742,C752,C756,C759,C765] Ceramic capacitor(DE0905-979R102K1K 1000PF 1KV) AC C [C708,C726,C747,C748,C749] AD C CERAMIC CAPACITOR(1500PF 1KV) [C709,C710] AC C AL-ELECTROLYTIC CAPACITOR(4.7F 50V) [C711] AC C AL-ELECTROLYTIC CAPACITOR(22F 50V) [C712,C766,C768] AE C Ceramic capacitor(DE1610-2E472M-KX 4700PF(KX)) [C713,C767] AD C FILM CAPACITOR(0.1F 50V) [C714,C715] AC C CERAMIC CAPACITOR(0.01F 50V) [C716,C717,C763] AC C CERAMIC CAPACITOR(4700PF 50V) [C719,C757] AB C Ceramic capacitor(330pF 2KV) [C721,C722] AC C AL-ELECTROLYTIC CAPACITOR(1800F 35V) [C728,C729] AC C AL-ELECTROLYTIC CAPACITOR(1F 50V) [C734,C771] AC C AL-ELECTROLYTIC CAPACITOR(680F 35V) [C735] AG C AL-ELECTROLYTIC CAPACITOR(1000F 35V) [C738] AD C CERAMIC CAPACITOR(0.022F 50V) [C739,C744,C746,C755] AC C AL-ELECTROLYTIC CAPACITOR(2.2F 50V) [C740,C753] AC C AL-ELECTROLYTIC CAPACITOR(2200F 16V) [C741] AC C CERAMIC CAPACITOR(1000PF 50V) [C743,C745,C770,C773] AK C AL-ELECTROLYTIC CAPACITOR(5600F 10V) [C750,C751] AD C AL-ELECTROLYTIC CAPACITOR(82F 35V) [C754] AE C FILM CAPACITOR(0.1F 400V) [C764] AC C AL-ELECTROLYTIC CAPACITOR(100F 16V) [C772] AE B Diode(S1WB(A)60 1A 600V) [D701] AC B Zenner diode(RD6.8ES 400mw) [D702] AC B Diode(1A 600V) [D703,D704,D748,D763] AK B Zenner diode(5A 600V)(D5SB60) [D705] AF B Diode(ERA91-02 0.5A 200V) [D706,D708,D710,D717,D746] AF B Diode(ERA91-02 0.5A 200V) [D747,D755,D758,D759] AB B Diode(1SS270A 0.15A 60V) [D707,D714,D726,D727,D728] AB B Diode(1SS270A 0.15A 60V) [D731,D733,D737,D738,D743] AB B Diode(1SS270A 0.15A 60V) [D744,D751,D752,D754,D760,D762] AC B Zenner diode(RD33ES 400mW) [D709] AC B Zenner diode(400mW) [D712,D756] AC B Zenner diode(400mW) [D713,D757] AC B Zenner diode(RD5.6ES 400mW) [D715,D720,D734,D736,D739] AC B Zenner diode(RD20ES 400mW) [D716,D749] AN B Diode(YG906C2R 20A 200V) [D721] AC B Zenner diode(RD4.7ES 400mW) [D724] AK B Diode(YG802C06 10A 60V) [D729] AP B Diode(YG805C04 20A 40V) [D730] AC B Zenner diode(RD3.9ES 400mW) [D732] AD B Zenner diode(500mW) [D735] AC B Zenner diode(RD10ES) [D742] AC B Zenner diode(RD3.0ES 400mW) [D745,D753] AC B Zenner diode(400mW) [D765] AC B Zenner diode(RD27ES 400mW) [D761] AD B Diode(1A40V) [D750,D764] AK C TEMP.FUSING RESISTOR(MEG05N100KB142) [FR701] AL B IC(FA5515P) [IC701,IC705] AF B IC(UPC1093J-1) [IC702,IC704] AK B IC(MB3759M) [IC703] AR C Inductor(DRC31-08A402) [L701] AM C Inductor(DRB25-03A502) [L702] AC C Inductor(T314OP3206536HW) [L703,L710] AG C Inductor(PC8T8R2M) [L707] AD C Inductor(LFP3A) [L708] AL C Inductor(HK-10S100-4500S) [L709] AC C Inductor(B-01-A) [L711,L713,L714,L715] AH C Inductor(PC8T3R3M) [L712] AE B Photo coupler(TLP421GR) [PC701,PC703,PC704,PC706,PC707] AL B Photo coupler(PC3SF11) [PC702,PC705] AU B Transistor(900V 9A) [Q701] AC B Transistor(2SA1015 -50V -150mA) [Q702,Q713] AR B Transistor(900V 5A) [Q704] AC B Transistor(2SC1815 50V 150mA) [Q706,Q709,Q710,Q711,Q714] AC B Transistor(2SC1815 50V 150mA) [Q715,Q717,Q718,Q719,Q723] AN B Transistor(2SJ504) [Q707] AE B Transistor(2SC2655) [Q708] AN B Transistor(2SK2736) [Q712] AD B Transistor(RN1002) [Q720,Q721,Q722] AC C METAL OXIDE FILM RESISTOR(470 1W) [R701] AF C CEMENT FILLED RESISTOR(10 5W) [R702]
TR No.
Effective time
manuals4you.com
30-1
PARTS CODE
0AV2012733030 0AV2012233010 0AV2011843030 0AV2990118000 0AV2011853010 0AV2011023010 0AV2052294055 0AV2012243020 0AV2011213030 0AV2011203020 0AV2011033010
85
0AV2011033010 0AV2011033010 0AV2021013078 0AV2013323010 0AV2021213040 0AV2990099000 0AV2013933010 0AV2148203040 0AV2012243010 0AV2011013020 0AV2012223010
86 87 88 89 90 91 92 93 94
0AV2012223010 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 ! 140 ! 141 0AV2015633020 0AV2011813010 0AV2990105000 0AV2041513010 0AV2012203020 0AV2018233010 0AV2024703078 0AV2012743020 0AV2013333010 0AV2012733010 0AV2990083000 0AV2990010000 0AV2011533010 0AV2012203020 0AV2014773020 0AV2014723020 0AV2051094075 0AV2015623010 0AV2041013010 0AV2011213020 0AV2011233010 0AV2990084000 0AV2990085000 0AV2142203040 0AV2013303010 0AV2011003010 0AV2013903010 0AV2011223010 0AV2016813010 0AV2011203010 0AV2014713010 0AV2012733010 0AV2015633010 0AV2043313010 0AV2023333040 0AV2142703040 0AV2014733010 0AV2042203010 0AV2014723010 0AV2011043010 0AV2990090000 0AV2990119000 0AV2990104000 0AV2041003020 0AV2990112000 0AV4000139011 0AV4000138911
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AB C FLAME PROOF CARBON RESISTOR(27K 1/2W) [R703,R704,R705] Flame proof carbon resistor(RDF16S22KJ 22K 1/6W) AA C [R706,R772,R827,R828] AB C Flame proof carbon resistor(RDF50S180KJ 180K 1/2W) [R707] AC C METAL OXIDE FILM RESISTOR(82K1W) [R708,R709] AB C FLAME PROOF CARBON RESISTOR(1.8M1/6W) [R710] Flame proof carbon resistor(RDF16S1KJ 1K 1/6W) AA C [R711,R737,R750,R784,R817] AE C CEMENT FILLED RESISTOR(0.222W) [R712,R739] Fixed carbon film resistor(RDF25S220KJ 220K 1/4W) AA C [R713,R714,R811,R812] Flame proof carbon resistor(RDF50S120J 120 1/2W) AB C [R715,R726,R728,R732] AB C Flame proof carbon resistor(RDF25S12J 12 1/4W) [R716] Flame proof carbon resistor(RDF16S10KJ 10K 1/6W) AA C [R717,R730,R735,R741,R753] Flame proof carbon resistor(RDF16S10KJ 10K 1/6W) AA C [R758,R776,R795,R800,R818] AA C Flame proof carbon resistor(RDF16S10KJ 10K 1/6W) [R824,R825] AF C Metal oxide film resistor(RSS5FB100J H1 100 5W) [R718,R744] AA C Flame proof carbon resistor(RDF16S3.3KJ 3.3K 1/6W) [R719,R775] AC C METAL OXIDE FILM RESISTOR(120 1W) [R720,R731] AC C METAL FILM RESISTOR(942 1/6W) [R721] AA C Flame proof carbon resistor(RDF16S39KJ 39K 1/6W) [R790] AC C Metal oxide film resistor(RSS182J 82 1W) [R723] AA C Flame proof carbon resistor(RDF16S220KJ 220K 1/6W) [R724] AA C Flame proof fixed carbon film resistor(100 1/4W) [R725,R727] Flame proof carbon resistor(RDF16S2.2KJ 2.2K 1/6W) AA C [R749,R760,R766,R777,R797] Flame proof carbon resistor(RDF16S2.2KJ 2.2K 1/6W) AA C [R815,R807,R808,R810] AA C FLAME PROOF CARBON RESISTOR(56K 1/6W) [R733] AA C Flame proof carbon resistor(RDF16S180J 180 1/6W) [R768] AB C METAL FILM RESISTOR(68K 1/6W) [R736] AC C Fusing resistor(150 1/6W) [R738] AA C Flame proof carbon resistor(RDF25S22J 22 1/4W) [R740] AA C Flame proof carbon resistor(RDF16S82KJ 82K 1/6W) [R742] AF C Metal oxide film resistor(RSS5FB47J H1 47 5W) [R743] AB C Flame proof fixed carbon film resistor(270K 1/4W) [R746,R747] AA C Flame proof carbon resistor(RDF16S33KJ 33K 1/6W) [R748] AA C Flame proof carbon resistor(RDF16S27KJ 2.7K 1/6W) [R751] AC C Metal film resistor(SN16S22.3KD 22.3K 1/6W) [R754] AC C Metal film resistor(SN16S2.55KD 2.55K 1/6W) [R755] AA C Flame proof carbon resistor(RDF16S15KJ 15K 1/6W) [R756] AA C Flame proof carbon resistor(RDF25S22J 220 1/4W) [R761] AA C Flame proof carbon resistor(RDF25S4.7J 4.7 1/4W) [R762] AA C Flame proof carbon resistor(RDF25S4.7KJ 4.7K 1/4W) [R763] AG C Cement filled resistor(BPR05WFTR10J 0.01 5W) [R764] AA C Flame proof carbon resistor(RDF16S5.6KJ 5.6K 1/6W) [R765] AC C Fusing resistor(RF16S100J 100 1/6W) [R767] AA C Flame proof carbon resistor(RDF25S120J 120 1/4W) [R769,R771] AA C Flame proof carbon resistor(RDF16S12KJ 12K 1/6W) [R773] AC C Metal film resistor(SN16S1.2KD 1.2K 1/6W) [R778] AC C Metal film resistor(SN16S39KD 39K 1/6W) [R779] AC C Metal oxide film resistor(RSF1B22J 22 1W) [R780] AA C Flame proof carbon resistor(33 1/6W) [R781] AA C Flame proof carbon resistor(RDF16S100J 100 1/6W) [R782] AB C FLAME PROOF CARBON RESISTOR(390 1/6W) [R783] AA C Flame proof carbon resistor(RDF16S1.2KJ 1.2K 1/6W) [R785] AA C Flame proof carbon resistor(RDF16S680J 680 1/6W) [R786] AC C FLAME PROOF CARBON RESISTOR(1201/6W) [R791] Flame proof carbon resistor(RDF16S470J 470 1/6W) AA C [R792,R809,R814,R826] AA C Flame proof carbon resistor(RDF16S27KJ 27K 1/6W) [R793,R794] AA C Flame proof carbon resistor(RDF16S56KJ 56K 1/6W) [R798] AC C Fusing resistor(RF16S330J 330 1/6W) [R801] AC C METAL OXIDE FILM RESISTOR(33K1W) [R804,R805] AC C METAL OXIDE FILM RESISTOR(271W) [R806] Flame proof carbon resistor(RDF16S47KJ 47K 1/6W) AA C [R813,R819,R820] AC C Fusing resistor(RF16S22J 22 1/6W) [R816] Flame proof carbon resistor(RDF16S4.7KJ 4.7K 1/6W) AA C [R752,R759,R774,R799,R821,R822] AA C Flame proof carbon resistor(RDF16S100KJ 100K 1/6W) [R823] AC C METAL FILM RESISTOR(180 1/6W) [R734] AC C METAL FILM RESISTOR(1.6K 1/6W) [R729] AC C METAL FILM RESISTOR(56K 1/6W) [R745] AC C Fusing resistor(10 1/4W) [R829] AC C METAL FILM RESISTOR(49.9K 1/6W) [R722] AX B Transformer(N-T01-390) [T701] AQ B Transformer(N-T01-389) [T702]
TR No.
Effective time
manuals4you.com
PARTS CODE
0AV3160034000 0AV3160032000 0AV2081029188 0AV5080011000 0AV5190003000 0AV5030126000 0AV5030127000 0AV5030036000 0AV5030128000 0AV5030129000 0AV5130009000 0AV5130011000 0AV8117730416 0AV8117730516 0AV8117730616 0AV6113116511 0AV6114150911 0AV6114150111 0AV5050005000 0AV7100003000 0AV5110012000 0AV5110012000 0AV5110012000 0AV5110012000 0AV5110003000 0AV5110003000 0AV5110001000 0AV5110001000 0AV5110006000 0AV5110006000 0AV5110006000 0AV5110002000 0AV5110011000 0AV5110004000 0AV5110004000 0AV5110004000 0AV5110004000 0AV5060093000 0AV5060094000 0AV5060095000 (Unit) RDENC0021FCZ6
163 164 165 166 167 168 ! 169 ! 170 ! 171 ! 901
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AQ B Triac(TM1641PLF113) [TR701,TR703] AN B Traic(BCR8KM-12LA) [TR702] AC B Potentiometer(RH063MC13R 1K) [VR701,VR702] AP B Relay(ALE15B24) [RL701] AF C Varistor(ENC471D-10A) [X701] AG C Connector(B03P-VL) [CN1] AD C Connector(B7B-PH-K-S) [CN2] AC C Connector(B2P3-VH) [CN3] AD C Connector(B03B-XASK-1) [CN4] AK C Connector(B12P-HL-A) [CN5] AD C Terminal(TP82224-31) AC C Terminal(TP00370-21) AC C Screw(38) AC C Screw(310) AC C Screw(312) AN C Heatsink(LM31165) AH C Heatsink(LM41509) AG C Heatsink(LM41510) AA C Holder(PFC5000-0203) AE C Insulation sheet(M-30AD-D-3) AB C Jumper wire(RJ-SKA-06) [RJ701,RJ702,RJ703,RJ708,RJ712] AB C Jumper wire(RJ-SKA-06) [RJ713,RJ721,RJ727,RJ730,RJ735] AB C Jumper wire(RJ-SKA-06) [RJ746,RJ760,RJ768,RJ769,RJ771] AB C Jumper wire(RJ-SKA-06) [RJ772,RJ773,RJ775,RJ776] AA C Jumper wire(RJ-SBA-06) [RJ707,RJ722,RJ723,RJ731,RJ736] AA C Jumper wire(RJ-SBA-06) [RJ738,RJ739,RJ743,RJ748,RJ778] AA C Jumper wire(RJ-SCA-06) [RJ711,RJ714,RJ716,RJ747,RJ756] AA C Jumper wire(RJ-SCA-06) [RJ757,RJ759,RJ770,RJ779] AA C Jumper wire(RJ-SDA-06) [RJ715,RJ718,RJ725,RJ726,RJ742] AA C Jumper wire(RJ-SDA-06) [RJ745,RJ752,RJ754,RJ758,RJ763] AA C Jumper wire(RJ-SDA-06) [RJ766,RJ774,RJ777] AA C Jumper wire(RJ-SEA-06) [RJ704,RJ728,RJ733,RJ734,RJ753] AB C Jumper wire(RJ-SFA-06) [RJ717,RJ729,RJ740,RJ741,RJ765] AA C Jumper wire(RJ-SGA-06) [RJ705,RJ706,RJ709,RJ710,RJ719] AA C Jumper wire(RJ-SGA-06) [RJ720,RJ724,RJ732,RJ737,RJ749] AA C Jumper wire(RJ-SGA-06) [RJ750,RJ751,RJ755,RJ761,RJ762] AA C Jumper wire(RJ-SGA-06) [RJ764,RJ767,RJ780,RJ781] AF A Fuse(6.3A/250V) [F701,F702,706] AE A Fuse(4A/250V) [F703] AF A Fuse(2A/250V) [F705] BW E AC/DC power supply PWB 200
TR No.
Effective time
30-3
[ Exteriors[AR-EF3/5/6]
NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
PARTS CODE
GCAB-0943FCNZ XHBS740P08000 PCOVP1566FCN1 PCOVP1879FCZ1 LX-BZ0842FCPZ XHBS740P08000 GCAB-0942FCN1 GCAB-1081FCZZ LX-BZ0776FCPZ XHBS740P08000 GCAB-0945FCNZ DUNT-7133DS14 DUNT-7133DS15 LFIX-0544FCNZ CGLSP0003RS52 XBTSC50P16000 LFIX-0543FCNZ CGLSP0102DS51 XHBS730P06000 XBTS740P06000 PGIDM1900FCNZ PGIDM1901FCNZ NROLP0011QSZZ PCUSS0383FCZZ NSFTZ2601FCZZ MSPRC2865FCZ1 XEBS730P08000 PCOVP1624FCZZ LX-BZ0465FCWZ XHBS730P08000 CPNLC0244DS58 CPNLC0244DS63 LDAIU0627FCNZ XEBS740P08000 PMLT-1256FCZZ PMLT-1257FCZZ RCORF0041FCZZ PMLT-1402FCZZ PMLT-1404FCZZ PMLT-1405FCZZ PMLT-1406FCZZ PSHEP5190FCZZ PSEL-0886FCZZ
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AH D Rear lower cabinet AA C Screw(48) AV D Upper cabinet rear cover AR D Upper cabinet rear cover AH C SPF screw AA C Screw(48) AS D Upper cabinet rear AV D Upper cabinet rear AG C Screw R AA C Screw(48) AR D Upper cabinet right CR E DSPF unit CS E DSPF unit AH C Glass fixing right BF B Table glass EX AA C Screw(516) AH C Glass fixing left BF B White datum glass unit AC C Screw(36) AA C Screw(46) AR C Delivery upper PG SPF AQ D Delivery lower PG AD C Delivery support roller AN C Delivery sponge AH C Delivery support roller shaft 1 AB C Delivery follower spring AC C Screw(38) AC D Stamp cover AA C Screw(46) AB C Screw(38) CB E MFP operation panel CB E MFP operation panel AY D Operation base AA C Screw(48) AC C Dustproof cushion 1 AB C Dustproof cushion 2 AH C Ferrite core(UFR25-12-15) AC C Table glass molt A AA C Delivery PG molt A AC C Delivery PG molt B AB C Delivery PG molt C AC C Delivery mylar AC C SPF glass seal
TR No.
Effective time
[AR-EF3/EF6] [AR-EF5] [AR-EF3/EF6] [AR-EF5] [AR-EF3/EF6] [AR-EF5] [AR-EF3/EF6] [AR-EF5] [AR-EF3] [AR-EF6]
[AR-EF3/EF6] [AR-EF3/EF6] [AR-EF3/EF6] [AR-EF3/EF6] [AR-EF3/EF6] [AR-EF3/EF6] [AR-EF3/EF6] [AR-EF3/EF6] [AR-EF3/EF6] [AR-EF3/EF6] [AR-EF3/EF6] [AR-EF3/EF6]
[AR-EF3] [AR-EF5/EF6]
manuals4you.com
31-1
[ Exteriors[AR-EF3/5/6]
11 29 2
2 3 31 14
11 7 2 5 2 10 32 9 15
2 6
manuals4you.com
30 4
24
26
AR-EF5
12 13 16
15 37 2 33 34 15 23 25
18 17
20 19 21 35 18 18 21
34
27
28
19 2 22 36
20
19 18
35 36 2 22
31-2
AR-EF3/6
FCP09302
PARTS CODE
MARMP0148FCZ2 XBPS730P06KS0 LBSHZ1102CCZZ PSLDH0178FCZZ NSFTZ1805FCPZ XRESP30-06000 MSPRT1563FCZZ LHLDZ1085FCZ2 CPWBF1453FCE2 MARMP0147FCZ2 XEPS730P05000 GCAB-0942FCN1 GCAB-1081FCZZ XEBS730P08000 CARMP0147DS51
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AK C Original detect arm lower AB C Screw(36KS) AC C Rubber roller bushing 1 AD C Original detect shield plate AM C Original detect fulcrum shaft AA C E type ring(E3) AC C Original detect spring AD C Original detect fulcrum holder AX E ORS emission PWB AK C Original detect arm upper AA C Screw(35) AS D Upper cabinet rear AV D Upper cabinet rear AC C Screw(38) BA E ORS emission unit
TR No.
Effective time
[AR-EF3/EF6] [AR-EF5]
501
1
4 9
5 7 8 6 10
12
11
11
13
FCP09303
manuals4you.com
32-1
PARTS CODE
CPWBN1560FCE3 CPWBN1560FCE4 CPWBN1560FCE3 CPWBN1560FCE4 MSPRP3009FCZZ XEPS730P08000 DHAI-3903FCZZ LHLDZ1459FCZZ VVLLM065HB1-1 VVLLM065HB1TR VVLLM065HB1-1 VVLLM065HB1TR LHLDZ1458FCZZ HPNLH0259FCZZ CPWBF1628FCE1 CPWBF1646FCE1 JBTN-0266FCZZ CBTN-0263FC01 CFILW0284FC03 CBTN-0265FC01 CFILW0282FC03 CFILW0283FC03 CBTN-0264FC02 HPNLC0244FCNZ CPNLC0245FC12 LPINS0014QSCZ DHAI-3193FC11 LPINS0014QSBZ PSHEZ4906FCZZ QCNW-0207FCZZ QCNW-0231FCZZ QCNW-0207FCZZ QCNW-0231FCZZ PSHEP5006FCZZ DKIT-0369FCZZ
25
28 701
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK BM E LVDS PWB [AR-EF3] 5 BB E LVDS PWB [AR-EF3][Unleaded solder correspondence][With No.8,25] BM E LVDS PWB [To No.701][AR-EF3] BB E LVDS PWB [AR-EF5/6] AD C LCD earth plate spring AC C Screw(38) AE C ORS PD harness AE C LCD holder B CB B LCD module [AR-EF3] 5 BY B LCD module [AR-EF3][Unleaded solder correspondence][With No.1,25] CB B LCD module [To No.701][AR-EF3] BY B LCD module [AR-EF5/6] AF C LCD holder A BF D Touch panel BA E MFP OPE PWB [AR-EF3] BB E MFP OPE PWB [AR-EF5/6] AK C Change key AN C Ten key AF C C key smoke AF C C key AK C Copy key smoke AH C CA key smoke AN C Copy key AY D Operation panel A AZ D Operation panel B EX-E AF C Fixing pin D AC C Panel earth harness Fixing pin E AF C AC C Touch panel sheet AF C LCD interface FFC [AR-EF3] LCD interface FFC [AR-EF3] 5 AG C [Unleaded solder correspondence][With No.1,8] AF C LCD interface FFC [To No.701][AR-EF3] AG C LCD interface FFC [AR-EF5/6] AE C Panel sheet BZ LCD-INV kit [AR-EF3]
TR No.
CCE272
CCE272
05/05 05/12
CCE272
05/12
33-1
A (701) 1 3 3
3 22 2 (701) 25 3 9 10 A
3 3 7
(701) 8
6 3 22
12 24 13 11 18 14 17 16 15
24 19
28
21 20
21
23
FCP09304
manuals4you.com
33-2
Update : 06/02/27
PARTS CODE
PCOVP1722FCZ1 PCOVP1599FCZ1 XHBS730P04000 QCNW-0217FCZZ QCNW-0209FCZZ QCNW-0216FCZZ QCNW-0232FCZZ QCNW-0167FCZZ PCOVP1761FCZ1 PCOVP1600FCZZ PSHEP4932FCZ1 XBBS730P06000 LPLTM5723FCZZ XHBS740P08000 VHI28F081L40F CPWBX1635DS51 CPWBX1635FCE1 CPWBN1450FCE2 LHLDW1115FCZZ QCNW-0206FCZZ QCNW-0208FCZZ XBBS740P06000 CPWBN1632FCE1 CPWBN1632FCE2 CPWBN1451FCE1 DHAI-3152FCZZ LPLTM5720FCZZ LPLTM5927FCZ1 LPLTM6471FCZZ LPLTM5877FCZZ XHBS730P06000 PCOVP1598FCZ1 PSHEZ5337FCZZ DHAI-3637FCZZ DHAI-3303FCZZ PGUMS0283FCZ1 LDAIU0610FCZZ LRALM0183FCZZ PSHEZ4843FCZ1 LHLDW1007LCZZ LHLDW0595FCZZ LHLDW0429FCZZ LHLDW1264FCZZ LBNDJ0043FCZZ DHAI-3562FCZZ LFIX-0537FCZZ PSHEZ4841FCZ2 LRALM0184FCZZ LX-BZ0004QSPZ PSHEZ0448QSZZ LPLTP5960FCZZ LHLDW1201CCZZ LFIX-0569FCZZ PMLT-1282FCZ1 PSHEP5044FCZZ XHBS740P06000 LFIX-0576FCZZ PGSK-0017FCZZ PSHEP5153FCZZ PSHEP5152FCZZ PMLT-1429FCZZ PSHEZ4842FCZZ
Inter- PRICE NEW PART change RANK MARK RANK AG C Harness cover B AG C Harness cover B AA C Screw(34) AE C CL interface FFC AE C CL interface FFC AH C CCD interface FFC CCD interface FFC 5 AL N C AM AG AF AC AC AG AA AY BV BV BW AD AH AG AA BA BA BF AF AK AF AG AE AC AL AC BP BC AA AE AG AC AD AC AB AD AA AD AD AC AG AB AA AE AA AD AE AD AA AF AF AD AE AC AD C C C C C C C B E E E C C C C E E E C C C C C C D C C C C D C C C C C C C C C C C C C C C C C C C C C C C C C CCD interface FFC Harness cover C Harness cover C Harness fixing sheet 4 Screw(36) Scanner PWB fixing plate Screw(48) Scanner flash unit Scanner control PWB Scanner control PWB Scanner control PWB Edge bushing MFP-OP interface FFC LVDS interface FFC Screw(46) Scanner interface PWB Scanner interface PWB
DESCRIPTION
[AR-EF3] [AR-EF5/6] [AR-EF3] [AR-EF5/6] [AR-EF3] [Unleaded solder correspondence] [With No.34-18,35-41][AR-EF3] [AR-EF5/6] [AR-EF3] [AR-EF5/6]
TR No.
Effective time
05/03
6 7 9 10 11 12 13 14 15 16 17 18 19 20 22 24 25 26 27 28 29 30 31 32 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
06/03 R/C
Scanner interface PWB Stamp interface harness OC fixing plate Dry heater fixing plate SPF interface harness fixing plate Base plate reinforce plate Screw(36) Harness cover A Harness fixing sheet 2 MFP interface cable MFP interface cable Table glass cushion Harness fixing base MB-B rail F Harness fixing sheet 3 Mini clamp(MN-1) Edge holder(EDS2) Wire saddle Wire holder Snap band(SG-130) PNC harness Harness fixing plate Harness fixing sheet 1 MB-B rail R Screw(RED) Screw protect sheet Scanner cable fixing plate SK holder Scanner cable fixer FFC fixing cushion Dust protect mylar Screw(46) CCD FCC fixer Gasket Adhesive sheet 2 Adhesive sheet 1 Protection cushion Harness fixing sheet 2
[AR-EF3/6] [AR-EF5]
[AR-EF3]
34-1
Update : 06/02/27
2 1 2 52 45 17 14 17 11 38 17 2 53 28 11 10 37 25 13 20 25 19 37 25 35 35 18 26 22 20 35
29
6 2
46 44 12 17
7 15
47
49 25 27
49 25 55 29 50
16 39 17 30
48
31
25
25
51
37
43 29 54
36 25 24 40 36
25 41 29 29 43 43 32 43 24 25 34 43 43 43 25 42 FCP09305
AR-EF3/6
25
AR-EF5
manuals4you.com
34-2
PARTS CODE
CDAIU0619DS58 CDAIU0619DS51 LHLDZ1505FCZZ XBBS740P06000 LBSHC0161FCZZ CCOVP1723FC02 CCOVP1541FC02 XHBS730P04000 PCUSU0203FCZZ PGIDM1890FCZZ NPLYZ0399FCZZ XBPS740P06KS0 LFIX-0284FCZZ PMIR-0165FCZZ MSLI-0138FCZZ PWIR-0201FCZ1 PWIR-0202FCZ1 NBLTH0329FCZZ LX-BZ0049FCPZ NPLYZ0338FCZZ XRESP70-08000 LX-BZ0324FCPZ NPLYZ0013QSZZ NPLYZ0005QSZZ NSFTZ2586FCZZ NPLYZ0006QSZZ RMOTS0914FCZZ XBPS730P05K00 XBPS740P16KS0 MSPRT2846FCZZ CPLTM5719FC02 PGUMS0002QSZZ NGERH0027QSZZ XRESP70-08000 LX-WZ0119FCZZ VHPGP3A38//-1 XBBS740P14000 VHPGP1A22LC-1 XBBS740P10000 DHAI-3150FCZZ CPLTM6200DS52 CPLTM6200DS54 CPLTM0031RS51 NBRGC0133FCZ1 XRESP40-05000 LHLDZ1381FCZZ CPWBF1454FCE2 XHBS740P06000 XEPS740P06000 XHBS730P06000 PSHEP5301FCZZ LPLTM6574FCZZ PMLT-1431FCZZ PSHEP5229FCZZ PSHEP5145FCZZ PSHEP5230FCZZ PMLT-1399FCZZ PMLT-1400FCZZ PMLT-1401FCZZ PMLT-1403FCZZ PMLT-1402FCZZ PSHEP5344FCZZ PSHEP5217FCZZ PSHEZ0448QSZZ PSHEP5188FCZZ PSHEP5201FCZZ PSHEP5189FCZZ PSHEP5215FCZZ CHLDZ1446FC31 CSFTZ2586FC31
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK BQ E Lamp unit BF E Lamp unit AC C Wire holder AA C Screw(46) AB C Edge saddle AV D Dark box AT D Dark box AA C Screw(34) AE C Protection cushion AC C CL guide AG C W pulley T AB C Screw(46KS) AC C 2nd,3rd mirror fixing plate F AP B 2nd,3rd mirror AC C Slider AQ B MB wire F AQ B MB wire R AG B Winding drive belt AB C Screw AN C Pulley(36T) AA C E type ring(E7) AA C Screw AL C Winding pulley AG C Pulley AS C Winding drive shaft AD C L pulley BD B Scanner motor AA C Screw(35K) AB C Screw(416KS) AC C Belt tenshion spring AN C Mirror motor fixing plate AL C Protection rubber AH C Mirror motor idle gear AA C E type ring(E7) AA C Washer AH B Photo transistor(GP3A38) AB C Screw(414) AK B Photo interupter(GP1A22LC) AA C Screw(410) AD C MHPS interface harness BV E CCD unit 5 BV E CCD unit [AR-EF3][Unleaded solder correspondence][With BS E CCD unit AC C PF bearing(M8) AA C E type ring(E4) AL C ORS PWB holder BN E ORS PD PWB AA C Screw(46) AB C Screw(46) AC C Screw(36) AB C Harness protect sheet AF C Scanner rack fixing plate AC C Protection cushion AE C Dark box protect mylar AC C Harness fixing sheet 5 AC C Dark box mylar AA C SCN molt A AA C SCN molt B AA C SCN molt C AA C Table glass molt B AC C Table glass molt A AB C SCN mylar AD C Stamp mylar 3 AA C Screw protect sheet AC C Operation section mylar 2 AD C Step screw mylar AC C Stamp section mylar 1 AC C 2nd,3rd mirror unit mylar BC E 2nd,3rd mirror unit AZ E Winder drive shaft unit(Without No.22)
Effective time
05/03
35-1
3 2 1 3 53 5 6 4 6 54 6 6 53 6 52
501
18 19 9 13 20 21 19 19 51 25 22 23 10 10 9 19
12
502
17 22 23 12
7 15 7 8 28 27 29 29 32 21 42
15
19 16
19
41 64 59
39 38 30 62 31 32 33 35 34 64 48 61 58 63 64 60 60 36 65 60 44 56 26 43 26 24 48 62 50 48 57 55 66 46 45 47 49
FCP09306
55 37 40
42
21 46 47 47
24
manuals4you.com
35-2
. Lamp unit[AR-EF3/5/6]
NO.
! ! 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 901
PARTS CODE
RLMPD0702FCZZ RLMPD0658FCZ1 XEBS730P08000 PREFL0172FCZZ XBBS730P12000 LDAIU0619FCZ1 PCUSU0203FCZZ QCNW-0217FCZZ QCNW-0209FCZZ MSLI-0138FCZZ CPWBF1449FC31 PCUSF0334FCZZ LSTYM0261FCZZ LFIX-0545FCZZ CMIR-0164FC01 MSPRP2825FCZZ TLABZ4335FCZZ (Unit) CDAIU0619DS58 CDAIU0619DS51
Inter- PRICE NEW PART change RANK MARK RANK BB B Lamp BA B Lamp AC C Screw(38) AK B Reflector AA C Screw(312) AS D Lamp base AE C Protection cushion AE C CL interface FFC AE C CL interface FFC AC C Slider BH E Inverter PWB AP C Mirror cushion AB C Wire support plate AC C CL read harness fixer AP B 1st mirror AC C Mirror spring AB D HV caution label BQ BF E E Lamp unit Lamp unit
DESCRIPTION
[AR-EF3] [AR-EF5/6]
TR No.
Effective time
[AR-EF3] [AR-EF5/6]
[AR-EF3] [AR-EF5/6]
. Lamp unit[AR-EF3/5/6]
15
2 3 6 8 4 2
14 11
10
7 2
13
9
12
8 6 8
14
FCP09307
11
36-1
Update : 06/02/27
PARTS CODE
PSHEZ4845FCZ1 PMLT-1286FCZZ PCOVP1595FCZZ XHBS730P06000 PCOVP1615FCZZ XEBS740P10000 MHNG-0208FCZZ MHNG-0208FCPZ PCOVP1518FCZZ LPLTM5887FCZZ XHBS740P08000 LFIX-0568FCZZ PTPE-0265FCZZ PCOVP1644FCZZ PGUMS0298FCZ1 CPWBF1594FCE1 LPLTP5743FCZZ XEBS730P08000 MSPRP2830FCZZ PGUMS0296FCZZ NGERR1386FCZZ NGERP1385FCZZ XEPS730P06X00 PCOVP1645FCZ1 PGUMS0299FCZ1 CPWBF1459FCE3 DHAI-3902FCZZ DHAI-3679FCZZ XESS730P08000 DHAI-3161FCZZ XEBS730P10000 VHPGP1A73A+-1 MLEVP0794FCZZ XEBS740P16000 LPLTP6467FCZZ LPLTP6466FCZZ PCOVP1549FCNZ XEBS730P08000 MARMP0243FCZZ PRNGP0090FCZZ LPLTM2573FCZ1 LPLTP5938FCZZ TLABH4847FCZZ PMLT-1293FCZZ PCOVP1686FCZZ LBNDJ0013FCZ1 GCAB-0944FCN2
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AV C OC mat AD C OC cushion AG D Rack cover AC C Screw(36) AE D Length detect cover N AA C Screw(410) BA C SPF hinge R 3 BA N C SPF hinge R [Unleaded correspondence] AE D ICU ROM cover AL C Hinge joint plate AA C Screw(48) AC C Original detect fixer AC C Cover tape AD D F cover L AC C Cover rubber L AR E SPF VR PWB AF C Width detect fixing plate AC C Screw(38) AA C Width detect spring AD C Cushion AE C Width detect rack AF C Width detect pinion AA C Screw(36X) AH D F cover R AH C Cover rubber R AY E SPF PWB BA C DSPF body interface harness [AR-EF3] BB C DSPF body interface harness [AR-EF6] AB C Screw(38) AK C SPF size detect harness AC C Screw(310) AG B Photo sensor(GP1A73A) AC C Length detect actuator AB C Screw(416) AF C Adjust plate R AF C Adjust plate F AW D Upper cover AC C Screw(38) AD C Manual feeding tray arm AA C Ring(E5) AD C ADF MG plate AC C Shading plate N AD D Original read label AC C Protection cushion AH D Base tray cover AE C Cable band BF D Base tray
TR No.
Effective time
06/02
manuals4you.com
37-1
Update : 06/02/27
1 2
4 6
11 11 11
3 6
6 5 9 6 6
12 11
6 6
48
6
12 27 18 30 46 20 43 23 44 29 30 26 30 33 35 49 33 30 11 40 28
18 16 18
10
18
21
17 19 18 22 23
11
21
15
4
34 25 4 29 14
13
18 37 24 6
FCP09308
41
38 42 40
47 6
39
45
manuals4you
37-2
.com
Update : 06/02/27
PARTS CODE
PCOVP1594FCZZ XHBS730P06000 PMLT-1272FCZZ PGIDM2093FCZZ PSHEP5328FCZZ NROLM1499FCZZ NSFTZ2600FCZZ MSPRP3108FCZZ XEBS730P08000 NSFTZ2599FCZ1 XRESP40-06000 NBRGC0136FCZ1 LHLDZ1483FCZZ PCLC-0303FCZZ NSFTZ2678FCZZ NPLYZ0398FCZZ NBRGM0096FCZ1 NBLTH0363FCZZ NROLR1312FCZZ NPLYZ0397FCZZ NROLR1317FCZZ PCLC-0302FCZZ LPLTM5928FCZZ XBBS730P06000 RPLU-0336FCZZ MARMP0284FCZZ XRESP50-06000 XRESP70-08000 NROLR1483FCZZ LSTYM0288FCZZ LHLDZ1485FCZZ MSPRD3002FCZZ MHNG-0209FCZ1 MHNG-0209FCP1 RMOTS0915FCZZ LFRM-1022FCZZ NGERH1477FCZZ PSHEZ4949FCZZ MSPRP3011FCZZ LHLDW1009ACZZ XHBS740P08000 NGERH1476FCZZ NGERH1478FCZZ NBLTH0364FCZZ LHLDZ1486FCZZ NPLYZ0375FCZZ CPLTM5882FC02 LPINS1031HCZZ PCLR-0426FCZZ NROLR1320FCZZ LPLTM5884FCZ1 PCOVP1818FCZZ LPLTM5785FCZZ XRESP20-04000 PMLT-1270FCZZ JKNBZ0141FCZZ LPLTM5889FCZZ PSHEP4846FCZZ LHLDW2101SCZZ LPLTM5929FCZZ DHAI-3281FCZZ QSW-Z0544FCZZ PCUSS0372FCZ1 XEBS740P10000 LHLDZ1484FCZZ VHPGP1A73A+-1 MSPRC3001FCZZ MLEVP0837FCZZ XHBS730P10000 PCUSS0373FCZ1 PSHEP5319FCZZ PGIDH1897FCZZ PGLSP0103FCZZ LX-BZ0931FCZZ PBRSS0209FCZZ LHLDW1426FCZZ MSPRC3269FCZZ XWHS730-05080 PGIDM2110FCZZ
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AG D Roller cover AC C Screw(36) AB C Damper cushion 3 AN C Paper feed PG SPF AD C PS rear mylar AT C Delivery roller M AM C PS support shaft AC C PS support plate spring AC C Screw(38) AW C Separate roller shaft SPF AA C E type ring(E4) AC C Bearing(M6) AF C Paper feed rotation plate AT B Separate clutch AL C Pick up shaft AC C Pick up roller pulley(22P) AC C Bearing AG B Belt(S2M120) AN A Pick up roller AK C Paper feed roller pulley(28P) AP C Separate roller AT B PS clutch SPF AG C Paper feed base plate SPF AC C Screw(36) AS B Pick up solenoid AC C Pick up joint arm N AA C E type ring(E5) AA C E type ring(E7) AS C PS roller SPF AK C CIS stay AC C SP holder F AC C Spring N BB C DSPF hinge L 3 BB N C DSPF hinge L [Unleaded correspondence] BF B SPF motor N AK C Drive frame AC C Gear(24T) AE C Motor sheet AC C Earth plate spring AA C Clamp AA C Screw(48) AD C Gear(35T/18T) AE C Gear(55T/28T/18P) AG B Belt(S2M130) AC C SP holder R AC C Pulley(22T) AN C Drive plate AA C Spring pin AD C Slide collar AQ C Delivery roller SPF AW C Base tray reinforce plate N AC D DSPF interface harness cover AC C MG plate AA C E type ring(E2) AB C Damper cushion 1 AH C Jam release knob AC C Datum plate AD C OC mat mylar R AB C Cable clamp AR C Delivery roller fixing plate AH C SPF delivery sensor harness AY B Delivery jam sensor AD C CIS cushion 1 AA C Screw(410) AC C Open/close holder AG B Photo sensor(GP1A73A) AB C Open/close detect spring N AC C Open/close actuator N AD C Screw(310) AB C CIS cushion 2 AF C White mylar AT C CIS paper guide AV C CIS glass AC C Screw(M3) AG B Discharger brush SPF AC C Mini clamp AC C Follower shaft earth spring AA C Washer AC C PS guide
TR No.
Effective time
06/02
manuals4you.com
38-1
Update : 06/02/27
2 4
6 8 9 7 10
A B
81
80 8
27 14 27 17 12 23 27
C
9 11 13 15 16 12 24 26 17 27 20 21 30 18 19
34 11 22 38 78 24 35 36
A B
11
manuals4you.com
29 82 2 40 2 37 59 47 52 41
17
2 24 27 37 42
31 25 45 33
24 54 27 49 44 46 48 17 50 65 61 62 40 77 41 41 62 68 71 77 67 43 24
29 33 51 2 32 82
2 2 63
55 2 58 39 57 17 27 2 2 72 39 2 57 2 64 72 76 73 75 74 76 2 53 17 56 27 58 2
69
70 41
FCP09309
38-2
Update : 06/02/27
PARTS CODE
LPLTM5891FCZ1 PMLT-1272FCZZ LSTPP0353FCZZ LPLTM6472FCZZ XEBS730P08000 CPLTM5746FC01 CPLTM5746FC01 LPLTM6477FCZZ LPLTM6477FCZZ VHPGP1A73A+-1 PMAGT0072FCPZ RPLU-0347FCZ1 DHAI-3162FCZZ MLEVP0796FCZZ MARMP0248FCZZ MLEVP0804FCZZ LPLTM6456FCZZ LPLTM6456FCZZ PSHEZ5338FCZZ PSHEZ5338FCZZ PSHEP5340FCZ1 PSHEP5340FCZ1 LSTPP0314FCZZ MSPRD2870FCZ1 NSFTZ2659FCZZ LPLTM5932FCZZ XEBS740P10000 MLEVP0797FCZZ MSPRD2879FCZZ PMLT-1271FCZZ PSHEP4937FCZZ PGIDM1899FCN1 MSPRT2863FCZZ LPLTP5748FCZZ XHBS730P06000 XHBS730P06000 LX-BZ0064QSZZ PSHEP5320FCZZ PSHEP5321FCZZ PSHEP5322FCZZ PSHEP5323FCZZ MSPRT2864FCZZ XHBS730P06000 MSPRP2832FCZZ LPLTP7040FCZZ LPLTM7039FCZZ PSHEZ4847FCZZ PSHEP4848FCZZ LPLTP5747FCZZ CPLTM5746FC01 CPLTM5746DS51
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AE C Upper delivery rainforce plate AB C Damper cushion 3 AE C Original stopper AD C Separate pad rainforce plate AC C Screw(38) AE C Separate pad fixing plate AE C Separate pad fixing plate AC C Separate plate AC C Separate plate AG B Photo sensor(GP1A73A) AF C Magnet catch AQ B Gate solenoid AK C SPF paper feed harness AC C Set detect actuator AE C MF gate joint arm AC C Stopper lever AC C Front separate plate AC C Front separate plate AH C Separate sheet AH C Separate sheet AF C Separate mylar lower AF C Separate mylar lower AA C E3 stopper AC C Stopper spring AR C Fulcrum shaft AC C Tray 2 sensor fixing plate AA C Screw(410) AC C PS front actuator AB C PS front actuator spring AB C Damper cushion 2 AB C Fixing mylar AY C Upper transport PG AB C Paper feed plate spring AD C Paper feed plate AC C Screw(36) AC C Screw(36) AA C Screw(38) AC C PS front mylar A AC C PS front mylar B AC C PS front mylar C AC C PS front mylar D AC C Pressure spring AC C Screw(36) AC C Separate assistance plate spring AC C Plate AD N C Plate AL C Separate sheet AB N C Sheet AC C Separate plate AE C Separate pad fixing plate AT E Separate pad fixing plate AS
TR No.
Effective time
ARE805 ARE805
05/11 05/11
ARE805
05/11
ARE805 ARE805 ARE805 ARE805 ARE805 ARE805 ARE805 ARE805 ARE805 ARE805
05/11 05/11 05/11 05/11 05/11 05/11 05/11 05/11 05/11 05/11
manuals4you.com
39-1
Update : 06/02/27
6 6 10 1
A 6 6
34 3 2
34 11 13 8 5 10 14 19 25 24 12 15 16 28 21 22 A 10 34 23 6 26 27 28
702 703 704 705 706 707
6 7 20
17
35
701 708
710 709
11
30 29
31
32
37 39 FCP09310 36 38
39-2
PARTS CODE
CPWBN1567FCE3 CPWBN1458FCE3 XBBS730P06000 PCOVP1813FCZZ PCOVP1593FCZ1 DUNT-7079FC14 LX-BZ0680FCZZ QCNW-0170FCZZ XBBS740P08000 PMLT-1284FCZZ DHAI-3663FC11
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK BN E CIS control PWB BT E CIS control PWB AC C Screw(36) AG D CIS PWB cover N AF D CIS PWB cover N CB E CIS unit AB C Screw AH C CIS interface FFC AA C Screw(48) AE C Interface FFC fixing cushion AK C CIS FG harness
Effective time
2 2 2 2 1 7 8 2 3 2
2 9 7
9 5
2 4
FCP09311
manuals4you.com
40-1
e OC cover unit[AR-EF5]
NO.
4 5 6 7 8 9 10 901
PARTS CODE
MHNG-0218FCZZ LPINS0346FCZZ XJBS740P08000 MHNG-0223FCZZ XJBS740P10000 MHNG-0224FCZZ PSHEZ5357FCZ1 (Unit) DUNT-7440DSZZ
Inter- PRICE NEW PART change RANK MARK RANK AD C OC cover hinge AE C OC cover hinge pin AB C Screw(48) AT C OC hinge L AB C Screw(410) AT C OC hinge R AW C OC cushion BR E
DESCRIPTION
TR No.
Effective time
e OC cover unit[AR-EF5]
4 6 4 6 5
7 4 6 4 5 8 9
10
901
FCP09312
41-1
PARTS CODE
SPAKA6075DSZZ LSOU-0177FCG5 LSOU-0179FCZ5 TCADZ1178FCZZ LX-BZ0787FCPZ SPAKA6697FCZZ SSAKZ0003QSZZ SPAKA6523FCZZ SPAKC6696FCZZ SPAKC6732DS11 SPAKC6696DS15 SPAKA6265FCZZ SSAKA1130QCZZ LX-BZ1000FCZZ LX-BZ1001FCZZ XBPSE40P08KS0 PSHEP5354FCZZ TLABH4847FCZZ
Inter- PRICE NEW PART change RANK MARK RANK AA D RSPF protect sheet 1 AP D Delivery tray T AR D Delivery tray 1 AB D Screw caution card AD C Screw for 2/3 mirror lock BR D Top add AF D Body vinyl bag BN D Bottom add BU D Packing case BS D Packing case BS D Packing case AC D Fusing protect add AA D Vinyl bag(100120) AF C Screw AD C Screw AA C Screw(48KS) AC C Scanner rack sheet D AD D Original read label
DESCRIPTION
TR No.
Effective time
[AR-EF3] [AR-EF6]
6 12 13 14 1 15
7 11
10
8 2
9 FCP09313
manuals4you.com
42-1
PARTS CODE
LPLTM6454FCZZ PCOVP1810FCZZ PCOVP1811FCZZ PSHEP5351FCZZ LX-BZ1014FCZZ JHNDM0176FCZ1 LX-BZ0888FCZZ CCHSM0111FC02 CCHSM0110FC02 PSHEP5353FCZZ PSHEP5352FCZZ XBPSE30P12KS0 JHNDP0160FCZZ NSFTZ2887FCZZ MCAMP0105FCZZ LX-BZ0903FCZ1 XHBSE40P08000 XBPS740P08KS0 XBBSE30P06000 CPLTM6627FC01
Inter- PRICE NEW PART change RANK MARK RANK BA C Rack bottom plate AE C Rack cover right AE C Rack cover left AE C Scanner rack sheet L AD C Screw AQ C Left rack rear handle AC C Screw BM C Left rack upper BL C Right rack upper AB C Scanner rack sheet F AE C Scanner rack sheet R AA C Screw(312KS) AD C Adjust knob AP C Adjust shaft AC C Adjust cam AC C Screw(570) AA C Screw(48) AB C Screw(48KS) AA C Screw(36) AD C Rack adjust plate
DESCRIPTION
TR No.
Effective time
1 5 4 6 7 8 9 14 12 13 3 16 17 18 63 11
15
FCP09314
43-1
Update : 06/02/27
PARTS CODE
RFILN0047FCZZ RFILN0062FCPZ RFILN0063FCPZ RMPTR4103ACZZ RMPTR4103ACZZ RMPTR4103ACZZ RMPTR4103ACZZ RMPTR4103ACZZ RMPTR4330ACZZ RMPTR4330ACZZ VCCCCZ1HH100D VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB222K VCKYCZ1CB103K VCKYCZ1HF103Z VCKYCZ1EF223Z VCKYCZ1EF223Z VCKYCZ1EF223Z VCKYCZ1EF223Z VCKYCZ1EF223Z VCKYCZ1EF223Z VCKYCZ1EF223Z VRS-CZ1JD000J VRS-CZ1JD000J VRS-CZ1JD330J VRS-CZ1JD151J VRS-CZ1JD331J VRS-CZ1JD561F VRS-CZ1JD621F VRS-CZ1JD681J VRS-CZ1JD911F VRS-CZ1JD102J VRS-CZ1JD122J VRS-CZ1JD562J VRS-CZ1JD752J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103F VRS-CZ1JD203J VRS-CZ1JD303J VRS-CZ1JD303F VRS-CZ1JD624J VRS-CZ1JD105J VRS-TP2BD131J VRS-TP2BD151J VRS-TP2BD301J VRS-TP2BD471J VRS-TP2BD561J VRS-TP2BD152J VHDCRH01+++-1 VHDCRH01+++-1 VHDMA704A//-1 VHDRLS73///-1 VHDDA204U//-1 VHDDAN202U/-1 VHDDAN202U/-1 VHDDAP202U/-1 VSDTA143ZUA-1 VSDTC143ZUA-1 VS2SK3018++-1 VS2SK3065++-1 VS2SB1197KR-1 QCNCW1190FCPZ QCNCM7022SC0E QCNCM1187FCZZ QCNCM1167FCZZ QCNCM7022SC0F QCNCM0828FCZZ QCNCW0948FC12 QCNCM7014SC1C
5 6 7 8 9 10
11
12 13 15 16 17 18 19 20 21 22 23 24
25
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 45 46 48 49 50 57 58 59 60 61 62 63 64
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AC C Filter(MMZ1608S121AT) [NF6,NF5] AC C Line Filter(ZJSR5101-102TA-01) [NF1,NF3] AD C Line Filter(ZJSR5101-103TA-01) [NF4,NF2] AB B Block resistor(10K4) [BR2,BR3,BR4,BR5,BR6] AB B Block resistor(10K4) [BR7,BR8,BR9,BR10,BR12] AB B Block resistor(10K4) [BR13,BR14,BR16,BR18,BR20] AB B Block resistor(10K4) [BR22,BR23,BR24,BR25,BR26] AB B Block resistor(10K4) [BR27,BR28,BR29,BR30,BR31,BR37] AB B Block resistor(334) [BR1,BR11,BR15,BR17,BR19] AB B Block resistor(334) [BR21,BR32,BR33,BR34,BR35,BR36] AA C Capacitor(50WV 10pF) [C55,C56] AA C Capacitor(50WV 1000pF) [C15,C16,C21,C25,C26] AA C Capacitor(50WV 1000pF) [C27,C28,C32,C33,C34] AA C Capacitor(50WV 1000pF) [C35,C36,C37,C44,C45] AA C Capacitor(50WV 1000pF) [C46,C47,C49,C50,C82,C88] AA C Capacitor(50WV 2200pF) [C57,C58,C65,C66] AA C Capacitor(16WV 0.01F) [C39,C80,C81,C83,C84] AA C Capacitor(50WV 0.01F) [C3,C17,C18] AA C Capacitor(25WV 0.022F) [C1,C4,C5,C13,C14] AA C Capacitor(25WV 0.022F) [C20,C22,C29,C30,C38] AA C Capacitor(25WV 0.022F) [C40,C42,C43,C48,C53] AA C Capacitor(25WV 0.022F) [C54,C59,C60,C61,C68] AA C Capacitor(25WV 0.022F) [C69,C71,C73,C74,C75] AA C Capacitor(25WV 0.022F) [C76,C77,C78,C85,C86] AA C Capacitor(25WV 0.022F) [C87,C90] AA C Resistor(1/16W 0 5%) [R34,R35,R36,R42,R43] AA C Resistor(1/16W 0 5%) [R44,R53] AA C Resistor(1/16W 33 5%) [R12] AA C Resistor(1/16W 150 5%) [R24] AA C Resistor(1/16W 330 5%) [R5,R9,R91] AA C Resistor(1/16W 560 1%) [R60] AA C Resistor(1/16W 620 1%) [R61] AA C Resistor(1/16W 680 5%) [R67] AA C Resistor(1/16W 910 1%) [R58] AA C Resistor(1/16W 1K 5%) [R10,R18,R39,R40,R57,R93] AA C Resistor(1/16W 1.2K 5%) [R87,R88] AA C Resistor(1/16W 5.6K 5%) [R68,R70,R72] AA C Resistor(1/16W 7.5K 5%) [R25,R51,R52] AA C Resistor(1/16W 10K 5%) [R1,R4,R6,R7,R8] AA C Resistor(1/16W 10K 5%) [R13,R17,R20,R21,R22] AA C Resistor(1/16W 10K 5%) [R23,R26,R27,R28,R30] AA C Resistor(1/16W 10K 5%) [R33,R45,R46,R47,R48] AA C Resistor(1/16W 10K 5%) [R49,R50,R55,R56,R62] AA C Resistor(1/16W 10K 5%) [R63,R64,R65,R66,R69] AA C Resistor(1/16W 10K 5%) [R71,R73,R78,R90,R92] AA C Resistor(1/16W 10K 1%) [R79,R89] AA C Resistor(1/16W 20K 5%) [R14] AA C Resistor(1/16W 30K 5%) [R94] AA C Resistor(1/16W 30K 1%) [R80] AA C Resistor(1/16W 620K 5%) [R31] AA C Resistor(1/16W 1M 5%) [R41] AA C Resistor(1/8W 130 5%) [R82,R84] AA C Resistor(1/8W 150 5%) [R81,R83] AA C Resistor(1/8W 300 5%) [R85] AA C Resistor(1/8W 470 5%) [R74,R75,R76] AA C Resistor(1/8W 560 5%) [R77] AA C Resistor(1/8W 1.5K 5%) [R86] AC B Diode(CRH01) [D15,D16,D17,D18,D19] AC B Diode(CRH01) [D20,D21,D40] AC B Diode(MA704A) [D28] AA B Diode(RLS-73) [D22,D23,D25,D26,D27] AB B Diode(DA204U) [D24] AB B Diode(DAN202U) [D31,D33,D34,D35,D36] AB B Diode(DAN202U) [D37,D42,D2,D10] AB B Diode(DAP202U) [D29,D30,D32,D38,D39,D41] AB B Transistor(DTA143ZUA) [Q10,Q11,Q12] AC B Transistor(DTC143ZUA) [Q2,Q3,Q7,Q8,Q9] AC B Transistor(2SK3018) [Q1] AG B Transistor(2SK3065) [Q13,Q14] AC B Transistor(2SB1197K) [Q4,Q5,Q6] AN C Connector(TX24-100R-LT-H1) [CN1] AB C Connector(S5B-PH-K-S) [CN2] AM C Connector(BM30B-SRDS-G-TFC) [CN3] AP C Connector(BM50B-SRDS-G-TFC) [CN4] AB C Connector(S6B-PH-K-S) [CN6] AE C Connector(S26B-PHDSS) [CN7] AG C Connector(1-171825-2) [CN8] AC C Connector(B13B-PH-K-S) [CN9]
TR No.
Effective time
manuals4you.com
44-1
Update : 06/02/27
PARTS CODE
QCNCM0829FCZZ QCNCM7022SC0C VHPLT1D67A/-1 RCRSZ0001QSZZ RCRMZ6007RCZZ VRS-RE3DA1R0J QSOCZ0095FCZZ QSOCZ0002QSPZ VHIC24WC08L-1 RH-IX0037QSPZ VHIHN58V65A-1 VHIVHC244SJ-1 VHI74VHCT244X VHI74VHC04M-1 VHI74VHC32M-1 VHI74VHCT08AJ VHILM324D++-1 VHILM339D++-1 VHITD62003AP1 VHID62503FG-1 VHIMTD1361F-1 VHIL108733N-1 (Unit) CPWBX1635DS51 CPWBX1635FCE1
Inter- PRICE NEW PART change RANK MARK RANK AG C Connector(S28B-PHDSS) AB C Connector(S3B-PH-K-S) AC B LED(RED)(LT1D67A) AG B Crystal(19.6608MHz) AD B Crystal(4.19MHz) AB C Resistor(2W 1.0 5%) AR C IC Socket(179707-1) AC C IC Socket(8Pin) AF B IC(C24WC08L) AQ B SRAM(IS61LV256-15JL) AW B P-EEPROM(HN58V65AP) AG B IC(74VHC244SJ) AF B IC(74VHCT244ASJX) AE B IC(74VHC04M) AD B IC(74VHC32M) AD B IC(74VHCT08ASJ) AE B IC(LM324D) AE B IC(LM339D) AG B IC(TD620003AP1) AG B IC(D62503FG) AR B Driver IC(MTD1361F) AG B IC(L1087MPX-3.3/NOPB) BV BV E E Scanner control PWB Scanner control PWB
DESCRIPTION
[CN10] [CN11] [LED1] [X1] [X2] [R16,R19] [SOCKET1] [IC23] [IC23] [IC11] [IC20] [IC7,IC8] [IC10] [IC3,IC21] [IC6] [IC2] [IC19] [IC9] [IC4,IC5,IC18] [IC1,IC17] [IC12] [IC14]
TR No.
Effective time
06/03 R/C
44-2
PARTS CODE
QCNCW1001YC40 QCNCW1358FCPZ QCNCW1212FCPZ QCNCW1186FCZZ QCNCW1134FCZZ QCNCM0991FCZZ QCNCM7014SC0D VHDRLS73///-1 VCKYCZ1HF103Z VCEASX1CN476M VRS-CZ1JD000J (Unit) CPWBN1632FCE1 CPWBN1632FCE2
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AH C Connector(IL-FPR-40S-VF-E1500) [CN1] Connector(IL-FPR-40S-VF-E1500) [Unleaded solder correspondence] 5 AR N C [With CPWBN1632FCE2][CN1] AE C Connector(SLD5S-1) [CN2] AF C Connector(TX25-100P-LT-H1) [CN3] AH C Connector(T24FAZ-SMT-TF) [CN4] AG C Connector(30FMZ-BT) [CN5] AB C Connector(B4B-PH-K-S) [CN6] AA B Diode(RLS-73) [D1] AA C Capacitor(50WV 0.01F) [C1,C3] AC C Capacitor(16WV 47F) [C2] AA C Resistor(1/16W 0 5%) [R1,R2] BA 5 BA N E E Scanner interface PWB Scannaer interface PWB
TR No.
Effective time
05/03
901
05/03
manuals4you.com
45-1
PARTS CODE
QSW-P0008QSZZ QSW-P0008QSZZ QSW-P0008QSZZ QSW-P0008QSZZ QSW-P0469FCZZ QCNCW1134FCZZ QCNCM1171FCZZ RALMB1002LCZZ RCRS-0007FCZZ VCEAJU1CW476M VCKYPU1HB101K VCKYPU1EB223Z VHIM34282M1-1 VHPSLR322MC3F VHPSLR322MC3F VRD-HT2EY102J VRD-HT2EY221J VSDTC114YS/-1 VHPLT9400E/-1 (Unit) CPWBF1628FCE1
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AC B Push switch(EVQ23G04K) [0K,1K,2K,3K,4K] AC B Push switch(EVQ23G04K) [5K,6K,7K,8K,9K] AC B Push switch(EVQ23G04K) [*K,#K,CAK,CLK,PRK] AC B Push switch(EVQ23G04K) [FAK,COK,JOK,CUK] AD B Push switch(B3W-1100) [PSW] AH C Connector(T24FAZ-SMT-TF) [CN101] AE C Connector(B6B-PH-SM3-TB) [CN102] AE B Alarm(PKM13EPY-4000-TF01) [BZ1] AD B Crystal(CSBLA480EC8B-B0) [X1] AB C Capacitor(16WV 47F) [C1,C4] AA C Capacitor(50VW 100pF) [C6,C7] AB C Capacitor(50VW 0.022F) [C2,C3,C5] AG B IC(M34282M1-F57GP[KEYCF57]) [IC101] AC B LED(GREEN)(SLR-322MC) [PRT,FAX,COPY,JOB,PONL] AC B LED(GREEN)(SLR-322MC) [ICPDATA,FCOM,FDATA] AA C Resistor(1/4W 1.0k 5%) [R1] AA C Resistor(1/4W 220 5%) [R2] AB B Transistor(DTC114YSA) [Q1] AK B LED(LT9400E) [RPL] BA E MFP OPE PWB
TR No.
Effective time
46-1
PARTS CODE
VHIVHC244SJ-1 VHI87R1150E-1 VHI74VHC04M-1 VHI7SZ125M5-1 VHIVHC240SJ-1 VHIF1117S25-1 VHDD1FM3706-1 VCCCCZ1HH101J VCCCCZ1HH101J VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HF103Z VCKYCZ1HF103Z VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1CF104Z VRS-CZ1JD000J VRS-CZ1JD000J VRS-CZ1JD101J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD181F VRS-CZ1JD222J VRS-CZ1JD511F VRS-CZ1JD561F RFILN0062FCPZ RFILN0063FCPZ QCNCW1160FCZZ QCNCM0880FCZZ QCNCM0923FC12 (Unit) CPWBN1567FCE3
16
17 18 19 20 21 23 24 25 26 27 28 29 901
Inter- PRICE NEW PART DESCRIPTION change RANK MARK RANK AG B IC(74VHC244SJ) BF B IC(208pin_ASIC) AE B IC(74VHC04M) AE B IC(NC7SZ125M5X) AF B Driver IC(74VHC240SJ) AF B IC(F1117S25) AD B Diode(D1FM3706) AA C Capacitor(50WV 100pF) AA C Capacitor(50WV 100pF) AA C Capacitor(50WV 1000pF) AA C Capacitor(50WV 1000pF) AA C Capacitor(50WV 0.01F) AA C Capacitor(50WV 0.01F) AB C Capacitor(16WV 0.10F) AB C Capacitor(16WV 0.10F) AB C Capacitor(16WV 0.10F) AB C Capacitor(16WV 0.10F) AA C Resistor(1/16W 0 5%) AA C Resistor(1/16W 0 5%) AA C Resistor(1/16W 100 5%) AA C Resistor(1/16W 10K 5%) AA C Resistor(1/16W 10K 5%) AA C Resistor(1/16W 180 1%) AA C Resistor(1/16W 2.2K 5%) AA C Resistor(1/16W 510 1%) AA C Resistor(1/16W 560 1%) AC C Filter(ZJSR5101-102TA-01) AD C EMI filter(ZJSR5101-103TA-01) AD C FFC connector(35pin) AF C Connector(26pin) AE C Connector(12pin) BN E CIS control PWB
TR No. [IC3] [IC5] [IC7] [IC4] [IC1] [IC6] [D1] [C11,13,14,15,16,27] [C4655,6971] [C6,12,23,25] [C35,37,39] [C17,22,24,34] [C36,38,60,62] [C15,10,1821] [C2933,4,41,42,44] [C45,56,58,59] [C6568,72,76,79,80] [R9,15,23,38] [R41,46,65] [R2531,40,42,5664] [R13,10,13,36] [R39,4755] [R43] [R4,7,1822,24] [R45] [R44] [NF2,5] [NF1,3,4,6,7,8] [CN3] [CN1] [CN2]
Effective time
manuals4you.com
47-1
SHARP CORPORATION Digital Document System Group CS PROMOTION CENTER Yamatokoriyama, Nara 639-1186, Japan
2006 May Printed in Japan t