Documente Academic
Documente Profesional
Documente Cultură
AN ELEMENTARY STUDY
PREPARED FOR THE USE OF MIDSHIPMEN AT THE U. S. NAVAL ACADEMY
BY
H. E.
SMITH
*
U.
S.
PROFESSOR OF MATHEMATICS,
NAVY
NEW YORK
JOHN WILEY & SONS,
LONDON
:
INC.
CHAPMAN
1914
BY H.
E SMITH,
U.
S.
N.
Stanhope
F. H.
Ipresft
PREFACE.
at the U. S.
THIS book has been prepared for the use of the Midshipmen Naval Academy, and is designed to cover a short course in the subject taken up in the Department of Mathematics and Mechanics preliminary to the work in the Departments of Ordnance and Gunnery and of Steam Engineering
at the
Academy.
In arranging the subject matter many of the methods introduced by officers previously on duty in the Department of
Mathematics have been employed, and the endeavor has been to lead the student to the opening point for the professional work carried on by the other Departments.
iii
360375
INTRODUCTION.
BEFORE beginning
see
what has been discovered by experimenting with test pieces of material and note some of the conclusions arrived at
from the
results obtained in this way. Experiment shows us that whenever a force acts on a body formed of any substance the dimensions of that body are changed. In mechanics all bodies were assumed rigid and the results obtained under this assumption were true, for mechanics taught us to find the action of one body on another or the force transmitted by one body to another, while
strength of material will teach us the effect in the body itself of a force acting upon it. Mechanics showed us that by means
be moved from one point to another, and strength of material will show us that in transmitting the force the substance forming the conveyance
of a piece of material force could
suffers some slight temporary deformation if the force is within certain limits; that beyond these same limits the substance suffers
will
if
The study
by any particular piece of material, finding the deformation caused by transmitting any force, and finding the dimensions of a piece of material in order that it may safely transmit any particular force.
With regard to deformation materials differ greatly, for example, the force which will double the length of a piece of rubber will not apparently change the length of a piece of steel of the same size, though both of these substances are elastic, and each if stretched within limits will return to its
VI
INTRODUCTION.
The original length when the stretching force is removed. force which makes an indentation in a piece of putty will
scarcely affect a piece of lead, but in this case the indentation made will remain in both these substances as they are plastic.
Obviously, then, we must experiment with the different materials and find out some of their physical properties before proceeding with a mathematical investigation.
The
we determine
their physical properties by experimenting with small pieces of them in machines made for the purpose.
Take
steel, for
A pull is applied and we find the test pieces stretch; if we apply pressure the test pieces are compressed. Having applied all sorts of forces we our results and find that the stretching or comprescompare
are tried under different forces.
sion is always of the same amount if the same value of force on unit cube of the steel is used. We also find that up to a
return to
certain limiting value of the force the material will always its original shape when the force is removed, but if
this value
we go beyond
its original
we
shape; in other
words
list
find the piece will not return to it is not perfectly elastic of materials used in build-
for forces
If
beyond
this value.
we go through
the whole
ing and test each kind in the same way we will find that they will all behave in a similar manner, the difference
will lie in the
amount
of deformation for
any force and the beyond which they are not per-
Experimenting further we find the value of this limiting and having it we can compare the various substances as to their usefulness under different
force for the different materials
circumstances.
substance
we continue to experiment, again and again with a single we find that we may apply as often as we like a force less than the limiting one we found, and that the piece
If
INTRODUCTION.
will
vii
always return to its original shape when the force is removed; but when the force used exceeds the limiting one
found,
if by ever so little, and the force is applied and reoften enough the piece will break, though the deformation caused by the first application of the force was too small From this fact we see that to be measured or even noticed.
moved
is
piece of material which will have to in the least greater than the limiting
piece of glass
is
easily
broken by a light blow and is therefore called brittle or into almost any fragile; wrought iron can be twisted and bent is called malleable or therefore and without rupture shape
ductile.
Material which has been melted and cast into desired shapes some parts thaa it does at others, thereby setting up within it internal stresses which are irregularly
cools quicker at
Such castings can be broken by a comparatively blow though they can usually withstand a large pressure. light These internal stresses can be removed by a process called annealing, which consists in heating the body to a red heat and allowing it to cool slowly, thus allowing the particles an
distributed.
opportunity to rearrange themselves. Metals have the peculiarity that if overstrained they harden in the vicinity of the overstrain and this hardening goes on
with time.
finally
Thus a bar which is sheared off while cold will become extremely hard and brittle near the sheared
holes.
if
end, as will a plate in the neighborhood of cold-punched rivet To avoid this, bore the rivet holes and saw the bar, or,
feasible,
Now
we must
that will not break, but in addition we must have material which will not change its dimensions to any considerable
Vlil
INTRODUCTION.
The experiments by which the constants used in this study have been determined were very carefully conducted and are the results of many independent efforts on the parts of many
different scientists.
gation only
will
its
In this work the mathematical investibe touched upon, the experimental part
being beyond
scope.
CONTENTS.
PAGE
INTRODUCTION
CHAPTER
I.
v
3 15
II.
SHEARING FORCE
TORSION
III.
26
IV. STRESS
DUE TO BENDING
34
43 52
V. COMBINED STRESSES
BEAMS VII. BENDING MOMENTS, CURVES OF SHEARING STRESS AND BENDING MOMENTS VIII. SLOPE AND DEFLECTION OF BEAMS IX. SLOPE AND DEFLECTION (Continued) X. CONTINUOUS BEAMS XI. COLUMNS AND STRUTS XII. STRESS ON MEMBERS OF FRAMES XIII. FRAMED STRUCTURES XIV. FRAMED STRUCTURES (Continued) MISCELLANEOUS PROBLEMS
VI. SHEARING STRESS IN
Reinforced Concrete Beams; Poisson's Ratio;
Stress in
61
73 83
94
105
112
123
133
141
Thick
IX
STRENGTH OF MATERIAL.
STRENGTH OF MATERIAL.
CHAPTER
TENSION AND COMPRESSION
1.
I.
two ways
there
is
when
to be motion
between the
parts,
In the first case, force is parts are to be relatively at rest. transmitted from one piece to another and the combination
of pieces
is
dynamics; the second arrangement is called a framed structure, or simply structure, and we must employ
principles of
the
principles
of
statics
in
its
investigation.
In
either
arrangement, any two parts in contact have a mutual action between the touching surfaces, and the effects produced by this action depend in great measure upon the way in which it In any case it tends to change the shape or dimenis applied.
great enough, to permanence the machine or structure must be strong enough in each part to withstand any force to which it may be subjected. If then we can find
if
the force
is
the greatest force that any particular piece of material can endure without breaking or suffering a permanent change in shape we can be sure of its remaining intact for all force within that limit. In the first four chapters we will apply,
separately,
all the different forces to which a piece of material can be subjected and as any piece in our machine or structure may have more than one of these forces to sustain at any
..
.STRENGTH OF MATERIAL.
given instant we will, in the fifth chapter, show the effect of the combined action of two or more of them.
Let us first investigate the effect on a piece of material an external force applied to it, and we will choose for our investigation a straight rod of uniform cross-section and will not consider the force of gravity as acting. We will apply to the end of our rod a pull, F (not sufficient to break or per2.
of
manently change its shape), which, in order that the rod remain stationary, will require an equal pull in the opposite direction at the other end. These forces tend to tear apart the particles of the material, and as the bar remains intact the particles must be in a different condition, relative to each other, from that in which they were before we applied the If instead of a pull we exert a pressure on one end, an pull. and equal opposite pressure must be applied to the other end to keep the bar in equilibrium, and the particles of the material will now tend to crowd together and crush each In both of these cases we have arranged our forces so other. that the bar does not move and they have been taken small
its
dimensions.
Now
as the length of the bar separates the points of application of our forces, there must be some action set up among the particles of
the bar
itself
H
Fig.
1.
Pull
In tension
Pressure
In compression
Fig. 2.
common point of action. Let us now a imagine plane passed through the bar perpendicular to its axis: in the first case (the pull, Fig. 1) our forces would tend
to the other, or to a
to pull apart the two pieces of the bar; in the second (not shown) they would press them together, each piece would tend to move in the direction of the external force acting on it and the amount of this tendency would be equal to that force so that the total action in the bar between the particles on either side of any imaginary section would be equal but
opposite to the external forces applied. The action of all the particles on the right side of any section would be equal to but opposite to the force on the right end, and of those on the
equal to but opposite to the force on the left end. This must be true in order that the bar remain intact, i. e. in
left side
equilibrium.
3.
Stress.
When any
is
set
up
among the particles of a piece of material that piece is said to be under stress, and the external force which causes the
A rod under the action of a pull is said to be in tension, and the pull is the tensile load. A rod to which pressure is applied is said to be under compression,
stress is called the load.
in using the
and the pressure is called the compressive load. Hereafter word stress we will mean the amount of action between the particles in unit cross-sectional area, and will " use total stress" for the action over the area of the whole cross-section. The stress per unit cross-sectional area is sometimes called " intensity of stress" and is equal to the
external force, F, divided by the cross-sectional area, A. forces on one side of the section only are used, so,
The
(stress)
=F
A.
Of course we would get the same result by using the forces on the other side of the section, as the bar must be in equilibrium; they, however, would act in the opposite direction. 4. Now let us see what will happen if we gradually increase the load, F. We know that all materials are more or less
elastic, so as
is
STRENGTH OF MATERIAL.
according as F puts it in tension or compression; and up to a certain value of F, the bar will spring back to its original If we experiment carefully with length when F is removed. any material we will find that there is for it a certain value of
will
F, after reaching which, and then having removed F, the bar be found a little longer or a little shorter than it was
originally; in other words, it will have a "permanent set." " for unit sectional area is called the This value of limiting
It
is
obvious
that no part of our machine or structure must be subjected to a force equal to this, for if it be the piece so used is afterward
unfit to
If
do
its
work.
increasing F the bar will finally break or crush, but at present we are interested only in the elastic limit, the stress for which we will call /, and for several materials its value will be found in the table at the end of this chapter.
we go on
We know
tensile or
F
that any stress, p,
is
equal to
A.
so to find the
unhurt,
is
we put/ =
all
F A
or
= fA.
This
true for
under compression. We will later (Chapter consider XI) long pieces under compression, in which the stress due to bending 'must be taken into account.
for short pieces
In the preceding article we saw that, within the elastic limit, a piece of material would, when the load was removed, After voluminous experiments, return to its original length.
5.
it
or compression of a rod under stress varies directly as the stress, or stress is equal to a constant multiplied by the exThis is known as Hooke's Law, from tension or compression.
its
discoverer.
I,
If
we
let
rod of length
and
called strain,
and we
will
denote
it
by
e;
then
if
p denote
cross-section,
modulus of
found
6.
being a constant found by experiment and called the Its value for several materials will be elasticity.
in the table at the
end
of this chapter,
E =
e
Work Done on
In
will
all
work
is
done, and we
now
how much work is done on a piece of material on which a load is acting. By Hooke's Law p = Ee so that, as we have
equilibrium within the elastic limit, the resistance of the Before the material to the load must equal p per unit area. Now let us apply load is applied the resistance is nothing.
The rethe load very slowly. sistance will increase with the
load from zero to the equal of the final load. It follows that the
mean
is
Work
multiplied equal to force Fig. 3. by the space through which Due to the load, our rod has stretched through the it acts. Hence the work done is equal to one-half the distance x.
final
resistance multiplied
by
x,
or
if
be the
final
load
L
the work
is
equal to
x.
&
*The following graphic method may be clearer: Let the abscissa represent the extensions, and the ordinates the loads
8
causing them.
STRENGTH OF MATERIAL.
When
0,
L =
0,
and
p == Ee, giving us a straight line for the load curve. The work done will now be represented by the area between the load curve, OA, the axis of x, and the ordinate, Ab, representing the final load, L.
Work =
extension
X L =
The following
is
(load)
= pA
= E~ =
Ee
(Art. 4),
(Art. 5).
is
L = pA = AE j=AEe.
The work done by any load L acting through a space dx Ldx
but
or
is
dW =
Ldx,
for
x gives
EA
'
X2
~]
total extension
U
= pA
gives
which as p
as before.
=-
and L
for the
work
9
elastic limit
will
we
also
/=
hence, from the above,
2 f Al 2
orL =fA;
2h
= f- XF.
2h/
This load then does the greatest amount of work that can be done on a piece of material without injuring it.
While stretched, the rod has stored in it an amount of energy equal to the work done in stretching it to its elastic
limit.
is
is
2E
if
quickly
applied
is
much
slowly increased, for, suppose a vertical rod having a collar round its lower end is stretched by a weight falling from a height h upon the collar.
greater than
falling
weight
is
(h
x)
and
this
Lx
We
have then
or the slowly applied load which would stretch the rod to the same extent as the falling weight would have to be con-
10
STRENGTH OF MATERIAL.
Again, if we imagine a load L to be instantaneously applied and to cause a strain equal to x and a load L, slowly applied which would cause the same strain, the work
done
Lx
must equal
Equating we
have
L = 2L
t
Definitions:
STRESS. When due to the load on a body, there is mutual action between the particles on either side of a section through the body, so that the particles on one side exert a force on those on the other side, stress is said to exist in that body, and the intensity of the stress is the force per unit
area of cross-section. area of cross-section.
Briefly, then, stress is force per unit
STRAIN.
the load on
The
it,
ratio of
change of length
in a
body due
to
briefly,
change of
MODULUS OF
ELASTICITY.
The
stress
which
would
Law
held good
I
/load\ - \area/
to
unit strain
/total extension\ I
\original length /
ELASTIC LIMIT. That stress, which if exceeded will produce a permanent change of length; or the maximum stress a material can suffer without being permanently deformed. When a bar is loaded to its elastic limit, RESILIENCE. the work done in stretching it is called the resilience of the bar, and the modulus of resilience is this work divided by the
11
ULTIMATE STRENGTH is the stress which produces rupture. WORKING LOAD is the maximum stress to which a piece
of material will be subjected in actual practice.
STRENGTH OF MATERIAL
12
STRENGTH OF MATERIAL.
subjected is .0005 for unit length. the weight of the rod. (See Art.
Solution:
Stress
E =
7.)
30,000,000.
Neglect
8960
Ibs.
A.
F = = p A =
Ee.
F
E~e
8960
30,000,000
X. 0005
^
1
Sq in
'
"
3.
2,
taking
the weight of the rod into account. Ans. .611 sq. in., or .625 if rod also
4.
suddenly raised.
steel
rod J
sq. in. in
sectional area
and 5
ft.
long
is
in-
under a load of
ton.
What
5. A chain 30 ft. long and sectional area } sq. in. sustains a load of 3900 Ibs.; an additional load of 900 Ibs. is
suddenly applied. Find the resilience at the instant the 900 Ibs. is applied. E = 25,000,000. Ans. 25.992 ft.-lbs.
6.
steel
rod 3|
ft.
long,
sq.
ins.
sectional
area,
reaches the elastic limit at 125,000 Ibs., with an elongation Find the stress and strain at the elastic limit, of .065 in.
the modulus of elasticity, and the modulus of resilience of steel, and express each in its proper units.
Ans.
/ =
50,000
Ibs.
per
in.;
sq.
in.;
.00166; ^E
30,000,000
Ibs.
7.
Ibs.
in.
per sq.
and modulus
resilience
41
per sq.
piston rod is 10 ft. long and 7 ins. in diameter. of the cylinder is 5 ft. 10 ins., and the effective steam pressure is 100 Ibs. per sq. in. Find the stress pro-
The diameter
complete revolution.
E =
30,000,000.
Change
13
8.
position rod 5 ft. long and 2 in. in diameter, without injury, if the proof stress of the metal is 2.8 tons per sq. in.?
E =
4928 ton-ins.
.15 ton-ins., using
Ans.
22
9.
The proof
strain
of
iron
being
TT nrc,
what
is
the
shortest length of rod 1^ sq. ins. sectional area, which will not take a permanent set if subjected to the shock caused
of 36 Ibs.
dropped through 10
ft.,
E =
30,000,000.
tional area,
Find the shortest length of steel rod, 2 sq. ins. secwhich will just bear, without injury, the shock caused by checking a weight of 60 Ibs. which falls through
12
ft.
Modulus
Ans.
11.
E =
30,000,000.
24.05
ft.
brass pump rod is 5 ft. long and 4 ins. in diameter a bucket 28 ins. in diameter, on which is a pressure of 6 Ibs. per sq. in., in addition to the atmosphere, against a
and
lifts
vacuum below
the bucket which reduces the atmospheric is the stress in the rod and the
E =
9,000,000.
in.,
in.
12. Assuming a chain twice as strong as the round bar of which the links are made, what size chain must be used on
if
/ = 6000?
in.
Ans.
13.
The diameter
pressure
is
piston rod is 9 ft. long and 8 ins. in diameter. of the cylinder is 88 ins. and the effective
40
Ibs.
per sq.
in.
What
is
14 and the
STRENGTH OF MATERIAL.
total alteration in length of the rod per revolution?
E =
in.
13,
and
52.5 in.-tons.
15. The stays of a boiler in which the pressure is 245 Ibs. per sq. in. are spaced 16 ins. apart. What must be their diameter if the stress allowed is 18,000 Ibs. per sq. in.?
Ans.
16.
2J
ins.
is
What
the area of the section of a stone pillar carryis 150 Ibs. per sq. in.?
What
is
per sq.
in.
Ans.
2700
18. The coefficient of expansion of iron is .0000068 in. per degree F. An iron bar 18 ft. long, 1 ins. in diameter, is secured at 400 F., between two walls. What is the pull on
the walls
when
34,862
F.?
Ans.
19.
Coefficient
of
A bar of iron is secured between two bars 17,000,000. of copper of the same length and section at 60 F. What are
the stresses in the bars at 200
F.?
Ibs.
E =
expansion of copper
is
.0000095
in.
Ans.
per sq.
in.
20. A bar of iron is 3 ft. long, 2 ins. in diameter. The middle foot is turned down to one inch diameter. Compare the resilience with the original bar and with a uniform bar
of the
same weight.
(1) 1 to 8;
(2) 1 to 6.
Ans.
CHAPTER
SHEARING.
8.
II.
ing shearing
we used
In studyin the
preceding chapter but will apply our force in a different way. To get the proper effect we will slip our rod through holes
4,
and then
the
the the
our
smoothly as though
it
per-
It will
be sheared
Practically this is as near as we can approximate to pure shearing. In theory the two forces, F, should act on either
side of a section of the rod in parallel planes indefinitely close to each other so that their pull would induce no
tendency to turning or bending; then whether we actually sheared the bar through or not, the stress in the bar on one side of the section would be the force F divided by the
area A, of the section of the bar, or, q
It will
is
=F
A.
parallel to the section, while in tensile or compressive stress the direction is normal to the section for this reason shearing
;
is
stress.
by a riveted
good
15
illustration of shearing.
16
STRENGTH OF MATERIAL.
rivet
is under almost pure shear if it closely fits the rivet and the bearing surfaces of the plates are plane. Fig. 5 shows a section and plan of a single-riveted lap joint. The [I distance between the centers of j_>
I
The
holes,
the
rivet
holes
it
is
is
called
the
pitch p,
and
obvious that
along
q,
this
strip
of
plate,
the
shearing stress,
as before, or as
F
it is
equal to
A.
where d
is
SHEARING.
then,
,
17
^
or,
_ I shearing
I
stress
4
"
F
2~A
SF
at center of pin
=
is
The
limiting shearing stress for several materials the table at the end of Chapter I.
10.
given in
for the
as the thrust on a piston rod, etc.; riveted joints the ordinary steam boiler will give us a good example. Fig. 7 is a section through a boiler designed to
any point
Draw the
per-
Now
if
we should
resolve
Fig. 7.
sum of all the horizontal components would be zero. If, however, we take the sum of all the horizontal components on the right half of the ring we will get all the
these square inches, the
which act toward the right; of course those to the left of the diameter A B will be equal but opposite in direction. It will be further noticed that to support these forces we have the boiler material at A and also at B and both these points support equal "amounts, so we can divide the force acting on the semicircle by 2 to get that part which acts at A or 5; or,
forces
18
STRENGTH OF MATERIAL.
the
components of the A which will give the same result. this sum is most Finding readily done by calculus. Take any point on the circumference and let its angular distance from C be 0, then rdd (remembering our strip is 1 inch wide) will be an element of area on which the pressure is s X rdd acting radially and of which the horizontal component is srdO cos 6, and if we integrate this expression
pressure on that part of the ring from
we can take
sum
of the horizontal
to
between the
limits
and - we
sum* of
all
these
H =
Having H, the
sr
z
I
cos Odd
sr
sin
=
=
sr.
on a strip 1 inch wide, the force on a one of pur rivets is found by multiplying strip supported by this by the pitch, or F = psr, so that the shearing stress on
force
the rivet
is
psr
The
all
vertical
components have no
tensile effect at
A, but form
In this connection
we can
remembering that
under
tensile stress,
stants accordingly. thickness of the plate, the sectional area of the metal will
not shearing, and changing our conIf I is the length considered and t the
be
It,
and
if
is
the tensile strength allowed, the resistance must be balanced by the force IF,
so fit
Isr;
or
sr
SHEARING.
If
19
since boilers
are built of plates with riveted joints, divide our result by the efficiency of the joint, strength of joint being equal to the
We have
seen
how
on a rivet
taken out of our plate a piece of metal equal to the diameter of the rivet hole, so that we have left in the strip of plate, to
bear the whole force F, a section whose area is (p d) t, and the tensile the tensile stress on this section must not exceed
strength
of
the
material,
or to
balance;
la~p
/ =
t(p
F
;
d)
joint
is
There is another kind of joint called the butt joint, where a narrow strip of material, or strap, covers the edges of the
20
single-riveted,
STRENGTH OF MATERIAL.
and here
it will
becomes q
F A
used the
in the
shown
SHEARING.
21
Single-riveted
Double-riveted
22
STRENGTH OF MATERIAL.
Equating we have
which gives the pitch where particular plates and rivets are to be used.
In these formulae
p
d
pitch of rivets,
diameter of
rivets,
= number of rows, = limiting shearing stress for rivets, q / = limiting tensile stress for plate, = thickness of plate.
t
14.
When
is
a bar
is
sion there
the angle
BDC =
Let shearing stress along any oblique section. of F then the the force (acting 0, intensity
DB
is
- F
area
0,
DB
if
but the
is
area
DB
BC X
cosec
or
the
Fig. 12
DB
DB
is
F
.
cosec
The component
d
is
F
A
cosec
-cos
= F sin
A
is
cos
=-F- sin
2
(2 0).
This being
resolved per-
F
a tangential force
shearing stress.
cosec
SHEARING.
23
pendicular to
DB
=
it is
F
is-
sin
cosec
= F-sin A
#,
the normal
stress.
When
is 0,
other value of 6
sition.
When
a finite quantity, which proves our propothe normal stress is 0, but increases with
d to a
maximum when
which
is
as
it
should be.
Examples :
wrought-iron plates, 3 ins. wide by J in. thick are What will be lap-jointed by a single rivet, 1 in. in diameter.
1.
Two
is
the pull required to break the joint, if the tensile strength 18 tons per sq. in.? What is the efficiency of the
joint? Solution:
.'.
Area
(plate)
Strength
|
sq.
in.
=3Xi--lXi
=
|
= lsq.
in.
4
18 tons.
/.
Strength
18
27 tons.
Efficiency
of the joint
If it is of
is
|| or
= 66%.
the same material as the plate the force necessary and 2 18 X 22 =to shear it is F = 14.13 -f tons and the 4
4X7
joint
2.
rivet.
ft., is
cylindrical vessel with hemispherical ends, diameter exposed to internal pressure 200 Ibs. above the atmosIt is
phere.
If
/ =
constructed of solid steel rings riveted together. in., 'how thick must the metal be, and
stress in the metal of the ring joint
sr
Solution: e==
= 200 X
12
= .459 in.
24
,.
,
STRENGTH OF MATERIAL.
.,
Longitudinal stress
5
= 7rr
=^
2 xrtq, or, q
10 nr 2 p
7.2
irrt
5rp
1
1
X 3 X 12 X 200 q= 7 X. 459X2240
3.
What must be
950
Ibs.
in.
in
/=
per sq.
Ans.
4.
.533 in.
single-riveted lap joint, plate J in. thick, is under a in. of plate section. Rivets f in. in
What is the shearing stress on the diameter, pitch 1J ins. rivets and the efficiency of the joint?
Ans.
5.
Efficiency
60%.
Two
butt straps, rivets 1 in. in diameter. The shearing strength of the rivets is f the tensile strength of the plates. Find the and the of the pitch efficiency joint.
Ans.
6.
Pitch 4
ins.
Efficiency .7778.
a treble-riveted, double
butt strap joint between plates J in. thick, rivets f in. in diameter, if the tensile stress of the plates is limited to 10,000 Ibs. per sq. in., and the shearing stress of the rivets to
8000
Ibs.
Ans.
7.
What
is
Efficiency 83
ft.
+ %.
diameter
is
cylindrical boiler 8
sq. in.
ins. in
under 100
Ibs.
What per pressure. plates that the stress may not exceed 4000 Ibs. per sq. in.?
Ans.
8.
1J
ins.
is
What
joint between
the pitch of 1-in. rivets in a double-riveted lap Tensile stress 13.2 tons and |-in. steel plates?
in.
What
is
the efficiency of
Ans.
Pitch 3
ins.
Efficiency
71+ %.
SHEARING.
9.
25
The
with double butt strap, with 1-in. rivets. Shearing stress of What is the the rivets is f the tensile strength of the plate.
pitch? Ans.
10.
6.24 ins.
is
In a pin joint (Fig. 6) the shearing stress of the pin the tensile stress of the rod. | Compare the diameters. Ans. Nearly equal.
11.
is
under a
and a compressive
What
and normal
stresses
on a plane making
V2
tons.
Ans.
12.
S.
= 2\/2
N =
0.
What
riveted, double butt strap joint between 1-in. plates, resistance to shearing is f the resistance to tearing?
Ans.
13.
6.77 ins.
What
800
T5
in. in
diameter
and
Ans.
CHAPTER
TORSION.
15.
III.
In Chapters
and
II
we have
tension or compression, and of shearing. In this chapter we will fix firmly one end of our rod and twist it by applying a
turning moment to the free end. This will subject it to torsion, with the effect that any right section will be turned
about
its
center
by an amount depending upon the distance from the fixed end.* The stress between the
tangential stress.
will be parallel to the Clearly, then, torsion is a If before apof shear.
section, or
kind
AB
our
Fio
.
13
parallel to its after the moment axis, will, is applied, be found to have
test
it
piece,
deformed into helix or screw thread, and the point B will at 6. The angle BAb, or <, is the angle of torsion, and is proportional to the radius of the rod. The angle at the center, 6, is called the angle of twist, and is proportional
now be
to the length of the rod. The distance Bb is equal to rd, but it is also equal to l(f>; as (j> is a very small angle, so that
AB
ty; or
<
=~
(1)
site directions, in
might have applied a turning moment to both ends in oppowhich case the section at the middle of the rod (the fixed end as taken above) would have remained stationary, though it would have been stressed as the others.
26
We
TORSION.
have, by experiment, the equation q where q is the stress at the surface and C
27
We
=
is
Ccf)
for torsion,
the modulus of
Ee to hold in tendistortion or torsion, just as we have p sion or compression, <, the angle of torsion, being a measure of the strain. have then two values of </>,
We
(2)
It
is
on any section,
will
be
constant for any stress. This being true, our equation for 6 proves that q varies with r, or if q, q l} q 2 be the stress on
the surface rods of the same length of radii
r l7 r2
,
then
(3)
?=*=?>.
r
r,
r2
This
is
also true
by experiment,
for radii
drawn on any
that the
intent
section remain straight lines after torsion. 16, Let us find the stress in a tube so thin
due to torsion
sectional area.
will
be practically the
If
we
call this
r,
the
mean
and
the
thickness, then the area of any section will be 2 nrt, and the stress on this area will be q.2 nrt, and the moment of
this stress
will
be
q. 2 nrt.r.
applied to
(D
Now
which
putting this volume of q in equation (2) of Art. 15, is true for either hollow tubes or solid rods, we have
IT
(Values of
at
end
of
Chapter
I.)
28
17,
STRENGTH OF MATERIAL.
Let us
now
Let
must be
internal
considered.
be
its
external
and
r2
its
radius (Fig. 14), and let q equal the stress at a distance r from
Call q l the
maximum
15,
Art.
Fig. 14.
ri
The element
of area at a distance r
it is
is
q. 2
nrdr,
=
ri
>
maximum
on the element
is
r,
.2
moment
of this stress
.2 7ir
dr or
if
r,
which
will
moment
of the resistance
rt
Knowing T
If
this gives us q^
=
if
r2 <)
is solid,
now
r2
0;
or in other words,
the tube
18. It is clear that if we give to q the limiting value for the material, we can find the diameter of the solid rod that This formula is used to will carry a given twisting moment,
{
TORSION.
29
Let a be the design shafts to transmit a given horsepower. length of the crank arm, and F the mean force acting on it
during a revolution; then the mean twisting moment is equal to aF, and the work done per revolution is equal to aF.2 TT (care must be taken to use the same units throughout).
The
energy
of
the
machine
per
is
revolution
is
H. P.
33,000
N
horsepower and
This
is
foot-pounds, where H. P.
the indicated
N the number of revolutions per minute. work done per revolution, and if divided by The mean twist2 n will give the mean twisting moment. is less than the maximum moment twisting moment, ing but the shaft must be designed to carry the greatest, which
also the
is
T =
KTm
'
We
We can get the ing stress allowed for q and solve for r. if moment we take the force greatest twisting acting on the
piston, through the piston and connecting rods to the end of the crank, when the crank is perpendicular to the connect-
ing rod, and multiply this by the length of the crank, remembering that the force acting along the connecting rod is the force acting on the piston multiplied by the secant of the
makes with the connecting rod. and hollow shafts, let the radii of the hollow shaft be r^ and r2 and that of the solid shaft be r; then if T is the resistance offered by the solid shaft and
angle the piston rod
19.
To compare
solid
*q
T _^ 2 r
*
1
(r '
\
<
r2 <)
3
"2 _r ~r
4
l
xqr
r/
same
material.
30
STRENGTH OF MATERIAL.
if
Now
or r
same nr 2 = n
(r
r2 2 )
= Vrf
substituting
Il
nearer r, approaches r n or the the hollow shaft becomes, always retaining the same sectional area as the solid, the nearer the ratio of strength of hollow to strength of solid would that
which
shows
the
of
approach GO. There is, however, a limit to the thinness of our shaft, as it must be able to support its own weight without buckling. If we assume that the ratio of the radii of the hollow shaft is as 2 to 1, and that the sectional areas
are equal,
we
T
get
1.44, or the
hollow shaft
is
nearly
half again as strong as the solid one under these conditions. 20. Substitute in equation (2) of Art. 15 the value of q
found in Art. 17 for the solid shaft, and we get the angle of
twist
=
for a solid shaft.
If
2 Tl
we use
2TI
Now if T is known and 6 can be measthe value of C; or, if C is known and find we can ured, find can we T, and thence the horsepower that a measured,
rotating shaft
is
transmitting.
TORSION.
31
Examples :
What must be the diameter of a shaft to transmit a twisting moment of 352 ton-ins., the stress allowed being tons per sq. in.? What H. P. would this shaft trans3 mit at 108 revolutions per minute, the maximum twisting of the mean? moment being
1.
Solution:
= 2T
Trr
3
or r 3
= 2T =
nq
8
ins.
2X352X7X2 22
X7
64.
.'.r
ins.;
=
P.
_55 ~36
H.
'
33,000
12
N X In X
352
2240
2
7
X 108 X 33,000 X 12 X
2240
X X
22
55
36
Find the size of a hollow shaft to replace the preceddiameter to be I the interior. What is the exterior ing, saved in a steel shaft 60 ft. long? (Cu. ft. metal of weight
2.
steel
480
Ibs.)
Ans.
5.284.
Exterior
diameter
8.454
Ibs.
ins.
Interior
diameter
3. Find the diameter of a solid shaft to transmit 9000 H. P. at 140 revolutions per minute, the stress allowed being 10,000 Ibs. per sq. in., and the maximum twisting moment I the mean.
Ans.
14.5695
ins.
4. Find the size of a hollow steel shaft to replace the above, 9 What is the internal diameter being T s of the external.
saving in weight for 60 ft. of shafting? External diameter = 15.091 ins. Ans.
Internal diameter
8.4886
ins.
Ibs,
32
STRENGTH OF MATERIAL.
5. Compare the strength of a solid wrought-iron shaft with a hollow steel shaft of the same external diameter, the in-
ternal diameter of the steel shaft being \ the external that of iron.
and
length. They contain the same amount of material. pare their strengths when used separately.
Com-
Ans.
7.
As 3
is
to \/2.
is
The
Ibs.
At 95 revolutions per minute what will be the 44,000 on each shaft? What is the H. P.? moment twisting = Ans. T 360 in.-tons. H. P. = 2432.
8.
The pitch
ing
moment on
is
of a screw propeller is 14 ft.; the twistthe shaft is 120 ton-ins.; the mean diais
15 ins.; coefficient of
bearing.
Ans.
9.
Thrust
4^ tons.
98t%.
1
The angle
ft.
of torsion of a shaft
not to exceed
for
each 10
of length;
what must be
its
moment
of 16,940 ft.-lbs.?
(7=10,976,000
Ans.
10.
in.-lb. units.
*=
221
I.
Diameter = 6
ins.
the
the mean, what maximum twisting moment ? in shaft mum stress (torsion) the
is I
is
the maxi-
Ans.
20,000
Ibs.
per sq.
in.
TORSION.
11.
If
is
33
the greatest stress to which a shaft should be subthat the angle of torsion may not exceed 1 for each jected 10 diameters of length?
what
Ans.
12.
tions
is
In changing engines in a ship, the number of revoluincreased J; H. P. is doubled; the ratio of maximum
;
twisting moment is changed from f to of material of the shaft is 25% greater. strength relative size of the new shaft?
to
mean
and the
is
What
the
Ans.
13.
in.
The same
size.
Find the angle of torsion of a steel tube, 6 ft. long, thick; mean diameter 12 ins., shearing stress allowed
in.
Ans.
0.0478,
CHAPTER
BENDING.
IV.
is one more way in which we can introduce stress and that is by bending it. If we rest our rod on supports at its ends and load it at its middle, it will bend into
21.
There
a curve.
ing
The plane
of this curve
is
(OABO,
Fig. 15).
The
particles
Fig. 15.
the rod will tend to crowd together and will be in compreson the convex side will tend to pull apart and
will
be some intermediate
plane, perpendicular to the plane of bending, where there will be neither tension nor compression, a plane of no stress. This
plane
is
The
neutral line
is
the
intersection of the neutral surface with the plane of bending, and it gives us the curve into which the rod bends, and is
The
intersection of the
neutral surface with any section of our rod perpendicular to In Fig. 15, its axis is called the neutral axis of that section.
the lines
AO
and
BO
meet,
34
BENDING.
tion.
35
AOB
is is
surface.
AB
CEFD is the neutral the plane of bending. is the neutral line or elastic curve; and if
HH
AB, then
GK
is its
all
but after bending these same sections (assuming that they remain plane) will be inclined to each other, being nearer together on the concave side,
the
If
is
the the
curvature
of
neutral line
AB
(Fig.
16), 6
any
the
two
sections,
and
the
distance
from
neutral plane to any point in the rod, then the length of the elastic curve between
these two sections
is
Fig. 16.
R6, and the length between these two which are at a distance y
is
(R
y) 0, or
Rd
yd, so that
yd change distance y from the neutral surface. The change of length unit is the total divided length change per by the original
length, or the strain
is
the
total
of length
=
Rd
From Chapter
I,
Art. 5,
we have the
Hence
p
hi
strain
P
.
=7-, or the
36
STRENGTH OF MATERIAL.
as the distance from the neutral surface, outer surface in the plane of bending
must be less than /. 23. We have above our formula for the fiber stress, but do not know what value to use for y, as where the' neutral axis Neither do we know the length of R. We lies is not known. will first prove that the neutral axis of any section of a beam
We know passes through the center of gravity of the section. that the stress is maximum compressive at the surface on the
concave
side; decreases
it is
surface, where
and
in-
creases to a
The
of the
rod
is
in equilibrium, a
that the
sum
horizontal components of all the forces acting must equal Now the loads which cause the bending are all vertical, zero.
so
can
have no horizontal
are
at
the
horizontal
their
17
sum
the
zero,
on
the
opposite
sides
being
stress
equal
Fig. 17
shows the
of
on one
Let
AB
be the neutral
The formula p =
E R
y gives us
the stress per unit area on any element of area, dA, which is throughout at a distance y from the neutral axis. The stress
on the element
is
then pdA, or
E R
yd A.
If
we
integrate this
stress
between the limits for our section, we will get the total on the section, which we know to be equal to zero, or
H = -JydA=0.
**
limit
E r
11 "* 1 '
(1)
BENDING.
37
Now the value of the integral, yd A, divided by the area of the section will give us the distance of the center of gravity of the section from the line AB, and if this distance were zero the line would pass through the center of gravity of the
section.
Now equation
(1)
equals 0;
axis always passes through the center of gravity of the section. Our rod is in equilibrium, one 24. Determination of R.
of the laws of
which
is
that the
sum
of the
moments
,w
of all the
forces
about any axis must equal zero. axis we will take the neutral
moments.
We
the
the
sum
of
moments
of the external
let
forces.
In Fig. 18
AB
be
the rod of length /, loaded with pounds in the middle, so that the supporting forces are
each
then to the
left of
the section
HH
the
moment
of
W
is
W
x;
of the forces
Wx
T'
the same value as before.
The moment
the
beam on
left of
direction of motion of the hands of a watch, while that to the right tends to turn the right part of the beam in the opposite
direction; therefore,
if
we
call
the
first
As in the other cases of equilibrium we negative. will use the values found on one side only of the section. In
other
is
38
this case, the
STRENGTH OF MATERIAL.
moment
of the external forces about the neutral
axis
is
we
will
designate
by M,
so
M=
Wx --
tion
must balance
moment of the stress in the secthe moment of the external forces about the
shows enlarged the part
the
left of
neutral axis.
Fig. 19
of the rod to
the section.
We
moment
of the
direction indicated
by the
while
arrow
the
Fig. 19.
marked
(1),
moment
of the stress in
in
arrow
(2),
and
moments must be
is it
As
on the area dA
moment
is
H ydA.y,
ft
The
/limit
integral f\fd A
between
the
moment
about
the
and we
will designate it
is
by
/,
so that
moment
equal to
E /. R
This
must equal
so
W
-=
/,
or
R=
V
I.
In Art. 22
we found
E=p _, R y
so
we now have
PME
BENDING.
In which
39
stress at
M
/
bending moment at any section due to exterof inertia of the area of the section
= moment
R = E =
25.
about the neutral axis; radius of the arc into which the rod
is
bent;
rod in
have now seen the effect of applying forces to our the different ways. If the stresses caused have the same line of action, that is, if they act on any section in the
all
We
same or 'in a diametrically opposite direction, sum will give us the total stress on the section.
their algebraic
For example,
the stress due to several longitudinal loads is the algebraic sum of the loads divided by the area of the section; or, if a rod is under a tensile stress and there is also a fiber stress due
to bending, the maximum stress would be at the convex surface and equal to the sum of the two stresses, while at the con-
cave surface, which would be in compression due to the bending, the stress would be the difference between the two,
and would act in the direction of the must be considered in actual practice
:
greater.
Another fact
if
changes, a free rod expands or contracts without stress, but the rod be prevented from expanding or contracting, stress
is
The method of taking the algebraic sum when produced. the lines of action are the same is called the principle of
superposition, which may be stated as follows: The effect due to a combination of forces is equal to the sum of the effects due to each force taken separately.
When
line of action,
the stresses caused by our forces have not the same such as combinations of shearing or torsion
with bending, we must arrive at their maximum effects in some other way. In the next chapter we will endeavor to show how to find the maximum stress together with its direc-
40
tion,
STRENGTH OF MATERIAL.
stresses
which is due to the combined effects of two or more which act at right angles. We will then be able to combine the effects of any of the forces which we have applied
We will separately to our rod in these first four chapters. find that the maximum stresses due to any of these combinations are greater than any of the stresses acting singly, and that they act on planes which are inclined to those on which
of the single stresses act. This will account for the apparently erratic manner in which material sometimes carries away; so in deciding if a single part of a machine or
any
structure
forces
it
must
if it
first
find
to
what
Examples
1. A beam 2 ins. wide by 3 bending moment of 72 ton-ins.
ins.
deep
is
is
subjected to a
What
the
3
maximum
fiber
stress?
Solution:
M
P-'
My
72
y --j
1
y=2X
3
=i2
Ah
=2-
p -
~2irr
=24tons
2.
An
iron
flanges 4 ins. by 1 in., and web 8 ins. by \ in. greatest central load it can carry if the stress
What
is
is
the
limited to
y.
M max =
552
WX
5.
3 ft.-lbs.
=W X
36
in.-lbs.,
_ l=.y-
4_TFX36X3 =
=
=
5X36X3
BENDING.
3.
41
ins.
cast-iron
ins.
by
1 in.
bot-
tom
by 2 ins.; web, trapezoidal, J in. thick at 1 thick in. at bottom; total depth of beam 16 ins. and top Find the position of the neutral axis and the ratio of maxiflange 8
mum
is
Ans.
3 to
4. 7.
ins.
from bottom.
Ratio
to
A wooden beam of rectangular cross-section is 15 ft. If the maximum bending moment is and 10 ins. wide. long 16.5 ton-ft., and the allowed stress is \ ton per sq. in., what is
its
depth?
15.4 ins.
Ans.
5.
is 25 ft. long, top flange 3 ins. by 2 ins.; flange 10 ins. by 3 ins.; web 12 ins. by 1 in.; total depth 17 ins. If the stress is limited to 4J tons per sq. in., find the greatest central load it can support in addition to
An I-beam
bottom
its
own weight
Ans.
6.
(take weight of
beam
its center).
6.48 tons.
is
What
rod of iron 2
Ans.
7.
ins. in
diameter
10 ins.
is
may
E =
R =
13,000 ton-ins.
270
ft.
spar, 20
ft.
long,
tains a
stress
maximum
bending moment
what
is
the diameter of
What
sq. in.?
is
^-in. steel
wire
may
ft.
per Ans.
(E for
steel wire
111J
42
9.
is
STRENGTH OF MATERIAL.
rectangular
beam
12
ft.
supported at the ends. Stress is limited to 3 tons per sq. in. Find the load which can be carried at the center; also
find the load
if
the
beam
lies
the
flat
way,
i.e.,
3 ins. deep
and
ins.
wide.
1st case
Ans.
10.
Find the breadth and depth of the rectangular beam of strength which can be sawed from a log 2 ft. in diameter, and compare its resistance to bending with that of
maximum
beam
2
-ft.,
2\/2
Ans.
Top
is
V3
1.
depth
is
=-
ft.
Resist bending in
A/3
ratio of 1.089 to
11.
steel
I-beam 30
ft.
web 24
is
ins.
by
.5 in.; carries
the
maximum
16,000
fiber stress?
Ans.
12.
Ibs.
per sq.
in.
Compare the
and when
4.6 to
laid
by 1 on its
in.;
web 8
ins.
by J
in.,
when up-
side.
Ans.
13.
1.
round
stand a bending moment of 6 ton-ins. length of such a rod which will just carry
CHAPTER
V.
COMBINATION OF STRESSES.
26. In a rod suffering tension and shear let (Fig. 20) be any section which has normal stress due to the tensile load, Let the square shown F, and tangential stress due to shear.
HH
represent the base of an elementary cube of volume, whose height dz is perpendicular to the plane of the paper, and on whose faces dydz are the stresses P and S as shown. It is
44
27.
stress,
STRENGTH OF MATERIAL.
We
can now find the plane on which the resultant due to a number of stresses acting in planes at right
angles, is a maximum. Fig, 21 is, enlarged, the elementary cube of Fig. 20, with the additional stress lf acting so as to
it
in
vertical
tension.
AB
and
let
the
sum
____> c w
of the
plane,
when
resolved
| pi
on the other side would give equal and opposite components to N and T (equilibrium). So that our cube is now in equilibrium under the stresses shown. Let us resolve these stresses horizontally and vertically, then the sum of both the horiFor zontal and the vertical components will be zero. example, the intensity of the stress P on AB is P sin a,
stresses
The
of
AB
X
cos
sin
cosec a.
of the inclined plane is the area (See Art. 14.) Resolving then
we have
N sin a +
N
cos
T T
a a
P sin a P cos a
l
S S
and
2
cos
sin
(2)
a.
= =
get
sin
(1) horizontally.
(2) vertically.
Eliminating
N =P
Reducing
1
T between sin a + P
2
(1)
we
cos a
+
1
a cos a
a.
(3)
cos 2
a a
(sin 2
cos 2
and 2
cos 2
sin
a cos a
sin 2
a
j
+S
sin 2 a.
(4)
COMBINATION OF STRESSES.
45
By
the same
method we get
T =
(4)
P -
Pi - sin 2 a
+ S
cos 2 a.
(5)
to
and (5) give us the stresses along and perpendicular any plane due to the combined stresses P, P l and S.
first
and a or T and a
for
in (4)
is
and
(5) will
N
a
which
N
=
or
maximum
-
minimum.
-- -- 2 sin 2 a
2
da
gives
cos 2
tan 2 a
7/T7
= JL =
=
da
gives
or
tan" 1
A-+
2
(6)
2 cos 2 a
sin 2
tan 2 a
p _ p
-^-^
or
D _
i
E)
i-
_
_
.
tan'
-^-i^+
(7)
28. Equation (6) gives us the angle with P of a plane on which the normal stress due to the combined load is a maximum (the plane 90 from it giving the minimum), and equation (7) the angle with P of a plane on which the tangential stress due to the combined load is a maximum (minimum 90 from it). Obviously, from these equations, the two planes are at 45 from each other (tan 2 a being in one case the negative reciprocal of what it is in the other), or the planes of maximum normal and maximum tangential stresses lie at angles' of 45 with each other. Equation (6) shows the maximum and minimum normal stresses to be at right angles, and if we substitute the value of 2 a found from it, in equation (5) we find that on this plane of maxi-
46
STRENGTH OF MATERIAL.
is zero
normal stress the tangential stress is zero, or the shear when the normal stress is a maximum. The normal stresses found in equation (6) and acting on planes at right angles are called principal stresses and their directions prinIf
mum
cipal directions.
we
Principal stresses are always at right angles. substitute in equations (4) and (5) the values of
a, obtained
sin 2
a and cos 2
from equations
(6)
and
(7)
respectively,
we
will get
the
maximum
and tangential
stresses.
andT 7
COMBINATION OF STRESSES.
any point
(C, Fig. 22), represent respectively
47
the intensity
on a plane making the angle a with P. The radius vector, OC, represents on the same scale the amount and direction of the resultant intensity of stress
of the stresses
and
,'
Fig. 22.
the eccentric angle <fi is x = P cos <, and y = P l sin <p. Now the tangent of the angle d, which the resultant stress makes with the direction of P, is
The equation
tan
y = P, =x
sin
cos
P P
cos
sin
a a
P P
tan
P -P
l
,
cot a.
the resultant stress, is equal to \/ x 2 + ?y 2 and the is angle the resultant stress makes with the plane Had there been another normal stress at right (0 + )
72,
AB
and P the locus of the end of the would have been the surface of an ellipsoid.
probably as easy to find the resultant of and then get the resultant of the third
is
In this case
it is
two
with
of the stresses
it.
This ellipse
amount
of the resultant of the principal stresses, or the binations of other normal stresses, which may be done
com-
graph*
48
ically as follows:
STRENGTH OF MATERIAL.
and Draw the axes (Fig. 23) and With lay off to the same scale P on OX, and P l on OY. these distances for radii, describe two concentric circles
with centers at 0.
OX
OY
Draw
the line
AB, making
the given
angle a with
and draw
OD
lt
draw
FC
parallel to
OX.
last
the
CE
represents the
due to P resolved on the plane AB, and OE represents the stress due to P l resolved Fig. 23. on the plane AB; while OC the resultant stress on A B due to both, and the represents
stress
angle
30.
a into three be resolved (Art. 14) simple body may always stresses acting on planes at right angles. By means of the formula of Arts. 27 and 28, we can always calculate the value and direction of the resultant stress on any
plane due to these three simple stresses, and by means of the stress ellipse of Art. 29 we can calculate or determine graphically the amount and direction of the result-
COB is the angle it makes with the plane A B. Now any condition of stress at any point within
ant of two simple normal stresses on any given plane. For example, if we find a piece of material under tensile
stress
combined with
(8)
torsion,
we can
substitute for
in
equation
surface
(maximum) due
-
and, unless
another stress at right angles to the plane of these two, P l The value of N given by these substitutions is the is zero.
maximum normal
stress,
it
acts will
COMBINATION OF STRESSES.
49
be found by making the same substitutions in equation (6), remembering that a is the angle the plane makes with the
direction of the tensile stress P.
maximum
fiber
stress
always use the maximum values, for the piece of material must be strong enough to sustain the greatest stresses to
which
it will
be subjected.
Example 5, at the end of this chapter, offers a tration of the use of the stress ellipse.
Examples
:
good
illus-
1. The shaft of a vessel, 15 ins. in diameter, is subject to a twisting moment of 100 ft.-tons and a bending moment of 20 ft.-tons, also the thrust of the screw is 16 tons. Find
the
maximum
:
stresses
on the
shaft.
Solution
"
1
"
2~~
'
or
N
2
(N
/.
P)
=S =
and T 2
=S + P
2
2
.
nd A = -4
thrust
16 Ttd
2
64 -
nd 2
My _
64
64
q (torsion)
= S = Fa
(twisting
moment)
64
X
?rcP
20
nd
Te
50
2.
STRENGTH OF MATERIAL.
tube, 12 ins.
J in. thick,
is
acted
of 25
on by a thrust
ft.-tons.
of 20 tons
What
are
their
angles? Ans.
3.
39|.
sq. in.
sq. in.
and
tensile stress,
What
are the
maximum
Ans.
4.
The thrust of a screw is 20 tons; the shaft, diameter 14 has a twisting moment of 100 ton-ft. and a bending ins., moment of 25 ton-ft. Find the maximum stress and compare
it
with what
or thrust.
it
moment
Ans.
5.
At a point within a
stresses
cipal
and 171
Ibs.
Find the
amount and
making an
angle of 27 with the 255 Ibs. stress. Ans. 191.35 Ibs. 79 46' 20".
6.
A beam
is
under a 300-lb.
tensile stress
and a
100-lb.
Find the normal and tangential stresses on shearing stress. a plane making an angle of 30 with the tensile stress.
Ans.
7.
Normal
161:5;
in.
Find the principal stresses and their directions for a beam which is under tensile stress of 400 Ibs. and shearing stress of 250 Ibs.
point in a
Ans.
- 25
8.
120;
X =
in
Find the maximum and minimum values of the shear example 7 and their directions.
320
Ibs.
Ans.
per sq.
in.
X =
19
19'
48"; 109
19' 48".
COMBINATION OF STRESSES.
51
0. A bolt, 1 in. in diameter, is under a tension of 5000 Ibs. and a shearing force of 3000 Ibs. Find the maximum stresses and their directions. Ans. N = 8155; T = 4970 Ibs. per sq. in. Angles are N 64 53', and T 19 53' with axis of bolt.
Find the maximum stress in a shaft 3 in. in diameter ft. between bearings, which transmits 40 H. P. at 120 revolutions per minute, and has a weight of 800 Ibs. half way between bearings. The shearing stress due to above arrange10.
and 12
ment
is
4000
Ibs.
per sq.
Ibs.
in.
Ans.
11.
N =
What
7600
and T
4900
Ibs.
per sq.
in.
is the diameter of a steel shaft to transmit 90 250 revolutions per minute, the distance between bearings to be 8 ft. and a load of 480 Ibs. to be carried half way between bearings? The allowable maximum stresses being 7000 Ibs. for N and 5000 Ibs. for T (shearing force due
H.
P. at
Ans.
12.
=2.8+
ins.
in.
(about 3
ins.).
steel
thick,
and 8
bar of rectangular section, 18 ft. long, 1 in. deep, is under tension of 80,000 Ibs. and a
Ib.-ins.
What
is
the
maximum
per sq.
in.
is
13. A wooden beam, 8 ft. long, 9 ins. deep, and 10 ins. wide, under compression of 40,000 Ibs. and a bending moment of
Ib.-ins.
48,000 Ans.
What
Ibs.
is
the
maximum
stress?
804J
per
sq. in.
CHAPTER
VI.
we can change
the value of the twisting moment only by varying the amounts of the forces forming it or by changing the length of the arm; but to get the stresses due to bending and shearing
we can apply
loads in a
number
of different ways.
have also been neglecting the action of the force of gravity on our rod, which is of importance, as in the case of large shafts or beams whose bearings or supports must be
spaced with reference to their weights; besides the supporting forces' for a beam loaded in any way must be known in order
to find the shearing and bending stresses. 32. Obviously, as we have assumed in Chapter IV, the supporting forces for a weightless, horizontal beam, loaded
We
its
W
t
or half
the load; if, however, we take into consideration the weight of the beam and put several loads upon it at different places,
the conditions of equilibrium require that the sum of the moments of all the forces acting on the beam about any axis
must be
of the
zero.
beam and the supporting forces, all acting in the same plane.* If we take moments about an axis through one of
* If the forces do not all act in the same plane those acting in one plane may be considered separately, and the resultant of the several supporting forces in the different planes found. The supports, however, must be strong enough in the directions of each of these planes to sustain the forces acting in those planes.
52
53
the supports, the moment of that supporting force will be zero, and the other suporting force, being now the only
unknown
algebraic
it is
sum
quantity, is readily found by equating to zero the of the moments of all the forces; for example,
beam 20
ft.
carrying 150
Ibs.
ft.
from
and supported
from the
Fig. 24).
left
end; and 750 Ibs. 16 ft. from the left end (see The weight of the beam is 200 Ibs. and acts at its
150 Ibs.
300 Ibs
750 Ibs
Fig. 24.
which in this case is at the middle of the beam. If we take moments about an axis through the left end of the beam, we eliminate the supporting force P, whose moment about this axis is zero; our equation for equilibrium will then be
center of gravity,
200
10
150
300
11
750
16
-QX
20
0,
from which Q = 910, and P is obviously the difference between the sum of the weights and Q, or P = 490 Ibs^ In the above the weights act at the points indicated and are known
is
If the loading is continuous the effect considered as acting at the center of gravity, as it has been taken for the weight of the 'beam in the above.
as concentrated loads.
33. Having the supporting forces, we can now find the Refershearing stress on any transverse section of a beam. ring to Fig. 25, and at first considering the beam weightless,
if
HH
is
force
and the
54
first
STRENGTH OF MATERIAL.
load
W^
parts of the
beam
,
there would clearly be a tendency for the two to move as shown, the left part remaining
stationary and the right part being pushed down by the and in other words there is in any 3 weights l} 2 or loaded beam tangential shearing stress along any trans-
W W
verse section.
The magnitude
is
equal to the load on one side of the section divided by the area of the section. In the beam of Fig. 25, the only load on
Fig. 25.
the
left of
the section
HH
is
load TF X
is
p A
Had we
and
section
on the left of the 2 we would have had two loads and acting in opposite directions, so that the shear-
P
ing stress would have been
A.
will assume is passed. as positive the conditions as in Fig. 25, the tendency being for the part of the beam to the right of the section to move down; then let us construct a curve of shearing force using
We
beam loaded
as shown.
found above. For example, Fig. 26 Taking the left end as origin,
the total shearing force at that end is equal to the support= P = 29 Ibs., which it remains ing force there, or S. F.
In Chapter II we took our shearing forces indefinitely near together Shear and bending to get pure shear, that is, shear without bending. are closely connected, so that it is difficult to produce the one without the other.
*
55
the section to the right, we get to the first in the opposite direction to the supIbs., porting force; so, consequently, as we pass this load the total shearing stress drops to 19 Ibs., where it remains until we
we move
load, 10
which acts
10 Ibs
20 Ibs
30 Ibs
Q=31I
29
?
-X
-31
I
Fig. 26.
come
Here
it
drops to
1 Ib.
At
this-
point the tendency for the right part of the beam to move down ceases, as the sum of the loads on the left side of a
section from this point on will be greater than the supporting force at the left end. Passing the 30-lb. load, the shearing
stress again drops, this
time to
31
Ibs.,
of
shearing force will be the series of steps These values, with their signs, are for the left side of the
ABCDEFGH.
on the right side the stresses are equal to those found but opposite in direction. Had we used the right end for origin and the left side down as the positive direction, our curve would have been a series of steps down to the left, with numerical values the same as before.
section;
34.
If
we take
all
the weight of the beam or, what is the same beam in the preceding article to be uni-
formly loaded
along
its
56
STRENGTH OF MATERIAL.
we move our
section to the
Let Fig. 27 represent a beam so loaded; then if the right. ordinate of the line AB represents the load on unit length of
beam,
Fig. 27.
\%
57
and the supporting force, the S. F. being equal to P wx, where w is the load per unit length, and x the distance from the left end. The shearing curve will therefore drop steadily, The S. F. curve is CD. If we have in as in the figure. addition to the uniform load several concentrated loads, the curve of shear will be as in Fig. 28, with a drop at each concentrated load. If drawn to scale, these curves will give the shearing force at any point of a beam by measuring the ordinate at that point. As a GENERAL RULE, then, the shearing force at any transverse section of a loaded beam is equal to
the algebraic
section.
35.
sum
Hereafter
we
for the
With conorigin in the equations for curves of any kind. tinuous loads, L, the load at any point will vary in some
way with the distance from the origin; for example, a beam "a" ft. long carries a load which uniformly increases from
zero at the origin to w Ibs. per ft.-run at the right end. Here the load per ft.-run at a distance x from the origin would be
>
=
a
,
of the
L=
wx
For a
a
L w. The equations for load curves are easily found and are very useful, for let us notice the relation between the loads and the shearing As a general formula for concentrated force at any section. loads, we found the S. F. at any section to be equal to P %W. With a beam loaded with any continuous load, if L be the load per unit length, then Ldx is the load on any elementary length, dx, of the beam, and the total load from the origin to a section at any distance, x, from the origin is
uniform load of
Ibs.
per ft.-run,
(*x
I
load curve.
Now
the algebraic
58
STRENGTH OF MATERIAL.
of all the loads to the left of the section, and that is also our definition of shearing force. As a general rule, then, for any continuous load the shearing force is
sum
S. F.
= C *Ldx.
integration
In using the formula we must remember that the constant of is the value at the origin of the quantity, repreis,
we must still use S. F. and if a continuously loaded beam supports also concentrated loads we must find the shearing
rately,
=P
a
2 W, number of
forces sepa-
algebraically adding the results (principle of superposition). In this latter case also the supporting forces for both the continuous and con-
by
Examples:
15 ft. long is supported at the ends and carries from the left end, 1 ton 8 ft. from the left end, 4 tons 5 ft. ft. from the left end. Find the supporting ton 10 and J forces and draw the shearing curve.
1.
A beam
Ans.
2.
P =
3.3 tons.
ft.
Q =
2.2 tons.
with 500
the
left
spar 20 Ibs., 4
long is supported at the ends and loaded ft.; 250 Ibs., 9 ft.; and 900 Ibs., 18 ft. from
end.
ing curve.
Ans.
P =
Q -
1022.5 Ibs.
3. A plank 16 ft. long is laid across a ditch and a man weighing 192 Ibs. walks across it. Find the shearing curve when he is 3 and when he is 8 ft. from the left end.
59
4. A weight of 384 Ibs. is placed 5 ft. from the left end of What is the shearing force at a point 6 ft. the above plank. from the left end when the man is 8 ft. from there?
Ans.
5.
- 24 Ibs.
ft. long has a uniform load of 50 Ibs. per curve of shearing force and give value at and 13 ft. from the left end.
A beam
ft.
18
ft.-run.
Draw
At 7
the
points 7
Ans.
6.
ft.
100
of
Ibs.;
at 13
ft.
200
Ibs.
On
beam
example
5,
weights of 300
Ibs.
and 500
are placed 6 ft. and 12 ft. respectively from the left end, Draw S. F. curve and give in addition to its uniform load. value of S. F. 8 ft. from left end.
Ibs.
Ans.
7.
116
Ibs.
A beam
ft.
long has
its left
end fixed
end.
in a wall
and
the
its free
What
is
The beam
per ft.-run.
of
Ibs.
What
example 7 has a distributed load of 100 is the maximum S. F.? and draw the
curve.
15 ft. long and 1 ft. square floats in sea loaded at the center with a weight which will Draw curve of S. F., and give maxijust immerse it wholly. mum value. (35 cu. ft. of sea water weighs 1 ton; 1 cu. ft. of oak weighs 48 Ibs.)
9.
An oak beam
It
is
water.
Ans.
Maximum
S. F.
120, Ibs.
10. A pine beam 20 ft. long and 1 ft. square floats in sea water, and is loaded at the middle with a weight which will Draw a curve of S. F. and give value 5 ft. just immerse it. from left end. (Cu. ft. pine weighs 39 Ibs.)
Ans.
S. F. 5 ft.
from
left
end
125
Ibs.
60
STRENGTH OF MATERIAL.
11. A beam 20 ft. long, supported at the ends, carries a at the left end to 50 load which uniformly increases from Draw the curve of S. F., and Ibs. per ft.-run at the right.
find its
maximum
value
is
beam
where
where
Ans.
its
zero.
Maximum
ft.
value
333J
Ibs.
Value
zero
11.5+
12.
at the ends
The buoyancy of an object floating in the water is and increases uniformly to the center, while its
at the center and increases uniformly to the end. weight is Draw curve of S. F., and give maximum value.
Ans.
Maximum
S. F.
=
4
CHAPTER
VII.
In Chapter II
it
beam
is
and
verse section, these stresses being compressive on one side Art. 14 tensile on the other side of the neutral plane.
of the
tral axis of
same chapter shows that the moment about the neuthe external forces on one side of any section
must be equal to the moment about the neutral axis of the on the same side of the section. Definition: The bending moment at any section is the moment about the
stresses
all
of a
at the section
HH
M
W^
= Px -
(x
x,)
(x
x 2 ),
or finding the line of action of the resultant of all the forces etc., and calling its distance from the section d 2
M =Px
which
is
- 2
61
62
STRENGTH OF MATERIAL.
If we now consider the increment AM which the bending moment receives if we take our section a distance Ax to the right, the bending moment about the neutral axis of the new section will be
M
but Px
AM = P (x
=
is
Ax)
2Wd
the original bending moment equal to M, for the shearing force (F)
AM = M +
limit
FAx, or
AM =
FAx,
dM = F dx;
integrating,
we have
bending moment
M =/F dx.
This equation is true for any kind of load, but care must be taken to use the correct constant of integration, which is This for beams free at the at the origin. the value of
origin in any
We
but if a beam is fixed (prevented from moving the origin, there is a bending moment there. at way) will devote the rest of this chapter to some examples of
is
zero,
moments
in
supported at the. ends is loaded as shown in the curves of shearing force and bending Find Fig. moment. By definition the S. F. = P SPF, by which we F. to ABCDEF be of S. Considthe curve (Fig. 30, a). get
30.
A beam
ering each load separately, the supporting forces for the 25-lb. load are P = 17.5, Q = 7.5, and the S. F. curve is
A BCD
The
p =
If
Q =
28,
and the
curve
is
ABCD
algebraically the ordinates given by these curves at any point distant x from the origin we will get the ordinates for the S. F. curve for that point given in Fig. 30, a.
we add
251bs
351bs
(63)
64
STRENGTH OF MATERIAL.
for the
Obtaining the ordinates by definition, the curve of B. M. beam with these loads is given by OGHX in Fig. 30, a.
Let us get separately the curves of B. M. due to each load. For the 25-lb. load we get by definition the curve in Fig. 30, d, the maximum B. M. being directly under the load and the curve being positive at all points. For the 35-lb. load
we
at
'30, e, this
any point distant x from the origin we will the ordinate of the curve of B. M. for that point as given get in Fig. 30, a. Now by definition, the bending moment at the middle of the beam, for example, is
24.5
If
we add together
25
72.5
Ib.-ft.
it is - .5 X 5 = 2.5, which but is due to the fact that evidently incorrect, having taken the two concentrated loads together, the shearing
fF dx
force of one being positive and the other negative, we have not multiplied the total shearing force by x. The moments of the two shearing forces cause bending in the same direction,
therefore,
if
we
we
have assumed to indicate direction only) the shearing force at this point will be 7 + 7.5 = 14.5, which multiplied by 5
With many loads to get the shearing gives 72.5 as before. force separately would be a tedious operation, so it is better to make it a rule to get the S. F. and B. M. for concentrated
loads from the definition.
We
will
find
no trouble with
beams having continuous loads unless there are concentrated loads in addition, in which case we get the curves due to the continuous loads by formula, and those due to the concentrated loads by definition, and apply the principle of superposition.
38. A beam 10 ft. long supported at the ends is loaded with a uniform load of 25 Ibs. per ft.-run. Find the curves
65
for-
and B. M.
mula
is
very convenient.
L C
w = -
25
Ibs.
25 x
is
+
x.
C.
the origin
equal to
P =
125
Ibs.
F =
125
25
(1)
Fig. 31.
This being an the equation to the curve of S. F. line and is a the first to straight plots as the degree equation
(1) is
line
AB
of Fig. 31.
is
M
or,
= /Fdx =/(125 25 x 2
-=
25 x) dx,
M
C
125 x
zero because B.
[(7=0,
M.
is
(2)
is
(2) is the equation of the curve of B. M., and being of the second degree is a conic (parabola) and plots as OCX of The maximum B. M. is at the middle of the beam Fig. 31.
where the
S. F. is zero.
To
66
STRENGTH OF MATERIAL.
(1)
or (2)
A beam
ft.
right end unsupported, carries a weight of 50 Ibs. on the Find the curves of S. F. and B. M. right end. In this case the left end supports the whole load, so P = 50, and the shearing force by definition (concentrated
loading)
is
F =
50
Ibs.,
the
moment by
definition
is
line,
Q2
varying from zero to 250 Ib.-ft. This would give us a line inclined
upward from
know the
greatest B. M.
is
at the origin.
Now
beam is just the opposite of that of a beam supported at the ends, the center of curvature being below the beam in this case, while it is above a loaded beam supported at the ends. In fact if we turn Fig. 32 "upside down" we will have just one-half of the beam supported at
the curvature of this
P in the middle, being one of the supporting forces; so this kind of bending is called negative, and instead of the curve of B. M. inclining upward
the ends and loaded with 2
from 0,
it
inclines
downward from
as in the figure.
The
and move the curve plots directly if we take the origin at section to the left, for this arrangement is the same as a
beam
40.
with 50
twice as long supported in the middle and loaded Ibs. at both ends.
A beam
ft.
left
end unsupported, carries a uniform load Find the curves of S. F. and B. M, ft.-run.
right
67
C.
the origin
is
equal to P,
=125
Ibs.
(1)
.-.
F =
125
25
x.
Fig. 33.
(1)
first
degree
is
a straight line
is
and plots
AX
in Fig. 33.
125 x -
25
x-
Cr
Here C
is
not zero.
z=5,
=
from which
get
125
+ Cv C we
l
C =
l
M
is
= l25x
^jti x *U 25
312.5
(2)
second degree
Fig. 33.
a conic
This equation gives a maximum negative value of B. at the origin, where we know it should be.
M.
68
41.
STRENGTH OF MATERIAL.
A beam
Ibs.
10
ft.
is
loaded
ft.
per ft. -run and a concentrated from the left end. Find the curves of
and B. M.
Fig. 34.
For the uniform load (Art. 38) the curve of For B. M. the curve is 01 X. For the concentrated load the S. F. curve is the curve of B. M. is OJX.
(Fig. 34).
S. F.
S. F. is
AB
CDEF, and
Adding algebraically the respective ordinates, we get the curve for both loads to be GHMN, and for B. M. the
is
OLX.
is
A beam
10
ft.
long
load uniformly increasing from zero at the left end to 100 Find curves of S. F. and Ibs. per ft.-run at the right end. B. M.
Here
L = S. F.
100 x
10
10 x,
10
=/Ldx =/-lOxdx =
C,
69
can find
being the S. F. at the origin is equal to P. We by the method used in the example at the end of
OL
is
The
Fig. 35.
beam from
0,
and the
total load
is
100
Xfit
= 500 Ibs.;
therefore, taking
moments about
0,
500
10
- Q X
10
0;
and Q
or
= 333J, P = 166.
333 J;
P in another = P - 5x
2 2
way,
for
and
B.M.= J(Fdx=
C
l
( J (P
- 5x )dx=Px
5x 5
equal to zero, for the bending moment at the origin is is also zero at the right end of the beam, so that zero, and if we substitute x = 10 and solve the equation
is
PX
10
X - = -5
-
1000
70
STRENGTH OF MATERIAL.
get
we
P =
166
as before.
in the
equation for S. F.
and B. M. we get
S. F.
166
5 x2
(1)
and
B. M.
166
(2)
which equations give the curves ACB for shearing (Fig. 35) and ODX for bending. If we put (1) equal to zero and solve for x we get the point on the beam where the shearing force is zero; and if we put
this value of
x in
the
maximum
(2) we will get the maximum B. M., for B. M. occurs where the S. F. is zero (see Art.
28), for by the principles of maxima and minima, the first derivatives of the B. M. with respect to x, put equal to zero, will give us the shearing equation (1) equal to zero,
d (BM) ' _b dx
166
- 5z =0;
2
500
5
from which
is
x=\/V 3 x
10
,
V3
maximum.
Examples
1.
A beam
10
ft.
of 1000 Ibs. 4
ft.
long, supported at the ends, carries a load from the left end. Find curves of S. F.
and B. M.
2.
A beam
ft.
long, fixed at the left end and unsupported Ibs. at the right end. Find
A beam
10
ft.
Ibs.
long, supported at the ends, carries a uniper ft.-run. Find curves of S. F. and
B. M.; give values at ends and center. Ans. S. F., ends B. M., ends 0; center 500; center 0.
1250
Ib.-ft.
71
4. A beam 5 ft. long, fixed at the left end, unsupported at the right end, carries a uniform load of 100 Ibs. per ft.-run. Find curves of S. F. and B. M. and give values at ends. B. M., left end Ans. S. F., left end 500 Ibs.; right end 0.
- 1250
5.
lb.-ft.;
right
end
0.
10 ft. long, supported at the ends, carries 400 from the left end, and 600 Ibs. 6 ft. from the left Find curves of S. F. and B. M. and give values at the end. ends and center. Ans. S. F., left end 480 Ibs.; right end 520; center 80. B. M., left end Ibs.; right end 0; center 2000 lb.-ft.
Ibs.
A beam
ft.
6. What is the longest steel bar of cross-section of 1 sq. in. that can be supported at its center without being permanently bent, the greatest allowable bending moment for
20 ft. long, supported at the ends, carries 2000 from the left end, and 5000 Ibs. 4 ft. from the right end. Find curves of S. F. and B. M. and give values at the ends and at the loads. Ans. S. F., left end 2500 Ibs.; right end 4500 Ibs.; between loads 500 Ibs. B. M., end 0; first load 12,500 lb.-ft.;
7.
A beam
Ibs. 5 ft.
lb.-ft.
If
the
beam
of
example 7 were loaded with 200 Ibs. per and B. M. and give values at
2000
Ibs.;
center
0.
B. M., ends 0;
round
steel
rod of 2
ins.
a bending moment of 6 ton-ins. What is the greatest length of such a rod which will just carry its own weight when sup-
72
STRENGTH OF MATERIAL.
10. A beam 20 ft. long, supported at the ends, carries a uniformly distributed load of 5 tons, and a concentrated load of 5 tons, 4 ft. from the left end. Find curves of S. F. and
B. M. and give values at the center. bending moment? and give its value.
Where
is
the greatest
Ans.
B. M.,
11.
S. F.,
center
ton.
B. M.,
ft.
maximum
24^
ton-ft.,
from
left
water.
It is
pine beam 20 ft. long and 1 ft. square floats in sea loaded at the center with a weight just sufficient
to immerse
Find curves of
S. F.
and B. M. and
cu.
ft.
Ans.
Ib.-ft.
Maximum
S. F.,
250
Ibs.
Maximum
B. M., 1250
12. A beam 54 ft. long, supported at the ends, is loaded with 15 cwt. per ft.-run, for a distance of 36 ft. from the left Find the curves of S. F. and B. M. What is the maxiend.
mum
end?
B.
B. M. and the B. M. at
6, 12,
and 36
ft.
from the
left
Ans.
ft.;
B. M.
maximum =
216
ton-ft.; B.
M. 6
94.5 ton-
M. 12
162 ton-ft.; B. M. 36
162 ton-ft.
beam 5 ft. long is fixed at one end, unsupother the end, and is of rectangular section 2 ins. ported at wide and 3 ins. deep. What weight at the free end will de13.
steel
is
24 tons per
sq. in.?
14. The buoyancy of a floating object is at the ends, and at increases uniformly to the center, while the weight is Find the the center and increases uniformly to the ends.
curves of
S. F.
of the displacement,
Ans.
S.
and B. M. and give maximum values in terms Z>, and the length, /, of the object. ID D B. M. maximum = F. maximum =
;
CHAPTER
VIII.
the
beam
is
bent.
The
deflection at
any section
of a loaded
beam
is
the disline
to the point
pierces that section; or, it is the ordinate at that section of the neutral line (see Fig. 36).
from which
El R =
>
being a constant and / also, in this case, as we are considering beams of uniform cross-section; M, of course, varies at different sections of the beam.
By
any
by
its
rectangular equation
is
dx 2
R we
have
TM M
d?y
dx*
73
74
STRENGTH OF MATERIAL.
which by integration will give us the equation to the curve As this integration would be into which the beam is bent.
dimensions of the different pieces of material are such that the bending is very slight, we can without appreciable error
simplify the operation considerably as follows:
dy being the ax
tangent of the angle that the bent beam at any point makes with the axis of X, is a very small fraction, and being squared in equation (1) becomes so small that it may be neg-
El
I
----
.
;
M
and integrating
d2y
or,
El
d*y
dx z
= M;
dx 2
this equation
we
get
(2)
EI=/Mdx, dx
which
will give
we
substitute for
us the tangent of the slope at any point when its value in terms of x as found in Chap-
Mdx is called the The integral it we will and by S. When S is designate slope function, divided by El we have the tangent of the angle of slope.
ter VII,
and
integrate.
If
we
Ely =/Sdx.
This
is
(3)
beam is bent, of y given by this equation is the ordinate of the neutral line at any section distant x from the origin.
the equation of the curve into which the
usually negative.
75
(2)
we must not
a
and
(3)
If a beam is fixed at the origin, the slope beam supported at the ends and loaded
curve like that of Fig. 36. Clearly the slope is greatest at the ends and there will be a constant of integration for equation (2). We will usually know from the way in which the
beam
is
is
zero.
76
45.
STRENGTH OF MATERIAL.
A beam
10
ft.
long, supported at the ends, is loaded Ibs. per ft. -run. Find the slope
is perfectly symmetrical. Let Fig. 36 the the bent and OX the beam, being origin represent of the line the was neutral load before applied, the position dotted line representing its position after the application of
the load.
M
dx
oe
-25.T
125.
0,
[C
P],
~2
125
x+
[C
2
is
Knowing
the bending
symmetrical,
-1 dx
-
0,
where x
(the middle), so
In case we do not know the bending is symmetrical, we carry C l down through the next integration for deflection,
which gives
Elv
= ~
^f + nr + CtX + [C
is
'
(2)
is
tion
also
zero where x
we
get
X ---25
=
l
r~ +
10000
-
-X as
before,
1000
+ioc,,
and equation
(1)
1041
*?!
!?. -10411
(3)
77
the
from which by substituting the abscissa of any section of beam for x and dividing the result by El we get the
Substitut-
in
equation
(2) gives
(4)
from which the ordinate of the neutral line (curve of bendIn finding the value of ing) at any section may be found. this ordinate, or of the slope, care must be taken to use the same linits throughout; for example, if we have a steel beam and E is given as 30,000,000, it is in pounds per square inch; we must therefore use x in inches, find / for the section in inch units, and reduce the bending moment
to inch-pounds;
It is
convenient to solve this problem by using letters to represent the numerical data and to make the substitutions
later in the equation
example,
equal
in the
"w"
which gives the desired result; for above problem let the load per foot-run and the length of the beam "a," then
w,
,
L =
M
dy
= - wx
wx 3
=0,
/a\ 3
(
\2J
wx
wa
wa
wax
wax
78
STRENGTH OF MATERIAL.
By this latter method, the particular result desired may be obtained without doing the numerical work required for the other equations. In the above beam the maximum
slope
is
at the ends,
of the angle
is
-7/Y7
The maximum
and there
46.
=
j,
beam,
5 iva 4
A beam,
centrated load
supported at the ends, carries a single con-.. at a distance a from the left end and b
Find equation
for slope
and
deflection.
a+b
Fig. 37.
a+b
In this problem the beam will be bent as shown in Fig. 37, and the elastic curve will consist of two branches, the part from to the weight and that from the weight to the other end of the beam. The shearing force on each part will be constant, but the values will be different and they will have different signs. WT e must consider the two parts sepaWith the origin at 0, the bending moment for any rately.
section
= -Wbx -,
a
dy _ 2 dx
+ b Wbx (a + +
6)
Ely
Wbx s
6 (a [C2
6)
0.
79
For the part to the right of the load we will take our origin at the right end, then, letting ;r, be the distance from
the right end to any section H'H' be
',
the bending
moment
will
M-
X Qx
the sign being negative because the moment tends to turn the right end of the beam counter clockwise, or in the opposite direction to that of the other end; we have then for the
right
end
*
d,i
*&, + b
Wax*
2 (a
dx
b)
If
we move
left
we
M
dy dx
= Wa
(a
+ +
6
b
x)
Wa
2 (a
b}
Now for the section under the slope and deflection are the same, using either the equations for the part of the curve to
the
left of
W,
W,
so
we
80
STRENGTH OF MATERIAL.
Wba2 (a
Wab 2
6)
2 (a
6)
(1)
Wba 3
6 (a
6)
6 (a
or,
6)
C> +
C/6
=
(1)
(6
a)
(2)
From
and
(2)
we
get
6)
Wab
1-
(a
2 6)
8
6)
'
_ "
Tf afc (2 a
6 (a
+
6)
6 (a
/
of C,
and
(?/
we g e *
3
Wbx*
2 (a
6)
Wab (a + 2 6) 6 (a + 6)
<% == dx
_TFa(a+6-a;)
2 (a
6)
6 (a
6)
EIy = 6
Wa (a +
(a
6)
6 (a
Ely
6)
- xY
6)
6 (a
TFa6(2a
b)(a
x]
6 (a
6)
we
be
El
(a
6)
is
deflection will occur in the longer segment, and at the section of maximum deflection the slope will be zero; there-
mum
81
fore, supposing a to be greater than b if we put the equation of the slope for the part of the curve to the left of equal to zero and solve for x we will get the abscissa of
the section of
maximum deflection; and substituting this value of x in the equation for the deflection will give us the maximum
deflection, as follows:
Wbx 2
and
this value of
Wab
(a
2 b)
(a
2 6)
x substituted in
Ely
shows the
--Wbx 3 Wab
(a
6 (a
b)
6 (a
+ +
2 6) x
b)
maximum
ymax
deflection to be
~ ~
3
Wb
El
(a
/a (a
+
3
2 b)\
'
6) (
or,
if
6,
Wa
Umax
6 El
Examples:
1.
A
if
steel
beam, 10
ft.
load
/ in inch-units
is
84.9 and
E=
30,000,000?
Find
maximum
Ans.
deflection?
E =
30,000,000.
Find equation of
elastic curve.
1.3
ins.
82
3.
STRENGTH OF MATERIAL.
carries a
uniform load
It
is
10
ins.
wide.
.39
A
left
beam, 12
end.
and
long, 8 in. deep, and 12 in. wide, is supcarries a load of 1200 Ibs., 3 ft. from
E =
ins.
1,200,000.
Find the
elastic
curve and
the
maximum
.102
steel
deflection.
Ans.
5.
beam, 60
ft.
Ibs.
per
ft.,
If
maximum
deflection.
E=
ins.
ft.
Beams, 20
ft.
The beams are spaced 4 ft. apart. of the beam to be square, find the
Supposing
side of the
in.
may
not exceed \
12.18 ins.
CHAPTER
IX.
Continued.
47, Example: A beam of length a is fixed at the left end and unsupported at the right. It is loaded with a uniform load of w Ibs. per ft.-run. Find the equation of the
elastic curve.
L = F =
w,
wx + C
wx + wa (P
l
=
is
whole load),
found
in Art. 40),
M=
dii
+ wax + [C =
wx 3
(C l
El
dx=--&
wx
4
wax 2
wa'2 x
^r
3
-2wa x
2 2
+ [c> =
(beam fixed at
origin),
E/J/=
~2? +
wax
-6"
^+^=0
wa 4
=
(beam fixed at
where x
origin).
a.
The maximum
I/max
8 El
up
free end of the above beam is propped same level as the fixed end. The prop now supports some of the load, so we do not know P.
L = w, F = - wx + C = - wx +
P,
= -
+ ^f a
Px + C
83
84
STRENGTH OF MATERIAL.
the bending
We know
prop
is
moment
zero, so putting
M=
from which
>--- Pa.
Substituting this value of
C we
l
get
85
zero at x
=
,
and
substi-
M. equal to
The maximum
will break,
B. M.
if
is
there-
128
overloaded,
is
also at a point between there and the fixed end. Putting the equation for B. M. equal to zero and solving for x gives
and
a and x
a 4
=a
4
is
called a virtual
joint, because, if
had a hinge
cause
it
to turn.
and solving
for x gives
a and a value greater than the length -of the beam. .58 a the slope is zero, and this is the point of maximum deflection. Substituting this value of x in the
x
.58
Where x =
wa 4
Compare the curve of B. M. for this beam with that in Fig. 33. As soon as the prop under the free end of this beam
begins to bear a part of the load there exists a positive B. M., and the virtual joint, which is then near the right end of the
beam, moves toward the fixed end, as the right end is propped up and the load on the prop increases; but the results due to change in conditions are readily followed. 48. A beam a ft. long is fixed at both ends and carries
a concentrated load
at its middle.
Here
P= Q=
86
STRENGTH OF MATERIAL.
S. F.
.*.
W and
is
has opposite directions on opposite sides of the load; therefore, as in Art. 44,
beam
separately.
we must consider the two parts To the left of the load, then,
(C
is
of the
M
dx
4
not known),
substituting x
a
i
The equation
then
'
of the curve of
bending to the
left of
the load,
is
Wx
Wa
/\
87
Now
straight lines in
it is clear we cannot embrace both of these one equation of the first degree, and for this
we must consider the two parts separately. Before proceeding, we will notice that the bending moment has the
same value with
different signs at the ends and in the middle. beam is as likely to break at the ends as
middle
if
Wx
Wa
The maximum
deflection
is
at the middle
and equal to
'
/max
~ Wa
IQ2YI'
In the cantilever bridge the
49.
joints are placed at the points where the bending moment would be zero if the bridge were continuous over the whole
two
will consider a beam fixed at both ends, having span. fixed joints and carrying a uniform load of w Ibs. per ft.-run. There being joints at F and G (Fig. 40) we must consider the part FG as a separate beam supported at the
We
ends, the load on it being equally divided and supported at F and G by the beams and GX. From the conditions
OF
we could assume
and Q with
this loading to
be equal to
(a
+- +
6
c)
j
L=
F = - wx + C = - wx +
w,
P,
88
STRENGTH OF MATERIAL.
at the joint
is
zero, so
0=
w
and from equations
(a
6)
+C
(2)
19
(2)
(1)
and
we
1
get
= -(2a + 6),andC -- -^
substituting,
= - wx + w -(2 a +
,4
6),
The
joints being
where B. M.
is
and
but for slope and deflection we must consider each part as a separate beam,
B. M. will be continuous as
shown
Fig. 40.
the parts at ends having in addition to their uniform load a concentrated load at their ends, F and G, equal to half the total load on the middle part. For equal strength, the bend-
89
wa
(0
6)
= wb
whence
= ?r;
or,
4 a
=2
2
;
or,
(2
must equal 2
of the
2
,
and the
=.
-
joint
beam
span
2V2
50.
Traveling Loads.
If
a load
moves from
left to
right across a
beam
(-*>
Fig. 41.
for
P is obis equal to P (Fig. 41). any position of moves across is just over it, and as viously greatest when is just the beam P's value drops uniformly until when over Q, P's value is zero. We can then represent the change
W W
of the positive S. F. by the line AX, and by the same reasoning the change in the negative S. F. would be represented
by OB.
tion of
W the B.
Considering the B. M.
we know that
for
any
M.
is
M=
Px
W and
posi-
(a
x) x.
By
the principles
of
which
90
STRENGTH OF MATERIAL.
putting the
first
is
maximum by
derivative of
M with
dM =
dx
W
a
(a
2 z)
= 0,
which gives
the value of
B. M.
If
x,
or the position of
is
maximum
long enough, it extends completely over the not long enough for this the maximum positive bridge; S. F. occurs when the whole train has just got on to the bridge
the train
is
if it is
of the train
is
just
when
Oblique Loading. Loading is said to be oblique a principal axis of any cross-section of a beam does not lie in the plane of the external
beam and let the arrow-head, marked M, represent the direction of the B. M. The axis of X is perpena
dicular
to
the
plane
of
the
paper
of
and
42
are shown.
Resolve
M into
is
The
ents parallel to the axes of direction of the fiber stress due to bending
to the
Y
it,
componand Z.
perpen-
dicular
of
due to
sin a,
AD
of the section is
p.--
M sin a --
->
91
obtained by substituting
in
sin a, the
component
moment,
being the
-=
,
moment of inertia of the section about the axis of z the distance of the line AD from the axis of Y. and Y, The normal fiber stress perpendicular to the plane of the paper on AB is cog a
at
fiber stress
p
52.
= PV+ PZ= M
sin
M cos a
-j-
to
The work done in bending a beam is evidently equal is a uniform bending moment and 6 is the M6, where If I is the length of the beam and angle of slope at the ends.
it is
bent, then 6
=
2
and from
ME =
I
we have R
M
is
El -
MH
equal to
2 El
But bend-
moments moment
Work=
/Af'fa.
Examples:
supported by a row of uprights fixed at their base and their upper ends held vertical by struts sloping at 45. Water pressure varies as the depth, or L = wx.
1.
A dam
is
What
Length
of
upright a.
Thrust
92
2.
STRENGTH OF MATERIAL.
railroad
is
inclined at
The
apart and the rails are 1 ft. inside the The ties are 8 in. deep and 6 in. wide. The load stringers. transmitted by each rail to one tie is 10 tons. What is the maximum normal stress in each tie?
stringers are 10.5
ft.
Ans.
3.
6428.8
Ib.-ins.
2.
beam,
ft.
is
uniformly
deflec-
loaded with
tion
Ibs.
per
Find the
1/Jfl
maximum
Virtual
and the
virtual joints.
^
Ans.
Maximum
deflection =
/J).
where x
(1
24 El
joints
4. A beam, a ft. long and fixed at the ends, carries a uniformly increasing load from zero at the left end to w Ibs. Find the maximum deflection and per ft.-run at the right.
Ans.
Maximum
deflection
.
-if 1/7
where x
a
-
2 a
3125 El
Virtual joints
and
5. A beam, a ft. long, fixed at one end and the other end propped up to the same level, carries a uniformly decreasing load from w Ibs. per ft.-run at the fixed end to Find the equation for deflection, zero at the propped end. the position of the maximum positive B. M., and the position
Ans.
Maximum
beam, a
ft.
positive
B. M.
where x
a \/$.
Vir-
a >/|.
long, fixed at both ends, carries a single
concentrated load
end.
Find
Ans.
Wd
(a
d)
3 Ela*
93
If
beam
in
maximum
Ans.
= Wa
192 El
8. A single load of 50 tons crosses a bridge of 100-ft. Draw the curves of maximum S. F. and B. M., and span. give the values of those quantities at half and quarter span.
9. A train, weighing 1 ton per ft. -run and 112 ft. long, Draw curves of maximum crosses a bridge of 100-ft. span. S. F. and B. M., and give values at half and quarter span.
a load equal to k times its own uniformly distributed, second concentrated at its middle; considering it as a beam fixed at the ends, find the distance apart of the bearings that the ratio of deflec10.
weight,
first
tion to span
may
be
3
Ans.
(1)
Span
in
feet= 10.5
/~J2 \/ K +
3
y
*
/C
~T~
(2)
Span
8.3
(d in inches).
T?
CHAPTER
X.
CONTINUOUS BEAMS.
beam is one which extends over several In this supports. chapter we will consider as heretofore such beams as have a uniform cross-section and, as in only all practical constructions the supports are adjusted so as to allow as little strain as possible in the material, we will
53.
continuous
assume all the supports to be at the same level. It is obvious that the bending moments at the intermediate supports will be negative, as at these points the conditions are similar
to those of a
a single support.
If
the
end spans are short we may have the supporting forces at the ends equal to zero, and if the ends are " anchored " (fastened down to the support) we may have a negative supporting force, that is, one acting in the same direction as the
Fig. 43.
loads.
we see approximately the curves of moments and shearing force for a continuous beam bending
In Fig. 43
carrying a uniform load and having five equally spaced supThere are two virtual joints between supports exports.
we
will find
CONTINUOUS BEAMS.
95
uniformly loaded beam of span length supported at the ends and one uniformly loaded of span length fixed at the ends. The difficulty in working with continuous beams lies in finding the supporting forces, for the usual method of taking moments will not do, there being two unknown quantities in each equation, and the equations reducing to identities
For beams having only the solutions are not difficult, as will supporting forces, be shown; but as the number of supports increases the cal-
when we attempt
three
to solve them.
culations
54.
tedious.
is
A beam
equidistant supports. supported by length 2a carrying a uniform load of w per unit length and supported at the ends, has a maximum deflection equal to
three
A beam
of
---
(see
Art. 45).
like
beam supported
at
the
maximum
deflection equal to
R
3
(2a)
48 El
Now
beam may be
considered as a uni-
formly loaded beam which has a prop at its middle by which the middle point is propped up to the same level as the end
supports. Obviously then the deflection at any point will be that due to the uniform load minus that due to the
upward we have
~~
~48W
384 El
The supporting
w P = Q =-
- 1 wa
ft
wa.
96
STRENGTH OF MATERIAL.
forces
we have now no
difficulty in
getting the equations for slope and deflection, for, taking the origin at the middle, the B. M. for any section distant x from
L_I
Fig. 44.
the origin
is,
by
definition
R
J,
which
is
R\
El
dy dx
T
Rx =-
46
~~ ~
WX 3
-
+ MQ X + +
[C
f
.
.
from symmetry
the slope is zero at the origin.
deflection
is
<
r
77,
"&
WX
J=
X
[
l=
have
^ the
for the B.
zero
R we
-
M. at any
M = f wax
And
x
as the B. M.
is
Q.
we have,
;
substituting
a,
the value of
M
ft
equal to
wa
o
or
M=
wax -
wx 2
wa 2
;
CONTINUOUS BEAMS.
97
equal to zero and solving for x putting this value of a = as the position of the virtual joints. Ingives us x
tegrating
we
and
-
deflection,
El
and
dy fdx
wax 2 -
wx 3
16 5
68
wa 2 x
+ [C - 0,
~
^
wx 4
"
wa 2 x 2
16
l
48
"24""
To show how
carefully the level of the supports must be adjusted, suppose there is left a deflection over the middle of the total deflection which support, equal, let us say, to
5w
R=
w
(2' a)
_5w
(2 a)
(2 a)
'
384 El
(2 a)
384 El
48 El
If this
from which
deflection were in the other direction, or we would have 4 the total load. Remembering that the deflection in
,
R =
any case is very small when we see that a variation. of it up or down causes R to change from j to J the total load, we can understand how carefully the supports must be adjusted to the same level. 55. With concentrated loads we must proceed in a different way. Suppose a beam which is supported at the middle and ends carries a concentrated load midway between the
supports, as represented in Fig. 45. Taking the origin at the middle as before and considering the right half of the between the beam, the bending moment at any section
.
HH
origin
is
(Art. 46)
(a
x).
(I)
98
Integrating,
STRENGTH OF MATERIAL.
dy
Wax
and
Integrating,
-
^T +
(C
?.
(5a)
^3 -i
Q=Xw
Fig. 45.
The
is
in equations
(2)
and
Wa~
Wa
Qa
Qa 2 = _Qa
~g~
Qa
~^~
Substituting,
~2~~
~2~
~8~
Wa
=
~8~'
dy
Qx
Wa
CONTINUOUS BEAMS.
Integrating,
99
E-M
The
deflection
Cl
=,
(6a)
is
and
3
(6a)
we have
3
Wa^
'~16
or,
TFo 3
48"
Qa
8
3
'
Qa
48
= Qa " Qa
"
"
Wa
16
48
Q lf
Wa
Ll=
Substituting,
3
'
48
Qax
Qx
Wa
Wa
is
Now
a, solv-
Q =
TF
W.
From symmetry, P
equals Q,
and
R must
R=2W-(P +
The methods
most
tice,
Q)
= V W.
of this
of the cases of
and the preceding article will cover continuous beams found in actual praccases where
for
beams have more than method known as the " Method of Three Moments must be employed. This method came into use about 1857, and is a general method
but there are
supports,
many
three
and
these "
Let Fig. 46 represent the part of a beam over any three consecutive supports, and let the loading be uniform between adjacent supTake the origin at P and let the bending moments ports.
100
STRENGTH OF MATERIAL.
at P, R and Q be ly 2 and 3 respectively, the distance between supports to be a and a lt the loading between P and R be w Ibs. per unit length, and between R and Q be w Ibs.
l
M M
J
L
|p
T
^
----
4
[R
|Q
Fig. 46.
HH between P and R
moment
at
any section
(Art. 45)
M
But C
in this case
is
wx z
=
+ Px +
lf
C.
equal to
so
Integrating,
El
dx
= M.x + P
26
[C
?,
(2)
and
+ tc.-o B/y-ar^+P^-^+Cx 6 24
(level supports).
(3)
Now
2/
=
2
when x
=
im
a,
4
hence
= ATa
2
Pa 3
h
24
Ca.
.'.
C =
M.a
2
Pa 2
6
i^a
24
CONTINUOUS
Substituting,
'-SSAMS.
101
dy
Px 2
lX
wx 3
6
M^a
2
Pa2
6
wa 3
24
dx~
and
M/Y2
.
~2~
,*/
D/y*3 // X^
^ 'jpy UUJU
1
JL
P/Tf^'Y* C6 Ju
1/1/7 Cc/C*
*(/
"7*
From
(1), if
we
let
a,
we
get
in
terms of
lt
or,
M
Now
if
= M, + Pa ^f
jfc
(6)
we imagine the beam reversed and use Q for the origin, we can in the same way find the equation for bending moment, slope and deflection; for the part of the beam
between
Q and R and
over
slope and deflection will be the same for both can therefore equate these branches of the curve.
moment,
if
values
we
substitute x
We = a in
equating we get
for the left branch,
M
M.a
+ Pa
-^ = M =M
= s,opeover/J
and reduce we get
2
+ Qa
-^,
,
(7)
Pa 2
wa 3
.. i-L + -Li..
(8)
If
we
Q and P from
equation
//
1
1
(7)
in equation (8)
M,a +
This
is
(a
a,)
3 a,
7/V7 ^
7/5
"^
(9)
known
moments, and
by using
get as
different sets of three consecutive supports we can many equations, less two, as there are supports.
102
STRENGTH
-Q&
MATERIAL.
From our knowledge of cortditkms at the ends of the continubeam we can get two more equations involving the moments over the supports, and thus having as many equations as there are unknown quantities we may find all the
ous
supporting forces.
For example,
equal intervals
length.
let
the
beam
(9)
of Fig. 43
be supported at
Ibs.
per unit
From equation
or,
(1)
(2)
(3)
is
zero
at
M,
(3)
Substituting,
we
and
(1)
From
(6),
using the
first
three supports,
3 wo?
wa 2
equal to the change in S. F. at the second support. is due to the load to the left of the the and is P wa, positive part is given by the equasupport
is
Now Q
CONTINUOUS BEAMS.
tion
103
M =M
3
+ QR X a ft
of the
two parts
gives
Q =
wa
In the same way R = f | wa, or from symmetry we know S = Q and T = P, so the total load less (P + Q + T + S)
R, from which
R =
f f wa.
Examples
1.
continuous
beam
per
loaded with
Ibs.
ft.-run.
the
beam
is
38
ft.
long,
what
the supports?
Ans.
P =
3 w.
Q=
43
w.
5
of square section to span four openings of 8 ft. each, the total load per span being 44,000 Ibs. and the greatest horizontal fiber stress not to
2.
steel
beam
in.
3. Find the depth of a steel beam of rectangular section twice as deep as broad, to span three openings each 12 ft. wide, the total load on each span being 6000 Ibs. and the
greatest fiber stress allowed being 12,000 Ibs. per sq. in.
Ans.
4.4 in.
4. A continuous beam of three spans is loaded only on the middle span with a uniform load. What are the sup-
porting forces?
wl
Ans.
At ends
20
104
5.
STRENGTH OF MATERIAL.
= 268.9
in inch-units, is
36
ft.
long and spans four openings, the end spans being each 8 ft. and the middle ones each 10 ft. Find the maximum B. M.
of the
beam.
a
make
Ans.
If the 6. A continuous beam carries a uniform load. end spans are each 80 ft. what will be the length of the middle span in order that the B. M. at its middle may
ft.
How much
ins.
work
is
done on a beam 10
ft.
long, 10 ins.
deep and 8
per ft.-run?
Ans.
Work =
CHAPTER XL
COLUMNS AND STRUTS.
a prismatic piece of material, several times its than greatest breadth, is under compression, it is longer called a column or strut; a column being such a piece placed
57.
vertically
When
and carrying a
static load,
and
is
all
others being
struts.
column or
.strut of material
which
not homogeneous,
or one on which the load does not act exactly inthe geometric For mathematical axis, will bend or buckle.
we must assume our material homogeneous, and instead of assuming a slight deviation of the line of action of our load from the geometric axis, we will assume that the column has first been bent by a horizontal force, then such a load applied to its end as will just keep it in the bent form after the removal of the horizontal force. The assumptions we make will be three: (1) the column
investigation
fectly
Fig. 47.
perfectly straight originally; (2) material perhomogeneous; and (3) load applied ex-
These actly over the center of the ends. conditions are never exactly fulfilled in practice, so a rather large factor of safety must be applied.
Eider's Formula for Long Columns. We will choose column with rounded or pivoted ends, so that they will be free to move slightly as the column is bent. Let
58.
Fig. 47 represent such a column, held in the bent position by the load W. Let the origin be at the center of the column,
the axis of
vertical
and that
of
Y horizontal
is
the maxi-
105
106
STRENGTH OF MATERIAL.
deflection,
mum
and
?/
section
From
Art. 43
we have
HH
is,
from the
figure,
M
d
==
W(d -
y),
^ = Ti
grating,
(8
y) -
and
inte-
we
get
now
is
is
tangent to the curve of bending being parallel to the axis of X at that point, therefore the constant of integration, being
this tangent, is zero.
_Jw a
-i-r;
which integrated gives
(2)
C2
is
zero, for
where x
0,
and cos~
1=0.
107
when x
=,
we
get
have y
equation
(2)
we
cosine
is
zero
is
El'%'
from which we get
'El
"F
which
is
we
cos,
A column loaded with as per the above formula will just retain any deflection which may be given it, therefore this value of is called the critical load, for the column will
straighten out
if
load, and for any increase it will keep on bendThis is the load then ing until it breaks.
which puts the column in neutral equilibrium. The bending of columns is perfectly uniform, so we can derive from the formula of the preceding article, which is for a column with rounded
or pivoted ends, the formula for columns with one or both ends fixed. Let Fig. 48 represent
the elastic curve of a column with both ends fixed. There will be two points of inflection, B and D, and as the bending
108
STRENGTH OF MATERIAL.
is perfectly uniform these points will be at quarter the length of the column from the ends. The part will represent
BCD
considered in the preceding article, so the critical load of a column with fixed ends will be the same as for a column of half its length with
we
pivoted ends,
or,
The part BCDE of Fig. 48 would approximately represent the elastic curve for a column with one end (E) fixed ; so the
critical load for it
of two-
is
same
vertical line.
been shown by experiment that when the length of a is greater than 100 diameters the theoretical values are pillar closely approached, while with shorter lengths these values
are
much
too large.
Columns having flat ends, if the ends are prevented from lateral movement, are considered as having fixed ends. 60. As Euler's formula is applicable only in the case of
very long columns, another formula has been obtained in different ways by several different writers, which gives more Obviously a column may by crushing alone, in which case the = fA, where / is crushing strength would be load crushing For of the material and A the area of the cross-section.
accurate results for short columns.
be so short as to
fail
W must
is
lie
Eider's formula.
stress
109
',
this
due to bending, the maximum stress will be Pi + p2 must not exceed the strength of the material, so for the
limiting stress,
If
/= p +
1
p2
is
pl =
-.
A.
The equation
of bending,
p
<y
=M
,
gives us
p2
= My
,
remem-
bering that y in this formula is the distance from the neutral plane to the extreme fiber of the section,
_W Z
From
Fig. 48,
if
My
~T
deflection be d,
the
maximum
we have
--
Wd, and
we
have d
in this
=
;
(the constant
is
always a fraction, so
may
be put
equal to
way) substituting these values and remembering / is A multiplied by a constant squared, or, / = Ak 2 we have
,
_
from which
W
A
Wl 2 y_W
cyl
72
A
Af
W
This
is known as Rankin's formula for columns and struts with fixed ends. 61. We see that when I approaches zero, in the above
formula,
will ap-
110
STRENGTH OF MATERIAL.
of Art. 60
is
The formula
for a
column or
is
ends; if both ends are rounded or pivoted, value of c by 4; if one end is rounded, c
we must
divide the
2,
divided by
so
Flat ends:
W= W=
W=
c
Af
2P
dfc
2
Af
4/
and
/,
Hard
steel
69,000 48,000
36,000 80,000
7,200
Ibs.
per sq.
in.
20,000
Structural steel
"
30,000
"
" "
Wrought
Cast iron
iron
36,000
6,400
3,000
Wood
Examples:
hollow cast-iron column, fixed at the ends, is 20 ft. high and has a mean diameter of 1 ft. It is to carry 100 tons. Factor of safety 8. What is the thickness of the
1.
metal? Ans.
2.
1 in.
What
is
ft.
Ans.
30 tons, nearly.
Ill
the crushing load of a cast-iron column having flat ends, being 15 ft. long and 6 ins. in diameter? Ans. 311 tons.
What
is
ft. long, supports a load of 15 tons. square what must be the side of the square, allowing a factor of safety of 10? Ans. 9.25 ins.
4.
A wooden
strut, 12
If
the section
is
5.
flat
ends
is
20
ft.
long, 10 ins. outside diameter, 7 ins. inside diameter. load will it carry?
What
Ans.
6.
550 tons.
solid steel
ft.
is
6 ins. in diame-
ter
and 37
long.
What
load will
it
bear?
Ans.
7.
90,000+
Ibs.
and
carries a load of
What
square wooden column with fixed ends is 20 ft. long 9500 Ibs., with a factor of safety of 10. is the side of the square? (Euler's formula.)
5.769
ins.
Ans.
8.
If in
example 2 the
pillar
breadth double the thickness, what sectional area would be required for strength equal to that of the pillar of example 2?
Ans.
9.4 sq. ins.
CHAPTER
XII.
We
have thus
us now investigate the methods for finding the stress on any of the parts of a loaded structure This can be done graphiconsisting of several members.
pieces of material;
let
by calculation, and both ways will be considered. understand by the word structure anything built of separate parts, called members, between which there is to be no motion. Each member must be strong enough to withstand all the forces to which it will be subjected withcally or
We
will
External forces acting on a structure are (1) the weights members; (2) the loads carried, such as the traffic
roof,
weight
The
crane, etc.; and (3) the supporting forces. internal forces are the resistances offered by the mem-
by a
bers to distortion.
The external forces acting on any member of a structure are its weight, the load and supporting forces and the forces
exerted on
it
by other members.
use of the following rules for the equi-
We
(1)
shall
make
librium of a structure:
and
internal, acting
on
balance.
any imaginary
113
forces
complete section of a structure must balance all the internal on the same side of the section. (4) The algebraic sum of the moments about any axis of
the forces both external and internal on one side of any
section through a structure must equal zero. All members of a structure are held together
all
by
joints.
the word frame will be meant a structure which has Frames cannot actually exist, for there frictionless joints.
By
is
closely
always frictional resistance; however, many structures approach them, and whatever error there is may be
considered
somewhat
A member
if
of a structure
is
called a
tie ;
joint, the stress in the members is considered as acting at the center of the joint, each member necessarily having a joint at each end to keep it in equilibrium, and obviously the stress in the member will be of the same amount through-
out and
will act
end being
along the axis, the effect on the joint at one on the joint
joint, for
equal in amount and opposite in direction to the load on that otherwise the joint could not be in equilibrium.
All frames will be considered as loaded at the joints.
In
the case of continuous loads, such as the weight of a member, the equivalent parallel forces will be considered as acting at the joints; thus a uniformly loaded member would be considered as having half the total load acting at each end. 63. As a simple frame we will first consider a common
triangular roof truss in which the weight of the roof itself forms the load, say w Ibs. per ft.-run on each rafter. On the
member
and
AB
there will be
half at B.
On
the
114
which half
STRENGTH OF MATERIAL.
will act at
B and
half at C; so that at
there will
w
be a load of
(a
b) Ibs.
Now
will have to sustain this whole load, and their value obtained just as we found it in the case of loaded beams, the moment arm of the load at B being the projection of the member AB on AC, or BC on AC, the lengths being
is
and Q
etc.
Now
at A,
and
of the supporting
are identical, but the directions of the forces are opposite, so we can use their
difference for
without mak-
w&
ing any change in the stress of the members of the structure (this being the resultant of the two forces) and thus
..
.Q
ex-
(It is
convenient in calculating the supporting forces to ignore the load which acts on the lower end of the rafters.) We
have
stress
now
in
to
find
the
members and AC, and we AB, BC, can do this (1) by calcuthe
IP
and (3) by a Fig. 50. Each method. graphic of these methods will be explained in the three following artifor with cles, but each method must be known thoroughly, it is necessary to employ more than one frames complicated Before proceeding we will of the methods to get results.
115
introduce a system of lettering which will be convenient, and which should be used in all cases. Referring to Fig. 50, the external loads at the ends of each member have been
indicated by arrow-heads. After each one of these external loads we place a capital letter, and in each space made by the members of the frame we place a small letter. To
indicate any force we write or mention the letters on each side of it; for example, the left supporting force is EA, the
right one DE, the load at the peak BC, etc. forces will all have at least one small letter,
The
internal
may be
small;
that in the
member
Bb, the one inclined to the right Cc, etc. this method we letter the forces, which will be found
for finding
As an
illustration,
we
will
find
members
rafters of
1120
20 and 15
per
ft. -run
ft.
respectively,
rafters.
on the
and which has a load of 100 Ibs. The loads, additional dimen-
sions and supporting forces as indicated in Fig. 51 are found by the methods of the preceding article,
cos
sin
ft
-
= |, =
116
STRENGTH OF MATERIAL.
For the equilibrium of the joint at the peak the sum of the components of the stresses Aa and Ba must be equal to the load 1750, but must act in the opposite direcvertical
tion; therefore,
Aa
cos
cj)
+ Ba
cos
1750, or, f
Aa +
Ba =
1750.
(1)
Considering the joint at the right support, the sum of the horizontal and of the vertical components of the forces
acting there
must be
compo-
nent of
equal Q, and the horizontal component must equal the stress Ca. Resolving, horizontally,
Ba must
Ca
Ba
cos
(f>,
or,
Ca
\ Ba.
(2)
Vertically,
Ba
sin
=
</>
1120, or, f
(1),
Ba =
1120.
.'.
Ba = 1400
Ibs.
Substituting in
|
Aa +
1400
= =
1750.
.'.
Aa =
1050
Ibs.
Substituting in
(2),
Ca
1400
840.
/.
Ca
840
Ibs.
obvious that the stresses Aa and Ba will be comand that Ca will be tensile, but in many cases it is pressive, not obvious, and with the graphic method will be shown a
Now
it is
way
Taking the joint at the ^accurately distinguishing. acts the external load down, so the resultant of the peak, stresses Aa and Ba must act up; to do this they must push
of
a stress then which pushes on a joint is comone which pulls is tensile. and pressive This method of finding stresses will hereafter be called the method by calculation, to distinguish it from Hitter's method. This may be called the method 65. Hitter's Method.
on the
joint;
of sections, as
it
117
and
if
possible
of all the
The moments may be taken about any axis, we choose an axis about which the moments unknown stresses cut by the section except one
disappear.
cle
We
arti-
by
this
method and
Q=1120
Fig. 52.
HH
as
shown
in Fig. 52.
If
now we
take
moments about
the joint at the peak, the moments of the stresses Aa and Ba will be zero and we will have to the left of the section only the
external force
and the
stress
right the external force Q and moment of the 1750-lb. load about the joint at the peak.
Ca
Taking moments, then, the perpendicular distance from the peak to the stress Ca being 12 ft., and that to the line of action of the force P being 16 ft., we have
630
16
- Ca X
12, or,
Ca
840, as before.
Taking moments about the joint at the right support will eliminate the stress Ca, and still working with the forces to the left of the section we have
630
25
= Aa X
15, or,
Aa =
1050, as before.
Care must be taken to use the perpendicular distance to the We have used 15 in this case line of action of the forces.
118
because, the peak.
it
STRENGTH OF MATERIAL.
will
is
right-angled at
it
To
is
Ba we must
the
the section
let
members through which the section passes. KK and take the moments about an
We
will use
axis through,
us say, the point L. (We may use any point.) Here the perpendicular distance to the stress Ba is 7.2 ft., and to the supporting force Q it is 9 ft.; so
1120
= Ba X
L
7.2, or,
Ba =
1400, as before.
Instead of choosing
just as well
for the
axis of
moments, we could
left
supporting force
25
= Ba X
20, or,
Ba =
1400.
will
members
desired,
and
is
frequently necessary in
represented in amount and direction by the consecutive sides In all frames the forces acting at the of a closed polygon. in and the line of action of must be equilibrium, joints
member in which they are found. All the external forces taken in order around the frame will form a closed polygon, because by our first rule for the equilibrium of structures they must balance. Draw carefully a diagram of the frame
at each joint indicate by an arrow-head the load, if there be one; indicate also the supporting forces. This figure is called the frame diagram, and will be denoted by F. D.
and
of forces acting at
119
will
and
it
be de-
Having determined the amount and direction of the external forces, plot them to a convenient scale, forming the external force polygon. In case the loads are all
noted by R. D.
vertical, as in the
example
polygon
is
R.D. c
Q=1120
F.D.
i_LB
Fig. 53.
1750
Ibs.
being represented by
force Q,
acting up,
by BC, and
by CA,
of
same distinguishing
rafter itself, so
letters in the
R. D. as in the F. D.
is
Now
from
polygon draw a
B draw a line parallel to the righthand rafter to represent the line of action of the stress Ba. The intersection of these two lines will be the point a, and if we connect C and a, the line will be found to be parallel to the tie rod of the frame, and Ca will represent the stress in the tie rod to the same scale as that used to plot the external force polygon, just as Aa and Ba will represent the
stress in the rafters.
This figure
is
120
STRENGTH OF MATERIAL.
lines
do represent the stresses may be and ABa are equal respectively to and 6 of the F. D. by construction, and as AC is to scale = 630 X f = 1050; equal to 630, Aa will equal 630 sec - 1120 X I =1400; and Ca will Ba will equal 1120 sec equal 630 tan </>, or 1120 tan 6, either of which will give 840. The results are then the same as those obtained by other methods. Of course, if the diagram is drawn accurately, the stresses may be measured off to scale.
proved, for the angles
<j>
BAa
<
To
forces acting on the joint at the peak are the load B and the stresses Aa and Ba. If we pick these lines out on the R. D., they will form the polygon of forces (in this case a
triangle) for the joint at the peak. Knowing the direction of one of these forces, we will indicate it by an arrowhead;
for
example, we know
For the equipointing down on the line AB of the R. D. librium of the joint at the peak the direction of the forces
if we suppose the arrowhead around the sides of the polygon for this joint, starting in the direction in which it points. When on each side it will indicate the direction in which the stress for the corresponding member acts on the joint, and remembering that a push indicates compression and a pull tension, we can at once state what kind of stress exists in any member The arrowheads are marked in the R. D. acting on the joint. of Fig. 53 for the joint at the peak. They have been indi-
of
acting on to
it will
be indicated
AB
move
in order
cated for a single joint only, because if we consider any other joint involving the stress of any of the members acting on this
in opposite directions.
one we would have two arrowheads on the same line pointing This at first glance appears to be incorrect,
stress in
any member
acts in opposite directions on the joints at its two ends, and that we would n<ft be working .with a different joint, the
itself
if
we con-
121
sider the joint at the right-hand support, we will find the in the R. D., arrowhead for the stress Ba pointing toward
which we know to be correct, as the right-hand rafter compression and therefore pushes on this joint.
is in
Examples
1.
truss
is
each
with 250
Ans.
2.
the peak?
A beam
15
ft.
long
is
and a
2
ft.
strut at the middle forming a simple triangular truss What is the stress on each member when loaded deep.
Strut, 2 tons; tension rods, 3.88 tons; thrust
on the
small brow, 6
ft.
ft.
broad and
ft.
a load
of platform.
It is
deep.
member.
Ans.
Strut,
3000
5000
Ibs.
4. The rafters of a simple triangular roof-truss slope 30 and 45; span 10 ft.; the rafters are 2^ ft. apart, and the roof weighs 20 Ibs. per sq. ft. Find the stress on each member. Ans. Stress on tie rod, 198 Ibs.
small brow, like that of example 3, 4 ft. broad and a load of 100 Ibs. per sq. ft. of platform. load of 1 ton passes over the brow; what is the stress in the
5.
members when
Ans.
Compression of
122
STRENGTH OF MATERIAL.
6. The tie rod of a simple triangular roof-truss is 25 ft. long and inclined at 30 to the horizontal. The supports are at its ends and the rafters from its ends are 20 and 15 ft.
Ibs.
per ft.-run.
Ibs.
What
is
the
in
rafters,
148+
and 512 +
Ibs.;
tie
174+
CHAPTER
FRAMED STRUCTURES
67.
XIII.
Continued.
to tie
has flooring laid on the horizontal ties, in addition to the load on the rafters, so that when divided at the joints the
load will be as shown in Fig. 54.
R.D.
Fig. 54.
^
and from
it
Aa =
Bb
ba
10 tons C. (compression).
8 \/2 tons C.
Da =
To
get the stress Aa, for example, by the method of sections; taking a section HH, and moments about the joint at the
we
right-hand support, using forces to the get, x being equal to 16.8 ft.,
left of
the section,
PX
28
= Aa X
x, or,
Aa =
123
10 tons, as before,
124
STRENGTH OF MATERIAL.
calculation
it is
The method by
other methods
is
complicated.
" 68. A King-Post Truss," slope of rafters 45, and having struts to the middle points of the rafters as shown in Fig. 55,
E
F.D.
Q L.
Fig. 66.
has a load of 8 tons uniformly distributed on each rafter. Find the stress in the members. The loads are as shown in the F. D. The R. D. gives us:
Aa = Dd =6 Wtons
Bb
C.
by method
joint
of sections,
calling
take section
at
peak,
span S.
S S Q X - = Ed X 2
2
69.
'.
6 tons, as above.
sustain a horizontal wind pressure of 6 tons, uniformly distributed on the right-hand rafter. Putting in all the loads
they would be as shown in Fig. 56, and the walls would have
to sustain in addition to the vertical load a lateral pressure The resultant of the loads is not now vertical, of 6 tons.
FRAMED STRUCTURES.
125
therefore our supporting forces will be inclined. Obviously, the effect is greatest on the left-hand support, so the inclination of
will
Calling the
R.D.
Fig. 56.
P and Q make with the vertical and 6 reand the span S, and taking moments about the spectively,
angles that
(j>
QScos
=-
Sf
S>
-X4-f-f
2
.-.
X4 + 2S--X
6=
6.5,
42
Sf
3 -
-X
Sf
1.5.
cos
and,
cos
$=
9.5,
which shows the sum of the vertical components of the supporting forces to be equal to the vertical loads as
be, also
it
should
sin
<j)
+ Q
sin
6 tons,
126
STRENGTH OF MATERIAL.
\
or the horizontal components equal the horizontal loads. Proceed now with the external force polygon to and including the force HI. The next two forces are the supporting forces.
We know the
line I A.
external forces give us a closed polygon, theretwo supporting forces is the dotted
We know
the
sum
of the horizontal
components
of
the two supporting forces is 6 tons, so we will draw a line parallel to the direction of AB, BC, etc., at a distance from it
equal to 6 tons as per our scale. We also know the vertical component of the force P is 9.5 tons, so laying off from A toward D the distance 9.5 per scale, if through this point we
draw a horizontal line, the point J must be somewhere on it, and also somewhere on the first line. Therefore J is located at their intersection. Connecting J and / we find the line is vertical and therefore that the supporting lorce at Q is vertical and equal to 6.5 tons. Connecting J and A we have the supporting force P both in magnitude and direction, and find it equal to 11.236 tons and at 32 16' 32" with the vertical. Of course practically the right-hand support would sustain some of the horizontal load, due to' friction and the way the
roof
secured to the walls, but if the left-hand wall is built strong enough to take all the horizontal effect our structure will be safe. As we can always resolve any oblique force horiis
and vertically, we may assume that the supporting on the side from which the horizontal component comes, wall, has a roller on its top, so that the supporting force on that side will have to be vertical.
zontally
Proceeding now, we complete the F. D. by putting in the supporting forces, then finish the R. D. as shown in the figure and find the stresses to be as follows:
Ba =
Cb = Gd = ba = Ja =
7.5 \/2~tons C.
EC
be
cd
2 \/2~tons C.
1.5 tons T.
Jd
= = = =
4 V2~tons C.
5.5 tons T. 3.5 \/2 tons C.
3 tons T.
FRAMED STRUCTURES.
To
127
get the stress cd by the method of sections, we must know and use the forces to the stress Jd, then take a section the right of the section taking moments about the joint at the
KK
peak.
HH,
rr
O
1.5
^X-=6.5X '--2X-or,
X-,
Jd
now, using section
cd
3 tons
T.
KK
(a section
X
2
=-
V2
= Jd X 2
L5X
S
6<5
2~
S
-,
from which cd
70.
3.5 \/2
C., as before.
is loaded, as shown in Queen-Truss the F. D. of Fig. 57, with unequal loads over the two struts. With this loading the R. D. is as shown. The stress in the
An
inverted
"
"
diagonal
is
tension.
If
i.e.,
R.D.
Fig. 57.
for
for AB, the stress in the diagonal would BC, and have been compressive. If the diagonal member had been omitted, the R. D. would not have been a closed figure
128
STRENGTH OF MATERIAL.
(except in the case of equal loads over the struts), showing that the frame would not then be in equilibrium. The
diagonal member is then necessary in bridges of this kind, because of the traveling loads they must carry.
71.
Bollman truss
is
24
ft.
long, 3
ft.
Proceeding with the R. D. we draw the external force polygon, the direction of
24 tons
I
/
'
24 tons
i
<B
C
B.D.
F.D.
R,D,
Fig. 58.
the stresses Aa, Bb, Cf, Dg, De, DC, and Db. Here we have to stop, for we have none of the points represented by the small letters. The simplest way out of our difficulty will be to find the amount of stress in one of the members by the
method
of sections.
about the point where the two long tension members cross (marked with circle) and working with the forces to the left
of the section,
Bd X
Laying
24
12
24
4, or,
Bd = 85J
tons.
point R. D. shown.
d, after
72. The force diagram of Fig. 59 shows an girder of four panels with a uniform load over the lower platform. Having drawn the external force diagram, the stress Ea
lie
somewhere on a
hori-
FRAMED STRUCTURES.
129
a must
zontal line through E; the stress Aa being vertical the point Therelie somewhere on a vertical line through A.
of the R. D., or fore the point a coincides with the point the stress Ea is equal to zero with this loading. The memis necessary to the bridge, however, for even if it did not support* part of the platform it would be required to keep the frame from turning about the upper joint over the left support. The stress Bh also proves to be equal to zero in the same way. Proceeding now we get the R. D. as
ber
shown and
is
also zero.
In this case,
WWW
4.
4.
F.D.
R.D.
Fig. 59.
too, the
of the top
member boom
it
is
necessary, for with a joint at the middle the stresses Ad and Ae being compressive
would cause
to turn,
and without
cause
in
the joint
it
the necessary
length of the
member would
stresses
now
the R. D. the
the
obtained.
effect of
In designing
to buckle.
taining its own weight must be strong enough to sustain the stresses caused by the loads which cross it. The method of constructing bridge platforms (the planks or railroad
being placed across stringers between joints) puts practically all the bending stresses on the horizontal parts and all the shearing stresses are sustained by the diagonals (the
ties
shearing stress being equal to the vertical component of the stress in the diagonal). Therefore, considering only the
130
STRENGTH OF MATERIAL.
weight of the structure, the diagonals at the left of the middle are inclined to the left and those to the right of the middle to the right, because those directions put them in
(For the same load a rod in tension requires less area than one in compression, hence less If we consider a bridge material, less weight and less cost.) of this kind with a concentrated load moving across it,
tension.
cross-sectional
referring to Fig. 41, Art. 50, the load entering the bridge at the left end, we see that positive shearing force predomi-
nates at the left end and negative at the right, the curve in this figure being for the traveling load only. Therefore the total shearing force due to both the weight of the structure
at
and the traveling load will change sign from plus to minus some position of the traveling load other than the middle
r
of the bridge. Obviously, this w ill change the kind of stress in the diagonal at this point, and the dimensions of the
made such as to sustain the new we must put in a second diagonal inclined in the opposite direction. The latter method is used because of
diagonal here must be
stress, or
pression,
the increase of weight necess-ary with a diagonal under comand also because a tension rod is less expensive
These extra diagonals are called above is the reason for counterbracing some of the middle panels of N girders.
ff_
\A
c
R.D.
Fig. 60.
73. A Warren girder, angle between members 60, carries uniform load on the lower platform as shown in Fig. 60,
FRAMED STRUCTURES.
The R. D.
easily
article
131
is as shown, and the stresses in members are obtained from it. The remarks of the preceding
on counter bracing apply equally to this girder. If vertical lines through each joint and call the part between two vertical lines a panel, the calculation will be just the same as for the N girder.
we draw
Examples:
A King- Post Truss, slope of rafters 45, has struts to 1. 2 w\ the middle point of the rafters as in Fig. 55. = in 4 w. Find the stress each member BC 3 w, and
AB=
CD=
by the method
the kind.
2.
of sections
and
also
bridge
is
with the platform on the lower boom, which is of four divisions. Forty tons are uniformly distributed over the left half Find the stress in each member, stating the of the bridge.
kind.
3. A bridge, 60-ft. span, is supported by a pair of girders of 6 panels, height 8 ft. The platform is on the upper boom and carries a uniformly distributed load of 12 tons on
the
left half of
the bridge.
Find
stress in
each member,
roof
is
horizontal
member
constructed of two rafters at right angles; a connects the middle points of the two
rafters; the
ends of this member are connected with lower ends of the opposite rafter. The joints of the peak and the middle of each rafter carry a load of 1 ton. Find the stress
in each
member and
the kind,
if
the span
is
20
V2
ft.
5. A .bridge of 60-ft. span is constructed of a pair of Warren girders; the upper boom, which supports the platform, is of 6 divisions, the lower boom of 5. The platform is also
132
STRENGTH OF MATERIAL.
supported by struts from the joints of the lower boom, and carries a load of f ton per ft.-run. The supporting forces
are at the ends of the upper boom.
in each
member by
the R. D.
bridge, 96-ft. span, is supported by a pair of N with 8 panels 9 ft. deep. The platform rests on the girders boom and is loaded with 96 tons uniformly distribupper
7.
uted.
8.
stress in
each member.
bridge
example
7.
What
braced?
9. A Warren girder, 9 The top boom is of three
ft.
long,
divisions, the lower of two, but has a horizontal strut from the inner joint to the wall.
With a load
two
joints of the
Suppose the load of example 9 at each of the other upper boom, and thence deduce the results
CHAPTER
XIV.
Continued.
FRAMED STRUCTURES
74.
An example
With
all
of a scissors-beam truss is
61.
With
roof-trusses
shown in Fig. shown is readily obtained. the loads due to wind pressures must
We
this
may be
Fig. 81.
done by resolving the wind loads into their horizontal and components (Art. 69) and considering the total It may also be done effect as sustained by one of the walls. by combining the loads on each joint and using the resultant load on each joint in drawing the external force diagram, or by finding the R. D. for the vertical and inclined loads separately and algebraically, adding the stress due to each for the total stress in the members. 75. When the external loads and the members of a strucvertical
ture are
in the
all in the same plane we can always find the stress members by means of the reciprocal diagram; for
133
134
STRENGTH OF MATERIAL.
example, the F. D. of Fig. 62 shows a common crane carryThe external forces are as shown, the ing a weight W.
forces
EC
and
DA
overturning,
their value
F.D.
R.D.
Fig. 62.
moments.
The
force
can be combined
dotted line CA.
if
is equal to the weight. The exa rectangle. The forces CD and DA desired, their resultant being equal to the is is
CD
The R. D.
stresses
and from
it
the
are
usually arranged so that the load is lifted by means of a tackle, the hauling part of which leads down to a drum secured somewhere along the crane post. The stress in
where n
is
the
number
of
FRAMED STRUCTURES.
135
parts of rope between the two blocks of the tackle) augments the compression in the jib and reduces or increases the tension of the jib stay, depending on whether the drum
is
above or below the point where the jib joins the crane These additional loads on the members must be post. taken into account. This can be done by introducing an
Fig. 63.
and equal to
W
n
will
DA
of
be somewhat inclined.
external force diagram
forces.
To draw any
we must know
all
In this case we know only and the tension of the rope. We can,
136
STRENGTH OF MATERIAL.
however, find the force CD by taking moments about the lower end of the crane post, as
W X-x
whence
W
n
-X
+ CD X -
y,
CD
The
to
force
W (nx
ny
z)
DA
is
DA
of Fig. 62
and the
Except the resultant now we know all the external forces, so our external force polygon is A BCD, the line DA representing the amount and direction of the supporting force. The R. D. is now readily found to be as shown, and the
stresses are easily obtained.
76.
members
loading
A frame having just enough Incomplete Frames. to enable it to retain its shape under any kind of
Frames may have more members than is complete. necessary, under which circumstances some of the members are redundant, but frames without a sufficient number of
members
to enable
them
under
all
circumstances, with any kind of loading, are said to be When frames are incomplete we will find the incomplete.
reciprocal diagram for different loadings giving intersections for the same point in two or more places; as, for example, we know the mansard roof truss, shown in the
F. D. of Fig. 64,
is
is
nothing to
prevent the three upper joints from turning. Suppose = 3 then drawing the R. D., we find the point a falls l in two different places on the horizontal line from E] this is clearly imposible, for the stress Ea cannot have two had The frame then is not in equilibrium. If values. on have been a's would not the two to not been equal W%
line.
We
FRAMED STRUCTURES.
137
that this frame would appear from the R. D. to be comof the points a to be correct, plete; as, assume either
it
draw
F.D.
Jt.D.
Fig. 64.
R.D.
Fig. 65.
Ba and
Ca.
These
which would put the frame in equilibrium, but the first puff of wind would change the loading and cause the frame to
collapse.
138
STRENGTH OF MATERIAL.
To make this frame complete, at least two additional members are necessary, for there are three joints which are
likely to turn.
65, will
The two additional members, shown in the F. D. of Fig. complete the frame, as is shown by the R. D. being
a closed figure and possessing no duplicate points, no matter what loads are applied.
this, as
be made clear
if
we
D.'s.
frame, then, to be complete, must remain in equilibrium under any loads which do not stress its members
beyond the elastic limit. 77. We have been considering in all these structures the When stress which acts along the axis of the member.
members are not straight, or when they carry loads at points other than the joints, the stress on them is not simply a thrust or pull in the direction of the axis, but
includes a bending and a shearing action. Fig. 66 shows a vertitwo intermediate with of structure member a single
all these forces along and perpenthe member, components perpendicular to the member will cause bending and shearing stresses in it, cos 6, as the cos and and using these components,
cal loads.
If
we
resolve
dicular to the
FRAMED STRUCTURES.
loads,
139
and
cos 6 and
cos
we
Chap-
VI and VII.
These intermediate loads cause also a stress along the member, and this stress (the thrust T shown) sin d, and between P and W^ will be equal to between sin 6, or sin and it will be the sum of and t this member is the reaction sin value which + of (W TF,) 0, on the one next below it. causes an equal reaction on the Obviously (P + Q) sin member next above it. Just here we can show that our assumption that the loads act on the joints is correct, for the action on these joints of the structure, considered as a whole, caused by this member is equal to a force P acting downward at the left end and a force Q acting downward at the right end; and obviously without error we can use these forces P and Q
axis of the
When (reversed) instead of considering the separate loads. member carries a uniform load, as is usually the case, the
values of
is
and
We
in
members
have not considered the bending and shearing stresses of a structure until now, because they are com-
paratively small. A. compression member, being necessarily large to sustain the thrust due to all the other members
affect it, will be little inconvenienced by the small due to the bending and shearing caused by its own load, and the tension members, in properly built structures, will have only their own weight to cause bending and
which
stress
shearing.
Examples:
1.
is
carried
by a
scissors-
truss
whose
12
ft.
90.
Two
members
140
STRENGTH OF MATERIAL.
The
third
is
horizontal
and
2. In example 4, Chapter XII, find the shearing force and bending moment and thrust for each point of each rafter and draw curves showing results. 3.
3,
4 and 5
ft.
long, has
the
5-ft.
ft.-run,
10 Ibs. per and the inclined sides each have 50 Ibs. at the
members weigh
middle.
ing
4.
span 63
suspension bridge carries a plaftorm 8 ft. wide, ft. suspended by 6 equidistant tension rods. The
lowest joint is 7 ft. below the highest, and the cable is formed of 7 straight members. It carries a load of 1 cwt. per sq. ft. of platform. Find the sectional areas of the
cable members, allowing a stress of 4 tons per sq. Is this frame complete? material.
in. for
the
Ans.
sq. in.
5.
From
left
in.;
middle, 3.47
A mansard
3 tons on the
roof truss, as in Fig. 65, carries 1, 2 and The rafters make left, top and right joints.
Find the
stress
6. A crane, as in Fig. 62, has the tension members Ac The members be, ba and aC are horizontal and 6 ft. long.
respectively
8,
6 and 4.5
ft.
long.
Find the
stress in
each
a weight of 12 tons.
MISCELLANEOUS PROBLEMS.
78,
Concrete
is
much used
present, and though its tensile strength is very low compared to other materials, the ease with which it is handled, transported and shaped, together with the fact
in building at
that
when
tory and
is
satisfac-
combustible, has
made
it
most
rather
N
difficult,
the changes they due to the different kinds of cement used and the different methods of mixing. Strength tests for the cement itself vary from 40 to 1000 Ibs. per sq. in. for tension and from 1100 to 12,000 Ibs. per sq. in.
considering
suffer,
n m n
for compression.
building the endeavor has been to subject the concrete to little or no tensile stress, but to have all that stress
In
all
sustained by the steel reinforcement, allowing the concrete to sustain as much as possible of the compressive stress.
Tests have shown the compressive strength of concrete to vary from 750 to 5360 Ibs. per sq. in. and the modulus of
elasticity to
units.
method of finding the moment of inertia of the section of a reinforced concrete beam is as follows: Assuming that
the elongation of the steel reinforcement is the same as for the concrete at equal distances from the neutral plane, which
141
142
will
STRENGTH OF MATERIAL.
be true
if
P steel = E'steel
and
Pconcrete
X extension
= ^ concrete X extension, =
E
s
'
or,
from which
Ps
E = TT PCs
EC
beam
rein-
forced
by three
If
steel rods
of the neutral
plane, N. P.
now we suppose
beam
to be entirely of
concrete and to retain the same strength and the same depth, we will have to broaden the section in wake of the steel rods
to conform with the fiber stress which that part of the section can now withstand. If y is the distance from the neutral
axis to an elementary area, dA, of the steel, the the stress about the neutral axis will be
E,
moment
of
yp s dA=yp c -fdA. EC
So,
if
the section
is
to be considered
homogeneous
(all
con-
the areas vary as the moduli of elasticor the of concrete which is equivalent to the present area ity, The equivalent concrete area of steel will be as E s is to E c
crete),
.
we must have
shown
in Fig. 68.
The
My
MISCELLANEOUS PROBLEMS.
7 being the
143
For
in.
moment
beam
of Fig. 67 to
be 6
in.
wide, 10
square with their deep, and the reinforcing rods to be lower faces 1 in. from the surface of the concrete. Let E 8
\ in.
be to
E c as
15 to
1.
half
5 at this part of the section due to the steel will be - / ins. of concrete at But there is, in addition to the steel, f ins.
Fig. 68.
V
and the depth
of the
ins.,
broadened part
will
have now all the dimensions of the equivasteel, or \ in. lent concrete section, from which we find that the neutral axis is close to 4.4 ins. from the bottom of the beam, and the
We
moment
is
about 626
in inch-units. It has been shown by experiment that small cracks appear on the tension side of a reinforced concrete beam as soon as
the fiber stress reaches the limiting tensile strength of the From this fact it is clear that practically all of concrete. the tensile stress
is
supported by the
steel reinforcement.
144
STRENGTH OF MATERIAL.
this
With
all
of
the tensile stresses on one side of a section must equal the sum of all the compressive
6
->!
stresses
on the same
If
side of the
section.
then
A
it;
is
the
known area
and
area
bx the
section
of
concrete
on
maximum
it,
we have, assuming
pressive stress to vary directly as the distance from the neutral plane,
Ap =
s
i pjbx.
(1)
We know
its
the position of the steel reinforcement, and calling distance from the top of the beam h, we have the sum of
the
moments
of the stresses
MISCELLANEOUS PROBLEMS.
145
can be found, because the change of length of the two mateWe have, therefore, the equations rials must be the same.
IPs
lp c
S
AE
S
A CE C
Pc
,
L = ps +
where
(2)
I is the length of the column, A s and A c the sectional Concrete columns areas of steel and concrete respectively. are usually made so short that bending does not enter into
the calculations, which is. the case when the column is not A difficulty in longer than twelve times its least diameter. investigating the bending of reinforced concrete beams lies
in the fact that the
modulus
of elasticity of concrete
under
compression decreases somewhat as the loads increase. This will evidently cause an upward movement of the neutral Several theories with different assumptions have been plane.
advanced, but the investigation of these beams may be conThe use of the sidered to be still in an experimental stage. equivalent section gives fair results. Another theory assumes
the stress in the concrete to vary as the ordinates of a parabola and that the moduli of elasticity for the different
stresses are those
79.
Poisson's Ratio.
is
piece of material
is
reduced somewhat, in addition to the change made in the length of the piece. This change of cross-sectional area is
quite marked if we stretch a piece of rubber because the elongation is great but with materials such as are used in building the change of cross-section is scarcely perceptible, for the
;
elongation is very slight. Tests show that the lateral expansion or contraction, due to compression or tension, bears a
Poisson's ratio.
This is known as constant ratio to the change of length. If then the extension per unit length, of a
is
e}
the length of
its
diameter, d,
146
will
STRENGTH OF MATERIAL.
be reduced an amount equal to ked, where k
Poisson's ratio
Steel
is is
the value
of Poisson's ratio.
for
297
Iron
277
340 357
Copper
Brass
If
and of unit square section, is under a and a compressive stress, R, perto the two axis on pendicular opposite faces, the total extension in the direction of the axis, is that due to the tensile stress plus that due to the compression stress, or,
a rod of length
Z,
total extension
= Fl E
kRl
H
80,
Stress in Guns,
We
=
97*
,
found in Art. 10 that the hoop under the internal pressure of S Ibs.
where
of the
metal and
metal was considered so thin, that the stress might be taken as uniform throughout the section.
is
If,
thick,
we cannot use
this
but
will
vary in some
way with
'
MISCELLANEOUS PROBLEMS.
147
readily seen to be the total pressure on an end divided by We will call this longithe sectional area of the cylinder. tudinal stress T and will assume it is uniform throughout
the section.
If
now we
element of volume within the material of the cylinder the element will be in equilibrium under the action of the longitudinal stress T, the hoop stress H and the radial stress R.
From the preceding article we have for a value of the total extension at the element in the direction of the axis of the
cylinder
e
= E
(T
- kH -
kR),
k being the value of Poisson's ratio for the material. Now, if sections remain plane while stressed, we may assume the
total extension
T
(1)
being constant,
we must have
H plus R equal to
a constant,
H + R=C.
Let Fig. 70 represent a right section of the cylinder of unit thickness (perpendicular to the paper) and let the circular element shown be of width dr. If we call the radial stress
at the inner surface of the element, R, the hoop stress, at the inner surface of the element, will be (Art. 10) equal to Rr. The radial stress, at the outer surface of the element, will be
dR, and, as the radius here is r + dr, the hoop stress, at the outer surface of the element, will be (R -f dR)(r + dr). The hoop stress over the sectional area of the element will
be (R
R +
dR) (r
dr)
Rr.
But we have
called the
stress
hoop
this
stress at
any
will
hoop
on
element
be H, multiplied by the sectional area of the hence we will have, the element being of unit element;
thickness,
or,
(R
rdR
Rdr
Hdr.
(2)
148
STRENGTH OF MATERIAL.
(1)
From
we have
H =C-
R, and, substituting,
rdR
+ Rdr=
Cdr
Rdr;
r,
we have
dR +
2 rRdr
Crdr,
d (r*R)
and, integrating,
Crdr,
where
is
From
we
get
and substituting
this value of
in (1)
we
get
.-->
Now the cylinder has an internal pressure of S Ibs. per unit area and an external pressure of S Ibs. per unit area, so if r2 we have R at the inside surface equal to S, and if r
l
S iy
and, sub-
and
+ SI=2
solving (5)
-T;
TV*'
(6)
and
(6)
we have
Ci
_r.VCS.-fl)
7*o
7*i
(7)
MISCELLANEOUS PROBLEMS.
and
149
C=
""
^f
1
'
^
2
S}
,
(8)
and
(4)
we
R=
and
r*S
-rSS
-
rW (,-)
,
r.'S,
r,'S
r.V,' (S,
S)
r-r .'-'
If there is
no external pressure, as in the cases of cast guns pipes, S will be equal to zero and our forl
and
equations (11) and (12) we see that the greatest stress at the inner surface of the cylinder, and here the total extension found by the method of Art. 79 must not exceed
is
From
and
It will be noticed that the found above do not take into consideracontraction of the material mentioned in the
If we consider this lateral contraction, the stress which would produce an extension equal to the total elongation found by the methods of Art.
preceding
article.
l
and
79,
call
we would have
H,
= H - kR -
kT.
modern
Putting in this
150
STRENGTH OF MATERIAL.
value for k and also the values of and R from equations (9) and (10), the value of T being found directly from the external and internal end pressures and the sectional area of the cylinder, to be
T=
we have,
after reducing, for the true
r,'S t
hoop
stress
-r,'S
4r,V(S,-S)
which
81.
the formula used for the hoop stress for naval guns. The guns at present used in the Built-up Guns. " " are known as navy guns; that is, they are built built-up of several pieces which are made separately. The inner is called the of it outside is the and outside tube, piece jacket,
is
The exterior diameter of the than the interior diameter of greater the jacket, the exterior diameter of the jacket a little greater than the interior diameter of the first hoop, etc. The protube
is
made a
little
cess
until
assembling consists in heating the jacket expands sufficiently just to slip over the tube, after which it is allowed to cool. In cooling the jacket contracts
as
it
known
and
pressure on it. The hoops are then put over the jacket in the same way. This way of securing the several parts together is called the method of hoop shrinkage, and obviously if two parts are assembled by this method, the inner one will be under hoop compression and the outer one under hoop tension. Considering a cylinder formed of two parts, let the radii after assembling be rz r2 and r lt the least Let R 3 R 2 and R be the radial stresses at radius being r3 the inner, intermediate and outer surfaces. We will call the difference between the inside radius of the jacket and
,
if
MISCELLANEOUS PROBLEMS.
after assembling e 2
is
151
of the tube
and
el
the decrease in the length of the radius the increase in the length of the radius
of the jacket,
we have
e
=e +
2
er
(1)
If
is
tube and
the hoop compression on the outside surface of the the hoop tension on the inside surface of the l
due
to the stress
will
be
(Chapter
I),
due to the
lt
will
be
hence
E
or,
#2
^=-'
(2)
in this cylinder, equation of the will article (13) give us a formula for the preceding
hoop compression at the outer surface of the tube, if we let S = 0, Si = R 2 and r = r2 at the same time changing r2 of This gives us the equation equation (13) to r3 and r x to r2
,
.
r2
-- r
o 6 r2 2
,- 2 (r2
- r 3
There being no external pressure on the jacket, equation (13) of the preceding article will also give us a formula for the
S =
hoop tension at the inner surface of the jacket if we put = R2 and r = r2 This gives us the equation 0, S l
.
152
STRENGTH OF MATERIAL.
Taking the factor R 2 from the right side of equations (3) and (4) all the quantities that remain are known (they being
the different radii).
Calling the value of these remaining quantities in equation (3) C i and those for equation (4) C 2
,
we have
#2=^1
and
(5)
#i
dividing
(5)
= -ttA;
R we
2
(6)
by
(6) to
eliminate
have
!--!
Solving the simultaneous equations
(2)
and
(7) for
and
#2 gives
CEe
and
Equations (8) and (9) give the hoop stresses at the joint, and having these we can from either of the equations (3) or (4) find the value of R 2 Having R 2 equation (13) of the will article give us the value of the hoop compreceding
.
pression at the inner surface of the tube, at which place the hoop compressive stress is obviously greatest when the gun
is
At the instant of firing a gun the internal presat rest. sure becomes very great and both the tube and jacket will then be under hoop tensile stress, but obviously the first
of the internal pressure must be to overcome the compressive stress in the tube, though it increases
effect
initial
the tensile stress in the outer hoops where the effect of the internal pressure is least; thus the built-up gun can sustain
greater internal pressures than the solid gun.
MISCELLANEOUS PROBLEMS.
82.
153
a body of mass
Stress
Due
to
a Centrifugal Force.
If
m, at the end of a cord, is whirled round in a circle the cord will be put in tension, the centrifugal force, as we have
learned from mechanics, being equal to
linear velocity
,
where v
is
the
and
is
the
number
of
revolutions per second, the angular velocity aj will be equal As the linear velocity is raj, the tension of the cord to 2 nn.
in
will
be equal to
WxWr
[m
V
W and
g
a>
2nn
\
1
Consider a fly-wheel, the spokes of which represent a comparatively small part of the total weight, so that we may
consider
all the weight as being at the rim of the wheel. Let the thickness of the rim be t and its distance from the
r. Let the weight of the material be per unit volume, and the breadth of the rim a units. Then the total weight of the rim will be w 2 nrta. The
axis of rotation be
Ibs.
is
2 nrta X 4
xWr
be
and the
_w
This
will give
2 xrta
4 x2n 2r
4 n 2 n 2 rt
9(2xra)
us the radial stress for a rim so thin that the be considered uniform throughout the section. may we consider a thick rim whose inside radius is If, however, r2 and whose outside radius is r 1? the increment of radial stress on a circular element whose thickness is dr will be
stress
154
STRENGTH OF MATERIAL.
given by the above formula. We will have then for the increment of radial stress on this elemental volume
dR = -
xWrdr
-,
(1)
the value of this increment having the negative sign because the radial stress decreases as the distance from the
To prove this latter statement, and length / rotates about of uniform section a bar suppose an axis through its end. Let a be the sectional area, w the
axis of rotation increases.
weight per unit volume, and x the distance of any point P from the axis of rotation. The stress at any point P is due to the centrifugal force of the part of the rod beyond P;
therefore, as the center of gravity of this part
l
is
at a dis-
+
l
tance
its
weight
is
a (I
x}w, the
centrifugal force,
article is
by the formula,
c.r.It is clear
TO(
2
*
~* 2)a
zero,
and when x
it
is
maximum.
the integration of
(1)
gives
2
7i
n 2 wr 2
being the constant of integration. We know the value of the radial stress at the outer edge of the rim is zero;
therefore
when
MISCELLANEOUS PROBLEMS.
from which
155
hence,
R =
^
^
W-
H).
(2)
This equation gives the radial stress at any distance r from the axis of rotation. Now considering the equilibrium of any particle, we have,
same two
(3)
H+R =C
rdR
Rdr
Hdr.
(4)
Substituting in
(2)
(4)
the values of
and dR from
(1)
and
we have
r
4 xWwrdr 9
4 n*n 2 w
(r*
dr
Hdr.
20
when
0,
we have
HEquations
(2)
^W
^
r>).
(5)
give the radial and hoop tensile stress any point at a distance r from the axis of and both are independent of r2 Therefore these rotation, to solid be such can as a grindstone, wheels, applied equations
and
(5)
respectively for
As in the preceding article these as well as to fly-wheels. formulae have been deduced without considering the lateral deformation of Art. 79. The true hoop tension, taking this
lateral
H =H
l
kR
STRENGTH OF MATERIAL.
true radial stress
is
radial stress
greatest where r
R =R =
t
kH.
r2 (equation (2)),
this value of r
we have
R,=
5/
-(V is
krS
r2
A;r 2 ).
(6)
greatest where r
rl
hence
From equations (6) and (7) it is clear that the hoop tension, being the greater stress, will be the cause of rupture and also that the rupture will begin at the outside surface of the rim.
83. Bending Due to Centrifugal Force. bending moment, due to centrifugal force,
We
if
move in circles, for example between the two driving wheels of a locomotive. In this case each point of the rod at any instant is moving in a circle, and the centrifugal force due to this motion acts in the direction of the center of that circle for
straight- rod are constrained to
that instant.
site direction.
The
is
stress
Obviously the
horizontal rod
rod
itself acts
down, as does
at its lowest point, for here the weight of the also the stress due to centrifugal
Calling the radius of the circle described by the ends of the rod r, and w the weight per unit length of the rod (considered of uniform cross-section) , the radial stress due to
force.
gr
The value
of the linear velocity v is obtained from our of the speed of the engine, radius of the drive knowledge etc. For wheels, example, if the speed of the engine is S,
MISCELLANEOUS PROBLEMS.
radius of the drive wheels r 1;
157
motion of the
and radius
of
r,
and
this gives
2
R
This value of
wS
R R
formly with
uniform throughout the length of the rod; may be considered as a beam loaded uniper unit length, and will have in addition
is
Fig. 71.
when
at its lowest position a uniform load due to its own The stress at any point can then be readily found weight.
l y connecting rod offers an important example of bending stress due to centrifugal force, but in this case one end of the
for bending,
rod
is
constrained to
move
end moves
effect is
in a circle.
necting rod), if the end of the connecting rod is above the center of motion of the crank arm, the weight of the connecting rod will act down, while the line of action of the
158
stress
STRENGTH OF MATERIAL.
due to the centrifugal force, will act upward, in a direction parallel to the crank arm. Therefore, as before, the
greater stress will be produced when the end of the connecting rod is below the center of motion of the crank arm. In
however, the force acting on the piston will put the connecting rod in tension, so that it can readily sustain this bending stress. When the end of the connecting rod
this position,
is
above the center of motion of the crank arm, the stress, produced by the pressure on the piston, is compressive and
is in the condition of a strut; any bendto due centrifugal force will now become an important ing matter (Chapter XI). Taking the position then as shown in Fig. 71, the centrifugal load at any point of the connecting rod will vary directly as the distance of the point from A; for as the radial stress at any point due to the
wv 2
motion of the connecting rod
is
equal to
gr
where
r is the
radius of the circle being described by the point at the instant and the value of v is the linear velocity of the point B,
because the whole connecting rod, at the instant, is moving in a direction tangential to the circle described by B. Obviously r varies from a at B to an infinite length at A;
therefore,
maximum
at B,
where
it is
- equal to ga
wv 2
The bending
for the origin, is
moment due
<
wv 2
6 ga\
(Ix
x\
)
along
to
being the length of the connecting rod and x the distance This bending moment tends it from A to any point.
bend the rod so that the middle of it will move upward. The weight of the rod itself acts vertically downward, and the
MISCELLANEOUS PROBLEMS.
component
will
159
of the weight
be
cos
moment
is
move
total
Having the bending moment at any point due to the motion and weight of the rod, the stress due to these causes is readily
found from
But
it
may
necting rod, in addition to the above stress, suffers a compressive stress, when in this position, due to the pressure on
the piston, and also a bending stress due to this compressive load, which puts the rod in the condition of the column or
strut discussed in Chapter XI.
will
it
be seen that the comparatively slight bending, due to centrifugal force, assumes important dimensions when we
consider that the least variation of the axis of the connecting rod, from the line of action of this large compressive load,
Flat Plates.
plate
when subjected
Experiment has proved that a circular to too great a pressure on one side
Any diameter, then, of a circular plate, is perpendicular to the greatest tensile stress due to bending, caused by the pressure on one side of the plate. Let us consider a circular plate simply supported at the circumference, and subjected to a uniformly distributed load on the side opposite to the support. If the plate were fixed at
160
STRENGTH OF MATERIAL.
it
the circumference,
beam fixed at the ends is capable of supporting a greater load than if it were free at the ends. We will consider our support as a ring on which the plate rests, the pressure being uniformly distributed on the upper
considering, just as a
side.
Let Fig. 72 represent such a plate, the support being at the We must circumference, and the load w Ibs. per unit area.
Fig. 72.
first find
the bending
moment
at the diameter
T
is
.
AB.
The
rdd,
and the
it is
w
ft
dd.
The supporting
force
rdd must be equal to this load, and its distance from the is r cos 6. The center of gravity of the unidiameter
AB
form load on the triangular element is at a distance r from r cos the center and from the diameter AB. The bending moment at the diameter AB due to these two forces
is
then
dM=
WT --
MISCELLANEOUS PROBLEMS.
Integrating between the limits
161
- and
2
3
for 6,
M
which
the
is
= wr
the bending
moment due
t
the diameter
AB.
Letting
rt
-
moment
through
AB
about the
neutral axis
is
We
of bending,
=
y
I
j 2 /
'
_wr
:
6
t_
~ W
r>
~3~"~2'7?
T^
on any section through a diameter. In we would know the pressure to which it would be subjected and the dimensions of the opening it would cover, so if we put the limiting tensile strength of the material we are to use for p, we can solve the above
which gives the
stress
equation for t, the thickness necessary. If the load instead of being uniform is a concentrated one, and supposing it is to be at the most effective calling it
position, the center, and to bear uniformly on a small circle of radius ^ concentric with the supporting ring, the part of
,and
its center
The
7i
supporting force will be uniform throughout the length of the semicircle of the ring on the same side of the diameter as
this load,
162
STRENGTH OF MATERIAL.
-
distance
2r -
on
W
.
at the
diameter
be
moment of
inertia
rt
as before,
we have
the section
- - = = My 7
W
TT
/
[
2
r
rA
_I|.
p
If
W
2
/
1
2
1
r,\
3 /
rt*
xt
3 r )
if
will
to nr 2 w
/2
and
if
rt
0,
or the load
is
concentrated at a point,
3
stress given by these formulae is the maximum stress, which occurs, as one would expect, at the center of the plate. Experiment proves this to be the case, for such plates begin to crack at the center and the crack extends from there, along
The
a diameter, to the edge of the plate. Experiment also proves the above formula to give very approximate results, so, though this may be a tentative method of deducing them (the
strictly true),
they
MISCELLANEOUS PROBLEMS.
Rectangular
Plates.
163
Experiment
gular plates, when the length is not the width, will crack along
a diagonal.
sides are a
Therefore,
if
the
73),
and
(Fig.
of
---a
thickness
form
Fig. 73.
wab
the
diagonal will be
JL
and
its
or
- from the
diagonal.
Assuming the supporting force to be uniform along the edges, the part acting along the edge a will act at its center of
gravity, which
is
at a distance
- from
fj
the diagonal, as
is
also
the center of gravity of the part acting along the edge b. These two edges will support the whole load on this side of
the diagonal, or the whole supporting force here will equal
is
wab x
.
wab x
I
wabx
"
23
.
12
moment
of inertia
is
through
it
about
of
its
neutral axis
/=
at
1
2,
and y
= -
The equation
bending gives us
t
My
wabx
12
12
~ wabx
2qt
2
'
*2 'at*
164
STRENGTH OF MATERIAL.
,
2 2 Referring to the figure, g = \/a + b and from similar Da = triangles x substituting these values, 2 2
Va +
p=
If
wa 2 b 2
2 (a 2
b,
) t
the plate
is
square, a
and we have
P=
wa 2
4?'
These formulae should for practical purposes have a factor on the right member of the equation of 1.5 if the support is & fixed one (riveted joint), and of 5 if there is only a simple
support.
The formula for elliptical plates, which experiment shows break along the major axis, is, for wrought iron and steel plates simply supported around the edges,
wa 2 b 2
P ~*'
(if
2 t 2
(a
+
is
cast iron is
3 instead of f ) where
,
is
the thickness, and a and b the semi-major and semi-minor axes respectively. The theoretthe load per unit area,
very
difficult
because
it
involves elliptical integrals and because the supporting force is not uniform around the edge, as indeed is also the case
for rectangular plates, but the variation for the latter is not excessive unless the plate is more than two or three times
as long as
true.
it is
wide.
In fact
all
assumptions made are not strictly formula?, however, agree closely with the results obtained experimentally and may be assumed correct for
The
all
practical purposes. subject of flat plates is probably the most unsatisfactory one in the study of strength of material, and practi-
The
cal engineers
have
different
methods
for each
form of
plate.
MISCELLANEOUS PROBLEMS.
Fault
165
may
methods, though they all give approximate results. 85. The principle of least work may be stated as follows: For stable equilibrium the stresses in any structure must have such values that the potential energy of the system is a minimum. The stresses of course must be within
the elastic limit of the material.
When
forces act
upon
to determine
some unknown
is
reaction.
that of a four-legged
table which supports an unsymmetrically placed load. can get from our knowledge of statics three equations to
We
find the part of the load supported by each leg, and the solution can be arrived at by means of the fourth condition fur-
by the principle of least work. Distribution of Stress have all along assumed that As a matter of the stress is uniform throughout a section.
nished
We
It
that the shearing stress in a rod of square section varies as the ordinates of a parabola, being zero where the normal
stress
due to bending
is
maximum, and
maximum where
the normal stress due to bending is zero (at the neutral surface). Again, the shear parallel to the neutral axis in
it
is
zero,
When
is
applied to a piece
not instantaneously produced, but moves with a wave motion through the mass. The velocity
motion can be found, and it is shown to depend the stiffness and density of the material. The velocity upon of stress should be taken into account in problems involving
of this
When
material
is
subjected to force
and deformation occurs the molecules of the material move and this motion is resisted by internal friction. Heat is
166
STRENGTH OF MATERIAL.
produced and for the time between the application of the load and the complete rearrangement of the molecules the stresses at planes through the material are changing; for this time then our formulae for planes of maximum stress are not correct.
Experiment proves that material break if subjected to repeated stress, even if the stress be somewhat below the ultimate strength of the material. Experiment also shows that the greater the numwill
Fatigue of Materials.
ber of applications the less becomes the value of the stress necessary to cause rupture. For example, about a hun-
dred thousand applications of a stress of 49,000 Ibs. to wrought iron will cause rupture, but if 500,000 applications
were made the stress need be only 39,000 Ibs. The loss of strength due to repeated stress is known as the fatigue of
materials.
This fatigue
is
more marked
if
The preceding facts have been mentioned to give the student the knowledge of their existence so that if inclined
he
may
ject.
look them up in more complete works on the subThe time limit of the course for which this book has
been written precludes the possibility of entering into discussion of many subjects of importance, such as the stress in hooks, links, springs, rollers, foundations, arches and
many
others.
Miscellaneous Examples:
1.
reinforced concrete
ins.
long and 5
of the
deep.
is
It
beam is 48 ins. wide, 54 ins. has a sectional area of 3.6 sq. in.
which
is
beam which
per
E CTjl
tral surface,
Use
=10.)
c
and the
Ans.
MISCELLANEOUS PROBLEMS.
2.
167
reinforced concrete
ins.
deep. center of gravity is f ins. below the top of the beam. The load is uniform and equals 3600 Ibs. per in. Find the position of the neutral surface and the length.
sq. in.
wide and 5
The
and
its
77
and
steel.
10.
Ans.
3.
ins.
^c from top.
If
sq. in.,
and that
if
centage of steel
ins.
for steel be 10,000 Ibs. per sq. in., what permust be put in a beam 20 ins. wide by 10
is
deep
the steel
at a distance of 9 ins.
Ans.
4.
0.75%.
the allowable unit stresses for concrete and steel are
Ibs.
If
per sq.
moment
of a
beam
is
1%
and
beam?
Ans.
5.
92,800
is
in.-lbs.
A beam
of the
ft.
long and
ft.
wide.
The concrete
is
is 1 in.
tom
beam.
J in.
if
What
sary?
square bars, what should be the distance a floor is made in this way?
The
is
put under a
Ans.
7.
bar
J,
what
bar
is
What
64,000 Ibs.?
168
8.
STRENGTH OF MATERIAL.
inside radius of a cylinder is 6 ins., its outside The internal pressure is 600 Ibs. per sq. in., the external pressure is that due to the atmosphere.
is 1 ft.
The
radius
and
What
Ans.
9.
and
and
midway between
these surfaces?
Hoop
solid cylinder is
of 14,000 Ibs. per sq. in. Show that the stresses are uniform and give values.
10.
gun
ins.,
is
and a jacket 2 ins. thick. Before assembling, the difference between the outside radius of the tube and the inside radius of the jacket was .004 in. What are the stresses at the outside and inside surfaces?
radius 5
Ans.
11.
Hoop
compression, 14,400
Ibs.
per sq.
in.
firing
the
gun
tube?
12.
r3
The
3.04
radii of a
ins., r2
5.8 ins.,
gun composed of tube and jacket are and ^ = 9.75 ins. The allow-
is 50,000 Ibs. per sq. in. for both tension arid compression. What are the radii before assembling? Ans. Radius of bore, 3.0451 ins.; outside radius of tube,
5.805
ins.;
ins.;
outer radius,
9.7436
13.
ins.
internal powder pressure will stress the gun of 12 to example just 50,000 Ibs. per sq. in. tension? Ans. 51,100 Ibs. per sq. in.
14.
What
What
it is
is
ft.
fly-wheel 30
in diameter,
the greatest tangential stress in a cast-iron rim 1 in. thick and 4 ins. wide,
when
Ans.
making 60 revolutions per minute? Very roughly, 800 Ibs. per sq. in.
MISCELLANEOUS PROBLEMS.
15.
169
What
is
a linear velocity of 1 mile a minute? Ans. Roughly, 750 Ibs. per sq. in.
16. What diameter should a fly-wheel have if it is to make 100 revolutions per minute, and the maximum allow-
is
6000
ft.
ft.
per min.?
Ans.
17.
Roughly, 19
cast-iron bar 9
ft.
and 2
ins.
thick
revolves about an axis } in. in diameter passed through it How many revolutions at a distance of 4| ft. from one end.
the circumference?
How many
force,
if
the area of
its
section be 1.5
sq. ins.?
20.
cast-iron fly-wheel,
ins.
10 sq.
What
is
the stress?
the thickness of a cast-iron cylinder diameter, allowable stress 3600 Ibs. per sq. in., to sustain a load of 250 Ibs. per sq. in.? Ans. 5 ins.
21.
What must be
ins. in
head 36
in.,
stress for steel being 12,000 Ibs. per sq. thick would a steel head for the cylinder of example 21 have to be?
22.
The allowable
how
Ans.
2.6 ins.
170
23.
STRENGTH OF MATERIAL.
ins. thick.
circular steel plate is 24 ins. in diameter and 1.5 It carries a load of 4000 Ibs. at the center rest1
ing on a circle of
stress?
in.
diameter.
What
is
the
maximum
Ans.
24.
1650
Ibs.
per sq.
in.
of
Ans.
25.
per sq.
in.
What must be
ft.
What uniform
in. thick,
plate f
ft.
Ans.
27.
About 12
Ibs.
per sq.
in.
ft.
floor 18
ft.
long, 15
wide
is
made
of concrete
ins. thick,
apart and at
floor
square wrought-iron rods, spaced 1 ft. from the bottom of the concrete. The carries a load of 150 Ibs. per sq. ft. What is the maxi.75 in.
with
1 in.
mum
stress?
E = Ec
s
15.
Ibs.
Ans. Stress
28.
is.
about 450
per sq.
in.
An
22
sq.
Ibs.
in.,
has a major axis 24 ins. under a uniform pressure of ins., The allowable stress is 3000 Ibs. per
and
is
What must
Ans.
BERKELEY
THIS BOOK IS DUE ON THE LAST DATE
STAMPED BELOW
Books not returned on time are subject to a fine of 50c t>er volume after the third day overdue, increasing to $1.00 per volume after the sixth day. Books not in
if
application
is
'made before
DEC
13
EC
'
IEC
8 H
20
1926
FER
OCT
28
1!
OCT
20
50m-7,'16
3C0375